Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/************************************************************************
3 * Copyright 2003 Digi International (www.digi.com)
4 *
5 * Copyright (C) 2004 IBM Corporation. All rights reserved.
6 *
7 * Contact Information:
8 * Scott H Kilau <Scott_Kilau@digi.com>
9 * Wendy Xiong <wendyx@us.ibm.com>
10 *
11 ***********************************************************************/
12#include <linux/delay.h> /* For udelay */
13#include <linux/serial_reg.h> /* For the various UART offsets */
14#include <linux/tty.h>
15#include <linux/pci.h>
16#include <asm/io.h>
17
18#include "jsm.h" /* Driver main header file */
19
20static u32 jsm_offset_table[8] = { 0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80 };
21
22/*
23 * This function allows calls to ensure that all outstanding
24 * PCI writes have been completed, by doing a PCI read against
25 * a non-destructive, read-only location on the Neo card.
26 *
27 * In this case, we are reading the DVID (Read-only Device Identification)
28 * value of the Neo card.
29 */
30static inline void neo_pci_posting_flush(struct jsm_board *bd)
31{
32 readb(bd->re_map_membase + 0x8D);
33}
34
35static void neo_set_cts_flow_control(struct jsm_channel *ch)
36{
37 u8 ier, efr;
38 ier = readb(&ch->ch_neo_uart->ier);
39 efr = readb(&ch->ch_neo_uart->efr);
40
41 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting CTSFLOW\n");
42
43 /* Turn on auto CTS flow control */
44 ier |= (UART_17158_IER_CTSDSR);
45 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_CTSDSR);
46
47 /* Turn off auto Xon flow control */
48 efr &= ~(UART_17158_EFR_IXON);
49
50 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
51 writeb(0, &ch->ch_neo_uart->efr);
52
53 /* Turn on UART enhanced bits */
54 writeb(efr, &ch->ch_neo_uart->efr);
55
56 /* Turn on table D, with 8 char hi/low watermarks */
57 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY), &ch->ch_neo_uart->fctr);
58
59 /* Feed the UART our trigger levels */
60 writeb(8, &ch->ch_neo_uart->tfifo);
61 ch->ch_t_tlevel = 8;
62
63 writeb(ier, &ch->ch_neo_uart->ier);
64}
65
66static void neo_set_rts_flow_control(struct jsm_channel *ch)
67{
68 u8 ier, efr;
69 ier = readb(&ch->ch_neo_uart->ier);
70 efr = readb(&ch->ch_neo_uart->efr);
71
72 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting RTSFLOW\n");
73
74 /* Turn on auto RTS flow control */
75 ier |= (UART_17158_IER_RTSDTR);
76 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_RTSDTR);
77
78 /* Turn off auto Xoff flow control */
79 ier &= ~(UART_17158_IER_XOFF);
80 efr &= ~(UART_17158_EFR_IXOFF);
81
82 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
83 writeb(0, &ch->ch_neo_uart->efr);
84
85 /* Turn on UART enhanced bits */
86 writeb(efr, &ch->ch_neo_uart->efr);
87
88 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY), &ch->ch_neo_uart->fctr);
89 ch->ch_r_watermark = 4;
90
91 writeb(56, &ch->ch_neo_uart->rfifo);
92 ch->ch_r_tlevel = 56;
93
94 writeb(ier, &ch->ch_neo_uart->ier);
95
96 /*
97 * From the Neo UART spec sheet:
98 * The auto RTS/DTR function must be started by asserting
99 * RTS/DTR# output pin (MCR bit-0 or 1 to logic 1 after
100 * it is enabled.
101 */
102 ch->ch_mostat |= (UART_MCR_RTS);
103}
104
105
106static void neo_set_ixon_flow_control(struct jsm_channel *ch)
107{
108 u8 ier, efr;
109 ier = readb(&ch->ch_neo_uart->ier);
110 efr = readb(&ch->ch_neo_uart->efr);
111
112 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting IXON FLOW\n");
113
114 /* Turn off auto CTS flow control */
115 ier &= ~(UART_17158_IER_CTSDSR);
116 efr &= ~(UART_17158_EFR_CTSDSR);
117
118 /* Turn on auto Xon flow control */
119 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXON);
120
121 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
122 writeb(0, &ch->ch_neo_uart->efr);
123
124 /* Turn on UART enhanced bits */
125 writeb(efr, &ch->ch_neo_uart->efr);
126
127 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
128 ch->ch_r_watermark = 4;
129
130 writeb(32, &ch->ch_neo_uart->rfifo);
131 ch->ch_r_tlevel = 32;
132
133 /* Tell UART what start/stop chars it should be looking for */
134 writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
135 writeb(0, &ch->ch_neo_uart->xonchar2);
136
137 writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1);
138 writeb(0, &ch->ch_neo_uart->xoffchar2);
139
140 writeb(ier, &ch->ch_neo_uart->ier);
141}
142
143static void neo_set_ixoff_flow_control(struct jsm_channel *ch)
144{
145 u8 ier, efr;
146 ier = readb(&ch->ch_neo_uart->ier);
147 efr = readb(&ch->ch_neo_uart->efr);
148
149 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting IXOFF FLOW\n");
150
151 /* Turn off auto RTS flow control */
152 ier &= ~(UART_17158_IER_RTSDTR);
153 efr &= ~(UART_17158_EFR_RTSDTR);
154
155 /* Turn on auto Xoff flow control */
156 ier |= (UART_17158_IER_XOFF);
157 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXOFF);
158
159 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
160 writeb(0, &ch->ch_neo_uart->efr);
161
162 /* Turn on UART enhanced bits */
163 writeb(efr, &ch->ch_neo_uart->efr);
164
165 /* Turn on table D, with 8 char hi/low watermarks */
166 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
167
168 writeb(8, &ch->ch_neo_uart->tfifo);
169 ch->ch_t_tlevel = 8;
170
171 /* Tell UART what start/stop chars it should be looking for */
172 writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
173 writeb(0, &ch->ch_neo_uart->xonchar2);
174
175 writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1);
176 writeb(0, &ch->ch_neo_uart->xoffchar2);
177
178 writeb(ier, &ch->ch_neo_uart->ier);
179}
180
181static void neo_set_no_input_flow_control(struct jsm_channel *ch)
182{
183 u8 ier, efr;
184 ier = readb(&ch->ch_neo_uart->ier);
185 efr = readb(&ch->ch_neo_uart->efr);
186
187 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Unsetting Input FLOW\n");
188
189 /* Turn off auto RTS flow control */
190 ier &= ~(UART_17158_IER_RTSDTR);
191 efr &= ~(UART_17158_EFR_RTSDTR);
192
193 /* Turn off auto Xoff flow control */
194 ier &= ~(UART_17158_IER_XOFF);
195 if (ch->ch_c_iflag & IXON)
196 efr &= ~(UART_17158_EFR_IXOFF);
197 else
198 efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXOFF);
199
200 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
201 writeb(0, &ch->ch_neo_uart->efr);
202
203 /* Turn on UART enhanced bits */
204 writeb(efr, &ch->ch_neo_uart->efr);
205
206 /* Turn on table D, with 8 char hi/low watermarks */
207 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
208
209 ch->ch_r_watermark = 0;
210
211 writeb(16, &ch->ch_neo_uart->tfifo);
212 ch->ch_t_tlevel = 16;
213
214 writeb(16, &ch->ch_neo_uart->rfifo);
215 ch->ch_r_tlevel = 16;
216
217 writeb(ier, &ch->ch_neo_uart->ier);
218}
219
220static void neo_set_no_output_flow_control(struct jsm_channel *ch)
221{
222 u8 ier, efr;
223 ier = readb(&ch->ch_neo_uart->ier);
224 efr = readb(&ch->ch_neo_uart->efr);
225
226 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Unsetting Output FLOW\n");
227
228 /* Turn off auto CTS flow control */
229 ier &= ~(UART_17158_IER_CTSDSR);
230 efr &= ~(UART_17158_EFR_CTSDSR);
231
232 /* Turn off auto Xon flow control */
233 if (ch->ch_c_iflag & IXOFF)
234 efr &= ~(UART_17158_EFR_IXON);
235 else
236 efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXON);
237
238 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
239 writeb(0, &ch->ch_neo_uart->efr);
240
241 /* Turn on UART enhanced bits */
242 writeb(efr, &ch->ch_neo_uart->efr);
243
244 /* Turn on table D, with 8 char hi/low watermarks */
245 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
246
247 ch->ch_r_watermark = 0;
248
249 writeb(16, &ch->ch_neo_uart->tfifo);
250 ch->ch_t_tlevel = 16;
251
252 writeb(16, &ch->ch_neo_uart->rfifo);
253 ch->ch_r_tlevel = 16;
254
255 writeb(ier, &ch->ch_neo_uart->ier);
256}
257
258static inline void neo_set_new_start_stop_chars(struct jsm_channel *ch)
259{
260
261 /* if hardware flow control is set, then skip this whole thing */
262 if (ch->ch_c_cflag & CRTSCTS)
263 return;
264
265 jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "start\n");
266
267 /* Tell UART what start/stop chars it should be looking for */
268 writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
269 writeb(0, &ch->ch_neo_uart->xonchar2);
270
271 writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1);
272 writeb(0, &ch->ch_neo_uart->xoffchar2);
273}
274
275static void neo_copy_data_from_uart_to_queue(struct jsm_channel *ch)
276{
277 int qleft = 0;
278 u8 linestatus = 0;
279 u8 error_mask = 0;
280 int n = 0;
281 int total = 0;
282 u16 head;
283 u16 tail;
284
285 /* cache head and tail of queue */
286 head = ch->ch_r_head & RQUEUEMASK;
287 tail = ch->ch_r_tail & RQUEUEMASK;
288
289 /* Get our cached LSR */
290 linestatus = ch->ch_cached_lsr;
291 ch->ch_cached_lsr = 0;
292
293 /* Store how much space we have left in the queue */
294 qleft = tail - head - 1;
295 if (qleft < 0)
296 qleft += RQUEUEMASK + 1;
297
298 /*
299 * If the UART is not in FIFO mode, force the FIFO copy to
300 * NOT be run, by setting total to 0.
301 *
302 * On the other hand, if the UART IS in FIFO mode, then ask
303 * the UART to give us an approximation of data it has RX'ed.
304 */
305 if (!(ch->ch_flags & CH_FIFO_ENABLED))
306 total = 0;
307 else {
308 total = readb(&ch->ch_neo_uart->rfifo);
309
310 /*
311 * EXAR chip bug - RX FIFO COUNT - Fudge factor.
312 *
313 * This resolves a problem/bug with the Exar chip that sometimes
314 * returns a bogus value in the rfifo register.
315 * The count can be any where from 0-3 bytes "off".
316 * Bizarre, but true.
317 */
318 total -= 3;
319 }
320
321 /*
322 * Finally, bound the copy to make sure we don't overflow
323 * our own queue...
324 * The byte by byte copy loop below this loop this will
325 * deal with the queue overflow possibility.
326 */
327 total = min(total, qleft);
328
329 while (total > 0) {
330 /*
331 * Grab the linestatus register, we need to check
332 * to see if there are any errors in the FIFO.
333 */
334 linestatus = readb(&ch->ch_neo_uart->lsr);
335
336 /*
337 * Break out if there is a FIFO error somewhere.
338 * This will allow us to go byte by byte down below,
339 * finding the exact location of the error.
340 */
341 if (linestatus & UART_17158_RX_FIFO_DATA_ERROR)
342 break;
343
344 /* Make sure we don't go over the end of our queue */
345 n = min(((u32) total), (RQUEUESIZE - (u32) head));
346
347 /*
348 * Cut down n even further if needed, this is to fix
349 * a problem with memcpy_fromio() with the Neo on the
350 * IBM pSeries platform.
