Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Driver for Atmel AT91 Serial ports
4 * Copyright (C) 2003 Rick Bronson
5 *
6 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
7 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
8 *
9 * DMA support added by Chip Coldwell.
10 */
11#include <linux/tty.h>
12#include <linux/ioport.h>
13#include <linux/slab.h>
14#include <linux/init.h>
15#include <linux/serial.h>
16#include <linux/clk.h>
17#include <linux/console.h>
18#include <linux/sysrq.h>
19#include <linux/tty_flip.h>
20#include <linux/platform_device.h>
21#include <linux/of.h>
22#include <linux/of_device.h>
23#include <linux/dma-mapping.h>
24#include <linux/dmaengine.h>
25#include <linux/atmel_pdc.h>
26#include <linux/uaccess.h>
27#include <linux/platform_data/atmel.h>
28#include <linux/timer.h>
29#include <linux/err.h>
30#include <linux/irq.h>
31#include <linux/suspend.h>
32#include <linux/mm.h>
33#include <linux/io.h>
34
35#include <asm/div64.h>
36#include <asm/ioctls.h>
37
38#define PDC_BUFFER_SIZE 512
39/* Revisit: We should calculate this based on the actual port settings */
40#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
41
42/* The minium number of data FIFOs should be able to contain */
43#define ATMEL_MIN_FIFO_SIZE 8
44/*
45 * These two offsets are substracted from the RX FIFO size to define the RTS
46 * high and low thresholds
47 */
48#define ATMEL_RTS_HIGH_OFFSET 16
49#define ATMEL_RTS_LOW_OFFSET 20
50
51#include <linux/serial_core.h>
52
53#include "serial_mctrl_gpio.h"
54#include "atmel_serial.h"
55
56static void atmel_start_rx(struct uart_port *port);
57static void atmel_stop_rx(struct uart_port *port);
58
59#ifdef CONFIG_SERIAL_ATMEL_TTYAT
60
61/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
62 * should coexist with the 8250 driver, such as if we have an external 16C550
63 * UART. */
64#define SERIAL_ATMEL_MAJOR 204
65#define MINOR_START 154
66#define ATMEL_DEVICENAME "ttyAT"
67
68#else
69
70/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
71 * name, but it is legally reserved for the 8250 driver. */
72#define SERIAL_ATMEL_MAJOR TTY_MAJOR
73#define MINOR_START 64
74#define ATMEL_DEVICENAME "ttyS"
75
76#endif
77
78#define ATMEL_ISR_PASS_LIMIT 256
79
80struct atmel_dma_buffer {
81 unsigned char *buf;
82 dma_addr_t dma_addr;
83 unsigned int dma_size;
84 unsigned int ofs;
85};
86
87struct atmel_uart_char {
88 u16 status;
89 u16 ch;
90};
91
92/*
93 * Be careful, the real size of the ring buffer is
94 * sizeof(atmel_uart_char) * ATMEL_SERIAL_RINGSIZE. It means that ring buffer
95 * can contain up to 1024 characters in PIO mode and up to 4096 characters in
96 * DMA mode.
97 */
98#define ATMEL_SERIAL_RINGSIZE 1024
99
100/*
101 * at91: 6 USARTs and one DBGU port (SAM9260)
102 * samx7: 3 USARTs and 5 UARTs
103 */
104#define ATMEL_MAX_UART 8
105
106/*
107 * We wrap our port structure around the generic uart_port.
108 */
109struct atmel_uart_port {
110 struct uart_port uart; /* uart */
111 struct clk *clk; /* uart clock */
112 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
113 u32 backup_imr; /* IMR saved during suspend */
114 int break_active; /* break being received */
115
116 bool use_dma_rx; /* enable DMA receiver */
117 bool use_pdc_rx; /* enable PDC receiver */
118 short pdc_rx_idx; /* current PDC RX buffer */
119 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
120
121 bool use_dma_tx; /* enable DMA transmitter */
122 bool use_pdc_tx; /* enable PDC transmitter */
123 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
124
125 spinlock_t lock_tx; /* port lock */
126 spinlock_t lock_rx; /* port lock */
127 struct dma_chan *chan_tx;
128 struct dma_chan *chan_rx;
129 struct dma_async_tx_descriptor *desc_tx;
130 struct dma_async_tx_descriptor *desc_rx;
131 dma_cookie_t cookie_tx;
132 dma_cookie_t cookie_rx;
133 struct scatterlist sg_tx;
134 struct scatterlist sg_rx;
135 struct tasklet_struct tasklet_rx;
136 struct tasklet_struct tasklet_tx;
137 atomic_t tasklet_shutdown;
138 unsigned int irq_status_prev;
139 unsigned int tx_len;
140
141 struct circ_buf rx_ring;
142
143 struct mctrl_gpios *gpios;
144 u32 backup_mode; /* MR saved during iso7816 operations */
145 u32 backup_brgr; /* BRGR saved during iso7816 operations */
146 unsigned int tx_done_mask;
147 u32 fifo_size;
148 u32 rts_high;
149 u32 rts_low;
150 bool ms_irq_enabled;
151 u32 rtor; /* address of receiver timeout register if it exists */
152 bool has_frac_baudrate;
153 bool has_hw_timer;
154 struct timer_list uart_timer;
155
156 bool tx_stopped;
157 bool suspended;
158 unsigned int pending;
159 unsigned int pending_status;
160 spinlock_t lock_suspended;
161
162 bool hd_start_rx; /* can start RX during half-duplex operation */
163
164 /* ISO7816 */
165 unsigned int fidi_min;
166 unsigned int fidi_max;
167
168#ifdef CONFIG_PM
169 struct {
170 u32 cr;
171 u32 mr;
172 u32 imr;
173 u32 brgr;
174 u32 rtor;
175 u32 ttgr;
176 u32 fmr;
177 u32 fimr;
178 } cache;
179#endif
180
181 int (*prepare_rx)(struct uart_port *port);
182 int (*prepare_tx)(struct uart_port *port);
183 void (*schedule_rx)(struct uart_port *port);
184 void (*schedule_tx)(struct uart_port *port);
185 void (*release_rx)(struct uart_port *port);
186 void (*release_tx)(struct uart_port *port);
187};
188
189static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
190static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART);
191
192#if defined(CONFIG_OF)
193static const struct of_device_id atmel_serial_dt_ids[] = {
194 { .compatible = "atmel,at91rm9200-usart-serial" },
195 { /* sentinel */ }
196};
197#endif
198
199static inline struct atmel_uart_port *
200to_atmel_uart_port(struct uart_port *uart)
201{
202 return container_of(uart, struct atmel_uart_port, uart);
203}
204
205static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg)
206{
207 return __raw_readl(port->membase + reg);
208}
209
210static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
211{
212 __raw_writel(value, port->membase + reg);
213}
214
215static inline u8 atmel_uart_read_char(struct uart_port *port)
216{
217 return __raw_readb(port->membase + ATMEL_US_RHR);
218}
219
220static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
221{
222 __raw_writeb(value, port->membase + ATMEL_US_THR);
223}
224
225static inline int atmel_uart_is_half_duplex(struct uart_port *port)
226{
227 return ((port->rs485.flags & SER_RS485_ENABLED) &&
228 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
229 (port->iso7816.flags & SER_ISO7816_ENABLED);
230}
231
232#ifdef CONFIG_SERIAL_ATMEL_PDC
233static bool atmel_use_pdc_rx(struct uart_port *port)
234{
235 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
236
237 return atmel_port->use_pdc_rx;
238}
239
240static bool atmel_use_pdc_tx(struct uart_port *port)
241{
242 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
243
244 return atmel_port->use_pdc_tx;
245}
246#else
247static bool atmel_use_pdc_rx(struct uart_port *port)
248{
249 return false;
250}
251
252static bool atmel_use_pdc_tx(struct uart_port *port)
253{
254 return false;
255}
256#endif
257
258static bool atmel_use_dma_tx(struct uart_port *port)
259{
260 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
261
262 return atmel_port->use_dma_tx;
263}
264
265static bool atmel_use_dma_rx(struct uart_port *port)
266{
267 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
268
269 return atmel_port->use_dma_rx;
270}
271
272static bool atmel_use_fifo(struct uart_port *port)
273{
274 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
275
276 return atmel_port->fifo_size;
277}
278
279static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port,
280 struct tasklet_struct *t)
281{
282 if (!atomic_read(&atmel_port->tasklet_shutdown))
283 tasklet_schedule(t);
284}
285
286/* Enable or disable the rs485 support */
287static int atmel_config_rs485(struct uart_port *port,
288 struct serial_rs485 *rs485conf)
289{
290 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
291 unsigned int mode;
292
293 /* Disable interrupts */
294 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
295
296 mode = atmel_uart_readl(port, ATMEL_US_MR);
297
298 /* Resetting serial mode to RS232 (0x0) */
299 mode &= ~ATMEL_US_USMODE;
300
301 port->rs485 = *rs485conf;
302
303 if (rs485conf->flags & SER_RS485_ENABLED) {
304 dev_dbg(port->dev, "Setting UART to RS485\n");
305 if (port->rs485.flags & SER_RS485_RX_DURING_TX)
306 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
307 else
308 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
309
310 atmel_uart_writel(port, ATMEL_US_TTGR,
311 rs485conf->delay_rts_after_send);
312 mode |= ATMEL_US_USMODE_RS485;
313 } else {
314 dev_dbg(port->dev, "Setting UART to RS232\n");
315 if (atmel_use_pdc_tx(port))
316 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
317 ATMEL_US_TXBUFE;
318 else
319 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
320 }
321 atmel_uart_writel(port, ATMEL_US_MR, mode);
322
323 /* Enable interrupts */
324 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
325
326 return 0;
327}
328
329static unsigned int atmel_calc_cd(struct uart_port *port,
330 struct serial_iso7816 *iso7816conf)
331{
332 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
333 unsigned int cd;
334 u64 mck_rate;
335
336 mck_rate = (u64)clk_get_rate(atmel_port->clk);
337 do_div(mck_rate, iso7816conf->clk);
338 cd = mck_rate;
339 return cd;
340}
341
342static unsigned int atmel_calc_fidi(struct uart_port *port,
343 struct serial_iso7816 *iso7816conf)
344{
345 u64 fidi = 0;
346
347 if (iso7816conf->sc_fi && iso7816conf->sc_di) {
348 fidi = (u64)iso7816conf->sc_fi;
349 do_div(fidi, iso7816conf->sc_di);
350 }
351 return (u32)fidi;
352}
353
354/* Enable or disable the iso7816 support */
355/* Called with interrupts disabled */
356static int atmel_config_iso7816(struct uart_port *port,
357 struct serial_iso7816 *iso7816conf)
358{
359 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
360 unsigned int mode;
361 unsigned int cd, fidi;
362 int ret = 0;
363
364 /* Disable interrupts */
365 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
366
367 mode = atmel_uart_readl(port, ATMEL_US_MR);
368
369 if (iso7816conf->flags & SER_ISO7816_ENABLED) {
370 mode &= ~ATMEL_US_USMODE;
371
372 if (iso7816conf->tg > 255) {
373 dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n");
374 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
375 ret = -EINVAL;
376 goto err_out;
377 }
378
379 if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
380 == SER_ISO7816_T(0)) {
381 mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK;
382 } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
383 == SER_ISO7816_T(1)) {
384 mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK;
385 } else {
386 dev_err(port->dev, "ISO7816: Type not supported\n");
387 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
388 ret = -EINVAL;
389 goto err_out;
390 }
391
392 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR);
393
394 /* select mck clock, and output */
395 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
396 /* set parity for normal/inverse mode + max iterations */
397 mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3);
398
399 cd = atmel_calc_cd(port, iso7816conf);
400 fidi = atmel_calc_fidi(port, iso7816conf);
401 if (fidi == 0) {
402 dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n");
403 } else if (fidi < atmel_port->fidi_min
404 || fidi > atmel_port->fidi_max) {
405 dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi);
406 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
407 ret = -EINVAL;
408 goto err_out;
409 }
410
411 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) {
412 /* port not yet in iso7816 mode: store configuration */
413 atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR);
414 atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
415 }
416
417 atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg);
418 atmel_uart_writel(port, ATMEL_US_BRGR, cd);
419 atmel_uart_writel(port, ATMEL_US_FIDI, fidi);
420
421 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN);
422 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION;
423 } else {
424 dev_dbg(port->dev, "Setting UART back to RS232\n");
425 /* back to last RS232 settings */
426 mode = atmel_port->backup_mode;
427 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
428 atmel_uart_writel(port, ATMEL_US_TTGR, 0);
429 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr);
430 atmel_uart_writel(port, ATMEL_US_FIDI, 0x174);
431
432 if (atmel_use_pdc_tx(port))
433 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
434 ATMEL_US_TXBUFE;
435 else
436 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
437 }
438
439 port->iso7816 = *iso7816conf;
440
441 atmel_uart_writel(port, ATMEL_US_MR, mode);
442
443err_out:
444 /* Enable interrupts */
445 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
446
447 return ret;
448}
449
450/*
451 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
452 */
453static u_int atmel_tx_empty(struct uart_port *port)
454{
455 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
456
457 if (atmel_port->tx_stopped)
458 return TIOCSER_TEMT;
459 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
460 TIOCSER_TEMT :
461 0;
462}
463
464/*
465 * Set state of the modem control output lines
466 */
467static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
468{
469 unsigned int control = 0;
470 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR);
471 unsigned int rts_paused, rts_ready;
472 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
473
474 /* override mode to RS485 if needed, otherwise keep the current mode */
475 if (port->rs485.flags & SER_RS485_ENABLED) {
476 atmel_uart_writel(port, ATMEL_US_TTGR,
477 port->rs485.delay_rts_after_send);
478 mode &= ~ATMEL_US_USMODE;
479 mode |= ATMEL_US_USMODE_RS485;
480 }
481
482 /* set the RTS line state according to the mode */
483 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
484 /* force RTS line to high level */
485 rts_paused = ATMEL_US_RTSEN;
486
487 /* give the control of the RTS line back to the hardware */
488 rts_ready = ATMEL_US_RTSDIS;
489 } else {
490 /* force RTS line to high level */
491 rts_paused = ATMEL_US_RTSDIS;
492
493 /* force RTS line to low level */
494 rts_ready = ATMEL_US_RTSEN;
495 }
496
497 if (mctrl & TIOCM_RTS)
498 control |= rts_ready;
499 else
500 control |= rts_paused;
501
502 if (mctrl & TIOCM_DTR)
503 control |= ATMEL_US_DTREN;
504 else
505 control |= ATMEL_US_DTRDIS;
506
507 atmel_uart_writel(port, ATMEL_US_CR, control);
508
509 mctrl_gpio_set(atmel_port->gpios, mctrl);
510
511 /* Local loopback mode? */
512 mode &= ~ATMEL_US_CHMODE;
513 if (mctrl & TIOCM_LOOP)
514 mode |= ATMEL_US_CHMODE_LOC_LOOP;
515 else
516 mode |= ATMEL_US_CHMODE_NORMAL;
517
518 atmel_uart_writel(port, ATMEL_US_MR, mode);
519}
520
521/*
522 * Get state of the modem control input lines
523 */
524static u_int atmel_get_mctrl(struct uart_port *port)
525{
526 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
527 unsigned int ret = 0, status;
528
529 status = atmel_uart_readl(port, ATMEL_US_CSR);
530
531 /*
532 * The control signals are active low.
533 */
534 if (!(status & ATMEL_US_DCD))
535 ret |= TIOCM_CD;
536 if (!(status & ATMEL_US_CTS))
537 ret |= TIOCM_CTS;
538 if (!(status & ATMEL_US_DSR))
539 ret |= TIOCM_DSR;
540 if (!(status & ATMEL_US_RI))
541 ret |= TIOCM_RI;
542
543 return mctrl_gpio_get(atmel_port->gpios, &ret);
544}
545
546/*
547 * Stop transmitting.
548 */
549static void atmel_stop_tx(struct uart_port *port)
550{
551 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
552
553 if (atmel_use_pdc_tx(port)) {
554 /* disable PDC transmit */
555 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
556 }
557
558 /*
559 * Disable the transmitter.
560 * This is mandatory when DMA is used, otherwise the DMA buffer
561 * is fully transmitted.
562 */
563 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
564 atmel_port->tx_stopped = true;
565
566 /* Disable interrupts */
567 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
568
569 if (atmel_uart_is_half_duplex(port))
570 if (!atomic_read(&atmel_port->tasklet_shutdown))
571 atmel_start_rx(port);
572
573}
574
575/*
576 * Start transmitting.
577 */
578static void atmel_start_tx(struct uart_port *port)
579{
580 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
581
582 if (atmel_use_pdc_tx(port) && (atmel_uart_readl(port, ATMEL_PDC_PTSR)
583 & ATMEL_PDC_TXTEN))
584 /* The transmitter is already running. Yes, we
585 really need this.*/
586 return;
587
588 if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
589 if (atmel_uart_is_half_duplex(port))
590 atmel_stop_rx(port);
591
592 if (atmel_use_pdc_tx(port))
593 /* re-enable PDC transmit */
594 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
595
596 /* Enable interrupts */
597 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
598
599 /* re-enable the transmitter */
600 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
601 atmel_port->tx_stopped = false;
602}
603
604/*
605 * start receiving - port is in process of being opened.
606 */
607static void atmel_start_rx(struct uart_port *port)
608{
609 /* reset status and receiver */
610 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
611
612 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN);
613
614 if (atmel_use_pdc_rx(port)) {
615 /* enable PDC controller */
616 atmel_uart_writel(port, ATMEL_US_IER,
617 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
618 port->read_status_mask);
619 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
620 } else {
621 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
622 }
623}
624
625/*
626 * Stop receiving - port is in process of being closed.
