Loading...
1/*
2 * xHCI host controller driver
3 *
4 * Copyright (C) 2008 Intel Corp.
5 *
6 * Author: Sarah Sharp
7 * Some code borrowed from the Linux EHCI driver.
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
12 *
13 * This program is distributed in the hope that it will be useful, but
14 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
15 * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
16 * for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software Foundation,
20 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21 */
22
23#include <linux/pci.h>
24#include <linux/irq.h>
25#include <linux/log2.h>
26#include <linux/module.h>
27#include <linux/moduleparam.h>
28#include <linux/slab.h>
29#include <linux/dmi.h>
30#include <linux/dma-mapping.h>
31
32#include "xhci.h"
33#include "xhci-trace.h"
34#include "xhci-mtk.h"
35
36#define DRIVER_AUTHOR "Sarah Sharp"
37#define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
38
39#define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
40
41/* Some 0.95 hardware can't handle the chain bit on a Link TRB being cleared */
42static int link_quirk;
43module_param(link_quirk, int, S_IRUGO | S_IWUSR);
44MODULE_PARM_DESC(link_quirk, "Don't clear the chain bit on a link TRB");
45
46static unsigned int quirks;
47module_param(quirks, uint, S_IRUGO);
48MODULE_PARM_DESC(quirks, "Bit flags for quirks to be enabled as default");
49
50/* TODO: copied from ehci-hcd.c - can this be refactored? */
51/*
52 * xhci_handshake - spin reading hc until handshake completes or fails
53 * @ptr: address of hc register to be read
54 * @mask: bits to look at in result of read
55 * @done: value of those bits when handshake succeeds
56 * @usec: timeout in microseconds
57 *
58 * Returns negative errno, or zero on success
59 *
60 * Success happens when the "mask" bits have the specified value (hardware
61 * handshake done). There are two failure modes: "usec" have passed (major
62 * hardware flakeout), or the register reads as all-ones (hardware removed).
63 */
64int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, int usec)
65{
66 u32 result;
67
68 do {
69 result = readl(ptr);
70 if (result == ~(u32)0) /* card removed */
71 return -ENODEV;
72 result &= mask;
73 if (result == done)
74 return 0;
75 udelay(1);
76 usec--;
77 } while (usec > 0);
78 return -ETIMEDOUT;
79}
80
81/*
82 * Disable interrupts and begin the xHCI halting process.
83 */
84void xhci_quiesce(struct xhci_hcd *xhci)
85{
86 u32 halted;
87 u32 cmd;
88 u32 mask;
89
90 mask = ~(XHCI_IRQS);
91 halted = readl(&xhci->op_regs->status) & STS_HALT;
92 if (!halted)
93 mask &= ~CMD_RUN;
94
95 cmd = readl(&xhci->op_regs->command);
96 cmd &= mask;
97 writel(cmd, &xhci->op_regs->command);
98}
99
100/*
101 * Force HC into halt state.
102 *
103 * Disable any IRQs and clear the run/stop bit.
104 * HC will complete any current and actively pipelined transactions, and
105 * should halt within 16 ms of the run/stop bit being cleared.
106 * Read HC Halted bit in the status register to see when the HC is finished.
107 */
108int xhci_halt(struct xhci_hcd *xhci)
109{
110 int ret;
111 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Halt the HC");
112 xhci_quiesce(xhci);
113
114 ret = xhci_handshake(&xhci->op_regs->status,
115 STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC);
116 if (!ret) {
117 xhci->xhc_state |= XHCI_STATE_HALTED;
118 xhci->cmd_ring_state = CMD_RING_STATE_STOPPED;
119 } else
120 xhci_warn(xhci, "Host not halted after %u microseconds.\n",
121 XHCI_MAX_HALT_USEC);
122 return ret;
123}
124
125/*
126 * Set the run bit and wait for the host to be running.
127 */
128static int xhci_start(struct xhci_hcd *xhci)
129{
130 u32 temp;
131 int ret;
132
133 temp = readl(&xhci->op_regs->command);
134 temp |= (CMD_RUN);
135 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Turn on HC, cmd = 0x%x.",
136 temp);
137 writel(temp, &xhci->op_regs->command);
138
139 /*
140 * Wait for the HCHalted Status bit to be 0 to indicate the host is
141 * running.
142 */
143 ret = xhci_handshake(&xhci->op_regs->status,
144 STS_HALT, 0, XHCI_MAX_HALT_USEC);
145 if (ret == -ETIMEDOUT)
146 xhci_err(xhci, "Host took too long to start, "
147 "waited %u microseconds.\n",
148 XHCI_MAX_HALT_USEC);
149 if (!ret)
150 /* clear state flags. Including dying, halted or removing */
151 xhci->xhc_state = 0;
152
153 return ret;
154}
155
156/*
157 * Reset a halted HC.
158 *
159 * This resets pipelines, timers, counters, state machines, etc.
160 * Transactions will be terminated immediately, and operational registers
161 * will be set to their defaults.
162 */
163int xhci_reset(struct xhci_hcd *xhci)
164{
165 u32 command;
166 u32 state;
167 int ret, i;
168
169 state = readl(&xhci->op_regs->status);
170 if ((state & STS_HALT) == 0) {
171 xhci_warn(xhci, "Host controller not halted, aborting reset.\n");
172 return 0;
173 }
174
175 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Reset the HC");
176 command = readl(&xhci->op_regs->command);
177 command |= CMD_RESET;
178 writel(command, &xhci->op_regs->command);
179
180 /* Existing Intel xHCI controllers require a delay of 1 mS,
181 * after setting the CMD_RESET bit, and before accessing any
182 * HC registers. This allows the HC to complete the
183 * reset operation and be ready for HC register access.
184 * Without this delay, the subsequent HC register access,
185 * may result in a system hang very rarely.
186 */
187 if (xhci->quirks & XHCI_INTEL_HOST)
188 udelay(1000);
189
190 ret = xhci_handshake(&xhci->op_regs->command,
191 CMD_RESET, 0, 10 * 1000 * 1000);
192 if (ret)
193 return ret;
194
195 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
196 "Wait for controller to be ready for doorbell rings");
197 /*
198 * xHCI cannot write to any doorbells or operational registers other
199 * than status until the "Controller Not Ready" flag is cleared.
200 */
201 ret = xhci_handshake(&xhci->op_regs->status,
202 STS_CNR, 0, 10 * 1000 * 1000);
203
204 for (i = 0; i < 2; ++i) {
205 xhci->bus_state[i].port_c_suspend = 0;
206 xhci->bus_state[i].suspended_ports = 0;
207 xhci->bus_state[i].resuming_ports = 0;
208 }
209
210 return ret;
211}
212
213#ifdef CONFIG_PCI
214static int xhci_free_msi(struct xhci_hcd *xhci)
215{
216 int i;
217
218 if (!xhci->msix_entries)
219 return -EINVAL;
220
221 for (i = 0; i < xhci->msix_count; i++)
222 if (xhci->msix_entries[i].vector)
223 free_irq(xhci->msix_entries[i].vector,
224 xhci_to_hcd(xhci));
225 return 0;
226}
227
228/*
229 * Set up MSI
230 */
231static int xhci_setup_msi(struct xhci_hcd *xhci)
232{
233 int ret;
234 struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
235
236 ret = pci_enable_msi(pdev);
237 if (ret) {
238 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
239 "failed to allocate MSI entry");
240 return ret;
241 }
242
243 ret = request_irq(pdev->irq, xhci_msi_irq,
244 0, "xhci_hcd", xhci_to_hcd(xhci));
245 if (ret) {
246 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
247 "disable MSI interrupt");
248 pci_disable_msi(pdev);
249 }
250
251 return ret;
252}
253
254/*
255 * Free IRQs
256 * free all IRQs request
257 */
258static void xhci_free_irq(struct xhci_hcd *xhci)
259{
260 struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
261 int ret;
262
263 /* return if using legacy interrupt */
264 if (xhci_to_hcd(xhci)->irq > 0)
265 return;
266
267 ret = xhci_free_msi(xhci);
268 if (!ret)
269 return;
270 if (pdev->irq > 0)
271 free_irq(pdev->irq, xhci_to_hcd(xhci));
272
273 return;
274}
275
276/*
277 * Set up MSI-X
278 */
279static int xhci_setup_msix(struct xhci_hcd *xhci)
280{
281 int i, ret = 0;
282 struct usb_hcd *hcd = xhci_to_hcd(xhci);
283 struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
284
285 /*
286 * calculate number of msi-x vectors supported.
287 * - HCS_MAX_INTRS: the max number of interrupts the host can handle,
288 * with max number of interrupters based on the xhci HCSPARAMS1.
289 * - num_online_cpus: maximum msi-x vectors per CPUs core.
290 * Add additional 1 vector to ensure always available interrupt.
291 */
292 xhci->msix_count = min(num_online_cpus() + 1,
293 HCS_MAX_INTRS(xhci->hcs_params1));
294
295 xhci->msix_entries =
296 kmalloc((sizeof(struct msix_entry))*xhci->msix_count,
297 GFP_KERNEL);
298 if (!xhci->msix_entries) {
299 xhci_err(xhci, "Failed to allocate MSI-X entries\n");
300 return -ENOMEM;
301 }
302
303 for (i = 0; i < xhci->msix_count; i++) {
304 xhci->msix_entries[i].entry = i;
305 xhci->msix_entries[i].vector = 0;
306 }
307
308 ret = pci_enable_msix_exact(pdev, xhci->msix_entries, xhci->msix_count);
309 if (ret) {
310 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
311 "Failed to enable MSI-X");
312 goto free_entries;
313 }
314
315 for (i = 0; i < xhci->msix_count; i++) {
316 ret = request_irq(xhci->msix_entries[i].vector,
317 xhci_msi_irq,
318 0, "xhci_hcd", xhci_to_hcd(xhci));
319 if (ret)
320 goto disable_msix;
321 }
322
323 hcd->msix_enabled = 1;
324 return ret;
325
326disable_msix:
327 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "disable MSI-X interrupt");
328 xhci_free_irq(xhci);
329 pci_disable_msix(pdev);
330free_entries:
331 kfree(xhci->msix_entries);
332 xhci->msix_entries = NULL;
333 return ret;
334}
335
336/* Free any IRQs and disable MSI-X */
337static void xhci_cleanup_msix(struct xhci_hcd *xhci)
338{
339 struct usb_hcd *hcd = xhci_to_hcd(xhci);
340 struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
341
342 if (xhci->quirks & XHCI_PLAT)
343 return;
344
345 xhci_free_irq(xhci);
346
347 if (xhci->msix_entries) {
348 pci_disable_msix(pdev);
349 kfree(xhci->msix_entries);
350 xhci->msix_entries = NULL;
351 } else {
352 pci_disable_msi(pdev);
353 }
354
355 hcd->msix_enabled = 0;
356 return;
357}
358
359static void __maybe_unused xhci_msix_sync_irqs(struct xhci_hcd *xhci)
360{
361 int i;
362
363 if (xhci->msix_entries) {
364 for (i = 0; i < xhci->msix_count; i++)
365 synchronize_irq(xhci->msix_entries[i].vector);
366 }
367}
368
369static int xhci_try_enable_msi(struct usb_hcd *hcd)
370{
371 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
372 struct pci_dev *pdev;
373 int ret;
374
375 /* The xhci platform device has set up IRQs through usb_add_hcd. */
376 if (xhci->quirks & XHCI_PLAT)
377 return 0;
378
379 pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
380 /*
381 * Some Fresco Logic host controllers advertise MSI, but fail to
382 * generate interrupts. Don't even try to enable MSI.
383 */
384 if (xhci->quirks & XHCI_BROKEN_MSI)
385 goto legacy_irq;
386
387 /* unregister the legacy interrupt */
388 if (hcd->irq)
389 free_irq(hcd->irq, hcd);
390 hcd->irq = 0;
391
392 ret = xhci_setup_msix(xhci);
393 if (ret)
394 /* fall back to msi*/
395 ret = xhci_setup_msi(xhci);
396
397 if (!ret)
398 /* hcd->irq is 0, we have MSI */
399 return 0;
400
401 if (!pdev->irq) {
402 xhci_err(xhci, "No msi-x/msi found and no IRQ in BIOS\n");
403 return -EINVAL;
404 }
405
406 legacy_irq:
407 if (!strlen(hcd->irq_descr))
408 snprintf(hcd->irq_descr, sizeof(hcd->irq_descr), "%s:usb%d",
409 hcd->driver->description, hcd->self.busnum);
410
411 /* fall back to legacy interrupt*/
412 ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED,
413 hcd->irq_descr, hcd);
414 if (ret) {
415 xhci_err(xhci, "request interrupt %d failed\n",
416 pdev->irq);
417 return ret;
418 }
419 hcd->irq = pdev->irq;
420 return 0;
421}
422
423#else
424
425static inline int xhci_try_enable_msi(struct usb_hcd *hcd)
426{
427 return 0;
428}
429
430static inline void xhci_cleanup_msix(struct xhci_hcd *xhci)
431{
432}
433
434static inline void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
435{
436}
437
438#endif
439
440static void compliance_mode_recovery(unsigned long arg)
441{
442 struct xhci_hcd *xhci;
443 struct usb_hcd *hcd;
444 u32 temp;
445 int i;
446
447 xhci = (struct xhci_hcd *)arg;
448
449 for (i = 0; i < xhci->num_usb3_ports; i++) {
450 temp = readl(xhci->usb3_ports[i]);
451 if ((temp & PORT_PLS_MASK) == USB_SS_PORT_LS_COMP_MOD) {
452 /*
453 * Compliance Mode Detected. Letting USB Core
454 * handle the Warm Reset
455 */
456 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
457 "Compliance mode detected->port %d",
458 i + 1);
459 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
460 "Attempting compliance mode recovery");
461 hcd = xhci->shared_hcd;
462
463 if (hcd->state == HC_STATE_SUSPENDED)
464 usb_hcd_resume_root_hub(hcd);
465
466 usb_hcd_poll_rh_status(hcd);
467 }
468 }
469
470 if (xhci->port_status_u0 != ((1 << xhci->num_usb3_ports)-1))
471 mod_timer(&xhci->comp_mode_recovery_timer,
472 jiffies + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
473}
474
475/*
476 * Quirk to work around issue generated by the SN65LVPE502CP USB3.0 re-driver
477 * that causes ports behind that hardware to enter compliance mode sometimes.
478 * The quirk creates a timer that polls every 2 seconds the link state of
479 * each host controller's port and recovers it by issuing a Warm reset
480 * if Compliance mode is detected, otherwise the port will become "dead" (no
481 * device connections or disconnections will be detected anymore). Becasue no
482 * status event is generated when entering compliance mode (per xhci spec),
483 * this quirk is needed on systems that have the failing hardware installed.
484 */
485static void compliance_mode_recovery_timer_init(struct xhci_hcd *xhci)
486{
487 xhci->port_status_u0 = 0;
488 setup_timer(&xhci->comp_mode_recovery_timer,
489 compliance_mode_recovery, (unsigned long)xhci);
490 xhci->comp_mode_recovery_timer.expires = jiffies +
491 msecs_to_jiffies(COMP_MODE_RCVRY_MSECS);
492
493 set_timer_slack(&xhci->comp_mode_recovery_timer,
494 msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
495 add_timer(&xhci->comp_mode_recovery_timer);
496 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
497 "Compliance mode recovery timer initialized");
498}
499
500/*
501 * This function identifies the systems that have installed the SN65LVPE502CP
502 * USB3.0 re-driver and that need the Compliance Mode Quirk.
503 * Systems:
504 * Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820
505 */
506static bool xhci_compliance_mode_recovery_timer_quirk_check(void)
507{
508 const char *dmi_product_name, *dmi_sys_vendor;
509
510 dmi_product_name = dmi_get_system_info(DMI_PRODUCT_NAME);
511 dmi_sys_vendor = dmi_get_system_info(DMI_SYS_VENDOR);
512 if (!dmi_product_name || !dmi_sys_vendor)
513 return false;
514
515 if (!(strstr(dmi_sys_vendor, "Hewlett-Packard")))
516 return false;
517
518 if (strstr(dmi_product_name, "Z420") ||
519 strstr(dmi_product_name, "Z620") ||
520 strstr(dmi_product_name, "Z820") ||
521 strstr(dmi_product_name, "Z1 Workstation"))
522 return true;
523
524 return false;
525}
526
527static int xhci_all_ports_seen_u0(struct xhci_hcd *xhci)
528{
529 return (xhci->port_status_u0 == ((1 << xhci->num_usb3_ports)-1));
530}
531
532
533/*
534 * Initialize memory for HCD and xHC (one-time init).
535 *
536 * Program the PAGESIZE register, initialize the device context array, create
537 * device contexts (?), set up a command ring segment (or two?), create event
538 * ring (one for now).
539 */
540int xhci_init(struct usb_hcd *hcd)
541{
542 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
543 int retval = 0;
544
545 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "xhci_init");
546 spin_lock_init(&xhci->lock);
547 if (xhci->hci_version == 0x95 && link_quirk) {
548 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
549 "QUIRK: Not clearing Link TRB chain bits.");
550 xhci->quirks |= XHCI_LINK_TRB_QUIRK;
551 } else {
552 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
553 "xHCI doesn't need link TRB QUIRK");
554 }
555 retval = xhci_mem_init(xhci, GFP_KERNEL);
556 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Finished xhci_init");
557
558 /* Initializing Compliance Mode Recovery Data If Needed */
559 if (xhci_compliance_mode_recovery_timer_quirk_check()) {
560 xhci->quirks |= XHCI_COMP_MODE_QUIRK;
561 compliance_mode_recovery_timer_init(xhci);
562 }
563
564 return retval;
565}
566
567/*-------------------------------------------------------------------------*/
568
569
570static int xhci_run_finished(struct xhci_hcd *xhci)
571{
572 if (xhci_start(xhci)) {
573 xhci_halt(xhci);
574 return -ENODEV;
575 }
576 xhci->shared_hcd->state = HC_STATE_RUNNING;
577 xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
578
579 if (xhci->quirks & XHCI_NEC_HOST)
580 xhci_ring_cmd_db(xhci);
581
582 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
583 "Finished xhci_run for USB3 roothub");
584 return 0;
585}
586
587/*
588 * Start the HC after it was halted.
589 *
590 * This function is called by the USB core when the HC driver is added.
591 * Its opposite is xhci_stop().
592 *
593 * xhci_init() must be called once before this function can be called.
594 * Reset the HC, enable device slot contexts, program DCBAAP, and
595 * set command ring pointer and event ring pointer.
596 *
597 * Setup MSI-X vectors and enable interrupts.
598 */
599int xhci_run(struct usb_hcd *hcd)
600{
601 u32 temp;
602 u64 temp_64;
603 int ret;
604 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
605
606 /* Start the xHCI host controller running only after the USB 2.0 roothub
607 * is setup.
608 */
609
610 hcd->uses_new_polling = 1;
611 if (!usb_hcd_is_primary_hcd(hcd))
612 return xhci_run_finished(xhci);
613
614 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "xhci_run");
615
616 ret = xhci_try_enable_msi(hcd);
617 if (ret)
618 return ret;
619
620 xhci_dbg(xhci, "Command ring memory map follows:\n");
621 xhci_debug_ring(xhci, xhci->cmd_ring);
622 xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
623 xhci_dbg_cmd_ptrs(xhci);
624
625 xhci_dbg(xhci, "ERST memory map follows:\n");
626 xhci_dbg_erst(xhci, &xhci->erst);
627 xhci_dbg(xhci, "Event ring:\n");
628 xhci_debug_ring(xhci, xhci->event_ring);
629 xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
630 temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
631 temp_64 &= ~ERST_PTR_MASK;
632 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
633 "ERST deq = 64'h%0lx", (long unsigned int) temp_64);
634
635 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
636 "// Set the interrupt modulation register");
637 temp = readl(&xhci->ir_set->irq_control);
638 temp &= ~ER_IRQ_INTERVAL_MASK;
639 /*
640 * the increment interval is 8 times as much as that defined
641 * in xHCI spec on MTK's controller
642 */
643 temp |= (u32) ((xhci->quirks & XHCI_MTK_HOST) ? 20 : 160);
644 writel(temp, &xhci->ir_set->irq_control);
645
646 /* Set the HCD state before we enable the irqs */
647 temp = readl(&xhci->op_regs->command);
648 temp |= (CMD_EIE);
649 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
650 "// Enable interrupts, cmd = 0x%x.", temp);
651 writel(temp, &xhci->op_regs->command);
652
653 temp = readl(&xhci->ir_set->irq_pending);
654 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
655 "// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
656 xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
657 writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
658 xhci_print_ir_set(xhci, 0);
659
660 if (xhci->quirks & XHCI_NEC_HOST) {
661 struct xhci_command *command;
662 command = xhci_alloc_command(xhci, false, false, GFP_KERNEL);
663 if (!command)
664 return -ENOMEM;
665 xhci_queue_vendor_command(xhci, command, 0, 0, 0,
666 TRB_TYPE(TRB_NEC_GET_FW));
667 }
668 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
669 "Finished xhci_run for USB2 roothub");
670 return 0;
671}
672EXPORT_SYMBOL_GPL(xhci_run);
673
674/*
675 * Stop xHCI driver.
676 *
677 * This function is called by the USB core when the HC driver is removed.
678 * Its opposite is xhci_run().
679 *
680 * Disable device contexts, disable IRQs, and quiesce the HC.
681 * Reset the HC, finish any completed transactions, and cleanup memory.
682 */
683void xhci_stop(struct usb_hcd *hcd)
684{
685 u32 temp;
686 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
687
688 if (xhci->xhc_state & XHCI_STATE_HALTED)
689 return;
690
691 mutex_lock(&xhci->mutex);
692 spin_lock_irq(&xhci->lock);
693 xhci->xhc_state |= XHCI_STATE_HALTED;
694 xhci->cmd_ring_state = CMD_RING_STATE_STOPPED;
695
696 /* Make sure the xHC is halted for a USB3 roothub
697 * (xhci_stop() could be called as part of failed init).
698 */
699 xhci_halt(xhci);
700 xhci_reset(xhci);
701 spin_unlock_irq(&xhci->lock);
702
703 xhci_cleanup_msix(xhci);
704
705 /* Deleting Compliance Mode Recovery Timer */
706 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
707 (!(xhci_all_ports_seen_u0(xhci)))) {
708 del_timer_sync(&xhci->comp_mode_recovery_timer);
709 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
710 "%s: compliance mode recovery timer deleted",
711 __func__);
712 }
713
714 if (xhci->quirks & XHCI_AMD_PLL_FIX)
715 usb_amd_dev_put();
716
717 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
718 "// Disabling event ring interrupts");
719 temp = readl(&xhci->op_regs->status);
720 writel(temp & ~STS_EINT, &xhci->op_regs->status);
721 temp = readl(&xhci->ir_set->irq_pending);
722 writel(ER_IRQ_DISABLE(temp), &xhci->ir_set->irq_pending);
723 xhci_print_ir_set(xhci, 0);
724
725 xhci_dbg_trace(xhci, trace_xhci_dbg_init, "cleaning up memory");
726 xhci_mem_cleanup(xhci);
727 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
728 "xhci_stop completed - status = %x",
729 readl(&xhci->op_regs->status));
730 mutex_unlock(&xhci->mutex);
731}
732
733/*
734 * Shutdown HC (not bus-specific)
735 *
736 * This is called when the machine is rebooting or halting. We assume that the
737 * machine will be powered off, and the HC's internal state will be reset.
738 * Don't bother to free memory.
739 *
740 * This will only ever be called with the main usb_hcd (the USB3 roothub).
741 */
742void xhci_shutdown(struct usb_hcd *hcd)
743{
744 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
745
746 if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
747 usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
748
749 spin_lock_irq(&xhci->lock);
750 xhci_halt(xhci);
751 /* Workaround for spurious wakeups at shutdown with HSW */
752 if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
753 xhci_reset(xhci);
754 spin_unlock_irq(&xhci->lock);
755
756 xhci_cleanup_msix(xhci);
757
758 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
759 "xhci_shutdown completed - status = %x",
760 readl(&xhci->op_regs->status));
761
762 /* Yet another workaround for spurious wakeups at shutdown with HSW */
763 if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
764 pci_set_power_state(to_pci_dev(hcd->self.controller), PCI_D3hot);
765}
766
767#ifdef CONFIG_PM
768static void xhci_save_registers(struct xhci_hcd *xhci)
769{
770 xhci->s3.command = readl(&xhci->op_regs->command);
771 xhci->s3.dev_nt = readl(&xhci->op_regs->dev_notification);
772 xhci->s3.dcbaa_ptr = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
773 xhci->s3.config_reg = readl(&xhci->op_regs->config_reg);
774 xhci->s3.erst_size = readl(&xhci->ir_set->erst_size);
775 xhci->s3.erst_base = xhci_read_64(xhci, &xhci->ir_set->erst_base);
776 xhci->s3.erst_dequeue = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
777 xhci->s3.irq_pending = readl(&xhci->ir_set->irq_pending);
778 xhci->s3.irq_control = readl(&xhci->ir_set->irq_control);
779}
780
781static void xhci_restore_registers(struct xhci_hcd *xhci)
782{
783 writel(xhci->s3.command, &xhci->op_regs->command);
784 writel(xhci->s3.dev_nt, &xhci->op_regs->dev_notification);
785 xhci_write_64(xhci, xhci->s3.dcbaa_ptr, &xhci->op_regs->dcbaa_ptr);
786 writel(xhci->s3.config_reg, &xhci->op_regs->config_reg);
787 writel(xhci->s3.erst_size, &xhci->ir_set->erst_size);
788 xhci_write_64(xhci, xhci->s3.erst_base, &xhci->ir_set->erst_base);
789 xhci_write_64(xhci, xhci->s3.erst_dequeue, &xhci->ir_set->erst_dequeue);
790 writel(xhci->s3.irq_pending, &xhci->ir_set->irq_pending);
791 writel(xhci->s3.irq_control, &xhci->ir_set->irq_control);
792}
793
794static void xhci_set_cmd_ring_deq(struct xhci_hcd *xhci)
795{
796 u64 val_64;
797
798 /* step 2: initialize command ring buffer */
799 val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring);
800 val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) |
801 (xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
802 xhci->cmd_ring->dequeue) &
803 (u64) ~CMD_RING_RSVD_BITS) |
804 xhci->cmd_ring->cycle_state;
805 xhci_dbg_trace(xhci, trace_xhci_dbg_init,
806 "// Setting command ring address to 0x%llx",
807 (long unsigned long) val_64);
808 xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring);
809}
810
811/*
812 * The whole command ring must be cleared to zero when we suspend the host.
813 *
814 * The host doesn't save the command ring pointer in the suspend well, so we
815 * need to re-program it on resume. Unfortunately, the pointer must be 64-byte
816 * aligned, because of the reserved bits in the command ring dequeue pointer
817 * register. Therefore, we can't just set the dequeue pointer back in the
818 * middle of the ring (TRBs are 16-byte aligned).
819 */
820static void xhci_clear_command_ring(struct xhci_hcd *xhci)
821{
822 struct xhci_ring *ring;
823 struct xhci_segment *seg;
824
825 ring = xhci->cmd_ring;
826 seg = ring->deq_seg;
827 do {
828 memset(seg->trbs, 0,
829 sizeof(union xhci_trb) * (TRBS_PER_SEGMENT - 1));
830 seg->trbs[TRBS_PER_SEGMENT - 1].link.control &=
831 cpu_to_le32(~TRB_CYCLE);
832 seg = seg->next;
833 } while (seg != ring->deq_seg);
834
835 /* Reset the software enqueue and dequeue pointers */
836 ring->deq_seg = ring->first_seg;
837 ring->dequeue = ring->first_seg->trbs;
838 ring->enq_seg = ring->deq_seg;
839 ring->enqueue = ring->dequeue;
840
841 ring->num_trbs_free = ring->num_segs * (TRBS_PER_SEGMENT - 1) - 1;
842 /*
843 * Ring is now zeroed, so the HW should look for change of ownership
844 * when the cycle bit is set to 1.
845 */
846 ring->cycle_state = 1;
847
848 /*
849 * Reset the hardware dequeue pointer.
850 * Yes, this will need to be re-written after resume, but we're paranoid
851 * and want to make sure the hardware doesn't access bogus memory
852 * because, say, the BIOS or an SMI started the host without changing
853 * the command ring pointers.
854 */
855 xhci_set_cmd_ring_deq(xhci);
856}
857
858static void xhci_disable_port_wake_on_bits(struct xhci_hcd *xhci)
859{
860 int port_index;
861 __le32 __iomem **port_array;
862 unsigned long flags;
863 u32 t1, t2;
864
865 spin_lock_irqsave(&xhci->lock, flags);
866
867 /* disble usb3 ports Wake bits*/
868 port_index = xhci->num_usb3_ports;
869 port_array = xhci->usb3_ports;
870 while (port_index--) {
871 t1 = readl(port_array[port_index]);
872 t1 = xhci_port_state_to_neutral(t1);
873 t2 = t1 & ~PORT_WAKE_BITS;
874 if (t1 != t2)
875 writel(t2, port_array[port_index]);
876 }
877
878 /* disble usb2 ports Wake bits*/
879 port_index = xhci->num_usb2_ports;
880 port_array = xhci->usb2_ports;
881 while (port_index--) {
882 t1 = readl(port_array[port_index]);
883 t1 = xhci_port_state_to_neutral(t1);
884 t2 = t1 & ~PORT_WAKE_BITS;
885 if (t1 != t2)
886 writel(t2, port_array[port_index]);
887 }
888
889 spin_unlock_irqrestore(&xhci->lock, flags);
890}
891
892/*
893 * Stop HC (not bus-specific)
894 *
895 * This is called when the machine transition into S3/S4 mode.
896 *
897 */
898int xhci_suspend(struct xhci_hcd *xhci, bool do_wakeup)
899{
900 int rc = 0;
901 unsigned int delay = XHCI_MAX_HALT_USEC;
902 struct usb_hcd *hcd = xhci_to_hcd(xhci);
903 u32 command;
904
905 if (!hcd->state)
906 return 0;
907
908 if (hcd->state != HC_STATE_SUSPENDED ||
909 xhci->shared_hcd->state != HC_STATE_SUSPENDED)
910 return -EINVAL;
911
912 /* Clear root port wake on bits if wakeup not allowed. */
913 if (!do_wakeup)
914 xhci_disable_port_wake_on_bits(xhci);
915
916 /* Don't poll the roothubs on bus suspend. */
917 xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
918 clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
919 del_timer_sync(&hcd->rh_timer);
920 clear_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags);
921 del_timer_sync(&xhci->shared_hcd->rh_timer);
922
923 spin_lock_irq(&xhci->lock);
924 clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
925 clear_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
926 /* step 1: stop endpoint */
927 /* skipped assuming that port suspend has done */
928
929 /* step 2: clear Run/Stop bit */
930 command = readl(&xhci->op_regs->command);
931 command &= ~CMD_RUN;
932 writel(command, &xhci->op_regs->command);
933
934 /* Some chips from Fresco Logic need an extraordinary delay */
935 delay *= (xhci->quirks & XHCI_SLOW_SUSPEND) ? 10 : 1;
936
937 if (xhci_handshake(&xhci->op_regs->status,
938 STS_HALT, STS_HALT, delay)) {
939 xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
940 spin_unlock_irq(&xhci->lock);
941 return -ETIMEDOUT;
942 }
943 xhci_clear_command_ring(xhci);
944
945 /* step 3: save registers */
946 xhci_save_registers(xhci);
947
948 /* step 4: set CSS flag */
949 command = readl(&xhci->op_regs->command);
950 command |= CMD_CSS;
951 writel(command, &xhci->op_regs->command);
952 if (xhci_handshake(&xhci->op_regs->status,
953 STS_SAVE, 0, 10 * 1000)) {
954 xhci_warn(xhci, "WARN: xHC save state timeout\n");
955 spin_unlock_irq(&xhci->lock);
956 return -ETIMEDOUT;
957 }
958 spin_unlock_irq(&xhci->lock);
959
960 /*
961 * Deleting Compliance Mode Recovery Timer because the xHCI Host
962 * is about to be suspended.
963 */
964 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
965 (!(xhci_all_ports_seen_u0(xhci)))) {
966 del_timer_sync(&xhci->comp_mode_recovery_timer);
967 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
968 "%s: compliance mode recovery timer deleted",
969 __func__);
970 }
971
972 /* step 5: remove core well power */
973 /* synchronize irq when using MSI-X */
974 xhci_msix_sync_irqs(xhci);
975
976 return rc;
977}
978EXPORT_SYMBOL_GPL(xhci_suspend);
979
980/*
981 * start xHC (not bus-specific)
982 *
983 * This is called when the machine transition from S3/S4 mode.
984 *
985 */
986int xhci_resume(struct xhci_hcd *xhci, bool hibernated)
987{
988 u32 command, temp = 0, status;
989 struct usb_hcd *hcd = xhci_to_hcd(xhci);
990 struct usb_hcd *secondary_hcd;
991 int retval = 0;
992 bool comp_timer_running = false;
993
994 if (!hcd->state)
995 return 0;
996
997 /* Wait a bit if either of the roothubs need to settle from the
998 * transition into bus suspend.
999 */
1000 if (time_before(jiffies, xhci->bus_state[0].next_statechange) ||
1001 time_before(jiffies,
1002 xhci->bus_state[1].next_statechange))
1003 msleep(100);
1004
1005 set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
1006 set_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
1007
1008 spin_lock_irq(&xhci->lock);
1009 if (xhci->quirks & XHCI_RESET_ON_RESUME)
1010 hibernated = true;
1011
1012 if (!hibernated) {
1013 /* step 1: restore register */
1014 xhci_restore_registers(xhci);
1015 /* step 2: initialize command ring buffer */
1016 xhci_set_cmd_ring_deq(xhci);
1017 /* step 3: restore state and start state*/
1018 /* step 3: set CRS flag */
1019 command = readl(&xhci->op_regs->command);
1020 command |= CMD_CRS;
1021 writel(command, &xhci->op_regs->command);
1022 if (xhci_handshake(&xhci->op_regs->status,
1023 STS_RESTORE, 0, 10 * 1000)) {
1024 xhci_warn(xhci, "WARN: xHC restore state timeout\n");
1025 spin_unlock_irq(&xhci->lock);
1026 return -ETIMEDOUT;
1027 }
1028 temp = readl(&xhci->op_regs->status);
1029 }
1030
1031 /* If restore operation fails, re-initialize the HC during resume */
1032 if ((temp & STS_SRE) || hibernated) {
1033
1034 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
1035 !(xhci_all_ports_seen_u0(xhci))) {
1036 del_timer_sync(&xhci->comp_mode_recovery_timer);
1037 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
1038 "Compliance Mode Recovery Timer deleted!");
1039 }
1040
1041 /* Let the USB core know _both_ roothubs lost power. */
1042 usb_root_hub_lost_power(xhci->main_hcd->self.root_hub);
1043 usb_root_hub_lost_power(xhci->shared_hcd->self.root_hub);
1044
1045 xhci_dbg(xhci, "Stop HCD\n");
1046 xhci_halt(xhci);
1047 xhci_reset(xhci);
1048 spin_unlock_irq(&xhci->lock);
1049 xhci_cleanup_msix(xhci);
1050
1051 xhci_dbg(xhci, "// Disabling event ring interrupts\n");
1052 temp = readl(&xhci->op_regs->status);
1053 writel(temp & ~STS_EINT, &xhci->op_regs->status);
1054 temp = readl(&xhci->ir_set->irq_pending);
1055 writel(ER_IRQ_DISABLE(temp), &xhci->ir_set->irq_pending);
1056 xhci_print_ir_set(xhci, 0);
1057
1058 xhci_dbg(xhci, "cleaning up memory\n");
1059 xhci_mem_cleanup(xhci);
1060 xhci_dbg(xhci, "xhci_stop completed - status = %x\n",
1061 readl(&xhci->op_regs->status));
1062
1063 /* USB core calls the PCI reinit and start functions twice:
1064 * first with the primary HCD, and then with the secondary HCD.
1065 * If we don't do the same, the host will never be started.
1066 */
1067 if (!usb_hcd_is_primary_hcd(hcd))
1068 secondary_hcd = hcd;
1069 else
1070 secondary_hcd = xhci->shared_hcd;
1071
1072 xhci_dbg(xhci, "Initialize the xhci_hcd\n");
1073 retval = xhci_init(hcd->primary_hcd);
1074 if (retval)
1075 return retval;
1076 comp_timer_running = true;
1077
1078 xhci_dbg(xhci, "Start the primary HCD\n");
1079 retval = xhci_run(hcd->primary_hcd);
1080 if (!retval) {
1081 xhci_dbg(xhci, "Start the secondary HCD\n");
1082 retval = xhci_run(secondary_hcd);
1083 }
1084 hcd->state = HC_STATE_SUSPENDED;
1085 xhci->shared_hcd->state = HC_STATE_SUSPENDED;
1086 goto done;
1087 }
1088
1089 /* step 4: set Run/Stop bit */
1090 command = readl(&xhci->op_regs->command);
1091 command |= CMD_RUN;
1092 writel(command, &xhci->op_regs->command);
1093 xhci_handshake(&xhci->op_regs->status, STS_HALT,
1094 0, 250 * 1000);
1095
1096 /* step 5: walk topology and initialize portsc,
1097 * portpmsc and portli
1098 */
1099 /* this is done in bus_resume */
1100
1101 /* step 6: restart each of the previously
1102 * Running endpoints by ringing their doorbells
1103 */
1104
1105 spin_unlock_irq(&xhci->lock);
1106
1107 done:
1108 if (retval == 0) {
1109 /* Resume root hubs only when have pending events. */
1110 status = readl(&xhci->op_regs->status);
1111 if (status & STS_EINT) {
1112 usb_hcd_resume_root_hub(xhci->shared_hcd);
1113 usb_hcd_resume_root_hub(hcd);
1114 }
1115 }
1116
1117 /*
1118 * If system is subject to the Quirk, Compliance Mode Timer needs to
1119 * be re-initialized Always after a system resume. Ports are subject
1120 * to suffer the Compliance Mode issue again. It doesn't matter if
1121 * ports have entered previously to U0 before system's suspension.
1122 */
1123 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && !comp_timer_running)
1124 compliance_mode_recovery_timer_init(xhci);
1125
1126 /* Re-enable port polling. */
1127 xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
1128 set_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags);
1129 usb_hcd_poll_rh_status(xhci->shared_hcd);
1130 set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
1131 usb_hcd_poll_rh_status(hcd);
1132
1133 return retval;
1134}
1135EXPORT_SYMBOL_GPL(xhci_resume);
1136#endif /* CONFIG_PM */
1137
1138/*-------------------------------------------------------------------------*/
1139
1140/**
1141 * xhci_get_endpoint_index - Used for passing endpoint bitmasks between the core and
1142 * HCDs. Find the index for an endpoint given its descriptor. Use the return
1143 * value to right shift 1 for the bitmask.
1144 *
1145 * Index = (epnum * 2) + direction - 1,
1146 * where direction = 0 for OUT, 1 for IN.
1147 * For control endpoints, the IN index is used (OUT index is unused), so
1148 * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2)
1149 */
1150unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc)
1151{
1152 unsigned int index;
1153 if (usb_endpoint_xfer_control(desc))
1154 index = (unsigned int) (usb_endpoint_num(desc)*2);
1155 else
1156 index = (unsigned int) (usb_endpoint_num(desc)*2) +
1157 (usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
1158 return index;
1159}
1160
1161/* The reverse operation to xhci_get_endpoint_index. Calculate the USB endpoint
1162 * address from the XHCI endpoint index.
1163 */
1164unsigned int xhci_get_endpoint_address(unsigned int ep_index)
1165{
1166 unsigned int number = DIV_ROUND_UP(ep_index, 2);
1167 unsigned int direction = ep_index % 2 ? USB_DIR_OUT : USB_DIR_IN;
1168 return direction | number;
1169}
1170
1171/* Find the flag for this endpoint (for use in the control context). Use the
1172 * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
1173 * bit 1, etc.
1174 */
1175unsigned int xhci_get_endpoint_flag(struct usb_endpoint_descriptor *desc)
1176{
1177 return 1 << (xhci_get_endpoint_index(desc) + 1);
1178}
1179
1180/* Find the flag for this endpoint (for use in the control context). Use the
1181 * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
1182 * bit 1, etc.
1183 */
1184unsigned int xhci_get_endpoint_flag_from_index(unsigned int ep_index)
1185{
1186 return 1 << (ep_index + 1);
1187}
1188
1189/* Compute the last valid endpoint context index. Basically, this is the
1190 * endpoint index plus one. For slot contexts with more than valid endpoint,
1191 * we find the most significant bit set in the added contexts flags.
1192 * e.g. ep 1 IN (with epnum 0x81) => added_ctxs = 0b1000
1193 * fls(0b1000) = 4, but the endpoint context index is 3, so subtract one.
1194 */
1195unsigned int xhci_last_valid_endpoint(u32 added_ctxs)
1196{
1197 return fls(added_ctxs) - 1;
1198}
1199
1200/* Returns 1 if the arguments are OK;
1201 * returns 0 this is a root hub; returns -EINVAL for NULL pointers.
1202 */
1203static int xhci_check_args(struct usb_hcd *hcd, struct usb_device *udev,
1204 struct usb_host_endpoint *ep, int check_ep, bool check_virt_dev,
1205 const char *func) {
1206 struct xhci_hcd *xhci;
1207 struct xhci_virt_device *virt_dev;
1208
1209 if (!hcd || (check_ep && !ep) || !udev) {
1210 pr_debug("xHCI %s called with invalid args\n", func);
1211 return -EINVAL;
1212 }
1213 if (!udev->parent) {
1214 pr_debug("xHCI %s called for root hub\n", func);
1215 return 0;
1216 }
1217
1218 xhci = hcd_to_xhci(hcd);
1219 if (check_virt_dev) {
1220 if (!udev->slot_id || !xhci->devs[udev->slot_id]) {
1221 xhci_dbg(xhci, "xHCI %s called with unaddressed device\n",
1222 func);
1223 return -EINVAL;
1224 }
1225
1226 virt_dev = xhci->devs[udev->slot_id];
1227 if (virt_dev->udev != udev) {
1228 xhci_dbg(xhci, "xHCI %s called with udev and "
1229 "virt_dev does not match\n", func);
1230 return -EINVAL;
1231 }
1232 }
1233
1234 if (xhci->xhc_state & XHCI_STATE_HALTED)
1235 return -ENODEV;
1236
1237 return 1;
1238}
1239
1240static int xhci_configure_endpoint(struct xhci_hcd *xhci,
1241 struct usb_device *udev, struct xhci_command *command,
1242 bool ctx_change, bool must_succeed);
1243
1244/*
1245 * Full speed devices may have a max packet size greater than 8 bytes, but the
1246 * USB core doesn't know that until it reads the first 8 bytes of the
1247 * descriptor. If the usb_device's max packet size changes after that point,
1248 * we need to issue an evaluate context command and wait on it.
1249 */
1250static int xhci_check_maxpacket(struct xhci_hcd *xhci, unsigned int slot_id,
1251 unsigned int ep_index, struct urb *urb)
1252{
1253 struct xhci_container_ctx *out_ctx;
1254 struct xhci_input_control_ctx *ctrl_ctx;
1255 struct xhci_ep_ctx *ep_ctx;
1256 struct xhci_command *command;
1257 int max_packet_size;
1258 int hw_max_packet_size;
1259 int ret = 0;
1260
1261 out_ctx = xhci->devs[slot_id]->out_ctx;
1262 ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
1263 hw_max_packet_size = MAX_PACKET_DECODED(le32_to_cpu(ep_ctx->ep_info2));
1264 max_packet_size = usb_endpoint_maxp(&urb->dev->ep0.desc);
1265 if (hw_max_packet_size != max_packet_size) {
1266 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
1267 "Max Packet Size for ep 0 changed.");
1268 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
1269 "Max packet size in usb_device = %d",
1270 max_packet_size);
1271 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
1272 "Max packet size in xHCI HW = %d",
1273 hw_max_packet_size);
1274 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
1275 "Issuing evaluate context command.");
1276
1277 /* Set up the input context flags for the command */
1278 /* FIXME: This won't work if a non-default control endpoint
1279 * changes max packet sizes.
1280 */
1281
1282 command = xhci_alloc_command(xhci, false, true, GFP_KERNEL);
1283 if (!command)
1284 return -ENOMEM;
1285
1286 command->in_ctx = xhci->devs[slot_id]->in_ctx;
1287 ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
1288 if (!ctrl_ctx) {
1289 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
1290 __func__);
1291 ret = -ENOMEM;
1292 goto command_cleanup;
1293 }
1294 /* Set up the modified control endpoint 0 */
1295 xhci_endpoint_copy(xhci, xhci->devs[slot_id]->in_ctx,
1296 xhci->devs[slot_id]->out_ctx, ep_index);
1297
1298 ep_ctx = xhci_get_ep_ctx(xhci, command->in_ctx, ep_index);
1299 ep_ctx->ep_info2 &= cpu_to_le32(~MAX_PACKET_MASK);
1300 ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet_size));
1301
1302 ctrl_ctx->add_flags = cpu_to_le32(EP0_FLAG);
1303 ctrl_ctx->drop_flags = 0;
1304
1305 xhci_dbg(xhci, "Slot %d input context\n", slot_id);
1306 xhci_dbg_ctx(xhci, command->in_ctx, ep_index);
1307 xhci_dbg(xhci, "Slot %d output context\n", slot_id);
1308 xhci_dbg_ctx(xhci, out_ctx, ep_index);
1309
1310 ret = xhci_configure_endpoint(xhci, urb->dev, command,
1311 true, false);
1312
1313 /* Clean up the input context for later use by bandwidth
1314 * functions.
1315 */
1316 ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG);
1317command_cleanup:
1318 kfree(command->completion);
1319 kfree(command);
1320 }
1321 return ret;
1322}
1323
1324/*
1325 * non-error returns are a promise to giveback() the urb later
1326 * we drop ownership so next owner (or urb unlink) can get it
1327 */
1328int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags)
1329{
1330 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
1331 struct xhci_td *buffer;
1332 unsigned long flags;
1333 int ret = 0;
1334 unsigned int slot_id, ep_index;
1335 struct urb_priv *urb_priv;
1336 int size, i;
1337
1338 if (!urb || xhci_check_args(hcd, urb->dev, urb->ep,
1339 true, true, __func__) <= 0)
1340 return -EINVAL;
1341
1342 slot_id = urb->dev->slot_id;
1343 ep_index = xhci_get_endpoint_index(&urb->ep->desc);
1344
1345 if (!HCD_HW_ACCESSIBLE(hcd)) {
1346 if (!in_interrupt())
1347 xhci_dbg(xhci, "urb submitted during PCI suspend\n");
1348 ret = -ESHUTDOWN;
1349 goto exit;
1350 }
1351
1352 if (usb_endpoint_xfer_isoc(&urb->ep->desc))
1353 size = urb->number_of_packets;
1354 else if (usb_endpoint_is_bulk_out(&urb->ep->desc) &&
1355 urb->transfer_buffer_length > 0 &&
1356 urb->transfer_flags & URB_ZERO_PACKET &&
1357 !(urb->transfer_buffer_length % usb_endpoint_maxp(&urb->ep->desc)))
1358 size = 2;
1359 else
1360 size = 1;
1361
1362 urb_priv = kzalloc(sizeof(struct urb_priv) +
1363 size * sizeof(struct xhci_td *), mem_flags);
1364 if (!urb_priv)
1365 return -ENOMEM;
1366
1367 buffer = kzalloc(size * sizeof(struct xhci_td), mem_flags);
1368 if (!buffer) {
1369 kfree(urb_priv);
1370 return -ENOMEM;
1371 }
1372
1373 for (i = 0; i < size; i++) {
1374 urb_priv->td[i] = buffer;
1375 buffer++;
1376 }
1377
1378 urb_priv->length = size;
1379 urb_priv->td_cnt = 0;
1380 urb->hcpriv = urb_priv;
1381
1382 if (usb_endpoint_xfer_control(&urb->ep->desc)) {
1383 /* Check to see if the max packet size for the default control
1384 * endpoint changed during FS device enumeration
1385 */
1386 if (urb->dev->speed == USB_SPEED_FULL) {
1387 ret = xhci_check_maxpacket(xhci, slot_id,
1388 ep_index, urb);
1389 if (ret < 0) {
1390 xhci_urb_free_priv(urb_priv);
1391 urb->hcpriv = NULL;
1392 return ret;
1393 }
1394 }
1395
1396 /* We have a spinlock and interrupts disabled, so we must pass
1397 * atomic context to this function, which may allocate memory.