351 * 15 bytes max appears to be the magic number.
352 */
353 n = min((u32) n, (u32) 12);
354
355 /*
356 * Since we are grabbing the linestatus register, which
357 * will reset some bits after our read, we need to ensure
358 * we don't miss our TX FIFO emptys.
359 */
360 if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR))
361 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
362
363 linestatus = 0;
364
365 /* Copy data from uart to the queue */
366 memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, n);
367 /*
368 * Since RX_FIFO_DATA_ERROR was 0, we are guaranteed
369 * that all the data currently in the FIFO is free of
370 * breaks and parity/frame/orun errors.
371 */
372 memset(ch->ch_equeue + head, 0, n);
373
374 /* Add to and flip head if needed */
375 head = (head + n) & RQUEUEMASK;
376 total -= n;
377 qleft -= n;
378 ch->ch_rxcount += n;
379 }
380
381 /*
382 * Create a mask to determine whether we should
383 * insert the character (if any) into our queue.
384 */
385 if (ch->ch_c_iflag & IGNBRK)
386 error_mask |= UART_LSR_BI;
387
388 /*
389 * Now cleanup any leftover bytes still in the UART.
390 * Also deal with any possible queue overflow here as well.
391 */
392 while (1) {
393
394 /*
395 * Its possible we have a linestatus from the loop above
396 * this, so we "OR" on any extra bits.
397 */
398 linestatus |= readb(&ch->ch_neo_uart->lsr);
399
400 /*
401 * If the chip tells us there is no more data pending to
402 * be read, we can then leave.
403 * But before we do, cache the linestatus, just in case.
404 */
405 if (!(linestatus & UART_LSR_DR)) {
406 ch->ch_cached_lsr = linestatus;
407 break;
408 }
409
410 /* No need to store this bit */
411 linestatus &= ~UART_LSR_DR;
412
413 /*
414 * Since we are grabbing the linestatus register, which
415 * will reset some bits after our read, we need to ensure
416 * we don't miss our TX FIFO emptys.
417 */
418 if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR)) {
419 linestatus &= ~(UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR);
420 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
421 }
422
423 /*
424 * Discard character if we are ignoring the error mask.
425 */
426 if (linestatus & error_mask) {
427 u8 discard;
428 linestatus = 0;
429 memcpy_fromio(&discard, &ch->ch_neo_uart->txrxburst, 1);
430 continue;
431 }
432
433 /*
434 * If our queue is full, we have no choice but to drop some data.
435 * The assumption is that HWFLOW or SWFLOW should have stopped
436 * things way way before we got to this point.
437 *
438 * I decided that I wanted to ditch the oldest data first,
439 * I hope thats okay with everyone? Yes? Good.
440 */
441 while (qleft < 1) {
442 jsm_dbg(READ, &ch->ch_bd->pci_dev,
443 "Queue full, dropping DATA:%x LSR:%x\n",
444 ch->ch_rqueue[tail], ch->ch_equeue[tail]);
445
446 ch->ch_r_tail = tail = (tail + 1) & RQUEUEMASK;
447 ch->ch_err_overrun++;
448 qleft++;
449 }
450
451 memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, 1);
452 ch->ch_equeue[head] = (u8) linestatus;
453
454 jsm_dbg(READ, &ch->ch_bd->pci_dev, "DATA/LSR pair: %x %x\n",
455 ch->ch_rqueue[head], ch->ch_equeue[head]);
456
457 /* Ditch any remaining linestatus value. */
458 linestatus = 0;
459
460 /* Add to and flip head if needed */
461 head = (head + 1) & RQUEUEMASK;
462
463 qleft--;
464 ch->ch_rxcount++;
465 }
466
467 /*
468 * Write new final heads to channel structure.
469 */
470 ch->ch_r_head = head & RQUEUEMASK;
471 ch->ch_e_head = head & EQUEUEMASK;
472 jsm_input(ch);
473}
474
475static void neo_copy_data_from_queue_to_uart(struct jsm_channel *ch)
476{
477 u16 head;
478 u16 tail;
479 int n;
480 int s;
481 int qlen;
482 u32 len_written = 0;
483 struct circ_buf *circ;
484
485 if (!ch)
486 return;
487
488 circ = &ch->uart_port.state->xmit;
489
490 /* No data to write to the UART */
491 if (uart_circ_empty(circ))
492 return;
493
494 /* If port is "stopped", don't send any data to the UART */
495 if ((ch->ch_flags & CH_STOP) || (ch->ch_flags & CH_BREAK_SENDING))
496 return;
497 /*
498 * If FIFOs are disabled. Send data directly to txrx register
499 */
500 if (!(ch->ch_flags & CH_FIFO_ENABLED)) {
501 u8 lsrbits = readb(&ch->ch_neo_uart->lsr);
502
503 ch->ch_cached_lsr |= lsrbits;
504 if (ch->ch_cached_lsr & UART_LSR_THRE) {
505 ch->ch_cached_lsr &= ~(UART_LSR_THRE);
506
507 writeb(circ->buf[circ->tail], &ch->ch_neo_uart->txrx);
508 jsm_dbg(WRITE, &ch->ch_bd->pci_dev,
509 "Tx data: %x\n", circ->buf[circ->tail]);
510 circ->tail = (circ->tail + 1) & (UART_XMIT_SIZE - 1);
511 ch->ch_txcount++;
512 }
513 return;
514 }
515
516 /*
517 * We have to do it this way, because of the EXAR TXFIFO count bug.
518 */
519 if (!(ch->ch_flags & (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM)))
520 return;
521
522 n = UART_17158_TX_FIFOSIZE - ch->ch_t_tlevel;
523
524 /* cache head and tail of queue */
525 head = circ->head & (UART_XMIT_SIZE - 1);
526 tail = circ->tail & (UART_XMIT_SIZE - 1);
527 qlen = uart_circ_chars_pending(circ);
528
529 /* Find minimum of the FIFO space, versus queue length */
530 n = min(n, qlen);
531
532 while (n > 0) {
533
534 s = ((head >= tail) ? head : UART_XMIT_SIZE) - tail;
535 s = min(s, n);
536
537 if (s <= 0)
538 break;
539
540 memcpy_toio(&ch->ch_neo_uart->txrxburst, circ->buf + tail, s);
541 /* Add and flip queue if needed */
542 tail = (tail + s) & (UART_XMIT_SIZE - 1);
543 n -= s;
544 ch->ch_txcount += s;
545 len_written += s;
546 }
547
548 /* Update the final tail */
549 circ->tail = tail & (UART_XMIT_SIZE - 1);
550
551 if (len_written >= ch->ch_t_tlevel)
552 ch->ch_flags &= ~(CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
553
554 if (uart_circ_empty(circ))
555 uart_write_wakeup(&ch->uart_port);
556}
557
558static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
559{
560 u8 msignals = signals;
561
562 jsm_dbg(MSIGS, &ch->ch_bd->pci_dev,
563 "neo_parse_modem: port: %d msignals: %x\n",
564 ch->ch_portnum, msignals);
565
566 /* Scrub off lower bits. They signify delta's, which I don't care about */
567 /* Keep DDCD and DDSR though */
568 msignals &= 0xf8;
569
570 if (msignals & UART_MSR_DDCD)
571 uart_handle_dcd_change(&ch->uart_port, msignals & UART_MSR_DCD);
572 if (msignals & UART_MSR_DDSR)
573 uart_handle_cts_change(&ch->uart_port, msignals & UART_MSR_CTS);
574 if (msignals & UART_MSR_DCD)
575 ch->ch_mistat |= UART_MSR_DCD;
576 else
577 ch->ch_mistat &= ~UART_MSR_DCD;
578
579 if (msignals & UART_MSR_DSR)
580 ch->ch_mistat |= UART_MSR_DSR;
581 else
582 ch->ch_mistat &= ~UART_MSR_DSR;
583
584 if (msignals & UART_MSR_RI)
585 ch->ch_mistat |= UART_MSR_RI;
586 else
587 ch->ch_mistat &= ~UART_MSR_RI;
588
589 if (msignals & UART_MSR_CTS)
590 ch->ch_mistat |= UART_MSR_CTS;
591 else
592 ch->ch_mistat &= ~UART_MSR_CTS;
593
594 jsm_dbg(MSIGS, &ch->ch_bd->pci_dev,
595 "Port: %d DTR: %d RTS: %d CTS: %d DSR: %d " "RI: %d CD: %d\n",
596 ch->ch_portnum,
597 !!((ch->ch_mistat | ch->ch_mostat) & UART_MCR_DTR),
598 !!((ch->ch_mistat | ch->ch_mostat) & UART_MCR_RTS),
599 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_CTS),
600 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_DSR),
601 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_RI),
602 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_DCD));
603}
604
605/* Make the UART raise any of the output signals we want up */
606static void neo_assert_modem_signals(struct jsm_channel *ch)
607{
608 if (!ch)
609 return;
610
611 writeb(ch->ch_mostat, &ch->ch_neo_uart->mcr);
612
613 /* flush write operation */
614 neo_pci_posting_flush(ch->ch_bd);
615}
616
617/*
618 * Flush the WRITE FIFO on the Neo.
619 *
620 * NOTE: Channel lock MUST be held before calling this function!
621 */
622static void neo_flush_uart_write(struct jsm_channel *ch)
623{
624 u8 tmp = 0;
625 int i = 0;
626
627 if (!ch)
628 return;
629
630 writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_XMIT), &ch->ch_neo_uart->isr_fcr);
631
632 for (i = 0; i < 10; i++) {
633
634 /* Check to see if the UART feels it completely flushed the FIFO. */
635 tmp = readb(&ch->ch_neo_uart->isr_fcr);
636 if (tmp & UART_FCR_CLEAR_XMIT) {
637 jsm_dbg(IOCTL, &ch->ch_bd->pci_dev,
638 "Still flushing TX UART... i: %d\n", i);
639 udelay(10);
640 }
641 else
642 break;
643 }
644
645 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
646}
647
648
649/*
650 * Flush the READ FIFO on the Neo.
651 *
652 * NOTE: Channel lock MUST be held before calling this function!
653 */
654static void neo_flush_uart_read(struct jsm_channel *ch)
655{
656 u8 tmp = 0;
657 int i = 0;
658
659 if (!ch)
660 return;
661
662 writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR), &ch->ch_neo_uart->isr_fcr);
663
664 for (i = 0; i < 10; i++) {
665
666 /* Check to see if the UART feels it completely flushed the FIFO. */
667 tmp = readb(&ch->ch_neo_uart->isr_fcr);
668 if (tmp & 2) {
669 jsm_dbg(IOCTL, &ch->ch_bd->pci_dev,
670 "Still flushing RX UART... i: %d\n", i);
671 udelay(10);
672 }
673 else
674 break;
675 }
676}
677
678/*
679 * No locks are assumed to be held when calling this function.
680 */
681static void neo_clear_break(struct jsm_channel *ch)
682{
683 unsigned long lock_flags;
684
685 spin_lock_irqsave(&ch->ch_lock, lock_flags);
686
687 /* Turn break off, and unset some variables */
688 if (ch->ch_flags & CH_BREAK_SENDING) {
689 u8 temp = readb(&ch->ch_neo_uart->lcr);
690 writeb((temp & ~UART_LCR_SBC), &ch->ch_neo_uart->lcr);
691
692 ch->ch_flags &= ~(CH_BREAK_SENDING);
693 jsm_dbg(IOCTL, &ch->ch_bd->pci_dev,
694 "clear break Finishing UART_LCR_SBC! finished: %lx\n",
695 jiffies);
696
697 /* flush write operation */
698 neo_pci_posting_flush(ch->ch_bd);
699 }
700 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
701}
702
703/*
704 * Parse the ISR register.