627 */
628static void atmel_stop_rx(struct uart_port *port)
629{
630 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS);
631
632 if (atmel_use_pdc_rx(port)) {
633 /* disable PDC receive */
634 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS);
635 atmel_uart_writel(port, ATMEL_US_IDR,
636 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
637 port->read_status_mask);
638 } else {
639 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY);
640 }
641}
642
643/*
644 * Enable modem status interrupts
645 */
646static void atmel_enable_ms(struct uart_port *port)
647{
648 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
649 uint32_t ier = 0;
650
651 /*
652 * Interrupt should not be enabled twice
653 */
654 if (atmel_port->ms_irq_enabled)
655 return;
656
657 atmel_port->ms_irq_enabled = true;
658
659 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
660 ier |= ATMEL_US_CTSIC;
661
662 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
663 ier |= ATMEL_US_DSRIC;
664
665 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
666 ier |= ATMEL_US_RIIC;
667
668 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
669 ier |= ATMEL_US_DCDIC;
670
671 atmel_uart_writel(port, ATMEL_US_IER, ier);
672
673 mctrl_gpio_enable_ms(atmel_port->gpios);
674}
675
676/*
677 * Disable modem status interrupts
678 */
679static void atmel_disable_ms(struct uart_port *port)
680{
681 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
682 uint32_t idr = 0;
683
684 /*
685 * Interrupt should not be disabled twice
686 */
687 if (!atmel_port->ms_irq_enabled)
688 return;
689
690 atmel_port->ms_irq_enabled = false;
691
692 mctrl_gpio_disable_ms(atmel_port->gpios);
693
694 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
695 idr |= ATMEL_US_CTSIC;
696
697 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
698 idr |= ATMEL_US_DSRIC;
699
700 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
701 idr |= ATMEL_US_RIIC;
702
703 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
704 idr |= ATMEL_US_DCDIC;
705
706 atmel_uart_writel(port, ATMEL_US_IDR, idr);
707}
708
709/*
710 * Control the transmission of a break signal
711 */
712static void atmel_break_ctl(struct uart_port *port, int break_state)
713{
714 if (break_state != 0)
715 /* start break */
716 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK);
717 else
718 /* stop break */
719 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK);
720}
721
722/*
723 * Stores the incoming character in the ring buffer
724 */
725static void
726atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
727 unsigned int ch)
728{
729 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
730 struct circ_buf *ring = &atmel_port->rx_ring;
731 struct atmel_uart_char *c;
732
733 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
734 /* Buffer overflow, ignore char */
735 return;
736
737 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
738 c->status = status;
739 c->ch = ch;
740
741 /* Make sure the character is stored before we update head. */
742 smp_wmb();
743
744 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
745}
746
747/*
748 * Deal with parity, framing and overrun errors.
749 */
750static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
751{
752 /* clear error */
753 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
754
755 if (status & ATMEL_US_RXBRK) {
756 /* ignore side-effect */
757 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
758 port->icount.brk++;
759 }
760 if (status & ATMEL_US_PARE)
761 port->icount.parity++;
762 if (status & ATMEL_US_FRAME)
763 port->icount.frame++;
764 if (status & ATMEL_US_OVRE)
765 port->icount.overrun++;
766}
767
768/*
769 * Characters received (called from interrupt handler)
770 */
771static void atmel_rx_chars(struct uart_port *port)
772{
773 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
774 unsigned int status, ch;
775
776 status = atmel_uart_readl(port, ATMEL_US_CSR);
777 while (status & ATMEL_US_RXRDY) {
778 ch = atmel_uart_read_char(port);
779
780 /*
781 * note that the error handling code is
782 * out of the main execution path
783 */
784 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
785 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
786 || atmel_port->break_active)) {
787
788 /* clear error */
789 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
790
791 if (status & ATMEL_US_RXBRK
792 && !atmel_port->break_active) {
793 atmel_port->break_active = 1;
794 atmel_uart_writel(port, ATMEL_US_IER,
795 ATMEL_US_RXBRK);
796 } else {
797 /*
798 * This is either the end-of-break
799 * condition or we've received at
800 * least one character without RXBRK
801 * being set. In both cases, the next
802 * RXBRK will indicate start-of-break.
803 */
804 atmel_uart_writel(port, ATMEL_US_IDR,
805 ATMEL_US_RXBRK);
806 status &= ~ATMEL_US_RXBRK;
807 atmel_port->break_active = 0;
808 }
809 }
810
811 atmel_buffer_rx_char(port, status, ch);
812 status = atmel_uart_readl(port, ATMEL_US_CSR);
813 }
814
815 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
816}
817
818/*
819 * Transmit characters (called from tasklet with TXRDY interrupt
820 * disabled)
821 */
822static void atmel_tx_chars(struct uart_port *port)
823{
824 struct circ_buf *xmit = &port->state->xmit;
825 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
826
827 if (port->x_char &&
828 (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) {
829 atmel_uart_write_char(port, port->x_char);
830 port->icount.tx++;
831 port->x_char = 0;
832 }
833 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
834 return;
835
836 while (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY) {
837 atmel_uart_write_char(port, xmit->buf[xmit->tail]);
838 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
839 port->icount.tx++;
840 if (uart_circ_empty(xmit))
841 break;
842 }
843
844 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
845 uart_write_wakeup(port);
846
847 if (!uart_circ_empty(xmit)) {
848 /* we still have characters to transmit, so we should continue
849 * transmitting them when TX is ready, regardless of
850 * mode or duplexity
851 */
852 atmel_port->tx_done_mask |= ATMEL_US_TXRDY;
853
854 /* Enable interrupts */
855 atmel_uart_writel(port, ATMEL_US_IER,
856 atmel_port->tx_done_mask);
857 } else {
858 if (atmel_uart_is_half_duplex(port))
859 atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY;
860 }
861}
862
863static void atmel_complete_tx_dma(void *arg)
864{
865 struct atmel_uart_port *atmel_port = arg;
866 struct uart_port *port = &atmel_port->uart;
867 struct circ_buf *xmit = &port->state->xmit;
868 struct dma_chan *chan = atmel_port->chan_tx;
869 unsigned long flags;
870
871 spin_lock_irqsave(&port->lock, flags);
872
873 if (chan)
874 dmaengine_terminate_all(chan);
875 xmit->tail += atmel_port->tx_len;
876 xmit->tail &= UART_XMIT_SIZE - 1;
877
878 port->icount.tx += atmel_port->tx_len;
879
880 spin_lock_irq(&atmel_port->lock_tx);
881 async_tx_ack(atmel_port->desc_tx);
882 atmel_port->cookie_tx = -EINVAL;
883 atmel_port->desc_tx = NULL;
884 spin_unlock_irq(&atmel_port->lock_tx);
885
886 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
887 uart_write_wakeup(port);
888
889 /*
890 * xmit is a circular buffer so, if we have just send data from
891 * xmit->tail to the end of xmit->buf, now we have to transmit the
892 * remaining data from the beginning of xmit->buf to xmit->head.
893 */
894 if (!uart_circ_empty(xmit))
895 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
896 else if (atmel_uart_is_half_duplex(port)) {
897 /*
898 * DMA done, re-enable TXEMPTY and signal that we can stop
899 * TX and start RX for RS485
900 */
901 atmel_port->hd_start_rx = true;
902 atmel_uart_writel(port, ATMEL_US_IER,
903 atmel_port->tx_done_mask);
904 }
905
906 spin_unlock_irqrestore(&port->lock, flags);
907}
908
909static void atmel_release_tx_dma(struct uart_port *port)
910{
911 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
912 struct dma_chan *chan = atmel_port->chan_tx;
913
914 if (chan) {
915 dmaengine_terminate_all(chan);
916 dma_release_channel(chan);
917 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1,
918 DMA_TO_DEVICE);
919 }
920
921 atmel_port->desc_tx = NULL;
922 atmel_port->chan_tx = NULL;
923 atmel_port->cookie_tx = -EINVAL;
924}
925
926/*
927 * Called from tasklet with TXRDY interrupt is disabled.
928 */
929static void atmel_tx_dma(struct uart_port *port)
930{
931 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
932 struct circ_buf *xmit = &port->state->xmit;
933 struct dma_chan *chan = atmel_port->chan_tx;
934 struct dma_async_tx_descriptor *desc;
935 struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx;
936 unsigned int tx_len, part1_len, part2_len, sg_len;
937 dma_addr_t phys_addr;
938
939 /* Make sure we have an idle channel */
940 if (atmel_port->desc_tx != NULL)
941 return;
942
943 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
944 /*
945 * DMA is idle now.
946 * Port xmit buffer is already mapped,
947 * and it is one page... Just adjust
948 * offsets and lengths. Since it is a circular buffer,
949 * we have to transmit till the end, and then the rest.
950 * Take the port lock to get a
951 * consistent xmit buffer state.
952 */
953 tx_len = CIRC_CNT_TO_END(xmit->head,
954 xmit->tail,
955 UART_XMIT_SIZE);
956
957 if (atmel_port->fifo_size) {
958 /* multi data mode */
959 part1_len = (tx_len & ~0x3); /* DWORD access */
960 part2_len = (tx_len & 0x3); /* BYTE access */
961 } else {
962 /* single data (legacy) mode */
963 part1_len = 0;
964 part2_len = tx_len; /* BYTE access only */
965 }
966
967 sg_init_table(sgl, 2);
968 sg_len = 0;
969 phys_addr = sg_dma_address(sg_tx) + xmit->tail;
970 if (part1_len) {
971 sg = &sgl[sg_len++];
972 sg_dma_address(sg) = phys_addr;
973 sg_dma_len(sg) = part1_len;
974
975 phys_addr += part1_len;
976 }
977
978 if (part2_len) {
979 sg = &sgl[sg_len++];
980 sg_dma_address(sg) = phys_addr;
981 sg_dma_len(sg) = part2_len;
982 }
983
984 /*
985 * save tx_len so atmel_complete_tx_dma() will increase
986 * xmit->tail correctly
987 */
988 atmel_port->tx_len = tx_len;
989
990 desc = dmaengine_prep_slave_sg(chan,
991 sgl,
992 sg_len,
993 DMA_MEM_TO_DEV,
994 DMA_PREP_INTERRUPT |
995 DMA_CTRL_ACK);
996 if (!desc) {
997 dev_err(port->dev, "Failed to send via dma!\n");
998 return;
999 }
1000
1001 dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE);
1002
1003 atmel_port->desc_tx = desc;
1004 desc->callback = atmel_complete_tx_dma;
1005 desc->callback_param = atmel_port;
1006 atmel_port->cookie_tx = dmaengine_submit(desc);
1007 }
1008
1009 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1010 uart_write_wakeup(port);
1011}
1012
1013static int atmel_prepare_tx_dma(struct uart_port *port)
1014{
1015 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1016 struct device *mfd_dev = port->dev->parent;
1017 dma_cap_mask_t mask;
1018 struct dma_slave_config config;
1019 int ret, nent;
1020
1021 dma_cap_zero(mask);
1022 dma_cap_set(DMA_SLAVE, mask);
1023
1024 atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
1025 if (atmel_port->chan_tx == NULL)
1026 goto chan_err;
1027 dev_info(port->dev, "using %s for tx DMA transfers\n",
1028 dma_chan_name(atmel_port->chan_tx));
1029
1030 spin_lock_init(&atmel_port->lock_tx);
1031 sg_init_table(&atmel_port->sg_tx, 1);
1032 /* UART circular tx buffer is an aligned page. */
1033 BUG_ON(!PAGE_ALIGNED(port->state->xmit.buf));
1034 sg_set_page(&atmel_port->sg_tx,
1035 virt_to_page(port->state->xmit.buf),
1036 UART_XMIT_SIZE,
1037 offset_in_page(port->state->xmit.buf));
1038 nent = dma_map_sg(port->dev,
1039 &atmel_port->sg_tx,
1040 1,
1041 DMA_TO_DEVICE);
1042
1043 if (!nent) {
1044 dev_dbg(port->dev, "need to release resource of dma\n");
1045 goto chan_err;
1046 } else {
1047 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1048 sg_dma_len(&atmel_port->sg_tx),
1049 port->state->xmit.buf,
1050 &sg_dma_address(&atmel_port->sg_tx));
1051 }
1052
1053 /* Configure the slave DMA */
1054 memset(&config, 0, sizeof(config));
1055 config.direction = DMA_MEM_TO_DEV;
1056 config.dst_addr_width = (atmel_port->fifo_size) ?
1057 DMA_SLAVE_BUSWIDTH_4_BYTES :
1058 DMA_SLAVE_BUSWIDTH_1_BYTE;
1059 config.dst_addr = port->mapbase + ATMEL_US_THR;
1060 config.dst_maxburst = 1;
1061
1062 ret = dmaengine_slave_config(atmel_port->chan_tx,
1063 &config);
1064 if (ret) {
1065 dev_err(port->dev, "DMA tx slave configuration failed\n");
1066 goto chan_err;
1067 }
1068
1069 return 0;
1070
1071chan_err:
1072 dev_err(port->dev, "TX channel not available, switch to pio\n");
1073 atmel_port->use_dma_tx = false;
1074 if (atmel_port->chan_tx)
1075 atmel_release_tx_dma(port);
1076 return -EINVAL;
1077}
1078
1079static void atmel_complete_rx_dma(void *arg)
1080{
1081 struct uart_port *port = arg;
1082 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1083
1084 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1085}
1086
1087static void atmel_release_rx_dma(struct uart_port *port)
1088{
1089 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1090 struct dma_chan *chan = atmel_port->chan_rx;
1091
1092 if (chan) {
1093 dmaengine_terminate_all(chan);
1094 dma_release_channel(chan);
1095 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1,
1096 DMA_FROM_DEVICE);
1097 }
1098
1099 atmel_port->desc_rx = NULL;
1100 atmel_port->chan_rx = NULL;
1101 atmel_port->cookie_rx = -EINVAL;
1102}
1103
1104static void atmel_rx_from_dma(struct uart_port *port)
1105{
1106 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1107 struct tty_port *tport = &port->state->port;
1108 struct circ_buf *ring = &atmel_port->rx_ring;
1109 struct dma_chan *chan = atmel_port->chan_rx;
1110 struct dma_tx_state state;
1111 enum dma_status dmastat;
1112 size_t count;
1113
1114
1115 /* Reset the UART timeout early so that we don't miss one */
1116 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1117 dmastat = dmaengine_tx_status(chan,
1118 atmel_port->cookie_rx,
1119 &state);
1120 /* Restart a new tasklet if DMA status is error */
1121 if (dmastat == DMA_ERROR) {
1122 dev_dbg(port->dev, "Get residue error, restart tasklet\n");
1123 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1124 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1125 return;
1126 }
1127
1128 /* CPU claims ownership of RX DMA buffer */
1129 dma_sync_sg_for_cpu(port->dev,
1130 &atmel_port->sg_rx,
1131 1,
1132 DMA_FROM_DEVICE);
1133
1134 /*
1135 * ring->head points to the end of data already written by the DMA.
1136 * ring->tail points to the beginning of data to be read by the
1137 * framework.
1138 * The current transfer size should not be larger than the dma buffer
1139 * length.
1140 */
1141 ring->head = sg_dma_len(&atmel_port->sg_rx) - state.residue;
1142 BUG_ON(ring->head > sg_dma_len(&atmel_port->sg_rx));
1143 /*
1144 * At this point ring->head may point to the first byte right after the
1145 * last byte of the dma buffer:
1146 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx)
1147 *
1148 * However ring->tail must always points inside the dma buffer:
1149 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1
1150 *
1151 * Since we use a ring buffer, we have to handle the case
1152 * where head is lower than tail. In such a case, we first read from
1153 * tail to the end of the buffer then reset tail.
1154 */
1155 if (ring->head < ring->tail) {
1156 count = sg_dma_len(&atmel_port->sg_rx) - ring->tail;
1157
1158 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1159 ring->tail = 0;
1160 port->icount.rx += count;
1161 }
1162
1163 /* Finally we read data from tail to head */
1164 if (ring->tail < ring->head) {
1165 count = ring->head - ring->tail;
1166
1167 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1168 /* Wrap ring->head if needed */
1169 if (ring->head >= sg_dma_len(&atmel_port->sg_rx))
1170 ring->head = 0;
1171 ring->tail = ring->head;
1172 port->icount.rx += count;
1173 }
1174
1175 /* USART retreives ownership of RX DMA buffer */
1176 dma_sync_sg_for_device(port->dev,
1177 &atmel_port->sg_rx,
1178 1,
1179 DMA_FROM_DEVICE);
1180
1181 tty_flip_buffer_push(tport);
1182
1183 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1184}
1185
1186static int atmel_prepare_rx_dma(struct uart_port *port)
1187{
1188 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1189 struct device *mfd_dev = port->dev->parent;
1190 struct dma_async_tx_descriptor *desc;
1191 dma_cap_mask_t mask;
1192 struct dma_slave_config config;
1193 struct circ_buf *ring;
1194 int ret, nent;
1195
1196 ring = &atmel_port->rx_ring;
1197
1198 dma_cap_zero(mask);
1199 dma_cap_set(DMA_CYCLIC, mask);
1200
1201 atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
1202 if (atmel_port->chan_rx == NULL)
1203 goto chan_err;
1204 dev_info(port->dev, "using %s for rx DMA transfers\n",
1205 dma_chan_name(atmel_port->chan_rx));
1206
1207 spin_lock_init(&atmel_port->lock_rx);
1208 sg_init_table(&atmel_port->sg_rx, 1);
1209 /* UART circular rx buffer is an aligned page. */
1210 BUG_ON(!PAGE_ALIGNED(ring->buf));
1211 sg_set_page(&atmel_port->sg_rx,
1212 virt_to_page(ring->buf),
1213 sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE,
1214 offset_in_page(ring->buf));
1215 nent = dma_map_sg(port->dev,
1216 &atmel_port->sg_rx,
1217 1,
1218 DMA_FROM_DEVICE);
1219
1220 if (!nent) {
1221 dev_dbg(port->dev, "need to release resource of dma\n");
1222 goto chan_err;
1223 } else {
1224 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1225 sg_dma_len(&atmel_port->sg_rx),
1226 ring->buf,
1227 &sg_dma_address(&atmel_port->sg_rx));
1228 }
1229
1230 /* Configure the slave DMA */
1231 memset(&config, 0, sizeof(config));
1232 config.direction = DMA_DEV_TO_MEM;
1233 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1234 config.src_addr = port->mapbase + ATMEL_US_RHR;
1235 config.src_maxburst = 1;
1236
1237 ret = dmaengine_slave_config(atmel_port->chan_rx,
1238 &config);
1239 if (ret) {
1240 dev_err(port->dev, "DMA rx slave configuration failed\n");
1241 goto chan_err;
1242 }
1243 /*
1244 * Prepare a cyclic dma transfer, assign 2 descriptors,
1245 * each one is half ring buffer size
1246 */
1247 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx,
1248 sg_dma_address(&atmel_port->sg_rx),
1249 sg_dma_len(&atmel_port->sg_rx),
1250 sg_dma_len(&atmel_port->sg_rx)/2,
1251 DMA_DEV_TO_MEM,
1252 DMA_PREP_INTERRUPT);
1253 if (!desc) {
1254 dev_err(port->dev, "Preparing DMA cyclic failed\n");
1255 goto chan_err;
1256 }
1257 desc->callback = atmel_complete_rx_dma;
1258 desc->callback_param = port;
1259 atmel_port->desc_rx = desc;
1260 atmel_port->cookie_rx = dmaengine_submit(desc);
1261
1262 return 0;
1263
1264chan_err:
1265 dev_err(port->dev, "RX channel not available, switch to pio\n");
1266 atmel_port->use_dma_rx = false;
1267 if (atmel_port->chan_rx)
1268 atmel_release_rx_dma(port);
1269 return -EINVAL;
1270}
1271
1272static void atmel_uart_timer_callback(struct timer_list *t)
1273{
1274 struct atmel_uart_port *atmel_port = from_timer(atmel_port, t,
1275 uart_timer);
1276 struct uart_port *port = &atmel_port->uart;
1277
1278 if (!atomic_read(&atmel_port->tasklet_shutdown)) {
1279 tasklet_schedule(&atmel_port->tasklet_rx);
1280 mod_timer(&atmel_port->uart_timer,
1281 jiffies + uart_poll_timeout(port));
1282 }
1283}
1284
1285/*
1286 * receive interrupt handler.
