Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Functions to sequence PREFLUSH and FUA writes.
4 *
5 * Copyright (C) 2011 Max Planck Institute for Gravitational Physics
6 * Copyright (C) 2011 Tejun Heo <tj@kernel.org>
7 *
8 * REQ_{PREFLUSH|FUA} requests are decomposed to sequences consisted of three
9 * optional steps - PREFLUSH, DATA and POSTFLUSH - according to the request
10 * properties and hardware capability.
11 *
12 * If a request doesn't have data, only REQ_PREFLUSH makes sense, which
13 * indicates a simple flush request. If there is data, REQ_PREFLUSH indicates
14 * that the device cache should be flushed before the data is executed, and
15 * REQ_FUA means that the data must be on non-volatile media on request
16 * completion.
17 *
18 * If the device doesn't have writeback cache, PREFLUSH and FUA don't make any
19 * difference. The requests are either completed immediately if there's no data
20 * or executed as normal requests otherwise.
21 *
22 * If the device has writeback cache and supports FUA, REQ_PREFLUSH is
23 * translated to PREFLUSH but REQ_FUA is passed down directly with DATA.
24 *
25 * If the device has writeback cache and doesn't support FUA, REQ_PREFLUSH
26 * is translated to PREFLUSH and REQ_FUA to POSTFLUSH.
27 *
28 * The actual execution of flush is double buffered. Whenever a request
29 * needs to execute PRE or POSTFLUSH, it queues at
30 * fq->flush_queue[fq->flush_pending_idx]. Once certain criteria are met, a
31 * REQ_OP_FLUSH is issued and the pending_idx is toggled. When the flush
32 * completes, all the requests which were pending are proceeded to the next
33 * step. This allows arbitrary merging of different types of PREFLUSH/FUA
34 * requests.
35 *
36 * Currently, the following conditions are used to determine when to issue
37 * flush.
38 *
39 * C1. At any given time, only one flush shall be in progress. This makes
40 * double buffering sufficient.
41 *
42 * C2. Flush is deferred if any request is executing DATA of its sequence.
43 * This avoids issuing separate POSTFLUSHes for requests which shared
44 * PREFLUSH.
45 *
46 * C3. The second condition is ignored if there is a request which has
47 * waited longer than FLUSH_PENDING_TIMEOUT. This is to avoid
48 * starvation in the unlikely case where there are continuous stream of
49 * FUA (without PREFLUSH) requests.
50 *
51 * For devices which support FUA, it isn't clear whether C2 (and thus C3)
52 * is beneficial.
53 *
54 * Note that a sequenced PREFLUSH/FUA request with DATA is completed twice.
55 * Once while executing DATA and again after the whole sequence is
56 * complete. The first completion updates the contained bio but doesn't
57 * finish it so that the bio submitter is notified only after the whole
58 * sequence is complete. This is implemented by testing RQF_FLUSH_SEQ in
59 * req_bio_endio().
60 *
61 * The above peculiarity requires that each PREFLUSH/FUA request has only one
62 * bio attached to it, which is guaranteed as they aren't allowed to be
63 * merged in the usual way.
64 */
65
66#include <linux/kernel.h>
67#include <linux/module.h>
68#include <linux/bio.h>
69#include <linux/blkdev.h>
70#include <linux/gfp.h>
71#include <linux/blk-mq.h>
72#include <linux/part_stat.h>
73
74#include "blk.h"
75#include "blk-mq.h"
76#include "blk-mq-tag.h"
77#include "blk-mq-sched.h"
78
79/* PREFLUSH/FUA sequences */
80enum {
81 REQ_FSEQ_PREFLUSH = (1 << 0), /* pre-flushing in progress */
82 REQ_FSEQ_DATA = (1 << 1), /* data write in progress */
83 REQ_FSEQ_POSTFLUSH = (1 << 2), /* post-flushing in progress */
84 REQ_FSEQ_DONE = (1 << 3),
85
86 REQ_FSEQ_ACTIONS = REQ_FSEQ_PREFLUSH | REQ_FSEQ_DATA |
87 REQ_FSEQ_POSTFLUSH,
88
89 /*
90 * If flush has been pending longer than the following timeout,
91 * it's issued even if flush_data requests are still in flight.