705 */
706static void neo_parse_isr(struct jsm_board *brd, u32 port)
707{
708 struct jsm_channel *ch;
709 u8 isr;
710 u8 cause;
711 unsigned long lock_flags;
712
713 if (!brd)
714 return;
715
716 if (port >= brd->maxports)
717 return;
718
719 ch = brd->channels[port];
720 if (!ch)
721 return;
722
723 /* Here we try to figure out what caused the interrupt to happen */
724 while (1) {
725
726 isr = readb(&ch->ch_neo_uart->isr_fcr);
727
728 /* Bail if no pending interrupt */
729 if (isr & UART_IIR_NO_INT)
730 break;
731
732 /*
733 * Yank off the upper 2 bits, which just show that the FIFO's are enabled.
734 */
735 isr &= ~(UART_17158_IIR_FIFO_ENABLED);
736
737 jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d isr: %x\n",
738 __FILE__, __LINE__, isr);
739
740 if (isr & (UART_17158_IIR_RDI_TIMEOUT | UART_IIR_RDI)) {
741 /* Read data from uart -> queue */
742 neo_copy_data_from_uart_to_queue(ch);
743
744 /* Call our tty layer to enforce queue flow control if needed. */
745 spin_lock_irqsave(&ch->ch_lock, lock_flags);
746 jsm_check_queue_flow_control(ch);
747 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
748 }
749
750 if (isr & UART_IIR_THRI) {
751 /* Transfer data (if any) from Write Queue -> UART. */
752 spin_lock_irqsave(&ch->ch_lock, lock_flags);
753 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
754 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
755 neo_copy_data_from_queue_to_uart(ch);
756 }
757
758 if (isr & UART_17158_IIR_XONXOFF) {
759 cause = readb(&ch->ch_neo_uart->xoffchar1);
760
761 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
762 "Port %d. Got ISR_XONXOFF: cause:%x\n",
763 port, cause);
764
765 /*
766 * Since the UART detected either an XON or
767 * XOFF match, we need to figure out which
768 * one it was, so we can suspend or resume data flow.
769 */
770 spin_lock_irqsave(&ch->ch_lock, lock_flags);
771 if (cause == UART_17158_XON_DETECT) {
772 /* Is output stopped right now, if so, resume it */
773 if (brd->channels[port]->ch_flags & CH_STOP) {
774 ch->ch_flags &= ~(CH_STOP);
775 }
776 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
777 "Port %d. XON detected in incoming data\n",
778 port);
779 }
780 else if (cause == UART_17158_XOFF_DETECT) {
781 if (!(brd->channels[port]->ch_flags & CH_STOP)) {
782 ch->ch_flags |= CH_STOP;
783 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
784 "Setting CH_STOP\n");
785 }
786 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
787 "Port: %d. XOFF detected in incoming data\n",
788 port);
789 }
790 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
791 }
792
793 if (isr & UART_17158_IIR_HWFLOW_STATE_CHANGE) {
794 /*
795 * If we get here, this means the hardware is doing auto flow control.
796 * Check to see whether RTS/DTR or CTS/DSR caused this interrupt.
797 */
798 cause = readb(&ch->ch_neo_uart->mcr);
799
800 /* Which pin is doing auto flow? RTS or DTR? */
801 spin_lock_irqsave(&ch->ch_lock, lock_flags);
802 if ((cause & 0x4) == 0) {
803 if (cause & UART_MCR_RTS)
804 ch->ch_mostat |= UART_MCR_RTS;
805 else
806 ch->ch_mostat &= ~(UART_MCR_RTS);
807 } else {
808 if (cause & UART_MCR_DTR)
809 ch->ch_mostat |= UART_MCR_DTR;
810 else
811 ch->ch_mostat &= ~(UART_MCR_DTR);
812 }
813 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
814 }
815
816 /* Parse any modem signal changes */
817 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
818 "MOD_STAT: sending to parse_modem_sigs\n");
819 uart_port_lock_irqsave(&ch->uart_port, &lock_flags);
820 neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr));
821 uart_port_unlock_irqrestore(&ch->uart_port, lock_flags);
822 }
823}
824
825static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
826{
827 struct jsm_channel *ch;
828 int linestatus;
829 unsigned long lock_flags;
830
831 if (!brd)
832 return;
833
834 if (port >= brd->maxports)
835 return;
836
837 ch = brd->channels[port];
838 if (!ch)
839 return;
840
841 linestatus = readb(&ch->ch_neo_uart->lsr);
842
843 jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d port: %d linestatus: %x\n",
844 __FILE__, __LINE__, port, linestatus);
845
846 ch->ch_cached_lsr |= linestatus;
847
848 if (ch->ch_cached_lsr & UART_LSR_DR) {
849 /* Read data from uart -> queue */
850 neo_copy_data_from_uart_to_queue(ch);
851 spin_lock_irqsave(&ch->ch_lock, lock_flags);
852 jsm_check_queue_flow_control(ch);
853 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
854 }
855
856 /*
857 * This is a special flag. It indicates that at least 1
858 * RX error (parity, framing, or break) has happened.
859 * Mark this in our struct, which will tell me that I have
860 *to do the special RX+LSR read for this FIFO load.
861 */
862 if (linestatus & UART_17158_RX_FIFO_DATA_ERROR)
863 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
864 "%s:%d Port: %d Got an RX error, need to parse LSR\n",
865 __FILE__, __LINE__, port);
866
867 /*
868 * The next 3 tests should *NOT* happen, as the above test
869 * should encapsulate all 3... At least, thats what Exar says.
870 */
871
872 if (linestatus & UART_LSR_PE) {
873 ch->ch_err_parity++;
874 jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d Port: %d. PAR ERR!\n",
875 __FILE__, __LINE__, port);
876 }
877
878 if (linestatus & UART_LSR_FE) {
879 ch->ch_err_frame++;
880 jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d Port: %d. FRM ERR!\n",
881 __FILE__, __LINE__, port);
882 }
883
884 if (linestatus & UART_LSR_BI) {
885 ch->ch_err_break++;
886 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
887 "%s:%d Port: %d. BRK INTR!\n",
888 __FILE__, __LINE__, port);
889 }
890
891 if (linestatus & UART_LSR_OE) {
892 /*
893 * Rx Oruns. Exar says that an orun will NOT corrupt
894 * the FIFO. It will just replace the holding register
895 * with this new data byte. So basically just ignore this.
896 * Probably we should eventually have an orun stat in our driver...
897 */
898 ch->ch_err_overrun++;
899 jsm_dbg(INTR, &ch->ch_bd->pci_dev,
900 "%s:%d Port: %d. Rx Overrun!\n",
901 __FILE__, __LINE__, port);
902 }
903
904 if (linestatus & UART_LSR_THRE) {
905 spin_lock_irqsave(&ch->ch_lock, lock_flags);
906 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
907 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
908
909 /* Transfer data (if any) from Write Queue -> UART. */
910 neo_copy_data_from_queue_to_uart(ch);
911 }
912 else if (linestatus & UART_17158_TX_AND_FIFO_CLR) {
913 spin_lock_irqsave(&ch->ch_lock, lock_flags);
914 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
915 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
916
917 /* Transfer data (if any) from Write Queue -> UART. */
918 neo_copy_data_from_queue_to_uart(ch);
919 }
920}
921
922/*
923 * neo_param()
924 * Send any/all changes to the line to the UART.
925 */
926static void neo_param(struct jsm_channel *ch)
927{
928 u8 lcr = 0;
929 u8 uart_lcr, ier;
930 u32 baud;
931 int quot;
932 struct jsm_board *bd;
933
934 bd = ch->ch_bd;
935 if (!bd)
936 return;
937
938 /*
939 * If baud rate is zero, flush queues, and set mval to drop DTR.
940 */
941 if ((ch->ch_c_cflag & CBAUD) == B0) {
942 ch->ch_r_head = ch->ch_r_tail = 0;
943 ch->ch_e_head = ch->ch_e_tail = 0;
944
945 neo_flush_uart_write(ch);
946 neo_flush_uart_read(ch);
947
948 ch->ch_flags |= (CH_BAUD0);
949 ch->ch_mostat &= ~(UART_MCR_RTS | UART_MCR_DTR);
950 neo_assert_modem_signals(ch);
951 return;
952
953 } else {
954 int i;
955 unsigned int cflag;
956 static struct {
957 unsigned int rate;
958 unsigned int cflag;
959 } baud_rates[] = {
960 { 921600, B921600 },
961 { 460800, B460800 },
962 { 230400, B230400 },
963 { 115200, B115200 },
964 { 57600, B57600 },
965 { 38400, B38400 },
966 { 19200, B19200 },
967 { 9600, B9600 },
968 { 4800, B4800 },
969 { 2400, B2400 },
970 { 1200, B1200 },
971 { 600, B600 },
972 { 300, B300 },
973 { 200, B200 },
974 { 150, B150 },
975 { 134, B134 },
976 { 110, B110 },
977 { 75, B75 },
978 { 50, B50 },
979 };
980
981 cflag = C_BAUD(ch->uart_port.state->port.tty);
982 baud = 9600;
983 for (i = 0; i < ARRAY_SIZE(baud_rates); i++) {
984 if (baud_rates[i].cflag == cflag) {
985 baud = baud_rates[i].rate;
986 break;
987 }
988 }
989
990 if (ch->ch_flags & CH_BAUD0)
991 ch->ch_flags &= ~(CH_BAUD0);
992 }
993
994 if (ch->ch_c_cflag & PARENB)
995 lcr |= UART_LCR_PARITY;
996
997 if (!(ch->ch_c_cflag & PARODD))
998 lcr |= UART_LCR_EPAR;
999
1000 if (ch->ch_c_cflag & CMSPAR)
1001 lcr |= UART_LCR_SPAR;
1002
1003 if (ch->ch_c_cflag & CSTOPB)
1004 lcr |= UART_LCR_STOP;
1005
1006 lcr |= UART_LCR_WLEN(tty_get_char_size(ch->ch_c_cflag));
1007
1008 ier = readb(&ch->ch_neo_uart->ier);
1009 uart_lcr = readb(&ch->ch_neo_uart->lcr);
1010
1011 quot = ch->ch_bd->bd_dividend / baud;
1012
1013 if (quot != 0) {
1014 writeb(UART_LCR_DLAB, &ch->ch_neo_uart->lcr);
1015 writeb((quot & 0xff), &ch->ch_neo_uart->txrx);
1016 writeb((quot >> 8), &ch->ch_neo_uart->ier);
1017 writeb(lcr, &ch->ch_neo_uart->lcr);
1018 }
1019
1020 if (uart_lcr != lcr)
1021 writeb(lcr, &ch->ch_neo_uart->lcr);
1022
1023 if (ch->ch_c_cflag & CREAD)
1024 ier |= (UART_IER_RDI | UART_IER_RLSI);
1025
1026 ier |= (UART_IER_THRI | UART_IER_MSI);
1027
1028 writeb(ier, &ch->ch_neo_uart->ier);
1029
1030 /* Set new start/stop chars */
1031 neo_set_new_start_stop_chars(ch);
1032
1033 if (ch->ch_c_cflag & CRTSCTS)
1034 neo_set_cts_flow_control(ch);
1035 else if (ch->ch_c_iflag & IXON) {
1036 /* If start/stop is set to disable, then we should disable flow control */
1037 if ((ch->ch_startc == __DISABLED_CHAR) || (ch->ch_stopc == __DISABLED_CHAR))
1038 neo_set_no_output_flow_control(ch);
1039 else
1040 neo_set_ixon_flow_control(ch);
1041 }
1042 else
1043 neo_set_no_output_flow_control(ch);
1044
1045 if (ch->ch_c_cflag & CRTSCTS)
1046 neo_set_rts_flow_control(ch);
1047 else if (ch->ch_c_iflag & IXOFF) {
1048 /* If start/stop is set to disable, then we should disable flow control */
1049 if ((ch->ch_startc == __DISABLED_CHAR) || (ch->ch_stopc == __DISABLED_CHAR))
1050 neo_set_no_input_flow_control(ch);
1051 else
1052 neo_set_ixoff_flow_control(ch);
1053 }
1054 else
1055 neo_set_no_input_flow_control(ch);
1056 /*
1057 * Adjust the RX FIFO Trigger level if baud is less than 9600.
