Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * lm90.c - Part of lm_sensors, Linux kernel modules for hardware
4 * monitoring
5 * Copyright (C) 2003-2010 Jean Delvare <jdelvare@suse.de>
6 *
7 * Based on the lm83 driver. The LM90 is a sensor chip made by National
8 * Semiconductor. It reports up to two temperatures (its own plus up to
9 * one external one) with a 0.125 deg resolution (1 deg for local
10 * temperature) and a 3-4 deg accuracy.
11 *
12 * This driver also supports the LM89 and LM99, two other sensor chips
13 * made by National Semiconductor. Both have an increased remote
14 * temperature measurement accuracy (1 degree), and the LM99
15 * additionally shifts remote temperatures (measured and limits) by 16
16 * degrees, which allows for higher temperatures measurement.
17 * Note that there is no way to differentiate between both chips.
18 * When device is auto-detected, the driver will assume an LM99.
19 *
20 * This driver also supports the LM86, another sensor chip made by
21 * National Semiconductor. It is exactly similar to the LM90 except it
22 * has a higher accuracy.
23 *
24 * This driver also supports the ADM1032, a sensor chip made by Analog
25 * Devices. That chip is similar to the LM90, with a few differences
26 * that are not handled by this driver. Among others, it has a higher
27 * accuracy than the LM90, much like the LM86 does.
28 *
29 * This driver also supports the MAX6657, MAX6658 and MAX6659 sensor
30 * chips made by Maxim. These chips are similar to the LM86.
31 * Note that there is no easy way to differentiate between the three
32 * variants. We use the device address to detect MAX6659, which will result
33 * in a detection as max6657 if it is on address 0x4c. The extra address
34 * and features of the MAX6659 are only supported if the chip is configured
35 * explicitly as max6659, or if its address is not 0x4c.
36 * These chips lack the remote temperature offset feature.
37 *
38 * This driver also supports the MAX6654 chip made by Maxim. This chip can be
39 * at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is similar
40 * to MAX6657/MAX6658/MAX6659, but does not support critical temperature
41 * limits. Extended range is available by setting the configuration register
42 * accordingly, and is done during initialization. Extended precision is only
43 * available at conversion rates of 1 Hz and slower. Note that extended
44 * precision is not enabled by default, as this driver initializes all chips
45 * to 2 Hz by design. The driver also supports MAX6690, which is practically
46 * identical to MAX6654.
47 *
48 * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
49 * MAX6692 chips made by Maxim. These are again similar to the LM86,
50 * but they use unsigned temperature values and can report temperatures
51 * from 0 to 145 degrees.
52 *
53 * This driver also supports the MAX6680 and MAX6681, two other sensor
54 * chips made by Maxim. These are quite similar to the other Maxim
55 * chips. The MAX6680 and MAX6681 only differ in the pinout so they can
56 * be treated identically.
57 *
58 * This driver also supports the MAX6695 and MAX6696, two other sensor
59 * chips made by Maxim. These are also quite similar to other Maxim
60 * chips, but support three temperature sensors instead of two. MAX6695
61 * and MAX6696 only differ in the pinout so they can be treated identically.
62 *
63 * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as
64 * NCT1008 from ON Semiconductor. The chips are supported in both compatibility
65 * and extended mode. They are mostly compatible with LM90 except for a data
66 * format difference for the temperature value registers.
67 *
68 * This driver also supports ADT7481, ADT7482, and ADT7483 from Analog Devices
69 * / ON Semiconductor. The chips are similar to ADT7461 but support two external
70 * temperature sensors.
71 *
72 * This driver also supports NCT72, NCT214, and NCT218 from ON Semiconductor.
73 * The chips are similar to ADT7461/ADT7461A but have full PEC support
74 * (undocumented).
75 *
76 * This driver also supports the SA56004 from Philips. This device is
77 * pin-compatible with the LM86, the ED/EDP parts are also address-compatible.
78 *
79 * This driver also supports the G781 from GMT. This device is compatible
80 * with the ADM1032.
81 *
82 * This driver also supports TMP451 and TMP461 from Texas Instruments.
83 * Those devices are supported in both compatibility and extended mode.
84 * They are mostly compatible with ADT7461 except for local temperature
85 * low byte register and max conversion rate.
86 *
87 * This driver also supports MAX1617 and various clones such as G767
88 * and NE1617. Such clones will be detected as MAX1617.
89 *
90 * This driver also supports NE1618 from Philips. It is similar to NE1617
91 * but supports 11 bit external temperature values.
92 *
93 * Since the LM90 was the first chipset supported by this driver, most
94 * comments will refer to this chipset, but are actually general and
95 * concern all supported chipsets, unless mentioned otherwise.
96 */
97
98#include <linux/bits.h>
99#include <linux/device.h>
100#include <linux/err.h>
101#include <linux/i2c.h>
102#include <linux/init.h>
103#include <linux/interrupt.h>
104#include <linux/jiffies.h>
105#include <linux/hwmon.h>
106#include <linux/kstrtox.h>
107#include <linux/module.h>
108#include <linux/mutex.h>
109#include <linux/of.h>
110#include <linux/regulator/consumer.h>
111#include <linux/slab.h>
112#include <linux/workqueue.h>
113
114/* The maximum number of channels currently supported */
115#define MAX_CHANNELS 3
116
117/*
118 * Addresses to scan
119 * Address is fully defined internally and cannot be changed except for
120 * MAX6659, MAX6680 and MAX6681.
121 * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649,
122 * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c.
123 * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D
124 * have address 0x4d.
125 * MAX6647 has address 0x4e.
126 * MAX6659 can have address 0x4c, 0x4d or 0x4e.
127 * MAX6654, MAX6680, and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29,
128 * 0x2a, 0x2b, 0x4c, 0x4d or 0x4e.
129 * SA56004 can have address 0x48 through 0x4F.
130 */
131
132static const unsigned short normal_i2c[] = {
133 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x48, 0x49, 0x4a, 0x4b, 0x4c,
134 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
135
136enum chips { adm1023, adm1032, adt7461, adt7461a, adt7481,
137 g781, lm84, lm90, lm99,
138 max1617, max6642, max6646, max6648, max6654, max6657, max6659, max6680, max6696,
139 nct210, nct72, ne1618, sa56004, tmp451, tmp461, w83l771,
140};
141
142/*
143 * The LM90 registers
144 */
145
146#define LM90_REG_MAN_ID 0xFE
147#define LM90_REG_CHIP_ID 0xFF
148#define LM90_REG_CONFIG1 0x03
149#define LM90_REG_CONFIG2 0xBF
150#define LM90_REG_CONVRATE 0x04
151#define LM90_REG_STATUS 0x02
152#define LM90_REG_LOCAL_TEMP 0x00
153#define LM90_REG_LOCAL_HIGH 0x05
154#define LM90_REG_LOCAL_LOW 0x06
155#define LM90_REG_LOCAL_CRIT 0x20
156#define LM90_REG_REMOTE_TEMPH 0x01
157#define LM90_REG_REMOTE_TEMPL 0x10
158#define LM90_REG_REMOTE_OFFSH 0x11
159#define LM90_REG_REMOTE_OFFSL 0x12
160#define LM90_REG_REMOTE_HIGHH 0x07
161#define LM90_REG_REMOTE_HIGHL 0x13
162#define LM90_REG_REMOTE_LOWH 0x08
163#define LM90_REG_REMOTE_LOWL 0x14
164#define LM90_REG_REMOTE_CRIT 0x19
165#define LM90_REG_TCRIT_HYST 0x21
166
167/* MAX6646/6647/6649/6654/6657/6658/6659/6695/6696 registers */
168
169#define MAX6657_REG_LOCAL_TEMPL 0x11
170#define MAX6696_REG_STATUS2 0x12
171#define MAX6659_REG_REMOTE_EMERG 0x16
172#define MAX6659_REG_LOCAL_EMERG 0x17
173
174/* SA56004 registers */
175
176#define SA56004_REG_LOCAL_TEMPL 0x22
177
178#define LM90_MAX_CONVRATE_MS 16000 /* Maximum conversion rate in ms */
179
180/* TMP451/TMP461 registers */
181#define TMP451_REG_LOCAL_TEMPL 0x15
182#define TMP451_REG_CONALERT 0x22
183
184#define TMP461_REG_CHEN 0x16
185#define TMP461_REG_DFC 0x24
186
187/* ADT7481 registers */
188#define ADT7481_REG_STATUS2 0x23
189#define ADT7481_REG_CONFIG2 0x24
190
191#define ADT7481_REG_MAN_ID 0x3e
192#define ADT7481_REG_CHIP_ID 0x3d
193
194/* Device features */
195#define LM90_HAVE_EXTENDED_TEMP BIT(0) /* extended temperature support */
196#define LM90_HAVE_OFFSET BIT(1) /* temperature offset register */
197#define LM90_HAVE_UNSIGNED_TEMP BIT(2) /* temperatures are unsigned */
198#define LM90_HAVE_REM_LIMIT_EXT BIT(3) /* extended remote limit */
199#define LM90_HAVE_EMERGENCY BIT(4) /* 3rd upper (emergency) limit */
200#define LM90_HAVE_EMERGENCY_ALARM BIT(5)/* emergency alarm */
201#define LM90_HAVE_TEMP3 BIT(6) /* 3rd temperature sensor */
202#define LM90_HAVE_BROKEN_ALERT BIT(7) /* Broken alert */
203#define LM90_PAUSE_FOR_CONFIG BIT(8) /* Pause conversion for config */
204#define LM90_HAVE_CRIT BIT(9) /* Chip supports CRIT/OVERT register */
205#define LM90_HAVE_CRIT_ALRM_SWP BIT(10) /* critical alarm bits swapped */
206#define LM90_HAVE_PEC BIT(11) /* Chip supports PEC */
207#define LM90_HAVE_PARTIAL_PEC BIT(12) /* Partial PEC support (adm1032)*/
208#define LM90_HAVE_ALARMS BIT(13) /* Create 'alarms' attribute */
209#define LM90_HAVE_EXT_UNSIGNED BIT(14) /* extended unsigned temperature*/
210#define LM90_HAVE_LOW BIT(15) /* low limits */
211#define LM90_HAVE_CONVRATE BIT(16) /* conversion rate */
212#define LM90_HAVE_REMOTE_EXT BIT(17) /* extended remote temperature */
213#define LM90_HAVE_FAULTQUEUE BIT(18) /* configurable samples count */
214
215/* LM90 status */
216#define LM90_STATUS_LTHRM BIT(0) /* local THERM limit tripped */
217#define LM90_STATUS_RTHRM BIT(1) /* remote THERM limit tripped */
218#define LM90_STATUS_ROPEN BIT(2) /* remote is an open circuit */
219#define LM90_STATUS_RLOW BIT(3) /* remote low temp limit tripped */
220#define LM90_STATUS_RHIGH BIT(4) /* remote high temp limit tripped */
221#define LM90_STATUS_LLOW BIT(5) /* local low temp limit tripped */
222#define LM90_STATUS_LHIGH BIT(6) /* local high temp limit tripped */
223#define LM90_STATUS_BUSY BIT(7) /* conversion is ongoing */
224
225/* MAX6695/6696 and ADT7481 2nd status register */
226#define MAX6696_STATUS2_R2THRM BIT(1) /* remote2 THERM limit tripped */
227#define MAX6696_STATUS2_R2OPEN BIT(2) /* remote2 is an open circuit */
228#define MAX6696_STATUS2_R2LOW BIT(3) /* remote2 low temp limit tripped */
229#define MAX6696_STATUS2_R2HIGH BIT(4) /* remote2 high temp limit tripped */
230#define MAX6696_STATUS2_ROT2 BIT(5) /* remote emergency limit tripped */
231#define MAX6696_STATUS2_R2OT2 BIT(6) /* remote2 emergency limit tripped */
232#define MAX6696_STATUS2_LOT2 BIT(7) /* local emergency limit tripped */
233
234/*
235 * Driver data (common to all clients)
236 */
237
238static const struct i2c_device_id lm90_id[] = {
239 { "adm1020", max1617 },
240 { "adm1021", max1617 },
241 { "adm1023", adm1023 },
242 { "adm1032", adm1032 },
243 { "adt7421", adt7461a },
244 { "adt7461", adt7461 },
245 { "adt7461a", adt7461a },
246 { "adt7481", adt7481 },
247 { "adt7482", adt7481 },
248 { "adt7483a", adt7481 },
249 { "g781", g781 },
250 { "gl523sm", max1617 },
251 { "lm84", lm84 },
252 { "lm86", lm90 },
253 { "lm89", lm90 },
254 { "lm90", lm90 },
255 { "lm99", lm99 },
256 { "max1617", max1617 },
257 { "max6642", max6642 },
258 { "max6646", max6646 },
259 { "max6647", max6646 },
260 { "max6648", max6648 },
261 { "max6649", max6646 },
262 { "max6654", max6654 },
263 { "max6657", max6657 },
264 { "max6658", max6657 },
265 { "max6659", max6659 },
266 { "max6680", max6680 },
267 { "max6681", max6680 },
268 { "max6690", max6654 },
269 { "max6692", max6648 },
270 { "max6695", max6696 },
271 { "max6696", max6696 },
272 { "mc1066", max1617 },
273 { "nct1008", adt7461a },
274 { "nct210", nct210 },
275 { "nct214", nct72 },
276 { "nct218", nct72 },
277 { "nct72", nct72 },
278 { "ne1618", ne1618 },
279 { "w83l771", w83l771 },
280 { "sa56004", sa56004 },
281 { "thmc10", max1617 },
282 { "tmp451", tmp451 },
283 { "tmp461", tmp461 },
284 { }
285};
286MODULE_DEVICE_TABLE(i2c, lm90_id);
287
288static const struct of_device_id __maybe_unused lm90_of_match[] = {
289 {
290 .compatible = "adi,adm1032",
291 .data = (void *)adm1032
292 },
293 {
294 .compatible = "adi,adt7461",
295 .data = (void *)adt7461
296 },
297 {
298 .compatible = "adi,adt7461a",
299 .data = (void *)adt7461a
300 },
301 {
302 .compatible = "adi,adt7481",
303 .data = (void *)adt7481
304 },
305 {
306 .compatible = "gmt,g781",
307 .data = (void *)g781
308 },
309 {
310 .compatible = "national,lm90",
311 .data = (void *)lm90
312 },
313 {
314 .compatible = "national,lm86",
315 .data = (void *)lm90
316 },
317 {
318 .compatible = "national,lm89",
319 .data = (void *)lm90
320 },
321 {
322 .compatible = "national,lm99",
323 .data = (void *)lm99
324 },
325 {
326 .compatible = "dallas,max6646",
327 .data = (void *)max6646
328 },
329 {
330 .compatible = "dallas,max6647",
331 .data = (void *)max6646
332 },
333 {
334 .compatible = "dallas,max6649",
335 .data = (void *)max6646
336 },
337 {
338 .compatible = "dallas,max6654",
339 .data = (void *)max6654
340 },
341 {
342 .compatible = "dallas,max6657",
343 .data = (void *)max6657
344 },
345 {
346 .compatible = "dallas,max6658",
347 .data = (void *)max6657
348 },
349 {
350 .compatible = "dallas,max6659",
351 .data = (void *)max6659
352 },
353 {
354 .compatible = "dallas,max6680",
355 .data = (void *)max6680
356 },
357 {
358 .compatible = "dallas,max6681",
359 .data = (void *)max6680
360 },
361 {
362 .compatible = "dallas,max6695",
363 .data = (void *)max6696
364 },
365 {
366 .compatible = "dallas,max6696",
367 .data = (void *)max6696
368 },
369 {
370 .compatible = "onnn,nct1008",
371 .data = (void *)adt7461a
372 },
373 {
374 .compatible = "onnn,nct214",
375 .data = (void *)nct72
376 },
377 {
378 .compatible = "onnn,nct218",
379 .data = (void *)nct72
380 },
381 {
382 .compatible = "onnn,nct72",
383 .data = (void *)nct72
384 },
385 {
386 .compatible = "winbond,w83l771",
387 .data = (void *)w83l771
388 },
389 {
390 .compatible = "nxp,sa56004",
391 .data = (void *)sa56004
392 },
393 {
394 .compatible = "ti,tmp451",
395 .data = (void *)tmp451
396 },
397 {
398 .compatible = "ti,tmp461",
399 .data = (void *)tmp461
400 },
401 { },
402};
403MODULE_DEVICE_TABLE(of, lm90_of_match);
404
405/*
406 * chip type specific parameters
407 */
408struct lm90_params {
409 u32 flags; /* Capabilities */
410 u16 alert_alarms; /* Which alarm bits trigger ALERT# */
411 /* Upper 8 bits for max6695/96 */
412 u8 max_convrate; /* Maximum conversion rate register value */
413 u8 resolution; /* 16-bit resolution (default 11 bit) */
414 u8 reg_status2; /* 2nd status register (optional) */
415 u8 reg_local_ext; /* Extended local temp register (optional) */
416 u8 faultqueue_mask; /* fault queue bit mask */
417 u8 faultqueue_depth; /* fault queue depth if mask is used */
418};
419
420static const struct lm90_params lm90_params[] = {
421 [adm1023] = {
422 .flags = LM90_HAVE_ALARMS | LM90_HAVE_OFFSET | LM90_HAVE_BROKEN_ALERT
423 | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
424 | LM90_HAVE_REMOTE_EXT,
425 .alert_alarms = 0x7c,
426 .resolution = 8,
427 .max_convrate = 7,
428 },
429 [adm1032] = {
430 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
431 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT
432 | LM90_HAVE_PARTIAL_PEC | LM90_HAVE_ALARMS
433 | LM90_HAVE_LOW | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT
434 | LM90_HAVE_FAULTQUEUE,
435 .alert_alarms = 0x7c,
436 .max_convrate = 10,
437 },
438 [adt7461] = {
439 /*
440 * Standard temperature range is supposed to be unsigned,
441 * but that does not match reality. Negative temperatures
442 * are always reported.
443 */
444 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
445 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
446 | LM90_HAVE_CRIT | LM90_HAVE_PARTIAL_PEC
447 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
448 | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
449 .alert_alarms = 0x7c,
450 .max_convrate = 10,
451 .resolution = 10,
452 },
453 [adt7461a] = {
454 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
455 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
456 | LM90_HAVE_CRIT | LM90_HAVE_PEC | LM90_HAVE_ALARMS
457 | LM90_HAVE_LOW | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT
458 | LM90_HAVE_FAULTQUEUE,
459 .alert_alarms = 0x7c,
460 .max_convrate = 10,
461 },
462 [adt7481] = {
463 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
464 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
465 | LM90_HAVE_UNSIGNED_TEMP | LM90_HAVE_PEC
466 | LM90_HAVE_TEMP3 | LM90_HAVE_CRIT | LM90_HAVE_LOW
467 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT
468 | LM90_HAVE_FAULTQUEUE,
469 .alert_alarms = 0x1c7c,
470 .max_convrate = 11,
471 .resolution = 10,
472 .reg_status2 = ADT7481_REG_STATUS2,
473 },
474 [g781] = {
475 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
476 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT
477 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
478 | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
479 .alert_alarms = 0x7c,
480 .max_convrate = 7,
481 },
482 [lm84] = {
483 .flags = LM90_HAVE_ALARMS,
484 .resolution = 8,
485 },
486 [lm90] = {
487 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
488 | LM90_HAVE_CRIT | LM90_HAVE_ALARMS | LM90_HAVE_LOW
489 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT
490 | LM90_HAVE_FAULTQUEUE,
491 .alert_alarms = 0x7b,
492 .max_convrate = 9,
493 .faultqueue_mask = BIT(0),
494 .faultqueue_depth = 3,
495 },
496 [lm99] = {
497 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
498 | LM90_HAVE_CRIT | LM90_HAVE_ALARMS | LM90_HAVE_LOW
499 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT
500 | LM90_HAVE_FAULTQUEUE,
501 .alert_alarms = 0x7b,
502 .max_convrate = 9,
503 .faultqueue_mask = BIT(0),
504 .faultqueue_depth = 3,
505 },
506 [max1617] = {
507 .flags = LM90_HAVE_CONVRATE | LM90_HAVE_BROKEN_ALERT |
508 LM90_HAVE_LOW | LM90_HAVE_ALARMS,
509 .alert_alarms = 0x78,
510 .resolution = 8,
511 .max_convrate = 7,
512 },
513 [max6642] = {
514 .flags = LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXT_UNSIGNED
515 | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
516 .alert_alarms = 0x50,
517 .resolution = 10,
518 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
519 .faultqueue_mask = BIT(4),
520 .faultqueue_depth = 2,
521 },
522 [max6646] = {
523 .flags = LM90_HAVE_CRIT | LM90_HAVE_BROKEN_ALERT
524 | LM90_HAVE_EXT_UNSIGNED | LM90_HAVE_ALARMS | LM90_HAVE_LOW
525 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT,
526 .alert_alarms = 0x7c,
527 .max_convrate = 6,
528 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
529 },
530 [max6648] = {
531 .flags = LM90_HAVE_UNSIGNED_TEMP | LM90_HAVE_CRIT
532 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_LOW
533 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT,
534 .alert_alarms = 0x7c,
535 .max_convrate = 6,
536 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
537 },
538 [max6654] = {
539 .flags = LM90_HAVE_BROKEN_ALERT | LM90_HAVE_ALARMS | LM90_HAVE_LOW
540 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT,
541 .alert_alarms = 0x7c,
542 .max_convrate = 7,
543 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
544 },
545 [max6657] = {
546 .flags = LM90_PAUSE_FOR_CONFIG | LM90_HAVE_CRIT
547 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
548 | LM90_HAVE_REMOTE_EXT,
549 .alert_alarms = 0x7c,
550 .max_convrate = 8,
551 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
552 },
553 [max6659] = {
554 .flags = LM90_HAVE_EMERGENCY | LM90_HAVE_CRIT
555 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
556 | LM90_HAVE_REMOTE_EXT,
557 .alert_alarms = 0x7c,
558 .max_convrate = 8,
559 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
560 },
561 [max6680] = {
562 /*
563 * Apparent temperatures of 128 degrees C or higher are reported
564 * and treated as negative temperatures (meaning min_alarm will
565 * be set).
