1// SPDX-License-Identifier: GPL-2.0
   2/*
   3 *Copyright (C) 2011 LAPIS Semiconductor Co., Ltd.
   4 */
   5#include <linux/kernel.h>
   6#include <linux/serial.h>
   7#include <linux/serial_reg.h>
   8#include <linux/slab.h>
   9#include <linux/module.h>
  10#include <linux/pci.h>
  11#include <linux/console.h>
  12#include <linux/serial_core.h>
  13#include <linux/tty.h>
  14#include <linux/tty_flip.h>
  15#include <linux/interrupt.h>
  16#include <linux/io.h>
  17#include <linux/dmi.h>
  18#include <linux/nmi.h>
  19#include <linux/delay.h>
  20#include <linux/of.h>
  21
  22#include <linux/debugfs.h>
  23#include <linux/dmaengine.h>
  24#include <linux/pch_dma.h>
  25
  26enum {
  27	PCH_UART_HANDLED_RX_INT_SHIFT,
  28	PCH_UART_HANDLED_TX_INT_SHIFT,
  29	PCH_UART_HANDLED_RX_ERR_INT_SHIFT,
  30	PCH_UART_HANDLED_RX_TRG_INT_SHIFT,
  31	PCH_UART_HANDLED_MS_INT_SHIFT,
  32	PCH_UART_HANDLED_LS_INT_SHIFT,
  33};
  34
  35#define PCH_UART_DRIVER_DEVICE "ttyPCH"
  36
  37/* Set the max number of UART port
  38 * Intel EG20T PCH: 4 port
  39 * LAPIS Semiconductor ML7213 IOH: 3 port
  40 * LAPIS Semiconductor ML7223 IOH: 2 port
  41*/
  42#define PCH_UART_NR	4
  43
  44#define PCH_UART_HANDLED_RX_INT	(1<<((PCH_UART_HANDLED_RX_INT_SHIFT)<<1))
  45#define PCH_UART_HANDLED_TX_INT	(1<<((PCH_UART_HANDLED_TX_INT_SHIFT)<<1))
  46#define PCH_UART_HANDLED_RX_ERR_INT	(1<<((\
  47					PCH_UART_HANDLED_RX_ERR_INT_SHIFT)<<1))
  48#define PCH_UART_HANDLED_RX_TRG_INT	(1<<((\
  49					PCH_UART_HANDLED_RX_TRG_INT_SHIFT)<<1))
  50#define PCH_UART_HANDLED_MS_INT	(1<<((PCH_UART_HANDLED_MS_INT_SHIFT)<<1))
  51
  52#define PCH_UART_HANDLED_LS_INT	(1<<((PCH_UART_HANDLED_LS_INT_SHIFT)<<1))
  53
  54#define PCH_UART_RBR		0x00
  55#define PCH_UART_THR		0x00
  56
  57#define PCH_UART_IER_MASK	(PCH_UART_IER_ERBFI|PCH_UART_IER_ETBEI|\
  58				PCH_UART_IER_ELSI|PCH_UART_IER_EDSSI)
  59#define PCH_UART_IER_ERBFI	0x00000001
  60#define PCH_UART_IER_ETBEI	0x00000002
  61#define PCH_UART_IER_ELSI	0x00000004
  62#define PCH_UART_IER_EDSSI	0x00000008
  63
  64#define PCH_UART_IIR_IP			0x00000001
  65#define PCH_UART_IIR_IID		0x00000006
  66#define PCH_UART_IIR_MSI		0x00000000
  67#define PCH_UART_IIR_TRI		0x00000002
  68#define PCH_UART_IIR_RRI		0x00000004
  69#define PCH_UART_IIR_REI		0x00000006
  70#define PCH_UART_IIR_TOI		0x00000008
  71#define PCH_UART_IIR_FIFO256		0x00000020
  72#define PCH_UART_IIR_FIFO64		PCH_UART_IIR_FIFO256
  73#define PCH_UART_IIR_FE			0x000000C0
  74
  75#define PCH_UART_FCR_FIFOE		0x00000001
  76#define PCH_UART_FCR_RFR		0x00000002
  77#define PCH_UART_FCR_TFR		0x00000004
  78#define PCH_UART_FCR_DMS		0x00000008
  79#define PCH_UART_FCR_FIFO256		0x00000020
  80#define PCH_UART_FCR_RFTL		0x000000C0
  81
  82#define PCH_UART_FCR_RFTL1		0x00000000
  83#define PCH_UART_FCR_RFTL64		0x00000040
  84#define PCH_UART_FCR_RFTL128		0x00000080
  85#define PCH_UART_FCR_RFTL224		0x000000C0
  86#define PCH_UART_FCR_RFTL16		PCH_UART_FCR_RFTL64
  87#define PCH_UART_FCR_RFTL32		PCH_UART_FCR_RFTL128
  88#define PCH_UART_FCR_RFTL56		PCH_UART_FCR_RFTL224
  89#define PCH_UART_FCR_RFTL4		PCH_UART_FCR_RFTL64
  90#define PCH_UART_FCR_RFTL8		PCH_UART_FCR_RFTL128
  91#define PCH_UART_FCR_RFTL14		PCH_UART_FCR_RFTL224
  92#define PCH_UART_FCR_RFTL_SHIFT		6
  93
  94#define PCH_UART_LCR_WLS	0x00000003
  95#define PCH_UART_LCR_STB	0x00000004
  96#define PCH_UART_LCR_PEN	0x00000008
  97#define PCH_UART_LCR_EPS	0x00000010
  98#define PCH_UART_LCR_SP		0x00000020
  99#define PCH_UART_LCR_SB		0x00000040
 100#define PCH_UART_LCR_DLAB	0x00000080
 101#define PCH_UART_LCR_NP		0x00000000
 102#define PCH_UART_LCR_OP		PCH_UART_LCR_PEN
 103#define PCH_UART_LCR_EP		(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS)
 104#define PCH_UART_LCR_1P		(PCH_UART_LCR_PEN | PCH_UART_LCR_SP)
 105#define PCH_UART_LCR_0P		(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS |\
 106				PCH_UART_LCR_SP)
 107
 108#define PCH_UART_LCR_5BIT	0x00000000
 109#define PCH_UART_LCR_6BIT	0x00000001
 110#define PCH_UART_LCR_7BIT	0x00000002
 111#define PCH_UART_LCR_8BIT	0x00000003
 112
 113#define PCH_UART_MCR_DTR	0x00000001
 114#define PCH_UART_MCR_RTS	0x00000002
 115#define PCH_UART_MCR_OUT	0x0000000C
 116#define PCH_UART_MCR_LOOP	0x00000010
 117#define PCH_UART_MCR_AFE	0x00000020
 118
 119#define PCH_UART_LSR_DR		0x00000001
 120#define PCH_UART_LSR_ERR	(1<<7)
 121
 122#define PCH_UART_MSR_DCTS	0x00000001
 123#define PCH_UART_MSR_DDSR	0x00000002
 124#define PCH_UART_MSR_TERI	0x00000004
 125#define PCH_UART_MSR_DDCD	0x00000008
 126#define PCH_UART_MSR_CTS	0x00000010
 127#define PCH_UART_MSR_DSR	0x00000020
 128#define PCH_UART_MSR_RI		0x00000040
 129#define PCH_UART_MSR_DCD	0x00000080
 130#define PCH_UART_MSR_DELTA	(PCH_UART_MSR_DCTS | PCH_UART_MSR_DDSR |\
 131				PCH_UART_MSR_TERI | PCH_UART_MSR_DDCD)
 132
 133#define PCH_UART_DLL		0x00
 134#define PCH_UART_DLM		0x01
 135
 136#define PCH_UART_BRCSR		0x0E
 137
 138#define PCH_UART_IID_RLS	(PCH_UART_IIR_REI)
 139#define PCH_UART_IID_RDR	(PCH_UART_IIR_RRI)
 140#define PCH_UART_IID_RDR_TO	(PCH_UART_IIR_RRI | PCH_UART_IIR_TOI)
 141#define PCH_UART_IID_THRE	(PCH_UART_IIR_TRI)
 142#define PCH_UART_IID_MS		(PCH_UART_IIR_MSI)
 143
 144#define PCH_UART_HAL_PARITY_NONE	(PCH_UART_LCR_NP)
 145#define PCH_UART_HAL_PARITY_ODD		(PCH_UART_LCR_OP)
 146#define PCH_UART_HAL_PARITY_EVEN	(PCH_UART_LCR_EP)
 147#define PCH_UART_HAL_PARITY_FIX1	(PCH_UART_LCR_1P)
 148#define PCH_UART_HAL_PARITY_FIX0	(PCH_UART_LCR_0P)
 149#define PCH_UART_HAL_5BIT		(PCH_UART_LCR_5BIT)
 150#define PCH_UART_HAL_6BIT		(PCH_UART_LCR_6BIT)
 151#define PCH_UART_HAL_7BIT		(PCH_UART_LCR_7BIT)
 152#define PCH_UART_HAL_8BIT		(PCH_UART_LCR_8BIT)
 153#define PCH_UART_HAL_STB1		0
 154#define PCH_UART_HAL_STB2		(PCH_UART_LCR_STB)
 155
 156#define PCH_UART_HAL_CLR_TX_FIFO	(PCH_UART_FCR_TFR)
 157#define PCH_UART_HAL_CLR_RX_FIFO	(PCH_UART_FCR_RFR)
 158#define PCH_UART_HAL_CLR_ALL_FIFO	(PCH_UART_HAL_CLR_TX_FIFO | \
 159					PCH_UART_HAL_CLR_RX_FIFO)
 160
 161#define PCH_UART_HAL_DMA_MODE0		0
 162#define PCH_UART_HAL_FIFO_DIS		0
 163#define PCH_UART_HAL_FIFO16		(PCH_UART_FCR_FIFOE)
 164#define PCH_UART_HAL_FIFO256		(PCH_UART_FCR_FIFOE | \
 165					PCH_UART_FCR_FIFO256)
 166#define PCH_UART_HAL_FIFO64		(PCH_UART_HAL_FIFO256)
 167#define PCH_UART_HAL_TRIGGER1		(PCH_UART_FCR_RFTL1)
 168#define PCH_UART_HAL_TRIGGER64		(PCH_UART_FCR_RFTL64)
 169#define PCH_UART_HAL_TRIGGER128		(PCH_UART_FCR_RFTL128)
 170#define PCH_UART_HAL_TRIGGER224		(PCH_UART_FCR_RFTL224)
 171#define PCH_UART_HAL_TRIGGER16		(PCH_UART_FCR_RFTL16)
 172#define PCH_UART_HAL_TRIGGER32		(PCH_UART_FCR_RFTL32)
 173#define PCH_UART_HAL_TRIGGER56		(PCH_UART_FCR_RFTL56)
 174#define PCH_UART_HAL_TRIGGER4		(PCH_UART_FCR_RFTL4)
 175#define PCH_UART_HAL_TRIGGER8		(PCH_UART_FCR_RFTL8)
 176#define PCH_UART_HAL_TRIGGER14		(PCH_UART_FCR_RFTL14)
 177#define PCH_UART_HAL_TRIGGER_L		(PCH_UART_FCR_RFTL64)
 178#define PCH_UART_HAL_TRIGGER_M		(PCH_UART_FCR_RFTL128)
 179#define PCH_UART_HAL_TRIGGER_H		(PCH_UART_FCR_RFTL224)
 180
 181#define PCH_UART_HAL_RX_INT		(PCH_UART_IER_ERBFI)
 182#define PCH_UART_HAL_TX_INT		(PCH_UART_IER_ETBEI)
