Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * mxser.c -- MOXA Smartio/Industio family multiport serial driver.
4 *
5 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com).
6 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com>
7 *
8 * This code is loosely based on the 1.8 moxa driver which is based on
9 * Linux serial driver, written by Linus Torvalds, Theodore T'so and
10 * others.
11 *
12 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
13 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
14 * www.moxa.com.
15 * - Fixed x86_64 cleanness
16 */
17
18#include <linux/module.h>
19#include <linux/errno.h>
20#include <linux/signal.h>
21#include <linux/sched.h>
22#include <linux/timer.h>
23#include <linux/interrupt.h>
24#include <linux/tty.h>
25#include <linux/tty_flip.h>
26#include <linux/serial.h>
27#include <linux/serial_reg.h>
28#include <linux/major.h>
29#include <linux/string.h>
30#include <linux/fcntl.h>
31#include <linux/ptrace.h>
32#include <linux/ioport.h>
33#include <linux/mm.h>
34#include <linux/delay.h>
35#include <linux/pci.h>
36#include <linux/bitops.h>
37#include <linux/slab.h>
38#include <linux/ratelimit.h>
39
40#include <asm/io.h>
41#include <asm/irq.h>
42#include <linux/uaccess.h>
43
44/*
45 * Semi-public control interfaces
46 */
47
48/*
49 * MOXA ioctls
50 */
51
52#define MOXA 0x400
53#define MOXA_SET_OP_MODE (MOXA + 66)
54#define MOXA_GET_OP_MODE (MOXA + 67)
55
56#define RS232_MODE 0
57#define RS485_2WIRE_MODE 1
58#define RS422_MODE 2
59#define RS485_4WIRE_MODE 3
60#define OP_MODE_MASK 3
61
62/* --------------------------------------------------- */
63
64/*
65 * Follow just what Moxa Must chip defines.
66 *
67 * When LCR register (offset 0x03) is written the following value, the Must chip
68 * will enter enhanced mode. And a write to EFR (offset 0x02) bit 6,7 will
69 * change bank.
70 */
71#define MOXA_MUST_ENTER_ENHANCED 0xBF
72
73/* when enhanced mode is enabled, access to general bank register */
74#define MOXA_MUST_GDL_REGISTER 0x07
75#define MOXA_MUST_GDL_MASK 0x7F
76#define MOXA_MUST_GDL_HAS_BAD_DATA 0x80
77
78#define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */
79/* enhanced register bank select and enhanced mode setting register */
80/* This works only when LCR register equals to 0xBF */
81#define MOXA_MUST_EFR_REGISTER 0x02
82#define MOXA_MUST_EFR_EFRB_ENABLE 0x10 /* enhanced mode enable */
83/* enhanced register bank set 0, 1, 2 */
84#define MOXA_MUST_EFR_BANK0 0x00
85#define MOXA_MUST_EFR_BANK1 0x40
86#define MOXA_MUST_EFR_BANK2 0x80
87#define MOXA_MUST_EFR_BANK3 0xC0
88#define MOXA_MUST_EFR_BANK_MASK 0xC0
89
90/* set XON1 value register, when LCR=0xBF and change to bank0 */
91#define MOXA_MUST_XON1_REGISTER 0x04
92
93/* set XON2 value register, when LCR=0xBF and change to bank0 */
94#define MOXA_MUST_XON2_REGISTER 0x05
95
96/* set XOFF1 value register, when LCR=0xBF and change to bank0 */
97#define MOXA_MUST_XOFF1_REGISTER 0x06
98
99/* set XOFF2 value register, when LCR=0xBF and change to bank0 */
100#define MOXA_MUST_XOFF2_REGISTER 0x07
101
102#define MOXA_MUST_RBRTL_REGISTER 0x04
103#define MOXA_MUST_RBRTH_REGISTER 0x05
104#define MOXA_MUST_RBRTI_REGISTER 0x06
105#define MOXA_MUST_THRTL_REGISTER 0x07
106#define MOXA_MUST_ENUM_REGISTER 0x04
107#define MOXA_MUST_HWID_REGISTER 0x05
108#define MOXA_MUST_ECR_REGISTER 0x06
109#define MOXA_MUST_CSR_REGISTER 0x07
110
111#define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20 /* good data mode enable */
112#define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10 /* only good data put into RxFIFO */
113
114#define MOXA_MUST_IER_ECTSI 0x80 /* enable CTS interrupt */
115#define MOXA_MUST_IER_ERTSI 0x40 /* enable RTS interrupt */
116#define MOXA_MUST_IER_XINT 0x20 /* enable Xon/Xoff interrupt */
117#define MOXA_MUST_IER_EGDAI 0x10 /* enable GDA interrupt */
118
119#define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI)
120
121/* GDA interrupt pending */
122#define MOXA_MUST_IIR_GDA 0x1C
123#define MOXA_MUST_IIR_RDA 0x04
124#define MOXA_MUST_IIR_RTO 0x0C
125#define MOXA_MUST_IIR_LSR 0x06
126
127/* received Xon/Xoff or specical interrupt pending */
128#define MOXA_MUST_IIR_XSC 0x10
129
130/* RTS/CTS change state interrupt pending */
131#define MOXA_MUST_IIR_RTSCTS 0x20
132#define MOXA_MUST_IIR_MASK 0x3E
133
134#define MOXA_MUST_MCR_XON_FLAG 0x40
135#define MOXA_MUST_MCR_XON_ANY 0x80