1287 */
1288static void
1289atmel_handle_receive(struct uart_port *port, unsigned int pending)
1290{
1291 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1292
1293 if (atmel_use_pdc_rx(port)) {
1294 /*
1295 * PDC receive. Just schedule the tasklet and let it
1296 * figure out the details.
1297 *
1298 * TODO: We're not handling error flags correctly at
1299 * the moment.
1300 */
1301 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
1302 atmel_uart_writel(port, ATMEL_US_IDR,
1303 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT));
1304 atmel_tasklet_schedule(atmel_port,
1305 &atmel_port->tasklet_rx);
1306 }
1307
1308 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
1309 ATMEL_US_FRAME | ATMEL_US_PARE))
1310 atmel_pdc_rxerr(port, pending);
1311 }
1312
1313 if (atmel_use_dma_rx(port)) {
1314 if (pending & ATMEL_US_TIMEOUT) {
1315 atmel_uart_writel(port, ATMEL_US_IDR,
1316 ATMEL_US_TIMEOUT);
1317 atmel_tasklet_schedule(atmel_port,
1318 &atmel_port->tasklet_rx);
1319 }
1320 }
1321
1322 /* Interrupt receive */
1323 if (pending & ATMEL_US_RXRDY)
1324 atmel_rx_chars(port);
1325 else if (pending & ATMEL_US_RXBRK) {
1326 /*
1327 * End of break detected. If it came along with a
1328 * character, atmel_rx_chars will handle it.
1329 */
1330 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
1331 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK);
1332 atmel_port->break_active = 0;
1333 }
1334}
1335
1336/*
1337 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
1338 */
1339static void
1340atmel_handle_transmit(struct uart_port *port, unsigned int pending)
1341{
1342 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1343
1344 if (pending & atmel_port->tx_done_mask) {
1345 atmel_uart_writel(port, ATMEL_US_IDR,
1346 atmel_port->tx_done_mask);
1347
1348 /* Start RX if flag was set and FIFO is empty */
1349 if (atmel_port->hd_start_rx) {
1350 if (!(atmel_uart_readl(port, ATMEL_US_CSR)
1351 & ATMEL_US_TXEMPTY))
1352 dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
1353
1354 atmel_port->hd_start_rx = false;
1355 atmel_start_rx(port);
1356 }
1357
1358 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
1359 }
1360}
1361
1362/*
1363 * status flags interrupt handler.
1364 */
1365static void
1366atmel_handle_status(struct uart_port *port, unsigned int pending,
1367 unsigned int status)
1368{
1369 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1370 unsigned int status_change;
1371
1372 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
1373 | ATMEL_US_CTSIC)) {
1374 status_change = status ^ atmel_port->irq_status_prev;
1375 atmel_port->irq_status_prev = status;
1376
1377 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
1378 | ATMEL_US_DCD | ATMEL_US_CTS)) {
1379 /* TODO: All reads to CSR will clear these interrupts! */
1380 if (status_change & ATMEL_US_RI)
1381 port->icount.rng++;
1382 if (status_change & ATMEL_US_DSR)
1383 port->icount.dsr++;
1384 if (status_change & ATMEL_US_DCD)
1385 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
1386 if (status_change & ATMEL_US_CTS)
1387 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
1388
1389 wake_up_interruptible(&port->state->port.delta_msr_wait);
1390 }
1391 }
1392
1393 if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION))
1394 dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending);
1395}
1396
1397/*
1398 * Interrupt handler
1399 */
1400static irqreturn_t atmel_interrupt(int irq, void *dev_id)
1401{
1402 struct uart_port *port = dev_id;
1403 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1404 unsigned int status, pending, mask, pass_counter = 0;
1405
1406 spin_lock(&atmel_port->lock_suspended);
1407
1408 do {
1409 status = atmel_uart_readl(port, ATMEL_US_CSR);
1410 mask = atmel_uart_readl(port, ATMEL_US_IMR);
1411 pending = status & mask;
1412 if (!pending)
1413 break;
1414
1415 if (atmel_port->suspended) {
1416 atmel_port->pending |= pending;
1417 atmel_port->pending_status = status;
1418 atmel_uart_writel(port, ATMEL_US_IDR, mask);
1419 pm_system_wakeup();
1420 break;
1421 }
1422
1423 atmel_handle_receive(port, pending);
1424 atmel_handle_status(port, pending, status);
1425 atmel_handle_transmit(port, pending);
1426 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
1427
1428 spin_unlock(&atmel_port->lock_suspended);
1429
1430 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
1431}
1432
1433static void atmel_release_tx_pdc(struct uart_port *port)
1434{
1435 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1436 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1437
1438 dma_unmap_single(port->dev,
1439 pdc->dma_addr,
1440 pdc->dma_size,
1441 DMA_TO_DEVICE);
1442}
1443
1444/*
1445 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
1446 */
1447static void atmel_tx_pdc(struct uart_port *port)
1448{
1449 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1450 struct circ_buf *xmit = &port->state->xmit;
1451 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1452 int count;
1453
1454 /* nothing left to transmit? */
1455 if (atmel_uart_readl(port, ATMEL_PDC_TCR))
1456 return;
1457
1458 xmit->tail += pdc->ofs;
1459 xmit->tail &= UART_XMIT_SIZE - 1;
1460
1461 port->icount.tx += pdc->ofs;
1462 pdc->ofs = 0;
1463
1464 /* more to transmit - setup next transfer */
1465
1466 /* disable PDC transmit */
1467 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
1468
1469 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
1470 dma_sync_single_for_device(port->dev,
1471 pdc->dma_addr,
1472 pdc->dma_size,
1473 DMA_TO_DEVICE);
1474
1475 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
1476 pdc->ofs = count;
1477
1478 atmel_uart_writel(port, ATMEL_PDC_TPR,
1479 pdc->dma_addr + xmit->tail);
1480 atmel_uart_writel(port, ATMEL_PDC_TCR, count);
1481 /* re-enable PDC transmit */
1482 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1483 /* Enable interrupts */
1484 atmel_uart_writel(port, ATMEL_US_IER,
1485 atmel_port->tx_done_mask);
1486 } else {
1487 if (atmel_uart_is_half_duplex(port)) {
1488 /* DMA done, stop TX, start RX for RS485 */
1489 atmel_start_rx(port);
1490 }
1491 }
1492
1493 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1494 uart_write_wakeup(port);
1495}
1496
1497static int atmel_prepare_tx_pdc(struct uart_port *port)
1498{
1499 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1500 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1501 struct circ_buf *xmit = &port->state->xmit;
1502
1503 pdc->buf = xmit->buf;
1504 pdc->dma_addr = dma_map_single(port->dev,
1505 pdc->buf,
1506 UART_XMIT_SIZE,
1507 DMA_TO_DEVICE);
1508 pdc->dma_size = UART_XMIT_SIZE;
1509 pdc->ofs = 0;
1510
1511 return 0;
1512}
1513
1514static void atmel_rx_from_ring(struct uart_port *port)
1515{
1516 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1517 struct circ_buf *ring = &atmel_port->rx_ring;
1518 unsigned int flg;
1519 unsigned int status;
1520
1521 while (ring->head != ring->tail) {
1522 struct atmel_uart_char c;
1523
1524 /* Make sure c is loaded after head. */
1525 smp_rmb();
1526
1527 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
1528
1529 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
1530
1531 port->icount.rx++;
1532 status = c.status;
1533 flg = TTY_NORMAL;
1534
1535 /*
1536 * note that the error handling code is
1537 * out of the main execution path
1538 */
1539 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
1540 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
1541 if (status & ATMEL_US_RXBRK) {
1542 /* ignore side-effect */
1543 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
1544
1545 port->icount.brk++;
1546 if (uart_handle_break(port))
1547 continue;
1548 }
1549 if (status & ATMEL_US_PARE)
1550 port->icount.parity++;
1551 if (status & ATMEL_US_FRAME)
1552 port->icount.frame++;
1553 if (status & ATMEL_US_OVRE)
1554 port->icount.overrun++;
1555
1556 status &= port->read_status_mask;
1557
1558 if (status & ATMEL_US_RXBRK)
1559 flg = TTY_BREAK;
1560 else if (status & ATMEL_US_PARE)
1561 flg = TTY_PARITY;
1562 else if (status & ATMEL_US_FRAME)
1563 flg = TTY_FRAME;
1564 }
1565
1566
1567 if (uart_handle_sysrq_char(port, c.ch))
1568 continue;
1569
1570 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
1571 }
1572
1573 tty_flip_buffer_push(&port->state->port);
1574}
1575
1576static void atmel_release_rx_pdc(struct uart_port *port)
1577{
1578 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1579 int i;
1580
1581 for (i = 0; i < 2; i++) {
1582 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1583
1584 dma_unmap_single(port->dev,
1585 pdc->dma_addr,
1586 pdc->dma_size,
1587 DMA_FROM_DEVICE);
1588 kfree(pdc->buf);
1589 }
1590}
1591
1592static void atmel_rx_from_pdc(struct uart_port *port)
1593{
1594 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1595 struct tty_port *tport = &port->state->port;
1596 struct atmel_dma_buffer *pdc;
1597 int rx_idx = atmel_port->pdc_rx_idx;
1598 unsigned int head;
1599 unsigned int tail;
1600 unsigned int count;
1601
1602 do {
1603 /* Reset the UART timeout early so that we don't miss one */
1604 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1605
1606 pdc = &atmel_port->pdc_rx[rx_idx];
1607 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr;
1608 tail = pdc->ofs;
1609
1610 /* If the PDC has switched buffers, RPR won't contain
1611 * any address within the current buffer. Since head
1612 * is unsigned, we just need a one-way comparison to
1613 * find out.
1614 *
1615 * In this case, we just need to consume the entire
1616 * buffer and resubmit it for DMA. This will clear the
1617 * ENDRX bit as well, so that we can safely re-enable
1618 * all interrupts below.
1619 */
1620 head = min(head, pdc->dma_size);
1621
1622 if (likely(head != tail)) {
1623 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
1624 pdc->dma_size, DMA_FROM_DEVICE);
1625
1626 /*
1627 * head will only wrap around when we recycle
1628 * the DMA buffer, and when that happens, we
1629 * explicitly set tail to 0. So head will
1630 * always be greater than tail.
1631 */
1632 count = head - tail;
1633
1634 tty_insert_flip_string(tport, pdc->buf + pdc->ofs,
1635 count);
1636
1637 dma_sync_single_for_device(port->dev, pdc->dma_addr,
1638 pdc->dma_size, DMA_FROM_DEVICE);
1639
1640 port->icount.rx += count;
1641 pdc->ofs = head;
1642 }
1643
1644 /*
1645 * If the current buffer is full, we need to check if
1646 * the next one contains any additional data.
1647 */
1648 if (head >= pdc->dma_size) {
1649 pdc->ofs = 0;
1650 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr);
1651 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size);
1652
1653 rx_idx = !rx_idx;
1654 atmel_port->pdc_rx_idx = rx_idx;
1655 }
1656 } while (head >= pdc->dma_size);
1657
1658 tty_flip_buffer_push(tport);
1659
1660 atmel_uart_writel(port, ATMEL_US_IER,
1661 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1662}
1663
1664static int atmel_prepare_rx_pdc(struct uart_port *port)
1665{
1666 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1667 int i;
1668
1669 for (i = 0; i < 2; i++) {
1670 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1671
1672 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
1673 if (pdc->buf == NULL) {
1674 if (i != 0) {
1675 dma_unmap_single(port->dev,
1676 atmel_port->pdc_rx[0].dma_addr,
1677 PDC_BUFFER_SIZE,
1678 DMA_FROM_DEVICE);
1679 kfree(atmel_port->pdc_rx[0].buf);
1680 }
1681 atmel_port->use_pdc_rx = false;
1682 return -ENOMEM;
1683 }
1684 pdc->dma_addr = dma_map_single(port->dev,
1685 pdc->buf,
1686 PDC_BUFFER_SIZE,
1687 DMA_FROM_DEVICE);
1688 pdc->dma_size = PDC_BUFFER_SIZE;
1689 pdc->ofs = 0;
1690 }
1691
1692 atmel_port->pdc_rx_idx = 0;
1693
1694 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr);
1695 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE);
1696
1697 atmel_uart_writel(port, ATMEL_PDC_RNPR,
1698 atmel_port->pdc_rx[1].dma_addr);
1699 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE);
1700
1701 return 0;
1702}
1703
1704/*
1705 * tasklet handling tty stuff outside the interrupt handler.
1706 */
1707static void atmel_tasklet_rx_func(struct tasklet_struct *t)
1708{
1709 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t,
1710 tasklet_rx);
1711 struct uart_port *port = &atmel_port->uart;
1712
1713 /* The interrupt handler does not take the lock */
1714 spin_lock(&port->lock);
1715 atmel_port->schedule_rx(port);
1716 spin_unlock(&port->lock);
1717}
1718
1719static void atmel_tasklet_tx_func(struct tasklet_struct *t)
1720{
1721 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t,
1722 tasklet_tx);
1723 struct uart_port *port = &atmel_port->uart;
1724
1725 /* The interrupt handler does not take the lock */
1726 spin_lock(&port->lock);
1727 atmel_port->schedule_tx(port);
1728 spin_unlock(&port->lock);
1729}
1730
1731static void atmel_init_property(struct atmel_uart_port *atmel_port,
1732 struct platform_device *pdev)
1733{
1734 struct device_node *np = pdev->dev.of_node;
1735
1736 /* DMA/PDC usage specification */
1737 if (of_property_read_bool(np, "atmel,use-dma-rx")) {
1738 if (of_property_read_bool(np, "dmas")) {
1739 atmel_port->use_dma_rx = true;
1740 atmel_port->use_pdc_rx = false;
1741 } else {
1742 atmel_port->use_dma_rx = false;
1743 atmel_port->use_pdc_rx = true;
1744 }
1745 } else {
1746 atmel_port->use_dma_rx = false;
1747 atmel_port->use_pdc_rx = false;
1748 }
1749
1750 if (of_property_read_bool(np, "atmel,use-dma-tx")) {
1751 if (of_property_read_bool(np, "dmas")) {
1752 atmel_port->use_dma_tx = true;
1753 atmel_port->use_pdc_tx = false;
1754 } else {
1755 atmel_port->use_dma_tx = false;
1756 atmel_port->use_pdc_tx = true;
1757 }
1758 } else {
1759 atmel_port->use_dma_tx = false;
1760 atmel_port->use_pdc_tx = false;
1761 }
1762}
1763
1764static void atmel_set_ops(struct uart_port *port)
1765{
1766 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1767
1768 if (atmel_use_dma_rx(port)) {
1769 atmel_port->prepare_rx = &atmel_prepare_rx_dma;
1770 atmel_port->schedule_rx = &atmel_rx_from_dma;
1771 atmel_port->release_rx = &atmel_release_rx_dma;
1772 } else if (atmel_use_pdc_rx(port)) {
1773 atmel_port->prepare_rx = &atmel_prepare_rx_pdc;
1774 atmel_port->schedule_rx = &atmel_rx_from_pdc;
1775 atmel_port->release_rx = &atmel_release_rx_pdc;
1776 } else {
1777 atmel_port->prepare_rx = NULL;
1778 atmel_port->schedule_rx = &atmel_rx_from_ring;
1779 atmel_port->release_rx = NULL;
1780 }
1781
1782 if (atmel_use_dma_tx(port)) {
1783 atmel_port->prepare_tx = &atmel_prepare_tx_dma;
1784 atmel_port->schedule_tx = &atmel_tx_dma;
1785 atmel_port->release_tx = &atmel_release_tx_dma;
1786 } else if (atmel_use_pdc_tx(port)) {
1787 atmel_port->prepare_tx = &atmel_prepare_tx_pdc;
1788 atmel_port->schedule_tx = &atmel_tx_pdc;
1789 atmel_port->release_tx = &atmel_release_tx_pdc;
1790 } else {
1791 atmel_port->prepare_tx = NULL;
1792 atmel_port->schedule_tx = &atmel_tx_chars;
1793 atmel_port->release_tx = NULL;
1794 }
1795}
1796
1797/*
1798 * Get ip name usart or uart
1799 */
1800static void atmel_get_ip_name(struct uart_port *port)
1801{
1802 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1803 int name = atmel_uart_readl(port, ATMEL_US_NAME);
1804 u32 version;
1805 u32 usart, dbgu_uart, new_uart;
1806 /* ASCII decoding for IP version */
1807 usart = 0x55534152; /* USAR(T) */
1808 dbgu_uart = 0x44424755; /* DBGU */
1809 new_uart = 0x55415254; /* UART */
1810
1811 /*
1812 * Only USART devices from at91sam9260 SOC implement fractional
1813 * baudrate. It is available for all asynchronous modes, with the
1814 * following restriction: the sampling clock's duty cycle is not
1815 * constant.
