Loading...
1/*
2 * Driver for AMBA serial ports
3 *
4 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
5 *
6 * Copyright 1999 ARM Limited
7 * Copyright (C) 2000 Deep Blue Solutions Ltd.
8 * Copyright (C) 2010 ST-Ericsson SA
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; either version 2 of the License, or
13 * (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 *
24 * This is a generic driver for ARM AMBA-type serial ports. They
25 * have a lot of 16550-like features, but are not register compatible.
26 * Note that although they do have CTS, DCD and DSR inputs, they do
27 * not have an RI input, nor do they have DTR or RTS outputs. If
28 * required, these have to be supplied via some other means (eg, GPIO)
29 * and hooked into this driver.
30 */
31
32#if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
33#define SUPPORT_SYSRQ
34#endif
35
36#include <linux/module.h>
37#include <linux/ioport.h>
38#include <linux/init.h>
39#include <linux/console.h>
40#include <linux/sysrq.h>
41#include <linux/device.h>
42#include <linux/tty.h>
43#include <linux/tty_flip.h>
44#include <linux/serial_core.h>
45#include <linux/serial.h>
46#include <linux/amba/bus.h>
47#include <linux/amba/serial.h>
48#include <linux/clk.h>
49#include <linux/slab.h>
50#include <linux/dmaengine.h>
51#include <linux/dma-mapping.h>
52#include <linux/scatterlist.h>
53#include <linux/delay.h>
54
55#include <asm/io.h>
56#include <asm/sizes.h>
57
58#define UART_NR 14
59
60#define SERIAL_AMBA_MAJOR 204
61#define SERIAL_AMBA_MINOR 64
62#define SERIAL_AMBA_NR UART_NR
63
64#define AMBA_ISR_PASS_LIMIT 256
65
66#define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE)
67#define UART_DUMMY_DR_RX (1 << 16)
68
69
70#define UART_WA_SAVE_NR 14
71
72static void pl011_lockup_wa(unsigned long data);
73static const u32 uart_wa_reg[UART_WA_SAVE_NR] = {
74 ST_UART011_DMAWM,
75 ST_UART011_TIMEOUT,
76 ST_UART011_LCRH_RX,
77 UART011_IBRD,
78 UART011_FBRD,
79 ST_UART011_LCRH_TX,
80 UART011_IFLS,
81 ST_UART011_XFCR,
82 ST_UART011_XON1,
83 ST_UART011_XON2,
84 ST_UART011_XOFF1,
85 ST_UART011_XOFF2,
86 UART011_CR,
87 UART011_IMSC
88};
89
90static u32 uart_wa_regdata[UART_WA_SAVE_NR];
91static DECLARE_TASKLET(pl011_lockup_tlet, pl011_lockup_wa, 0);
92
93/* There is by now at least one vendor with differing details, so handle it */
94struct vendor_data {
95 unsigned int ifls;
96 unsigned int fifosize;
97 unsigned int lcrh_tx;
98 unsigned int lcrh_rx;
99 bool oversampling;
100 bool interrupt_may_hang; /* vendor-specific */
101 bool dma_threshold;
102};
103
104static struct vendor_data vendor_arm = {
105 .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
106 .fifosize = 16,
107 .lcrh_tx = UART011_LCRH,
108 .lcrh_rx = UART011_LCRH,
109 .oversampling = false,
110 .dma_threshold = false,
111};
112
113static struct vendor_data vendor_st = {
114 .ifls = UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF,
115 .fifosize = 64,
116 .lcrh_tx = ST_UART011_LCRH_TX,
117 .lcrh_rx = ST_UART011_LCRH_RX,
118 .oversampling = true,
119 .interrupt_may_hang = true,
120 .dma_threshold = true,
121};
122
123static struct uart_amba_port *amba_ports[UART_NR];
124
125/* Deals with DMA transactions */
126
127struct pl011_sgbuf {
128 struct scatterlist sg;
129 char *buf;
130};
131
132struct pl011_dmarx_data {
133 struct dma_chan *chan;
134 struct completion complete;
135 bool use_buf_b;
136 struct pl011_sgbuf sgbuf_a;
137 struct pl011_sgbuf sgbuf_b;
138 dma_cookie_t cookie;
139 bool running;
140};
141
142struct pl011_dmatx_data {
143 struct dma_chan *chan;
144 struct scatterlist sg;
145 char *buf;
146 bool queued;
147};
148
149/*
150 * We wrap our port structure around the generic uart_port.
151 */
152struct uart_amba_port {
153 struct uart_port port;
154 struct clk *clk;
155 const struct vendor_data *vendor;
156 unsigned int dmacr; /* dma control reg */
157 unsigned int im; /* interrupt mask */
158 unsigned int old_status;
159 unsigned int fifosize; /* vendor-specific */
160 unsigned int lcrh_tx; /* vendor-specific */
161 unsigned int lcrh_rx; /* vendor-specific */
162 bool autorts;
163 char type[12];
164 bool interrupt_may_hang; /* vendor-specific */
165#ifdef CONFIG_DMA_ENGINE
166 /* DMA stuff */
167 bool using_tx_dma;
168 bool using_rx_dma;
169 struct pl011_dmarx_data dmarx;
170 struct pl011_dmatx_data dmatx;
171#endif
172};
173
174/*
175 * Reads up to 256 characters from the FIFO or until it's empty and
176 * inserts them into the TTY layer. Returns the number of characters
177 * read from the FIFO.
178 */
179static int pl011_fifo_to_tty(struct uart_amba_port *uap)
180{
181 u16 status, ch;
182 unsigned int flag, max_count = 256;
183 int fifotaken = 0;
184
185 while (max_count--) {
186 status = readw(uap->port.membase + UART01x_FR);
187 if (status & UART01x_FR_RXFE)
188 break;
189
190 /* Take chars from the FIFO and update status */
191 ch = readw(uap->port.membase + UART01x_DR) |
192 UART_DUMMY_DR_RX;
193 flag = TTY_NORMAL;
194 uap->port.icount.rx++;
195 fifotaken++;
196
197 if (unlikely(ch & UART_DR_ERROR)) {
198 if (ch & UART011_DR_BE) {
199 ch &= ~(UART011_DR_FE | UART011_DR_PE);
200 uap->port.icount.brk++;
201 if (uart_handle_break(&uap->port))
202 continue;
203 } else if (ch & UART011_DR_PE)
204 uap->port.icount.parity++;
205 else if (ch & UART011_DR_FE)
206 uap->port.icount.frame++;
207 if (ch & UART011_DR_OE)
208 uap->port.icount.overrun++;
209
210 ch &= uap->port.read_status_mask;
211
212 if (ch & UART011_DR_BE)
213 flag = TTY_BREAK;
214 else if (ch & UART011_DR_PE)
215 flag = TTY_PARITY;
216 else if (ch & UART011_DR_FE)
217 flag = TTY_FRAME;
218 }
219
220 if (uart_handle_sysrq_char(&uap->port, ch & 255))
221 continue;
222
223 uart_insert_char(&uap->port, ch, UART011_DR_OE, ch, flag);
224 }
225
226 return fifotaken;
227}
228
229
230/*
231 * All the DMA operation mode stuff goes inside this ifdef.
232 * This assumes that you have a generic DMA device interface,
233 * no custom DMA interfaces are supported.
234 */
235#ifdef CONFIG_DMA_ENGINE
236
237#define PL011_DMA_BUFFER_SIZE PAGE_SIZE
238
239static int pl011_sgbuf_init(struct dma_chan *chan, struct pl011_sgbuf *sg,
240 enum dma_data_direction dir)
241{
242 sg->buf = kmalloc(PL011_DMA_BUFFER_SIZE, GFP_KERNEL);
243 if (!sg->buf)
244 return -ENOMEM;
245
246 sg_init_one(&sg->sg, sg->buf, PL011_DMA_BUFFER_SIZE);
247
248 if (dma_map_sg(chan->device->dev, &sg->sg, 1, dir) != 1) {
249 kfree(sg->buf);
250 return -EINVAL;
251 }
252 return 0;
253}
254
255static void pl011_sgbuf_free(struct dma_chan *chan, struct pl011_sgbuf *sg,
256 enum dma_data_direction dir)
257{
258 if (sg->buf) {
259 dma_unmap_sg(chan->device->dev, &sg->sg, 1, dir);
260 kfree(sg->buf);
261 }
262}
263
264static void pl011_dma_probe_initcall(struct uart_amba_port *uap)
265{
266 /* DMA is the sole user of the platform data right now */
267 struct amba_pl011_data *plat = uap->port.dev->platform_data;
268 struct dma_slave_config tx_conf = {
269 .dst_addr = uap->port.mapbase + UART01x_DR,
270 .dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
271 .direction = DMA_TO_DEVICE,
272 .dst_maxburst = uap->fifosize >> 1,
273 };
274 struct dma_chan *chan;
275 dma_cap_mask_t mask;
276
277 /* We need platform data */
278 if (!plat || !plat->dma_filter) {
279 dev_info(uap->port.dev, "no DMA platform data\n");
280 return;
281 }
282
283 /* Try to acquire a generic DMA engine slave TX channel */
284 dma_cap_zero(mask);
285 dma_cap_set(DMA_SLAVE, mask);
286
287 chan = dma_request_channel(mask, plat->dma_filter, plat->dma_tx_param);
288 if (!chan) {
289 dev_err(uap->port.dev, "no TX DMA channel!\n");
290 return;
291 }
292
293 dmaengine_slave_config(chan, &tx_conf);
294 uap->dmatx.chan = chan;
295
296 dev_info(uap->port.dev, "DMA channel TX %s\n",
297 dma_chan_name(uap->dmatx.chan));
298
299 /* Optionally make use of an RX channel as well */
300 if (plat->dma_rx_param) {
301 struct dma_slave_config rx_conf = {
302 .src_addr = uap->port.mapbase + UART01x_DR,
303 .src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
304 .direction = DMA_FROM_DEVICE,
305 .src_maxburst = uap->fifosize >> 1,
306 };
307
308 chan = dma_request_channel(mask, plat->dma_filter, plat->dma_rx_param);
309 if (!chan) {
310 dev_err(uap->port.dev, "no RX DMA channel!\n");
311 return;
312 }
313
314 dmaengine_slave_config(chan, &rx_conf);
315 uap->dmarx.chan = chan;
316
317 dev_info(uap->port.dev, "DMA channel RX %s\n",
318 dma_chan_name(uap->dmarx.chan));
319 }
320}
321
322#ifndef MODULE
323/*
324 * Stack up the UARTs and let the above initcall be done at device
325 * initcall time, because the serial driver is called as an arch
326 * initcall, and at this time the DMA subsystem is not yet registered.
327 * At this point the driver will switch over to using DMA where desired.
328 */
329struct dma_uap {
330 struct list_head node;
331 struct uart_amba_port *uap;
332};
333
334static LIST_HEAD(pl011_dma_uarts);
335
336static int __init pl011_dma_initcall(void)
337{
338 struct list_head *node, *tmp;
339
340 list_for_each_safe(node, tmp, &pl011_dma_uarts) {
341 struct dma_uap *dmau = list_entry(node, struct dma_uap, node);
342 pl011_dma_probe_initcall(dmau->uap);
343 list_del(node);
344 kfree(dmau);
345 }
346 return 0;
347}
348
349device_initcall(pl011_dma_initcall);
350
351static void pl011_dma_probe(struct uart_amba_port *uap)
352{
353 struct dma_uap *dmau = kzalloc(sizeof(struct dma_uap), GFP_KERNEL);
354 if (dmau) {
355 dmau->uap = uap;
356 list_add_tail(&dmau->node, &pl011_dma_uarts);
357 }
358}
359#else
360static void pl011_dma_probe(struct uart_amba_port *uap)
361{
362 pl011_dma_probe_initcall(uap);
363}
364#endif
365
366static void pl011_dma_remove(struct uart_amba_port *uap)
367{
368 /* TODO: remove the initcall if it has not yet executed */
369 if (uap->dmatx.chan)
370 dma_release_channel(uap->dmatx.chan);
371 if (uap->dmarx.chan)
372 dma_release_channel(uap->dmarx.chan);
373}
374
375/* Forward declare this for the refill routine */
376static int pl011_dma_tx_refill(struct uart_amba_port *uap);
377
378/*
379 * The current DMA TX buffer has been sent.
380 * Try to queue up another DMA buffer.
381 */
382static void pl011_dma_tx_callback(void *data)
383{
384 struct uart_amba_port *uap = data;
385 struct pl011_dmatx_data *dmatx = &uap->dmatx;
386 unsigned long flags;
387 u16 dmacr;
388
389 spin_lock_irqsave(&uap->port.lock, flags);
390 if (uap->dmatx.queued)
391 dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1,
392 DMA_TO_DEVICE);
393
394 dmacr = uap->dmacr;
395 uap->dmacr = dmacr & ~UART011_TXDMAE;
396 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
397
398 /*
399 * If TX DMA was disabled, it means that we've stopped the DMA for
400 * some reason (eg, XOFF received, or we want to send an X-char.)
401 *
402 * Note: we need to be careful here of a potential race between DMA
403 * and the rest of the driver - if the driver disables TX DMA while
404 * a TX buffer completing, we must update the tx queued status to
405 * get further refills (hence we check dmacr).
406 */
407 if (!(dmacr & UART011_TXDMAE) || uart_tx_stopped(&uap->port) ||
408 uart_circ_empty(&uap->port.state->xmit)) {
409 uap->dmatx.queued = false;
410 spin_unlock_irqrestore(&uap->port.lock, flags);
411 return;
412 }
413
414 if (pl011_dma_tx_refill(uap) <= 0) {
415 /*
416 * We didn't queue a DMA buffer for some reason, but we
417 * have data pending to be sent. Re-enable the TX IRQ.
418 */
419 uap->im |= UART011_TXIM;
420 writew(uap->im, uap->port.membase + UART011_IMSC);
421 }
422 spin_unlock_irqrestore(&uap->port.lock, flags);
423}
424
425/*
426 * Try to refill the TX DMA buffer.
427 * Locking: called with port lock held and IRQs disabled.
428 * Returns:
429 * 1 if we queued up a TX DMA buffer.
430 * 0 if we didn't want to handle this by DMA
431 * <0 on error
432 */
433static int pl011_dma_tx_refill(struct uart_amba_port *uap)
434{
435 struct pl011_dmatx_data *dmatx = &uap->dmatx;
436 struct dma_chan *chan = dmatx->chan;
437 struct dma_device *dma_dev = chan->device;
438 struct dma_async_tx_descriptor *desc;
439 struct circ_buf *xmit = &uap->port.state->xmit;
440 unsigned int count;
441
442 /*
443 * Try to avoid the overhead involved in using DMA if the
444 * transaction fits in the first half of the FIFO, by using
445 * the standard interrupt handling. This ensures that we
446 * issue a uart_write_wakeup() at the appropriate time.
447 */
448 count = uart_circ_chars_pending(xmit);
449 if (count < (uap->fifosize >> 1)) {
450 uap->dmatx.queued = false;
451 return 0;
452 }
453
454 /*
455 * Bodge: don't send the last character by DMA, as this
456 * will prevent XON from notifying us to restart DMA.
457 */
458 count -= 1;
459
460 /* Else proceed to copy the TX chars to the DMA buffer and fire DMA */
461 if (count > PL011_DMA_BUFFER_SIZE)
462 count = PL011_DMA_BUFFER_SIZE;
463
464 if (xmit->tail < xmit->head)
465 memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], count);
466 else {
467 size_t first = UART_XMIT_SIZE - xmit->tail;
468 size_t second = xmit->head;
469
470 memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], first);
471 if (second)
472 memcpy(&dmatx->buf[first], &xmit->buf[0], second);
473 }
474
475 dmatx->sg.length = count;
476
477 if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) {
478 uap->dmatx.queued = false;
479 dev_dbg(uap->port.dev, "unable to map TX DMA\n");
480 return -EBUSY;
481 }
482
483 desc = dma_dev->device_prep_slave_sg(chan, &dmatx->sg, 1, DMA_TO_DEVICE,
484 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
485 if (!desc) {
486 dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE);
487 uap->dmatx.queued = false;
488 /*
489 * If DMA cannot be used right now, we complete this
490 * transaction via IRQ and let the TTY layer retry.
491 */
492 dev_dbg(uap->port.dev, "TX DMA busy\n");
493 return -EBUSY;
494 }
495
496 /* Some data to go along to the callback */
497 desc->callback = pl011_dma_tx_callback;
498 desc->callback_param = uap;
499
500 /* All errors should happen at prepare time */
501 dmaengine_submit(desc);
502
503 /* Fire the DMA transaction */
504 dma_dev->device_issue_pending(chan);
505
506 uap->dmacr |= UART011_TXDMAE;
507 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
508 uap->dmatx.queued = true;
509
510 /*
511 * Now we know that DMA will fire, so advance the ring buffer
512 * with the stuff we just dispatched.
513 */
514 xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
515 uap->port.icount.tx += count;
516
517 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
518 uart_write_wakeup(&uap->port);
519
520 return 1;
521}
522
523/*
524 * We received a transmit interrupt without a pending X-char but with
525 * pending characters.
526 * Locking: called with port lock held and IRQs disabled.
527 * Returns:
528 * false if we want to use PIO to transmit
529 * true if we queued a DMA buffer
530 */
531static bool pl011_dma_tx_irq(struct uart_amba_port *uap)
532{
533 if (!uap->using_tx_dma)
534 return false;
535
536 /*
537 * If we already have a TX buffer queued, but received a
538 * TX interrupt, it will be because we've just sent an X-char.
539 * Ensure the TX DMA is enabled and the TX IRQ is disabled.
540 */
541 if (uap->dmatx.queued) {
542 uap->dmacr |= UART011_TXDMAE;
543 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
544 uap->im &= ~UART011_TXIM;
545 writew(uap->im, uap->port.membase + UART011_IMSC);
546 return true;
547 }
548
549 /*
550 * We don't have a TX buffer queued, so try to queue one.
551 * If we successfully queued a buffer, mask the TX IRQ.
552 */
553 if (pl011_dma_tx_refill(uap) > 0) {
554 uap->im &= ~UART011_TXIM;
555 writew(uap->im, uap->port.membase + UART011_IMSC);
556 return true;
557 }
558 return false;
559}
560
561/*
562 * Stop the DMA transmit (eg, due to received XOFF).
563 * Locking: called with port lock held and IRQs disabled.
564 */
565static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
566{
567 if (uap->dmatx.queued) {
568 uap->dmacr &= ~UART011_TXDMAE;
569 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
570 }
571}
572
573/*
574 * Try to start a DMA transmit, or in the case of an XON/OFF
575 * character queued for send, try to get that character out ASAP.
576 * Locking: called with port lock held and IRQs disabled.
577 * Returns:
578 * false if we want the TX IRQ to be enabled
579 * true if we have a buffer queued
580 */
581static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
582{
583 u16 dmacr;
584
585 if (!uap->using_tx_dma)
586 return false;
587
588 if (!uap->port.x_char) {
589 /* no X-char, try to push chars out in DMA mode */
590 bool ret = true;
591
592 if (!uap->dmatx.queued) {
593 if (pl011_dma_tx_refill(uap) > 0) {
594 uap->im &= ~UART011_TXIM;
595 ret = true;
596 } else {
597 uap->im |= UART011_TXIM;
598 ret = false;
599 }
600 writew(uap->im, uap->port.membase + UART011_IMSC);
601 } else if (!(uap->dmacr & UART011_TXDMAE)) {
602 uap->dmacr |= UART011_TXDMAE;
603 writew(uap->dmacr,
604 uap->port.membase + UART011_DMACR);
605 }
606 return ret;
607 }
608
609 /*
610 * We have an X-char to send. Disable DMA to prevent it loading
611 * the TX fifo, and then see if we can stuff it into the FIFO.
612 */
613 dmacr = uap->dmacr;
614 uap->dmacr &= ~UART011_TXDMAE;
615 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
616
617 if (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF) {
618 /*
619 * No space in the FIFO, so enable the transmit interrupt
620 * so we know when there is space. Note that once we've
621 * loaded the character, we should just re-enable DMA.