136#define MOXA_MUST_MCR_TX_XON 0x08
137
138#define MOXA_MUST_EFR_SF_MASK 0x0F /* software flow control on chip mask value */
139#define MOXA_MUST_EFR_SF_TX1 0x08 /* send Xon1/Xoff1 */
140#define MOXA_MUST_EFR_SF_TX2 0x04 /* send Xon2/Xoff2 */
141#define MOXA_MUST_EFR_SF_TX12 0x0C /* send Xon1,Xon2/Xoff1,Xoff2 */
142#define MOXA_MUST_EFR_SF_TX_NO 0x00 /* don't send Xon/Xoff */
143#define MOXA_MUST_EFR_SF_TX_MASK 0x0C /* Tx software flow control mask */
144#define MOXA_MUST_EFR_SF_RX_NO 0x00 /* don't receive Xon/Xoff */
145#define MOXA_MUST_EFR_SF_RX1 0x02 /* receive Xon1/Xoff1 */
146#define MOXA_MUST_EFR_SF_RX2 0x01 /* receive Xon2/Xoff2 */
147#define MOXA_MUST_EFR_SF_RX12 0x03 /* receive Xon1,Xon2/Xoff1,Xoff2 */
148#define MOXA_MUST_EFR_SF_RX_MASK 0x03 /* Rx software flow control mask */
149
150#define MXSERMAJOR 174
151
152#define MXSER_BOARDS 4 /* Max. boards */
153#define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */
154#define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
155#define MXSER_ISR_PASS_LIMIT 100
156
157#define WAKEUP_CHARS 256
158
159#define MXSER_BAUD_BASE 921600
160#define MXSER_CUSTOM_DIVISOR (MXSER_BAUD_BASE * 16)
161
162#define PCI_DEVICE_ID_MOXA_RC7000 0x0001
163#define PCI_DEVICE_ID_MOXA_CP102 0x1020
164#define PCI_DEVICE_ID_MOXA_CP102UL 0x1021
165#define PCI_DEVICE_ID_MOXA_CP102U 0x1022
166#define PCI_DEVICE_ID_MOXA_CP102UF 0x1023
167#define PCI_DEVICE_ID_MOXA_C104 0x1040
168#define PCI_DEVICE_ID_MOXA_CP104U 0x1041
169#define PCI_DEVICE_ID_MOXA_CP104JU 0x1042
170#define PCI_DEVICE_ID_MOXA_CP104EL 0x1043
171#define PCI_DEVICE_ID_MOXA_POS104UL 0x1044
172#define PCI_DEVICE_ID_MOXA_CB108 0x1080
173#define PCI_DEVICE_ID_MOXA_CP112UL 0x1120
174#define PCI_DEVICE_ID_MOXA_CT114 0x1140
175#define PCI_DEVICE_ID_MOXA_CP114 0x1141
176#define PCI_DEVICE_ID_MOXA_CB114 0x1142
177#define PCI_DEVICE_ID_MOXA_CP114UL 0x1143
178#define PCI_DEVICE_ID_MOXA_CP118U 0x1180
179#define PCI_DEVICE_ID_MOXA_CP118EL 0x1181
180#define PCI_DEVICE_ID_MOXA_CP132 0x1320
181#define PCI_DEVICE_ID_MOXA_CP132U 0x1321
182#define PCI_DEVICE_ID_MOXA_CP134U 0x1340
183#define PCI_DEVICE_ID_MOXA_CB134I 0x1341
184#define PCI_DEVICE_ID_MOXA_CP138U 0x1380
185#define PCI_DEVICE_ID_MOXA_C168 0x1680
186#define PCI_DEVICE_ID_MOXA_CP168U 0x1681
187#define PCI_DEVICE_ID_MOXA_CP168EL 0x1682
188
189#define MXSER_NPORTS(ddata) ((ddata) & 0xffU)
190#define MXSER_HIGHBAUD 0x0100
191
192enum mxser_must_hwid {
193 MOXA_OTHER_UART = 0x00,
194 MOXA_MUST_MU150_HWID = 0x01,
195 MOXA_MUST_MU860_HWID = 0x02,
196};
197
198static const struct {
199 u8 type;
200 u8 fifo_size;
201 u8 rx_high_water;
202 u8 rx_low_water;
203 speed_t max_baud;
204} Gpci_uart_info[] = {
205 { MOXA_OTHER_UART, 16, 14, 1, 921600 },
206 { MOXA_MUST_MU150_HWID, 64, 48, 16, 230400 },
207 { MOXA_MUST_MU860_HWID, 128, 96, 32, 921600 }
208};
209#define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info)
210
211
212/* driver_data correspond to the lines in the structure above
213 see also ISA probe function before you change something */
214static const struct pci_device_id mxser_pcibrds[] = {
215 { PCI_DEVICE_DATA(MOXA, C168, 8) },
216 { PCI_DEVICE_DATA(MOXA, C104, 4) },
217 { PCI_DEVICE_DATA(MOXA, CP132, 2) },
218 { PCI_DEVICE_DATA(MOXA, CP114, 4) },
219 { PCI_DEVICE_DATA(MOXA, CT114, 4) },
220 { PCI_DEVICE_DATA(MOXA, CP102, 2 | MXSER_HIGHBAUD) },
221 { PCI_DEVICE_DATA(MOXA, CP104U, 4) },
222 { PCI_DEVICE_DATA(MOXA, CP168U, 8) },
223 { PCI_DEVICE_DATA(MOXA, CP132U, 2) },
224 { PCI_DEVICE_DATA(MOXA, CP134U, 4) },
225 { PCI_DEVICE_DATA(MOXA, CP104JU, 4) },
226 { PCI_DEVICE_DATA(MOXA, RC7000, 8) }, /* RC7000 */
227 { PCI_DEVICE_DATA(MOXA, CP118U, 8) },
228 { PCI_DEVICE_DATA(MOXA, CP102UL, 2) },
229 { PCI_DEVICE_DATA(MOXA, CP102U, 2) },
230 { PCI_DEVICE_DATA(MOXA, CP118EL, 8) },
231 { PCI_DEVICE_DATA(MOXA, CP168EL, 8) },
232 { PCI_DEVICE_DATA(MOXA, CP104EL, 4) },
233 { PCI_DEVICE_DATA(MOXA, CB108, 8) },
234 { PCI_DEVICE_DATA(MOXA, CB114, 4) },
235 { PCI_DEVICE_DATA(MOXA, CB134I, 4) },
236 { PCI_DEVICE_DATA(MOXA, CP138U, 8) },
237 { PCI_DEVICE_DATA(MOXA, POS104UL, 4) },
238 { PCI_DEVICE_DATA(MOXA, CP114UL, 4) },
239 { PCI_DEVICE_DATA(MOXA, CP102UF, 2) },
240 { PCI_DEVICE_DATA(MOXA, CP112UL, 2) },
241 { }
242};
243MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
244
245static int ttymajor = MXSERMAJOR;
246
247/* Variables for insmod */
248
249MODULE_AUTHOR("Casper Yang");
250MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
251module_param(ttymajor, int, 0);
252MODULE_LICENSE("GPL");
253
254struct mxser_board;
255
256struct mxser_port {
257 struct tty_port port;
258 struct mxser_board *board;
259
260 unsigned long ioaddr;
261 unsigned long opmode_ioaddr;
262
263 u8 rx_high_water;
264 u8 rx_low_water;
265 int type; /* UART type */
266
267 u8 x_char; /* xon/xoff character */
268 u8 IER; /* Interrupt Enable Register */
269 u8 MCR; /* Modem control register */
270 u8 FCR; /* FIFO control register */
271
272 struct async_icount icount; /* kernel counters for 4 input interrupts */
273 unsigned int timeout;
274
275 u8 read_status_mask;
276 u8 ignore_status_mask;
277 u8 xmit_fifo_size;
278
279 spinlock_t slock;
280};
281
282struct mxser_board {
283 unsigned int idx;
284 unsigned short nports;
285 int irq;
286 unsigned long vector;
287
288 enum mxser_must_hwid must_hwid;
289 speed_t max_baud;
290
291 struct mxser_port ports[] __counted_by(nports);
292};
293
294static DECLARE_BITMAP(mxser_boards, MXSER_BOARDS);
295static struct tty_driver *mxvar_sdriver;
296
297static u8 __mxser_must_set_EFR(unsigned long baseio, u8 clear, u8 set,
298 bool restore_LCR)
299{
300 u8 oldlcr, efr;
301
302 oldlcr = inb(baseio + UART_LCR);
303 outb(MOXA_MUST_ENTER_ENHANCED, baseio + UART_LCR);
304
305 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
306 efr &= ~clear;
307 efr |= set;
308
309 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
310
311 if (restore_LCR)
312 outb(oldlcr, baseio + UART_LCR);
313
314 return oldlcr;
315}
316
317static u8 mxser_must_select_bank(unsigned long baseio, u8 bank)
318{
319 return __mxser_must_set_EFR(baseio, MOXA_MUST_EFR_BANK_MASK, bank,
320 false);
321}
322
323static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
324{
325 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK0);
326 outb(value, baseio + MOXA_MUST_XON1_REGISTER);
327 outb(oldlcr, baseio + UART_LCR);
328}
329
330static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
331{
332 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK0);
333 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
334 outb(oldlcr, baseio + UART_LCR);
335}
336
337static void mxser_set_must_fifo_value(struct mxser_port *info)
338{
339 u8 oldlcr = mxser_must_select_bank(info->ioaddr, MOXA_MUST_EFR_BANK1);
340 outb(info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
341 outb(info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
342 outb(info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
343 outb(oldlcr, info->ioaddr + UART_LCR);
344}
345
346static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
347{
348 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK2);
349 outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
350 outb(oldlcr, baseio + UART_LCR);
351}
352
353static u8 mxser_get_must_hardware_id(unsigned long baseio)
354{
355 u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK2);
356 u8 id = inb(baseio + MOXA_MUST_HWID_REGISTER);
357 outb(oldlcr, baseio + UART_LCR);
358
359 return id;
360}
361
362static void mxser_must_set_EFR(unsigned long baseio, u8 clear, u8 set)
363{
364 __mxser_must_set_EFR(baseio, clear, set, true);
365}
366
367static void mxser_must_set_enhance_mode(unsigned long baseio, bool enable)
368{
369 mxser_must_set_EFR(baseio,
370 enable ? 0 : MOXA_MUST_EFR_EFRB_ENABLE,
371 enable ? MOXA_MUST_EFR_EFRB_ENABLE : 0);
372}
373
374static void mxser_must_no_sw_flow_control(unsigned long baseio)
375{
376 mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_MASK, 0);
377}
378
379static void mxser_must_set_tx_sw_flow_control(unsigned long baseio, bool enable)
380{
381 mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_TX_MASK,
382 enable ? MOXA_MUST_EFR_SF_TX1 : 0);
383}
384
385static void mxser_must_set_rx_sw_flow_control(unsigned long baseio, bool enable)
386{
387 mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_RX_MASK,
388 enable ? MOXA_MUST_EFR_SF_RX1 : 0);
389}
390
391static enum mxser_must_hwid mxser_must_get_hwid(unsigned long io)
392{
393 u8 oldmcr, hwid;
394 int i;
395
396 outb(0, io + UART_LCR);
397 mxser_must_set_enhance_mode(io, false);
398 oldmcr = inb(io + UART_MCR);
399 outb(0, io + UART_MCR);
400 mxser_set_must_xon1_value(io, 0x11);
401 if (inb(io + UART_MCR) != 0) {
402 outb(oldmcr, io + UART_MCR);
403 return MOXA_OTHER_UART;
404 }
405
406 hwid = mxser_get_must_hardware_id(io);