92 */
93 FLUSH_PENDING_TIMEOUT = 5 * HZ,
94};
95
96static void blk_kick_flush(struct request_queue *q,
97 struct blk_flush_queue *fq, blk_opf_t flags);
98
99static inline struct blk_flush_queue *
100blk_get_flush_queue(struct request_queue *q, struct blk_mq_ctx *ctx)
101{
102 return blk_mq_map_queue(q, REQ_OP_FLUSH, ctx)->fq;
103}
104
105static unsigned int blk_flush_policy(unsigned long fflags, struct request *rq)
106{
107 unsigned int policy = 0;
108
109 if (blk_rq_sectors(rq))
110 policy |= REQ_FSEQ_DATA;
111
112 if (fflags & (1UL << QUEUE_FLAG_WC)) {
113 if (rq->cmd_flags & REQ_PREFLUSH)
114 policy |= REQ_FSEQ_PREFLUSH;
115 if (!(fflags & (1UL << QUEUE_FLAG_FUA)) &&
116 (rq->cmd_flags & REQ_FUA))
117 policy |= REQ_FSEQ_POSTFLUSH;
118 }
119 return policy;
120}
121
122static unsigned int blk_flush_cur_seq(struct request *rq)
123{
124 return 1 << ffz(rq->flush.seq);
125}
126
127static void blk_flush_restore_request(struct request *rq)
128{
129 /*
130 * After flush data completion, @rq->bio is %NULL but we need to
131 * complete the bio again. @rq->biotail is guaranteed to equal the
132 * original @rq->bio. Restore it.
133 */
134 rq->bio = rq->biotail;
135
136 /* make @rq a normal request */
137 rq->rq_flags &= ~RQF_FLUSH_SEQ;
138 rq->end_io = rq->flush.saved_end_io;
139}
140
141static void blk_flush_queue_rq(struct request *rq, bool add_front)
142{
143 blk_mq_add_to_requeue_list(rq, add_front, true);
144}
145
146static void blk_account_io_flush(struct request *rq)
147{
148 struct block_device *part = rq->q->disk->part0;
149
150 part_stat_lock();
151 part_stat_inc(part, ios[STAT_FLUSH]);
152 part_stat_add(part, nsecs[STAT_FLUSH],
153 ktime_get_ns() - rq->start_time_ns);
154 part_stat_unlock();
155}
156
157/**
158 * blk_flush_complete_seq - complete flush sequence
159 * @rq: PREFLUSH/FUA request being sequenced
160 * @fq: flush queue
161 * @seq: sequences to complete (mask of %REQ_FSEQ_*, can be zero)
162 * @error: whether an error occurred
163 *
164 * @rq just completed @seq part of its flush sequence, record the
165 * completion and trigger the next step.
166 *
167 * CONTEXT:
168 * spin_lock_irq(fq->mq_flush_lock)
169 */
170static void blk_flush_complete_seq(struct request *rq,
171 struct blk_flush_queue *fq,
172 unsigned int seq, blk_status_t error)
173{
174 struct request_queue *q = rq->q;
175 struct list_head *pending = &fq->flush_queue[fq->flush_pending_idx];
176 blk_opf_t cmd_flags;
177
178 BUG_ON(rq->flush.seq & seq);
179 rq->flush.seq |= seq;
180 cmd_flags = rq->cmd_flags;
181
182 if (likely(!error))
183 seq = blk_flush_cur_seq(rq);
184 else
185 seq = REQ_FSEQ_DONE;
186
187 switch (seq) {
188 case REQ_FSEQ_PREFLUSH:
189 case REQ_FSEQ_POSTFLUSH:
190 /* queue for flush */
191 if (list_empty(pending))
192 fq->flush_pending_since = jiffies;
193 list_move_tail(&rq->flush.list, pending);
194 break;
195
196 case REQ_FSEQ_DATA:
197 list_move_tail(&rq->flush.list, &fq->flush_data_in_flight);
198 blk_flush_queue_rq(rq, true);
199 break;
200
201 case REQ_FSEQ_DONE:
202 /*
203 * @rq was previously adjusted by blk_insert_flush() for
204 * flush sequencing and may already have gone through the
205 * flush data request completion path. Restore @rq for
206 * normal completion and end it.
207 */
208 list_del_init(&rq->flush.list);
209 blk_flush_restore_request(rq);
210 blk_mq_end_request(rq, error);
211 break;
212
213 default:
214 BUG();
215 }
216
217 blk_kick_flush(q, fq, cmd_flags);
218}
219
220static enum rq_end_io_ret flush_end_io(struct request *flush_rq,
221 blk_status_t error)
222{
223 struct request_queue *q = flush_rq->q;
224 struct list_head *running;
225 struct request *rq, *n;
226 unsigned long flags = 0;
227 struct blk_flush_queue *fq = blk_get_flush_queue(q, flush_rq->mq_ctx);
228
229 /* release the tag's ownership to the req cloned from */
230 spin_lock_irqsave(&fq->mq_flush_lock, flags);
231
232 if (!req_ref_put_and_test(flush_rq)) {
233 fq->rq_status = error;
234 spin_unlock_irqrestore(&fq->mq_flush_lock, flags);
235 return RQ_END_IO_NONE;
236 }
237
238 blk_account_io_flush(flush_rq);
239 /*
240 * Flush request has to be marked as IDLE when it is really ended
241 * because its .end_io() is called from timeout code path too for
242 * avoiding use-after-free.