1058 * Not exactly elegant, but this is needed because of the Exar chip's
1059 * delay on firing off the RX FIFO interrupt on slower baud rates.
1060 */
1061 if (baud < 9600) {
1062 writeb(1, &ch->ch_neo_uart->rfifo);
1063 ch->ch_r_tlevel = 1;
1064 }
1065
1066 neo_assert_modem_signals(ch);
1067
1068 /* Get current status of the modem signals now */
1069 neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr));
1070 return;
1071}
1072
1073/*
1074 * jsm_neo_intr()
1075 *
1076 * Neo specific interrupt handler.
1077 */
1078static irqreturn_t neo_intr(int irq, void *voidbrd)
1079{
1080 struct jsm_board *brd = voidbrd;
1081 struct jsm_channel *ch;
1082 int port = 0;
1083 int type = 0;
1084 int current_port;
1085 u32 tmp;
1086 u32 uart_poll;
1087 unsigned long lock_flags;
1088 unsigned long lock_flags2;
1089 int outofloop_count = 0;
1090
1091 /* Lock out the slow poller from running on this board. */
1092 spin_lock_irqsave(&brd->bd_intr_lock, lock_flags);
1093
1094 /*
1095 * Read in "extended" IRQ information from the 32bit Neo register.
1096 * Bits 0-7: What port triggered the interrupt.
1097 * Bits 8-31: Each 3bits indicate what type of interrupt occurred.
1098 */
1099 uart_poll = readl(brd->re_map_membase + UART_17158_POLL_ADDR_OFFSET);
1100
1101 jsm_dbg(INTR, &brd->pci_dev, "%s:%d uart_poll: %x\n",
1102 __FILE__, __LINE__, uart_poll);
1103
1104 if (!uart_poll) {
1105 jsm_dbg(INTR, &brd->pci_dev,
1106 "Kernel interrupted to me, but no pending interrupts...\n");
1107 spin_unlock_irqrestore(&brd->bd_intr_lock, lock_flags);
1108 return IRQ_NONE;
1109 }
1110
1111 /* At this point, we have at least SOMETHING to service, dig further... */
1112
1113 current_port = 0;
1114
1115 /* Loop on each port */
1116 while (((uart_poll & 0xff) != 0) && (outofloop_count < 0xff)){
1117
1118 tmp = uart_poll;
1119 outofloop_count++;
1120
1121 /* Check current port to see if it has interrupt pending */
1122 if ((tmp & jsm_offset_table[current_port]) != 0) {
1123 port = current_port;
1124 type = tmp >> (8 + (port * 3));
1125 type &= 0x7;
1126 } else {
1127 current_port++;
1128 continue;
1129 }
1130
1131 jsm_dbg(INTR, &brd->pci_dev, "%s:%d port: %x type: %x\n",
1132 __FILE__, __LINE__, port, type);
1133
1134 /* Remove this port + type from uart_poll */
1135 uart_poll &= ~(jsm_offset_table[port]);
1136
1137 if (!type) {
1138 /* If no type, just ignore it, and move onto next port */
1139 jsm_dbg(INTR, &brd->pci_dev,
1140 "Interrupt with no type! port: %d\n", port);
1141 continue;
1142 }
1143
1144 /* Switch on type of interrupt we have */
1145 switch (type) {
1146
1147 case UART_17158_RXRDY_TIMEOUT:
1148 /*
1149 * RXRDY Time-out is cleared by reading data in the
1150 * RX FIFO until it falls below the trigger level.
1151 */
1152
1153 /* Verify the port is in range. */
1154 if (port >= brd->nasync)
1155 continue;
1156
1157 ch = brd->channels[port];
1158 if (!ch)
1159 continue;
1160
1161 neo_copy_data_from_uart_to_queue(ch);
1162
1163 /* Call our tty layer to enforce queue flow control if needed. */
1164 spin_lock_irqsave(&ch->ch_lock, lock_flags2);
1165 jsm_check_queue_flow_control(ch);
1166 spin_unlock_irqrestore(&ch->ch_lock, lock_flags2);
1167
1168 continue;
1169
1170 case UART_17158_RX_LINE_STATUS:
1171 /*
1172 * RXRDY and RX LINE Status (logic OR of LSR[4:1])
1173 */
1174 neo_parse_lsr(brd, port);
1175 continue;
1176
1177 case UART_17158_TXRDY:
1178 /*
1179 * TXRDY interrupt clears after reading ISR register for the UART channel.
1180 */
1181
1182 /*
1183 * Yes, this is odd...
1184 * Why would I check EVERY possibility of type of
1185 * interrupt, when we know its TXRDY???
1186 * Becuz for some reason, even tho we got triggered for TXRDY,
1187 * it seems to be occasionally wrong. Instead of TX, which
1188 * it should be, I was getting things like RXDY too. Weird.
1189 */
1190 neo_parse_isr(brd, port);
1191 continue;
1192
1193 case UART_17158_MSR:
1194 /*
1195 * MSR or flow control was seen.
1196 */
1197 neo_parse_isr(brd, port);
1198 continue;
1199
1200 default:
1201 /*
1202 * The UART triggered us with a bogus interrupt type.
1203 * It appears the Exar chip, when REALLY bogged down, will throw
1204 * these once and awhile.
1205 * Its harmless, just ignore it and move on.
1206 */
1207 jsm_dbg(INTR, &brd->pci_dev,
1208 "%s:%d Unknown Interrupt type: %x\n",
1209 __FILE__, __LINE__, type);
1210 continue;
1211 }
1212 }
1213
1214 spin_unlock_irqrestore(&brd->bd_intr_lock, lock_flags);
1215
1216 jsm_dbg(INTR, &brd->pci_dev, "finish\n");
1217 return IRQ_HANDLED;
1218}
1219
1220/*
1221 * Neo specific way of turning off the receiver.
1222 * Used as a way to enforce queue flow control when in
1223 * hardware flow control mode.
1224 */
1225static void neo_disable_receiver(struct jsm_channel *ch)
1226{
1227 u8 tmp = readb(&ch->ch_neo_uart->ier);
1228 tmp &= ~(UART_IER_RDI);
1229 writeb(tmp, &ch->ch_neo_uart->ier);
1230
1231 /* flush write operation */
1232 neo_pci_posting_flush(ch->ch_bd);
1233}
1234
1235
1236/*
1237 * Neo specific way of turning on the receiver.
1238 * Used as a way to un-enforce queue flow control when in
1239 * hardware flow control mode.
1240 */
1241static void neo_enable_receiver(struct jsm_channel *ch)
1242{
1243 u8 tmp = readb(&ch->ch_neo_uart->ier);
1244 tmp |= (UART_IER_RDI);
1245 writeb(tmp, &ch->ch_neo_uart->ier);
1246
1247 /* flush write operation */
1248 neo_pci_posting_flush(ch->ch_bd);
1249}
1250
1251static void neo_send_start_character(struct jsm_channel *ch)
1252{
1253 if (!ch)
1254 return;
1255
1256 if (ch->ch_startc != __DISABLED_CHAR) {
1257 ch->ch_xon_sends++;
1258 writeb(ch->ch_startc, &ch->ch_neo_uart->txrx);
1259
1260 /* flush write operation */
1261 neo_pci_posting_flush(ch->ch_bd);
1262 }
1263}
1264
1265static void neo_send_stop_character(struct jsm_channel *ch)
1266{
1267 if (!ch)
1268 return;
1269
1270 if (ch->ch_stopc != __DISABLED_CHAR) {
1271 ch->ch_xoff_sends++;
1272 writeb(ch->ch_stopc, &ch->ch_neo_uart->txrx);
1273
1274 /* flush write operation */
1275 neo_pci_posting_flush(ch->ch_bd);
1276 }
1277}
1278
1279/*
1280 * neo_uart_init
1281 */
1282static void neo_uart_init(struct jsm_channel *ch)
1283{
1284 writeb(0, &ch->ch_neo_uart->ier);
1285 writeb(0, &ch->ch_neo_uart->efr);
1286 writeb(UART_EFR_ECB, &ch->ch_neo_uart->efr);
1287
1288 /* Clear out UART and FIFO */
1289 readb(&ch->ch_neo_uart->txrx);
1290 writeb((UART_FCR_ENABLE_FIFO|UART_FCR_CLEAR_RCVR|UART_FCR_CLEAR_XMIT), &ch->ch_neo_uart->isr_fcr);
1291 readb(&ch->ch_neo_uart->lsr);
1292 readb(&ch->ch_neo_uart->msr);
1293
1294 ch->ch_flags |= CH_FIFO_ENABLED;
1295
1296 /* Assert any signals we want up */
1297 writeb(ch->ch_mostat, &ch->ch_neo_uart->mcr);
1298}
1299
1300/*
1301 * Make the UART completely turn off.
1302 */
1303static void neo_uart_off(struct jsm_channel *ch)
1304{
1305 /* Turn off UART enhanced bits */
1306 writeb(0, &ch->ch_neo_uart->efr);
1307
1308 /* Stop all interrupts from occurring. */
1309 writeb(0, &ch->ch_neo_uart->ier);
1310}
1311
1312/* Channel lock MUST be held by the calling function! */
1313static void neo_send_break(struct jsm_channel *ch)
1314{
1315 /*
1316 * Set the time we should stop sending the break.
1317 * If we are already sending a break, toss away the existing
1318 * time to stop, and use this new value instead.
1319 */
1320
1321 /* Tell the UART to start sending the break */
1322 if (!(ch->ch_flags & CH_BREAK_SENDING)) {
1323 u8 temp = readb(&ch->ch_neo_uart->lcr);
1324 writeb((temp | UART_LCR_SBC), &ch->ch_neo_uart->lcr);
1325 ch->ch_flags |= (CH_BREAK_SENDING);
1326
1327 /* flush write operation */
1328 neo_pci_posting_flush(ch->ch_bd);
1329 }
1330}
1331
1332struct board_ops jsm_neo_ops = {
1333 .intr = neo_intr,
1334 .uart_init = neo_uart_init,
1335 .uart_off = neo_uart_off,
1336 .param = neo_param,
1337 .assert_modem_signals = neo_assert_modem_signals,
1338 .flush_uart_write = neo_flush_uart_write,
1339 .flush_uart_read = neo_flush_uart_read,
1340 .disable_receiver = neo_disable_receiver,
1341 .enable_receiver = neo_enable_receiver,
1342 .send_break = neo_send_break,
1343 .clear_break = neo_clear_break,
1344 .send_start_character = neo_send_start_character,
1345 .send_stop_character = neo_send_stop_character,
1346 .copy_data_from_queue_to_uart = neo_copy_data_from_queue_to_uart,
1347};
1/************************************************************************
2 * Copyright 2003 Digi International (www.digi.com)
3 *
4 * Copyright (C) 2004 IBM Corporation. All rights reserved.
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2, or (at your option)
9 * any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the
13 * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
14 * PURPOSE. See the GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 * Temple Place - Suite 330, Boston,
19 * MA 02111-1307, USA.
20 *
21 * Contact Information:
22 * Scott H Kilau <Scott_Kilau@digi.com>
23 * Wendy Xiong <wendyx@us.ibm.com>
24 *
25 ***********************************************************************/
26#include <linux/delay.h> /* For udelay */
27#include <linux/serial_reg.h> /* For the various UART offsets */
28#include <linux/tty.h>
29#include <linux/pci.h>
30#include <asm/io.h>
31
32#include "jsm.h" /* Driver main header file */
33
34static u32 jsm_offset_table[8] = { 0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80 };
35
36/*
37 * This function allows calls to ensure that all outstanding
38 * PCI writes have been completed, by doing a PCI read against
39 * a non-destructive, read-only location on the Neo card.