 183#define PCH_UART_HAL_RX_ERR_INT		(PCH_UART_IER_ELSI)
 184#define PCH_UART_HAL_MS_INT		(PCH_UART_IER_EDSSI)
 185#define PCH_UART_HAL_ALL_INT		(PCH_UART_IER_MASK)
 186
 187#define PCH_UART_HAL_DTR		(PCH_UART_MCR_DTR)
 188#define PCH_UART_HAL_RTS		(PCH_UART_MCR_RTS)
 189#define PCH_UART_HAL_OUT		(PCH_UART_MCR_OUT)
 190#define PCH_UART_HAL_LOOP		(PCH_UART_MCR_LOOP)
 191#define PCH_UART_HAL_AFE		(PCH_UART_MCR_AFE)
 192
 193#define DEFAULT_UARTCLK   1843200 /*   1.8432 MHz */
 194#define CMITC_UARTCLK   192000000 /* 192.0000 MHz */
 195#define FRI2_64_UARTCLK  64000000 /*  64.0000 MHz */
 196#define FRI2_48_UARTCLK  48000000 /*  48.0000 MHz */
 197#define NTC1_UARTCLK     64000000 /*  64.0000 MHz */
 198#define MINNOW_UARTCLK   50000000 /*  50.0000 MHz */
 199
 200struct pch_uart_buffer {
 201	unsigned char *buf;
 202	int size;
 203};
 204
 205struct eg20t_port {
 206	struct uart_port port;
 207	int port_type;
 208	void __iomem *membase;
 209	resource_size_t mapbase;
 210	unsigned int iobase;
 211	struct pci_dev *pdev;
 212	int fifo_size;
 213	unsigned int uartclk;
 214	int start_tx;
 215	int start_rx;
 216	int tx_empty;
 217	int trigger;
 218	int trigger_level;
 219	struct pch_uart_buffer rxbuf;
 220	unsigned int dmsr;
 221	unsigned int fcr;
 222	unsigned int mcr;
 223	unsigned int use_dma;
 224	struct dma_async_tx_descriptor	*desc_tx;
 225	struct dma_async_tx_descriptor	*desc_rx;
 226	struct pch_dma_slave		param_tx;
 227	struct pch_dma_slave		param_rx;
 228	struct dma_chan			*chan_tx;
 229	struct dma_chan			*chan_rx;
 230	struct scatterlist		*sg_tx_p;
 231	int				nent;
 232	int				orig_nent;
 233	struct scatterlist		sg_rx;
 234	int				tx_dma_use;
 235	void				*rx_buf_virt;
 236	dma_addr_t			rx_buf_dma;
 237
 238#define IRQ_NAME_SIZE 17
 239	char				irq_name[IRQ_NAME_SIZE];
 240
 241	/* protect the eg20t_port private structure and io access to membase */
 242	spinlock_t lock;
 243};
 244
 245/**
 246 * struct pch_uart_driver_data - private data structure for UART-DMA
 247 * @port_type:			The type of UART port
 248 * @line_no:			UART port line number (0, 1, 2...)
 249 */
 250struct pch_uart_driver_data {
 251	int port_type;
 252	int line_no;
 253};
 254
 255enum pch_uart_num_t {
 256	pch_et20t_uart0 = 0,
 257	pch_et20t_uart1,
 258	pch_et20t_uart2,
 259	pch_et20t_uart3,
 260	pch_ml7213_uart0,
 261	pch_ml7213_uart1,
 262	pch_ml7213_uart2,
 263	pch_ml7223_uart0,
 264	pch_ml7223_uart1,
 265	pch_ml7831_uart0,
 266	pch_ml7831_uart1,
 267};
 268
 269static struct pch_uart_driver_data drv_dat[] = {
 270	[pch_et20t_uart0] = {PORT_PCH_8LINE, 0},
 271	[pch_et20t_uart1] = {PORT_PCH_2LINE, 1},
 272	[pch_et20t_uart2] = {PORT_PCH_2LINE, 2},
 273	[pch_et20t_uart3] = {PORT_PCH_2LINE, 3},
 274	[pch_ml7213_uart0] = {PORT_PCH_8LINE, 0},
 275	[pch_ml7213_uart1] = {PORT_PCH_2LINE, 1},
 276	[pch_ml7213_uart2] = {PORT_PCH_2LINE, 2},
 277	[pch_ml7223_uart0] = {PORT_PCH_8LINE, 0},
 278	[pch_ml7223_uart1] = {PORT_PCH_2LINE, 1},
 279	[pch_ml7831_uart0] = {PORT_PCH_8LINE, 0},
 280	[pch_ml7831_uart1] = {PORT_PCH_2LINE, 1},
 281};
 282
 283#ifdef CONFIG_SERIAL_PCH_UART_CONSOLE
 284static struct eg20t_port *pch_uart_ports[PCH_UART_NR];
 285#endif
 286static unsigned int default_baud = 9600;
 287static unsigned int user_uartclk = 0;
 288static const int trigger_level_256[4] = { 1, 64, 128, 224 };
 289static const int trigger_level_64[4] = { 1, 16, 32, 56 };
 290static const int trigger_level_16[4] = { 1, 4, 8, 14 };
 291static const int trigger_level_1[4] = { 1, 1, 1, 1 };
 292
 293#define PCH_REGS_BUFSIZE	1024
 294
 295
 296static ssize_t port_show_regs(struct file *file, char __user *user_buf,
 297				size_t count, loff_t *ppos)
 298{
 299	struct eg20t_port *priv = file->private_data;
 300	char *buf;
 301	u32 len = 0;
 302	ssize_t ret;
 303	unsigned char lcr;
 304
 305	buf = kzalloc(PCH_REGS_BUFSIZE, GFP_KERNEL);
 306	if (!buf)
 307		return 0;
 308
 309	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 310			"PCH EG20T port[%d] regs:\n", priv->port.line);
 311
 312	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 313			"=================================\n");
 314	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 315			"IER: \t0x%02x\n", ioread8(priv->membase + UART_IER));
 316	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 317			"IIR: \t0x%02x\n", ioread8(priv->membase + UART_IIR));
 318	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 319			"LCR: \t0x%02x\n", ioread8(priv->membase + UART_LCR));
 320	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 321			"MCR: \t0x%02x\n", ioread8(priv->membase + UART_MCR));
 322	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 323			"LSR: \t0x%02x\n", ioread8(priv->membase + UART_LSR));
 324	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 325			"MSR: \t0x%02x\n", ioread8(priv->membase + UART_MSR));
 326	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 327			"BRCSR: \t0x%02x\n",
 328			ioread8(priv->membase + PCH_UART_BRCSR));
 329
 330	lcr = ioread8(priv->membase + UART_LCR);
 331	iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR);
 332	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 333			"DLL: \t0x%02x\n", ioread8(priv->membase + UART_DLL));
 334	len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len,
 335			"DLM: \t0x%02x\n", ioread8(priv->membase + UART_DLM));
 336	iowrite8(lcr, priv->membase + UART_LCR);
 337
 338	if (len > PCH_REGS_BUFSIZE)
 339		len = PCH_REGS_BUFSIZE;
 340
 341	ret =  simple_read_from_buffer(user_buf, count, ppos, buf, len);
 342	kfree(buf);
 343	return ret;
 344}
 345
 346static const struct file_operations port_regs_ops = {
 347	.owner		= THIS_MODULE,
 348	.open		= simple_open,
 349	.read		= port_show_regs,
 350	.llseek		= default_llseek,
 351};
 352
 353static const struct dmi_system_id pch_uart_dmi_table[] = {
 354	{
 355		.ident = "CM-iTC",
 356		{
 357			DMI_MATCH(DMI_BOARD_NAME, "CM-iTC"),
 358		},
 359		(void *)CMITC_UARTCLK,
 360	},
 361	{
 362		.ident = "FRI2",
 363		{
 364			DMI_MATCH(DMI_BIOS_VERSION, "FRI2"),
 365		},
 366		(void *)FRI2_64_UARTCLK,
 367	},
 368	{
 369		.ident = "Fish River Island II",
 370		{
 371			DMI_MATCH(DMI_PRODUCT_NAME, "Fish River Island II"),
 372		},
 373		(void *)FRI2_48_UARTCLK,
 374	},
 375	{
 376		.ident = "COMe-mTT",
 377		{
 378			DMI_MATCH(DMI_BOARD_NAME, "COMe-mTT"),
 379		},
 380		(void *)NTC1_UARTCLK,
 381	},
 382	{
 383		.ident = "nanoETXexpress-TT",
 384		{
 385			DMI_MATCH(DMI_BOARD_NAME, "nanoETXexpress-TT"),
 386		},
 387		(void *)NTC1_UARTCLK,
 388	},
 389	{
 390		.ident = "MinnowBoard",
 391		{
 392			DMI_MATCH(DMI_BOARD_NAME, "MinnowBoard"),
 393		},
 394		(void *)MINNOW_UARTCLK,
 395	},
 396	{ }
 397};
 398
 399/* Return UART clock, checking for board specific clocks. */
 400static unsigned int pch_uart_get_uartclk(void)
 401{
 402	const struct dmi_system_id *d;
 403
 404	if (user_uartclk)
 405		return user_uartclk;
 406
 407	d = dmi_first_match(pch_uart_dmi_table);
 408	if (d)
 409		return (unsigned long)d->driver_data;
 410
 411	return DEFAULT_UARTCLK;
 412}
 413
 414static void pch_uart_hal_enable_interrupt(struct eg20t_port *priv,
 415					  unsigned int flag)
 416{