243 */
244 WRITE_ONCE(flush_rq->state, MQ_RQ_IDLE);
245 if (fq->rq_status != BLK_STS_OK) {
246 error = fq->rq_status;
247 fq->rq_status = BLK_STS_OK;
248 }
249
250 if (!q->elevator) {
251 flush_rq->tag = BLK_MQ_NO_TAG;
252 } else {
253 blk_mq_put_driver_tag(flush_rq);
254 flush_rq->internal_tag = BLK_MQ_NO_TAG;
255 }
256
257 running = &fq->flush_queue[fq->flush_running_idx];
258 BUG_ON(fq->flush_pending_idx == fq->flush_running_idx);
259
260 /* account completion of the flush request */
261 fq->flush_running_idx ^= 1;
262
263 /* and push the waiting requests to the next stage */
264 list_for_each_entry_safe(rq, n, running, flush.list) {
265 unsigned int seq = blk_flush_cur_seq(rq);
266
267 BUG_ON(seq != REQ_FSEQ_PREFLUSH && seq != REQ_FSEQ_POSTFLUSH);
268 blk_flush_complete_seq(rq, fq, seq, error);
269 }
270
271 spin_unlock_irqrestore(&fq->mq_flush_lock, flags);
272 return RQ_END_IO_NONE;
273}
274
275bool is_flush_rq(struct request *rq)
276{
277 return rq->end_io == flush_end_io;
278}
279
280/**
281 * blk_kick_flush - consider issuing flush request
282 * @q: request_queue being kicked
283 * @fq: flush queue
284 * @flags: cmd_flags of the original request
285 *
286 * Flush related states of @q have changed, consider issuing flush request.
287 * Please read the comment at the top of this file for more info.
288 *
289 * CONTEXT:
290 * spin_lock_irq(fq->mq_flush_lock)
291 *
292 */
293static void blk_kick_flush(struct request_queue *q, struct blk_flush_queue *fq,
294 blk_opf_t flags)
295{
296 struct list_head *pending = &fq->flush_queue[fq->flush_pending_idx];
297 struct request *first_rq =
298 list_first_entry(pending, struct request, flush.list);
299 struct request *flush_rq = fq->flush_rq;
300
301 /* C1 described at the top of this file */
302 if (fq->flush_pending_idx != fq->flush_running_idx || list_empty(pending))
303 return;
304
305 /* C2 and C3 */
306 if (!list_empty(&fq->flush_data_in_flight) &&
307 time_before(jiffies,
308 fq->flush_pending_since + FLUSH_PENDING_TIMEOUT))
309 return;
310
311 /*
312 * Issue flush and toggle pending_idx. This makes pending_idx
313 * different from running_idx, which means flush is in flight.
314 */
315 fq->flush_pending_idx ^= 1;
316
317 blk_rq_init(q, flush_rq);
318
319 /*
320 * In case of none scheduler, borrow tag from the first request
321 * since they can't be in flight at the same time. And acquire
322 * the tag's ownership for flush req.
323 *
324 * In case of IO scheduler, flush rq need to borrow scheduler tag
325 * just for cheating put/get driver tag.
326 */
327 flush_rq->mq_ctx = first_rq->mq_ctx;
328 flush_rq->mq_hctx = first_rq->mq_hctx;
329
330 if (!q->elevator) {
331 flush_rq->tag = first_rq->tag;
332
333 /*
334 * We borrow data request's driver tag, so have to mark
335 * this flush request as INFLIGHT for avoiding double
336 * account of this driver tag
337 */
338 flush_rq->rq_flags |= RQF_MQ_INFLIGHT;
339 } else
340 flush_rq->internal_tag = first_rq->internal_tag;
341
342 flush_rq->cmd_flags = REQ_OP_FLUSH | REQ_PREFLUSH;
343 flush_rq->cmd_flags |= (flags & REQ_DRV) | (flags & REQ_FAILFAST_MASK);
344 flush_rq->rq_flags |= RQF_FLUSH_SEQ;
345 flush_rq->end_io = flush_end_io;
346 /*
347 * Order WRITE ->end_io and WRITE rq->ref, and its pair is the one
348 * implied in refcount_inc_not_zero() called from
349 * blk_mq_find_and_get_req(), which orders WRITE/READ flush_rq->ref
350 * and READ flush_rq->end_io
351 */
352 smp_wmb();
353 req_ref_set(flush_rq, 1);
354
355 blk_flush_queue_rq(flush_rq, false);
356}
357
358static enum rq_end_io_ret mq_flush_data_end_io(struct request *rq,
359 blk_status_t error)
360{
361 struct request_queue *q = rq->q;
362 struct blk_mq_hw_ctx *hctx = rq->mq_hctx;
363 struct blk_mq_ctx *ctx = rq->mq_ctx;
364 unsigned long flags;
365 struct blk_flush_queue *fq = blk_get_flush_queue(q, ctx);
366
367 if (q->elevator) {
368 WARN_ON(rq->tag < 0);
369 blk_mq_put_driver_tag(rq);
370 }
371
372 /*
373 * After populating an empty queue, kick it to avoid stall. Read
374 * the comment in flush_end_io().