1398 */
1399 spin_lock_irqsave(&xhci->lock, flags);
1400 if (xhci->xhc_state & XHCI_STATE_DYING)
1401 goto dying;
1402 ret = xhci_queue_ctrl_tx(xhci, GFP_ATOMIC, urb,
1403 slot_id, ep_index);
1404 if (ret)
1405 goto free_priv;
1406 spin_unlock_irqrestore(&xhci->lock, flags);
1407 } else if (usb_endpoint_xfer_bulk(&urb->ep->desc)) {
1408 spin_lock_irqsave(&xhci->lock, flags);
1409 if (xhci->xhc_state & XHCI_STATE_DYING)
1410 goto dying;
1411 if (xhci->devs[slot_id]->eps[ep_index].ep_state &
1412 EP_GETTING_STREAMS) {
1413 xhci_warn(xhci, "WARN: Can't enqueue URB while bulk ep "
1414 "is transitioning to using streams.\n");
1415 ret = -EINVAL;
1416 } else if (xhci->devs[slot_id]->eps[ep_index].ep_state &
1417 EP_GETTING_NO_STREAMS) {
1418 xhci_warn(xhci, "WARN: Can't enqueue URB while bulk ep "
1419 "is transitioning to "
1420 "not having streams.\n");
1421 ret = -EINVAL;
1422 } else {
1423 ret = xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb,
1424 slot_id, ep_index);
1425 }
1426 if (ret)
1427 goto free_priv;
1428 spin_unlock_irqrestore(&xhci->lock, flags);
1429 } else if (usb_endpoint_xfer_int(&urb->ep->desc)) {
1430 spin_lock_irqsave(&xhci->lock, flags);
1431 if (xhci->xhc_state & XHCI_STATE_DYING)
1432 goto dying;
1433 ret = xhci_queue_intr_tx(xhci, GFP_ATOMIC, urb,
1434 slot_id, ep_index);
1435 if (ret)
1436 goto free_priv;
1437 spin_unlock_irqrestore(&xhci->lock, flags);
1438 } else {
1439 spin_lock_irqsave(&xhci->lock, flags);
1440 if (xhci->xhc_state & XHCI_STATE_DYING)
1441 goto dying;
1442 ret = xhci_queue_isoc_tx_prepare(xhci, GFP_ATOMIC, urb,
1443 slot_id, ep_index);
1444 if (ret)
1445 goto free_priv;
1446 spin_unlock_irqrestore(&xhci->lock, flags);
1447 }
1448exit:
1449 return ret;
1450dying:
1451 xhci_dbg(xhci, "Ep 0x%x: URB %p submitted for "
1452 "non-responsive xHCI host.\n",
1453 urb->ep->desc.bEndpointAddress, urb);
1454 ret = -ESHUTDOWN;
1455free_priv:
1456 xhci_urb_free_priv(urb_priv);
1457 urb->hcpriv = NULL;
1458 spin_unlock_irqrestore(&xhci->lock, flags);
1459 return ret;
1460}
1461
1462/* Get the right ring for the given URB.
1463 * If the endpoint supports streams, boundary check the URB's stream ID.
1464 * If the endpoint doesn't support streams, return the singular endpoint ring.
1465 */
1466static struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci,
1467 struct urb *urb)
1468{
1469 unsigned int slot_id;
1470 unsigned int ep_index;
1471 unsigned int stream_id;
1472 struct xhci_virt_ep *ep;
1473
1474 slot_id = urb->dev->slot_id;
1475 ep_index = xhci_get_endpoint_index(&urb->ep->desc);
1476 stream_id = urb->stream_id;
1477 ep = &xhci->devs[slot_id]->eps[ep_index];
1478 /* Common case: no streams */
1479 if (!(ep->ep_state & EP_HAS_STREAMS))
1480 return ep->ring;
1481
1482 if (stream_id == 0) {
1483 xhci_warn(xhci,
1484 "WARN: Slot ID %u, ep index %u has streams, "
1485 "but URB has no stream ID.\n",
1486 slot_id, ep_index);
1487 return NULL;
1488 }
1489
1490 if (stream_id < ep->stream_info->num_streams)
1491 return ep->stream_info->stream_rings[stream_id];
1492
1493 xhci_warn(xhci,
1494 "WARN: Slot ID %u, ep index %u has "
1495 "stream IDs 1 to %u allocated, "
1496 "but stream ID %u is requested.\n",
1497 slot_id, ep_index,
1498 ep->stream_info->num_streams - 1,
1499 stream_id);
1500 return NULL;
1501}
1502
1503/*
1504 * Remove the URB's TD from the endpoint ring. This may cause the HC to stop
1505 * USB transfers, potentially stopping in the middle of a TRB buffer. The HC
1506 * should pick up where it left off in the TD, unless a Set Transfer Ring
1507 * Dequeue Pointer is issued.
1508 *
1509 * The TRBs that make up the buffers for the canceled URB will be "removed" from
1510 * the ring. Since the ring is a contiguous structure, they can't be physically
1511 * removed. Instead, there are two options:
1512 *
1513 * 1) If the HC is in the middle of processing the URB to be canceled, we
1514 * simply move the ring's dequeue pointer past those TRBs using the Set
1515 * Transfer Ring Dequeue Pointer command. This will be the common case,
1516 * when drivers timeout on the last submitted URB and attempt to cancel.
1517 *
1518 * 2) If the HC is in the middle of a different TD, we turn the TRBs into a
1519 * series of 1-TRB transfer no-op TDs. (No-ops shouldn't be chained.) The
1520 * HC will need to invalidate the any TRBs it has cached after the stop
1521 * endpoint command, as noted in the xHCI 0.95 errata.
1522 *
1523 * 3) The TD may have completed by the time the Stop Endpoint Command
1524 * completes, so software needs to handle that case too.
1525 *
1526 * This function should protect against the TD enqueueing code ringing the
1527 * doorbell while this code is waiting for a Stop Endpoint command to complete.
1528 * It also needs to account for multiple cancellations on happening at the same
1529 * time for the same endpoint.
1530 *
1531 * Note that this function can be called in any context, or so says
1532 * usb_hcd_unlink_urb()
1533 */
1534int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
1535{
1536 unsigned long flags;
1537 int ret, i;
1538 u32 temp;
1539 struct xhci_hcd *xhci;
1540 struct urb_priv *urb_priv;
1541 struct xhci_td *td;
1542 unsigned int ep_index;
1543 struct xhci_ring *ep_ring;
1544 struct xhci_virt_ep *ep;
1545 struct xhci_command *command;
1546
1547 xhci = hcd_to_xhci(hcd);
1548 spin_lock_irqsave(&xhci->lock, flags);
1549 /* Make sure the URB hasn't completed or been unlinked already */
1550 ret = usb_hcd_check_unlink_urb(hcd, urb, status);
1551 if (ret || !urb->hcpriv)
1552 goto done;
1553 temp = readl(&xhci->op_regs->status);
1554 if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_HALTED)) {
1555 xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
1556 "HW died, freeing TD.");
1557 urb_priv = urb->hcpriv;
1558 for (i = urb_priv->td_cnt;
1559 i < urb_priv->length && xhci->devs[urb->dev->slot_id];
1560 i++) {
1561 td = urb_priv->td[i];
1562 if (!list_empty(&td->td_list))
1563 list_del_init(&td->td_list);
1564 if (!list_empty(&td->cancelled_td_list))
1565 list_del_init(&td->cancelled_td_list);
1566 }
1567
1568 usb_hcd_unlink_urb_from_ep(hcd, urb);
1569 spin_unlock_irqrestore(&xhci->lock, flags);
1570 usb_hcd_giveback_urb(hcd, urb, -ESHUTDOWN);
1571 xhci_urb_free_priv(urb_priv);
1572 return ret;
1573 }
1574 if ((xhci->xhc_state & XHCI_STATE_DYING) ||
1575 (xhci->xhc_state & XHCI_STATE_HALTED)) {
1576 xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
1577 "Ep 0x%x: URB %p to be canceled on "
1578 "non-responsive xHCI host.",
1579 urb->ep->desc.bEndpointAddress, urb);
1580 /* Let the stop endpoint command watchdog timer (which set this
1581 * state) finish cleaning up the endpoint TD lists. We must
1582 * have caught it in the middle of dropping a lock and giving
1583 * back an URB.
1584 */
1585 goto done;
1586 }
1587
1588 ep_index = xhci_get_endpoint_index(&urb->ep->desc);
1589 ep = &xhci->devs[urb->dev->slot_id]->eps[ep_index];
1590 ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
1591 if (!ep_ring) {
1592 ret = -EINVAL;
1593 goto done;
1594 }
1595
1596 urb_priv = urb->hcpriv;
1597 i = urb_priv->td_cnt;
1598 if (i < urb_priv->length)
1599 xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
1600 "Cancel URB %p, dev %s, ep 0x%x, "
1601 "starting at offset 0x%llx",
1602 urb, urb->dev->devpath,
1603 urb->ep->desc.bEndpointAddress,
1604 (unsigned long long) xhci_trb_virt_to_dma(
1605 urb_priv->td[i]->start_seg,
1606 urb_priv->td[i]->first_trb));
1607
1608 for (; i < urb_priv->length; i++) {
1609 td = urb_priv->td[i];
1610 list_add_tail(&td->cancelled_td_list, &ep->cancelled_td_list);
1611 }
1612
1613 /* Queue a stop endpoint command, but only if this is
1614 * the first cancellation to be handled.
1615 */
1616 if (!(ep->ep_state & EP_HALT_PENDING)) {
1617 command = xhci_alloc_command(xhci, false, false, GFP_ATOMIC);
1618 if (!command) {
1619 ret = -ENOMEM;
1620 goto done;
1621 }
1622 ep->ep_state |= EP_HALT_PENDING;
1623 ep->stop_cmds_pending++;
1624 ep->stop_cmd_timer.expires = jiffies +
1625 XHCI_STOP_EP_CMD_TIMEOUT * HZ;
1626 add_timer(&ep->stop_cmd_timer);
1627 xhci_queue_stop_endpoint(xhci, command, urb->dev->slot_id,
1628 ep_index, 0);
1629 xhci_ring_cmd_db(xhci);
1630 }
1631done:
1632 spin_unlock_irqrestore(&xhci->lock, flags);
1633 return ret;
1634}
1635
1636/* Drop an endpoint from a new bandwidth configuration for this device.
1637 * Only one call to this function is allowed per endpoint before
1638 * check_bandwidth() or reset_bandwidth() must be called.
1639 * A call to xhci_drop_endpoint() followed by a call to xhci_add_endpoint() will
1640 * add the endpoint to the schedule with possibly new parameters denoted by a
1641 * different endpoint descriptor in usb_host_endpoint.
1642 * A call to xhci_add_endpoint() followed by a call to xhci_drop_endpoint() is
1643 * not allowed.
1644 *
1645 * The USB core will not allow URBs to be queued to an endpoint that is being
1646 * disabled, so there's no need for mutual exclusion to protect
1647 * the xhci->devs[slot_id] structure.
1648 */
1649int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
1650 struct usb_host_endpoint *ep)
1651{
1652 struct xhci_hcd *xhci;
1653 struct xhci_container_ctx *in_ctx, *out_ctx;
1654 struct xhci_input_control_ctx *ctrl_ctx;
1655 unsigned int ep_index;
1656 struct xhci_ep_ctx *ep_ctx;
1657 u32 drop_flag;
1658 u32 new_add_flags, new_drop_flags;
1659 int ret;
1660
1661 ret = xhci_check_args(hcd, udev, ep, 1, true, __func__);
1662 if (ret <= 0)
1663 return ret;
1664 xhci = hcd_to_xhci(hcd);
1665 if (xhci->xhc_state & XHCI_STATE_DYING)
1666 return -ENODEV;
1667
1668 xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev);
1669 drop_flag = xhci_get_endpoint_flag(&ep->desc);
1670 if (drop_flag == SLOT_FLAG || drop_flag == EP0_FLAG) {
1671 xhci_dbg(xhci, "xHCI %s - can't drop slot or ep 0 %#x\n",
1672 __func__, drop_flag);
1673 return 0;
1674 }
1675
1676 in_ctx = xhci->devs[udev->slot_id]->in_ctx;
1677 out_ctx = xhci->devs[udev->slot_id]->out_ctx;
1678 ctrl_ctx = xhci_get_input_control_ctx(in_ctx);
1679 if (!ctrl_ctx) {
1680 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
1681 __func__);
1682 return 0;
1683 }
1684
1685 ep_index = xhci_get_endpoint_index(&ep->desc);
1686 ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
1687 /* If the HC already knows the endpoint is disabled,
1688 * or the HCD has noted it is disabled, ignore this request
1689 */
1690 if (((ep_ctx->ep_info & cpu_to_le32(EP_STATE_MASK)) ==
1691 cpu_to_le32(EP_STATE_DISABLED)) ||
1692 le32_to_cpu(ctrl_ctx->drop_flags) &
1693 xhci_get_endpoint_flag(&ep->desc)) {
1694 /* Do not warn when called after a usb_device_reset */
1695 if (xhci->devs[udev->slot_id]->eps[ep_index].ring != NULL)
1696 xhci_warn(xhci, "xHCI %s called with disabled ep %p\n",
1697 __func__, ep);
1698 return 0;
1699 }
1700
1701 ctrl_ctx->drop_flags |= cpu_to_le32(drop_flag);
1702 new_drop_flags = le32_to_cpu(ctrl_ctx->drop_flags);
1703
1704 ctrl_ctx->add_flags &= cpu_to_le32(~drop_flag);
1705 new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
1706
1707 xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
1708
1709 if (xhci->quirks & XHCI_MTK_HOST)
1710 xhci_mtk_drop_ep_quirk(hcd, udev, ep);
1711
1712 xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
1713 (unsigned int) ep->desc.bEndpointAddress,
1714 udev->slot_id,
1715 (unsigned int) new_drop_flags,
1716 (unsigned int) new_add_flags);
1717 return 0;
1718}
1719
1720/* Add an endpoint to a new possible bandwidth configuration for this device.
1721 * Only one call to this function is allowed per endpoint before
1722 * check_bandwidth() or reset_bandwidth() must be called.
1723 * A call to xhci_drop_endpoint() followed by a call to xhci_add_endpoint() will
1724 * add the endpoint to the schedule with possibly new parameters denoted by a
1725 * different endpoint descriptor in usb_host_endpoint.
1726 * A call to xhci_add_endpoint() followed by a call to xhci_drop_endpoint() is
1727 * not allowed.
1728 *
1729 * The USB core will not allow URBs to be queued to an endpoint until the
1730 * configuration or alt setting is installed in the device, so there's no need
1731 * for mutual exclusion to protect the xhci->devs[slot_id] structure.
1732 */
1733int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
1734 struct usb_host_endpoint *ep)
1735{
1736 struct xhci_hcd *xhci;
1737 struct xhci_container_ctx *in_ctx;
1738 unsigned int ep_index;
1739 struct xhci_input_control_ctx *ctrl_ctx;
1740 u32 added_ctxs;
1741 u32 new_add_flags, new_drop_flags;
1742 struct xhci_virt_device *virt_dev;
1743 int ret = 0;
1744
1745 ret = xhci_check_args(hcd, udev, ep, 1, true, __func__);
1746 if (ret <= 0) {
1747 /* So we won't queue a reset ep command for a root hub */
1748 ep->hcpriv = NULL;
1749 return ret;
1750 }
1751 xhci = hcd_to_xhci(hcd);
1752 if (xhci->xhc_state & XHCI_STATE_DYING)
1753 return -ENODEV;
1754
1755 added_ctxs = xhci_get_endpoint_flag(&ep->desc);
1756 if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) {
1757 /* FIXME when we have to issue an evaluate endpoint command to
1758 * deal with ep0 max packet size changing once we get the
1759 * descriptors
1760 */
1761 xhci_dbg(xhci, "xHCI %s - can't add slot or ep 0 %#x\n",
1762 __func__, added_ctxs);
1763 return 0;
1764 }
1765
1766 virt_dev = xhci->devs[udev->slot_id];
1767 in_ctx = virt_dev->in_ctx;
1768 ctrl_ctx = xhci_get_input_control_ctx(in_ctx);
1769 if (!ctrl_ctx) {
1770 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
1771 __func__);
1772 return 0;
1773 }
1774
1775 ep_index = xhci_get_endpoint_index(&ep->desc);
1776 /* If this endpoint is already in use, and the upper layers are trying
1777 * to add it again without dropping it, reject the addition.
1778 */
1779 if (virt_dev->eps[ep_index].ring &&
1780 !(le32_to_cpu(ctrl_ctx->drop_flags) & added_ctxs)) {
1781 xhci_warn(xhci, "Trying to add endpoint 0x%x "
1782 "without dropping it.\n",
1783 (unsigned int) ep->desc.bEndpointAddress);
1784 return -EINVAL;
1785 }
1786
1787 /* If the HCD has already noted the endpoint is enabled,
1788 * ignore this request.
1789 */
1790 if (le32_to_cpu(ctrl_ctx->add_flags) & added_ctxs) {
1791 xhci_warn(xhci, "xHCI %s called with enabled ep %p\n",
1792 __func__, ep);
1793 return 0;
1794 }
1795
1796 /*
1797 * Configuration and alternate setting changes must be done in
1798 * process context, not interrupt context (or so documenation
1799 * for usb_set_interface() and usb_set_configuration() claim).
1800 */
1801 if (xhci_endpoint_init(xhci, virt_dev, udev, ep, GFP_NOIO) < 0) {
1802 dev_dbg(&udev->dev, "%s - could not initialize ep %#x\n",
1803 __func__, ep->desc.bEndpointAddress);
1804 return -ENOMEM;
1805 }
1806
1807 if (xhci->quirks & XHCI_MTK_HOST) {
1808 ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
1809 if (ret < 0) {
1810 xhci_free_or_cache_endpoint_ring(xhci,
1811 virt_dev, ep_index);
1812 return ret;
1813 }
1814 }
1815
1816 ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
1817 new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
1818
1819 /* If xhci_endpoint_disable() was called for this endpoint, but the
1820 * xHC hasn't been notified yet through the check_bandwidth() call,
1821 * this re-adds a new state for the endpoint from the new endpoint
1822 * descriptors. We must drop and re-add this endpoint, so we leave the
1823 * drop flags alone.
1824 */
1825 new_drop_flags = le32_to_cpu(ctrl_ctx->drop_flags);
1826
1827 /* Store the usb_device pointer for later use */
1828 ep->hcpriv = udev;
1829
1830 xhci_dbg(xhci, "add ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
1831 (unsigned int) ep->desc.bEndpointAddress,
1832 udev->slot_id,
1833 (unsigned int) new_drop_flags,
1834 (unsigned int) new_add_flags);
1835 return 0;
1836}
1837
1838static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev)
1839{
1840 struct xhci_input_control_ctx *ctrl_ctx;
1841 struct xhci_ep_ctx *ep_ctx;
1842 struct xhci_slot_ctx *slot_ctx;
1843 int i;
1844
1845 ctrl_ctx = xhci_get_input_control_ctx(virt_dev->in_ctx);
1846 if (!ctrl_ctx) {
1847 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
1848 __func__);
1849 return;
1850 }
1851
1852 /* When a device's add flag and drop flag are zero, any subsequent
1853 * configure endpoint command will leave that endpoint's state
1854 * untouched. Make sure we don't leave any old state in the input
1855 * endpoint contexts.
1856 */
1857 ctrl_ctx->drop_flags = 0;
1858 ctrl_ctx->add_flags = 0;
1859 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
1860 slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
1861 /* Endpoint 0 is always valid */
1862 slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1));
1863 for (i = 1; i < 31; ++i) {
1864 ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, i);
1865 ep_ctx->ep_info = 0;
1866 ep_ctx->ep_info2 = 0;
1867 ep_ctx->deq = 0;
1868 ep_ctx->tx_info = 0;
1869 }
1870}
1871
1872static int xhci_configure_endpoint_result(struct xhci_hcd *xhci,
1873 struct usb_device *udev, u32 *cmd_status)
1874{
1875 int ret;
1876
1877 switch (*cmd_status) {
1878 case COMP_CMD_ABORT:
1879 case COMP_CMD_STOP:
1880 xhci_warn(xhci, "Timeout while waiting for configure endpoint command\n");
1881 ret = -ETIME;
1882 break;
1883 case COMP_ENOMEM:
1884 dev_warn(&udev->dev,
1885 "Not enough host controller resources for new device state.\n");
1886 ret = -ENOMEM;
1887 /* FIXME: can we allocate more resources for the HC? */
1888 break;
1889 case COMP_BW_ERR:
1890 case COMP_2ND_BW_ERR:
1891 dev_warn(&udev->dev,
1892 "Not enough bandwidth for new device state.\n");
1893 ret = -ENOSPC;
1894 /* FIXME: can we go back to the old state? */
1895 break;
1896 case COMP_TRB_ERR:
1897 /* the HCD set up something wrong */
1898 dev_warn(&udev->dev, "ERROR: Endpoint drop flag = 0, "
1899 "add flag = 1, "
1900 "and endpoint is not disabled.\n");
1901 ret = -EINVAL;
1902 break;
1903 case COMP_DEV_ERR:
1904 dev_warn(&udev->dev,
1905 "ERROR: Incompatible device for endpoint configure command.\n");
1906 ret = -ENODEV;
1907 break;
1908 case COMP_SUCCESS:
1909 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
1910 "Successful Endpoint Configure command");
1911 ret = 0;
1912 break;
1913 default:
1914 xhci_err(xhci, "ERROR: unexpected command completion code 0x%x.\n",
1915 *cmd_status);
1916 ret = -EINVAL;
1917 break;
1918 }
1919 return ret;
1920}
1921
1922static int xhci_evaluate_context_result(struct xhci_hcd *xhci,
1923 struct usb_device *udev, u32 *cmd_status)
1924{
1925 int ret;
1926 struct xhci_virt_device *virt_dev = xhci->devs[udev->slot_id];
1927
1928 switch (*cmd_status) {
1929 case COMP_CMD_ABORT:
1930 case COMP_CMD_STOP:
1931 xhci_warn(xhci, "Timeout while waiting for evaluate context command\n");
1932 ret = -ETIME;
1933 break;
1934 case COMP_EINVAL:
1935 dev_warn(&udev->dev,
1936 "WARN: xHCI driver setup invalid evaluate context command.\n");
1937 ret = -EINVAL;
1938 break;
1939 case COMP_EBADSLT:
1940 dev_warn(&udev->dev,
1941 "WARN: slot not enabled for evaluate context command.\n");
1942 ret = -EINVAL;
1943 break;
1944 case COMP_CTX_STATE:
1945 dev_warn(&udev->dev,
1946 "WARN: invalid context state for evaluate context command.\n");
1947 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 1);
1948 ret = -EINVAL;
1949 break;
1950 case COMP_DEV_ERR:
1951 dev_warn(&udev->dev,
1952 "ERROR: Incompatible device for evaluate context command.\n");
1953 ret = -ENODEV;
1954 break;
1955 case COMP_MEL_ERR:
1956 /* Max Exit Latency too large error */
1957 dev_warn(&udev->dev, "WARN: Max Exit Latency too large\n");
1958 ret = -EINVAL;
1959 break;
1960 case COMP_SUCCESS:
1961 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
1962 "Successful evaluate context command");
1963 ret = 0;
1964 break;
1965 default:
1966 xhci_err(xhci, "ERROR: unexpected command completion code 0x%x.\n",
1967 *cmd_status);
1968 ret = -EINVAL;
1969 break;
1970 }
1971 return ret;
1972}
1973
1974static u32 xhci_count_num_new_endpoints(struct xhci_hcd *xhci,
1975 struct xhci_input_control_ctx *ctrl_ctx)
1976{
1977 u32 valid_add_flags;
1978 u32 valid_drop_flags;
1979
1980 /* Ignore the slot flag (bit 0), and the default control endpoint flag
1981 * (bit 1). The default control endpoint is added during the Address
1982 * Device command and is never removed until the slot is disabled.
1983 */
1984 valid_add_flags = le32_to_cpu(ctrl_ctx->add_flags) >> 2;
1985 valid_drop_flags = le32_to_cpu(ctrl_ctx->drop_flags) >> 2;
1986
1987 /* Use hweight32 to count the number of ones in the add flags, or
1988 * number of endpoints added. Don't count endpoints that are changed
1989 * (both added and dropped).
1990 */
1991 return hweight32(valid_add_flags) -
1992 hweight32(valid_add_flags & valid_drop_flags);
1993}
1994
1995static unsigned int xhci_count_num_dropped_endpoints(struct xhci_hcd *xhci,
1996 struct xhci_input_control_ctx *ctrl_ctx)
1997{
1998 u32 valid_add_flags;
1999 u32 valid_drop_flags;
2000
2001 valid_add_flags = le32_to_cpu(ctrl_ctx->add_flags) >> 2;
2002 valid_drop_flags = le32_to_cpu(ctrl_ctx->drop_flags) >> 2;
2003
2004 return hweight32(valid_drop_flags) -
2005 hweight32(valid_add_flags & valid_drop_flags);
2006}
2007
2008/*
2009 * We need to reserve the new number of endpoints before the configure endpoint
2010 * command completes. We can't subtract the dropped endpoints from the number
2011 * of active endpoints until the command completes because we can oversubscribe
2012 * the host in this case:
2013 *
2014 * - the first configure endpoint command drops more endpoints than it adds
2015 * - a second configure endpoint command that adds more endpoints is queued
2016 * - the first configure endpoint command fails, so the config is unchanged
2017 * - the second command may succeed, even though there isn't enough resources
2018 *
2019 * Must be called with xhci->lock held.
2020 */
2021static int xhci_reserve_host_resources(struct xhci_hcd *xhci,
2022 struct xhci_input_control_ctx *ctrl_ctx)
2023{
2024 u32 added_eps;
2025
2026 added_eps = xhci_count_num_new_endpoints(xhci, ctrl_ctx);
2027 if (xhci->num_active_eps + added_eps > xhci->limit_active_eps) {
2028 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2029 "Not enough ep ctxs: "
2030 "%u active, need to add %u, limit is %u.",
2031 xhci->num_active_eps, added_eps,
2032 xhci->limit_active_eps);
2033 return -ENOMEM;
2034 }
2035 xhci->num_active_eps += added_eps;
2036 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2037 "Adding %u ep ctxs, %u now active.", added_eps,
2038 xhci->num_active_eps);
2039 return 0;
2040}
2041
2042/*
2043 * The configure endpoint was failed by the xHC for some other reason, so we
2044 * need to revert the resources that failed configuration would have used.
2045 *
2046 * Must be called with xhci->lock held.
2047 */
2048static void xhci_free_host_resources(struct xhci_hcd *xhci,
2049 struct xhci_input_control_ctx *ctrl_ctx)
2050{
2051 u32 num_failed_eps;
2052
2053 num_failed_eps = xhci_count_num_new_endpoints(xhci, ctrl_ctx);
2054 xhci->num_active_eps -= num_failed_eps;
2055 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2056 "Removing %u failed ep ctxs, %u now active.",
2057 num_failed_eps,
2058 xhci->num_active_eps);
2059}
2060
2061/*
2062 * Now that the command has completed, clean up the active endpoint count by
2063 * subtracting out the endpoints that were dropped (but not changed).
2064 *
2065 * Must be called with xhci->lock held.
2066 */
2067static void xhci_finish_resource_reservation(struct xhci_hcd *xhci,
2068 struct xhci_input_control_ctx *ctrl_ctx)
2069{
2070 u32 num_dropped_eps;
2071
2072 num_dropped_eps = xhci_count_num_dropped_endpoints(xhci, ctrl_ctx);
2073 xhci->num_active_eps -= num_dropped_eps;
2074 if (num_dropped_eps)
2075 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2076 "Removing %u dropped ep ctxs, %u now active.",
2077 num_dropped_eps,
2078 xhci->num_active_eps);
2079}
2080
2081static unsigned int xhci_get_block_size(struct usb_device *udev)
2082{
2083 switch (udev->speed) {
2084 case USB_SPEED_LOW:
2085 case USB_SPEED_FULL:
2086 return FS_BLOCK;
2087 case USB_SPEED_HIGH:
2088 return HS_BLOCK;
2089 case USB_SPEED_SUPER:
2090 case USB_SPEED_SUPER_PLUS:
2091 return SS_BLOCK;
2092 case USB_SPEED_UNKNOWN:
2093 case USB_SPEED_WIRELESS:
2094 default:
2095 /* Should never happen */
2096 return 1;
2097 }
2098}
2099
2100static unsigned int
2101xhci_get_largest_overhead(struct xhci_interval_bw *interval_bw)
2102{
2103 if (interval_bw->overhead[LS_OVERHEAD_TYPE])
2104 return LS_OVERHEAD;
2105 if (interval_bw->overhead[FS_OVERHEAD_TYPE])
2106 return FS_OVERHEAD;
2107 return HS_OVERHEAD;
2108}
2109
2110/* If we are changing a LS/FS device under a HS hub,
2111 * make sure (if we are activating a new TT) that the HS bus has enough
2112 * bandwidth for this new TT.
2113 */
2114static int xhci_check_tt_bw_table(struct xhci_hcd *xhci,
2115 struct xhci_virt_device *virt_dev,
2116 int old_active_eps)
2117{
2118 struct xhci_interval_bw_table *bw_table;
2119 struct xhci_tt_bw_info *tt_info;
2120
2121 /* Find the bandwidth table for the root port this TT is attached to. */
2122 bw_table = &xhci->rh_bw[virt_dev->real_port - 1].bw_table;
2123 tt_info = virt_dev->tt_info;
2124 /* If this TT already had active endpoints, the bandwidth for this TT
2125 * has already been added. Removing all periodic endpoints (and thus
2126 * making the TT enactive) will only decrease the bandwidth used.
2127 */
2128 if (old_active_eps)
2129 return 0;
2130 if (old_active_eps == 0 && tt_info->active_eps != 0) {
2131 if (bw_table->bw_used + TT_HS_OVERHEAD > HS_BW_LIMIT)
2132 return -ENOMEM;
2133 return 0;
2134 }
2135 /* Not sure why we would have no new active endpoints...
2136 *
2137 * Maybe because of an Evaluate Context change for a hub update or a
2138 * control endpoint 0 max packet size change?
2139 * FIXME: skip the bandwidth calculation in that case.
2140 */
2141 return 0;
2142}
2143
2144static int xhci_check_ss_bw(struct xhci_hcd *xhci,
2145 struct xhci_virt_device *virt_dev)
2146{
2147 unsigned int bw_reserved;
2148
2149 bw_reserved = DIV_ROUND_UP(SS_BW_RESERVED*SS_BW_LIMIT_IN, 100);
2150 if (virt_dev->bw_table->ss_bw_in > (SS_BW_LIMIT_IN - bw_reserved))
2151 return -ENOMEM;
2152
2153 bw_reserved = DIV_ROUND_UP(SS_BW_RESERVED*SS_BW_LIMIT_OUT, 100);
2154 if (virt_dev->bw_table->ss_bw_out > (SS_BW_LIMIT_OUT - bw_reserved))
2155 return -ENOMEM;
2156
2157 return 0;
2158}
2159
2160/*
2161 * This algorithm is a very conservative estimate of the worst-case scheduling
2162 * scenario for any one interval. The hardware dynamically schedules the
2163 * packets, so we can't tell which microframe could be the limiting factor in
2164 * the bandwidth scheduling. This only takes into account periodic endpoints.
2165 *
2166 * Obviously, we can't solve an NP complete problem to find the minimum worst
2167 * case scenario. Instead, we come up with an estimate that is no less than
2168 * the worst case bandwidth used for any one microframe, but may be an
2169 * over-estimate.
2170 *
2171 * We walk the requirements for each endpoint by interval, starting with the
2172 * smallest interval, and place packets in the schedule where there is only one
2173 * possible way to schedule packets for that interval. In order to simplify
2174 * this algorithm, we record the largest max packet size for each interval, and
2175 * assume all packets will be that size.
2176 *
2177 * For interval 0, we obviously must schedule all packets for each interval.
2178 * The bandwidth for interval 0 is just the amount of data to be transmitted
2179 * (the sum of all max ESIT payload sizes, plus any overhead per packet times
2180 * the number of packets).
2181 *
2182 * For interval 1, we have two possible microframes to schedule those packets
2183 * in. For this algorithm, if we can schedule the same number of packets for
2184 * each possible scheduling opportunity (each microframe), we will do so. The
2185 * remaining number of packets will be saved to be transmitted in the gaps in
2186 * the next interval's scheduling sequence.
2187 *
2188 * As we move those remaining packets to be scheduled with interval 2 packets,
2189 * we have to double the number of remaining packets to transmit. This is
2190 * because the intervals are actually powers of 2, and we would be transmitting
2191 * the previous interval's packets twice in this interval. We also have to be
2192 * sure that when we look at the largest max packet size for this interval, we
2193 * also look at the largest max packet size for the remaining packets and take
2194 * the greater of the two.
2195 *
2196 * The algorithm continues to evenly distribute packets in each scheduling
2197 * opportunity, and push the remaining packets out, until we get to the last
2198 * interval. Then those packets and their associated overhead are just added
2199 * to the bandwidth used.
2200 */
2201static int xhci_check_bw_table(struct xhci_hcd *xhci,
2202 struct xhci_virt_device *virt_dev,
2203 int old_active_eps)
2204{
2205 unsigned int bw_reserved;
2206 unsigned int max_bandwidth;
2207 unsigned int bw_used;
2208 unsigned int block_size;
2209 struct xhci_interval_bw_table *bw_table;
2210 unsigned int packet_size = 0;
2211 unsigned int overhead = 0;
2212 unsigned int packets_transmitted = 0;
2213 unsigned int packets_remaining = 0;
2214 unsigned int i;
2215
2216 if (virt_dev->udev->speed >= USB_SPEED_SUPER)
2217 return xhci_check_ss_bw(xhci, virt_dev);
2218
2219 if (virt_dev->udev->speed == USB_SPEED_HIGH) {
2220 max_bandwidth = HS_BW_LIMIT;
2221 /* Convert percent of bus BW reserved to blocks reserved */
2222 bw_reserved = DIV_ROUND_UP(HS_BW_RESERVED * max_bandwidth, 100);
2223 } else {
2224 max_bandwidth = FS_BW_LIMIT;
2225 bw_reserved = DIV_ROUND_UP(FS_BW_RESERVED * max_bandwidth, 100);
2226 }
2227
2228 bw_table = virt_dev->bw_table;
2229 /* We need to translate the max packet size and max ESIT payloads into
2230 * the units the hardware uses.
2231 */
2232 block_size = xhci_get_block_size(virt_dev->udev);
2233
2234 /* If we are manipulating a LS/FS device under a HS hub, double check
2235 * that the HS bus has enough bandwidth if we are activing a new TT.
2236 */
2237 if (virt_dev->tt_info) {
2238 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2239 "Recalculating BW for rootport %u",
2240 virt_dev->real_port);
2241 if (xhci_check_tt_bw_table(xhci, virt_dev, old_active_eps)) {
2242 xhci_warn(xhci, "Not enough bandwidth on HS bus for "
2243 "newly activated TT.\n");
2244 return -ENOMEM;
2245 }
2246 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2247 "Recalculating BW for TT slot %u port %u",
2248 virt_dev->tt_info->slot_id,
2249 virt_dev->tt_info->ttport);
2250 } else {
2251 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2252 "Recalculating BW for rootport %u",
2253 virt_dev->real_port);
2254 }
2255
2256 /* Add in how much bandwidth will be used for interval zero, or the
2257 * rounded max ESIT payload + number of packets * largest overhead.
2258 */
2259 bw_used = DIV_ROUND_UP(bw_table->interval0_esit_payload, block_size) +
2260 bw_table->interval_bw[0].num_packets *
2261 xhci_get_largest_overhead(&bw_table->interval_bw[0]);
2262
2263 for (i = 1; i < XHCI_MAX_INTERVAL; i++) {
2264 unsigned int bw_added;
2265 unsigned int largest_mps;
2266 unsigned int interval_overhead;
2267
2268 /*
2269 * How many packets could we transmit in this interval?
2270 * If packets didn't fit in the previous interval, we will need
2271 * to transmit that many packets twice within this interval.
2272 */
2273 packets_remaining = 2 * packets_remaining +
2274 bw_table->interval_bw[i].num_packets;
2275
2276 /* Find the largest max packet size of this or the previous
2277 * interval.
2278 */
2279 if (list_empty(&bw_table->interval_bw[i].endpoints))
2280 largest_mps = 0;
2281 else {
2282 struct xhci_virt_ep *virt_ep;
2283 struct list_head *ep_entry;
2284
2285 ep_entry = bw_table->interval_bw[i].endpoints.next;
2286 virt_ep = list_entry(ep_entry,
2287 struct xhci_virt_ep, bw_endpoint_list);
2288 /* Convert to blocks, rounding up */
2289 largest_mps = DIV_ROUND_UP(
2290 virt_ep->bw_info.max_packet_size,
2291 block_size);
2292 }
2293 if (largest_mps > packet_size)
2294 packet_size = largest_mps;
2295
2296 /* Use the larger overhead of this or the previous interval. */
2297 interval_overhead = xhci_get_largest_overhead(
2298 &bw_table->interval_bw[i]);
2299 if (interval_overhead > overhead)
2300 overhead = interval_overhead;
2301
2302 /* How many packets can we evenly distribute across
2303 * (1 << (i + 1)) possible scheduling opportunities?
2304 */
2305 packets_transmitted = packets_remaining >> (i + 1);
2306
2307 /* Add in the bandwidth used for those scheduled packets */
2308 bw_added = packets_transmitted * (overhead + packet_size);
2309
2310 /* How many packets do we have remaining to transmit? */
2311 packets_remaining = packets_remaining % (1 << (i + 1));
2312
2313 /* What largest max packet size should those packets have? */
2314 /* If we've transmitted all packets, don't carry over the
2315 * largest packet size.
2316 */
2317 if (packets_remaining == 0) {
2318 packet_size = 0;
2319 overhead = 0;
2320 } else if (packets_transmitted > 0) {
2321 /* Otherwise if we do have remaining packets, and we've
2322 * scheduled some packets in this interval, take the
2323 * largest max packet size from endpoints with this
2324 * interval.
2325 */
2326 packet_size = largest_mps;
2327 overhead = interval_overhead;
2328 }
2329 /* Otherwise carry over packet_size and overhead from the last
2330 * time we had a remainder.
2331 */
2332 bw_used += bw_added;
2333 if (bw_used > max_bandwidth) {
2334 xhci_warn(xhci, "Not enough bandwidth. "
2335 "Proposed: %u, Max: %u\n",
2336 bw_used, max_bandwidth);
2337 return -ENOMEM;
2338 }
2339 }
2340 /*
2341 * Ok, we know we have some packets left over after even-handedly
2342 * scheduling interval 15. We don't know which microframes they will
2343 * fit into, so we over-schedule and say they will be scheduled every
2344 * microframe.
2345 */
2346 if (packets_remaining > 0)
2347 bw_used += overhead + packet_size;
2348
2349 if (!virt_dev->tt_info && virt_dev->udev->speed == USB_SPEED_HIGH) {
2350 unsigned int port_index = virt_dev->real_port - 1;
2351
2352 /* OK, we're manipulating a HS device attached to a
2353 * root port bandwidth domain. Include the number of active TTs
2354 * in the bandwidth used.
2355 */
2356 bw_used += TT_HS_OVERHEAD *
2357 xhci->rh_bw[port_index].num_active_tts;
2358 }
2359
2360 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2361 "Final bandwidth: %u, Limit: %u, Reserved: %u, "
2362 "Available: %u " "percent",
2363 bw_used, max_bandwidth, bw_reserved,
2364 (max_bandwidth - bw_used - bw_reserved) * 100 /
2365 max_bandwidth);
2366
2367 bw_used += bw_reserved;
2368 if (bw_used > max_bandwidth) {
2369 xhci_warn(xhci, "Not enough bandwidth. Proposed: %u, Max: %u\n",
2370 bw_used, max_bandwidth);
2371 return -ENOMEM;
2372 }
2373
2374 bw_table->bw_used = bw_used;
2375 return 0;
2376}
2377
2378static bool xhci_is_async_ep(unsigned int ep_type)
2379{
2380 return (ep_type != ISOC_OUT_EP && ep_type != INT_OUT_EP &&
2381 ep_type != ISOC_IN_EP &&
2382 ep_type != INT_IN_EP);
2383}
2384
2385static bool xhci_is_sync_in_ep(unsigned int ep_type)
2386{
2387 return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
2388}
2389
2390static unsigned int xhci_get_ss_bw_consumed(struct xhci_bw_info *ep_bw)
2391{
2392 unsigned int mps = DIV_ROUND_UP(ep_bw->max_packet_size, SS_BLOCK);
2393
2394 if (ep_bw->ep_interval == 0)
2395 return SS_OVERHEAD_BURST +
2396 (ep_bw->mult * ep_bw->num_packets *
2397 (SS_OVERHEAD + mps));
2398 return DIV_ROUND_UP(ep_bw->mult * ep_bw->num_packets *
2399 (SS_OVERHEAD + mps + SS_OVERHEAD_BURST),
2400 1 << ep_bw->ep_interval);
2401
2402}
2403
2404void xhci_drop_ep_from_interval_table(struct xhci_hcd *xhci,
2405 struct xhci_bw_info *ep_bw,
2406 struct xhci_interval_bw_table *bw_table,
2407 struct usb_device *udev,
2408 struct xhci_virt_ep *virt_ep,
2409 struct xhci_tt_bw_info *tt_info)
2410{
2411 struct xhci_interval_bw *interval_bw;
2412 int normalized_interval;
2413
2414 if (xhci_is_async_ep(ep_bw->type))
2415 return;
2416
2417 if (udev->speed >= USB_SPEED_SUPER) {
2418 if (xhci_is_sync_in_ep(ep_bw->type))
2419 xhci->devs[udev->slot_id]->bw_table->ss_bw_in -=
2420 xhci_get_ss_bw_consumed(ep_bw);
2421 else
2422 xhci->devs[udev->slot_id]->bw_table->ss_bw_out -=
2423 xhci_get_ss_bw_consumed(ep_bw);
2424 return;
2425 }
2426
2427 /* SuperSpeed endpoints never get added to intervals in the table, so
2428 * this check is only valid for HS/FS/LS devices.
2429 */
2430 if (list_empty(&virt_ep->bw_endpoint_list))
2431 return;
2432 /* For LS/FS devices, we need to translate the interval expressed in
2433 * microframes to frames.
2434 */
2435 if (udev->speed == USB_SPEED_HIGH)
2436 normalized_interval = ep_bw->ep_interval;
2437 else
2438 normalized_interval = ep_bw->ep_interval - 3;
2439
2440 if (normalized_interval == 0)
2441 bw_table->interval0_esit_payload -= ep_bw->max_esit_payload;
2442 interval_bw = &bw_table->interval_bw[normalized_interval];
2443 interval_bw->num_packets -= ep_bw->num_packets;
2444 switch (udev->speed) {
2445 case USB_SPEED_LOW:
2446 interval_bw->overhead[LS_OVERHEAD_TYPE] -= 1;
2447 break;
2448 case USB_SPEED_FULL:
2449 interval_bw->overhead[FS_OVERHEAD_TYPE] -= 1;
2450 break;
2451 case USB_SPEED_HIGH:
2452 interval_bw->overhead[HS_OVERHEAD_TYPE] -= 1;
2453 break;
2454 case USB_SPEED_SUPER:
2455 case USB_SPEED_SUPER_PLUS:
2456 case USB_SPEED_UNKNOWN:
2457 case USB_SPEED_WIRELESS:
2458 /* Should never happen because only LS/FS/HS endpoints will get
2459 * added to the endpoint list.
2460 */
2461 return;
2462 }
2463 if (tt_info)
2464 tt_info->active_eps -= 1;
2465 list_del_init(&virt_ep->bw_endpoint_list);
2466}
2467
2468static void xhci_add_ep_to_interval_table(struct xhci_hcd *xhci,
2469 struct xhci_bw_info *ep_bw,
2470 struct xhci_interval_bw_table *bw_table,
2471 struct usb_device *udev,
2472 struct xhci_virt_ep *virt_ep,
2473 struct xhci_tt_bw_info *tt_info)
2474{
2475 struct xhci_interval_bw *interval_bw;
2476 struct xhci_virt_ep *smaller_ep;
2477 int normalized_interval;
2478
2479 if (xhci_is_async_ep(ep_bw->type))
2480 return;
2481
2482 if (udev->speed == USB_SPEED_SUPER) {
2483 if (xhci_is_sync_in_ep(ep_bw->type))
2484 xhci->devs[udev->slot_id]->bw_table->ss_bw_in +=
2485 xhci_get_ss_bw_consumed(ep_bw);
2486 else
2487 xhci->devs[udev->slot_id]->bw_table->ss_bw_out +=
2488 xhci_get_ss_bw_consumed(ep_bw);
2489 return;
2490 }
2491
2492 /* For LS/FS devices, we need to translate the interval expressed in
2493 * microframes to frames.
2494 */
2495 if (udev->speed == USB_SPEED_HIGH)
2496 normalized_interval = ep_bw->ep_interval;
2497 else
2498 normalized_interval = ep_bw->ep_interval - 3;
2499
2500 if (normalized_interval == 0)
2501 bw_table->interval0_esit_payload += ep_bw->max_esit_payload;
2502 interval_bw = &bw_table->interval_bw[normalized_interval];
2503 interval_bw->num_packets += ep_bw->num_packets;
2504 switch (udev->speed) {
2505 case USB_SPEED_LOW:
2506 interval_bw->overhead[LS_OVERHEAD_TYPE] += 1;
2507 break;
2508 case USB_SPEED_FULL:
2509 interval_bw->overhead[FS_OVERHEAD_TYPE] += 1;
2510 break;
2511 case USB_SPEED_HIGH:
2512 interval_bw->overhead[HS_OVERHEAD_TYPE] += 1;
2513 break;
2514 case USB_SPEED_SUPER:
2515 case USB_SPEED_SUPER_PLUS:
2516 case USB_SPEED_UNKNOWN:
2517 case USB_SPEED_WIRELESS:
2518 /* Should never happen because only LS/FS/HS endpoints will get
2519 * added to the endpoint list.
2520 */
2521 return;
2522 }
2523
2524 if (tt_info)
2525 tt_info->active_eps += 1;
2526 /* Insert the endpoint into the list, largest max packet size first. */
2527 list_for_each_entry(smaller_ep, &interval_bw->endpoints,
2528 bw_endpoint_list) {
2529 if (ep_bw->max_packet_size >=
2530 smaller_ep->bw_info.max_packet_size) {
2531 /* Add the new ep before the smaller endpoint */
2532 list_add_tail(&virt_ep->bw_endpoint_list,
2533 &smaller_ep->bw_endpoint_list);
2534 return;
2535 }
2536 }
2537 /* Add the new endpoint at the end of the list. */
2538 list_add_tail(&virt_ep->bw_endpoint_list,
2539 &interval_bw->endpoints);
2540}
2541
2542void xhci_update_tt_active_eps(struct xhci_hcd *xhci,
2543 struct xhci_virt_device *virt_dev,
2544 int old_active_eps)
2545{
2546 struct xhci_root_port_bw_info *rh_bw_info;
2547 if (!virt_dev->tt_info)
2548 return;
2549
2550 rh_bw_info = &xhci->rh_bw[virt_dev->real_port - 1];
2551 if (old_active_eps == 0 &&
2552 virt_dev->tt_info->active_eps != 0) {
2553 rh_bw_info->num_active_tts += 1;
2554 rh_bw_info->bw_table.bw_used += TT_HS_OVERHEAD;
2555 } else if (old_active_eps != 0 &&
2556 virt_dev->tt_info->active_eps == 0) {
2557 rh_bw_info->num_active_tts -= 1;
2558 rh_bw_info->bw_table.bw_used -= TT_HS_OVERHEAD;
2559 }
2560}
2561
2562static int xhci_reserve_bandwidth(struct xhci_hcd *xhci,
2563 struct xhci_virt_device *virt_dev,
2564 struct xhci_container_ctx *in_ctx)
2565{
2566 struct xhci_bw_info ep_bw_info[31];
2567 int i;
2568 struct xhci_input_control_ctx *ctrl_ctx;
2569 int old_active_eps = 0;
2570
2571 if (virt_dev->tt_info)
2572 old_active_eps = virt_dev->tt_info->active_eps;
2573
2574 ctrl_ctx = xhci_get_input_control_ctx(in_ctx);
2575 if (!ctrl_ctx) {
2576 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
2577 __func__);
2578 return -ENOMEM;
2579 }
2580
2581 for (i = 0; i < 31; i++) {
2582 if (!EP_IS_ADDED(ctrl_ctx, i) && !EP_IS_DROPPED(ctrl_ctx, i))
2583 continue;
2584
2585 /* Make a copy of the BW info in case we need to revert this */
2586 memcpy(&ep_bw_info[i], &virt_dev->eps[i].bw_info,
2587 sizeof(ep_bw_info[i]));
2588 /* Drop the endpoint from the interval table if the endpoint is
2589 * being dropped or changed.
