Loading...
1/*
2 * An SPI driver for the Philips PCF2123 RTC
3 * Copyright 2009 Cyber Switching, Inc.
4 *
5 * Author: Chris Verges <chrisv@cyberswitching.com>
6 * Maintainers: http://www.cyberswitching.com
7 *
8 * based on the RS5C348 driver in this same directory.
9 *
10 * Thanks to Christian Pellegrin <chripell@fsfe.org> for
11 * the sysfs contributions to this driver.
12 *
13 * This program is free software; you can redistribute it and/or modify
14 * it under the terms of the GNU General Public License version 2 as
15 * published by the Free Software Foundation.
16 *
17 * Please note that the CS is active high, so platform data
18 * should look something like:
19 *
20 * static struct spi_board_info ek_spi_devices[] = {
21 * ...
22 * {
23 * .modalias = "rtc-pcf2123",
24 * .chip_select = 1,
25 * .controller_data = (void *)AT91_PIN_PA10,
26 * .max_speed_hz = 1000 * 1000,
27 * .mode = SPI_CS_HIGH,
28 * .bus_num = 0,
29 * },
30 * ...
31 *};
32 *
33 */
34
35#include <linux/bcd.h>
36#include <linux/delay.h>
37#include <linux/device.h>
38#include <linux/errno.h>
39#include <linux/init.h>
40#include <linux/kernel.h>
41#include <linux/of.h>
42#include <linux/string.h>
43#include <linux/slab.h>
44#include <linux/rtc.h>
45#include <linux/spi/spi.h>
46#include <linux/module.h>
47#include <linux/sysfs.h>
48
49#define DRV_VERSION "0.6"
50
51/* REGISTERS */
52#define PCF2123_REG_CTRL1 (0x00) /* Control Register 1 */
53#define PCF2123_REG_CTRL2 (0x01) /* Control Register 2 */
54#define PCF2123_REG_SC (0x02) /* datetime */
55#define PCF2123_REG_MN (0x03)
56#define PCF2123_REG_HR (0x04)
57#define PCF2123_REG_DM (0x05)
58#define PCF2123_REG_DW (0x06)
59#define PCF2123_REG_MO (0x07)
60#define PCF2123_REG_YR (0x08)
61#define PCF2123_REG_ALRM_MN (0x09) /* Alarm Registers */
62#define PCF2123_REG_ALRM_HR (0x0a)
63#define PCF2123_REG_ALRM_DM (0x0b)
64#define PCF2123_REG_ALRM_DW (0x0c)
65#define PCF2123_REG_OFFSET (0x0d) /* Clock Rate Offset Register */
66#define PCF2123_REG_TMR_CLKOUT (0x0e) /* Timer Registers */
67#define PCF2123_REG_CTDWN_TMR (0x0f)
68
69/* PCF2123_REG_CTRL1 BITS */
70#define CTRL1_CLEAR (0) /* Clear */
71#define CTRL1_CORR_INT BIT(1) /* Correction irq enable */
72#define CTRL1_12_HOUR BIT(2) /* 12 hour time */
73#define CTRL1_SW_RESET (BIT(3) | BIT(4) | BIT(6)) /* Software reset */
74#define CTRL1_STOP BIT(5) /* Stop the clock */
75#define CTRL1_EXT_TEST BIT(7) /* External clock test mode */
76
77/* PCF2123_REG_CTRL2 BITS */
78#define CTRL2_TIE BIT(0) /* Countdown timer irq enable */
79#define CTRL2_AIE BIT(1) /* Alarm irq enable */
80#define CTRL2_TF BIT(2) /* Countdown timer flag */
81#define CTRL2_AF BIT(3) /* Alarm flag */
82#define CTRL2_TI_TP BIT(4) /* Irq pin generates pulse */
83#define CTRL2_MSF BIT(5) /* Minute or second irq flag */
84#define CTRL2_SI BIT(6) /* Second irq enable */
85#define CTRL2_MI BIT(7) /* Minute irq enable */
86
87/* PCF2123_REG_SC BITS */
88#define OSC_HAS_STOPPED BIT(7) /* Clock has been stopped */
89
90/* PCF2123_REG_ALRM_XX BITS */
91#define ALRM_ENABLE BIT(7) /* MN, HR, DM, or DW alarm enable */
92
93/* PCF2123_REG_TMR_CLKOUT BITS */
94#define CD_TMR_4096KHZ (0) /* 4096 KHz countdown timer */
95#define CD_TMR_64HZ (1) /* 64 Hz countdown timer */