375 */
376 spin_lock_irqsave(&fq->mq_flush_lock, flags);
377 blk_flush_complete_seq(rq, fq, REQ_FSEQ_DATA, error);
378 spin_unlock_irqrestore(&fq->mq_flush_lock, flags);
379
380 blk_mq_sched_restart(hctx);
381 return RQ_END_IO_NONE;
382}
383
384/**
385 * blk_insert_flush - insert a new PREFLUSH/FUA request
386 * @rq: request to insert
387 *
388 * To be called from __elv_add_request() for %ELEVATOR_INSERT_FLUSH insertions.
389 * or __blk_mq_run_hw_queue() to dispatch request.
390 * @rq is being submitted. Analyze what needs to be done and put it on the
391 * right queue.
392 */
393void blk_insert_flush(struct request *rq)
394{
395 struct request_queue *q = rq->q;
396 unsigned long fflags = q->queue_flags; /* may change, cache */
397 unsigned int policy = blk_flush_policy(fflags, rq);
398 struct blk_flush_queue *fq = blk_get_flush_queue(q, rq->mq_ctx);
399
400 /*
401 * @policy now records what operations need to be done. Adjust
402 * REQ_PREFLUSH and FUA for the driver.
403 */
404 rq->cmd_flags &= ~REQ_PREFLUSH;
405 if (!(fflags & (1UL << QUEUE_FLAG_FUA)))
406 rq->cmd_flags &= ~REQ_FUA;
407
408 /*
409 * REQ_PREFLUSH|REQ_FUA implies REQ_SYNC, so if we clear any
410 * of those flags, we have to set REQ_SYNC to avoid skewing
411 * the request accounting.
412 */
413 rq->cmd_flags |= REQ_SYNC;
414
415 /*
416 * An empty flush handed down from a stacking driver may
417 * translate into nothing if the underlying device does not
418 * advertise a write-back cache. In this case, simply
419 * complete the request.
420 */
421 if (!policy) {
422 blk_mq_end_request(rq, 0);
423 return;
424 }
425
426 BUG_ON(rq->bio != rq->biotail); /*assumes zero or single bio rq */
427
428 /*
429 * If there's data but flush is not necessary, the request can be
430 * processed directly without going through flush machinery. Queue
431 * for normal execution.
432 */
433 if ((policy & REQ_FSEQ_DATA) &&
434 !(policy & (REQ_FSEQ_PREFLUSH | REQ_FSEQ_POSTFLUSH))) {
435 blk_mq_request_bypass_insert(rq, false, true);
436 return;
437 }
438
439 /*
440 * @rq should go through flush machinery. Mark it part of flush
441 * sequence and submit for further processing.
442 */
443 memset(&rq->flush, 0, sizeof(rq->flush));
444 INIT_LIST_HEAD(&rq->flush.list);
445 rq->rq_flags |= RQF_FLUSH_SEQ;
446 rq->flush.saved_end_io = rq->end_io; /* Usually NULL */
447
448 rq->end_io = mq_flush_data_end_io;
449
450 spin_lock_irq(&fq->mq_flush_lock);
451 blk_flush_complete_seq(rq, fq, REQ_FSEQ_ACTIONS & ~policy, 0);
452 spin_unlock_irq(&fq->mq_flush_lock);
453}
454
455/**
456 * blkdev_issue_flush - queue a flush
457 * @bdev: blockdev to issue flush for
458 *
459 * Description:
460 * Issue a flush for the block device in question.