 417	u8 ier = ioread8(priv->membase + UART_IER);
 418	ier |= flag & PCH_UART_IER_MASK;
 419	iowrite8(ier, priv->membase + UART_IER);
 420}
 421
 422static void pch_uart_hal_disable_interrupt(struct eg20t_port *priv,
 423					   unsigned int flag)
 424{
 425	u8 ier = ioread8(priv->membase + UART_IER);
 426	ier &= ~(flag & PCH_UART_IER_MASK);
 427	iowrite8(ier, priv->membase + UART_IER);
 428}
 429
 430static int pch_uart_hal_set_line(struct eg20t_port *priv, unsigned int baud,
 431				 unsigned int parity, unsigned int bits,
 432				 unsigned int stb)
 433{
 434	unsigned int dll, dlm, lcr;
 435	int div;
 436
 437	div = DIV_ROUND_CLOSEST(priv->uartclk / 16, baud);
 438	if (div < 0 || USHRT_MAX <= div) {
 439		dev_err(priv->port.dev, "Invalid Baud(div=0x%x)\n", div);
 440		return -EINVAL;
 441	}
 442
 443	dll = (unsigned int)div & 0x00FFU;
 444	dlm = ((unsigned int)div >> 8) & 0x00FFU;
 445
 446	if (parity & ~(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS | PCH_UART_LCR_SP)) {
 447		dev_err(priv->port.dev, "Invalid parity(0x%x)\n", parity);
 448		return -EINVAL;
 449	}
 450
 451	if (bits & ~PCH_UART_LCR_WLS) {
 452		dev_err(priv->port.dev, "Invalid bits(0x%x)\n", bits);
 453		return -EINVAL;
 454	}
 455
 456	if (stb & ~PCH_UART_LCR_STB) {
 457		dev_err(priv->port.dev, "Invalid STB(0x%x)\n", stb);
 458		return -EINVAL;
 459	}
 460
 461	lcr = parity;
 462	lcr |= bits;
 463	lcr |= stb;
 464
 465	dev_dbg(priv->port.dev, "%s:baud = %u, div = %04x, lcr = %02x (%lu)\n",
 466		 __func__, baud, div, lcr, jiffies);
 467	iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR);
 468	iowrite8(dll, priv->membase + PCH_UART_DLL);
 469	iowrite8(dlm, priv->membase + PCH_UART_DLM);
 470	iowrite8(lcr, priv->membase + UART_LCR);
 471
 472	return 0;
 473}
 474
 475static int pch_uart_hal_fifo_reset(struct eg20t_port *priv,
 476				    unsigned int flag)
 477{
 478	if (flag & ~(PCH_UART_FCR_TFR | PCH_UART_FCR_RFR)) {
 479		dev_err(priv->port.dev, "%s:Invalid flag(0x%x)\n",
 480			__func__, flag);
 481		return -EINVAL;
 482	}
 483
 484	iowrite8(PCH_UART_FCR_FIFOE | priv->fcr, priv->membase + UART_FCR);
 485	iowrite8(PCH_UART_FCR_FIFOE | priv->fcr | flag,
 486		 priv->membase + UART_FCR);
 487	iowrite8(priv->fcr, priv->membase + UART_FCR);
 488
 489	return 0;
 490}
 491
 492static int pch_uart_hal_set_fifo(struct eg20t_port *priv,
 493				 unsigned int dmamode,
 494				 unsigned int fifo_size, unsigned int trigger)
 495{
 496	u8 fcr;
 497
 498	if (dmamode & ~PCH_UART_FCR_DMS) {
 499		dev_err(priv->port.dev, "%s:Invalid DMA Mode(0x%x)\n",
 500			__func__, dmamode);
 501		return -EINVAL;
 502	}
 503
 504	if (fifo_size & ~(PCH_UART_FCR_FIFOE | PCH_UART_FCR_FIFO256)) {
 505		dev_err(priv->port.dev, "%s:Invalid FIFO SIZE(0x%x)\n",
 506			__func__, fifo_size);
 507		return -EINVAL;
 508	}
 509
 510	if (trigger & ~PCH_UART_FCR_RFTL) {
 511		dev_err(priv->port.dev, "%s:Invalid TRIGGER(0x%x)\n",
 512			__func__, trigger);
 513		return -EINVAL;
 514	}
 515
 516	switch (priv->fifo_size) {
 517	case 256:
 518		priv->trigger_level =
 519		    trigger_level_256[trigger >> PCH_UART_FCR_RFTL_SHIFT];
 520		break;
 521	case 64:
 522		priv->trigger_level =
 523		    trigger_level_64[trigger >> PCH_UART_FCR_RFTL_SHIFT];
 524		break;
 525	case 16:
 526		priv->trigger_level =
 527		    trigger_level_16[trigger >> PCH_UART_FCR_RFTL_SHIFT];
 528		break;
 529	default:
 530		priv->trigger_level =
 531		    trigger_level_1[trigger >> PCH_UART_FCR_RFTL_SHIFT];
 532		break;
 533	}
 534	fcr =
 535	    dmamode | fifo_size | trigger | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR;
 536	iowrite8(PCH_UART_FCR_FIFOE, priv->membase + UART_FCR);
 537	iowrite8(PCH_UART_FCR_FIFOE | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR,
 538		 priv->membase + UART_FCR);
 539	iowrite8(fcr, priv->membase + UART_FCR);
 540	priv->fcr = fcr;
 541
 542	return 0;
 543}
 544
 545static u8 pch_uart_hal_get_modem(struct eg20t_port *priv)
 546{
 547	unsigned int msr = ioread8(priv->membase + UART_MSR);
 548	priv->dmsr = msr & PCH_UART_MSR_DELTA;
 549	return (u8)msr;
 550}
 551
 552static int pch_uart_hal_read(struct eg20t_port *priv, unsigned char *buf,
 553			     int rx_size)
 554{
 555	int i;
 556	u8 rbr, lsr;
 557	struct uart_port *port = &priv->port;
 558
 559	lsr = ioread8(priv->membase + UART_LSR);
 560	for (i = 0, lsr = ioread8(priv->membase + UART_LSR);
 561	     i < rx_size && lsr & (UART_LSR_DR | UART_LSR_BI);
 562	     lsr = ioread8(priv->membase + UART_LSR)) {
 563		rbr = ioread8(priv->membase + PCH_UART_RBR);
 564
 565		if (lsr & UART_LSR_BI) {
 566			port->icount.brk++;
 567			if (uart_handle_break(port))
 568				continue;
 569		}
 570		if (uart_handle_sysrq_char(port, rbr))
 571			continue;
 572
 573		buf[i++] = rbr;
 574	}
 575	return i;
 576}
 577
 578static unsigned char pch_uart_hal_get_iid(struct eg20t_port *priv)
 579{
 580	return ioread8(priv->membase + UART_IIR) &\
 581		      (PCH_UART_IIR_IID | PCH_UART_IIR_TOI | PCH_UART_IIR_IP);
 582}
 583
 584static u8 pch_uart_hal_get_line_status(struct eg20t_port *priv)
 585{
 586	return ioread8(priv->membase + UART_LSR);
 587}
 588
 589static void pch_uart_hal_set_break(struct eg20t_port *priv, int on)
 590{
 591	unsigned int lcr;
 592
 593	lcr = ioread8(priv->membase + UART_LCR);
 594	if (on)
 595		lcr |= PCH_UART_LCR_SB;
 596	else
 597		lcr &= ~PCH_UART_LCR_SB;
 598
 599	iowrite8(lcr, priv->membase + UART_LCR);
 600}
 601
 602static int push_rx(struct eg20t_port *priv, const unsigned char *buf,
 603		   int size)
 604{
 605	struct uart_port *port = &priv->port;
 606	struct tty_port *tport = &port->state->port;
 607
 608	tty_insert_flip_string(tport, buf, size);
 609	tty_flip_buffer_push(tport);
 610
 611	return 0;
 612}
 613
 614static int dma_push_rx(struct eg20t_port *priv, int size)
 615{
 616	int room;
 617	struct uart_port *port = &priv->port;
 618	struct tty_port *tport = &port->state->port;
 619
 620	room = tty_buffer_request_room(tport, size);
 621
 622	if (room < size)
 623		dev_warn(port->dev, "Rx overrun: dropping %u bytes\n",
 624			 size - room);
 625	if (!room)
 626		return 0;
 627
 628	tty_insert_flip_string(tport, sg_virt(&priv->sg_rx), size);
 629
 630	port->icount.rx += room;
 631
 632	return room;
 633}
 634
 635static void pch_free_dma(struct uart_port *port)
 636{
 637	struct eg20t_port *priv;
 638	priv = container_of(port, struct eg20t_port, port);
 639
 640	if (priv->chan_tx) {
 641		dma_release_channel(priv->chan_tx);
 642		priv->chan_tx = NULL;
 643	}
 644	if (priv->chan_rx) {
 645		dma_release_channel(priv->chan_rx);
 646		priv->chan_rx = NULL;
 647	}
 648
 649	if (priv->rx_buf_dma) {
 650		dma_free_coherent(port->dev, port->fifosize, priv->rx_buf_virt,
 651				  priv->rx_buf_dma);
 652		priv->rx_buf_virt = NULL;
 653		priv->rx_buf_dma = 0;
 654	}
 655
 656	return;
 657}
 658
 659static bool filter(struct dma_chan *chan, void *slave)
 660{
 661	struct pch_dma_slave *param = slave;
 662
 663	if ((chan->chan_id == param->chan_id) && (param->dma_dev ==
 664						  chan->device->dev)) {
 665		chan->private = param;
 666		return true;
 667	} else {
 668		return false;
 669	}