407 for (i = 1; i < UART_INFO_NUM; i++) /* 0 = OTHER_UART */
408 if (hwid == Gpci_uart_info[i].type)
409 return hwid;
410
411 return MOXA_OTHER_UART;
412}
413
414static bool mxser_16550A_or_MUST(struct mxser_port *info)
415{
416 return info->type == PORT_16550A || info->board->must_hwid;
417}
418
419static void mxser_process_txrx_fifo(struct mxser_port *info)
420{
421 unsigned int i;
422
423 if (info->type == PORT_16450 || info->type == PORT_8250) {
424 info->rx_high_water = 1;
425 info->rx_low_water = 1;
426 info->xmit_fifo_size = 1;
427 return;
428 }
429
430 for (i = 0; i < UART_INFO_NUM; i++)
431 if (info->board->must_hwid == Gpci_uart_info[i].type) {
432 info->rx_low_water = Gpci_uart_info[i].rx_low_water;
433 info->rx_high_water = Gpci_uart_info[i].rx_high_water;
434 info->xmit_fifo_size = Gpci_uart_info[i].fifo_size;
435 break;
436 }
437}
438
439static void __mxser_start_tx(struct mxser_port *info)
440{
441 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
442 info->IER |= UART_IER_THRI;
443 outb(info->IER, info->ioaddr + UART_IER);
444}
445
446static void mxser_start_tx(struct mxser_port *info)
447{
448 unsigned long flags;
449
450 spin_lock_irqsave(&info->slock, flags);
451 __mxser_start_tx(info);
452 spin_unlock_irqrestore(&info->slock, flags);
453}
454
455static void __mxser_stop_tx(struct mxser_port *info)
456{
457 info->IER &= ~UART_IER_THRI;
458 outb(info->IER, info->ioaddr + UART_IER);
459}
460
461static bool mxser_carrier_raised(struct tty_port *port)
462{
463 struct mxser_port *mp = container_of(port, struct mxser_port, port);
464
465 return inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD;
466}
467
468static void mxser_dtr_rts(struct tty_port *port, bool active)
469{
470 struct mxser_port *mp = container_of(port, struct mxser_port, port);
471 unsigned long flags;
472 u8 mcr;
473
474 spin_lock_irqsave(&mp->slock, flags);
475 mcr = inb(mp->ioaddr + UART_MCR);
476 if (active)
477 mcr |= UART_MCR_DTR | UART_MCR_RTS;
478 else
479 mcr &= ~(UART_MCR_DTR | UART_MCR_RTS);
480 outb(mcr, mp->ioaddr + UART_MCR);
481 spin_unlock_irqrestore(&mp->slock, flags);
482}
483
484static int mxser_set_baud(struct tty_struct *tty, speed_t newspd)
485{
486 struct mxser_port *info = tty->driver_data;
487 unsigned int quot = 0, baud;
488 unsigned char cval;
489 u64 timeout;
490
491 if (newspd > info->board->max_baud)
492 return -1;
493
494 if (newspd == 134) {
495 quot = 2 * MXSER_BAUD_BASE / 269;
496 tty_encode_baud_rate(tty, 134, 134);
497 } else if (newspd) {
498 quot = MXSER_BAUD_BASE / newspd;
499 if (quot == 0)
500 quot = 1;
501 baud = MXSER_BAUD_BASE / quot;
502 tty_encode_baud_rate(tty, baud, baud);
503 } else {
504 quot = 0;
505 }
506
507 /*
508 * worst case (128 * 1000 * 10 * 18432) needs 35 bits, so divide in the
509 * u64 domain
510 */
511 timeout = (u64)info->xmit_fifo_size * HZ * 10 * quot;
512 do_div(timeout, MXSER_BAUD_BASE);
513 info->timeout = timeout + HZ / 50; /* Add .02 seconds of slop */
514
515 if (quot) {
516 info->MCR |= UART_MCR_DTR;
517 outb(info->MCR, info->ioaddr + UART_MCR);
518 } else {
519 info->MCR &= ~UART_MCR_DTR;
520 outb(info->MCR, info->ioaddr + UART_MCR);
521 return 0;
522 }
523
524 cval = inb(info->ioaddr + UART_LCR);
525
526 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
527
528 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
529 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
530 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
531
532 if (C_BAUD(tty) == BOTHER) {
533 quot = MXSER_BAUD_BASE % newspd;
534 quot *= 8;
535 if (quot % newspd > newspd / 2) {
536 quot /= newspd;
537 quot++;
538 } else
539 quot /= newspd;
540
541 mxser_set_must_enum_value(info->ioaddr, quot);
542 } else {
543 mxser_set_must_enum_value(info->ioaddr, 0);
544 }
545
546 return 0;
547}
548
549static void mxser_handle_cts(struct tty_struct *tty, struct mxser_port *info,
550 u8 msr)
551{
552 bool cts = msr & UART_MSR_CTS;
553
554 if (tty->hw_stopped) {
555 if (cts) {
556 tty->hw_stopped = false;
557
558 if (!mxser_16550A_or_MUST(info))
559 __mxser_start_tx(info);
560 tty_wakeup(tty);
561 }
562 return;
563 } else if (cts)
564 return;
565
566 tty->hw_stopped = true;
567 if (!mxser_16550A_or_MUST(info))
568 __mxser_stop_tx(info);
569}
570
571/*
572 * This routine is called to set the UART divisor registers to match
573 * the specified baud rate for a serial port.