566 */
567 .flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT
568 | LM90_HAVE_CRIT_ALRM_SWP | LM90_HAVE_BROKEN_ALERT
569 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
570 | LM90_HAVE_REMOTE_EXT,
571 .alert_alarms = 0x7c,
572 .max_convrate = 7,
573 },
574 [max6696] = {
575 .flags = LM90_HAVE_EMERGENCY
576 | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3 | LM90_HAVE_CRIT
577 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
578 | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
579 .alert_alarms = 0x1c7c,
580 .max_convrate = 6,
581 .reg_status2 = MAX6696_REG_STATUS2,
582 .reg_local_ext = MAX6657_REG_LOCAL_TEMPL,
583 .faultqueue_mask = BIT(5),
584 .faultqueue_depth = 4,
585 },
586 [nct72] = {
587 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
588 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
589 | LM90_HAVE_CRIT | LM90_HAVE_PEC | LM90_HAVE_UNSIGNED_TEMP
590 | LM90_HAVE_LOW | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT
591 | LM90_HAVE_FAULTQUEUE,
592 .alert_alarms = 0x7c,
593 .max_convrate = 10,
594 .resolution = 10,
595 },
596 [nct210] = {
597 .flags = LM90_HAVE_ALARMS | LM90_HAVE_BROKEN_ALERT
598 | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
599 | LM90_HAVE_REMOTE_EXT,
600 .alert_alarms = 0x7c,
601 .resolution = 11,
602 .max_convrate = 7,
603 },
604 [ne1618] = {
605 .flags = LM90_PAUSE_FOR_CONFIG | LM90_HAVE_BROKEN_ALERT
606 | LM90_HAVE_LOW | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT,
607 .alert_alarms = 0x7c,
608 .resolution = 11,
609 .max_convrate = 7,
610 },
611 [w83l771] = {
612 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT
613 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
614 | LM90_HAVE_REMOTE_EXT,
615 .alert_alarms = 0x7c,
616 .max_convrate = 8,
617 },
618 [sa56004] = {
619 /*
620 * Apparent temperatures of 128 degrees C or higher are reported
621 * and treated as negative temperatures (meaning min_alarm will
622 * be set).
623 */
624 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT
625 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
626 | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
627 .alert_alarms = 0x7b,
628 .max_convrate = 9,
629 .reg_local_ext = SA56004_REG_LOCAL_TEMPL,
630 .faultqueue_mask = BIT(0),
631 .faultqueue_depth = 3,
632 },
633 [tmp451] = {
634 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
635 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT
636 | LM90_HAVE_UNSIGNED_TEMP | LM90_HAVE_ALARMS | LM90_HAVE_LOW
637 | LM90_HAVE_CONVRATE | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
638 .alert_alarms = 0x7c,
639 .max_convrate = 9,
640 .resolution = 12,
641 .reg_local_ext = TMP451_REG_LOCAL_TEMPL,
642 },
643 [tmp461] = {
644 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
645 | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT
646 | LM90_HAVE_ALARMS | LM90_HAVE_LOW | LM90_HAVE_CONVRATE
647 | LM90_HAVE_REMOTE_EXT | LM90_HAVE_FAULTQUEUE,
648 .alert_alarms = 0x7c,
649 .max_convrate = 9,
650 .resolution = 12,
651 .reg_local_ext = TMP451_REG_LOCAL_TEMPL,
652 },
653};
654
655/*
656 * temperature register index
657 */
658enum lm90_temp_reg_index {
659 LOCAL_LOW = 0,
660 LOCAL_HIGH,
661 LOCAL_CRIT,
662 REMOTE_CRIT,
663 LOCAL_EMERG, /* max6659 and max6695/96 */
664 REMOTE_EMERG, /* max6659 and max6695/96 */
665 REMOTE2_CRIT, /* max6695/96 only */
666 REMOTE2_EMERG, /* max6695/96 only */
667
668 REMOTE_TEMP,
669 REMOTE_LOW,
670 REMOTE_HIGH,
671 REMOTE_OFFSET, /* except max6646, max6657/58/59, and max6695/96 */
672 LOCAL_TEMP,
673 REMOTE2_TEMP, /* max6695/96 only */
674 REMOTE2_LOW, /* max6695/96 only */
675 REMOTE2_HIGH, /* max6695/96 only */
676 REMOTE2_OFFSET,
677
678 TEMP_REG_NUM
679};
680
681/*
682 * Client data (each client gets its own)
683 */
684
685struct lm90_data {
686 struct i2c_client *client;
687 struct device *hwmon_dev;
688 u32 chip_config[2];
689 u32 channel_config[MAX_CHANNELS + 1];
690 const char *channel_label[MAX_CHANNELS];
691 struct hwmon_channel_info chip_info;
692 struct hwmon_channel_info temp_info;
693 const struct hwmon_channel_info *info[3];
694 struct hwmon_chip_info chip;
695 struct mutex update_lock;
696 struct delayed_work alert_work;
697 struct work_struct report_work;
698 bool valid; /* true if register values are valid */
699 bool alarms_valid; /* true if status register values are valid */
700 unsigned long last_updated; /* in jiffies */
701 unsigned long alarms_updated; /* in jiffies */
702 int kind;
703 u32 flags;
704
705 unsigned int update_interval; /* in milliseconds */
706
707 u8 config; /* Current configuration register value */
708 u8 config_orig; /* Original configuration register value */
709 u8 convrate_orig; /* Original conversion rate register value */
710 u8 resolution; /* temperature resolution in bit */
711 u16 alert_alarms; /* Which alarm bits trigger ALERT# */
712 /* Upper 8 bits for max6695/96 */
713 u8 max_convrate; /* Maximum conversion rate */
714 u8 reg_status2; /* 2nd status register (optional) */
715 u8 reg_local_ext; /* local extension register offset */
716 u8 reg_remote_ext; /* remote temperature low byte */
717 u8 faultqueue_mask; /* fault queue mask */
718 u8 faultqueue_depth; /* fault queue mask */
719
720 /* registers values */
721 u16 temp[TEMP_REG_NUM];
722 u8 temp_hyst;
723 u8 conalert;
724 u16 reported_alarms; /* alarms reported as sysfs/udev events */
725 u16 current_alarms; /* current alarms, reported by chip */
726 u16 alarms; /* alarms not yet reported to user */
727};
728
729/*
730 * Support functions
731 */
732
733/*
734 * If the chip supports PEC but not on write byte transactions, we need
735 * to explicitly ask for a transaction without PEC.
736 */
737static inline s32 lm90_write_no_pec(struct i2c_client *client, u8 value)
738{
739 return i2c_smbus_xfer(client->adapter, client->addr,
740 client->flags & ~I2C_CLIENT_PEC,
741 I2C_SMBUS_WRITE, value, I2C_SMBUS_BYTE, NULL);
742}
743
744/*
745 * It is assumed that client->update_lock is held (unless we are in
746 * detection or initialization steps). This matters when PEC is enabled
747 * for chips with partial PEC support, because we don't want the address
748 * pointer to change between the write byte and the read byte transactions.
749 */
750static int lm90_read_reg(struct i2c_client *client, u8 reg)
751{
752 struct lm90_data *data = i2c_get_clientdata(client);
753 bool partial_pec = (client->flags & I2C_CLIENT_PEC) &&
754 (data->flags & LM90_HAVE_PARTIAL_PEC);
755 int err;
756
757 if (partial_pec) {
758 err = lm90_write_no_pec(client, reg);
759 if (err)
760 return err;
761 return i2c_smbus_read_byte(client);
762 }
763 return i2c_smbus_read_byte_data(client, reg);
764}
765
766/*
767 * Return register write address
768 *
769 * The write address for registers 0x03 .. 0x08 is the read address plus 6.
770 * For other registers the write address matches the read address.
771 */
772static u8 lm90_write_reg_addr(u8 reg)
773{
774 if (reg >= LM90_REG_CONFIG1 && reg <= LM90_REG_REMOTE_LOWH)
775 return reg + 6;
776 return reg;
777}
778
779/*
780 * Write into LM90 register.
781 * Convert register address to write address if needed, then execute the
782 * operation.
783 */
784static int lm90_write_reg(struct i2c_client *client, u8 reg, u8 val)
785{
786 return i2c_smbus_write_byte_data(client, lm90_write_reg_addr(reg), val);
787}
788
789/*
790 * Write into 16-bit LM90 register.
791 * Convert register addresses to write address if needed, then execute the
792 * operation.
793 */
794static int lm90_write16(struct i2c_client *client, u8 regh, u8 regl, u16 val)
795{
796 int ret;
797
798 ret = lm90_write_reg(client, regh, val >> 8);
799 if (ret < 0 || !regl)
800 return ret;
801 return lm90_write_reg(client, regl, val & 0xff);
802}
803
804static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl,
805 bool is_volatile)
806{
807 int oldh, newh, l;
808
809 oldh = lm90_read_reg(client, regh);
810 if (oldh < 0)
811 return oldh;
812
813 if (!regl)
814 return oldh << 8;
815
816 l = lm90_read_reg(client, regl);
817 if (l < 0)
818 return l;
819
820 if (!is_volatile)
821 return (oldh << 8) | l;
822
823 /*
824 * For volatile registers we have to use a trick.
825 * We have to read two registers to have the sensor temperature,
826 * but we have to beware a conversion could occur between the
827 * readings. The datasheet says we should either use
828 * the one-shot conversion register, which we don't want to do
829 * (disables hardware monitoring) or monitor the busy bit, which is
830 * impossible (we can't read the values and monitor that bit at the
831 * exact same time). So the solution used here is to read the high
832 * the high byte again. If the new high byte matches the old one,
833 * then we have a valid reading. Otherwise we have to read the low
834 * byte again, and now we believe we have a correct reading.
835 */
836 newh = lm90_read_reg(client, regh);
837 if (newh < 0)
838 return newh;
839 if (oldh != newh) {
840 l = lm90_read_reg(client, regl);
841 if (l < 0)
842 return l;
843 }
844 return (newh << 8) | l;
845}
846
847static int lm90_update_confreg(struct lm90_data *data, u8 config)
848{
849 if (data->config != config) {
850 int err;
851
852 err = lm90_write_reg(data->client, LM90_REG_CONFIG1, config);
853 if (err)
854 return err;
855 data->config = config;
856 }
857 return 0;
858}
859
860/*
861 * client->update_lock must be held when calling this function (unless we are
862 * in detection or initialization steps), and while a remote channel other
863 * than channel 0 is selected. Also, calling code must make sure to re-select
864 * external channel 0 before releasing the lock. This is necessary because
865 * various registers have different meanings as a result of selecting a
866 * non-default remote channel.
867 */
868static int lm90_select_remote_channel(struct lm90_data *data, bool second)
869{
870 u8 config = data->config & ~0x08;
871
872 if (second)
873 config |= 0x08;
874
875 return lm90_update_confreg(data, config);
876}
877
878static int lm90_write_convrate(struct lm90_data *data, int val)
879{
880 u8 config = data->config;
881 int err;
882
883 /* Save config and pause conversion */
884 if (data->flags & LM90_PAUSE_FOR_CONFIG) {
885 err = lm90_update_confreg(data, config | 0x40);
886 if (err < 0)
887 return err;
888 }
889
890 /* Set conv rate */
891 err = lm90_write_reg(data->client, LM90_REG_CONVRATE, val);
892
893 /* Revert change to config */
894 lm90_update_confreg(data, config);
895
896 return err;
897}
898
899/*
900 * Set conversion rate.
901 * client->update_lock must be held when calling this function (unless we are
902 * in detection or initialization steps).
903 */
904static int lm90_set_convrate(struct i2c_client *client, struct lm90_data *data,
905 unsigned int interval)
906{
907 unsigned int update_interval;
908 int i, err;
909
910 /* Shift calculations to avoid rounding errors */
911 interval <<= 6;
912
913 /* find the nearest update rate */
914 for (i = 0, update_interval = LM90_MAX_CONVRATE_MS << 6;
915 i < data->max_convrate; i++, update_interval >>= 1)
916 if (interval >= update_interval * 3 / 4)
917 break;
918
919 err = lm90_write_convrate(data, i);
920 data->update_interval = DIV_ROUND_CLOSEST(update_interval, 64);
921 return err;
922}
923
924static int lm90_set_faultqueue(struct i2c_client *client,
925 struct lm90_data *data, int val)
926{
927 int err;
928
929 if (data->faultqueue_mask) {
930 err = lm90_update_confreg(data, val <= data->faultqueue_depth / 2 ?
931 data->config & ~data->faultqueue_mask :
932 data->config | data->faultqueue_mask);
933 } else {
934 static const u8 values[4] = {0, 2, 6, 0x0e};
935
936 data->conalert = (data->conalert & 0xf1) | values[val - 1];
937 err = lm90_write_reg(data->client, TMP451_REG_CONALERT,
938 data->conalert);
939 }
940
941 return err;
942}
943
944static int lm90_update_limits(struct device *dev)
945{
946 struct lm90_data *data = dev_get_drvdata(dev);
947 struct i2c_client *client = data->client;
948 int val;
949
950 if (data->flags & LM90_HAVE_CRIT) {
951 val = lm90_read_reg(client, LM90_REG_LOCAL_CRIT);
952 if (val < 0)
953 return val;
954 data->temp[LOCAL_CRIT] = val << 8;
955
956 val = lm90_read_reg(client, LM90_REG_REMOTE_CRIT);
957 if (val < 0)
958 return val;
959 data->temp[REMOTE_CRIT] = val << 8;
960
961 val = lm90_read_reg(client, LM90_REG_TCRIT_HYST);
962 if (val < 0)
963 return val;
964 data->temp_hyst = val;
965 }
966 if ((data->flags & LM90_HAVE_FAULTQUEUE) && !data->faultqueue_mask) {
967 val = lm90_read_reg(client, TMP451_REG_CONALERT);
968 if (val < 0)
969 return val;
970 data->conalert = val;
971 }
972
973 val = lm90_read16(client, LM90_REG_REMOTE_LOWH,
974 (data->flags & LM90_HAVE_REM_LIMIT_EXT) ? LM90_REG_REMOTE_LOWL : 0,
975 false);
976 if (val < 0)
977 return val;
978 data->temp[REMOTE_LOW] = val;
979
980 val = lm90_read16(client, LM90_REG_REMOTE_HIGHH,
981 (data->flags & LM90_HAVE_REM_LIMIT_EXT) ? LM90_REG_REMOTE_HIGHL : 0,
982 false);
983 if (val < 0)
984 return val;
985 data->temp[REMOTE_HIGH] = val;
986
987 if (data->flags & LM90_HAVE_OFFSET) {
988 val = lm90_read16(client, LM90_REG_REMOTE_OFFSH,
989 LM90_REG_REMOTE_OFFSL, false);
990 if (val < 0)
991 return val;
992 data->temp[REMOTE_OFFSET] = val;
993 }
994
995 if (data->flags & LM90_HAVE_EMERGENCY) {
996 val = lm90_read_reg(client, MAX6659_REG_LOCAL_EMERG);
997 if (val < 0)
998 return val;
999 data->temp[LOCAL_EMERG] = val << 8;
1000
1001 val = lm90_read_reg(client, MAX6659_REG_REMOTE_EMERG);
1002 if (val < 0)
1003 return val;
1004 data->temp[REMOTE_EMERG] = val << 8;
1005 }
1006
1007 if (data->flags & LM90_HAVE_TEMP3) {
1008 val = lm90_select_remote_channel(data, true);
1009 if (val < 0)
1010 return val;
1011
1012 val = lm90_read_reg(client, LM90_REG_REMOTE_CRIT);
1013 if (val < 0)
1014 return val;
1015 data->temp[REMOTE2_CRIT] = val << 8;
1016
1017 if (data->flags & LM90_HAVE_EMERGENCY) {
1018 val = lm90_read_reg(client, MAX6659_REG_REMOTE_EMERG);
1019 if (val < 0)
1020 return val;
1021 data->temp[REMOTE2_EMERG] = val << 8;
1022 }
1023
1024 val = lm90_read_reg(client, LM90_REG_REMOTE_LOWH);
1025 if (val < 0)
1026 return val;
1027 data->temp[REMOTE2_LOW] = val << 8;
1028
1029 val = lm90_read_reg(client, LM90_REG_REMOTE_HIGHH);
1030 if (val < 0)
1031 return val;
1032 data->temp[REMOTE2_HIGH] = val << 8;
1033
1034 if (data->flags & LM90_HAVE_OFFSET) {
1035 val = lm90_read16(client, LM90_REG_REMOTE_OFFSH,
1036 LM90_REG_REMOTE_OFFSL, false);
1037 if (val < 0)
1038 return val;
1039 data->temp[REMOTE2_OFFSET] = val;
1040 }
1041
1042 lm90_select_remote_channel(data, false);
1043 }
1044
1045 return 0;
1046}
1047
1048static void lm90_report_alarms(struct work_struct *work)
1049{
1050 struct lm90_data *data = container_of(work, struct lm90_data, report_work);
1051 u16 cleared_alarms, new_alarms, current_alarms;
1052 struct device *hwmon_dev = data->hwmon_dev;
1053 struct device *dev = &data->client->dev;
1054 int st, st2;
1055
1056 current_alarms = data->current_alarms;
1057 cleared_alarms = data->reported_alarms & ~current_alarms;
1058 new_alarms = current_alarms & ~data->reported_alarms;
1059
1060 if (!cleared_alarms && !new_alarms)
1061 return;
1062
1063 st = new_alarms & 0xff;
1064 st2 = new_alarms >> 8;
1065
1066 if ((st & (LM90_STATUS_LLOW | LM90_STATUS_LHIGH | LM90_STATUS_LTHRM)) ||
1067 (st2 & MAX6696_STATUS2_LOT2))
1068 dev_dbg(dev, "temp%d out of range, please check!\n", 1);
1069 if ((st & (LM90_STATUS_RLOW | LM90_STATUS_RHIGH | LM90_STATUS_RTHRM)) ||
1070 (st2 & MAX6696_STATUS2_ROT2))
1071 dev_dbg(dev, "temp%d out of range, please check!\n", 2);
1072 if (st & LM90_STATUS_ROPEN)
1073 dev_dbg(dev, "temp%d diode open, please check!\n", 2);
1074 if (st2 & (MAX6696_STATUS2_R2LOW | MAX6696_STATUS2_R2HIGH |
1075 MAX6696_STATUS2_R2THRM | MAX6696_STATUS2_R2OT2))
1076 dev_dbg(dev, "temp%d out of range, please check!\n", 3);
1077 if (st2 & MAX6696_STATUS2_R2OPEN)
1078 dev_dbg(dev, "temp%d diode open, please check!\n", 3);
1079
1080 st |= cleared_alarms & 0xff;
1081 st2 |= cleared_alarms >> 8;
1082
1083 if (st & LM90_STATUS_LLOW)
1084 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_min_alarm, 0);
1085 if (st & LM90_STATUS_RLOW)
1086 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_min_alarm, 1);
1087 if (st2 & MAX6696_STATUS2_R2LOW)
1088 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_min_alarm, 2);
1089
1090 if (st & LM90_STATUS_LHIGH)
1091 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_max_alarm, 0);
1092 if (st & LM90_STATUS_RHIGH)
1093 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_max_alarm, 1);
1094 if (st2 & MAX6696_STATUS2_R2HIGH)
1095 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_max_alarm, 2);
1096
1097 if (st & LM90_STATUS_LTHRM)
1098 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_crit_alarm, 0);
1099 if (st & LM90_STATUS_RTHRM)
1100 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_crit_alarm, 1);
1101 if (st2 & MAX6696_STATUS2_R2THRM)
1102 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_crit_alarm, 2);
1103
1104 if (st2 & MAX6696_STATUS2_LOT2)
1105 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_emergency_alarm, 0);
1106 if (st2 & MAX6696_STATUS2_ROT2)
1107 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_emergency_alarm, 1);
1108 if (st2 & MAX6696_STATUS2_R2OT2)
1109 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_emergency_alarm, 2);
1110
1111 data->reported_alarms = current_alarms;
1112}
1113
1114static int lm90_update_alarms_locked(struct lm90_data *data, bool force)
1115{
1116 if (force || !data->alarms_valid ||
1117 time_after(jiffies, data->alarms_updated + msecs_to_jiffies(data->update_interval))) {
1118 struct i2c_client *client = data->client;
1119 bool check_enable;
1120 u16 alarms;
1121 int val;
1122
1123 data->alarms_valid = false;
1124
1125 val = lm90_read_reg(client, LM90_REG_STATUS);
1126 if (val < 0)
1127 return val;
1128 alarms = val & ~LM90_STATUS_BUSY;
1129
1130 if (data->reg_status2) {
1131 val = lm90_read_reg(client, data->reg_status2);
1132 if (val < 0)
1133 return val;
1134 alarms |= val << 8;
1135 }
1136 /*
1137 * If the update is forced (called from interrupt or alert
1138 * handler) and alarm data is valid, the alarms may have been
1139 * updated after the last update interval, and the status
1140 * register may still be cleared. Only add additional alarms
1141 * in this case. Alarms will be cleared later if appropriate.
1142 */
1143 if (force && data->alarms_valid)
1144 data->current_alarms |= alarms;
1145 else
1146 data->current_alarms = alarms;
1147 data->alarms |= alarms;
1148
1149 check_enable = (client->irq || !(data->config_orig & 0x80)) &&
1150 (data->config & 0x80);
1151
1152 if (force || check_enable)
1153 schedule_work(&data->report_work);
1154
1155 /*
1156 * Re-enable ALERT# output if it was originally enabled, relevant
1157 * alarms are all clear, and alerts are currently disabled.
1158 * Otherwise (re)schedule worker if needed.
1159 */
1160 if (check_enable) {
1161 if (!(data->current_alarms & data->alert_alarms)) {
1162 dev_dbg(&client->dev, "Re-enabling ALERT#\n");
1163 lm90_update_confreg(data, data->config & ~0x80);
1164 /*
1165 * We may have been called from the update handler.
1166 * If so, the worker, if scheduled, is no longer
1167 * needed. Cancel it. Don't synchronize because
1168 * it may already be running.