 670}
 671
 672static void pch_request_dma(struct uart_port *port)
 673{
 674	dma_cap_mask_t mask;
 675	struct dma_chan *chan;
 676	struct pci_dev *dma_dev;
 677	struct pch_dma_slave *param;
 678	struct eg20t_port *priv =
 679				container_of(port, struct eg20t_port, port);
 680	dma_cap_zero(mask);
 681	dma_cap_set(DMA_SLAVE, mask);
 682
 683	/* Get DMA's dev information */
 684	dma_dev = pci_get_slot(priv->pdev->bus,
 685			PCI_DEVFN(PCI_SLOT(priv->pdev->devfn), 0));
 686
 687	/* Set Tx DMA */
 688	param = &priv->param_tx;
 689	param->dma_dev = &dma_dev->dev;
 690	param->chan_id = priv->port.line * 2; /* Tx = 0, 2, 4, ... */
 691
 692	param->tx_reg = port->mapbase + UART_TX;
 693	chan = dma_request_channel(mask, filter, param);
 694	if (!chan) {
 695		dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Tx)\n",
 696			__func__);
 697		pci_dev_put(dma_dev);
 698		return;
 699	}
 700	priv->chan_tx = chan;
 701
 702	/* Set Rx DMA */
 703	param = &priv->param_rx;
 704	param->dma_dev = &dma_dev->dev;
 705	param->chan_id = priv->port.line * 2 + 1; /* Rx = Tx + 1 */
 706
 707	param->rx_reg = port->mapbase + UART_RX;
 708	chan = dma_request_channel(mask, filter, param);
 709	if (!chan) {
 710		dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Rx)\n",
 711			__func__);
 712		dma_release_channel(priv->chan_tx);
 713		priv->chan_tx = NULL;
 714		pci_dev_put(dma_dev);
 715		return;
 716	}
 717
 718	/* Get Consistent memory for DMA */
 719	priv->rx_buf_virt = dma_alloc_coherent(port->dev, port->fifosize,
 720				    &priv->rx_buf_dma, GFP_KERNEL);
 721	priv->chan_rx = chan;
 722
 723	pci_dev_put(dma_dev);
 724}
 725
 726static void pch_dma_rx_complete(void *arg)
 727{
 728	struct eg20t_port *priv = arg;
 729	struct uart_port *port = &priv->port;
 730	int count;
 731
 732	dma_sync_sg_for_cpu(port->dev, &priv->sg_rx, 1, DMA_FROM_DEVICE);
 733	count = dma_push_rx(priv, priv->trigger_level);
 734	if (count)
 735		tty_flip_buffer_push(&port->state->port);
 736	async_tx_ack(priv->desc_rx);
 737	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT |
 738					    PCH_UART_HAL_RX_ERR_INT);
 739}
 740
 741static void pch_dma_tx_complete(void *arg)
 742{
 743	struct eg20t_port *priv = arg;
 744	struct uart_port *port = &priv->port;
 745	struct scatterlist *sg = priv->sg_tx_p;
 746	int i;
 747
 748	for (i = 0; i < priv->nent; i++, sg++)
 749		uart_xmit_advance(port, sg_dma_len(sg));
 750
 751	async_tx_ack(priv->desc_tx);
 752	dma_unmap_sg(port->dev, priv->sg_tx_p, priv->orig_nent, DMA_TO_DEVICE);
 753	priv->tx_dma_use = 0;
 754	priv->nent = 0;
 755	priv->orig_nent = 0;
 756	kfree(priv->sg_tx_p);
 757	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT);
 758}
 759
 760static int handle_rx_to(struct eg20t_port *priv)
 761{
 762	struct pch_uart_buffer *buf;
 763	int rx_size;
 764	int ret;
 765	if (!priv->start_rx) {
 766		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT |
 767						     PCH_UART_HAL_RX_ERR_INT);
 768		return 0;
 769	}
 770	buf = &priv->rxbuf;
 771	do {
 772		rx_size = pch_uart_hal_read(priv, buf->buf, buf->size);
 773		ret = push_rx(priv, buf->buf, rx_size);
 774		if (ret)
 775			return 0;
 776	} while (rx_size == buf->size);
 777
 778	return PCH_UART_HANDLED_RX_INT;
 779}
 780
 781static int handle_rx(struct eg20t_port *priv)
 782{
 783	return handle_rx_to(priv);
 784}
 785
 786static int dma_handle_rx(struct eg20t_port *priv)
 787{
 788	struct uart_port *port = &priv->port;
 789	struct dma_async_tx_descriptor *desc;
 790	struct scatterlist *sg;
 791
 792	priv = container_of(port, struct eg20t_port, port);
 793	sg = &priv->sg_rx;
 794
 795	sg_init_table(&priv->sg_rx, 1); /* Initialize SG table */
 796
 797	sg_dma_len(sg) = priv->trigger_level;
 798
 799	sg_set_page(&priv->sg_rx, virt_to_page(priv->rx_buf_virt),
 800		     sg_dma_len(sg), offset_in_page(priv->rx_buf_virt));
 801
 802	sg_dma_address(sg) = priv->rx_buf_dma;
 803
 804	desc = dmaengine_prep_slave_sg(priv->chan_rx,
 805			sg, 1, DMA_DEV_TO_MEM,
 806			DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 807
 808	if (!desc)
 809		return 0;
 810
 811	priv->desc_rx = desc;
 812	desc->callback = pch_dma_rx_complete;
 813	desc->callback_param = priv;
 814	desc->tx_submit(desc);
 815	dma_async_issue_pending(priv->chan_rx);
 816
 817	return PCH_UART_HANDLED_RX_INT;
 818}
 819
 820static unsigned int handle_tx(struct eg20t_port *priv)
 821{
 822	struct uart_port *port = &priv->port;
 823	struct circ_buf *xmit = &port->state->xmit;
 824	int fifo_size;
 825	int tx_empty;
 826
 827	if (!priv->start_tx) {
 828		dev_info(priv->port.dev, "%s:Tx isn't started. (%lu)\n",
 829			__func__, jiffies);
 830		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 831		priv->tx_empty = 1;
 832		return 0;
 833	}
 834
 835	fifo_size = max(priv->fifo_size, 1);
 836	tx_empty = 1;
 837	if (port->x_char) {
 838		iowrite8(port->x_char, priv->membase + PCH_UART_THR);
 839		port->icount.tx++;
 840		port->x_char = 0;
 841		tx_empty = 0;
 842		fifo_size--;
 843	}
 844
 845	while (!uart_tx_stopped(port) && !uart_circ_empty(xmit) && fifo_size) {
 846		iowrite8(xmit->buf[xmit->tail], priv->membase + PCH_UART_THR);
 847		uart_xmit_advance(port, 1);
 848		fifo_size--;
 849		tx_empty = 0;
 850	}
 851
 852	priv->tx_empty = tx_empty;
 853
 854	if (tx_empty) {
 855		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 856		uart_write_wakeup(port);
 857	}
 858
 859	return PCH_UART_HANDLED_TX_INT;
 860}
 861
 862static unsigned int dma_handle_tx(struct eg20t_port *priv)
 863{
 864	struct uart_port *port = &priv->port;
 865	struct circ_buf *xmit = &port->state->xmit;
 866	struct scatterlist *sg;
 867	int nent;
 868	int fifo_size;
 869	struct dma_async_tx_descriptor *desc;
 870	int num;
 871	int i;
 872	int bytes;
 873	int size;
 874	int rem;
 875
 876	if (!priv->start_tx) {
 877		dev_info(priv->port.dev, "%s:Tx isn't started. (%lu)\n",
 878			__func__, jiffies);
 879		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 880		priv->tx_empty = 1;
 881		return 0;
 882	}
 883
 884	if (priv->tx_dma_use) {
 885		dev_dbg(priv->port.dev, "%s:Tx is not completed. (%lu)\n",
 886			__func__, jiffies);
 887		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 888		priv->tx_empty = 1;
 889		return 0;
 890	}
 891
 892	fifo_size = max(priv->fifo_size, 1);
 893
 894	if (port->x_char) {
 895		iowrite8(port->x_char, priv->membase + PCH_UART_THR);
 896		port->icount.tx++;
 897		port->x_char = 0;
 898		fifo_size--;
 899	}
 900
 901	bytes = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
 902	if (!bytes) {
 903		dev_dbg(priv->port.dev, "%s 0 bytes return\n", __func__);
 904		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 905		uart_write_wakeup(port);
 906		return 0;
 907	}
 908
 909	if (bytes > fifo_size) {
 910		num = bytes / fifo_size + 1;
 911		size = fifo_size;
 912		rem = bytes % fifo_size;
 913	} else {
 914		num = 1;
 915		size = bytes;
 916		rem = bytes;
 917	}
 918
 919	dev_dbg(priv->port.dev, "%s num=%d size=%d rem=%d\n",
 920		__func__, num, size, rem);
 921
 922	priv->tx_dma_use = 1;
 923
 924	priv->sg_tx_p = kmalloc_array(num, sizeof(struct scatterlist), GFP_ATOMIC);