622 */
623 return false;
624 }
625
626 writew(uap->port.x_char, uap->port.membase + UART01x_DR);
627 uap->port.icount.tx++;
628 uap->port.x_char = 0;
629
630 /* Success - restore the DMA state */
631 uap->dmacr = dmacr;
632 writew(dmacr, uap->port.membase + UART011_DMACR);
633
634 return true;
635}
636
637/*
638 * Flush the transmit buffer.
639 * Locking: called with port lock held and IRQs disabled.
640 */
641static void pl011_dma_flush_buffer(struct uart_port *port)
642{
643 struct uart_amba_port *uap = (struct uart_amba_port *)port;
644
645 if (!uap->using_tx_dma)
646 return;
647
648 /* Avoid deadlock with the DMA engine callback */
649 spin_unlock(&uap->port.lock);
650 dmaengine_terminate_all(uap->dmatx.chan);
651 spin_lock(&uap->port.lock);
652 if (uap->dmatx.queued) {
653 dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
654 DMA_TO_DEVICE);
655 uap->dmatx.queued = false;
656 uap->dmacr &= ~UART011_TXDMAE;
657 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
658 }
659}
660
661static void pl011_dma_rx_callback(void *data);
662
663static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
664{
665 struct dma_chan *rxchan = uap->dmarx.chan;
666 struct dma_device *dma_dev;
667 struct pl011_dmarx_data *dmarx = &uap->dmarx;
668 struct dma_async_tx_descriptor *desc;
669 struct pl011_sgbuf *sgbuf;
670
671 if (!rxchan)
672 return -EIO;
673
674 /* Start the RX DMA job */
675 sgbuf = uap->dmarx.use_buf_b ?
676 &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
677 dma_dev = rxchan->device;
678 desc = rxchan->device->device_prep_slave_sg(rxchan, &sgbuf->sg, 1,
679 DMA_FROM_DEVICE,
680 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
681 /*
682 * If the DMA engine is busy and cannot prepare a
683 * channel, no big deal, the driver will fall back
684 * to interrupt mode as a result of this error code.
685 */
686 if (!desc) {
687 uap->dmarx.running = false;
688 dmaengine_terminate_all(rxchan);
689 return -EBUSY;
690 }
691
692 /* Some data to go along to the callback */
693 desc->callback = pl011_dma_rx_callback;
694 desc->callback_param = uap;
695 dmarx->cookie = dmaengine_submit(desc);
696 dma_async_issue_pending(rxchan);
697
698 uap->dmacr |= UART011_RXDMAE;
699 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
700 uap->dmarx.running = true;
701
702 uap->im &= ~UART011_RXIM;
703 writew(uap->im, uap->port.membase + UART011_IMSC);
704
705 return 0;
706}
707
708/*
709 * This is called when either the DMA job is complete, or
710 * the FIFO timeout interrupt occurred. This must be called
711 * with the port spinlock uap->port.lock held.
712 */
713static void pl011_dma_rx_chars(struct uart_amba_port *uap,
714 u32 pending, bool use_buf_b,
715 bool readfifo)
716{
717 struct tty_struct *tty = uap->port.state->port.tty;
718 struct pl011_sgbuf *sgbuf = use_buf_b ?
719 &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
720 struct device *dev = uap->dmarx.chan->device->dev;
721 int dma_count = 0;
722 u32 fifotaken = 0; /* only used for vdbg() */
723
724 /* Pick everything from the DMA first */
725 if (pending) {
726 /* Sync in buffer */
727 dma_sync_sg_for_cpu(dev, &sgbuf->sg, 1, DMA_FROM_DEVICE);
728
729 /*
730 * First take all chars in the DMA pipe, then look in the FIFO.
731 * Note that tty_insert_flip_buf() tries to take as many chars
732 * as it can.
733 */
734 dma_count = tty_insert_flip_string(uap->port.state->port.tty,
735 sgbuf->buf, pending);
736
737 /* Return buffer to device */
738 dma_sync_sg_for_device(dev, &sgbuf->sg, 1, DMA_FROM_DEVICE);
739
740 uap->port.icount.rx += dma_count;
741 if (dma_count < pending)
742 dev_warn(uap->port.dev,
743 "couldn't insert all characters (TTY is full?)\n");
744 }
745
746 /*
747 * Only continue with trying to read the FIFO if all DMA chars have
748 * been taken first.
749 */
750 if (dma_count == pending && readfifo) {
751 /* Clear any error flags */
752 writew(UART011_OEIS | UART011_BEIS | UART011_PEIS | UART011_FEIS,
753 uap->port.membase + UART011_ICR);
754
755 /*
756 * If we read all the DMA'd characters, and we had an
757 * incomplete buffer, that could be due to an rx error, or
758 * maybe we just timed out. Read any pending chars and check
759 * the error status.
760 *
761 * Error conditions will only occur in the FIFO, these will
762 * trigger an immediate interrupt and stop the DMA job, so we
763 * will always find the error in the FIFO, never in the DMA
764 * buffer.
765 */
766 fifotaken = pl011_fifo_to_tty(uap);
767 }
768
769 spin_unlock(&uap->port.lock);
770 dev_vdbg(uap->port.dev,
771 "Took %d chars from DMA buffer and %d chars from the FIFO\n",
772 dma_count, fifotaken);
773 tty_flip_buffer_push(tty);
774 spin_lock(&uap->port.lock);
775}
776
777static void pl011_dma_rx_irq(struct uart_amba_port *uap)
778{
779 struct pl011_dmarx_data *dmarx = &uap->dmarx;
780 struct dma_chan *rxchan = dmarx->chan;
781 struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
782 &dmarx->sgbuf_b : &dmarx->sgbuf_a;
783 size_t pending;
784 struct dma_tx_state state;
785 enum dma_status dmastat;
786
787 /*
788 * Pause the transfer so we can trust the current counter,
789 * do this before we pause the PL011 block, else we may
790 * overflow the FIFO.
791 */
792 if (dmaengine_pause(rxchan))
793 dev_err(uap->port.dev, "unable to pause DMA transfer\n");
794 dmastat = rxchan->device->device_tx_status(rxchan,
795 dmarx->cookie, &state);
796 if (dmastat != DMA_PAUSED)
797 dev_err(uap->port.dev, "unable to pause DMA transfer\n");
798
799 /* Disable RX DMA - incoming data will wait in the FIFO */
800 uap->dmacr &= ~UART011_RXDMAE;
801 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
802 uap->dmarx.running = false;
803
804 pending = sgbuf->sg.length - state.residue;
805 BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
806 /* Then we terminate the transfer - we now know our residue */
807 dmaengine_terminate_all(rxchan);
808
809 /*
810 * This will take the chars we have so far and insert
811 * into the framework.
812 */
813 pl011_dma_rx_chars(uap, pending, dmarx->use_buf_b, true);
814
815 /* Switch buffer & re-trigger DMA job */
816 dmarx->use_buf_b = !dmarx->use_buf_b;
817 if (pl011_dma_rx_trigger_dma(uap)) {
818 dev_dbg(uap->port.dev, "could not retrigger RX DMA job "
819 "fall back to interrupt mode\n");
820 uap->im |= UART011_RXIM;
821 writew(uap->im, uap->port.membase + UART011_IMSC);
822 }
823}
824
825static void pl011_dma_rx_callback(void *data)
826{
827 struct uart_amba_port *uap = data;
828 struct pl011_dmarx_data *dmarx = &uap->dmarx;
829 bool lastbuf = dmarx->use_buf_b;
830 int ret;
831
832 /*
833 * This completion interrupt occurs typically when the
834 * RX buffer is totally stuffed but no timeout has yet
835 * occurred. When that happens, we just want the RX
836 * routine to flush out the secondary DMA buffer while
837 * we immediately trigger the next DMA job.
838 */
839 spin_lock_irq(&uap->port.lock);
840 uap->dmarx.running = false;
841 dmarx->use_buf_b = !lastbuf;
842 ret = pl011_dma_rx_trigger_dma(uap);
843
844 pl011_dma_rx_chars(uap, PL011_DMA_BUFFER_SIZE, lastbuf, false);
845 spin_unlock_irq(&uap->port.lock);
846 /*
847 * Do this check after we picked the DMA chars so we don't
848 * get some IRQ immediately from RX.
849 */
850 if (ret) {
851 dev_dbg(uap->port.dev, "could not retrigger RX DMA job "
852 "fall back to interrupt mode\n");
853 uap->im |= UART011_RXIM;
854 writew(uap->im, uap->port.membase + UART011_IMSC);
855 }
856}
857
858/*
859 * Stop accepting received characters, when we're shutting down or
860 * suspending this port.
861 * Locking: called with port lock held and IRQs disabled.
862 */
863static inline void pl011_dma_rx_stop(struct uart_amba_port *uap)
864{
865 /* FIXME. Just disable the DMA enable */
866 uap->dmacr &= ~UART011_RXDMAE;
867 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
868}
869
870static void pl011_dma_startup(struct uart_amba_port *uap)
871{
872 int ret;
873
874 if (!uap->dmatx.chan)
875 return;
876
877 uap->dmatx.buf = kmalloc(PL011_DMA_BUFFER_SIZE, GFP_KERNEL);
878 if (!uap->dmatx.buf) {
879 dev_err(uap->port.dev, "no memory for DMA TX buffer\n");
880 uap->port.fifosize = uap->fifosize;
881 return;
882 }
883
884 sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE);
885
886 /* The DMA buffer is now the FIFO the TTY subsystem can use */
887 uap->port.fifosize = PL011_DMA_BUFFER_SIZE;
888 uap->using_tx_dma = true;
889
890 if (!uap->dmarx.chan)
891 goto skip_rx;
892
893 /* Allocate and map DMA RX buffers */
894 ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
895 DMA_FROM_DEVICE);
896 if (ret) {
897 dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
898 "RX buffer A", ret);
899 goto skip_rx;
900 }
901
902 ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_b,
903 DMA_FROM_DEVICE);
904 if (ret) {
905 dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
906 "RX buffer B", ret);
907 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
908 DMA_FROM_DEVICE);
909 goto skip_rx;
910 }
911
912 uap->using_rx_dma = true;
913
914skip_rx:
915 /* Turn on DMA error (RX/TX will be enabled on demand) */
916 uap->dmacr |= UART011_DMAONERR;
917 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
918
919 /*
920 * ST Micro variants has some specific dma burst threshold
921 * compensation. Set this to 16 bytes, so burst will only
922 * be issued above/below 16 bytes.
923 */
924 if (uap->vendor->dma_threshold)
925 writew(ST_UART011_DMAWM_RX_16 | ST_UART011_DMAWM_TX_16,
926 uap->port.membase + ST_UART011_DMAWM);
927
928 if (uap->using_rx_dma) {
929 if (pl011_dma_rx_trigger_dma(uap))
930 dev_dbg(uap->port.dev, "could not trigger initial "
931 "RX DMA job, fall back to interrupt mode\n");
932 }
933}
934
935static void pl011_dma_shutdown(struct uart_amba_port *uap)
936{
937 if (!(uap->using_tx_dma || uap->using_rx_dma))
938 return;
939
940 /* Disable RX and TX DMA */
941 while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
942 barrier();
943
944 spin_lock_irq(&uap->port.lock);
945 uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE);
946 writew(uap->dmacr, uap->port.membase + UART011_DMACR);
947 spin_unlock_irq(&uap->port.lock);
948
949 if (uap->using_tx_dma) {
950 /* In theory, this should already be done by pl011_dma_flush_buffer */
951 dmaengine_terminate_all(uap->dmatx.chan);
952 if (uap->dmatx.queued) {
953 dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
954 DMA_TO_DEVICE);
955 uap->dmatx.queued = false;
956 }
957
958 kfree(uap->dmatx.buf);
959 uap->using_tx_dma = false;
960 }
961
962 if (uap->using_rx_dma) {
963 dmaengine_terminate_all(uap->dmarx.chan);
964 /* Clean up the RX DMA */
965 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a, DMA_FROM_DEVICE);
966 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_b, DMA_FROM_DEVICE);
967 uap->using_rx_dma = false;
968 }
969}
970
971static inline bool pl011_dma_rx_available(struct uart_amba_port *uap)
972{
973 return uap->using_rx_dma;
974}
975
976static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
977{
978 return uap->using_rx_dma && uap->dmarx.running;
979}
980
981
982#else
983/* Blank functions if the DMA engine is not available */
984static inline void pl011_dma_probe(struct uart_amba_port *uap)
985{
986}
987
988static inline void pl011_dma_remove(struct uart_amba_port *uap)
989{
990}
991
992static inline void pl011_dma_startup(struct uart_amba_port *uap)
993{
994}
995
996static inline void pl011_dma_shutdown(struct uart_amba_port *uap)
997{
998}
999
1000static inline bool pl011_dma_tx_irq(struct uart_amba_port *uap)
1001{
1002 return false;
1003}
1004
1005static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
1006{
1007}
1008
1009static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
1010{
1011 return false;
1012}
1013
1014static inline void pl011_dma_rx_irq(struct uart_amba_port *uap)
1015{
1016}
1017
1018static inline void pl011_dma_rx_stop(struct uart_amba_port *uap)
1019{
1020}
1021
1022static inline int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
1023{
1024 return -EIO;
1025}
1026
1027static inline bool pl011_dma_rx_available(struct uart_amba_port *uap)
1028{
1029 return false;
1030}
1031
1032static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
1033{
1034 return false;
1035}
1036
1037#define pl011_dma_flush_buffer NULL
1038#endif
1039
1040
1041/*
1042 * pl011_lockup_wa
1043 * This workaround aims to break the deadlock situation
1044 * when after long transfer over uart in hardware flow
1045 * control, uart interrupt registers cannot be cleared.
1046 * Hence uart transfer gets blocked.
1047 *
1048 * It is seen that during such deadlock condition ICR
1049 * don't get cleared even on multiple write. This leads
1050 * pass_counter to decrease and finally reach zero. This
1051 * can be taken as trigger point to run this UART_BT_WA.
1052 *
1053 */
1054static void pl011_lockup_wa(unsigned long data)
1055{
1056 struct uart_amba_port *uap = amba_ports[0];
1057 void __iomem *base = uap->port.membase;
1058 struct circ_buf *xmit = &uap->port.state->xmit;
1059 struct tty_struct *tty = uap->port.state->port.tty;
1060 int buf_empty_retries = 200;
1061 int loop;
1062
1063 /* Stop HCI layer from submitting data for tx */
1064 tty->hw_stopped = 1;
1065 while (!uart_circ_empty(xmit)) {
1066 if (buf_empty_retries-- == 0)
1067 break;
1068 udelay(100);
1069 }
1070
1071 /* Backup registers */
1072 for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
1073 uart_wa_regdata[loop] = readl(base + uart_wa_reg[loop]);
1074
1075 /* Disable UART so that FIFO data is flushed out */
1076 writew(0x00, uap->port.membase + UART011_CR);
1077
1078 /* Soft reset UART module */
1079 if (uap->port.dev->platform_data) {
1080 struct amba_pl011_data *plat;
1081
1082 plat = uap->port.dev->platform_data;
1083 if (plat->reset)
1084 plat->reset();
1085 }
1086
1087 /* Restore registers */
1088 for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
1089 writew(uart_wa_regdata[loop] ,
1090 uap->port.membase + uart_wa_reg[loop]);
1091
1092 /* Initialise the old status of the modem signals */
1093 uap->old_status = readw(uap->port.membase + UART01x_FR) &
1094 UART01x_FR_MODEM_ANY;
1095
1096 if (readl(base + UART011_MIS) & 0x2)
1097 printk(KERN_EMERG "UART_BT_WA: ***FAILED***\n");
1098
1099 /* Start Tx/Rx */
1100 tty->hw_stopped = 0;
1101}
1102
1103static void pl011_stop_tx(struct uart_port *port)
1104{
1105 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1106
1107 uap->im &= ~UART011_TXIM;
1108 writew(uap->im, uap->port.membase + UART011_IMSC);
1109 pl011_dma_tx_stop(uap);
1110}
1111
1112static void pl011_start_tx(struct uart_port *port)
1113{
1114 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1115
1116 if (!pl011_dma_tx_start(uap)) {
1117 uap->im |= UART011_TXIM;
1118 writew(uap->im, uap->port.membase + UART011_IMSC);
1119 }
1120}
1121
1122static void pl011_stop_rx(struct uart_port *port)
1123{
1124 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1125
1126 uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
1127 UART011_PEIM|UART011_BEIM|UART011_OEIM);
1128 writew(uap->im, uap->port.membase + UART011_IMSC);
1129
1130 pl011_dma_rx_stop(uap);
1131}
1132
1133static void pl011_enable_ms(struct uart_port *port)
1134{
1135 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1136
1137 uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
1138 writew(uap->im, uap->port.membase + UART011_IMSC);
1139}
1140
1141static void pl011_rx_chars(struct uart_amba_port *uap)
1142{
1143 struct tty_struct *tty = uap->port.state->port.tty;
1144
1145 pl011_fifo_to_tty(uap);
1146
1147 spin_unlock(&uap->port.lock);
1148 tty_flip_buffer_push(tty);
1149 /*
1150 * If we were temporarily out of DMA mode for a while,
1151 * attempt to switch back to DMA mode again.
