Loading...
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2018 Intel Corporation */
3
4#include <linux/delay.h>
5
6#include "igc_hw.h"
7#include "igc_i225.h"
8#include "igc_mac.h"
9#include "igc_base.h"
10#include "igc.h"
11
12/**
13 * igc_reset_hw_base - Reset hardware
14 * @hw: pointer to the HW structure
15 *
16 * This resets the hardware into a known state. This is a
17 * function pointer entry point called by the api module.
18 */
19static s32 igc_reset_hw_base(struct igc_hw *hw)
20{
21 s32 ret_val;
22 u32 ctrl;
23
24 /* Prevent the PCI-E bus from sticking if there is no TLP connection
25 * on the last TLP read/write transaction when MAC is reset.
26 */
27 ret_val = igc_disable_pcie_master(hw);
28 if (ret_val)
29 hw_dbg("PCI-E Master disable polling has failed\n");
30
31 hw_dbg("Masking off all interrupts\n");
32 wr32(IGC_IMC, 0xffffffff);
33
34 wr32(IGC_RCTL, 0);
35 wr32(IGC_TCTL, IGC_TCTL_PSP);
36 wrfl();
37
38 usleep_range(10000, 20000);
39
40 ctrl = rd32(IGC_CTRL);
41
42 hw_dbg("Issuing a global reset to MAC\n");
43 wr32(IGC_CTRL, ctrl | IGC_CTRL_RST);
44
45 ret_val = igc_get_auto_rd_done(hw);
46 if (ret_val) {
47 /* When auto config read does not complete, do not
48 * return with an error. This can happen in situations
49 * where there is no eeprom and prevents getting link.
50 */
51 hw_dbg("Auto Read Done did not complete\n");
52 }
53
54 /* Clear any pending interrupt events. */
55 wr32(IGC_IMC, 0xffffffff);
56 rd32(IGC_ICR);
57
58 return ret_val;
59}
60
61/**
62 * igc_init_nvm_params_base - Init NVM func ptrs.
63 * @hw: pointer to the HW structure
64 */
65static s32 igc_init_nvm_params_base(struct igc_hw *hw)
66{
67 struct igc_nvm_info *nvm = &hw->nvm;
68 u32 eecd = rd32(IGC_EECD);
69 u16 size;
70
71 size = FIELD_GET(IGC_EECD_SIZE_EX_MASK, eecd);
72
73 /* Added to a constant, "size" becomes the left-shift value
74 * for setting word_size.
75 */
76 size += NVM_WORD_SIZE_BASE_SHIFT;
77
78 /* Just in case size is out of range, cap it to the largest
79 * EEPROM size supported
80 */
81 if (size > 15)
82 size = 15;
83
84 nvm->type = igc_nvm_eeprom_spi;
85 nvm->word_size = BIT(size);
86 nvm->opcode_bits = 8;
87 nvm->delay_usec = 1;
88
89 nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8;
90 nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ?
91 16 : 8;
92
93 if (nvm->word_size == BIT(15))
94 nvm->page_size = 128;
95
96 return 0;
97}
98
99/**
100 * igc_setup_copper_link_base - Configure copper link settings
101 * @hw: pointer to the HW structure
102 *
103 * Configures the link for auto-neg or forced speed and duplex. Then we check
104 * for link, once link is established calls to configure collision distance
105 * and flow control are called.
106 */
107static s32 igc_setup_copper_link_base(struct igc_hw *hw)
108{
109 s32 ret_val = 0;
110 u32 ctrl;
111
112 ctrl = rd32(IGC_CTRL);
113 ctrl |= IGC_CTRL_SLU;
114 ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
115 wr32(IGC_CTRL, ctrl);
116
117 ret_val = igc_setup_copper_link(hw);
118
119 return ret_val;
120}
121
122/**
123 * igc_init_mac_params_base - Init MAC func ptrs.