40 *
41 * In this case, we are reading the DVID (Read-only Device Identification)
42 * value of the Neo card.
43 */
44static inline void neo_pci_posting_flush(struct jsm_board *bd)
45{
46 readb(bd->re_map_membase + 0x8D);
47}
48
49static void neo_set_cts_flow_control(struct jsm_channel *ch)
50{
51 u8 ier, efr;
52 ier = readb(&ch->ch_neo_uart->ier);
53 efr = readb(&ch->ch_neo_uart->efr);
54
55 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting CTSFLOW\n");
56
57 /* Turn on auto CTS flow control */
58 ier |= (UART_17158_IER_CTSDSR);
59 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_CTSDSR);
60
61 /* Turn off auto Xon flow control */
62 efr &= ~(UART_17158_EFR_IXON);
63
64 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
65 writeb(0, &ch->ch_neo_uart->efr);
66
67 /* Turn on UART enhanced bits */
68 writeb(efr, &ch->ch_neo_uart->efr);
69
70 /* Turn on table D, with 8 char hi/low watermarks */
71 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY), &ch->ch_neo_uart->fctr);
72
73 /* Feed the UART our trigger levels */
74 writeb(8, &ch->ch_neo_uart->tfifo);
75 ch->ch_t_tlevel = 8;
76
77 writeb(ier, &ch->ch_neo_uart->ier);
78}
79
80static void neo_set_rts_flow_control(struct jsm_channel *ch)
81{
82 u8 ier, efr;
83 ier = readb(&ch->ch_neo_uart->ier);
84 efr = readb(&ch->ch_neo_uart->efr);
85
86 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting RTSFLOW\n");
87
88 /* Turn on auto RTS flow control */
89 ier |= (UART_17158_IER_RTSDTR);
90 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_RTSDTR);
91
92 /* Turn off auto Xoff flow control */
93 ier &= ~(UART_17158_IER_XOFF);
94 efr &= ~(UART_17158_EFR_IXOFF);
95
96 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
97 writeb(0, &ch->ch_neo_uart->efr);
98
99 /* Turn on UART enhanced bits */
100 writeb(efr, &ch->ch_neo_uart->efr);
101
102 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY), &ch->ch_neo_uart->fctr);
103 ch->ch_r_watermark = 4;
104
105 writeb(56, &ch->ch_neo_uart->rfifo);
106 ch->ch_r_tlevel = 56;
107
108 writeb(ier, &ch->ch_neo_uart->ier);
109
110 /*
111 * From the Neo UART spec sheet:
112 * The auto RTS/DTR function must be started by asserting
113 * RTS/DTR# output pin (MCR bit-0 or 1 to logic 1 after
114 * it is enabled.
115 */
116 ch->ch_mostat |= (UART_MCR_RTS);
117}
118
119
120static void neo_set_ixon_flow_control(struct jsm_channel *ch)
121{
122 u8 ier, efr;
123 ier = readb(&ch->ch_neo_uart->ier);
124 efr = readb(&ch->ch_neo_uart->efr);
125
126 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting IXON FLOW\n");
127
128 /* Turn off auto CTS flow control */
129 ier &= ~(UART_17158_IER_CTSDSR);
130 efr &= ~(UART_17158_EFR_CTSDSR);
131
132 /* Turn on auto Xon flow control */
133 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXON);
134
135 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
136 writeb(0, &ch->ch_neo_uart->efr);
137
138 /* Turn on UART enhanced bits */
139 writeb(efr, &ch->ch_neo_uart->efr);
140
141 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
142 ch->ch_r_watermark = 4;
143
144 writeb(32, &ch->ch_neo_uart->rfifo);
145 ch->ch_r_tlevel = 32;
146
147 /* Tell UART what start/stop chars it should be looking for */
148 writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
149 writeb(0, &ch->ch_neo_uart->xonchar2);
150
151 writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1);
152 writeb(0, &ch->ch_neo_uart->xoffchar2);
153
154 writeb(ier, &ch->ch_neo_uart->ier);
155}
156
157static void neo_set_ixoff_flow_control(struct jsm_channel *ch)
158{
159 u8 ier, efr;
160 ier = readb(&ch->ch_neo_uart->ier);
161 efr = readb(&ch->ch_neo_uart->efr);
162
163 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting IXOFF FLOW\n");
164
165 /* Turn off auto RTS flow control */
166 ier &= ~(UART_17158_IER_RTSDTR);
167 efr &= ~(UART_17158_EFR_RTSDTR);
168
169 /* Turn on auto Xoff flow control */
170 ier |= (UART_17158_IER_XOFF);
171 efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXOFF);
172
173 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
174 writeb(0, &ch->ch_neo_uart->efr);
175
176 /* Turn on UART enhanced bits */
177 writeb(efr, &ch->ch_neo_uart->efr);
178
179 /* Turn on table D, with 8 char hi/low watermarks */
180 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
181
182 writeb(8, &ch->ch_neo_uart->tfifo);
183 ch->ch_t_tlevel = 8;
184
185 /* Tell UART what start/stop chars it should be looking for */
186 writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
187 writeb(0, &ch->ch_neo_uart->xonchar2);
188
189 writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1);
190 writeb(0, &ch->ch_neo_uart->xoffchar2);
191
192 writeb(ier, &ch->ch_neo_uart->ier);
193}
194
195static void neo_set_no_input_flow_control(struct jsm_channel *ch)
196{
197 u8 ier, efr;
198 ier = readb(&ch->ch_neo_uart->ier);
199 efr = readb(&ch->ch_neo_uart->efr);
200
201 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Unsetting Input FLOW\n");
202
203 /* Turn off auto RTS flow control */
204 ier &= ~(UART_17158_IER_RTSDTR);
205 efr &= ~(UART_17158_EFR_RTSDTR);
206
207 /* Turn off auto Xoff flow control */
208 ier &= ~(UART_17158_IER_XOFF);
209 if (ch->ch_c_iflag & IXON)
210 efr &= ~(UART_17158_EFR_IXOFF);
211 else
212 efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXOFF);
213
214 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
215 writeb(0, &ch->ch_neo_uart->efr);
216
217 /* Turn on UART enhanced bits */
218 writeb(efr, &ch->ch_neo_uart->efr);
219
220 /* Turn on table D, with 8 char hi/low watermarks */
221 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
222
223 ch->ch_r_watermark = 0;
224
225 writeb(16, &ch->ch_neo_uart->tfifo);
226 ch->ch_t_tlevel = 16;
227
228 writeb(16, &ch->ch_neo_uart->rfifo);
229 ch->ch_r_tlevel = 16;
230
231 writeb(ier, &ch->ch_neo_uart->ier);
232}
233
234static void neo_set_no_output_flow_control(struct jsm_channel *ch)
235{
236 u8 ier, efr;
237 ier = readb(&ch->ch_neo_uart->ier);
238 efr = readb(&ch->ch_neo_uart->efr);
239
240 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Unsetting Output FLOW\n");
241
242 /* Turn off auto CTS flow control */
243 ier &= ~(UART_17158_IER_CTSDSR);
244 efr &= ~(UART_17158_EFR_CTSDSR);
245
246 /* Turn off auto Xon flow control */
247 if (ch->ch_c_iflag & IXOFF)
248 efr &= ~(UART_17158_EFR_IXON);
249 else
250 efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXON);
251
252 /* Why? Becuz Exar's spec says we have to zero it out before setting it */
253 writeb(0, &ch->ch_neo_uart->efr);
254
255 /* Turn on UART enhanced bits */
256 writeb(efr, &ch->ch_neo_uart->efr);
257
258 /* Turn on table D, with 8 char hi/low watermarks */
259 writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
260
261 ch->ch_r_watermark = 0;
262
263 writeb(16, &ch->ch_neo_uart->tfifo);
264 ch->ch_t_tlevel = 16;
265
266 writeb(16, &ch->ch_neo_uart->rfifo);
267 ch->ch_r_tlevel = 16;
268
269 writeb(ier, &ch->ch_neo_uart->ier);
270}
271
272static inline void neo_set_new_start_stop_chars(struct jsm_channel *ch)
273{
274
275 /* if hardware flow control is set, then skip this whole thing */
276 if (ch->ch_c_cflag & CRTSCTS)
277 return;
278
279 jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "start\n");
280
281 /* Tell UART what start/stop chars it should be looking for */
282 writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
283 writeb(0, &ch->ch_neo_uart->xonchar2);
284
285 writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1);
286 writeb(0, &ch->ch_neo_uart->xoffchar2);
287}
288
289static void neo_copy_data_from_uart_to_queue(struct jsm_channel *ch)
290{
291 int qleft = 0;
292 u8 linestatus = 0;
293 u8 error_mask = 0;
294 int n = 0;
295 int total = 0;
296 u16 head;
297 u16 tail;
298
299 if (!ch)
300 return;
301
302 /* cache head and tail of queue */
303 head = ch->ch_r_head & RQUEUEMASK;
304 tail = ch->ch_r_tail & RQUEUEMASK;
305
306 /* Get our cached LSR */
307 linestatus = ch->ch_cached_lsr;
308 ch->ch_cached_lsr = 0;
309
310 /* Store how much space we have left in the queue */
311 if ((qleft = tail - head - 1) < 0)
312 qleft += RQUEUEMASK + 1;
313
314 /*
315 * If the UART is not in FIFO mode, force the FIFO copy to
316 * NOT be run, by setting total to 0.
317 *
318 * On the other hand, if the UART IS in FIFO mode, then ask
319 * the UART to give us an approximation of data it has RX'ed.
320 */
321 if (!(ch->ch_flags & CH_FIFO_ENABLED))
322 total = 0;
323 else {
324 total = readb(&ch->ch_neo_uart->rfifo);
325
326 /*
327 * EXAR chip bug - RX FIFO COUNT - Fudge factor.
328 *
329 * This resolves a problem/bug with the Exar chip that sometimes
330 * returns a bogus value in the rfifo register.
331 * The count can be any where from 0-3 bytes "off".
332 * Bizarre, but true.
333 */
334 total -= 3;
335 }
336
337 /*
338 * Finally, bound the copy to make sure we don't overflow
339 * our own queue...
340 * The byte by byte copy loop below this loop this will
341 * deal with the queue overflow possibility.
342 */
343 total = min(total, qleft);
344
345 while (total > 0) {
346 /*
347 * Grab the linestatus register, we need to check
348 * to see if there are any errors in the FIFO.
349 */
350 linestatus = readb(&ch->ch_neo_uart->lsr);
351
352 /*
353 * Break out if there is a FIFO error somewhere.
354 * This will allow us to go byte by byte down below,
355 * finding the exact location of the error.
356 */
357 if (linestatus & UART_17158_RX_FIFO_DATA_ERROR)
358 break;
359
360 /* Make sure we don't go over the end of our queue */
361 n = min(((u32) total), (RQUEUESIZE - (u32) head));
362
363 /*
364 * Cut down n even further if needed, this is to fix
365 * a problem with memcpy_fromio() with the Neo on the
366 * IBM pSeries platform.
367 * 15 bytes max appears to be the magic number.
368 */
369 n = min((u32) n, (u32) 12);
370
371 /*
372 * Since we are grabbing the linestatus register, which
373 * will reset some bits after our read, we need to ensure
374 * we don't miss our TX FIFO emptys.
375 */
376 if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR))
377 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
378
379 linestatus = 0;
380
381 /* Copy data from uart to the queue */
382 memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, n);
383 /*
384 * Since RX_FIFO_DATA_ERROR was 0, we are guaranteed
385 * that all the data currently in the FIFO is free of
386 * breaks and parity/frame/orun errors.