1152 */
1153 if (pl011_dma_rx_available(uap)) {
1154 if (pl011_dma_rx_trigger_dma(uap)) {
1155 dev_dbg(uap->port.dev, "could not trigger RX DMA job "
1156 "fall back to interrupt mode again\n");
1157 uap->im |= UART011_RXIM;
1158 } else
1159 uap->im &= ~UART011_RXIM;
1160 writew(uap->im, uap->port.membase + UART011_IMSC);
1161 }
1162 spin_lock(&uap->port.lock);
1163}
1164
1165static void pl011_tx_chars(struct uart_amba_port *uap)
1166{
1167 struct circ_buf *xmit = &uap->port.state->xmit;
1168 int count;
1169
1170 if (uap->port.x_char) {
1171 writew(uap->port.x_char, uap->port.membase + UART01x_DR);
1172 uap->port.icount.tx++;
1173 uap->port.x_char = 0;
1174 return;
1175 }
1176 if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
1177 pl011_stop_tx(&uap->port);
1178 return;
1179 }
1180
1181 /* If we are using DMA mode, try to send some characters. */
1182 if (pl011_dma_tx_irq(uap))
1183 return;
1184
1185 count = uap->fifosize >> 1;
1186 do {
1187 writew(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
1188 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
1189 uap->port.icount.tx++;
1190 if (uart_circ_empty(xmit))
1191 break;
1192 } while (--count > 0);
1193
1194 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1195 uart_write_wakeup(&uap->port);
1196
1197 if (uart_circ_empty(xmit))
1198 pl011_stop_tx(&uap->port);
1199}
1200
1201static void pl011_modem_status(struct uart_amba_port *uap)
1202{
1203 unsigned int status, delta;
1204
1205 status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
1206
1207 delta = status ^ uap->old_status;
1208 uap->old_status = status;
1209
1210 if (!delta)
1211 return;
1212
1213 if (delta & UART01x_FR_DCD)
1214 uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
1215
1216 if (delta & UART01x_FR_DSR)
1217 uap->port.icount.dsr++;
1218
1219 if (delta & UART01x_FR_CTS)
1220 uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS);
1221
1222 wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
1223}
1224
1225static irqreturn_t pl011_int(int irq, void *dev_id)
1226{
1227 struct uart_amba_port *uap = dev_id;
1228 unsigned long flags;
1229 unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
1230 int handled = 0;
1231
1232 spin_lock_irqsave(&uap->port.lock, flags);
1233
1234 status = readw(uap->port.membase + UART011_MIS);
1235 if (status) {
1236 do {
1237 writew(status & ~(UART011_TXIS|UART011_RTIS|
1238 UART011_RXIS),
1239 uap->port.membase + UART011_ICR);
1240
1241 if (status & (UART011_RTIS|UART011_RXIS)) {
1242 if (pl011_dma_rx_running(uap))
1243 pl011_dma_rx_irq(uap);
1244 else
1245 pl011_rx_chars(uap);
1246 }
1247 if (status & (UART011_DSRMIS|UART011_DCDMIS|
1248 UART011_CTSMIS|UART011_RIMIS))
1249 pl011_modem_status(uap);
1250 if (status & UART011_TXIS)
1251 pl011_tx_chars(uap);
1252
1253 if (pass_counter-- == 0) {
1254 if (uap->interrupt_may_hang)
1255 tasklet_schedule(&pl011_lockup_tlet);
1256 break;
1257 }
1258
1259 status = readw(uap->port.membase + UART011_MIS);
1260 } while (status != 0);
1261 handled = 1;
1262 }
1263
1264 spin_unlock_irqrestore(&uap->port.lock, flags);
1265
1266 return IRQ_RETVAL(handled);
1267}
1268
1269static unsigned int pl01x_tx_empty(struct uart_port *port)
1270{
1271 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1272 unsigned int status = readw(uap->port.membase + UART01x_FR);
1273 return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
1274}
1275
1276static unsigned int pl01x_get_mctrl(struct uart_port *port)
1277{
1278 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1279 unsigned int result = 0;
1280 unsigned int status = readw(uap->port.membase + UART01x_FR);
1281
1282#define TIOCMBIT(uartbit, tiocmbit) \
1283 if (status & uartbit) \
1284 result |= tiocmbit
1285
1286 TIOCMBIT(UART01x_FR_DCD, TIOCM_CAR);
1287 TIOCMBIT(UART01x_FR_DSR, TIOCM_DSR);
1288 TIOCMBIT(UART01x_FR_CTS, TIOCM_CTS);
1289 TIOCMBIT(UART011_FR_RI, TIOCM_RNG);
1290#undef TIOCMBIT
1291 return result;
1292}
1293
1294static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
1295{
1296 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1297 unsigned int cr;
1298
1299 cr = readw(uap->port.membase + UART011_CR);
1300
1301#define TIOCMBIT(tiocmbit, uartbit) \
1302 if (mctrl & tiocmbit) \
1303 cr |= uartbit; \
1304 else \
1305 cr &= ~uartbit
1306
1307 TIOCMBIT(TIOCM_RTS, UART011_CR_RTS);
1308 TIOCMBIT(TIOCM_DTR, UART011_CR_DTR);
1309 TIOCMBIT(TIOCM_OUT1, UART011_CR_OUT1);
1310 TIOCMBIT(TIOCM_OUT2, UART011_CR_OUT2);
1311 TIOCMBIT(TIOCM_LOOP, UART011_CR_LBE);
1312
1313 if (uap->autorts) {
1314 /* We need to disable auto-RTS if we want to turn RTS off */
1315 TIOCMBIT(TIOCM_RTS, UART011_CR_RTSEN);
1316 }
1317#undef TIOCMBIT
1318
1319 writew(cr, uap->port.membase + UART011_CR);
1320}
1321
1322static void pl011_break_ctl(struct uart_port *port, int break_state)
1323{
1324 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1325 unsigned long flags;
1326 unsigned int lcr_h;
1327
1328 spin_lock_irqsave(&uap->port.lock, flags);
1329 lcr_h = readw(uap->port.membase + uap->lcrh_tx);
1330 if (break_state == -1)
1331 lcr_h |= UART01x_LCRH_BRK;
1332 else
1333 lcr_h &= ~UART01x_LCRH_BRK;
1334 writew(lcr_h, uap->port.membase + uap->lcrh_tx);
1335 spin_unlock_irqrestore(&uap->port.lock, flags);
1336}
1337
1338#ifdef CONFIG_CONSOLE_POLL
1339static int pl010_get_poll_char(struct uart_port *port)
1340{
1341 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1342 unsigned int status;
1343
1344 status = readw(uap->port.membase + UART01x_FR);
1345 if (status & UART01x_FR_RXFE)
1346 return NO_POLL_CHAR;
1347
1348 return readw(uap->port.membase + UART01x_DR);
1349}
1350
1351static void pl010_put_poll_char(struct uart_port *port,
1352 unsigned char ch)
1353{
1354 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1355
1356 while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
1357 barrier();
1358
1359 writew(ch, uap->port.membase + UART01x_DR);
1360}
1361
1362#endif /* CONFIG_CONSOLE_POLL */
1363
1364static int pl011_startup(struct uart_port *port)
1365{
1366 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1367 unsigned int cr;
1368 int retval;
1369
1370 /*
1371 * Try to enable the clock producer.
1372 */
1373 retval = clk_enable(uap->clk);
1374 if (retval)
1375 goto out;
1376
1377 uap->port.uartclk = clk_get_rate(uap->clk);
1378
1379 /*
1380 * Allocate the IRQ
1381 */
1382 retval = request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap);
1383 if (retval)
1384 goto clk_dis;
1385
1386 writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
1387
1388 /*
1389 * Provoke TX FIFO interrupt into asserting.
1390 */
1391 cr = UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_LBE;
1392 writew(cr, uap->port.membase + UART011_CR);
1393 writew(0, uap->port.membase + UART011_FBRD);
1394 writew(1, uap->port.membase + UART011_IBRD);
1395 writew(0, uap->port.membase + uap->lcrh_rx);
1396 if (uap->lcrh_tx != uap->lcrh_rx) {
1397 int i;
1398 /*
1399 * Wait 10 PCLKs before writing LCRH_TX register,
1400 * to get this delay write read only register 10 times
1401 */
1402 for (i = 0; i < 10; ++i)
1403 writew(0xff, uap->port.membase + UART011_MIS);
1404 writew(0, uap->port.membase + uap->lcrh_tx);
1405 }
1406 writew(0, uap->port.membase + UART01x_DR);
1407 while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
1408 barrier();
1409
1410 cr = UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
1411 writew(cr, uap->port.membase + UART011_CR);
1412
1413 /* Clear pending error interrupts */
1414 writew(UART011_OEIS | UART011_BEIS | UART011_PEIS | UART011_FEIS,
1415 uap->port.membase + UART011_ICR);
1416
1417 /*
1418 * initialise the old status of the modem signals
1419 */
1420 uap->old_status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
1421
1422 /* Startup DMA */
1423 pl011_dma_startup(uap);
1424
1425 /*
1426 * Finally, enable interrupts, only timeouts when using DMA
1427 * if initial RX DMA job failed, start in interrupt mode
1428 * as well.
1429 */
1430 spin_lock_irq(&uap->port.lock);
1431 uap->im = UART011_RTIM;
1432 if (!pl011_dma_rx_running(uap))
1433 uap->im |= UART011_RXIM;
1434 writew(uap->im, uap->port.membase + UART011_IMSC);
1435 spin_unlock_irq(&uap->port.lock);
1436
1437 if (uap->port.dev->platform_data) {
1438 struct amba_pl011_data *plat;
1439
1440 plat = uap->port.dev->platform_data;
1441 if (plat->init)
1442 plat->init();
1443 }
1444
1445 return 0;
1446
1447 clk_dis:
1448 clk_disable(uap->clk);
1449 out:
1450 return retval;
1451}
1452
1453static void pl011_shutdown_channel(struct uart_amba_port *uap,
1454 unsigned int lcrh)
1455{
1456 unsigned long val;
1457
1458 val = readw(uap->port.membase + lcrh);
1459 val &= ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN);
1460 writew(val, uap->port.membase + lcrh);
1461}
1462
1463static void pl011_shutdown(struct uart_port *port)
1464{
1465 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1466
1467 /*
1468 * disable all interrupts
1469 */
1470 spin_lock_irq(&uap->port.lock);
1471 uap->im = 0;
1472 writew(uap->im, uap->port.membase + UART011_IMSC);
1473 writew(0xffff, uap->port.membase + UART011_ICR);
1474 spin_unlock_irq(&uap->port.lock);
1475
1476 pl011_dma_shutdown(uap);
1477
1478 /*
1479 * Free the interrupt
1480 */
1481 free_irq(uap->port.irq, uap);
1482
1483 /*
1484 * disable the port
1485 */
1486 uap->autorts = false;
1487 writew(UART01x_CR_UARTEN | UART011_CR_TXE, uap->port.membase + UART011_CR);
1488
1489 /*
1490 * disable break condition and fifos
1491 */
1492 pl011_shutdown_channel(uap, uap->lcrh_rx);
1493 if (uap->lcrh_rx != uap->lcrh_tx)
1494 pl011_shutdown_channel(uap, uap->lcrh_tx);
1495
1496 /*
1497 * Shut down the clock producer
1498 */
1499 clk_disable(uap->clk);
1500
1501 if (uap->port.dev->platform_data) {
1502 struct amba_pl011_data *plat;
1503
1504 plat = uap->port.dev->platform_data;
1505 if (plat->exit)
1506 plat->exit();
1507 }
1508
1509}
1510
1511static void
1512pl011_set_termios(struct uart_port *port, struct ktermios *termios,
1513 struct ktermios *old)
1514{
1515 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1516 unsigned int lcr_h, old_cr;
1517 unsigned long flags;
1518 unsigned int baud, quot, clkdiv;
1519
1520 if (uap->vendor->oversampling)
1521 clkdiv = 8;
1522 else
1523 clkdiv = 16;
1524
1525 /*
1526 * Ask the core to calculate the divisor for us.
1527 */
1528 baud = uart_get_baud_rate(port, termios, old, 0,
1529 port->uartclk / clkdiv);
1530
1531 if (baud > port->uartclk/16)
1532 quot = DIV_ROUND_CLOSEST(port->uartclk * 8, baud);
1533 else
1534 quot = DIV_ROUND_CLOSEST(port->uartclk * 4, baud);
1535
1536 switch (termios->c_cflag & CSIZE) {
1537 case CS5:
1538 lcr_h = UART01x_LCRH_WLEN_5;
1539 break;
1540 case CS6:
1541 lcr_h = UART01x_LCRH_WLEN_6;
1542 break;
1543 case CS7:
1544 lcr_h = UART01x_LCRH_WLEN_7;
1545 break;
1546 default: // CS8
1547 lcr_h = UART01x_LCRH_WLEN_8;
1548 break;
1549 }
1550 if (termios->c_cflag & CSTOPB)
1551 lcr_h |= UART01x_LCRH_STP2;
1552 if (termios->c_cflag & PARENB) {
1553 lcr_h |= UART01x_LCRH_PEN;
1554 if (!(termios->c_cflag & PARODD))
1555 lcr_h |= UART01x_LCRH_EPS;
1556 }
1557 if (uap->fifosize > 1)
1558 lcr_h |= UART01x_LCRH_FEN;
1559
1560 spin_lock_irqsave(&port->lock, flags);
1561
1562 /*
1563 * Update the per-port timeout.
1564 */
1565 uart_update_timeout(port, termios->c_cflag, baud);
1566
1567 port->read_status_mask = UART011_DR_OE | 255;
1568 if (termios->c_iflag & INPCK)
1569 port->read_status_mask |= UART011_DR_FE | UART011_DR_PE;
1570 if (termios->c_iflag & (BRKINT | PARMRK))
1571 port->read_status_mask |= UART011_DR_BE;
1572
1573 /*
1574 * Characters to ignore
1575 */
1576 port->ignore_status_mask = 0;
1577 if (termios->c_iflag & IGNPAR)
1578 port->ignore_status_mask |= UART011_DR_FE | UART011_DR_PE;
1579 if (termios->c_iflag & IGNBRK) {
1580 port->ignore_status_mask |= UART011_DR_BE;
1581 /*
1582 * If we're ignoring parity and break indicators,
1583 * ignore overruns too (for real raw support).
1584 */
1585 if (termios->c_iflag & IGNPAR)
1586 port->ignore_status_mask |= UART011_DR_OE;
1587 }
1588
1589 /*
1590 * Ignore all characters if CREAD is not set.
1591 */
1592 if ((termios->c_cflag & CREAD) == 0)
1593 port->ignore_status_mask |= UART_DUMMY_DR_RX;
1594
1595 if (UART_ENABLE_MS(port, termios->c_cflag))
1596 pl011_enable_ms(port);
1597
1598 /* first, disable everything */
1599 old_cr = readw(port->membase + UART011_CR);
1600 writew(0, port->membase + UART011_CR);
1601
1602 if (termios->c_cflag & CRTSCTS) {
1603 if (old_cr & UART011_CR_RTS)
1604 old_cr |= UART011_CR_RTSEN;
1605
1606 old_cr |= UART011_CR_CTSEN;
1607 uap->autorts = true;
1608 } else {
1609 old_cr &= ~(UART011_CR_CTSEN | UART011_CR_RTSEN);
1610 uap->autorts = false;
1611 }
1612
1613 if (uap->vendor->oversampling) {
1614 if (baud > port->uartclk / 16)
1615 old_cr |= ST_UART011_CR_OVSFACT;
1616 else
1617 old_cr &= ~ST_UART011_CR_OVSFACT;
1618 }
1619
1620 /* Set baud rate */
1621 writew(quot & 0x3f, port->membase + UART011_FBRD);
1622 writew(quot >> 6, port->membase + UART011_IBRD);
1623
1624 /*
1625 * ----------v----------v----------v----------v-----
1626 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
1627 * ----------^----------^----------^----------^-----
1628 */
1629 writew(lcr_h, port->membase + uap->lcrh_rx);
1630 if (uap->lcrh_rx != uap->lcrh_tx) {
1631 int i;
1632 /*
1633 * Wait 10 PCLKs before writing LCRH_TX register,
1634 * to get this delay write read only register 10 times
1635 */
1636 for (i = 0; i < 10; ++i)
1637 writew(0xff, uap->port.membase + UART011_MIS);
1638 writew(lcr_h, port->membase + uap->lcrh_tx);
1639 }
1640 writew(old_cr, port->membase + UART011_CR);
1641
1642 spin_unlock_irqrestore(&port->lock, flags);
1643}
1644
1645static const char *pl011_type(struct uart_port *port)
1646{
1647 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1648 return uap->port.type == PORT_AMBA ? uap->type : NULL;
1649}
1650
1651/*
1652 * Release the memory region(s) being used by 'port'
1653 */
1654static void pl010_release_port(struct uart_port *port)
1655{
1656 release_mem_region(port->mapbase, SZ_4K);
1657}
1658
1659/*
1660 * Request the memory region(s) being used by 'port'
1661 */
1662static int pl010_request_port(struct uart_port *port)
1663{
1664 return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
1665 != NULL ? 0 : -EBUSY;
1666}
1667
1668/*
1669 * Configure/autoconfigure the port.
1670 */
1671static void pl010_config_port(struct uart_port *port, int flags)
1672{
1673 if (flags & UART_CONFIG_TYPE) {
1674 port->type = PORT_AMBA;
1675 pl010_request_port(port);
1676 }
1677}
1678
1679/*
1680 * verify the new serial_struct (for TIOCSSERIAL).
1681 */
1682static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
1683{
1684 int ret = 0;
1685 if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
1686 ret = -EINVAL;
1687 if (ser->irq < 0 || ser->irq >= nr_irqs)
1688 ret = -EINVAL;
1689 if (ser->baud_base < 9600)
1690 ret = -EINVAL;
1691 return ret;
1692}
1693
1694static struct uart_ops amba_pl011_pops = {
1695 .tx_empty = pl01x_tx_empty,
1696 .set_mctrl = pl011_set_mctrl,
1697 .get_mctrl = pl01x_get_mctrl,
1698 .stop_tx = pl011_stop_tx,
1699 .start_tx = pl011_start_tx,
1700 .stop_rx = pl011_stop_rx,
1701 .enable_ms = pl011_enable_ms,
1702 .break_ctl = pl011_break_ctl,
1703 .startup = pl011_startup,
1704 .shutdown = pl011_shutdown,
1705 .flush_buffer = pl011_dma_flush_buffer,
1706 .set_termios = pl011_set_termios,
1707 .type = pl011_type,
1708 .release_port = pl010_release_port,
1709 .request_port = pl010_request_port,
1710 .config_port = pl010_config_port,
1711 .verify_port = pl010_verify_port,
1712#ifdef CONFIG_CONSOLE_POLL
1713 .poll_get_char = pl010_get_poll_char,
1714 .poll_put_char = pl010_put_poll_char,
1715#endif
1716};
1717
1718static struct uart_amba_port *amba_ports[UART_NR];
1719
1720#ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE
1721
1722static void pl011_console_putchar(struct uart_port *port, int ch)
1723{
1724 struct uart_amba_port *uap = (struct uart_amba_port *)port;
1725
1726 while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
1727 barrier();
1728 writew(ch, uap->port.membase + UART01x_DR);
1729}
1730
1731static void
1732pl011_console_write(struct console *co, const char *s, unsigned int count)
1733{
1734 struct uart_amba_port *uap = amba_ports[co->index];
1735 unsigned int status, old_cr, new_cr;
1736
1737 clk_enable(uap->clk);
1738
1739 /*
1740 * First save the CR then disable the interrupts
1741 */
1742 old_cr = readw(uap->port.membase + UART011_CR);
1743 new_cr = old_cr & ~UART011_CR_CTSEN;
1744 new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
1745 writew(new_cr, uap->port.membase + UART011_CR);
1746
1747 uart_console_write(&uap->port, s, count, pl011_console_putchar);
1748
1749 /*
1750 * Finally, wait for transmitter to become empty
1751 * and restore the TCR
1752 */
1753 do {
1754 status = readw(uap->port.membase + UART01x_FR);
1755 } while (status & UART01x_FR_BUSY);
1756 writew(old_cr, uap->port.membase + UART011_CR);
1757
1758 clk_disable(uap->clk);
1759}
1760
1761static void __init
1762pl011_console_get_options(struct uart_amba_port *uap, int *baud,
1763 int *parity, int *bits)
1764{
1765 if (readw(uap->port.membase + UART011_CR) & UART01x_CR_UARTEN) {
1766 unsigned int lcr_h, ibrd, fbrd;
1767
1768 lcr_h = readw(uap->port.membase + uap->lcrh_tx);
1769
1770 *parity = 'n';
1771 if (lcr_h & UART01x_LCRH_PEN) {
1772 if (lcr_h & UART01x_LCRH_EPS)
1773 *parity = 'e';
1774 else
1775 *parity = 'o';
1776 }
1777
1778 if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
1779 *bits = 7;
1780 else
1781 *bits = 8;
1782
1783 ibrd = readw(uap->port.membase + UART011_IBRD);
1784 fbrd = readw(uap->port.membase + UART011_FBRD);
1785
1786 *baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd);
1787
1788 if (uap->vendor->oversampling) {
1789 if (readw(uap->port.membase + UART011_CR)
1790 & ST_UART011_CR_OVSFACT)
1791 *baud *= 2;
1792 }
1793 }
1794}
1795
1796static int __init pl011_console_setup(struct console *co, char *options)
1797{
1798 struct uart_amba_port *uap;
1799 int baud = 38400;
1800 int bits = 8;
1801 int parity = 'n';
1802 int flow = 'n';
1803
1804 /*
1805 * Check whether an invalid uart number has been specified, and
1806 * if so, search for the first available port that does have
1807 * console support.