461 */
462int blkdev_issue_flush(struct block_device *bdev)
463{
464 struct bio bio;
465
466 bio_init(&bio, bdev, NULL, 0, REQ_OP_WRITE | REQ_PREFLUSH);
467 return submit_bio_wait(&bio);
468}
469EXPORT_SYMBOL(blkdev_issue_flush);
470
471struct blk_flush_queue *blk_alloc_flush_queue(int node, int cmd_size,
472 gfp_t flags)
473{
474 struct blk_flush_queue *fq;
475 int rq_sz = sizeof(struct request);
476
477 fq = kzalloc_node(sizeof(*fq), flags, node);
478 if (!fq)
479 goto fail;
480
481 spin_lock_init(&fq->mq_flush_lock);
482
483 rq_sz = round_up(rq_sz + cmd_size, cache_line_size());
484 fq->flush_rq = kzalloc_node(rq_sz, flags, node);
485 if (!fq->flush_rq)
486 goto fail_rq;
487
488 INIT_LIST_HEAD(&fq->flush_queue[0]);
489 INIT_LIST_HEAD(&fq->flush_queue[1]);
490 INIT_LIST_HEAD(&fq->flush_data_in_flight);
491
492 return fq;
493
494 fail_rq:
495 kfree(fq);
496 fail:
497 return NULL;
498}
499
500void blk_free_flush_queue(struct blk_flush_queue *fq)
501{
502 /* bio based request queue hasn't flush queue */
503 if (!fq)
504 return;
505
506 kfree(fq->flush_rq);
507 kfree(fq);
508}
509
510/*
511 * Allow driver to set its own lock class to fq->mq_flush_lock for
512 * avoiding lockdep complaint.
513 *
514 * flush_end_io() may be called recursively from some driver, such as
515 * nvme-loop, so lockdep may complain 'possible recursive locking' because
516 * all 'struct blk_flush_queue' instance share same mq_flush_lock lock class
517 * key. We need to assign different lock class for these driver's
518 * fq->mq_flush_lock for avoiding the lockdep warning.
519 *
520 * Use dynamically allocated lock class key for each 'blk_flush_queue'
521 * instance is over-kill, and more worse it introduces horrible boot delay
522 * issue because synchronize_rcu() is implied in lockdep_unregister_key which
523 * is called for each hctx release. SCSI probing may synchronously create and
524 * destroy lots of MQ request_queues for non-existent devices, and some robot
525 * test kernel always enable lockdep option. It is observed that more than half
526 * an hour is taken during SCSI MQ probe with per-fq lock class.
527 */
528void blk_mq_hctx_set_fq_lock_class(struct blk_mq_hw_ctx *hctx,
529 struct lock_class_key *key)
530{
531 lockdep_set_class(&hctx->fq->mq_flush_lock, key);
532}
533EXPORT_SYMBOL_GPL(blk_mq_hctx_set_fq_lock_class);
1/*
2 * Functions to sequence FLUSH and FUA writes.
3 *
4 * Copyright (C) 2011 Max Planck Institute for Gravitational Physics
5 * Copyright (C) 2011 Tejun Heo <tj@kernel.org>
6 *
7 * This file is released under the GPLv2.
8 *
9 * REQ_{FLUSH|FUA} requests are decomposed to sequences consisted of three
10 * optional steps - PREFLUSH, DATA and POSTFLUSH - according to the request
11 * properties and hardware capability.
12 *
13 * If a request doesn't have data, only REQ_FLUSH makes sense, which
14 * indicates a simple flush request. If there is data, REQ_FLUSH indicates
15 * that the device cache should be flushed before the data is executed, and
16 * REQ_FUA means that the data must be on non-volatile media on request
17 * completion.
18 *
19 * If the device doesn't have writeback cache, FLUSH and FUA don't make any
20 * difference. The requests are either completed immediately if there's no
21 * data or executed as normal requests otherwise.
22 *
23 * If the device has writeback cache and supports FUA, REQ_FLUSH is
24 * translated to PREFLUSH but REQ_FUA is passed down directly with DATA.
25 *
26 * If the device has writeback cache and doesn't support FUA, REQ_FLUSH is
27 * translated to PREFLUSH and REQ_FUA to POSTFLUSH.
28 *
29 * The actual execution of flush is double buffered. Whenever a request
30 * needs to execute PRE or POSTFLUSH, it queues at
31 * q->flush_queue[q->flush_pending_idx]. Once certain criteria are met, a
32 * flush is issued and the pending_idx is toggled. When the flush
33 * completes, all the requests which were pending are proceeded to the next
34 * step. This allows arbitrary merging of different types of FLUSH/FUA
35 * requests.
36 *
37 * Currently, the following conditions are used to determine when to issue
38 * flush.
39 *
40 * C1. At any given time, only one flush shall be in progress. This makes
41 * double buffering sufficient.
42 *
43 * C2. Flush is deferred if any request is executing DATA of its sequence.
44 * This avoids issuing separate POSTFLUSHes for requests which shared
45 * PREFLUSH.
46 *
47 * C3. The second condition is ignored if there is a request which has
48 * waited longer than FLUSH_PENDING_TIMEOUT. This is to avoid
49 * starvation in the unlikely case where there are continuous stream of
50 * FUA (without FLUSH) requests.
51 *
52 * For devices which support FUA, it isn't clear whether C2 (and thus C3)
53 * is beneficial.
54 *
55 * Note that a sequenced FLUSH/FUA request with DATA is completed twice.