387 */
388 memset(ch->ch_equeue + head, 0, n);
389
390 /* Add to and flip head if needed */
391 head = (head + n) & RQUEUEMASK;
392 total -= n;
393 qleft -= n;
394 ch->ch_rxcount += n;
395 }
396
397 /*
398 * Create a mask to determine whether we should
399 * insert the character (if any) into our queue.
400 */
401 if (ch->ch_c_iflag & IGNBRK)
402 error_mask |= UART_LSR_BI;
403
404 /*
405 * Now cleanup any leftover bytes still in the UART.
406 * Also deal with any possible queue overflow here as well.
407 */
408 while (1) {
409
410 /*
411 * Its possible we have a linestatus from the loop above
412 * this, so we "OR" on any extra bits.
413 */
414 linestatus |= readb(&ch->ch_neo_uart->lsr);
415
416 /*
417 * If the chip tells us there is no more data pending to
418 * be read, we can then leave.
419 * But before we do, cache the linestatus, just in case.
420 */
421 if (!(linestatus & UART_LSR_DR)) {
422 ch->ch_cached_lsr = linestatus;
423 break;
424 }
425
426 /* No need to store this bit */
427 linestatus &= ~UART_LSR_DR;
428
429 /*
430 * Since we are grabbing the linestatus register, which
431 * will reset some bits after our read, we need to ensure
432 * we don't miss our TX FIFO emptys.
433 */
434 if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR)) {
435 linestatus &= ~(UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR);
436 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
437 }
438
439 /*
440 * Discard character if we are ignoring the error mask.
441 */
442 if (linestatus & error_mask) {
443 u8 discard;
444 linestatus = 0;
445 memcpy_fromio(&discard, &ch->ch_neo_uart->txrxburst, 1);
446 continue;
447 }
448
449 /*
450 * If our queue is full, we have no choice but to drop some data.
451 * The assumption is that HWFLOW or SWFLOW should have stopped
452 * things way way before we got to this point.
453 *
454 * I decided that I wanted to ditch the oldest data first,
455 * I hope thats okay with everyone? Yes? Good.
456 */
457 while (qleft < 1) {
458 jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
459 "Queue full, dropping DATA:%x LSR:%x\n",
460 ch->ch_rqueue[tail], ch->ch_equeue[tail]);
461
462 ch->ch_r_tail = tail = (tail + 1) & RQUEUEMASK;
463 ch->ch_err_overrun++;
464 qleft++;
465 }
466
467 memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, 1);
468 ch->ch_equeue[head] = (u8) linestatus;
469
470 jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
471 "DATA/LSR pair: %x %x\n", ch->ch_rqueue[head], ch->ch_equeue[head]);
472
473 /* Ditch any remaining linestatus value. */
474 linestatus = 0;
475
476 /* Add to and flip head if needed */
477 head = (head + 1) & RQUEUEMASK;
478
479 qleft--;
480 ch->ch_rxcount++;
481 }
482
483 /*
484 * Write new final heads to channel structure.
485 */
486 ch->ch_r_head = head & RQUEUEMASK;
487 ch->ch_e_head = head & EQUEUEMASK;
488 jsm_input(ch);
489}
490
491static void neo_copy_data_from_queue_to_uart(struct jsm_channel *ch)
492{
493 u16 head;
494 u16 tail;
495 int n;
496 int s;
497 int qlen;
498 u32 len_written = 0;
499 struct circ_buf *circ;
500
501 if (!ch)
502 return;
503
504 circ = &ch->uart_port.state->xmit;
505
506 /* No data to write to the UART */
507 if (uart_circ_empty(circ))
508 return;
509
510 /* If port is "stopped", don't send any data to the UART */
511 if ((ch->ch_flags & CH_STOP) || (ch->ch_flags & CH_BREAK_SENDING))
512 return;
513 /*
514 * If FIFOs are disabled. Send data directly to txrx register
515 */
516 if (!(ch->ch_flags & CH_FIFO_ENABLED)) {
517 u8 lsrbits = readb(&ch->ch_neo_uart->lsr);
518
519 ch->ch_cached_lsr |= lsrbits;
520 if (ch->ch_cached_lsr & UART_LSR_THRE) {
521 ch->ch_cached_lsr &= ~(UART_LSR_THRE);
522
523 writeb(circ->buf[circ->tail], &ch->ch_neo_uart->txrx);
524 jsm_printk(WRITE, INFO, &ch->ch_bd->pci_dev,
525 "Tx data: %x\n", circ->buf[circ->tail]);
526 circ->tail = (circ->tail + 1) & (UART_XMIT_SIZE - 1);
527 ch->ch_txcount++;
528 }
529 return;
530 }
531
532 /*
533 * We have to do it this way, because of the EXAR TXFIFO count bug.
534 */
535 if (!(ch->ch_flags & (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM)))
536 return;
537
538 n = UART_17158_TX_FIFOSIZE - ch->ch_t_tlevel;
539
540 /* cache head and tail of queue */
541 head = circ->head & (UART_XMIT_SIZE - 1);
542 tail = circ->tail & (UART_XMIT_SIZE - 1);
543 qlen = uart_circ_chars_pending(circ);
544
545 /* Find minimum of the FIFO space, versus queue length */
546 n = min(n, qlen);
547
548 while (n > 0) {
549
550 s = ((head >= tail) ? head : UART_XMIT_SIZE) - tail;
551 s = min(s, n);
552
553 if (s <= 0)
554 break;
555
556 memcpy_toio(&ch->ch_neo_uart->txrxburst, circ->buf + tail, s);
557 /* Add and flip queue if needed */
558 tail = (tail + s) & (UART_XMIT_SIZE - 1);
559 n -= s;
560 ch->ch_txcount += s;
561 len_written += s;
562 }
563
564 /* Update the final tail */
565 circ->tail = tail & (UART_XMIT_SIZE - 1);
566
567 if (len_written >= ch->ch_t_tlevel)
568 ch->ch_flags &= ~(CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
569
570 if (uart_circ_empty(circ))
571 uart_write_wakeup(&ch->uart_port);
572}
573
574static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
575{
576 u8 msignals = signals;
577
578 jsm_printk(MSIGS, INFO, &ch->ch_bd->pci_dev,
579 "neo_parse_modem: port: %d msignals: %x\n", ch->ch_portnum, msignals);
580
581 /* Scrub off lower bits. They signify delta's, which I don't care about */
582 /* Keep DDCD and DDSR though */
583 msignals &= 0xf8;
584
585 if (msignals & UART_MSR_DDCD)
586 uart_handle_dcd_change(&ch->uart_port, msignals & UART_MSR_DCD);
587 if (msignals & UART_MSR_DDSR)
588 uart_handle_cts_change(&ch->uart_port, msignals & UART_MSR_CTS);
589 if (msignals & UART_MSR_DCD)
590 ch->ch_mistat |= UART_MSR_DCD;
591 else
592 ch->ch_mistat &= ~UART_MSR_DCD;
593
594 if (msignals & UART_MSR_DSR)
595 ch->ch_mistat |= UART_MSR_DSR;
596 else
597 ch->ch_mistat &= ~UART_MSR_DSR;
598
599 if (msignals & UART_MSR_RI)
600 ch->ch_mistat |= UART_MSR_RI;
601 else
602 ch->ch_mistat &= ~UART_MSR_RI;
603
604 if (msignals & UART_MSR_CTS)
605 ch->ch_mistat |= UART_MSR_CTS;
606 else
607 ch->ch_mistat &= ~UART_MSR_CTS;
608
609 jsm_printk(MSIGS, INFO, &ch->ch_bd->pci_dev,
610 "Port: %d DTR: %d RTS: %d CTS: %d DSR: %d " "RI: %d CD: %d\n",
611 ch->ch_portnum,
612 !!((ch->ch_mistat | ch->ch_mostat) & UART_MCR_DTR),
613 !!((ch->ch_mistat | ch->ch_mostat) & UART_MCR_RTS),
614 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_CTS),
615 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_DSR),
616 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_RI),
617 !!((ch->ch_mistat | ch->ch_mostat) & UART_MSR_DCD));
618}
619
620/* Make the UART raise any of the output signals we want up */
621static void neo_assert_modem_signals(struct jsm_channel *ch)
622{
623 if (!ch)
624 return;
625
626 writeb(ch->ch_mostat, &ch->ch_neo_uart->mcr);
627
628 /* flush write operation */
629 neo_pci_posting_flush(ch->ch_bd);
630}
631
632/*
633 * Flush the WRITE FIFO on the Neo.
634 *
635 * NOTE: Channel lock MUST be held before calling this function!
636 */
637static void neo_flush_uart_write(struct jsm_channel *ch)
638{
639 u8 tmp = 0;
640 int i = 0;
641
642 if (!ch)
643 return;
644
645 writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_XMIT), &ch->ch_neo_uart->isr_fcr);
646
647 for (i = 0; i < 10; i++) {
648
649 /* Check to see if the UART feels it completely flushed the FIFO. */
650 tmp = readb(&ch->ch_neo_uart->isr_fcr);
651 if (tmp & 4) {
652 jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev,
653 "Still flushing TX UART... i: %d\n", i);
654 udelay(10);
655 }
656 else
657 break;
658 }
659
660 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
661}
662
663
664/*
665 * Flush the READ FIFO on the Neo.
666 *
667 * NOTE: Channel lock MUST be held before calling this function!
668 */
669static void neo_flush_uart_read(struct jsm_channel *ch)
670{
671 u8 tmp = 0;
672 int i = 0;
673
674 if (!ch)
675 return;
676
677 writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR), &ch->ch_neo_uart->isr_fcr);
678
679 for (i = 0; i < 10; i++) {
680
681 /* Check to see if the UART feels it completely flushed the FIFO. */
682 tmp = readb(&ch->ch_neo_uart->isr_fcr);
683 if (tmp & 2) {
684 jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev,
685 "Still flushing RX UART... i: %d\n", i);
686 udelay(10);
687 }
688 else
689 break;
690 }
691}
692
693/*
694 * No locks are assumed to be held when calling this function.
695 */
696static void neo_clear_break(struct jsm_channel *ch, int force)
697{
698 unsigned long lock_flags;
699
700 spin_lock_irqsave(&ch->ch_lock, lock_flags);
701
702 /* Turn break off, and unset some variables */
703 if (ch->ch_flags & CH_BREAK_SENDING) {
704 u8 temp = readb(&ch->ch_neo_uart->lcr);
705 writeb((temp & ~UART_LCR_SBC), &ch->ch_neo_uart->lcr);
706
707 ch->ch_flags &= ~(CH_BREAK_SENDING);
708 jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev,
709 "clear break Finishing UART_LCR_SBC! finished: %lx\n", jiffies);
710
711 /* flush write operation */
712 neo_pci_posting_flush(ch->ch_bd);
713 }
714 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
715}
716
717/*
718 * Parse the ISR register.
719 */
720static inline void neo_parse_isr(struct jsm_board *brd, u32 port)
721{
722 struct jsm_channel *ch;
723 u8 isr;
724 u8 cause;
725 unsigned long lock_flags;
726
727 if (!brd)
728 return;
729
730 if (port > brd->maxports)
731 return;
732
733 ch = brd->channels[port];
734 if (!ch)
735 return;
736
737 /* Here we try to figure out what caused the interrupt to happen */
738 while (1) {
739
740 isr = readb(&ch->ch_neo_uart->isr_fcr);
741
742 /* Bail if no pending interrupt */
743 if (isr & UART_IIR_NO_INT)
744 break;
745
746 /*
747 * Yank off the upper 2 bits, which just show that the FIFO's are enabled.