1816 */
1817 atmel_port->has_frac_baudrate = false;
1818 atmel_port->has_hw_timer = false;
1819
1820 if (name == new_uart) {
1821 dev_dbg(port->dev, "Uart with hw timer");
1822 atmel_port->has_hw_timer = true;
1823 atmel_port->rtor = ATMEL_UA_RTOR;
1824 } else if (name == usart) {
1825 dev_dbg(port->dev, "Usart\n");
1826 atmel_port->has_frac_baudrate = true;
1827 atmel_port->has_hw_timer = true;
1828 atmel_port->rtor = ATMEL_US_RTOR;
1829 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1830 switch (version) {
1831 case 0x814: /* sama5d2 */
1832 fallthrough;
1833 case 0x701: /* sama5d4 */
1834 atmel_port->fidi_min = 3;
1835 atmel_port->fidi_max = 65535;
1836 break;
1837 case 0x502: /* sam9x5, sama5d3 */
1838 atmel_port->fidi_min = 3;
1839 atmel_port->fidi_max = 2047;
1840 break;
1841 default:
1842 atmel_port->fidi_min = 1;
1843 atmel_port->fidi_max = 2047;
1844 }
1845 } else if (name == dbgu_uart) {
1846 dev_dbg(port->dev, "Dbgu or uart without hw timer\n");
1847 } else {
1848 /* fallback for older SoCs: use version field */
1849 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1850 switch (version) {
1851 case 0x302:
1852 case 0x10213:
1853 case 0x10302:
1854 dev_dbg(port->dev, "This version is usart\n");
1855 atmel_port->has_frac_baudrate = true;
1856 atmel_port->has_hw_timer = true;
1857 atmel_port->rtor = ATMEL_US_RTOR;
1858 break;
1859 case 0x203:
1860 case 0x10202:
1861 dev_dbg(port->dev, "This version is uart\n");
1862 break;
1863 default:
1864 dev_err(port->dev, "Not supported ip name nor version, set to uart\n");
1865 }
1866 }
1867}
1868
1869/*
1870 * Perform initialization and enable port for reception
1871 */
1872static int atmel_startup(struct uart_port *port)
1873{
1874 struct platform_device *pdev = to_platform_device(port->dev);
1875 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1876 int retval;
1877
1878 /*
1879 * Ensure that no interrupts are enabled otherwise when
1880 * request_irq() is called we could get stuck trying to
1881 * handle an unexpected interrupt
1882 */
1883 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1884 atmel_port->ms_irq_enabled = false;
1885
1886 /*
1887 * Allocate the IRQ
1888 */
1889 retval = request_irq(port->irq, atmel_interrupt,
1890 IRQF_SHARED | IRQF_COND_SUSPEND,
1891 dev_name(&pdev->dev), port);
1892 if (retval) {
1893 dev_err(port->dev, "atmel_startup - Can't get irq\n");
1894 return retval;
1895 }
1896
1897 atomic_set(&atmel_port->tasklet_shutdown, 0);
1898 tasklet_setup(&atmel_port->tasklet_rx, atmel_tasklet_rx_func);
1899 tasklet_setup(&atmel_port->tasklet_tx, atmel_tasklet_tx_func);
1900
1901 /*
1902 * Initialize DMA (if necessary)
1903 */
1904 atmel_init_property(atmel_port, pdev);
1905 atmel_set_ops(port);
1906
1907 if (atmel_port->prepare_rx) {
1908 retval = atmel_port->prepare_rx(port);
1909 if (retval < 0)
1910 atmel_set_ops(port);
1911 }
1912
1913 if (atmel_port->prepare_tx) {
1914 retval = atmel_port->prepare_tx(port);
1915 if (retval < 0)
1916 atmel_set_ops(port);
1917 }
1918
1919 /*
1920 * Enable FIFO when available
1921 */
1922 if (atmel_port->fifo_size) {
1923 unsigned int txrdym = ATMEL_US_ONE_DATA;
1924 unsigned int rxrdym = ATMEL_US_ONE_DATA;
1925 unsigned int fmr;
1926
1927 atmel_uart_writel(port, ATMEL_US_CR,
1928 ATMEL_US_FIFOEN |
1929 ATMEL_US_RXFCLR |
1930 ATMEL_US_TXFLCLR);
1931
1932 if (atmel_use_dma_tx(port))
1933 txrdym = ATMEL_US_FOUR_DATA;
1934
1935 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym);
1936 if (atmel_port->rts_high &&
1937 atmel_port->rts_low)
1938 fmr |= ATMEL_US_FRTSC |
1939 ATMEL_US_RXFTHRES(atmel_port->rts_high) |
1940 ATMEL_US_RXFTHRES2(atmel_port->rts_low);
1941
1942 atmel_uart_writel(port, ATMEL_US_FMR, fmr);
1943 }
1944
1945 /* Save current CSR for comparison in atmel_tasklet_func() */
1946 atmel_port->irq_status_prev = atmel_uart_readl(port, ATMEL_US_CSR);
1947
1948 /*
1949 * Finally, enable the serial port
1950 */
1951 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1952 /* enable xmit & rcvr */
1953 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
1954 atmel_port->tx_stopped = false;
1955
1956 timer_setup(&atmel_port->uart_timer, atmel_uart_timer_callback, 0);
1957
1958 if (atmel_use_pdc_rx(port)) {
1959 /* set UART timeout */
1960 if (!atmel_port->has_hw_timer) {
1961 mod_timer(&atmel_port->uart_timer,
1962 jiffies + uart_poll_timeout(port));
1963 /* set USART timeout */
1964 } else {
1965 atmel_uart_writel(port, atmel_port->rtor,
1966 PDC_RX_TIMEOUT);
1967 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1968
1969 atmel_uart_writel(port, ATMEL_US_IER,
1970 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1971 }
1972 /* enable PDC controller */
1973 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1974 } else if (atmel_use_dma_rx(port)) {
1975 /* set UART timeout */
1976 if (!atmel_port->has_hw_timer) {
1977 mod_timer(&atmel_port->uart_timer,
1978 jiffies + uart_poll_timeout(port));
1979 /* set USART timeout */
1980 } else {
1981 atmel_uart_writel(port, atmel_port->rtor,
1982 PDC_RX_TIMEOUT);
1983 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1984
1985 atmel_uart_writel(port, ATMEL_US_IER,
1986 ATMEL_US_TIMEOUT);
1987 }
1988 } else {
1989 /* enable receive only */
1990 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
1991 }
1992
1993 return 0;
1994}
1995
1996/*
1997 * Flush any TX data submitted for DMA. Called when the TX circular
1998 * buffer is reset.
1999 */
2000static void atmel_flush_buffer(struct uart_port *port)
2001{
2002 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2003
2004 if (atmel_use_pdc_tx(port)) {
2005 atmel_uart_writel(port, ATMEL_PDC_TCR, 0);
2006 atmel_port->pdc_tx.ofs = 0;
2007 }
2008 /*
2009 * in uart_flush_buffer(), the xmit circular buffer has just
2010 * been cleared, so we have to reset tx_len accordingly.
2011 */
2012 atmel_port->tx_len = 0;
2013}
2014
2015/*
2016 * Disable the port
2017 */
2018static void atmel_shutdown(struct uart_port *port)
2019{
2020 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2021
2022 /* Disable modem control lines interrupts */
2023 atmel_disable_ms(port);
2024
2025 /* Disable interrupts at device level */
2026 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2027
2028 /* Prevent spurious interrupts from scheduling the tasklet */
2029 atomic_inc(&atmel_port->tasklet_shutdown);
2030
2031 /*
2032 * Prevent any tasklets being scheduled during
2033 * cleanup
2034 */
2035 del_timer_sync(&atmel_port->uart_timer);
2036
2037 /* Make sure that no interrupt is on the fly */
2038 synchronize_irq(port->irq);
2039
2040 /*
2041 * Clear out any scheduled tasklets before
2042 * we destroy the buffers
2043 */
2044 tasklet_kill(&atmel_port->tasklet_rx);
2045 tasklet_kill(&atmel_port->tasklet_tx);
2046
2047 /*
2048 * Ensure everything is stopped and
2049 * disable port and break condition.
2050 */
2051 atmel_stop_rx(port);
2052 atmel_stop_tx(port);
2053
2054 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
2055
2056 /*
2057 * Shut-down the DMA.
2058 */
2059 if (atmel_port->release_rx)
2060 atmel_port->release_rx(port);
2061 if (atmel_port->release_tx)
2062 atmel_port->release_tx(port);
2063
2064 /*
2065 * Reset ring buffer pointers
2066 */
2067 atmel_port->rx_ring.head = 0;
2068 atmel_port->rx_ring.tail = 0;
2069
2070 /*
2071 * Free the interrupts
2072 */
2073 free_irq(port->irq, port);
2074
2075 atmel_flush_buffer(port);
2076}
2077
2078/*
2079 * Power / Clock management.
2080 */
2081static void atmel_serial_pm(struct uart_port *port, unsigned int state,
2082 unsigned int oldstate)
2083{
2084 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2085
2086 switch (state) {
2087 case 0:
2088 /*
2089 * Enable the peripheral clock for this serial port.
2090 * This is called on uart_open() or a resume event.
2091 */
2092 clk_prepare_enable(atmel_port->clk);
2093
2094 /* re-enable interrupts if we disabled some on suspend */
2095 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr);
2096 break;
2097 case 3:
2098 /* Back up the interrupt mask and disable all interrupts */
2099 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR);
2100 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2101
2102 /*
2103 * Disable the peripheral clock for this serial port.
2104 * This is called on uart_close() or a suspend event.
2105 */
2106 clk_disable_unprepare(atmel_port->clk);
2107 break;
2108 default:
2109 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
2110 }
2111}
2112
2113/*
2114 * Change the port parameters
2115 */
2116static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
2117 struct ktermios *old)
2118{
2119 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2120 unsigned long flags;
2121 unsigned int old_mode, mode, imr, quot, baud, div, cd, fp = 0;
2122
2123 /* save the current mode register */
2124 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
2125
2126 /* reset the mode, clock divisor, parity, stop bits and data size */
2127 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP |
2128 ATMEL_US_PAR | ATMEL_US_USMODE);
2129
2130 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
2131
2132 /* byte size */
2133 switch (termios->c_cflag & CSIZE) {
2134 case CS5:
2135 mode |= ATMEL_US_CHRL_5;
2136 break;
2137 case CS6:
2138 mode |= ATMEL_US_CHRL_6;
2139 break;
2140 case CS7:
2141 mode |= ATMEL_US_CHRL_7;
2142 break;
2143 default:
2144 mode |= ATMEL_US_CHRL_8;
2145 break;
2146 }
2147
2148 /* stop bits */
2149 if (termios->c_cflag & CSTOPB)
2150 mode |= ATMEL_US_NBSTOP_2;
2151
2152 /* parity */
2153 if (termios->c_cflag & PARENB) {
2154 /* Mark or Space parity */
2155 if (termios->c_cflag & CMSPAR) {
2156 if (termios->c_cflag & PARODD)
2157 mode |= ATMEL_US_PAR_MARK;
2158 else
2159 mode |= ATMEL_US_PAR_SPACE;
2160 } else if (termios->c_cflag & PARODD)
2161 mode |= ATMEL_US_PAR_ODD;
2162 else
2163 mode |= ATMEL_US_PAR_EVEN;
2164 } else
2165 mode |= ATMEL_US_PAR_NONE;
2166
2167 spin_lock_irqsave(&port->lock, flags);
2168
2169 port->read_status_mask = ATMEL_US_OVRE;
2170 if (termios->c_iflag & INPCK)
2171 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2172 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
2173 port->read_status_mask |= ATMEL_US_RXBRK;
2174
2175 if (atmel_use_pdc_rx(port))
2176 /* need to enable error interrupts */
2177 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask);
2178
2179 /*
2180 * Characters to ignore
2181 */
2182 port->ignore_status_mask = 0;
2183 if (termios->c_iflag & IGNPAR)
2184 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2185 if (termios->c_iflag & IGNBRK) {
2186 port->ignore_status_mask |= ATMEL_US_RXBRK;
2187 /*
2188 * If we're ignoring parity and break indicators,
2189 * ignore overruns too (for real raw support).
2190 */
2191 if (termios->c_iflag & IGNPAR)
2192 port->ignore_status_mask |= ATMEL_US_OVRE;
2193 }
2194 /* TODO: Ignore all characters if CREAD is set.*/
2195
2196 /* update the per-port timeout */
2197 uart_update_timeout(port, termios->c_cflag, baud);
2198
2199 /*
2200 * save/disable interrupts. The tty layer will ensure that the
2201 * transmitter is empty if requested by the caller, so there's
2202 * no need to wait for it here.
2203 */
2204 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2205 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2206
2207 /* disable receiver and transmitter */
2208 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
2209 atmel_port->tx_stopped = true;
2210
2211 /* mode */
2212 if (port->rs485.flags & SER_RS485_ENABLED) {
2213 atmel_uart_writel(port, ATMEL_US_TTGR,
2214 port->rs485.delay_rts_after_send);
2215 mode |= ATMEL_US_USMODE_RS485;
2216 } else if (port->iso7816.flags & SER_ISO7816_ENABLED) {
2217 atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg);
2218 /* select mck clock, and output */
2219 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
2220 /* set max iterations */
2221 mode |= ATMEL_US_MAX_ITER(3);
2222 if ((port->iso7816.flags & SER_ISO7816_T_PARAM)
2223 == SER_ISO7816_T(0))
2224 mode |= ATMEL_US_USMODE_ISO7816_T0;
2225 else
2226 mode |= ATMEL_US_USMODE_ISO7816_T1;
2227 } else if (termios->c_cflag & CRTSCTS) {
2228 /* RS232 with hardware handshake (RTS/CTS) */
2229 if (atmel_use_fifo(port) &&
2230 !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) {
2231 /*
2232 * with ATMEL_US_USMODE_HWHS set, the controller will
2233 * be able to drive the RTS pin high/low when the RX
2234 * FIFO is above RXFTHRES/below RXFTHRES2.
2235 * It will also disable the transmitter when the CTS
2236 * pin is high.
2237 * This mode is not activated if CTS pin is a GPIO
2238 * because in this case, the transmitter is always
2239 * disabled (there must be an internal pull-up
2240 * responsible for this behaviour).
2241 * If the RTS pin is a GPIO, the controller won't be
2242 * able to drive it according to the FIFO thresholds,
2243 * but it will be handled by the driver.
2244 */
2245 mode |= ATMEL_US_USMODE_HWHS;
2246 } else {
2247 /*
2248 * For platforms without FIFO, the flow control is
2249 * handled by the driver.
2250 */
2251 mode |= ATMEL_US_USMODE_NORMAL;
2252 }
2253 } else {
2254 /* RS232 without hadware handshake */
2255 mode |= ATMEL_US_USMODE_NORMAL;
2256 }
2257
2258 /*
2259 * Set the baud rate:
2260 * Fractional baudrate allows to setup output frequency more
2261 * accurately. This feature is enabled only when using normal mode.
2262 * baudrate = selected clock / (8 * (2 - OVER) * (CD + FP / 8))
2263 * Currently, OVER is always set to 0 so we get
2264 * baudrate = selected clock / (16 * (CD + FP / 8))
2265 * then
2266 * 8 CD + FP = selected clock / (2 * baudrate)
2267 */
2268 if (atmel_port->has_frac_baudrate) {
2269 div = DIV_ROUND_CLOSEST(port->uartclk, baud * 2);
2270 cd = div >> 3;
2271 fp = div & ATMEL_US_FP_MASK;
2272 } else {
2273 cd = uart_get_divisor(port, baud);
2274 }
2275
2276 if (cd > 65535) { /* BRGR is 16-bit, so switch to slower clock */
2277 cd /= 8;
2278 mode |= ATMEL_US_USCLKS_MCK_DIV8;
2279 }
2280 quot = cd | fp << ATMEL_US_FP_OFFSET;
2281
2282 if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
2283 atmel_uart_writel(port, ATMEL_US_BRGR, quot);
2284
2285 /* set the mode, clock divisor, parity, stop bits and data size */
2286 atmel_uart_writel(port, ATMEL_US_MR, mode);
2287
2288 /*
2289 * when switching the mode, set the RTS line state according to the
2290 * new mode, otherwise keep the former state
2291 */
2292 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) {
2293 unsigned int rts_state;
2294
2295 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
2296 /* let the hardware control the RTS line */
2297 rts_state = ATMEL_US_RTSDIS;
2298 } else {
2299 /* force RTS line to low level */
2300 rts_state = ATMEL_US_RTSEN;
2301 }
2302
2303 atmel_uart_writel(port, ATMEL_US_CR, rts_state);
2304 }
2305
2306 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2307 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2308 atmel_port->tx_stopped = false;
2309
2310 /* restore interrupts */
2311 atmel_uart_writel(port, ATMEL_US_IER, imr);
2312
2313 /* CTS flow-control and modem-status interrupts */
2314 if (UART_ENABLE_MS(port, termios->c_cflag))
2315 atmel_enable_ms(port);
2316 else
2317 atmel_disable_ms(port);
2318
2319 spin_unlock_irqrestore(&port->lock, flags);
2320}
2321
2322static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios)
2323{
2324 if (termios->c_line == N_PPS) {
2325 port->flags |= UPF_HARDPPS_CD;
2326 spin_lock_irq(&port->lock);
2327 atmel_enable_ms(port);
2328 spin_unlock_irq(&port->lock);
2329 } else {
2330 port->flags &= ~UPF_HARDPPS_CD;
2331 if (!UART_ENABLE_MS(port, termios->c_cflag)) {
2332 spin_lock_irq(&port->lock);
2333 atmel_disable_ms(port);
2334 spin_unlock_irq(&port->lock);
2335 }
2336 }
2337}
2338
2339/*
2340 * Return string describing the specified port
2341 */
2342static const char *atmel_type(struct uart_port *port)
2343{
2344 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
2345}
2346
2347/*
2348 * Release the memory region(s) being used by 'port'.
2349 */
2350static void atmel_release_port(struct uart_port *port)
2351{
2352 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2353 int size = resource_size(mpdev->resource);
2354
2355 release_mem_region(port->mapbase, size);
2356
2357 if (port->flags & UPF_IOREMAP) {
2358 iounmap(port->membase);
2359 port->membase = NULL;
2360 }
2361}
2362
2363/*
2364 * Request the memory region(s) being used by 'port'.
2365 */
2366static int atmel_request_port(struct uart_port *port)
2367{
2368 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2369 int size = resource_size(mpdev->resource);
2370
2371 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
2372 return -EBUSY;
2373
2374 if (port->flags & UPF_IOREMAP) {
2375 port->membase = ioremap(port->mapbase, size);
2376 if (port->membase == NULL) {
2377 release_mem_region(port->mapbase, size);
2378 return -ENOMEM;
2379 }
2380 }
2381
2382 return 0;
2383}
2384
2385/*
2386 * Configure/autoconfigure the port.
2387 */
2388static void atmel_config_port(struct uart_port *port, int flags)
2389{
2390 if (flags & UART_CONFIG_TYPE) {
2391 port->type = PORT_ATMEL;
2392 atmel_request_port(port);
2393 }
2394}
2395
2396/*
2397 * Verify the new serial_struct (for TIOCSSERIAL).