2590 */
2591 if (EP_IS_DROPPED(ctrl_ctx, i))
2592 xhci_drop_ep_from_interval_table(xhci,
2593 &virt_dev->eps[i].bw_info,
2594 virt_dev->bw_table,
2595 virt_dev->udev,
2596 &virt_dev->eps[i],
2597 virt_dev->tt_info);
2598 }
2599 /* Overwrite the information stored in the endpoints' bw_info */
2600 xhci_update_bw_info(xhci, virt_dev->in_ctx, ctrl_ctx, virt_dev);
2601 for (i = 0; i < 31; i++) {
2602 /* Add any changed or added endpoints to the interval table */
2603 if (EP_IS_ADDED(ctrl_ctx, i))
2604 xhci_add_ep_to_interval_table(xhci,
2605 &virt_dev->eps[i].bw_info,
2606 virt_dev->bw_table,
2607 virt_dev->udev,
2608 &virt_dev->eps[i],
2609 virt_dev->tt_info);
2610 }
2611
2612 if (!xhci_check_bw_table(xhci, virt_dev, old_active_eps)) {
2613 /* Ok, this fits in the bandwidth we have.
2614 * Update the number of active TTs.
2615 */
2616 xhci_update_tt_active_eps(xhci, virt_dev, old_active_eps);
2617 return 0;
2618 }
2619
2620 /* We don't have enough bandwidth for this, revert the stored info. */
2621 for (i = 0; i < 31; i++) {
2622 if (!EP_IS_ADDED(ctrl_ctx, i) && !EP_IS_DROPPED(ctrl_ctx, i))
2623 continue;
2624
2625 /* Drop the new copies of any added or changed endpoints from
2626 * the interval table.
2627 */
2628 if (EP_IS_ADDED(ctrl_ctx, i)) {
2629 xhci_drop_ep_from_interval_table(xhci,
2630 &virt_dev->eps[i].bw_info,
2631 virt_dev->bw_table,
2632 virt_dev->udev,
2633 &virt_dev->eps[i],
2634 virt_dev->tt_info);
2635 }
2636 /* Revert the endpoint back to its old information */
2637 memcpy(&virt_dev->eps[i].bw_info, &ep_bw_info[i],
2638 sizeof(ep_bw_info[i]));
2639 /* Add any changed or dropped endpoints back into the table */
2640 if (EP_IS_DROPPED(ctrl_ctx, i))
2641 xhci_add_ep_to_interval_table(xhci,
2642 &virt_dev->eps[i].bw_info,
2643 virt_dev->bw_table,
2644 virt_dev->udev,
2645 &virt_dev->eps[i],
2646 virt_dev->tt_info);
2647 }
2648 return -ENOMEM;
2649}
2650
2651
2652/* Issue a configure endpoint command or evaluate context command
2653 * and wait for it to finish.
2654 */
2655static int xhci_configure_endpoint(struct xhci_hcd *xhci,
2656 struct usb_device *udev,
2657 struct xhci_command *command,
2658 bool ctx_change, bool must_succeed)
2659{
2660 int ret;
2661 unsigned long flags;
2662 struct xhci_input_control_ctx *ctrl_ctx;
2663 struct xhci_virt_device *virt_dev;
2664
2665 if (!command)
2666 return -EINVAL;
2667
2668 spin_lock_irqsave(&xhci->lock, flags);
2669 virt_dev = xhci->devs[udev->slot_id];
2670
2671 ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
2672 if (!ctrl_ctx) {
2673 spin_unlock_irqrestore(&xhci->lock, flags);
2674 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
2675 __func__);
2676 return -ENOMEM;
2677 }
2678
2679 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK) &&
2680 xhci_reserve_host_resources(xhci, ctrl_ctx)) {
2681 spin_unlock_irqrestore(&xhci->lock, flags);
2682 xhci_warn(xhci, "Not enough host resources, "
2683 "active endpoint contexts = %u\n",
2684 xhci->num_active_eps);
2685 return -ENOMEM;
2686 }
2687 if ((xhci->quirks & XHCI_SW_BW_CHECKING) &&
2688 xhci_reserve_bandwidth(xhci, virt_dev, command->in_ctx)) {
2689 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK))
2690 xhci_free_host_resources(xhci, ctrl_ctx);
2691 spin_unlock_irqrestore(&xhci->lock, flags);
2692 xhci_warn(xhci, "Not enough bandwidth\n");
2693 return -ENOMEM;
2694 }
2695
2696 if (!ctx_change)
2697 ret = xhci_queue_configure_endpoint(xhci, command,
2698 command->in_ctx->dma,
2699 udev->slot_id, must_succeed);
2700 else
2701 ret = xhci_queue_evaluate_context(xhci, command,
2702 command->in_ctx->dma,
2703 udev->slot_id, must_succeed);
2704 if (ret < 0) {
2705 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK))
2706 xhci_free_host_resources(xhci, ctrl_ctx);
2707 spin_unlock_irqrestore(&xhci->lock, flags);
2708 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
2709 "FIXME allocate a new ring segment");
2710 return -ENOMEM;
2711 }
2712 xhci_ring_cmd_db(xhci);
2713 spin_unlock_irqrestore(&xhci->lock, flags);
2714
2715 /* Wait for the configure endpoint command to complete */
2716 wait_for_completion(command->completion);
2717
2718 if (!ctx_change)
2719 ret = xhci_configure_endpoint_result(xhci, udev,
2720 &command->status);
2721 else
2722 ret = xhci_evaluate_context_result(xhci, udev,
2723 &command->status);
2724
2725 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) {
2726 spin_lock_irqsave(&xhci->lock, flags);
2727 /* If the command failed, remove the reserved resources.
2728 * Otherwise, clean up the estimate to include dropped eps.
2729 */
2730 if (ret)
2731 xhci_free_host_resources(xhci, ctrl_ctx);
2732 else
2733 xhci_finish_resource_reservation(xhci, ctrl_ctx);
2734 spin_unlock_irqrestore(&xhci->lock, flags);
2735 }
2736 return ret;
2737}
2738
2739static void xhci_check_bw_drop_ep_streams(struct xhci_hcd *xhci,
2740 struct xhci_virt_device *vdev, int i)
2741{
2742 struct xhci_virt_ep *ep = &vdev->eps[i];
2743
2744 if (ep->ep_state & EP_HAS_STREAMS) {
2745 xhci_warn(xhci, "WARN: endpoint 0x%02x has streams on set_interface, freeing streams.\n",
2746 xhci_get_endpoint_address(i));
2747 xhci_free_stream_info(xhci, ep->stream_info);
2748 ep->stream_info = NULL;
2749 ep->ep_state &= ~EP_HAS_STREAMS;
2750 }
2751}
2752
2753/* Called after one or more calls to xhci_add_endpoint() or
2754 * xhci_drop_endpoint(). If this call fails, the USB core is expected
2755 * to call xhci_reset_bandwidth().
2756 *
2757 * Since we are in the middle of changing either configuration or
2758 * installing a new alt setting, the USB core won't allow URBs to be
2759 * enqueued for any endpoint on the old config or interface. Nothing
2760 * else should be touching the xhci->devs[slot_id] structure, so we
2761 * don't need to take the xhci->lock for manipulating that.
2762 */
2763int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
2764{
2765 int i;
2766 int ret = 0;
2767 struct xhci_hcd *xhci;
2768 struct xhci_virt_device *virt_dev;
2769 struct xhci_input_control_ctx *ctrl_ctx;
2770 struct xhci_slot_ctx *slot_ctx;
2771 struct xhci_command *command;
2772
2773 ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
2774 if (ret <= 0)
2775 return ret;
2776 xhci = hcd_to_xhci(hcd);
2777 if ((xhci->xhc_state & XHCI_STATE_DYING) ||
2778 (xhci->xhc_state & XHCI_STATE_REMOVING))
2779 return -ENODEV;
2780
2781 xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev);
2782 virt_dev = xhci->devs[udev->slot_id];
2783
2784 command = xhci_alloc_command(xhci, false, true, GFP_KERNEL);
2785 if (!command)
2786 return -ENOMEM;
2787
2788 command->in_ctx = virt_dev->in_ctx;
2789
2790 /* See section 4.6.6 - A0 = 1; A1 = D0 = D1 = 0 */
2791 ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
2792 if (!ctrl_ctx) {
2793 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
2794 __func__);
2795 ret = -ENOMEM;
2796 goto command_cleanup;
2797 }
2798 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
2799 ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG);
2800 ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG));
2801
2802 /* Don't issue the command if there's no endpoints to update. */
2803 if (ctrl_ctx->add_flags == cpu_to_le32(SLOT_FLAG) &&
2804 ctrl_ctx->drop_flags == 0) {
2805 ret = 0;
2806 goto command_cleanup;
2807 }
2808 /* Fix up Context Entries field. Minimum value is EP0 == BIT(1). */
2809 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
2810 for (i = 31; i >= 1; i--) {
2811 __le32 le32 = cpu_to_le32(BIT(i));
2812
2813 if ((virt_dev->eps[i-1].ring && !(ctrl_ctx->drop_flags & le32))
2814 || (ctrl_ctx->add_flags & le32) || i == 1) {
2815 slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
2816 slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(i));
2817 break;
2818 }
2819 }
2820 xhci_dbg(xhci, "New Input Control Context:\n");
2821 xhci_dbg_ctx(xhci, virt_dev->in_ctx,
2822 LAST_CTX_TO_EP_NUM(le32_to_cpu(slot_ctx->dev_info)));
2823
2824 ret = xhci_configure_endpoint(xhci, udev, command,
2825 false, false);
2826 if (ret)
2827 /* Callee should call reset_bandwidth() */
2828 goto command_cleanup;
2829
2830 xhci_dbg(xhci, "Output context after successful config ep cmd:\n");
2831 xhci_dbg_ctx(xhci, virt_dev->out_ctx,
2832 LAST_CTX_TO_EP_NUM(le32_to_cpu(slot_ctx->dev_info)));
2833
2834 /* Free any rings that were dropped, but not changed. */
2835 for (i = 1; i < 31; ++i) {
2836 if ((le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1))) &&
2837 !(le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1)))) {
2838 xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i);
2839 xhci_check_bw_drop_ep_streams(xhci, virt_dev, i);
2840 }
2841 }
2842 xhci_zero_in_ctx(xhci, virt_dev);
2843 /*
2844 * Install any rings for completely new endpoints or changed endpoints,
2845 * and free or cache any old rings from changed endpoints.
2846 */
2847 for (i = 1; i < 31; ++i) {
2848 if (!virt_dev->eps[i].new_ring)
2849 continue;
2850 /* Only cache or free the old ring if it exists.
2851 * It may not if this is the first add of an endpoint.
2852 */
2853 if (virt_dev->eps[i].ring) {
2854 xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i);
2855 }
2856 xhci_check_bw_drop_ep_streams(xhci, virt_dev, i);
2857 virt_dev->eps[i].ring = virt_dev->eps[i].new_ring;
2858 virt_dev->eps[i].new_ring = NULL;
2859 }
2860command_cleanup:
2861 kfree(command->completion);
2862 kfree(command);
2863
2864 return ret;
2865}
2866
2867void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
2868{
2869 struct xhci_hcd *xhci;
2870 struct xhci_virt_device *virt_dev;
2871 int i, ret;
2872
2873 ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
2874 if (ret <= 0)
2875 return;
2876 xhci = hcd_to_xhci(hcd);
2877
2878 xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev);
2879 virt_dev = xhci->devs[udev->slot_id];
2880 /* Free any rings allocated for added endpoints */
2881 for (i = 0; i < 31; ++i) {
2882 if (virt_dev->eps[i].new_ring) {
2883 xhci_ring_free(xhci, virt_dev->eps[i].new_ring);
2884 virt_dev->eps[i].new_ring = NULL;
2885 }
2886 }
2887 xhci_zero_in_ctx(xhci, virt_dev);
2888}
2889
2890static void xhci_setup_input_ctx_for_config_ep(struct xhci_hcd *xhci,
2891 struct xhci_container_ctx *in_ctx,
2892 struct xhci_container_ctx *out_ctx,
2893 struct xhci_input_control_ctx *ctrl_ctx,
2894 u32 add_flags, u32 drop_flags)
2895{
2896 ctrl_ctx->add_flags = cpu_to_le32(add_flags);
2897 ctrl_ctx->drop_flags = cpu_to_le32(drop_flags);
2898 xhci_slot_copy(xhci, in_ctx, out_ctx);
2899 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
2900
2901 xhci_dbg(xhci, "Input Context:\n");
2902 xhci_dbg_ctx(xhci, in_ctx, xhci_last_valid_endpoint(add_flags));
2903}
2904
2905static void xhci_setup_input_ctx_for_quirk(struct xhci_hcd *xhci,
2906 unsigned int slot_id, unsigned int ep_index,
2907 struct xhci_dequeue_state *deq_state)
2908{
2909 struct xhci_input_control_ctx *ctrl_ctx;
2910 struct xhci_container_ctx *in_ctx;
2911 struct xhci_ep_ctx *ep_ctx;
2912 u32 added_ctxs;
2913 dma_addr_t addr;
2914
2915 in_ctx = xhci->devs[slot_id]->in_ctx;
2916 ctrl_ctx = xhci_get_input_control_ctx(in_ctx);
2917 if (!ctrl_ctx) {
2918 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
2919 __func__);
2920 return;
2921 }
2922
2923 xhci_endpoint_copy(xhci, xhci->devs[slot_id]->in_ctx,
2924 xhci->devs[slot_id]->out_ctx, ep_index);
2925 ep_ctx = xhci_get_ep_ctx(xhci, in_ctx, ep_index);
2926 addr = xhci_trb_virt_to_dma(deq_state->new_deq_seg,
2927 deq_state->new_deq_ptr);
2928 if (addr == 0) {
2929 xhci_warn(xhci, "WARN Cannot submit config ep after "
2930 "reset ep command\n");
2931 xhci_warn(xhci, "WARN deq seg = %p, deq ptr = %p\n",
2932 deq_state->new_deq_seg,
2933 deq_state->new_deq_ptr);
2934 return;
2935 }
2936 ep_ctx->deq = cpu_to_le64(addr | deq_state->new_cycle_state);
2937
2938 added_ctxs = xhci_get_endpoint_flag_from_index(ep_index);
2939 xhci_setup_input_ctx_for_config_ep(xhci, xhci->devs[slot_id]->in_ctx,
2940 xhci->devs[slot_id]->out_ctx, ctrl_ctx,
2941 added_ctxs, added_ctxs);
2942}
2943
2944void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci,
2945 unsigned int ep_index, struct xhci_td *td)
2946{
2947 struct xhci_dequeue_state deq_state;
2948 struct xhci_virt_ep *ep;
2949 struct usb_device *udev = td->urb->dev;
2950
2951 xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
2952 "Cleaning up stalled endpoint ring");
2953 ep = &xhci->devs[udev->slot_id]->eps[ep_index];
2954 /* We need to move the HW's dequeue pointer past this TD,
2955 * or it will attempt to resend it on the next doorbell ring.
2956 */
2957 xhci_find_new_dequeue_state(xhci, udev->slot_id,
2958 ep_index, ep->stopped_stream, td, &deq_state);
2959
2960 if (!deq_state.new_deq_ptr || !deq_state.new_deq_seg)
2961 return;
2962
2963 /* HW with the reset endpoint quirk will use the saved dequeue state to
2964 * issue a configure endpoint command later.
2965 */
2966 if (!(xhci->quirks & XHCI_RESET_EP_QUIRK)) {
2967 xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
2968 "Queueing new dequeue state");
2969 xhci_queue_new_dequeue_state(xhci, udev->slot_id,
2970 ep_index, ep->stopped_stream, &deq_state);
2971 } else {
2972 /* Better hope no one uses the input context between now and the
2973 * reset endpoint completion!
2974 * XXX: No idea how this hardware will react when stream rings
2975 * are enabled.
2976 */
2977 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
2978 "Setting up input context for "
2979 "configure endpoint command");
2980 xhci_setup_input_ctx_for_quirk(xhci, udev->slot_id,
2981 ep_index, &deq_state);
2982 }
2983}
2984
2985/* Called when clearing halted device. The core should have sent the control
2986 * message to clear the device halt condition. The host side of the halt should
2987 * already be cleared with a reset endpoint command issued when the STALL tx
2988 * event was received.
2989 *
2990 * Context: in_interrupt
2991 */
2992
2993void xhci_endpoint_reset(struct usb_hcd *hcd,
2994 struct usb_host_endpoint *ep)
2995{
2996 struct xhci_hcd *xhci;
2997
2998 xhci = hcd_to_xhci(hcd);
2999
3000 /*
3001 * We might need to implement the config ep cmd in xhci 4.8.1 note:
3002 * The Reset Endpoint Command may only be issued to endpoints in the
3003 * Halted state. If software wishes reset the Data Toggle or Sequence
3004 * Number of an endpoint that isn't in the Halted state, then software
3005 * may issue a Configure Endpoint Command with the Drop and Add bits set
3006 * for the target endpoint. that is in the Stopped state.
3007 */
3008
3009 /* For now just print debug to follow the situation */
3010 xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n",
3011 ep->desc.bEndpointAddress);
3012}
3013
3014static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,
3015 struct usb_device *udev, struct usb_host_endpoint *ep,
3016 unsigned int slot_id)
3017{
3018 int ret;
3019 unsigned int ep_index;
3020 unsigned int ep_state;
3021
3022 if (!ep)
3023 return -EINVAL;
3024 ret = xhci_check_args(xhci_to_hcd(xhci), udev, ep, 1, true, __func__);
3025 if (ret <= 0)
3026 return -EINVAL;
3027 if (usb_ss_max_streams(&ep->ss_ep_comp) == 0) {
3028 xhci_warn(xhci, "WARN: SuperSpeed Endpoint Companion"
3029 " descriptor for ep 0x%x does not support streams\n",
3030 ep->desc.bEndpointAddress);
3031 return -EINVAL;
3032 }
3033
3034 ep_index = xhci_get_endpoint_index(&ep->desc);
3035 ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
3036 if (ep_state & EP_HAS_STREAMS ||
3037 ep_state & EP_GETTING_STREAMS) {
3038 xhci_warn(xhci, "WARN: SuperSpeed bulk endpoint 0x%x "
3039 "already has streams set up.\n",
3040 ep->desc.bEndpointAddress);
3041 xhci_warn(xhci, "Send email to xHCI maintainer and ask for "
3042 "dynamic stream context array reallocation.\n");
3043 return -EINVAL;
3044 }
3045 if (!list_empty(&xhci->devs[slot_id]->eps[ep_index].ring->td_list)) {
3046 xhci_warn(xhci, "Cannot setup streams for SuperSpeed bulk "
3047 "endpoint 0x%x; URBs are pending.\n",
3048 ep->desc.bEndpointAddress);
3049 return -EINVAL;
3050 }
3051 return 0;
3052}
3053
3054static void xhci_calculate_streams_entries(struct xhci_hcd *xhci,
3055 unsigned int *num_streams, unsigned int *num_stream_ctxs)
3056{
3057 unsigned int max_streams;
3058
3059 /* The stream context array size must be a power of two */
3060 *num_stream_ctxs = roundup_pow_of_two(*num_streams);
3061 /*
3062 * Find out how many primary stream array entries the host controller
3063 * supports. Later we may use secondary stream arrays (similar to 2nd
3064 * level page entries), but that's an optional feature for xHCI host
3065 * controllers. xHCs must support at least 4 stream IDs.
3066 */
3067 max_streams = HCC_MAX_PSA(xhci->hcc_params);
3068 if (*num_stream_ctxs > max_streams) {
3069 xhci_dbg(xhci, "xHCI HW only supports %u stream ctx entries.\n",
3070 max_streams);
3071 *num_stream_ctxs = max_streams;
3072 *num_streams = max_streams;
3073 }
3074}
3075
3076/* Returns an error code if one of the endpoint already has streams.
3077 * This does not change any data structures, it only checks and gathers
3078 * information.
3079 */
3080static int xhci_calculate_streams_and_bitmask(struct xhci_hcd *xhci,
3081 struct usb_device *udev,
3082 struct usb_host_endpoint **eps, unsigned int num_eps,
3083 unsigned int *num_streams, u32 *changed_ep_bitmask)
3084{
3085 unsigned int max_streams;
3086 unsigned int endpoint_flag;
3087 int i;
3088 int ret;
3089
3090 for (i = 0; i < num_eps; i++) {
3091 ret = xhci_check_streams_endpoint(xhci, udev,
3092 eps[i], udev->slot_id);
3093 if (ret < 0)
3094 return ret;
3095
3096 max_streams = usb_ss_max_streams(&eps[i]->ss_ep_comp);
3097 if (max_streams < (*num_streams - 1)) {
3098 xhci_dbg(xhci, "Ep 0x%x only supports %u stream IDs.\n",
3099 eps[i]->desc.bEndpointAddress,
3100 max_streams);
3101 *num_streams = max_streams+1;
3102 }
3103
3104 endpoint_flag = xhci_get_endpoint_flag(&eps[i]->desc);
3105 if (*changed_ep_bitmask & endpoint_flag)
3106 return -EINVAL;
3107 *changed_ep_bitmask |= endpoint_flag;
3108 }
3109 return 0;
3110}
3111
3112static u32 xhci_calculate_no_streams_bitmask(struct xhci_hcd *xhci,
3113 struct usb_device *udev,
3114 struct usb_host_endpoint **eps, unsigned int num_eps)
3115{
3116 u32 changed_ep_bitmask = 0;
3117 unsigned int slot_id;
3118 unsigned int ep_index;
3119 unsigned int ep_state;
3120 int i;
3121
3122 slot_id = udev->slot_id;
3123 if (!xhci->devs[slot_id])
3124 return 0;
3125
3126 for (i = 0; i < num_eps; i++) {
3127 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3128 ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
3129 /* Are streams already being freed for the endpoint? */
3130 if (ep_state & EP_GETTING_NO_STREAMS) {
3131 xhci_warn(xhci, "WARN Can't disable streams for "
3132 "endpoint 0x%x, "
3133 "streams are being disabled already\n",
3134 eps[i]->desc.bEndpointAddress);
3135 return 0;
3136 }
3137 /* Are there actually any streams to free? */
3138 if (!(ep_state & EP_HAS_STREAMS) &&
3139 !(ep_state & EP_GETTING_STREAMS)) {
3140 xhci_warn(xhci, "WARN Can't disable streams for "
3141 "endpoint 0x%x, "
3142 "streams are already disabled!\n",
3143 eps[i]->desc.bEndpointAddress);
3144 xhci_warn(xhci, "WARN xhci_free_streams() called "
3145 "with non-streams endpoint\n");
3146 return 0;
3147 }
3148 changed_ep_bitmask |= xhci_get_endpoint_flag(&eps[i]->desc);
3149 }
3150 return changed_ep_bitmask;
3151}
3152
3153/*
3154 * The USB device drivers use this function (through the HCD interface in USB
3155 * core) to prepare a set of bulk endpoints to use streams. Streams are used to
3156 * coordinate mass storage command queueing across multiple endpoints (basically
3157 * a stream ID == a task ID).
3158 *
3159 * Setting up streams involves allocating the same size stream context array
3160 * for each endpoint and issuing a configure endpoint command for all endpoints.
3161 *
3162 * Don't allow the call to succeed if one endpoint only supports one stream
3163 * (which means it doesn't support streams at all).
3164 *
3165 * Drivers may get less stream IDs than they asked for, if the host controller
3166 * hardware or endpoints claim they can't support the number of requested
3167 * stream IDs.
3168 */
3169int xhci_alloc_streams(struct usb_hcd *hcd, struct usb_device *udev,
3170 struct usb_host_endpoint **eps, unsigned int num_eps,
3171 unsigned int num_streams, gfp_t mem_flags)
3172{
3173 int i, ret;
3174 struct xhci_hcd *xhci;
3175 struct xhci_virt_device *vdev;
3176 struct xhci_command *config_cmd;
3177 struct xhci_input_control_ctx *ctrl_ctx;
3178 unsigned int ep_index;
3179 unsigned int num_stream_ctxs;
3180 unsigned long flags;
3181 u32 changed_ep_bitmask = 0;
3182
3183 if (!eps)
3184 return -EINVAL;
3185
3186 /* Add one to the number of streams requested to account for
3187 * stream 0 that is reserved for xHCI usage.
3188 */
3189 num_streams += 1;
3190 xhci = hcd_to_xhci(hcd);
3191 xhci_dbg(xhci, "Driver wants %u stream IDs (including stream 0).\n",
3192 num_streams);
3193
3194 /* MaxPSASize value 0 (2 streams) means streams are not supported */
3195 if ((xhci->quirks & XHCI_BROKEN_STREAMS) ||
3196 HCC_MAX_PSA(xhci->hcc_params) < 4) {
3197 xhci_dbg(xhci, "xHCI controller does not support streams.\n");
3198 return -ENOSYS;
3199 }
3200
3201 config_cmd = xhci_alloc_command(xhci, true, true, mem_flags);
3202 if (!config_cmd) {
3203 xhci_dbg(xhci, "Could not allocate xHCI command structure.\n");
3204 return -ENOMEM;
3205 }
3206 ctrl_ctx = xhci_get_input_control_ctx(config_cmd->in_ctx);
3207 if (!ctrl_ctx) {
3208 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
3209 __func__);
3210 xhci_free_command(xhci, config_cmd);
3211 return -ENOMEM;
3212 }
3213
3214 /* Check to make sure all endpoints are not already configured for
3215 * streams. While we're at it, find the maximum number of streams that
3216 * all the endpoints will support and check for duplicate endpoints.
3217 */
3218 spin_lock_irqsave(&xhci->lock, flags);
3219 ret = xhci_calculate_streams_and_bitmask(xhci, udev, eps,
3220 num_eps, &num_streams, &changed_ep_bitmask);
3221 if (ret < 0) {
3222 xhci_free_command(xhci, config_cmd);
3223 spin_unlock_irqrestore(&xhci->lock, flags);
3224 return ret;
3225 }
3226 if (num_streams <= 1) {
3227 xhci_warn(xhci, "WARN: endpoints can't handle "
3228 "more than one stream.\n");
3229 xhci_free_command(xhci, config_cmd);
3230 spin_unlock_irqrestore(&xhci->lock, flags);
3231 return -EINVAL;
3232 }
3233 vdev = xhci->devs[udev->slot_id];
3234 /* Mark each endpoint as being in transition, so
3235 * xhci_urb_enqueue() will reject all URBs.
3236 */
3237 for (i = 0; i < num_eps; i++) {
3238 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3239 vdev->eps[ep_index].ep_state |= EP_GETTING_STREAMS;
3240 }
3241 spin_unlock_irqrestore(&xhci->lock, flags);
3242
3243 /* Setup internal data structures and allocate HW data structures for
3244 * streams (but don't install the HW structures in the input context
3245 * until we're sure all memory allocation succeeded).
3246 */
3247 xhci_calculate_streams_entries(xhci, &num_streams, &num_stream_ctxs);
3248 xhci_dbg(xhci, "Need %u stream ctx entries for %u stream IDs.\n",
3249 num_stream_ctxs, num_streams);
3250
3251 for (i = 0; i < num_eps; i++) {
3252 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3253 vdev->eps[ep_index].stream_info = xhci_alloc_stream_info(xhci,
3254 num_stream_ctxs,
3255 num_streams, mem_flags);
3256 if (!vdev->eps[ep_index].stream_info)
3257 goto cleanup;
3258 /* Set maxPstreams in endpoint context and update deq ptr to
3259 * point to stream context array. FIXME
3260 */
3261 }
3262
3263 /* Set up the input context for a configure endpoint command. */
3264 for (i = 0; i < num_eps; i++) {
3265 struct xhci_ep_ctx *ep_ctx;
3266
3267 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3268 ep_ctx = xhci_get_ep_ctx(xhci, config_cmd->in_ctx, ep_index);
3269
3270 xhci_endpoint_copy(xhci, config_cmd->in_ctx,
3271 vdev->out_ctx, ep_index);
3272 xhci_setup_streams_ep_input_ctx(xhci, ep_ctx,
3273 vdev->eps[ep_index].stream_info);
3274 }
3275 /* Tell the HW to drop its old copy of the endpoint context info
3276 * and add the updated copy from the input context.
3277 */
3278 xhci_setup_input_ctx_for_config_ep(xhci, config_cmd->in_ctx,
3279 vdev->out_ctx, ctrl_ctx,
3280 changed_ep_bitmask, changed_ep_bitmask);
3281
3282 /* Issue and wait for the configure endpoint command */
3283 ret = xhci_configure_endpoint(xhci, udev, config_cmd,
3284 false, false);
3285
3286 /* xHC rejected the configure endpoint command for some reason, so we
3287 * leave the old ring intact and free our internal streams data
3288 * structure.
3289 */
3290 if (ret < 0)
3291 goto cleanup;
3292
3293 spin_lock_irqsave(&xhci->lock, flags);
3294 for (i = 0; i < num_eps; i++) {
3295 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3296 vdev->eps[ep_index].ep_state &= ~EP_GETTING_STREAMS;
3297 xhci_dbg(xhci, "Slot %u ep ctx %u now has streams.\n",
3298 udev->slot_id, ep_index);
3299 vdev->eps[ep_index].ep_state |= EP_HAS_STREAMS;
3300 }
3301 xhci_free_command(xhci, config_cmd);
3302 spin_unlock_irqrestore(&xhci->lock, flags);
3303
3304 /* Subtract 1 for stream 0, which drivers can't use */
3305 return num_streams - 1;
3306
3307cleanup:
3308 /* If it didn't work, free the streams! */
3309 for (i = 0; i < num_eps; i++) {
3310 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3311 xhci_free_stream_info(xhci, vdev->eps[ep_index].stream_info);
3312 vdev->eps[ep_index].stream_info = NULL;
3313 /* FIXME Unset maxPstreams in endpoint context and
3314 * update deq ptr to point to normal string ring.
3315 */
3316 vdev->eps[ep_index].ep_state &= ~EP_GETTING_STREAMS;
3317 vdev->eps[ep_index].ep_state &= ~EP_HAS_STREAMS;
3318 xhci_endpoint_zero(xhci, vdev, eps[i]);
3319 }
3320 xhci_free_command(xhci, config_cmd);
3321 return -ENOMEM;
3322}
3323
3324/* Transition the endpoint from using streams to being a "normal" endpoint
3325 * without streams.
3326 *
3327 * Modify the endpoint context state, submit a configure endpoint command,
3328 * and free all endpoint rings for streams if that completes successfully.
3329 */
3330int xhci_free_streams(struct usb_hcd *hcd, struct usb_device *udev,
3331 struct usb_host_endpoint **eps, unsigned int num_eps,
3332 gfp_t mem_flags)
3333{
3334 int i, ret;
3335 struct xhci_hcd *xhci;
3336 struct xhci_virt_device *vdev;
3337 struct xhci_command *command;
3338 struct xhci_input_control_ctx *ctrl_ctx;
3339 unsigned int ep_index;
3340 unsigned long flags;
3341 u32 changed_ep_bitmask;
3342
3343 xhci = hcd_to_xhci(hcd);
3344 vdev = xhci->devs[udev->slot_id];
3345
3346 /* Set up a configure endpoint command to remove the streams rings */
3347 spin_lock_irqsave(&xhci->lock, flags);
3348 changed_ep_bitmask = xhci_calculate_no_streams_bitmask(xhci,
3349 udev, eps, num_eps);
3350 if (changed_ep_bitmask == 0) {
3351 spin_unlock_irqrestore(&xhci->lock, flags);
3352 return -EINVAL;
3353 }
3354
3355 /* Use the xhci_command structure from the first endpoint. We may have
3356 * allocated too many, but the driver may call xhci_free_streams() for
3357 * each endpoint it grouped into one call to xhci_alloc_streams().
3358 */
3359 ep_index = xhci_get_endpoint_index(&eps[0]->desc);
3360 command = vdev->eps[ep_index].stream_info->free_streams_command;
3361 ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
3362 if (!ctrl_ctx) {
3363 spin_unlock_irqrestore(&xhci->lock, flags);
3364 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
3365 __func__);
3366 return -EINVAL;
3367 }
3368
3369 for (i = 0; i < num_eps; i++) {
3370 struct xhci_ep_ctx *ep_ctx;
3371
3372 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3373 ep_ctx = xhci_get_ep_ctx(xhci, command->in_ctx, ep_index);
3374 xhci->devs[udev->slot_id]->eps[ep_index].ep_state |=
3375 EP_GETTING_NO_STREAMS;
3376
3377 xhci_endpoint_copy(xhci, command->in_ctx,
3378 vdev->out_ctx, ep_index);
3379 xhci_setup_no_streams_ep_input_ctx(ep_ctx,
3380 &vdev->eps[ep_index]);
3381 }
3382 xhci_setup_input_ctx_for_config_ep(xhci, command->in_ctx,
3383 vdev->out_ctx, ctrl_ctx,
3384 changed_ep_bitmask, changed_ep_bitmask);
3385 spin_unlock_irqrestore(&xhci->lock, flags);
3386
3387 /* Issue and wait for the configure endpoint command,
3388 * which must succeed.
3389 */
3390 ret = xhci_configure_endpoint(xhci, udev, command,
3391 false, true);
3392
3393 /* xHC rejected the configure endpoint command for some reason, so we
3394 * leave the streams rings intact.
3395 */
3396 if (ret < 0)
3397 return ret;
3398
3399 spin_lock_irqsave(&xhci->lock, flags);
3400 for (i = 0; i < num_eps; i++) {
3401 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3402 xhci_free_stream_info(xhci, vdev->eps[ep_index].stream_info);
3403 vdev->eps[ep_index].stream_info = NULL;
3404 /* FIXME Unset maxPstreams in endpoint context and
3405 * update deq ptr to point to normal string ring.
3406 */
3407 vdev->eps[ep_index].ep_state &= ~EP_GETTING_NO_STREAMS;
3408 vdev->eps[ep_index].ep_state &= ~EP_HAS_STREAMS;
3409 }
3410 spin_unlock_irqrestore(&xhci->lock, flags);
3411
3412 return 0;
3413}
3414
3415/*
3416 * Deletes endpoint resources for endpoints that were active before a Reset
3417 * Device command, or a Disable Slot command. The Reset Device command leaves
3418 * the control endpoint intact, whereas the Disable Slot command deletes it.
3419 *
3420 * Must be called with xhci->lock held.
3421 */
3422void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci,
3423 struct xhci_virt_device *virt_dev, bool drop_control_ep)
3424{
3425 int i;
3426 unsigned int num_dropped_eps = 0;
3427 unsigned int drop_flags = 0;
3428
3429 for (i = (drop_control_ep ? 0 : 1); i < 31; i++) {
3430 if (virt_dev->eps[i].ring) {
3431 drop_flags |= 1 << i;
3432 num_dropped_eps++;
3433 }
3434 }
3435 xhci->num_active_eps -= num_dropped_eps;
3436 if (num_dropped_eps)
3437 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
3438 "Dropped %u ep ctxs, flags = 0x%x, "
3439 "%u now active.",
3440 num_dropped_eps, drop_flags,
3441 xhci->num_active_eps);
3442}
3443
3444/*
3445 * This submits a Reset Device Command, which will set the device state to 0,
3446 * set the device address to 0, and disable all the endpoints except the default
3447 * control endpoint. The USB core should come back and call
3448 * xhci_address_device(), and then re-set up the configuration. If this is
3449 * called because of a usb_reset_and_verify_device(), then the old alternate
3450 * settings will be re-installed through the normal bandwidth allocation
3451 * functions.
3452 *
3453 * Wait for the Reset Device command to finish. Remove all structures
3454 * associated with the endpoints that were disabled. Clear the input device
3455 * structure? Cache the rings? Reset the control endpoint 0 max packet size?
3456 *
3457 * If the virt_dev to be reset does not exist or does not match the udev,
3458 * it means the device is lost, possibly due to the xHC restore error and
3459 * re-initialization during S3/S4. In this case, call xhci_alloc_dev() to
3460 * re-allocate the device.
3461 */
3462int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev)
3463{
3464 int ret, i;
3465 unsigned long flags;
3466 struct xhci_hcd *xhci;
3467 unsigned int slot_id;
3468 struct xhci_virt_device *virt_dev;
3469 struct xhci_command *reset_device_cmd;
3470 int last_freed_endpoint;
3471 struct xhci_slot_ctx *slot_ctx;
3472 int old_active_eps = 0;
3473
3474 ret = xhci_check_args(hcd, udev, NULL, 0, false, __func__);
3475 if (ret <= 0)
3476 return ret;
3477 xhci = hcd_to_xhci(hcd);
3478 slot_id = udev->slot_id;
3479 virt_dev = xhci->devs[slot_id];
3480 if (!virt_dev) {
3481 xhci_dbg(xhci, "The device to be reset with slot ID %u does "
3482 "not exist. Re-allocate the device\n", slot_id);
3483 ret = xhci_alloc_dev(hcd, udev);
3484 if (ret == 1)
3485 return 0;
3486 else
3487 return -EINVAL;
3488 }
3489
3490 if (virt_dev->tt_info)
3491 old_active_eps = virt_dev->tt_info->active_eps;
3492
3493 if (virt_dev->udev != udev) {
3494 /* If the virt_dev and the udev does not match, this virt_dev
3495 * may belong to another udev.
3496 * Re-allocate the device.
3497 */
3498 xhci_dbg(xhci, "The device to be reset with slot ID %u does "
3499 "not match the udev. Re-allocate the device\n",
3500 slot_id);
3501 ret = xhci_alloc_dev(hcd, udev);
3502 if (ret == 1)
3503 return 0;
3504 else
3505 return -EINVAL;
3506 }
3507
3508 /* If device is not setup, there is no point in resetting it */
3509 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
3510 if (GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)) ==
3511 SLOT_STATE_DISABLED)
3512 return 0;
3513
3514 xhci_dbg(xhci, "Resetting device with slot ID %u\n", slot_id);
3515 /* Allocate the command structure that holds the struct completion.
3516 * Assume we're in process context, since the normal device reset
3517 * process has to wait for the device anyway. Storage devices are
3518 * reset as part of error handling, so use GFP_NOIO instead of
3519 * GFP_KERNEL.
3520 */
3521 reset_device_cmd = xhci_alloc_command(xhci, false, true, GFP_NOIO);
3522 if (!reset_device_cmd) {
3523 xhci_dbg(xhci, "Couldn't allocate command structure.\n");
3524 return -ENOMEM;
3525 }
3526
3527 /* Attempt to submit the Reset Device command to the command ring */
3528 spin_lock_irqsave(&xhci->lock, flags);
3529
3530 ret = xhci_queue_reset_device(xhci, reset_device_cmd, slot_id);
3531 if (ret) {
3532 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3533 spin_unlock_irqrestore(&xhci->lock, flags);
3534 goto command_cleanup;
3535 }
3536 xhci_ring_cmd_db(xhci);
3537 spin_unlock_irqrestore(&xhci->lock, flags);
3538
3539 /* Wait for the Reset Device command to finish */
3540 wait_for_completion(reset_device_cmd->completion);
3541
3542 /* The Reset Device command can't fail, according to the 0.95/0.96 spec,
3543 * unless we tried to reset a slot ID that wasn't enabled,
3544 * or the device wasn't in the addressed or configured state.
3545 */
3546 ret = reset_device_cmd->status;
3547 switch (ret) {
3548 case COMP_CMD_ABORT:
3549 case COMP_CMD_STOP:
3550 xhci_warn(xhci, "Timeout waiting for reset device command\n");
3551 ret = -ETIME;
3552 goto command_cleanup;
3553 case COMP_EBADSLT: /* 0.95 completion code for bad slot ID */
3554 case COMP_CTX_STATE: /* 0.96 completion code for same thing */
3555 xhci_dbg(xhci, "Can't reset device (slot ID %u) in %s state\n",
3556 slot_id,
3557 xhci_get_slot_state(xhci, virt_dev->out_ctx));
3558 xhci_dbg(xhci, "Not freeing device rings.\n");
3559 /* Don't treat this as an error. May change my mind later. */
3560 ret = 0;
3561 goto command_cleanup;
3562 case COMP_SUCCESS:
3563 xhci_dbg(xhci, "Successful reset device command.\n");
3564 break;
3565 default:
3566 if (xhci_is_vendor_info_code(xhci, ret))
3567 break;
3568 xhci_warn(xhci, "Unknown completion code %u for "
3569 "reset device command.\n", ret);
3570 ret = -EINVAL;
3571 goto command_cleanup;
3572 }
3573
3574 /* Free up host controller endpoint resources */
3575 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) {
3576 spin_lock_irqsave(&xhci->lock, flags);
3577 /* Don't delete the default control endpoint resources */
3578 xhci_free_device_endpoint_resources(xhci, virt_dev, false);
3579 spin_unlock_irqrestore(&xhci->lock, flags);
3580 }
3581
3582 /* Everything but endpoint 0 is disabled, so free or cache the rings. */
3583 last_freed_endpoint = 1;
3584 for (i = 1; i < 31; ++i) {
3585 struct xhci_virt_ep *ep = &virt_dev->eps[i];
3586
3587 if (ep->ep_state & EP_HAS_STREAMS) {
3588 xhci_warn(xhci, "WARN: endpoint 0x%02x has streams on device reset, freeing streams.\n",
3589 xhci_get_endpoint_address(i));
3590 xhci_free_stream_info(xhci, ep->stream_info);
3591 ep->stream_info = NULL;
3592 ep->ep_state &= ~EP_HAS_STREAMS;
3593 }
3594
3595 if (ep->ring) {
3596 xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i);
3597 last_freed_endpoint = i;
3598 }
3599 if (!list_empty(&virt_dev->eps[i].bw_endpoint_list))
3600 xhci_drop_ep_from_interval_table(xhci,
3601 &virt_dev->eps[i].bw_info,
3602 virt_dev->bw_table,
3603 udev,
3604 &virt_dev->eps[i],
3605 virt_dev->tt_info);
3606 xhci_clear_endpoint_bw_info(&virt_dev->eps[i].bw_info);
3607 }
3608 /* If necessary, update the number of active TTs on this root port */
3609 xhci_update_tt_active_eps(xhci, virt_dev, old_active_eps);
3610
3611 xhci_dbg(xhci, "Output context after successful reset device cmd:\n");
3612 xhci_dbg_ctx(xhci, virt_dev->out_ctx, last_freed_endpoint);
3613 ret = 0;
3614
3615command_cleanup:
3616 xhci_free_command(xhci, reset_device_cmd);
3617 return ret;
3618}
3619
3620/*
3621 * At this point, the struct usb_device is about to go away, the device has
3622 * disconnected, and all traffic has been stopped and the endpoints have been
3623 * disabled. Free any HC data structures associated with that device.
3624 */
3625void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev)
3626{
3627 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3628 struct xhci_virt_device *virt_dev;
3629 unsigned long flags;
3630 u32 state;
3631 int i, ret;
3632 struct xhci_command *command;
3633
3634 command = xhci_alloc_command(xhci, false, false, GFP_KERNEL);
3635 if (!command)
3636 return;
3637
3638#ifndef CONFIG_USB_DEFAULT_PERSIST
3639 /*
3640 * We called pm_runtime_get_noresume when the device was attached.
3641 * Decrement the counter here to allow controller to runtime suspend
3642 * if no devices remain.
3643 */
3644 if (xhci->quirks & XHCI_RESET_ON_RESUME)
3645 pm_runtime_put_noidle(hcd->self.controller);
3646#endif
3647
3648 ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
3649 /* If the host is halted due to driver unload, we still need to free the
3650 * device.
3651 */
3652 if (ret <= 0 && ret != -ENODEV) {
3653 kfree(command);
3654 return;
3655 }
3656
3657 virt_dev = xhci->devs[udev->slot_id];
3658
3659 /* Stop any wayward timer functions (which may grab the lock) */
3660 for (i = 0; i < 31; ++i) {
3661 virt_dev->eps[i].ep_state &= ~EP_HALT_PENDING;
3662 del_timer_sync(&virt_dev->eps[i].stop_cmd_timer);
3663 }
3664
3665 spin_lock_irqsave(&xhci->lock, flags);
3666 /* Don't disable the slot if the host controller is dead. */
3667 state = readl(&xhci->op_regs->status);
3668 if (state == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING) ||
3669 (xhci->xhc_state & XHCI_STATE_HALTED)) {
3670 xhci_free_virt_device(xhci, udev->slot_id);
3671 spin_unlock_irqrestore(&xhci->lock, flags);
3672 kfree(command);
3673 return;
3674 }
3675
3676 if (xhci_queue_slot_control(xhci, command, TRB_DISABLE_SLOT,
3677 udev->slot_id)) {
3678 spin_unlock_irqrestore(&xhci->lock, flags);
3679 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3680 return;
3681 }
3682 xhci_ring_cmd_db(xhci);
3683 spin_unlock_irqrestore(&xhci->lock, flags);
3684
3685 /*
3686 * Event command completion handler will free any data structures
3687 * associated with the slot. XXX Can free sleep?
3688 */
3689}
3690
3691/*
3692 * Checks if we have enough host controller resources for the default control
3693 * endpoint.
3694 *
3695 * Must be called with xhci->lock held.
3696 */
3697static int xhci_reserve_host_control_ep_resources(struct xhci_hcd *xhci)
3698{
3699 if (xhci->num_active_eps + 1 > xhci->limit_active_eps) {
3700 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
3701 "Not enough ep ctxs: "
3702 "%u active, need to add 1, limit is %u.",
3703 xhci->num_active_eps, xhci->limit_active_eps);
3704 return -ENOMEM;
3705 }
3706 xhci->num_active_eps += 1;
3707 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
3708 "Adding 1 ep ctx, %u now active.",
3709 xhci->num_active_eps);
3710 return 0;
3711}
3712
3713
3714/*
3715 * Returns 0 if the xHC ran out of device slots, the Enable Slot command
3716 * timed out, or allocating memory failed. Returns 1 on success.
3717 */
3718int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev)
3719{
3720 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3721 unsigned long flags;
3722 int ret, slot_id;
3723 struct xhci_command *command;
3724
3725 command = xhci_alloc_command(xhci, false, false, GFP_KERNEL);
3726 if (!command)
3727 return 0;
3728
3729 /* xhci->slot_id and xhci->addr_dev are not thread-safe */
3730 mutex_lock(&xhci->mutex);
3731 spin_lock_irqsave(&xhci->lock, flags);
3732 command->completion = &xhci->addr_dev;
3733 ret = xhci_queue_slot_control(xhci, command, TRB_ENABLE_SLOT, 0);
3734 if (ret) {
3735 spin_unlock_irqrestore(&xhci->lock, flags);
3736 mutex_unlock(&xhci->mutex);
3737 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3738 kfree(command);
3739 return 0;
3740 }
3741 xhci_ring_cmd_db(xhci);
3742 spin_unlock_irqrestore(&xhci->lock, flags);
3743
3744 wait_for_completion(command->completion);
3745 slot_id = xhci->slot_id;
3746 mutex_unlock(&xhci->mutex);
3747
3748 if (!slot_id || command->status != COMP_SUCCESS) {
3749 xhci_err(xhci, "Error while assigning device slot ID\n");
3750 xhci_err(xhci, "Max number of devices this xHCI host supports is %u.\n",
3751 HCS_MAX_SLOTS(
3752 readl(&xhci->cap_regs->hcs_params1)));
3753 kfree(command);
3754 return 0;
3755 }
3756
3757 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) {
3758 spin_lock_irqsave(&xhci->lock, flags);
3759 ret = xhci_reserve_host_control_ep_resources(xhci);
3760 if (ret) {
3761 spin_unlock_irqrestore(&xhci->lock, flags);
3762 xhci_warn(xhci, "Not enough host resources, "
3763 "active endpoint contexts = %u\n",
3764 xhci->num_active_eps);
3765 goto disable_slot;
3766 }
3767 spin_unlock_irqrestore(&xhci->lock, flags);
3768 }
3769 /* Use GFP_NOIO, since this function can be called from
3770 * xhci_discover_or_reset_device(), which may be called as part of
3771 * mass storage driver error handling.