1808 */
1809 if (co->index >= UART_NR)
1810 co->index = 0;
1811 uap = amba_ports[co->index];
1812 if (!uap)
1813 return -ENODEV;
1814
1815 if (uap->port.dev->platform_data) {
1816 struct amba_pl011_data *plat;
1817
1818 plat = uap->port.dev->platform_data;
1819 if (plat->init)
1820 plat->init();
1821 }
1822
1823 uap->port.uartclk = clk_get_rate(uap->clk);
1824
1825 if (options)
1826 uart_parse_options(options, &baud, &parity, &bits, &flow);
1827 else
1828 pl011_console_get_options(uap, &baud, &parity, &bits);
1829
1830 return uart_set_options(&uap->port, co, baud, parity, bits, flow);
1831}
1832
1833static struct uart_driver amba_reg;
1834static struct console amba_console = {
1835 .name = "ttyAMA",
1836 .write = pl011_console_write,
1837 .device = uart_console_device,
1838 .setup = pl011_console_setup,
1839 .flags = CON_PRINTBUFFER,
1840 .index = -1,
1841 .data = &amba_reg,
1842};
1843
1844#define AMBA_CONSOLE (&amba_console)
1845#else
1846#define AMBA_CONSOLE NULL
1847#endif
1848
1849static struct uart_driver amba_reg = {
1850 .owner = THIS_MODULE,
1851 .driver_name = "ttyAMA",
1852 .dev_name = "ttyAMA",
1853 .major = SERIAL_AMBA_MAJOR,
1854 .minor = SERIAL_AMBA_MINOR,
1855 .nr = UART_NR,
1856 .cons = AMBA_CONSOLE,
1857};
1858
1859static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
1860{
1861 struct uart_amba_port *uap;
1862 struct vendor_data *vendor = id->data;
1863 void __iomem *base;
1864 int i, ret;
1865
1866 for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
1867 if (amba_ports[i] == NULL)
1868 break;
1869
1870 if (i == ARRAY_SIZE(amba_ports)) {
1871 ret = -EBUSY;
1872 goto out;
1873 }
1874
1875 uap = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
1876 if (uap == NULL) {
1877 ret = -ENOMEM;
1878 goto out;
1879 }
1880
1881 base = ioremap(dev->res.start, resource_size(&dev->res));
1882 if (!base) {
1883 ret = -ENOMEM;
1884 goto free;
1885 }
1886
1887 uap->clk = clk_get(&dev->dev, NULL);
1888 if (IS_ERR(uap->clk)) {
1889 ret = PTR_ERR(uap->clk);
1890 goto unmap;
1891 }
1892
1893 uap->vendor = vendor;
1894 uap->lcrh_rx = vendor->lcrh_rx;
1895 uap->lcrh_tx = vendor->lcrh_tx;
1896 uap->fifosize = vendor->fifosize;
1897 uap->interrupt_may_hang = vendor->interrupt_may_hang;
1898 uap->port.dev = &dev->dev;
1899 uap->port.mapbase = dev->res.start;
1900 uap->port.membase = base;
1901 uap->port.iotype = UPIO_MEM;
1902 uap->port.irq = dev->irq[0];
1903 uap->port.fifosize = uap->fifosize;
1904 uap->port.ops = &amba_pl011_pops;
1905 uap->port.flags = UPF_BOOT_AUTOCONF;
1906 uap->port.line = i;
1907 pl011_dma_probe(uap);
1908
1909 snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev));
1910
1911 amba_ports[i] = uap;
1912
1913 amba_set_drvdata(dev, uap);
1914 ret = uart_add_one_port(&amba_reg, &uap->port);
1915 if (ret) {
1916 amba_set_drvdata(dev, NULL);
1917 amba_ports[i] = NULL;
1918 pl011_dma_remove(uap);
1919 clk_put(uap->clk);
1920 unmap:
1921 iounmap(base);
1922 free:
1923 kfree(uap);
1924 }
1925 out:
1926 return ret;
1927}
1928
1929static int pl011_remove(struct amba_device *dev)
1930{
1931 struct uart_amba_port *uap = amba_get_drvdata(dev);
1932 int i;
1933
1934 amba_set_drvdata(dev, NULL);
1935
1936 uart_remove_one_port(&amba_reg, &uap->port);
1937
1938 for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
1939 if (amba_ports[i] == uap)
1940 amba_ports[i] = NULL;
1941
1942 pl011_dma_remove(uap);
1943 iounmap(uap->port.membase);
1944 clk_put(uap->clk);
1945 kfree(uap);
1946 return 0;
1947}
1948
1949#ifdef CONFIG_PM
1950static int pl011_suspend(struct amba_device *dev, pm_message_t state)
1951{
1952 struct uart_amba_port *uap = amba_get_drvdata(dev);
1953
1954 if (!uap)
1955 return -EINVAL;
1956
1957 return uart_suspend_port(&amba_reg, &uap->port);
1958}
1959
1960static int pl011_resume(struct amba_device *dev)
1961{
1962 struct uart_amba_port *uap = amba_get_drvdata(dev);
1963
1964 if (!uap)
1965 return -EINVAL;
1966
1967 return uart_resume_port(&amba_reg, &uap->port);
1968}
1969#endif
1970
1971static struct amba_id pl011_ids[] = {
1972 {
1973 .id = 0x00041011,
1974 .mask = 0x000fffff,
1975 .data = &vendor_arm,
1976 },
1977 {
1978 .id = 0x00380802,
1979 .mask = 0x00ffffff,
1980 .data = &vendor_st,
1981 },
1982 { 0, 0 },
1983};
1984
1985static struct amba_driver pl011_driver = {
1986 .drv = {
1987 .name = "uart-pl011",
1988 },
1989 .id_table = pl011_ids,
1990 .probe = pl011_probe,
1991 .remove = pl011_remove,
1992#ifdef CONFIG_PM
1993 .suspend = pl011_suspend,
1994 .resume = pl011_resume,
1995#endif
1996};
1997
1998static int __init pl011_init(void)
1999{
2000 int ret;
2001 printk(KERN_INFO "Serial: AMBA PL011 UART driver\n");
2002
2003 ret = uart_register_driver(&amba_reg);
2004 if (ret == 0) {
2005 ret = amba_driver_register(&pl011_driver);
2006 if (ret)
2007 uart_unregister_driver(&amba_reg);
2008 }
2009 return ret;
2010}
2011
2012static void __exit pl011_exit(void)
2013{
2014 amba_driver_unregister(&pl011_driver);
2015 uart_unregister_driver(&amba_reg);
2016}
2017
2018/*
2019 * While this can be a module, if builtin it's most likely the console
2020 * So let's leave module_exit but move module_init to an earlier place
2021 */
2022arch_initcall(pl011_init);
2023module_exit(pl011_exit);
2024
2025MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
2026MODULE_DESCRIPTION("ARM AMBA serial port driver");
2027MODULE_LICENSE("GPL");
1/*
2 * Driver for AMBA serial ports
3 *
4 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
5 *
6 * Copyright 1999 ARM Limited
7 * Copyright (C) 2000 Deep Blue Solutions Ltd.
8 * Copyright (C) 2010 ST-Ericsson SA
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; either version 2 of the License, or
13 * (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 *
24 * This is a generic driver for ARM AMBA-type serial ports. They
25 * have a lot of 16550-like features, but are not register compatible.
26 * Note that although they do have CTS, DCD and DSR inputs, they do
27 * not have an RI input, nor do they have DTR or RTS outputs. If
28 * required, these have to be supplied via some other means (eg, GPIO)
29 * and hooked into this driver.
30 */
31
32
33#if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
34#define SUPPORT_SYSRQ
35#endif
36
37#include <linux/module.h>
38#include <linux/ioport.h>
39#include <linux/init.h>
40#include <linux/console.h>
41#include <linux/sysrq.h>
42#include <linux/device.h>
43#include <linux/tty.h>
44#include <linux/tty_flip.h>
45#include <linux/serial_core.h>
46#include <linux/serial.h>
47#include <linux/amba/bus.h>
48#include <linux/amba/serial.h>
49#include <linux/clk.h>
50#include <linux/slab.h>
51#include <linux/dmaengine.h>
52#include <linux/dma-mapping.h>
53#include <linux/scatterlist.h>
54#include <linux/delay.h>
55#include <linux/types.h>
56#include <linux/of.h>
57#include <linux/of_device.h>
58#include <linux/pinctrl/consumer.h>
59#include <linux/sizes.h>
60#include <linux/io.h>
61#include <linux/acpi.h>
62
63#include "amba-pl011.h"
64
65#define UART_NR 14
66
67#define SERIAL_AMBA_MAJOR 204
68#define SERIAL_AMBA_MINOR 64
69#define SERIAL_AMBA_NR UART_NR
70
71#define AMBA_ISR_PASS_LIMIT 256
72
73#define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE)
74#define UART_DUMMY_DR_RX (1 << 16)
75
76static u16 pl011_std_offsets[REG_ARRAY_SIZE] = {
77 [REG_DR] = UART01x_DR,
78 [REG_FR] = UART01x_FR,
79 [REG_LCRH_RX] = UART011_LCRH,
80 [REG_LCRH_TX] = UART011_LCRH,
81 [REG_IBRD] = UART011_IBRD,
82 [REG_FBRD] = UART011_FBRD,
83 [REG_CR] = UART011_CR,
84 [REG_IFLS] = UART011_IFLS,
85 [REG_IMSC] = UART011_IMSC,
86 [REG_RIS] = UART011_RIS,
87 [REG_MIS] = UART011_MIS,
88 [REG_ICR] = UART011_ICR,
89 [REG_DMACR] = UART011_DMACR,
90};
91
92/* There is by now at least one vendor with differing details, so handle it */
93struct vendor_data {
94 const u16 *reg_offset;
95 unsigned int ifls;
96 unsigned int fr_busy;
97 unsigned int fr_dsr;
98 unsigned int fr_cts;
99 unsigned int fr_ri;
100 bool access_32b;
101 bool oversampling;
102 bool dma_threshold;
103 bool cts_event_workaround;
104 bool always_enabled;
105 bool fixed_options;
106
107 unsigned int (*get_fifosize)(struct amba_device *dev);
108};
109
110static unsigned int get_fifosize_arm(struct amba_device *dev)
111{
112 return amba_rev(dev) < 3 ? 16 : 32;
113}
114
115static struct vendor_data vendor_arm = {
116 .reg_offset = pl011_std_offsets,
117 .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
118 .fr_busy = UART01x_FR_BUSY,
119 .fr_dsr = UART01x_FR_DSR,
120 .fr_cts = UART01x_FR_CTS,
121 .fr_ri = UART011_FR_RI,
122 .oversampling = false,
123 .dma_threshold = false,
124 .cts_event_workaround = false,
125 .always_enabled = false,
126 .fixed_options = false,
127 .get_fifosize = get_fifosize_arm,
128};
129
130static struct vendor_data vendor_sbsa = {
131 .reg_offset = pl011_std_offsets,
132 .fr_busy = UART01x_FR_BUSY,
133 .fr_dsr = UART01x_FR_DSR,
134 .fr_cts = UART01x_FR_CTS,
135 .fr_ri = UART011_FR_RI,
136 .access_32b = true,
137 .oversampling = false,
138 .dma_threshold = false,
139 .cts_event_workaround = false,
140 .always_enabled = true,
141 .fixed_options = true,
142};
143
144static u16 pl011_st_offsets[REG_ARRAY_SIZE] = {
145 [REG_DR] = UART01x_DR,
146 [REG_ST_DMAWM] = ST_UART011_DMAWM,
147 [REG_ST_TIMEOUT] = ST_UART011_TIMEOUT,
148 [REG_FR] = UART01x_FR,
149 [REG_LCRH_RX] = ST_UART011_LCRH_RX,
150 [REG_LCRH_TX] = ST_UART011_LCRH_TX,
151 [REG_IBRD] = UART011_IBRD,
152 [REG_FBRD] = UART011_FBRD,
153 [REG_CR] = UART011_CR,
154 [REG_IFLS] = UART011_IFLS,
155 [REG_IMSC] = UART011_IMSC,
156 [REG_RIS] = UART011_RIS,
157 [REG_MIS] = UART011_MIS,
158 [REG_ICR] = UART011_ICR,
159 [REG_DMACR] = UART011_DMACR,
160 [REG_ST_XFCR] = ST_UART011_XFCR,
161 [REG_ST_XON1] = ST_UART011_XON1,
162 [REG_ST_XON2] = ST_UART011_XON2,
163 [REG_ST_XOFF1] = ST_UART011_XOFF1,
164 [REG_ST_XOFF2] = ST_UART011_XOFF2,
165 [REG_ST_ITCR] = ST_UART011_ITCR,
166 [REG_ST_ITIP] = ST_UART011_ITIP,
167 [REG_ST_ABCR] = ST_UART011_ABCR,
168 [REG_ST_ABIMSC] = ST_UART011_ABIMSC,
169};
170
171static unsigned int get_fifosize_st(struct amba_device *dev)
172{
173 return 64;
174}
175
176static struct vendor_data vendor_st = {
177 .reg_offset = pl011_st_offsets,
178 .ifls = UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF,
179 .fr_busy = UART01x_FR_BUSY,
180 .fr_dsr = UART01x_FR_DSR,
181 .fr_cts = UART01x_FR_CTS,
182 .fr_ri = UART011_FR_RI,
183 .oversampling = true,
184 .dma_threshold = true,
185 .cts_event_workaround = true,
186 .always_enabled = false,
187 .fixed_options = false,
188 .get_fifosize = get_fifosize_st,
189};
190
191static const u16 pl011_zte_offsets[REG_ARRAY_SIZE] = {
192 [REG_DR] = ZX_UART011_DR,
193 [REG_FR] = ZX_UART011_FR,
194 [REG_LCRH_RX] = ZX_UART011_LCRH,
195 [REG_LCRH_TX] = ZX_UART011_LCRH,
196 [REG_IBRD] = ZX_UART011_IBRD,
197 [REG_FBRD] = ZX_UART011_FBRD,
198 [REG_CR] = ZX_UART011_CR,
199 [REG_IFLS] = ZX_UART011_IFLS,
200 [REG_IMSC] = ZX_UART011_IMSC,
201 [REG_RIS] = ZX_UART011_RIS,
202 [REG_MIS] = ZX_UART011_MIS,
203 [REG_ICR] = ZX_UART011_ICR,
204 [REG_DMACR] = ZX_UART011_DMACR,
205};
206
207static unsigned int get_fifosize_zte(struct amba_device *dev)
208{
209 return 16;
210}
211
212static struct vendor_data vendor_zte = {
213 .reg_offset = pl011_zte_offsets,
214 .access_32b = true,
215 .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
216 .fr_busy = ZX_UART01x_FR_BUSY,
217 .fr_dsr = ZX_UART01x_FR_DSR,
218 .fr_cts = ZX_UART01x_FR_CTS,
219 .fr_ri = ZX_UART011_FR_RI,
220 .get_fifosize = get_fifosize_zte,
221};
222
223/* Deals with DMA transactions */
224
225struct pl011_sgbuf {
226 struct scatterlist sg;
227 char *buf;
228};
229
230struct pl011_dmarx_data {
231 struct dma_chan *chan;
232 struct completion complete;
233 bool use_buf_b;
234 struct pl011_sgbuf sgbuf_a;
235 struct pl011_sgbuf sgbuf_b;
236 dma_cookie_t cookie;
237 bool running;
238 struct timer_list timer;
239 unsigned int last_residue;
240 unsigned long last_jiffies;
241 bool auto_poll_rate;
242 unsigned int poll_rate;
243 unsigned int poll_timeout;
244};
245
246struct pl011_dmatx_data {
247 struct dma_chan *chan;
248 struct scatterlist sg;
249 char *buf;
250 bool queued;
251};
252
253/*
254 * We wrap our port structure around the generic uart_port.
255 */
256struct uart_amba_port {
257 struct uart_port port;
258 const u16 *reg_offset;
259 struct clk *clk;
260 const struct vendor_data *vendor;
261 unsigned int dmacr; /* dma control reg */
262 unsigned int im; /* interrupt mask */
263 unsigned int old_status;
264 unsigned int fifosize; /* vendor-specific */
265 unsigned int old_cr; /* state during shutdown */
266 bool autorts;
267 unsigned int fixed_baud; /* vendor-set fixed baud rate */
268 char type[12];
269#ifdef CONFIG_DMA_ENGINE
270 /* DMA stuff */
271 bool using_tx_dma;
272 bool using_rx_dma;
273 struct pl011_dmarx_data dmarx;
274 struct pl011_dmatx_data dmatx;
275 bool dma_probed;
276#endif
277};
278
279static unsigned int pl011_reg_to_offset(const struct uart_amba_port *uap,
280 unsigned int reg)
281{
282 return uap->reg_offset[reg];
283}
284
285static unsigned int pl011_read(const struct uart_amba_port *uap,
286 unsigned int reg)
287{
288 void __iomem *addr = uap->port.membase + pl011_reg_to_offset(uap, reg);
289
290 return (uap->port.iotype == UPIO_MEM32) ?
291 readl_relaxed(addr) : readw_relaxed(addr);
292}
293
294static void pl011_write(unsigned int val, const struct uart_amba_port *uap,
295 unsigned int reg)
296{
297 void __iomem *addr = uap->port.membase + pl011_reg_to_offset(uap, reg);
298
299 if (uap->port.iotype == UPIO_MEM32)
300 writel_relaxed(val, addr);
301 else
302 writew_relaxed(val, addr);
303}
304
305/*
306 * Reads up to 256 characters from the FIFO or until it's empty and
307 * inserts them into the TTY layer. Returns the number of characters
308 * read from the FIFO.
309 */
310static int pl011_fifo_to_tty(struct uart_amba_port *uap)
311{
312 u16 status;
313 unsigned int ch, flag, max_count = 256;
314 int fifotaken = 0;
315
316 while (max_count--) {
317 status = pl011_read(uap, REG_FR);
318 if (status & UART01x_FR_RXFE)
319 break;
320
321 /* Take chars from the FIFO and update status */
322 ch = pl011_read(uap, REG_DR) | UART_DUMMY_DR_RX;
323 flag = TTY_NORMAL;
324 uap->port.icount.rx++;
325 fifotaken++;
326
327 if (unlikely(ch & UART_DR_ERROR)) {
328 if (ch & UART011_DR_BE) {
329 ch &= ~(UART011_DR_FE | UART011_DR_PE);
330 uap->port.icount.brk++;
331 if (uart_handle_break(&uap->port))
332 continue;
333 } else if (ch & UART011_DR_PE)
334 uap->port.icount.parity++;
335 else if (ch & UART011_DR_FE)
336 uap->port.icount.frame++;
337 if (ch & UART011_DR_OE)
338 uap->port.icount.overrun++;
339
340 ch &= uap->port.read_status_mask;
341
342 if (ch & UART011_DR_BE)
343 flag = TTY_BREAK;
344 else if (ch & UART011_DR_PE)
345 flag = TTY_PARITY;
346 else if (ch & UART011_DR_FE)
347 flag = TTY_FRAME;
348 }
349
350 if (uart_handle_sysrq_char(&uap->port, ch & 255))
351 continue;
352
353 uart_insert_char(&uap->port, ch, UART011_DR_OE, ch, flag);
354 }
355
356 return fifotaken;
357}
358
359
360/*
361 * All the DMA operation mode stuff goes inside this ifdef.
362 * This assumes that you have a generic DMA device interface,
363 * no custom DMA interfaces are supported.