748 */
749 isr &= ~(UART_17158_IIR_FIFO_ENABLED);
750
751 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
752 "%s:%d isr: %x\n", __FILE__, __LINE__, isr);
753
754 if (isr & (UART_17158_IIR_RDI_TIMEOUT | UART_IIR_RDI)) {
755 /* Read data from uart -> queue */
756 neo_copy_data_from_uart_to_queue(ch);
757
758 /* Call our tty layer to enforce queue flow control if needed. */
759 spin_lock_irqsave(&ch->ch_lock, lock_flags);
760 jsm_check_queue_flow_control(ch);
761 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
762 }
763
764 if (isr & UART_IIR_THRI) {
765 /* Transfer data (if any) from Write Queue -> UART. */
766 spin_lock_irqsave(&ch->ch_lock, lock_flags);
767 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
768 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
769 neo_copy_data_from_queue_to_uart(ch);
770 }
771
772 if (isr & UART_17158_IIR_XONXOFF) {
773 cause = readb(&ch->ch_neo_uart->xoffchar1);
774
775 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
776 "Port %d. Got ISR_XONXOFF: cause:%x\n", port, cause);
777
778 /*
779 * Since the UART detected either an XON or
780 * XOFF match, we need to figure out which
781 * one it was, so we can suspend or resume data flow.
782 */
783 spin_lock_irqsave(&ch->ch_lock, lock_flags);
784 if (cause == UART_17158_XON_DETECT) {
785 /* Is output stopped right now, if so, resume it */
786 if (brd->channels[port]->ch_flags & CH_STOP) {
787 ch->ch_flags &= ~(CH_STOP);
788 }
789 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
790 "Port %d. XON detected in incoming data\n", port);
791 }
792 else if (cause == UART_17158_XOFF_DETECT) {
793 if (!(brd->channels[port]->ch_flags & CH_STOP)) {
794 ch->ch_flags |= CH_STOP;
795 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
796 "Setting CH_STOP\n");
797 }
798 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
799 "Port: %d. XOFF detected in incoming data\n", port);
800 }
801 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
802 }
803
804 if (isr & UART_17158_IIR_HWFLOW_STATE_CHANGE) {
805 /*
806 * If we get here, this means the hardware is doing auto flow control.
807 * Check to see whether RTS/DTR or CTS/DSR caused this interrupt.
808 */
809 cause = readb(&ch->ch_neo_uart->mcr);
810
811 /* Which pin is doing auto flow? RTS or DTR? */
812 spin_lock_irqsave(&ch->ch_lock, lock_flags);
813 if ((cause & 0x4) == 0) {
814 if (cause & UART_MCR_RTS)
815 ch->ch_mostat |= UART_MCR_RTS;
816 else
817 ch->ch_mostat &= ~(UART_MCR_RTS);
818 } else {
819 if (cause & UART_MCR_DTR)
820 ch->ch_mostat |= UART_MCR_DTR;
821 else
822 ch->ch_mostat &= ~(UART_MCR_DTR);
823 }
824 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
825 }
826
827 /* Parse any modem signal changes */
828 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
829 "MOD_STAT: sending to parse_modem_sigs\n");
830 neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr));
831 }
832}
833
834static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
835{
836 struct jsm_channel *ch;
837 int linestatus;
838 unsigned long lock_flags;
839
840 if (!brd)
841 return;
842
843 if (port > brd->maxports)
844 return;
845
846 ch = brd->channels[port];
847 if (!ch)
848 return;
849
850 linestatus = readb(&ch->ch_neo_uart->lsr);
851
852 jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
853 "%s:%d port: %d linestatus: %x\n", __FILE__, __LINE__, port, linestatus);
854
855 ch->ch_cached_lsr |= linestatus;
856
857 if (ch->ch_cached_lsr & UART_LSR_DR) {
858 /* Read data from uart -> queue */
859 neo_copy_data_from_uart_to_queue(ch);
860 spin_lock_irqsave(&ch->ch_lock, lock_flags);
861 jsm_check_queue_flow_control(ch);
862 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
863 }
864
865 /*
866 * This is a special flag. It indicates that at least 1
867 * RX error (parity, framing, or break) has happened.
868 * Mark this in our struct, which will tell me that I have
869 *to do the special RX+LSR read for this FIFO load.
870 */
871 if (linestatus & UART_17158_RX_FIFO_DATA_ERROR)
872 jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
873 "%s:%d Port: %d Got an RX error, need to parse LSR\n",
874 __FILE__, __LINE__, port);
875
876 /*
877 * The next 3 tests should *NOT* happen, as the above test
878 * should encapsulate all 3... At least, thats what Exar says.
879 */
880
881 if (linestatus & UART_LSR_PE) {
882 ch->ch_err_parity++;
883 jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
884 "%s:%d Port: %d. PAR ERR!\n", __FILE__, __LINE__, port);
885 }
886
887 if (linestatus & UART_LSR_FE) {
888 ch->ch_err_frame++;
889 jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
890 "%s:%d Port: %d. FRM ERR!\n", __FILE__, __LINE__, port);
891 }
892
893 if (linestatus & UART_LSR_BI) {
894 ch->ch_err_break++;
895 jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
896 "%s:%d Port: %d. BRK INTR!\n", __FILE__, __LINE__, port);
897 }
898
899 if (linestatus & UART_LSR_OE) {
900 /*
901 * Rx Oruns. Exar says that an orun will NOT corrupt
902 * the FIFO. It will just replace the holding register
903 * with this new data byte. So basically just ignore this.
904 * Probably we should eventually have an orun stat in our driver...
905 */
906 ch->ch_err_overrun++;
907 jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
908 "%s:%d Port: %d. Rx Overrun!\n", __FILE__, __LINE__, port);
909 }
910
911 if (linestatus & UART_LSR_THRE) {
912 spin_lock_irqsave(&ch->ch_lock, lock_flags);
913 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
914 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
915
916 /* Transfer data (if any) from Write Queue -> UART. */
917 neo_copy_data_from_queue_to_uart(ch);
918 }
919 else if (linestatus & UART_17158_TX_AND_FIFO_CLR) {
920 spin_lock_irqsave(&ch->ch_lock, lock_flags);
921 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
922 spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
923
924 /* Transfer data (if any) from Write Queue -> UART. */
925 neo_copy_data_from_queue_to_uart(ch);
926 }
927}
928
929/*
930 * neo_param()
931 * Send any/all changes to the line to the UART.
932 */
933static void neo_param(struct jsm_channel *ch)
934{
935 u8 lcr = 0;
936 u8 uart_lcr, ier;
937 u32 baud;
938 int quot;
939 struct jsm_board *bd;
940
941 bd = ch->ch_bd;
942 if (!bd)
943 return;
944
945 /*
946 * If baud rate is zero, flush queues, and set mval to drop DTR.
947 */
948 if ((ch->ch_c_cflag & (CBAUD)) == 0) {
949 ch->ch_r_head = ch->ch_r_tail = 0;
950 ch->ch_e_head = ch->ch_e_tail = 0;
951
952 neo_flush_uart_write(ch);
953 neo_flush_uart_read(ch);
954
955 ch->ch_flags |= (CH_BAUD0);
956 ch->ch_mostat &= ~(UART_MCR_RTS | UART_MCR_DTR);
957 neo_assert_modem_signals(ch);
958 return;
959
960 } else {
961 int i;
962 unsigned int cflag;
963 static struct {
964 unsigned int rate;
965 unsigned int cflag;
966 } baud_rates[] = {
967 { 921600, B921600 },
968 { 460800, B460800 },
969 { 230400, B230400 },
970 { 115200, B115200 },
971 { 57600, B57600 },
972 { 38400, B38400 },
973 { 19200, B19200 },
974 { 9600, B9600 },
975 { 4800, B4800 },
976 { 2400, B2400 },
977 { 1200, B1200 },
978 { 600, B600 },
979 { 300, B300 },
980 { 200, B200 },
981 { 150, B150 },
982 { 134, B134 },
983 { 110, B110 },
984 { 75, B75 },
985 { 50, B50 },
986 };
987
988 cflag = C_BAUD(ch->uart_port.state->port.tty);
989 baud = 9600;
990 for (i = 0; i < ARRAY_SIZE(baud_rates); i++) {
991 if (baud_rates[i].cflag == cflag) {
992 baud = baud_rates[i].rate;
993 break;
994 }
995 }
996
997 if (ch->ch_flags & CH_BAUD0)
998 ch->ch_flags &= ~(CH_BAUD0);
999 }
1000
1001 if (ch->ch_c_cflag & PARENB)
1002 lcr |= UART_LCR_PARITY;
1003
1004 if (!(ch->ch_c_cflag & PARODD))
1005 lcr |= UART_LCR_EPAR;
1006
1007 /*
1008 * Not all platforms support mark/space parity,
1009 * so this will hide behind an ifdef.
1010 */
1011#ifdef CMSPAR
1012 if (ch->ch_c_cflag & CMSPAR)
1013 lcr |= UART_LCR_SPAR;
1014#endif
1015
1016 if (ch->ch_c_cflag & CSTOPB)
1017 lcr |= UART_LCR_STOP;
1018
1019 switch (ch->ch_c_cflag & CSIZE) {
1020 case CS5:
1021 lcr |= UART_LCR_WLEN5;
1022 break;
1023 case CS6:
1024 lcr |= UART_LCR_WLEN6;
1025 break;
1026 case CS7:
1027 lcr |= UART_LCR_WLEN7;
1028 break;
1029 case CS8:
1030 default:
1031 lcr |= UART_LCR_WLEN8;
1032 break;
1033 }
1034
1035 ier = readb(&ch->ch_neo_uart->ier);
1036 uart_lcr = readb(&ch->ch_neo_uart->lcr);
1037
1038 if (baud == 0)
1039 baud = 9600;
1040
1041 quot = ch->ch_bd->bd_dividend / baud;
1042
1043 if (quot != 0) {
1044 writeb(UART_LCR_DLAB, &ch->ch_neo_uart->lcr);
1045 writeb((quot & 0xff), &ch->ch_neo_uart->txrx);
1046 writeb((quot >> 8), &ch->ch_neo_uart->ier);
1047 writeb(lcr, &ch->ch_neo_uart->lcr);
1048 }
1049
1050 if (uart_lcr != lcr)
1051 writeb(lcr, &ch->ch_neo_uart->lcr);
1052
1053 if (ch->ch_c_cflag & CREAD)
1054 ier |= (UART_IER_RDI | UART_IER_RLSI);
1055
1056 ier |= (UART_IER_THRI | UART_IER_MSI);
1057
1058 writeb(ier, &ch->ch_neo_uart->ier);
1059
1060 /* Set new start/stop chars */
1061 neo_set_new_start_stop_chars(ch);
1062
1063 if (ch->ch_c_cflag & CRTSCTS)
1064 neo_set_cts_flow_control(ch);
1065 else if (ch->ch_c_iflag & IXON) {
1066 /* If start/stop is set to disable, then we should disable flow control */
1067 if ((ch->ch_startc == __DISABLED_CHAR) || (ch->ch_stopc == __DISABLED_CHAR))
1068 neo_set_no_output_flow_control(ch);
1069 else
1070 neo_set_ixon_flow_control(ch);
1071 }
1072 else
1073 neo_set_no_output_flow_control(ch);
1074
1075 if (ch->ch_c_cflag & CRTSCTS)
1076 neo_set_rts_flow_control(ch);
1077 else if (ch->ch_c_iflag & IXOFF) {
1078 /* If start/stop is set to disable, then we should disable flow control */
1079 if ((ch->ch_startc == __DISABLED_CHAR) || (ch->ch_stopc == __DISABLED_CHAR))
1080 neo_set_no_input_flow_control(ch);
1081 else
1082 neo_set_ixoff_flow_control(ch);
1083 }
1084 else
1085 neo_set_no_input_flow_control(ch);
1086 /*
1087 * Adjust the RX FIFO Trigger level if baud is less than 9600.
