Loading...
Note: File does not exist in v3.15.
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Mediatek MT7530 DSA Switch driver
4 * Copyright (C) 2017 Sean Wang <sean.wang@mediatek.com>
5 */
6#include <linux/etherdevice.h>
7#include <linux/if_bridge.h>
8#include <linux/iopoll.h>
9#include <linux/mdio.h>
10#include <linux/mfd/syscon.h>
11#include <linux/module.h>
12#include <linux/netdevice.h>
13#include <linux/of_mdio.h>
14#include <linux/of_net.h>
15#include <linux/of_platform.h>
16#include <linux/phylink.h>
17#include <linux/regmap.h>
18#include <linux/regulator/consumer.h>
19#include <linux/reset.h>
20#include <linux/gpio/consumer.h>
21#include <net/dsa.h>
22
23#include "mt7530.h"
24
25/* String, offset, and register size in bytes if different from 4 bytes */
26static const struct mt7530_mib_desc mt7530_mib[] = {
27 MIB_DESC(1, 0x00, "TxDrop"),
28 MIB_DESC(1, 0x04, "TxCrcErr"),
29 MIB_DESC(1, 0x08, "TxUnicast"),
30 MIB_DESC(1, 0x0c, "TxMulticast"),
31 MIB_DESC(1, 0x10, "TxBroadcast"),
32 MIB_DESC(1, 0x14, "TxCollision"),
33 MIB_DESC(1, 0x18, "TxSingleCollision"),
34 MIB_DESC(1, 0x1c, "TxMultipleCollision"),
35 MIB_DESC(1, 0x20, "TxDeferred"),
36 MIB_DESC(1, 0x24, "TxLateCollision"),
37 MIB_DESC(1, 0x28, "TxExcessiveCollistion"),
38 MIB_DESC(1, 0x2c, "TxPause"),
39 MIB_DESC(1, 0x30, "TxPktSz64"),
40 MIB_DESC(1, 0x34, "TxPktSz65To127"),
41 MIB_DESC(1, 0x38, "TxPktSz128To255"),
42 MIB_DESC(1, 0x3c, "TxPktSz256To511"),
43 MIB_DESC(1, 0x40, "TxPktSz512To1023"),
44 MIB_DESC(1, 0x44, "Tx1024ToMax"),
45 MIB_DESC(2, 0x48, "TxBytes"),
46 MIB_DESC(1, 0x60, "RxDrop"),
47 MIB_DESC(1, 0x64, "RxFiltering"),
48 MIB_DESC(1, 0x6c, "RxMulticast"),
49 MIB_DESC(1, 0x70, "RxBroadcast"),
50 MIB_DESC(1, 0x74, "RxAlignErr"),
51 MIB_DESC(1, 0x78, "RxCrcErr"),
52 MIB_DESC(1, 0x7c, "RxUnderSizeErr"),
53 MIB_DESC(1, 0x80, "RxFragErr"),
54 MIB_DESC(1, 0x84, "RxOverSzErr"),
55 MIB_DESC(1, 0x88, "RxJabberErr"),
56 MIB_DESC(1, 0x8c, "RxPause"),
57 MIB_DESC(1, 0x90, "RxPktSz64"),
58 MIB_DESC(1, 0x94, "RxPktSz65To127"),
59 MIB_DESC(1, 0x98, "RxPktSz128To255"),
60 MIB_DESC(1, 0x9c, "RxPktSz256To511"),
61 MIB_DESC(1, 0xa0, "RxPktSz512To1023"),
62 MIB_DESC(1, 0xa4, "RxPktSz1024ToMax"),
63 MIB_DESC(2, 0xa8, "RxBytes"),
64 MIB_DESC(1, 0xb0, "RxCtrlDrop"),
65 MIB_DESC(1, 0xb4, "RxIngressDrop"),
66 MIB_DESC(1, 0xb8, "RxArlDrop"),
67};
68
69static int
70mt7623_trgmii_write(struct mt7530_priv *priv, u32 reg, u32 val)
71{
72 int ret;
73
74 ret = regmap_write(priv->ethernet, TRGMII_BASE(reg), val);
75 if (ret < 0)
76 dev_err(priv->dev,
77 "failed to priv write register\n");
78 return ret;
79}
80
81static u32
82mt7623_trgmii_read(struct mt7530_priv *priv, u32 reg)
83{
84 int ret;
85 u32 val;
86
87 ret = regmap_read(priv->ethernet, TRGMII_BASE(reg), &val);
88 if (ret < 0) {
89 dev_err(priv->dev,
90 "failed to priv read register\n");
91 return ret;
92 }
93
94 return val;
95}
96
97static void
98mt7623_trgmii_rmw(struct mt7530_priv *priv, u32 reg,
99 u32 mask, u32 set)
100{
101 u32 val;
102
103 val = mt7623_trgmii_read(priv, reg);
104 val &= ~mask;
105 val |= set;
106 mt7623_trgmii_write(priv, reg, val);
107}
108
109static void
110mt7623_trgmii_set(struct mt7530_priv *priv, u32 reg, u32 val)
111{
112 mt7623_trgmii_rmw(priv, reg, 0, val);
113}
114
115static void
116mt7623_trgmii_clear(struct mt7530_priv *priv, u32 reg, u32 val)
117{
118 mt7623_trgmii_rmw(priv, reg, val, 0);
119}
120
121static int
122core_read_mmd_indirect(struct mt7530_priv *priv, int prtad, int devad)
123{
124 struct mii_bus *bus = priv->bus;
125 int value, ret;
126
127 /* Write the desired MMD Devad */
128 ret = bus->write(bus, 0, MII_MMD_CTRL, devad);
129 if (ret < 0)
130 goto err;
131
132 /* Write the desired MMD register address */
133 ret = bus->write(bus, 0, MII_MMD_DATA, prtad);
134 if (ret < 0)
135 goto err;
136
137 /* Select the Function : DATA with no post increment */
138 ret = bus->write(bus, 0, MII_MMD_CTRL, (devad | MII_MMD_CTRL_NOINCR));
139 if (ret < 0)
140 goto err;
141
142 /* Read the content of the MMD's selected register */
143 value = bus->read(bus, 0, MII_MMD_DATA);
144
145 return value;
146err:
147 dev_err(&bus->dev, "failed to read mmd register\n");
148
149 return ret;
150}
151
152static int
153core_write_mmd_indirect(struct mt7530_priv *priv, int prtad,
154 int devad, u32 data)
155{
156 struct mii_bus *bus = priv->bus;
157 int ret;
158
159 /* Write the desired MMD Devad */
160 ret = bus->write(bus, 0, MII_MMD_CTRL, devad);
161 if (ret < 0)
162 goto err;
163
164 /* Write the desired MMD register address */
165 ret = bus->write(bus, 0, MII_MMD_DATA, prtad);
166 if (ret < 0)
167 goto err;
168
169 /* Select the Function : DATA with no post increment */
170 ret = bus->write(bus, 0, MII_MMD_CTRL, (devad | MII_MMD_CTRL_NOINCR));
171 if (ret < 0)
172 goto err;
173
174 /* Write the data into MMD's selected register */
175 ret = bus->write(bus, 0, MII_MMD_DATA, data);
176err:
177 if (ret < 0)
178 dev_err(&bus->dev,
179 "failed to write mmd register\n");
180 return ret;
181}
182
183static void
184core_write(struct mt7530_priv *priv, u32 reg, u32 val)
185{
186 struct mii_bus *bus = priv->bus;
187
188 mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
189
190 core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
191
192 mutex_unlock(&bus->mdio_lock);
193}
194
195static void
196core_rmw(struct mt7530_priv *priv, u32 reg, u32 mask, u32 set)
197{
198 struct mii_bus *bus = priv->bus;
199 u32 val;
200
201 mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
202
203 val = core_read_mmd_indirect(priv, reg, MDIO_MMD_VEND2);
204 val &= ~mask;
205 val |= set;
206 core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
207
208 mutex_unlock(&bus->mdio_lock);
209}
210
211static void
212core_set(struct mt7530_priv *priv, u32 reg, u32 val)
213{
214 core_rmw(priv, reg, 0, val);
215}
216
217static void
218core_clear(struct mt7530_priv *priv, u32 reg, u32 val)
219{
220 core_rmw(priv, reg, val, 0);
221}
222
223static int
224mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
225{
226 struct mii_bus *bus = priv->bus;
227 u16 page, r, lo, hi;
228 int ret;
229
230 page = (reg >> 6) & 0x3ff;
231 r = (reg >> 2) & 0xf;
232 lo = val & 0xffff;
233 hi = val >> 16;
234
235 /* MT7530 uses 31 as the pseudo port */
236 ret = bus->write(bus, 0x1f, 0x1f, page);
237 if (ret < 0)
238 goto err;
239
240 ret = bus->write(bus, 0x1f, r, lo);
241 if (ret < 0)
242 goto err;
243