96#define CD_TMR_1HZ (2) /* 1 Hz countdown timer */
97#define CD_TMR_60th_HZ (3) /* 60th Hz countdown timer */
98#define CD_TMR_TE BIT(3) /* Countdown timer enable */
99
100/* PCF2123_REG_OFFSET BITS */
101#define OFFSET_SIGN_BIT BIT(6) /* 2's complement sign bit */
102#define OFFSET_COARSE BIT(7) /* Coarse mode offset */
103#define OFFSET_STEP (2170) /* Offset step in parts per billion */
104
105/* READ/WRITE ADDRESS BITS */
106#define PCF2123_WRITE BIT(4)
107#define PCF2123_READ (BIT(4) | BIT(7))
108
109
110static struct spi_driver pcf2123_driver;
111
112struct pcf2123_sysfs_reg {
113 struct device_attribute attr;
114 char name[2];
115};
116
117struct pcf2123_plat_data {
118 struct rtc_device *rtc;
119 struct pcf2123_sysfs_reg regs[16];
120};
121
122/*
123 * Causes a 30 nanosecond delay to ensure that the PCF2123 chip select
124 * is released properly after an SPI write. This function should be
125 * called after EVERY read/write call over SPI.
126 */
127static inline void pcf2123_delay_trec(void)
128{
129 ndelay(30);
130}
131
132static int pcf2123_read(struct device *dev, u8 reg, u8 *rxbuf, size_t size)
133{
134 struct spi_device *spi = to_spi_device(dev);
135 int ret;
136
137 reg |= PCF2123_READ;
138 ret = spi_write_then_read(spi, ®, 1, rxbuf, size);
139 pcf2123_delay_trec();
140
141 return ret;
142}
143
144static int pcf2123_write(struct device *dev, u8 *txbuf, size_t size)
145{
146 struct spi_device *spi = to_spi_device(dev);
147 int ret;
148
149 txbuf[0] |= PCF2123_WRITE;
150 ret = spi_write(spi, txbuf, size);
151 pcf2123_delay_trec();
152
153 return ret;
154}
155
156static int pcf2123_write_reg(struct device *dev, u8 reg, u8 val)
157{
158 u8 txbuf[2];
159
160 txbuf[0] = reg;
161 txbuf[1] = val;
162 return pcf2123_write(dev, txbuf, sizeof(txbuf));
163}
164
165static ssize_t pcf2123_show(struct device *dev, struct device_attribute *attr,
166 char *buffer)
167{
168 struct pcf2123_sysfs_reg *r;
169 u8 rxbuf[1];
170 unsigned long reg;
171 int ret;
172
173 r = container_of(attr, struct pcf2123_sysfs_reg, attr);
174
175 ret = kstrtoul(r->name, 16, ®);
176 if (ret)
177 return ret;
178
179 ret = pcf2123_read(dev, reg, rxbuf, 1);
180 if (ret < 0)
181 return -EIO;
182
183 return sprintf(buffer, "0x%x\n", rxbuf[0]);
184}
185
186static ssize_t pcf2123_store(struct device *dev, struct device_attribute *attr,
187 const char *buffer, size_t count) {
188 struct pcf2123_sysfs_reg *r;
189 unsigned long reg;
190 unsigned long val;
191
192 int ret;
193
194 r = container_of(attr, struct pcf2123_sysfs_reg, attr);
195
196 ret = kstrtoul(r->name, 16, ®);
197 if (ret)
198 return ret;
199
200 ret = kstrtoul(buffer, 10, &val);
201 if (ret)
202 return ret;
203
204 pcf2123_write_reg(dev, reg, val);
205 if (ret < 0)
206 return -EIO;
207 return count;
208}
209
210static int pcf2123_read_offset(struct device *dev, long *offset)
211{
212 int ret;
213 s8 reg;
214
215 ret = pcf2123_read(dev, PCF2123_REG_OFFSET, ®, 1);
216 if (ret < 0)
217 return ret;
218
219 if (reg & OFFSET_COARSE)
220 reg <<= 1; /* multiply by 2 and sign extend */
221 else
222 reg |= (reg & OFFSET_SIGN_BIT) << 1; /* sign extend only */
223
224 *offset = ((long)reg) * OFFSET_STEP;
225
226 return 0;
227}
228
229/*
230 * The offset register is a 7 bit signed value with a coarse bit in bit 7.