364 */
365#ifdef CONFIG_DMA_ENGINE
366
367#define PL011_DMA_BUFFER_SIZE PAGE_SIZE
368
369static int pl011_sgbuf_init(struct dma_chan *chan, struct pl011_sgbuf *sg,
370 enum dma_data_direction dir)
371{
372 dma_addr_t dma_addr;
373
374 sg->buf = dma_alloc_coherent(chan->device->dev,
375 PL011_DMA_BUFFER_SIZE, &dma_addr, GFP_KERNEL);
376 if (!sg->buf)
377 return -ENOMEM;
378
379 sg_init_table(&sg->sg, 1);
380 sg_set_page(&sg->sg, phys_to_page(dma_addr),
381 PL011_DMA_BUFFER_SIZE, offset_in_page(dma_addr));
382 sg_dma_address(&sg->sg) = dma_addr;
383 sg_dma_len(&sg->sg) = PL011_DMA_BUFFER_SIZE;
384
385 return 0;
386}
387
388static void pl011_sgbuf_free(struct dma_chan *chan, struct pl011_sgbuf *sg,
389 enum dma_data_direction dir)
390{
391 if (sg->buf) {
392 dma_free_coherent(chan->device->dev,
393 PL011_DMA_BUFFER_SIZE, sg->buf,
394 sg_dma_address(&sg->sg));
395 }
396}
397
398static void pl011_dma_probe(struct uart_amba_port *uap)
399{
400 /* DMA is the sole user of the platform data right now */
401 struct amba_pl011_data *plat = dev_get_platdata(uap->port.dev);
402 struct device *dev = uap->port.dev;
403 struct dma_slave_config tx_conf = {
404 .dst_addr = uap->port.mapbase +
405 pl011_reg_to_offset(uap, REG_DR),
406 .dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
407 .direction = DMA_MEM_TO_DEV,
408 .dst_maxburst = uap->fifosize >> 1,
409 .device_fc = false,
410 };
411 struct dma_chan *chan;
412 dma_cap_mask_t mask;
413
414 uap->dma_probed = true;
415 chan = dma_request_slave_channel_reason(dev, "tx");
416 if (IS_ERR(chan)) {
417 if (PTR_ERR(chan) == -EPROBE_DEFER) {
418 uap->dma_probed = false;
419 return;
420 }
421
422 /* We need platform data */
423 if (!plat || !plat->dma_filter) {
424 dev_info(uap->port.dev, "no DMA platform data\n");
425 return;
426 }
427
428 /* Try to acquire a generic DMA engine slave TX channel */
429 dma_cap_zero(mask);
430 dma_cap_set(DMA_SLAVE, mask);
431
432 chan = dma_request_channel(mask, plat->dma_filter,
433 plat->dma_tx_param);
434 if (!chan) {
435 dev_err(uap->port.dev, "no TX DMA channel!\n");
436 return;
437 }
438 }
439
440 dmaengine_slave_config(chan, &tx_conf);
441 uap->dmatx.chan = chan;
442
443 dev_info(uap->port.dev, "DMA channel TX %s\n",
444 dma_chan_name(uap->dmatx.chan));
445
446 /* Optionally make use of an RX channel as well */
447 chan = dma_request_slave_channel(dev, "rx");
448
449 if (!chan && plat && plat->dma_rx_param) {
450 chan = dma_request_channel(mask, plat->dma_filter, plat->dma_rx_param);
451
452 if (!chan) {
453 dev_err(uap->port.dev, "no RX DMA channel!\n");
454 return;
455 }
456 }
457
458 if (chan) {
459 struct dma_slave_config rx_conf = {
460 .src_addr = uap->port.mapbase +
461 pl011_reg_to_offset(uap, REG_DR),
462 .src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
463 .direction = DMA_DEV_TO_MEM,
464 .src_maxburst = uap->fifosize >> 2,
465 .device_fc = false,
466 };
467 struct dma_slave_caps caps;
468
469 /*
470 * Some DMA controllers provide information on their capabilities.
471 * If the controller does, check for suitable residue processing
472 * otherwise assime all is well.
473 */
474 if (0 == dma_get_slave_caps(chan, &caps)) {
475 if (caps.residue_granularity ==
476 DMA_RESIDUE_GRANULARITY_DESCRIPTOR) {
477 dma_release_channel(chan);
478 dev_info(uap->port.dev,
479 "RX DMA disabled - no residue processing\n");
480 return;
481 }
482 }
483 dmaengine_slave_config(chan, &rx_conf);
484 uap->dmarx.chan = chan;
485
486 uap->dmarx.auto_poll_rate = false;
487 if (plat && plat->dma_rx_poll_enable) {
488 /* Set poll rate if specified. */
489 if (plat->dma_rx_poll_rate) {
490 uap->dmarx.auto_poll_rate = false;
491 uap->dmarx.poll_rate = plat->dma_rx_poll_rate;
492 } else {
493 /*
494 * 100 ms defaults to poll rate if not
495 * specified. This will be adjusted with
496 * the baud rate at set_termios.
497 */
498 uap->dmarx.auto_poll_rate = true;
499 uap->dmarx.poll_rate = 100;
500 }
501 /* 3 secs defaults poll_timeout if not specified. */
502 if (plat->dma_rx_poll_timeout)
503 uap->dmarx.poll_timeout =
504 plat->dma_rx_poll_timeout;
505 else
506 uap->dmarx.poll_timeout = 3000;
507 } else if (!plat && dev->of_node) {
508 uap->dmarx.auto_poll_rate = of_property_read_bool(
509 dev->of_node, "auto-poll");
510 if (uap->dmarx.auto_poll_rate) {
511 u32 x;
512
513 if (0 == of_property_read_u32(dev->of_node,
514 "poll-rate-ms", &x))
515 uap->dmarx.poll_rate = x;
516 else
517 uap->dmarx.poll_rate = 100;
518 if (0 == of_property_read_u32(dev->of_node,
519 "poll-timeout-ms", &x))
520 uap->dmarx.poll_timeout = x;
521 else
522 uap->dmarx.poll_timeout = 3000;
523 }
524 }
525 dev_info(uap->port.dev, "DMA channel RX %s\n",
526 dma_chan_name(uap->dmarx.chan));
527 }
528}
529
530static void pl011_dma_remove(struct uart_amba_port *uap)
531{
532 if (uap->dmatx.chan)
533 dma_release_channel(uap->dmatx.chan);
534 if (uap->dmarx.chan)
535 dma_release_channel(uap->dmarx.chan);
536}
537
538/* Forward declare these for the refill routine */
539static int pl011_dma_tx_refill(struct uart_amba_port *uap);
540static void pl011_start_tx_pio(struct uart_amba_port *uap);
541
542/*
543 * The current DMA TX buffer has been sent.
544 * Try to queue up another DMA buffer.
545 */
546static void pl011_dma_tx_callback(void *data)
547{
548 struct uart_amba_port *uap = data;
549 struct pl011_dmatx_data *dmatx = &uap->dmatx;
550 unsigned long flags;
551 u16 dmacr;
552
553 spin_lock_irqsave(&uap->port.lock, flags);
554 if (uap->dmatx.queued)
555 dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1,
556 DMA_TO_DEVICE);
557
558 dmacr = uap->dmacr;
559 uap->dmacr = dmacr & ~UART011_TXDMAE;
560 pl011_write(uap->dmacr, uap, REG_DMACR);
561
562 /*
563 * If TX DMA was disabled, it means that we've stopped the DMA for
564 * some reason (eg, XOFF received, or we want to send an X-char.)
565 *
566 * Note: we need to be careful here of a potential race between DMA
567 * and the rest of the driver - if the driver disables TX DMA while
568 * a TX buffer completing, we must update the tx queued status to
569 * get further refills (hence we check dmacr).
570 */
571 if (!(dmacr & UART011_TXDMAE) || uart_tx_stopped(&uap->port) ||
572 uart_circ_empty(&uap->port.state->xmit)) {
573 uap->dmatx.queued = false;
574 spin_unlock_irqrestore(&uap->port.lock, flags);
575 return;
576 }
577
578 if (pl011_dma_tx_refill(uap) <= 0)
579 /*
580 * We didn't queue a DMA buffer for some reason, but we
581 * have data pending to be sent. Re-enable the TX IRQ.
582 */
583 pl011_start_tx_pio(uap);
584
585 spin_unlock_irqrestore(&uap->port.lock, flags);
586}
587
588/*
589 * Try to refill the TX DMA buffer.
590 * Locking: called with port lock held and IRQs disabled.
591 * Returns:
592 * 1 if we queued up a TX DMA buffer.
593 * 0 if we didn't want to handle this by DMA
594 * <0 on error
595 */
596static int pl011_dma_tx_refill(struct uart_amba_port *uap)
597{
598 struct pl011_dmatx_data *dmatx = &uap->dmatx;
599 struct dma_chan *chan = dmatx->chan;
600 struct dma_device *dma_dev = chan->device;
601 struct dma_async_tx_descriptor *desc;
602 struct circ_buf *xmit = &uap->port.state->xmit;
603 unsigned int count;
604
605 /*
606 * Try to avoid the overhead involved in using DMA if the
607 * transaction fits in the first half of the FIFO, by using
608 * the standard interrupt handling. This ensures that we
609 * issue a uart_write_wakeup() at the appropriate time.
610 */
611 count = uart_circ_chars_pending(xmit);
612 if (count < (uap->fifosize >> 1)) {
613 uap->dmatx.queued = false;
614 return 0;
615 }
616
617 /*
618 * Bodge: don't send the last character by DMA, as this
619 * will prevent XON from notifying us to restart DMA.
620 */
621 count -= 1;
622
623 /* Else proceed to copy the TX chars to the DMA buffer and fire DMA */
624 if (count > PL011_DMA_BUFFER_SIZE)
625 count = PL011_DMA_BUFFER_SIZE;
626
627 if (xmit->tail < xmit->head)
628 memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], count);
629 else {
630 size_t first = UART_XMIT_SIZE - xmit->tail;
631 size_t second;
632
633 if (first > count)
634 first = count;
635 second = count - first;
636
637 memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], first);
638 if (second)
639 memcpy(&dmatx->buf[first], &xmit->buf[0], second);
640 }
641
642 dmatx->sg.length = count;
643
644 if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) {
645 uap->dmatx.queued = false;
646 dev_dbg(uap->port.dev, "unable to map TX DMA\n");
647 return -EBUSY;
648 }
649
650 desc = dmaengine_prep_slave_sg(chan, &dmatx->sg, 1, DMA_MEM_TO_DEV,
651 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
652 if (!desc) {
653 dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE);
654 uap->dmatx.queued = false;
655 /*
656 * If DMA cannot be used right now, we complete this
657 * transaction via IRQ and let the TTY layer retry.
658 */
659 dev_dbg(uap->port.dev, "TX DMA busy\n");
660 return -EBUSY;
661 }
662
663 /* Some data to go along to the callback */
664 desc->callback = pl011_dma_tx_callback;
665 desc->callback_param = uap;
666
667 /* All errors should happen at prepare time */
668 dmaengine_submit(desc);
669
670 /* Fire the DMA transaction */
671 dma_dev->device_issue_pending(chan);
672
673 uap->dmacr |= UART011_TXDMAE;
674 pl011_write(uap->dmacr, uap, REG_DMACR);
675 uap->dmatx.queued = true;
676
677 /*
678 * Now we know that DMA will fire, so advance the ring buffer
679 * with the stuff we just dispatched.
680 */
681 xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
682 uap->port.icount.tx += count;
683
684 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
685 uart_write_wakeup(&uap->port);
686
687 return 1;
688}
689
690/*
691 * We received a transmit interrupt without a pending X-char but with
692 * pending characters.
693 * Locking: called with port lock held and IRQs disabled.
694 * Returns:
695 * false if we want to use PIO to transmit
696 * true if we queued a DMA buffer
697 */
698static bool pl011_dma_tx_irq(struct uart_amba_port *uap)
699{
700 if (!uap->using_tx_dma)
701 return false;
702
703 /*
704 * If we already have a TX buffer queued, but received a
705 * TX interrupt, it will be because we've just sent an X-char.
706 * Ensure the TX DMA is enabled and the TX IRQ is disabled.
707 */
708 if (uap->dmatx.queued) {
709 uap->dmacr |= UART011_TXDMAE;
710 pl011_write(uap->dmacr, uap, REG_DMACR);
711 uap->im &= ~UART011_TXIM;
712 pl011_write(uap->im, uap, REG_IMSC);
713 return true;
714 }
715
716 /*
717 * We don't have a TX buffer queued, so try to queue one.
718 * If we successfully queued a buffer, mask the TX IRQ.
719 */
720 if (pl011_dma_tx_refill(uap) > 0) {
721 uap->im &= ~UART011_TXIM;
722 pl011_write(uap->im, uap, REG_IMSC);
723 return true;
724 }
725 return false;
726}
727
728/*
729 * Stop the DMA transmit (eg, due to received XOFF).
730 * Locking: called with port lock held and IRQs disabled.
731 */
732static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
733{
734 if (uap->dmatx.queued) {
735 uap->dmacr &= ~UART011_TXDMAE;
736 pl011_write(uap->dmacr, uap, REG_DMACR);
737 }
738}
739
740/*
741 * Try to start a DMA transmit, or in the case of an XON/OFF
742 * character queued for send, try to get that character out ASAP.
743 * Locking: called with port lock held and IRQs disabled.
744 * Returns:
745 * false if we want the TX IRQ to be enabled
746 * true if we have a buffer queued
747 */
748static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
749{
750 u16 dmacr;
751
752 if (!uap->using_tx_dma)
753 return false;
754
755 if (!uap->port.x_char) {
756 /* no X-char, try to push chars out in DMA mode */
757 bool ret = true;
758
759 if (!uap->dmatx.queued) {
760 if (pl011_dma_tx_refill(uap) > 0) {
761 uap->im &= ~UART011_TXIM;
762 pl011_write(uap->im, uap, REG_IMSC);
763 } else
764 ret = false;
765 } else if (!(uap->dmacr & UART011_TXDMAE)) {
766 uap->dmacr |= UART011_TXDMAE;
767 pl011_write(uap->dmacr, uap, REG_DMACR);
768 }
769 return ret;
770 }
771
772 /*
773 * We have an X-char to send. Disable DMA to prevent it loading
774 * the TX fifo, and then see if we can stuff it into the FIFO.
775 */
776 dmacr = uap->dmacr;
777 uap->dmacr &= ~UART011_TXDMAE;
778 pl011_write(uap->dmacr, uap, REG_DMACR);
779
780 if (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) {
781 /*
782 * No space in the FIFO, so enable the transmit interrupt
783 * so we know when there is space. Note that once we've
784 * loaded the character, we should just re-enable DMA.
785 */
786 return false;
787 }
788
789 pl011_write(uap->port.x_char, uap, REG_DR);
790 uap->port.icount.tx++;
791 uap->port.x_char = 0;
792
793 /* Success - restore the DMA state */
794 uap->dmacr = dmacr;
795 pl011_write(dmacr, uap, REG_DMACR);
796
797 return true;
798}
799
800/*
801 * Flush the transmit buffer.
802 * Locking: called with port lock held and IRQs disabled.
803 */
804static void pl011_dma_flush_buffer(struct uart_port *port)
805__releases(&uap->port.lock)
806__acquires(&uap->port.lock)
807{
808 struct uart_amba_port *uap =
809 container_of(port, struct uart_amba_port, port);
810
811 if (!uap->using_tx_dma)
812 return;
813
814 /* Avoid deadlock with the DMA engine callback */
815 spin_unlock(&uap->port.lock);
816 dmaengine_terminate_all(uap->dmatx.chan);
817 spin_lock(&uap->port.lock);
818 if (uap->dmatx.queued) {
819 dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
820 DMA_TO_DEVICE);
821 uap->dmatx.queued = false;
822 uap->dmacr &= ~UART011_TXDMAE;
823 pl011_write(uap->dmacr, uap, REG_DMACR);
824 }
825}
826
827static void pl011_dma_rx_callback(void *data);
828
829static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
830{
831 struct dma_chan *rxchan = uap->dmarx.chan;
832 struct pl011_dmarx_data *dmarx = &uap->dmarx;
833 struct dma_async_tx_descriptor *desc;
834 struct pl011_sgbuf *sgbuf;
835
836 if (!rxchan)
837 return -EIO;
838
839 /* Start the RX DMA job */
840 sgbuf = uap->dmarx.use_buf_b ?
841 &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
842 desc = dmaengine_prep_slave_sg(rxchan, &sgbuf->sg, 1,
843 DMA_DEV_TO_MEM,
844 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
845 /*
846 * If the DMA engine is busy and cannot prepare a
847 * channel, no big deal, the driver will fall back
848 * to interrupt mode as a result of this error code.
849 */
850 if (!desc) {
851 uap->dmarx.running = false;
852 dmaengine_terminate_all(rxchan);
853 return -EBUSY;
854 }
855
856 /* Some data to go along to the callback */
857 desc->callback = pl011_dma_rx_callback;
858 desc->callback_param = uap;
859 dmarx->cookie = dmaengine_submit(desc);
860 dma_async_issue_pending(rxchan);
861
862 uap->dmacr |= UART011_RXDMAE;
863 pl011_write(uap->dmacr, uap, REG_DMACR);
864 uap->dmarx.running = true;
865
866 uap->im &= ~UART011_RXIM;
867 pl011_write(uap->im, uap, REG_IMSC);
868
869 return 0;
870}
871
872/*
873 * This is called when either the DMA job is complete, or
874 * the FIFO timeout interrupt occurred. This must be called
875 * with the port spinlock uap->port.lock held.
876 */
877static void pl011_dma_rx_chars(struct uart_amba_port *uap,
878 u32 pending, bool use_buf_b,
879 bool readfifo)
880{
881 struct tty_port *port = &uap->port.state->port;
882 struct pl011_sgbuf *sgbuf = use_buf_b ?
883 &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
884 int dma_count = 0;
885 u32 fifotaken = 0; /* only used for vdbg() */
886
887 struct pl011_dmarx_data *dmarx = &uap->dmarx;
888 int dmataken = 0;
889
890 if (uap->dmarx.poll_rate) {
891 /* The data can be taken by polling */
892 dmataken = sgbuf->sg.length - dmarx->last_residue;
893 /* Recalculate the pending size */
894 if (pending >= dmataken)
895 pending -= dmataken;
896 }
897
898 /* Pick the remain data from the DMA */
899 if (pending) {
900
901 /*
902 * First take all chars in the DMA pipe, then look in the FIFO.
903 * Note that tty_insert_flip_buf() tries to take as many chars
904 * as it can.
905 */
906 dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken,
907 pending);
908
909 uap->port.icount.rx += dma_count;
910 if (dma_count < pending)
911 dev_warn(uap->port.dev,
912 "couldn't insert all characters (TTY is full?)\n");
913 }
914
915 /* Reset the last_residue for Rx DMA poll */
916 if (uap->dmarx.poll_rate)
917 dmarx->last_residue = sgbuf->sg.length;
918
919 /*
920 * Only continue with trying to read the FIFO if all DMA chars have
921 * been taken first.
922 */
923 if (dma_count == pending && readfifo) {
924 /* Clear any error flags */
925 pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS |
926 UART011_FEIS, uap, REG_ICR);
927
928 /*
929 * If we read all the DMA'd characters, and we had an
930 * incomplete buffer, that could be due to an rx error, or
931 * maybe we just timed out. Read any pending chars and check
932 * the error status.
933 *
934 * Error conditions will only occur in the FIFO, these will
935 * trigger an immediate interrupt and stop the DMA job, so we
936 * will always find the error in the FIFO, never in the DMA
937 * buffer.
938 */
939 fifotaken = pl011_fifo_to_tty(uap);
940 }
941
942 spin_unlock(&uap->port.lock);
943 dev_vdbg(uap->port.dev,
944 "Took %d chars from DMA buffer and %d chars from the FIFO\n",
945 dma_count, fifotaken);
946 tty_flip_buffer_push(port);
947 spin_lock(&uap->port.lock);
948}
949
950static void pl011_dma_rx_irq(struct uart_amba_port *uap)
951{
952 struct pl011_dmarx_data *dmarx = &uap->dmarx;
953 struct dma_chan *rxchan = dmarx->chan;
954 struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
955 &dmarx->sgbuf_b : &dmarx->sgbuf_a;
956 size_t pending;
957 struct dma_tx_state state;
958 enum dma_status dmastat;
959
960 /*
961 * Pause the transfer so we can trust the current counter,
962 * do this before we pause the PL011 block, else we may
963 * overflow the FIFO.
964 */
965 if (dmaengine_pause(rxchan))
966 dev_err(uap->port.dev, "unable to pause DMA transfer\n");
967 dmastat = rxchan->device->device_tx_status(rxchan,
968 dmarx->cookie, &state);
969 if (dmastat != DMA_PAUSED)
970 dev_err(uap->port.dev, "unable to pause DMA transfer\n");
971
972 /* Disable RX DMA - incoming data will wait in the FIFO */
973 uap->dmacr &= ~UART011_RXDMAE;
974 pl011_write(uap->dmacr, uap, REG_DMACR);
975 uap->dmarx.running = false;
976
977 pending = sgbuf->sg.length - state.residue;
978 BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
979 /* Then we terminate the transfer - we now know our residue */
980 dmaengine_terminate_all(rxchan);
981
982 /*
983 * This will take the chars we have so far and insert
984 * into the framework.