244 ret = bus->write(bus, 0x1f, 0x10, hi);
245err:
246 if (ret < 0)
247 dev_err(&bus->dev,
248 "failed to write mt7530 register\n");
249 return ret;
250}
251
252static u32
253mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
254{
255 struct mii_bus *bus = priv->bus;
256 u16 page, r, lo, hi;
257 int ret;
258
259 page = (reg >> 6) & 0x3ff;
260 r = (reg >> 2) & 0xf;
261
262 /* MT7530 uses 31 as the pseudo port */
263 ret = bus->write(bus, 0x1f, 0x1f, page);
264 if (ret < 0) {
265 dev_err(&bus->dev,
266 "failed to read mt7530 register\n");
267 return ret;
268 }
269
270 lo = bus->read(bus, 0x1f, r);
271 hi = bus->read(bus, 0x1f, 0x10);
272
273 return (hi << 16) | (lo & 0xffff);
274}
275
276static void
277mt7530_write(struct mt7530_priv *priv, u32 reg, u32 val)
278{
279 struct mii_bus *bus = priv->bus;
280
281 mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
282
283 mt7530_mii_write(priv, reg, val);
284
285 mutex_unlock(&bus->mdio_lock);
286}
287
288static u32
289_mt7530_read(struct mt7530_dummy_poll *p)
290{
291 struct mii_bus *bus = p->priv->bus;
292 u32 val;
293
294 mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
295
296 val = mt7530_mii_read(p->priv, p->reg);
297
298 mutex_unlock(&bus->mdio_lock);
299
300 return val;
301}
302
303static u32
304mt7530_read(struct mt7530_priv *priv, u32 reg)
305{
306 struct mt7530_dummy_poll p;
307
308 INIT_MT7530_DUMMY_POLL(&p, priv, reg);
309 return _mt7530_read(&p);
310}
311
312static void
313mt7530_rmw(struct mt7530_priv *priv, u32 reg,
314 u32 mask, u32 set)
315{
316 struct mii_bus *bus = priv->bus;
317 u32 val;
318
319 mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
320
321 val = mt7530_mii_read(priv, reg);
322 val &= ~mask;
323 val |= set;
324 mt7530_mii_write(priv, reg, val);
325
326 mutex_unlock(&bus->mdio_lock);
327}
328
329static void
330mt7530_set(struct mt7530_priv *priv, u32 reg, u32 val)
331{
332 mt7530_rmw(priv, reg, 0, val);
333}
334
335static void
336mt7530_clear(struct mt7530_priv *priv, u32 reg, u32 val)
337{
338 mt7530_rmw(priv, reg, val, 0);
339}
340
341static int
342mt7530_fdb_cmd(struct mt7530_priv *priv, enum mt7530_fdb_cmd cmd, u32 *rsp)
343{
344 u32 val;
345 int ret;
346 struct mt7530_dummy_poll p;
347
348 /* Set the command operating upon the MAC address entries */
349 val = ATC_BUSY | ATC_MAT(0) | cmd;
350 mt7530_write(priv, MT7530_ATC, val);
351
352 INIT_MT7530_DUMMY_POLL(&p, priv, MT7530_ATC);
353 ret = readx_poll_timeout(_mt7530_read, &p, val,
354 !(val & ATC_BUSY), 20, 20000);
355 if (ret < 0) {
356 dev_err(priv->dev, "reset timeout\n");
357 return ret;
358 }
359
360 /* Additional sanity for read command if the specified
361 * entry is invalid
362 */
363 val = mt7530_read(priv, MT7530_ATC);
364 if ((cmd == MT7530_FDB_READ) && (val & ATC_INVALID))
365 return -EINVAL;
366
367 if (rsp)
368 *rsp = val;
369
370 return 0;
371}
372
373static void
374mt7530_fdb_read(struct mt7530_priv *priv, struct mt7530_fdb *fdb)
375{
376 u32 reg[3];
377 int i;
378
379 /* Read from ARL table into an array */
380 for (i = 0; i < 3; i++) {
381 reg[i] = mt7530_read(priv, MT7530_TSRA1 + (i * 4));
382
383 dev_dbg(priv->dev, "%s(%d) reg[%d]=0x%x\n",
384 __func__, __LINE__, i, reg[i]);
385 }
386
387 fdb->vid = (reg[1] >> CVID) & CVID_MASK;
388 fdb->aging = (reg[2] >> AGE_TIMER) & AGE_TIMER_MASK;
389 fdb->port_mask = (reg[2] >> PORT_MAP) & PORT_MAP_MASK;
390 fdb->mac[0] = (reg[0] >> MAC_BYTE_0) & MAC_BYTE_MASK;
391 fdb->mac[1] = (reg[0] >> MAC_BYTE_1) & MAC_BYTE_MASK;
392 fdb->mac[2] = (reg[0] >> MAC_BYTE_2) & MAC_BYTE_MASK;
393 fdb->mac[3] = (reg[0] >> MAC_BYTE_3) & MAC_BYTE_MASK;
394 fdb->mac[4] = (reg[1] >> MAC_BYTE_4) & MAC_BYTE_MASK;
395 fdb->mac[5] = (reg[1] >> MAC_BYTE_5) & MAC_BYTE_MASK;
396 fdb->noarp = ((reg[2] >> ENT_STATUS) & ENT_STATUS_MASK) == STATIC_ENT;
397}
398
399static void
400mt7530_fdb_write(struct mt7530_priv *priv, u16 vid,
401 u8 port_mask, const u8 *mac,
402 u8 aging, u8 type)
403{
404 u32 reg[3] = { 0 };
405 int i;
406
407 reg[1] |= vid & CVID_MASK;
408 reg[2] |= (aging & AGE_TIMER_MASK) << AGE_TIMER;
409 reg[2] |= (port_mask & PORT_MAP_MASK) << PORT_MAP;
410 /* STATIC_ENT indicate that entry is static wouldn't
411 * be aged out and STATIC_EMP specified as erasing an
412 * entry
413 */
414 reg[2] |= (type & ENT_STATUS_MASK) << ENT_STATUS;
415 reg[1] |= mac[5] << MAC_BYTE_5;
416 reg[1] |= mac[4] << MAC_BYTE_4;
417 reg[0] |= mac[3] << MAC_BYTE_3;
418 reg[0] |= mac[2] << MAC_BYTE_2;
419 reg[0] |= mac[1] << MAC_BYTE_1;
420 reg[0] |= mac[0] << MAC_BYTE_0;
421
422 /* Write array into the ARL table */
423 for (i = 0; i < 3; i++)
424 mt7530_write(priv, MT7530_ATA1 + (i * 4), reg[i]);
425}
426
427static int
428mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
429{
430 struct mt7530_priv *priv = ds->priv;
431 u32 ncpo1, ssc_delta, trgint, i, xtal;
432
433 xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
434
435 if (xtal == HWTRAP_XTAL_20MHZ) {
436 dev_err(priv->dev,
437 "%s: MT7530 with a 20MHz XTAL is not supported!\n",
438 __func__);
439 return -EINVAL;
440 }
441
442 switch (mode) {
443 case PHY_INTERFACE_MODE_RGMII:
444 trgint = 0;
445 /* PLL frequency: 125MHz */
446 ncpo1 = 0x0c80;
447 break;
448 case PHY_INTERFACE_MODE_TRGMII:
449 trgint = 1;
450 if (priv->id == ID_MT7621) {
451 /* PLL frequency: 150MHz: 1.2GBit */
452 if (xtal == HWTRAP_XTAL_40MHZ)
453 ncpo1 = 0x0780;
454 if (xtal == HWTRAP_XTAL_25MHZ)
455 ncpo1 = 0x0a00;
456 } else { /* PLL frequency: 250MHz: 2.0Gbit */
457 if (xtal == HWTRAP_XTAL_40MHZ)
458 ncpo1 = 0x0c80;
459 if (xtal == HWTRAP_XTAL_25MHZ)
460 ncpo1 = 0x1400;
461 }
462 break;
463 default:
464 dev_err(priv->dev, "xMII mode %d not supported\n", mode);
465 return -EINVAL;
466 }
467
468 if (xtal == HWTRAP_XTAL_25MHZ)
469 ssc_delta = 0x57;
470 else
471 ssc_delta = 0x87;
472
473 mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
474 P6_INTF_MODE(trgint));
475
476 /* Lower Tx Driving for TRGMII path */
477 for (i = 0 ; i < NUM_TRGMII_CTRL ; i++)
478 mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),
479 TD_DM_DRVP(8) | TD_DM_DRVN(8));
480
481 /* Setup core clock for MT7530 */
482 if (!trgint) {
483 /* Disable MT7530 core clock */
484 core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
485
486 /* Disable PLL, since phy_device has not yet been created
487 * provided for phy_[read,write]_mmd_indirect is called, we
488 * provide our own core_write_mmd_indirect to complete this
489 * function.