 925	if (!priv->sg_tx_p) {
 926		dev_err(priv->port.dev, "%s:kzalloc Failed\n", __func__);
 927		return 0;
 928	}
 929
 930	sg_init_table(priv->sg_tx_p, num); /* Initialize SG table */
 931	sg = priv->sg_tx_p;
 932
 933	for (i = 0; i < num; i++, sg++) {
 934		if (i == (num - 1))
 935			sg_set_page(sg, virt_to_page(xmit->buf),
 936				    rem, fifo_size * i);
 937		else
 938			sg_set_page(sg, virt_to_page(xmit->buf),
 939				    size, fifo_size * i);
 940	}
 941
 942	sg = priv->sg_tx_p;
 943	nent = dma_map_sg(port->dev, sg, num, DMA_TO_DEVICE);
 944	if (!nent) {
 945		dev_err(priv->port.dev, "%s:dma_map_sg Failed\n", __func__);
 946		return 0;
 947	}
 948	priv->orig_nent = num;
 949	priv->nent = nent;
 950
 951	for (i = 0; i < nent; i++, sg++) {
 952		sg->offset = (xmit->tail & (UART_XMIT_SIZE - 1)) +
 953			      fifo_size * i;
 954		sg_dma_address(sg) = (sg_dma_address(sg) &
 955				    ~(UART_XMIT_SIZE - 1)) + sg->offset;
 956		if (i == (nent - 1))
 957			sg_dma_len(sg) = rem;
 958		else
 959			sg_dma_len(sg) = size;
 960	}
 961
 962	desc = dmaengine_prep_slave_sg(priv->chan_tx,
 963					priv->sg_tx_p, nent, DMA_MEM_TO_DEV,
 964					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 965	if (!desc) {
 966		dev_err(priv->port.dev, "%s:dmaengine_prep_slave_sg Failed\n",
 967			__func__);
 968		return 0;
 969	}
 970	dma_sync_sg_for_device(port->dev, priv->sg_tx_p, nent, DMA_TO_DEVICE);
 971	priv->desc_tx = desc;
 972	desc->callback = pch_dma_tx_complete;
 973	desc->callback_param = priv;
 974
 975	desc->tx_submit(desc);
 976
 977	dma_async_issue_pending(priv->chan_tx);
 978
 979	return PCH_UART_HANDLED_TX_INT;
 980}
 981
 982static void pch_uart_err_ir(struct eg20t_port *priv, unsigned int lsr)
 983{
 984	struct uart_port *port = &priv->port;
 985	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
 986	char   *error_msg[5] = {};
 987	int    i = 0;
 988
 989	if (lsr & PCH_UART_LSR_ERR)
 990		error_msg[i++] = "Error data in FIFO\n";
 991
 992	if (lsr & UART_LSR_FE) {
 993		port->icount.frame++;
 994		error_msg[i++] = "  Framing Error\n";
 995	}
 996
 997	if (lsr & UART_LSR_PE) {
 998		port->icount.parity++;
 999		error_msg[i++] = "  Parity Error\n";
1000	}
1001
1002	if (lsr & UART_LSR_OE) {
1003		port->icount.overrun++;
1004		error_msg[i++] = "  Overrun Error\n";
1005	}
1006
1007	if (tty == NULL) {
1008		for (i = 0; error_msg[i] != NULL; i++)
1009			dev_err(&priv->pdev->dev, error_msg[i]);
1010	} else {
1011		tty_kref_put(tty);
1012	}
1013}
1014
1015static irqreturn_t pch_uart_interrupt(int irq, void *dev_id)
1016{
1017	struct eg20t_port *priv = dev_id;
1018	unsigned int handled;
1019	u8 lsr;
1020	int ret = 0;
1021	unsigned char iid;
1022	unsigned long flags;
1023	int next = 1;
1024	u8 msr;
1025
1026	spin_lock_irqsave(&priv->lock, flags);
1027	handled = 0;
1028	while (next) {
1029		iid = pch_uart_hal_get_iid(priv);
1030		if (iid & PCH_UART_IIR_IP) /* No Interrupt */
1031			break;
1032		switch (iid) {
1033		case PCH_UART_IID_RLS:	/* Receiver Line Status */
1034			lsr = pch_uart_hal_get_line_status(priv);
1035			if (lsr & (PCH_UART_LSR_ERR | UART_LSR_FE |
1036						UART_LSR_PE | UART_LSR_OE)) {
1037				pch_uart_err_ir(priv, lsr);
1038				ret = PCH_UART_HANDLED_RX_ERR_INT;
1039			} else {
1040				ret = PCH_UART_HANDLED_LS_INT;
1041			}
1042			break;
1043		case PCH_UART_IID_RDR:	/* Received Data Ready */
1044			if (priv->use_dma) {
1045				pch_uart_hal_disable_interrupt(priv,
1046						PCH_UART_HAL_RX_INT |
1047						PCH_UART_HAL_RX_ERR_INT);
1048				ret = dma_handle_rx(priv);
1049				if (!ret)
1050					pch_uart_hal_enable_interrupt(priv,
1051						PCH_UART_HAL_RX_INT |
1052						PCH_UART_HAL_RX_ERR_INT);
1053			} else {
1054				ret = handle_rx(priv);
1055			}
1056			break;
1057		case PCH_UART_IID_RDR_TO:	/* Received Data Ready
1058						   (FIFO Timeout) */
1059			ret = handle_rx_to(priv);
1060			break;
1061		case PCH_UART_IID_THRE:	/* Transmitter Holding Register
1062						   Empty */
1063			if (priv->use_dma)
1064				ret = dma_handle_tx(priv);
1065			else
1066				ret = handle_tx(priv);
1067			break;
1068		case PCH_UART_IID_MS:	/* Modem Status */
1069			msr = pch_uart_hal_get_modem(priv);
1070			next = 0; /* MS ir prioirty is the lowest. So, MS ir
1071				     means final interrupt */
1072			if ((msr & UART_MSR_ANY_DELTA) == 0)
1073				break;
1074			ret |= PCH_UART_HANDLED_MS_INT;
1075			break;
1076		default:	/* Never junp to this label */
1077			dev_err(priv->port.dev, "%s:iid=%02x (%lu)\n", __func__,
1078				iid, jiffies);
1079			ret = -1;
1080			next = 0;
1081			break;
1082		}
1083		handled |= (unsigned int)ret;
1084	}
1085
1086	spin_unlock_irqrestore(&priv->lock, flags);
1087	return IRQ_RETVAL(handled);
1088}
1089
1090/* This function tests whether the transmitter fifo and shifter for the port
1091						described by 'port' is empty. */
1092static unsigned int pch_uart_tx_empty(struct uart_port *port)
1093{
1094	struct eg20t_port *priv;
1095
1096	priv = container_of(port, struct eg20t_port, port);
1097	if (priv->tx_empty)
1098		return TIOCSER_TEMT;
1099	else
1100		return 0;
1101}
1102
1103/* Returns the current state of modem control inputs. */
1104static unsigned int pch_uart_get_mctrl(struct uart_port *port)
1105{
1106	struct eg20t_port *priv;
1107	u8 modem;
1108	unsigned int ret = 0;
1109
1110	priv = container_of(port, struct eg20t_port, port);
1111	modem = pch_uart_hal_get_modem(priv);
1112
1113	if (modem & UART_MSR_DCD)
1114		ret |= TIOCM_CAR;
1115
1116	if (modem & UART_MSR_RI)
1117		ret |= TIOCM_RNG;
1118
1119	if (modem & UART_MSR_DSR)
1120		ret |= TIOCM_DSR;
1121
1122	if (modem & UART_MSR_CTS)
1123		ret |= TIOCM_CTS;
1124
1125	return ret;
1126}
1127
1128static void pch_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1129{
1130	u32 mcr = 0;
1131	struct eg20t_port *priv = container_of(port, struct eg20t_port, port);
1132
1133	if (mctrl & TIOCM_DTR)
1134		mcr |= UART_MCR_DTR;
1135	if (mctrl & TIOCM_RTS)
1136		mcr |= UART_MCR_RTS;
1137	if (mctrl & TIOCM_LOOP)
1138		mcr |= UART_MCR_LOOP;
1139
1140	if (priv->mcr & UART_MCR_AFE)
1141		mcr |= UART_MCR_AFE;
1142
1143	if (mctrl)
1144		iowrite8(mcr, priv->membase + UART_MCR);
1145}
1146
1147static void pch_uart_stop_tx(struct uart_port *port)
1148{
1149	struct eg20t_port *priv;
1150	priv = container_of(port, struct eg20t_port, port);
1151	priv->start_tx = 0;
1152	priv->tx_dma_use = 0;
1153}
1154
1155static void pch_uart_start_tx(struct uart_port *port)
1156{
1157	struct eg20t_port *priv;
1158
1159	priv = container_of(port, struct eg20t_port, port);
1160
1161	if (priv->use_dma) {
1162		if (priv->tx_dma_use) {
1163			dev_dbg(priv->port.dev, "%s : Tx DMA is NOT empty.\n",
1164				__func__);
1165			return;
1166		}
1167	}
1168
1169	priv->start_tx = 1;
1170	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT);
1171}
1172
1173static void pch_uart_stop_rx(struct uart_port *port)
1174{
1175	struct eg20t_port *priv;
1176	priv = container_of(port, struct eg20t_port, port);
1177	priv->start_rx = 0;
1178	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT |
1179					     PCH_UART_HAL_RX_ERR_INT);
1180}
1181
1182/* Enable the modem status interrupts. */