1169 */
1170 cancel_delayed_work(&data->alert_work);
1171 } else {
1172 schedule_delayed_work(&data->alert_work,
1173 max_t(int, HZ, msecs_to_jiffies(data->update_interval)));
1174 }
1175 }
1176 data->alarms_updated = jiffies;
1177 data->alarms_valid = true;
1178 }
1179 return 0;
1180}
1181
1182static int lm90_update_alarms(struct lm90_data *data, bool force)
1183{
1184 int err;
1185
1186 mutex_lock(&data->update_lock);
1187 err = lm90_update_alarms_locked(data, force);
1188 mutex_unlock(&data->update_lock);
1189
1190 return err;
1191}
1192
1193static void lm90_alert_work(struct work_struct *__work)
1194{
1195 struct delayed_work *delayed_work = container_of(__work, struct delayed_work, work);
1196 struct lm90_data *data = container_of(delayed_work, struct lm90_data, alert_work);
1197
1198 /* Nothing to do if alerts are enabled */
1199 if (!(data->config & 0x80))
1200 return;
1201
1202 lm90_update_alarms(data, true);
1203}
1204
1205static int lm90_update_device(struct device *dev)
1206{
1207 struct lm90_data *data = dev_get_drvdata(dev);
1208 struct i2c_client *client = data->client;
1209 unsigned long next_update;
1210 int val;
1211
1212 if (!data->valid) {
1213 val = lm90_update_limits(dev);
1214 if (val < 0)
1215 return val;
1216 }
1217
1218 next_update = data->last_updated +
1219 msecs_to_jiffies(data->update_interval);
1220 if (time_after(jiffies, next_update) || !data->valid) {
1221 dev_dbg(&client->dev, "Updating lm90 data.\n");
1222
1223 data->valid = false;
1224
1225 val = lm90_read_reg(client, LM90_REG_LOCAL_LOW);
1226 if (val < 0)
1227 return val;
1228 data->temp[LOCAL_LOW] = val << 8;
1229
1230 val = lm90_read_reg(client, LM90_REG_LOCAL_HIGH);
1231 if (val < 0)
1232 return val;
1233 data->temp[LOCAL_HIGH] = val << 8;
1234
1235 val = lm90_read16(client, LM90_REG_LOCAL_TEMP,
1236 data->reg_local_ext, true);
1237 if (val < 0)
1238 return val;
1239 data->temp[LOCAL_TEMP] = val;
1240 val = lm90_read16(client, LM90_REG_REMOTE_TEMPH,
1241 data->reg_remote_ext, true);
1242 if (val < 0)
1243 return val;
1244 data->temp[REMOTE_TEMP] = val;
1245
1246 if (data->flags & LM90_HAVE_TEMP3) {
1247 val = lm90_select_remote_channel(data, true);
1248 if (val < 0)
1249 return val;
1250
1251 val = lm90_read16(client, LM90_REG_REMOTE_TEMPH,
1252 data->reg_remote_ext, true);
1253 if (val < 0) {
1254 lm90_select_remote_channel(data, false);
1255 return val;
1256 }
1257 data->temp[REMOTE2_TEMP] = val;
1258
1259 lm90_select_remote_channel(data, false);
1260 }
1261
1262 val = lm90_update_alarms_locked(data, false);
1263 if (val < 0)
1264 return val;
1265
1266 data->last_updated = jiffies;
1267 data->valid = true;
1268 }
1269
1270 return 0;
1271}
1272
1273/* pec used for devices with PEC support */
1274static ssize_t pec_show(struct device *dev, struct device_attribute *dummy,
1275 char *buf)
1276{
1277 struct i2c_client *client = to_i2c_client(dev);
1278
1279 return sprintf(buf, "%d\n", !!(client->flags & I2C_CLIENT_PEC));
1280}
1281
1282static ssize_t pec_store(struct device *dev, struct device_attribute *dummy,
1283 const char *buf, size_t count)
1284{
1285 struct i2c_client *client = to_i2c_client(dev);
1286 long val;
1287 int err;
1288
1289 err = kstrtol(buf, 10, &val);
1290 if (err < 0)
1291 return err;
1292
1293 switch (val) {
1294 case 0:
1295 client->flags &= ~I2C_CLIENT_PEC;
1296 break;
1297 case 1:
1298 client->flags |= I2C_CLIENT_PEC;
1299 break;
1300 default:
1301 return -EINVAL;
1302 }
1303
1304 return count;
1305}
1306
1307static DEVICE_ATTR_RW(pec);
1308
1309static int lm90_temp_get_resolution(struct lm90_data *data, int index)
1310{
1311 switch (index) {
1312 case REMOTE_TEMP:
1313 if (data->reg_remote_ext)
1314 return data->resolution;
1315 return 8;
1316 case REMOTE_OFFSET:
1317 case REMOTE2_OFFSET:
1318 case REMOTE2_TEMP:
1319 return data->resolution;
1320 case LOCAL_TEMP:
1321 if (data->reg_local_ext)
1322 return data->resolution;
1323 return 8;
1324 case REMOTE_LOW:
1325 case REMOTE_HIGH:
1326 case REMOTE2_LOW:
1327 case REMOTE2_HIGH:
1328 if (data->flags & LM90_HAVE_REM_LIMIT_EXT)
1329 return data->resolution;
1330 return 8;
1331 default:
1332 return 8;
1333 }
1334}
1335
1336static int lm90_temp_from_reg(u32 flags, u16 regval, u8 resolution)
1337{
1338 int val;
1339
1340 if (flags & LM90_HAVE_EXTENDED_TEMP)
1341 val = regval - 0x4000;
1342 else if (flags & (LM90_HAVE_UNSIGNED_TEMP | LM90_HAVE_EXT_UNSIGNED))
1343 val = regval;
1344 else
1345 val = (s16)regval;
1346
1347 return ((val >> (16 - resolution)) * 1000) >> (resolution - 8);
1348}
1349
1350static int lm90_get_temp(struct lm90_data *data, int index, int channel)
1351{
1352 int temp = lm90_temp_from_reg(data->flags, data->temp[index],
1353 lm90_temp_get_resolution(data, index));
1354
1355 /* +16 degrees offset for remote temperature on LM99 */
1356 if (data->kind == lm99 && channel)
1357 temp += 16000;
1358
1359 return temp;
1360}
1361
1362static u16 lm90_temp_to_reg(u32 flags, long val, u8 resolution)
1363{
1364 int fraction = resolution > 8 ?
1365 1000 - DIV_ROUND_CLOSEST(1000, BIT(resolution - 8)) : 0;
1366
1367 if (flags & LM90_HAVE_EXTENDED_TEMP) {
1368 val = clamp_val(val, -64000, 191000 + fraction);
1369 val += 64000;
1370 } else if (flags & LM90_HAVE_EXT_UNSIGNED) {
1371 val = clamp_val(val, 0, 255000 + fraction);
1372 } else if (flags & LM90_HAVE_UNSIGNED_TEMP) {
1373 val = clamp_val(val, 0, 127000 + fraction);
1374 } else {
1375 val = clamp_val(val, -128000, 127000 + fraction);
1376 }
1377
1378 return DIV_ROUND_CLOSEST(val << (resolution - 8), 1000) << (16 - resolution);
1379}
1380
1381static int lm90_set_temp(struct lm90_data *data, int index, int channel, long val)
1382{
1383 static const u8 regs[] = {
1384 [LOCAL_LOW] = LM90_REG_LOCAL_LOW,
1385 [LOCAL_HIGH] = LM90_REG_LOCAL_HIGH,
1386 [LOCAL_CRIT] = LM90_REG_LOCAL_CRIT,
1387 [REMOTE_CRIT] = LM90_REG_REMOTE_CRIT,
1388 [LOCAL_EMERG] = MAX6659_REG_LOCAL_EMERG,
1389 [REMOTE_EMERG] = MAX6659_REG_REMOTE_EMERG,
1390 [REMOTE2_CRIT] = LM90_REG_REMOTE_CRIT,
1391 [REMOTE2_EMERG] = MAX6659_REG_REMOTE_EMERG,
1392 [REMOTE_LOW] = LM90_REG_REMOTE_LOWH,
1393 [REMOTE_HIGH] = LM90_REG_REMOTE_HIGHH,
1394 [REMOTE2_LOW] = LM90_REG_REMOTE_LOWH,
1395 [REMOTE2_HIGH] = LM90_REG_REMOTE_HIGHH,
1396 };
1397 struct i2c_client *client = data->client;
1398 u8 regh = regs[index];
1399 u8 regl = 0;
1400 int err;
1401
1402 if (channel && (data->flags & LM90_HAVE_REM_LIMIT_EXT)) {
1403 if (index == REMOTE_LOW || index == REMOTE2_LOW)
1404 regl = LM90_REG_REMOTE_LOWL;
1405 else if (index == REMOTE_HIGH || index == REMOTE2_HIGH)
1406 regl = LM90_REG_REMOTE_HIGHL;
1407 }
1408
1409 /* +16 degrees offset for remote temperature on LM99 */
1410 if (data->kind == lm99 && channel) {
1411 /* prevent integer underflow */
1412 val = max(val, -128000l);
1413 val -= 16000;
1414 }
1415
1416 data->temp[index] = lm90_temp_to_reg(data->flags, val,
1417 lm90_temp_get_resolution(data, index));
1418
1419 if (channel > 1)
1420 lm90_select_remote_channel(data, true);
1421
1422 err = lm90_write16(client, regh, regl, data->temp[index]);
1423
1424 if (channel > 1)
1425 lm90_select_remote_channel(data, false);
1426
1427 return err;
1428}
1429
1430static int lm90_get_temphyst(struct lm90_data *data, int index, int channel)
1431{
1432 int temp = lm90_get_temp(data, index, channel);
1433
1434 return temp - data->temp_hyst * 1000;
1435}
1436
1437static int lm90_set_temphyst(struct lm90_data *data, long val)
1438{
1439 int temp = lm90_get_temp(data, LOCAL_CRIT, 0);
1440
1441 /* prevent integer overflow/underflow */
1442 val = clamp_val(val, -128000l, 255000l);
1443 data->temp_hyst = clamp_val(DIV_ROUND_CLOSEST(temp - val, 1000), 0, 31);
1444
1445 return lm90_write_reg(data->client, LM90_REG_TCRIT_HYST, data->temp_hyst);
1446}
1447
1448static int lm90_get_temp_offset(struct lm90_data *data, int index)
1449{
1450 int res = lm90_temp_get_resolution(data, index);
1451
1452 return lm90_temp_from_reg(0, data->temp[index], res);
1453}
1454
1455static int lm90_set_temp_offset(struct lm90_data *data, int index, int channel, long val)
1456{
1457 int err;
1458
1459 val = lm90_temp_to_reg(0, val, lm90_temp_get_resolution(data, index));
1460
1461 /* For ADT7481 we can use the same registers for remote channel 1 and 2 */
1462 if (channel > 1)
1463 lm90_select_remote_channel(data, true);
1464
1465 err = lm90_write16(data->client, LM90_REG_REMOTE_OFFSH, LM90_REG_REMOTE_OFFSL, val);
1466
1467 if (channel > 1)
1468 lm90_select_remote_channel(data, false);
1469
1470 if (err)
1471 return err;
1472
1473 data->temp[index] = val;
1474
1475 return 0;
1476}
1477
1478static const u8 lm90_temp_index[MAX_CHANNELS] = {
1479 LOCAL_TEMP, REMOTE_TEMP, REMOTE2_TEMP
1480};
1481
1482static const u8 lm90_temp_min_index[MAX_CHANNELS] = {
1483 LOCAL_LOW, REMOTE_LOW, REMOTE2_LOW
1484};
1485
1486static const u8 lm90_temp_max_index[MAX_CHANNELS] = {
1487 LOCAL_HIGH, REMOTE_HIGH, REMOTE2_HIGH
1488};
1489
1490static const u8 lm90_temp_crit_index[MAX_CHANNELS] = {
1491 LOCAL_CRIT, REMOTE_CRIT, REMOTE2_CRIT
1492};
1493
1494static const u8 lm90_temp_emerg_index[MAX_CHANNELS] = {
1495 LOCAL_EMERG, REMOTE_EMERG, REMOTE2_EMERG
1496};
1497
1498static const s8 lm90_temp_offset_index[MAX_CHANNELS] = {
1499 -1, REMOTE_OFFSET, REMOTE2_OFFSET
1500};
1501
1502static const u16 lm90_min_alarm_bits[MAX_CHANNELS] = { BIT(5), BIT(3), BIT(11) };
1503static const u16 lm90_max_alarm_bits[MAX_CHANNELS] = { BIT(6), BIT(4), BIT(12) };
1504static const u16 lm90_crit_alarm_bits[MAX_CHANNELS] = { BIT(0), BIT(1), BIT(9) };
1505static const u16 lm90_crit_alarm_bits_swapped[MAX_CHANNELS] = { BIT(1), BIT(0), BIT(9) };
1506static const u16 lm90_emergency_alarm_bits[MAX_CHANNELS] = { BIT(15), BIT(13), BIT(14) };
1507static const u16 lm90_fault_bits[MAX_CHANNELS] = { BIT(0), BIT(2), BIT(10) };
1508
1509static int lm90_temp_read(struct device *dev, u32 attr, int channel, long *val)
1510{
1511 struct lm90_data *data = dev_get_drvdata(dev);
1512 int err;
1513 u16 bit;
1514
1515 mutex_lock(&data->update_lock);
1516 err = lm90_update_device(dev);
1517 mutex_unlock(&data->update_lock);
1518 if (err)
1519 return err;
1520
1521 switch (attr) {
1522 case hwmon_temp_input:
1523 *val = lm90_get_temp(data, lm90_temp_index[channel], channel);
1524 break;
1525 case hwmon_temp_min_alarm:
1526 case hwmon_temp_max_alarm:
1527 case hwmon_temp_crit_alarm:
1528 case hwmon_temp_emergency_alarm:
1529 case hwmon_temp_fault:
1530 switch (attr) {
1531 case hwmon_temp_min_alarm:
1532 bit = lm90_min_alarm_bits[channel];
1533 break;
1534 case hwmon_temp_max_alarm:
1535 bit = lm90_max_alarm_bits[channel];
1536 break;
1537 case hwmon_temp_crit_alarm:
1538 if (data->flags & LM90_HAVE_CRIT_ALRM_SWP)
1539 bit = lm90_crit_alarm_bits_swapped[channel];
1540 else
1541 bit = lm90_crit_alarm_bits[channel];
1542 break;
1543 case hwmon_temp_emergency_alarm:
1544 bit = lm90_emergency_alarm_bits[channel];
1545 break;
1546 case hwmon_temp_fault:
1547 bit = lm90_fault_bits[channel];
1548 break;
1549 }
1550 *val = !!(data->alarms & bit);
1551 data->alarms &= ~bit;
1552 data->alarms |= data->current_alarms;
1553 break;
1554 case hwmon_temp_min:
1555 *val = lm90_get_temp(data, lm90_temp_min_index[channel], channel);
1556 break;
1557 case hwmon_temp_max:
1558 *val = lm90_get_temp(data, lm90_temp_max_index[channel], channel);
1559 break;
1560 case hwmon_temp_crit:
1561 *val = lm90_get_temp(data, lm90_temp_crit_index[channel], channel);
1562 break;
1563 case hwmon_temp_crit_hyst:
1564 *val = lm90_get_temphyst(data, lm90_temp_crit_index[channel], channel);
1565 break;
1566 case hwmon_temp_emergency:
1567 *val = lm90_get_temp(data, lm90_temp_emerg_index[channel], channel);
1568 break;
1569 case hwmon_temp_emergency_hyst:
1570 *val = lm90_get_temphyst(data, lm90_temp_emerg_index[channel], channel);
1571 break;
1572 case hwmon_temp_offset:
1573 *val = lm90_get_temp_offset(data, lm90_temp_offset_index[channel]);
1574 break;
1575 default:
1576 return -EOPNOTSUPP;
1577 }
1578 return 0;
1579}
1580
1581static int lm90_temp_write(struct device *dev, u32 attr, int channel, long val)
1582{
1583 struct lm90_data *data = dev_get_drvdata(dev);
1584 int err;
1585
1586 mutex_lock(&data->update_lock);
1587
1588 err = lm90_update_device(dev);
1589 if (err)
1590 goto error;
1591
1592 switch (attr) {
1593 case hwmon_temp_min:
1594 err = lm90_set_temp(data, lm90_temp_min_index[channel],
1595 channel, val);
1596 break;
1597 case hwmon_temp_max:
1598 err = lm90_set_temp(data, lm90_temp_max_index[channel],
1599 channel, val);
1600 break;
1601 case hwmon_temp_crit:
1602 err = lm90_set_temp(data, lm90_temp_crit_index[channel],
1603 channel, val);
1604 break;
1605 case hwmon_temp_crit_hyst:
1606 err = lm90_set_temphyst(data, val);
1607 break;
1608 case hwmon_temp_emergency:
1609 err = lm90_set_temp(data, lm90_temp_emerg_index[channel],
1610 channel, val);
1611 break;
1612 case hwmon_temp_offset:
1613 err = lm90_set_temp_offset(data, lm90_temp_offset_index[channel],
1614 channel, val);
1615 break;
1616 default:
1617 err = -EOPNOTSUPP;
1618 break;
1619 }
1620error:
1621 mutex_unlock(&data->update_lock);
1622
1623 return err;
1624}
1625
1626static umode_t lm90_temp_is_visible(const void *data, u32 attr, int channel)
1627{
1628 switch (attr) {
1629 case hwmon_temp_input:
1630 case hwmon_temp_min_alarm:
1631 case hwmon_temp_max_alarm:
1632 case hwmon_temp_crit_alarm:
1633 case hwmon_temp_emergency_alarm:
1634 case hwmon_temp_emergency_hyst:
1635 case hwmon_temp_fault:
1636 case hwmon_temp_label:
1637 return 0444;
1638 case hwmon_temp_min:
1639 case hwmon_temp_max:
1640 case hwmon_temp_crit:
1641 case hwmon_temp_emergency:
1642 case hwmon_temp_offset:
1643 return 0644;
1644 case hwmon_temp_crit_hyst:
1645 if (channel == 0)
1646 return 0644;
1647 return 0444;
1648 default:
1649 return 0;
1650 }
1651}
1652
1653static int lm90_chip_read(struct device *dev, u32 attr, int channel, long *val)
1654{
1655 struct lm90_data *data = dev_get_drvdata(dev);
1656 int err;
1657
1658 mutex_lock(&data->update_lock);
1659 err = lm90_update_device(dev);
1660 mutex_unlock(&data->update_lock);
1661 if (err)
1662 return err;
1663
1664 switch (attr) {
1665 case hwmon_chip_update_interval:
1666 *val = data->update_interval;
1667 break;
1668 case hwmon_chip_alarms:
1669 *val = data->alarms;
1670 break;
1671 case hwmon_chip_temp_samples:
1672 if (data->faultqueue_mask) {
1673 *val = (data->config & data->faultqueue_mask) ?
1674 data->faultqueue_depth : 1;
1675 } else {
1676 switch (data->conalert & 0x0e) {
1677 case 0x0:
1678 default:
1679 *val = 1;
1680 break;
1681 case 0x2:
1682 *val = 2;
1683 break;
1684 case 0x6:
1685 *val = 3;
1686 break;
1687 case 0xe:
1688 *val = 4;
1689 break;
1690 }
1691 }
1692 break;
1693 default:
1694 return -EOPNOTSUPP;
1695 }
1696
1697 return 0;
1698}
1699
1700static int lm90_chip_write(struct device *dev, u32 attr, int channel, long val)
1701{
1702 struct lm90_data *data = dev_get_drvdata(dev);
1703 struct i2c_client *client = data->client;
1704 int err;
1705
1706 mutex_lock(&data->update_lock);
1707
1708 err = lm90_update_device(dev);
1709 if (err)
1710 goto error;
1711
1712 switch (attr) {
1713 case hwmon_chip_update_interval:
1714 err = lm90_set_convrate(client, data,
1715 clamp_val(val, 0, 100000));
1716 break;
1717 case hwmon_chip_temp_samples:
1718 err = lm90_set_faultqueue(client, data, clamp_val(val, 1, 4));
1719 break;
1720 default:
1721 err = -EOPNOTSUPP;
1722 break;
1723 }
1724error:
1725 mutex_unlock(&data->update_lock);
1726
1727 return err;
1728}
1729
1730static umode_t lm90_chip_is_visible(const void *data, u32 attr, int channel)
1731{
1732 switch (attr) {
1733 case hwmon_chip_update_interval:
1734 case hwmon_chip_temp_samples:
1735 return 0644;
1736 case hwmon_chip_alarms:
1737 return 0444;
1738 default:
1739 return 0;
1740 }
1741}
1742
1743static int lm90_read(struct device *dev, enum hwmon_sensor_types type,
1744 u32 attr, int channel, long *val)
1745{
1746 switch (type) {
1747 case hwmon_chip:
1748 return lm90_chip_read(dev, attr, channel, val);
1749 case hwmon_temp:
1750 return lm90_temp_read(dev, attr, channel, val);
1751 default:
1752 return -EOPNOTSUPP;
1753 }
1754}
1755
1756static int lm90_read_string(struct device *dev, enum hwmon_sensor_types type,
1757 u32 attr, int channel, const char **str)
1758{
1759 struct lm90_data *data = dev_get_drvdata(dev);
1760
1761 *str = data->channel_label[channel];
1762
1763 return 0;
1764}
1765
1766static int lm90_write(struct device *dev, enum hwmon_sensor_types type,
1767 u32 attr, int channel, long val)
1768{
1769 switch (type) {
1770 case hwmon_chip:
1771 return lm90_chip_write(dev, attr, channel, val);
1772 case hwmon_temp:
1773 return lm90_temp_write(dev, attr, channel, val);
1774 default:
1775 return -EOPNOTSUPP;
1776 }
1777}
1778
1779static umode_t lm90_is_visible(const void *data, enum hwmon_sensor_types type,
1780 u32 attr, int channel)
1781{
1782 switch (type) {
1783 case hwmon_chip:
1784 return lm90_chip_is_visible(data, attr, channel);
1785 case hwmon_temp:
1786 return lm90_temp_is_visible(data, attr, channel);
1787 default:
1788 return 0;
1789 }
1790}
1791
1792static const char *lm90_detect_lm84(struct i2c_client *client)
1793{
1794 static const u8 regs[] = {
1795 LM90_REG_STATUS, LM90_REG_LOCAL_TEMP, LM90_REG_LOCAL_HIGH,
1796 LM90_REG_REMOTE_TEMPH, LM90_REG_REMOTE_HIGHH
1797 };
1798 int status = i2c_smbus_read_byte_data(client, LM90_REG_STATUS);
1799 int reg1, reg2, reg3, reg4;
1800 bool nonzero = false;
1801 u8 ff = 0xff;
1802 int i;
1803
1804 if (status < 0 || (status & 0xab))
1805 return NULL;
1806
1807 /*
1808 * For LM84, undefined registers return the most recent value.
1809 * Repeat several times, each time checking against a different
1810 * (presumably) existing register.
1811 */
1812 for (i = 0; i < ARRAY_SIZE(regs); i++) {
1813 reg1 = i2c_smbus_read_byte_data(client, regs[i]);
1814 reg2 = i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_TEMPL);
1815 reg3 = i2c_smbus_read_byte_data(client, LM90_REG_LOCAL_LOW);
1816 reg4 = i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_LOWH);
1817
1818 if (reg1 < 0)
1819 return NULL;
1820
1821 /* If any register has a different value, this is not an LM84 */
1822 if (reg2 != reg1 || reg3 != reg1 || reg4 != reg1)
1823 return NULL;
1824
1825 nonzero |= reg1 || reg2 || reg3 || reg4;
1826 ff &= reg1;
1827 }
1828 /*
1829 * If all registers always returned 0 or 0xff, all bets are off,
1830 * and we can not make any predictions about the chip type.