490 */
491 core_write_mmd_indirect(priv,
492 CORE_GSWPLL_GRP1,
493 MDIO_MMD_VEND2,
494 0);
495
496 /* Set core clock into 500Mhz */
497 core_write(priv, CORE_GSWPLL_GRP2,
498 RG_GSWPLL_POSDIV_500M(1) |
499 RG_GSWPLL_FBKDIV_500M(25));
500
501 /* Enable PLL */
502 core_write(priv, CORE_GSWPLL_GRP1,
503 RG_GSWPLL_EN_PRE |
504 RG_GSWPLL_POSDIV_200M(2) |
505 RG_GSWPLL_FBKDIV_200M(32));
506
507 /* Enable MT7530 core clock */
508 core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
509 }
510
511 /* Setup the MT7530 TRGMII Tx Clock */
512 core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
513 core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
514 core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
515 core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
516 core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
517 core_write(priv, CORE_PLL_GROUP4,
518 RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
519 RG_SYSPLL_BIAS_LPF_EN);
520 core_write(priv, CORE_PLL_GROUP2,
521 RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
522 RG_SYSPLL_POSDIV(1));
523 core_write(priv, CORE_PLL_GROUP7,
524 RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
525 RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
526 core_set(priv, CORE_TRGMII_GSW_CLK_CG,
527 REG_GSWCK_EN | REG_TRGMIICK_EN);
528
529 if (!trgint)
530 for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
531 mt7530_rmw(priv, MT7530_TRGMII_RD(i),
532 RD_TAP_MASK, RD_TAP(16));
533 else
534 if (priv->id != ID_MT7621)
535 mt7623_trgmii_set(priv, GSW_INTF_MODE,
536 INTF_MODE_TRGMII);
537
538 return 0;
539}
540
541static int
542mt7623_pad_clk_setup(struct dsa_switch *ds)
543{
544 struct mt7530_priv *priv = ds->priv;
545 int i;
546
547 for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
548 mt7623_trgmii_write(priv, GSW_TRGMII_TD_ODT(i),
549 TD_DM_DRVP(8) | TD_DM_DRVN(8));
550
551 mt7623_trgmii_set(priv, GSW_TRGMII_RCK_CTRL, RX_RST | RXC_DQSISEL);
552 mt7623_trgmii_clear(priv, GSW_TRGMII_RCK_CTRL, RX_RST);
553
554 return 0;
555}
556
557static void
558mt7530_mib_reset(struct dsa_switch *ds)
559{
560 struct mt7530_priv *priv = ds->priv;
561
562 mt7530_write(priv, MT7530_MIB_CCR, CCR_MIB_FLUSH);
563 mt7530_write(priv, MT7530_MIB_CCR, CCR_MIB_ACTIVATE);
564}
565
566static void
567mt7530_port_set_status(struct mt7530_priv *priv, int port, int enable)
568{
569 u32 mask = PMCR_TX_EN | PMCR_RX_EN;
570
571 if (enable)
572 mt7530_set(priv, MT7530_PMCR_P(port), mask);
573 else
574 mt7530_clear(priv, MT7530_PMCR_P(port), mask);
575}
576
577static int mt7530_phy_read(struct dsa_switch *ds, int port, int regnum)
578{
579 struct mt7530_priv *priv = ds->priv;
580
581 return mdiobus_read_nested(priv->bus, port, regnum);
582}
583
584static int mt7530_phy_write(struct dsa_switch *ds, int port, int regnum,
585 u16 val)
586{
587 struct mt7530_priv *priv = ds->priv;
588
589 return mdiobus_write_nested(priv->bus, port, regnum, val);
590}
591
592static void
593mt7530_get_strings(struct dsa_switch *ds, int port, u32 stringset,
594 uint8_t *data)
595{
596 int i;
597
598 if (stringset != ETH_SS_STATS)
599 return;
600
601 for (i = 0; i < ARRAY_SIZE(mt7530_mib); i++)
602 strncpy(data + i * ETH_GSTRING_LEN, mt7530_mib[i].name,
603 ETH_GSTRING_LEN);
604}
605
606static void
607mt7530_get_ethtool_stats(struct dsa_switch *ds, int port,
608 uint64_t *data)
609{
610 struct mt7530_priv *priv = ds->priv;
611 const struct mt7530_mib_desc *mib;
612 u32 reg, i;
613 u64 hi;
614
615 for (i = 0; i < ARRAY_SIZE(mt7530_mib); i++) {
616 mib = &mt7530_mib[i];
617 reg = MT7530_PORT_MIB_COUNTER(port) + mib->offset;
618
619 data[i] = mt7530_read(priv, reg);
620 if (mib->size == 2) {
621 hi = mt7530_read(priv, reg + 4);
622 data[i] |= hi << 32;
623 }
624 }
625}
626
627static int
628mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset)
629{
630 if (sset != ETH_SS_STATS)
631 return 0;
632
633 return ARRAY_SIZE(mt7530_mib);
634}
635
636static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
637{
638 struct mt7530_priv *priv = ds->priv;
639 u8 tx_delay = 0;
640 int val;
641
642 mutex_lock(&priv->reg_mutex);
643
644 val = mt7530_read(priv, MT7530_MHWTRAP);
645
646 val |= MHWTRAP_MANUAL | MHWTRAP_P5_MAC_SEL | MHWTRAP_P5_DIS;
647 val &= ~MHWTRAP_P5_RGMII_MODE & ~MHWTRAP_PHY0_SEL;
648
649 switch (priv->p5_intf_sel) {
650 case P5_INTF_SEL_PHY_P0:
651 /* MT7530_P5_MODE_GPHY_P0: 2nd GMAC -> P5 -> P0 */
652 val |= MHWTRAP_PHY0_SEL;
653 /* fall through */
654 case P5_INTF_SEL_PHY_P4:
655 /* MT7530_P5_MODE_GPHY_P4: 2nd GMAC -> P5 -> P4 */
656 val &= ~MHWTRAP_P5_MAC_SEL & ~MHWTRAP_P5_DIS;
657
658 /* Setup the MAC by default for the cpu port */
659 mt7530_write(priv, MT7530_PMCR_P(5), 0x56300);
660 break;
661 case P5_INTF_SEL_GMAC5:
662 /* MT7530_P5_MODE_GMAC: P5 -> External phy or 2nd GMAC */
663 val &= ~MHWTRAP_P5_DIS;
664 break;
665 case P5_DISABLED:
666 interface = PHY_INTERFACE_MODE_NA;
667 break;
668 default:
669 dev_err(ds->dev, "Unsupported p5_intf_sel %d\n",
670 priv->p5_intf_sel);
671 goto unlock_exit;
672 }
673
674 /* Setup RGMII settings */
675 if (phy_interface_mode_is_rgmii(interface)) {
676 val |= MHWTRAP_P5_RGMII_MODE;
677
678 /* P5 RGMII RX Clock Control: delay setting for 1000M */
679 mt7530_write(priv, MT7530_P5RGMIIRXCR, CSR_RGMII_EDGE_ALIGN);
680
681 /* Don't set delay in DSA mode */