231 * The main difference between the two is normal offset adjusts the first
232 * second of n minutes every other hour, with 61, 62 and 63 being shoved
233 * into the 60th minute.
234 * The coarse adjustment does the same, but every hour.
235 * the two overlap, with every even normal offset value corresponding
236 * to a coarse offset. Based on this algorithm, it seems that despite the
237 * name, coarse offset is a better fit for overlapping values.
238 */
239static int pcf2123_set_offset(struct device *dev, long offset)
240{
241 s8 reg;
242
243 if (offset > OFFSET_STEP * 127)
244 reg = 127;
245 else if (offset < OFFSET_STEP * -128)
246 reg = -128;
247 else
248 reg = (s8)((offset + (OFFSET_STEP >> 1)) / OFFSET_STEP);
249
250 /* choose fine offset only for odd values in the normal range */
251 if (reg & 1 && reg <= 63 && reg >= -64) {
252 /* Normal offset. Clear the coarse bit */
253 reg &= ~OFFSET_COARSE;
254 } else {
255 /* Coarse offset. Divide by 2 and set the coarse bit */
256 reg >>= 1;
257 reg |= OFFSET_COARSE;
258 }
259
260 return pcf2123_write_reg(dev, PCF2123_REG_OFFSET, reg);
261}
262
263static int pcf2123_rtc_read_time(struct device *dev, struct rtc_time *tm)
264{
265 u8 rxbuf[7];
266 int ret;
267
268 ret = pcf2123_read(dev, PCF2123_REG_SC, rxbuf, sizeof(rxbuf));
269 if (ret < 0)
270 return ret;
271
272 if (rxbuf[0] & OSC_HAS_STOPPED) {
273 dev_info(dev, "clock was stopped. Time is not valid\n");
274 return -EINVAL;
275 }
276
277 tm->tm_sec = bcd2bin(rxbuf[0] & 0x7F);
278 tm->tm_min = bcd2bin(rxbuf[1] & 0x7F);
279 tm->tm_hour = bcd2bin(rxbuf[2] & 0x3F); /* rtc hr 0-23 */
280 tm->tm_mday = bcd2bin(rxbuf[3] & 0x3F);
281 tm->tm_wday = rxbuf[4] & 0x07;
282 tm->tm_mon = bcd2bin(rxbuf[5] & 0x1F) - 1; /* rtc mn 1-12 */
283 tm->tm_year = bcd2bin(rxbuf[6]);
284 if (tm->tm_year < 70)
285 tm->tm_year += 100; /* assume we are in 1970...2069 */
286
287 dev_dbg(dev, "%s: tm is secs=%d, mins=%d, hours=%d, "
288 "mday=%d, mon=%d, year=%d, wday=%d\n",
289 __func__,
290 tm->tm_sec, tm->tm_min, tm->tm_hour,
291 tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday);
292
293 return rtc_valid_tm(tm);
294}
295
296static int pcf2123_rtc_set_time(struct device *dev, struct rtc_time *tm)
297{
298 u8 txbuf[8];
299 int ret;
300
301 dev_dbg(dev, "%s: tm is secs=%d, mins=%d, hours=%d, "
302 "mday=%d, mon=%d, year=%d, wday=%d\n",
303 __func__,
304 tm->tm_sec, tm->tm_min, tm->tm_hour,
305 tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday);
306
307 /* Stop the counter first */
308 ret = pcf2123_write_reg(dev, PCF2123_REG_CTRL1, CTRL1_STOP);
309 if (ret < 0)
310 return ret;
311
312 /* Set the new time */