985 */
986 pl011_dma_rx_chars(uap, pending, dmarx->use_buf_b, true);
987
988 /* Switch buffer & re-trigger DMA job */
989 dmarx->use_buf_b = !dmarx->use_buf_b;
990 if (pl011_dma_rx_trigger_dma(uap)) {
991 dev_dbg(uap->port.dev, "could not retrigger RX DMA job "
992 "fall back to interrupt mode\n");
993 uap->im |= UART011_RXIM;
994 pl011_write(uap->im, uap, REG_IMSC);
995 }
996}
997
998static void pl011_dma_rx_callback(void *data)
999{
1000 struct uart_amba_port *uap = data;
1001 struct pl011_dmarx_data *dmarx = &uap->dmarx;
1002 struct dma_chan *rxchan = dmarx->chan;
1003 bool lastbuf = dmarx->use_buf_b;
1004 struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
1005 &dmarx->sgbuf_b : &dmarx->sgbuf_a;
1006 size_t pending;
1007 struct dma_tx_state state;
1008 int ret;
1009
1010 /*
1011 * This completion interrupt occurs typically when the
1012 * RX buffer is totally stuffed but no timeout has yet
1013 * occurred. When that happens, we just want the RX
1014 * routine to flush out the secondary DMA buffer while
1015 * we immediately trigger the next DMA job.
1016 */
1017 spin_lock_irq(&uap->port.lock);
1018 /*
1019 * Rx data can be taken by the UART interrupts during
1020 * the DMA irq handler. So we check the residue here.
1021 */
1022 rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state);
1023 pending = sgbuf->sg.length - state.residue;
1024 BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
1025 /* Then we terminate the transfer - we now know our residue */
1026 dmaengine_terminate_all(rxchan);
1027
1028 uap->dmarx.running = false;
1029 dmarx->use_buf_b = !lastbuf;
1030 ret = pl011_dma_rx_trigger_dma(uap);
1031
1032 pl011_dma_rx_chars(uap, pending, lastbuf, false);
1033 spin_unlock_irq(&uap->port.lock);
1034 /*
1035 * Do this check after we picked the DMA chars so we don't
1036 * get some IRQ immediately from RX.
1037 */
1038 if (ret) {
1039 dev_dbg(uap->port.dev, "could not retrigger RX DMA job "
1040 "fall back to interrupt mode\n");
1041 uap->im |= UART011_RXIM;
1042 pl011_write(uap->im, uap, REG_IMSC);
1043 }
1044}
1045
1046/*
1047 * Stop accepting received characters, when we're shutting down or
1048 * suspending this port.
1049 * Locking: called with port lock held and IRQs disabled.
1050 */
1051static inline void pl011_dma_rx_stop(struct uart_amba_port *uap)
1052{
1053 /* FIXME. Just disable the DMA enable */
1054 uap->dmacr &= ~UART011_RXDMAE;
1055 pl011_write(uap->dmacr, uap, REG_DMACR);
1056}
1057
1058/*
1059 * Timer handler for Rx DMA polling.
1060 * Every polling, It checks the residue in the dma buffer and transfer
1061 * data to the tty. Also, last_residue is updated for the next polling.
1062 */
1063static void pl011_dma_rx_poll(unsigned long args)
1064{
1065 struct uart_amba_port *uap = (struct uart_amba_port *)args;
1066 struct tty_port *port = &uap->port.state->port;
1067 struct pl011_dmarx_data *dmarx = &uap->dmarx;
1068 struct dma_chan *rxchan = uap->dmarx.chan;
1069 unsigned long flags = 0;
1070 unsigned int dmataken = 0;
1071 unsigned int size = 0;
1072 struct pl011_sgbuf *sgbuf;
1073 int dma_count;
1074 struct dma_tx_state state;
1075
1076 sgbuf = dmarx->use_buf_b ? &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
1077 rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state);
1078 if (likely(state.residue < dmarx->last_residue)) {
1079 dmataken = sgbuf->sg.length - dmarx->last_residue;
1080 size = dmarx->last_residue - state.residue;
1081 dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken,
1082 size);
1083 if (dma_count == size)
1084 dmarx->last_residue = state.residue;
1085 dmarx->last_jiffies = jiffies;
1086 }
1087 tty_flip_buffer_push(port);
1088
1089 /*
1090 * If no data is received in poll_timeout, the driver will fall back
1091 * to interrupt mode. We will retrigger DMA at the first interrupt.
1092 */
1093 if (jiffies_to_msecs(jiffies - dmarx->last_jiffies)
1094 > uap->dmarx.poll_timeout) {
1095
1096 spin_lock_irqsave(&uap->port.lock, flags);
1097 pl011_dma_rx_stop(uap);
1098 uap->im |= UART011_RXIM;
1099 pl011_write(uap->im, uap, REG_IMSC);
1100 spin_unlock_irqrestore(&uap->port.lock, flags);
1101
1102 uap->dmarx.running = false;
1103 dmaengine_terminate_all(rxchan);
1104 del_timer(&uap->dmarx.timer);
1105 } else {
1106 mod_timer(&uap->dmarx.timer,
1107 jiffies + msecs_to_jiffies(uap->dmarx.poll_rate));
1108 }
1109}
1110
1111static void pl011_dma_startup(struct uart_amba_port *uap)
1112{
1113 int ret;
1114
1115 if (!uap->dma_probed)
1116 pl011_dma_probe(uap);
1117
1118 if (!uap->dmatx.chan)
1119 return;
1120
1121 uap->dmatx.buf = kmalloc(PL011_DMA_BUFFER_SIZE, GFP_KERNEL | __GFP_DMA);
1122 if (!uap->dmatx.buf) {
1123 dev_err(uap->port.dev, "no memory for DMA TX buffer\n");
1124 uap->port.fifosize = uap->fifosize;
1125 return;
1126 }
1127
1128 sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE);
1129
1130 /* The DMA buffer is now the FIFO the TTY subsystem can use */
1131 uap->port.fifosize = PL011_DMA_BUFFER_SIZE;
1132 uap->using_tx_dma = true;
1133
1134 if (!uap->dmarx.chan)
1135 goto skip_rx;
1136
1137 /* Allocate and map DMA RX buffers */
1138 ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
1139 DMA_FROM_DEVICE);
1140 if (ret) {
1141 dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
1142 "RX buffer A", ret);
1143 goto skip_rx;
1144 }
1145
1146 ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_b,
1147 DMA_FROM_DEVICE);
1148 if (ret) {
1149 dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
1150 "RX buffer B", ret);
1151 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
1152 DMA_FROM_DEVICE);
1153 goto skip_rx;
1154 }
1155
1156 uap->using_rx_dma = true;
1157
1158skip_rx:
1159 /* Turn on DMA error (RX/TX will be enabled on demand) */
1160 uap->dmacr |= UART011_DMAONERR;
1161 pl011_write(uap->dmacr, uap, REG_DMACR);
1162
1163 /*
1164 * ST Micro variants has some specific dma burst threshold
1165 * compensation. Set this to 16 bytes, so burst will only
1166 * be issued above/below 16 bytes.
1167 */
1168 if (uap->vendor->dma_threshold)
1169 pl011_write(ST_UART011_DMAWM_RX_16 | ST_UART011_DMAWM_TX_16,
1170 uap, REG_ST_DMAWM);
1171
1172 if (uap->using_rx_dma) {
1173 if (pl011_dma_rx_trigger_dma(uap))
1174 dev_dbg(uap->port.dev, "could not trigger initial "
1175 "RX DMA job, fall back to interrupt mode\n");
1176 if (uap->dmarx.poll_rate) {
1177 init_timer(&(uap->dmarx.timer));
1178 uap->dmarx.timer.function = pl011_dma_rx_poll;
1179 uap->dmarx.timer.data = (unsigned long)uap;
1180 mod_timer(&uap->dmarx.timer,
1181 jiffies +
1182 msecs_to_jiffies(uap->dmarx.poll_rate));
1183 uap->dmarx.last_residue = PL011_DMA_BUFFER_SIZE;
1184 uap->dmarx.last_jiffies = jiffies;
1185 }
1186 }
1187}
1188
1189static void pl011_dma_shutdown(struct uart_amba_port *uap)
1190{
1191 if (!(uap->using_tx_dma || uap->using_rx_dma))
1192 return;
1193
1194 /* Disable RX and TX DMA */
1195 while (pl011_read(uap, REG_FR) & uap->vendor->fr_busy)
1196 cpu_relax();
1197
1198 spin_lock_irq(&uap->port.lock);
1199 uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE);
1200 pl011_write(uap->dmacr, uap, REG_DMACR);
1201 spin_unlock_irq(&uap->port.lock);
1202
1203 if (uap->using_tx_dma) {
1204 /* In theory, this should already be done by pl011_dma_flush_buffer */
1205 dmaengine_terminate_all(uap->dmatx.chan);
1206 if (uap->dmatx.queued) {
1207 dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
1208 DMA_TO_DEVICE);
1209 uap->dmatx.queued = false;
1210 }
1211
1212 kfree(uap->dmatx.buf);
1213 uap->using_tx_dma = false;
1214 }
1215
1216 if (uap->using_rx_dma) {
1217 dmaengine_terminate_all(uap->dmarx.chan);
1218 /* Clean up the RX DMA */
1219 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a, DMA_FROM_DEVICE);
1220 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_b, DMA_FROM_DEVICE);
1221 if (uap->dmarx.poll_rate)
1222 del_timer_sync(&uap->dmarx.timer);
1223 uap->using_rx_dma = false;
1224 }
1225}
1226
1227static inline bool pl011_dma_rx_available(struct uart_amba_port *uap)
1228{
1229 return uap->using_rx_dma;
1230}
1231
1232static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
1233{
1234 return uap->using_rx_dma && uap->dmarx.running;
1235}
1236
1237#else
1238/* Blank functions if the DMA engine is not available */
1239static inline void pl011_dma_probe(struct uart_amba_port *uap)
1240{
1241}
1242
1243static inline void pl011_dma_remove(struct uart_amba_port *uap)
1244{
1245}
1246
1247static inline void pl011_dma_startup(struct uart_amba_port *uap)
1248{
1249}
1250
1251static inline void pl011_dma_shutdown(struct uart_amba_port *uap)
1252{
1253}
1254
1255static inline bool pl011_dma_tx_irq(struct uart_amba_port *uap)
1256{
1257 return false;
1258}
1259
1260static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
1261{
1262}
1263
1264static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
1265{
1266 return false;
1267}
1268
1269static inline void pl011_dma_rx_irq(struct uart_amba_port *uap)
1270{
1271}
1272
1273static inline void pl011_dma_rx_stop(struct uart_amba_port *uap)
1274{
1275}
1276
1277static inline int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
1278{
1279 return -EIO;
1280}
1281
1282static inline bool pl011_dma_rx_available(struct uart_amba_port *uap)
1283{
1284 return false;
1285}
1286
1287static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
1288{
1289 return false;
1290}
1291
1292#define pl011_dma_flush_buffer NULL
1293#endif
1294
1295static void pl011_stop_tx(struct uart_port *port)
1296{
1297 struct uart_amba_port *uap =
1298 container_of(port, struct uart_amba_port, port);
1299
1300 uap->im &= ~UART011_TXIM;
1301 pl011_write(uap->im, uap, REG_IMSC);
1302 pl011_dma_tx_stop(uap);
1303}
1304
1305static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
1306
1307/* Start TX with programmed I/O only (no DMA) */
1308static void pl011_start_tx_pio(struct uart_amba_port *uap)
1309{
1310 uap->im |= UART011_TXIM;
1311 pl011_write(uap->im, uap, REG_IMSC);
1312 pl011_tx_chars(uap, false);
1313}
1314
1315static void pl011_start_tx(struct uart_port *port)
1316{
1317 struct uart_amba_port *uap =
1318 container_of(port, struct uart_amba_port, port);
1319
1320 if (!pl011_dma_tx_start(uap))
1321 pl011_start_tx_pio(uap);
1322}
1323
1324static void pl011_stop_rx(struct uart_port *port)
1325{
1326 struct uart_amba_port *uap =
1327 container_of(port, struct uart_amba_port, port);
1328
1329 uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
1330 UART011_PEIM|UART011_BEIM|UART011_OEIM);
1331 pl011_write(uap->im, uap, REG_IMSC);
1332
1333 pl011_dma_rx_stop(uap);
1334}
1335
1336static void pl011_enable_ms(struct uart_port *port)
1337{
1338 struct uart_amba_port *uap =
1339 container_of(port, struct uart_amba_port, port);
1340
1341 uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
1342 pl011_write(uap->im, uap, REG_IMSC);
1343}
1344
1345static void pl011_rx_chars(struct uart_amba_port *uap)
1346__releases(&uap->port.lock)
1347__acquires(&uap->port.lock)
1348{
1349 pl011_fifo_to_tty(uap);
1350
1351 spin_unlock(&uap->port.lock);
1352 tty_flip_buffer_push(&uap->port.state->port);
1353 /*
1354 * If we were temporarily out of DMA mode for a while,
1355 * attempt to switch back to DMA mode again.
1356 */
1357 if (pl011_dma_rx_available(uap)) {
1358 if (pl011_dma_rx_trigger_dma(uap)) {
1359 dev_dbg(uap->port.dev, "could not trigger RX DMA job "
1360 "fall back to interrupt mode again\n");
1361 uap->im |= UART011_RXIM;
1362 pl011_write(uap->im, uap, REG_IMSC);
1363 } else {
1364#ifdef CONFIG_DMA_ENGINE
1365 /* Start Rx DMA poll */
1366 if (uap->dmarx.poll_rate) {
1367 uap->dmarx.last_jiffies = jiffies;
1368 uap->dmarx.last_residue = PL011_DMA_BUFFER_SIZE;
1369 mod_timer(&uap->dmarx.timer,
1370 jiffies +
1371 msecs_to_jiffies(uap->dmarx.poll_rate));
1372 }
1373#endif
1374 }
1375 }
1376 spin_lock(&uap->port.lock);
1377}
1378
1379static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
1380 bool from_irq)
1381{
1382 if (unlikely(!from_irq) &&
1383 pl011_read(uap, REG_FR) & UART01x_FR_TXFF)
1384 return false; /* unable to transmit character */
1385
1386 pl011_write(c, uap, REG_DR);
1387 uap->port.icount.tx++;
1388
1389 return true;
1390}
1391
1392static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
1393{
1394 struct circ_buf *xmit = &uap->port.state->xmit;
1395 int count = uap->fifosize >> 1;
1396
1397 if (uap->port.x_char) {
1398 if (!pl011_tx_char(uap, uap->port.x_char, from_irq))
1399 return;
1400 uap->port.x_char = 0;
1401 --count;
1402 }
1403 if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
1404 pl011_stop_tx(&uap->port);
1405 return;
1406 }
1407
1408 /* If we are using DMA mode, try to send some characters. */
1409 if (pl011_dma_tx_irq(uap))
1410 return;
1411
1412 do {
1413 if (likely(from_irq) && count-- == 0)
1414 break;
1415
1416 if (!pl011_tx_char(uap, xmit->buf[xmit->tail], from_irq))
1417 break;
1418
1419 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
1420 } while (!uart_circ_empty(xmit));
1421
1422 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1423 uart_write_wakeup(&uap->port);
1424
1425 if (uart_circ_empty(xmit))
1426 pl011_stop_tx(&uap->port);
1427}
1428
1429static void pl011_modem_status(struct uart_amba_port *uap)
1430{
1431 unsigned int status, delta;
1432
1433 status = pl011_read(uap, REG_FR) & UART01x_FR_MODEM_ANY;
1434
1435 delta = status ^ uap->old_status;
1436 uap->old_status = status;
1437
1438 if (!delta)
1439 return;
1440
1441 if (delta & UART01x_FR_DCD)
1442 uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
1443
1444 if (delta & uap->vendor->fr_dsr)
1445 uap->port.icount.dsr++;
1446
1447 if (delta & uap->vendor->fr_cts)
1448 uart_handle_cts_change(&uap->port,
1449 status & uap->vendor->fr_cts);
1450
1451 wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
1452}
1453
1454static void check_apply_cts_event_workaround(struct uart_amba_port *uap)
1455{
1456 unsigned int dummy_read;
1457
1458 if (!uap->vendor->cts_event_workaround)
1459 return;
1460
1461 /* workaround to make sure that all bits are unlocked.. */
1462 pl011_write(0x00, uap, REG_ICR);
1463
1464 /*
1465 * WA: introduce 26ns(1 uart clk) delay before W1C;
1466 * single apb access will incur 2 pclk(133.12Mhz) delay,
1467 * so add 2 dummy reads
1468 */
1469 dummy_read = pl011_read(uap, REG_ICR);
1470 dummy_read = pl011_read(uap, REG_ICR);
1471}
1472
1473static irqreturn_t pl011_int(int irq, void *dev_id)
1474{
1475 struct uart_amba_port *uap = dev_id;
1476 unsigned long flags;
1477 unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
1478 u16 imsc;
1479 int handled = 0;
1480
1481 spin_lock_irqsave(&uap->port.lock, flags);
1482 imsc = pl011_read(uap, REG_IMSC);
1483 status = pl011_read(uap, REG_RIS) & imsc;
1484 if (status) {
1485 do {
1486 check_apply_cts_event_workaround(uap);
1487
1488 pl011_write(status & ~(UART011_TXIS|UART011_RTIS|
1489 UART011_RXIS),
1490 uap, REG_ICR);
1491
1492 if (status & (UART011_RTIS|UART011_RXIS)) {
1493 if (pl011_dma_rx_running(uap))
1494 pl011_dma_rx_irq(uap);
1495 else
1496 pl011_rx_chars(uap);
1497 }
1498 if (status & (UART011_DSRMIS|UART011_DCDMIS|
1499 UART011_CTSMIS|UART011_RIMIS))
1500 pl011_modem_status(uap);
1501 if (status & UART011_TXIS)
1502 pl011_tx_chars(uap, true);
1503
1504 if (pass_counter-- == 0)
1505 break;
1506
1507 status = pl011_read(uap, REG_RIS) & imsc;
1508 } while (status != 0);
1509 handled = 1;
1510 }
1511
1512 spin_unlock_irqrestore(&uap->port.lock, flags);
1513
1514 return IRQ_RETVAL(handled);
1515}
1516
1517static unsigned int pl011_tx_empty(struct uart_port *port)
1518{
1519 struct uart_amba_port *uap =
1520 container_of(port, struct uart_amba_port, port);
1521 unsigned int status = pl011_read(uap, REG_FR);
1522 return status & (uap->vendor->fr_busy | UART01x_FR_TXFF) ?
1523 0 : TIOCSER_TEMT;
1524}
1525
1526static unsigned int pl011_get_mctrl(struct uart_port *port)
1527{
1528 struct uart_amba_port *uap =
1529 container_of(port, struct uart_amba_port, port);
1530 unsigned int result = 0;
1531 unsigned int status = pl011_read(uap, REG_FR);
1532
1533#define TIOCMBIT(uartbit, tiocmbit) \
1534 if (status & uartbit) \
1535 result |= tiocmbit
1536
1537 TIOCMBIT(UART01x_FR_DCD, TIOCM_CAR);
1538 TIOCMBIT(uap->vendor->fr_dsr, TIOCM_DSR);
1539 TIOCMBIT(uap->vendor->fr_cts, TIOCM_CTS);
1540 TIOCMBIT(uap->vendor->fr_ri, TIOCM_RNG);
1541#undef TIOCMBIT
1542 return result;
1543}
1544
1545static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
1546{
1547 struct uart_amba_port *uap =
1548 container_of(port, struct uart_amba_port, port);
1549 unsigned int cr;
1550
1551 cr = pl011_read(uap, REG_CR);
1552
1553#define TIOCMBIT(tiocmbit, uartbit) \
1554 if (mctrl & tiocmbit) \
1555 cr |= uartbit; \
1556 else \
1557 cr &= ~uartbit
1558
1559 TIOCMBIT(TIOCM_RTS, UART011_CR_RTS);
1560 TIOCMBIT(TIOCM_DTR, UART011_CR_DTR);
1561 TIOCMBIT(TIOCM_OUT1, UART011_CR_OUT1);
1562 TIOCMBIT(TIOCM_OUT2, UART011_CR_OUT2);
1563 TIOCMBIT(TIOCM_LOOP, UART011_CR_LBE);
1564
1565 if (uap->autorts) {
1566 /* We need to disable auto-RTS if we want to turn RTS off */
1567 TIOCMBIT(TIOCM_RTS, UART011_CR_RTSEN);
1568 }
1569#undef TIOCMBIT
1570
1571 pl011_write(cr, uap, REG_CR);
1572}
1573
1574static void pl011_break_ctl(struct uart_port *port, int break_state)
1575{
1576 struct uart_amba_port *uap =
1577 container_of(port, struct uart_amba_port, port);
1578 unsigned long flags;
1579 unsigned int lcr_h;
1580
1581 spin_lock_irqsave(&uap->port.lock, flags);
1582 lcr_h = pl011_read(uap, REG_LCRH_TX);
1583 if (break_state == -1)
1584 lcr_h |= UART01x_LCRH_BRK;
1585 else
1586 lcr_h &= ~UART01x_LCRH_BRK;
1587 pl011_write(lcr_h, uap, REG_LCRH_TX);
1588 spin_unlock_irqrestore(&uap->port.lock, flags);
1589}
1590
1591#ifdef CONFIG_CONSOLE_POLL
1592
1593static void pl011_quiesce_irqs(struct uart_port *port)
1594{
1595 struct uart_amba_port *uap =
1596 container_of(port, struct uart_amba_port, port);
1597
1598 pl011_write(pl011_read(uap, REG_MIS), uap, REG_ICR);
1599 /*
1600 * There is no way to clear TXIM as this is "ready to transmit IRQ", so
1601 * we simply mask it. start_tx() will unmask it.