682 if (!dsa_is_dsa_port(priv->ds, 5) &&
683 (interface == PHY_INTERFACE_MODE_RGMII_TXID ||
684 interface == PHY_INTERFACE_MODE_RGMII_ID))
685 tx_delay = 4; /* n * 0.5 ns */
686
687 /* P5 RGMII TX Clock Control: delay x */
688 mt7530_write(priv, MT7530_P5RGMIITXCR,
689 CSR_RGMII_TXC_CFG(0x10 + tx_delay));
690
691 /* reduce P5 RGMII Tx driving, 8mA */
692 mt7530_write(priv, MT7530_IO_DRV_CR,
693 P5_IO_CLK_DRV(1) | P5_IO_DATA_DRV(1));
694 }
695
696 mt7530_write(priv, MT7530_MHWTRAP, val);
697
698 dev_dbg(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
699 val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));
700
701 priv->p5_interface = interface;
702
703unlock_exit:
704 mutex_unlock(&priv->reg_mutex);
705}
706
707static int
708mt7530_cpu_port_enable(struct mt7530_priv *priv,
709 int port)
710{
711 /* Enable Mediatek header mode on the cpu port */
712 mt7530_write(priv, MT7530_PVC_P(port),
713 PORT_SPEC_TAG);
714
715 /* Disable auto learning on the cpu port */
716 mt7530_set(priv, MT7530_PSC_P(port), SA_DIS);
717
718 /* Unknown unicast frame fordwarding to the cpu port */
719 mt7530_set(priv, MT7530_MFC, UNU_FFP(BIT(port)));
720
721 /* Set CPU port number */
722 if (priv->id == ID_MT7621)
723 mt7530_rmw(priv, MT7530_MFC, CPU_MASK, CPU_EN | CPU_PORT(port));
724
725 /* CPU port gets connected to all user ports of
726 * the switch
727 */
728 mt7530_write(priv, MT7530_PCR_P(port),
729 PCR_MATRIX(dsa_user_ports(priv->ds)));
730
731 return 0;
732}
733
734static int
735mt7530_port_enable(struct dsa_switch *ds, int port,
736 struct phy_device *phy)
737{
738 struct mt7530_priv *priv = ds->priv;
739
740 if (!dsa_is_user_port(ds, port))
741 return 0;
742
743 mutex_lock(&priv->reg_mutex);
744
745 /* Allow the user port gets connected to the cpu port and also
746 * restore the port matrix if the port is the member of a certain
747 * bridge.
748 */
749 priv->ports[port].pm |= PCR_MATRIX(BIT(MT7530_CPU_PORT));
750 priv->ports[port].enable = true;
751 mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
752 priv->ports[port].pm);
753 mt7530_port_set_status(priv, port, 0);
754
755 mutex_unlock(&priv->reg_mutex);
756
757 return 0;
758}
759
760static void
761mt7530_port_disable(struct dsa_switch *ds, int port)
762{
763 struct mt7530_priv *priv = ds->priv;
764
765 if (!dsa_is_user_port(ds, port))
766 return;
767
768 mutex_lock(&priv->reg_mutex);
769
770 /* Clear up all port matrix which could be restored in the next
771 * enablement for the port.
772 */
773 priv->ports[port].enable = false;
774 mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
775 PCR_MATRIX_CLR);
776 mt7530_port_set_status(priv, port, 0);
777
778 mutex_unlock(&priv->reg_mutex);
779}
780
781static void
782mt7530_stp_state_set(struct dsa_switch *ds, int port, u8 state)
783{
784 struct mt7530_priv *priv = ds->priv;
785 u32 stp_state;
786
787 switch (state) {
788 case BR_STATE_DISABLED:
789 stp_state = MT7530_STP_DISABLED;
790 break;
791 case BR_STATE_BLOCKING:
792 stp_state = MT7530_STP_BLOCKING;
793 break;
794 case BR_STATE_LISTENING:
795 stp_state = MT7530_STP_LISTENING;
796 break;
797 case BR_STATE_LEARNING:
798 stp_state = MT7530_STP_LEARNING;
799 break;
800 case BR_STATE_FORWARDING:
801 default:
802 stp_state = MT7530_STP_FORWARDING;
803 break;
804 }
805
806 mt7530_rmw(priv, MT7530_SSP_P(port), FID_PST_MASK, stp_state);
807}
808
809static int
810mt7530_port_bridge_join(struct dsa_switch *ds, int port,
811 struct net_device *bridge)
812{
813 struct mt7530_priv *priv = ds->priv;
814 u32 port_bitmap = BIT(MT7530_CPU_PORT);
815 int i;
816
817 mutex_lock(&priv->reg_mutex);
818
819 for (i = 0; i < MT7530_NUM_PORTS; i++) {
820 /* Add this port to the port matrix of the other ports in the
821 * same bridge. If the port is disabled, port matrix is kept
822 * and not being setup until the port becomes enabled.
823 */
824 if (dsa_is_user_port(ds, i) && i != port) {
825 if (dsa_to_port(ds, i)->bridge_dev != bridge)
826 continue;
827 if (priv->ports[i].enable)
828 mt7530_set(priv, MT7530_PCR_P(i),
829 PCR_MATRIX(BIT(port)));
830 priv->ports[i].pm |= PCR_MATRIX(BIT(port));
831
832 port_bitmap |= BIT(i);
833 }
834 }
835
836 /* Add the all other ports to this port matrix. */
837 if (priv->ports[port].enable)
838 mt7530_rmw(priv, MT7530_PCR_P(port),
839 PCR_MATRIX_MASK, PCR_MATRIX(port_bitmap));
840 priv->ports[port].pm |= PCR_MATRIX(port_bitmap);
841
842 mutex_unlock(&priv->reg_mutex);
843
844 return 0;
845}
846
847static void
848mt7530_port_set_vlan_unaware(struct dsa_switch *ds, int port)
849{
850 struct mt7530_priv *priv = ds->priv;
851 bool all_user_ports_removed = true;
852 int i;
853
854 /* When a port is removed from the bridge, the port would be set up
855 * back to the default as is at initial boot which is a VLAN-unaware
856 * port.
857 */
858 mt7530_rmw(priv, MT7530_PCR_P(port), PCR_PORT_VLAN_MASK,
859 MT7530_PORT_MATRIX_MODE);
860 mt7530_rmw(priv, MT7530_PVC_P(port), VLAN_ATTR_MASK,
861 VLAN_ATTR(MT7530_VLAN_TRANSPARENT));
862
863 for (i = 0; i < MT7530_NUM_PORTS; i++) {
864 if (dsa_is_user_port(ds, i) &&
865 dsa_port_is_vlan_filtering(&ds->ports[i])) {
866 all_user_ports_removed = false;
867 break;
868 }
869 }
870
871 /* CPU port also does the same thing until all user ports belonging to
872 * the CPU port get out of VLAN filtering mode.