3772 */
3773 if (!xhci_alloc_virt_device(xhci, slot_id, udev, GFP_NOIO)) {
3774 xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n");
3775 goto disable_slot;
3776 }
3777 udev->slot_id = slot_id;
3778
3779#ifndef CONFIG_USB_DEFAULT_PERSIST
3780 /*
3781 * If resetting upon resume, we can't put the controller into runtime
3782 * suspend if there is a device attached.
3783 */
3784 if (xhci->quirks & XHCI_RESET_ON_RESUME)
3785 pm_runtime_get_noresume(hcd->self.controller);
3786#endif
3787
3788
3789 kfree(command);
3790 /* Is this a LS or FS device under a HS hub? */
3791 /* Hub or peripherial? */
3792 return 1;
3793
3794disable_slot:
3795 /* Disable slot, if we can do it without mem alloc */
3796 spin_lock_irqsave(&xhci->lock, flags);
3797 command->completion = NULL;
3798 command->status = 0;
3799 if (!xhci_queue_slot_control(xhci, command, TRB_DISABLE_SLOT,
3800 udev->slot_id))
3801 xhci_ring_cmd_db(xhci);
3802 spin_unlock_irqrestore(&xhci->lock, flags);
3803 return 0;
3804}
3805
3806/*
3807 * Issue an Address Device command and optionally send a corresponding
3808 * SetAddress request to the device.
3809 */
3810static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev,
3811 enum xhci_setup_dev setup)
3812{
3813 const char *act = setup == SETUP_CONTEXT_ONLY ? "context" : "address";
3814 unsigned long flags;
3815 struct xhci_virt_device *virt_dev;
3816 int ret = 0;
3817 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3818 struct xhci_slot_ctx *slot_ctx;
3819 struct xhci_input_control_ctx *ctrl_ctx;
3820 u64 temp_64;
3821 struct xhci_command *command = NULL;
3822
3823 mutex_lock(&xhci->mutex);
3824
3825 if (xhci->xhc_state) /* dying, removing or halted */
3826 goto out;
3827
3828 if (!udev->slot_id) {
3829 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3830 "Bad Slot ID %d", udev->slot_id);
3831 ret = -EINVAL;
3832 goto out;
3833 }
3834
3835 virt_dev = xhci->devs[udev->slot_id];
3836
3837 if (WARN_ON(!virt_dev)) {
3838 /*
3839 * In plug/unplug torture test with an NEC controller,
3840 * a zero-dereference was observed once due to virt_dev = 0.
3841 * Print useful debug rather than crash if it is observed again!
3842 */
3843 xhci_warn(xhci, "Virt dev invalid for slot_id 0x%x!\n",
3844 udev->slot_id);
3845 ret = -EINVAL;
3846 goto out;
3847 }
3848
3849 if (setup == SETUP_CONTEXT_ONLY) {
3850 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
3851 if (GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)) ==
3852 SLOT_STATE_DEFAULT) {
3853 xhci_dbg(xhci, "Slot already in default state\n");
3854 goto out;
3855 }
3856 }
3857
3858 command = xhci_alloc_command(xhci, false, false, GFP_KERNEL);
3859 if (!command) {
3860 ret = -ENOMEM;
3861 goto out;
3862 }
3863
3864 command->in_ctx = virt_dev->in_ctx;
3865 command->completion = &xhci->addr_dev;
3866
3867 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
3868 ctrl_ctx = xhci_get_input_control_ctx(virt_dev->in_ctx);
3869 if (!ctrl_ctx) {
3870 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
3871 __func__);
3872 ret = -EINVAL;
3873 goto out;
3874 }
3875 /*
3876 * If this is the first Set Address since device plug-in or
3877 * virt_device realloaction after a resume with an xHCI power loss,
3878 * then set up the slot context.
3879 */
3880 if (!slot_ctx->dev_info)
3881 xhci_setup_addressable_virt_dev(xhci, udev);
3882 /* Otherwise, update the control endpoint ring enqueue pointer. */
3883 else
3884 xhci_copy_ep0_dequeue_into_input_ctx(xhci, udev);
3885 ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG);
3886 ctrl_ctx->drop_flags = 0;
3887
3888 xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
3889 xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
3890 trace_xhci_address_ctx(xhci, virt_dev->in_ctx,
3891 le32_to_cpu(slot_ctx->dev_info) >> 27);
3892
3893 spin_lock_irqsave(&xhci->lock, flags);
3894 ret = xhci_queue_address_device(xhci, command, virt_dev->in_ctx->dma,
3895 udev->slot_id, setup);
3896 if (ret) {
3897 spin_unlock_irqrestore(&xhci->lock, flags);
3898 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3899 "FIXME: allocate a command ring segment");
3900 goto out;
3901 }
3902 xhci_ring_cmd_db(xhci);
3903 spin_unlock_irqrestore(&xhci->lock, flags);
3904
3905 /* ctrl tx can take up to 5 sec; XXX: need more time for xHC? */
3906 wait_for_completion(command->completion);
3907
3908 /* FIXME: From section 4.3.4: "Software shall be responsible for timing
3909 * the SetAddress() "recovery interval" required by USB and aborting the
3910 * command on a timeout.
3911 */
3912 switch (command->status) {
3913 case COMP_CMD_ABORT:
3914 case COMP_CMD_STOP:
3915 xhci_warn(xhci, "Timeout while waiting for setup device command\n");
3916 ret = -ETIME;
3917 break;
3918 case COMP_CTX_STATE:
3919 case COMP_EBADSLT:
3920 xhci_err(xhci, "Setup ERROR: setup %s command for slot %d.\n",
3921 act, udev->slot_id);
3922 ret = -EINVAL;
3923 break;
3924 case COMP_TX_ERR:
3925 dev_warn(&udev->dev, "Device not responding to setup %s.\n", act);
3926 ret = -EPROTO;
3927 break;
3928 case COMP_DEV_ERR:
3929 dev_warn(&udev->dev,
3930 "ERROR: Incompatible device for setup %s command\n", act);
3931 ret = -ENODEV;
3932 break;
3933 case COMP_SUCCESS:
3934 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3935 "Successful setup %s command", act);
3936 break;
3937 default:
3938 xhci_err(xhci,
3939 "ERROR: unexpected setup %s command completion code 0x%x.\n",
3940 act, command->status);
3941 xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
3942 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2);
3943 trace_xhci_address_ctx(xhci, virt_dev->out_ctx, 1);
3944 ret = -EINVAL;
3945 break;
3946 }
3947 if (ret)
3948 goto out;
3949 temp_64 = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
3950 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3951 "Op regs DCBAA ptr = %#016llx", temp_64);
3952 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3953 "Slot ID %d dcbaa entry @%p = %#016llx",
3954 udev->slot_id,
3955 &xhci->dcbaa->dev_context_ptrs[udev->slot_id],
3956 (unsigned long long)
3957 le64_to_cpu(xhci->dcbaa->dev_context_ptrs[udev->slot_id]));
3958 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3959 "Output Context DMA address = %#08llx",
3960 (unsigned long long)virt_dev->out_ctx->dma);
3961 xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
3962 xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
3963 trace_xhci_address_ctx(xhci, virt_dev->in_ctx,
3964 le32_to_cpu(slot_ctx->dev_info) >> 27);
3965 xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
3966 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2);
3967 /*
3968 * USB core uses address 1 for the roothubs, so we add one to the
3969 * address given back to us by the HC.
3970 */
3971 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
3972 trace_xhci_address_ctx(xhci, virt_dev->out_ctx,
3973 le32_to_cpu(slot_ctx->dev_info) >> 27);
3974 /* Zero the input context control for later use */
3975 ctrl_ctx->add_flags = 0;
3976 ctrl_ctx->drop_flags = 0;
3977
3978 xhci_dbg_trace(xhci, trace_xhci_dbg_address,
3979 "Internal device address = %d",
3980 le32_to_cpu(slot_ctx->dev_state) & DEV_ADDR_MASK);
3981out:
3982 mutex_unlock(&xhci->mutex);
3983 kfree(command);
3984 return ret;
3985}
3986
3987int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
3988{
3989 return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ADDRESS);
3990}
3991
3992int xhci_enable_device(struct usb_hcd *hcd, struct usb_device *udev)
3993{
3994 return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ONLY);
3995}
3996
3997/*
3998 * Transfer the port index into real index in the HW port status
3999 * registers. Caculate offset between the port's PORTSC register
4000 * and port status base. Divide the number of per port register
4001 * to get the real index. The raw port number bases 1.
4002 */
4003int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1)
4004{
4005 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4006 __le32 __iomem *base_addr = &xhci->op_regs->port_status_base;
4007 __le32 __iomem *addr;
4008 int raw_port;
4009
4010 if (hcd->speed < HCD_USB3)
4011 addr = xhci->usb2_ports[port1 - 1];
4012 else
4013 addr = xhci->usb3_ports[port1 - 1];
4014
4015 raw_port = (addr - base_addr)/NUM_PORT_REGS + 1;
4016 return raw_port;
4017}
4018
4019/*
4020 * Issue an Evaluate Context command to change the Maximum Exit Latency in the
4021 * slot context. If that succeeds, store the new MEL in the xhci_virt_device.
4022 */
4023static int __maybe_unused xhci_change_max_exit_latency(struct xhci_hcd *xhci,
4024 struct usb_device *udev, u16 max_exit_latency)
4025{
4026 struct xhci_virt_device *virt_dev;
4027 struct xhci_command *command;
4028 struct xhci_input_control_ctx *ctrl_ctx;
4029 struct xhci_slot_ctx *slot_ctx;
4030 unsigned long flags;
4031 int ret;
4032
4033 spin_lock_irqsave(&xhci->lock, flags);
4034
4035 virt_dev = xhci->devs[udev->slot_id];
4036
4037 /*
4038 * virt_dev might not exists yet if xHC resumed from hibernate (S4) and
4039 * xHC was re-initialized. Exit latency will be set later after
4040 * hub_port_finish_reset() is done and xhci->devs[] are re-allocated
4041 */
4042
4043 if (!virt_dev || max_exit_latency == virt_dev->current_mel) {
4044 spin_unlock_irqrestore(&xhci->lock, flags);
4045 return 0;
4046 }
4047
4048 /* Attempt to issue an Evaluate Context command to change the MEL. */
4049 command = xhci->lpm_command;
4050 ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
4051 if (!ctrl_ctx) {
4052 spin_unlock_irqrestore(&xhci->lock, flags);
4053 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
4054 __func__);
4055 return -ENOMEM;
4056 }
4057
4058 xhci_slot_copy(xhci, command->in_ctx, virt_dev->out_ctx);
4059 spin_unlock_irqrestore(&xhci->lock, flags);
4060
4061 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
4062 slot_ctx = xhci_get_slot_ctx(xhci, command->in_ctx);
4063 slot_ctx->dev_info2 &= cpu_to_le32(~((u32) MAX_EXIT));
4064 slot_ctx->dev_info2 |= cpu_to_le32(max_exit_latency);
4065 slot_ctx->dev_state = 0;
4066
4067 xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
4068 "Set up evaluate context for LPM MEL change.");
4069 xhci_dbg(xhci, "Slot %u Input Context:\n", udev->slot_id);
4070 xhci_dbg_ctx(xhci, command->in_ctx, 0);
4071
4072 /* Issue and wait for the evaluate context command. */
4073 ret = xhci_configure_endpoint(xhci, udev, command,
4074 true, true);
4075 xhci_dbg(xhci, "Slot %u Output Context:\n", udev->slot_id);
4076 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 0);
4077
4078 if (!ret) {
4079 spin_lock_irqsave(&xhci->lock, flags);
4080 virt_dev->current_mel = max_exit_latency;
4081 spin_unlock_irqrestore(&xhci->lock, flags);
4082 }
4083 return ret;
4084}
4085
4086#ifdef CONFIG_PM
4087
4088/* BESL to HIRD Encoding array for USB2 LPM */
4089static int xhci_besl_encoding[16] = {125, 150, 200, 300, 400, 500, 1000, 2000,
4090 3000, 4000, 5000, 6000, 7000, 8000, 9000, 10000};
4091
4092/* Calculate HIRD/BESL for USB2 PORTPMSC*/
4093static int xhci_calculate_hird_besl(struct xhci_hcd *xhci,
4094 struct usb_device *udev)
4095{
4096 int u2del, besl, besl_host;
4097 int besl_device = 0;
4098 u32 field;
4099
4100 u2del = HCS_U2_LATENCY(xhci->hcs_params3);
4101 field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);
4102
4103 if (field & USB_BESL_SUPPORT) {
4104 for (besl_host = 0; besl_host < 16; besl_host++) {
4105 if (xhci_besl_encoding[besl_host] >= u2del)
4106 break;
4107 }
4108 /* Use baseline BESL value as default */
4109 if (field & USB_BESL_BASELINE_VALID)
4110 besl_device = USB_GET_BESL_BASELINE(field);
4111 else if (field & USB_BESL_DEEP_VALID)
4112 besl_device = USB_GET_BESL_DEEP(field);
4113 } else {
4114 if (u2del <= 50)
4115 besl_host = 0;
4116 else
4117 besl_host = (u2del - 51) / 75 + 1;
4118 }
4119
4120 besl = besl_host + besl_device;
4121 if (besl > 15)
4122 besl = 15;
4123
4124 return besl;
4125}
4126
4127/* Calculate BESLD, L1 timeout and HIRDM for USB2 PORTHLPMC */
4128static int xhci_calculate_usb2_hw_lpm_params(struct usb_device *udev)
4129{
4130 u32 field;
4131 int l1;
4132 int besld = 0;
4133 int hirdm = 0;
4134
4135 field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);
4136
4137 /* xHCI l1 is set in steps of 256us, xHCI 1.0 section 5.4.11.2 */
4138 l1 = udev->l1_params.timeout / 256;
4139
4140 /* device has preferred BESLD */
4141 if (field & USB_BESL_DEEP_VALID) {
4142 besld = USB_GET_BESL_DEEP(field);
4143 hirdm = 1;
4144 }
4145
4146 return PORT_BESLD(besld) | PORT_L1_TIMEOUT(l1) | PORT_HIRDM(hirdm);
4147}
4148
4149int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
4150 struct usb_device *udev, int enable)
4151{
4152 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4153 __le32 __iomem **port_array;
4154 __le32 __iomem *pm_addr, *hlpm_addr;
4155 u32 pm_val, hlpm_val, field;
4156 unsigned int port_num;
4157 unsigned long flags;
4158 int hird, exit_latency;
4159 int ret;
4160
4161 if (hcd->speed >= HCD_USB3 || !xhci->hw_lpm_support ||
4162 !udev->lpm_capable)
4163 return -EPERM;
4164
4165 if (!udev->parent || udev->parent->parent ||
4166 udev->descriptor.bDeviceClass == USB_CLASS_HUB)
4167 return -EPERM;
4168
4169 if (udev->usb2_hw_lpm_capable != 1)
4170 return -EPERM;
4171
4172 spin_lock_irqsave(&xhci->lock, flags);
4173
4174 port_array = xhci->usb2_ports;
4175 port_num = udev->portnum - 1;
4176 pm_addr = port_array[port_num] + PORTPMSC;
4177 pm_val = readl(pm_addr);
4178 hlpm_addr = port_array[port_num] + PORTHLPMC;
4179 field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);
4180
4181 xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
4182 enable ? "enable" : "disable", port_num + 1);
4183
4184 if (enable) {
4185 /* Host supports BESL timeout instead of HIRD */
4186 if (udev->usb2_hw_lpm_besl_capable) {
4187 /* if device doesn't have a preferred BESL value use a
4188 * default one which works with mixed HIRD and BESL
4189 * systems. See XHCI_DEFAULT_BESL definition in xhci.h
4190 */
4191 if ((field & USB_BESL_SUPPORT) &&
4192 (field & USB_BESL_BASELINE_VALID))
4193 hird = USB_GET_BESL_BASELINE(field);
4194 else
4195 hird = udev->l1_params.besl;
4196
4197 exit_latency = xhci_besl_encoding[hird];
4198 spin_unlock_irqrestore(&xhci->lock, flags);
4199
4200 /* USB 3.0 code dedicate one xhci->lpm_command->in_ctx
4201 * input context for link powermanagement evaluate
4202 * context commands. It is protected by hcd->bandwidth
4203 * mutex and is shared by all devices. We need to set
4204 * the max ext latency in USB 2 BESL LPM as well, so
4205 * use the same mutex and xhci_change_max_exit_latency()
4206 */
4207 mutex_lock(hcd->bandwidth_mutex);
4208 ret = xhci_change_max_exit_latency(xhci, udev,
4209 exit_latency);
4210 mutex_unlock(hcd->bandwidth_mutex);
4211
4212 if (ret < 0)
4213 return ret;
4214 spin_lock_irqsave(&xhci->lock, flags);
4215
4216 hlpm_val = xhci_calculate_usb2_hw_lpm_params(udev);
4217 writel(hlpm_val, hlpm_addr);
4218 /* flush write */
4219 readl(hlpm_addr);
4220 } else {
4221 hird = xhci_calculate_hird_besl(xhci, udev);
4222 }
4223
4224 pm_val &= ~PORT_HIRD_MASK;
4225 pm_val |= PORT_HIRD(hird) | PORT_RWE | PORT_L1DS(udev->slot_id);
4226 writel(pm_val, pm_addr);
4227 pm_val = readl(pm_addr);
4228 pm_val |= PORT_HLE;
4229 writel(pm_val, pm_addr);
4230 /* flush write */
4231 readl(pm_addr);
4232 } else {
4233 pm_val &= ~(PORT_HLE | PORT_RWE | PORT_HIRD_MASK | PORT_L1DS_MASK);
4234 writel(pm_val, pm_addr);
4235 /* flush write */
4236 readl(pm_addr);
4237 if (udev->usb2_hw_lpm_besl_capable) {
4238 spin_unlock_irqrestore(&xhci->lock, flags);
4239 mutex_lock(hcd->bandwidth_mutex);
4240 xhci_change_max_exit_latency(xhci, udev, 0);
4241 mutex_unlock(hcd->bandwidth_mutex);
4242 return 0;
4243 }
4244 }
4245
4246 spin_unlock_irqrestore(&xhci->lock, flags);
4247 return 0;
4248}
4249
4250/* check if a usb2 port supports a given extened capability protocol
4251 * only USB2 ports extended protocol capability values are cached.
4252 * Return 1 if capability is supported
4253 */
4254static int xhci_check_usb2_port_capability(struct xhci_hcd *xhci, int port,
4255 unsigned capability)
4256{
4257 u32 port_offset, port_count;
4258 int i;
4259
4260 for (i = 0; i < xhci->num_ext_caps; i++) {
4261 if (xhci->ext_caps[i] & capability) {
4262 /* port offsets starts at 1 */
4263 port_offset = XHCI_EXT_PORT_OFF(xhci->ext_caps[i]) - 1;
4264 port_count = XHCI_EXT_PORT_COUNT(xhci->ext_caps[i]);
4265 if (port >= port_offset &&
4266 port < port_offset + port_count)
4267 return 1;
4268 }
4269 }
4270 return 0;
4271}
4272
4273int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
4274{
4275 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4276 int portnum = udev->portnum - 1;
4277
4278 if (hcd->speed >= HCD_USB3 || !xhci->sw_lpm_support ||
4279 !udev->lpm_capable)
4280 return 0;
4281
4282 /* we only support lpm for non-hub device connected to root hub yet */
4283 if (!udev->parent || udev->parent->parent ||
4284 udev->descriptor.bDeviceClass == USB_CLASS_HUB)
4285 return 0;
4286
4287 if (xhci->hw_lpm_support == 1 &&
4288 xhci_check_usb2_port_capability(
4289 xhci, portnum, XHCI_HLC)) {
4290 udev->usb2_hw_lpm_capable = 1;
4291 udev->l1_params.timeout = XHCI_L1_TIMEOUT;
4292 udev->l1_params.besl = XHCI_DEFAULT_BESL;
4293 if (xhci_check_usb2_port_capability(xhci, portnum,
4294 XHCI_BLC))
4295 udev->usb2_hw_lpm_besl_capable = 1;
4296 }
4297
4298 return 0;
4299}
4300
4301/*---------------------- USB 3.0 Link PM functions ------------------------*/
4302
4303/* Service interval in nanoseconds = 2^(bInterval - 1) * 125us * 1000ns / 1us */
4304static unsigned long long xhci_service_interval_to_ns(
4305 struct usb_endpoint_descriptor *desc)
4306{
4307 return (1ULL << (desc->bInterval - 1)) * 125 * 1000;
4308}
4309
4310static u16 xhci_get_timeout_no_hub_lpm(struct usb_device *udev,
4311 enum usb3_link_state state)
4312{
4313 unsigned long long sel;
4314 unsigned long long pel;
4315 unsigned int max_sel_pel;
4316 char *state_name;
4317
4318 switch (state) {
4319 case USB3_LPM_U1:
4320 /* Convert SEL and PEL stored in nanoseconds to microseconds */
4321 sel = DIV_ROUND_UP(udev->u1_params.sel, 1000);
4322 pel = DIV_ROUND_UP(udev->u1_params.pel, 1000);
4323 max_sel_pel = USB3_LPM_MAX_U1_SEL_PEL;
4324 state_name = "U1";
4325 break;
4326 case USB3_LPM_U2:
4327 sel = DIV_ROUND_UP(udev->u2_params.sel, 1000);
4328 pel = DIV_ROUND_UP(udev->u2_params.pel, 1000);
4329 max_sel_pel = USB3_LPM_MAX_U2_SEL_PEL;
4330 state_name = "U2";
4331 break;
4332 default:
4333 dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
4334 __func__);
4335 return USB3_LPM_DISABLED;
4336 }
4337
4338 if (sel <= max_sel_pel && pel <= max_sel_pel)
4339 return USB3_LPM_DEVICE_INITIATED;
4340
4341 if (sel > max_sel_pel)
4342 dev_dbg(&udev->dev, "Device-initiated %s disabled "
4343 "due to long SEL %llu ms\n",
4344 state_name, sel);
4345 else
4346 dev_dbg(&udev->dev, "Device-initiated %s disabled "
4347 "due to long PEL %llu ms\n",
4348 state_name, pel);
4349 return USB3_LPM_DISABLED;
4350}
4351
4352/* The U1 timeout should be the maximum of the following values:
4353 * - For control endpoints, U1 system exit latency (SEL) * 3
4354 * - For bulk endpoints, U1 SEL * 5
4355 * - For interrupt endpoints:
4356 * - Notification EPs, U1 SEL * 3
4357 * - Periodic EPs, max(105% of bInterval, U1 SEL * 2)
4358 * - For isochronous endpoints, max(105% of bInterval, U1 SEL * 2)
4359 */
4360static unsigned long long xhci_calculate_intel_u1_timeout(
4361 struct usb_device *udev,
4362 struct usb_endpoint_descriptor *desc)
4363{
4364 unsigned long long timeout_ns;
4365 int ep_type;
4366 int intr_type;
4367
4368 ep_type = usb_endpoint_type(desc);
4369 switch (ep_type) {
4370 case USB_ENDPOINT_XFER_CONTROL:
4371 timeout_ns = udev->u1_params.sel * 3;
4372 break;
4373 case USB_ENDPOINT_XFER_BULK:
4374 timeout_ns = udev->u1_params.sel * 5;
4375 break;
4376 case USB_ENDPOINT_XFER_INT:
4377 intr_type = usb_endpoint_interrupt_type(desc);
4378 if (intr_type == USB_ENDPOINT_INTR_NOTIFICATION) {
4379 timeout_ns = udev->u1_params.sel * 3;
4380 break;
4381 }
4382 /* Otherwise the calculation is the same as isoc eps */
4383 case USB_ENDPOINT_XFER_ISOC:
4384 timeout_ns = xhci_service_interval_to_ns(desc);
4385 timeout_ns = DIV_ROUND_UP_ULL(timeout_ns * 105, 100);
4386 if (timeout_ns < udev->u1_params.sel * 2)
4387 timeout_ns = udev->u1_params.sel * 2;
4388 break;
4389 default:
4390 return 0;
4391 }
4392
4393 return timeout_ns;
4394}
4395
4396/* Returns the hub-encoded U1 timeout value. */
4397static u16 xhci_calculate_u1_timeout(struct xhci_hcd *xhci,
4398 struct usb_device *udev,
4399 struct usb_endpoint_descriptor *desc)
4400{
4401 unsigned long long timeout_ns;
4402
4403 if (xhci->quirks & XHCI_INTEL_HOST)
4404 timeout_ns = xhci_calculate_intel_u1_timeout(udev, desc);
4405 else
4406 timeout_ns = udev->u1_params.sel;
4407
4408 /* The U1 timeout is encoded in 1us intervals.
4409 * Don't return a timeout of zero, because that's USB3_LPM_DISABLED.
4410 */
4411 if (timeout_ns == USB3_LPM_DISABLED)
4412 timeout_ns = 1;
4413 else
4414 timeout_ns = DIV_ROUND_UP_ULL(timeout_ns, 1000);
4415
4416 /* If the necessary timeout value is bigger than what we can set in the
4417 * USB 3.0 hub, we have to disable hub-initiated U1.
4418 */
4419 if (timeout_ns <= USB3_LPM_U1_MAX_TIMEOUT)
4420 return timeout_ns;
4421 dev_dbg(&udev->dev, "Hub-initiated U1 disabled "
4422 "due to long timeout %llu ms\n", timeout_ns);
4423 return xhci_get_timeout_no_hub_lpm(udev, USB3_LPM_U1);
4424}
4425
4426/* The U2 timeout should be the maximum of:
4427 * - 10 ms (to avoid the bandwidth impact on the scheduler)
4428 * - largest bInterval of any active periodic endpoint (to avoid going
4429 * into lower power link states between intervals).
4430 * - the U2 Exit Latency of the device
4431 */
4432static unsigned long long xhci_calculate_intel_u2_timeout(
4433 struct usb_device *udev,
4434 struct usb_endpoint_descriptor *desc)
4435{
4436 unsigned long long timeout_ns;
4437 unsigned long long u2_del_ns;
4438
4439 timeout_ns = 10 * 1000 * 1000;
4440
4441 if ((usb_endpoint_xfer_int(desc) || usb_endpoint_xfer_isoc(desc)) &&
4442 (xhci_service_interval_to_ns(desc) > timeout_ns))
4443 timeout_ns = xhci_service_interval_to_ns(desc);
4444
4445 u2_del_ns = le16_to_cpu(udev->bos->ss_cap->bU2DevExitLat) * 1000ULL;
4446 if (u2_del_ns > timeout_ns)
4447 timeout_ns = u2_del_ns;
4448
4449 return timeout_ns;
4450}
4451
4452/* Returns the hub-encoded U2 timeout value. */
4453static u16 xhci_calculate_u2_timeout(struct xhci_hcd *xhci,
4454 struct usb_device *udev,
4455 struct usb_endpoint_descriptor *desc)
4456{
4457 unsigned long long timeout_ns;
4458
4459 if (xhci->quirks & XHCI_INTEL_HOST)
4460 timeout_ns = xhci_calculate_intel_u2_timeout(udev, desc);
4461 else
4462 timeout_ns = udev->u2_params.sel;
4463
4464 /* The U2 timeout is encoded in 256us intervals */
4465 timeout_ns = DIV_ROUND_UP_ULL(timeout_ns, 256 * 1000);
4466 /* If the necessary timeout value is bigger than what we can set in the
4467 * USB 3.0 hub, we have to disable hub-initiated U2.
4468 */
4469 if (timeout_ns <= USB3_LPM_U2_MAX_TIMEOUT)
4470 return timeout_ns;
4471 dev_dbg(&udev->dev, "Hub-initiated U2 disabled "
4472 "due to long timeout %llu ms\n", timeout_ns);
4473 return xhci_get_timeout_no_hub_lpm(udev, USB3_LPM_U2);
4474}
4475
4476static u16 xhci_call_host_update_timeout_for_endpoint(struct xhci_hcd *xhci,
4477 struct usb_device *udev,
4478 struct usb_endpoint_descriptor *desc,
4479 enum usb3_link_state state,
4480 u16 *timeout)
4481{
4482 if (state == USB3_LPM_U1)
4483 return xhci_calculate_u1_timeout(xhci, udev, desc);
4484 else if (state == USB3_LPM_U2)
4485 return xhci_calculate_u2_timeout(xhci, udev, desc);
4486
4487 return USB3_LPM_DISABLED;
4488}
4489
4490static int xhci_update_timeout_for_endpoint(struct xhci_hcd *xhci,
4491 struct usb_device *udev,
4492 struct usb_endpoint_descriptor *desc,
4493 enum usb3_link_state state,
4494 u16 *timeout)
4495{
4496 u16 alt_timeout;
4497
4498 alt_timeout = xhci_call_host_update_timeout_for_endpoint(xhci, udev,
4499 desc, state, timeout);
4500
4501 /* If we found we can't enable hub-initiated LPM, or
4502 * the U1 or U2 exit latency was too high to allow
4503 * device-initiated LPM as well, just stop searching.
4504 */
4505 if (alt_timeout == USB3_LPM_DISABLED ||
4506 alt_timeout == USB3_LPM_DEVICE_INITIATED) {
4507 *timeout = alt_timeout;
4508 return -E2BIG;
4509 }
4510 if (alt_timeout > *timeout)
4511 *timeout = alt_timeout;
4512 return 0;
4513}
4514
4515static int xhci_update_timeout_for_interface(struct xhci_hcd *xhci,
4516 struct usb_device *udev,
4517 struct usb_host_interface *alt,
4518 enum usb3_link_state state,
4519 u16 *timeout)
4520{
4521 int j;
4522
4523 for (j = 0; j < alt->desc.bNumEndpoints; j++) {
4524 if (xhci_update_timeout_for_endpoint(xhci, udev,
4525 &alt->endpoint[j].desc, state, timeout))
4526 return -E2BIG;
4527 continue;
4528 }
4529 return 0;
4530}
4531
4532static int xhci_check_intel_tier_policy(struct usb_device *udev,
4533 enum usb3_link_state state)
4534{
4535 struct usb_device *parent;
4536 unsigned int num_hubs;
4537
4538 if (state == USB3_LPM_U2)
4539 return 0;
4540
4541 /* Don't enable U1 if the device is on a 2nd tier hub or lower. */
4542 for (parent = udev->parent, num_hubs = 0; parent->parent;
4543 parent = parent->parent)
4544 num_hubs++;
4545
4546 if (num_hubs < 2)
4547 return 0;
4548
4549 dev_dbg(&udev->dev, "Disabling U1 link state for device"
4550 " below second-tier hub.\n");
4551 dev_dbg(&udev->dev, "Plug device into first-tier hub "
4552 "to decrease power consumption.\n");
4553 return -E2BIG;
4554}
4555
4556static int xhci_check_tier_policy(struct xhci_hcd *xhci,
4557 struct usb_device *udev,
4558 enum usb3_link_state state)
4559{
4560 if (xhci->quirks & XHCI_INTEL_HOST)
4561 return xhci_check_intel_tier_policy(udev, state);
4562 else
4563 return 0;
4564}
4565
4566/* Returns the U1 or U2 timeout that should be enabled.
4567 * If the tier check or timeout setting functions return with a non-zero exit
4568 * code, that means the timeout value has been finalized and we shouldn't look
4569 * at any more endpoints.
4570 */
4571static u16 xhci_calculate_lpm_timeout(struct usb_hcd *hcd,
4572 struct usb_device *udev, enum usb3_link_state state)
4573{
4574 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4575 struct usb_host_config *config;
4576 char *state_name;
4577 int i;
4578 u16 timeout = USB3_LPM_DISABLED;
4579
4580 if (state == USB3_LPM_U1)
4581 state_name = "U1";
4582 else if (state == USB3_LPM_U2)
4583 state_name = "U2";
4584 else {
4585 dev_warn(&udev->dev, "Can't enable unknown link state %i\n",
4586 state);
4587 return timeout;
4588 }
4589
4590 if (xhci_check_tier_policy(xhci, udev, state) < 0)
4591 return timeout;
4592
4593 /* Gather some information about the currently installed configuration
4594 * and alternate interface settings.
4595 */
4596 if (xhci_update_timeout_for_endpoint(xhci, udev, &udev->ep0.desc,
4597 state, &timeout))
4598 return timeout;
4599
4600 config = udev->actconfig;
4601 if (!config)
4602 return timeout;
4603
4604 for (i = 0; i < config->desc.bNumInterfaces; i++) {
4605 struct usb_driver *driver;
4606 struct usb_interface *intf = config->interface[i];
4607
4608 if (!intf)
4609 continue;
4610
4611 /* Check if any currently bound drivers want hub-initiated LPM
4612 * disabled.
4613 */
4614 if (intf->dev.driver) {
4615 driver = to_usb_driver(intf->dev.driver);
4616 if (driver && driver->disable_hub_initiated_lpm) {
4617 dev_dbg(&udev->dev, "Hub-initiated %s disabled "
4618 "at request of driver %s\n",
4619 state_name, driver->name);
4620 return xhci_get_timeout_no_hub_lpm(udev, state);
4621 }
4622 }
4623
4624 /* Not sure how this could happen... */
4625 if (!intf->cur_altsetting)
4626 continue;
4627
4628 if (xhci_update_timeout_for_interface(xhci, udev,
4629 intf->cur_altsetting,
4630 state, &timeout))
4631 return timeout;
4632 }
4633 return timeout;
4634}
4635
4636static int calculate_max_exit_latency(struct usb_device *udev,
4637 enum usb3_link_state state_changed,
4638 u16 hub_encoded_timeout)
4639{
4640 unsigned long long u1_mel_us = 0;
4641 unsigned long long u2_mel_us = 0;
4642 unsigned long long mel_us = 0;
4643 bool disabling_u1;
4644 bool disabling_u2;
4645 bool enabling_u1;
4646 bool enabling_u2;
4647
4648 disabling_u1 = (state_changed == USB3_LPM_U1 &&
4649 hub_encoded_timeout == USB3_LPM_DISABLED);
4650 disabling_u2 = (state_changed == USB3_LPM_U2 &&
4651 hub_encoded_timeout == USB3_LPM_DISABLED);
4652
4653 enabling_u1 = (state_changed == USB3_LPM_U1 &&
4654 hub_encoded_timeout != USB3_LPM_DISABLED);
4655 enabling_u2 = (state_changed == USB3_LPM_U2 &&
4656 hub_encoded_timeout != USB3_LPM_DISABLED);
4657
4658 /* If U1 was already enabled and we're not disabling it,
4659 * or we're going to enable U1, account for the U1 max exit latency.
4660 */
4661 if ((udev->u1_params.timeout != USB3_LPM_DISABLED && !disabling_u1) ||
4662 enabling_u1)
4663 u1_mel_us = DIV_ROUND_UP(udev->u1_params.mel, 1000);
4664 if ((udev->u2_params.timeout != USB3_LPM_DISABLED && !disabling_u2) ||
4665 enabling_u2)
4666 u2_mel_us = DIV_ROUND_UP(udev->u2_params.mel, 1000);
4667
4668 if (u1_mel_us > u2_mel_us)
4669 mel_us = u1_mel_us;
4670 else
4671 mel_us = u2_mel_us;
4672 /* xHCI host controller max exit latency field is only 16 bits wide. */
4673 if (mel_us > MAX_EXIT) {
4674 dev_warn(&udev->dev, "Link PM max exit latency of %lluus "
4675 "is too big.\n", mel_us);
4676 return -E2BIG;
4677 }
4678 return mel_us;
4679}
4680
4681/* Returns the USB3 hub-encoded value for the U1/U2 timeout. */
4682int xhci_enable_usb3_lpm_timeout(struct usb_hcd *hcd,
4683 struct usb_device *udev, enum usb3_link_state state)
4684{
4685 struct xhci_hcd *xhci;
4686 u16 hub_encoded_timeout;
4687 int mel;
4688 int ret;
4689
4690 xhci = hcd_to_xhci(hcd);
4691 /* The LPM timeout values are pretty host-controller specific, so don't
4692 * enable hub-initiated timeouts unless the vendor has provided
4693 * information about their timeout algorithm.
4694 */
4695 if (!xhci || !(xhci->quirks & XHCI_LPM_SUPPORT) ||
4696 !xhci->devs[udev->slot_id])
4697 return USB3_LPM_DISABLED;
4698
4699 hub_encoded_timeout = xhci_calculate_lpm_timeout(hcd, udev, state);
4700 mel = calculate_max_exit_latency(udev, state, hub_encoded_timeout);
4701 if (mel < 0) {
4702 /* Max Exit Latency is too big, disable LPM. */
4703 hub_encoded_timeout = USB3_LPM_DISABLED;
4704 mel = 0;
4705 }
4706
4707 ret = xhci_change_max_exit_latency(xhci, udev, mel);
4708 if (ret)
4709 return ret;
4710 return hub_encoded_timeout;
4711}
4712
4713int xhci_disable_usb3_lpm_timeout(struct usb_hcd *hcd,
4714 struct usb_device *udev, enum usb3_link_state state)
4715{
4716 struct xhci_hcd *xhci;
4717 u16 mel;
4718
4719 xhci = hcd_to_xhci(hcd);
4720 if (!xhci || !(xhci->quirks & XHCI_LPM_SUPPORT) ||
4721 !xhci->devs[udev->slot_id])
4722 return 0;
4723
4724 mel = calculate_max_exit_latency(udev, state, USB3_LPM_DISABLED);
4725 return xhci_change_max_exit_latency(xhci, udev, mel);
4726}
4727#else /* CONFIG_PM */
4728
4729int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
4730 struct usb_device *udev, int enable)
4731{
4732 return 0;
4733}
4734
4735int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
4736{
4737 return 0;
4738}
4739
4740int xhci_enable_usb3_lpm_timeout(struct usb_hcd *hcd,
4741 struct usb_device *udev, enum usb3_link_state state)
4742{
4743 return USB3_LPM_DISABLED;
4744}
4745
4746int xhci_disable_usb3_lpm_timeout(struct usb_hcd *hcd,
4747 struct usb_device *udev, enum usb3_link_state state)
4748{
4749 return 0;
4750}
4751#endif /* CONFIG_PM */
4752
4753/*-------------------------------------------------------------------------*/
4754
4755/* Once a hub descriptor is fetched for a device, we need to update the xHC's
4756 * internal data structures for the device.
4757 */
4758int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
4759 struct usb_tt *tt, gfp_t mem_flags)
4760{
4761 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4762 struct xhci_virt_device *vdev;
4763 struct xhci_command *config_cmd;
4764 struct xhci_input_control_ctx *ctrl_ctx;
4765 struct xhci_slot_ctx *slot_ctx;
4766 unsigned long flags;
4767 unsigned think_time;
4768 int ret;
4769
4770 /* Ignore root hubs */
4771 if (!hdev->parent)
4772 return 0;
4773
4774 vdev = xhci->devs[hdev->slot_id];
4775 if (!vdev) {
4776 xhci_warn(xhci, "Cannot update hub desc for unknown device.\n");
4777 return -EINVAL;
4778 }
4779 config_cmd = xhci_alloc_command(xhci, true, true, mem_flags);
4780 if (!config_cmd) {
4781 xhci_dbg(xhci, "Could not allocate xHCI command structure.\n");
4782 return -ENOMEM;
4783 }
4784 ctrl_ctx = xhci_get_input_control_ctx(config_cmd->in_ctx);
4785 if (!ctrl_ctx) {
4786 xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
4787 __func__);
4788 xhci_free_command(xhci, config_cmd);
4789 return -ENOMEM;
4790 }
4791
4792 spin_lock_irqsave(&xhci->lock, flags);
4793 if (hdev->speed == USB_SPEED_HIGH &&
4794 xhci_alloc_tt_info(xhci, vdev, hdev, tt, GFP_ATOMIC)) {
4795 xhci_dbg(xhci, "Could not allocate xHCI TT structure.\n");
4796 xhci_free_command(xhci, config_cmd);
4797 spin_unlock_irqrestore(&xhci->lock, flags);
4798 return -ENOMEM;
4799 }
4800
4801 xhci_slot_copy(xhci, config_cmd->in_ctx, vdev->out_ctx);
4802 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
4803 slot_ctx = xhci_get_slot_ctx(xhci, config_cmd->in_ctx);
4804 slot_ctx->dev_info |= cpu_to_le32(DEV_HUB);
4805 /*
4806 * refer to section 6.2.2: MTT should be 0 for full speed hub,
4807 * but it may be already set to 1 when setup an xHCI virtual
4808 * device, so clear it anyway.
4809 */
4810 if (tt->multi)
4811 slot_ctx->dev_info |= cpu_to_le32(DEV_MTT);
4812 else if (hdev->speed == USB_SPEED_FULL)
4813 slot_ctx->dev_info &= cpu_to_le32(~DEV_MTT);
4814
4815 if (xhci->hci_version > 0x95) {
4816 xhci_dbg(xhci, "xHCI version %x needs hub "
4817 "TT think time and number of ports\n",
4818 (unsigned int) xhci->hci_version);
4819 slot_ctx->dev_info2 |= cpu_to_le32(XHCI_MAX_PORTS(hdev->maxchild));
4820 /* Set TT think time - convert from ns to FS bit times.
4821 * 0 = 8 FS bit times, 1 = 16 FS bit times,
4822 * 2 = 24 FS bit times, 3 = 32 FS bit times.
4823 *
4824 * xHCI 1.0: this field shall be 0 if the device is not a
4825 * High-spped hub.
4826 */
4827 think_time = tt->think_time;
4828 if (think_time != 0)
4829 think_time = (think_time / 666) - 1;
4830 if (xhci->hci_version < 0x100 || hdev->speed == USB_SPEED_HIGH)
4831 slot_ctx->tt_info |=
4832 cpu_to_le32(TT_THINK_TIME(think_time));
4833 } else {
4834 xhci_dbg(xhci, "xHCI version %x doesn't need hub "
4835 "TT think time or number of ports\n",
4836 (unsigned int) xhci->hci_version);
4837 }
4838 slot_ctx->dev_state = 0;
4839 spin_unlock_irqrestore(&xhci->lock, flags);
4840
4841 xhci_dbg(xhci, "Set up %s for hub device.\n",
4842 (xhci->hci_version > 0x95) ?
4843 "configure endpoint" : "evaluate context");
4844 xhci_dbg(xhci, "Slot %u Input Context:\n", hdev->slot_id);
4845 xhci_dbg_ctx(xhci, config_cmd->in_ctx, 0);
4846
4847 /* Issue and wait for the configure endpoint or
4848 * evaluate context command.
4849 */
4850 if (xhci->hci_version > 0x95)
4851 ret = xhci_configure_endpoint(xhci, hdev, config_cmd,
4852 false, false);
4853 else
4854 ret = xhci_configure_endpoint(xhci, hdev, config_cmd,
4855 true, false);
4856
4857 xhci_dbg(xhci, "Slot %u Output Context:\n", hdev->slot_id);
4858 xhci_dbg_ctx(xhci, vdev->out_ctx, 0);
4859
4860 xhci_free_command(xhci, config_cmd);
4861 return ret;
4862}
4863
4864int xhci_get_frame(struct usb_hcd *hcd)
4865{
4866 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4867 /* EHCI mods by the periodic size. Why? */
4868 return readl(&xhci->run_regs->microframe_index) >> 3;
4869}
4870
4871int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks)
4872{
4873 struct xhci_hcd *xhci;
4874 struct device *dev = hcd->self.controller;
4875 int retval;
4876
4877 /* Accept arbitrarily long scatter-gather lists */
4878 hcd->self.sg_tablesize = ~0;
4879
4880 /* support to build packet from discontinuous buffers */
4881 hcd->self.no_sg_constraint = 1;
4882
4883 /* XHCI controllers don't stop the ep queue on short packets :| */
4884 hcd->self.no_stop_on_short = 1;
4885
4886 xhci = hcd_to_xhci(hcd);
4887
4888 if (usb_hcd_is_primary_hcd(hcd)) {
4889 xhci->main_hcd = hcd;
4890 /* Mark the first roothub as being USB 2.0.
4891 * The xHCI driver will register the USB 3.0 roothub.
4892 */
4893 hcd->speed = HCD_USB2;
4894 hcd->self.root_hub->speed = USB_SPEED_HIGH;
4895 /*
4896 * USB 2.0 roothub under xHCI has an integrated TT,
4897 * (rate matching hub) as opposed to having an OHCI/UHCI
4898 * companion controller.
4899 */
4900 hcd->has_tt = 1;
4901 } else {
4902 if (xhci->sbrn == 0x31) {
4903 xhci_info(xhci, "Host supports USB 3.1 Enhanced SuperSpeed\n");
4904 hcd->speed = HCD_USB31;
4905 hcd->self.root_hub->speed = USB_SPEED_SUPER_PLUS;
4906 }
4907 /* xHCI private pointer was set in xhci_pci_probe for the second
4908 * registered roothub.
4909 */
4910 return 0;
4911 }
4912
4913 mutex_init(&xhci->mutex);
4914 xhci->cap_regs = hcd->regs;
4915 xhci->op_regs = hcd->regs +
4916 HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
4917 xhci->run_regs = hcd->regs +
4918 (readl(&xhci->cap_regs->run_regs_off) & RTSOFF_MASK);
4919 /* Cache read-only capability registers */
4920 xhci->hcs_params1 = readl(&xhci->cap_regs->hcs_params1);
4921 xhci->hcs_params2 = readl(&xhci->cap_regs->hcs_params2);
4922 xhci->hcs_params3 = readl(&xhci->cap_regs->hcs_params3);
4923 xhci->hcc_params = readl(&xhci->cap_regs->hc_capbase);
4924 xhci->hci_version = HC_VERSION(xhci->hcc_params);
4925 xhci->hcc_params = readl(&xhci->cap_regs->hcc_params);
4926 if (xhci->hci_version > 0x100)
4927 xhci->hcc_params2 = readl(&xhci->cap_regs->hcc_params2);
4928 xhci_print_registers(xhci);
4929
4930 xhci->quirks = quirks;
4931
4932 get_quirks(dev, xhci);
4933
4934 /* In xhci controllers which follow xhci 1.0 spec gives a spurious
4935 * success event after a short transfer. This quirk will ignore such
4936 * spurious event.
4937 */
4938 if (xhci->hci_version > 0x96)
4939 xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
4940
4941 /* Make sure the HC is halted. */
4942 retval = xhci_halt(xhci);
4943 if (retval)
4944 return retval;
4945
4946 xhci_dbg(xhci, "Resetting HCD\n");
4947 /* Reset the internal HC memory state and registers. */
4948 retval = xhci_reset(xhci);
4949 if (retval)
4950 return retval;
4951 xhci_dbg(xhci, "Reset complete\n");
4952
4953 /*
4954 * On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0)
4955 * of HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
4956 * address memory pointers actually. So, this driver clears the AC64
4957 * bit of xhci->hcc_params to call dma_set_coherent_mask(dev,
4958 * DMA_BIT_MASK(32)) in this xhci_gen_setup().
4959 */
4960 if (xhci->quirks & XHCI_NO_64BIT_SUPPORT)
4961 xhci->hcc_params &= ~BIT(0);
4962
4963 /* Set dma_mask and coherent_dma_mask to 64-bits,
4964 * if xHC supports 64-bit addressing */
4965 if (HCC_64BIT_ADDR(xhci->hcc_params) &&
4966 !dma_set_mask(dev, DMA_BIT_MASK(64))) {
4967 xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
4968 dma_set_coherent_mask(dev, DMA_BIT_MASK(64));
4969 } else {
4970 /*
4971 * This is to avoid error in cases where a 32-bit USB
4972 * controller is used on a 64-bit capable system.