1088 * Not exactly elegant, but this is needed because of the Exar chip's
1089 * delay on firing off the RX FIFO interrupt on slower baud rates.
1090 */
1091 if (baud < 9600) {
1092 writeb(1, &ch->ch_neo_uart->rfifo);
1093 ch->ch_r_tlevel = 1;
1094 }
1095
1096 neo_assert_modem_signals(ch);
1097
1098 /* Get current status of the modem signals now */
1099 neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr));
1100 return;
1101}
1102
1103/*
1104 * jsm_neo_intr()
1105 *
1106 * Neo specific interrupt handler.
1107 */
1108static irqreturn_t neo_intr(int irq, void *voidbrd)
1109{
1110 struct jsm_board *brd = voidbrd;
1111 struct jsm_channel *ch;
1112 int port = 0;
1113 int type = 0;
1114 int current_port;
1115 u32 tmp;
1116 u32 uart_poll;
1117 unsigned long lock_flags;
1118 unsigned long lock_flags2;
1119 int outofloop_count = 0;
1120
1121 /* Lock out the slow poller from running on this board. */
1122 spin_lock_irqsave(&brd->bd_intr_lock, lock_flags);
1123
1124 /*
1125 * Read in "extended" IRQ information from the 32bit Neo register.
1126 * Bits 0-7: What port triggered the interrupt.
1127 * Bits 8-31: Each 3bits indicate what type of interrupt occurred.
1128 */
1129 uart_poll = readl(brd->re_map_membase + UART_17158_POLL_ADDR_OFFSET);
1130
1131 jsm_printk(INTR, INFO, &brd->pci_dev,
1132 "%s:%d uart_poll: %x\n", __FILE__, __LINE__, uart_poll);
1133
1134 if (!uart_poll) {
1135 jsm_printk(INTR, INFO, &brd->pci_dev,
1136 "Kernel interrupted to me, but no pending interrupts...\n");
1137 spin_unlock_irqrestore(&brd->bd_intr_lock, lock_flags);
1138 return IRQ_NONE;
1139 }
1140
1141 /* At this point, we have at least SOMETHING to service, dig further... */
1142
1143 current_port = 0;
1144
1145 /* Loop on each port */
1146 while (((uart_poll & 0xff) != 0) && (outofloop_count < 0xff)){
1147
1148 tmp = uart_poll;
1149 outofloop_count++;
1150
1151 /* Check current port to see if it has interrupt pending */
1152 if ((tmp & jsm_offset_table[current_port]) != 0) {
1153 port = current_port;
1154 type = tmp >> (8 + (port * 3));
1155 type &= 0x7;
1156 } else {
1157 current_port++;
1158 continue;
1159 }
1160
1161 jsm_printk(INTR, INFO, &brd->pci_dev,
1162 "%s:%d port: %x type: %x\n", __FILE__, __LINE__, port, type);
1163
1164 /* Remove this port + type from uart_poll */
1165 uart_poll &= ~(jsm_offset_table[port]);
1166
1167 if (!type) {
1168 /* If no type, just ignore it, and move onto next port */
1169 jsm_printk(INTR, ERR, &brd->pci_dev,
1170 "Interrupt with no type! port: %d\n", port);
1171 continue;
1172 }
1173
1174 /* Switch on type of interrupt we have */
1175 switch (type) {
1176
1177 case UART_17158_RXRDY_TIMEOUT:
1178 /*
1179 * RXRDY Time-out is cleared by reading data in the
1180 * RX FIFO until it falls below the trigger level.
1181 */
1182
1183 /* Verify the port is in range. */
1184 if (port > brd->nasync)
1185 continue;
1186
1187 ch = brd->channels[port];
1188 neo_copy_data_from_uart_to_queue(ch);
1189
1190 /* Call our tty layer to enforce queue flow control if needed. */
1191 spin_lock_irqsave(&ch->ch_lock, lock_flags2);
1192 jsm_check_queue_flow_control(ch);
1193 spin_unlock_irqrestore(&ch->ch_lock, lock_flags2);
1194
1195 continue;
1196
1197 case UART_17158_RX_LINE_STATUS:
1198 /*
1199 * RXRDY and RX LINE Status (logic OR of LSR[4:1])
1200 */
1201 neo_parse_lsr(brd, port);
1202 continue;
1203
1204 case UART_17158_TXRDY:
1205 /*
1206 * TXRDY interrupt clears after reading ISR register for the UART channel.
1207 */
1208
1209 /*
1210 * Yes, this is odd...
1211 * Why would I check EVERY possibility of type of
1212 * interrupt, when we know its TXRDY???
1213 * Becuz for some reason, even tho we got triggered for TXRDY,
1214 * it seems to be occasionally wrong. Instead of TX, which
1215 * it should be, I was getting things like RXDY too. Weird.
1216 */
1217 neo_parse_isr(brd, port);
1218 continue;
1219
1220 case UART_17158_MSR:
1221 /*
1222 * MSR or flow control was seen.
1223 */
1224 neo_parse_isr(brd, port);
1225 continue;
1226
1227 default:
1228 /*
1229 * The UART triggered us with a bogus interrupt type.
1230 * It appears the Exar chip, when REALLY bogged down, will throw
1231 * these once and awhile.
1232 * Its harmless, just ignore it and move on.
1233 */
1234 jsm_printk(INTR, ERR, &brd->pci_dev,
1235 "%s:%d Unknown Interrupt type: %x\n", __FILE__, __LINE__, type);
1236 continue;
1237 }
1238 }
1239
1240 spin_unlock_irqrestore(&brd->bd_intr_lock, lock_flags);
1241
1242 jsm_printk(INTR, INFO, &brd->pci_dev, "finish.\n");
1243 return IRQ_HANDLED;
1244}
1245
1246/*
1247 * Neo specific way of turning off the receiver.
1248 * Used as a way to enforce queue flow control when in
1249 * hardware flow control mode.
1250 */
1251static void neo_disable_receiver(struct jsm_channel *ch)
1252{
1253 u8 tmp = readb(&ch->ch_neo_uart->ier);
1254 tmp &= ~(UART_IER_RDI);
1255 writeb(tmp, &ch->ch_neo_uart->ier);
1256
1257 /* flush write operation */
1258 neo_pci_posting_flush(ch->ch_bd);
1259}
1260
1261
1262/*
1263 * Neo specific way of turning on the receiver.
1264 * Used as a way to un-enforce queue flow control when in
1265 * hardware flow control mode.
1266 */
1267static void neo_enable_receiver(struct jsm_channel *ch)
1268{
1269 u8 tmp = readb(&ch->ch_neo_uart->ier);
1270 tmp |= (UART_IER_RDI);
1271 writeb(tmp, &ch->ch_neo_uart->ier);
1272
1273 /* flush write operation */
1274 neo_pci_posting_flush(ch->ch_bd);
1275}
1276
1277static void neo_send_start_character(struct jsm_channel *ch)
1278{
1279 if (!ch)
1280 return;
1281
1282 if (ch->ch_startc != __DISABLED_CHAR) {
1283 ch->ch_xon_sends++;
1284 writeb(ch->ch_startc, &ch->ch_neo_uart->txrx);
1285
1286 /* flush write operation */
1287 neo_pci_posting_flush(ch->ch_bd);
1288 }
1289}
1290
1291static void neo_send_stop_character(struct jsm_channel *ch)
1292{
1293 if (!ch)
1294 return;
1295
1296 if (ch->ch_stopc != __DISABLED_CHAR) {
1297 ch->ch_xoff_sends++;
1298 writeb(ch->ch_stopc, &ch->ch_neo_uart->txrx);
1299
1300 /* flush write operation */
1301 neo_pci_posting_flush(ch->ch_bd);
1302 }
1303}
1304
1305/*
1306 * neo_uart_init
1307 */
1308static void neo_uart_init(struct jsm_channel *ch)
1309{
1310 writeb(0, &ch->ch_neo_uart->ier);
1311 writeb(0, &ch->ch_neo_uart->efr);
1312 writeb(UART_EFR_ECB, &ch->ch_neo_uart->efr);
1313
1314 /* Clear out UART and FIFO */
1315 readb(&ch->ch_neo_uart->txrx);
1316 writeb((UART_FCR_ENABLE_FIFO|UART_FCR_CLEAR_RCVR|UART_FCR_CLEAR_XMIT), &ch->ch_neo_uart->isr_fcr);
1317 readb(&ch->ch_neo_uart->lsr);
1318 readb(&ch->ch_neo_uart->msr);
1319
1320 ch->ch_flags |= CH_FIFO_ENABLED;
1321
1322 /* Assert any signals we want up */
1323 writeb(ch->ch_mostat, &ch->ch_neo_uart->mcr);
1324}
1325
1326/*
1327 * Make the UART completely turn off.
1328 */
1329static void neo_uart_off(struct jsm_channel *ch)
1330{
1331 /* Turn off UART enhanced bits */
1332 writeb(0, &ch->ch_neo_uart->efr);
1333
1334 /* Stop all interrupts from occurring. */
1335 writeb(0, &ch->ch_neo_uart->ier);
1336}
1337
1338static u32 neo_get_uart_bytes_left(struct jsm_channel *ch)
1339{
1340 u8 left = 0;
1341 u8 lsr = readb(&ch->ch_neo_uart->lsr);
1342
1343 /* We must cache the LSR as some of the bits get reset once read... */
1344 ch->ch_cached_lsr |= lsr;
1345
1346 /* Determine whether the Transmitter is empty or not */
1347 if (!(lsr & UART_LSR_TEMT))
1348 left = 1;
1349 else {
1350 ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
1351 left = 0;
1352 }
1353
1354 return left;
1355}
1356
1357/* Channel lock MUST be held by the calling function! */
1358static void neo_send_break(struct jsm_channel *ch)
1359{
1360 /*
1361 * Set the time we should stop sending the break.
1362 * If we are already sending a break, toss away the existing
1363 * time to stop, and use this new value instead.
1364 */
1365
1366 /* Tell the UART to start sending the break */
1367 if (!(ch->ch_flags & CH_BREAK_SENDING)) {
1368 u8 temp = readb(&ch->ch_neo_uart->lcr);
1369 writeb((temp | UART_LCR_SBC), &ch->ch_neo_uart->lcr);
1370 ch->ch_flags |= (CH_BREAK_SENDING);
1371
1372 /* flush write operation */
1373 neo_pci_posting_flush(ch->ch_bd);
1374 }
1375}
1376
1377/*
1378 * neo_send_immediate_char.
1379 *
1380 * Sends a specific character as soon as possible to the UART,
1381 * jumping over any bytes that might be in the write queue.
1382 *
1383 * The channel lock MUST be held by the calling function.
1384 */
1385static void neo_send_immediate_char(struct jsm_channel *ch, unsigned char c)
1386{
1387 if (!ch)
1388 return;
1389
1390 writeb(c, &ch->ch_neo_uart->txrx);
1391
1392 /* flush write operation */
1393 neo_pci_posting_flush(ch->ch_bd);
1394}
1395
1396struct board_ops jsm_neo_ops = {
1397 .intr = neo_intr,
1398 .uart_init = neo_uart_init,
1399 .uart_off = neo_uart_off,
1400 .param = neo_param,
1401 .assert_modem_signals = neo_assert_modem_signals,
1402 .flush_uart_write = neo_flush_uart_write,
1403 .flush_uart_read = neo_flush_uart_read,
1404 .disable_receiver = neo_disable_receiver,
1405 .enable_receiver = neo_enable_receiver,
1406 .send_break = neo_send_break,
1407 .clear_break = neo_clear_break,
1408 .send_start_character = neo_send_start_character,
1409 .send_stop_character = neo_send_stop_character,
1410 .copy_data_from_queue_to_uart = neo_copy_data_from_queue_to_uart,
1411 .get_uart_bytes_left = neo_get_uart_bytes_left,
1412 .send_immediate_char = neo_send_immediate_char
1413};