313 txbuf[0] = PCF2123_REG_SC;
314 txbuf[1] = bin2bcd(tm->tm_sec & 0x7F);
315 txbuf[2] = bin2bcd(tm->tm_min & 0x7F);
316 txbuf[3] = bin2bcd(tm->tm_hour & 0x3F);
317 txbuf[4] = bin2bcd(tm->tm_mday & 0x3F);
318 txbuf[5] = tm->tm_wday & 0x07;
319 txbuf[6] = bin2bcd((tm->tm_mon + 1) & 0x1F); /* rtc mn 1-12 */
320 txbuf[7] = bin2bcd(tm->tm_year < 100 ? tm->tm_year : tm->tm_year - 100);
321
322 ret = pcf2123_write(dev, txbuf, sizeof(txbuf));
323 if (ret < 0)
324 return ret;
325
326 /* Start the counter */
327 ret = pcf2123_write_reg(dev, PCF2123_REG_CTRL1, CTRL1_CLEAR);
328 if (ret < 0)
329 return ret;
330
331 return 0;
332}
333
334static int pcf2123_reset(struct device *dev)
335{
336 int ret;
337 u8 rxbuf[2];
338
339 ret = pcf2123_write_reg(dev, PCF2123_REG_CTRL1, CTRL1_SW_RESET);
340 if (ret < 0)
341 return ret;
342
343 /* Stop the counter */
344 dev_dbg(dev, "stopping RTC\n");
345 ret = pcf2123_write_reg(dev, PCF2123_REG_CTRL1, CTRL1_STOP);
346 if (ret < 0)
347 return ret;
348
349 /* See if the counter was actually stopped */
350 dev_dbg(dev, "checking for presence of RTC\n");
351 ret = pcf2123_read(dev, PCF2123_REG_CTRL1, rxbuf, sizeof(rxbuf));
352 if (ret < 0)
353 return ret;
354
355 dev_dbg(dev, "received data from RTC (0x%02X 0x%02X)\n",
356 rxbuf[0], rxbuf[1]);
357 if (!(rxbuf[0] & CTRL1_STOP))
358 return -ENODEV;
359
360 /* Start the counter */
361 ret = pcf2123_write_reg(dev, PCF2123_REG_CTRL1, CTRL1_CLEAR);
362 if (ret < 0)
363 return ret;
364
365 return 0;
366}
367
368static const struct rtc_class_ops pcf2123_rtc_ops = {
369 .read_time = pcf2123_rtc_read_time,
370 .set_time = pcf2123_rtc_set_time,
371 .read_offset = pcf2123_read_offset,
372 .set_offset = pcf2123_set_offset,
373
374};
375
376static int pcf2123_probe(struct spi_device *spi)
377{
378 struct rtc_device *rtc;
379 struct rtc_time tm;
380 struct pcf2123_plat_data *pdata;
381 int ret, i;
382
383 pdata = devm_kzalloc(&spi->dev, sizeof(struct pcf2123_plat_data),
384 GFP_KERNEL);
385 if (!pdata)
386 return -ENOMEM;
387 spi->dev.platform_data = pdata;
388
389 ret = pcf2123_rtc_read_time(&spi->dev, &tm);
390 if (ret < 0) {
391 ret = pcf2123_reset(&spi->dev);
392 if (ret < 0) {
393 dev_err(&spi->dev, "chip not found\n");
394 goto kfree_exit;
395 }
396 }
397
398 dev_info(&spi->dev, "chip found, driver version " DRV_VERSION "\n");
399 dev_info(&spi->dev, "spiclk %u KHz.\n",
400 (spi->max_speed_hz + 500) / 1000);
401
402 /* Finalize the initialization */
403 rtc = devm_rtc_device_register(&spi->dev, pcf2123_driver.driver.name,
404 &pcf2123_rtc_ops, THIS_MODULE);
405
406 if (IS_ERR(rtc)) {
407 dev_err(&spi->dev, "failed to register.\n");
408 ret = PTR_ERR(rtc);