4973 */
4974 retval = dma_set_mask(dev, DMA_BIT_MASK(32));
4975 if (retval)
4976 return retval;
4977 xhci_dbg(xhci, "Enabling 32-bit DMA addresses.\n");
4978 dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
4979 }
4980
4981 xhci_dbg(xhci, "Calling HCD init\n");
4982 /* Initialize HCD and host controller data structures. */
4983 retval = xhci_init(hcd);
4984 if (retval)
4985 return retval;
4986 xhci_dbg(xhci, "Called HCD init\n");
4987
4988 xhci_info(xhci, "hcc params 0x%08x hci version 0x%x quirks 0x%08x\n",
4989 xhci->hcc_params, xhci->hci_version, xhci->quirks);
4990
4991 return 0;
4992}
4993EXPORT_SYMBOL_GPL(xhci_gen_setup);
4994
4995static const struct hc_driver xhci_hc_driver = {
4996 .description = "xhci-hcd",
4997 .product_desc = "xHCI Host Controller",
4998 .hcd_priv_size = sizeof(struct xhci_hcd),
4999
5000 /*
5001 * generic hardware linkage
5002 */
5003 .irq = xhci_irq,
5004 .flags = HCD_MEMORY | HCD_USB3 | HCD_SHARED,
5005
5006 /*
5007 * basic lifecycle operations
5008 */
5009 .reset = NULL, /* set in xhci_init_driver() */
5010 .start = xhci_run,
5011 .stop = xhci_stop,
5012 .shutdown = xhci_shutdown,
5013
5014 /*
5015 * managing i/o requests and associated device resources
5016 */
5017 .urb_enqueue = xhci_urb_enqueue,
5018 .urb_dequeue = xhci_urb_dequeue,
5019 .alloc_dev = xhci_alloc_dev,
5020 .free_dev = xhci_free_dev,
5021 .alloc_streams = xhci_alloc_streams,
5022 .free_streams = xhci_free_streams,
5023 .add_endpoint = xhci_add_endpoint,
5024 .drop_endpoint = xhci_drop_endpoint,
5025 .endpoint_reset = xhci_endpoint_reset,
5026 .check_bandwidth = xhci_check_bandwidth,
5027 .reset_bandwidth = xhci_reset_bandwidth,
5028 .address_device = xhci_address_device,
5029 .enable_device = xhci_enable_device,
5030 .update_hub_device = xhci_update_hub_device,
5031 .reset_device = xhci_discover_or_reset_device,
5032
5033 /*
5034 * scheduling support
5035 */
5036 .get_frame_number = xhci_get_frame,
5037
5038 /*
5039 * root hub support
5040 */
5041 .hub_control = xhci_hub_control,
5042 .hub_status_data = xhci_hub_status_data,
5043 .bus_suspend = xhci_bus_suspend,
5044 .bus_resume = xhci_bus_resume,
5045
5046 /*
5047 * call back when device connected and addressed
5048 */
5049 .update_device = xhci_update_device,
5050 .set_usb2_hw_lpm = xhci_set_usb2_hardware_lpm,
5051 .enable_usb3_lpm_timeout = xhci_enable_usb3_lpm_timeout,
5052 .disable_usb3_lpm_timeout = xhci_disable_usb3_lpm_timeout,
5053 .find_raw_port_number = xhci_find_raw_port_number,
5054};
5055
5056void xhci_init_driver(struct hc_driver *drv,
5057 const struct xhci_driver_overrides *over)
5058{
5059 BUG_ON(!over);
5060
5061 /* Copy the generic table to drv then apply the overrides */
5062 *drv = xhci_hc_driver;
5063
5064 if (over) {
5065 drv->hcd_priv_size += over->extra_priv_size;
5066 if (over->reset)
5067 drv->reset = over->reset;
5068 if (over->start)
5069 drv->start = over->start;
5070 }
5071}
5072EXPORT_SYMBOL_GPL(xhci_init_driver);
5073
5074MODULE_DESCRIPTION(DRIVER_DESC);
5075MODULE_AUTHOR(DRIVER_AUTHOR);
5076MODULE_LICENSE("GPL");
5077
5078static int __init xhci_hcd_init(void)
5079{
5080 /*
5081 * Check the compiler generated sizes of structures that must be laid
5082 * out in specific ways for hardware access.
5083 */
5084 BUILD_BUG_ON(sizeof(struct xhci_doorbell_array) != 256*32/8);
5085 BUILD_BUG_ON(sizeof(struct xhci_slot_ctx) != 8*32/8);
5086 BUILD_BUG_ON(sizeof(struct xhci_ep_ctx) != 8*32/8);
5087 /* xhci_device_control has eight fields, and also
5088 * embeds one xhci_slot_ctx and 31 xhci_ep_ctx
5089 */
5090 BUILD_BUG_ON(sizeof(struct xhci_stream_ctx) != 4*32/8);
5091 BUILD_BUG_ON(sizeof(union xhci_trb) != 4*32/8);
5092 BUILD_BUG_ON(sizeof(struct xhci_erst_entry) != 4*32/8);
5093 BUILD_BUG_ON(sizeof(struct xhci_cap_regs) != 8*32/8);
5094 BUILD_BUG_ON(sizeof(struct xhci_intr_reg) != 8*32/8);
5095 /* xhci_run_regs has eight fields and embeds 128 xhci_intr_regs */
5096 BUILD_BUG_ON(sizeof(struct xhci_run_regs) != (8+8*128)*32/8);
5097
5098 if (usb_disabled())
5099 return -ENODEV;
5100
5101 return 0;
5102}
5103
5104/*
5105 * If an init function is provided, an exit function must also be provided
5106 * to allow module unload.
5107 */
5108static void __exit xhci_hcd_fini(void) { }
5109
5110module_init(xhci_hcd_init);
5111module_exit(xhci_hcd_fini);
1/*
2 * xHCI host controller driver
3 *
4 * Copyright (C) 2008 Intel Corp.
5 *
6 * Author: Sarah Sharp
7 * Some code borrowed from the Linux EHCI driver.
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
12 *
13 * This program is distributed in the hope that it will be useful, but
14 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
15 * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
16 * for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software Foundation,
20 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21 */
22
23#include <linux/pci.h>
24#include <linux/irq.h>
25#include <linux/log2.h>
26#include <linux/module.h>
27#include <linux/moduleparam.h>
28#include <linux/slab.h>
29#include <linux/dmi.h>
30
31#include "xhci.h"
32
33#define DRIVER_AUTHOR "Sarah Sharp"
34#define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
35
36/* Some 0.95 hardware can't handle the chain bit on a Link TRB being cleared */
37static int link_quirk;
38module_param(link_quirk, int, S_IRUGO | S_IWUSR);
39MODULE_PARM_DESC(link_quirk, "Don't clear the chain bit on a link TRB");
40
41/* TODO: copied from ehci-hcd.c - can this be refactored? */
42/*
43 * handshake - spin reading hc until handshake completes or fails
44 * @ptr: address of hc register to be read
45 * @mask: bits to look at in result of read
46 * @done: value of those bits when handshake succeeds
47 * @usec: timeout in microseconds
48 *
49 * Returns negative errno, or zero on success
50 *
51 * Success happens when the "mask" bits have the specified value (hardware
52 * handshake done). There are two failure modes: "usec" have passed (major
53 * hardware flakeout), or the register reads as all-ones (hardware removed).
54 */
55int handshake(struct xhci_hcd *xhci, void __iomem *ptr,
56 u32 mask, u32 done, int usec)
57{
58 u32 result;
59
60 do {
61 result = xhci_readl(xhci, ptr);
62 if (result == ~(u32)0) /* card removed */
63 return -ENODEV;
64 result &= mask;
65 if (result == done)
66 return 0;
67 udelay(1);
68 usec--;
69 } while (usec > 0);
70 return -ETIMEDOUT;
71}
72
73/*
74 * Disable interrupts and begin the xHCI halting process.
75 */
76void xhci_quiesce(struct xhci_hcd *xhci)
77{
78 u32 halted;
79 u32 cmd;
80 u32 mask;
81
82 mask = ~(XHCI_IRQS);
83 halted = xhci_readl(xhci, &xhci->op_regs->status) & STS_HALT;
84 if (!halted)
85 mask &= ~CMD_RUN;
86
87 cmd = xhci_readl(xhci, &xhci->op_regs->command);
88 cmd &= mask;
89 xhci_writel(xhci, cmd, &xhci->op_regs->command);
90}
91
92/*
93 * Force HC into halt state.
94 *
95 * Disable any IRQs and clear the run/stop bit.
96 * HC will complete any current and actively pipelined transactions, and
97 * should halt within 16 ms of the run/stop bit being cleared.
98 * Read HC Halted bit in the status register to see when the HC is finished.
99 */
100int xhci_halt(struct xhci_hcd *xhci)
101{
102 int ret;
103 xhci_dbg(xhci, "// Halt the HC\n");
104 xhci_quiesce(xhci);
105
106 ret = handshake(xhci, &xhci->op_regs->status,
107 STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC);
108 if (!ret) {
109 xhci->xhc_state |= XHCI_STATE_HALTED;
110 xhci->cmd_ring_state = CMD_RING_STATE_STOPPED;
111 } else
112 xhci_warn(xhci, "Host not halted after %u microseconds.\n",
113 XHCI_MAX_HALT_USEC);
114 return ret;
115}
116
117/*
118 * Set the run bit and wait for the host to be running.
119 */
120static int xhci_start(struct xhci_hcd *xhci)
121{
122 u32 temp;
123 int ret;
124
125 temp = xhci_readl(xhci, &xhci->op_regs->command);
126 temp |= (CMD_RUN);
127 xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n",
128 temp);
129 xhci_writel(xhci, temp, &xhci->op_regs->command);
130
131 /*
132 * Wait for the HCHalted Status bit to be 0 to indicate the host is
133 * running.
134 */
135 ret = handshake(xhci, &xhci->op_regs->status,
136 STS_HALT, 0, XHCI_MAX_HALT_USEC);
137 if (ret == -ETIMEDOUT)
138 xhci_err(xhci, "Host took too long to start, "
139 "waited %u microseconds.\n",
140 XHCI_MAX_HALT_USEC);
141 if (!ret)
142 xhci->xhc_state &= ~XHCI_STATE_HALTED;
143 return ret;
144}
145
146/*
147 * Reset a halted HC.
148 *
149 * This resets pipelines, timers, counters, state machines, etc.
150 * Transactions will be terminated immediately, and operational registers
151 * will be set to their defaults.
152 */
153int xhci_reset(struct xhci_hcd *xhci)
154{
155 u32 command;
156 u32 state;
157 int ret, i;
158
159 state = xhci_readl(xhci, &xhci->op_regs->status);
160 if ((state & STS_HALT) == 0) {
161 xhci_warn(xhci, "Host controller not halted, aborting reset.\n");
162 return 0;
163 }
164
165 xhci_dbg(xhci, "// Reset the HC\n");
166 command = xhci_readl(xhci, &xhci->op_regs->command);
167 command |= CMD_RESET;
168 xhci_writel(xhci, command, &xhci->op_regs->command);
169
170 ret = handshake(xhci, &xhci->op_regs->command,
171 CMD_RESET, 0, 10 * 1000 * 1000);
172 if (ret)
173 return ret;
174
175 xhci_dbg(xhci, "Wait for controller to be ready for doorbell rings\n");
176 /*
177 * xHCI cannot write to any doorbells or operational registers other
178 * than status until the "Controller Not Ready" flag is cleared.
179 */
180 ret = handshake(xhci, &xhci->op_regs->status,
181 STS_CNR, 0, 10 * 1000 * 1000);
182
183 for (i = 0; i < 2; ++i) {
184 xhci->bus_state[i].port_c_suspend = 0;
185 xhci->bus_state[i].suspended_ports = 0;
186 xhci->bus_state[i].resuming_ports = 0;
187 }
188
189 return ret;
190}
191
192#ifdef CONFIG_PCI
193static int xhci_free_msi(struct xhci_hcd *xhci)
194{
195 int i;
196
197 if (!xhci->msix_entries)
198 return -EINVAL;
199
200 for (i = 0; i < xhci->msix_count; i++)
201 if (xhci->msix_entries[i].vector)
202 free_irq(xhci->msix_entries[i].vector,
203 xhci_to_hcd(xhci));
204 return 0;
205}
206
207/*
208 * Set up MSI
209 */
210static int xhci_setup_msi(struct xhci_hcd *xhci)
211{
212 int ret;
213 struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
214
215 ret = pci_enable_msi(pdev);
216 if (ret) {
217 xhci_dbg(xhci, "failed to allocate MSI entry\n");
218 return ret;
219 }
220
221 ret = request_irq(pdev->irq, (irq_handler_t)xhci_msi_irq,
222 0, "xhci_hcd", xhci_to_hcd(xhci));
223 if (ret) {
224 xhci_dbg(xhci, "disable MSI interrupt\n");
225 pci_disable_msi(pdev);
226 }
227
228 return ret;
229}
230
231/*
232 * Free IRQs
233 * free all IRQs request
234 */
235static void xhci_free_irq(struct xhci_hcd *xhci)
236{
237 struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
238 int ret;
239
240 /* return if using legacy interrupt */
241 if (xhci_to_hcd(xhci)->irq > 0)
242 return;
243
244 ret = xhci_free_msi(xhci);
245 if (!ret)
246 return;
247 if (pdev->irq > 0)
248 free_irq(pdev->irq, xhci_to_hcd(xhci));
249
250 return;
251}
252
253/*
254 * Set up MSI-X
255 */
256static int xhci_setup_msix(struct xhci_hcd *xhci)
257{
258 int i, ret = 0;
259 struct usb_hcd *hcd = xhci_to_hcd(xhci);
260 struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
261
262 /*
263 * calculate number of msi-x vectors supported.
264 * - HCS_MAX_INTRS: the max number of interrupts the host can handle,
265 * with max number of interrupters based on the xhci HCSPARAMS1.
266 * - num_online_cpus: maximum msi-x vectors per CPUs core.
267 * Add additional 1 vector to ensure always available interrupt.
268 */
269 xhci->msix_count = min(num_online_cpus() + 1,
270 HCS_MAX_INTRS(xhci->hcs_params1));
271
272 xhci->msix_entries =
273 kmalloc((sizeof(struct msix_entry))*xhci->msix_count,
274 GFP_KERNEL);
275 if (!xhci->msix_entries) {
276 xhci_err(xhci, "Failed to allocate MSI-X entries\n");
277 return -ENOMEM;
278 }
279
280 for (i = 0; i < xhci->msix_count; i++) {
281 xhci->msix_entries[i].entry = i;
282 xhci->msix_entries[i].vector = 0;
283 }
284
285 ret = pci_enable_msix(pdev, xhci->msix_entries, xhci->msix_count);
286 if (ret) {
287 xhci_dbg(xhci, "Failed to enable MSI-X\n");
288 goto free_entries;
289 }
290
291 for (i = 0; i < xhci->msix_count; i++) {
292 ret = request_irq(xhci->msix_entries[i].vector,
293 (irq_handler_t)xhci_msi_irq,
294 0, "xhci_hcd", xhci_to_hcd(xhci));
295 if (ret)
296 goto disable_msix;
297 }
298
299 hcd->msix_enabled = 1;
300 return ret;
301
302disable_msix:
303 xhci_dbg(xhci, "disable MSI-X interrupt\n");
304 xhci_free_irq(xhci);
305 pci_disable_msix(pdev);
306free_entries:
307 kfree(xhci->msix_entries);
308 xhci->msix_entries = NULL;
309 return ret;
310}
311
312/* Free any IRQs and disable MSI-X */
313static void xhci_cleanup_msix(struct xhci_hcd *xhci)
314{
315 struct usb_hcd *hcd = xhci_to_hcd(xhci);
316 struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
317
318 xhci_free_irq(xhci);
319
320 if (xhci->msix_entries) {
321 pci_disable_msix(pdev);
322 kfree(xhci->msix_entries);
323 xhci->msix_entries = NULL;
324 } else {
325 pci_disable_msi(pdev);
326 }
327
328 hcd->msix_enabled = 0;
329 return;
330}
331
332static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
333{
334 int i;
335
336 if (xhci->msix_entries) {
337 for (i = 0; i < xhci->msix_count; i++)
338 synchronize_irq(xhci->msix_entries[i].vector);
339 }
340}
341
342static int xhci_try_enable_msi(struct usb_hcd *hcd)
343{
344 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
345 struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
346 int ret;
347
348 /*
349 * Some Fresco Logic host controllers advertise MSI, but fail to
350 * generate interrupts. Don't even try to enable MSI.
351 */
352 if (xhci->quirks & XHCI_BROKEN_MSI)
353 return 0;
354
355 /* unregister the legacy interrupt */
356 if (hcd->irq)
357 free_irq(hcd->irq, hcd);
358 hcd->irq = 0;
359
360 ret = xhci_setup_msix(xhci);
361 if (ret)
362 /* fall back to msi*/
363 ret = xhci_setup_msi(xhci);
364
365 if (!ret)
366 /* hcd->irq is 0, we have MSI */
367 return 0;
368
369 if (!pdev->irq) {
370 xhci_err(xhci, "No msi-x/msi found and no IRQ in BIOS\n");
371 return -EINVAL;
372 }
373
374 /* fall back to legacy interrupt*/
375 ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED,
376 hcd->irq_descr, hcd);
377 if (ret) {
378 xhci_err(xhci, "request interrupt %d failed\n",
379 pdev->irq);
380 return ret;
381 }
382 hcd->irq = pdev->irq;
383 return 0;
384}
385
386#else
387
388static int xhci_try_enable_msi(struct usb_hcd *hcd)
389{
390 return 0;
391}
392
393static void xhci_cleanup_msix(struct xhci_hcd *xhci)
394{
395}
396
397static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
398{
399}
400
401#endif
402
403static void compliance_mode_recovery(unsigned long arg)
404{
405 struct xhci_hcd *xhci;
406 struct usb_hcd *hcd;
407 u32 temp;
408 int i;
409
410 xhci = (struct xhci_hcd *)arg;
411
412 for (i = 0; i < xhci->num_usb3_ports; i++) {
413 temp = xhci_readl(xhci, xhci->usb3_ports[i]);
414 if ((temp & PORT_PLS_MASK) == USB_SS_PORT_LS_COMP_MOD) {
415 /*
416 * Compliance Mode Detected. Letting USB Core
417 * handle the Warm Reset
418 */
419 xhci_dbg(xhci, "Compliance Mode Detected->Port %d!\n",
420 i + 1);
421 xhci_dbg(xhci, "Attempting Recovery routine!\n");
422 hcd = xhci->shared_hcd;
423
424 if (hcd->state == HC_STATE_SUSPENDED)
425 usb_hcd_resume_root_hub(hcd);
426
427 usb_hcd_poll_rh_status(hcd);
428 }
429 }
430
431 if (xhci->port_status_u0 != ((1 << xhci->num_usb3_ports)-1))
432 mod_timer(&xhci->comp_mode_recovery_timer,
433 jiffies + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
434}
435
436/*
437 * Quirk to work around issue generated by the SN65LVPE502CP USB3.0 re-driver
438 * that causes ports behind that hardware to enter compliance mode sometimes.
439 * The quirk creates a timer that polls every 2 seconds the link state of
440 * each host controller's port and recovers it by issuing a Warm reset
441 * if Compliance mode is detected, otherwise the port will become "dead" (no
442 * device connections or disconnections will be detected anymore). Becasue no
443 * status event is generated when entering compliance mode (per xhci spec),
444 * this quirk is needed on systems that have the failing hardware installed.
445 */
446static void compliance_mode_recovery_timer_init(struct xhci_hcd *xhci)
447{
448 xhci->port_status_u0 = 0;
449 init_timer(&xhci->comp_mode_recovery_timer);
450
451 xhci->comp_mode_recovery_timer.data = (unsigned long) xhci;
452 xhci->comp_mode_recovery_timer.function = compliance_mode_recovery;
453 xhci->comp_mode_recovery_timer.expires = jiffies +
454 msecs_to_jiffies(COMP_MODE_RCVRY_MSECS);
455
456 set_timer_slack(&xhci->comp_mode_recovery_timer,
457 msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
458 add_timer(&xhci->comp_mode_recovery_timer);
459 xhci_dbg(xhci, "Compliance Mode Recovery Timer Initialized.\n");
460}
461
462/*
463 * This function identifies the systems that have installed the SN65LVPE502CP
464 * USB3.0 re-driver and that need the Compliance Mode Quirk.
465 * Systems:
466 * Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820
467 */
468static bool compliance_mode_recovery_timer_quirk_check(void)
469{
470 const char *dmi_product_name, *dmi_sys_vendor;
471
472 dmi_product_name = dmi_get_system_info(DMI_PRODUCT_NAME);
473 dmi_sys_vendor = dmi_get_system_info(DMI_SYS_VENDOR);
474 if (!dmi_product_name || !dmi_sys_vendor)
475 return false;
476
477 if (!(strstr(dmi_sys_vendor, "Hewlett-Packard")))
478 return false;
479
480 if (strstr(dmi_product_name, "Z420") ||
481 strstr(dmi_product_name, "Z620") ||
482 strstr(dmi_product_name, "Z820"))
483 return true;
484
485 return false;
486}
487
488static int xhci_all_ports_seen_u0(struct xhci_hcd *xhci)
489{
490 return (xhci->port_status_u0 == ((1 << xhci->num_usb3_ports)-1));
491}
492
493
494/*
495 * Initialize memory for HCD and xHC (one-time init).
496 *
497 * Program the PAGESIZE register, initialize the device context array, create
498 * device contexts (?), set up a command ring segment (or two?), create event
499 * ring (one for now).
500 */
501int xhci_init(struct usb_hcd *hcd)
502{
503 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
504 int retval = 0;
505
506 xhci_dbg(xhci, "xhci_init\n");
507 spin_lock_init(&xhci->lock);
508 if (xhci->hci_version == 0x95 && link_quirk) {
509 xhci_dbg(xhci, "QUIRK: Not clearing Link TRB chain bits.\n");
510 xhci->quirks |= XHCI_LINK_TRB_QUIRK;
511 } else {
512 xhci_dbg(xhci, "xHCI doesn't need link TRB QUIRK\n");
513 }
514 retval = xhci_mem_init(xhci, GFP_KERNEL);
515 xhci_dbg(xhci, "Finished xhci_init\n");
516
517 /* Initializing Compliance Mode Recovery Data If Needed */
518 if (compliance_mode_recovery_timer_quirk_check()) {
519 xhci->quirks |= XHCI_COMP_MODE_QUIRK;
520 compliance_mode_recovery_timer_init(xhci);
521 }
522
523 return retval;
524}
525
526/*-------------------------------------------------------------------------*/
527
528
529#ifdef CONFIG_USB_XHCI_HCD_DEBUGGING
530static void xhci_event_ring_work(unsigned long arg)
531{
532 unsigned long flags;
533 int temp;
534 u64 temp_64;
535 struct xhci_hcd *xhci = (struct xhci_hcd *) arg;
536 int i, j;
537
538 xhci_dbg(xhci, "Poll event ring: %lu\n", jiffies);
539
540 spin_lock_irqsave(&xhci->lock, flags);
541 temp = xhci_readl(xhci, &xhci->op_regs->status);
542 xhci_dbg(xhci, "op reg status = 0x%x\n", temp);
543 if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING) ||
544 (xhci->xhc_state & XHCI_STATE_HALTED)) {
545 xhci_dbg(xhci, "HW died, polling stopped.\n");
546 spin_unlock_irqrestore(&xhci->lock, flags);
547 return;
548 }
549
550 temp = xhci_readl(xhci, &xhci->ir_set->irq_pending);
551 xhci_dbg(xhci, "ir_set 0 pending = 0x%x\n", temp);
552 xhci_dbg(xhci, "HC error bitmask = 0x%x\n", xhci->error_bitmask);
553 xhci->error_bitmask = 0;
554 xhci_dbg(xhci, "Event ring:\n");
555 xhci_debug_segment(xhci, xhci->event_ring->deq_seg);
556 xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
557 temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
558 temp_64 &= ~ERST_PTR_MASK;
559 xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64);
560 xhci_dbg(xhci, "Command ring:\n");
561 xhci_debug_segment(xhci, xhci->cmd_ring->deq_seg);
562 xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
563 xhci_dbg_cmd_ptrs(xhci);
564 for (i = 0; i < MAX_HC_SLOTS; ++i) {
565 if (!xhci->devs[i])
566 continue;
567 for (j = 0; j < 31; ++j) {
568 xhci_dbg_ep_rings(xhci, i, j, &xhci->devs[i]->eps[j]);
569 }
570 }
571 spin_unlock_irqrestore(&xhci->lock, flags);
572
573 if (!xhci->zombie)
574 mod_timer(&xhci->event_ring_timer, jiffies + POLL_TIMEOUT * HZ);
575 else
576 xhci_dbg(xhci, "Quit polling the event ring.\n");
577}
578#endif
579
580static int xhci_run_finished(struct xhci_hcd *xhci)
581{
582 if (xhci_start(xhci)) {
583 xhci_halt(xhci);
584 return -ENODEV;
585 }
586 xhci->shared_hcd->state = HC_STATE_RUNNING;
587 xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
588
589 if (xhci->quirks & XHCI_NEC_HOST)
590 xhci_ring_cmd_db(xhci);
591
592 xhci_dbg(xhci, "Finished xhci_run for USB3 roothub\n");
593 return 0;
594}
595
596/*
597 * Start the HC after it was halted.
598 *
599 * This function is called by the USB core when the HC driver is added.
600 * Its opposite is xhci_stop().
601 *
602 * xhci_init() must be called once before this function can be called.
603 * Reset the HC, enable device slot contexts, program DCBAAP, and
604 * set command ring pointer and event ring pointer.
605 *
606 * Setup MSI-X vectors and enable interrupts.
607 */
608int xhci_run(struct usb_hcd *hcd)
609{
610 u32 temp;
611 u64 temp_64;
612 int ret;
613 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
614
615 /* Start the xHCI host controller running only after the USB 2.0 roothub
616 * is setup.
617 */
618
619 hcd->uses_new_polling = 1;
620 if (!usb_hcd_is_primary_hcd(hcd))
621 return xhci_run_finished(xhci);
622
623 xhci_dbg(xhci, "xhci_run\n");
624
625 ret = xhci_try_enable_msi(hcd);
626 if (ret)
627 return ret;
628
629#ifdef CONFIG_USB_XHCI_HCD_DEBUGGING
630 init_timer(&xhci->event_ring_timer);
631 xhci->event_ring_timer.data = (unsigned long) xhci;
632 xhci->event_ring_timer.function = xhci_event_ring_work;
633 /* Poll the event ring */
634 xhci->event_ring_timer.expires = jiffies + POLL_TIMEOUT * HZ;
635 xhci->zombie = 0;
636 xhci_dbg(xhci, "Setting event ring polling timer\n");
637 add_timer(&xhci->event_ring_timer);
638#endif
639
640 xhci_dbg(xhci, "Command ring memory map follows:\n");
641 xhci_debug_ring(xhci, xhci->cmd_ring);
642 xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
643 xhci_dbg_cmd_ptrs(xhci);
644
645 xhci_dbg(xhci, "ERST memory map follows:\n");
646 xhci_dbg_erst(xhci, &xhci->erst);
647 xhci_dbg(xhci, "Event ring:\n");
648 xhci_debug_ring(xhci, xhci->event_ring);
649 xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
650 temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
651 temp_64 &= ~ERST_PTR_MASK;
652 xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64);
653
654 xhci_dbg(xhci, "// Set the interrupt modulation register\n");
655 temp = xhci_readl(xhci, &xhci->ir_set->irq_control);
656 temp &= ~ER_IRQ_INTERVAL_MASK;
657 temp |= (u32) 160;
658 xhci_writel(xhci, temp, &xhci->ir_set->irq_control);
659
660 /* Set the HCD state before we enable the irqs */
661 temp = xhci_readl(xhci, &xhci->op_regs->command);
662 temp |= (CMD_EIE);
663 xhci_dbg(xhci, "// Enable interrupts, cmd = 0x%x.\n",
664 temp);
665 xhci_writel(xhci, temp, &xhci->op_regs->command);
666
667 temp = xhci_readl(xhci, &xhci->ir_set->irq_pending);
668 xhci_dbg(xhci, "// Enabling event ring interrupter %p by writing 0x%x to irq_pending\n",
669 xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
670 xhci_writel(xhci, ER_IRQ_ENABLE(temp),
671 &xhci->ir_set->irq_pending);
672 xhci_print_ir_set(xhci, 0);
673
674 if (xhci->quirks & XHCI_NEC_HOST)
675 xhci_queue_vendor_command(xhci, 0, 0, 0,
676 TRB_TYPE(TRB_NEC_GET_FW));
677
678 xhci_dbg(xhci, "Finished xhci_run for USB2 roothub\n");
679 return 0;
680}
681
682static void xhci_only_stop_hcd(struct usb_hcd *hcd)
683{
684 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
685
686 spin_lock_irq(&xhci->lock);
687 xhci_halt(xhci);
688
689 /* The shared_hcd is going to be deallocated shortly (the USB core only
690 * calls this function when allocation fails in usb_add_hcd(), or
691 * usb_remove_hcd() is called). So we need to unset xHCI's pointer.
692 */
693 xhci->shared_hcd = NULL;
694 spin_unlock_irq(&xhci->lock);
695}
696
697/*
698 * Stop xHCI driver.
699 *
700 * This function is called by the USB core when the HC driver is removed.
701 * Its opposite is xhci_run().
702 *
703 * Disable device contexts, disable IRQs, and quiesce the HC.
704 * Reset the HC, finish any completed transactions, and cleanup memory.
705 */
706void xhci_stop(struct usb_hcd *hcd)
707{
708 u32 temp;
709 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
710
711 if (!usb_hcd_is_primary_hcd(hcd)) {
712 xhci_only_stop_hcd(xhci->shared_hcd);
713 return;
714 }
715
716 spin_lock_irq(&xhci->lock);
717 /* Make sure the xHC is halted for a USB3 roothub
718 * (xhci_stop() could be called as part of failed init).
719 */
720 xhci_halt(xhci);
721 xhci_reset(xhci);
722 spin_unlock_irq(&xhci->lock);
723
724 xhci_cleanup_msix(xhci);
725
726#ifdef CONFIG_USB_XHCI_HCD_DEBUGGING
727 /* Tell the event ring poll function not to reschedule */
728 xhci->zombie = 1;
729 del_timer_sync(&xhci->event_ring_timer);
730#endif
731
732 /* Deleting Compliance Mode Recovery Timer */
733 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
734 (!(xhci_all_ports_seen_u0(xhci))))
735 del_timer_sync(&xhci->comp_mode_recovery_timer);
736
737 if (xhci->quirks & XHCI_AMD_PLL_FIX)
738 usb_amd_dev_put();
739
740 xhci_dbg(xhci, "// Disabling event ring interrupts\n");
741 temp = xhci_readl(xhci, &xhci->op_regs->status);
742 xhci_writel(xhci, temp & ~STS_EINT, &xhci->op_regs->status);
743 temp = xhci_readl(xhci, &xhci->ir_set->irq_pending);
744 xhci_writel(xhci, ER_IRQ_DISABLE(temp),
745 &xhci->ir_set->irq_pending);
746 xhci_print_ir_set(xhci, 0);
747
748 xhci_dbg(xhci, "cleaning up memory\n");
749 xhci_mem_cleanup(xhci);
750 xhci_dbg(xhci, "xhci_stop completed - status = %x\n",
751 xhci_readl(xhci, &xhci->op_regs->status));
752}
753
754/*
755 * Shutdown HC (not bus-specific)
756 *
757 * This is called when the machine is rebooting or halting. We assume that the
758 * machine will be powered off, and the HC's internal state will be reset.
759 * Don't bother to free memory.
760 *
761 * This will only ever be called with the main usb_hcd (the USB3 roothub).
762 */
763void xhci_shutdown(struct usb_hcd *hcd)
764{
765 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
766
767 if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
768 usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
769
770 spin_lock_irq(&xhci->lock);
771 xhci_halt(xhci);
772 spin_unlock_irq(&xhci->lock);
773
774 xhci_cleanup_msix(xhci);
775
776 xhci_dbg(xhci, "xhci_shutdown completed - status = %x\n",
777 xhci_readl(xhci, &xhci->op_regs->status));
778}
779
780#ifdef CONFIG_PM
781static void xhci_save_registers(struct xhci_hcd *xhci)
782{
783 xhci->s3.command = xhci_readl(xhci, &xhci->op_regs->command);
784 xhci->s3.dev_nt = xhci_readl(xhci, &xhci->op_regs->dev_notification);
785 xhci->s3.dcbaa_ptr = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
786 xhci->s3.config_reg = xhci_readl(xhci, &xhci->op_regs->config_reg);
787 xhci->s3.erst_size = xhci_readl(xhci, &xhci->ir_set->erst_size);
788 xhci->s3.erst_base = xhci_read_64(xhci, &xhci->ir_set->erst_base);
789 xhci->s3.erst_dequeue = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
790 xhci->s3.irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending);
791 xhci->s3.irq_control = xhci_readl(xhci, &xhci->ir_set->irq_control);
792}
793
794static void xhci_restore_registers(struct xhci_hcd *xhci)
795{
796 xhci_writel(xhci, xhci->s3.command, &xhci->op_regs->command);
797 xhci_writel(xhci, xhci->s3.dev_nt, &xhci->op_regs->dev_notification);
798 xhci_write_64(xhci, xhci->s3.dcbaa_ptr, &xhci->op_regs->dcbaa_ptr);
799 xhci_writel(xhci, xhci->s3.config_reg, &xhci->op_regs->config_reg);
800 xhci_writel(xhci, xhci->s3.erst_size, &xhci->ir_set->erst_size);
801 xhci_write_64(xhci, xhci->s3.erst_base, &xhci->ir_set->erst_base);
802 xhci_write_64(xhci, xhci->s3.erst_dequeue, &xhci->ir_set->erst_dequeue);
803 xhci_writel(xhci, xhci->s3.irq_pending, &xhci->ir_set->irq_pending);
804 xhci_writel(xhci, xhci->s3.irq_control, &xhci->ir_set->irq_control);
805}
806
807static void xhci_set_cmd_ring_deq(struct xhci_hcd *xhci)
808{
809 u64 val_64;
810
811 /* step 2: initialize command ring buffer */
812 val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring);
813 val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) |
814 (xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
815 xhci->cmd_ring->dequeue) &
816 (u64) ~CMD_RING_RSVD_BITS) |
817 xhci->cmd_ring->cycle_state;
818 xhci_dbg(xhci, "// Setting command ring address to 0x%llx\n",
819 (long unsigned long) val_64);
820 xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring);
821}
822
823/*
824 * The whole command ring must be cleared to zero when we suspend the host.
825 *
826 * The host doesn't save the command ring pointer in the suspend well, so we
827 * need to re-program it on resume. Unfortunately, the pointer must be 64-byte
828 * aligned, because of the reserved bits in the command ring dequeue pointer
829 * register. Therefore, we can't just set the dequeue pointer back in the
830 * middle of the ring (TRBs are 16-byte aligned).
831 */
832static void xhci_clear_command_ring(struct xhci_hcd *xhci)
833{
834 struct xhci_ring *ring;
835 struct xhci_segment *seg;
836
837 ring = xhci->cmd_ring;
838 seg = ring->deq_seg;
839 do {
840 memset(seg->trbs, 0,
841 sizeof(union xhci_trb) * (TRBS_PER_SEGMENT - 1));
842 seg->trbs[TRBS_PER_SEGMENT - 1].link.control &=
843 cpu_to_le32(~TRB_CYCLE);
844 seg = seg->next;
845 } while (seg != ring->deq_seg);
846
847 /* Reset the software enqueue and dequeue pointers */
848 ring->deq_seg = ring->first_seg;
849 ring->dequeue = ring->first_seg->trbs;
850 ring->enq_seg = ring->deq_seg;
851 ring->enqueue = ring->dequeue;
852
853 ring->num_trbs_free = ring->num_segs * (TRBS_PER_SEGMENT - 1) - 1;
854 /*
855 * Ring is now zeroed, so the HW should look for change of ownership
856 * when the cycle bit is set to 1.
857 */
858 ring->cycle_state = 1;
859
860 /*
861 * Reset the hardware dequeue pointer.
862 * Yes, this will need to be re-written after resume, but we're paranoid
863 * and want to make sure the hardware doesn't access bogus memory
864 * because, say, the BIOS or an SMI started the host without changing
865 * the command ring pointers.
866 */
867 xhci_set_cmd_ring_deq(xhci);
868}
869
870/*
871 * Stop HC (not bus-specific)
872 *
873 * This is called when the machine transition into S3/S4 mode.
874 *
875 */
876int xhci_suspend(struct xhci_hcd *xhci)
877{
878 int rc = 0;
879 struct usb_hcd *hcd = xhci_to_hcd(xhci);
880 u32 command;
881
882 spin_lock_irq(&xhci->lock);
883 clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
884 clear_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
885 /* step 1: stop endpoint */
886 /* skipped assuming that port suspend has done */
887
888 /* step 2: clear Run/Stop bit */
889 command = xhci_readl(xhci, &xhci->op_regs->command);
890 command &= ~CMD_RUN;
891 xhci_writel(xhci, command, &xhci->op_regs->command);
892 if (handshake(xhci, &xhci->op_regs->status,
893 STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC)) {
894 xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
895 spin_unlock_irq(&xhci->lock);
896 return -ETIMEDOUT;
897 }
898 xhci_clear_command_ring(xhci);
899
900 /* step 3: save registers */
901 xhci_save_registers(xhci);
902
903 /* step 4: set CSS flag */
904 command = xhci_readl(xhci, &xhci->op_regs->command);
905 command |= CMD_CSS;
906 xhci_writel(xhci, command, &xhci->op_regs->command);
907 if (handshake(xhci, &xhci->op_regs->status, STS_SAVE, 0, 10 * 1000)) {
908 xhci_warn(xhci, "WARN: xHC save state timeout\n");
909 spin_unlock_irq(&xhci->lock);
910 return -ETIMEDOUT;
911 }
912 spin_unlock_irq(&xhci->lock);
913
914 /*
915 * Deleting Compliance Mode Recovery Timer because the xHCI Host
916 * is about to be suspended.
917 */
918 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
919 (!(xhci_all_ports_seen_u0(xhci)))) {
920 del_timer_sync(&xhci->comp_mode_recovery_timer);
921 xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted!\n");
922 }
923
924 /* step 5: remove core well power */
925 /* synchronize irq when using MSI-X */
926 xhci_msix_sync_irqs(xhci);
927
928 return rc;
929}
930
931/*
932 * start xHC (not bus-specific)
933 *
934 * This is called when the machine transition from S3/S4 mode.
935 *
936 */
937int xhci_resume(struct xhci_hcd *xhci, bool hibernated)
938{
939 u32 command, temp = 0;
940 struct usb_hcd *hcd = xhci_to_hcd(xhci);
941 struct usb_hcd *secondary_hcd;
942 int retval = 0;
943
944 /* Wait a bit if either of the roothubs need to settle from the
945 * transition into bus suspend.
946 */
947 if (time_before(jiffies, xhci->bus_state[0].next_statechange) ||
948 time_before(jiffies,
949 xhci->bus_state[1].next_statechange))
950 msleep(100);
951
952 set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
953 set_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
954
955 spin_lock_irq(&xhci->lock);
956 if (xhci->quirks & XHCI_RESET_ON_RESUME)
957 hibernated = true;
958
959 if (!hibernated) {
960 /* step 1: restore register */
961 xhci_restore_registers(xhci);
962 /* step 2: initialize command ring buffer */
963 xhci_set_cmd_ring_deq(xhci);
964 /* step 3: restore state and start state*/
965 /* step 3: set CRS flag */
966 command = xhci_readl(xhci, &xhci->op_regs->command);
967 command |= CMD_CRS;
968 xhci_writel(xhci, command, &xhci->op_regs->command);
969 if (handshake(xhci, &xhci->op_regs->status,
970 STS_RESTORE, 0, 10 * 1000)) {
971 xhci_warn(xhci, "WARN: xHC restore state timeout\n");
972 spin_unlock_irq(&xhci->lock);
973 return -ETIMEDOUT;
974 }
975 temp = xhci_readl(xhci, &xhci->op_regs->status);
976 }
977
978 /* If restore operation fails, re-initialize the HC during resume */
979 if ((temp & STS_SRE) || hibernated) {
980 /* Let the USB core know _both_ roothubs lost power. */
981 usb_root_hub_lost_power(xhci->main_hcd->self.root_hub);
982 usb_root_hub_lost_power(xhci->shared_hcd->self.root_hub);
983
984 xhci_dbg(xhci, "Stop HCD\n");
985 xhci_halt(xhci);
986 xhci_reset(xhci);
987 spin_unlock_irq(&xhci->lock);
988 xhci_cleanup_msix(xhci);
989
990#ifdef CONFIG_USB_XHCI_HCD_DEBUGGING
991 /* Tell the event ring poll function not to reschedule */
992 xhci->zombie = 1;
993 del_timer_sync(&xhci->event_ring_timer);
994#endif
995
996 xhci_dbg(xhci, "// Disabling event ring interrupts\n");
997 temp = xhci_readl(xhci, &xhci->op_regs->status);
998 xhci_writel(xhci, temp & ~STS_EINT, &xhci->op_regs->status);
999 temp = xhci_readl(xhci, &xhci->ir_set->irq_pending);
1000 xhci_writel(xhci, ER_IRQ_DISABLE(temp),
1001 &xhci->ir_set->irq_pending);
1002 xhci_print_ir_set(xhci, 0);
1003
1004 xhci_dbg(xhci, "cleaning up memory\n");
1005 xhci_mem_cleanup(xhci);
1006 xhci_dbg(xhci, "xhci_stop completed - status = %x\n",
1007 xhci_readl(xhci, &xhci->op_regs->status));
1008
1009 /* USB core calls the PCI reinit and start functions twice:
1010 * first with the primary HCD, and then with the secondary HCD.
1011 * If we don't do the same, the host will never be started.
1012 */
1013 if (!usb_hcd_is_primary_hcd(hcd))
1014 secondary_hcd = hcd;
1015 else
1016 secondary_hcd = xhci->shared_hcd;
1017
1018 xhci_dbg(xhci, "Initialize the xhci_hcd\n");
1019 retval = xhci_init(hcd->primary_hcd);
1020 if (retval)
1021 return retval;
1022 xhci_dbg(xhci, "Start the primary HCD\n");
1023 retval = xhci_run(hcd->primary_hcd);
1024 if (!retval) {
1025 xhci_dbg(xhci, "Start the secondary HCD\n");
1026 retval = xhci_run(secondary_hcd);
1027 }
1028 hcd->state = HC_STATE_SUSPENDED;
1029 xhci->shared_hcd->state = HC_STATE_SUSPENDED;
1030 goto done;
1031 }
1032
1033 /* step 4: set Run/Stop bit */
1034 command = xhci_readl(xhci, &xhci->op_regs->command);
1035 command |= CMD_RUN;
1036 xhci_writel(xhci, command, &xhci->op_regs->command);
1037 handshake(xhci, &xhci->op_regs->status, STS_HALT,
1038 0, 250 * 1000);
1039
1040 /* step 5: walk topology and initialize portsc,
1041 * portpmsc and portli
1042 */
1043 /* this is done in bus_resume */
1044
1045 /* step 6: restart each of the previously
1046 * Running endpoints by ringing their doorbells
1047 */
1048
1049 spin_unlock_irq(&xhci->lock);
1050
1051 done:
1052 if (retval == 0) {
1053 usb_hcd_resume_root_hub(hcd);
1054 usb_hcd_resume_root_hub(xhci->shared_hcd);
1055 }
1056
1057 /*
1058 * If system is subject to the Quirk, Compliance Mode Timer needs to
1059 * be re-initialized Always after a system resume. Ports are subject
1060 * to suffer the Compliance Mode issue again. It doesn't matter if
1061 * ports have entered previously to U0 before system's suspension.
1062 */
1063 if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
1064 compliance_mode_recovery_timer_init(xhci);
1065
1066 return retval;
1067}
1068#endif /* CONFIG_PM */
1069
1070/*-------------------------------------------------------------------------*/
1071
1072/**
1073 * xhci_get_endpoint_index - Used for passing endpoint bitmasks between the core and
1074 * HCDs. Find the index for an endpoint given its descriptor. Use the return
1075 * value to right shift 1 for the bitmask.
1076 *
1077 * Index = (epnum * 2) + direction - 1,
1078 * where direction = 0 for OUT, 1 for IN.
1079 * For control endpoints, the IN index is used (OUT index is unused), so
1080 * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2)
1081 */
1082unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc)
1083{
1084 unsigned int index;
1085 if (usb_endpoint_xfer_control(desc))
1086 index = (unsigned int) (usb_endpoint_num(desc)*2);
1087 else
1088 index = (unsigned int) (usb_endpoint_num(desc)*2) +
1089 (usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
1090 return index;
1091}
1092
1093/* Find the flag for this endpoint (for use in the control context). Use the
1094 * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
1095 * bit 1, etc.
1096 */
1097unsigned int xhci_get_endpoint_flag(struct usb_endpoint_descriptor *desc)
1098{
1099 return 1 << (xhci_get_endpoint_index(desc) + 1);
1100}
1101
1102/* Find the flag for this endpoint (for use in the control context). Use the
1103 * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
1104 * bit 1, etc.
1105 */
1106unsigned int xhci_get_endpoint_flag_from_index(unsigned int ep_index)
1107{
1108 return 1 << (ep_index + 1);
1109}
1110
1111/* Compute the last valid endpoint context index. Basically, this is the
1112 * endpoint index plus one. For slot contexts with more than valid endpoint,
1113 * we find the most significant bit set in the added contexts flags.
1114 * e.g. ep 1 IN (with epnum 0x81) => added_ctxs = 0b1000
1115 * fls(0b1000) = 4, but the endpoint context index is 3, so subtract one.
1116 */
1117unsigned int xhci_last_valid_endpoint(u32 added_ctxs)
1118{
1119 return fls(added_ctxs) - 1;
1120}
1121
1122/* Returns 1 if the arguments are OK;
1123 * returns 0 this is a root hub; returns -EINVAL for NULL pointers.
1124 */
1125static int xhci_check_args(struct usb_hcd *hcd, struct usb_device *udev,
1126 struct usb_host_endpoint *ep, int check_ep, bool check_virt_dev,
1127 const char *func) {
1128 struct xhci_hcd *xhci;
1129 struct xhci_virt_device *virt_dev;
1130
1131 if (!hcd || (check_ep && !ep) || !udev) {
1132 printk(KERN_DEBUG "xHCI %s called with invalid args\n",
1133 func);
1134 return -EINVAL;
1135 }
1136 if (!udev->parent) {
1137 printk(KERN_DEBUG "xHCI %s called for root hub\n",
1138 func);
1139 return 0;
1140 }
1141
1142 xhci = hcd_to_xhci(hcd);
1143 if (xhci->xhc_state & XHCI_STATE_HALTED)
1144 return -ENODEV;
1145
1146 if (check_virt_dev) {
1147 if (!udev->slot_id || !xhci->devs[udev->slot_id]) {
1148 printk(KERN_DEBUG "xHCI %s called with unaddressed "
1149 "device\n", func);
1150 return -EINVAL;
1151 }
1152
1153 virt_dev = xhci->devs[udev->slot_id];
1154 if (virt_dev->udev != udev) {
1155 printk(KERN_DEBUG "xHCI %s called with udev and "
1156 "virt_dev does not match\n", func);
1157 return -EINVAL;
1158 }
1159 }
1160
1161 return 1;
1162}
1163
1164static int xhci_configure_endpoint(struct xhci_hcd *xhci,
1165 struct usb_device *udev, struct xhci_command *command,
1166 bool ctx_change, bool must_succeed);
1167
1168/*
1169 * Full speed devices may have a max packet size greater than 8 bytes, but the
1170 * USB core doesn't know that until it reads the first 8 bytes of the
1171 * descriptor. If the usb_device's max packet size changes after that point,
1172 * we need to issue an evaluate context command and wait on it.
1173 */
1174static int xhci_check_maxpacket(struct xhci_hcd *xhci, unsigned int slot_id,
1175 unsigned int ep_index, struct urb *urb)
1176{
1177 struct xhci_container_ctx *in_ctx;
1178 struct xhci_container_ctx *out_ctx;
1179 struct xhci_input_control_ctx *ctrl_ctx;
1180 struct xhci_ep_ctx *ep_ctx;
1181 int max_packet_size;
1182 int hw_max_packet_size;
1183 int ret = 0;
1184
1185 out_ctx = xhci->devs[slot_id]->out_ctx;
1186 ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
1187 hw_max_packet_size = MAX_PACKET_DECODED(le32_to_cpu(ep_ctx->ep_info2));
1188 max_packet_size = usb_endpoint_maxp(&urb->dev->ep0.desc);
1189 if (hw_max_packet_size != max_packet_size) {
1190 xhci_dbg(xhci, "Max Packet Size for ep 0 changed.\n");
1191 xhci_dbg(xhci, "Max packet size in usb_device = %d\n",
1192 max_packet_size);
1193 xhci_dbg(xhci, "Max packet size in xHCI HW = %d\n",
1194 hw_max_packet_size);
1195 xhci_dbg(xhci, "Issuing evaluate context command.\n");
1196
1197 /* Set up the modified control endpoint 0 */
1198 xhci_endpoint_copy(xhci, xhci->devs[slot_id]->in_ctx,
1199 xhci->devs[slot_id]->out_ctx, ep_index);
1200 in_ctx = xhci->devs[slot_id]->in_ctx;
1201 ep_ctx = xhci_get_ep_ctx(xhci, in_ctx, ep_index);
1202 ep_ctx->ep_info2 &= cpu_to_le32(~MAX_PACKET_MASK);
1203 ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet_size));
1204
1205 /* Set up the input context flags for the command */
1206 /* FIXME: This won't work if a non-default control endpoint
1207 * changes max packet sizes.