124 * @hw: pointer to the HW structure
125 */
126static s32 igc_init_mac_params_base(struct igc_hw *hw)
127{
128 struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base;
129 struct igc_mac_info *mac = &hw->mac;
130
131 /* Set mta register count */
132 mac->mta_reg_count = 128;
133 mac->rar_entry_count = IGC_RAR_ENTRIES;
134
135 /* reset */
136 mac->ops.reset_hw = igc_reset_hw_base;
137
138 mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225;
139 mac->ops.release_swfw_sync = igc_release_swfw_sync_i225;
140
141 /* Allow a single clear of the SW semaphore on I225 */
142 if (mac->type == igc_i225)
143 dev_spec->clear_semaphore_once = true;
144
145 /* physical interface link setup */
146 mac->ops.setup_physical_interface = igc_setup_copper_link_base;
147
148 return 0;
149}
150
151/**
152 * igc_init_phy_params_base - Init PHY func ptrs.
153 * @hw: pointer to the HW structure
154 */
155static s32 igc_init_phy_params_base(struct igc_hw *hw)
156{
157 struct igc_phy_info *phy = &hw->phy;
158 s32 ret_val = 0;
159
160 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
161 phy->reset_delay_us = 100;
162
163 /* set lan id */
164 hw->bus.func = FIELD_GET(IGC_STATUS_FUNC_MASK, rd32(IGC_STATUS));
165
166 /* Make sure the PHY is in a good state. Several people have reported
167 * firmware leaving the PHY's page select register set to something
168 * other than the default of zero, which causes the PHY ID read to
169 * access something other than the intended register.
170 */
171 ret_val = hw->phy.ops.reset(hw);
172 if (ret_val) {
173 hw_dbg("Error resetting the PHY\n");
174 goto out;
175 }
176
177 ret_val = igc_get_phy_id(hw);
178 if (ret_val)
179 return ret_val;
180
181 igc_check_for_copper_link(hw);
182
183out:
184 return ret_val;
185}
186
187static s32 igc_get_invariants_base(struct igc_hw *hw)
188{
189 struct igc_mac_info *mac = &hw->mac;
190 s32 ret_val = 0;
191
192 switch (hw->device_id) {
193 case IGC_DEV_ID_I225_LM:
194 case IGC_DEV_ID_I225_V:
195 case IGC_DEV_ID_I225_I:
196 case IGC_DEV_ID_I220_V:
197 case IGC_DEV_ID_I225_K:
198 case IGC_DEV_ID_I225_K2:
199 case IGC_DEV_ID_I226_K:
200 case IGC_DEV_ID_I225_LMVP:
201 case IGC_DEV_ID_I226_LMVP:
202 case IGC_DEV_ID_I225_IT:
203 case IGC_DEV_ID_I226_LM:
204 case IGC_DEV_ID_I226_V:
205 case IGC_DEV_ID_I226_IT:
206 case IGC_DEV_ID_I221_V:
207 case IGC_DEV_ID_I226_BLANK_NVM:
208 case IGC_DEV_ID_I225_BLANK_NVM:
209 mac->type = igc_i225;
210 break;
211 default:
212 return -IGC_ERR_MAC_INIT;
213 }
214
215 hw->phy.media_type = igc_media_type_copper;
216
217 /* mac initialization and operations */
218 ret_val = igc_init_mac_params_base(hw);
219 if (ret_val)
220 goto out;
221
222 /* NVM initialization */
223 ret_val = igc_init_nvm_params_base(hw);
224 switch (hw->mac.type) {
225 case igc_i225:
226 ret_val = igc_init_nvm_params_i225(hw);
227 break;
228 default:
229 break;
230 }
231
232 /* setup PHY parameters */
233 ret_val = igc_init_phy_params_base(hw);
234 if (ret_val)
235 goto out;
236
237out:
238 return ret_val;
239}
240
241/**
242 * igc_acquire_phy_base - Acquire rights to access PHY
243 * @hw: pointer to the HW structure
244 *
245 * Acquire access rights to the correct PHY. This is a
246 * function pointer entry point called by the api module.
247 */
248static s32 igc_acquire_phy_base(struct igc_hw *hw)
249{
250 u16 mask = IGC_SWFW_PHY0_SM;
251
252 return hw->mac.ops.acquire_swfw_sync(hw, mask);
253}
254
255/**
256 * igc_release_phy_base - Release rights to access PHY
257 * @hw: pointer to the HW structure
258 *
259 * A wrapper to release access rights to the correct PHY. This is a
260 * function pointer entry point called by the api module.