2398 */
2399static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
2400{
2401 int ret = 0;
2402 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
2403 ret = -EINVAL;
2404 if (port->irq != ser->irq)
2405 ret = -EINVAL;
2406 if (ser->io_type != SERIAL_IO_MEM)
2407 ret = -EINVAL;
2408 if (port->uartclk / 16 != ser->baud_base)
2409 ret = -EINVAL;
2410 if (port->mapbase != (unsigned long)ser->iomem_base)
2411 ret = -EINVAL;
2412 if (port->iobase != ser->port)
2413 ret = -EINVAL;
2414 if (ser->hub6 != 0)
2415 ret = -EINVAL;
2416 return ret;
2417}
2418
2419#ifdef CONFIG_CONSOLE_POLL
2420static int atmel_poll_get_char(struct uart_port *port)
2421{
2422 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
2423 cpu_relax();
2424
2425 return atmel_uart_read_char(port);
2426}
2427
2428static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
2429{
2430 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2431 cpu_relax();
2432
2433 atmel_uart_write_char(port, ch);
2434}
2435#endif
2436
2437static const struct uart_ops atmel_pops = {
2438 .tx_empty = atmel_tx_empty,
2439 .set_mctrl = atmel_set_mctrl,
2440 .get_mctrl = atmel_get_mctrl,
2441 .stop_tx = atmel_stop_tx,
2442 .start_tx = atmel_start_tx,
2443 .stop_rx = atmel_stop_rx,
2444 .enable_ms = atmel_enable_ms,
2445 .break_ctl = atmel_break_ctl,
2446 .startup = atmel_startup,
2447 .shutdown = atmel_shutdown,
2448 .flush_buffer = atmel_flush_buffer,
2449 .set_termios = atmel_set_termios,
2450 .set_ldisc = atmel_set_ldisc,
2451 .type = atmel_type,
2452 .release_port = atmel_release_port,
2453 .request_port = atmel_request_port,
2454 .config_port = atmel_config_port,
2455 .verify_port = atmel_verify_port,
2456 .pm = atmel_serial_pm,
2457#ifdef CONFIG_CONSOLE_POLL
2458 .poll_get_char = atmel_poll_get_char,
2459 .poll_put_char = atmel_poll_put_char,
2460#endif
2461};
2462
2463/*
2464 * Configure the port from the platform device resource info.
2465 */
2466static int atmel_init_port(struct atmel_uart_port *atmel_port,
2467 struct platform_device *pdev)
2468{
2469 int ret;
2470 struct uart_port *port = &atmel_port->uart;
2471 struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
2472
2473 atmel_init_property(atmel_port, pdev);
2474 atmel_set_ops(port);
2475
2476 port->iotype = UPIO_MEM;
2477 port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
2478 port->ops = &atmel_pops;
2479 port->fifosize = 1;
2480 port->dev = &pdev->dev;
2481 port->mapbase = mpdev->resource[0].start;
2482 port->irq = mpdev->resource[1].start;
2483 port->rs485_config = atmel_config_rs485;
2484 port->iso7816_config = atmel_config_iso7816;
2485 port->membase = NULL;
2486
2487 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
2488
2489 ret = uart_get_rs485_mode(port);
2490 if (ret)
2491 return ret;
2492
2493 /* for console, the clock could already be configured */
2494 if (!atmel_port->clk) {
2495 atmel_port->clk = clk_get(&mpdev->dev, "usart");
2496 if (IS_ERR(atmel_port->clk)) {
2497 ret = PTR_ERR(atmel_port->clk);
2498 atmel_port->clk = NULL;
2499 return ret;
2500 }
2501 ret = clk_prepare_enable(atmel_port->clk);
2502 if (ret) {
2503 clk_put(atmel_port->clk);
2504 atmel_port->clk = NULL;
2505 return ret;
2506 }
2507 port->uartclk = clk_get_rate(atmel_port->clk);
2508 clk_disable_unprepare(atmel_port->clk);
2509 /* only enable clock when USART is in use */
2510 }
2511
2512 /*
2513 * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or
2514 * ENDTX|TXBUFE
2515 */
2516 if (atmel_uart_is_half_duplex(port))
2517 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
2518 else if (atmel_use_pdc_tx(port)) {
2519 port->fifosize = PDC_BUFFER_SIZE;
2520 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
2521 } else {
2522 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
2523 }
2524
2525 return 0;
2526}
2527
2528#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2529static void atmel_console_putchar(struct uart_port *port, int ch)
2530{
2531 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2532 cpu_relax();
2533 atmel_uart_write_char(port, ch);
2534}
2535
2536/*
2537 * Interrupts are disabled on entering
2538 */
2539static void atmel_console_write(struct console *co, const char *s, u_int count)
2540{
2541 struct uart_port *port = &atmel_ports[co->index].uart;
2542 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2543 unsigned int status, imr;
2544 unsigned int pdc_tx;
2545
2546 /*
2547 * First, save IMR and then disable interrupts
2548 */
2549 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2550 atmel_uart_writel(port, ATMEL_US_IDR,
2551 ATMEL_US_RXRDY | atmel_port->tx_done_mask);
2552
2553 /* Store PDC transmit status and disable it */
2554 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN;
2555 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
2556
2557 /* Make sure that tx path is actually able to send characters */
2558 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
2559 atmel_port->tx_stopped = false;
2560
2561 uart_console_write(port, s, count, atmel_console_putchar);
2562
2563 /*
2564 * Finally, wait for transmitter to become empty
2565 * and restore IMR
2566 */
2567 do {
2568 status = atmel_uart_readl(port, ATMEL_US_CSR);
2569 } while (!(status & ATMEL_US_TXRDY));
2570
2571 /* Restore PDC transmit status */
2572 if (pdc_tx)
2573 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
2574
2575 /* set interrupts back the way they were */
2576 atmel_uart_writel(port, ATMEL_US_IER, imr);
2577}
2578
2579/*
2580 * If the port was already initialised (eg, by a boot loader),
2581 * try to determine the current setup.
2582 */
2583static void __init atmel_console_get_options(struct uart_port *port, int *baud,
2584 int *parity, int *bits)
2585{
2586 unsigned int mr, quot;
2587
2588 /*
2589 * If the baud rate generator isn't running, the port wasn't
2590 * initialized by the boot loader.
2591 */
2592 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD;
2593 if (!quot)
2594 return;
2595
2596 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL;
2597 if (mr == ATMEL_US_CHRL_8)
2598 *bits = 8;
2599 else
2600 *bits = 7;
2601
2602 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR;
2603 if (mr == ATMEL_US_PAR_EVEN)
2604 *parity = 'e';
2605 else if (mr == ATMEL_US_PAR_ODD)
2606 *parity = 'o';
2607
2608 /*
2609 * The serial core only rounds down when matching this to a
2610 * supported baud rate. Make sure we don't end up slightly
2611 * lower than one of those, as it would make us fall through
2612 * to a much lower baud rate than we really want.
2613 */
2614 *baud = port->uartclk / (16 * (quot - 1));
2615}
2616
2617static int __init atmel_console_setup(struct console *co, char *options)
2618{
2619 int ret;
2620 struct uart_port *port = &atmel_ports[co->index].uart;
2621 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2622 int baud = 115200;
2623 int bits = 8;
2624 int parity = 'n';
2625 int flow = 'n';
2626
2627 if (port->membase == NULL) {
2628 /* Port not initialized yet - delay setup */
2629 return -ENODEV;
2630 }
2631
2632 ret = clk_prepare_enable(atmel_ports[co->index].clk);
2633 if (ret)
2634 return ret;
2635
2636 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2637 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2638 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2639 atmel_port->tx_stopped = false;
2640
2641 if (options)
2642 uart_parse_options(options, &baud, &parity, &bits, &flow);
2643 else
2644 atmel_console_get_options(port, &baud, &parity, &bits);
2645
2646 return uart_set_options(port, co, baud, parity, bits, flow);
2647}
2648
2649static struct uart_driver atmel_uart;
2650
2651static struct console atmel_console = {
2652 .name = ATMEL_DEVICENAME,
2653 .write = atmel_console_write,
2654 .device = uart_console_device,
2655 .setup = atmel_console_setup,
2656 .flags = CON_PRINTBUFFER,
2657 .index = -1,
2658 .data = &atmel_uart,
2659};
2660
2661#define ATMEL_CONSOLE_DEVICE (&atmel_console)
2662
2663#else
2664#define ATMEL_CONSOLE_DEVICE NULL
2665#endif
2666
2667static struct uart_driver atmel_uart = {
2668 .owner = THIS_MODULE,
2669 .driver_name = "atmel_serial",
2670 .dev_name = ATMEL_DEVICENAME,
2671 .major = SERIAL_ATMEL_MAJOR,
2672 .minor = MINOR_START,
2673 .nr = ATMEL_MAX_UART,
2674 .cons = ATMEL_CONSOLE_DEVICE,
2675};
2676
2677#ifdef CONFIG_PM
2678static bool atmel_serial_clk_will_stop(void)
2679{
2680#ifdef CONFIG_ARCH_AT91
2681 return at91_suspend_entering_slow_clock();
2682#else
2683 return false;
2684#endif
2685}
2686
2687static int atmel_serial_suspend(struct platform_device *pdev,
2688 pm_message_t state)
2689{
2690 struct uart_port *port = platform_get_drvdata(pdev);
2691 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2692
2693 if (uart_console(port) && console_suspend_enabled) {
2694 /* Drain the TX shifter */
2695 while (!(atmel_uart_readl(port, ATMEL_US_CSR) &
2696 ATMEL_US_TXEMPTY))
2697 cpu_relax();
2698 }
2699
2700 if (uart_console(port) && !console_suspend_enabled) {
2701 /* Cache register values as we won't get a full shutdown/startup
2702 * cycle
2703 */
2704 atmel_port->cache.mr = atmel_uart_readl(port, ATMEL_US_MR);
2705 atmel_port->cache.imr = atmel_uart_readl(port, ATMEL_US_IMR);
2706 atmel_port->cache.brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
2707 atmel_port->cache.rtor = atmel_uart_readl(port,
2708 atmel_port->rtor);
2709 atmel_port->cache.ttgr = atmel_uart_readl(port, ATMEL_US_TTGR);
2710 atmel_port->cache.fmr = atmel_uart_readl(port, ATMEL_US_FMR);
2711 atmel_port->cache.fimr = atmel_uart_readl(port, ATMEL_US_FIMR);
2712 }
2713
2714 /* we can not wake up if we're running on slow clock */
2715 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
2716 if (atmel_serial_clk_will_stop()) {
2717 unsigned long flags;
2718
2719 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2720 atmel_port->suspended = true;
2721 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2722 device_set_wakeup_enable(&pdev->dev, 0);
2723 }
2724
2725 uart_suspend_port(&atmel_uart, port);
2726
2727 return 0;
2728}
2729
2730static int atmel_serial_resume(struct platform_device *pdev)
2731{
2732 struct uart_port *port = platform_get_drvdata(pdev);
2733 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2734 unsigned long flags;
2735
2736 if (uart_console(port) && !console_suspend_enabled) {
2737 atmel_uart_writel(port, ATMEL_US_MR, atmel_port->cache.mr);
2738 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->cache.imr);
2739 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->cache.brgr);
2740 atmel_uart_writel(port, atmel_port->rtor,
2741 atmel_port->cache.rtor);
2742 atmel_uart_writel(port, ATMEL_US_TTGR, atmel_port->cache.ttgr);
2743
2744 if (atmel_port->fifo_size) {
2745 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_FIFOEN |
2746 ATMEL_US_RXFCLR | ATMEL_US_TXFLCLR);
2747 atmel_uart_writel(port, ATMEL_US_FMR,
2748 atmel_port->cache.fmr);
2749 atmel_uart_writel(port, ATMEL_US_FIER,
2750 atmel_port->cache.fimr);
2751 }
2752 atmel_start_rx(port);
2753 }
2754
2755 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2756 if (atmel_port->pending) {
2757 atmel_handle_receive(port, atmel_port->pending);
2758 atmel_handle_status(port, atmel_port->pending,
2759 atmel_port->pending_status);
2760 atmel_handle_transmit(port, atmel_port->pending);
2761 atmel_port->pending = 0;
2762 }
2763 atmel_port->suspended = false;
2764 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2765
2766 uart_resume_port(&atmel_uart, port);
2767 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
2768
2769 return 0;
2770}
2771#else
2772#define atmel_serial_suspend NULL
2773#define atmel_serial_resume NULL
2774#endif
2775
2776static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
2777 struct platform_device *pdev)
2778{
2779 atmel_port->fifo_size = 0;
2780 atmel_port->rts_low = 0;
2781 atmel_port->rts_high = 0;
2782
2783 if (of_property_read_u32(pdev->dev.of_node,
2784 "atmel,fifo-size",
2785 &atmel_port->fifo_size))
2786 return;
2787
2788 if (!atmel_port->fifo_size)
2789 return;
2790
2791 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) {
2792 atmel_port->fifo_size = 0;
2793 dev_err(&pdev->dev, "Invalid FIFO size\n");
2794 return;
2795 }
2796
2797 /*
2798 * 0 <= rts_low <= rts_high <= fifo_size
2799 * Once their CTS line asserted by the remote peer, some x86 UARTs tend
2800 * to flush their internal TX FIFO, commonly up to 16 data, before
2801 * actually stopping to send new data. So we try to set the RTS High
2802 * Threshold to a reasonably high value respecting this 16 data
2803 * empirical rule when possible.
2804 */
2805 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1,
2806 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET);
2807 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2,
2808 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET);
2809
2810 dev_info(&pdev->dev, "Using FIFO (%u data)\n",
2811 atmel_port->fifo_size);
2812 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n",
2813 atmel_port->rts_high);
2814 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n",
2815 atmel_port->rts_low);
2816}
2817
2818static int atmel_serial_probe(struct platform_device *pdev)
2819{
2820 struct atmel_uart_port *atmel_port;
2821 struct device_node *np = pdev->dev.parent->of_node;
2822 void *data;
2823 int ret;
2824 bool rs485_enabled;
2825
2826 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
2827
2828 /*
2829 * In device tree there is no node with "atmel,at91rm9200-usart-serial"
2830 * as compatible string. This driver is probed by at91-usart mfd driver
2831 * which is just a wrapper over the atmel_serial driver and
2832 * spi-at91-usart driver. All attributes needed by this driver are
2833 * found in of_node of parent.
2834 */
2835 pdev->dev.of_node = np;
2836
2837 ret = of_alias_get_id(np, "serial");
2838 if (ret < 0)
2839 /* port id not found in platform data nor device-tree aliases:
2840 * auto-enumerate it */
2841 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART);
2842
2843 if (ret >= ATMEL_MAX_UART) {
2844 ret = -ENODEV;
2845 goto err;
2846 }
2847
2848 if (test_and_set_bit(ret, atmel_ports_in_use)) {
2849 /* port already in use */
2850 ret = -EBUSY;
2851 goto err;
2852 }
2853
2854 atmel_port = &atmel_ports[ret];
2855 atmel_port->backup_imr = 0;
2856 atmel_port->uart.line = ret;
2857 atmel_port->uart.has_sysrq = IS_ENABLED(CONFIG_SERIAL_ATMEL_CONSOLE);
2858 atmel_serial_probe_fifos(atmel_port, pdev);
2859
2860 atomic_set(&atmel_port->tasklet_shutdown, 0);
2861 spin_lock_init(&atmel_port->lock_suspended);
2862
2863 ret = atmel_init_port(atmel_port, pdev);
2864 if (ret)
2865 goto err_clear_bit;
2866
2867 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0);
2868 if (IS_ERR(atmel_port->gpios)) {
2869 ret = PTR_ERR(atmel_port->gpios);
2870 goto err_clear_bit;
2871 }
2872
2873 if (!atmel_use_pdc_rx(&atmel_port->uart)) {
2874 ret = -ENOMEM;
2875 data = kmalloc_array(ATMEL_SERIAL_RINGSIZE,
2876 sizeof(struct atmel_uart_char),
2877 GFP_KERNEL);
2878 if (!data)
2879 goto err_alloc_ring;
2880 atmel_port->rx_ring.buf = data;
2881 }
2882
2883 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED;
2884
2885 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart);
2886 if (ret)
2887 goto err_add_port;
2888
2889#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2890 if (uart_console(&atmel_port->uart)
2891 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
2892 /*
2893 * The serial core enabled the clock for us, so undo
2894 * the clk_prepare_enable() in atmel_console_setup()
2895 */
2896 clk_disable_unprepare(atmel_port->clk);
2897 }
2898#endif
2899
2900 device_init_wakeup(&pdev->dev, 1);
2901 platform_set_drvdata(pdev, atmel_port);
2902
2903 /*
2904 * The peripheral clock has been disabled by atmel_init_port():
2905 * enable it before accessing I/O registers
2906 */
2907 clk_prepare_enable(atmel_port->clk);
2908
2909 if (rs485_enabled) {
2910 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR,
2911 ATMEL_US_USMODE_NORMAL);
2912 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR,
2913 ATMEL_US_RTSEN);
2914 }
2915
2916 /*
2917 * Get port name of usart or uart
2918 */
2919 atmel_get_ip_name(&atmel_port->uart);
2920
2921 /*
2922 * The peripheral clock can now safely be disabled till the port
2923 * is used
2924 */
2925 clk_disable_unprepare(atmel_port->clk);
2926
2927 return 0;
2928
2929err_add_port:
2930 kfree(atmel_port->rx_ring.buf);
2931 atmel_port->rx_ring.buf = NULL;
2932err_alloc_ring:
2933 if (!uart_console(&atmel_port->uart)) {
2934 clk_put(atmel_port->clk);
2935 atmel_port->clk = NULL;
2936 }
2937err_clear_bit:
2938 clear_bit(atmel_port->uart.line, atmel_ports_in_use);
2939err:
2940 return ret;
2941}
2942
2943/*
2944 * Even if the driver is not modular, it makes sense to be able to
2945 * unbind a device: there can be many bound devices, and there are
2946 * situations where dynamic binding and unbinding can be useful.
2947 *
2948 * For example, a connected device can require a specific firmware update
2949 * protocol that needs bitbanging on IO lines, but use the regular serial
2950 * port in the normal case.