1208 */
1209 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
1210 ctrl_ctx->add_flags = cpu_to_le32(EP0_FLAG);
1211 ctrl_ctx->drop_flags = 0;
1212
1213 xhci_dbg(xhci, "Slot %d input context\n", slot_id);
1214 xhci_dbg_ctx(xhci, in_ctx, ep_index);
1215 xhci_dbg(xhci, "Slot %d output context\n", slot_id);
1216 xhci_dbg_ctx(xhci, out_ctx, ep_index);
1217
1218 ret = xhci_configure_endpoint(xhci, urb->dev, NULL,
1219 true, false);
1220
1221 /* Clean up the input context for later use by bandwidth
1222 * functions.
1223 */
1224 ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG);
1225 }
1226 return ret;
1227}
1228
1229/*
1230 * non-error returns are a promise to giveback() the urb later
1231 * we drop ownership so next owner (or urb unlink) can get it
1232 */
1233int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags)
1234{
1235 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
1236 struct xhci_td *buffer;
1237 unsigned long flags;
1238 int ret = 0;
1239 unsigned int slot_id, ep_index;
1240 struct urb_priv *urb_priv;
1241 int size, i;
1242
1243 if (!urb || xhci_check_args(hcd, urb->dev, urb->ep,
1244 true, true, __func__) <= 0)
1245 return -EINVAL;
1246
1247 slot_id = urb->dev->slot_id;
1248 ep_index = xhci_get_endpoint_index(&urb->ep->desc);
1249
1250 if (!HCD_HW_ACCESSIBLE(hcd)) {
1251 if (!in_interrupt())
1252 xhci_dbg(xhci, "urb submitted during PCI suspend\n");
1253 ret = -ESHUTDOWN;
1254 goto exit;
1255 }
1256
1257 if (usb_endpoint_xfer_isoc(&urb->ep->desc))
1258 size = urb->number_of_packets;
1259 else
1260 size = 1;
1261
1262 urb_priv = kzalloc(sizeof(struct urb_priv) +
1263 size * sizeof(struct xhci_td *), mem_flags);
1264 if (!urb_priv)
1265 return -ENOMEM;
1266
1267 buffer = kzalloc(size * sizeof(struct xhci_td), mem_flags);
1268 if (!buffer) {
1269 kfree(urb_priv);
1270 return -ENOMEM;
1271 }
1272
1273 for (i = 0; i < size; i++) {
1274 urb_priv->td[i] = buffer;
1275 buffer++;
1276 }
1277
1278 urb_priv->length = size;
1279 urb_priv->td_cnt = 0;
1280 urb->hcpriv = urb_priv;
1281
1282 if (usb_endpoint_xfer_control(&urb->ep->desc)) {
1283 /* Check to see if the max packet size for the default control
1284 * endpoint changed during FS device enumeration
1285 */
1286 if (urb->dev->speed == USB_SPEED_FULL) {
1287 ret = xhci_check_maxpacket(xhci, slot_id,
1288 ep_index, urb);
1289 if (ret < 0) {
1290 xhci_urb_free_priv(xhci, urb_priv);
1291 urb->hcpriv = NULL;
1292 return ret;
1293 }
1294 }
1295
1296 /* We have a spinlock and interrupts disabled, so we must pass
1297 * atomic context to this function, which may allocate memory.
1298 */
1299 spin_lock_irqsave(&xhci->lock, flags);
1300 if (xhci->xhc_state & XHCI_STATE_DYING)
1301 goto dying;
1302 ret = xhci_queue_ctrl_tx(xhci, GFP_ATOMIC, urb,
1303 slot_id, ep_index);
1304 if (ret)
1305 goto free_priv;
1306 spin_unlock_irqrestore(&xhci->lock, flags);
1307 } else if (usb_endpoint_xfer_bulk(&urb->ep->desc)) {
1308 spin_lock_irqsave(&xhci->lock, flags);
1309 if (xhci->xhc_state & XHCI_STATE_DYING)
1310 goto dying;
1311 if (xhci->devs[slot_id]->eps[ep_index].ep_state &
1312 EP_GETTING_STREAMS) {
1313 xhci_warn(xhci, "WARN: Can't enqueue URB while bulk ep "
1314 "is transitioning to using streams.\n");
1315 ret = -EINVAL;
1316 } else if (xhci->devs[slot_id]->eps[ep_index].ep_state &
1317 EP_GETTING_NO_STREAMS) {
1318 xhci_warn(xhci, "WARN: Can't enqueue URB while bulk ep "
1319 "is transitioning to "
1320 "not having streams.\n");
1321 ret = -EINVAL;
1322 } else {
1323 ret = xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb,
1324 slot_id, ep_index);
1325 }
1326 if (ret)
1327 goto free_priv;
1328 spin_unlock_irqrestore(&xhci->lock, flags);
1329 } else if (usb_endpoint_xfer_int(&urb->ep->desc)) {
1330 spin_lock_irqsave(&xhci->lock, flags);
1331 if (xhci->xhc_state & XHCI_STATE_DYING)
1332 goto dying;
1333 ret = xhci_queue_intr_tx(xhci, GFP_ATOMIC, urb,
1334 slot_id, ep_index);
1335 if (ret)
1336 goto free_priv;
1337 spin_unlock_irqrestore(&xhci->lock, flags);
1338 } else {
1339 spin_lock_irqsave(&xhci->lock, flags);
1340 if (xhci->xhc_state & XHCI_STATE_DYING)
1341 goto dying;
1342 ret = xhci_queue_isoc_tx_prepare(xhci, GFP_ATOMIC, urb,
1343 slot_id, ep_index);
1344 if (ret)
1345 goto free_priv;
1346 spin_unlock_irqrestore(&xhci->lock, flags);
1347 }
1348exit:
1349 return ret;
1350dying:
1351 xhci_dbg(xhci, "Ep 0x%x: URB %p submitted for "
1352 "non-responsive xHCI host.\n",
1353 urb->ep->desc.bEndpointAddress, urb);
1354 ret = -ESHUTDOWN;
1355free_priv:
1356 xhci_urb_free_priv(xhci, urb_priv);
1357 urb->hcpriv = NULL;
1358 spin_unlock_irqrestore(&xhci->lock, flags);
1359 return ret;
1360}
1361
1362/* Get the right ring for the given URB.
1363 * If the endpoint supports streams, boundary check the URB's stream ID.
1364 * If the endpoint doesn't support streams, return the singular endpoint ring.
1365 */
1366static struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci,
1367 struct urb *urb)
1368{
1369 unsigned int slot_id;
1370 unsigned int ep_index;
1371 unsigned int stream_id;
1372 struct xhci_virt_ep *ep;
1373
1374 slot_id = urb->dev->slot_id;
1375 ep_index = xhci_get_endpoint_index(&urb->ep->desc);
1376 stream_id = urb->stream_id;
1377 ep = &xhci->devs[slot_id]->eps[ep_index];
1378 /* Common case: no streams */
1379 if (!(ep->ep_state & EP_HAS_STREAMS))
1380 return ep->ring;
1381
1382 if (stream_id == 0) {
1383 xhci_warn(xhci,
1384 "WARN: Slot ID %u, ep index %u has streams, "
1385 "but URB has no stream ID.\n",
1386 slot_id, ep_index);
1387 return NULL;
1388 }
1389
1390 if (stream_id < ep->stream_info->num_streams)
1391 return ep->stream_info->stream_rings[stream_id];
1392
1393 xhci_warn(xhci,
1394 "WARN: Slot ID %u, ep index %u has "
1395 "stream IDs 1 to %u allocated, "
1396 "but stream ID %u is requested.\n",
1397 slot_id, ep_index,
1398 ep->stream_info->num_streams - 1,
1399 stream_id);
1400 return NULL;
1401}
1402
1403/*
1404 * Remove the URB's TD from the endpoint ring. This may cause the HC to stop
1405 * USB transfers, potentially stopping in the middle of a TRB buffer. The HC
1406 * should pick up where it left off in the TD, unless a Set Transfer Ring
1407 * Dequeue Pointer is issued.
1408 *
1409 * The TRBs that make up the buffers for the canceled URB will be "removed" from
1410 * the ring. Since the ring is a contiguous structure, they can't be physically
1411 * removed. Instead, there are two options:
1412 *
1413 * 1) If the HC is in the middle of processing the URB to be canceled, we
1414 * simply move the ring's dequeue pointer past those TRBs using the Set
1415 * Transfer Ring Dequeue Pointer command. This will be the common case,
1416 * when drivers timeout on the last submitted URB and attempt to cancel.
1417 *
1418 * 2) If the HC is in the middle of a different TD, we turn the TRBs into a
1419 * series of 1-TRB transfer no-op TDs. (No-ops shouldn't be chained.) The
1420 * HC will need to invalidate the any TRBs it has cached after the stop
1421 * endpoint command, as noted in the xHCI 0.95 errata.
1422 *
1423 * 3) The TD may have completed by the time the Stop Endpoint Command
1424 * completes, so software needs to handle that case too.
1425 *
1426 * This function should protect against the TD enqueueing code ringing the
1427 * doorbell while this code is waiting for a Stop Endpoint command to complete.
1428 * It also needs to account for multiple cancellations on happening at the same
1429 * time for the same endpoint.
1430 *
1431 * Note that this function can be called in any context, or so says
1432 * usb_hcd_unlink_urb()
1433 */
1434int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
1435{
1436 unsigned long flags;
1437 int ret, i;
1438 u32 temp;
1439 struct xhci_hcd *xhci;
1440 struct urb_priv *urb_priv;
1441 struct xhci_td *td;
1442 unsigned int ep_index;
1443 struct xhci_ring *ep_ring;
1444 struct xhci_virt_ep *ep;
1445
1446 xhci = hcd_to_xhci(hcd);
1447 spin_lock_irqsave(&xhci->lock, flags);
1448 /* Make sure the URB hasn't completed or been unlinked already */
1449 ret = usb_hcd_check_unlink_urb(hcd, urb, status);
1450 if (ret || !urb->hcpriv)
1451 goto done;
1452 temp = xhci_readl(xhci, &xhci->op_regs->status);
1453 if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_HALTED)) {
1454 xhci_dbg(xhci, "HW died, freeing TD.\n");
1455 urb_priv = urb->hcpriv;
1456 for (i = urb_priv->td_cnt; i < urb_priv->length; i++) {
1457 td = urb_priv->td[i];
1458 if (!list_empty(&td->td_list))
1459 list_del_init(&td->td_list);
1460 if (!list_empty(&td->cancelled_td_list))
1461 list_del_init(&td->cancelled_td_list);
1462 }
1463
1464 usb_hcd_unlink_urb_from_ep(hcd, urb);
1465 spin_unlock_irqrestore(&xhci->lock, flags);
1466 usb_hcd_giveback_urb(hcd, urb, -ESHUTDOWN);
1467 xhci_urb_free_priv(xhci, urb_priv);
1468 return ret;
1469 }
1470 if ((xhci->xhc_state & XHCI_STATE_DYING) ||
1471 (xhci->xhc_state & XHCI_STATE_HALTED)) {
1472 xhci_dbg(xhci, "Ep 0x%x: URB %p to be canceled on "
1473 "non-responsive xHCI host.\n",
1474 urb->ep->desc.bEndpointAddress, urb);
1475 /* Let the stop endpoint command watchdog timer (which set this
1476 * state) finish cleaning up the endpoint TD lists. We must
1477 * have caught it in the middle of dropping a lock and giving
1478 * back an URB.
1479 */
1480 goto done;
1481 }
1482
1483 ep_index = xhci_get_endpoint_index(&urb->ep->desc);
1484 ep = &xhci->devs[urb->dev->slot_id]->eps[ep_index];
1485 ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
1486 if (!ep_ring) {
1487 ret = -EINVAL;
1488 goto done;
1489 }
1490
1491 urb_priv = urb->hcpriv;
1492 i = urb_priv->td_cnt;
1493 if (i < urb_priv->length)
1494 xhci_dbg(xhci, "Cancel URB %p, dev %s, ep 0x%x, "
1495 "starting at offset 0x%llx\n",
1496 urb, urb->dev->devpath,
1497 urb->ep->desc.bEndpointAddress,
1498 (unsigned long long) xhci_trb_virt_to_dma(
1499 urb_priv->td[i]->start_seg,
1500 urb_priv->td[i]->first_trb));
1501
1502 for (; i < urb_priv->length; i++) {
1503 td = urb_priv->td[i];
1504 list_add_tail(&td->cancelled_td_list, &ep->cancelled_td_list);
1505 }
1506
1507 /* Queue a stop endpoint command, but only if this is
1508 * the first cancellation to be handled.
1509 */
1510 if (!(ep->ep_state & EP_HALT_PENDING)) {
1511 ep->ep_state |= EP_HALT_PENDING;
1512 ep->stop_cmds_pending++;
1513 ep->stop_cmd_timer.expires = jiffies +
1514 XHCI_STOP_EP_CMD_TIMEOUT * HZ;
1515 add_timer(&ep->stop_cmd_timer);
1516 xhci_queue_stop_endpoint(xhci, urb->dev->slot_id, ep_index, 0);
1517 xhci_ring_cmd_db(xhci);
1518 }
1519done:
1520 spin_unlock_irqrestore(&xhci->lock, flags);
1521 return ret;
1522}
1523
1524/* Drop an endpoint from a new bandwidth configuration for this device.
1525 * Only one call to this function is allowed per endpoint before
1526 * check_bandwidth() or reset_bandwidth() must be called.
1527 * A call to xhci_drop_endpoint() followed by a call to xhci_add_endpoint() will
1528 * add the endpoint to the schedule with possibly new parameters denoted by a
1529 * different endpoint descriptor in usb_host_endpoint.
1530 * A call to xhci_add_endpoint() followed by a call to xhci_drop_endpoint() is
1531 * not allowed.
1532 *
1533 * The USB core will not allow URBs to be queued to an endpoint that is being
1534 * disabled, so there's no need for mutual exclusion to protect
1535 * the xhci->devs[slot_id] structure.
1536 */
1537int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
1538 struct usb_host_endpoint *ep)
1539{
1540 struct xhci_hcd *xhci;
1541 struct xhci_container_ctx *in_ctx, *out_ctx;
1542 struct xhci_input_control_ctx *ctrl_ctx;
1543 struct xhci_slot_ctx *slot_ctx;
1544 unsigned int last_ctx;
1545 unsigned int ep_index;
1546 struct xhci_ep_ctx *ep_ctx;
1547 u32 drop_flag;
1548 u32 new_add_flags, new_drop_flags, new_slot_info;
1549 int ret;
1550
1551 ret = xhci_check_args(hcd, udev, ep, 1, true, __func__);
1552 if (ret <= 0)
1553 return ret;
1554 xhci = hcd_to_xhci(hcd);
1555 if (xhci->xhc_state & XHCI_STATE_DYING)
1556 return -ENODEV;
1557
1558 xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev);
1559 drop_flag = xhci_get_endpoint_flag(&ep->desc);
1560 if (drop_flag == SLOT_FLAG || drop_flag == EP0_FLAG) {
1561 xhci_dbg(xhci, "xHCI %s - can't drop slot or ep 0 %#x\n",
1562 __func__, drop_flag);
1563 return 0;
1564 }
1565
1566 in_ctx = xhci->devs[udev->slot_id]->in_ctx;
1567 out_ctx = xhci->devs[udev->slot_id]->out_ctx;
1568 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
1569 ep_index = xhci_get_endpoint_index(&ep->desc);
1570 ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
1571 /* If the HC already knows the endpoint is disabled,
1572 * or the HCD has noted it is disabled, ignore this request
1573 */
1574 if (((ep_ctx->ep_info & cpu_to_le32(EP_STATE_MASK)) ==
1575 cpu_to_le32(EP_STATE_DISABLED)) ||
1576 le32_to_cpu(ctrl_ctx->drop_flags) &
1577 xhci_get_endpoint_flag(&ep->desc)) {
1578 xhci_warn(xhci, "xHCI %s called with disabled ep %p\n",
1579 __func__, ep);
1580 return 0;
1581 }
1582
1583 ctrl_ctx->drop_flags |= cpu_to_le32(drop_flag);
1584 new_drop_flags = le32_to_cpu(ctrl_ctx->drop_flags);
1585
1586 ctrl_ctx->add_flags &= cpu_to_le32(~drop_flag);
1587 new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
1588
1589 last_ctx = xhci_last_valid_endpoint(le32_to_cpu(ctrl_ctx->add_flags));
1590 slot_ctx = xhci_get_slot_ctx(xhci, in_ctx);
1591 /* Update the last valid endpoint context, if we deleted the last one */
1592 if ((le32_to_cpu(slot_ctx->dev_info) & LAST_CTX_MASK) >
1593 LAST_CTX(last_ctx)) {
1594 slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
1595 slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(last_ctx));
1596 }
1597 new_slot_info = le32_to_cpu(slot_ctx->dev_info);
1598
1599 xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
1600
1601 xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x, new slot info = %#x\n",
1602 (unsigned int) ep->desc.bEndpointAddress,
1603 udev->slot_id,
1604 (unsigned int) new_drop_flags,
1605 (unsigned int) new_add_flags,
1606 (unsigned int) new_slot_info);
1607 return 0;
1608}
1609
1610/* Add an endpoint to a new possible bandwidth configuration for this device.
1611 * Only one call to this function is allowed per endpoint before
1612 * check_bandwidth() or reset_bandwidth() must be called.
1613 * A call to xhci_drop_endpoint() followed by a call to xhci_add_endpoint() will
1614 * add the endpoint to the schedule with possibly new parameters denoted by a
1615 * different endpoint descriptor in usb_host_endpoint.
1616 * A call to xhci_add_endpoint() followed by a call to xhci_drop_endpoint() is
1617 * not allowed.
1618 *
1619 * The USB core will not allow URBs to be queued to an endpoint until the
1620 * configuration or alt setting is installed in the device, so there's no need
1621 * for mutual exclusion to protect the xhci->devs[slot_id] structure.
1622 */
1623int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
1624 struct usb_host_endpoint *ep)
1625{
1626 struct xhci_hcd *xhci;
1627 struct xhci_container_ctx *in_ctx, *out_ctx;
1628 unsigned int ep_index;
1629 struct xhci_ep_ctx *ep_ctx;
1630 struct xhci_slot_ctx *slot_ctx;
1631 struct xhci_input_control_ctx *ctrl_ctx;
1632 u32 added_ctxs;
1633 unsigned int last_ctx;
1634 u32 new_add_flags, new_drop_flags, new_slot_info;
1635 struct xhci_virt_device *virt_dev;
1636 int ret = 0;
1637
1638 ret = xhci_check_args(hcd, udev, ep, 1, true, __func__);
1639 if (ret <= 0) {
1640 /* So we won't queue a reset ep command for a root hub */
1641 ep->hcpriv = NULL;
1642 return ret;
1643 }
1644 xhci = hcd_to_xhci(hcd);
1645 if (xhci->xhc_state & XHCI_STATE_DYING)
1646 return -ENODEV;
1647
1648 added_ctxs = xhci_get_endpoint_flag(&ep->desc);
1649 last_ctx = xhci_last_valid_endpoint(added_ctxs);
1650 if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) {
1651 /* FIXME when we have to issue an evaluate endpoint command to
1652 * deal with ep0 max packet size changing once we get the
1653 * descriptors
1654 */
1655 xhci_dbg(xhci, "xHCI %s - can't add slot or ep 0 %#x\n",
1656 __func__, added_ctxs);
1657 return 0;
1658 }
1659
1660 virt_dev = xhci->devs[udev->slot_id];
1661 in_ctx = virt_dev->in_ctx;
1662 out_ctx = virt_dev->out_ctx;
1663 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
1664 ep_index = xhci_get_endpoint_index(&ep->desc);
1665 ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
1666
1667 /* If this endpoint is already in use, and the upper layers are trying
1668 * to add it again without dropping it, reject the addition.
1669 */
1670 if (virt_dev->eps[ep_index].ring &&
1671 !(le32_to_cpu(ctrl_ctx->drop_flags) &
1672 xhci_get_endpoint_flag(&ep->desc))) {
1673 xhci_warn(xhci, "Trying to add endpoint 0x%x "
1674 "without dropping it.\n",
1675 (unsigned int) ep->desc.bEndpointAddress);
1676 return -EINVAL;
1677 }
1678
1679 /* If the HCD has already noted the endpoint is enabled,
1680 * ignore this request.
1681 */
1682 if (le32_to_cpu(ctrl_ctx->add_flags) &
1683 xhci_get_endpoint_flag(&ep->desc)) {
1684 xhci_warn(xhci, "xHCI %s called with enabled ep %p\n",
1685 __func__, ep);
1686 return 0;
1687 }
1688
1689 /*
1690 * Configuration and alternate setting changes must be done in
1691 * process context, not interrupt context (or so documenation
1692 * for usb_set_interface() and usb_set_configuration() claim).
1693 */
1694 if (xhci_endpoint_init(xhci, virt_dev, udev, ep, GFP_NOIO) < 0) {
1695 dev_dbg(&udev->dev, "%s - could not initialize ep %#x\n",
1696 __func__, ep->desc.bEndpointAddress);
1697 return -ENOMEM;
1698 }
1699
1700 ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
1701 new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
1702
1703 /* If xhci_endpoint_disable() was called for this endpoint, but the
1704 * xHC hasn't been notified yet through the check_bandwidth() call,
1705 * this re-adds a new state for the endpoint from the new endpoint
1706 * descriptors. We must drop and re-add this endpoint, so we leave the
1707 * drop flags alone.
1708 */
1709 new_drop_flags = le32_to_cpu(ctrl_ctx->drop_flags);
1710
1711 slot_ctx = xhci_get_slot_ctx(xhci, in_ctx);
1712 /* Update the last valid endpoint context, if we just added one past */
1713 if ((le32_to_cpu(slot_ctx->dev_info) & LAST_CTX_MASK) <
1714 LAST_CTX(last_ctx)) {
1715 slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
1716 slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(last_ctx));
1717 }
1718 new_slot_info = le32_to_cpu(slot_ctx->dev_info);
1719
1720 /* Store the usb_device pointer for later use */
1721 ep->hcpriv = udev;
1722
1723 xhci_dbg(xhci, "add ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x, new slot info = %#x\n",
1724 (unsigned int) ep->desc.bEndpointAddress,
1725 udev->slot_id,
1726 (unsigned int) new_drop_flags,
1727 (unsigned int) new_add_flags,
1728 (unsigned int) new_slot_info);
1729 return 0;
1730}
1731
1732static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev)
1733{
1734 struct xhci_input_control_ctx *ctrl_ctx;
1735 struct xhci_ep_ctx *ep_ctx;
1736 struct xhci_slot_ctx *slot_ctx;
1737 int i;
1738
1739 /* When a device's add flag and drop flag are zero, any subsequent
1740 * configure endpoint command will leave that endpoint's state
1741 * untouched. Make sure we don't leave any old state in the input
1742 * endpoint contexts.
1743 */
1744 ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx);
1745 ctrl_ctx->drop_flags = 0;
1746 ctrl_ctx->add_flags = 0;
1747 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
1748 slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
1749 /* Endpoint 0 is always valid */
1750 slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1));
1751 for (i = 1; i < 31; ++i) {
1752 ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, i);
1753 ep_ctx->ep_info = 0;
1754 ep_ctx->ep_info2 = 0;
1755 ep_ctx->deq = 0;
1756 ep_ctx->tx_info = 0;
1757 }
1758}
1759
1760static int xhci_configure_endpoint_result(struct xhci_hcd *xhci,
1761 struct usb_device *udev, u32 *cmd_status)
1762{
1763 int ret;
1764
1765 switch (*cmd_status) {
1766 case COMP_ENOMEM:
1767 dev_warn(&udev->dev, "Not enough host controller resources "
1768 "for new device state.\n");
1769 ret = -ENOMEM;
1770 /* FIXME: can we allocate more resources for the HC? */
1771 break;
1772 case COMP_BW_ERR:
1773 case COMP_2ND_BW_ERR:
1774 dev_warn(&udev->dev, "Not enough bandwidth "
1775 "for new device state.\n");
1776 ret = -ENOSPC;
1777 /* FIXME: can we go back to the old state? */
1778 break;
1779 case COMP_TRB_ERR:
1780 /* the HCD set up something wrong */
1781 dev_warn(&udev->dev, "ERROR: Endpoint drop flag = 0, "
1782 "add flag = 1, "
1783 "and endpoint is not disabled.\n");
1784 ret = -EINVAL;
1785 break;
1786 case COMP_DEV_ERR:
1787 dev_warn(&udev->dev, "ERROR: Incompatible device for endpoint "
1788 "configure command.\n");
1789 ret = -ENODEV;
1790 break;
1791 case COMP_SUCCESS:
1792 dev_dbg(&udev->dev, "Successful Endpoint Configure command\n");
1793 ret = 0;
1794 break;
1795 default:
1796 xhci_err(xhci, "ERROR: unexpected command completion "
1797 "code 0x%x.\n", *cmd_status);
1798 ret = -EINVAL;
1799 break;
1800 }
1801 return ret;
1802}
1803
1804static int xhci_evaluate_context_result(struct xhci_hcd *xhci,
1805 struct usb_device *udev, u32 *cmd_status)
1806{
1807 int ret;
1808 struct xhci_virt_device *virt_dev = xhci->devs[udev->slot_id];
1809
1810 switch (*cmd_status) {
1811 case COMP_EINVAL:
1812 dev_warn(&udev->dev, "WARN: xHCI driver setup invalid evaluate "
1813 "context command.\n");
1814 ret = -EINVAL;
1815 break;
1816 case COMP_EBADSLT:
1817 dev_warn(&udev->dev, "WARN: slot not enabled for"
1818 "evaluate context command.\n");
1819 case COMP_CTX_STATE:
1820 dev_warn(&udev->dev, "WARN: invalid context state for "
1821 "evaluate context command.\n");
1822 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 1);
1823 ret = -EINVAL;
1824 break;
1825 case COMP_DEV_ERR:
1826 dev_warn(&udev->dev, "ERROR: Incompatible device for evaluate "
1827 "context command.\n");
1828 ret = -ENODEV;
1829 break;
1830 case COMP_MEL_ERR:
1831 /* Max Exit Latency too large error */
1832 dev_warn(&udev->dev, "WARN: Max Exit Latency too large\n");
1833 ret = -EINVAL;
1834 break;
1835 case COMP_SUCCESS:
1836 dev_dbg(&udev->dev, "Successful evaluate context command\n");
1837 ret = 0;
1838 break;
1839 default:
1840 xhci_err(xhci, "ERROR: unexpected command completion "
1841 "code 0x%x.\n", *cmd_status);
1842 ret = -EINVAL;
1843 break;
1844 }
1845 return ret;
1846}
1847
1848static u32 xhci_count_num_new_endpoints(struct xhci_hcd *xhci,
1849 struct xhci_container_ctx *in_ctx)
1850{
1851 struct xhci_input_control_ctx *ctrl_ctx;
1852 u32 valid_add_flags;
1853 u32 valid_drop_flags;
1854
1855 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
1856 /* Ignore the slot flag (bit 0), and the default control endpoint flag
1857 * (bit 1). The default control endpoint is added during the Address
1858 * Device command and is never removed until the slot is disabled.
1859 */
1860 valid_add_flags = ctrl_ctx->add_flags >> 2;
1861 valid_drop_flags = ctrl_ctx->drop_flags >> 2;
1862
1863 /* Use hweight32 to count the number of ones in the add flags, or
1864 * number of endpoints added. Don't count endpoints that are changed
1865 * (both added and dropped).
1866 */
1867 return hweight32(valid_add_flags) -
1868 hweight32(valid_add_flags & valid_drop_flags);
1869}
1870
1871static unsigned int xhci_count_num_dropped_endpoints(struct xhci_hcd *xhci,
1872 struct xhci_container_ctx *in_ctx)
1873{
1874 struct xhci_input_control_ctx *ctrl_ctx;
1875 u32 valid_add_flags;
1876 u32 valid_drop_flags;
1877
1878 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
1879 valid_add_flags = ctrl_ctx->add_flags >> 2;
1880 valid_drop_flags = ctrl_ctx->drop_flags >> 2;
1881
1882 return hweight32(valid_drop_flags) -
1883 hweight32(valid_add_flags & valid_drop_flags);
1884}
1885
1886/*
1887 * We need to reserve the new number of endpoints before the configure endpoint
1888 * command completes. We can't subtract the dropped endpoints from the number
1889 * of active endpoints until the command completes because we can oversubscribe
1890 * the host in this case:
1891 *
1892 * - the first configure endpoint command drops more endpoints than it adds
1893 * - a second configure endpoint command that adds more endpoints is queued
1894 * - the first configure endpoint command fails, so the config is unchanged
1895 * - the second command may succeed, even though there isn't enough resources
1896 *
1897 * Must be called with xhci->lock held.
1898 */
1899static int xhci_reserve_host_resources(struct xhci_hcd *xhci,
1900 struct xhci_container_ctx *in_ctx)
1901{
1902 u32 added_eps;
1903
1904 added_eps = xhci_count_num_new_endpoints(xhci, in_ctx);
1905 if (xhci->num_active_eps + added_eps > xhci->limit_active_eps) {
1906 xhci_dbg(xhci, "Not enough ep ctxs: "
1907 "%u active, need to add %u, limit is %u.\n",
1908 xhci->num_active_eps, added_eps,
1909 xhci->limit_active_eps);
1910 return -ENOMEM;
1911 }
1912 xhci->num_active_eps += added_eps;
1913 xhci_dbg(xhci, "Adding %u ep ctxs, %u now active.\n", added_eps,
1914 xhci->num_active_eps);
1915 return 0;
1916}
1917
1918/*
1919 * The configure endpoint was failed by the xHC for some other reason, so we
1920 * need to revert the resources that failed configuration would have used.
1921 *
1922 * Must be called with xhci->lock held.
1923 */
1924static void xhci_free_host_resources(struct xhci_hcd *xhci,
1925 struct xhci_container_ctx *in_ctx)
1926{
1927 u32 num_failed_eps;
1928
1929 num_failed_eps = xhci_count_num_new_endpoints(xhci, in_ctx);
1930 xhci->num_active_eps -= num_failed_eps;
1931 xhci_dbg(xhci, "Removing %u failed ep ctxs, %u now active.\n",
1932 num_failed_eps,
1933 xhci->num_active_eps);
1934}
1935
1936/*
1937 * Now that the command has completed, clean up the active endpoint count by
1938 * subtracting out the endpoints that were dropped (but not changed).
1939 *
1940 * Must be called with xhci->lock held.
1941 */
1942static void xhci_finish_resource_reservation(struct xhci_hcd *xhci,
1943 struct xhci_container_ctx *in_ctx)
1944{
1945 u32 num_dropped_eps;
1946
1947 num_dropped_eps = xhci_count_num_dropped_endpoints(xhci, in_ctx);
1948 xhci->num_active_eps -= num_dropped_eps;
1949 if (num_dropped_eps)
1950 xhci_dbg(xhci, "Removing %u dropped ep ctxs, %u now active.\n",
1951 num_dropped_eps,
1952 xhci->num_active_eps);
1953}
1954
1955unsigned int xhci_get_block_size(struct usb_device *udev)
1956{
1957 switch (udev->speed) {
1958 case USB_SPEED_LOW:
1959 case USB_SPEED_FULL:
1960 return FS_BLOCK;
1961 case USB_SPEED_HIGH:
1962 return HS_BLOCK;
1963 case USB_SPEED_SUPER:
1964 return SS_BLOCK;
1965 case USB_SPEED_UNKNOWN:
1966 case USB_SPEED_WIRELESS:
1967 default:
1968 /* Should never happen */
1969 return 1;
1970 }
1971}
1972
1973unsigned int xhci_get_largest_overhead(struct xhci_interval_bw *interval_bw)
1974{
1975 if (interval_bw->overhead[LS_OVERHEAD_TYPE])
1976 return LS_OVERHEAD;
1977 if (interval_bw->overhead[FS_OVERHEAD_TYPE])
1978 return FS_OVERHEAD;
1979 return HS_OVERHEAD;
1980}
1981
1982/* If we are changing a LS/FS device under a HS hub,
1983 * make sure (if we are activating a new TT) that the HS bus has enough
1984 * bandwidth for this new TT.
1985 */
1986static int xhci_check_tt_bw_table(struct xhci_hcd *xhci,
1987 struct xhci_virt_device *virt_dev,
1988 int old_active_eps)
1989{
1990 struct xhci_interval_bw_table *bw_table;
1991 struct xhci_tt_bw_info *tt_info;
1992
1993 /* Find the bandwidth table for the root port this TT is attached to. */
1994 bw_table = &xhci->rh_bw[virt_dev->real_port - 1].bw_table;
1995 tt_info = virt_dev->tt_info;
1996 /* If this TT already had active endpoints, the bandwidth for this TT
1997 * has already been added. Removing all periodic endpoints (and thus
1998 * making the TT enactive) will only decrease the bandwidth used.
1999 */
2000 if (old_active_eps)
2001 return 0;
2002 if (old_active_eps == 0 && tt_info->active_eps != 0) {
2003 if (bw_table->bw_used + TT_HS_OVERHEAD > HS_BW_LIMIT)
2004 return -ENOMEM;
2005 return 0;
2006 }
2007 /* Not sure why we would have no new active endpoints...
2008 *
2009 * Maybe because of an Evaluate Context change for a hub update or a
2010 * control endpoint 0 max packet size change?
2011 * FIXME: skip the bandwidth calculation in that case.
2012 */
2013 return 0;
2014}
2015
2016static int xhci_check_ss_bw(struct xhci_hcd *xhci,
2017 struct xhci_virt_device *virt_dev)
2018{
2019 unsigned int bw_reserved;
2020
2021 bw_reserved = DIV_ROUND_UP(SS_BW_RESERVED*SS_BW_LIMIT_IN, 100);
2022 if (virt_dev->bw_table->ss_bw_in > (SS_BW_LIMIT_IN - bw_reserved))
2023 return -ENOMEM;
2024
2025 bw_reserved = DIV_ROUND_UP(SS_BW_RESERVED*SS_BW_LIMIT_OUT, 100);
2026 if (virt_dev->bw_table->ss_bw_out > (SS_BW_LIMIT_OUT - bw_reserved))
2027 return -ENOMEM;
2028
2029 return 0;
2030}
2031
2032/*
2033 * This algorithm is a very conservative estimate of the worst-case scheduling
2034 * scenario for any one interval. The hardware dynamically schedules the
2035 * packets, so we can't tell which microframe could be the limiting factor in
2036 * the bandwidth scheduling. This only takes into account periodic endpoints.
2037 *
2038 * Obviously, we can't solve an NP complete problem to find the minimum worst
2039 * case scenario. Instead, we come up with an estimate that is no less than
2040 * the worst case bandwidth used for any one microframe, but may be an
2041 * over-estimate.
2042 *
2043 * We walk the requirements for each endpoint by interval, starting with the
2044 * smallest interval, and place packets in the schedule where there is only one
2045 * possible way to schedule packets for that interval. In order to simplify
2046 * this algorithm, we record the largest max packet size for each interval, and
2047 * assume all packets will be that size.
2048 *
2049 * For interval 0, we obviously must schedule all packets for each interval.
2050 * The bandwidth for interval 0 is just the amount of data to be transmitted
2051 * (the sum of all max ESIT payload sizes, plus any overhead per packet times
2052 * the number of packets).
2053 *
2054 * For interval 1, we have two possible microframes to schedule those packets
2055 * in. For this algorithm, if we can schedule the same number of packets for
2056 * each possible scheduling opportunity (each microframe), we will do so. The
2057 * remaining number of packets will be saved to be transmitted in the gaps in
2058 * the next interval's scheduling sequence.
2059 *
2060 * As we move those remaining packets to be scheduled with interval 2 packets,
2061 * we have to double the number of remaining packets to transmit. This is
2062 * because the intervals are actually powers of 2, and we would be transmitting
2063 * the previous interval's packets twice in this interval. We also have to be
2064 * sure that when we look at the largest max packet size for this interval, we
2065 * also look at the largest max packet size for the remaining packets and take
2066 * the greater of the two.
2067 *
2068 * The algorithm continues to evenly distribute packets in each scheduling
2069 * opportunity, and push the remaining packets out, until we get to the last
2070 * interval. Then those packets and their associated overhead are just added
2071 * to the bandwidth used.
2072 */
2073static int xhci_check_bw_table(struct xhci_hcd *xhci,
2074 struct xhci_virt_device *virt_dev,
2075 int old_active_eps)
2076{
2077 unsigned int bw_reserved;
2078 unsigned int max_bandwidth;
2079 unsigned int bw_used;
2080 unsigned int block_size;
2081 struct xhci_interval_bw_table *bw_table;
2082 unsigned int packet_size = 0;
2083 unsigned int overhead = 0;
2084 unsigned int packets_transmitted = 0;
2085 unsigned int packets_remaining = 0;
2086 unsigned int i;
2087
2088 if (virt_dev->udev->speed == USB_SPEED_SUPER)
2089 return xhci_check_ss_bw(xhci, virt_dev);
2090
2091 if (virt_dev->udev->speed == USB_SPEED_HIGH) {
2092 max_bandwidth = HS_BW_LIMIT;
2093 /* Convert percent of bus BW reserved to blocks reserved */
2094 bw_reserved = DIV_ROUND_UP(HS_BW_RESERVED * max_bandwidth, 100);
2095 } else {
2096 max_bandwidth = FS_BW_LIMIT;
2097 bw_reserved = DIV_ROUND_UP(FS_BW_RESERVED * max_bandwidth, 100);
2098 }
2099
2100 bw_table = virt_dev->bw_table;
2101 /* We need to translate the max packet size and max ESIT payloads into
2102 * the units the hardware uses.
2103 */
2104 block_size = xhci_get_block_size(virt_dev->udev);
2105
2106 /* If we are manipulating a LS/FS device under a HS hub, double check
2107 * that the HS bus has enough bandwidth if we are activing a new TT.
2108 */
2109 if (virt_dev->tt_info) {
2110 xhci_dbg(xhci, "Recalculating BW for rootport %u\n",
2111 virt_dev->real_port);
2112 if (xhci_check_tt_bw_table(xhci, virt_dev, old_active_eps)) {
2113 xhci_warn(xhci, "Not enough bandwidth on HS bus for "
2114 "newly activated TT.\n");
2115 return -ENOMEM;
2116 }
2117 xhci_dbg(xhci, "Recalculating BW for TT slot %u port %u\n",
2118 virt_dev->tt_info->slot_id,
2119 virt_dev->tt_info->ttport);
2120 } else {
2121 xhci_dbg(xhci, "Recalculating BW for rootport %u\n",
2122 virt_dev->real_port);
2123 }
2124
2125 /* Add in how much bandwidth will be used for interval zero, or the
2126 * rounded max ESIT payload + number of packets * largest overhead.
2127 */
2128 bw_used = DIV_ROUND_UP(bw_table->interval0_esit_payload, block_size) +
2129 bw_table->interval_bw[0].num_packets *
2130 xhci_get_largest_overhead(&bw_table->interval_bw[0]);
2131
2132 for (i = 1; i < XHCI_MAX_INTERVAL; i++) {
2133 unsigned int bw_added;
2134 unsigned int largest_mps;
2135 unsigned int interval_overhead;
2136
2137 /*
2138 * How many packets could we transmit in this interval?
2139 * If packets didn't fit in the previous interval, we will need
2140 * to transmit that many packets twice within this interval.
2141 */
2142 packets_remaining = 2 * packets_remaining +
2143 bw_table->interval_bw[i].num_packets;
2144
2145 /* Find the largest max packet size of this or the previous
2146 * interval.
2147 */
2148 if (list_empty(&bw_table->interval_bw[i].endpoints))
2149 largest_mps = 0;
2150 else {
2151 struct xhci_virt_ep *virt_ep;
2152 struct list_head *ep_entry;
2153
2154 ep_entry = bw_table->interval_bw[i].endpoints.next;
2155 virt_ep = list_entry(ep_entry,
2156 struct xhci_virt_ep, bw_endpoint_list);
2157 /* Convert to blocks, rounding up */
2158 largest_mps = DIV_ROUND_UP(
2159 virt_ep->bw_info.max_packet_size,
2160 block_size);
2161 }
2162 if (largest_mps > packet_size)
2163 packet_size = largest_mps;
2164
2165 /* Use the larger overhead of this or the previous interval. */
2166 interval_overhead = xhci_get_largest_overhead(
2167 &bw_table->interval_bw[i]);
2168 if (interval_overhead > overhead)
2169 overhead = interval_overhead;
2170
2171 /* How many packets can we evenly distribute across
2172 * (1 << (i + 1)) possible scheduling opportunities?
2173 */
2174 packets_transmitted = packets_remaining >> (i + 1);
2175
2176 /* Add in the bandwidth used for those scheduled packets */
2177 bw_added = packets_transmitted * (overhead + packet_size);
2178
2179 /* How many packets do we have remaining to transmit? */
2180 packets_remaining = packets_remaining % (1 << (i + 1));
2181
2182 /* What largest max packet size should those packets have? */
2183 /* If we've transmitted all packets, don't carry over the
2184 * largest packet size.
2185 */
2186 if (packets_remaining == 0) {
2187 packet_size = 0;
2188 overhead = 0;
2189 } else if (packets_transmitted > 0) {
2190 /* Otherwise if we do have remaining packets, and we've
2191 * scheduled some packets in this interval, take the
2192 * largest max packet size from endpoints with this
2193 * interval.
2194 */
2195 packet_size = largest_mps;
2196 overhead = interval_overhead;
2197 }
2198 /* Otherwise carry over packet_size and overhead from the last
2199 * time we had a remainder.
2200 */
2201 bw_used += bw_added;
2202 if (bw_used > max_bandwidth) {
2203 xhci_warn(xhci, "Not enough bandwidth. "
2204 "Proposed: %u, Max: %u\n",
2205 bw_used, max_bandwidth);
2206 return -ENOMEM;
2207 }
2208 }
2209 /*
2210 * Ok, we know we have some packets left over after even-handedly
2211 * scheduling interval 15. We don't know which microframes they will
2212 * fit into, so we over-schedule and say they will be scheduled every
2213 * microframe.
2214 */
2215 if (packets_remaining > 0)
2216 bw_used += overhead + packet_size;
2217
2218 if (!virt_dev->tt_info && virt_dev->udev->speed == USB_SPEED_HIGH) {
2219 unsigned int port_index = virt_dev->real_port - 1;
2220
2221 /* OK, we're manipulating a HS device attached to a
2222 * root port bandwidth domain. Include the number of active TTs
2223 * in the bandwidth used.
2224 */
2225 bw_used += TT_HS_OVERHEAD *
2226 xhci->rh_bw[port_index].num_active_tts;
2227 }
2228
2229 xhci_dbg(xhci, "Final bandwidth: %u, Limit: %u, Reserved: %u, "
2230 "Available: %u " "percent\n",
2231 bw_used, max_bandwidth, bw_reserved,
2232 (max_bandwidth - bw_used - bw_reserved) * 100 /
2233 max_bandwidth);
2234
2235 bw_used += bw_reserved;
2236 if (bw_used > max_bandwidth) {
2237 xhci_warn(xhci, "Not enough bandwidth. Proposed: %u, Max: %u\n",
2238 bw_used, max_bandwidth);
2239 return -ENOMEM;
2240 }
2241
2242 bw_table->bw_used = bw_used;
2243 return 0;
2244}
2245
2246static bool xhci_is_async_ep(unsigned int ep_type)
2247{
2248 return (ep_type != ISOC_OUT_EP && ep_type != INT_OUT_EP &&
2249 ep_type != ISOC_IN_EP &&
2250 ep_type != INT_IN_EP);
2251}
2252
2253static bool xhci_is_sync_in_ep(unsigned int ep_type)
2254{
2255 return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
2256}
2257
2258static unsigned int xhci_get_ss_bw_consumed(struct xhci_bw_info *ep_bw)
2259{
2260 unsigned int mps = DIV_ROUND_UP(ep_bw->max_packet_size, SS_BLOCK);
2261
2262 if (ep_bw->ep_interval == 0)
2263 return SS_OVERHEAD_BURST +
2264 (ep_bw->mult * ep_bw->num_packets *
2265 (SS_OVERHEAD + mps));
2266 return DIV_ROUND_UP(ep_bw->mult * ep_bw->num_packets *
2267 (SS_OVERHEAD + mps + SS_OVERHEAD_BURST),
2268 1 << ep_bw->ep_interval);
2269
2270}
2271
2272void xhci_drop_ep_from_interval_table(struct xhci_hcd *xhci,
2273 struct xhci_bw_info *ep_bw,
2274 struct xhci_interval_bw_table *bw_table,
2275 struct usb_device *udev,
2276 struct xhci_virt_ep *virt_ep,
2277 struct xhci_tt_bw_info *tt_info)
2278{
2279 struct xhci_interval_bw *interval_bw;
2280 int normalized_interval;
2281
2282 if (xhci_is_async_ep(ep_bw->type))
2283 return;
2284
2285 if (udev->speed == USB_SPEED_SUPER) {
2286 if (xhci_is_sync_in_ep(ep_bw->type))
2287 xhci->devs[udev->slot_id]->bw_table->ss_bw_in -=
2288 xhci_get_ss_bw_consumed(ep_bw);
2289 else
2290 xhci->devs[udev->slot_id]->bw_table->ss_bw_out -=
2291 xhci_get_ss_bw_consumed(ep_bw);
2292 return;
2293 }
2294
2295 /* SuperSpeed endpoints never get added to intervals in the table, so
2296 * this check is only valid for HS/FS/LS devices.
2297 */
2298 if (list_empty(&virt_ep->bw_endpoint_list))
2299 return;
2300 /* For LS/FS devices, we need to translate the interval expressed in
2301 * microframes to frames.
2302 */
2303 if (udev->speed == USB_SPEED_HIGH)
2304 normalized_interval = ep_bw->ep_interval;
2305 else
2306 normalized_interval = ep_bw->ep_interval - 3;
2307
2308 if (normalized_interval == 0)
2309 bw_table->interval0_esit_payload -= ep_bw->max_esit_payload;
2310 interval_bw = &bw_table->interval_bw[normalized_interval];
2311 interval_bw->num_packets -= ep_bw->num_packets;
2312 switch (udev->speed) {
2313 case USB_SPEED_LOW:
2314 interval_bw->overhead[LS_OVERHEAD_TYPE] -= 1;
2315 break;
2316 case USB_SPEED_FULL:
2317 interval_bw->overhead[FS_OVERHEAD_TYPE] -= 1;
2318 break;
2319 case USB_SPEED_HIGH:
2320 interval_bw->overhead[HS_OVERHEAD_TYPE] -= 1;
2321 break;
2322 case USB_SPEED_SUPER:
2323 case USB_SPEED_UNKNOWN:
2324 case USB_SPEED_WIRELESS:
2325 /* Should never happen because only LS/FS/HS endpoints will get
2326 * added to the endpoint list.
2327 */
2328 return;
2329 }
2330 if (tt_info)
2331 tt_info->active_eps -= 1;
2332 list_del_init(&virt_ep->bw_endpoint_list);
2333}
2334
2335static void xhci_add_ep_to_interval_table(struct xhci_hcd *xhci,
2336 struct xhci_bw_info *ep_bw,
2337 struct xhci_interval_bw_table *bw_table,
2338 struct usb_device *udev,
2339 struct xhci_virt_ep *virt_ep,
2340 struct xhci_tt_bw_info *tt_info)
2341{
2342 struct xhci_interval_bw *interval_bw;
2343 struct xhci_virt_ep *smaller_ep;
2344 int normalized_interval;
2345
2346 if (xhci_is_async_ep(ep_bw->type))
2347 return;
2348
2349 if (udev->speed == USB_SPEED_SUPER) {
2350 if (xhci_is_sync_in_ep(ep_bw->type))
2351 xhci->devs[udev->slot_id]->bw_table->ss_bw_in +=
2352 xhci_get_ss_bw_consumed(ep_bw);
2353 else
2354 xhci->devs[udev->slot_id]->bw_table->ss_bw_out +=
2355 xhci_get_ss_bw_consumed(ep_bw);
2356 return;
2357 }
2358
2359 /* For LS/FS devices, we need to translate the interval expressed in
2360 * microframes to frames.