1183static void pch_uart_enable_ms(struct uart_port *port)
1184{
1185	struct eg20t_port *priv;
1186	priv = container_of(port, struct eg20t_port, port);
1187	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_MS_INT);
1188}
1189
1190/* Control the transmission of a break signal. */
1191static void pch_uart_break_ctl(struct uart_port *port, int ctl)
1192{
1193	struct eg20t_port *priv;
1194	unsigned long flags;
1195
1196	priv = container_of(port, struct eg20t_port, port);
1197	spin_lock_irqsave(&priv->lock, flags);
1198	pch_uart_hal_set_break(priv, ctl);
1199	spin_unlock_irqrestore(&priv->lock, flags);
1200}
1201
1202/* Grab any interrupt resources and initialise any low level driver state. */
1203static int pch_uart_startup(struct uart_port *port)
1204{
1205	struct eg20t_port *priv;
1206	int ret;
1207	int fifo_size;
1208	int trigger_level;
1209
1210	priv = container_of(port, struct eg20t_port, port);
1211	priv->tx_empty = 1;
1212
1213	if (port->uartclk)
1214		priv->uartclk = port->uartclk;
1215	else
1216		port->uartclk = priv->uartclk;
1217
1218	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
1219	ret = pch_uart_hal_set_line(priv, default_baud,
1220			      PCH_UART_HAL_PARITY_NONE, PCH_UART_HAL_8BIT,
1221			      PCH_UART_HAL_STB1);
1222	if (ret)
1223		return ret;
1224
1225	switch (priv->fifo_size) {
1226	case 256:
1227		fifo_size = PCH_UART_HAL_FIFO256;
1228		break;
1229	case 64:
1230		fifo_size = PCH_UART_HAL_FIFO64;
1231		break;
1232	case 16:
1233		fifo_size = PCH_UART_HAL_FIFO16;
1234		break;
1235	case 1:
1236	default:
1237		fifo_size = PCH_UART_HAL_FIFO_DIS;
1238		break;
1239	}
1240
1241	switch (priv->trigger) {
1242	case PCH_UART_HAL_TRIGGER1:
1243		trigger_level = 1;
1244		break;
1245	case PCH_UART_HAL_TRIGGER_L:
1246		trigger_level = priv->fifo_size / 4;
1247		break;
1248	case PCH_UART_HAL_TRIGGER_M:
1249		trigger_level = priv->fifo_size / 2;
1250		break;
1251	case PCH_UART_HAL_TRIGGER_H:
1252	default:
1253		trigger_level = priv->fifo_size - (priv->fifo_size / 8);
1254		break;
1255	}
1256
1257	priv->trigger_level = trigger_level;
1258	ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0,
1259				    fifo_size, priv->trigger);
1260	if (ret < 0)
1261		return ret;
1262
1263	ret = request_irq(priv->port.irq, pch_uart_interrupt, IRQF_SHARED,
1264			priv->irq_name, priv);
1265	if (ret < 0)
1266		return ret;
1267
1268	if (priv->use_dma)
1269		pch_request_dma(port);
1270
1271	priv->start_rx = 1;
1272	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT |
1273					    PCH_UART_HAL_RX_ERR_INT);
1274	uart_update_timeout(port, CS8, default_baud);
1275
1276	return 0;
1277}
1278
1279static void pch_uart_shutdown(struct uart_port *port)
1280{
1281	struct eg20t_port *priv;
1282	int ret;
1283
1284	priv = container_of(port, struct eg20t_port, port);
1285	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
1286	pch_uart_hal_fifo_reset(priv, PCH_UART_HAL_CLR_ALL_FIFO);
1287	ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0,
1288			      PCH_UART_HAL_FIFO_DIS, PCH_UART_HAL_TRIGGER1);
1289	if (ret)
1290		dev_err(priv->port.dev,
1291			"pch_uart_hal_set_fifo Failed(ret=%d)\n", ret);
1292
1293	pch_free_dma(port);
1294
1295	free_irq(priv->port.irq, priv);
1296}
1297
1298/* Change the port parameters, including word length, parity, stop
1299 *bits.  Update read_status_mask and ignore_status_mask to indicate
1300 *the types of events we are interested in receiving.  */
1301static void pch_uart_set_termios(struct uart_port *port,
1302				 struct ktermios *termios,
1303				 const struct ktermios *old)
1304{
1305	int rtn;
1306	unsigned int baud, parity, bits, stb;
1307	struct eg20t_port *priv;
1308	unsigned long flags;
1309
1310	priv = container_of(port, struct eg20t_port, port);
1311	switch (termios->c_cflag & CSIZE) {
1312	case CS5:
1313		bits = PCH_UART_HAL_5BIT;
1314		break;
1315	case CS6:
1316		bits = PCH_UART_HAL_6BIT;
1317		break;
1318	case CS7:
1319		bits = PCH_UART_HAL_7BIT;
1320		break;
1321	default:		/* CS8 */
1322		bits = PCH_UART_HAL_8BIT;
1323		break;
1324	}
1325	if (termios->c_cflag & CSTOPB)
1326		stb = PCH_UART_HAL_STB2;
1327	else
1328		stb = PCH_UART_HAL_STB1;
1329
1330	if (termios->c_cflag & PARENB) {
1331		if (termios->c_cflag & PARODD)
1332			parity = PCH_UART_HAL_PARITY_ODD;
1333		else
1334			parity = PCH_UART_HAL_PARITY_EVEN;
1335
1336	} else
1337		parity = PCH_UART_HAL_PARITY_NONE;
1338
1339	/* Only UART0 has auto hardware flow function */
1340	if ((termios->c_cflag & CRTSCTS) && (priv->fifo_size == 256))
1341		priv->mcr |= UART_MCR_AFE;
1342	else
1343		priv->mcr &= ~UART_MCR_AFE;
1344
1345	termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */
1346
1347	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
1348
1349	spin_lock_irqsave(&priv->lock, flags);
1350	uart_port_lock(port);
1351
1352	uart_update_timeout(port, termios->c_cflag, baud);
1353	rtn = pch_uart_hal_set_line(priv, baud, parity, bits, stb);
1354	if (rtn)
1355		goto out;
1356
1357	pch_uart_set_mctrl(&priv->port, priv->port.mctrl);
1358	/* Don't rewrite B0 */
1359	if (tty_termios_baud_rate(termios))
1360		tty_termios_encode_baud_rate(termios, baud, baud);
1361
1362out:
1363	uart_port_unlock(port);
1364	spin_unlock_irqrestore(&priv->lock, flags);
1365}
1366
1367static const char *pch_uart_type(struct uart_port *port)
1368{
1369	return KBUILD_MODNAME;
1370}
1371
1372static void pch_uart_release_port(struct uart_port *port)
1373{
1374	struct eg20t_port *priv;
1375
1376	priv = container_of(port, struct eg20t_port, port);
1377	pci_iounmap(priv->pdev, priv->membase);
1378	pci_release_regions(priv->pdev);
1379}
1380
1381static int pch_uart_request_port(struct uart_port *port)
1382{
1383	struct eg20t_port *priv;
1384	int ret;
1385	void __iomem *membase;
1386
1387	priv = container_of(port, struct eg20t_port, port);
1388	ret = pci_request_regions(priv->pdev, KBUILD_MODNAME);
1389	if (ret < 0)
1390		return -EBUSY;
1391
1392	membase = pci_iomap(priv->pdev, 1, 0);
1393	if (!membase) {
1394		pci_release_regions(priv->pdev);
1395		return -EBUSY;
1396	}
1397	priv->membase = port->membase = membase;
1398
1399	return 0;
1400}
1401
1402static void pch_uart_config_port(struct uart_port *port, int type)
1403{
1404	struct eg20t_port *priv;
1405
1406	priv = container_of(port, struct eg20t_port, port);
1407	if (type & UART_CONFIG_TYPE) {
1408		port->type = priv->port_type;
1409		pch_uart_request_port(port);
1410	}
1411}
1412
1413static int pch_uart_verify_port(struct uart_port *port,
1414				struct serial_struct *serinfo)
1415{
1416	struct eg20t_port *priv;
1417
1418	priv = container_of(port, struct eg20t_port, port);
1419	if (serinfo->flags & UPF_LOW_LATENCY) {
1420		dev_info(priv->port.dev,
1421			"PCH UART : Use PIO Mode (without DMA)\n");
1422		priv->use_dma = 0;
1423		serinfo->flags &= ~UPF_LOW_LATENCY;
1424	} else {
1425#ifndef CONFIG_PCH_DMA
1426		dev_err(priv->port.dev, "%s : PCH DMA is not Loaded.\n",
1427			__func__);
1428		return -EOPNOTSUPP;
1429#endif
1430		if (!priv->use_dma) {
1431			pch_request_dma(port);
1432			if (priv->chan_rx)
1433				priv->use_dma = 1;
1434		}
1435		dev_info(priv->port.dev, "PCH UART: %s\n",
1436				priv->use_dma ?