574 */
575static void mxser_change_speed(struct tty_struct *tty,
576 const struct ktermios *old_termios)
577{
578 struct mxser_port *info = tty->driver_data;
579 unsigned cflag, cval;
580
581 cflag = tty->termios.c_cflag;
582
583 if (mxser_set_baud(tty, tty_get_baud_rate(tty))) {
584 /* Use previous rate on a failure */
585 if (old_termios) {
586 speed_t baud = tty_termios_baud_rate(old_termios);
587 tty_encode_baud_rate(tty, baud, baud);
588 }
589 }
590
591 /* byte size and parity */
592 cval = UART_LCR_WLEN(tty_get_char_size(tty->termios.c_cflag));
593
594 if (cflag & CSTOPB)
595 cval |= UART_LCR_STOP;
596 if (cflag & PARENB)
597 cval |= UART_LCR_PARITY;
598 if (!(cflag & PARODD))
599 cval |= UART_LCR_EPAR;
600 if (cflag & CMSPAR)
601 cval |= UART_LCR_SPAR;
602
603 info->FCR = 0;
604 if (info->board->must_hwid) {
605 info->FCR |= UART_FCR_ENABLE_FIFO |
606 MOXA_MUST_FCR_GDA_MODE_ENABLE;
607 mxser_set_must_fifo_value(info);
608 } else if (info->type != PORT_8250 && info->type != PORT_16450) {
609 info->FCR |= UART_FCR_ENABLE_FIFO;
610 switch (info->rx_high_water) {
611 case 1:
612 info->FCR |= UART_FCR_TRIGGER_1;
613 break;
614 case 4:
615 info->FCR |= UART_FCR_TRIGGER_4;
616 break;
617 case 8:
618 info->FCR |= UART_FCR_TRIGGER_8;
619 break;
620 default:
621 info->FCR |= UART_FCR_TRIGGER_14;
622 break;
623 }
624 }
625
626 /* CTS flow control flag and modem status interrupts */
627 info->IER &= ~UART_IER_MSI;
628 info->MCR &= ~UART_MCR_AFE;
629 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
630 if (cflag & CRTSCTS) {
631 info->IER |= UART_IER_MSI;
632 if (mxser_16550A_or_MUST(info)) {
633 info->MCR |= UART_MCR_AFE;
634 } else {
635 mxser_handle_cts(tty, info,
636 inb(info->ioaddr + UART_MSR));
637 }
638 }
639 outb(info->MCR, info->ioaddr + UART_MCR);
640 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
641 if (~cflag & CLOCAL)
642 info->IER |= UART_IER_MSI;
643 outb(info->IER, info->ioaddr + UART_IER);
644
645 /*
646 * Set up parity check flag
647 */
648 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
649 if (I_INPCK(tty))
650 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
651 if (I_BRKINT(tty) || I_PARMRK(tty))
652 info->read_status_mask |= UART_LSR_BI;
653
654 info->ignore_status_mask = 0;
655
656 if (I_IGNBRK(tty)) {
657 info->ignore_status_mask |= UART_LSR_BI;
658 info->read_status_mask |= UART_LSR_BI;
659 /*
660 * If we're ignore parity and break indicators, ignore
661 * overruns too. (For real raw support).
662 */
663 if (I_IGNPAR(tty)) {
664 info->ignore_status_mask |=
665 UART_LSR_OE |
666 UART_LSR_PE |
667 UART_LSR_FE;
668 info->read_status_mask |=
669 UART_LSR_OE |
670 UART_LSR_PE |
671 UART_LSR_FE;
672 }
673 }
674 if (info->board->must_hwid) {
675 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
676 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
677 mxser_must_set_rx_sw_flow_control(info->ioaddr, I_IXON(tty));
678 mxser_must_set_tx_sw_flow_control(info->ioaddr, I_IXOFF(tty));
679 }
680
681
682 outb(info->FCR, info->ioaddr + UART_FCR);
683 outb(cval, info->ioaddr + UART_LCR);
684}
685
686static u8 mxser_check_modem_status(struct tty_struct *tty,
687 struct mxser_port *port)
688{
689 u8 msr = inb(port->ioaddr + UART_MSR);
690
691 if (!(msr & UART_MSR_ANY_DELTA))
692 return msr;
693
694 /* update input line counters */
695 if (msr & UART_MSR_TERI)
696 port->icount.rng++;
697 if (msr & UART_MSR_DDSR)
698 port->icount.dsr++;
699 if (msr & UART_MSR_DDCD)
700 port->icount.dcd++;
701 if (msr & UART_MSR_DCTS)
702 port->icount.cts++;
703 wake_up_interruptible(&port->port.delta_msr_wait);
704
705 if (tty_port_check_carrier(&port->port) && (msr & UART_MSR_DDCD)) {
706 if (msr & UART_MSR_DCD)
707 wake_up_interruptible(&port->port.open_wait);
708 }
709
710 if (tty_port_cts_enabled(&port->port))
711 mxser_handle_cts(tty, port, msr);
712
713 return msr;
714}
715
716static void mxser_disable_and_clear_FIFO(struct mxser_port *info)
717{
718 u8 fcr = UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT;
719
720 if (info->board->must_hwid)
721 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
722
723 outb(fcr, info->ioaddr + UART_FCR);
724}
725
726static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
727{
728 struct mxser_port *info = container_of(port, struct mxser_port, port);
729 unsigned long flags;
730 int ret;
731
732 ret = tty_port_alloc_xmit_buf(port);
733 if (ret < 0)
734 return ret;
735
736 spin_lock_irqsave(&info->slock, flags);
737
738 if (!info->type) {
739 set_bit(TTY_IO_ERROR, &tty->flags);
740 spin_unlock_irqrestore(&info->slock, flags);
741 ret = 0;
742 goto err_free_xmit;
743 }
744
745 /*
746 * Clear the FIFO buffers and disable them
747 * (they will be reenabled in mxser_change_speed())
748 */
749 mxser_disable_and_clear_FIFO(info);
750
751 /*
752 * At this point there's no way the LSR could still be 0xFF;
753 * if it is, then bail out, because there's likely no UART
754 * here.