56 * Once while executing DATA and again after the whole sequence is
57 * complete. The first completion updates the contained bio but doesn't
58 * finish it so that the bio submitter is notified only after the whole
59 * sequence is complete. This is implemented by testing REQ_FLUSH_SEQ in
60 * req_bio_endio().
61 *
62 * The above peculiarity requires that each FLUSH/FUA request has only one
63 * bio attached to it, which is guaranteed as they aren't allowed to be
64 * merged in the usual way.
65 */
66
67#include <linux/kernel.h>
68#include <linux/module.h>
69#include <linux/bio.h>
70#include <linux/blkdev.h>
71#include <linux/gfp.h>
72
73#include "blk.h"
74
75/* FLUSH/FUA sequences */
76enum {
77 REQ_FSEQ_PREFLUSH = (1 << 0), /* pre-flushing in progress */
78 REQ_FSEQ_DATA = (1 << 1), /* data write in progress */
79 REQ_FSEQ_POSTFLUSH = (1 << 2), /* post-flushing in progress */
80 REQ_FSEQ_DONE = (1 << 3),
81
82 REQ_FSEQ_ACTIONS = REQ_FSEQ_PREFLUSH | REQ_FSEQ_DATA |
83 REQ_FSEQ_POSTFLUSH,
84
85 /*
86 * If flush has been pending longer than the following timeout,
87 * it's issued even if flush_data requests are still in flight.
88 */
89 FLUSH_PENDING_TIMEOUT = 5 * HZ,
90};
91
92static bool blk_kick_flush(struct request_queue *q);
93
94static unsigned int blk_flush_policy(unsigned int fflags, struct request *rq)
95{
96 unsigned int policy = 0;
97
98 if (blk_rq_sectors(rq))
99 policy |= REQ_FSEQ_DATA;
100
101 if (fflags & REQ_FLUSH) {
102 if (rq->cmd_flags & REQ_FLUSH)
103 policy |= REQ_FSEQ_PREFLUSH;
104 if (!(fflags & REQ_FUA) && (rq->cmd_flags & REQ_FUA))
105 policy |= REQ_FSEQ_POSTFLUSH;
106 }
107 return policy;
108}
109
110static unsigned int blk_flush_cur_seq(struct request *rq)
111{
112 return 1 << ffz(rq->flush.seq);
113}
114
115static void blk_flush_restore_request(struct request *rq)
116{
117 /*
118 * After flush data completion, @rq->bio is %NULL but we need to
119 * complete the bio again. @rq->biotail is guaranteed to equal the
120 * original @rq->bio. Restore it.
121 */
122 rq->bio = rq->biotail;
123
124 /* make @rq a normal request */
125 rq->cmd_flags &= ~REQ_FLUSH_SEQ;
126 rq->end_io = rq->flush.saved_end_io;
127}
128
129/**
130 * blk_flush_complete_seq - complete flush sequence
131 * @rq: FLUSH/FUA request being sequenced
132 * @seq: sequences to complete (mask of %REQ_FSEQ_*, can be zero)
133 * @error: whether an error occurred
134 *
135 * @rq just completed @seq part of its flush sequence, record the
136 * completion and trigger the next step.
137 *
138 * CONTEXT:
139 * spin_lock_irq(q->queue_lock)
140 *
141 * RETURNS:
142 * %true if requests were added to the dispatch queue, %false otherwise.
143 */
144static bool blk_flush_complete_seq(struct request *rq, unsigned int seq,
145 int error)
146{
147 struct request_queue *q = rq->q;
148 struct list_head *pending = &q->flush_queue[q->flush_pending_idx];
149 bool queued = false;
150
151 BUG_ON(rq->flush.seq & seq);
152 rq->flush.seq |= seq;
153
154 if (likely(!error))
155 seq = blk_flush_cur_seq(rq);
156 else
157 seq = REQ_FSEQ_DONE;
158
159 switch (seq) {
160 case REQ_FSEQ_PREFLUSH:
161 case REQ_FSEQ_POSTFLUSH:
162 /* queue for flush */
163 if (list_empty(pending))
164 q->flush_pending_since = jiffies;
165 list_move_tail(&rq->flush.list, pending);
166 break;
167
168 case REQ_FSEQ_DATA:
169 list_move_tail(&rq->flush.list, &q->flush_data_in_flight);
170 list_add(&rq->queuelist, &q->queue_head);
171 queued = true;
172 break;
173
174 case REQ_FSEQ_DONE:
175 /*
176 * @rq was previously adjusted by blk_flush_issue() for
177 * flush sequencing and may already have gone through the
178 * flush data request completion path. Restore @rq for
179 * normal completion and end it.