2951 */
2952static int atmel_serial_remove(struct platform_device *pdev)
2953{
2954 struct uart_port *port = platform_get_drvdata(pdev);
2955 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2956 int ret = 0;
2957
2958 tasklet_kill(&atmel_port->tasklet_rx);
2959 tasklet_kill(&atmel_port->tasklet_tx);
2960
2961 device_init_wakeup(&pdev->dev, 0);
2962
2963 ret = uart_remove_one_port(&atmel_uart, port);
2964
2965 kfree(atmel_port->rx_ring.buf);
2966
2967 /* "port" is allocated statically, so we shouldn't free it */
2968
2969 clear_bit(port->line, atmel_ports_in_use);
2970
2971 clk_put(atmel_port->clk);
2972 atmel_port->clk = NULL;
2973 pdev->dev.of_node = NULL;
2974
2975 return ret;
2976}
2977
2978static struct platform_driver atmel_serial_driver = {
2979 .probe = atmel_serial_probe,
2980 .remove = atmel_serial_remove,
2981 .suspend = atmel_serial_suspend,
2982 .resume = atmel_serial_resume,
2983 .driver = {
2984 .name = "atmel_usart_serial",
2985 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
2986 },
2987};
2988
2989static int __init atmel_serial_init(void)
2990{
2991 int ret;
2992
2993 ret = uart_register_driver(&atmel_uart);
2994 if (ret)
2995 return ret;
2996
2997 ret = platform_driver_register(&atmel_serial_driver);
2998 if (ret)
2999 uart_unregister_driver(&atmel_uart);
3000
3001 return ret;
3002}
3003device_initcall(atmel_serial_init);
1/*
2 * Driver for Atmel AT91 / AT32 Serial ports
3 * Copyright (C) 2003 Rick Bronson
4 *
5 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
6 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
7 *
8 * DMA support added by Chip Coldwell.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; either version 2 of the License, or
13 * (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 *
24 */
25#include <linux/module.h>
26#include <linux/tty.h>
27#include <linux/ioport.h>
28#include <linux/slab.h>
29#include <linux/init.h>
30#include <linux/serial.h>
31#include <linux/clk.h>
32#include <linux/console.h>
33#include <linux/sysrq.h>
34#include <linux/tty_flip.h>
35#include <linux/platform_device.h>
36#include <linux/of.h>
37#include <linux/of_device.h>
38#include <linux/dma-mapping.h>
39#include <linux/atmel_pdc.h>
40#include <linux/atmel_serial.h>
41#include <linux/uaccess.h>
42
43#include <asm/io.h>
44#include <asm/ioctls.h>
45
46#include <asm/mach/serial_at91.h>
47#include <mach/board.h>
48
49#ifdef CONFIG_ARM
50#include <mach/cpu.h>
51#include <asm/gpio.h>
52#endif
53
54#define PDC_BUFFER_SIZE 512
55/* Revisit: We should calculate this based on the actual port settings */
56#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
57
58#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
59#define SUPPORT_SYSRQ
60#endif
61
62#include <linux/serial_core.h>
63
64static void atmel_start_rx(struct uart_port *port);
65static void atmel_stop_rx(struct uart_port *port);
66
67#ifdef CONFIG_SERIAL_ATMEL_TTYAT
68
69/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
70 * should coexist with the 8250 driver, such as if we have an external 16C550
71 * UART. */
72#define SERIAL_ATMEL_MAJOR 204
73#define MINOR_START 154
74#define ATMEL_DEVICENAME "ttyAT"
75
76#else
77
78/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
79 * name, but it is legally reserved for the 8250 driver. */
80#define SERIAL_ATMEL_MAJOR TTY_MAJOR
81#define MINOR_START 64
82#define ATMEL_DEVICENAME "ttyS"
83
84#endif
85
86#define ATMEL_ISR_PASS_LIMIT 256
87
88/* UART registers. CR is write-only, hence no GET macro */
89#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
90#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
91#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
92#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
93#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
94#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
95#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
96#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
97#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
98#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
99#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
100#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
101#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
102
103 /* PDC registers */
104#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
105#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
106
107#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
108#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
109#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
110#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
111#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
112
113#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
114#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
115#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
116
117static int (*atmel_open_hook)(struct uart_port *);
118static void (*atmel_close_hook)(struct uart_port *);
119
120struct atmel_dma_buffer {
121 unsigned char *buf;
122 dma_addr_t dma_addr;
123 unsigned int dma_size;
124 unsigned int ofs;
125};
126
127struct atmel_uart_char {
128 u16 status;
129 u16 ch;
130};
131
132#define ATMEL_SERIAL_RINGSIZE 1024
133
134/*
135 * We wrap our port structure around the generic uart_port.
136 */
137struct atmel_uart_port {
138 struct uart_port uart; /* uart */
139 struct clk *clk; /* uart clock */
140 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
141 u32 backup_imr; /* IMR saved during suspend */
142 int break_active; /* break being received */
143
144 short use_dma_rx; /* enable PDC receiver */
145 short pdc_rx_idx; /* current PDC RX buffer */
146 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
147
148 short use_dma_tx; /* enable PDC transmitter */
149 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
150
151 struct tasklet_struct tasklet;
152 unsigned int irq_status;
153 unsigned int irq_status_prev;
154
155 struct circ_buf rx_ring;
156
157 struct serial_rs485 rs485; /* rs485 settings */
158 unsigned int tx_done_mask;
159};
160
161static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
162static unsigned long atmel_ports_in_use;
163
164#ifdef SUPPORT_SYSRQ
165static struct console atmel_console;
166#endif
167
168#if defined(CONFIG_OF)
169static const struct of_device_id atmel_serial_dt_ids[] = {
170 { .compatible = "atmel,at91rm9200-usart" },
171 { .compatible = "atmel,at91sam9260-usart" },
172 { /* sentinel */ }
173};
174
175MODULE_DEVICE_TABLE(of, atmel_serial_dt_ids);
176#endif
177
178static inline struct atmel_uart_port *
179to_atmel_uart_port(struct uart_port *uart)
180{
181 return container_of(uart, struct atmel_uart_port, uart);
182}
183
184#ifdef CONFIG_SERIAL_ATMEL_PDC
185static bool atmel_use_dma_rx(struct uart_port *port)
186{
187 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
188
189 return atmel_port->use_dma_rx;
190}
191
192static bool atmel_use_dma_tx(struct uart_port *port)
193{
194 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
195
196 return atmel_port->use_dma_tx;
197}
198#else
199static bool atmel_use_dma_rx(struct uart_port *port)
200{
201 return false;
202}
203
204static bool atmel_use_dma_tx(struct uart_port *port)
205{
206 return false;
207}
208#endif
209
210/* Enable or disable the rs485 support */
211void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf)
212{
213 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
214 unsigned int mode;
215 unsigned long flags;
216
217 spin_lock_irqsave(&port->lock, flags);
218
219 /* Disable interrupts */
220 UART_PUT_IDR(port, atmel_port->tx_done_mask);
221
222 mode = UART_GET_MR(port);
223
224 /* Resetting serial mode to RS232 (0x0) */
225 mode &= ~ATMEL_US_USMODE;
226
227 atmel_port->rs485 = *rs485conf;
228
229 if (rs485conf->flags & SER_RS485_ENABLED) {
230 dev_dbg(port->dev, "Setting UART to RS485\n");
231 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
232 if ((rs485conf->delay_rts_after_send) > 0)
233 UART_PUT_TTGR(port, rs485conf->delay_rts_after_send);
234 mode |= ATMEL_US_USMODE_RS485;
235 } else {
236 dev_dbg(port->dev, "Setting UART to RS232\n");
237 if (atmel_use_dma_tx(port))
238 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
239 ATMEL_US_TXBUFE;
240 else
241 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
242 }
243 UART_PUT_MR(port, mode);
244
245 /* Enable interrupts */
246 UART_PUT_IER(port, atmel_port->tx_done_mask);
247
248 spin_unlock_irqrestore(&port->lock, flags);
249
250}
251
252/*
253 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
254 */
255static u_int atmel_tx_empty(struct uart_port *port)
256{
257 return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0;
258}
259
260/*
261 * Set state of the modem control output lines
262 */
263static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
264{
265 unsigned int control = 0;
266 unsigned int mode;
267 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
268
269#ifdef CONFIG_ARCH_AT91RM9200
270 if (cpu_is_at91rm9200()) {
271 /*
272 * AT91RM9200 Errata #39: RTS0 is not internally connected
273 * to PA21. We need to drive the pin manually.
274 */
275 if (port->mapbase == AT91RM9200_BASE_US0) {
276 if (mctrl & TIOCM_RTS)
277 at91_set_gpio_value(AT91_PIN_PA21, 0);
278 else
279 at91_set_gpio_value(AT91_PIN_PA21, 1);
280 }
281 }
282#endif
283
284 if (mctrl & TIOCM_RTS)
285 control |= ATMEL_US_RTSEN;
286 else
287 control |= ATMEL_US_RTSDIS;
288
289 if (mctrl & TIOCM_DTR)
290 control |= ATMEL_US_DTREN;
291 else
292 control |= ATMEL_US_DTRDIS;
293
294 UART_PUT_CR(port, control);
295
296 /* Local loopback mode? */
297 mode = UART_GET_MR(port) & ~ATMEL_US_CHMODE;
298 if (mctrl & TIOCM_LOOP)
299 mode |= ATMEL_US_CHMODE_LOC_LOOP;
300 else
301 mode |= ATMEL_US_CHMODE_NORMAL;
302
303 /* Resetting serial mode to RS232 (0x0) */
304 mode &= ~ATMEL_US_USMODE;
305
306 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
307 dev_dbg(port->dev, "Setting UART to RS485\n");
308 if ((atmel_port->rs485.delay_rts_after_send) > 0)
309 UART_PUT_TTGR(port,
310 atmel_port->rs485.delay_rts_after_send);
311 mode |= ATMEL_US_USMODE_RS485;
312 } else {
313 dev_dbg(port->dev, "Setting UART to RS232\n");
314 }
315 UART_PUT_MR(port, mode);
316}
317
318/*
319 * Get state of the modem control input lines
320 */
321static u_int atmel_get_mctrl(struct uart_port *port)
322{
323 unsigned int status, ret = 0;
324
325 status = UART_GET_CSR(port);
326
327 /*
328 * The control signals are active low.
329 */
330 if (!(status & ATMEL_US_DCD))
331 ret |= TIOCM_CD;
332 if (!(status & ATMEL_US_CTS))
333 ret |= TIOCM_CTS;
334 if (!(status & ATMEL_US_DSR))
335 ret |= TIOCM_DSR;
336 if (!(status & ATMEL_US_RI))
337 ret |= TIOCM_RI;
338
339 return ret;
340}
341
342/*
343 * Stop transmitting.
344 */
345static void atmel_stop_tx(struct uart_port *port)
346{
347 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
348
349 if (atmel_use_dma_tx(port)) {
350 /* disable PDC transmit */
351 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
352 }
353 /* Disable interrupts */
354 UART_PUT_IDR(port, atmel_port->tx_done_mask);
355
356 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
357 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX))
358 atmel_start_rx(port);
359}
360
361/*
362 * Start transmitting.
363 */
364static void atmel_start_tx(struct uart_port *port)
365{
366 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
367
368 if (atmel_use_dma_tx(port)) {
369 if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN)
370 /* The transmitter is already running. Yes, we
371 really need this.*/
372 return;
373
374 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
375 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX))
376 atmel_stop_rx(port);
377
378 /* re-enable PDC transmit */
379 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
380 }
381 /* Enable interrupts */
382 UART_PUT_IER(port, atmel_port->tx_done_mask);
383}
384
385/*
386 * start receiving - port is in process of being opened.
387 */
388static void atmel_start_rx(struct uart_port *port)
389{
390 UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */
391
392 UART_PUT_CR(port, ATMEL_US_RXEN);
393
394 if (atmel_use_dma_rx(port)) {
395 /* enable PDC controller */
396 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
397 port->read_status_mask);
398 UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
399 } else {
400 UART_PUT_IER(port, ATMEL_US_RXRDY);
401 }
402}
403
404/*
405 * Stop receiving - port is in process of being closed.
406 */
407static void atmel_stop_rx(struct uart_port *port)
408{
409 UART_PUT_CR(port, ATMEL_US_RXDIS);
410
411 if (atmel_use_dma_rx(port)) {
412 /* disable PDC receive */
413 UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS);
414 UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
415 port->read_status_mask);
416 } else {
417 UART_PUT_IDR(port, ATMEL_US_RXRDY);
418 }
419}
420
421/*
422 * Enable modem status interrupts
423 */
424static void atmel_enable_ms(struct uart_port *port)
425{
426 UART_PUT_IER(port, ATMEL_US_RIIC | ATMEL_US_DSRIC
427 | ATMEL_US_DCDIC | ATMEL_US_CTSIC);
428}
429
430/*
431 * Control the transmission of a break signal
432 */
433static void atmel_break_ctl(struct uart_port *port, int break_state)
434{
435 if (break_state != 0)
436 UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */
437 else
438 UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */
439}
440
441/*
442 * Stores the incoming character in the ring buffer
443 */
444static void
445atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
446 unsigned int ch)
447{
448 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
449 struct circ_buf *ring = &atmel_port->rx_ring;
450 struct atmel_uart_char *c;
451
452 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
453 /* Buffer overflow, ignore char */
454 return;
455
456 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
457 c->status = status;
458 c->ch = ch;
459
460 /* Make sure the character is stored before we update head. */
461 smp_wmb();
462
463 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
464}
465
466/*
467 * Deal with parity, framing and overrun errors.
468 */
469static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
470{
471 /* clear error */
472 UART_PUT_CR(port, ATMEL_US_RSTSTA);
473
474 if (status & ATMEL_US_RXBRK) {
475 /* ignore side-effect */
476 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
477 port->icount.brk++;
478 }
479 if (status & ATMEL_US_PARE)
480 port->icount.parity++;
481 if (status & ATMEL_US_FRAME)
482 port->icount.frame++;
483 if (status & ATMEL_US_OVRE)
484 port->icount.overrun++;
485}
486
487/*
488 * Characters received (called from interrupt handler)
489 */
490static void atmel_rx_chars(struct uart_port *port)
491{
492 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
493 unsigned int status, ch;
494
495 status = UART_GET_CSR(port);
496 while (status & ATMEL_US_RXRDY) {
497 ch = UART_GET_CHAR(port);
498
499 /*
500 * note that the error handling code is
501 * out of the main execution path
502 */
503 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
504 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
505 || atmel_port->break_active)) {
506
507 /* clear error */
508 UART_PUT_CR(port, ATMEL_US_RSTSTA);
509
510 if (status & ATMEL_US_RXBRK
511 && !atmel_port->break_active) {
512 atmel_port->break_active = 1;
513 UART_PUT_IER(port, ATMEL_US_RXBRK);
514 } else {
515 /*
516 * This is either the end-of-break
517 * condition or we've received at
518 * least one character without RXBRK
519 * being set. In both cases, the next
520 * RXBRK will indicate start-of-break.
521 */
522 UART_PUT_IDR(port, ATMEL_US_RXBRK);
523 status &= ~ATMEL_US_RXBRK;
524 atmel_port->break_active = 0;
525 }
526 }
527
528 atmel_buffer_rx_char(port, status, ch);
529 status = UART_GET_CSR(port);
530 }
531
532 tasklet_schedule(&atmel_port->tasklet);
533}
534
535/*
536 * Transmit characters (called from tasklet with TXRDY interrupt
537 * disabled)
538 */
539static void atmel_tx_chars(struct uart_port *port)
540{
541 struct circ_buf *xmit = &port->state->xmit;
542 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
543
544 if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) {
545 UART_PUT_CHAR(port, port->x_char);
546 port->icount.tx++;
547 port->x_char = 0;
548 }
549 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
550 return;
551
552 while (UART_GET_CSR(port) & atmel_port->tx_done_mask) {
553 UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
554 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
555 port->icount.tx++;
556 if (uart_circ_empty(xmit))
557 break;
558 }
559
560 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
561 uart_write_wakeup(port);
562
563 if (!uart_circ_empty(xmit))
564 /* Enable interrupts */
565 UART_PUT_IER(port, atmel_port->tx_done_mask);
566}
567
568/*
569 * receive interrupt handler.
570 */
571static void
572atmel_handle_receive(struct uart_port *port, unsigned int pending)
573{
574 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
575
576 if (atmel_use_dma_rx(port)) {
577 /*
578 * PDC receive. Just schedule the tasklet and let it
579 * figure out the details.
580 *
581 * TODO: We're not handling error flags correctly at
582 * the moment.
583 */
584 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
585 UART_PUT_IDR(port, (ATMEL_US_ENDRX
586 | ATMEL_US_TIMEOUT));
587 tasklet_schedule(&atmel_port->tasklet);
588 }
589
590 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
591 ATMEL_US_FRAME | ATMEL_US_PARE))
592 atmel_pdc_rxerr(port, pending);
593 }
594
595 /* Interrupt receive */
596 if (pending & ATMEL_US_RXRDY)
597 atmel_rx_chars(port);
598 else if (pending & ATMEL_US_RXBRK) {
599 /*
600 * End of break detected. If it came along with a
601 * character, atmel_rx_chars will handle it.
602 */
603 UART_PUT_CR(port, ATMEL_US_RSTSTA);
604 UART_PUT_IDR(port, ATMEL_US_RXBRK);
605 atmel_port->break_active = 0;
606 }
607}
608
609/*
610 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
611 */
612static void
613atmel_handle_transmit(struct uart_port *port, unsigned int pending)
614{
615 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
616
617 if (pending & atmel_port->tx_done_mask) {
618 /* Either PDC or interrupt transmission */
619 UART_PUT_IDR(port, atmel_port->tx_done_mask);
620 tasklet_schedule(&atmel_port->tasklet);
621 }
622}
623
624/*
625 * status flags interrupt handler.
626 */
627static void
628atmel_handle_status(struct uart_port *port, unsigned int pending,
629 unsigned int status)
630{
631 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
632
633 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
634 | ATMEL_US_CTSIC)) {
635 atmel_port->irq_status = status;
636 tasklet_schedule(&atmel_port->tasklet);
637 }
638}
639
640/*
641 * Interrupt handler
642 */
643static irqreturn_t atmel_interrupt(int irq, void *dev_id)
644{
645 struct uart_port *port = dev_id;
646 unsigned int status, pending, pass_counter = 0;
647
648 do {
649 status = UART_GET_CSR(port);
650 pending = status & UART_GET_IMR(port);
651 if (!pending)
652 break;
653
654 atmel_handle_receive(port, pending);
655 atmel_handle_status(port, pending, status);
656 atmel_handle_transmit(port, pending);
657 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
658
659 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
660}
661
662/*
663 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
664 */
665static void atmel_tx_dma(struct uart_port *port)
666{
667 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
668 struct circ_buf *xmit = &port->state->xmit;
669 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
670 int count;
671
672 /* nothing left to transmit? */
673 if (UART_GET_TCR(port))
674 return;
675
676 xmit->tail += pdc->ofs;
677 xmit->tail &= UART_XMIT_SIZE - 1;
678
679 port->icount.tx += pdc->ofs;
680 pdc->ofs = 0;
681
682 /* more to transmit - setup next transfer */
683
684 /* disable PDC transmit */
685 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
686
687 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
688 dma_sync_single_for_device(port->dev,
689 pdc->dma_addr,
690 pdc->dma_size,
691 DMA_TO_DEVICE);
692
693 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
694 pdc->ofs = count;
695
696 UART_PUT_TPR(port, pdc->dma_addr + xmit->tail);
697 UART_PUT_TCR(port, count);
698 /* re-enable PDC transmit */
699 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
700 /* Enable interrupts */
701 UART_PUT_IER(port, atmel_port->tx_done_mask);
702 } else {
703 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
704 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) {
705 /* DMA done, stop TX, start RX for RS485 */
706 atmel_start_rx(port);
707 }
708 }
709
710 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
711 uart_write_wakeup(port);
712}
713
714static void atmel_rx_from_ring(struct uart_port *port)
715{
716 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
717 struct circ_buf *ring = &atmel_port->rx_ring;
718 unsigned int flg;
719 unsigned int status;
720
721 while (ring->head != ring->tail) {
722 struct atmel_uart_char c;
723
724 /* Make sure c is loaded after head. */
725 smp_rmb();
726
727 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
728
729 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
730
731 port->icount.rx++;
732 status = c.status;
733 flg = TTY_NORMAL;
734
735 /*
736 * note that the error handling code is
737 * out of the main execution path
738 */
739 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
740 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
741 if (status & ATMEL_US_RXBRK) {
742 /* ignore side-effect */
743 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
744
745 port->icount.brk++;
746 if (uart_handle_break(port))
747 continue;
748 }
749 if (status & ATMEL_US_PARE)
750 port->icount.parity++;
751 if (status & ATMEL_US_FRAME)
752 port->icount.frame++;
753 if (status & ATMEL_US_OVRE)
754 port->icount.overrun++;
755
756 status &= port->read_status_mask;
757
758 if (status & ATMEL_US_RXBRK)
759 flg = TTY_BREAK;
760 else if (status & ATMEL_US_PARE)
761 flg = TTY_PARITY;
762 else if (status & ATMEL_US_FRAME)
763 flg = TTY_FRAME;
764 }
765
766
767 if (uart_handle_sysrq_char(port, c.ch))
768 continue;
769
770 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
771 }
772
773 /*
774 * Drop the lock here since it might end up calling
775 * uart_start(), which takes the lock.