1831 */
1832 return nonzero && ff != 0xff ? "lm84" : NULL;
1833}
1834
1835static const char *lm90_detect_max1617(struct i2c_client *client, int config1)
1836{
1837 int status = i2c_smbus_read_byte_data(client, LM90_REG_STATUS);
1838 int llo, rlo, lhi, rhi;
1839
1840 if (status < 0 || (status & 0x03))
1841 return NULL;
1842
1843 if (config1 & 0x3f)
1844 return NULL;
1845
1846 /*
1847 * Fail if unsupported registers return anything but 0xff.
1848 * The calling code already checked man_id and chip_id.
1849 * A byte read operation repeats the most recent read operation
1850 * and should also return 0xff.
1851 */
1852 if (i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_TEMPL) != 0xff ||
1853 i2c_smbus_read_byte_data(client, MAX6657_REG_LOCAL_TEMPL) != 0xff ||
1854 i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_LOWL) != 0xff ||
1855 i2c_smbus_read_byte(client) != 0xff)
1856 return NULL;
1857
1858 llo = i2c_smbus_read_byte_data(client, LM90_REG_LOCAL_LOW);
1859 rlo = i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_LOWH);
1860
1861 lhi = i2c_smbus_read_byte_data(client, LM90_REG_LOCAL_HIGH);
1862 rhi = i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_HIGHH);
1863
1864 if (llo < 0 || rlo < 0)
1865 return NULL;
1866
1867 /*
1868 * A byte read operation repeats the most recent read and should
1869 * return the same value.
1870 */
1871 if (i2c_smbus_read_byte(client) != rhi)
1872 return NULL;
1873
1874 /*
1875 * The following two checks are marginal since the checked values
1876 * are strictly speaking valid.
1877 */
1878
1879 /* fail for negative high limits; this also catches read errors */
1880 if ((s8)lhi < 0 || (s8)rhi < 0)
1881 return NULL;
1882
1883 /* fail if low limits are larger than or equal to high limits */
1884 if ((s8)llo >= lhi || (s8)rlo >= rhi)
1885 return NULL;
1886
1887 if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA)) {
1888 /*
1889 * Word read operations return 0xff in second byte
1890 */
1891 if (i2c_smbus_read_word_data(client, LM90_REG_REMOTE_TEMPL) !=
1892 0xffff)
1893 return NULL;
1894 if (i2c_smbus_read_word_data(client, LM90_REG_CONFIG1) !=
1895 (config1 | 0xff00))
1896 return NULL;
1897 if (i2c_smbus_read_word_data(client, LM90_REG_LOCAL_HIGH) !=
1898 (lhi | 0xff00))
1899 return NULL;
1900 }
1901
1902 return "max1617";
1903}
1904
1905static const char *lm90_detect_national(struct i2c_client *client, int chip_id,
1906 int config1, int convrate)
1907{
1908 int config2 = i2c_smbus_read_byte_data(client, LM90_REG_CONFIG2);
1909 int address = client->addr;
1910 const char *name = NULL;
1911
1912 if (config2 < 0)
1913 return NULL;
1914
1915 if ((config1 & 0x2a) || (config2 & 0xf8) || convrate > 0x09)
1916 return NULL;
1917
1918 if (address != 0x4c && address != 0x4d)
1919 return NULL;
1920
1921 switch (chip_id & 0xf0) {
1922 case 0x10: /* LM86 */
1923 if (address == 0x4c)
1924 name = "lm86";
1925 break;
1926 case 0x20: /* LM90 */
1927 if (address == 0x4c)
1928 name = "lm90";
1929 break;
1930 case 0x30: /* LM89/LM99 */
1931 name = "lm99"; /* detect LM89 as LM99 */
1932 break;
1933 default:
1934 break;
1935 }
1936
1937 return name;
1938}
1939
1940static const char *lm90_detect_on(struct i2c_client *client, int chip_id, int config1,
1941 int convrate)
1942{
1943 int address = client->addr;
1944 const char *name = NULL;
1945
1946 switch (chip_id) {
1947 case 0xca: /* NCT218 */
1948 if ((address == 0x4c || address == 0x4d) && !(config1 & 0x1b) &&
1949 convrate <= 0x0a)
1950 name = "nct218";
1951 break;
1952 default:
1953 break;
1954 }
1955 return name;
1956}
1957
1958static const char *lm90_detect_analog(struct i2c_client *client, bool common_address,
1959 int chip_id, int config1, int convrate)
1960{
1961 int status = i2c_smbus_read_byte_data(client, LM90_REG_STATUS);
1962 int config2 = i2c_smbus_read_byte_data(client, ADT7481_REG_CONFIG2);
1963 int man_id2 = i2c_smbus_read_byte_data(client, ADT7481_REG_MAN_ID);
1964 int chip_id2 = i2c_smbus_read_byte_data(client, ADT7481_REG_CHIP_ID);
1965 int address = client->addr;
1966 const char *name = NULL;
1967
1968 if (status < 0 || config2 < 0 || man_id2 < 0 || chip_id2 < 0)
1969 return NULL;
1970
1971 /*
1972 * The following chips should be detected by this function. Known
1973 * register values are listed. Registers 0x3d .. 0x3e are undocumented
1974 * for most of the chips, yet appear to return a well defined value.
1975 * Register 0xff is undocumented for some of the chips. Register 0x3f
1976 * is undocumented for all chips, but also returns a well defined value.
1977 * Values are as reported from real chips unless mentioned otherwise.
1978 * The code below checks values for registers 0x3d, 0x3e, and 0xff,
1979 * but not for register 0x3f.
1980 *
1981 * Chip Register
1982 * 3d 3e 3f fe ff Notes
1983 * ----------------------------------------------------------
1984 * adm1020 00 00 00 41 39
1985 * adm1021 00 00 00 41 03
1986 * adm1021a 00 00 00 41 3c
1987 * adm1023 00 00 00 41 3c same as adm1021a
1988 * adm1032 00 00 00 41 42
1989 *
1990 * adt7421 21 41 04 41 04
1991 * adt7461 00 00 00 41 51
1992 * adt7461a 61 41 05 41 57
1993 * adt7481 81 41 02 41 62
1994 * adt7482 - - - 41 65 datasheet
1995 * 82 41 05 41 75 real chip
1996 * adt7483 83 41 04 41 94
1997 *
1998 * nct72 61 41 07 41 55
1999 * nct210 00 00 00 41 3f
2000 * nct214 61 41 08 41 5a
2001 * nct1008 - - - 41 57 datasheet rev. 3
2002 * 61 41 06 41 54 real chip
2003 *
2004 * nvt210 - - - 41 - datasheet
2005 * nvt211 - - - 41 - datasheet
2006 */
2007 switch (chip_id) {
2008 case 0x00 ... 0x03: /* ADM1021 */
2009 case 0x05 ... 0x0f:
2010 if (man_id2 == 0x00 && chip_id2 == 0x00 && common_address &&
2011 !(status & 0x03) && !(config1 & 0x3f) && !(convrate & 0xf8))
2012 name = "adm1021";
2013 break;
2014 case 0x04: /* ADT7421 (undocumented) */
2015 if (man_id2 == 0x41 && chip_id2 == 0x21 &&
2016 (address == 0x4c || address == 0x4d) &&
2017 (config1 & 0x0b) == 0x08 && convrate <= 0x0a)
2018 name = "adt7421";
2019 break;
2020 case 0x30 ... 0x38: /* ADM1021A, ADM1023 */
2021 case 0x3a ... 0x3e:
2022 /*
2023 * ADM1021A and compatible chips will be mis-detected as
2024 * ADM1023. Chips labeled 'ADM1021A' and 'ADM1023' were both
2025 * found to have a Chip ID of 0x3c.
2026 * ADM1021A does not officially support low byte registers
2027 * (0x12 .. 0x14), but a chip labeled ADM1021A does support it.
2028 * Official support for the temperature offset high byte
2029 * register (0x11) was added to revision F of the ADM1021A
2030 * datasheet.
2031 * It is currently unknown if there is a means to distinguish
2032 * ADM1021A from ADM1023, and/or if revisions of ADM1021A exist
2033 * which differ in functionality from ADM1023.
2034 */
2035 if (man_id2 == 0x00 && chip_id2 == 0x00 && common_address &&
2036 !(status & 0x03) && !(config1 & 0x3f) && !(convrate & 0xf8))
2037 name = "adm1023";
2038 break;
2039 case 0x39: /* ADM1020 (undocumented) */
2040 if (man_id2 == 0x00 && chip_id2 == 0x00 &&
2041 (address == 0x4c || address == 0x4d || address == 0x4e) &&
2042 !(status & 0x03) && !(config1 & 0x3f) && !(convrate & 0xf8))
2043 name = "adm1020";
2044 break;
2045 case 0x3f: /* NCT210 */
2046 if (man_id2 == 0x00 && chip_id2 == 0x00 && common_address &&
2047 !(status & 0x03) && !(config1 & 0x3f) && !(convrate & 0xf8))
2048 name = "nct210";
2049 break;
2050 case 0x40 ... 0x4f: /* ADM1032 */
2051 if (man_id2 == 0x00 && chip_id2 == 0x00 &&
2052 (address == 0x4c || address == 0x4d) && !(config1 & 0x3f) &&
2053 convrate <= 0x0a)
2054 name = "adm1032";
2055 break;
2056 case 0x51: /* ADT7461 */
2057 if (man_id2 == 0x00 && chip_id2 == 0x00 &&
2058 (address == 0x4c || address == 0x4d) && !(config1 & 0x1b) &&
2059 convrate <= 0x0a)
2060 name = "adt7461";
2061 break;
2062 case 0x54: /* NCT1008 */
2063 if (man_id2 == 0x41 && chip_id2 == 0x61 &&
2064 (address == 0x4c || address == 0x4d) && !(config1 & 0x1b) &&
2065 convrate <= 0x0a)
2066 name = "nct1008";
2067 break;
2068 case 0x55: /* NCT72 */
2069 if (man_id2 == 0x41 && chip_id2 == 0x61 &&
2070 (address == 0x4c || address == 0x4d) && !(config1 & 0x1b) &&
2071 convrate <= 0x0a)
2072 name = "nct72";
2073 break;
2074 case 0x57: /* ADT7461A, NCT1008 (datasheet rev. 3) */
2075 if (man_id2 == 0x41 && chip_id2 == 0x61 &&
2076 (address == 0x4c || address == 0x4d) && !(config1 & 0x1b) &&
2077 convrate <= 0x0a)
2078 name = "adt7461a";
2079 break;
2080 case 0x5a: /* NCT214 */
2081 if (man_id2 == 0x41 && chip_id2 == 0x61 &&
2082 common_address && !(config1 & 0x1b) && convrate <= 0x0a)
2083 name = "nct214";
2084 break;
2085 case 0x62: /* ADT7481, undocumented */
2086 if (man_id2 == 0x41 && chip_id2 == 0x81 &&
2087 (address == 0x4b || address == 0x4c) && !(config1 & 0x10) &&
2088 !(config2 & 0x7f) && (convrate & 0x0f) <= 0x0b) {
2089 name = "adt7481";
2090 }
2091 break;
2092 case 0x65: /* ADT7482, datasheet */
2093 case 0x75: /* ADT7482, real chip */
2094 if (man_id2 == 0x41 && chip_id2 == 0x82 &&
2095 address == 0x4c && !(config1 & 0x10) && !(config2 & 0x7f) &&
2096 convrate <= 0x0a)
2097 name = "adt7482";
2098 break;
2099 case 0x94: /* ADT7483 */
2100 if (man_id2 == 0x41 && chip_id2 == 0x83 &&
2101 common_address &&
2102 ((address >= 0x18 && address <= 0x1a) ||
2103 (address >= 0x29 && address <= 0x2b) ||
2104 (address >= 0x4c && address <= 0x4e)) &&
2105 !(config1 & 0x10) && !(config2 & 0x7f) && convrate <= 0x0a)
2106 name = "adt7483a";
2107 break;
2108 default:
2109 break;
2110 }
2111
2112 return name;
2113}
2114
2115static const char *lm90_detect_maxim(struct i2c_client *client, bool common_address,
2116 int chip_id, int config1, int convrate)
2117{
2118 int man_id, emerg, emerg2, status2;
2119 int address = client->addr;
2120 const char *name = NULL;
2121
2122 switch (chip_id) {
2123 case 0x01:
2124 if (!common_address)
2125 break;
2126
2127 /*
2128 * We read MAX6659_REG_REMOTE_EMERG twice, and re-read
2129 * LM90_REG_MAN_ID in between. If MAX6659_REG_REMOTE_EMERG
2130 * exists, both readings will reflect the same value. Otherwise,
2131 * the readings will be different.
2132 */
2133 emerg = i2c_smbus_read_byte_data(client,
2134 MAX6659_REG_REMOTE_EMERG);
2135 man_id = i2c_smbus_read_byte_data(client,
2136 LM90_REG_MAN_ID);
2137 emerg2 = i2c_smbus_read_byte_data(client,
2138 MAX6659_REG_REMOTE_EMERG);
2139 status2 = i2c_smbus_read_byte_data(client,
2140 MAX6696_REG_STATUS2);
2141 if (emerg < 0 || man_id < 0 || emerg2 < 0 || status2 < 0)
2142 return NULL;
2143
2144 /*
2145 * Even though MAX6695 and MAX6696 do not have a chip ID
2146 * register, reading it returns 0x01. Bit 4 of the config1
2147 * register is unused and should return zero when read. Bit 0 of
2148 * the status2 register is unused and should return zero when
2149 * read.
2150 *
2151 * MAX6695 and MAX6696 have an additional set of temperature
2152 * limit registers. We can detect those chips by checking if
2153 * one of those registers exists.
2154 */
2155 if (!(config1 & 0x10) && !(status2 & 0x01) && emerg == emerg2 &&
2156 convrate <= 0x07)
2157 name = "max6696";
2158 /*
2159 * The chip_id register of the MAX6680 and MAX6681 holds the
2160 * revision of the chip. The lowest bit of the config1 register
2161 * is unused and should return zero when read, so should the
2162 * second to last bit of config1 (software reset). Register
2163 * address 0x12 (LM90_REG_REMOTE_OFFSL) exists for this chip and
2164 * should differ from emerg2, and emerg2 should match man_id
2165 * since it does not exist.
2166 */
2167 else if (!(config1 & 0x03) && convrate <= 0x07 &&
2168 emerg2 == man_id && emerg2 != status2)
2169 name = "max6680";
2170 /*
2171 * MAX1617A does not have any extended registers (register
2172 * address 0x10 or higher) except for manufacturer and
2173 * device ID registers. Unlike other chips of this series,
2174 * unsupported registers were observed to return a fixed value
2175 * of 0x01.
2176 * Note: Multiple chips with different markings labeled as
2177 * "MAX1617" (no "A") were observed to report manufacturer ID
2178 * 0x4d and device ID 0x01. It is unknown if other variants of
2179 * MAX1617/MAX617A with different behavior exist. The detection
2180 * code below works for those chips.
2181 */
2182 else if (!(config1 & 0x03f) && convrate <= 0x07 &&
2183 emerg == 0x01 && emerg2 == 0x01 && status2 == 0x01)
2184 name = "max1617";
2185 break;
2186 case 0x08:
2187 /*
2188 * The chip_id of the MAX6654 holds the revision of the chip.
2189 * The lowest 3 bits of the config1 register are unused and
2190 * should return zero when read.
2191 */
2192 if (common_address && !(config1 & 0x07) && convrate <= 0x07)
2193 name = "max6654";
2194 break;
2195 case 0x09:
2196 /*
2197 * The chip_id of the MAX6690 holds the revision of the chip.
2198 * The lowest 3 bits of the config1 register are unused and
2199 * should return zero when read.
2200 * Note that MAX6654 and MAX6690 are practically the same chips.
2201 * The only diference is the rated accuracy. Rev. 1 of the
2202 * MAX6690 datasheet lists a chip ID of 0x08, and a chip labeled
2203 * MAX6654 was observed to have a chip ID of 0x09.
2204 */
2205 if (common_address && !(config1 & 0x07) && convrate <= 0x07)
2206 name = "max6690";
2207 break;
2208 case 0x4d:
2209 /*
2210 * MAX6642, MAX6657, MAX6658 and MAX6659 do NOT have a chip_id
2211 * register. Reading from that address will return the last
2212 * read value, which in our case is those of the man_id
2213 * register, or 0x4d.
2214 * MAX6642 does not have a conversion rate register, nor low
2215 * limit registers. Reading from those registers returns the
2216 * last read value.
2217 *
2218 * For MAX6657, MAX6658 and MAX6659, the config1 register lacks
2219 * a low nibble, so the value will be those of the previous
2220 * read, so in our case again those of the man_id register.
2221 * MAX6659 has a third set of upper temperature limit registers.
2222 * Those registers also return values on MAX6657 and MAX6658,
2223 * thus the only way to detect MAX6659 is by its address.
2224 * For this reason it will be mis-detected as MAX6657 if its
2225 * address is 0x4c.
2226 */
2227 if (address >= 0x48 && address <= 0x4f && config1 == convrate &&
2228 !(config1 & 0x0f)) {
2229 int regval;
2230
2231 /*
2232 * We know that this is not a MAX6657/58/59 because its
2233 * configuration register has the wrong value and it does
2234 * not appear to have a conversion rate register.
2235 */
2236
2237 /* re-read manufacturer ID to have a good baseline */
2238 if (i2c_smbus_read_byte_data(client, LM90_REG_MAN_ID) != 0x4d)
2239 break;
2240
2241 /* check various non-existing registers */
2242 if (i2c_smbus_read_byte_data(client, LM90_REG_CONVRATE) != 0x4d ||
2243 i2c_smbus_read_byte_data(client, LM90_REG_LOCAL_LOW) != 0x4d ||
2244 i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_LOWH) != 0x4d)
2245 break;
2246
2247 /* check for unused status register bits */
2248 regval = i2c_smbus_read_byte_data(client, LM90_REG_STATUS);
2249 if (regval < 0 || (regval & 0x2b))
2250 break;
2251
2252 /* re-check unsupported registers */
2253 if (i2c_smbus_read_byte_data(client, LM90_REG_CONVRATE) != regval ||
2254 i2c_smbus_read_byte_data(client, LM90_REG_LOCAL_LOW) != regval ||
2255 i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_LOWH) != regval)
2256 break;
2257
2258 name = "max6642";
2259 } else if ((address == 0x4c || address == 0x4d || address == 0x4e) &&
2260 (config1 & 0x1f) == 0x0d && convrate <= 0x09) {
2261 if (address == 0x4c)
2262 name = "max6657";
2263 else
2264 name = "max6659";
2265 }
2266 break;
2267 case 0x59:
2268 /*
2269 * The chip_id register of the MAX6646/6647/6649 holds the
2270 * revision of the chip. The lowest 6 bits of the config1
2271 * register are unused and should return zero when read.
2272 * The I2C address of MAX6648/6692 is fixed at 0x4c.
2273 * MAX6646 is at address 0x4d, MAX6647 is at address 0x4e,
2274 * and MAX6649 is at address 0x4c. A slight difference between
2275 * the two sets of chips is that the remote temperature register
2276 * reports different values if the DXP pin is open or shorted.
2277 * We can use that information to help distinguish between the
2278 * chips. MAX6648 will be mis-detected as MAX6649 if the remote
2279 * diode is connected, but there isn't really anything we can
2280 * do about that.
2281 */
2282 if (!(config1 & 0x3f) && convrate <= 0x07) {
2283 int temp;
2284
2285 switch (address) {
2286 case 0x4c:
2287 /*
2288 * MAX6649 reports an external temperature
2289 * value of 0xff if DXP is open or shorted.
2290 * MAX6648 reports 0x80 in that case.
2291 */
2292 temp = i2c_smbus_read_byte_data(client,
2293 LM90_REG_REMOTE_TEMPH);
2294 if (temp == 0x80)
2295 name = "max6648";
2296 else
2297 name = "max6649";
2298 break;
2299 case 0x4d:
2300 name = "max6646";
2301 break;
2302 case 0x4e:
2303 name = "max6647";
2304 break;
2305 default:
2306 break;
2307 }
2308 }
2309 break;
2310 default:
2311 break;
2312 }
2313
2314 return name;
2315}
2316
2317static const char *lm90_detect_nuvoton(struct i2c_client *client, int chip_id,
2318 int config1, int convrate)
2319{
2320 int config2 = i2c_smbus_read_byte_data(client, LM90_REG_CONFIG2);
2321 int address = client->addr;
2322 const char *name = NULL;
2323
2324 if (config2 < 0)
2325 return NULL;
2326
2327 if (address == 0x4c && !(config1 & 0x2a) && !(config2 & 0xf8)) {
2328 if (chip_id == 0x01 && convrate <= 0x09) {
2329 /* W83L771W/G */
2330 name = "w83l771";
2331 } else if ((chip_id & 0xfe) == 0x10 && convrate <= 0x08) {
2332 /* W83L771AWG/ASG */
2333 name = "w83l771";
2334 }
2335 }
2336 return name;
2337}
2338
2339static const char *lm90_detect_nxp(struct i2c_client *client, bool common_address,
2340 int chip_id, int config1, int convrate)
2341{
2342 int address = client->addr;
2343 const char *name = NULL;
2344 int config2;
2345
2346 switch (chip_id) {
2347 case 0x00:
2348 config2 = i2c_smbus_read_byte_data(client, LM90_REG_CONFIG2);
2349 if (config2 < 0)
2350 return NULL;
2351 if (address >= 0x48 && address <= 0x4f &&
2352 !(config1 & 0x2a) && !(config2 & 0xfe) && convrate <= 0x09)
2353 name = "sa56004";
2354 break;
2355 case 0x80:
2356 if (common_address && !(config1 & 0x3f) && convrate <= 0x07)
2357 name = "ne1618";
2358 break;
2359 default:
2360 break;
2361 }
2362 return name;
2363}
2364
2365static const char *lm90_detect_gmt(struct i2c_client *client, int chip_id,
2366 int config1, int convrate)
2367{
2368 int address = client->addr;
2369
2370 /*
2371 * According to the datasheet, G781 is supposed to be at I2C Address
2372 * 0x4c and have a chip ID of 0x01. G781-1 is supposed to be at I2C
2373 * address 0x4d and have a chip ID of 0x03. However, when support
2374 * for G781 was added, chips at 0x4c and 0x4d were found to have a
2375 * chip ID of 0x01. A G781-1 at I2C address 0x4d was now found with
2376 * chip ID 0x03.