409 goto kfree_exit;
410 }
411
412 pdata->rtc = rtc;
413
414 for (i = 0; i < 16; i++) {
415 sysfs_attr_init(&pdata->regs[i].attr.attr);
416 sprintf(pdata->regs[i].name, "%1x", i);
417 pdata->regs[i].attr.attr.mode = S_IRUGO | S_IWUSR;
418 pdata->regs[i].attr.attr.name = pdata->regs[i].name;
419 pdata->regs[i].attr.show = pcf2123_show;
420 pdata->regs[i].attr.store = pcf2123_store;
421 ret = device_create_file(&spi->dev, &pdata->regs[i].attr);
422 if (ret) {
423 dev_err(&spi->dev, "Unable to create sysfs %s\n",
424 pdata->regs[i].name);
425 goto sysfs_exit;
426 }
427 }
428
429 return 0;
430
431sysfs_exit:
432 for (i--; i >= 0; i--)
433 device_remove_file(&spi->dev, &pdata->regs[i].attr);
434
435kfree_exit:
436 spi->dev.platform_data = NULL;
437 return ret;
438}
439
440static int pcf2123_remove(struct spi_device *spi)
441{
442 struct pcf2123_plat_data *pdata = dev_get_platdata(&spi->dev);
443 int i;
444
445 if (pdata) {
446 for (i = 0; i < 16; i++)
447 if (pdata->regs[i].name[0])
448 device_remove_file(&spi->dev,
449 &pdata->regs[i].attr);
450 }
451
452 return 0;
453}
454
455#ifdef CONFIG_OF
456static const struct of_device_id pcf2123_dt_ids[] = {
457 { .compatible = "nxp,rtc-pcf2123", },
458 { /* sentinel */ }
459};
460MODULE_DEVICE_TABLE(of, pcf2123_dt_ids);
461#endif
462
463static struct spi_driver pcf2123_driver = {
464 .driver = {
465 .name = "rtc-pcf2123",
466 .of_match_table = of_match_ptr(pcf2123_dt_ids),
467 },
468 .probe = pcf2123_probe,
469 .remove = pcf2123_remove,
470};
471
472module_spi_driver(pcf2123_driver);
473
474MODULE_AUTHOR("Chris Verges <chrisv@cyberswitching.com>");
475MODULE_DESCRIPTION("NXP PCF2123 RTC driver");
476MODULE_LICENSE("GPL");
477MODULE_VERSION(DRV_VERSION);
1/*
2 * An SPI driver for the Philips PCF2123 RTC
3 * Copyright 2009 Cyber Switching, Inc.
4 *
5 * Author: Chris Verges <chrisv@cyberswitching.com>
6 * Maintainers: http://www.cyberswitching.com
7 *
8 * based on the RS5C348 driver in this same directory.
9 *
10 * Thanks to Christian Pellegrin <chripell@fsfe.org> for
11 * the sysfs contributions to this driver.
12 *
13 * This program is free software; you can redistribute it and/or modify
14 * it under the terms of the GNU General Public License version 2 as
15 * published by the Free Software Foundation.
16 *
17 * Please note that the CS is active high, so platform data
18 * should look something like:
19 *
20 * static struct spi_board_info ek_spi_devices[] = {
21 * ...
22 * {
23 * .modalias = "rtc-pcf2123",
24 * .chip_select = 1,
25 * .controller_data = (void *)AT91_PIN_PA10,
26 * .max_speed_hz = 1000 * 1000,
27 * .mode = SPI_CS_HIGH,
28 * .bus_num = 0,
29 * },
30 * ...