1437				"Use DMA Mode" : "No DMA");
1438	}
1439
1440	return 0;
1441}
1442
1443#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_PCH_UART_CONSOLE)
1444/*
1445 *	Wait for transmitter & holding register to empty
1446 */
1447static void wait_for_xmitr(struct eg20t_port *up, int bits)
1448{
1449	unsigned int status, tmout = 10000;
1450
1451	/* Wait up to 10ms for the character(s) to be sent. */
1452	for (;;) {
1453		status = ioread8(up->membase + UART_LSR);
1454
1455		if ((status & bits) == bits)
1456			break;
1457		if (--tmout == 0)
1458			break;
1459		udelay(1);
1460	}
1461
1462	/* Wait up to 1s for flow control if necessary */
1463	if (up->port.flags & UPF_CONS_FLOW) {
1464		unsigned int tmout;
1465		for (tmout = 1000000; tmout; tmout--) {
1466			unsigned int msr = ioread8(up->membase + UART_MSR);
1467			if (msr & UART_MSR_CTS)
1468				break;
1469			udelay(1);
1470			touch_nmi_watchdog();
1471		}
1472	}
1473}
1474#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_PCH_UART_CONSOLE */
1475
1476#ifdef CONFIG_CONSOLE_POLL
1477/*
1478 * Console polling routines for communicate via uart while
1479 * in an interrupt or debug context.
1480 */
1481static int pch_uart_get_poll_char(struct uart_port *port)
1482{
1483	struct eg20t_port *priv =
1484		container_of(port, struct eg20t_port, port);
1485	u8 lsr = ioread8(priv->membase + UART_LSR);
1486
1487	if (!(lsr & UART_LSR_DR))
1488		return NO_POLL_CHAR;
1489
1490	return ioread8(priv->membase + PCH_UART_RBR);
1491}
1492
1493
1494static void pch_uart_put_poll_char(struct uart_port *port,
1495			 unsigned char c)
1496{
1497	unsigned int ier;
1498	struct eg20t_port *priv =
1499		container_of(port, struct eg20t_port, port);
1500
1501	/*
1502	 * First save the IER then disable the interrupts
1503	 */
1504	ier = ioread8(priv->membase + UART_IER);
1505	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
1506
1507	wait_for_xmitr(priv, UART_LSR_THRE);
1508	/*
1509	 * Send the character out.
1510	 */
1511	iowrite8(c, priv->membase + PCH_UART_THR);
1512
1513	/*
1514	 * Finally, wait for transmitter to become empty
1515	 * and restore the IER
1516	 */
1517	wait_for_xmitr(priv, UART_LSR_BOTH_EMPTY);
1518	iowrite8(ier, priv->membase + UART_IER);
1519}
1520#endif /* CONFIG_CONSOLE_POLL */
1521
1522static const struct uart_ops pch_uart_ops = {
1523	.tx_empty = pch_uart_tx_empty,
1524	.set_mctrl = pch_uart_set_mctrl,
1525	.get_mctrl = pch_uart_get_mctrl,
1526	.stop_tx = pch_uart_stop_tx,
1527	.start_tx = pch_uart_start_tx,
1528	.stop_rx = pch_uart_stop_rx,
1529	.enable_ms = pch_uart_enable_ms,
1530	.break_ctl = pch_uart_break_ctl,
1531	.startup = pch_uart_startup,
1532	.shutdown = pch_uart_shutdown,
1533	.set_termios = pch_uart_set_termios,
1534/*	.pm		= pch_uart_pm,		Not supported yet */
1535	.type = pch_uart_type,
1536	.release_port = pch_uart_release_port,
1537	.request_port = pch_uart_request_port,
1538	.config_port = pch_uart_config_port,
1539	.verify_port = pch_uart_verify_port,
1540#ifdef CONFIG_CONSOLE_POLL
1541	.poll_get_char = pch_uart_get_poll_char,
1542	.poll_put_char = pch_uart_put_poll_char,
1543#endif
1544};
1545
1546#ifdef CONFIG_SERIAL_PCH_UART_CONSOLE
1547
1548static void pch_console_putchar(struct uart_port *port, unsigned char ch)
1549{
1550	struct eg20t_port *priv =
1551		container_of(port, struct eg20t_port, port);
1552
1553	wait_for_xmitr(priv, UART_LSR_THRE);
1554	iowrite8(ch, priv->membase + PCH_UART_THR);
1555}
1556
1557/*
1558 *	Print a string to the serial port trying not to disturb
1559 *	any possible real use of the port...
1560 *
1561 *	The console_lock must be held when we get here.
1562 */
1563static void
1564pch_console_write(struct console *co, const char *s, unsigned int count)
1565{
1566	struct eg20t_port *priv;
1567	unsigned long flags;
1568	int priv_locked = 1;
1569	int port_locked = 1;
1570	u8 ier;
1571
1572	priv = pch_uart_ports[co->index];
1573
1574	touch_nmi_watchdog();
1575
1576	local_irq_save(flags);
1577	if (priv->port.sysrq) {
1578		/* call to uart_handle_sysrq_char already took the priv lock */
1579		priv_locked = 0;
1580		/* serial8250_handle_port() already took the port lock */
1581		port_locked = 0;
1582	} else if (oops_in_progress) {
1583		priv_locked = spin_trylock(&priv->lock);
1584		port_locked = uart_port_trylock(&priv->port);
1585	} else {
1586		spin_lock(&priv->lock);
1587		uart_port_lock(&priv->port);
1588	}
1589
1590	/*
1591	 *	First save the IER then disable the interrupts
1592	 */
1593	ier = ioread8(priv->membase + UART_IER);
1594
1595	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
1596
1597	uart_console_write(&priv->port, s, count, pch_console_putchar);
1598
1599	/*
1600	 *	Finally, wait for transmitter to become empty
1601	 *	and restore the IER
1602	 */
1603	wait_for_xmitr(priv, UART_LSR_BOTH_EMPTY);
1604	iowrite8(ier, priv->membase + UART_IER);
1605
1606	if (port_locked)
1607		uart_port_unlock(&priv->port);
1608	if (priv_locked)
1609		spin_unlock(&priv->lock);
1610	local_irq_restore(flags);
1611}
1612
1613static int __init pch_console_setup(struct console *co, char *options)
1614{
1615	struct uart_port *port;
1616	int baud = default_baud;
1617	int bits = 8;
1618	int parity = 'n';
1619	int flow = 'n';
1620
1621	/*
1622	 * Check whether an invalid uart number has been specified, and
1623	 * if so, search for the first available port that does have
1624	 * console support.