873 */
874 if (all_user_ports_removed) {
875 mt7530_write(priv, MT7530_PCR_P(MT7530_CPU_PORT),
876 PCR_MATRIX(dsa_user_ports(priv->ds)));
877 mt7530_write(priv, MT7530_PVC_P(MT7530_CPU_PORT),
878 PORT_SPEC_TAG);
879 }
880}
881
882static void
883mt7530_port_set_vlan_aware(struct dsa_switch *ds, int port)
884{
885 struct mt7530_priv *priv = ds->priv;
886
887 /* The real fabric path would be decided on the membership in the
888 * entry of VLAN table. PCR_MATRIX set up here with ALL_MEMBERS
889 * means potential VLAN can be consisting of certain subset of all
890 * ports.
891 */
892 mt7530_rmw(priv, MT7530_PCR_P(port),
893 PCR_MATRIX_MASK, PCR_MATRIX(MT7530_ALL_MEMBERS));
894
895 /* Trapped into security mode allows packet forwarding through VLAN
896 * table lookup.
897 */
898 mt7530_rmw(priv, MT7530_PCR_P(port), PCR_PORT_VLAN_MASK,
899 MT7530_PORT_SECURITY_MODE);
900
901 /* Set the port as a user port which is to be able to recognize VID
902 * from incoming packets before fetching entry within the VLAN table.
903 */
904 mt7530_rmw(priv, MT7530_PVC_P(port), VLAN_ATTR_MASK,
905 VLAN_ATTR(MT7530_VLAN_USER));
906}
907
908static void
909mt7530_port_bridge_leave(struct dsa_switch *ds, int port,
910 struct net_device *bridge)
911{
912 struct mt7530_priv *priv = ds->priv;
913 int i;
914
915 mutex_lock(&priv->reg_mutex);
916
917 for (i = 0; i < MT7530_NUM_PORTS; i++) {
918 /* Remove this port from the port matrix of the other ports
919 * in the same bridge. If the port is disabled, port matrix
920 * is kept and not being setup until the port becomes enabled.
921 * And the other port's port matrix cannot be broken when the
922 * other port is still a VLAN-aware port.
923 */
924 if (dsa_is_user_port(ds, i) && i != port &&
925 !dsa_port_is_vlan_filtering(&ds->ports[i])) {
926 if (dsa_to_port(ds, i)->bridge_dev != bridge)
927 continue;
928 if (priv->ports[i].enable)
929 mt7530_clear(priv, MT7530_PCR_P(i),
930 PCR_MATRIX(BIT(port)));
931 priv->ports[i].pm &= ~PCR_MATRIX(BIT(port));
932 }
933 }
934
935 /* Set the cpu port to be the only one in the port matrix of
936 * this port.
937 */
938 if (priv->ports[port].enable)
939 mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
940 PCR_MATRIX(BIT(MT7530_CPU_PORT)));
941 priv->ports[port].pm = PCR_MATRIX(BIT(MT7530_CPU_PORT));
942
943 mutex_unlock(&priv->reg_mutex);
944}
945
946static int
947mt7530_port_fdb_add(struct dsa_switch *ds, int port,
948 const unsigned char *addr, u16 vid)
949{
950 struct mt7530_priv *priv = ds->priv;
951 int ret;
952 u8 port_mask = BIT(port);
953
954 mutex_lock(&priv->reg_mutex);
955 mt7530_fdb_write(priv, vid, port_mask, addr, -1, STATIC_ENT);
956 ret = mt7530_fdb_cmd(priv, MT7530_FDB_WRITE, NULL);
957 mutex_unlock(&priv->reg_mutex);
958
959 return ret;
960}
961
962static int
963mt7530_port_fdb_del(struct dsa_switch *ds, int port,
964 const unsigned char *addr, u16 vid)
965{
966 struct mt7530_priv *priv = ds->priv;
967 int ret;
968 u8 port_mask = BIT(port);
969
970 mutex_lock(&priv->reg_mutex);
971 mt7530_fdb_write(priv, vid, port_mask, addr, -1, STATIC_EMP);
972 ret = mt7530_fdb_cmd(priv, MT7530_FDB_WRITE, NULL);
973 mutex_unlock(&priv->reg_mutex);
974
975 return ret;
976}
977
978static int
979mt7530_port_fdb_dump(struct dsa_switch *ds, int port,
980 dsa_fdb_dump_cb_t *cb, void *data)
981{
982 struct mt7530_priv *priv = ds->priv;
983 struct mt7530_fdb _fdb = { 0 };
984 int cnt = MT7530_NUM_FDB_RECORDS;
985 int ret = 0;
986 u32 rsp = 0;
987
988 mutex_lock(&priv->reg_mutex);
989
990 ret = mt7530_fdb_cmd(priv, MT7530_FDB_START, &rsp);
991 if (ret < 0)
992 goto err;
993
994 do {
995 if (rsp & ATC_SRCH_HIT) {
996 mt7530_fdb_read(priv, &_fdb);
997 if (_fdb.port_mask & BIT(port)) {
998 ret = cb(_fdb.mac, _fdb.vid, _fdb.noarp,
999 data);
1000 if (ret < 0)
1001 break;
1002 }
1003 }
1004 } while (--cnt &&
1005 !(rsp & ATC_SRCH_END) &&
1006 !mt7530_fdb_cmd(priv, MT7530_FDB_NEXT, &rsp));
1007err:
1008 mutex_unlock(&priv->reg_mutex);
1009
1010 return 0;
1011}
1012
1013static int
1014mt7530_vlan_cmd(struct mt7530_priv *priv, enum mt7530_vlan_cmd cmd, u16 vid)
1015{
1016 struct mt7530_dummy_poll p;
1017 u32 val;
1018 int ret;
1019
1020 val = VTCR_BUSY | VTCR_FUNC(cmd) | vid;
1021 mt7530_write(priv, MT7530_VTCR, val);
1022
1023 INIT_MT7530_DUMMY_POLL(&p, priv, MT7530_VTCR);
1024 ret = readx_poll_timeout(_mt7530_read, &p, val,
1025 !(val & VTCR_BUSY), 20, 20000);
1026 if (ret < 0) {
1027 dev_err(priv->dev, "poll timeout\n");
1028 return ret;
1029 }
1030
1031 val = mt7530_read(priv, MT7530_VTCR);
1032 if (val & VTCR_INVALID) {
1033 dev_err(priv->dev, "read VTCR invalid\n");
1034 return -EINVAL;
1035 }
1036
1037 return 0;
1038}
1039
1040static int
1041mt7530_port_vlan_filtering(struct dsa_switch *ds, int port,
1042 bool vlan_filtering)
1043{
1044 if (vlan_filtering) {
1045 /* The port is being kept as VLAN-unaware port when bridge is
1046 * set up with vlan_filtering not being set, Otherwise, the
1047 * port and the corresponding CPU port is required the setup
1048 * for becoming a VLAN-aware port.
1049 */
1050 mt7530_port_set_vlan_aware(ds, port);
1051 mt7530_port_set_vlan_aware(ds, MT7530_CPU_PORT);
1052 } else {
1053 mt7530_port_set_vlan_unaware(ds, port);
1054 }
1055
1056 return 0;
1057}
1058
1059static int
1060mt7530_port_vlan_prepare(struct dsa_switch *ds, int port,
1061 const struct switchdev_obj_port_vlan *vlan)
1062{
1063 /* nothing needed */
1064
1065 return 0;
1066}
1067
1068static void
1069mt7530_hw_vlan_add(struct mt7530_priv *priv,
1070 struct mt7530_hw_vlan_entry *entry)
1071{
1072 u8 new_members;
1073 u32 val;
1074
1075 new_members = entry->old_members | BIT(entry->port) |
1076 BIT(MT7530_CPU_PORT);
1077
1078 /* Validate the entry with independent learning, create egress tag per
1079 * VLAN and joining the port as one of the port members.
1080 */
1081 val = IVL_MAC | VTAG_EN | PORT_MEM(new_members) | VLAN_VALID;
1082 mt7530_write(priv, MT7530_VAWD1, val);
1083
1084 /* Decide whether adding tag or not for those outgoing packets from the
1085 * port inside the VLAN.