2377 * To avoid detection failures, accept chip ID 0x01 and 0x03 at both
2378 * addresses.
2379 * G784 reports manufacturer ID 0x47 and chip ID 0x01. A public
2380 * datasheet is not available. Extensive testing suggests that
2381 * the chip appears to be fully compatible with G781.
2382 * Available register dumps show that G751 also reports manufacturer
2383 * ID 0x47 and chip ID 0x01 even though that chip does not officially
2384 * support those registers. This makes chip detection somewhat
2385 * vulnerable. To improve detection quality, read the offset low byte
2386 * and alert fault queue registers and verify that only expected bits
2387 * are set.
2388 */
2389 if ((chip_id == 0x01 || chip_id == 0x03) &&
2390 (address == 0x4c || address == 0x4d) &&
2391 !(config1 & 0x3f) && convrate <= 0x08) {
2392 int reg;
2393
2394 reg = i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_OFFSL);
2395 if (reg < 0 || reg & 0x1f)
2396 return NULL;
2397 reg = i2c_smbus_read_byte_data(client, TMP451_REG_CONALERT);
2398 if (reg < 0 || reg & 0xf1)
2399 return NULL;
2400
2401 return "g781";
2402 }
2403
2404 return NULL;
2405}
2406
2407static const char *lm90_detect_ti49(struct i2c_client *client, bool common_address,
2408 int chip_id, int config1, int convrate)
2409{
2410 if (common_address && chip_id == 0x00 && !(config1 & 0x3f) && !(convrate & 0xf8)) {
2411 /* THMC10: Unsupported registers return 0xff */
2412 if (i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_TEMPL) == 0xff &&
2413 i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_CRIT) == 0xff)
2414 return "thmc10";
2415 }
2416 return NULL;
2417}
2418
2419static const char *lm90_detect_ti(struct i2c_client *client, int chip_id,
2420 int config1, int convrate)
2421{
2422 int address = client->addr;
2423 const char *name = NULL;
2424
2425 if (chip_id == 0x00 && !(config1 & 0x1b) && convrate <= 0x09) {
2426 int local_ext, conalert, chen, dfc;
2427
2428 local_ext = i2c_smbus_read_byte_data(client,
2429 TMP451_REG_LOCAL_TEMPL);
2430 conalert = i2c_smbus_read_byte_data(client,
2431 TMP451_REG_CONALERT);
2432 chen = i2c_smbus_read_byte_data(client, TMP461_REG_CHEN);
2433 dfc = i2c_smbus_read_byte_data(client, TMP461_REG_DFC);
2434
2435 if (!(local_ext & 0x0f) && (conalert & 0xf1) == 0x01 &&
2436 (chen & 0xfc) == 0x00 && (dfc & 0xfc) == 0x00) {
2437 if (address == 0x4c && !(chen & 0x03))
2438 name = "tmp451";
2439 else if (address >= 0x48 && address <= 0x4f)
2440 name = "tmp461";
2441 }
2442 }
2443
2444 return name;
2445}
2446
2447/* Return 0 if detection is successful, -ENODEV otherwise */
2448static int lm90_detect(struct i2c_client *client, struct i2c_board_info *info)
2449{
2450 struct i2c_adapter *adapter = client->adapter;
2451 int man_id, chip_id, config1, convrate, lhigh;
2452 const char *name = NULL;
2453 int address = client->addr;
2454 bool common_address =
2455 (address >= 0x18 && address <= 0x1a) ||
2456 (address >= 0x29 && address <= 0x2b) ||
2457 (address >= 0x4c && address <= 0x4e);
2458
2459 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
2460 return -ENODEV;
2461
2462 /*
2463 * Get well defined register value for chips with neither man_id nor
2464 * chip_id registers.
2465 */
2466 lhigh = i2c_smbus_read_byte_data(client, LM90_REG_LOCAL_HIGH);
2467
2468 /* detection and identification */
2469 man_id = i2c_smbus_read_byte_data(client, LM90_REG_MAN_ID);
2470 chip_id = i2c_smbus_read_byte_data(client, LM90_REG_CHIP_ID);
2471 config1 = i2c_smbus_read_byte_data(client, LM90_REG_CONFIG1);
2472 convrate = i2c_smbus_read_byte_data(client, LM90_REG_CONVRATE);
2473 if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0 || lhigh < 0)
2474 return -ENODEV;
2475
2476 /* Bail out immediately if all register report the same value */
2477 if (lhigh == man_id && lhigh == chip_id && lhigh == config1 && lhigh == convrate)
2478 return -ENODEV;
2479
2480 /*
2481 * If reading man_id and chip_id both return the same value as lhigh,
2482 * the chip may not support those registers and return the most recent read
2483 * value. Check again with a different register and handle accordingly.
2484 */
2485 if (man_id == lhigh && chip_id == lhigh) {
2486 convrate = i2c_smbus_read_byte_data(client, LM90_REG_CONVRATE);
2487 man_id = i2c_smbus_read_byte_data(client, LM90_REG_MAN_ID);
2488 chip_id = i2c_smbus_read_byte_data(client, LM90_REG_CHIP_ID);
2489 if (convrate < 0 || man_id < 0 || chip_id < 0)
2490 return -ENODEV;
2491 if (man_id == convrate && chip_id == convrate)
2492 man_id = -1;
2493 }
2494 switch (man_id) {
2495 case -1: /* Chip does not support man_id / chip_id */
2496 if (common_address && !convrate && !(config1 & 0x7f))
2497 name = lm90_detect_lm84(client);
2498 break;
2499 case 0x01: /* National Semiconductor */
2500 name = lm90_detect_national(client, chip_id, config1, convrate);
2501 break;
2502 case 0x1a: /* ON */
2503 name = lm90_detect_on(client, chip_id, config1, convrate);
2504 break;
2505 case 0x23: /* Genesys Logic */
2506 if (common_address && !(config1 & 0x3f) && !(convrate & 0xf8))
2507 name = "gl523sm";
2508 break;
2509 case 0x41: /* Analog Devices */
2510 name = lm90_detect_analog(client, common_address, chip_id, config1,
2511 convrate);
2512 break;
2513 case 0x47: /* GMT */
2514 name = lm90_detect_gmt(client, chip_id, config1, convrate);
2515 break;
2516 case 0x49: /* TI */
2517 name = lm90_detect_ti49(client, common_address, chip_id, config1, convrate);
2518 break;
2519 case 0x4d: /* Maxim Integrated */
2520 name = lm90_detect_maxim(client, common_address, chip_id,
2521 config1, convrate);
2522 break;
2523 case 0x54: /* ON MC1066, Microchip TC1068, TCM1617 (originally TelCom) */
2524 if (common_address && !(config1 & 0x3f) && !(convrate & 0xf8))
2525 name = "mc1066";
2526 break;
2527 case 0x55: /* TI */
2528 name = lm90_detect_ti(client, chip_id, config1, convrate);
2529 break;
2530 case 0x5c: /* Winbond/Nuvoton */
2531 name = lm90_detect_nuvoton(client, chip_id, config1, convrate);
2532 break;
2533 case 0xa1: /* NXP Semiconductor/Philips */
2534 name = lm90_detect_nxp(client, common_address, chip_id, config1, convrate);
2535 break;
2536 case 0xff: /* MAX1617, G767, NE1617 */
2537 if (common_address && chip_id == 0xff && convrate < 8)
2538 name = lm90_detect_max1617(client, config1);
2539 break;
2540 default:
2541 break;
2542 }
2543
2544 if (!name) { /* identification failed */
2545 dev_dbg(&adapter->dev,
2546 "Unsupported chip at 0x%02x (man_id=0x%02X, chip_id=0x%02X)\n",
2547 client->addr, man_id, chip_id);
2548 return -ENODEV;
2549 }
2550
2551 strscpy(info->type, name, I2C_NAME_SIZE);
2552
2553 return 0;
2554}
2555
2556static void lm90_restore_conf(void *_data)
2557{
2558 struct lm90_data *data = _data;
2559 struct i2c_client *client = data->client;
2560
2561 cancel_delayed_work_sync(&data->alert_work);
2562 cancel_work_sync(&data->report_work);
2563
2564 /* Restore initial configuration */
2565 if (data->flags & LM90_HAVE_CONVRATE)
2566 lm90_write_convrate(data, data->convrate_orig);
2567 lm90_write_reg(client, LM90_REG_CONFIG1, data->config_orig);
2568}
2569
2570static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
2571{
2572 struct device_node *np = client->dev.of_node;
2573 int config, convrate;
2574
2575 if (data->flags & LM90_HAVE_CONVRATE) {
2576 convrate = lm90_read_reg(client, LM90_REG_CONVRATE);
2577 if (convrate < 0)
2578 return convrate;
2579 data->convrate_orig = convrate;
2580 lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
2581 } else {
2582 data->update_interval = 500;
2583 }
2584
2585 /*
2586 * Start the conversions.
2587 */
2588 config = lm90_read_reg(client, LM90_REG_CONFIG1);
2589 if (config < 0)
2590 return config;
2591 data->config_orig = config;
2592 data->config = config;
2593
2594 /* Check Temperature Range Select */
2595 if (data->flags & LM90_HAVE_EXTENDED_TEMP) {
2596 if (of_property_read_bool(np, "ti,extended-range-enable"))
2597 config |= 0x04;
2598 if (!(config & 0x04))
2599 data->flags &= ~LM90_HAVE_EXTENDED_TEMP;
2600 }
2601
2602 /*
2603 * Put MAX6680/MAX8881 into extended resolution (bit 0x10,
2604 * 0.125 degree resolution) and range (0x08, extend range
2605 * to -64 degree) mode for the remote temperature sensor.
2606 * Note that expeciments with an actual chip do not show a difference
2607 * if bit 3 is set or not.
2608 */
2609 if (data->kind == max6680)
2610 config |= 0x18;
2611
2612 /*
2613 * Put MAX6654 into extended range (0x20, extend minimum range from
2614 * 0 degrees to -64 degrees). Note that extended resolution is not
2615 * possible on the MAX6654 unless conversion rate is set to 1 Hz or
2616 * slower, which is intentionally not done by default.
2617 */
2618 if (data->kind == max6654)
2619 config |= 0x20;
2620
2621 /*
2622 * Select external channel 0 for devices with three sensors
2623 */
2624 if (data->flags & LM90_HAVE_TEMP3)
2625 config &= ~0x08;
2626
2627 /*
2628 * Interrupt is enabled by default on reset, but it may be disabled
2629 * by bootloader, unmask it.
2630 */
2631 if (client->irq)
2632 config &= ~0x80;
2633
2634 config &= 0xBF; /* run */
2635 lm90_update_confreg(data, config);
2636
2637 return devm_add_action_or_reset(&client->dev, lm90_restore_conf, data);
2638}
2639
2640static bool lm90_is_tripped(struct i2c_client *client)
2641{
2642 struct lm90_data *data = i2c_get_clientdata(client);
2643 int ret;
2644
2645 ret = lm90_update_alarms(data, true);
2646 if (ret < 0)
2647 return false;
2648
2649 return !!data->current_alarms;
2650}
2651
2652static irqreturn_t lm90_irq_thread(int irq, void *dev_id)
2653{
2654 struct i2c_client *client = dev_id;
2655
2656 if (lm90_is_tripped(client))
2657 return IRQ_HANDLED;
2658 else
2659 return IRQ_NONE;
2660}
2661
2662static void lm90_remove_pec(void *dev)
2663{
2664 device_remove_file(dev, &dev_attr_pec);
2665}
2666
2667static int lm90_probe_channel_from_dt(struct i2c_client *client,
2668 struct device_node *child,
2669 struct lm90_data *data)
2670{
2671 u32 id;
2672 s32 val;
2673 int err;
2674 struct device *dev = &client->dev;
2675
2676 err = of_property_read_u32(child, "reg", &id);
2677 if (err) {
2678 dev_err(dev, "missing reg property of %pOFn\n", child);
2679 return err;
2680 }
2681
2682 if (id >= MAX_CHANNELS) {
2683 dev_err(dev, "invalid reg property value %d in %pOFn\n", id, child);
2684 return -EINVAL;
2685 }
2686
2687 err = of_property_read_string(child, "label", &data->channel_label[id]);
2688 if (err == -ENODATA || err == -EILSEQ) {
2689 dev_err(dev, "invalid label property in %pOFn\n", child);
2690 return err;
2691 }
2692
2693 if (data->channel_label[id])
2694 data->channel_config[id] |= HWMON_T_LABEL;
2695
2696 err = of_property_read_s32(child, "temperature-offset-millicelsius", &val);
2697 if (!err) {
2698 if (id == 0) {
2699 dev_err(dev, "temperature-offset-millicelsius can't be set for internal channel\n");
2700 return -EINVAL;
2701 }
2702
2703 err = lm90_set_temp_offset(data, lm90_temp_offset_index[id], id, val);
2704 if (err) {
2705 dev_err(dev, "can't set temperature offset %d for channel %d (%d)\n",
2706 val, id, err);
2707 return err;
2708 }
2709 }
2710
2711 return 0;
2712}
2713
2714static int lm90_parse_dt_channel_info(struct i2c_client *client,
2715 struct lm90_data *data)
2716{
2717 int err;
2718 struct device_node *child;
2719 struct device *dev = &client->dev;
2720 const struct device_node *np = dev->of_node;
2721
2722 for_each_child_of_node(np, child) {
2723 if (strcmp(child->name, "channel"))
2724 continue;
2725
2726 err = lm90_probe_channel_from_dt(client, child, data);
2727 if (err) {
2728 of_node_put(child);
2729 return err;
2730 }
2731 }
2732
2733 return 0;
2734}
2735
2736static const struct hwmon_ops lm90_ops = {
2737 .is_visible = lm90_is_visible,
2738 .read = lm90_read,
2739 .read_string = lm90_read_string,
2740 .write = lm90_write,
2741};
2742
2743static int lm90_probe(struct i2c_client *client)
2744{
2745 struct device *dev = &client->dev;
2746 struct i2c_adapter *adapter = client->adapter;
2747 struct hwmon_channel_info *info;
2748 struct device *hwmon_dev;
2749 struct lm90_data *data;
2750 int err;
2751
2752 err = devm_regulator_get_enable(dev, "vcc");
2753 if (err)
2754 return dev_err_probe(dev, err, "Failed to enable regulator\n");
2755
2756 data = devm_kzalloc(dev, sizeof(struct lm90_data), GFP_KERNEL);
2757 if (!data)
2758 return -ENOMEM;
2759
2760 data->client = client;
2761 i2c_set_clientdata(client, data);
2762 mutex_init(&data->update_lock);
2763 INIT_DELAYED_WORK(&data->alert_work, lm90_alert_work);
2764 INIT_WORK(&data->report_work, lm90_report_alarms);
2765
2766 /* Set the device type */
2767 if (client->dev.of_node)
2768 data->kind = (uintptr_t)of_device_get_match_data(&client->dev);
2769 else
2770 data->kind = i2c_match_id(lm90_id, client)->driver_data;
2771
2772 /*
2773 * Different devices have different alarm bits triggering the
2774 * ALERT# output
2775 */
2776 data->alert_alarms = lm90_params[data->kind].alert_alarms;
2777 data->resolution = lm90_params[data->kind].resolution ? : 11;
2778
2779 /* Set chip capabilities */
2780 data->flags = lm90_params[data->kind].flags;
2781
2782 if ((data->flags & (LM90_HAVE_PEC | LM90_HAVE_PARTIAL_PEC)) &&
2783 !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_PEC))
2784 data->flags &= ~(LM90_HAVE_PEC | LM90_HAVE_PARTIAL_PEC);
2785
2786 if ((data->flags & LM90_HAVE_PARTIAL_PEC) &&
2787 !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
2788 data->flags &= ~LM90_HAVE_PARTIAL_PEC;
2789
2790 data->chip.ops = &lm90_ops;
2791 data->chip.info = data->info;
2792
2793 data->info[0] = &data->chip_info;
2794 info = &data->chip_info;
2795 info->type = hwmon_chip;
2796 info->config = data->chip_config;
2797
2798 data->chip_config[0] = HWMON_C_REGISTER_TZ;
2799 if (data->flags & LM90_HAVE_ALARMS)
2800 data->chip_config[0] |= HWMON_C_ALARMS;
2801 if (data->flags & LM90_HAVE_CONVRATE)
2802 data->chip_config[0] |= HWMON_C_UPDATE_INTERVAL;
2803 if (data->flags & LM90_HAVE_FAULTQUEUE)
2804 data->chip_config[0] |= HWMON_C_TEMP_SAMPLES;
2805 data->info[1] = &data->temp_info;
2806
2807 info = &data->temp_info;
2808 info->type = hwmon_temp;
2809 info->config = data->channel_config;
2810
2811 data->channel_config[0] = HWMON_T_INPUT | HWMON_T_MAX |
2812 HWMON_T_MAX_ALARM;
2813 data->channel_config[1] = HWMON_T_INPUT | HWMON_T_MAX |
2814 HWMON_T_MAX_ALARM | HWMON_T_FAULT;
2815
2816 if (data->flags & LM90_HAVE_LOW) {
2817 data->channel_config[0] |= HWMON_T_MIN | HWMON_T_MIN_ALARM;
2818 data->channel_config[1] |= HWMON_T_MIN | HWMON_T_MIN_ALARM;
2819 }
2820
2821 if (data->flags & LM90_HAVE_CRIT) {
2822 data->channel_config[0] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
2823 data->channel_config[1] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
2824 }
2825
2826 if (data->flags & LM90_HAVE_OFFSET)
2827 data->channel_config[1] |= HWMON_T_OFFSET;
2828
2829 if (data->flags & LM90_HAVE_EMERGENCY) {
2830 data->channel_config[0] |= HWMON_T_EMERGENCY |
2831 HWMON_T_EMERGENCY_HYST;
2832 data->channel_config[1] |= HWMON_T_EMERGENCY |
2833 HWMON_T_EMERGENCY_HYST;
2834 }
2835
2836 if (data->flags & LM90_HAVE_EMERGENCY_ALARM) {
2837 data->channel_config[0] |= HWMON_T_EMERGENCY_ALARM;
2838 data->channel_config[1] |= HWMON_T_EMERGENCY_ALARM;
2839 }
2840
2841 if (data->flags & LM90_HAVE_TEMP3) {
2842 data->channel_config[2] = HWMON_T_INPUT |
2843 HWMON_T_MIN | HWMON_T_MAX |
2844 HWMON_T_CRIT | HWMON_T_CRIT_HYST |
2845 HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM |
2846 HWMON_T_CRIT_ALARM | HWMON_T_FAULT;
2847 if (data->flags & LM90_HAVE_EMERGENCY) {
2848 data->channel_config[2] |= HWMON_T_EMERGENCY |
2849 HWMON_T_EMERGENCY_HYST;
2850 }
2851 if (data->flags & LM90_HAVE_EMERGENCY_ALARM)
2852 data->channel_config[2] |= HWMON_T_EMERGENCY_ALARM;
2853 if (data->flags & LM90_HAVE_OFFSET)
2854 data->channel_config[2] |= HWMON_T_OFFSET;
2855 }
2856
2857 data->faultqueue_mask = lm90_params[data->kind].faultqueue_mask;
2858 data->faultqueue_depth = lm90_params[data->kind].faultqueue_depth;
2859 data->reg_local_ext = lm90_params[data->kind].reg_local_ext;
2860 if (data->flags & LM90_HAVE_REMOTE_EXT)
2861 data->reg_remote_ext = LM90_REG_REMOTE_TEMPL;
2862 data->reg_status2 = lm90_params[data->kind].reg_status2;
2863
2864 /* Set maximum conversion rate */
2865 data->max_convrate = lm90_params[data->kind].max_convrate;
2866
2867 /* Parse device-tree channel information */
2868 if (client->dev.of_node) {
2869 err = lm90_parse_dt_channel_info(client, data);
2870 if (err)
2871 return err;
2872 }
2873
2874 /* Initialize the LM90 chip */
2875 err = lm90_init_client(client, data);
2876 if (err < 0) {
2877 dev_err(dev, "Failed to initialize device\n");
2878 return err;
2879 }
2880
2881 /*
2882 * The 'pec' attribute is attached to the i2c device and thus created
2883 * separately.
2884 */
2885 if (data->flags & (LM90_HAVE_PEC | LM90_HAVE_PARTIAL_PEC)) {
2886 err = device_create_file(dev, &dev_attr_pec);
2887 if (err)
2888 return err;
2889 err = devm_add_action_or_reset(dev, lm90_remove_pec, dev);
2890 if (err)
2891 return err;
2892 }
2893
2894 hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
2895 data, &data->chip,
2896 NULL);
2897 if (IS_ERR(hwmon_dev))
2898 return PTR_ERR(hwmon_dev);
2899
2900 data->hwmon_dev = hwmon_dev;
2901
2902 if (client->irq) {
2903 dev_dbg(dev, "IRQ: %d\n", client->irq);
2904 err = devm_request_threaded_irq(dev, client->irq,
2905 NULL, lm90_irq_thread,
2906 IRQF_ONESHOT, "lm90", client);
2907 if (err < 0) {
2908 dev_err(dev, "cannot request IRQ %d\n", client->irq);
2909 return err;
2910 }
2911 }
2912
2913 return 0;
2914}
2915
2916static void lm90_alert(struct i2c_client *client, enum i2c_alert_protocol type,
2917 unsigned int flag)
2918{
2919 if (type != I2C_PROTOCOL_SMBUS_ALERT)
2920 return;
2921
2922 if (lm90_is_tripped(client)) {
2923 /*
2924 * Disable ALERT# output, because these chips don't implement
2925 * SMBus alert correctly; they should only hold the alert line
2926 * low briefly.