1625	 */
1626	if (co->index >= PCH_UART_NR)
1627		co->index = 0;
1628	port = &pch_uart_ports[co->index]->port;
1629
1630	if (!port || (!port->iobase && !port->membase))
1631		return -ENODEV;
1632
1633	port->uartclk = pch_uart_get_uartclk();
1634
1635	if (options)
1636		uart_parse_options(options, &baud, &parity, &bits, &flow);
1637
1638	return uart_set_options(port, co, baud, parity, bits, flow);
1639}
1640
1641static struct uart_driver pch_uart_driver;
1642
1643static struct console pch_console = {
1644	.name		= PCH_UART_DRIVER_DEVICE,
1645	.write		= pch_console_write,
1646	.device		= uart_console_device,
1647	.setup		= pch_console_setup,
1648	.flags		= CON_PRINTBUFFER | CON_ANYTIME,
1649	.index		= -1,
1650	.data		= &pch_uart_driver,
1651};
1652
1653#define PCH_CONSOLE	(&pch_console)
1654#else
1655#define PCH_CONSOLE	NULL
1656#endif	/* CONFIG_SERIAL_PCH_UART_CONSOLE */
1657
1658static struct uart_driver pch_uart_driver = {
1659	.owner = THIS_MODULE,
1660	.driver_name = KBUILD_MODNAME,
1661	.dev_name = PCH_UART_DRIVER_DEVICE,
1662	.major = 0,
1663	.minor = 0,
1664	.nr = PCH_UART_NR,
1665	.cons = PCH_CONSOLE,
1666};
1667
1668static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
1669					     const struct pci_device_id *id)
1670{
1671	struct eg20t_port *priv;
1672	int ret;
1673	unsigned int iobase;
1674	unsigned int mapbase;
1675	unsigned char *rxbuf;
1676	int fifosize;
1677	int port_type;
1678	struct pch_uart_driver_data *board;
1679	char name[32];
1680
1681	board = &drv_dat[id->driver_data];
1682	port_type = board->port_type;
1683
1684	priv = kzalloc(sizeof(struct eg20t_port), GFP_KERNEL);
1685	if (priv == NULL)
1686		goto init_port_alloc_err;
1687
1688	rxbuf = (unsigned char *)__get_free_page(GFP_KERNEL);
1689	if (!rxbuf)
1690		goto init_port_free_txbuf;
1691
1692	switch (port_type) {
1693	case PORT_PCH_8LINE:
1694		fifosize = 256; /* EG20T/ML7213: UART0 */
1695		break;
1696	case PORT_PCH_2LINE:
1697		fifosize = 64; /* EG20T:UART1~3  ML7213: UART1~2*/
1698		break;
1699	default:
1700		dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);
1701		goto init_port_hal_free;
1702	}
1703
1704	pci_enable_msi(pdev);
1705	pci_set_master(pdev);
1706
1707	spin_lock_init(&priv->lock);
1708
1709	iobase = pci_resource_start(pdev, 0);
1710	mapbase = pci_resource_start(pdev, 1);
1711	priv->mapbase = mapbase;
1712	priv->iobase = iobase;
1713	priv->pdev = pdev;
1714	priv->tx_empty = 1;
1715	priv->rxbuf.buf = rxbuf;
1716	priv->rxbuf.size = PAGE_SIZE;
1717
1718	priv->fifo_size = fifosize;
1719	priv->uartclk = pch_uart_get_uartclk();
1720	priv->port_type = port_type;
1721	priv->port.dev = &pdev->dev;
1722	priv->port.iobase = iobase;
1723	priv->port.membase = NULL;
1724	priv->port.mapbase = mapbase;
1725	priv->port.irq = pdev->irq;
1726	priv->port.iotype = UPIO_PORT;
1727	priv->port.ops = &pch_uart_ops;
1728	priv->port.flags = UPF_BOOT_AUTOCONF;
1729	priv->port.fifosize = fifosize;
1730	priv->port.line = board->line_no;
1731	priv->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_PCH_UART_CONSOLE);
1732	priv->trigger = PCH_UART_HAL_TRIGGER_M;
1733
1734	snprintf(priv->irq_name, IRQ_NAME_SIZE,
1735		 KBUILD_MODNAME ":" PCH_UART_DRIVER_DEVICE "%d",
1736		 priv->port.line);
1737
1738	spin_lock_init(&priv->port.lock);
1739
1740	pci_set_drvdata(pdev, priv);
1741	priv->trigger_level = 1;
1742	priv->fcr = 0;
1743
1744	if (pdev->dev.of_node)
1745		of_property_read_u32(pdev->dev.of_node, "clock-frequency"
1746					 , &user_uartclk);
1747
1748#ifdef CONFIG_SERIAL_PCH_UART_CONSOLE
1749	pch_uart_ports[board->line_no] = priv;
1750#endif
1751	ret = uart_add_one_port(&pch_uart_driver, &priv->port);
1752	if (ret < 0)
1753		goto init_port_hal_free;
1754
1755	snprintf(name, sizeof(name), "uart%d_regs", priv->port.line);
1756	debugfs_create_file(name, S_IFREG | S_IRUGO, NULL, priv,
1757			    &port_regs_ops);
1758
1759	return priv;
1760
1761init_port_hal_free:
1762#ifdef CONFIG_SERIAL_PCH_UART_CONSOLE
1763	pch_uart_ports[board->line_no] = NULL;
1764#endif
1765	free_page((unsigned long)rxbuf);
1766init_port_free_txbuf:
1767	kfree(priv);
1768init_port_alloc_err:
1769
1770	return NULL;
1771}
1772
1773static void pch_uart_exit_port(struct eg20t_port *priv)
1774{
1775	char name[32];
1776
1777	snprintf(name, sizeof(name), "uart%d_regs", priv->port.line);
1778	debugfs_lookup_and_remove(name, NULL);
1779	uart_remove_one_port(&pch_uart_driver, &priv->port);
1780	free_page((unsigned long)priv->rxbuf.buf);
1781}
1782
1783static void pch_uart_pci_remove(struct pci_dev *pdev)
1784{
1785	struct eg20t_port *priv = pci_get_drvdata(pdev);
1786
1787	pci_disable_msi(pdev);
1788
1789#ifdef CONFIG_SERIAL_PCH_UART_CONSOLE
1790	pch_uart_ports[priv->port.line] = NULL;
1791#endif
1792	pch_uart_exit_port(priv);
1793	pci_disable_device(pdev);
1794	kfree(priv);
1795	return;
1796}
1797
1798static int __maybe_unused pch_uart_pci_suspend(struct device *dev)
1799{
1800	struct eg20t_port *priv = dev_get_drvdata(dev);
1801
1802	uart_suspend_port(&pch_uart_driver, &priv->port);
1803
1804	return 0;
1805}
1806
1807static int __maybe_unused pch_uart_pci_resume(struct device *dev)
1808{
1809	struct eg20t_port *priv = dev_get_drvdata(dev);
1810
1811	uart_resume_port(&pch_uart_driver, &priv->port);
1812
1813	return 0;
1814}
1815
1816static const struct pci_device_id pch_uart_pci_id[] = {
1817	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8811),
1818	 .driver_data = pch_et20t_uart0},
1819	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8812),
1820	 .driver_data = pch_et20t_uart1},
1821	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8813),
1822	 .driver_data = pch_et20t_uart2},
1823	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8814),
1824	 .driver_data = pch_et20t_uart3},
1825	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8027),
1826	 .driver_data = pch_ml7213_uart0},
1827	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8028),
1828	 .driver_data = pch_ml7213_uart1},
1829	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8029),
1830	 .driver_data = pch_ml7213_uart2},
1831	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x800C),
1832	 .driver_data = pch_ml7223_uart0},
1833	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x800D),
1834	 .driver_data = pch_ml7223_uart1},
1835	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8811),
1836	 .driver_data = pch_ml7831_uart0},
1837	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8812),
1838	 .driver_data = pch_ml7831_uart1},
1839	{0,},
1840};
1841
1842static int pch_uart_pci_probe(struct pci_dev *pdev,
1843					const struct pci_device_id *id)
1844{
1845	int ret;
1846	struct eg20t_port *priv;
1847
1848	ret = pci_enable_device(pdev);
1849	if (ret < 0)
1850		goto probe_error;
1851
1852	priv = pch_uart_init_port(pdev, id);
1853	if (!priv) {
1854		ret = -EBUSY;
1855		goto probe_disable_device;
1856	}
1857	pci_set_drvdata(pdev, priv);
1858
1859	return ret;
1860
1861probe_disable_device:
1862	pci_disable_msi(pdev);
1863	pci_disable_device(pdev);
1864probe_error:
1865	return ret;
1866}
1867
1868static SIMPLE_DEV_PM_OPS(pch_uart_pci_pm_ops,
1869			 pch_uart_pci_suspend,
1870			 pch_uart_pci_resume);
1871
1872static struct pci_driver pch_uart_pci_driver = {
1873	.name = "pch_uart",
1874	.id_table = pch_uart_pci_id,
1875	.probe = pch_uart_pci_probe,
1876	.remove = pch_uart_pci_remove,
1877	.driver.pm = &pch_uart_pci_pm_ops,
1878};
1879
1880static int __init pch_uart_module_init(void)
1881{
1882	int ret;
1883
1884	/* register as UART driver */
1885	ret = uart_register_driver(&pch_uart_driver);
1886	if (ret < 0)
1887		return ret;
1888
1889	/* register as PCI driver */
1890	ret = pci_register_driver(&pch_uart_pci_driver);
1891	if (ret < 0)
1892		uart_unregister_driver(&pch_uart_driver);
1893
1894	return ret;
1895}
1896module_init(pch_uart_module_init);
1897
1898static void __exit pch_uart_module_exit(void)
1899{
1900	pci_unregister_driver(&pch_uart_pci_driver);
1901	uart_unregister_driver(&pch_uart_driver);
1902}
1903module_exit(pch_uart_module_exit);
1904
1905MODULE_LICENSE("GPL v2");
1906MODULE_DESCRIPTION("Intel EG20T PCH UART PCI Driver");
1907MODULE_DEVICE_TABLE(pci, pch_uart_pci_id);
1908
1909module_param(default_baud, uint, S_IRUGO);
1910MODULE_PARM_DESC(default_baud,
1911                 "Default BAUD for initial driver state and console (default 9600)");
1912module_param(user_uartclk, uint, S_IRUGO);
1913MODULE_PARM_DESC(user_uartclk,
1914                 "Override UART default or board specific UART clock");