1086 */
1087 val = entry->untagged ? MT7530_VLAN_EGRESS_UNTAG :
1088 MT7530_VLAN_EGRESS_TAG;
1089 mt7530_rmw(priv, MT7530_VAWD2,
1090 ETAG_CTRL_P_MASK(entry->port),
1091 ETAG_CTRL_P(entry->port, val));
1092
1093 /* CPU port is always taken as a tagged port for serving more than one
1094 * VLANs across and also being applied with egress type stack mode for
1095 * that VLAN tags would be appended after hardware special tag used as
1096 * DSA tag.
1097 */
1098 mt7530_rmw(priv, MT7530_VAWD2,
1099 ETAG_CTRL_P_MASK(MT7530_CPU_PORT),
1100 ETAG_CTRL_P(MT7530_CPU_PORT,
1101 MT7530_VLAN_EGRESS_STACK));
1102}
1103
1104static void
1105mt7530_hw_vlan_del(struct mt7530_priv *priv,
1106 struct mt7530_hw_vlan_entry *entry)
1107{
1108 u8 new_members;
1109 u32 val;
1110
1111 new_members = entry->old_members & ~BIT(entry->port);
1112
1113 val = mt7530_read(priv, MT7530_VAWD1);
1114 if (!(val & VLAN_VALID)) {
1115 dev_err(priv->dev,
1116 "Cannot be deleted due to invalid entry\n");
1117 return;
1118 }
1119
1120 /* If certain member apart from CPU port is still alive in the VLAN,
1121 * the entry would be kept valid. Otherwise, the entry is got to be
1122 * disabled.
1123 */
1124 if (new_members && new_members != BIT(MT7530_CPU_PORT)) {
1125 val = IVL_MAC | VTAG_EN | PORT_MEM(new_members) |
1126 VLAN_VALID;
1127 mt7530_write(priv, MT7530_VAWD1, val);
1128 } else {
1129 mt7530_write(priv, MT7530_VAWD1, 0);
1130 mt7530_write(priv, MT7530_VAWD2, 0);
1131 }
1132}
1133
1134static void
1135mt7530_hw_vlan_update(struct mt7530_priv *priv, u16 vid,
1136 struct mt7530_hw_vlan_entry *entry,
1137 mt7530_vlan_op vlan_op)
1138{
1139 u32 val;
1140
1141 /* Fetch entry */
1142 mt7530_vlan_cmd(priv, MT7530_VTCR_RD_VID, vid);
1143
1144 val = mt7530_read(priv, MT7530_VAWD1);
1145
1146 entry->old_members = (val >> PORT_MEM_SHFT) & PORT_MEM_MASK;
1147
1148 /* Manipulate entry */
1149 vlan_op(priv, entry);
1150
1151 /* Flush result to hardware */
1152 mt7530_vlan_cmd(priv, MT7530_VTCR_WR_VID, vid);
1153}
1154
1155static void
1156mt7530_port_vlan_add(struct dsa_switch *ds, int port,
1157 const struct switchdev_obj_port_vlan *vlan)
1158{
1159 bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
1160 bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
1161 struct mt7530_hw_vlan_entry new_entry;
1162 struct mt7530_priv *priv = ds->priv;
1163 u16 vid;
1164
1165 /* The port is kept as VLAN-unaware if bridge with vlan_filtering not
1166 * being set.
1167 */
1168 if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
1169 return;
1170
1171 mutex_lock(&priv->reg_mutex);
1172
1173 for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
1174 mt7530_hw_vlan_entry_init(&new_entry, port, untagged);
1175 mt7530_hw_vlan_update(priv, vid, &new_entry,
1176 mt7530_hw_vlan_add);
1177 }
1178
1179 if (pvid) {
1180 mt7530_rmw(priv, MT7530_PPBV1_P(port), G0_PORT_VID_MASK,
1181 G0_PORT_VID(vlan->vid_end));
1182 priv->ports[port].pvid = vlan->vid_end;
1183 }
1184
1185 mutex_unlock(&priv->reg_mutex);
1186}
1187
1188static int
1189mt7530_port_vlan_del(struct dsa_switch *ds, int port,
1190 const struct switchdev_obj_port_vlan *vlan)
1191{
1192 struct mt7530_hw_vlan_entry target_entry;
1193 struct mt7530_priv *priv = ds->priv;
1194 u16 vid, pvid;
1195
1196 /* The port is kept as VLAN-unaware if bridge with vlan_filtering not
1197 * being set.
1198 */
1199 if (!dsa_port_is_vlan_filtering(&ds->ports[port]))
1200 return 0;
1201
1202 mutex_lock(&priv->reg_mutex);
1203
1204 pvid = priv->ports[port].pvid;
1205 for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
1206 mt7530_hw_vlan_entry_init(&target_entry, port, 0);
1207 mt7530_hw_vlan_update(priv, vid, &target_entry,
1208 mt7530_hw_vlan_del);
1209
1210 /* PVID is being restored to the default whenever the PVID port
1211 * is being removed from the VLAN.
1212 */
1213 if (pvid == vid)
1214 pvid = G0_PORT_VID_DEF;
1215 }
1216
1217 mt7530_rmw(priv, MT7530_PPBV1_P(port), G0_PORT_VID_MASK, pvid);
1218 priv->ports[port].pvid = pvid;
1219
1220 mutex_unlock(&priv->reg_mutex);
1221
1222 return 0;
1223}
1224
1225static enum dsa_tag_protocol
1226mtk_get_tag_protocol(struct dsa_switch *ds, int port)
1227{
1228 struct mt7530_priv *priv = ds->priv;
1229
1230 if (port != MT7530_CPU_PORT) {
1231 dev_warn(priv->dev,
1232 "port not matched with tagging CPU port\n");
1233 return DSA_TAG_PROTO_NONE;
1234 } else {
1235 return DSA_TAG_PROTO_MTK;
1236 }
1237}
1238
1239static int
1240mt7530_setup(struct dsa_switch *ds)
1241{
1242 struct mt7530_priv *priv = ds->priv;
1243 struct device_node *phy_node;
1244 struct device_node *mac_np;
1245 struct mt7530_dummy_poll p;
1246 phy_interface_t interface;
1247 struct device_node *dn;
1248 u32 id, val;
1249 int ret, i;
1250
1251 /* The parent node of master netdev which holds the common system
1252 * controller also is the container for two GMACs nodes representing
1253 * as two netdev instances.