261 */
262static void igc_release_phy_base(struct igc_hw *hw)
263{
264 u16 mask = IGC_SWFW_PHY0_SM;
265
266 hw->mac.ops.release_swfw_sync(hw, mask);
267}
268
269/**
270 * igc_init_hw_base - Initialize hardware
271 * @hw: pointer to the HW structure
272 *
273 * This inits the hardware readying it for operation.
274 */
275static s32 igc_init_hw_base(struct igc_hw *hw)
276{
277 struct igc_mac_info *mac = &hw->mac;
278 u16 i, rar_count = mac->rar_entry_count;
279 s32 ret_val = 0;
280
281 /* Setup the receive address */
282 igc_init_rx_addrs(hw, rar_count);
283
284 /* Zero out the Multicast HASH table */
285 hw_dbg("Zeroing the MTA\n");
286 for (i = 0; i < mac->mta_reg_count; i++)
287 array_wr32(IGC_MTA, i, 0);
288
289 /* Zero out the Unicast HASH table */
290 hw_dbg("Zeroing the UTA\n");
291 for (i = 0; i < mac->uta_reg_count; i++)
292 array_wr32(IGC_UTA, i, 0);
293
294 /* Setup link and flow control */
295 ret_val = igc_setup_link(hw);
296
297 /* Clear all of the statistics registers (clear on read). It is
298 * important that we do this after we have tried to establish link
299 * because the symbol error count will increment wildly if there
300 * is no link.
301 */
302 igc_clear_hw_cntrs_base(hw);
303
304 return ret_val;
305}
306
307/**
308 * igc_power_down_phy_copper_base - Remove link during PHY power down
309 * @hw: pointer to the HW structure
310 *
311 * In the case of a PHY power down to save power, or to turn off link during a
312 * driver unload, or wake on lan is not enabled, remove the link.
313 */
314void igc_power_down_phy_copper_base(struct igc_hw *hw)
315{
316 /* If the management interface is not enabled, then power down */
317 if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
318 igc_power_down_phy_copper(hw);
319}
320
321/**
322 * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
323 * @hw: pointer to the HW structure
324 *
325 * After Rx enable, if manageability is enabled then there is likely some
326 * bad data at the start of the fifo and possibly in the DMA fifo. This
327 * function clears the fifos and flushes any packets that came in as rx was
328 * being enabled.
329 */
330void igc_rx_fifo_flush_base(struct igc_hw *hw)
331{
332 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
333 int i, ms_wait;
334
335 /* disable IPv6 options as per hardware errata */
336 rfctl = rd32(IGC_RFCTL);
337 rfctl |= IGC_RFCTL_IPV6_EX_DIS;
338 wr32(IGC_RFCTL, rfctl);
339
340 if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN))
341 return;
342
343 /* Disable all Rx queues */
344 for (i = 0; i < 4; i++) {
345 rxdctl[i] = rd32(IGC_RXDCTL(i));
346 wr32(IGC_RXDCTL(i),
347 rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE);
348 }
349 /* Poll all queues to verify they have shut down */
350 for (ms_wait = 0; ms_wait < 10; ms_wait++) {
351 usleep_range(1000, 2000);
352 rx_enabled = 0;
353 for (i = 0; i < 4; i++)
354 rx_enabled |= rd32(IGC_RXDCTL(i));
355 if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE))
356 break;
357 }
358
359 if (ms_wait == 10)
360 hw_dbg("Queue disable timed out after 10ms\n");
361
362 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
363 * incoming packets are rejected. Set enable and wait 2ms so that
364 * any packet that was coming in as RCTL.EN was set is flushed
365 */
366 wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF);