2361 */
2362 if (udev->speed == USB_SPEED_HIGH)
2363 normalized_interval = ep_bw->ep_interval;
2364 else
2365 normalized_interval = ep_bw->ep_interval - 3;
2366
2367 if (normalized_interval == 0)
2368 bw_table->interval0_esit_payload += ep_bw->max_esit_payload;
2369 interval_bw = &bw_table->interval_bw[normalized_interval];
2370 interval_bw->num_packets += ep_bw->num_packets;
2371 switch (udev->speed) {
2372 case USB_SPEED_LOW:
2373 interval_bw->overhead[LS_OVERHEAD_TYPE] += 1;
2374 break;
2375 case USB_SPEED_FULL:
2376 interval_bw->overhead[FS_OVERHEAD_TYPE] += 1;
2377 break;
2378 case USB_SPEED_HIGH:
2379 interval_bw->overhead[HS_OVERHEAD_TYPE] += 1;
2380 break;
2381 case USB_SPEED_SUPER:
2382 case USB_SPEED_UNKNOWN:
2383 case USB_SPEED_WIRELESS:
2384 /* Should never happen because only LS/FS/HS endpoints will get
2385 * added to the endpoint list.
2386 */
2387 return;
2388 }
2389
2390 if (tt_info)
2391 tt_info->active_eps += 1;
2392 /* Insert the endpoint into the list, largest max packet size first. */
2393 list_for_each_entry(smaller_ep, &interval_bw->endpoints,
2394 bw_endpoint_list) {
2395 if (ep_bw->max_packet_size >=
2396 smaller_ep->bw_info.max_packet_size) {
2397 /* Add the new ep before the smaller endpoint */
2398 list_add_tail(&virt_ep->bw_endpoint_list,
2399 &smaller_ep->bw_endpoint_list);
2400 return;
2401 }
2402 }
2403 /* Add the new endpoint at the end of the list. */
2404 list_add_tail(&virt_ep->bw_endpoint_list,
2405 &interval_bw->endpoints);
2406}
2407
2408void xhci_update_tt_active_eps(struct xhci_hcd *xhci,
2409 struct xhci_virt_device *virt_dev,
2410 int old_active_eps)
2411{
2412 struct xhci_root_port_bw_info *rh_bw_info;
2413 if (!virt_dev->tt_info)
2414 return;
2415
2416 rh_bw_info = &xhci->rh_bw[virt_dev->real_port - 1];
2417 if (old_active_eps == 0 &&
2418 virt_dev->tt_info->active_eps != 0) {
2419 rh_bw_info->num_active_tts += 1;
2420 rh_bw_info->bw_table.bw_used += TT_HS_OVERHEAD;
2421 } else if (old_active_eps != 0 &&
2422 virt_dev->tt_info->active_eps == 0) {
2423 rh_bw_info->num_active_tts -= 1;
2424 rh_bw_info->bw_table.bw_used -= TT_HS_OVERHEAD;
2425 }
2426}
2427
2428static int xhci_reserve_bandwidth(struct xhci_hcd *xhci,
2429 struct xhci_virt_device *virt_dev,
2430 struct xhci_container_ctx *in_ctx)
2431{
2432 struct xhci_bw_info ep_bw_info[31];
2433 int i;
2434 struct xhci_input_control_ctx *ctrl_ctx;
2435 int old_active_eps = 0;
2436
2437 if (virt_dev->tt_info)
2438 old_active_eps = virt_dev->tt_info->active_eps;
2439
2440 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
2441
2442 for (i = 0; i < 31; i++) {
2443 if (!EP_IS_ADDED(ctrl_ctx, i) && !EP_IS_DROPPED(ctrl_ctx, i))
2444 continue;
2445
2446 /* Make a copy of the BW info in case we need to revert this */
2447 memcpy(&ep_bw_info[i], &virt_dev->eps[i].bw_info,
2448 sizeof(ep_bw_info[i]));
2449 /* Drop the endpoint from the interval table if the endpoint is
2450 * being dropped or changed.
2451 */
2452 if (EP_IS_DROPPED(ctrl_ctx, i))
2453 xhci_drop_ep_from_interval_table(xhci,
2454 &virt_dev->eps[i].bw_info,
2455 virt_dev->bw_table,
2456 virt_dev->udev,
2457 &virt_dev->eps[i],
2458 virt_dev->tt_info);
2459 }
2460 /* Overwrite the information stored in the endpoints' bw_info */
2461 xhci_update_bw_info(xhci, virt_dev->in_ctx, ctrl_ctx, virt_dev);
2462 for (i = 0; i < 31; i++) {
2463 /* Add any changed or added endpoints to the interval table */
2464 if (EP_IS_ADDED(ctrl_ctx, i))
2465 xhci_add_ep_to_interval_table(xhci,
2466 &virt_dev->eps[i].bw_info,
2467 virt_dev->bw_table,
2468 virt_dev->udev,
2469 &virt_dev->eps[i],
2470 virt_dev->tt_info);
2471 }
2472
2473 if (!xhci_check_bw_table(xhci, virt_dev, old_active_eps)) {
2474 /* Ok, this fits in the bandwidth we have.
2475 * Update the number of active TTs.
2476 */
2477 xhci_update_tt_active_eps(xhci, virt_dev, old_active_eps);
2478 return 0;
2479 }
2480
2481 /* We don't have enough bandwidth for this, revert the stored info. */
2482 for (i = 0; i < 31; i++) {
2483 if (!EP_IS_ADDED(ctrl_ctx, i) && !EP_IS_DROPPED(ctrl_ctx, i))
2484 continue;
2485
2486 /* Drop the new copies of any added or changed endpoints from
2487 * the interval table.
2488 */
2489 if (EP_IS_ADDED(ctrl_ctx, i)) {
2490 xhci_drop_ep_from_interval_table(xhci,
2491 &virt_dev->eps[i].bw_info,
2492 virt_dev->bw_table,
2493 virt_dev->udev,
2494 &virt_dev->eps[i],
2495 virt_dev->tt_info);
2496 }
2497 /* Revert the endpoint back to its old information */
2498 memcpy(&virt_dev->eps[i].bw_info, &ep_bw_info[i],
2499 sizeof(ep_bw_info[i]));
2500 /* Add any changed or dropped endpoints back into the table */
2501 if (EP_IS_DROPPED(ctrl_ctx, i))
2502 xhci_add_ep_to_interval_table(xhci,
2503 &virt_dev->eps[i].bw_info,
2504 virt_dev->bw_table,
2505 virt_dev->udev,
2506 &virt_dev->eps[i],
2507 virt_dev->tt_info);
2508 }
2509 return -ENOMEM;
2510}
2511
2512
2513/* Issue a configure endpoint command or evaluate context command
2514 * and wait for it to finish.
2515 */
2516static int xhci_configure_endpoint(struct xhci_hcd *xhci,
2517 struct usb_device *udev,
2518 struct xhci_command *command,
2519 bool ctx_change, bool must_succeed)
2520{
2521 int ret;
2522 int timeleft;
2523 unsigned long flags;
2524 struct xhci_container_ctx *in_ctx;
2525 struct completion *cmd_completion;
2526 u32 *cmd_status;
2527 struct xhci_virt_device *virt_dev;
2528 union xhci_trb *cmd_trb;
2529
2530 spin_lock_irqsave(&xhci->lock, flags);
2531 virt_dev = xhci->devs[udev->slot_id];
2532
2533 if (command)
2534 in_ctx = command->in_ctx;
2535 else
2536 in_ctx = virt_dev->in_ctx;
2537
2538 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK) &&
2539 xhci_reserve_host_resources(xhci, in_ctx)) {
2540 spin_unlock_irqrestore(&xhci->lock, flags);
2541 xhci_warn(xhci, "Not enough host resources, "
2542 "active endpoint contexts = %u\n",
2543 xhci->num_active_eps);
2544 return -ENOMEM;
2545 }
2546 if ((xhci->quirks & XHCI_SW_BW_CHECKING) &&
2547 xhci_reserve_bandwidth(xhci, virt_dev, in_ctx)) {
2548 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK))
2549 xhci_free_host_resources(xhci, in_ctx);
2550 spin_unlock_irqrestore(&xhci->lock, flags);
2551 xhci_warn(xhci, "Not enough bandwidth\n");
2552 return -ENOMEM;
2553 }
2554
2555 if (command) {
2556 cmd_completion = command->completion;
2557 cmd_status = &command->status;
2558 command->command_trb = xhci->cmd_ring->enqueue;
2559
2560 /* Enqueue pointer can be left pointing to the link TRB,
2561 * we must handle that
2562 */
2563 if (TRB_TYPE_LINK_LE32(command->command_trb->link.control))
2564 command->command_trb =
2565 xhci->cmd_ring->enq_seg->next->trbs;
2566
2567 list_add_tail(&command->cmd_list, &virt_dev->cmd_list);
2568 } else {
2569 cmd_completion = &virt_dev->cmd_completion;
2570 cmd_status = &virt_dev->cmd_status;
2571 }
2572 init_completion(cmd_completion);
2573
2574 cmd_trb = xhci->cmd_ring->dequeue;
2575 if (!ctx_change)
2576 ret = xhci_queue_configure_endpoint(xhci, in_ctx->dma,
2577 udev->slot_id, must_succeed);
2578 else
2579 ret = xhci_queue_evaluate_context(xhci, in_ctx->dma,
2580 udev->slot_id, must_succeed);
2581 if (ret < 0) {
2582 if (command)
2583 list_del(&command->cmd_list);
2584 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK))
2585 xhci_free_host_resources(xhci, in_ctx);
2586 spin_unlock_irqrestore(&xhci->lock, flags);
2587 xhci_dbg(xhci, "FIXME allocate a new ring segment\n");
2588 return -ENOMEM;
2589 }
2590 xhci_ring_cmd_db(xhci);
2591 spin_unlock_irqrestore(&xhci->lock, flags);
2592
2593 /* Wait for the configure endpoint command to complete */
2594 timeleft = wait_for_completion_interruptible_timeout(
2595 cmd_completion,
2596 XHCI_CMD_DEFAULT_TIMEOUT);
2597 if (timeleft <= 0) {
2598 xhci_warn(xhci, "%s while waiting for %s command\n",
2599 timeleft == 0 ? "Timeout" : "Signal",
2600 ctx_change == 0 ?
2601 "configure endpoint" :
2602 "evaluate context");
2603 /* cancel the configure endpoint command */
2604 ret = xhci_cancel_cmd(xhci, command, cmd_trb);
2605 if (ret < 0)
2606 return ret;
2607 return -ETIME;
2608 }
2609
2610 if (!ctx_change)
2611 ret = xhci_configure_endpoint_result(xhci, udev, cmd_status);
2612 else
2613 ret = xhci_evaluate_context_result(xhci, udev, cmd_status);
2614
2615 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) {
2616 spin_lock_irqsave(&xhci->lock, flags);
2617 /* If the command failed, remove the reserved resources.
2618 * Otherwise, clean up the estimate to include dropped eps.
2619 */
2620 if (ret)
2621 xhci_free_host_resources(xhci, in_ctx);
2622 else
2623 xhci_finish_resource_reservation(xhci, in_ctx);
2624 spin_unlock_irqrestore(&xhci->lock, flags);
2625 }
2626 return ret;
2627}
2628
2629/* Called after one or more calls to xhci_add_endpoint() or
2630 * xhci_drop_endpoint(). If this call fails, the USB core is expected
2631 * to call xhci_reset_bandwidth().
2632 *
2633 * Since we are in the middle of changing either configuration or
2634 * installing a new alt setting, the USB core won't allow URBs to be
2635 * enqueued for any endpoint on the old config or interface. Nothing
2636 * else should be touching the xhci->devs[slot_id] structure, so we
2637 * don't need to take the xhci->lock for manipulating that.
2638 */
2639int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
2640{
2641 int i;
2642 int ret = 0;
2643 struct xhci_hcd *xhci;
2644 struct xhci_virt_device *virt_dev;
2645 struct xhci_input_control_ctx *ctrl_ctx;
2646 struct xhci_slot_ctx *slot_ctx;
2647
2648 ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
2649 if (ret <= 0)
2650 return ret;
2651 xhci = hcd_to_xhci(hcd);
2652 if (xhci->xhc_state & XHCI_STATE_DYING)
2653 return -ENODEV;
2654
2655 xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev);
2656 virt_dev = xhci->devs[udev->slot_id];
2657
2658 /* See section 4.6.6 - A0 = 1; A1 = D0 = D1 = 0 */
2659 ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx);
2660 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
2661 ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG);
2662 ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG));
2663
2664 /* Don't issue the command if there's no endpoints to update. */
2665 if (ctrl_ctx->add_flags == cpu_to_le32(SLOT_FLAG) &&
2666 ctrl_ctx->drop_flags == 0)
2667 return 0;
2668
2669 xhci_dbg(xhci, "New Input Control Context:\n");
2670 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
2671 xhci_dbg_ctx(xhci, virt_dev->in_ctx,
2672 LAST_CTX_TO_EP_NUM(le32_to_cpu(slot_ctx->dev_info)));
2673
2674 ret = xhci_configure_endpoint(xhci, udev, NULL,
2675 false, false);
2676 if (ret) {
2677 /* Callee should call reset_bandwidth() */
2678 return ret;
2679 }
2680
2681 xhci_dbg(xhci, "Output context after successful config ep cmd:\n");
2682 xhci_dbg_ctx(xhci, virt_dev->out_ctx,
2683 LAST_CTX_TO_EP_NUM(le32_to_cpu(slot_ctx->dev_info)));
2684
2685 /* Free any rings that were dropped, but not changed. */
2686 for (i = 1; i < 31; ++i) {
2687 if ((le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1))) &&
2688 !(le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1))))
2689 xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i);
2690 }
2691 xhci_zero_in_ctx(xhci, virt_dev);
2692 /*
2693 * Install any rings for completely new endpoints or changed endpoints,
2694 * and free or cache any old rings from changed endpoints.
2695 */
2696 for (i = 1; i < 31; ++i) {
2697 if (!virt_dev->eps[i].new_ring)
2698 continue;
2699 /* Only cache or free the old ring if it exists.
2700 * It may not if this is the first add of an endpoint.
2701 */
2702 if (virt_dev->eps[i].ring) {
2703 xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i);
2704 }
2705 virt_dev->eps[i].ring = virt_dev->eps[i].new_ring;
2706 virt_dev->eps[i].new_ring = NULL;
2707 }
2708
2709 return ret;
2710}
2711
2712void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
2713{
2714 struct xhci_hcd *xhci;
2715 struct xhci_virt_device *virt_dev;
2716 int i, ret;
2717
2718 ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
2719 if (ret <= 0)
2720 return;
2721 xhci = hcd_to_xhci(hcd);
2722
2723 xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev);
2724 virt_dev = xhci->devs[udev->slot_id];
2725 /* Free any rings allocated for added endpoints */
2726 for (i = 0; i < 31; ++i) {
2727 if (virt_dev->eps[i].new_ring) {
2728 xhci_ring_free(xhci, virt_dev->eps[i].new_ring);
2729 virt_dev->eps[i].new_ring = NULL;
2730 }
2731 }
2732 xhci_zero_in_ctx(xhci, virt_dev);
2733}
2734
2735static void xhci_setup_input_ctx_for_config_ep(struct xhci_hcd *xhci,
2736 struct xhci_container_ctx *in_ctx,
2737 struct xhci_container_ctx *out_ctx,
2738 u32 add_flags, u32 drop_flags)
2739{
2740 struct xhci_input_control_ctx *ctrl_ctx;
2741 ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
2742 ctrl_ctx->add_flags = cpu_to_le32(add_flags);
2743 ctrl_ctx->drop_flags = cpu_to_le32(drop_flags);
2744 xhci_slot_copy(xhci, in_ctx, out_ctx);
2745 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
2746
2747 xhci_dbg(xhci, "Input Context:\n");
2748 xhci_dbg_ctx(xhci, in_ctx, xhci_last_valid_endpoint(add_flags));
2749}
2750
2751static void xhci_setup_input_ctx_for_quirk(struct xhci_hcd *xhci,
2752 unsigned int slot_id, unsigned int ep_index,
2753 struct xhci_dequeue_state *deq_state)
2754{
2755 struct xhci_container_ctx *in_ctx;
2756 struct xhci_ep_ctx *ep_ctx;
2757 u32 added_ctxs;
2758 dma_addr_t addr;
2759
2760 xhci_endpoint_copy(xhci, xhci->devs[slot_id]->in_ctx,
2761 xhci->devs[slot_id]->out_ctx, ep_index);
2762 in_ctx = xhci->devs[slot_id]->in_ctx;
2763 ep_ctx = xhci_get_ep_ctx(xhci, in_ctx, ep_index);
2764 addr = xhci_trb_virt_to_dma(deq_state->new_deq_seg,
2765 deq_state->new_deq_ptr);
2766 if (addr == 0) {
2767 xhci_warn(xhci, "WARN Cannot submit config ep after "
2768 "reset ep command\n");
2769 xhci_warn(xhci, "WARN deq seg = %p, deq ptr = %p\n",
2770 deq_state->new_deq_seg,
2771 deq_state->new_deq_ptr);
2772 return;
2773 }
2774 ep_ctx->deq = cpu_to_le64(addr | deq_state->new_cycle_state);
2775
2776 added_ctxs = xhci_get_endpoint_flag_from_index(ep_index);
2777 xhci_setup_input_ctx_for_config_ep(xhci, xhci->devs[slot_id]->in_ctx,
2778 xhci->devs[slot_id]->out_ctx, added_ctxs, added_ctxs);
2779}
2780
2781void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci,
2782 struct usb_device *udev, unsigned int ep_index)
2783{
2784 struct xhci_dequeue_state deq_state;
2785 struct xhci_virt_ep *ep;
2786
2787 xhci_dbg(xhci, "Cleaning up stalled endpoint ring\n");
2788 ep = &xhci->devs[udev->slot_id]->eps[ep_index];
2789 /* We need to move the HW's dequeue pointer past this TD,
2790 * or it will attempt to resend it on the next doorbell ring.
2791 */
2792 xhci_find_new_dequeue_state(xhci, udev->slot_id,
2793 ep_index, ep->stopped_stream, ep->stopped_td,
2794 &deq_state);
2795
2796 /* HW with the reset endpoint quirk will use the saved dequeue state to
2797 * issue a configure endpoint command later.
2798 */
2799 if (!(xhci->quirks & XHCI_RESET_EP_QUIRK)) {
2800 xhci_dbg(xhci, "Queueing new dequeue state\n");
2801 xhci_queue_new_dequeue_state(xhci, udev->slot_id,
2802 ep_index, ep->stopped_stream, &deq_state);
2803 } else {
2804 /* Better hope no one uses the input context between now and the
2805 * reset endpoint completion!
2806 * XXX: No idea how this hardware will react when stream rings
2807 * are enabled.
2808 */
2809 xhci_dbg(xhci, "Setting up input context for "
2810 "configure endpoint command\n");
2811 xhci_setup_input_ctx_for_quirk(xhci, udev->slot_id,
2812 ep_index, &deq_state);
2813 }
2814}
2815
2816/* Deal with stalled endpoints. The core should have sent the control message
2817 * to clear the halt condition. However, we need to make the xHCI hardware
2818 * reset its sequence number, since a device will expect a sequence number of
2819 * zero after the halt condition is cleared.
2820 * Context: in_interrupt
2821 */
2822void xhci_endpoint_reset(struct usb_hcd *hcd,
2823 struct usb_host_endpoint *ep)
2824{
2825 struct xhci_hcd *xhci;
2826 struct usb_device *udev;
2827 unsigned int ep_index;
2828 unsigned long flags;
2829 int ret;
2830 struct xhci_virt_ep *virt_ep;
2831
2832 xhci = hcd_to_xhci(hcd);
2833 udev = (struct usb_device *) ep->hcpriv;
2834 /* Called with a root hub endpoint (or an endpoint that wasn't added
2835 * with xhci_add_endpoint()
2836 */
2837 if (!ep->hcpriv)
2838 return;
2839 ep_index = xhci_get_endpoint_index(&ep->desc);
2840 virt_ep = &xhci->devs[udev->slot_id]->eps[ep_index];
2841 if (!virt_ep->stopped_td) {
2842 xhci_dbg(xhci, "Endpoint 0x%x not halted, refusing to reset.\n",
2843 ep->desc.bEndpointAddress);
2844 return;
2845 }
2846 if (usb_endpoint_xfer_control(&ep->desc)) {
2847 xhci_dbg(xhci, "Control endpoint stall already handled.\n");
2848 return;
2849 }
2850
2851 xhci_dbg(xhci, "Queueing reset endpoint command\n");
2852 spin_lock_irqsave(&xhci->lock, flags);
2853 ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index);
2854 /*
2855 * Can't change the ring dequeue pointer until it's transitioned to the
2856 * stopped state, which is only upon a successful reset endpoint
2857 * command. Better hope that last command worked!
2858 */
2859 if (!ret) {
2860 xhci_cleanup_stalled_ring(xhci, udev, ep_index);
2861 kfree(virt_ep->stopped_td);
2862 xhci_ring_cmd_db(xhci);
2863 }
2864 virt_ep->stopped_td = NULL;
2865 virt_ep->stopped_trb = NULL;
2866 virt_ep->stopped_stream = 0;
2867 spin_unlock_irqrestore(&xhci->lock, flags);
2868
2869 if (ret)
2870 xhci_warn(xhci, "FIXME allocate a new ring segment\n");
2871}
2872
2873static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,
2874 struct usb_device *udev, struct usb_host_endpoint *ep,
2875 unsigned int slot_id)
2876{
2877 int ret;
2878 unsigned int ep_index;
2879 unsigned int ep_state;
2880
2881 if (!ep)
2882 return -EINVAL;
2883 ret = xhci_check_args(xhci_to_hcd(xhci), udev, ep, 1, true, __func__);
2884 if (ret <= 0)
2885 return -EINVAL;
2886 if (ep->ss_ep_comp.bmAttributes == 0) {
2887 xhci_warn(xhci, "WARN: SuperSpeed Endpoint Companion"
2888 " descriptor for ep 0x%x does not support streams\n",
2889 ep->desc.bEndpointAddress);
2890 return -EINVAL;
2891 }
2892
2893 ep_index = xhci_get_endpoint_index(&ep->desc);
2894 ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
2895 if (ep_state & EP_HAS_STREAMS ||
2896 ep_state & EP_GETTING_STREAMS) {
2897 xhci_warn(xhci, "WARN: SuperSpeed bulk endpoint 0x%x "
2898 "already has streams set up.\n",
2899 ep->desc.bEndpointAddress);
2900 xhci_warn(xhci, "Send email to xHCI maintainer and ask for "
2901 "dynamic stream context array reallocation.\n");
2902 return -EINVAL;
2903 }
2904 if (!list_empty(&xhci->devs[slot_id]->eps[ep_index].ring->td_list)) {
2905 xhci_warn(xhci, "Cannot setup streams for SuperSpeed bulk "
2906 "endpoint 0x%x; URBs are pending.\n",
2907 ep->desc.bEndpointAddress);
2908 return -EINVAL;
2909 }
2910 return 0;
2911}
2912
2913static void xhci_calculate_streams_entries(struct xhci_hcd *xhci,
2914 unsigned int *num_streams, unsigned int *num_stream_ctxs)
2915{
2916 unsigned int max_streams;
2917
2918 /* The stream context array size must be a power of two */
2919 *num_stream_ctxs = roundup_pow_of_two(*num_streams);
2920 /*
2921 * Find out how many primary stream array entries the host controller
2922 * supports. Later we may use secondary stream arrays (similar to 2nd
2923 * level page entries), but that's an optional feature for xHCI host
2924 * controllers. xHCs must support at least 4 stream IDs.
2925 */
2926 max_streams = HCC_MAX_PSA(xhci->hcc_params);
2927 if (*num_stream_ctxs > max_streams) {
2928 xhci_dbg(xhci, "xHCI HW only supports %u stream ctx entries.\n",
2929 max_streams);
2930 *num_stream_ctxs = max_streams;
2931 *num_streams = max_streams;
2932 }
2933}
2934
2935/* Returns an error code if one of the endpoint already has streams.
2936 * This does not change any data structures, it only checks and gathers
2937 * information.
2938 */
2939static int xhci_calculate_streams_and_bitmask(struct xhci_hcd *xhci,
2940 struct usb_device *udev,
2941 struct usb_host_endpoint **eps, unsigned int num_eps,
2942 unsigned int *num_streams, u32 *changed_ep_bitmask)
2943{
2944 unsigned int max_streams;
2945 unsigned int endpoint_flag;
2946 int i;
2947 int ret;
2948
2949 for (i = 0; i < num_eps; i++) {
2950 ret = xhci_check_streams_endpoint(xhci, udev,
2951 eps[i], udev->slot_id);
2952 if (ret < 0)
2953 return ret;
2954
2955 max_streams = usb_ss_max_streams(&eps[i]->ss_ep_comp);
2956 if (max_streams < (*num_streams - 1)) {
2957 xhci_dbg(xhci, "Ep 0x%x only supports %u stream IDs.\n",
2958 eps[i]->desc.bEndpointAddress,
2959 max_streams);
2960 *num_streams = max_streams+1;
2961 }
2962
2963 endpoint_flag = xhci_get_endpoint_flag(&eps[i]->desc);
2964 if (*changed_ep_bitmask & endpoint_flag)
2965 return -EINVAL;
2966 *changed_ep_bitmask |= endpoint_flag;
2967 }
2968 return 0;
2969}
2970
2971static u32 xhci_calculate_no_streams_bitmask(struct xhci_hcd *xhci,
2972 struct usb_device *udev,
2973 struct usb_host_endpoint **eps, unsigned int num_eps)
2974{
2975 u32 changed_ep_bitmask = 0;
2976 unsigned int slot_id;
2977 unsigned int ep_index;
2978 unsigned int ep_state;
2979 int i;
2980
2981 slot_id = udev->slot_id;
2982 if (!xhci->devs[slot_id])
2983 return 0;
2984
2985 for (i = 0; i < num_eps; i++) {
2986 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
2987 ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
2988 /* Are streams already being freed for the endpoint? */
2989 if (ep_state & EP_GETTING_NO_STREAMS) {
2990 xhci_warn(xhci, "WARN Can't disable streams for "
2991 "endpoint 0x%x\n, "
2992 "streams are being disabled already.",
2993 eps[i]->desc.bEndpointAddress);
2994 return 0;
2995 }
2996 /* Are there actually any streams to free? */
2997 if (!(ep_state & EP_HAS_STREAMS) &&
2998 !(ep_state & EP_GETTING_STREAMS)) {
2999 xhci_warn(xhci, "WARN Can't disable streams for "
3000 "endpoint 0x%x\n, "
3001 "streams are already disabled!",
3002 eps[i]->desc.bEndpointAddress);
3003 xhci_warn(xhci, "WARN xhci_free_streams() called "
3004 "with non-streams endpoint\n");
3005 return 0;
3006 }
3007 changed_ep_bitmask |= xhci_get_endpoint_flag(&eps[i]->desc);
3008 }
3009 return changed_ep_bitmask;
3010}
3011
3012/*
3013 * The USB device drivers use this function (though the HCD interface in USB
3014 * core) to prepare a set of bulk endpoints to use streams. Streams are used to
3015 * coordinate mass storage command queueing across multiple endpoints (basically
3016 * a stream ID == a task ID).
3017 *
3018 * Setting up streams involves allocating the same size stream context array
3019 * for each endpoint and issuing a configure endpoint command for all endpoints.
3020 *
3021 * Don't allow the call to succeed if one endpoint only supports one stream
3022 * (which means it doesn't support streams at all).
3023 *
3024 * Drivers may get less stream IDs than they asked for, if the host controller
3025 * hardware or endpoints claim they can't support the number of requested
3026 * stream IDs.
3027 */
3028int xhci_alloc_streams(struct usb_hcd *hcd, struct usb_device *udev,
3029 struct usb_host_endpoint **eps, unsigned int num_eps,
3030 unsigned int num_streams, gfp_t mem_flags)
3031{
3032 int i, ret;
3033 struct xhci_hcd *xhci;
3034 struct xhci_virt_device *vdev;
3035 struct xhci_command *config_cmd;
3036 unsigned int ep_index;
3037 unsigned int num_stream_ctxs;
3038 unsigned long flags;
3039 u32 changed_ep_bitmask = 0;
3040
3041 if (!eps)
3042 return -EINVAL;
3043
3044 /* Add one to the number of streams requested to account for
3045 * stream 0 that is reserved for xHCI usage.
3046 */
3047 num_streams += 1;
3048 xhci = hcd_to_xhci(hcd);
3049 xhci_dbg(xhci, "Driver wants %u stream IDs (including stream 0).\n",
3050 num_streams);
3051
3052 config_cmd = xhci_alloc_command(xhci, true, true, mem_flags);
3053 if (!config_cmd) {
3054 xhci_dbg(xhci, "Could not allocate xHCI command structure.\n");
3055 return -ENOMEM;
3056 }
3057
3058 /* Check to make sure all endpoints are not already configured for
3059 * streams. While we're at it, find the maximum number of streams that
3060 * all the endpoints will support and check for duplicate endpoints.
3061 */
3062 spin_lock_irqsave(&xhci->lock, flags);
3063 ret = xhci_calculate_streams_and_bitmask(xhci, udev, eps,
3064 num_eps, &num_streams, &changed_ep_bitmask);
3065 if (ret < 0) {
3066 xhci_free_command(xhci, config_cmd);
3067 spin_unlock_irqrestore(&xhci->lock, flags);
3068 return ret;
3069 }
3070 if (num_streams <= 1) {
3071 xhci_warn(xhci, "WARN: endpoints can't handle "
3072 "more than one stream.\n");
3073 xhci_free_command(xhci, config_cmd);
3074 spin_unlock_irqrestore(&xhci->lock, flags);
3075 return -EINVAL;
3076 }
3077 vdev = xhci->devs[udev->slot_id];
3078 /* Mark each endpoint as being in transition, so
3079 * xhci_urb_enqueue() will reject all URBs.
3080 */
3081 for (i = 0; i < num_eps; i++) {
3082 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3083 vdev->eps[ep_index].ep_state |= EP_GETTING_STREAMS;
3084 }
3085 spin_unlock_irqrestore(&xhci->lock, flags);
3086
3087 /* Setup internal data structures and allocate HW data structures for
3088 * streams (but don't install the HW structures in the input context
3089 * until we're sure all memory allocation succeeded).
3090 */
3091 xhci_calculate_streams_entries(xhci, &num_streams, &num_stream_ctxs);
3092 xhci_dbg(xhci, "Need %u stream ctx entries for %u stream IDs.\n",
3093 num_stream_ctxs, num_streams);
3094
3095 for (i = 0; i < num_eps; i++) {
3096 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3097 vdev->eps[ep_index].stream_info = xhci_alloc_stream_info(xhci,
3098 num_stream_ctxs,
3099 num_streams, mem_flags);
3100 if (!vdev->eps[ep_index].stream_info)
3101 goto cleanup;
3102 /* Set maxPstreams in endpoint context and update deq ptr to
3103 * point to stream context array. FIXME
3104 */
3105 }
3106
3107 /* Set up the input context for a configure endpoint command. */
3108 for (i = 0; i < num_eps; i++) {
3109 struct xhci_ep_ctx *ep_ctx;
3110
3111 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3112 ep_ctx = xhci_get_ep_ctx(xhci, config_cmd->in_ctx, ep_index);
3113
3114 xhci_endpoint_copy(xhci, config_cmd->in_ctx,
3115 vdev->out_ctx, ep_index);
3116 xhci_setup_streams_ep_input_ctx(xhci, ep_ctx,
3117 vdev->eps[ep_index].stream_info);
3118 }
3119 /* Tell the HW to drop its old copy of the endpoint context info
3120 * and add the updated copy from the input context.
3121 */
3122 xhci_setup_input_ctx_for_config_ep(xhci, config_cmd->in_ctx,
3123 vdev->out_ctx, changed_ep_bitmask, changed_ep_bitmask);
3124
3125 /* Issue and wait for the configure endpoint command */
3126 ret = xhci_configure_endpoint(xhci, udev, config_cmd,
3127 false, false);
3128
3129 /* xHC rejected the configure endpoint command for some reason, so we
3130 * leave the old ring intact and free our internal streams data
3131 * structure.
3132 */
3133 if (ret < 0)
3134 goto cleanup;
3135
3136 spin_lock_irqsave(&xhci->lock, flags);
3137 for (i = 0; i < num_eps; i++) {
3138 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3139 vdev->eps[ep_index].ep_state &= ~EP_GETTING_STREAMS;
3140 xhci_dbg(xhci, "Slot %u ep ctx %u now has streams.\n",
3141 udev->slot_id, ep_index);
3142 vdev->eps[ep_index].ep_state |= EP_HAS_STREAMS;
3143 }
3144 xhci_free_command(xhci, config_cmd);
3145 spin_unlock_irqrestore(&xhci->lock, flags);
3146
3147 /* Subtract 1 for stream 0, which drivers can't use */
3148 return num_streams - 1;
3149
3150cleanup:
3151 /* If it didn't work, free the streams! */
3152 for (i = 0; i < num_eps; i++) {
3153 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3154 xhci_free_stream_info(xhci, vdev->eps[ep_index].stream_info);
3155 vdev->eps[ep_index].stream_info = NULL;
3156 /* FIXME Unset maxPstreams in endpoint context and
3157 * update deq ptr to point to normal string ring.
3158 */
3159 vdev->eps[ep_index].ep_state &= ~EP_GETTING_STREAMS;
3160 vdev->eps[ep_index].ep_state &= ~EP_HAS_STREAMS;
3161 xhci_endpoint_zero(xhci, vdev, eps[i]);
3162 }
3163 xhci_free_command(xhci, config_cmd);
3164 return -ENOMEM;
3165}
3166
3167/* Transition the endpoint from using streams to being a "normal" endpoint
3168 * without streams.
3169 *
3170 * Modify the endpoint context state, submit a configure endpoint command,
3171 * and free all endpoint rings for streams if that completes successfully.
3172 */
3173int xhci_free_streams(struct usb_hcd *hcd, struct usb_device *udev,
3174 struct usb_host_endpoint **eps, unsigned int num_eps,
3175 gfp_t mem_flags)
3176{
3177 int i, ret;
3178 struct xhci_hcd *xhci;
3179 struct xhci_virt_device *vdev;
3180 struct xhci_command *command;
3181 unsigned int ep_index;
3182 unsigned long flags;
3183 u32 changed_ep_bitmask;
3184
3185 xhci = hcd_to_xhci(hcd);
3186 vdev = xhci->devs[udev->slot_id];
3187
3188 /* Set up a configure endpoint command to remove the streams rings */
3189 spin_lock_irqsave(&xhci->lock, flags);
3190 changed_ep_bitmask = xhci_calculate_no_streams_bitmask(xhci,
3191 udev, eps, num_eps);
3192 if (changed_ep_bitmask == 0) {
3193 spin_unlock_irqrestore(&xhci->lock, flags);
3194 return -EINVAL;
3195 }
3196
3197 /* Use the xhci_command structure from the first endpoint. We may have
3198 * allocated too many, but the driver may call xhci_free_streams() for
3199 * each endpoint it grouped into one call to xhci_alloc_streams().
3200 */
3201 ep_index = xhci_get_endpoint_index(&eps[0]->desc);
3202 command = vdev->eps[ep_index].stream_info->free_streams_command;
3203 for (i = 0; i < num_eps; i++) {
3204 struct xhci_ep_ctx *ep_ctx;
3205
3206 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3207 ep_ctx = xhci_get_ep_ctx(xhci, command->in_ctx, ep_index);
3208 xhci->devs[udev->slot_id]->eps[ep_index].ep_state |=
3209 EP_GETTING_NO_STREAMS;
3210
3211 xhci_endpoint_copy(xhci, command->in_ctx,
3212 vdev->out_ctx, ep_index);
3213 xhci_setup_no_streams_ep_input_ctx(xhci, ep_ctx,
3214 &vdev->eps[ep_index]);
3215 }
3216 xhci_setup_input_ctx_for_config_ep(xhci, command->in_ctx,
3217 vdev->out_ctx, changed_ep_bitmask, changed_ep_bitmask);
3218 spin_unlock_irqrestore(&xhci->lock, flags);
3219
3220 /* Issue and wait for the configure endpoint command,
3221 * which must succeed.
3222 */
3223 ret = xhci_configure_endpoint(xhci, udev, command,
3224 false, true);
3225
3226 /* xHC rejected the configure endpoint command for some reason, so we
3227 * leave the streams rings intact.
3228 */
3229 if (ret < 0)
3230 return ret;
3231
3232 spin_lock_irqsave(&xhci->lock, flags);
3233 for (i = 0; i < num_eps; i++) {
3234 ep_index = xhci_get_endpoint_index(&eps[i]->desc);
3235 xhci_free_stream_info(xhci, vdev->eps[ep_index].stream_info);
3236 vdev->eps[ep_index].stream_info = NULL;
3237 /* FIXME Unset maxPstreams in endpoint context and
3238 * update deq ptr to point to normal string ring.
3239 */
3240 vdev->eps[ep_index].ep_state &= ~EP_GETTING_NO_STREAMS;
3241 vdev->eps[ep_index].ep_state &= ~EP_HAS_STREAMS;
3242 }
3243 spin_unlock_irqrestore(&xhci->lock, flags);
3244
3245 return 0;
3246}
3247
3248/*
3249 * Deletes endpoint resources for endpoints that were active before a Reset
3250 * Device command, or a Disable Slot command. The Reset Device command leaves
3251 * the control endpoint intact, whereas the Disable Slot command deletes it.
3252 *
3253 * Must be called with xhci->lock held.
3254 */
3255void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci,
3256 struct xhci_virt_device *virt_dev, bool drop_control_ep)
3257{
3258 int i;
3259 unsigned int num_dropped_eps = 0;
3260 unsigned int drop_flags = 0;
3261
3262 for (i = (drop_control_ep ? 0 : 1); i < 31; i++) {
3263 if (virt_dev->eps[i].ring) {
3264 drop_flags |= 1 << i;
3265 num_dropped_eps++;
3266 }
3267 }
3268 xhci->num_active_eps -= num_dropped_eps;
3269 if (num_dropped_eps)
3270 xhci_dbg(xhci, "Dropped %u ep ctxs, flags = 0x%x, "
3271 "%u now active.\n",
3272 num_dropped_eps, drop_flags,
3273 xhci->num_active_eps);
3274}
3275
3276/*
3277 * This submits a Reset Device Command, which will set the device state to 0,
3278 * set the device address to 0, and disable all the endpoints except the default
3279 * control endpoint. The USB core should come back and call
3280 * xhci_address_device(), and then re-set up the configuration. If this is
3281 * called because of a usb_reset_and_verify_device(), then the old alternate
3282 * settings will be re-installed through the normal bandwidth allocation
3283 * functions.
3284 *
3285 * Wait for the Reset Device command to finish. Remove all structures
3286 * associated with the endpoints that were disabled. Clear the input device
3287 * structure? Cache the rings? Reset the control endpoint 0 max packet size?
3288 *
3289 * If the virt_dev to be reset does not exist or does not match the udev,
3290 * it means the device is lost, possibly due to the xHC restore error and
3291 * re-initialization during S3/S4. In this case, call xhci_alloc_dev() to
3292 * re-allocate the device.
3293 */
3294int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev)
3295{
3296 int ret, i;
3297 unsigned long flags;
3298 struct xhci_hcd *xhci;
3299 unsigned int slot_id;
3300 struct xhci_virt_device *virt_dev;
3301 struct xhci_command *reset_device_cmd;
3302 int timeleft;
3303 int last_freed_endpoint;
3304 struct xhci_slot_ctx *slot_ctx;
3305 int old_active_eps = 0;
3306
3307 ret = xhci_check_args(hcd, udev, NULL, 0, false, __func__);
3308 if (ret <= 0)
3309 return ret;
3310 xhci = hcd_to_xhci(hcd);
3311 slot_id = udev->slot_id;
3312 virt_dev = xhci->devs[slot_id];
3313 if (!virt_dev) {
3314 xhci_dbg(xhci, "The device to be reset with slot ID %u does "
3315 "not exist. Re-allocate the device\n", slot_id);
3316 ret = xhci_alloc_dev(hcd, udev);
3317 if (ret == 1)
3318 return 0;
3319 else
3320 return -EINVAL;
3321 }
3322
3323 if (virt_dev->udev != udev) {
3324 /* If the virt_dev and the udev does not match, this virt_dev
3325 * may belong to another udev.
3326 * Re-allocate the device.
3327 */
3328 xhci_dbg(xhci, "The device to be reset with slot ID %u does "
3329 "not match the udev. Re-allocate the device\n",
3330 slot_id);
3331 ret = xhci_alloc_dev(hcd, udev);
3332 if (ret == 1)
3333 return 0;
3334 else
3335 return -EINVAL;
3336 }
3337
3338 /* If device is not setup, there is no point in resetting it */
3339 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
3340 if (GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)) ==
3341 SLOT_STATE_DISABLED)
3342 return 0;
3343
3344 xhci_dbg(xhci, "Resetting device with slot ID %u\n", slot_id);
3345 /* Allocate the command structure that holds the struct completion.
3346 * Assume we're in process context, since the normal device reset
3347 * process has to wait for the device anyway. Storage devices are
3348 * reset as part of error handling, so use GFP_NOIO instead of
3349 * GFP_KERNEL.
3350 */
3351 reset_device_cmd = xhci_alloc_command(xhci, false, true, GFP_NOIO);
3352 if (!reset_device_cmd) {
3353 xhci_dbg(xhci, "Couldn't allocate command structure.\n");
3354 return -ENOMEM;
3355 }
3356
3357 /* Attempt to submit the Reset Device command to the command ring */
3358 spin_lock_irqsave(&xhci->lock, flags);
3359 reset_device_cmd->command_trb = xhci->cmd_ring->enqueue;
3360
3361 /* Enqueue pointer can be left pointing to the link TRB,
3362 * we must handle that
3363 */
3364 if (TRB_TYPE_LINK_LE32(reset_device_cmd->command_trb->link.control))
3365 reset_device_cmd->command_trb =
3366 xhci->cmd_ring->enq_seg->next->trbs;
3367
3368 list_add_tail(&reset_device_cmd->cmd_list, &virt_dev->cmd_list);
3369 ret = xhci_queue_reset_device(xhci, slot_id);
3370 if (ret) {
3371 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3372 list_del(&reset_device_cmd->cmd_list);
3373 spin_unlock_irqrestore(&xhci->lock, flags);
3374 goto command_cleanup;
3375 }
3376 xhci_ring_cmd_db(xhci);
3377 spin_unlock_irqrestore(&xhci->lock, flags);
3378
3379 /* Wait for the Reset Device command to finish */
3380 timeleft = wait_for_completion_interruptible_timeout(
3381 reset_device_cmd->completion,
3382 USB_CTRL_SET_TIMEOUT);
3383 if (timeleft <= 0) {
3384 xhci_warn(xhci, "%s while waiting for reset device command\n",
3385 timeleft == 0 ? "Timeout" : "Signal");
3386 spin_lock_irqsave(&xhci->lock, flags);
3387 /* The timeout might have raced with the event ring handler, so
3388 * only delete from the list if the item isn't poisoned.
3389 */
3390 if (reset_device_cmd->cmd_list.next != LIST_POISON1)
3391 list_del(&reset_device_cmd->cmd_list);
3392 spin_unlock_irqrestore(&xhci->lock, flags);
3393 ret = -ETIME;
3394 goto command_cleanup;
3395 }
3396
3397 /* The Reset Device command can't fail, according to the 0.95/0.96 spec,
3398 * unless we tried to reset a slot ID that wasn't enabled,
3399 * or the device wasn't in the addressed or configured state.
3400 */
3401 ret = reset_device_cmd->status;
3402 switch (ret) {
3403 case COMP_EBADSLT: /* 0.95 completion code for bad slot ID */
3404 case COMP_CTX_STATE: /* 0.96 completion code for same thing */
3405 xhci_info(xhci, "Can't reset device (slot ID %u) in %s state\n",
3406 slot_id,
3407 xhci_get_slot_state(xhci, virt_dev->out_ctx));
3408 xhci_info(xhci, "Not freeing device rings.\n");
3409 /* Don't treat this as an error. May change my mind later. */
3410 ret = 0;
3411 goto command_cleanup;
3412 case COMP_SUCCESS:
3413 xhci_dbg(xhci, "Successful reset device command.\n");
3414 break;
3415 default:
3416 if (xhci_is_vendor_info_code(xhci, ret))
3417 break;
3418 xhci_warn(xhci, "Unknown completion code %u for "
3419 "reset device command.\n", ret);
3420 ret = -EINVAL;
3421 goto command_cleanup;
3422 }
3423
3424 /* Free up host controller endpoint resources */
3425 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) {
3426 spin_lock_irqsave(&xhci->lock, flags);
3427 /* Don't delete the default control endpoint resources */
3428 xhci_free_device_endpoint_resources(xhci, virt_dev, false);
3429 spin_unlock_irqrestore(&xhci->lock, flags);
3430 }
3431
3432 /* Everything but endpoint 0 is disabled, so free or cache the rings. */
3433 last_freed_endpoint = 1;
3434 for (i = 1; i < 31; ++i) {
3435 struct xhci_virt_ep *ep = &virt_dev->eps[i];
3436
3437 if (ep->ep_state & EP_HAS_STREAMS) {
3438 xhci_free_stream_info(xhci, ep->stream_info);
3439 ep->stream_info = NULL;
3440 ep->ep_state &= ~EP_HAS_STREAMS;
3441 }
3442
3443 if (ep->ring) {
3444 xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i);
3445 last_freed_endpoint = i;
3446 }
3447 if (!list_empty(&virt_dev->eps[i].bw_endpoint_list))
3448 xhci_drop_ep_from_interval_table(xhci,
3449 &virt_dev->eps[i].bw_info,
3450 virt_dev->bw_table,
3451 udev,
3452 &virt_dev->eps[i],
3453 virt_dev->tt_info);
3454 xhci_clear_endpoint_bw_info(&virt_dev->eps[i].bw_info);
3455 }
3456 /* If necessary, update the number of active TTs on this root port */
3457 xhci_update_tt_active_eps(xhci, virt_dev, old_active_eps);
3458
3459 xhci_dbg(xhci, "Output context after successful reset device cmd:\n");
3460 xhci_dbg_ctx(xhci, virt_dev->out_ctx, last_freed_endpoint);
3461 ret = 0;
3462
3463command_cleanup:
3464 xhci_free_command(xhci, reset_device_cmd);
3465 return ret;
3466}
3467
3468/*
3469 * At this point, the struct usb_device is about to go away, the device has
3470 * disconnected, and all traffic has been stopped and the endpoints have been
3471 * disabled. Free any HC data structures associated with that device.
3472 */
3473void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev)
3474{
3475 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3476 struct xhci_virt_device *virt_dev;
3477 unsigned long flags;
3478 u32 state;
3479 int i, ret;
3480
3481 ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
3482 /* If the host is halted due to driver unload, we still need to free the
3483 * device.
3484 */
3485 if (ret <= 0 && ret != -ENODEV)
3486 return;
3487
3488 virt_dev = xhci->devs[udev->slot_id];
3489
3490 /* Stop any wayward timer functions (which may grab the lock) */
3491 for (i = 0; i < 31; ++i) {
3492 virt_dev->eps[i].ep_state &= ~EP_HALT_PENDING;
3493 del_timer_sync(&virt_dev->eps[i].stop_cmd_timer);
3494 }
3495
3496 if (udev->usb2_hw_lpm_enabled) {
3497 xhci_set_usb2_hardware_lpm(hcd, udev, 0);
3498 udev->usb2_hw_lpm_enabled = 0;
3499 }
3500
3501 spin_lock_irqsave(&xhci->lock, flags);
3502 /* Don't disable the slot if the host controller is dead. */
3503 state = xhci_readl(xhci, &xhci->op_regs->status);
3504 if (state == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING) ||
3505 (xhci->xhc_state & XHCI_STATE_HALTED)) {
3506 xhci_free_virt_device(xhci, udev->slot_id);
3507 spin_unlock_irqrestore(&xhci->lock, flags);
3508 return;
3509 }
3510
3511 if (xhci_queue_slot_control(xhci, TRB_DISABLE_SLOT, udev->slot_id)) {
3512 spin_unlock_irqrestore(&xhci->lock, flags);
3513 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3514 return;
3515 }
3516 xhci_ring_cmd_db(xhci);
3517 spin_unlock_irqrestore(&xhci->lock, flags);
3518 /*
3519 * Event command completion handler will free any data structures
3520 * associated with the slot. XXX Can free sleep?