1602 *
1603 * Note we can race with start_tx(), and if the race happens, the
1604 * polling user might get another interrupt just after we clear it.
1605 * But it should be OK and can happen even w/o the race, e.g.
1606 * controller immediately got some new data and raised the IRQ.
1607 *
1608 * And whoever uses polling routines assumes that it manages the device
1609 * (including tx queue), so we're also fine with start_tx()'s caller
1610 * side.
1611 */
1612 pl011_write(pl011_read(uap, REG_IMSC) & ~UART011_TXIM, uap,
1613 REG_IMSC);
1614}
1615
1616static int pl011_get_poll_char(struct uart_port *port)
1617{
1618 struct uart_amba_port *uap =
1619 container_of(port, struct uart_amba_port, port);
1620 unsigned int status;
1621
1622 /*
1623 * The caller might need IRQs lowered, e.g. if used with KDB NMI
1624 * debugger.
1625 */
1626 pl011_quiesce_irqs(port);
1627
1628 status = pl011_read(uap, REG_FR);
1629 if (status & UART01x_FR_RXFE)
1630 return NO_POLL_CHAR;
1631
1632 return pl011_read(uap, REG_DR);
1633}
1634
1635static void pl011_put_poll_char(struct uart_port *port,
1636 unsigned char ch)
1637{
1638 struct uart_amba_port *uap =
1639 container_of(port, struct uart_amba_port, port);
1640
1641 while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF)
1642 cpu_relax();
1643
1644 pl011_write(ch, uap, REG_DR);
1645}
1646
1647#endif /* CONFIG_CONSOLE_POLL */
1648
1649static int pl011_hwinit(struct uart_port *port)
1650{
1651 struct uart_amba_port *uap =
1652 container_of(port, struct uart_amba_port, port);
1653 int retval;
1654
1655 /* Optionaly enable pins to be muxed in and configured */
1656 pinctrl_pm_select_default_state(port->dev);
1657
1658 /*
1659 * Try to enable the clock producer.
1660 */
1661 retval = clk_prepare_enable(uap->clk);
1662 if (retval)
1663 return retval;
1664
1665 uap->port.uartclk = clk_get_rate(uap->clk);
1666
1667 /* Clear pending error and receive interrupts */
1668 pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS |
1669 UART011_FEIS | UART011_RTIS | UART011_RXIS,
1670 uap, REG_ICR);
1671
1672 /*
1673 * Save interrupts enable mask, and enable RX interrupts in case if
1674 * the interrupt is used for NMI entry.
1675 */
1676 uap->im = pl011_read(uap, REG_IMSC);
1677 pl011_write(UART011_RTIM | UART011_RXIM, uap, REG_IMSC);
1678
1679 if (dev_get_platdata(uap->port.dev)) {
1680 struct amba_pl011_data *plat;
1681
1682 plat = dev_get_platdata(uap->port.dev);
1683 if (plat->init)
1684 plat->init();
1685 }
1686 return 0;
1687}
1688
1689static bool pl011_split_lcrh(const struct uart_amba_port *uap)
1690{
1691 return pl011_reg_to_offset(uap, REG_LCRH_RX) !=
1692 pl011_reg_to_offset(uap, REG_LCRH_TX);
1693}
1694
1695static void pl011_write_lcr_h(struct uart_amba_port *uap, unsigned int lcr_h)
1696{
1697 pl011_write(lcr_h, uap, REG_LCRH_RX);
1698 if (pl011_split_lcrh(uap)) {
1699 int i;
1700 /*
1701 * Wait 10 PCLKs before writing LCRH_TX register,
1702 * to get this delay write read only register 10 times
1703 */
1704 for (i = 0; i < 10; ++i)
1705 pl011_write(0xff, uap, REG_MIS);
1706 pl011_write(lcr_h, uap, REG_LCRH_TX);
1707 }
1708}
1709
1710static int pl011_allocate_irq(struct uart_amba_port *uap)
1711{
1712 pl011_write(uap->im, uap, REG_IMSC);
1713
1714 return request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap);
1715}
1716
1717/*
1718 * Enable interrupts, only timeouts when using DMA
1719 * if initial RX DMA job failed, start in interrupt mode
1720 * as well.
1721 */
1722static void pl011_enable_interrupts(struct uart_amba_port *uap)
1723{
1724 spin_lock_irq(&uap->port.lock);
1725
1726 /* Clear out any spuriously appearing RX interrupts */
1727 pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR);
1728 uap->im = UART011_RTIM;
1729 if (!pl011_dma_rx_running(uap))
1730 uap->im |= UART011_RXIM;
1731 pl011_write(uap->im, uap, REG_IMSC);
1732 spin_unlock_irq(&uap->port.lock);
1733}
1734
1735static int pl011_startup(struct uart_port *port)
1736{
1737 struct uart_amba_port *uap =
1738 container_of(port, struct uart_amba_port, port);
1739 unsigned int cr;
1740 int retval;
1741
1742 retval = pl011_hwinit(port);
1743 if (retval)
1744 goto clk_dis;
1745
1746 retval = pl011_allocate_irq(uap);
1747 if (retval)
1748 goto clk_dis;
1749
1750 pl011_write(uap->vendor->ifls, uap, REG_IFLS);
1751
1752 spin_lock_irq(&uap->port.lock);
1753
1754 /* restore RTS and DTR */
1755 cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR);
1756 cr |= UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
1757 pl011_write(cr, uap, REG_CR);
1758
1759 spin_unlock_irq(&uap->port.lock);
1760
1761 /*
1762 * initialise the old status of the modem signals
1763 */
1764 uap->old_status = pl011_read(uap, REG_FR) & UART01x_FR_MODEM_ANY;
1765
1766 /* Startup DMA */
1767 pl011_dma_startup(uap);
1768
1769 pl011_enable_interrupts(uap);
1770
1771 return 0;
1772
1773 clk_dis:
1774 clk_disable_unprepare(uap->clk);
1775 return retval;
1776}
1777
1778static int sbsa_uart_startup(struct uart_port *port)
1779{
1780 struct uart_amba_port *uap =
1781 container_of(port, struct uart_amba_port, port);
1782 int retval;
1783
1784 retval = pl011_hwinit(port);
1785 if (retval)
1786 return retval;
1787
1788 retval = pl011_allocate_irq(uap);
1789 if (retval)
1790 return retval;
1791
1792 /* The SBSA UART does not support any modem status lines. */
1793 uap->old_status = 0;
1794
1795 pl011_enable_interrupts(uap);
1796
1797 return 0;
1798}
1799
1800static void pl011_shutdown_channel(struct uart_amba_port *uap,
1801 unsigned int lcrh)
1802{
1803 unsigned long val;
1804
1805 val = pl011_read(uap, lcrh);
1806 val &= ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN);
1807 pl011_write(val, uap, lcrh);
1808}
1809
1810/*
1811 * disable the port. It should not disable RTS and DTR.
1812 * Also RTS and DTR state should be preserved to restore
1813 * it during startup().
1814 */
1815static void pl011_disable_uart(struct uart_amba_port *uap)
1816{
1817 unsigned int cr;
1818
1819 uap->autorts = false;
1820 spin_lock_irq(&uap->port.lock);
1821 cr = pl011_read(uap, REG_CR);
1822 uap->old_cr = cr;
1823 cr &= UART011_CR_RTS | UART011_CR_DTR;
1824 cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
1825 pl011_write(cr, uap, REG_CR);
1826 spin_unlock_irq(&uap->port.lock);
1827
1828 /*
1829 * disable break condition and fifos
1830 */
1831 pl011_shutdown_channel(uap, REG_LCRH_RX);
1832 if (pl011_split_lcrh(uap))
1833 pl011_shutdown_channel(uap, REG_LCRH_TX);
1834}
1835
1836static void pl011_disable_interrupts(struct uart_amba_port *uap)
1837{
1838 spin_lock_irq(&uap->port.lock);
1839
1840 /* mask all interrupts and clear all pending ones */
1841 uap->im = 0;
1842 pl011_write(uap->im, uap, REG_IMSC);
1843 pl011_write(0xffff, uap, REG_ICR);
1844
1845 spin_unlock_irq(&uap->port.lock);
1846}
1847
1848static void pl011_shutdown(struct uart_port *port)
1849{
1850 struct uart_amba_port *uap =
1851 container_of(port, struct uart_amba_port, port);
1852
1853 pl011_disable_interrupts(uap);
1854
1855 pl011_dma_shutdown(uap);
1856
1857 free_irq(uap->port.irq, uap);
1858
1859 pl011_disable_uart(uap);
1860
1861 /*
1862 * Shut down the clock producer
1863 */
1864 clk_disable_unprepare(uap->clk);
1865 /* Optionally let pins go into sleep states */
1866 pinctrl_pm_select_sleep_state(port->dev);
1867
1868 if (dev_get_platdata(uap->port.dev)) {
1869 struct amba_pl011_data *plat;
1870
1871 plat = dev_get_platdata(uap->port.dev);
1872 if (plat->exit)
1873 plat->exit();
1874 }
1875
1876 if (uap->port.ops->flush_buffer)
1877 uap->port.ops->flush_buffer(port);
1878}
1879
1880static void sbsa_uart_shutdown(struct uart_port *port)
1881{
1882 struct uart_amba_port *uap =
1883 container_of(port, struct uart_amba_port, port);
1884
1885 pl011_disable_interrupts(uap);
1886
1887 free_irq(uap->port.irq, uap);
1888
1889 if (uap->port.ops->flush_buffer)
1890 uap->port.ops->flush_buffer(port);
1891}
1892
1893static void
1894pl011_setup_status_masks(struct uart_port *port, struct ktermios *termios)
1895{
1896 port->read_status_mask = UART011_DR_OE | 255;
1897 if (termios->c_iflag & INPCK)
1898 port->read_status_mask |= UART011_DR_FE | UART011_DR_PE;
1899 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
1900 port->read_status_mask |= UART011_DR_BE;
1901
1902 /*
1903 * Characters to ignore
1904 */
1905 port->ignore_status_mask = 0;
1906 if (termios->c_iflag & IGNPAR)
1907 port->ignore_status_mask |= UART011_DR_FE | UART011_DR_PE;
1908 if (termios->c_iflag & IGNBRK) {
1909 port->ignore_status_mask |= UART011_DR_BE;
1910 /*
1911 * If we're ignoring parity and break indicators,
1912 * ignore overruns too (for real raw support).
1913 */
1914 if (termios->c_iflag & IGNPAR)
1915 port->ignore_status_mask |= UART011_DR_OE;
1916 }
1917
1918 /*
1919 * Ignore all characters if CREAD is not set.
1920 */
1921 if ((termios->c_cflag & CREAD) == 0)
1922 port->ignore_status_mask |= UART_DUMMY_DR_RX;
1923}
1924
1925static void
1926pl011_set_termios(struct uart_port *port, struct ktermios *termios,
1927 struct ktermios *old)
1928{
1929 struct uart_amba_port *uap =
1930 container_of(port, struct uart_amba_port, port);
1931 unsigned int lcr_h, old_cr;
1932 unsigned long flags;
1933 unsigned int baud, quot, clkdiv;
1934
1935 if (uap->vendor->oversampling)
1936 clkdiv = 8;
1937 else
1938 clkdiv = 16;
1939
1940 /*
1941 * Ask the core to calculate the divisor for us.
1942 */
1943 baud = uart_get_baud_rate(port, termios, old, 0,
1944 port->uartclk / clkdiv);
1945#ifdef CONFIG_DMA_ENGINE
1946 /*
1947 * Adjust RX DMA polling rate with baud rate if not specified.
1948 */
1949 if (uap->dmarx.auto_poll_rate)
1950 uap->dmarx.poll_rate = DIV_ROUND_UP(10000000, baud);
1951#endif
1952
1953 if (baud > port->uartclk/16)
1954 quot = DIV_ROUND_CLOSEST(port->uartclk * 8, baud);
1955 else
1956 quot = DIV_ROUND_CLOSEST(port->uartclk * 4, baud);
1957
1958 switch (termios->c_cflag & CSIZE) {
1959 case CS5:
1960 lcr_h = UART01x_LCRH_WLEN_5;
1961 break;
1962 case CS6:
1963 lcr_h = UART01x_LCRH_WLEN_6;
1964 break;
1965 case CS7:
1966 lcr_h = UART01x_LCRH_WLEN_7;
1967 break;
1968 default: // CS8
1969 lcr_h = UART01x_LCRH_WLEN_8;
1970 break;
1971 }
1972 if (termios->c_cflag & CSTOPB)
1973 lcr_h |= UART01x_LCRH_STP2;
1974 if (termios->c_cflag & PARENB) {
1975 lcr_h |= UART01x_LCRH_PEN;
1976 if (!(termios->c_cflag & PARODD))
1977 lcr_h |= UART01x_LCRH_EPS;
1978 if (termios->c_cflag & CMSPAR)
1979 lcr_h |= UART011_LCRH_SPS;
1980 }
1981 if (uap->fifosize > 1)
1982 lcr_h |= UART01x_LCRH_FEN;
1983
1984 spin_lock_irqsave(&port->lock, flags);
1985
1986 /*
1987 * Update the per-port timeout.
1988 */
1989 uart_update_timeout(port, termios->c_cflag, baud);
1990
1991 pl011_setup_status_masks(port, termios);
1992
1993 if (UART_ENABLE_MS(port, termios->c_cflag))
1994 pl011_enable_ms(port);
1995
1996 /* first, disable everything */
1997 old_cr = pl011_read(uap, REG_CR);
1998 pl011_write(0, uap, REG_CR);
1999
2000 if (termios->c_cflag & CRTSCTS) {
2001 if (old_cr & UART011_CR_RTS)
2002 old_cr |= UART011_CR_RTSEN;
2003
2004 old_cr |= UART011_CR_CTSEN;
2005 uap->autorts = true;
2006 } else {
2007 old_cr &= ~(UART011_CR_CTSEN | UART011_CR_RTSEN);
2008 uap->autorts = false;
2009 }
2010
2011 if (uap->vendor->oversampling) {
2012 if (baud > port->uartclk / 16)
2013 old_cr |= ST_UART011_CR_OVSFACT;
2014 else
2015 old_cr &= ~ST_UART011_CR_OVSFACT;
2016 }
2017
2018 /*
2019 * Workaround for the ST Micro oversampling variants to
2020 * increase the bitrate slightly, by lowering the divisor,
2021 * to avoid delayed sampling of start bit at high speeds,
2022 * else we see data corruption.
2023 */
2024 if (uap->vendor->oversampling) {
2025 if ((baud >= 3000000) && (baud < 3250000) && (quot > 1))
2026 quot -= 1;
2027 else if ((baud > 3250000) && (quot > 2))
2028 quot -= 2;
2029 }
2030 /* Set baud rate */
2031 pl011_write(quot & 0x3f, uap, REG_FBRD);
2032 pl011_write(quot >> 6, uap, REG_IBRD);
2033
2034 /*
2035 * ----------v----------v----------v----------v-----
2036 * NOTE: REG_LCRH_TX and REG_LCRH_RX MUST BE WRITTEN AFTER
2037 * REG_FBRD & REG_IBRD.
2038 * ----------^----------^----------^----------^-----
2039 */
2040 pl011_write_lcr_h(uap, lcr_h);
2041 pl011_write(old_cr, uap, REG_CR);
2042
2043 spin_unlock_irqrestore(&port->lock, flags);
2044}
2045
2046static void
2047sbsa_uart_set_termios(struct uart_port *port, struct ktermios *termios,
2048 struct ktermios *old)
2049{
2050 struct uart_amba_port *uap =
2051 container_of(port, struct uart_amba_port, port);
2052 unsigned long flags;
2053
2054 tty_termios_encode_baud_rate(termios, uap->fixed_baud, uap->fixed_baud);
2055
2056 /* The SBSA UART only supports 8n1 without hardware flow control. */
2057 termios->c_cflag &= ~(CSIZE | CSTOPB | PARENB | PARODD);
2058 termios->c_cflag &= ~(CMSPAR | CRTSCTS);
2059 termios->c_cflag |= CS8 | CLOCAL;
2060
2061 spin_lock_irqsave(&port->lock, flags);
2062 uart_update_timeout(port, CS8, uap->fixed_baud);
2063 pl011_setup_status_masks(port, termios);
2064 spin_unlock_irqrestore(&port->lock, flags);
2065}
2066
2067static const char *pl011_type(struct uart_port *port)
2068{
2069 struct uart_amba_port *uap =
2070 container_of(port, struct uart_amba_port, port);
2071 return uap->port.type == PORT_AMBA ? uap->type : NULL;
2072}
2073
2074/*
2075 * Release the memory region(s) being used by 'port'
2076 */
2077static void pl011_release_port(struct uart_port *port)
2078{
2079 release_mem_region(port->mapbase, SZ_4K);
2080}
2081
2082/*
2083 * Request the memory region(s) being used by 'port'
2084 */
2085static int pl011_request_port(struct uart_port *port)
2086{
2087 return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
2088 != NULL ? 0 : -EBUSY;
2089}
2090
2091/*
2092 * Configure/autoconfigure the port.
2093 */
2094static void pl011_config_port(struct uart_port *port, int flags)
2095{
2096 if (flags & UART_CONFIG_TYPE) {
2097 port->type = PORT_AMBA;
2098 pl011_request_port(port);
2099 }
2100}
2101
2102/*
2103 * verify the new serial_struct (for TIOCSSERIAL).