31 *};
32 *
33 */
34
35#include <linux/bcd.h>
36#include <linux/delay.h>
37#include <linux/device.h>
38#include <linux/errno.h>
39#include <linux/init.h>
40#include <linux/kernel.h>
41#include <linux/string.h>
42#include <linux/slab.h>
43#include <linux/rtc.h>
44#include <linux/spi/spi.h>
45
46#define DRV_VERSION "0.6"
47
48#define PCF2123_REG_CTRL1 (0x00) /* Control Register 1 */
49#define PCF2123_REG_CTRL2 (0x01) /* Control Register 2 */
50#define PCF2123_REG_SC (0x02) /* datetime */
51#define PCF2123_REG_MN (0x03)
52#define PCF2123_REG_HR (0x04)
53#define PCF2123_REG_DM (0x05)
54#define PCF2123_REG_DW (0x06)
55#define PCF2123_REG_MO (0x07)
56#define PCF2123_REG_YR (0x08)
57
58#define PCF2123_SUBADDR (1 << 4)
59#define PCF2123_WRITE ((0 << 7) | PCF2123_SUBADDR)
60#define PCF2123_READ ((1 << 7) | PCF2123_SUBADDR)
61
62static struct spi_driver pcf2123_driver;
63
64struct pcf2123_sysfs_reg {
65 struct device_attribute attr;
66 char name[2];
67};
68
69struct pcf2123_plat_data {
70 struct rtc_device *rtc;
71 struct pcf2123_sysfs_reg regs[16];
72};
73
74/*
75 * Causes a 30 nanosecond delay to ensure that the PCF2123 chip select
76 * is released properly after an SPI write. This function should be
77 * called after EVERY read/write call over SPI.
78 */
79static inline void pcf2123_delay_trec(void)
80{
81 ndelay(30);
82}
83
84static ssize_t pcf2123_show(struct device *dev, struct device_attribute *attr,
85 char *buffer)
86{
87 struct spi_device *spi = to_spi_device(dev);
88 struct pcf2123_sysfs_reg *r;
89 u8 txbuf[1], rxbuf[1];
90 unsigned long reg;
91 int ret;
92
93 r = container_of(attr, struct pcf2123_sysfs_reg, attr);
94
95 if (strict_strtoul(r->name, 16, ®))
96 return -EINVAL;
97
98 txbuf[0] = PCF2123_READ | reg;
99 ret = spi_write_then_read(spi, txbuf, 1, rxbuf, 1);
100 if (ret < 0)
101 return -EIO;
102 pcf2123_delay_trec();
103 return sprintf(buffer, "0x%x\n", rxbuf[0]);
104}
105
106static ssize_t pcf2123_store(struct device *dev, struct device_attribute *attr,
107 const char *buffer, size_t count) {
108 struct spi_device *spi = to_spi_device(dev);
109 struct pcf2123_sysfs_reg *r;
110 u8 txbuf[2];
111 unsigned long reg;
112 unsigned long val;
113
114 int ret;
115
116 r = container_of(attr, struct pcf2123_sysfs_reg, attr);
117
118 if (strict_strtoul(r->name, 16, ®)
119 || strict_strtoul(buffer, 10, &val))
120 return -EINVAL;
121
122 txbuf[0] = PCF2123_WRITE | reg;
123 txbuf[1] = val;
124 ret = spi_write(spi, txbuf, sizeof(txbuf));
125 if (ret < 0)
126 return -EIO;
127 pcf2123_delay_trec();
128 return count;
129}
130
131static int pcf2123_rtc_read_time(struct device *dev, struct rtc_time *tm)
132{
133 struct spi_device *spi = to_spi_device(dev);
134 u8 txbuf[1], rxbuf[7];
135 int ret;
136
137 txbuf[0] = PCF2123_READ | PCF2123_REG_SC;
138 ret = spi_write_then_read(spi, txbuf, sizeof(txbuf),
139 rxbuf, sizeof(rxbuf));
140 if (ret < 0)
141 return ret;
142 pcf2123_delay_trec();
143
144 tm->tm_sec = bcd2bin(rxbuf[0] & 0x7F);
145 tm->tm_min = bcd2bin(rxbuf[1] & 0x7F);
146 tm->tm_hour = bcd2bin(rxbuf[2] & 0x3F); /* rtc hr 0-23 */
147 tm->tm_mday = bcd2bin(rxbuf[3] & 0x3F);
148 tm->tm_wday = rxbuf[4] & 0x07;
149 tm->tm_mon = bcd2bin(rxbuf[5] & 0x1F) - 1; /* rtc mn 1-12 */
150 tm->tm_year = bcd2bin(rxbuf[6]);
151 if (tm->tm_year < 70)
152 tm->tm_year += 100; /* assume we are in 1970...2069 */
153
154 dev_dbg(dev, "%s: tm is secs=%d, mins=%d, hours=%d, "
155 "mday=%d, mon=%d, year=%d, wday=%d\n",
156 __func__,
157 tm->tm_sec, tm->tm_min, tm->tm_hour,
158 tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday);
159
160 /* the clock can give out invalid datetime, but we cannot return
161 * -EINVAL otherwise hwclock will refuse to set the time on bootup.