2927 */
2928 struct lm90_data *data = i2c_get_clientdata(client);
2929
2930 if ((data->flags & LM90_HAVE_BROKEN_ALERT) &&
2931 (data->current_alarms & data->alert_alarms)) {
2932 if (!(data->config & 0x80)) {
2933 dev_dbg(&client->dev, "Disabling ALERT#\n");
2934 lm90_update_confreg(data, data->config | 0x80);
2935 }
2936 schedule_delayed_work(&data->alert_work,
2937 max_t(int, HZ, msecs_to_jiffies(data->update_interval)));
2938 }
2939 } else {
2940 dev_dbg(&client->dev, "Everything OK\n");
2941 }
2942}
2943
2944static int lm90_suspend(struct device *dev)
2945{
2946 struct lm90_data *data = dev_get_drvdata(dev);
2947 struct i2c_client *client = data->client;
2948
2949 if (client->irq)
2950 disable_irq(client->irq);
2951
2952 return 0;
2953}
2954
2955static int lm90_resume(struct device *dev)
2956{
2957 struct lm90_data *data = dev_get_drvdata(dev);
2958 struct i2c_client *client = data->client;
2959
2960 if (client->irq)
2961 enable_irq(client->irq);
2962
2963 return 0;
2964}
2965
2966static DEFINE_SIMPLE_DEV_PM_OPS(lm90_pm_ops, lm90_suspend, lm90_resume);
2967
2968static struct i2c_driver lm90_driver = {
2969 .class = I2C_CLASS_HWMON,
2970 .driver = {
2971 .name = "lm90",
2972 .of_match_table = of_match_ptr(lm90_of_match),
2973 .pm = pm_sleep_ptr(&lm90_pm_ops),
2974 },
2975 .probe = lm90_probe,
2976 .alert = lm90_alert,
2977 .id_table = lm90_id,
2978 .detect = lm90_detect,
2979 .address_list = normal_i2c,
2980};
2981
2982module_i2c_driver(lm90_driver);
2983
2984MODULE_AUTHOR("Jean Delvare <jdelvare@suse.de>");
2985MODULE_DESCRIPTION("LM90/ADM1032 driver");
2986MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * lm90.c - Part of lm_sensors, Linux kernel modules for hardware
4 * monitoring
5 * Copyright (C) 2003-2010 Jean Delvare <jdelvare@suse.de>
6 *
7 * Based on the lm83 driver. The LM90 is a sensor chip made by National
8 * Semiconductor. It reports up to two temperatures (its own plus up to
9 * one external one) with a 0.125 deg resolution (1 deg for local
10 * temperature) and a 3-4 deg accuracy.
11 *
12 * This driver also supports the LM89 and LM99, two other sensor chips
13 * made by National Semiconductor. Both have an increased remote
14 * temperature measurement accuracy (1 degree), and the LM99
15 * additionally shifts remote temperatures (measured and limits) by 16
16 * degrees, which allows for higher temperatures measurement.
17 * Note that there is no way to differentiate between both chips.
18 * When device is auto-detected, the driver will assume an LM99.
19 *
20 * This driver also supports the LM86, another sensor chip made by
21 * National Semiconductor. It is exactly similar to the LM90 except it
22 * has a higher accuracy.
23 *
24 * This driver also supports the ADM1032, a sensor chip made by Analog
25 * Devices. That chip is similar to the LM90, with a few differences
26 * that are not handled by this driver. Among others, it has a higher
27 * accuracy than the LM90, much like the LM86 does.
28 *
29 * This driver also supports the MAX6657, MAX6658 and MAX6659 sensor
30 * chips made by Maxim. These chips are similar to the LM86.
31 * Note that there is no easy way to differentiate between the three
32 * variants. We use the device address to detect MAX6659, which will result
33 * in a detection as max6657 if it is on address 0x4c. The extra address
34 * and features of the MAX6659 are only supported if the chip is configured
35 * explicitly as max6659, or if its address is not 0x4c.
36 * These chips lack the remote temperature offset feature.
37 *
38 * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
39 * MAX6692 chips made by Maxim. These are again similar to the LM86,
40 * but they use unsigned temperature values and can report temperatures
41 * from 0 to 145 degrees.
42 *
43 * This driver also supports the MAX6680 and MAX6681, two other sensor
44 * chips made by Maxim. These are quite similar to the other Maxim
45 * chips. The MAX6680 and MAX6681 only differ in the pinout so they can
46 * be treated identically.
47 *
48 * This driver also supports the MAX6695 and MAX6696, two other sensor
49 * chips made by Maxim. These are also quite similar to other Maxim
50 * chips, but support three temperature sensors instead of two. MAX6695
51 * and MAX6696 only differ in the pinout so they can be treated identically.
52 *
53 * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as
54 * NCT1008 from ON Semiconductor. The chips are supported in both compatibility
55 * and extended mode. They are mostly compatible with LM90 except for a data
56 * format difference for the temperature value registers.
57 *
58 * This driver also supports the SA56004 from Philips. This device is
59 * pin-compatible with the LM86, the ED/EDP parts are also address-compatible.
60 *
61 * This driver also supports the G781 from GMT. This device is compatible
62 * with the ADM1032.
63 *
64 * This driver also supports TMP451 from Texas Instruments. This device is
65 * supported in both compatibility and extended mode. It's mostly compatible
66 * with ADT7461 except for local temperature low byte register and max
67 * conversion rate.
68 *
69 * Since the LM90 was the first chipset supported by this driver, most
70 * comments will refer to this chipset, but are actually general and
71 * concern all supported chipsets, unless mentioned otherwise.
72 */
73
74#include <linux/module.h>
75#include <linux/init.h>
76#include <linux/slab.h>
77#include <linux/jiffies.h>
78#include <linux/i2c.h>
79#include <linux/hwmon.h>
80#include <linux/err.h>
81#include <linux/mutex.h>
82#include <linux/of_device.h>
83#include <linux/sysfs.h>
84#include <linux/interrupt.h>
85#include <linux/regulator/consumer.h>
86
87/*
88 * Addresses to scan
89 * Address is fully defined internally and cannot be changed except for
90 * MAX6659, MAX6680 and MAX6681.
91 * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649,
92 * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c.
93 * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D
94 * have address 0x4d.
95 * MAX6647 has address 0x4e.
96 * MAX6659 can have address 0x4c, 0x4d or 0x4e.
97 * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
98 * 0x4c, 0x4d or 0x4e.
99 * SA56004 can have address 0x48 through 0x4F.
100 */
101
102static const unsigned short normal_i2c[] = {
103 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x48, 0x49, 0x4a, 0x4b, 0x4c,
104 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
105
106enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
107 max6646, w83l771, max6696, sa56004, g781, tmp451 };
108
109/*
110 * The LM90 registers
111 */
112
113#define LM90_REG_R_MAN_ID 0xFE
114#define LM90_REG_R_CHIP_ID 0xFF
115#define LM90_REG_R_CONFIG1 0x03
116#define LM90_REG_W_CONFIG1 0x09
117#define LM90_REG_R_CONFIG2 0xBF
118#define LM90_REG_W_CONFIG2 0xBF
119#define LM90_REG_R_CONVRATE 0x04
120#define LM90_REG_W_CONVRATE 0x0A
121#define LM90_REG_R_STATUS 0x02
122#define LM90_REG_R_LOCAL_TEMP 0x00
123#define LM90_REG_R_LOCAL_HIGH 0x05
124#define LM90_REG_W_LOCAL_HIGH 0x0B
125#define LM90_REG_R_LOCAL_LOW 0x06
126#define LM90_REG_W_LOCAL_LOW 0x0C
127#define LM90_REG_R_LOCAL_CRIT 0x20
128#define LM90_REG_W_LOCAL_CRIT 0x20
129#define LM90_REG_R_REMOTE_TEMPH 0x01
130#define LM90_REG_R_REMOTE_TEMPL 0x10
131#define LM90_REG_R_REMOTE_OFFSH 0x11
132#define LM90_REG_W_REMOTE_OFFSH 0x11
133#define LM90_REG_R_REMOTE_OFFSL 0x12
134#define LM90_REG_W_REMOTE_OFFSL 0x12
135#define LM90_REG_R_REMOTE_HIGHH 0x07
136#define LM90_REG_W_REMOTE_HIGHH 0x0D
137#define LM90_REG_R_REMOTE_HIGHL 0x13
138#define LM90_REG_W_REMOTE_HIGHL 0x13
139#define LM90_REG_R_REMOTE_LOWH 0x08
140#define LM90_REG_W_REMOTE_LOWH 0x0E
141#define LM90_REG_R_REMOTE_LOWL 0x14
142#define LM90_REG_W_REMOTE_LOWL 0x14
143#define LM90_REG_R_REMOTE_CRIT 0x19
144#define LM90_REG_W_REMOTE_CRIT 0x19
145#define LM90_REG_R_TCRIT_HYST 0x21
146#define LM90_REG_W_TCRIT_HYST 0x21
147
148/* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */
149
150#define MAX6657_REG_R_LOCAL_TEMPL 0x11
151#define MAX6696_REG_R_STATUS2 0x12
152#define MAX6659_REG_R_REMOTE_EMERG 0x16
153#define MAX6659_REG_W_REMOTE_EMERG 0x16
154#define MAX6659_REG_R_LOCAL_EMERG 0x17
155#define MAX6659_REG_W_LOCAL_EMERG 0x17
156
157/* SA56004 registers */
158
159#define SA56004_REG_R_LOCAL_TEMPL 0x22
160
161#define LM90_MAX_CONVRATE_MS 16000 /* Maximum conversion rate in ms */
162
163/* TMP451 registers */
164#define TMP451_REG_R_LOCAL_TEMPL 0x15
165
166/*
167 * Device flags
168 */
169#define LM90_FLAG_ADT7461_EXT (1 << 0) /* ADT7461 extended mode */
170/* Device features */
171#define LM90_HAVE_OFFSET (1 << 1) /* temperature offset register */
172#define LM90_HAVE_REM_LIMIT_EXT (1 << 3) /* extended remote limit */
173#define LM90_HAVE_EMERGENCY (1 << 4) /* 3rd upper (emergency) limit */
174#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */
175#define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */
176#define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
177#define LM90_PAUSE_FOR_CONFIG (1 << 8) /* Pause conversion for config */
178
179/* LM90 status */
180#define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
181#define LM90_STATUS_RTHRM (1 << 1) /* remote THERM limit tripped */
182#define LM90_STATUS_ROPEN (1 << 2) /* remote is an open circuit */
183#define LM90_STATUS_RLOW (1 << 3) /* remote low temp limit tripped */
184#define LM90_STATUS_RHIGH (1 << 4) /* remote high temp limit tripped */
185#define LM90_STATUS_LLOW (1 << 5) /* local low temp limit tripped */
186#define LM90_STATUS_LHIGH (1 << 6) /* local high temp limit tripped */
187
188#define MAX6696_STATUS2_R2THRM (1 << 1) /* remote2 THERM limit tripped */
189#define MAX6696_STATUS2_R2OPEN (1 << 2) /* remote2 is an open circuit */
190#define MAX6696_STATUS2_R2LOW (1 << 3) /* remote2 low temp limit tripped */
191#define MAX6696_STATUS2_R2HIGH (1 << 4) /* remote2 high temp limit tripped */
192#define MAX6696_STATUS2_ROT2 (1 << 5) /* remote emergency limit tripped */
193#define MAX6696_STATUS2_R2OT2 (1 << 6) /* remote2 emergency limit tripped */
194#define MAX6696_STATUS2_LOT2 (1 << 7) /* local emergency limit tripped */
195
196/*
197 * Driver data (common to all clients)
198 */
199
200static const struct i2c_device_id lm90_id[] = {
201 { "adm1032", adm1032 },
202 { "adt7461", adt7461 },
203 { "adt7461a", adt7461 },
204 { "g781", g781 },
205 { "lm90", lm90 },
206 { "lm86", lm86 },
207 { "lm89", lm86 },
208 { "lm99", lm99 },
209 { "max6646", max6646 },
210 { "max6647", max6646 },
211 { "max6649", max6646 },
212 { "max6657", max6657 },
213 { "max6658", max6657 },
214 { "max6659", max6659 },
215 { "max6680", max6680 },
216 { "max6681", max6680 },
217 { "max6695", max6696 },
218 { "max6696", max6696 },
219 { "nct1008", adt7461 },
220 { "w83l771", w83l771 },
221 { "sa56004", sa56004 },
222 { "tmp451", tmp451 },
223 { }
224};
225MODULE_DEVICE_TABLE(i2c, lm90_id);
226
227static const struct of_device_id __maybe_unused lm90_of_match[] = {
228 {
229 .compatible = "adi,adm1032",
230 .data = (void *)adm1032
231 },
232 {
233 .compatible = "adi,adt7461",
234 .data = (void *)adt7461
235 },
236 {
237 .compatible = "adi,adt7461a",
238 .data = (void *)adt7461
239 },
240 {
241 .compatible = "gmt,g781",
242 .data = (void *)g781
243 },
244 {
245 .compatible = "national,lm90",
246 .data = (void *)lm90
247 },
248 {
249 .compatible = "national,lm86",
250 .data = (void *)lm86
251 },
252 {
253 .compatible = "national,lm89",
254 .data = (void *)lm86
255 },
256 {
257 .compatible = "national,lm99",
258 .data = (void *)lm99
259 },
260 {
261 .compatible = "dallas,max6646",
262 .data = (void *)max6646
263 },
264 {
265 .compatible = "dallas,max6647",
266 .data = (void *)max6646
267 },
268 {
269 .compatible = "dallas,max6649",
270 .data = (void *)max6646
271 },
272 {
273 .compatible = "dallas,max6657",
274 .data = (void *)max6657
275 },
276 {
277 .compatible = "dallas,max6658",
278 .data = (void *)max6657
279 },
280 {
281 .compatible = "dallas,max6659",
282 .data = (void *)max6659
283 },
284 {
285 .compatible = "dallas,max6680",
286 .data = (void *)max6680
287 },
288 {
289 .compatible = "dallas,max6681",
290 .data = (void *)max6680
291 },
292 {
293 .compatible = "dallas,max6695",
294 .data = (void *)max6696
295 },
296 {
297 .compatible = "dallas,max6696",
298 .data = (void *)max6696
299 },
300 {
301 .compatible = "onnn,nct1008",
302 .data = (void *)adt7461
303 },
304 {
305 .compatible = "winbond,w83l771",
306 .data = (void *)w83l771
307 },
308 {
309 .compatible = "nxp,sa56004",
310 .data = (void *)sa56004
311 },
312 {
313 .compatible = "ti,tmp451",
314 .data = (void *)tmp451
315 },
316 { },
317};
318MODULE_DEVICE_TABLE(of, lm90_of_match);
319
320/*
321 * chip type specific parameters
322 */
323struct lm90_params {
324 u32 flags; /* Capabilities */
325 u16 alert_alarms; /* Which alarm bits trigger ALERT# */
326 /* Upper 8 bits for max6695/96 */
327 u8 max_convrate; /* Maximum conversion rate register value */
328 u8 reg_local_ext; /* Extended local temp register (optional) */
329};
330
331static const struct lm90_params lm90_params[] = {
332 [adm1032] = {
333 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
334 | LM90_HAVE_BROKEN_ALERT,
335 .alert_alarms = 0x7c,
336 .max_convrate = 10,
337 },
338 [adt7461] = {
339 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
340 | LM90_HAVE_BROKEN_ALERT,
341 .alert_alarms = 0x7c,
342 .max_convrate = 10,
343 },
344 [g781] = {
345 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
346 | LM90_HAVE_BROKEN_ALERT,
347 .alert_alarms = 0x7c,
348 .max_convrate = 8,
349 },
350 [lm86] = {
351 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
352 .alert_alarms = 0x7b,
353 .max_convrate = 9,
354 },
355 [lm90] = {
356 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
357 .alert_alarms = 0x7b,
358 .max_convrate = 9,
359 },
360 [lm99] = {
361 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
362 .alert_alarms = 0x7b,
363 .max_convrate = 9,
364 },
365 [max6646] = {
366 .alert_alarms = 0x7c,
367 .max_convrate = 6,
368 .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
369 },
370 [max6657] = {
371 .flags = LM90_PAUSE_FOR_CONFIG,
372 .alert_alarms = 0x7c,
373 .max_convrate = 8,
374 .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
375 },
376 [max6659] = {
377 .flags = LM90_HAVE_EMERGENCY,
378 .alert_alarms = 0x7c,
379 .max_convrate = 8,
380 .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
381 },
382 [max6680] = {
383 .flags = LM90_HAVE_OFFSET,
384 .alert_alarms = 0x7c,
385 .max_convrate = 7,
386 },
387 [max6696] = {
388 .flags = LM90_HAVE_EMERGENCY
389 | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3,
390 .alert_alarms = 0x1c7c,
391 .max_convrate = 6,
392 .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
393 },
394 [w83l771] = {
395 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
396 .alert_alarms = 0x7c,
397 .max_convrate = 8,
398 },
399 [sa56004] = {
400 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
401 .alert_alarms = 0x7b,
402 .max_convrate = 9,
403 .reg_local_ext = SA56004_REG_R_LOCAL_TEMPL,
404 },
405 [tmp451] = {
406 .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
407 | LM90_HAVE_BROKEN_ALERT,
408 .alert_alarms = 0x7c,
409 .max_convrate = 9,
410 .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
411 },
412};
413
414/*
415 * TEMP8 register index
416 */
417enum lm90_temp8_reg_index {
418 LOCAL_LOW = 0,
419 LOCAL_HIGH,
420 LOCAL_CRIT,
421 REMOTE_CRIT,
422 LOCAL_EMERG, /* max6659 and max6695/96 */
423 REMOTE_EMERG, /* max6659 and max6695/96 */
424 REMOTE2_CRIT, /* max6695/96 only */
425 REMOTE2_EMERG, /* max6695/96 only */
426 TEMP8_REG_NUM
427};
428
429/*
430 * TEMP11 register index
431 */
432enum lm90_temp11_reg_index {
433 REMOTE_TEMP = 0,
434 REMOTE_LOW,
435 REMOTE_HIGH,
436 REMOTE_OFFSET, /* except max6646, max6657/58/59, and max6695/96 */
437 LOCAL_TEMP,
438 REMOTE2_TEMP, /* max6695/96 only */
439 REMOTE2_LOW, /* max6695/96 only */
440 REMOTE2_HIGH, /* max6695/96 only */
441 TEMP11_REG_NUM
442};
443
444/*
445 * Client data (each client gets its own)
446 */
447
448struct lm90_data {
449 struct i2c_client *client;
450 u32 channel_config[4];
451 struct hwmon_channel_info temp_info;
452 const struct hwmon_channel_info *info[3];
453 struct hwmon_chip_info chip;
454 struct mutex update_lock;
455 bool valid; /* true if register values are valid */
456 unsigned long last_updated; /* in jiffies */
457 int kind;
458 u32 flags;
459
460 unsigned int update_interval; /* in milliseconds */
461
462 u8 config; /* Current configuration register value */
463 u8 config_orig; /* Original configuration register value */
464 u8 convrate_orig; /* Original conversion rate register value */
465 u16 alert_alarms; /* Which alarm bits trigger ALERT# */
466 /* Upper 8 bits for max6695/96 */
467 u8 max_convrate; /* Maximum conversion rate */
468 u8 reg_local_ext; /* local extension register offset */
469
470 /* registers values */
471 s8 temp8[TEMP8_REG_NUM];
472 s16 temp11[TEMP11_REG_NUM];
473 u8 temp_hyst;
474 u16 alarms; /* bitvector (upper 8 bits for max6695/96) */
475};
476
477/*
478 * Support functions
479 */
480
481/*
482 * The ADM1032 supports PEC but not on write byte transactions, so we need
483 * to explicitly ask for a transaction without PEC.
484 */
485static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value)
486{
487 return i2c_smbus_xfer(client->adapter, client->addr,
488 client->flags & ~I2C_CLIENT_PEC,
489 I2C_SMBUS_WRITE, value, I2C_SMBUS_BYTE, NULL);
490}
491
492/*
493 * It is assumed that client->update_lock is held (unless we are in
494 * detection or initialization steps). This matters when PEC is enabled,
495 * because we don't want the address pointer to change between the write
496 * byte and the read byte transactions.
497 */
498static int lm90_read_reg(struct i2c_client *client, u8 reg)
499{
500 int err;
501
502 if (client->flags & I2C_CLIENT_PEC) {
503 err = adm1032_write_byte(client, reg);
504 if (err >= 0)
505 err = i2c_smbus_read_byte(client);
506 } else
507 err = i2c_smbus_read_byte_data(client, reg);
508
509 return err;
510}
511
512static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl)
513{
514 int oldh, newh, l;
515
516 /*
517 * There is a trick here. We have to read two registers to have the
518 * sensor temperature, but we have to beware a conversion could occur
519 * between the readings. The datasheet says we should either use
520 * the one-shot conversion register, which we don't want to do
521 * (disables hardware monitoring) or monitor the busy bit, which is
522 * impossible (we can't read the values and monitor that bit at the
523 * exact same time). So the solution used here is to read the high
524 * byte once, then the low byte, then the high byte again. If the new
525 * high byte matches the old one, then we have a valid reading. Else
526 * we have to read the low byte again, and now we believe we have a
527 * correct reading.
528 */
529 oldh = lm90_read_reg(client, regh);
530 if (oldh < 0)
531 return oldh;
532 l = lm90_read_reg(client, regl);
533 if (l < 0)
534 return l;
535 newh = lm90_read_reg(client, regh);
536 if (newh < 0)
537 return newh;
538 if (oldh != newh) {
539 l = lm90_read_reg(client, regl);
540 if (l < 0)
541 return l;
542 }
543 return (newh << 8) | l;
544}
545
546static int lm90_update_confreg(struct lm90_data *data, u8 config)
547{
548 if (data->config != config) {
549 int err;
550
551 err = i2c_smbus_write_byte_data(data->client,
552 LM90_REG_W_CONFIG1,
553 config);
554 if (err)
555 return err;
556 data->config = config;
557 }
558 return 0;
559}
560
561/*
562 * client->update_lock must be held when calling this function (unless we are
563 * in detection or initialization steps), and while a remote channel other
564 * than channel 0 is selected. Also, calling code must make sure to re-select
565 * external channel 0 before releasing the lock. This is necessary because
566 * various registers have different meanings as a result of selecting a
567 * non-default remote channel.
568 */
569static int lm90_select_remote_channel(struct lm90_data *data, int channel)
570{
571 int err = 0;
572
573 if (data->kind == max6696) {
574 u8 config = data->config & ~0x08;
575
576 if (channel)
577 config |= 0x08;
578 err = lm90_update_confreg(data, config);
579 }
580 return err;
581}
582
583static int lm90_write_convrate(struct lm90_data *data, int val)
584{
585 u8 config = data->config;
586 int err;
587
588 /* Save config and pause conversion */
589 if (data->flags & LM90_PAUSE_FOR_CONFIG) {
590 err = lm90_update_confreg(data, config | 0x40);
591 if (err < 0)
592 return err;
593 }
594
595 /* Set conv rate */
596 err = i2c_smbus_write_byte_data(data->client, LM90_REG_W_CONVRATE, val);
597
598 /* Revert change to config */
599 lm90_update_confreg(data, config);
600
601 return err;
602}
603
604/*
605 * Set conversion rate.
606 * client->update_lock must be held when calling this function (unless we are
607 * in detection or initialization steps).