755 */
756 if (inb(info->ioaddr + UART_LSR) == 0xff) {
757 spin_unlock_irqrestore(&info->slock, flags);
758 if (capable(CAP_SYS_ADMIN)) {
759 set_bit(TTY_IO_ERROR, &tty->flags);
760 return 0;
761 }
762
763 ret = -ENODEV;
764 goto err_free_xmit;
765 }
766
767 /*
768 * Clear the interrupt registers.
769 */
770 (void) inb(info->ioaddr + UART_LSR);
771 (void) inb(info->ioaddr + UART_RX);
772 (void) inb(info->ioaddr + UART_IIR);
773 (void) inb(info->ioaddr + UART_MSR);
774
775 /*
776 * Now, initialize the UART
777 */
778 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
779 info->MCR = UART_MCR_DTR | UART_MCR_RTS;
780 outb(info->MCR, info->ioaddr + UART_MCR);
781
782 /*
783 * Finally, enable interrupts
784 */
785 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
786
787 if (info->board->must_hwid)
788 info->IER |= MOXA_MUST_IER_EGDAI;
789 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */
790
791 /*
792 * And clear the interrupt registers again for luck.
793 */
794 (void) inb(info->ioaddr + UART_LSR);
795 (void) inb(info->ioaddr + UART_RX);
796 (void) inb(info->ioaddr + UART_IIR);
797 (void) inb(info->ioaddr + UART_MSR);
798
799 clear_bit(TTY_IO_ERROR, &tty->flags);
800 kfifo_reset(&port->xmit_fifo);
801
802 /*
803 * and set the speed of the serial port
804 */
805 mxser_change_speed(tty, NULL);
806 spin_unlock_irqrestore(&info->slock, flags);
807
808 return 0;
809err_free_xmit:
810 tty_port_free_xmit_buf(port);
811 return ret;
812}
813
814/*
815 * To stop accepting input, we disable the receive line status interrupts, and
816 * tell the interrupt driver to stop checking the data ready bit in the line
817 * status register.
818 */
819static void mxser_stop_rx(struct mxser_port *info)
820{
821 info->IER &= ~UART_IER_RLSI;
822 if (info->board->must_hwid)
823 info->IER &= ~MOXA_MUST_RECV_ISR;
824
825 outb(info->IER, info->ioaddr + UART_IER);
826}
827
828/*
829 * This routine will shutdown a serial port
830 */
831static void mxser_shutdown_port(struct tty_port *port)
832{
833 struct mxser_port *info = container_of(port, struct mxser_port, port);
834 unsigned long flags;
835
836 spin_lock_irqsave(&info->slock, flags);
837
838 mxser_stop_rx(info);
839
840 /*
841 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
842 * here so the queue might never be waken up
843 */
844 wake_up_interruptible(&info->port.delta_msr_wait);
845
846 info->IER = 0;
847 outb(0x00, info->ioaddr + UART_IER);
848
849 /* clear Rx/Tx FIFO's */
850 mxser_disable_and_clear_FIFO(info);
851
852 /* read data port to reset things */
853 (void) inb(info->ioaddr + UART_RX);
854
855
856 if (info->board->must_hwid)
857 mxser_must_no_sw_flow_control(info->ioaddr);
858
859 spin_unlock_irqrestore(&info->slock, flags);
860
861 /* make sure ISR is not running while we free the buffer */
862 synchronize_irq(info->board->irq);
863
864 tty_port_free_xmit_buf(port);
865}
866
867/*
868 * This routine is called whenever a serial port is opened. It
869 * enables interrupts for a serial port, linking in its async structure into
870 * the IRQ chain. It also performs the serial-specific
871 * initialization for the tty structure.
872 */
873static int mxser_open(struct tty_struct *tty, struct file *filp)
874{
875 struct tty_port *tport = tty->port;
876 struct mxser_port *port = container_of(tport, struct mxser_port, port);
877
878 tty->driver_data = port;
879
880 return tty_port_open(tport, tty, filp);
881}
882
883static void mxser_flush_buffer(struct tty_struct *tty)
884{
885 struct mxser_port *info = tty->driver_data;
886 unsigned long flags;
887
888 spin_lock_irqsave(&info->slock, flags);
889 kfifo_reset(&info->port.xmit_fifo);
890
891 outb(info->FCR | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
892 info->ioaddr + UART_FCR);
893
894 spin_unlock_irqrestore(&info->slock, flags);
895
896 tty_wakeup(tty);
897}
898
899static void mxser_close(struct tty_struct *tty, struct file *filp)
900{
901 tty_port_close(tty->port, tty, filp);
902}
903
904static ssize_t mxser_write(struct tty_struct *tty, const u8 *buf, size_t count)
905{
906 struct mxser_port *info = tty->driver_data;
907 unsigned long flags;
908 size_t written;
909 bool is_empty;
910
911 spin_lock_irqsave(&info->slock, flags);
912 written = kfifo_in(&info->port.xmit_fifo, buf, count);
913 is_empty = kfifo_is_empty(&info->port.xmit_fifo);
914 spin_unlock_irqrestore(&info->slock, flags);
915
916 if (!is_empty && !tty->flow.stopped)
917 if (!tty->hw_stopped || mxser_16550A_or_MUST(info))
918 mxser_start_tx(info);
919
920 return written;
921}
922
923static int mxser_put_char(struct tty_struct *tty, u8 ch)
924{
925 struct mxser_port *info = tty->driver_data;
926 unsigned long flags;
927 int ret;