776 */
777 spin_unlock(&port->lock);
778 tty_flip_buffer_push(port->state->port.tty);
779 spin_lock(&port->lock);
780}
781
782static void atmel_rx_from_dma(struct uart_port *port)
783{
784 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
785 struct tty_struct *tty = port->state->port.tty;
786 struct atmel_dma_buffer *pdc;
787 int rx_idx = atmel_port->pdc_rx_idx;
788 unsigned int head;
789 unsigned int tail;
790 unsigned int count;
791
792 do {
793 /* Reset the UART timeout early so that we don't miss one */
794 UART_PUT_CR(port, ATMEL_US_STTTO);
795
796 pdc = &atmel_port->pdc_rx[rx_idx];
797 head = UART_GET_RPR(port) - pdc->dma_addr;
798 tail = pdc->ofs;
799
800 /* If the PDC has switched buffers, RPR won't contain
801 * any address within the current buffer. Since head
802 * is unsigned, we just need a one-way comparison to
803 * find out.
804 *
805 * In this case, we just need to consume the entire
806 * buffer and resubmit it for DMA. This will clear the
807 * ENDRX bit as well, so that we can safely re-enable
808 * all interrupts below.
809 */
810 head = min(head, pdc->dma_size);
811
812 if (likely(head != tail)) {
813 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
814 pdc->dma_size, DMA_FROM_DEVICE);
815
816 /*
817 * head will only wrap around when we recycle
818 * the DMA buffer, and when that happens, we
819 * explicitly set tail to 0. So head will
820 * always be greater than tail.
821 */
822 count = head - tail;
823
824 tty_insert_flip_string(tty, pdc->buf + pdc->ofs, count);
825
826 dma_sync_single_for_device(port->dev, pdc->dma_addr,
827 pdc->dma_size, DMA_FROM_DEVICE);
828
829 port->icount.rx += count;
830 pdc->ofs = head;
831 }
832
833 /*
834 * If the current buffer is full, we need to check if
835 * the next one contains any additional data.
836 */
837 if (head >= pdc->dma_size) {
838 pdc->ofs = 0;
839 UART_PUT_RNPR(port, pdc->dma_addr);
840 UART_PUT_RNCR(port, pdc->dma_size);
841
842 rx_idx = !rx_idx;
843 atmel_port->pdc_rx_idx = rx_idx;
844 }
845 } while (head >= pdc->dma_size);
846
847 /*
848 * Drop the lock here since it might end up calling
849 * uart_start(), which takes the lock.
850 */
851 spin_unlock(&port->lock);
852 tty_flip_buffer_push(tty);
853 spin_lock(&port->lock);
854
855 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
856}
857
858/*
859 * tasklet handling tty stuff outside the interrupt handler.
860 */
861static void atmel_tasklet_func(unsigned long data)
862{
863 struct uart_port *port = (struct uart_port *)data;
864 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
865 unsigned int status;
866 unsigned int status_change;
867
868 /* The interrupt handler does not take the lock */
869 spin_lock(&port->lock);
870
871 if (atmel_use_dma_tx(port))
872 atmel_tx_dma(port);
873 else
874 atmel_tx_chars(port);
875
876 status = atmel_port->irq_status;
877 status_change = status ^ atmel_port->irq_status_prev;
878
879 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
880 | ATMEL_US_DCD | ATMEL_US_CTS)) {
881 /* TODO: All reads to CSR will clear these interrupts! */
882 if (status_change & ATMEL_US_RI)
883 port->icount.rng++;
884 if (status_change & ATMEL_US_DSR)
885 port->icount.dsr++;
886 if (status_change & ATMEL_US_DCD)
887 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
888 if (status_change & ATMEL_US_CTS)
889 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
890
891 wake_up_interruptible(&port->state->port.delta_msr_wait);
892
893 atmel_port->irq_status_prev = status;
894 }
895
896 if (atmel_use_dma_rx(port))
897 atmel_rx_from_dma(port);
898 else
899 atmel_rx_from_ring(port);
900
901 spin_unlock(&port->lock);
902}
903
904/*
905 * Perform initialization and enable port for reception
906 */
907static int atmel_startup(struct uart_port *port)
908{
909 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
910 struct tty_struct *tty = port->state->port.tty;
911 int retval;
912
913 /*
914 * Ensure that no interrupts are enabled otherwise when
915 * request_irq() is called we could get stuck trying to
916 * handle an unexpected interrupt
917 */
918 UART_PUT_IDR(port, -1);
919
920 /*
921 * Allocate the IRQ
922 */
923 retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED,
924 tty ? tty->name : "atmel_serial", port);
925 if (retval) {
926 printk("atmel_serial: atmel_startup - Can't get irq\n");
927 return retval;
928 }
929
930 /*
931 * Initialize DMA (if necessary)
932 */
933 if (atmel_use_dma_rx(port)) {
934 int i;
935
936 for (i = 0; i < 2; i++) {
937 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
938
939 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
940 if (pdc->buf == NULL) {
941 if (i != 0) {
942 dma_unmap_single(port->dev,
943 atmel_port->pdc_rx[0].dma_addr,
944 PDC_BUFFER_SIZE,
945 DMA_FROM_DEVICE);
946 kfree(atmel_port->pdc_rx[0].buf);
947 }
948 free_irq(port->irq, port);
949 return -ENOMEM;
950 }
951 pdc->dma_addr = dma_map_single(port->dev,
952 pdc->buf,
953 PDC_BUFFER_SIZE,
954 DMA_FROM_DEVICE);
955 pdc->dma_size = PDC_BUFFER_SIZE;
956 pdc->ofs = 0;
957 }
958
959 atmel_port->pdc_rx_idx = 0;
960
961 UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr);
962 UART_PUT_RCR(port, PDC_BUFFER_SIZE);
963
964 UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr);
965 UART_PUT_RNCR(port, PDC_BUFFER_SIZE);
966 }
967 if (atmel_use_dma_tx(port)) {
968 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
969 struct circ_buf *xmit = &port->state->xmit;
970
971 pdc->buf = xmit->buf;
972 pdc->dma_addr = dma_map_single(port->dev,
973 pdc->buf,
974 UART_XMIT_SIZE,
975 DMA_TO_DEVICE);
976 pdc->dma_size = UART_XMIT_SIZE;
977 pdc->ofs = 0;
978 }
979
980 /*
981 * If there is a specific "open" function (to register
982 * control line interrupts)
983 */
984 if (atmel_open_hook) {
985 retval = atmel_open_hook(port);
986 if (retval) {
987 free_irq(port->irq, port);
988 return retval;
989 }
990 }
991
992 /* Save current CSR for comparison in atmel_tasklet_func() */
993 atmel_port->irq_status_prev = UART_GET_CSR(port);
994 atmel_port->irq_status = atmel_port->irq_status_prev;
995
996 /*
997 * Finally, enable the serial port
998 */
999 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1000 /* enable xmit & rcvr */
1001 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1002
1003 if (atmel_use_dma_rx(port)) {
1004 /* set UART timeout */
1005 UART_PUT_RTOR(port, PDC_RX_TIMEOUT);
1006 UART_PUT_CR(port, ATMEL_US_STTTO);
1007
1008 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1009 /* enable PDC controller */
1010 UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
1011 } else {
1012 /* enable receive only */
1013 UART_PUT_IER(port, ATMEL_US_RXRDY);
1014 }
1015
1016 return 0;
1017}
1018
1019/*
1020 * Disable the port
1021 */
1022static void atmel_shutdown(struct uart_port *port)
1023{
1024 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1025 /*
1026 * Ensure everything is stopped.
1027 */
1028 atmel_stop_rx(port);
1029 atmel_stop_tx(port);
1030
1031 /*
1032 * Shut-down the DMA.
1033 */
1034 if (atmel_use_dma_rx(port)) {
1035 int i;
1036
1037 for (i = 0; i < 2; i++) {
1038 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1039
1040 dma_unmap_single(port->dev,
1041 pdc->dma_addr,
1042 pdc->dma_size,
1043 DMA_FROM_DEVICE);
1044 kfree(pdc->buf);
1045 }
1046 }
1047 if (atmel_use_dma_tx(port)) {
1048 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1049
1050 dma_unmap_single(port->dev,
1051 pdc->dma_addr,
1052 pdc->dma_size,
1053 DMA_TO_DEVICE);
1054 }
1055
1056 /*
1057 * Disable all interrupts, port and break condition.
1058 */
1059 UART_PUT_CR(port, ATMEL_US_RSTSTA);
1060 UART_PUT_IDR(port, -1);
1061
1062 /*
1063 * Free the interrupt
1064 */
1065 free_irq(port->irq, port);
1066
1067 /*
1068 * If there is a specific "close" function (to unregister
1069 * control line interrupts)
1070 */
1071 if (atmel_close_hook)
1072 atmel_close_hook(port);
1073}
1074
1075/*
1076 * Flush any TX data submitted for DMA. Called when the TX circular
1077 * buffer is reset.
1078 */
1079static void atmel_flush_buffer(struct uart_port *port)
1080{
1081 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1082
1083 if (atmel_use_dma_tx(port)) {
1084 UART_PUT_TCR(port, 0);
1085 atmel_port->pdc_tx.ofs = 0;
1086 }
1087}
1088
1089/*
1090 * Power / Clock management.
1091 */
1092static void atmel_serial_pm(struct uart_port *port, unsigned int state,
1093 unsigned int oldstate)
1094{
1095 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1096
1097 switch (state) {
1098 case 0:
1099 /*
1100 * Enable the peripheral clock for this serial port.
1101 * This is called on uart_open() or a resume event.
1102 */
1103 clk_enable(atmel_port->clk);
1104
1105 /* re-enable interrupts if we disabled some on suspend */
1106 UART_PUT_IER(port, atmel_port->backup_imr);
1107 break;
1108 case 3:
1109 /* Back up the interrupt mask and disable all interrupts */
1110 atmel_port->backup_imr = UART_GET_IMR(port);
1111 UART_PUT_IDR(port, -1);
1112
1113 /*
1114 * Disable the peripheral clock for this serial port.
1115 * This is called on uart_close() or a suspend event.
1116 */
1117 clk_disable(atmel_port->clk);
1118 break;
1119 default:
1120 printk(KERN_ERR "atmel_serial: unknown pm %d\n", state);
1121 }
1122}
1123
1124/*
1125 * Change the port parameters
1126 */
1127static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
1128 struct ktermios *old)
1129{
1130 unsigned long flags;
1131 unsigned int mode, imr, quot, baud;
1132 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1133
1134 /* Get current mode register */
1135 mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL
1136 | ATMEL_US_NBSTOP | ATMEL_US_PAR
1137 | ATMEL_US_USMODE);
1138
1139 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
1140 quot = uart_get_divisor(port, baud);
1141
1142 if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
1143 quot /= 8;
1144 mode |= ATMEL_US_USCLKS_MCK_DIV8;
1145 }
1146
1147 /* byte size */
1148 switch (termios->c_cflag & CSIZE) {
1149 case CS5:
1150 mode |= ATMEL_US_CHRL_5;
1151 break;
1152 case CS6:
1153 mode |= ATMEL_US_CHRL_6;
1154 break;
1155 case CS7:
1156 mode |= ATMEL_US_CHRL_7;
1157 break;
1158 default:
1159 mode |= ATMEL_US_CHRL_8;
1160 break;
1161 }
1162
1163 /* stop bits */
1164 if (termios->c_cflag & CSTOPB)
1165 mode |= ATMEL_US_NBSTOP_2;
1166
1167 /* parity */
1168 if (termios->c_cflag & PARENB) {
1169 /* Mark or Space parity */
1170 if (termios->c_cflag & CMSPAR) {
1171 if (termios->c_cflag & PARODD)
1172 mode |= ATMEL_US_PAR_MARK;
1173 else
1174 mode |= ATMEL_US_PAR_SPACE;
1175 } else if (termios->c_cflag & PARODD)
1176 mode |= ATMEL_US_PAR_ODD;
1177 else
1178 mode |= ATMEL_US_PAR_EVEN;
1179 } else
1180 mode |= ATMEL_US_PAR_NONE;
1181
1182 /* hardware handshake (RTS/CTS) */
1183 if (termios->c_cflag & CRTSCTS)
1184 mode |= ATMEL_US_USMODE_HWHS;
1185 else
1186 mode |= ATMEL_US_USMODE_NORMAL;
1187
1188 spin_lock_irqsave(&port->lock, flags);
1189
1190 port->read_status_mask = ATMEL_US_OVRE;
1191 if (termios->c_iflag & INPCK)
1192 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
1193 if (termios->c_iflag & (BRKINT | PARMRK))
1194 port->read_status_mask |= ATMEL_US_RXBRK;
1195
1196 if (atmel_use_dma_rx(port))
1197 /* need to enable error interrupts */
1198 UART_PUT_IER(port, port->read_status_mask);
1199
1200 /*
1201 * Characters to ignore
1202 */
1203 port->ignore_status_mask = 0;
1204 if (termios->c_iflag & IGNPAR)
1205 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
1206 if (termios->c_iflag & IGNBRK) {
1207 port->ignore_status_mask |= ATMEL_US_RXBRK;
1208 /*
1209 * If we're ignoring parity and break indicators,
1210 * ignore overruns too (for real raw support).
1211 */
1212 if (termios->c_iflag & IGNPAR)
1213 port->ignore_status_mask |= ATMEL_US_OVRE;
1214 }
1215 /* TODO: Ignore all characters if CREAD is set.*/
1216
1217 /* update the per-port timeout */
1218 uart_update_timeout(port, termios->c_cflag, baud);
1219
1220 /*
1221 * save/disable interrupts. The tty layer will ensure that the
1222 * transmitter is empty if requested by the caller, so there's
1223 * no need to wait for it here.
1224 */
1225 imr = UART_GET_IMR(port);
1226 UART_PUT_IDR(port, -1);
1227
1228 /* disable receiver and transmitter */
1229 UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
1230
1231 /* Resetting serial mode to RS232 (0x0) */
1232 mode &= ~ATMEL_US_USMODE;
1233
1234 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
1235 dev_dbg(port->dev, "Setting UART to RS485\n");
1236 if ((atmel_port->rs485.delay_rts_after_send) > 0)
1237 UART_PUT_TTGR(port,
1238 atmel_port->rs485.delay_rts_after_send);
1239 mode |= ATMEL_US_USMODE_RS485;
1240 } else {
1241 dev_dbg(port->dev, "Setting UART to RS232\n");
1242 }
1243
1244 /* set the parity, stop bits and data size */
1245 UART_PUT_MR(port, mode);
1246
1247 /* set the baud rate */
1248 UART_PUT_BRGR(port, quot);
1249 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1250 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1251
1252 /* restore interrupts */
1253 UART_PUT_IER(port, imr);
1254
1255 /* CTS flow-control and modem-status interrupts */
1256 if (UART_ENABLE_MS(port, termios->c_cflag))
1257 port->ops->enable_ms(port);
1258
1259 spin_unlock_irqrestore(&port->lock, flags);
1260}
1261
1262static void atmel_set_ldisc(struct uart_port *port, int new)
1263{
1264 if (new == N_PPS) {
1265 port->flags |= UPF_HARDPPS_CD;
1266 atmel_enable_ms(port);
1267 } else {
1268 port->flags &= ~UPF_HARDPPS_CD;
1269 }
1270}
1271
1272/*
1273 * Return string describing the specified port
1274 */
1275static const char *atmel_type(struct uart_port *port)
1276{
1277 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
1278}
1279
1280/*
1281 * Release the memory region(s) being used by 'port'.
1282 */
1283static void atmel_release_port(struct uart_port *port)
1284{
1285 struct platform_device *pdev = to_platform_device(port->dev);
1286 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
1287
1288 release_mem_region(port->mapbase, size);
1289
1290 if (port->flags & UPF_IOREMAP) {
1291 iounmap(port->membase);
1292 port->membase = NULL;
1293 }
1294}
1295
1296/*
1297 * Request the memory region(s) being used by 'port'.
1298 */
1299static int atmel_request_port(struct uart_port *port)
1300{
1301 struct platform_device *pdev = to_platform_device(port->dev);
1302 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
1303
1304 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
1305 return -EBUSY;
1306
1307 if (port->flags & UPF_IOREMAP) {
1308 port->membase = ioremap(port->mapbase, size);
1309 if (port->membase == NULL) {
1310 release_mem_region(port->mapbase, size);
1311 return -ENOMEM;
1312 }
1313 }
1314
1315 return 0;
1316}
1317
1318/*
1319 * Configure/autoconfigure the port.
1320 */
1321static void atmel_config_port(struct uart_port *port, int flags)
1322{
1323 if (flags & UART_CONFIG_TYPE) {
1324 port->type = PORT_ATMEL;
1325 atmel_request_port(port);
1326 }
1327}
1328
1329/*
1330 * Verify the new serial_struct (for TIOCSSERIAL).