180 */
181 BUG_ON(!list_empty(&rq->queuelist));
182 list_del_init(&rq->flush.list);
183 blk_flush_restore_request(rq);
184 __blk_end_request_all(rq, error);
185 break;
186
187 default:
188 BUG();
189 }
190
191 return blk_kick_flush(q) | queued;
192}
193
194static void flush_end_io(struct request *flush_rq, int error)
195{
196 struct request_queue *q = flush_rq->q;
197 struct list_head *running = &q->flush_queue[q->flush_running_idx];
198 bool queued = false;
199 struct request *rq, *n;
200
201 BUG_ON(q->flush_pending_idx == q->flush_running_idx);
202
203 /* account completion of the flush request */
204 q->flush_running_idx ^= 1;
205 elv_completed_request(q, flush_rq);
206
207 /* and push the waiting requests to the next stage */
208 list_for_each_entry_safe(rq, n, running, flush.list) {
209 unsigned int seq = blk_flush_cur_seq(rq);
210
211 BUG_ON(seq != REQ_FSEQ_PREFLUSH && seq != REQ_FSEQ_POSTFLUSH);
212 queued |= blk_flush_complete_seq(rq, seq, error);
213 }
214
215 /*
216 * Kick the queue to avoid stall for two cases:
217 * 1. Moving a request silently to empty queue_head may stall the
218 * queue.
219 * 2. When flush request is running in non-queueable queue, the
220 * queue is hold. Restart the queue after flush request is finished
221 * to avoid stall.
222 * This function is called from request completion path and calling
223 * directly into request_fn may confuse the driver. Always use
224 * kblockd.
225 */
226 if (queued || q->flush_queue_delayed)
227 blk_run_queue_async(q);
228 q->flush_queue_delayed = 0;
229}
230
231/**
232 * blk_kick_flush - consider issuing flush request
233 * @q: request_queue being kicked
234 *
235 * Flush related states of @q have changed, consider issuing flush request.
236 * Please read the comment at the top of this file for more info.
237 *
238 * CONTEXT:
239 * spin_lock_irq(q->queue_lock)
240 *
241 * RETURNS:
242 * %true if flush was issued, %false otherwise.
243 */
244static bool blk_kick_flush(struct request_queue *q)
245{
246 struct list_head *pending = &q->flush_queue[q->flush_pending_idx];
247 struct request *first_rq =
248 list_first_entry(pending, struct request, flush.list);
249
250 /* C1 described at the top of this file */
251 if (q->flush_pending_idx != q->flush_running_idx || list_empty(pending))
252 return false;
253
254 /* C2 and C3 */
255 if (!list_empty(&q->flush_data_in_flight) &&
256 time_before(jiffies,
257 q->flush_pending_since + FLUSH_PENDING_TIMEOUT))
258 return false;
259
260 /*
261 * Issue flush and toggle pending_idx. This makes pending_idx
262 * different from running_idx, which means flush is in flight.
263 */
264 blk_rq_init(q, &q->flush_rq);
265 q->flush_rq.cmd_type = REQ_TYPE_FS;
266 q->flush_rq.cmd_flags = WRITE_FLUSH | REQ_FLUSH_SEQ;
267 q->flush_rq.rq_disk = first_rq->rq_disk;
268 q->flush_rq.end_io = flush_end_io;
269
270 q->flush_pending_idx ^= 1;
271 list_add_tail(&q->flush_rq.queuelist, &q->queue_head);
272 return true;
273}
274
275static void flush_data_end_io(struct request *rq, int error)
276{
277 struct request_queue *q = rq->q;
278
279 /*
280 * After populating an empty queue, kick it to avoid stall. Read
281 * the comment in flush_end_io().
282 */
283 if (blk_flush_complete_seq(rq, REQ_FSEQ_DATA, error))
284 blk_run_queue_async(q);
285}
286
287/**
288 * blk_insert_flush - insert a new FLUSH/FUA request
289 * @rq: request to insert
290 *
291 * To be called from __elv_add_request() for %ELEVATOR_INSERT_FLUSH insertions.
292 * @rq is being submitted. Analyze what needs to be done and put it on the
293 * right queue.
294 *
295 * CONTEXT:
296 * spin_lock_irq(q->queue_lock)
297 */
298void blk_insert_flush(struct request *rq)
299{
300 struct request_queue *q = rq->q;
301 unsigned int fflags = q->flush_flags; /* may change, cache */
302 unsigned int policy = blk_flush_policy(fflags, rq);
303
304 /*
305 * @policy now records what operations need to be done. Adjust
306 * REQ_FLUSH and FUA for the driver.
307 */
308 rq->cmd_flags &= ~REQ_FLUSH;
309 if (!(fflags & REQ_FUA))
310 rq->cmd_flags &= ~REQ_FUA;
311
312 /*
313 * An empty flush handed down from a stacking driver may
314 * translate into nothing if the underlying device does not
315 * advertise a write-back cache. In this case, simply
316 * complete the request.