162 */
163 if (rtc_valid_tm(tm) < 0)
164 dev_err(dev, "retrieved date/time is not valid.\n");
165
166 return 0;
167}
168
169static int pcf2123_rtc_set_time(struct device *dev, struct rtc_time *tm)
170{
171 struct spi_device *spi = to_spi_device(dev);
172 u8 txbuf[8];
173 int ret;
174
175 dev_dbg(dev, "%s: tm is secs=%d, mins=%d, hours=%d, "
176 "mday=%d, mon=%d, year=%d, wday=%d\n",
177 __func__,
178 tm->tm_sec, tm->tm_min, tm->tm_hour,
179 tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday);
180
181 /* Stop the counter first */
182 txbuf[0] = PCF2123_WRITE | PCF2123_REG_CTRL1;
183 txbuf[1] = 0x20;
184 ret = spi_write(spi, txbuf, 2);
185 if (ret < 0)
186 return ret;
187 pcf2123_delay_trec();
188
189 /* Set the new time */
190 txbuf[0] = PCF2123_WRITE | PCF2123_REG_SC;
191 txbuf[1] = bin2bcd(tm->tm_sec & 0x7F);
192 txbuf[2] = bin2bcd(tm->tm_min & 0x7F);
193 txbuf[3] = bin2bcd(tm->tm_hour & 0x3F);
194 txbuf[4] = bin2bcd(tm->tm_mday & 0x3F);
195 txbuf[5] = tm->tm_wday & 0x07;
196 txbuf[6] = bin2bcd((tm->tm_mon + 1) & 0x1F); /* rtc mn 1-12 */
197 txbuf[7] = bin2bcd(tm->tm_year < 100 ? tm->tm_year : tm->tm_year - 100);
198
199 ret = spi_write(spi, txbuf, sizeof(txbuf));
200 if (ret < 0)
201 return ret;
202 pcf2123_delay_trec();
203
204 /* Start the counter */
205 txbuf[0] = PCF2123_WRITE | PCF2123_REG_CTRL1;
206 txbuf[1] = 0x00;
207 ret = spi_write(spi, txbuf, 2);
208 if (ret < 0)
209 return ret;
210 pcf2123_delay_trec();
211
212 return 0;
213}
214
215static const struct rtc_class_ops pcf2123_rtc_ops = {
216 .read_time = pcf2123_rtc_read_time,
217 .set_time = pcf2123_rtc_set_time,
218};
219
220static int __devinit pcf2123_probe(struct spi_device *spi)
221{
222 struct rtc_device *rtc;
223 struct pcf2123_plat_data *pdata;
224 u8 txbuf[2], rxbuf[2];
225 int ret, i;
226
227 pdata = kzalloc(sizeof(struct pcf2123_plat_data), GFP_KERNEL);
228 if (!pdata)
229 return -ENOMEM;
230 spi->dev.platform_data = pdata;
231
232 /* Send a software reset command */
233 txbuf[0] = PCF2123_WRITE | PCF2123_REG_CTRL1;
234 txbuf[1] = 0x58;
235 dev_dbg(&spi->dev, "resetting RTC (0x%02X 0x%02X)\n",
236 txbuf[0], txbuf[1]);
237 ret = spi_write(spi, txbuf, 2 * sizeof(u8));
238 if (ret < 0)
239 goto kfree_exit;
240 pcf2123_delay_trec();
241
242 /* Stop the counter */
243 txbuf[0] = PCF2123_WRITE | PCF2123_REG_CTRL1;
244 txbuf[1] = 0x20;
245 dev_dbg(&spi->dev, "stopping RTC (0x%02X 0x%02X)\n",
246 txbuf[0], txbuf[1]);
247 ret = spi_write(spi, txbuf, 2 * sizeof(u8));
248 if (ret < 0)
249 goto kfree_exit;
250 pcf2123_delay_trec();
251
252 /* See if the counter was actually stopped */
253 txbuf[0] = PCF2123_READ | PCF2123_REG_CTRL1;
254 dev_dbg(&spi->dev, "checking for presence of RTC (0x%02X)\n",
255 txbuf[0]);
256 ret = spi_write_then_read(spi, txbuf, 1 * sizeof(u8),