1254 */
1255 dn = ds->ports[MT7530_CPU_PORT].master->dev.of_node->parent;
1256
1257 if (priv->id == ID_MT7530) {
1258 priv->ethernet = syscon_node_to_regmap(dn);
1259 if (IS_ERR(priv->ethernet))
1260 return PTR_ERR(priv->ethernet);
1261
1262 regulator_set_voltage(priv->core_pwr, 1000000, 1000000);
1263 ret = regulator_enable(priv->core_pwr);
1264 if (ret < 0) {
1265 dev_err(priv->dev,
1266 "Failed to enable core power: %d\n", ret);
1267 return ret;
1268 }
1269
1270 regulator_set_voltage(priv->io_pwr, 3300000, 3300000);
1271 ret = regulator_enable(priv->io_pwr);
1272 if (ret < 0) {
1273 dev_err(priv->dev, "Failed to enable io pwr: %d\n",
1274 ret);
1275 return ret;
1276 }
1277 }
1278
1279 /* Reset whole chip through gpio pin or memory-mapped registers for
1280 * different type of hardware
1281 */
1282 if (priv->mcm) {
1283 reset_control_assert(priv->rstc);
1284 usleep_range(1000, 1100);
1285 reset_control_deassert(priv->rstc);
1286 } else {
1287 gpiod_set_value_cansleep(priv->reset, 0);
1288 usleep_range(1000, 1100);
1289 gpiod_set_value_cansleep(priv->reset, 1);
1290 }
1291
1292 /* Waiting for MT7530 got to stable */
1293 INIT_MT7530_DUMMY_POLL(&p, priv, MT7530_HWTRAP);
1294 ret = readx_poll_timeout(_mt7530_read, &p, val, val != 0,
1295 20, 1000000);
1296 if (ret < 0) {
1297 dev_err(priv->dev, "reset timeout\n");
1298 return ret;
1299 }
1300
1301 id = mt7530_read(priv, MT7530_CREV);
1302 id >>= CHIP_NAME_SHIFT;
1303 if (id != MT7530_ID) {
1304 dev_err(priv->dev, "chip %x can't be supported\n", id);
1305 return -ENODEV;
1306 }
1307
1308 /* Reset the switch through internal reset */
1309 mt7530_write(priv, MT7530_SYS_CTRL,
1310 SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
1311 SYS_CTRL_REG_RST);
1312
1313 /* Enable Port 6 only; P5 as GMAC5 which currently is not supported */
1314 val = mt7530_read(priv, MT7530_MHWTRAP);
1315 val &= ~MHWTRAP_P6_DIS & ~MHWTRAP_PHY_ACCESS;
1316 val |= MHWTRAP_MANUAL;
1317 mt7530_write(priv, MT7530_MHWTRAP, val);
1318
1319 priv->p6_interface = PHY_INTERFACE_MODE_NA;
1320
1321 /* Enable and reset MIB counters */
1322 mt7530_mib_reset(ds);
1323
1324 mt7530_clear(priv, MT7530_MFC, UNU_FFP_MASK);
1325
1326 for (i = 0; i < MT7530_NUM_PORTS; i++) {
1327 /* Disable forwarding by default on all ports */
1328 mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
1329 PCR_MATRIX_CLR);
1330
1331 if (dsa_is_cpu_port(ds, i))
1332 mt7530_cpu_port_enable(priv, i);
1333 else
1334 mt7530_port_disable(ds, i);
1335 }
1336
1337 /* Setup port 5 */
1338 priv->p5_intf_sel = P5_DISABLED;
1339 interface = PHY_INTERFACE_MODE_NA;
1340
1341 if (!dsa_is_unused_port(ds, 5)) {
1342 priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
1343 interface = of_get_phy_mode(ds->ports[5].dn);
1344 } else {
1345 /* Scan the ethernet nodes. look for GMAC1, lookup used phy */
1346 for_each_child_of_node(dn, mac_np) {
1347 if (!of_device_is_compatible(mac_np,
1348 "mediatek,eth-mac"))
1349 continue;
1350
1351 ret = of_property_read_u32(mac_np, "reg", &id);
1352 if (ret < 0 || id != 1)
1353 continue;
1354
1355 phy_node = of_parse_phandle(mac_np, "phy-handle", 0);
1356 if (phy_node->parent == priv->dev->of_node->parent) {
1357 interface = of_get_phy_mode(mac_np);
1358 id = of_mdio_parse_addr(ds->dev, phy_node);
1359 if (id == 0)
1360 priv->p5_intf_sel = P5_INTF_SEL_PHY_P0;
1361 if (id == 4)
1362 priv->p5_intf_sel = P5_INTF_SEL_PHY_P4;
1363 }
1364 of_node_put(phy_node);
1365 break;
1366 }
1367 }
1368
1369 mt7530_setup_port5(ds, interface);
1370
1371 /* Flush the FDB table */
1372 ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
1373 if (ret < 0)
1374 return ret;
1375
1376 return 0;
1377}
1378
1379static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
1380 unsigned int mode,
1381 const struct phylink_link_state *state)
1382{
1383 struct mt7530_priv *priv = ds->priv;
1384 u32 mcr_cur, mcr_new;
1385
1386 switch (port) {
1387 case 0: /* Internal phy */
1388 case 1:
1389 case 2:
1390 case 3:
1391 case 4:
1392 if (state->interface != PHY_INTERFACE_MODE_GMII)
1393 return;
1394 break;
1395 case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
1396 if (priv->p5_interface == state->interface)
1397 break;
1398 if (!phy_interface_mode_is_rgmii(state->interface) &&
1399 state->interface != PHY_INTERFACE_MODE_MII &&
1400 state->interface != PHY_INTERFACE_MODE_GMII)
1401 return;
1402
1403 mt7530_setup_port5(ds, state->interface);
1404 break;
1405 case 6: /* 1st cpu port */
1406 if (priv->p6_interface == state->interface)
1407 break;
1408
1409 if (state->interface != PHY_INTERFACE_MODE_RGMII &&
1410 state->interface != PHY_INTERFACE_MODE_TRGMII)
1411 return;
1412
1413 /* Setup TX circuit incluing relevant PAD and driving */
1414 mt7530_pad_clk_setup(ds, state->interface);
1415
1416 if (priv->id == ID_MT7530) {
1417 /* Setup RX circuit, relevant PAD and driving on the
1418 * host which must be placed after the setup on the
1419 * device side is all finished.
1420 */
1421 mt7623_pad_clk_setup(ds);
1422 }
1423
1424 priv->p6_interface = state->interface;
1425 break;
1426 default:
1427 dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
1428 return;
1429 }
1430
1431 if (phylink_autoneg_inband(mode)) {
1432 dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
1433 __func__);
1434 return;
1435 }
1436
1437 mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
1438 mcr_new = mcr_cur;
1439 mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
1440 PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
1441 mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
1442 PMCR_BACKPR_EN | PMCR_FORCE_MODE | PMCR_FORCE_LNK;
1443
1444 /* Are we connected to external phy */
1445 if (port == 5 && dsa_is_user_port(ds, 5))
1446 mcr_new |= PMCR_EXT_PHY;
1447
1448 switch (state->speed) {
1449 case SPEED_1000:
1450 mcr_new |= PMCR_FORCE_SPEED_1000;
1451 break;
1452 case SPEED_100:
1453 mcr_new |= PMCR_FORCE_SPEED_100;
1454 break;
1455 }
1456 if (state->duplex == DUPLEX_FULL) {
1457 mcr_new |= PMCR_FORCE_FDX;
1458 if (state->pause & MLO_PAUSE_TX)
1459 mcr_new |= PMCR_TX_FC_EN;
1460 if (state->pause & MLO_PAUSE_RX)
1461 mcr_new |= PMCR_RX_FC_EN;
1462 }
1463
1464 if (mcr_new != mcr_cur)
1465 mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
1466}
1467
1468static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
1469 unsigned int mode,
1470 phy_interface_t interface)
1471{
1472 struct mt7530_priv *priv = ds->priv;
1473
1474 mt7530_port_set_status(priv, port, 0);
1475}
1476
1477static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
1478 unsigned int mode,
1479 phy_interface_t interface,
1480 struct phy_device *phydev)
1481{
1482 struct mt7530_priv *priv = ds->priv;
1483
1484 mt7530_port_set_status(priv, port, 1);
1485}
1486
1487static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
1488 unsigned long *supported,
1489 struct phylink_link_state *state)
1490{
1491 __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
1492
1493 switch (port) {
1494 case 0: /* Internal phy */
1495 case 1:
1496 case 2:
1497 case 3:
1498 case 4:
1499 if (state->interface != PHY_INTERFACE_MODE_NA &&