317 */
318 if (!policy) {
319 __blk_end_bidi_request(rq, 0, 0, 0);
320 return;
321 }
322
323 BUG_ON(rq->bio != rq->biotail); /*assumes zero or single bio rq */
324
325 /*
326 * If there's data but flush is not necessary, the request can be
327 * processed directly without going through flush machinery. Queue
328 * for normal execution.
329 */
330 if ((policy & REQ_FSEQ_DATA) &&
331 !(policy & (REQ_FSEQ_PREFLUSH | REQ_FSEQ_POSTFLUSH))) {
332 list_add_tail(&rq->queuelist, &q->queue_head);
333 return;
334 }
335
336 /*
337 * @rq should go through flush machinery. Mark it part of flush
338 * sequence and submit for further processing.
339 */
340 memset(&rq->flush, 0, sizeof(rq->flush));
341 INIT_LIST_HEAD(&rq->flush.list);
342 rq->cmd_flags |= REQ_FLUSH_SEQ;
343 rq->flush.saved_end_io = rq->end_io; /* Usually NULL */
344 rq->end_io = flush_data_end_io;
345
346 blk_flush_complete_seq(rq, REQ_FSEQ_ACTIONS & ~policy, 0);
347}
348
349/**
350 * blk_abort_flushes - @q is being aborted, abort flush requests
351 * @q: request_queue being aborted
352 *
353 * To be called from elv_abort_queue(). @q is being aborted. Prepare all
354 * FLUSH/FUA requests for abortion.
355 *
356 * CONTEXT:
357 * spin_lock_irq(q->queue_lock)
358 */
359void blk_abort_flushes(struct request_queue *q)
360{
361 struct request *rq, *n;
362 int i;
363
364 /*
365 * Requests in flight for data are already owned by the dispatch
366 * queue or the device driver. Just restore for normal completion.
367 */
368 list_for_each_entry_safe(rq, n, &q->flush_data_in_flight, flush.list) {
369 list_del_init(&rq->flush.list);
370 blk_flush_restore_request(rq);
371 }
372
373 /*
374 * We need to give away requests on flush queues. Restore for
375 * normal completion and put them on the dispatch queue.
376 */
377 for (i = 0; i < ARRAY_SIZE(q->flush_queue); i++) {
378 list_for_each_entry_safe(rq, n, &q->flush_queue[i],
379 flush.list) {
380 list_del_init(&rq->flush.list);
381 blk_flush_restore_request(rq);
382 list_add_tail(&rq->queuelist, &q->queue_head);
383 }
384 }
385}
386
387static void bio_end_flush(struct bio *bio, int err)
388{
389 if (err)
390 clear_bit(BIO_UPTODATE, &bio->bi_flags);
391 if (bio->bi_private)
392 complete(bio->bi_private);
393 bio_put(bio);
394}
395
396/**
397 * blkdev_issue_flush - queue a flush
398 * @bdev: blockdev to issue flush for
399 * @gfp_mask: memory allocation flags (for bio_alloc)
400 * @error_sector: error sector
401 *
402 * Description:
403 * Issue a flush for the block device in question. Caller can supply
404 * room for storing the error offset in case of a flush error, if they
405 * wish to. If WAIT flag is not passed then caller may check only what
406 * request was pushed in some internal queue for later handling.
407 */
408int blkdev_issue_flush(struct block_device *bdev, gfp_t gfp_mask,
409 sector_t *error_sector)
410{
411 DECLARE_COMPLETION_ONSTACK(wait);
412 struct request_queue *q;
413 struct bio *bio;
414 int ret = 0;
415
416 if (bdev->bd_disk == NULL)
417 return -ENXIO;
418
419 q = bdev_get_queue(bdev);
420 if (!q)
421 return -ENXIO;
422
423 /*
424 * some block devices may not have their queue correctly set up here
425 * (e.g. loop device without a backing file) and so issuing a flush
426 * here will panic. Ensure there is a request function before issuing
427 * the flush.
428 */
429 if (!q->make_request_fn)
430 return -ENXIO;
431
432 bio = bio_alloc(gfp_mask, 0);
433 bio->bi_end_io = bio_end_flush;
434 bio->bi_bdev = bdev;
435 bio->bi_private = &wait;
436
437 bio_get(bio);
438 submit_bio(WRITE_FLUSH, bio);
439 wait_for_completion(&wait);
440
441 /*
442 * The driver must store the error location in ->bi_sector, if
443 * it supports it. For non-stacked drivers, this should be
444 * copied from blk_rq_pos(rq).
445 */
446 if (error_sector)
447 *error_sector = bio->bi_sector;
448
449 if (!bio_flagged(bio, BIO_UPTODATE))
450 ret = -EIO;
451
452 bio_put(bio);
453 return ret;
454}
455EXPORT_SYMBOL(blkdev_issue_flush);