2104 */
2105static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser)
2106{
2107 int ret = 0;
2108 if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
2109 ret = -EINVAL;
2110 if (ser->irq < 0 || ser->irq >= nr_irqs)
2111 ret = -EINVAL;
2112 if (ser->baud_base < 9600)
2113 ret = -EINVAL;
2114 return ret;
2115}
2116
2117static struct uart_ops amba_pl011_pops = {
2118 .tx_empty = pl011_tx_empty,
2119 .set_mctrl = pl011_set_mctrl,
2120 .get_mctrl = pl011_get_mctrl,
2121 .stop_tx = pl011_stop_tx,
2122 .start_tx = pl011_start_tx,
2123 .stop_rx = pl011_stop_rx,
2124 .enable_ms = pl011_enable_ms,
2125 .break_ctl = pl011_break_ctl,
2126 .startup = pl011_startup,
2127 .shutdown = pl011_shutdown,
2128 .flush_buffer = pl011_dma_flush_buffer,
2129 .set_termios = pl011_set_termios,
2130 .type = pl011_type,
2131 .release_port = pl011_release_port,
2132 .request_port = pl011_request_port,
2133 .config_port = pl011_config_port,
2134 .verify_port = pl011_verify_port,
2135#ifdef CONFIG_CONSOLE_POLL
2136 .poll_init = pl011_hwinit,
2137 .poll_get_char = pl011_get_poll_char,
2138 .poll_put_char = pl011_put_poll_char,
2139#endif
2140};
2141
2142static void sbsa_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
2143{
2144}
2145
2146static unsigned int sbsa_uart_get_mctrl(struct uart_port *port)
2147{
2148 return 0;
2149}
2150
2151static const struct uart_ops sbsa_uart_pops = {
2152 .tx_empty = pl011_tx_empty,
2153 .set_mctrl = sbsa_uart_set_mctrl,
2154 .get_mctrl = sbsa_uart_get_mctrl,
2155 .stop_tx = pl011_stop_tx,
2156 .start_tx = pl011_start_tx,
2157 .stop_rx = pl011_stop_rx,
2158 .startup = sbsa_uart_startup,
2159 .shutdown = sbsa_uart_shutdown,
2160 .set_termios = sbsa_uart_set_termios,
2161 .type = pl011_type,
2162 .release_port = pl011_release_port,
2163 .request_port = pl011_request_port,
2164 .config_port = pl011_config_port,
2165 .verify_port = pl011_verify_port,
2166#ifdef CONFIG_CONSOLE_POLL
2167 .poll_init = pl011_hwinit,
2168 .poll_get_char = pl011_get_poll_char,
2169 .poll_put_char = pl011_put_poll_char,
2170#endif
2171};
2172
2173static struct uart_amba_port *amba_ports[UART_NR];
2174
2175#ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE
2176
2177static void pl011_console_putchar(struct uart_port *port, int ch)
2178{
2179 struct uart_amba_port *uap =
2180 container_of(port, struct uart_amba_port, port);
2181
2182 while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF)
2183 cpu_relax();
2184 pl011_write(ch, uap, REG_DR);
2185}
2186
2187static void
2188pl011_console_write(struct console *co, const char *s, unsigned int count)
2189{
2190 struct uart_amba_port *uap = amba_ports[co->index];
2191 unsigned int old_cr = 0, new_cr;
2192 unsigned long flags;
2193 int locked = 1;
2194
2195 clk_enable(uap->clk);
2196
2197 local_irq_save(flags);
2198 if (uap->port.sysrq)
2199 locked = 0;
2200 else if (oops_in_progress)
2201 locked = spin_trylock(&uap->port.lock);
2202 else
2203 spin_lock(&uap->port.lock);
2204
2205 /*
2206 * First save the CR then disable the interrupts
2207 */
2208 if (!uap->vendor->always_enabled) {
2209 old_cr = pl011_read(uap, REG_CR);
2210 new_cr = old_cr & ~UART011_CR_CTSEN;
2211 new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
2212 pl011_write(new_cr, uap, REG_CR);
2213 }
2214
2215 uart_console_write(&uap->port, s, count, pl011_console_putchar);
2216
2217 /*
2218 * Finally, wait for transmitter to become empty
2219 * and restore the TCR
2220 */
2221 while (pl011_read(uap, REG_FR) & uap->vendor->fr_busy)
2222 cpu_relax();
2223 if (!uap->vendor->always_enabled)
2224 pl011_write(old_cr, uap, REG_CR);
2225
2226 if (locked)
2227 spin_unlock(&uap->port.lock);
2228 local_irq_restore(flags);
2229
2230 clk_disable(uap->clk);
2231}
2232
2233static void __init
2234pl011_console_get_options(struct uart_amba_port *uap, int *baud,
2235 int *parity, int *bits)
2236{
2237 if (pl011_read(uap, REG_CR) & UART01x_CR_UARTEN) {
2238 unsigned int lcr_h, ibrd, fbrd;
2239
2240 lcr_h = pl011_read(uap, REG_LCRH_TX);
2241
2242 *parity = 'n';
2243 if (lcr_h & UART01x_LCRH_PEN) {
2244 if (lcr_h & UART01x_LCRH_EPS)
2245 *parity = 'e';
2246 else
2247 *parity = 'o';
2248 }
2249
2250 if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
2251 *bits = 7;
2252 else
2253 *bits = 8;
2254
2255 ibrd = pl011_read(uap, REG_IBRD);
2256 fbrd = pl011_read(uap, REG_FBRD);
2257
2258 *baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd);
2259
2260 if (uap->vendor->oversampling) {
2261 if (pl011_read(uap, REG_CR)
2262 & ST_UART011_CR_OVSFACT)
2263 *baud *= 2;
2264 }
2265 }
2266}
2267
2268static int __init pl011_console_setup(struct console *co, char *options)
2269{
2270 struct uart_amba_port *uap;
2271 int baud = 38400;
2272 int bits = 8;
2273 int parity = 'n';
2274 int flow = 'n';
2275 int ret;
2276
2277 /*
2278 * Check whether an invalid uart number has been specified, and
2279 * if so, search for the first available port that does have
2280 * console support.
2281 */
2282 if (co->index >= UART_NR)
2283 co->index = 0;
2284 uap = amba_ports[co->index];
2285 if (!uap)
2286 return -ENODEV;
2287
2288 /* Allow pins to be muxed in and configured */
2289 pinctrl_pm_select_default_state(uap->port.dev);
2290
2291 ret = clk_prepare(uap->clk);
2292 if (ret)
2293 return ret;
2294
2295 if (dev_get_platdata(uap->port.dev)) {
2296 struct amba_pl011_data *plat;
2297
2298 plat = dev_get_platdata(uap->port.dev);
2299 if (plat->init)
2300 plat->init();
2301 }
2302
2303 uap->port.uartclk = clk_get_rate(uap->clk);
2304
2305 if (uap->vendor->fixed_options) {
2306 baud = uap->fixed_baud;
2307 } else {
2308 if (options)
2309 uart_parse_options(options,
2310 &baud, &parity, &bits, &flow);
2311 else
2312 pl011_console_get_options(uap, &baud, &parity, &bits);
2313 }
2314
2315 return uart_set_options(&uap->port, co, baud, parity, bits, flow);
2316}
2317
2318/**
2319 * pl011_console_match - non-standard console matching
2320 * @co: registering console
2321 * @name: name from console command line
2322 * @idx: index from console command line
2323 * @options: ptr to option string from console command line
2324 *
2325 * Only attempts to match console command lines of the form:
2326 * console=pl011,mmio|mmio32,<addr>[,<options>]
2327 * console=pl011,0x<addr>[,<options>]
2328 * This form is used to register an initial earlycon boot console and
2329 * replace it with the amba_console at pl011 driver init.
2330 *
2331 * Performs console setup for a match (as required by interface)
2332 * If no <options> are specified, then assume the h/w is already setup.
2333 *
2334 * Returns 0 if console matches; otherwise non-zero to use default matching
2335 */
2336static int __init pl011_console_match(struct console *co, char *name, int idx,
2337 char *options)
2338{
2339 unsigned char iotype;
2340 resource_size_t addr;
2341 int i;
2342
2343 if (strcmp(name, "pl011") != 0)
2344 return -ENODEV;
2345
2346 if (uart_parse_earlycon(options, &iotype, &addr, &options))
2347 return -ENODEV;
2348
2349 if (iotype != UPIO_MEM && iotype != UPIO_MEM32)
2350 return -ENODEV;
2351
2352 /* try to match the port specified on the command line */
2353 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) {
2354 struct uart_port *port;
2355
2356 if (!amba_ports[i])
2357 continue;
2358
2359 port = &amba_ports[i]->port;
2360
2361 if (port->mapbase != addr)
2362 continue;
2363
2364 co->index = i;
2365 port->cons = co;
2366 return pl011_console_setup(co, options);
2367 }
2368
2369 return -ENODEV;
2370}
2371
2372static struct uart_driver amba_reg;
2373static struct console amba_console = {
2374 .name = "ttyAMA",
2375 .write = pl011_console_write,
2376 .device = uart_console_device,
2377 .setup = pl011_console_setup,
2378 .match = pl011_console_match,
2379 .flags = CON_PRINTBUFFER,
2380 .index = -1,
2381 .data = &amba_reg,
2382};
2383
2384#define AMBA_CONSOLE (&amba_console)
2385
2386static void pl011_putc(struct uart_port *port, int c)
2387{
2388 while (readl(port->membase + UART01x_FR) & UART01x_FR_TXFF)
2389 cpu_relax();
2390 if (port->iotype == UPIO_MEM32)
2391 writel(c, port->membase + UART01x_DR);
2392 else
2393 writeb(c, port->membase + UART01x_DR);
2394 while (readl(port->membase + UART01x_FR) & UART01x_FR_BUSY)
2395 cpu_relax();
2396}
2397
2398static void pl011_early_write(struct console *con, const char *s, unsigned n)
2399{
2400 struct earlycon_device *dev = con->data;
2401
2402 uart_console_write(&dev->port, s, n, pl011_putc);
2403}
2404
2405static int __init pl011_early_console_setup(struct earlycon_device *device,
2406 const char *opt)
2407{
2408 if (!device->port.membase)
2409 return -ENODEV;
2410
2411 device->con->write = pl011_early_write;
2412 return 0;
2413}
2414OF_EARLYCON_DECLARE(pl011, "arm,pl011", pl011_early_console_setup);
2415OF_EARLYCON_DECLARE(pl011, "arm,sbsa-uart", pl011_early_console_setup);
2416
2417#else
2418#define AMBA_CONSOLE NULL
2419#endif
2420
2421static struct uart_driver amba_reg = {
2422 .owner = THIS_MODULE,
2423 .driver_name = "ttyAMA",
2424 .dev_name = "ttyAMA",
2425 .major = SERIAL_AMBA_MAJOR,
2426 .minor = SERIAL_AMBA_MINOR,
2427 .nr = UART_NR,
2428 .cons = AMBA_CONSOLE,
2429};
2430
2431static int pl011_probe_dt_alias(int index, struct device *dev)
2432{
2433 struct device_node *np;
2434 static bool seen_dev_with_alias = false;
2435 static bool seen_dev_without_alias = false;
2436 int ret = index;
2437
2438 if (!IS_ENABLED(CONFIG_OF))
2439 return ret;
2440
2441 np = dev->of_node;
2442 if (!np)
2443 return ret;
2444
2445 ret = of_alias_get_id(np, "serial");
2446 if (ret < 0) {
2447 seen_dev_without_alias = true;
2448 ret = index;
2449 } else {
2450 seen_dev_with_alias = true;
2451 if (ret >= ARRAY_SIZE(amba_ports) || amba_ports[ret] != NULL) {
2452 dev_warn(dev, "requested serial port %d not available.\n", ret);
2453 ret = index;
2454 }
2455 }
2456
2457 if (seen_dev_with_alias && seen_dev_without_alias)
2458 dev_warn(dev, "aliased and non-aliased serial devices found in device tree. Serial port enumeration may be unpredictable.\n");
2459
2460 return ret;
2461}
2462
2463/* unregisters the driver also if no more ports are left */
2464static void pl011_unregister_port(struct uart_amba_port *uap)
2465{
2466 int i;
2467 bool busy = false;
2468
2469 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) {
2470 if (amba_ports[i] == uap)
2471 amba_ports[i] = NULL;
2472 else if (amba_ports[i])
2473 busy = true;
2474 }
2475 pl011_dma_remove(uap);
2476 if (!busy)
2477 uart_unregister_driver(&amba_reg);
2478}
2479
2480static int pl011_find_free_port(void)
2481{
2482 int i;
2483
2484 for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
2485 if (amba_ports[i] == NULL)
2486 return i;
2487
2488 return -EBUSY;
2489}
2490
2491static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap,
2492 struct resource *mmiobase, int index)
2493{
2494 void __iomem *base;
2495
2496 base = devm_ioremap_resource(dev, mmiobase);
2497 if (IS_ERR(base))
2498 return PTR_ERR(base);
2499
2500 index = pl011_probe_dt_alias(index, dev);
2501
2502 uap->old_cr = 0;
2503 uap->port.dev = dev;
2504 uap->port.mapbase = mmiobase->start;
2505 uap->port.membase = base;
2506 uap->port.fifosize = uap->fifosize;
2507 uap->port.flags = UPF_BOOT_AUTOCONF;
2508 uap->port.line = index;
2509
2510 amba_ports[index] = uap;
2511
2512 return 0;
2513}
2514
2515static int pl011_register_port(struct uart_amba_port *uap)
2516{
2517 int ret;
2518
2519 /* Ensure interrupts from this UART are masked and cleared */
2520 pl011_write(0, uap, REG_IMSC);
2521 pl011_write(0xffff, uap, REG_ICR);
2522
2523 if (!amba_reg.state) {
2524 ret = uart_register_driver(&amba_reg);
2525 if (ret < 0) {
2526 dev_err(uap->port.dev,
2527 "Failed to register AMBA-PL011 driver\n");
2528 return ret;
2529 }
2530 }
2531
2532 ret = uart_add_one_port(&amba_reg, &uap->port);
2533 if (ret)
2534 pl011_unregister_port(uap);
2535
2536 return ret;
2537}
2538
2539static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
2540{
2541 struct uart_amba_port *uap;
2542 struct vendor_data *vendor = id->data;
2543 int portnr, ret;
2544
2545 portnr = pl011_find_free_port();
2546 if (portnr < 0)
2547 return portnr;
2548
2549 uap = devm_kzalloc(&dev->dev, sizeof(struct uart_amba_port),
2550 GFP_KERNEL);
2551 if (!uap)
2552 return -ENOMEM;
2553
2554 uap->clk = devm_clk_get(&dev->dev, NULL);
2555 if (IS_ERR(uap->clk))
2556 return PTR_ERR(uap->clk);
2557
2558 uap->reg_offset = vendor->reg_offset;
2559 uap->vendor = vendor;
2560 uap->fifosize = vendor->get_fifosize(dev);
2561 uap->port.iotype = vendor->access_32b ? UPIO_MEM32 : UPIO_MEM;
2562 uap->port.irq = dev->irq[0];
2563 uap->port.ops = &amba_pl011_pops;
2564
2565 snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev));
2566
2567 ret = pl011_setup_port(&dev->dev, uap, &dev->res, portnr);
2568 if (ret)
2569 return ret;
2570
2571 amba_set_drvdata(dev, uap);
2572
2573 return pl011_register_port(uap);
2574}
2575
2576static int pl011_remove(struct amba_device *dev)
2577{
2578 struct uart_amba_port *uap = amba_get_drvdata(dev);
2579
2580 uart_remove_one_port(&amba_reg, &uap->port);
2581 pl011_unregister_port(uap);
2582 return 0;
2583}
2584
2585#ifdef CONFIG_PM_SLEEP
2586static int pl011_suspend(struct device *dev)
2587{
2588 struct uart_amba_port *uap = dev_get_drvdata(dev);
2589
2590 if (!uap)
2591 return -EINVAL;
2592
2593 return uart_suspend_port(&amba_reg, &uap->port);
2594}
2595
2596static int pl011_resume(struct device *dev)
2597{
2598 struct uart_amba_port *uap = dev_get_drvdata(dev);
2599
2600 if (!uap)
2601 return -EINVAL;
2602
2603 return uart_resume_port(&amba_reg, &uap->port);
2604}
2605#endif
2606
2607static SIMPLE_DEV_PM_OPS(pl011_dev_pm_ops, pl011_suspend, pl011_resume);
2608
2609static int sbsa_uart_probe(struct platform_device *pdev)
2610{
2611 struct uart_amba_port *uap;
2612 struct resource *r;
2613 int portnr, ret;
2614 int baudrate;
2615
2616 /*
2617 * Check the mandatory baud rate parameter in the DT node early
2618 * so that we can easily exit with the error.
2619 */
2620 if (pdev->dev.of_node) {
2621 struct device_node *np = pdev->dev.of_node;
2622
2623 ret = of_property_read_u32(np, "current-speed", &baudrate);
2624 if (ret)
2625 return ret;
2626 } else {
2627 baudrate = 115200;
2628 }
2629
2630 portnr = pl011_find_free_port();
2631 if (portnr < 0)
2632 return portnr;
2633
2634 uap = devm_kzalloc(&pdev->dev, sizeof(struct uart_amba_port),
2635 GFP_KERNEL);
2636 if (!uap)
2637 return -ENOMEM;
2638
2639 ret = platform_get_irq(pdev, 0);
2640 if (ret < 0) {
2641 if (ret != -EPROBE_DEFER)
2642 dev_err(&pdev->dev, "cannot obtain irq\n");
2643 return ret;
2644 }
2645 uap->port.irq = ret;
2646
2647 uap->reg_offset = vendor_sbsa.reg_offset;
2648 uap->vendor = &vendor_sbsa;
2649 uap->fifosize = 32;
2650 uap->port.iotype = vendor_sbsa.access_32b ? UPIO_MEM32 : UPIO_MEM;
2651 uap->port.ops = &sbsa_uart_pops;
2652 uap->fixed_baud = baudrate;
2653
2654 snprintf(uap->type, sizeof(uap->type), "SBSA");
2655
2656 r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2657
2658 ret = pl011_setup_port(&pdev->dev, uap, r, portnr);
2659 if (ret)
2660 return ret;
2661
2662 platform_set_drvdata(pdev, uap);
2663
2664 return pl011_register_port(uap);
2665}
2666
2667static int sbsa_uart_remove(struct platform_device *pdev)
2668{
2669 struct uart_amba_port *uap = platform_get_drvdata(pdev);
2670
2671 uart_remove_one_port(&amba_reg, &uap->port);
2672 pl011_unregister_port(uap);
2673 return 0;
2674}
2675
2676static const struct of_device_id sbsa_uart_of_match[] = {
2677 { .compatible = "arm,sbsa-uart", },
2678 {},
2679};
2680MODULE_DEVICE_TABLE(of, sbsa_uart_of_match);
2681
2682static const struct acpi_device_id sbsa_uart_acpi_match[] = {
2683 { "ARMH0011", 0 },
2684 {},
2685};
2686MODULE_DEVICE_TABLE(acpi, sbsa_uart_acpi_match);
2687
2688static struct platform_driver arm_sbsa_uart_platform_driver = {
2689 .probe = sbsa_uart_probe,
2690 .remove = sbsa_uart_remove,
2691 .driver = {
2692 .name = "sbsa-uart",
2693 .of_match_table = of_match_ptr(sbsa_uart_of_match),
2694 .acpi_match_table = ACPI_PTR(sbsa_uart_acpi_match),
2695 },
2696};
2697
2698static struct amba_id pl011_ids[] = {
2699 {
2700 .id = 0x00041011,
2701 .mask = 0x000fffff,
2702 .data = &vendor_arm,
2703 },
2704 {
2705 .id = 0x00380802,
2706 .mask = 0x00ffffff,
2707 .data = &vendor_st,
2708 },
2709 {
2710 .id = AMBA_LINUX_ID(0x00, 0x1, 0xffe),
2711 .mask = 0x00ffffff,
2712 .data = &vendor_zte,
2713 },
2714 { 0, 0 },
2715};
2716
2717MODULE_DEVICE_TABLE(amba, pl011_ids);
2718
2719static struct amba_driver pl011_driver = {
2720 .drv = {
2721 .name = "uart-pl011",
2722 .pm = &pl011_dev_pm_ops,
2723 },
2724 .id_table = pl011_ids,
2725 .probe = pl011_probe,
2726 .remove = pl011_remove,
2727};
2728
2729static int __init pl011_init(void)
2730{
2731 printk(KERN_INFO "Serial: AMBA PL011 UART driver\n");
2732
2733 if (platform_driver_register(&arm_sbsa_uart_platform_driver))
2734 pr_warn("could not register SBSA UART platform driver\n");
2735 return amba_driver_register(&pl011_driver);
2736}
2737
2738static void __exit pl011_exit(void)
2739{
2740 platform_driver_unregister(&arm_sbsa_uart_platform_driver);
2741 amba_driver_unregister(&pl011_driver);
2742}
2743
2744/*
2745 * While this can be a module, if builtin it's most likely the console
2746 * So let's leave module_exit but move module_init to an earlier place
2747 */
2748arch_initcall(pl011_init);
2749module_exit(pl011_exit);
2750
2751MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
2752MODULE_DESCRIPTION("ARM AMBA serial port driver");
2753MODULE_LICENSE("GPL");