608 */
609static int lm90_set_convrate(struct i2c_client *client, struct lm90_data *data,
610 unsigned int interval)
611{
612 unsigned int update_interval;
613 int i, err;
614
615 /* Shift calculations to avoid rounding errors */
616 interval <<= 6;
617
618 /* find the nearest update rate */
619 for (i = 0, update_interval = LM90_MAX_CONVRATE_MS << 6;
620 i < data->max_convrate; i++, update_interval >>= 1)
621 if (interval >= update_interval * 3 / 4)
622 break;
623
624 err = lm90_write_convrate(data, i);
625 data->update_interval = DIV_ROUND_CLOSEST(update_interval, 64);
626 return err;
627}
628
629static int lm90_update_limits(struct device *dev)
630{
631 struct lm90_data *data = dev_get_drvdata(dev);
632 struct i2c_client *client = data->client;
633 int val;
634
635 val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
636 if (val < 0)
637 return val;
638 data->temp8[LOCAL_CRIT] = val;
639
640 val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
641 if (val < 0)
642 return val;
643 data->temp8[REMOTE_CRIT] = val;
644
645 val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
646 if (val < 0)
647 return val;
648 data->temp_hyst = val;
649
650 val = lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH);
651 if (val < 0)
652 return val;
653 data->temp11[REMOTE_LOW] = val << 8;
654
655 if (data->flags & LM90_HAVE_REM_LIMIT_EXT) {
656 val = lm90_read_reg(client, LM90_REG_R_REMOTE_LOWL);
657 if (val < 0)
658 return val;
659 data->temp11[REMOTE_LOW] |= val;
660 }
661
662 val = lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH);
663 if (val < 0)
664 return val;
665 data->temp11[REMOTE_HIGH] = val << 8;
666
667 if (data->flags & LM90_HAVE_REM_LIMIT_EXT) {
668 val = lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHL);
669 if (val < 0)
670 return val;
671 data->temp11[REMOTE_HIGH] |= val;
672 }
673
674 if (data->flags & LM90_HAVE_OFFSET) {
675 val = lm90_read16(client, LM90_REG_R_REMOTE_OFFSH,
676 LM90_REG_R_REMOTE_OFFSL);
677 if (val < 0)
678 return val;
679 data->temp11[REMOTE_OFFSET] = val;
680 }
681
682 if (data->flags & LM90_HAVE_EMERGENCY) {
683 val = lm90_read_reg(client, MAX6659_REG_R_LOCAL_EMERG);
684 if (val < 0)
685 return val;
686 data->temp8[LOCAL_EMERG] = val;
687
688 val = lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG);
689 if (val < 0)
690 return val;
691 data->temp8[REMOTE_EMERG] = val;
692 }
693
694 if (data->kind == max6696) {
695 val = lm90_select_remote_channel(data, 1);
696 if (val < 0)
697 return val;
698
699 val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
700 if (val < 0)
701 return val;
702 data->temp8[REMOTE2_CRIT] = val;
703
704 val = lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG);
705 if (val < 0)
706 return val;
707 data->temp8[REMOTE2_EMERG] = val;
708
709 val = lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH);
710 if (val < 0)
711 return val;
712 data->temp11[REMOTE2_LOW] = val << 8;
713
714 val = lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH);
715 if (val < 0)
716 return val;
717 data->temp11[REMOTE2_HIGH] = val << 8;
718
719 lm90_select_remote_channel(data, 0);
720 }
721
722 return 0;
723}
724
725static int lm90_update_device(struct device *dev)
726{
727 struct lm90_data *data = dev_get_drvdata(dev);
728 struct i2c_client *client = data->client;
729 unsigned long next_update;
730 int val;
731
732 if (!data->valid) {
733 val = lm90_update_limits(dev);
734 if (val < 0)
735 return val;
736 }
737
738 next_update = data->last_updated +
739 msecs_to_jiffies(data->update_interval);
740 if (time_after(jiffies, next_update) || !data->valid) {
741 dev_dbg(&client->dev, "Updating lm90 data.\n");
742
743 data->valid = false;
744
745 val = lm90_read_reg(client, LM90_REG_R_LOCAL_LOW);
746 if (val < 0)
747 return val;
748 data->temp8[LOCAL_LOW] = val;
749
750 val = lm90_read_reg(client, LM90_REG_R_LOCAL_HIGH);
751 if (val < 0)
752 return val;
753 data->temp8[LOCAL_HIGH] = val;
754
755 if (data->reg_local_ext) {
756 val = lm90_read16(client, LM90_REG_R_LOCAL_TEMP,
757 data->reg_local_ext);
758 if (val < 0)
759 return val;
760 data->temp11[LOCAL_TEMP] = val;
761 } else {
762 val = lm90_read_reg(client, LM90_REG_R_LOCAL_TEMP);
763 if (val < 0)
764 return val;
765 data->temp11[LOCAL_TEMP] = val << 8;
766 }
767 val = lm90_read16(client, LM90_REG_R_REMOTE_TEMPH,
768 LM90_REG_R_REMOTE_TEMPL);
769 if (val < 0)
770 return val;
771 data->temp11[REMOTE_TEMP] = val;
772
773 val = lm90_read_reg(client, LM90_REG_R_STATUS);
774 if (val < 0)
775 return val;
776 data->alarms = val; /* lower 8 bit of alarms */
777
778 if (data->kind == max6696) {
779 val = lm90_select_remote_channel(data, 1);
780 if (val < 0)
781 return val;
782
783 val = lm90_read16(client, LM90_REG_R_REMOTE_TEMPH,
784 LM90_REG_R_REMOTE_TEMPL);
785 if (val < 0) {
786 lm90_select_remote_channel(data, 0);
787 return val;
788 }
789 data->temp11[REMOTE2_TEMP] = val;
790
791 lm90_select_remote_channel(data, 0);
792
793 val = lm90_read_reg(client, MAX6696_REG_R_STATUS2);
794 if (val < 0)
795 return val;
796 data->alarms |= val << 8;
797 }
798
799 /*
800 * Re-enable ALERT# output if it was originally enabled and
801 * relevant alarms are all clear
802 */
803 if (!(data->config_orig & 0x80) &&
804 !(data->alarms & data->alert_alarms)) {
805 if (data->config & 0x80) {
806 dev_dbg(&client->dev, "Re-enabling ALERT#\n");
807 lm90_update_confreg(data, data->config & ~0x80);
808 }
809 }
810
811 data->last_updated = jiffies;
812 data->valid = true;
813 }
814
815 return 0;
816}
817
818/*
819 * Conversions
820 * For local temperatures and limits, critical limits and the hysteresis
821 * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celsius.
822 * For remote temperatures and limits, it uses signed 11-bit values with
823 * LSB = 0.125 degree Celsius, left-justified in 16-bit registers. Some
824 * Maxim chips use unsigned values.
825 */
826
827static inline int temp_from_s8(s8 val)
828{
829 return val * 1000;
830}
831
832static inline int temp_from_u8(u8 val)
833{
834 return val * 1000;
835}
836
837static inline int temp_from_s16(s16 val)
838{
839 return val / 32 * 125;
840}
841
842static inline int temp_from_u16(u16 val)
843{
844 return val / 32 * 125;
845}
846
847static s8 temp_to_s8(long val)
848{
849 if (val <= -128000)
850 return -128;
851 if (val >= 127000)
852 return 127;
853 if (val < 0)
854 return (val - 500) / 1000;
855 return (val + 500) / 1000;
856}
857
858static u8 temp_to_u8(long val)
859{
860 if (val <= 0)
861 return 0;
862 if (val >= 255000)
863 return 255;
864 return (val + 500) / 1000;
865}
866
867static s16 temp_to_s16(long val)
868{
869 if (val <= -128000)
870 return 0x8000;
871 if (val >= 127875)
872 return 0x7FE0;
873 if (val < 0)
874 return (val - 62) / 125 * 32;
875 return (val + 62) / 125 * 32;
876}
877
878static u8 hyst_to_reg(long val)
879{
880 if (val <= 0)
881 return 0;
882 if (val >= 30500)
883 return 31;
884 return (val + 500) / 1000;
885}
886
887/*
888 * ADT7461 in compatibility mode is almost identical to LM90 except that
889 * attempts to write values that are outside the range 0 < temp < 127 are
890 * treated as the boundary value.
891 *
892 * ADT7461 in "extended mode" operation uses unsigned integers offset by
893 * 64 (e.g., 0 -> -64 degC). The range is restricted to -64..191 degC.
894 */
895static inline int temp_from_u8_adt7461(struct lm90_data *data, u8 val)
896{
897 if (data->flags & LM90_FLAG_ADT7461_EXT)
898 return (val - 64) * 1000;
899 return temp_from_s8(val);
900}
901
902static inline int temp_from_u16_adt7461(struct lm90_data *data, u16 val)
903{
904 if (data->flags & LM90_FLAG_ADT7461_EXT)
905 return (val - 0x4000) / 64 * 250;
906 return temp_from_s16(val);
907}
908
909static u8 temp_to_u8_adt7461(struct lm90_data *data, long val)
910{
911 if (data->flags & LM90_FLAG_ADT7461_EXT) {
912 if (val <= -64000)
913 return 0;
914 if (val >= 191000)
915 return 0xFF;
916 return (val + 500 + 64000) / 1000;
917 }
918 if (val <= 0)
919 return 0;
920 if (val >= 127000)
921 return 127;
922 return (val + 500) / 1000;
923}
924
925static u16 temp_to_u16_adt7461(struct lm90_data *data, long val)
926{
927 if (data->flags & LM90_FLAG_ADT7461_EXT) {
928 if (val <= -64000)
929 return 0;
930 if (val >= 191750)
931 return 0xFFC0;
932 return (val + 64000 + 125) / 250 * 64;
933 }
934 if (val <= 0)
935 return 0;
936 if (val >= 127750)
937 return 0x7FC0;
938 return (val + 125) / 250 * 64;
939}
940
941/* pec used for ADM1032 only */
942static ssize_t pec_show(struct device *dev, struct device_attribute *dummy,
943 char *buf)
944{
945 struct i2c_client *client = to_i2c_client(dev);
946
947 return sprintf(buf, "%d\n", !!(client->flags & I2C_CLIENT_PEC));
948}
949
950static ssize_t pec_store(struct device *dev, struct device_attribute *dummy,
951 const char *buf, size_t count)
952{
953 struct i2c_client *client = to_i2c_client(dev);
954 long val;
955 int err;
956
957 err = kstrtol(buf, 10, &val);
958 if (err < 0)
959 return err;
960
961 switch (val) {
962 case 0:
963 client->flags &= ~I2C_CLIENT_PEC;
964 break;
965 case 1:
966 client->flags |= I2C_CLIENT_PEC;
967 break;
968 default:
969 return -EINVAL;
970 }
971
972 return count;
973}
974
975static DEVICE_ATTR_RW(pec);
976
977static int lm90_get_temp11(struct lm90_data *data, int index)
978{
979 s16 temp11 = data->temp11[index];
980 int temp;
981
982 if (data->kind == adt7461 || data->kind == tmp451)
983 temp = temp_from_u16_adt7461(data, temp11);
984 else if (data->kind == max6646)
985 temp = temp_from_u16(temp11);
986 else
987 temp = temp_from_s16(temp11);
988
989 /* +16 degrees offset for temp2 for the LM99 */
990 if (data->kind == lm99 && index <= 2)
991 temp += 16000;
992
993 return temp;
994}
995
996static int lm90_set_temp11(struct lm90_data *data, int index, long val)
997{
998 static struct reg {
999 u8 high;
1000 u8 low;
1001 } reg[] = {
1002 [REMOTE_LOW] = { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL },
1003 [REMOTE_HIGH] = { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL },
1004 [REMOTE_OFFSET] = { LM90_REG_W_REMOTE_OFFSH, LM90_REG_W_REMOTE_OFFSL },
1005 [REMOTE2_LOW] = { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL },
1006 [REMOTE2_HIGH] = { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL }
1007 };
1008 struct i2c_client *client = data->client;
1009 struct reg *regp = ®[index];
1010 int err;
1011
1012 /* +16 degrees offset for temp2 for the LM99 */
1013 if (data->kind == lm99 && index <= 2)
1014 val -= 16000;
1015
1016 if (data->kind == adt7461 || data->kind == tmp451)
1017 data->temp11[index] = temp_to_u16_adt7461(data, val);
1018 else if (data->kind == max6646)
1019 data->temp11[index] = temp_to_u8(val) << 8;
1020 else if (data->flags & LM90_HAVE_REM_LIMIT_EXT)
1021 data->temp11[index] = temp_to_s16(val);
1022 else
1023 data->temp11[index] = temp_to_s8(val) << 8;
1024
1025 lm90_select_remote_channel(data, index >= 3);
1026 err = i2c_smbus_write_byte_data(client, regp->high,
1027 data->temp11[index] >> 8);
1028 if (err < 0)
1029 return err;
1030 if (data->flags & LM90_HAVE_REM_LIMIT_EXT)
1031 err = i2c_smbus_write_byte_data(client, regp->low,
1032 data->temp11[index] & 0xff);
1033
1034 lm90_select_remote_channel(data, 0);
1035 return err;
1036}
1037
1038static int lm90_get_temp8(struct lm90_data *data, int index)
1039{
1040 s8 temp8 = data->temp8[index];
1041 int temp;
1042
1043 if (data->kind == adt7461 || data->kind == tmp451)
1044 temp = temp_from_u8_adt7461(data, temp8);
1045 else if (data->kind == max6646)
1046 temp = temp_from_u8(temp8);
1047 else
1048 temp = temp_from_s8(temp8);
1049
1050 /* +16 degrees offset for temp2 for the LM99 */
1051 if (data->kind == lm99 && index == 3)
1052 temp += 16000;
1053
1054 return temp;
1055}
1056
1057static int lm90_set_temp8(struct lm90_data *data, int index, long val)
1058{
1059 static const u8 reg[TEMP8_REG_NUM] = {
1060 LM90_REG_W_LOCAL_LOW,
1061 LM90_REG_W_LOCAL_HIGH,
1062 LM90_REG_W_LOCAL_CRIT,
1063 LM90_REG_W_REMOTE_CRIT,
1064 MAX6659_REG_W_LOCAL_EMERG,
1065 MAX6659_REG_W_REMOTE_EMERG,
1066 LM90_REG_W_REMOTE_CRIT,
1067 MAX6659_REG_W_REMOTE_EMERG,
1068 };
1069 struct i2c_client *client = data->client;
1070 int err;
1071
1072 /* +16 degrees offset for temp2 for the LM99 */
1073 if (data->kind == lm99 && index == 3)
1074 val -= 16000;
1075
1076 if (data->kind == adt7461 || data->kind == tmp451)
1077 data->temp8[index] = temp_to_u8_adt7461(data, val);
1078 else if (data->kind == max6646)
1079 data->temp8[index] = temp_to_u8(val);
1080 else
1081 data->temp8[index] = temp_to_s8(val);
1082
1083 lm90_select_remote_channel(data, index >= 6);
1084 err = i2c_smbus_write_byte_data(client, reg[index], data->temp8[index]);
1085 lm90_select_remote_channel(data, 0);
1086
1087 return err;
1088}
1089
1090static int lm90_get_temphyst(struct lm90_data *data, int index)
1091{
1092 int temp;
1093
1094 if (data->kind == adt7461 || data->kind == tmp451)
1095 temp = temp_from_u8_adt7461(data, data->temp8[index]);
1096 else if (data->kind == max6646)
1097 temp = temp_from_u8(data->temp8[index]);
1098 else
1099 temp = temp_from_s8(data->temp8[index]);
1100
1101 /* +16 degrees offset for temp2 for the LM99 */
1102 if (data->kind == lm99 && index == 3)
1103 temp += 16000;
1104
1105 return temp - temp_from_s8(data->temp_hyst);
1106}
1107
1108static int lm90_set_temphyst(struct lm90_data *data, long val)
1109{
1110 struct i2c_client *client = data->client;
1111 int temp;
1112 int err;
1113
1114 if (data->kind == adt7461 || data->kind == tmp451)
1115 temp = temp_from_u8_adt7461(data, data->temp8[LOCAL_CRIT]);
1116 else if (data->kind == max6646)
1117 temp = temp_from_u8(data->temp8[LOCAL_CRIT]);
1118 else
1119 temp = temp_from_s8(data->temp8[LOCAL_CRIT]);
1120
1121 data->temp_hyst = hyst_to_reg(temp - val);
1122 err = i2c_smbus_write_byte_data(client, LM90_REG_W_TCRIT_HYST,
1123 data->temp_hyst);
1124 return err;
1125}
1126
1127static const u8 lm90_temp_index[3] = {
1128 LOCAL_TEMP, REMOTE_TEMP, REMOTE2_TEMP
1129};
1130
1131static const u8 lm90_temp_min_index[3] = {
1132 LOCAL_LOW, REMOTE_LOW, REMOTE2_LOW
1133};
1134
1135static const u8 lm90_temp_max_index[3] = {
1136 LOCAL_HIGH, REMOTE_HIGH, REMOTE2_HIGH
1137};
1138
1139static const u8 lm90_temp_crit_index[3] = {
1140 LOCAL_CRIT, REMOTE_CRIT, REMOTE2_CRIT
1141};
1142
1143static const u8 lm90_temp_emerg_index[3] = {
1144 LOCAL_EMERG, REMOTE_EMERG, REMOTE2_EMERG
1145};
1146
1147static const u8 lm90_min_alarm_bits[3] = { 5, 3, 11 };
1148static const u8 lm90_max_alarm_bits[3] = { 6, 4, 12 };
1149static const u8 lm90_crit_alarm_bits[3] = { 0, 1, 9 };
1150static const u8 lm90_emergency_alarm_bits[3] = { 15, 13, 14 };
1151static const u8 lm90_fault_bits[3] = { 0, 2, 10 };
1152
1153static int lm90_temp_read(struct device *dev, u32 attr, int channel, long *val)
1154{
1155 struct lm90_data *data = dev_get_drvdata(dev);
1156 int err;
1157
1158 mutex_lock(&data->update_lock);
1159 err = lm90_update_device(dev);
1160 mutex_unlock(&data->update_lock);
1161 if (err)
1162 return err;
1163
1164 switch (attr) {
1165 case hwmon_temp_input:
1166 *val = lm90_get_temp11(data, lm90_temp_index[channel]);
1167 break;
1168 case hwmon_temp_min_alarm:
1169 *val = (data->alarms >> lm90_min_alarm_bits[channel]) & 1;
1170 break;
1171 case hwmon_temp_max_alarm:
1172 *val = (data->alarms >> lm90_max_alarm_bits[channel]) & 1;
1173 break;
1174 case hwmon_temp_crit_alarm:
1175 *val = (data->alarms >> lm90_crit_alarm_bits[channel]) & 1;
1176 break;
1177 case hwmon_temp_emergency_alarm:
1178 *val = (data->alarms >> lm90_emergency_alarm_bits[channel]) & 1;
1179 break;
1180 case hwmon_temp_fault:
1181 *val = (data->alarms >> lm90_fault_bits[channel]) & 1;
1182 break;
1183 case hwmon_temp_min:
1184 if (channel == 0)
1185 *val = lm90_get_temp8(data,
1186 lm90_temp_min_index[channel]);
1187 else
1188 *val = lm90_get_temp11(data,
1189 lm90_temp_min_index[channel]);
1190 break;
1191 case hwmon_temp_max:
1192 if (channel == 0)
1193 *val = lm90_get_temp8(data,
1194 lm90_temp_max_index[channel]);
1195 else
1196 *val = lm90_get_temp11(data,
1197 lm90_temp_max_index[channel]);
1198 break;
1199 case hwmon_temp_crit:
1200 *val = lm90_get_temp8(data, lm90_temp_crit_index[channel]);
1201 break;
1202 case hwmon_temp_crit_hyst:
1203 *val = lm90_get_temphyst(data, lm90_temp_crit_index[channel]);
1204 break;
1205 case hwmon_temp_emergency:
1206 *val = lm90_get_temp8(data, lm90_temp_emerg_index[channel]);
1207 break;
1208 case hwmon_temp_emergency_hyst:
1209 *val = lm90_get_temphyst(data, lm90_temp_emerg_index[channel]);
1210 break;
1211 case hwmon_temp_offset:
1212 *val = lm90_get_temp11(data, REMOTE_OFFSET);
1213 break;
1214 default:
1215 return -EOPNOTSUPP;
1216 }
1217 return 0;
1218}
1219
1220static int lm90_temp_write(struct device *dev, u32 attr, int channel, long val)
1221{
1222 struct lm90_data *data = dev_get_drvdata(dev);
1223 int err;
1224
1225 mutex_lock(&data->update_lock);
1226
1227 err = lm90_update_device(dev);
1228 if (err)
1229 goto error;
1230
1231 switch (attr) {
1232 case hwmon_temp_min:
1233 if (channel == 0)
1234 err = lm90_set_temp8(data,
1235 lm90_temp_min_index[channel],
1236 val);
1237 else
1238 err = lm90_set_temp11(data,
1239 lm90_temp_min_index[channel],
1240 val);
1241 break;
1242 case hwmon_temp_max:
1243 if (channel == 0)
1244 err = lm90_set_temp8(data,
1245 lm90_temp_max_index[channel],
1246 val);
1247 else
1248 err = lm90_set_temp11(data,
1249 lm90_temp_max_index[channel],
1250 val);
1251 break;
1252 case hwmon_temp_crit:
1253 err = lm90_set_temp8(data, lm90_temp_crit_index[channel], val);
1254 break;
1255 case hwmon_temp_crit_hyst:
1256 err = lm90_set_temphyst(data, val);
1257 break;
1258 case hwmon_temp_emergency:
1259 err = lm90_set_temp8(data, lm90_temp_emerg_index[channel], val);
1260 break;
1261 case hwmon_temp_offset:
1262 err = lm90_set_temp11(data, REMOTE_OFFSET, val);
1263 break;
1264 default:
1265 err = -EOPNOTSUPP;
1266 break;
1267 }
1268error:
1269 mutex_unlock(&data->update_lock);
1270
1271 return err;
1272}
1273
1274static umode_t lm90_temp_is_visible(const void *data, u32 attr, int channel)
1275{
1276 switch (attr) {
1277 case hwmon_temp_input:
1278 case hwmon_temp_min_alarm:
1279 case hwmon_temp_max_alarm:
1280 case hwmon_temp_crit_alarm:
1281 case hwmon_temp_emergency_alarm:
1282 case hwmon_temp_emergency_hyst:
1283 case hwmon_temp_fault:
1284 return 0444;
1285 case hwmon_temp_min:
1286 case hwmon_temp_max:
1287 case hwmon_temp_crit:
1288 case hwmon_temp_emergency:
1289 case hwmon_temp_offset:
1290 return 0644;
1291 case hwmon_temp_crit_hyst:
1292 if (channel == 0)
1293 return 0644;
1294 return 0444;
1295 default:
1296 return 0;
1297 }
1298}
1299
1300static int lm90_chip_read(struct device *dev, u32 attr, int channel, long *val)
1301{
1302 struct lm90_data *data = dev_get_drvdata(dev);
1303 int err;
1304
1305 mutex_lock(&data->update_lock);
1306 err = lm90_update_device(dev);
1307 mutex_unlock(&data->update_lock);
1308 if (err)
1309 return err;
1310
1311 switch (attr) {
1312 case hwmon_chip_update_interval:
1313 *val = data->update_interval;
1314 break;
1315 case hwmon_chip_alarms:
1316 *val = data->alarms;
1317 break;
1318 default:
1319 return -EOPNOTSUPP;
1320 }
1321
1322 return 0;
1323}
1324
1325static int lm90_chip_write(struct device *dev, u32 attr, int channel, long val)
1326{
1327 struct lm90_data *data = dev_get_drvdata(dev);
1328 struct i2c_client *client = data->client;
1329 int err;
1330
1331 mutex_lock(&data->update_lock);
1332
1333 err = lm90_update_device(dev);
1334 if (err)
1335 goto error;
1336
1337 switch (attr) {
1338 case hwmon_chip_update_interval:
1339 err = lm90_set_convrate(client, data,
1340 clamp_val(val, 0, 100000));
1341 break;
1342 default:
1343 err = -EOPNOTSUPP;
1344 break;
1345 }
1346error:
1347 mutex_unlock(&data->update_lock);
1348
1349 return err;
1350}
1351
1352static umode_t lm90_chip_is_visible(const void *data, u32 attr, int channel)
1353{
1354 switch (attr) {
1355 case hwmon_chip_update_interval:
1356 return 0644;
1357 case hwmon_chip_alarms:
1358 return 0444;
1359 default:
1360 return 0;
1361 }
1362}
1363
1364static int lm90_read(struct device *dev, enum hwmon_sensor_types type,
1365 u32 attr, int channel, long *val)
1366{
1367 switch (type) {
1368 case hwmon_chip:
1369 return lm90_chip_read(dev, attr, channel, val);
1370 case hwmon_temp:
1371 return lm90_temp_read(dev, attr, channel, val);
1372 default:
1373 return -EOPNOTSUPP;
1374 }
1375}
1376
1377static int lm90_write(struct device *dev, enum hwmon_sensor_types type,
1378 u32 attr, int channel, long val)
1379{
1380 switch (type) {
1381 case hwmon_chip:
1382 return lm90_chip_write(dev, attr, channel, val);
1383 case hwmon_temp:
1384 return lm90_temp_write(dev, attr, channel, val);
1385 default:
1386 return -EOPNOTSUPP;
1387 }
1388}
1389
1390static umode_t lm90_is_visible(const void *data, enum hwmon_sensor_types type,
1391 u32 attr, int channel)
1392{
1393 switch (type) {
1394 case hwmon_chip:
1395 return lm90_chip_is_visible(data, attr, channel);
1396 case hwmon_temp:
1397 return lm90_temp_is_visible(data, attr, channel);
1398 default:
1399 return 0;
1400 }
1401}
1402
1403/* Return 0 if detection is successful, -ENODEV otherwise */
1404static int lm90_detect(struct i2c_client *client,
1405 struct i2c_board_info *info)
1406{
1407 struct i2c_adapter *adapter = client->adapter;
1408 int address = client->addr;
1409 const char *name = NULL;
1410 int man_id, chip_id, config1, config2, convrate;
1411
1412 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
1413 return -ENODEV;
1414
1415 /* detection and identification */
1416 man_id = i2c_smbus_read_byte_data(client, LM90_REG_R_MAN_ID);
1417 chip_id = i2c_smbus_read_byte_data(client, LM90_REG_R_CHIP_ID);
1418 config1 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG1);
1419 convrate = i2c_smbus_read_byte_data(client, LM90_REG_R_CONVRATE);
1420 if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0)
1421 return -ENODEV;
1422
1423 if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) {
1424 config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2);
1425 if (config2 < 0)
1426 return -ENODEV;
1427 } else
1428 config2 = 0; /* Make compiler happy */
1429
1430 if ((address == 0x4C || address == 0x4D)
1431 && man_id == 0x01) { /* National Semiconductor */
1432 if ((config1 & 0x2A) == 0x00
1433 && (config2 & 0xF8) == 0x00
1434 && convrate <= 0x09) {
1435 if (address == 0x4C
1436 && (chip_id & 0xF0) == 0x20) { /* LM90 */
1437 name = "lm90";
1438 } else
1439 if ((chip_id & 0xF0) == 0x30) { /* LM89/LM99 */
1440 name = "lm99";
1441 dev_info(&adapter->dev,
1442 "Assuming LM99 chip at 0x%02x\n",
1443 address);
1444 dev_info(&adapter->dev,
1445 "If it is an LM89, instantiate it "
1446 "with the new_device sysfs "
1447 "interface\n");
1448 } else
1449 if (address == 0x4C
1450 && (chip_id & 0xF0) == 0x10) { /* LM86 */
1451 name = "lm86";
1452 }
1453 }
1454 } else
1455 if ((address == 0x4C || address == 0x4D)
1456 && man_id == 0x41) { /* Analog Devices */
1457 if ((chip_id & 0xF0) == 0x40 /* ADM1032 */
1458 && (config1 & 0x3F) == 0x00
1459 && convrate <= 0x0A) {
1460 name = "adm1032";
1461 /*
1462 * The ADM1032 supports PEC, but only if combined
1463 * transactions are not used.