257 rxbuf, 2 * sizeof(u8));
258 dev_dbg(&spi->dev, "received data from RTC (0x%02X 0x%02X)\n",
259 rxbuf[0], rxbuf[1]);
260 if (ret < 0)
261 goto kfree_exit;
262 pcf2123_delay_trec();
263
264 if (!(rxbuf[0] & 0x20)) {
265 dev_err(&spi->dev, "chip not found\n");
266 goto kfree_exit;
267 }
268
269 dev_info(&spi->dev, "chip found, driver version " DRV_VERSION "\n");
270 dev_info(&spi->dev, "spiclk %u KHz.\n",
271 (spi->max_speed_hz + 500) / 1000);
272
273 /* Start the counter */
274 txbuf[0] = PCF2123_WRITE | PCF2123_REG_CTRL1;
275 txbuf[1] = 0x00;
276 ret = spi_write(spi, txbuf, sizeof(txbuf));
277 if (ret < 0)
278 goto kfree_exit;
279 pcf2123_delay_trec();
280
281 /* Finalize the initialization */
282 rtc = rtc_device_register(pcf2123_driver.driver.name, &spi->dev,
283 &pcf2123_rtc_ops, THIS_MODULE);
284
285 if (IS_ERR(rtc)) {
286 dev_err(&spi->dev, "failed to register.\n");
287 ret = PTR_ERR(rtc);
288 goto kfree_exit;
289 }
290
291 pdata->rtc = rtc;
292
293 for (i = 0; i < 16; i++) {
294 sprintf(pdata->regs[i].name, "%1x", i);
295 pdata->regs[i].attr.attr.mode = S_IRUGO | S_IWUSR;
296 pdata->regs[i].attr.attr.name = pdata->regs[i].name;
297 pdata->regs[i].attr.show = pcf2123_show;
298 pdata->regs[i].attr.store = pcf2123_store;
299 ret = device_create_file(&spi->dev, &pdata->regs[i].attr);
300 if (ret) {
301 dev_err(&spi->dev, "Unable to create sysfs %s\n",
302 pdata->regs[i].name);
303 goto sysfs_exit;
304 }
305 }
306
307 return 0;
308
309sysfs_exit:
310 for (i--; i >= 0; i--)
311 device_remove_file(&spi->dev, &pdata->regs[i].attr);
312
313kfree_exit:
314 kfree(pdata);
315 spi->dev.platform_data = NULL;
316 return ret;
317}
318
319static int __devexit pcf2123_remove(struct spi_device *spi)
320{
321 struct pcf2123_plat_data *pdata = spi->dev.platform_data;
322 int i;
323
324 if (pdata) {
325 struct rtc_device *rtc = pdata->rtc;
326
327 if (rtc)
328 rtc_device_unregister(rtc);
329 for (i = 0; i < 16; i++)
330 if (pdata->regs[i].name[0])
331 device_remove_file(&spi->dev,
332 &pdata->regs[i].attr);
333 kfree(pdata);
334 }
335
336 return 0;
337}
338
339static struct spi_driver pcf2123_driver = {
340 .driver = {
341 .name = "rtc-pcf2123",
342 .bus = &spi_bus_type,
343 .owner = THIS_MODULE,
344 },
345 .probe = pcf2123_probe,
346 .remove = __devexit_p(pcf2123_remove),
347};
348
349static int __init pcf2123_init(void)
350{
351 return spi_register_driver(&pcf2123_driver);
352}
353
354static void __exit pcf2123_exit(void)
355{
356 spi_unregister_driver(&pcf2123_driver);
357}
358
359MODULE_AUTHOR("Chris Verges <chrisv@cyberswitching.com>");
360MODULE_DESCRIPTION("NXP PCF2123 RTC driver");
361MODULE_LICENSE("GPL");
362MODULE_VERSION(DRV_VERSION);
363
364module_init(pcf2123_init);
365module_exit(pcf2123_exit);