1331 */
1332static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
1333{
1334 int ret = 0;
1335 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
1336 ret = -EINVAL;
1337 if (port->irq != ser->irq)
1338 ret = -EINVAL;
1339 if (ser->io_type != SERIAL_IO_MEM)
1340 ret = -EINVAL;
1341 if (port->uartclk / 16 != ser->baud_base)
1342 ret = -EINVAL;
1343 if ((void *)port->mapbase != ser->iomem_base)
1344 ret = -EINVAL;
1345 if (port->iobase != ser->port)
1346 ret = -EINVAL;
1347 if (ser->hub6 != 0)
1348 ret = -EINVAL;
1349 return ret;
1350}
1351
1352#ifdef CONFIG_CONSOLE_POLL
1353static int atmel_poll_get_char(struct uart_port *port)
1354{
1355 while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY))
1356 cpu_relax();
1357
1358 return UART_GET_CHAR(port);
1359}
1360
1361static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
1362{
1363 while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
1364 cpu_relax();
1365
1366 UART_PUT_CHAR(port, ch);
1367}
1368#endif
1369
1370static int
1371atmel_ioctl(struct uart_port *port, unsigned int cmd, unsigned long arg)
1372{
1373 struct serial_rs485 rs485conf;
1374
1375 switch (cmd) {
1376 case TIOCSRS485:
1377 if (copy_from_user(&rs485conf, (struct serial_rs485 *) arg,
1378 sizeof(rs485conf)))
1379 return -EFAULT;
1380
1381 atmel_config_rs485(port, &rs485conf);
1382 break;
1383
1384 case TIOCGRS485:
1385 if (copy_to_user((struct serial_rs485 *) arg,
1386 &(to_atmel_uart_port(port)->rs485),
1387 sizeof(rs485conf)))
1388 return -EFAULT;
1389 break;
1390
1391 default:
1392 return -ENOIOCTLCMD;
1393 }
1394 return 0;
1395}
1396
1397
1398
1399static struct uart_ops atmel_pops = {
1400 .tx_empty = atmel_tx_empty,
1401 .set_mctrl = atmel_set_mctrl,
1402 .get_mctrl = atmel_get_mctrl,
1403 .stop_tx = atmel_stop_tx,
1404 .start_tx = atmel_start_tx,
1405 .stop_rx = atmel_stop_rx,
1406 .enable_ms = atmel_enable_ms,
1407 .break_ctl = atmel_break_ctl,
1408 .startup = atmel_startup,
1409 .shutdown = atmel_shutdown,
1410 .flush_buffer = atmel_flush_buffer,
1411 .set_termios = atmel_set_termios,
1412 .set_ldisc = atmel_set_ldisc,
1413 .type = atmel_type,
1414 .release_port = atmel_release_port,
1415 .request_port = atmel_request_port,
1416 .config_port = atmel_config_port,
1417 .verify_port = atmel_verify_port,
1418 .pm = atmel_serial_pm,
1419 .ioctl = atmel_ioctl,
1420#ifdef CONFIG_CONSOLE_POLL
1421 .poll_get_char = atmel_poll_get_char,
1422 .poll_put_char = atmel_poll_put_char,
1423#endif
1424};
1425
1426static void __devinit atmel_of_init_port(struct atmel_uart_port *atmel_port,
1427 struct device_node *np)
1428{
1429 u32 rs485_delay[2];
1430
1431 /* DMA/PDC usage specification */
1432 if (of_get_property(np, "atmel,use-dma-rx", NULL))
1433 atmel_port->use_dma_rx = 1;
1434 else
1435 atmel_port->use_dma_rx = 0;
1436 if (of_get_property(np, "atmel,use-dma-tx", NULL))
1437 atmel_port->use_dma_tx = 1;
1438 else
1439 atmel_port->use_dma_tx = 0;
1440
1441 /* rs485 properties */
1442 if (of_property_read_u32_array(np, "rs485-rts-delay",
1443 rs485_delay, 2) == 0) {
1444 struct serial_rs485 *rs485conf = &atmel_port->rs485;
1445
1446 rs485conf->delay_rts_before_send = rs485_delay[0];
1447 rs485conf->delay_rts_after_send = rs485_delay[1];
1448 rs485conf->flags = 0;
1449
1450 if (of_get_property(np, "rs485-rx-during-tx", NULL))
1451 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1452
1453 if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
1454 rs485conf->flags |= SER_RS485_ENABLED;
1455 }
1456}
1457
1458/*
1459 * Configure the port from the platform device resource info.
1460 */
1461static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
1462 struct platform_device *pdev)
1463{
1464 struct uart_port *port = &atmel_port->uart;
1465 struct atmel_uart_data *pdata = pdev->dev.platform_data;
1466
1467 if (pdev->dev.of_node) {
1468 atmel_of_init_port(atmel_port, pdev->dev.of_node);
1469 } else {
1470 atmel_port->use_dma_rx = pdata->use_dma_rx;
1471 atmel_port->use_dma_tx = pdata->use_dma_tx;
1472 atmel_port->rs485 = pdata->rs485;
1473 }
1474
1475 port->iotype = UPIO_MEM;
1476 port->flags = UPF_BOOT_AUTOCONF;
1477 port->ops = &atmel_pops;
1478 port->fifosize = 1;
1479 port->dev = &pdev->dev;
1480 port->mapbase = pdev->resource[0].start;
1481 port->irq = pdev->resource[1].start;
1482
1483 tasklet_init(&atmel_port->tasklet, atmel_tasklet_func,
1484 (unsigned long)port);
1485
1486 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
1487
1488 if (pdata && pdata->regs) {
1489 /* Already mapped by setup code */
1490 port->membase = pdata->regs;
1491 } else {
1492 port->flags |= UPF_IOREMAP;
1493 port->membase = NULL;
1494 }
1495
1496 /* for console, the clock could already be configured */
1497 if (!atmel_port->clk) {
1498 atmel_port->clk = clk_get(&pdev->dev, "usart");
1499 clk_enable(atmel_port->clk);
1500 port->uartclk = clk_get_rate(atmel_port->clk);
1501 clk_disable(atmel_port->clk);
1502 /* only enable clock when USART is in use */
1503 }
1504
1505 /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
1506 if (atmel_port->rs485.flags & SER_RS485_ENABLED)
1507 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
1508 else if (atmel_use_dma_tx(port)) {
1509 port->fifosize = PDC_BUFFER_SIZE;
1510 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
1511 } else {
1512 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
1513 }
1514}
1515
1516/*
1517 * Register board-specific modem-control line handlers.
1518 */
1519void __init atmel_register_uart_fns(struct atmel_port_fns *fns)
1520{
1521 if (fns->enable_ms)
1522 atmel_pops.enable_ms = fns->enable_ms;
1523 if (fns->get_mctrl)
1524 atmel_pops.get_mctrl = fns->get_mctrl;
1525 if (fns->set_mctrl)
1526 atmel_pops.set_mctrl = fns->set_mctrl;
1527 atmel_open_hook = fns->open;
1528 atmel_close_hook = fns->close;
1529 atmel_pops.pm = fns->pm;
1530 atmel_pops.set_wake = fns->set_wake;
1531}
1532
1533struct platform_device *atmel_default_console_device; /* the serial console device */
1534
1535#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
1536static void atmel_console_putchar(struct uart_port *port, int ch)
1537{
1538 while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
1539 cpu_relax();
1540 UART_PUT_CHAR(port, ch);
1541}
1542
1543/*
1544 * Interrupts are disabled on entering
1545 */
1546static void atmel_console_write(struct console *co, const char *s, u_int count)
1547{
1548 struct uart_port *port = &atmel_ports[co->index].uart;
1549 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1550 unsigned int status, imr;
1551 unsigned int pdc_tx;
1552
1553 /*
1554 * First, save IMR and then disable interrupts
1555 */
1556 imr = UART_GET_IMR(port);
1557 UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask);
1558
1559 /* Store PDC transmit status and disable it */
1560 pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN;
1561 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
1562
1563 uart_console_write(port, s, count, atmel_console_putchar);
1564
1565 /*
1566 * Finally, wait for transmitter to become empty
1567 * and restore IMR
1568 */
1569 do {
1570 status = UART_GET_CSR(port);
1571 } while (!(status & ATMEL_US_TXRDY));
1572
1573 /* Restore PDC transmit status */
1574 if (pdc_tx)
1575 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
1576
1577 /* set interrupts back the way they were */
1578 UART_PUT_IER(port, imr);
1579}
1580
1581/*
1582 * If the port was already initialised (eg, by a boot loader),
1583 * try to determine the current setup.
1584 */
1585static void __init atmel_console_get_options(struct uart_port *port, int *baud,
1586 int *parity, int *bits)
1587{
1588 unsigned int mr, quot;
1589
1590 /*
1591 * If the baud rate generator isn't running, the port wasn't
1592 * initialized by the boot loader.
1593 */
1594 quot = UART_GET_BRGR(port) & ATMEL_US_CD;
1595 if (!quot)
1596 return;
1597
1598 mr = UART_GET_MR(port) & ATMEL_US_CHRL;
1599 if (mr == ATMEL_US_CHRL_8)
1600 *bits = 8;
1601 else
1602 *bits = 7;
1603
1604 mr = UART_GET_MR(port) & ATMEL_US_PAR;
1605 if (mr == ATMEL_US_PAR_EVEN)
1606 *parity = 'e';
1607 else if (mr == ATMEL_US_PAR_ODD)
1608 *parity = 'o';
1609
1610 /*
1611 * The serial core only rounds down when matching this to a
1612 * supported baud rate. Make sure we don't end up slightly
1613 * lower than one of those, as it would make us fall through
1614 * to a much lower baud rate than we really want.
1615 */
1616 *baud = port->uartclk / (16 * (quot - 1));
1617}
1618
1619static int __init atmel_console_setup(struct console *co, char *options)
1620{
1621 struct uart_port *port = &atmel_ports[co->index].uart;
1622 int baud = 115200;
1623 int bits = 8;
1624 int parity = 'n';
1625 int flow = 'n';
1626
1627 if (port->membase == NULL) {
1628 /* Port not initialized yet - delay setup */
1629 return -ENODEV;
1630 }
1631
1632 clk_enable(atmel_ports[co->index].clk);
1633
1634 UART_PUT_IDR(port, -1);
1635 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1636 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1637
1638 if (options)
1639 uart_parse_options(options, &baud, &parity, &bits, &flow);
1640 else
1641 atmel_console_get_options(port, &baud, &parity, &bits);
1642
1643 return uart_set_options(port, co, baud, parity, bits, flow);
1644}
1645
1646static struct uart_driver atmel_uart;
1647
1648static struct console atmel_console = {
1649 .name = ATMEL_DEVICENAME,
1650 .write = atmel_console_write,
1651 .device = uart_console_device,
1652 .setup = atmel_console_setup,
1653 .flags = CON_PRINTBUFFER,
1654 .index = -1,
1655 .data = &atmel_uart,
1656};
1657
1658#define ATMEL_CONSOLE_DEVICE (&atmel_console)
1659
1660/*
1661 * Early console initialization (before VM subsystem initialized).
1662 */
1663static int __init atmel_console_init(void)
1664{
1665 if (atmel_default_console_device) {
1666 struct atmel_uart_data *pdata =
1667 atmel_default_console_device->dev.platform_data;
1668 int id = pdata->num;
1669 struct atmel_uart_port *port = &atmel_ports[id];
1670
1671 port->backup_imr = 0;
1672 port->uart.line = id;
1673
1674 add_preferred_console(ATMEL_DEVICENAME, id, NULL);
1675 atmel_init_port(port, atmel_default_console_device);
1676 register_console(&atmel_console);
1677 }
1678
1679 return 0;
1680}
1681
1682console_initcall(atmel_console_init);
1683
1684/*
1685 * Late console initialization.
1686 */
1687static int __init atmel_late_console_init(void)
1688{
1689 if (atmel_default_console_device
1690 && !(atmel_console.flags & CON_ENABLED))
1691 register_console(&atmel_console);
1692
1693 return 0;
1694}
1695
1696core_initcall(atmel_late_console_init);
1697
1698static inline bool atmel_is_console_port(struct uart_port *port)
1699{
1700 return port->cons && port->cons->index == port->line;
1701}
1702
1703#else
1704#define ATMEL_CONSOLE_DEVICE NULL
1705
1706static inline bool atmel_is_console_port(struct uart_port *port)
1707{
1708 return false;
1709}
1710#endif
1711
1712static struct uart_driver atmel_uart = {
1713 .owner = THIS_MODULE,
1714 .driver_name = "atmel_serial",
1715 .dev_name = ATMEL_DEVICENAME,
1716 .major = SERIAL_ATMEL_MAJOR,
1717 .minor = MINOR_START,
1718 .nr = ATMEL_MAX_UART,
1719 .cons = ATMEL_CONSOLE_DEVICE,
1720};
1721
1722#ifdef CONFIG_PM
1723static bool atmel_serial_clk_will_stop(void)
1724{
1725#ifdef CONFIG_ARCH_AT91
1726 return at91_suspend_entering_slow_clock();
1727#else
1728 return false;
1729#endif
1730}
1731
1732static int atmel_serial_suspend(struct platform_device *pdev,
1733 pm_message_t state)
1734{
1735 struct uart_port *port = platform_get_drvdata(pdev);
1736 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1737
1738 if (atmel_is_console_port(port) && console_suspend_enabled) {
1739 /* Drain the TX shifter */
1740 while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY))
1741 cpu_relax();
1742 }
1743
1744 /* we can not wake up if we're running on slow clock */
1745 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
1746 if (atmel_serial_clk_will_stop())
1747 device_set_wakeup_enable(&pdev->dev, 0);
1748
1749 uart_suspend_port(&atmel_uart, port);
1750
1751 return 0;
1752}
1753
1754static int atmel_serial_resume(struct platform_device *pdev)
1755{
1756 struct uart_port *port = platform_get_drvdata(pdev);
1757 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1758
1759 uart_resume_port(&atmel_uart, port);
1760 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
1761
1762 return 0;
1763}
1764#else
1765#define atmel_serial_suspend NULL
1766#define atmel_serial_resume NULL
1767#endif
1768
1769static int __devinit atmel_serial_probe(struct platform_device *pdev)
1770{
1771 struct atmel_uart_port *port;
1772 struct device_node *np = pdev->dev.of_node;
1773 struct atmel_uart_data *pdata = pdev->dev.platform_data;
1774 void *data;
1775 int ret = -ENODEV;
1776
1777 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
1778
1779 if (np)
1780 ret = of_alias_get_id(np, "serial");
1781 else
1782 if (pdata)
1783 ret = pdata->num;
1784
1785 if (ret < 0)
1786 /* port id not found in platform data nor device-tree aliases:
1787 * auto-enumerate it */
1788 ret = find_first_zero_bit(&atmel_ports_in_use,
1789 sizeof(atmel_ports_in_use));
1790
1791 if (ret > ATMEL_MAX_UART) {
1792 ret = -ENODEV;
1793 goto err;
1794 }
1795
1796 if (test_and_set_bit(ret, &atmel_ports_in_use)) {
1797 /* port already in use */
1798 ret = -EBUSY;
1799 goto err;
1800 }
1801
1802 port = &atmel_ports[ret];
1803 port->backup_imr = 0;
1804 port->uart.line = ret;
1805
1806 atmel_init_port(port, pdev);
1807
1808 if (!atmel_use_dma_rx(&port->uart)) {
1809 ret = -ENOMEM;
1810 data = kmalloc(sizeof(struct atmel_uart_char)
1811 * ATMEL_SERIAL_RINGSIZE, GFP_KERNEL);
1812 if (!data)
1813 goto err_alloc_ring;
1814 port->rx_ring.buf = data;
1815 }
1816
1817 ret = uart_add_one_port(&atmel_uart, &port->uart);
1818 if (ret)
1819 goto err_add_port;
1820
1821#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
1822 if (atmel_is_console_port(&port->uart)
1823 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
1824 /*
1825 * The serial core enabled the clock for us, so undo
1826 * the clk_enable() in atmel_console_setup()
1827 */
1828 clk_disable(port->clk);
1829 }
1830#endif
1831
1832 device_init_wakeup(&pdev->dev, 1);
1833 platform_set_drvdata(pdev, port);
1834
1835 if (port->rs485.flags & SER_RS485_ENABLED) {
1836 UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL);
1837 UART_PUT_CR(&port->uart, ATMEL_US_RTSEN);
1838 }
1839
1840 return 0;
1841
1842err_add_port:
1843 kfree(port->rx_ring.buf);
1844 port->rx_ring.buf = NULL;
1845err_alloc_ring:
1846 if (!atmel_is_console_port(&port->uart)) {
1847 clk_put(port->clk);
1848 port->clk = NULL;
1849 }
1850err:
1851 return ret;
1852}
1853
1854static int __devexit atmel_serial_remove(struct platform_device *pdev)
1855{
1856 struct uart_port *port = platform_get_drvdata(pdev);
1857 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1858 int ret = 0;
1859
1860 device_init_wakeup(&pdev->dev, 0);
1861 platform_set_drvdata(pdev, NULL);
1862
1863 ret = uart_remove_one_port(&atmel_uart, port);
1864
1865 tasklet_kill(&atmel_port->tasklet);
1866 kfree(atmel_port->rx_ring.buf);
1867
1868 /* "port" is allocated statically, so we shouldn't free it */
1869
1870 clear_bit(port->line, &atmel_ports_in_use);
1871
1872 clk_put(atmel_port->clk);
1873
1874 return ret;
1875}
1876
1877static struct platform_driver atmel_serial_driver = {
1878 .probe = atmel_serial_probe,
1879 .remove = __devexit_p(atmel_serial_remove),
1880 .suspend = atmel_serial_suspend,
1881 .resume = atmel_serial_resume,
1882 .driver = {
1883 .name = "atmel_usart",
1884 .owner = THIS_MODULE,
1885 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
1886 },
1887};
1888
1889static int __init atmel_serial_init(void)
1890{
1891 int ret;
1892
1893 ret = uart_register_driver(&atmel_uart);
1894 if (ret)
1895 return ret;
1896
1897 ret = platform_driver_register(&atmel_serial_driver);
1898 if (ret)
1899 uart_unregister_driver(&atmel_uart);
1900
1901 return ret;
1902}
1903
1904static void __exit atmel_serial_exit(void)
1905{
1906 platform_driver_unregister(&atmel_serial_driver);
1907 uart_unregister_driver(&atmel_uart);
1908}
1909
1910module_init(atmel_serial_init);
1911module_exit(atmel_serial_exit);
1912
1913MODULE_AUTHOR("Rick Bronson");
1914MODULE_DESCRIPTION("Atmel AT91 / AT32 serial port driver");
1915MODULE_LICENSE("GPL");
1916MODULE_ALIAS("platform:atmel_usart");