928
929 spin_lock_irqsave(&info->slock, flags);
930 ret = kfifo_put(&info->port.xmit_fifo, ch);
931 spin_unlock_irqrestore(&info->slock, flags);
932
933 return ret;
934}
935
936
937static void mxser_flush_chars(struct tty_struct *tty)
938{
939 struct mxser_port *info = tty->driver_data;
940
941 if (kfifo_is_empty(&info->port.xmit_fifo) || tty->flow.stopped ||
942 (tty->hw_stopped && !mxser_16550A_or_MUST(info)))
943 return;
944
945 mxser_start_tx(info);
946}
947
948static unsigned int mxser_write_room(struct tty_struct *tty)
949{
950 struct mxser_port *info = tty->driver_data;
951
952 return kfifo_avail(&info->port.xmit_fifo);
953}
954
955static unsigned int mxser_chars_in_buffer(struct tty_struct *tty)
956{
957 struct mxser_port *info = tty->driver_data;
958
959 return kfifo_len(&info->port.xmit_fifo);
960}
961
962/*
963 * ------------------------------------------------------------
964 * friends of mxser_ioctl()
965 * ------------------------------------------------------------
966 */
967static int mxser_get_serial_info(struct tty_struct *tty,
968 struct serial_struct *ss)
969{
970 struct mxser_port *info = tty->driver_data;
971 struct tty_port *port = &info->port;
972 unsigned int closing_wait, close_delay;
973
974 mutex_lock(&port->mutex);
975
976 close_delay = jiffies_to_msecs(info->port.close_delay) / 10;
977 closing_wait = info->port.closing_wait;
978 if (closing_wait != ASYNC_CLOSING_WAIT_NONE)
979 closing_wait = jiffies_to_msecs(closing_wait) / 10;
980
981 ss->type = info->type;
982 ss->line = tty->index;
983 ss->port = info->ioaddr;
984 ss->irq = info->board->irq;
985 ss->flags = info->port.flags;
986 ss->baud_base = MXSER_BAUD_BASE;
987 ss->close_delay = close_delay;
988 ss->closing_wait = closing_wait;
989 ss->custom_divisor = MXSER_CUSTOM_DIVISOR,
990 mutex_unlock(&port->mutex);
991 return 0;
992}
993
994static int mxser_set_serial_info(struct tty_struct *tty,
995 struct serial_struct *ss)
996{
997 struct mxser_port *info = tty->driver_data;
998 struct tty_port *port = &info->port;
999 speed_t baud;
1000 unsigned long sl_flags;
1001 unsigned int old_speed, close_delay, closing_wait;
1002 int retval = 0;
1003
1004 if (tty_io_error(tty))
1005 return -EIO;
1006
1007 mutex_lock(&port->mutex);
1008
1009 if (ss->irq != info->board->irq ||
1010 ss->port != info->ioaddr) {
1011 mutex_unlock(&port->mutex);
1012 return -EINVAL;
1013 }
1014
1015 old_speed = port->flags & ASYNC_SPD_MASK;
1016
1017 close_delay = msecs_to_jiffies(ss->close_delay * 10);
1018 closing_wait = ss->closing_wait;
1019 if (closing_wait != ASYNC_CLOSING_WAIT_NONE)
1020 closing_wait = msecs_to_jiffies(closing_wait * 10);
1021
1022 if (!capable(CAP_SYS_ADMIN)) {
1023 if ((ss->baud_base != MXSER_BAUD_BASE) ||
1024 (close_delay != port->close_delay) ||
1025 (closing_wait != port->closing_wait) ||
1026 ((ss->flags & ~ASYNC_USR_MASK) != (port->flags & ~ASYNC_USR_MASK))) {
1027 mutex_unlock(&port->mutex);
1028 return -EPERM;
1029 }
1030 port->flags = (port->flags & ~ASYNC_USR_MASK) |
1031 (ss->flags & ASYNC_USR_MASK);
1032 } else {
1033 /*
1034 * OK, past this point, all the error checking has been done.
1035 * At this point, we start making changes.....
1036 */
1037 port->flags = ((port->flags & ~ASYNC_FLAGS) |
1038 (ss->flags & ASYNC_FLAGS));
1039 port->close_delay = close_delay;
1040 port->closing_wait = closing_wait;
1041 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
1042 (ss->baud_base != MXSER_BAUD_BASE ||
1043 ss->custom_divisor !=
1044 MXSER_CUSTOM_DIVISOR)) {
1045 if (ss->custom_divisor == 0) {
1046 mutex_unlock(&port->mutex);
1047 return -EINVAL;
1048 }
1049 baud = ss->baud_base / ss->custom_divisor;
1050 tty_encode_baud_rate(tty, baud, baud);
1051 }
1052
1053 info->type = ss->type;
1054
1055 mxser_process_txrx_fifo(info);
1056 }
1057
1058 if (tty_port_initialized(port)) {
1059 if (old_speed != (port->flags & ASYNC_SPD_MASK)) {
1060 spin_lock_irqsave(&info->slock, sl_flags);
1061 mxser_change_speed(tty, NULL);
1062 spin_unlock_irqrestore(&info->slock, sl_flags);
1063 }
1064 } else {
1065 retval = mxser_activate(port, tty);
1066 if (retval == 0)
1067 tty_port_set_initialized(port, true);
1068 }
1069 mutex_unlock(&port->mutex);
1070 return retval;
1071}
1072
1073/*
1074 * mxser_get_lsr_info - get line status register info
1075 *
1076 * Purpose: Let user call ioctl() to get info when the UART physically
1077 * is emptied. On bus types like RS485, the transmitter must
1078 * release the bus after transmitting. This must be done when
1079 * the transmit shift register is empty, not be done when the
1080 * transmit holding register is empty. This functionality
1081 * allows an RS485 driver to be written in user space.