367
368 rlpml = rd32(IGC_RLPML);
369 wr32(IGC_RLPML, 0);
370
371 rctl = rd32(IGC_RCTL);
372 temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP);
373 temp_rctl |= IGC_RCTL_LPE;
374
375 wr32(IGC_RCTL, temp_rctl);
376 wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN);
377 wrfl();
378 usleep_range(2000, 3000);
379
380 /* Enable Rx queues that were previously enabled and restore our
381 * previous state
382 */
383 for (i = 0; i < 4; i++)
384 wr32(IGC_RXDCTL(i), rxdctl[i]);
385 wr32(IGC_RCTL, rctl);
386 wrfl();
387
388 wr32(IGC_RLPML, rlpml);
389 wr32(IGC_RFCTL, rfctl);
390
391 /* Flush receive errors generated by workaround */
392 rd32(IGC_ROC);
393 rd32(IGC_RNBC);
394 rd32(IGC_MPC);
395}
396
397bool igc_is_device_id_i225(struct igc_hw *hw)
398{
399 switch (hw->device_id) {
400 case IGC_DEV_ID_I225_LM:
401 case IGC_DEV_ID_I225_V:
402 case IGC_DEV_ID_I225_I:
403 case IGC_DEV_ID_I225_K:
404 case IGC_DEV_ID_I225_K2:
405 case IGC_DEV_ID_I225_LMVP:
406 case IGC_DEV_ID_I225_IT:
407 return true;
408 default:
409 return false;
410 }
411}
412
413bool igc_is_device_id_i226(struct igc_hw *hw)
414{
415 switch (hw->device_id) {
416 case IGC_DEV_ID_I226_LM:
417 case IGC_DEV_ID_I226_V:
418 case IGC_DEV_ID_I226_K:
419 case IGC_DEV_ID_I226_IT:
420 return true;
421 default:
422 return false;
423 }
424}
425
426static struct igc_mac_operations igc_mac_ops_base = {
427 .init_hw = igc_init_hw_base,
428 .check_for_link = igc_check_for_copper_link,
429 .rar_set = igc_rar_set,
430 .read_mac_addr = igc_read_mac_addr,
431 .get_speed_and_duplex = igc_get_speed_and_duplex_copper,
432};
433
434static const struct igc_phy_operations igc_phy_ops_base = {
435 .acquire = igc_acquire_phy_base,
436 .release = igc_release_phy_base,
437 .reset = igc_phy_hw_reset,
438 .read_reg = igc_read_phy_reg_gpy,
439 .write_reg = igc_write_phy_reg_gpy,
440};
441
442const struct igc_info igc_base_info = {
443 .get_invariants = igc_get_invariants_base,
444 .mac_ops = &igc_mac_ops_base,
445 .phy_ops = &igc_phy_ops_base,
446};
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2018 Intel Corporation */
3
4#include <linux/delay.h>
5
6#include "igc_hw.h"
7#include "igc_i225.h"
8#include "igc_mac.h"
9#include "igc_base.h"
10#include "igc.h"
11
12/**
13 * igc_reset_hw_base - Reset hardware
14 * @hw: pointer to the HW structure
15 *
16 * This resets the hardware into a known state. This is a
17 * function pointer entry point called by the api module.
18 */
19static s32 igc_reset_hw_base(struct igc_hw *hw)
20{
21 s32 ret_val;
22 u32 ctrl;
23
24 /* Prevent the PCI-E bus from sticking if there is no TLP connection
25 * on the last TLP read/write transaction when MAC is reset.
26 */
27 ret_val = igc_disable_pcie_master(hw);
28 if (ret_val)
29 hw_dbg("PCI-E Master disable polling has failed\n");
30
31 hw_dbg("Masking off all interrupts\n");
32 wr32(IGC_IMC, 0xffffffff);
33
34 wr32(IGC_RCTL, 0);
35 wr32(IGC_TCTL, IGC_TCTL_PSP);
36 wrfl();
37
38 usleep_range(10000, 20000);
39
40 ctrl = rd32(IGC_CTRL);
41
42 hw_dbg("Issuing a global reset to MAC\n");
43 wr32(IGC_CTRL, ctrl | IGC_CTRL_RST);
44
45 ret_val = igc_get_auto_rd_done(hw);
46 if (ret_val) {
47 /* When auto config read does not complete, do not
48 * return with an error. This can happen in situations
49 * where there is no eeprom and prevents getting link.