1464 */
1465 if (i2c_check_functionality(adapter,
1466 I2C_FUNC_SMBUS_BYTE))
1467 info->flags |= I2C_CLIENT_PEC;
1468 } else
1469 if (chip_id == 0x51 /* ADT7461 */
1470 && (config1 & 0x1B) == 0x00
1471 && convrate <= 0x0A) {
1472 name = "adt7461";
1473 } else
1474 if (chip_id == 0x57 /* ADT7461A, NCT1008 */
1475 && (config1 & 0x1B) == 0x00
1476 && convrate <= 0x0A) {
1477 name = "adt7461a";
1478 }
1479 } else
1480 if (man_id == 0x4D) { /* Maxim */
1481 int emerg, emerg2, status2;
1482
1483 /*
1484 * We read MAX6659_REG_R_REMOTE_EMERG twice, and re-read
1485 * LM90_REG_R_MAN_ID in between. If MAX6659_REG_R_REMOTE_EMERG
1486 * exists, both readings will reflect the same value. Otherwise,
1487 * the readings will be different.
1488 */
1489 emerg = i2c_smbus_read_byte_data(client,
1490 MAX6659_REG_R_REMOTE_EMERG);
1491 man_id = i2c_smbus_read_byte_data(client,
1492 LM90_REG_R_MAN_ID);
1493 emerg2 = i2c_smbus_read_byte_data(client,
1494 MAX6659_REG_R_REMOTE_EMERG);
1495 status2 = i2c_smbus_read_byte_data(client,
1496 MAX6696_REG_R_STATUS2);
1497 if (emerg < 0 || man_id < 0 || emerg2 < 0 || status2 < 0)
1498 return -ENODEV;
1499
1500 /*
1501 * The MAX6657, MAX6658 and MAX6659 do NOT have a chip_id
1502 * register. Reading from that address will return the last
1503 * read value, which in our case is those of the man_id
1504 * register. Likewise, the config1 register seems to lack a
1505 * low nibble, so the value will be those of the previous
1506 * read, so in our case those of the man_id register.
1507 * MAX6659 has a third set of upper temperature limit registers.
1508 * Those registers also return values on MAX6657 and MAX6658,
1509 * thus the only way to detect MAX6659 is by its address.
1510 * For this reason it will be mis-detected as MAX6657 if its
1511 * address is 0x4C.
1512 */
1513 if (chip_id == man_id
1514 && (address == 0x4C || address == 0x4D || address == 0x4E)
1515 && (config1 & 0x1F) == (man_id & 0x0F)
1516 && convrate <= 0x09) {
1517 if (address == 0x4C)
1518 name = "max6657";
1519 else
1520 name = "max6659";
1521 } else
1522 /*
1523 * Even though MAX6695 and MAX6696 do not have a chip ID
1524 * register, reading it returns 0x01. Bit 4 of the config1
1525 * register is unused and should return zero when read. Bit 0 of
1526 * the status2 register is unused and should return zero when
1527 * read.
1528 *
1529 * MAX6695 and MAX6696 have an additional set of temperature
1530 * limit registers. We can detect those chips by checking if
1531 * one of those registers exists.
1532 */
1533 if (chip_id == 0x01
1534 && (config1 & 0x10) == 0x00
1535 && (status2 & 0x01) == 0x00
1536 && emerg == emerg2
1537 && convrate <= 0x07) {
1538 name = "max6696";
1539 } else
1540 /*
1541 * The chip_id register of the MAX6680 and MAX6681 holds the
1542 * revision of the chip. The lowest bit of the config1 register
1543 * is unused and should return zero when read, so should the
1544 * second to last bit of config1 (software reset).
1545 */
1546 if (chip_id == 0x01
1547 && (config1 & 0x03) == 0x00
1548 && convrate <= 0x07) {
1549 name = "max6680";
1550 } else
1551 /*
1552 * The chip_id register of the MAX6646/6647/6649 holds the
1553 * revision of the chip. The lowest 6 bits of the config1
1554 * register are unused and should return zero when read.
1555 */
1556 if (chip_id == 0x59
1557 && (config1 & 0x3f) == 0x00
1558 && convrate <= 0x07) {
1559 name = "max6646";
1560 }
1561 } else
1562 if (address == 0x4C
1563 && man_id == 0x5C) { /* Winbond/Nuvoton */
1564 if ((config1 & 0x2A) == 0x00
1565 && (config2 & 0xF8) == 0x00) {
1566 if (chip_id == 0x01 /* W83L771W/G */
1567 && convrate <= 0x09) {
1568 name = "w83l771";
1569 } else
1570 if ((chip_id & 0xFE) == 0x10 /* W83L771AWG/ASG */
1571 && convrate <= 0x08) {
1572 name = "w83l771";
1573 }
1574 }
1575 } else
1576 if (address >= 0x48 && address <= 0x4F
1577 && man_id == 0xA1) { /* NXP Semiconductor/Philips */
1578 if (chip_id == 0x00
1579 && (config1 & 0x2A) == 0x00
1580 && (config2 & 0xFE) == 0x00
1581 && convrate <= 0x09) {
1582 name = "sa56004";
1583 }
1584 } else
1585 if ((address == 0x4C || address == 0x4D)
1586 && man_id == 0x47) { /* GMT */
1587 if (chip_id == 0x01 /* G781 */
1588 && (config1 & 0x3F) == 0x00
1589 && convrate <= 0x08)
1590 name = "g781";
1591 } else
1592 if (address == 0x4C
1593 && man_id == 0x55) { /* Texas Instruments */
1594 int local_ext;
1595
1596 local_ext = i2c_smbus_read_byte_data(client,
1597 TMP451_REG_R_LOCAL_TEMPL);
1598
1599 if (chip_id == 0x00 /* TMP451 */
1600 && (config1 & 0x1B) == 0x00
1601 && convrate <= 0x09
1602 && (local_ext & 0x0F) == 0x00)
1603 name = "tmp451";
1604 }
1605
1606 if (!name) { /* identification failed */
1607 dev_dbg(&adapter->dev,
1608 "Unsupported chip at 0x%02x (man_id=0x%02X, "
1609 "chip_id=0x%02X)\n", address, man_id, chip_id);
1610 return -ENODEV;
1611 }
1612
1613 strlcpy(info->type, name, I2C_NAME_SIZE);
1614
1615 return 0;
1616}
1617
1618static void lm90_restore_conf(void *_data)
1619{
1620 struct lm90_data *data = _data;
1621 struct i2c_client *client = data->client;
1622
1623 /* Restore initial configuration */
1624 lm90_write_convrate(data, data->convrate_orig);
1625 i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
1626 data->config_orig);
1627}
1628
1629static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
1630{
1631 int config, convrate;
1632
1633 convrate = lm90_read_reg(client, LM90_REG_R_CONVRATE);
1634 if (convrate < 0)
1635 return convrate;
1636 data->convrate_orig = convrate;
1637
1638 /*
1639 * Start the conversions.
1640 */
1641 config = lm90_read_reg(client, LM90_REG_R_CONFIG1);
1642 if (config < 0)
1643 return config;
1644 data->config_orig = config;
1645 data->config = config;
1646
1647 lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
1648
1649 /* Check Temperature Range Select */
1650 if (data->kind == adt7461 || data->kind == tmp451) {
1651 if (config & 0x04)
1652 data->flags |= LM90_FLAG_ADT7461_EXT;
1653 }
1654
1655 /*
1656 * Put MAX6680/MAX8881 into extended resolution (bit 0x10,
1657 * 0.125 degree resolution) and range (0x08, extend range
1658 * to -64 degree) mode for the remote temperature sensor.
1659 */
1660 if (data->kind == max6680)
1661 config |= 0x18;
1662
1663 /*
1664 * Select external channel 0 for max6695/96
1665 */
1666 if (data->kind == max6696)
1667 config &= ~0x08;
1668
1669 config &= 0xBF; /* run */
1670 lm90_update_confreg(data, config);
1671
1672 return devm_add_action_or_reset(&client->dev, lm90_restore_conf, data);
1673}
1674
1675static bool lm90_is_tripped(struct i2c_client *client, u16 *status)
1676{
1677 struct lm90_data *data = i2c_get_clientdata(client);
1678 int st, st2 = 0;
1679
1680 st = lm90_read_reg(client, LM90_REG_R_STATUS);
1681 if (st < 0)
1682 return false;
1683
1684 if (data->kind == max6696) {
1685 st2 = lm90_read_reg(client, MAX6696_REG_R_STATUS2);
1686 if (st2 < 0)
1687 return false;
1688 }
1689
1690 *status = st | (st2 << 8);
1691
1692 if ((st & 0x7f) == 0 && (st2 & 0xfe) == 0)
1693 return false;
1694
1695 if ((st & (LM90_STATUS_LLOW | LM90_STATUS_LHIGH | LM90_STATUS_LTHRM)) ||
1696 (st2 & MAX6696_STATUS2_LOT2))
1697 dev_warn(&client->dev,
1698 "temp%d out of range, please check!\n", 1);
1699 if ((st & (LM90_STATUS_RLOW | LM90_STATUS_RHIGH | LM90_STATUS_RTHRM)) ||
1700 (st2 & MAX6696_STATUS2_ROT2))
1701 dev_warn(&client->dev,
1702 "temp%d out of range, please check!\n", 2);
1703 if (st & LM90_STATUS_ROPEN)
1704 dev_warn(&client->dev,
1705 "temp%d diode open, please check!\n", 2);
1706 if (st2 & (MAX6696_STATUS2_R2LOW | MAX6696_STATUS2_R2HIGH |
1707 MAX6696_STATUS2_R2THRM | MAX6696_STATUS2_R2OT2))
1708 dev_warn(&client->dev,
1709 "temp%d out of range, please check!\n", 3);
1710 if (st2 & MAX6696_STATUS2_R2OPEN)
1711 dev_warn(&client->dev,
1712 "temp%d diode open, please check!\n", 3);
1713
1714 return true;
1715}
1716
1717static irqreturn_t lm90_irq_thread(int irq, void *dev_id)
1718{
1719 struct i2c_client *client = dev_id;
1720 u16 status;
1721
1722 if (lm90_is_tripped(client, &status))
1723 return IRQ_HANDLED;
1724 else
1725 return IRQ_NONE;
1726}
1727
1728static void lm90_remove_pec(void *dev)
1729{
1730 device_remove_file(dev, &dev_attr_pec);
1731}
1732
1733static void lm90_regulator_disable(void *regulator)
1734{
1735 regulator_disable(regulator);
1736}
1737
1738
1739static const struct hwmon_ops lm90_ops = {
1740 .is_visible = lm90_is_visible,
1741 .read = lm90_read,
1742 .write = lm90_write,
1743};
1744
1745static int lm90_probe(struct i2c_client *client,
1746 const struct i2c_device_id *id)
1747{
1748 struct device *dev = &client->dev;
1749 struct i2c_adapter *adapter = client->adapter;
1750 struct hwmon_channel_info *info;
1751 struct regulator *regulator;
1752 struct device *hwmon_dev;
1753 struct lm90_data *data;
1754 int err;
1755
1756 regulator = devm_regulator_get(dev, "vcc");
1757 if (IS_ERR(regulator))
1758 return PTR_ERR(regulator);
1759
1760 err = regulator_enable(regulator);
1761 if (err < 0) {
1762 dev_err(dev, "Failed to enable regulator: %d\n", err);
1763 return err;
1764 }
1765
1766 err = devm_add_action_or_reset(dev, lm90_regulator_disable, regulator);
1767 if (err)
1768 return err;
1769
1770 data = devm_kzalloc(dev, sizeof(struct lm90_data), GFP_KERNEL);
1771 if (!data)
1772 return -ENOMEM;
1773
1774 data->client = client;
1775 i2c_set_clientdata(client, data);
1776 mutex_init(&data->update_lock);
1777
1778 /* Set the device type */
1779 if (client->dev.of_node)
1780 data->kind = (enum chips)of_device_get_match_data(&client->dev);
1781 else
1782 data->kind = id->driver_data;
1783 if (data->kind == adm1032) {
1784 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
1785 client->flags &= ~I2C_CLIENT_PEC;
1786 }
1787
1788 /*
1789 * Different devices have different alarm bits triggering the
1790 * ALERT# output
1791 */
1792 data->alert_alarms = lm90_params[data->kind].alert_alarms;
1793
1794 /* Set chip capabilities */
1795 data->flags = lm90_params[data->kind].flags;
1796
1797 data->chip.ops = &lm90_ops;
1798 data->chip.info = data->info;
1799
1800 data->info[0] = HWMON_CHANNEL_INFO(chip,
1801 HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL | HWMON_C_ALARMS);
1802 data->info[1] = &data->temp_info;
1803
1804 info = &data->temp_info;
1805 info->type = hwmon_temp;
1806 info->config = data->channel_config;
1807
1808 data->channel_config[0] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
1809 HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
1810 HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM;
1811 data->channel_config[1] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
1812 HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
1813 HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM | HWMON_T_FAULT;
1814
1815 if (data->flags & LM90_HAVE_OFFSET)
1816 data->channel_config[1] |= HWMON_T_OFFSET;
1817
1818 if (data->flags & LM90_HAVE_EMERGENCY) {
1819 data->channel_config[0] |= HWMON_T_EMERGENCY |
1820 HWMON_T_EMERGENCY_HYST;
1821 data->channel_config[1] |= HWMON_T_EMERGENCY |
1822 HWMON_T_EMERGENCY_HYST;
1823 }
1824
1825 if (data->flags & LM90_HAVE_EMERGENCY_ALARM) {
1826 data->channel_config[0] |= HWMON_T_EMERGENCY_ALARM;
1827 data->channel_config[1] |= HWMON_T_EMERGENCY_ALARM;
1828 }
1829
1830 if (data->flags & LM90_HAVE_TEMP3) {
1831 data->channel_config[2] = HWMON_T_INPUT |
1832 HWMON_T_MIN | HWMON_T_MAX |
1833 HWMON_T_CRIT | HWMON_T_CRIT_HYST |
1834 HWMON_T_EMERGENCY | HWMON_T_EMERGENCY_HYST |
1835 HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM |
1836 HWMON_T_CRIT_ALARM | HWMON_T_EMERGENCY_ALARM |
1837 HWMON_T_FAULT;
1838 }
1839
1840 data->reg_local_ext = lm90_params[data->kind].reg_local_ext;
1841
1842 /* Set maximum conversion rate */
1843 data->max_convrate = lm90_params[data->kind].max_convrate;
1844
1845 /* Initialize the LM90 chip */
1846 err = lm90_init_client(client, data);
1847 if (err < 0) {
1848 dev_err(dev, "Failed to initialize device\n");
1849 return err;
1850 }
1851
1852 /*
1853 * The 'pec' attribute is attached to the i2c device and thus created
1854 * separately.
1855 */
1856 if (client->flags & I2C_CLIENT_PEC) {
1857 err = device_create_file(dev, &dev_attr_pec);
1858 if (err)
1859 return err;
1860 err = devm_add_action_or_reset(dev, lm90_remove_pec, dev);
1861 if (err)
1862 return err;
1863 }
1864
1865 hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
1866 data, &data->chip,
1867 NULL);
1868 if (IS_ERR(hwmon_dev))
1869 return PTR_ERR(hwmon_dev);
1870
1871 if (client->irq) {
1872 dev_dbg(dev, "IRQ: %d\n", client->irq);
1873 err = devm_request_threaded_irq(dev, client->irq,
1874 NULL, lm90_irq_thread,
1875 IRQF_TRIGGER_LOW | IRQF_ONESHOT,
1876 "lm90", client);
1877 if (err < 0) {
1878 dev_err(dev, "cannot request IRQ %d\n", client->irq);
1879 return err;
1880 }
1881 }
1882
1883 return 0;
1884}
1885
1886static void lm90_alert(struct i2c_client *client, enum i2c_alert_protocol type,
1887 unsigned int flag)
1888{
1889 u16 alarms;
1890
1891 if (type != I2C_PROTOCOL_SMBUS_ALERT)
1892 return;
1893
1894 if (lm90_is_tripped(client, &alarms)) {
1895 /*
1896 * Disable ALERT# output, because these chips don't implement
1897 * SMBus alert correctly; they should only hold the alert line
1898 * low briefly.
1899 */
1900 struct lm90_data *data = i2c_get_clientdata(client);
1901
1902 if ((data->flags & LM90_HAVE_BROKEN_ALERT) &&
1903 (alarms & data->alert_alarms)) {
1904 dev_dbg(&client->dev, "Disabling ALERT#\n");
1905 lm90_update_confreg(data, data->config | 0x80);
1906 }
1907 } else {
1908 dev_info(&client->dev, "Everything OK\n");
1909 }
1910}
1911
1912static struct i2c_driver lm90_driver = {
1913 .class = I2C_CLASS_HWMON,
1914 .driver = {
1915 .name = "lm90",
1916 .of_match_table = of_match_ptr(lm90_of_match),
1917 },
1918 .probe = lm90_probe,
1919 .alert = lm90_alert,
1920 .id_table = lm90_id,
1921 .detect = lm90_detect,
1922 .address_list = normal_i2c,
1923};
1924
1925module_i2c_driver(lm90_driver);
1926
1927MODULE_AUTHOR("Jean Delvare <jdelvare@suse.de>");
1928MODULE_DESCRIPTION("LM90/ADM1032 driver");
1929MODULE_LICENSE("GPL");