1500 state->interface != PHY_INTERFACE_MODE_GMII)
1501 goto unsupported;
1502 break;
1503 case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
1504 if (state->interface != PHY_INTERFACE_MODE_NA &&
1505 !phy_interface_mode_is_rgmii(state->interface) &&
1506 state->interface != PHY_INTERFACE_MODE_MII &&
1507 state->interface != PHY_INTERFACE_MODE_GMII)
1508 goto unsupported;
1509 break;
1510 case 6: /* 1st cpu port */
1511 if (state->interface != PHY_INTERFACE_MODE_NA &&
1512 state->interface != PHY_INTERFACE_MODE_RGMII &&
1513 state->interface != PHY_INTERFACE_MODE_TRGMII)
1514 goto unsupported;
1515 break;
1516 default:
1517 dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
1518unsupported:
1519 linkmode_zero(supported);
1520 return;
1521 }
1522
1523 phylink_set_port_modes(mask);
1524 phylink_set(mask, Autoneg);
1525
1526 if (state->interface == PHY_INTERFACE_MODE_TRGMII) {
1527 phylink_set(mask, 1000baseT_Full);
1528 } else {
1529 phylink_set(mask, 10baseT_Half);
1530 phylink_set(mask, 10baseT_Full);
1531 phylink_set(mask, 100baseT_Half);
1532 phylink_set(mask, 100baseT_Full);
1533
1534 if (state->interface != PHY_INTERFACE_MODE_MII) {
1535 phylink_set(mask, 1000baseT_Half);
1536 phylink_set(mask, 1000baseT_Full);
1537 if (port == 5)
1538 phylink_set(mask, 1000baseX_Full);
1539 }
1540 }
1541
1542 phylink_set(mask, Pause);
1543 phylink_set(mask, Asym_Pause);
1544
1545 linkmode_and(supported, supported, mask);
1546 linkmode_and(state->advertising, state->advertising, mask);
1547}
1548
1549static int
1550mt7530_phylink_mac_link_state(struct dsa_switch *ds, int port,
1551 struct phylink_link_state *state)
1552{
1553 struct mt7530_priv *priv = ds->priv;
1554 u32 pmsr;
1555
1556 if (port < 0 || port >= MT7530_NUM_PORTS)
1557 return -EINVAL;
1558
1559 pmsr = mt7530_read(priv, MT7530_PMSR_P(port));
1560
1561 state->link = (pmsr & PMSR_LINK);
1562 state->an_complete = state->link;
1563 state->duplex = !!(pmsr & PMSR_DPX);
1564
1565 switch (pmsr & PMSR_SPEED_MASK) {
1566 case PMSR_SPEED_10:
1567 state->speed = SPEED_10;
1568 break;
1569 case PMSR_SPEED_100:
1570 state->speed = SPEED_100;
1571 break;
1572 case PMSR_SPEED_1000:
1573 state->speed = SPEED_1000;
1574 break;
1575 default:
1576 state->speed = SPEED_UNKNOWN;
1577 break;
1578 }
1579
1580 state->pause &= ~(MLO_PAUSE_RX | MLO_PAUSE_TX);
1581 if (pmsr & PMSR_RX_FC)
1582 state->pause |= MLO_PAUSE_RX;
1583 if (pmsr & PMSR_TX_FC)
1584 state->pause |= MLO_PAUSE_TX;
1585
1586 return 1;
1587}
1588
1589static const struct dsa_switch_ops mt7530_switch_ops = {
1590 .get_tag_protocol = mtk_get_tag_protocol,
1591 .setup = mt7530_setup,
1592 .get_strings = mt7530_get_strings,
1593 .phy_read = mt7530_phy_read,
1594 .phy_write = mt7530_phy_write,
1595 .get_ethtool_stats = mt7530_get_ethtool_stats,
1596 .get_sset_count = mt7530_get_sset_count,
1597 .port_enable = mt7530_port_enable,
1598 .port_disable = mt7530_port_disable,
1599 .port_stp_state_set = mt7530_stp_state_set,
1600 .port_bridge_join = mt7530_port_bridge_join,
1601 .port_bridge_leave = mt7530_port_bridge_leave,
1602 .port_fdb_add = mt7530_port_fdb_add,
1603 .port_fdb_del = mt7530_port_fdb_del,
1604 .port_fdb_dump = mt7530_port_fdb_dump,
1605 .port_vlan_filtering = mt7530_port_vlan_filtering,
1606 .port_vlan_prepare = mt7530_port_vlan_prepare,
1607 .port_vlan_add = mt7530_port_vlan_add,
1608 .port_vlan_del = mt7530_port_vlan_del,
1609 .phylink_validate = mt7530_phylink_validate,
1610 .phylink_mac_link_state = mt7530_phylink_mac_link_state,
1611 .phylink_mac_config = mt7530_phylink_mac_config,
1612 .phylink_mac_link_down = mt7530_phylink_mac_link_down,
1613 .phylink_mac_link_up = mt7530_phylink_mac_link_up,
1614};
1615
1616static const struct of_device_id mt7530_of_match[] = {
1617 { .compatible = "mediatek,mt7621", .data = (void *)ID_MT7621, },
1618 { .compatible = "mediatek,mt7530", .data = (void *)ID_MT7530, },
1619 { /* sentinel */ },
1620};
1621MODULE_DEVICE_TABLE(of, mt7530_of_match);
1622
1623static int
1624mt7530_probe(struct mdio_device *mdiodev)
1625{
1626 struct mt7530_priv *priv;
1627 struct device_node *dn;
1628
1629 dn = mdiodev->dev.of_node;
1630
1631 priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
1632 if (!priv)
1633 return -ENOMEM;
1634
1635 priv->ds = dsa_switch_alloc(&mdiodev->dev, DSA_MAX_PORTS);
1636 if (!priv->ds)
1637 return -ENOMEM;
1638
1639 /* Use medatek,mcm property to distinguish hardware type that would
1640 * casues a little bit differences on power-on sequence.
1641 */
1642 priv->mcm = of_property_read_bool(dn, "mediatek,mcm");
1643 if (priv->mcm) {
1644 dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n");
1645
1646 priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm");
1647 if (IS_ERR(priv->rstc)) {
1648 dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
1649 return PTR_ERR(priv->rstc);
1650 }
1651 }
1652
1653 /* Get the hardware identifier from the devicetree node.
1654 * We will need it for some of the clock and regulator setup.
1655 */
1656 priv->id = (unsigned int)(unsigned long)
1657 of_device_get_match_data(&mdiodev->dev);
1658
1659 if (priv->id == ID_MT7530) {
1660 priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
1661 if (IS_ERR(priv->core_pwr))
1662 return PTR_ERR(priv->core_pwr);
1663
1664 priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io");
1665 if (IS_ERR(priv->io_pwr))
1666 return PTR_ERR(priv->io_pwr);
1667 }
1668
1669 /* Not MCM that indicates switch works as the remote standalone
1670 * integrated circuit so the GPIO pin would be used to complete
1671 * the reset, otherwise memory-mapped register accessing used
1672 * through syscon provides in the case of MCM.
1673 */
1674 if (!priv->mcm) {
1675 priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
1676 GPIOD_OUT_LOW);
1677 if (IS_ERR(priv->reset)) {
1678 dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
1679 return PTR_ERR(priv->reset);
1680 }
1681 }
1682
1683 priv->bus = mdiodev->bus;
1684 priv->dev = &mdiodev->dev;
1685 priv->ds->priv = priv;
1686 priv->ds->ops = &mt7530_switch_ops;
1687 mutex_init(&priv->reg_mutex);
1688 dev_set_drvdata(&mdiodev->dev, priv);
1689
1690 return dsa_register_switch(priv->ds);
1691}
1692
1693static void
1694mt7530_remove(struct mdio_device *mdiodev)
1695{
1696 struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
1697 int ret = 0;
1698
1699 ret = regulator_disable(priv->core_pwr);
1700 if (ret < 0)
1701 dev_err(priv->dev,
1702 "Failed to disable core power: %d\n", ret);
1703
1704 ret = regulator_disable(priv->io_pwr);
1705 if (ret < 0)
1706 dev_err(priv->dev, "Failed to disable io pwr: %d\n",
1707 ret);
1708
1709 dsa_unregister_switch(priv->ds);
1710 mutex_destroy(&priv->reg_mutex);
1711}
1712
1713static struct mdio_driver mt7530_mdio_driver = {
1714 .probe = mt7530_probe,
1715 .remove = mt7530_remove,
1716 .mdiodrv.driver = {
1717 .name = "mt7530",
1718 .of_match_table = mt7530_of_match,
1719 },
1720};
1721
1722mdio_module_driver(mt7530_mdio_driver);
1723
1724MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
1725MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch");
1726MODULE_LICENSE("GPL");