50 */
51 hw_dbg("Auto Read Done did not complete\n");
52 }
53
54 /* Clear any pending interrupt events. */
55 wr32(IGC_IMC, 0xffffffff);
56 rd32(IGC_ICR);
57
58 return ret_val;
59}
60
61/**
62 * igc_init_nvm_params_base - Init NVM func ptrs.
63 * @hw: pointer to the HW structure
64 */
65static s32 igc_init_nvm_params_base(struct igc_hw *hw)
66{
67 struct igc_nvm_info *nvm = &hw->nvm;
68 u32 eecd = rd32(IGC_EECD);
69 u16 size;
70
71 size = (u16)((eecd & IGC_EECD_SIZE_EX_MASK) >>
72 IGC_EECD_SIZE_EX_SHIFT);
73
74 /* Added to a constant, "size" becomes the left-shift value
75 * for setting word_size.
76 */
77 size += NVM_WORD_SIZE_BASE_SHIFT;
78
79 /* Just in case size is out of range, cap it to the largest
80 * EEPROM size supported
81 */
82 if (size > 15)
83 size = 15;
84
85 nvm->type = igc_nvm_eeprom_spi;
86 nvm->word_size = BIT(size);
87 nvm->opcode_bits = 8;
88 nvm->delay_usec = 1;
89
90 nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8;
91 nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ?
92 16 : 8;
93
94 if (nvm->word_size == BIT(15))
95 nvm->page_size = 128;
96
97 return 0;
98}
99
100/**
101 * igc_setup_copper_link_base - Configure copper link settings
102 * @hw: pointer to the HW structure
103 *
104 * Configures the link for auto-neg or forced speed and duplex. Then we check
105 * for link, once link is established calls to configure collision distance
106 * and flow control are called.
107 */
108static s32 igc_setup_copper_link_base(struct igc_hw *hw)
109{
110 s32 ret_val = 0;
111 u32 ctrl;
112
113 ctrl = rd32(IGC_CTRL);
114 ctrl |= IGC_CTRL_SLU;
115 ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
116 wr32(IGC_CTRL, ctrl);
117
118 ret_val = igc_setup_copper_link(hw);
119
120 return ret_val;
121}
122
123/**
124 * igc_init_mac_params_base - Init MAC func ptrs.
125 * @hw: pointer to the HW structure
126 */
127static s32 igc_init_mac_params_base(struct igc_hw *hw)
128{
129 struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base;
130 struct igc_mac_info *mac = &hw->mac;
131
132 /* Set mta register count */
133 mac->mta_reg_count = 128;
134 mac->rar_entry_count = IGC_RAR_ENTRIES;
135
136 /* reset */
137 mac->ops.reset_hw = igc_reset_hw_base;
138
139 mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225;
140 mac->ops.release_swfw_sync = igc_release_swfw_sync_i225;
141
142 /* Allow a single clear of the SW semaphore on I225 */
143 if (mac->type == igc_i225)
144 dev_spec->clear_semaphore_once = true;
145
146 /* physical interface link setup */
147 mac->ops.setup_physical_interface = igc_setup_copper_link_base;
148
149 return 0;
150}
151
152/**
153 * igc_init_phy_params_base - Init PHY func ptrs.
154 * @hw: pointer to the HW structure
155 */
156static s32 igc_init_phy_params_base(struct igc_hw *hw)
157{
158 struct igc_phy_info *phy = &hw->phy;
159 s32 ret_val = 0;
160
161 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
162 phy->reset_delay_us = 100;
163
164 /* set lan id */
165 hw->bus.func = (rd32(IGC_STATUS) & IGC_STATUS_FUNC_MASK) >>
166 IGC_STATUS_FUNC_SHIFT;
167
168 /* Make sure the PHY is in a good state. Several people have reported
169 * firmware leaving the PHY's page select register set to something
170 * other than the default of zero, which causes the PHY ID read to
171 * access something other than the intended register.