3521 */
3522}
3523
3524/*
3525 * Checks if we have enough host controller resources for the default control
3526 * endpoint.
3527 *
3528 * Must be called with xhci->lock held.
3529 */
3530static int xhci_reserve_host_control_ep_resources(struct xhci_hcd *xhci)
3531{
3532 if (xhci->num_active_eps + 1 > xhci->limit_active_eps) {
3533 xhci_dbg(xhci, "Not enough ep ctxs: "
3534 "%u active, need to add 1, limit is %u.\n",
3535 xhci->num_active_eps, xhci->limit_active_eps);
3536 return -ENOMEM;
3537 }
3538 xhci->num_active_eps += 1;
3539 xhci_dbg(xhci, "Adding 1 ep ctx, %u now active.\n",
3540 xhci->num_active_eps);
3541 return 0;
3542}
3543
3544
3545/*
3546 * Returns 0 if the xHC ran out of device slots, the Enable Slot command
3547 * timed out, or allocating memory failed. Returns 1 on success.
3548 */
3549int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev)
3550{
3551 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3552 unsigned long flags;
3553 int timeleft;
3554 int ret;
3555 union xhci_trb *cmd_trb;
3556
3557 spin_lock_irqsave(&xhci->lock, flags);
3558 cmd_trb = xhci->cmd_ring->dequeue;
3559 ret = xhci_queue_slot_control(xhci, TRB_ENABLE_SLOT, 0);
3560 if (ret) {
3561 spin_unlock_irqrestore(&xhci->lock, flags);
3562 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3563 return 0;
3564 }
3565 xhci_ring_cmd_db(xhci);
3566 spin_unlock_irqrestore(&xhci->lock, flags);
3567
3568 /* XXX: how much time for xHC slot assignment? */
3569 timeleft = wait_for_completion_interruptible_timeout(&xhci->addr_dev,
3570 XHCI_CMD_DEFAULT_TIMEOUT);
3571 if (timeleft <= 0) {
3572 xhci_warn(xhci, "%s while waiting for a slot\n",
3573 timeleft == 0 ? "Timeout" : "Signal");
3574 /* cancel the enable slot request */
3575 return xhci_cancel_cmd(xhci, NULL, cmd_trb);
3576 }
3577
3578 if (!xhci->slot_id) {
3579 xhci_err(xhci, "Error while assigning device slot ID\n");
3580 return 0;
3581 }
3582
3583 if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) {
3584 spin_lock_irqsave(&xhci->lock, flags);
3585 ret = xhci_reserve_host_control_ep_resources(xhci);
3586 if (ret) {
3587 spin_unlock_irqrestore(&xhci->lock, flags);
3588 xhci_warn(xhci, "Not enough host resources, "
3589 "active endpoint contexts = %u\n",
3590 xhci->num_active_eps);
3591 goto disable_slot;
3592 }
3593 spin_unlock_irqrestore(&xhci->lock, flags);
3594 }
3595 /* Use GFP_NOIO, since this function can be called from
3596 * xhci_discover_or_reset_device(), which may be called as part of
3597 * mass storage driver error handling.
3598 */
3599 if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_NOIO)) {
3600 xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n");
3601 goto disable_slot;
3602 }
3603 udev->slot_id = xhci->slot_id;
3604 /* Is this a LS or FS device under a HS hub? */
3605 /* Hub or peripherial? */
3606 return 1;
3607
3608disable_slot:
3609 /* Disable slot, if we can do it without mem alloc */
3610 spin_lock_irqsave(&xhci->lock, flags);
3611 if (!xhci_queue_slot_control(xhci, TRB_DISABLE_SLOT, udev->slot_id))
3612 xhci_ring_cmd_db(xhci);
3613 spin_unlock_irqrestore(&xhci->lock, flags);
3614 return 0;
3615}
3616
3617/*
3618 * Issue an Address Device command (which will issue a SetAddress request to
3619 * the device).
3620 * We should be protected by the usb_address0_mutex in khubd's hub_port_init, so
3621 * we should only issue and wait on one address command at the same time.
3622 *
3623 * We add one to the device address issued by the hardware because the USB core
3624 * uses address 1 for the root hubs (even though they're not really devices).
3625 */
3626int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
3627{
3628 unsigned long flags;
3629 int timeleft;
3630 struct xhci_virt_device *virt_dev;
3631 int ret = 0;
3632 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3633 struct xhci_slot_ctx *slot_ctx;
3634 struct xhci_input_control_ctx *ctrl_ctx;
3635 u64 temp_64;
3636 union xhci_trb *cmd_trb;
3637
3638 if (!udev->slot_id) {
3639 xhci_dbg(xhci, "Bad Slot ID %d\n", udev->slot_id);
3640 return -EINVAL;
3641 }
3642
3643 virt_dev = xhci->devs[udev->slot_id];
3644
3645 if (WARN_ON(!virt_dev)) {
3646 /*
3647 * In plug/unplug torture test with an NEC controller,
3648 * a zero-dereference was observed once due to virt_dev = 0.
3649 * Print useful debug rather than crash if it is observed again!
3650 */
3651 xhci_warn(xhci, "Virt dev invalid for slot_id 0x%x!\n",
3652 udev->slot_id);
3653 return -EINVAL;
3654 }
3655
3656 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
3657 /*
3658 * If this is the first Set Address since device plug-in or
3659 * virt_device realloaction after a resume with an xHCI power loss,
3660 * then set up the slot context.
3661 */
3662 if (!slot_ctx->dev_info)
3663 xhci_setup_addressable_virt_dev(xhci, udev);
3664 /* Otherwise, update the control endpoint ring enqueue pointer. */
3665 else
3666 xhci_copy_ep0_dequeue_into_input_ctx(xhci, udev);
3667 ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx);
3668 ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG);
3669 ctrl_ctx->drop_flags = 0;
3670
3671 xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
3672 xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
3673
3674 spin_lock_irqsave(&xhci->lock, flags);
3675 cmd_trb = xhci->cmd_ring->dequeue;
3676 ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma,
3677 udev->slot_id);
3678 if (ret) {
3679 spin_unlock_irqrestore(&xhci->lock, flags);
3680 xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
3681 return ret;
3682 }
3683 xhci_ring_cmd_db(xhci);
3684 spin_unlock_irqrestore(&xhci->lock, flags);
3685
3686 /* ctrl tx can take up to 5 sec; XXX: need more time for xHC? */
3687 timeleft = wait_for_completion_interruptible_timeout(&xhci->addr_dev,
3688 XHCI_CMD_DEFAULT_TIMEOUT);
3689 /* FIXME: From section 4.3.4: "Software shall be responsible for timing
3690 * the SetAddress() "recovery interval" required by USB and aborting the
3691 * command on a timeout.
3692 */
3693 if (timeleft <= 0) {
3694 xhci_warn(xhci, "%s while waiting for address device command\n",
3695 timeleft == 0 ? "Timeout" : "Signal");
3696 /* cancel the address device command */
3697 ret = xhci_cancel_cmd(xhci, NULL, cmd_trb);
3698 if (ret < 0)
3699 return ret;
3700 return -ETIME;
3701 }
3702
3703 switch (virt_dev->cmd_status) {
3704 case COMP_CTX_STATE:
3705 case COMP_EBADSLT:
3706 xhci_err(xhci, "Setup ERROR: address device command for slot %d.\n",
3707 udev->slot_id);
3708 ret = -EINVAL;
3709 break;
3710 case COMP_TX_ERR:
3711 dev_warn(&udev->dev, "Device not responding to set address.\n");
3712 ret = -EPROTO;
3713 break;
3714 case COMP_DEV_ERR:
3715 dev_warn(&udev->dev, "ERROR: Incompatible device for address "
3716 "device command.\n");
3717 ret = -ENODEV;
3718 break;
3719 case COMP_SUCCESS:
3720 xhci_dbg(xhci, "Successful Address Device command\n");
3721 break;
3722 default:
3723 xhci_err(xhci, "ERROR: unexpected command completion "
3724 "code 0x%x.\n", virt_dev->cmd_status);
3725 xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
3726 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2);
3727 ret = -EINVAL;
3728 break;
3729 }
3730 if (ret) {
3731 return ret;
3732 }
3733 temp_64 = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
3734 xhci_dbg(xhci, "Op regs DCBAA ptr = %#016llx\n", temp_64);
3735 xhci_dbg(xhci, "Slot ID %d dcbaa entry @%p = %#016llx\n",
3736 udev->slot_id,
3737 &xhci->dcbaa->dev_context_ptrs[udev->slot_id],
3738 (unsigned long long)
3739 le64_to_cpu(xhci->dcbaa->dev_context_ptrs[udev->slot_id]));
3740 xhci_dbg(xhci, "Output Context DMA address = %#08llx\n",
3741 (unsigned long long)virt_dev->out_ctx->dma);
3742 xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
3743 xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
3744 xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
3745 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2);
3746 /*
3747 * USB core uses address 1 for the roothubs, so we add one to the
3748 * address given back to us by the HC.
3749 */
3750 slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
3751 /* Use kernel assigned address for devices; store xHC assigned
3752 * address locally. */
3753 virt_dev->address = (le32_to_cpu(slot_ctx->dev_state) & DEV_ADDR_MASK)
3754 + 1;
3755 /* Zero the input context control for later use */
3756 ctrl_ctx->add_flags = 0;
3757 ctrl_ctx->drop_flags = 0;
3758
3759 xhci_dbg(xhci, "Internal device address = %d\n", virt_dev->address);
3760
3761 return 0;
3762}
3763
3764#ifdef CONFIG_USB_SUSPEND
3765
3766/* BESL to HIRD Encoding array for USB2 LPM */
3767static int xhci_besl_encoding[16] = {125, 150, 200, 300, 400, 500, 1000, 2000,
3768 3000, 4000, 5000, 6000, 7000, 8000, 9000, 10000};
3769
3770/* Calculate HIRD/BESL for USB2 PORTPMSC*/
3771static int xhci_calculate_hird_besl(struct xhci_hcd *xhci,
3772 struct usb_device *udev)
3773{
3774 int u2del, besl, besl_host;
3775 int besl_device = 0;
3776 u32 field;
3777
3778 u2del = HCS_U2_LATENCY(xhci->hcs_params3);
3779 field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);
3780
3781 if (field & USB_BESL_SUPPORT) {
3782 for (besl_host = 0; besl_host < 16; besl_host++) {
3783 if (xhci_besl_encoding[besl_host] >= u2del)
3784 break;
3785 }
3786 /* Use baseline BESL value as default */
3787 if (field & USB_BESL_BASELINE_VALID)
3788 besl_device = USB_GET_BESL_BASELINE(field);
3789 else if (field & USB_BESL_DEEP_VALID)
3790 besl_device = USB_GET_BESL_DEEP(field);
3791 } else {
3792 if (u2del <= 50)
3793 besl_host = 0;
3794 else
3795 besl_host = (u2del - 51) / 75 + 1;
3796 }
3797
3798 besl = besl_host + besl_device;
3799 if (besl > 15)
3800 besl = 15;
3801
3802 return besl;
3803}
3804
3805static int xhci_usb2_software_lpm_test(struct usb_hcd *hcd,
3806 struct usb_device *udev)
3807{
3808 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3809 struct dev_info *dev_info;
3810 __le32 __iomem **port_array;
3811 __le32 __iomem *addr, *pm_addr;
3812 u32 temp, dev_id;
3813 unsigned int port_num;
3814 unsigned long flags;
3815 int hird;
3816 int ret;
3817
3818 if (hcd->speed == HCD_USB3 || !xhci->sw_lpm_support ||
3819 !udev->lpm_capable)
3820 return -EINVAL;
3821
3822 /* we only support lpm for non-hub device connected to root hub yet */
3823 if (!udev->parent || udev->parent->parent ||
3824 udev->descriptor.bDeviceClass == USB_CLASS_HUB)
3825 return -EINVAL;
3826
3827 spin_lock_irqsave(&xhci->lock, flags);
3828
3829 /* Look for devices in lpm_failed_devs list */
3830 dev_id = le16_to_cpu(udev->descriptor.idVendor) << 16 |
3831 le16_to_cpu(udev->descriptor.idProduct);
3832 list_for_each_entry(dev_info, &xhci->lpm_failed_devs, list) {
3833 if (dev_info->dev_id == dev_id) {
3834 ret = -EINVAL;
3835 goto finish;
3836 }
3837 }
3838
3839 port_array = xhci->usb2_ports;
3840 port_num = udev->portnum - 1;
3841
3842 if (port_num > HCS_MAX_PORTS(xhci->hcs_params1)) {
3843 xhci_dbg(xhci, "invalid port number %d\n", udev->portnum);
3844 ret = -EINVAL;
3845 goto finish;
3846 }
3847
3848 /*
3849 * Test USB 2.0 software LPM.
3850 * FIXME: some xHCI 1.0 hosts may implement a new register to set up
3851 * hardware-controlled USB 2.0 LPM. See section 5.4.11 and 4.23.5.1.1.1
3852 * in the June 2011 errata release.
3853 */
3854 xhci_dbg(xhci, "test port %d software LPM\n", port_num);
3855 /*
3856 * Set L1 Device Slot and HIRD/BESL.
3857 * Check device's USB 2.0 extension descriptor to determine whether
3858 * HIRD or BESL shoule be used. See USB2.0 LPM errata.
3859 */
3860 pm_addr = port_array[port_num] + 1;
3861 hird = xhci_calculate_hird_besl(xhci, udev);
3862 temp = PORT_L1DS(udev->slot_id) | PORT_HIRD(hird);
3863 xhci_writel(xhci, temp, pm_addr);
3864
3865 /* Set port link state to U2(L1) */
3866 addr = port_array[port_num];
3867 xhci_set_link_state(xhci, port_array, port_num, XDEV_U2);
3868
3869 /* wait for ACK */
3870 spin_unlock_irqrestore(&xhci->lock, flags);
3871 msleep(10);
3872 spin_lock_irqsave(&xhci->lock, flags);
3873
3874 /* Check L1 Status */
3875 ret = handshake(xhci, pm_addr, PORT_L1S_MASK, PORT_L1S_SUCCESS, 125);
3876 if (ret != -ETIMEDOUT) {
3877 /* enter L1 successfully */
3878 temp = xhci_readl(xhci, addr);
3879 xhci_dbg(xhci, "port %d entered L1 state, port status 0x%x\n",
3880 port_num, temp);
3881 ret = 0;
3882 } else {
3883 temp = xhci_readl(xhci, pm_addr);
3884 xhci_dbg(xhci, "port %d software lpm failed, L1 status %d\n",
3885 port_num, temp & PORT_L1S_MASK);
3886 ret = -EINVAL;
3887 }
3888
3889 /* Resume the port */
3890 xhci_set_link_state(xhci, port_array, port_num, XDEV_U0);
3891
3892 spin_unlock_irqrestore(&xhci->lock, flags);
3893 msleep(10);
3894 spin_lock_irqsave(&xhci->lock, flags);
3895
3896 /* Clear PLC */
3897 xhci_test_and_clear_bit(xhci, port_array, port_num, PORT_PLC);
3898
3899 /* Check PORTSC to make sure the device is in the right state */
3900 if (!ret) {
3901 temp = xhci_readl(xhci, addr);
3902 xhci_dbg(xhci, "resumed port %d status 0x%x\n", port_num, temp);
3903 if (!(temp & PORT_CONNECT) || !(temp & PORT_PE) ||
3904 (temp & PORT_PLS_MASK) != XDEV_U0) {
3905 xhci_dbg(xhci, "port L1 resume fail\n");
3906 ret = -EINVAL;
3907 }
3908 }
3909
3910 if (ret) {
3911 /* Insert dev to lpm_failed_devs list */
3912 xhci_warn(xhci, "device LPM test failed, may disconnect and "
3913 "re-enumerate\n");
3914 dev_info = kzalloc(sizeof(struct dev_info), GFP_ATOMIC);
3915 if (!dev_info) {
3916 ret = -ENOMEM;
3917 goto finish;
3918 }
3919 dev_info->dev_id = dev_id;
3920 INIT_LIST_HEAD(&dev_info->list);
3921 list_add(&dev_info->list, &xhci->lpm_failed_devs);
3922 } else {
3923 xhci_ring_device(xhci, udev->slot_id);
3924 }
3925
3926finish:
3927 spin_unlock_irqrestore(&xhci->lock, flags);
3928 return ret;
3929}
3930
3931int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
3932 struct usb_device *udev, int enable)
3933{
3934 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3935 __le32 __iomem **port_array;
3936 __le32 __iomem *pm_addr;
3937 u32 temp;
3938 unsigned int port_num;
3939 unsigned long flags;
3940 int hird;
3941
3942 if (hcd->speed == HCD_USB3 || !xhci->hw_lpm_support ||
3943 !udev->lpm_capable)
3944 return -EPERM;
3945
3946 if (!udev->parent || udev->parent->parent ||
3947 udev->descriptor.bDeviceClass == USB_CLASS_HUB)
3948 return -EPERM;
3949
3950 if (udev->usb2_hw_lpm_capable != 1)
3951 return -EPERM;
3952
3953 spin_lock_irqsave(&xhci->lock, flags);
3954
3955 port_array = xhci->usb2_ports;
3956 port_num = udev->portnum - 1;
3957 pm_addr = port_array[port_num] + 1;
3958 temp = xhci_readl(xhci, pm_addr);
3959
3960 xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
3961 enable ? "enable" : "disable", port_num);
3962
3963 hird = xhci_calculate_hird_besl(xhci, udev);
3964
3965 if (enable) {
3966 temp &= ~PORT_HIRD_MASK;
3967 temp |= PORT_HIRD(hird) | PORT_RWE;
3968 xhci_writel(xhci, temp, pm_addr);
3969 temp = xhci_readl(xhci, pm_addr);
3970 temp |= PORT_HLE;
3971 xhci_writel(xhci, temp, pm_addr);
3972 } else {
3973 temp &= ~(PORT_HLE | PORT_RWE | PORT_HIRD_MASK);
3974 xhci_writel(xhci, temp, pm_addr);
3975 }
3976
3977 spin_unlock_irqrestore(&xhci->lock, flags);
3978 return 0;
3979}
3980
3981int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
3982{
3983 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
3984 int ret;
3985
3986 ret = xhci_usb2_software_lpm_test(hcd, udev);
3987 if (!ret) {
3988 xhci_dbg(xhci, "software LPM test succeed\n");
3989 if (xhci->hw_lpm_support == 1) {
3990 udev->usb2_hw_lpm_capable = 1;
3991 ret = xhci_set_usb2_hardware_lpm(hcd, udev, 1);
3992 if (!ret)
3993 udev->usb2_hw_lpm_enabled = 1;
3994 }
3995 }
3996
3997 return 0;
3998}
3999
4000#else
4001
4002int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
4003 struct usb_device *udev, int enable)
4004{
4005 return 0;
4006}
4007
4008int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
4009{
4010 return 0;
4011}
4012
4013#endif /* CONFIG_USB_SUSPEND */
4014
4015/*---------------------- USB 3.0 Link PM functions ------------------------*/
4016
4017#ifdef CONFIG_PM
4018/* Service interval in nanoseconds = 2^(bInterval - 1) * 125us * 1000ns / 1us */
4019static unsigned long long xhci_service_interval_to_ns(
4020 struct usb_endpoint_descriptor *desc)
4021{
4022 return (1 << (desc->bInterval - 1)) * 125 * 1000;
4023}
4024
4025static u16 xhci_get_timeout_no_hub_lpm(struct usb_device *udev,
4026 enum usb3_link_state state)
4027{
4028 unsigned long long sel;
4029 unsigned long long pel;
4030 unsigned int max_sel_pel;
4031 char *state_name;
4032
4033 switch (state) {
4034 case USB3_LPM_U1:
4035 /* Convert SEL and PEL stored in nanoseconds to microseconds */
4036 sel = DIV_ROUND_UP(udev->u1_params.sel, 1000);
4037 pel = DIV_ROUND_UP(udev->u1_params.pel, 1000);
4038 max_sel_pel = USB3_LPM_MAX_U1_SEL_PEL;
4039 state_name = "U1";
4040 break;
4041 case USB3_LPM_U2:
4042 sel = DIV_ROUND_UP(udev->u2_params.sel, 1000);
4043 pel = DIV_ROUND_UP(udev->u2_params.pel, 1000);
4044 max_sel_pel = USB3_LPM_MAX_U2_SEL_PEL;
4045 state_name = "U2";
4046 break;
4047 default:
4048 dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
4049 __func__);
4050 return USB3_LPM_DISABLED;
4051 }
4052
4053 if (sel <= max_sel_pel && pel <= max_sel_pel)
4054 return USB3_LPM_DEVICE_INITIATED;
4055
4056 if (sel > max_sel_pel)
4057 dev_dbg(&udev->dev, "Device-initiated %s disabled "
4058 "due to long SEL %llu ms\n",
4059 state_name, sel);
4060 else
4061 dev_dbg(&udev->dev, "Device-initiated %s disabled "
4062 "due to long PEL %llu\n ms",
4063 state_name, pel);
4064 return USB3_LPM_DISABLED;
4065}
4066
4067/* Returns the hub-encoded U1 timeout value.
4068 * The U1 timeout should be the maximum of the following values:
4069 * - For control endpoints, U1 system exit latency (SEL) * 3
4070 * - For bulk endpoints, U1 SEL * 5
4071 * - For interrupt endpoints:
4072 * - Notification EPs, U1 SEL * 3
4073 * - Periodic EPs, max(105% of bInterval, U1 SEL * 2)
4074 * - For isochronous endpoints, max(105% of bInterval, U1 SEL * 2)
4075 */
4076static u16 xhci_calculate_intel_u1_timeout(struct usb_device *udev,
4077 struct usb_endpoint_descriptor *desc)
4078{
4079 unsigned long long timeout_ns;
4080 int ep_type;
4081 int intr_type;
4082
4083 ep_type = usb_endpoint_type(desc);
4084 switch (ep_type) {
4085 case USB_ENDPOINT_XFER_CONTROL:
4086 timeout_ns = udev->u1_params.sel * 3;
4087 break;
4088 case USB_ENDPOINT_XFER_BULK:
4089 timeout_ns = udev->u1_params.sel * 5;
4090 break;
4091 case USB_ENDPOINT_XFER_INT:
4092 intr_type = usb_endpoint_interrupt_type(desc);
4093 if (intr_type == USB_ENDPOINT_INTR_NOTIFICATION) {
4094 timeout_ns = udev->u1_params.sel * 3;
4095 break;
4096 }
4097 /* Otherwise the calculation is the same as isoc eps */
4098 case USB_ENDPOINT_XFER_ISOC:
4099 timeout_ns = xhci_service_interval_to_ns(desc);
4100 timeout_ns = DIV_ROUND_UP_ULL(timeout_ns * 105, 100);
4101 if (timeout_ns < udev->u1_params.sel * 2)
4102 timeout_ns = udev->u1_params.sel * 2;
4103 break;
4104 default:
4105 return 0;
4106 }
4107
4108 /* The U1 timeout is encoded in 1us intervals. */
4109 timeout_ns = DIV_ROUND_UP_ULL(timeout_ns, 1000);
4110 /* Don't return a timeout of zero, because that's USB3_LPM_DISABLED. */
4111 if (timeout_ns == USB3_LPM_DISABLED)
4112 timeout_ns++;
4113
4114 /* If the necessary timeout value is bigger than what we can set in the
4115 * USB 3.0 hub, we have to disable hub-initiated U1.
4116 */
4117 if (timeout_ns <= USB3_LPM_U1_MAX_TIMEOUT)
4118 return timeout_ns;
4119 dev_dbg(&udev->dev, "Hub-initiated U1 disabled "
4120 "due to long timeout %llu ms\n", timeout_ns);
4121 return xhci_get_timeout_no_hub_lpm(udev, USB3_LPM_U1);
4122}
4123
4124/* Returns the hub-encoded U2 timeout value.
4125 * The U2 timeout should be the maximum of:
4126 * - 10 ms (to avoid the bandwidth impact on the scheduler)
4127 * - largest bInterval of any active periodic endpoint (to avoid going
4128 * into lower power link states between intervals).
4129 * - the U2 Exit Latency of the device
4130 */
4131static u16 xhci_calculate_intel_u2_timeout(struct usb_device *udev,
4132 struct usb_endpoint_descriptor *desc)
4133{
4134 unsigned long long timeout_ns;
4135 unsigned long long u2_del_ns;
4136
4137 timeout_ns = 10 * 1000 * 1000;
4138
4139 if ((usb_endpoint_xfer_int(desc) || usb_endpoint_xfer_isoc(desc)) &&
4140 (xhci_service_interval_to_ns(desc) > timeout_ns))
4141 timeout_ns = xhci_service_interval_to_ns(desc);
4142
4143 u2_del_ns = udev->bos->ss_cap->bU2DevExitLat * 1000;
4144 if (u2_del_ns > timeout_ns)
4145 timeout_ns = u2_del_ns;
4146
4147 /* The U2 timeout is encoded in 256us intervals */
4148 timeout_ns = DIV_ROUND_UP_ULL(timeout_ns, 256 * 1000);
4149 /* If the necessary timeout value is bigger than what we can set in the
4150 * USB 3.0 hub, we have to disable hub-initiated U2.
4151 */
4152 if (timeout_ns <= USB3_LPM_U2_MAX_TIMEOUT)
4153 return timeout_ns;
4154 dev_dbg(&udev->dev, "Hub-initiated U2 disabled "
4155 "due to long timeout %llu ms\n", timeout_ns);
4156 return xhci_get_timeout_no_hub_lpm(udev, USB3_LPM_U2);
4157}
4158
4159static u16 xhci_call_host_update_timeout_for_endpoint(struct xhci_hcd *xhci,
4160 struct usb_device *udev,
4161 struct usb_endpoint_descriptor *desc,
4162 enum usb3_link_state state,
4163 u16 *timeout)
4164{
4165 if (state == USB3_LPM_U1) {
4166 if (xhci->quirks & XHCI_INTEL_HOST)
4167 return xhci_calculate_intel_u1_timeout(udev, desc);
4168 } else {
4169 if (xhci->quirks & XHCI_INTEL_HOST)
4170 return xhci_calculate_intel_u2_timeout(udev, desc);
4171 }
4172
4173 return USB3_LPM_DISABLED;
4174}
4175
4176static int xhci_update_timeout_for_endpoint(struct xhci_hcd *xhci,
4177 struct usb_device *udev,
4178 struct usb_endpoint_descriptor *desc,
4179 enum usb3_link_state state,
4180 u16 *timeout)
4181{
4182 u16 alt_timeout;
4183
4184 alt_timeout = xhci_call_host_update_timeout_for_endpoint(xhci, udev,
4185 desc, state, timeout);
4186
4187 /* If we found we can't enable hub-initiated LPM, or
4188 * the U1 or U2 exit latency was too high to allow
4189 * device-initiated LPM as well, just stop searching.
4190 */
4191 if (alt_timeout == USB3_LPM_DISABLED ||
4192 alt_timeout == USB3_LPM_DEVICE_INITIATED) {
4193 *timeout = alt_timeout;
4194 return -E2BIG;
4195 }
4196 if (alt_timeout > *timeout)
4197 *timeout = alt_timeout;
4198 return 0;
4199}
4200
4201static int xhci_update_timeout_for_interface(struct xhci_hcd *xhci,
4202 struct usb_device *udev,
4203 struct usb_host_interface *alt,
4204 enum usb3_link_state state,
4205 u16 *timeout)
4206{
4207 int j;
4208
4209 for (j = 0; j < alt->desc.bNumEndpoints; j++) {
4210 if (xhci_update_timeout_for_endpoint(xhci, udev,
4211 &alt->endpoint[j].desc, state, timeout))
4212 return -E2BIG;
4213 continue;
4214 }
4215 return 0;
4216}
4217
4218static int xhci_check_intel_tier_policy(struct usb_device *udev,
4219 enum usb3_link_state state)
4220{
4221 struct usb_device *parent;
4222 unsigned int num_hubs;
4223
4224 if (state == USB3_LPM_U2)
4225 return 0;
4226
4227 /* Don't enable U1 if the device is on a 2nd tier hub or lower. */
4228 for (parent = udev->parent, num_hubs = 0; parent->parent;
4229 parent = parent->parent)
4230 num_hubs++;
4231
4232 if (num_hubs < 2)
4233 return 0;
4234
4235 dev_dbg(&udev->dev, "Disabling U1 link state for device"
4236 " below second-tier hub.\n");
4237 dev_dbg(&udev->dev, "Plug device into first-tier hub "
4238 "to decrease power consumption.\n");
4239 return -E2BIG;
4240}
4241
4242static int xhci_check_tier_policy(struct xhci_hcd *xhci,
4243 struct usb_device *udev,
4244 enum usb3_link_state state)
4245{
4246 if (xhci->quirks & XHCI_INTEL_HOST)
4247 return xhci_check_intel_tier_policy(udev, state);
4248 return -EINVAL;
4249}
4250
4251/* Returns the U1 or U2 timeout that should be enabled.
4252 * If the tier check or timeout setting functions return with a non-zero exit
4253 * code, that means the timeout value has been finalized and we shouldn't look
4254 * at any more endpoints.
4255 */
4256static u16 xhci_calculate_lpm_timeout(struct usb_hcd *hcd,
4257 struct usb_device *udev, enum usb3_link_state state)
4258{
4259 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4260 struct usb_host_config *config;
4261 char *state_name;
4262 int i;
4263 u16 timeout = USB3_LPM_DISABLED;
4264
4265 if (state == USB3_LPM_U1)
4266 state_name = "U1";
4267 else if (state == USB3_LPM_U2)
4268 state_name = "U2";
4269 else {
4270 dev_warn(&udev->dev, "Can't enable unknown link state %i\n",
4271 state);
4272 return timeout;
4273 }
4274
4275 if (xhci_check_tier_policy(xhci, udev, state) < 0)
4276 return timeout;
4277
4278 /* Gather some information about the currently installed configuration
4279 * and alternate interface settings.
4280 */
4281 if (xhci_update_timeout_for_endpoint(xhci, udev, &udev->ep0.desc,
4282 state, &timeout))
4283 return timeout;
4284
4285 config = udev->actconfig;
4286 if (!config)
4287 return timeout;
4288
4289 for (i = 0; i < USB_MAXINTERFACES; i++) {
4290 struct usb_driver *driver;
4291 struct usb_interface *intf = config->interface[i];
4292
4293 if (!intf)
4294 continue;
4295
4296 /* Check if any currently bound drivers want hub-initiated LPM
4297 * disabled.
4298 */
4299 if (intf->dev.driver) {
4300 driver = to_usb_driver(intf->dev.driver);
4301 if (driver && driver->disable_hub_initiated_lpm) {
4302 dev_dbg(&udev->dev, "Hub-initiated %s disabled "
4303 "at request of driver %s\n",
4304 state_name, driver->name);
4305 return xhci_get_timeout_no_hub_lpm(udev, state);
4306 }
4307 }
4308
4309 /* Not sure how this could happen... */
4310 if (!intf->cur_altsetting)
4311 continue;
4312
4313 if (xhci_update_timeout_for_interface(xhci, udev,
4314 intf->cur_altsetting,
4315 state, &timeout))
4316 return timeout;
4317 }
4318 return timeout;
4319}
4320
4321/*
4322 * Issue an Evaluate Context command to change the Maximum Exit Latency in the
4323 * slot context. If that succeeds, store the new MEL in the xhci_virt_device.
4324 */
4325static int xhci_change_max_exit_latency(struct xhci_hcd *xhci,
4326 struct usb_device *udev, u16 max_exit_latency)
4327{
4328 struct xhci_virt_device *virt_dev;
4329 struct xhci_command *command;
4330 struct xhci_input_control_ctx *ctrl_ctx;
4331 struct xhci_slot_ctx *slot_ctx;
4332 unsigned long flags;
4333 int ret;
4334
4335 spin_lock_irqsave(&xhci->lock, flags);
4336 if (max_exit_latency == xhci->devs[udev->slot_id]->current_mel) {
4337 spin_unlock_irqrestore(&xhci->lock, flags);
4338 return 0;
4339 }
4340
4341 /* Attempt to issue an Evaluate Context command to change the MEL. */
4342 virt_dev = xhci->devs[udev->slot_id];
4343 command = xhci->lpm_command;
4344 xhci_slot_copy(xhci, command->in_ctx, virt_dev->out_ctx);
4345 spin_unlock_irqrestore(&xhci->lock, flags);
4346
4347 ctrl_ctx = xhci_get_input_control_ctx(xhci, command->in_ctx);
4348 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
4349 slot_ctx = xhci_get_slot_ctx(xhci, command->in_ctx);
4350 slot_ctx->dev_info2 &= cpu_to_le32(~((u32) MAX_EXIT));
4351 slot_ctx->dev_info2 |= cpu_to_le32(max_exit_latency);
4352
4353 xhci_dbg(xhci, "Set up evaluate context for LPM MEL change.\n");
4354 xhci_dbg(xhci, "Slot %u Input Context:\n", udev->slot_id);
4355 xhci_dbg_ctx(xhci, command->in_ctx, 0);
4356
4357 /* Issue and wait for the evaluate context command. */
4358 ret = xhci_configure_endpoint(xhci, udev, command,
4359 true, true);
4360 xhci_dbg(xhci, "Slot %u Output Context:\n", udev->slot_id);
4361 xhci_dbg_ctx(xhci, virt_dev->out_ctx, 0);
4362
4363 if (!ret) {
4364 spin_lock_irqsave(&xhci->lock, flags);
4365 virt_dev->current_mel = max_exit_latency;
4366 spin_unlock_irqrestore(&xhci->lock, flags);
4367 }
4368 return ret;
4369}
4370
4371static int calculate_max_exit_latency(struct usb_device *udev,
4372 enum usb3_link_state state_changed,
4373 u16 hub_encoded_timeout)
4374{
4375 unsigned long long u1_mel_us = 0;
4376 unsigned long long u2_mel_us = 0;
4377 unsigned long long mel_us = 0;
4378 bool disabling_u1;
4379 bool disabling_u2;
4380 bool enabling_u1;
4381 bool enabling_u2;
4382
4383 disabling_u1 = (state_changed == USB3_LPM_U1 &&
4384 hub_encoded_timeout == USB3_LPM_DISABLED);
4385 disabling_u2 = (state_changed == USB3_LPM_U2 &&
4386 hub_encoded_timeout == USB3_LPM_DISABLED);
4387
4388 enabling_u1 = (state_changed == USB3_LPM_U1 &&
4389 hub_encoded_timeout != USB3_LPM_DISABLED);
4390 enabling_u2 = (state_changed == USB3_LPM_U2 &&
4391 hub_encoded_timeout != USB3_LPM_DISABLED);
4392
4393 /* If U1 was already enabled and we're not disabling it,
4394 * or we're going to enable U1, account for the U1 max exit latency.
4395 */
4396 if ((udev->u1_params.timeout != USB3_LPM_DISABLED && !disabling_u1) ||
4397 enabling_u1)
4398 u1_mel_us = DIV_ROUND_UP(udev->u1_params.mel, 1000);
4399 if ((udev->u2_params.timeout != USB3_LPM_DISABLED && !disabling_u2) ||
4400 enabling_u2)
4401 u2_mel_us = DIV_ROUND_UP(udev->u2_params.mel, 1000);
4402
4403 if (u1_mel_us > u2_mel_us)
4404 mel_us = u1_mel_us;
4405 else
4406 mel_us = u2_mel_us;
4407 /* xHCI host controller max exit latency field is only 16 bits wide. */
4408 if (mel_us > MAX_EXIT) {
4409 dev_warn(&udev->dev, "Link PM max exit latency of %lluus "
4410 "is too big.\n", mel_us);
4411 return -E2BIG;
4412 }
4413 return mel_us;
4414}
4415
4416/* Returns the USB3 hub-encoded value for the U1/U2 timeout. */
4417int xhci_enable_usb3_lpm_timeout(struct usb_hcd *hcd,
4418 struct usb_device *udev, enum usb3_link_state state)
4419{
4420 struct xhci_hcd *xhci;
4421 u16 hub_encoded_timeout;
4422 int mel;
4423 int ret;
4424
4425 xhci = hcd_to_xhci(hcd);
4426 /* The LPM timeout values are pretty host-controller specific, so don't
4427 * enable hub-initiated timeouts unless the vendor has provided
4428 * information about their timeout algorithm.
4429 */
4430 if (!xhci || !(xhci->quirks & XHCI_LPM_SUPPORT) ||
4431 !xhci->devs[udev->slot_id])
4432 return USB3_LPM_DISABLED;
4433
4434 hub_encoded_timeout = xhci_calculate_lpm_timeout(hcd, udev, state);
4435 mel = calculate_max_exit_latency(udev, state, hub_encoded_timeout);
4436 if (mel < 0) {
4437 /* Max Exit Latency is too big, disable LPM. */
4438 hub_encoded_timeout = USB3_LPM_DISABLED;
4439 mel = 0;
4440 }
4441
4442 ret = xhci_change_max_exit_latency(xhci, udev, mel);
4443 if (ret)
4444 return ret;
4445 return hub_encoded_timeout;
4446}
4447
4448int xhci_disable_usb3_lpm_timeout(struct usb_hcd *hcd,
4449 struct usb_device *udev, enum usb3_link_state state)
4450{
4451 struct xhci_hcd *xhci;
4452 u16 mel;
4453 int ret;
4454
4455 xhci = hcd_to_xhci(hcd);
4456 if (!xhci || !(xhci->quirks & XHCI_LPM_SUPPORT) ||
4457 !xhci->devs[udev->slot_id])
4458 return 0;
4459
4460 mel = calculate_max_exit_latency(udev, state, USB3_LPM_DISABLED);
4461 ret = xhci_change_max_exit_latency(xhci, udev, mel);
4462 if (ret)
4463 return ret;
4464 return 0;
4465}
4466#else /* CONFIG_PM */
4467
4468int xhci_enable_usb3_lpm_timeout(struct usb_hcd *hcd,
4469 struct usb_device *udev, enum usb3_link_state state)
4470{
4471 return USB3_LPM_DISABLED;
4472}
4473
4474int xhci_disable_usb3_lpm_timeout(struct usb_hcd *hcd,
4475 struct usb_device *udev, enum usb3_link_state state)
4476{
4477 return 0;
4478}
4479#endif /* CONFIG_PM */
4480
4481/*-------------------------------------------------------------------------*/
4482
4483/* Once a hub descriptor is fetched for a device, we need to update the xHC's
4484 * internal data structures for the device.
4485 */
4486int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev,
4487 struct usb_tt *tt, gfp_t mem_flags)
4488{
4489 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4490 struct xhci_virt_device *vdev;
4491 struct xhci_command *config_cmd;
4492 struct xhci_input_control_ctx *ctrl_ctx;
4493 struct xhci_slot_ctx *slot_ctx;
4494 unsigned long flags;
4495 unsigned think_time;
4496 int ret;
4497
4498 /* Ignore root hubs */
4499 if (!hdev->parent)
4500 return 0;
4501
4502 vdev = xhci->devs[hdev->slot_id];
4503 if (!vdev) {
4504 xhci_warn(xhci, "Cannot update hub desc for unknown device.\n");
4505 return -EINVAL;
4506 }
4507 config_cmd = xhci_alloc_command(xhci, true, true, mem_flags);
4508 if (!config_cmd) {
4509 xhci_dbg(xhci, "Could not allocate xHCI command structure.\n");
4510 return -ENOMEM;
4511 }
4512
4513 spin_lock_irqsave(&xhci->lock, flags);
4514 if (hdev->speed == USB_SPEED_HIGH &&
4515 xhci_alloc_tt_info(xhci, vdev, hdev, tt, GFP_ATOMIC)) {
4516 xhci_dbg(xhci, "Could not allocate xHCI TT structure.\n");
4517 xhci_free_command(xhci, config_cmd);
4518 spin_unlock_irqrestore(&xhci->lock, flags);
4519 return -ENOMEM;
4520 }
4521
4522 xhci_slot_copy(xhci, config_cmd->in_ctx, vdev->out_ctx);
4523 ctrl_ctx = xhci_get_input_control_ctx(xhci, config_cmd->in_ctx);
4524 ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
4525 slot_ctx = xhci_get_slot_ctx(xhci, config_cmd->in_ctx);
4526 slot_ctx->dev_info |= cpu_to_le32(DEV_HUB);
4527 if (tt->multi)
4528 slot_ctx->dev_info |= cpu_to_le32(DEV_MTT);
4529 if (xhci->hci_version > 0x95) {
4530 xhci_dbg(xhci, "xHCI version %x needs hub "
4531 "TT think time and number of ports\n",
4532 (unsigned int) xhci->hci_version);
4533 slot_ctx->dev_info2 |= cpu_to_le32(XHCI_MAX_PORTS(hdev->maxchild));
4534 /* Set TT think time - convert from ns to FS bit times.
4535 * 0 = 8 FS bit times, 1 = 16 FS bit times,
4536 * 2 = 24 FS bit times, 3 = 32 FS bit times.
4537 *
4538 * xHCI 1.0: this field shall be 0 if the device is not a
4539 * High-spped hub.
4540 */
4541 think_time = tt->think_time;
4542 if (think_time != 0)
4543 think_time = (think_time / 666) - 1;
4544 if (xhci->hci_version < 0x100 || hdev->speed == USB_SPEED_HIGH)
4545 slot_ctx->tt_info |=
4546 cpu_to_le32(TT_THINK_TIME(think_time));
4547 } else {
4548 xhci_dbg(xhci, "xHCI version %x doesn't need hub "
4549 "TT think time or number of ports\n",
4550 (unsigned int) xhci->hci_version);
4551 }
4552 slot_ctx->dev_state = 0;
4553 spin_unlock_irqrestore(&xhci->lock, flags);
4554
4555 xhci_dbg(xhci, "Set up %s for hub device.\n",
4556 (xhci->hci_version > 0x95) ?
4557 "configure endpoint" : "evaluate context");
4558 xhci_dbg(xhci, "Slot %u Input Context:\n", hdev->slot_id);
4559 xhci_dbg_ctx(xhci, config_cmd->in_ctx, 0);
4560
4561 /* Issue and wait for the configure endpoint or
4562 * evaluate context command.
4563 */
4564 if (xhci->hci_version > 0x95)
4565 ret = xhci_configure_endpoint(xhci, hdev, config_cmd,
4566 false, false);
4567 else
4568 ret = xhci_configure_endpoint(xhci, hdev, config_cmd,
4569 true, false);
4570
4571 xhci_dbg(xhci, "Slot %u Output Context:\n", hdev->slot_id);
4572 xhci_dbg_ctx(xhci, vdev->out_ctx, 0);
4573
4574 xhci_free_command(xhci, config_cmd);
4575 return ret;
4576}
4577
4578int xhci_get_frame(struct usb_hcd *hcd)
4579{
4580 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
4581 /* EHCI mods by the periodic size. Why? */
4582 return xhci_readl(xhci, &xhci->run_regs->microframe_index) >> 3;
4583}
4584
4585int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks)
4586{
4587 struct xhci_hcd *xhci;
4588 struct device *dev = hcd->self.controller;
4589 int retval;
4590 u32 temp;
4591
4592 /* Accept arbitrarily long scatter-gather lists */
4593 hcd->self.sg_tablesize = ~0;
4594
4595 if (usb_hcd_is_primary_hcd(hcd)) {
4596 xhci = kzalloc(sizeof(struct xhci_hcd), GFP_KERNEL);
4597 if (!xhci)
4598 return -ENOMEM;
4599 *((struct xhci_hcd **) hcd->hcd_priv) = xhci;
4600 xhci->main_hcd = hcd;
4601 /* Mark the first roothub as being USB 2.0.
4602 * The xHCI driver will register the USB 3.0 roothub.
4603 */
4604 hcd->speed = HCD_USB2;
4605 hcd->self.root_hub->speed = USB_SPEED_HIGH;
4606 /*
4607 * USB 2.0 roothub under xHCI has an integrated TT,
4608 * (rate matching hub) as opposed to having an OHCI/UHCI
4609 * companion controller.
4610 */
4611 hcd->has_tt = 1;
4612 } else {
4613 /* xHCI private pointer was set in xhci_pci_probe for the second
4614 * registered roothub.
4615 */
4616 xhci = hcd_to_xhci(hcd);
4617 temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
4618 if (HCC_64BIT_ADDR(temp)) {
4619 xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
4620 dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64));
4621 } else {
4622 dma_set_mask(hcd->self.controller, DMA_BIT_MASK(32));
4623 }
4624 return 0;
4625 }
4626
4627 xhci->cap_regs = hcd->regs;
4628 xhci->op_regs = hcd->regs +
4629 HC_LENGTH(xhci_readl(xhci, &xhci->cap_regs->hc_capbase));
4630 xhci->run_regs = hcd->regs +
4631 (xhci_readl(xhci, &xhci->cap_regs->run_regs_off) & RTSOFF_MASK);
4632 /* Cache read-only capability registers */
4633 xhci->hcs_params1 = xhci_readl(xhci, &xhci->cap_regs->hcs_params1);
4634 xhci->hcs_params2 = xhci_readl(xhci, &xhci->cap_regs->hcs_params2);
4635 xhci->hcs_params3 = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
4636 xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hc_capbase);
4637 xhci->hci_version = HC_VERSION(xhci->hcc_params);
4638 xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
4639 xhci_print_registers(xhci);
4640
4641 get_quirks(dev, xhci);
4642
4643 /* Make sure the HC is halted. */
4644 retval = xhci_halt(xhci);
4645 if (retval)
4646 goto error;
4647
4648 xhci_dbg(xhci, "Resetting HCD\n");
4649 /* Reset the internal HC memory state and registers. */
4650 retval = xhci_reset(xhci);
4651 if (retval)
4652 goto error;
4653 xhci_dbg(xhci, "Reset complete\n");
4654
4655 temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
4656 if (HCC_64BIT_ADDR(temp)) {
4657 xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
4658 dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64));
4659 } else {
4660 dma_set_mask(hcd->self.controller, DMA_BIT_MASK(32));
4661 }
4662
4663 xhci_dbg(xhci, "Calling HCD init\n");
4664 /* Initialize HCD and host controller data structures. */
4665 retval = xhci_init(hcd);
4666 if (retval)
4667 goto error;
4668 xhci_dbg(xhci, "Called HCD init\n");
4669 return 0;
4670error:
4671 kfree(xhci);
4672 return retval;
4673}
4674
4675MODULE_DESCRIPTION(DRIVER_DESC);
4676MODULE_AUTHOR(DRIVER_AUTHOR);
4677MODULE_LICENSE("GPL");
4678
4679static int __init xhci_hcd_init(void)
4680{
4681 int retval;
4682
4683 retval = xhci_register_pci();
4684 if (retval < 0) {
4685 printk(KERN_DEBUG "Problem registering PCI driver.");
4686 return retval;
4687 }
4688 retval = xhci_register_plat();
4689 if (retval < 0) {
4690 printk(KERN_DEBUG "Problem registering platform driver.");
4691 goto unreg_pci;
4692 }
4693 /*
4694 * Check the compiler generated sizes of structures that must be laid
4695 * out in specific ways for hardware access.
4696 */
4697 BUILD_BUG_ON(sizeof(struct xhci_doorbell_array) != 256*32/8);
4698 BUILD_BUG_ON(sizeof(struct xhci_slot_ctx) != 8*32/8);
4699 BUILD_BUG_ON(sizeof(struct xhci_ep_ctx) != 8*32/8);
4700 /* xhci_device_control has eight fields, and also
4701 * embeds one xhci_slot_ctx and 31 xhci_ep_ctx
4702 */
4703 BUILD_BUG_ON(sizeof(struct xhci_stream_ctx) != 4*32/8);
4704 BUILD_BUG_ON(sizeof(union xhci_trb) != 4*32/8);
4705 BUILD_BUG_ON(sizeof(struct xhci_erst_entry) != 4*32/8);
4706 BUILD_BUG_ON(sizeof(struct xhci_cap_regs) != 7*32/8);
4707 BUILD_BUG_ON(sizeof(struct xhci_intr_reg) != 8*32/8);
4708 /* xhci_run_regs has eight fields and embeds 128 xhci_intr_regs */
4709 BUILD_BUG_ON(sizeof(struct xhci_run_regs) != (8+8*128)*32/8);
4710 return 0;
4711unreg_pci:
4712 xhci_unregister_pci();
4713 return retval;
4714}
4715module_init(xhci_hcd_init);
4716
4717static void __exit xhci_hcd_cleanup(void)
4718{
4719 xhci_unregister_pci();
4720 xhci_unregister_plat();
4721}
4722module_exit(xhci_hcd_cleanup);