172 */
173 ret_val = hw->phy.ops.reset(hw);
174 if (ret_val) {
175 hw_dbg("Error resetting the PHY\n");
176 goto out;
177 }
178
179 ret_val = igc_get_phy_id(hw);
180 if (ret_val)
181 return ret_val;
182
183 igc_check_for_copper_link(hw);
184
185out:
186 return ret_val;
187}
188
189static s32 igc_get_invariants_base(struct igc_hw *hw)
190{
191 struct igc_mac_info *mac = &hw->mac;
192 s32 ret_val = 0;
193
194 switch (hw->device_id) {
195 case IGC_DEV_ID_I225_LM:
196 case IGC_DEV_ID_I225_V:
197 case IGC_DEV_ID_I225_I:
198 case IGC_DEV_ID_I220_V:
199 case IGC_DEV_ID_I225_K:
200 case IGC_DEV_ID_I225_K2:
201 case IGC_DEV_ID_I226_K:
202 case IGC_DEV_ID_I225_LMVP:
203 case IGC_DEV_ID_I226_LMVP:
204 case IGC_DEV_ID_I225_IT:
205 case IGC_DEV_ID_I226_LM:
206 case IGC_DEV_ID_I226_V:
207 case IGC_DEV_ID_I226_IT:
208 case IGC_DEV_ID_I221_V:
209 case IGC_DEV_ID_I226_BLANK_NVM:
210 case IGC_DEV_ID_I225_BLANK_NVM:
211 mac->type = igc_i225;
212 break;
213 default:
214 return -IGC_ERR_MAC_INIT;
215 }
216
217 hw->phy.media_type = igc_media_type_copper;
218
219 /* mac initialization and operations */
220 ret_val = igc_init_mac_params_base(hw);
221 if (ret_val)
222 goto out;
223
224 /* NVM initialization */
225 ret_val = igc_init_nvm_params_base(hw);
226 switch (hw->mac.type) {
227 case igc_i225:
228 ret_val = igc_init_nvm_params_i225(hw);
229 break;
230 default:
231 break;
232 }
233
234 /* setup PHY parameters */
235 ret_val = igc_init_phy_params_base(hw);
236 if (ret_val)
237 goto out;
238
239out:
240 return ret_val;
241}
242
243/**
244 * igc_acquire_phy_base - Acquire rights to access PHY
245 * @hw: pointer to the HW structure
246 *
247 * Acquire access rights to the correct PHY. This is a
248 * function pointer entry point called by the api module.
249 */
250static s32 igc_acquire_phy_base(struct igc_hw *hw)
251{
252 u16 mask = IGC_SWFW_PHY0_SM;
253
254 return hw->mac.ops.acquire_swfw_sync(hw, mask);
255}
256
257/**
258 * igc_release_phy_base - Release rights to access PHY
259 * @hw: pointer to the HW structure
260 *
261 * A wrapper to release access rights to the correct PHY. This is a
262 * function pointer entry point called by the api module.
263 */
264static void igc_release_phy_base(struct igc_hw *hw)
265{
266 u16 mask = IGC_SWFW_PHY0_SM;
267
268 hw->mac.ops.release_swfw_sync(hw, mask);
269}
270
271/**
272 * igc_init_hw_base - Initialize hardware
273 * @hw: pointer to the HW structure
274 *
275 * This inits the hardware readying it for operation.
276 */
277static s32 igc_init_hw_base(struct igc_hw *hw)
278{
279 struct igc_mac_info *mac = &hw->mac;
280 u16 i, rar_count = mac->rar_entry_count;
281 s32 ret_val = 0;
282
283 /* Setup the receive address */
284 igc_init_rx_addrs(hw, rar_count);
285
286 /* Zero out the Multicast HASH table */
287 hw_dbg("Zeroing the MTA\n");
288 for (i = 0; i < mac->mta_reg_count; i++)
289 array_wr32(IGC_MTA, i, 0);
290
291 /* Zero out the Unicast HASH table */
292 hw_dbg("Zeroing the UTA\n");
293 for (i = 0; i < mac->uta_reg_count; i++)
294 array_wr32(IGC_UTA, i, 0);
295
296 /* Setup link and flow control */
297 ret_val = igc_setup_link(hw);
298
299 /* Clear all of the statistics registers (clear on read). It is
300 * important that we do this after we have tried to establish link
301 * because the symbol error count will increment wildly if there
302 * is no link.
303 */
304 igc_clear_hw_cntrs_base(hw);
305
306 return ret_val;
307}
308
309/**
310 * igc_power_down_phy_copper_base - Remove link during PHY power down
311 * @hw: pointer to the HW structure
312 *
313 * In the case of a PHY power down to save power, or to turn off link during a
314 * driver unload, or wake on lan is not enabled, remove the link.
315 */
316void igc_power_down_phy_copper_base(struct igc_hw *hw)
317{
318 /* If the management interface is not enabled, then power down */
319 if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
320 igc_power_down_phy_copper(hw);
321}
322
323/**
324 * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
325 * @hw: pointer to the HW structure
326 *
327 * After Rx enable, if manageability is enabled then there is likely some
328 * bad data at the start of the fifo and possibly in the DMA fifo. This
329 * function clears the fifos and flushes any packets that came in as rx was
330 * being enabled.
331 */
332void igc_rx_fifo_flush_base(struct igc_hw *hw)
333{
334 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
335 int i, ms_wait;
336
337 /* disable IPv6 options as per hardware errata */
338 rfctl = rd32(IGC_RFCTL);
339 rfctl |= IGC_RFCTL_IPV6_EX_DIS;
340 wr32(IGC_RFCTL, rfctl);
341
342 if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN))
343 return;
344
345 /* Disable all Rx queues */
346 for (i = 0; i < 4; i++) {
347 rxdctl[i] = rd32(IGC_RXDCTL(i));
348 wr32(IGC_RXDCTL(i),
349 rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE);
350 }
351 /* Poll all queues to verify they have shut down */
352 for (ms_wait = 0; ms_wait < 10; ms_wait++) {
353 usleep_range(1000, 2000);
354 rx_enabled = 0;
355 for (i = 0; i < 4; i++)
356 rx_enabled |= rd32(IGC_RXDCTL(i));
357 if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE))
358 break;
359 }
360
361 if (ms_wait == 10)
362 hw_dbg("Queue disable timed out after 10ms\n");
363
364 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
365 * incoming packets are rejected. Set enable and wait 2ms so that
366 * any packet that was coming in as RCTL.EN was set is flushed
367 */
368 wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF);
369
370 rlpml = rd32(IGC_RLPML);
371 wr32(IGC_RLPML, 0);
372
373 rctl = rd32(IGC_RCTL);
374 temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP);
375 temp_rctl |= IGC_RCTL_LPE;
376
377 wr32(IGC_RCTL, temp_rctl);
378 wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN);
379 wrfl();
380 usleep_range(2000, 3000);
381
382 /* Enable Rx queues that were previously enabled and restore our
383 * previous state
384 */
385 for (i = 0; i < 4; i++)
386 wr32(IGC_RXDCTL(i), rxdctl[i]);
387 wr32(IGC_RCTL, rctl);
388 wrfl();
389
390 wr32(IGC_RLPML, rlpml);
391 wr32(IGC_RFCTL, rfctl);
392
393 /* Flush receive errors generated by workaround */
394 rd32(IGC_ROC);
395 rd32(IGC_RNBC);
396 rd32(IGC_MPC);
397}
398
399static struct igc_mac_operations igc_mac_ops_base = {
400 .init_hw = igc_init_hw_base,
401 .check_for_link = igc_check_for_copper_link,
402 .rar_set = igc_rar_set,
403 .read_mac_addr = igc_read_mac_addr,
404 .get_speed_and_duplex = igc_get_speed_and_duplex_copper,
405};
406
407static const struct igc_phy_operations igc_phy_ops_base = {
408 .acquire = igc_acquire_phy_base,
409 .release = igc_release_phy_base,
410 .reset = igc_phy_hw_reset,
411 .read_reg = igc_read_phy_reg_gpy,
412 .write_reg = igc_write_phy_reg_gpy,
413};
414
415const struct igc_info igc_base_info = {
416 .get_invariants = igc_get_invariants_base,
417 .mac_ops = &igc_mac_ops_base,
418 .phy_ops = &igc_phy_ops_base,
419};