1082 */
1083static int mxser_get_lsr_info(struct mxser_port *info,
1084 unsigned int __user *value)
1085{
1086 unsigned char status;
1087 unsigned int result;
1088 unsigned long flags;
1089
1090 spin_lock_irqsave(&info->slock, flags);
1091 status = inb(info->ioaddr + UART_LSR);
1092 spin_unlock_irqrestore(&info->slock, flags);
1093 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1094 return put_user(result, value);
1095}
1096
1097static int mxser_tiocmget(struct tty_struct *tty)
1098{
1099 struct mxser_port *info = tty->driver_data;
1100 unsigned char control;
1101 unsigned long flags;
1102 u8 msr;
1103
1104 if (tty_io_error(tty))
1105 return -EIO;
1106
1107 spin_lock_irqsave(&info->slock, flags);
1108 control = info->MCR;
1109 msr = mxser_check_modem_status(tty, info);
1110 spin_unlock_irqrestore(&info->slock, flags);
1111
1112 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
1113 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
1114 ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) |
1115 ((msr & UART_MSR_RI) ? TIOCM_RNG : 0) |
1116 ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0) |
1117 ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0);
1118}
1119
1120static int mxser_tiocmset(struct tty_struct *tty,
1121 unsigned int set, unsigned int clear)
1122{
1123 struct mxser_port *info = tty->driver_data;
1124 unsigned long flags;
1125
1126 if (tty_io_error(tty))
1127 return -EIO;
1128
1129 spin_lock_irqsave(&info->slock, flags);
1130
1131 if (set & TIOCM_RTS)
1132 info->MCR |= UART_MCR_RTS;
1133 if (set & TIOCM_DTR)
1134 info->MCR |= UART_MCR_DTR;
1135
1136 if (clear & TIOCM_RTS)
1137 info->MCR &= ~UART_MCR_RTS;
1138 if (clear & TIOCM_DTR)
1139 info->MCR &= ~UART_MCR_DTR;
1140
1141 outb(info->MCR, info->ioaddr + UART_MCR);
1142 spin_unlock_irqrestore(&info->slock, flags);
1143 return 0;
1144}
1145
1146static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
1147 struct async_icount *cprev)
1148{
1149 struct async_icount cnow;
1150 unsigned long flags;
1151 int ret;
1152
1153 spin_lock_irqsave(&info->slock, flags);
1154 cnow = info->icount; /* atomic copy */
1155 spin_unlock_irqrestore(&info->slock, flags);
1156
1157 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
1158 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
1159 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
1160 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
1161
1162 *cprev = cnow;
1163
1164 return ret;
1165}
1166
1167/* We should likely switch to TIOCGRS485/TIOCSRS485. */
1168static int mxser_ioctl_op_mode(struct mxser_port *port, int index, bool set,
1169 int __user *u_opmode)
1170{
1171 int opmode, p = index % 4;
1172 int shiftbit = p * 2;
1173 u8 val;
1174
1175 if (port->board->must_hwid != MOXA_MUST_MU860_HWID)
1176 return -EFAULT;
1177
1178 if (set) {
1179 if (get_user(opmode, u_opmode))
1180 return -EFAULT;
1181
1182 if (opmode & ~OP_MODE_MASK)
1183 return -EINVAL;
1184
1185 spin_lock_irq(&port->slock);
1186 val = inb(port->opmode_ioaddr);
1187 val &= ~(OP_MODE_MASK << shiftbit);
1188 val |= (opmode << shiftbit);
1189 outb(val, port->opmode_ioaddr);
1190 spin_unlock_irq(&port->slock);
1191
1192 return 0;
1193 }
1194
1195 spin_lock_irq(&port->slock);
1196 opmode = inb(port->opmode_ioaddr) >> shiftbit;
1197 spin_unlock_irq(&port->slock);
1198
1199 return put_user(opmode & OP_MODE_MASK, u_opmode);
1200}
1201
1202static int mxser_ioctl(struct tty_struct *tty,
1203 unsigned int cmd, unsigned long arg)
1204{
1205 struct mxser_port *info = tty->driver_data;
1206 struct async_icount cnow;
1207 unsigned long flags;
1208 void __user *argp = (void __user *)arg;
1209
1210 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE)
1211 return mxser_ioctl_op_mode(info, tty->index,
1212 cmd == MOXA_SET_OP_MODE, argp);
1213
1214 if (cmd != TIOCMIWAIT && tty_io_error(tty))
1215 return -EIO;
1216
1217 switch (cmd) {
1218 case TIOCSERGETLSR: /* Get line status register */
1219 return mxser_get_lsr_info(info, argp);
1220 /*
1221 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1222 * - mask passed in arg for lines of interest
1223 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1224 * Caller should use TIOCGICOUNT to see which one it was
1225 */
1226 case TIOCMIWAIT:
1227 spin_lock_irqsave(&info->slock, flags);
1228 cnow = info->icount; /* note the counters on entry */
1229 spin_unlock_irqrestore(&info->slock, flags);
1230
1231 return wait_event_interruptible(info->port.delta_msr_wait,
1232 mxser_cflags_changed(info, arg, &cnow));
1233 default:
1234 return -ENOIOCTLCMD;
1235 }
1236 return 0;
1237}
1238
1239 /*
1240 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1241 * Return: write counters to the user passed counter struct
1242 * NB: both 1->0 and 0->1 transitions are counted except for
1243 * RI where only 0->1 is counted.
1244 */
1245
1246static int mxser_get_icount(struct tty_struct *tty,
1247 struct serial_icounter_struct *icount)
1248
1249{
1250 struct mxser_port *info = tty->driver_data;
1251 struct async_icount cnow;
1252 unsigned long flags;
1253
1254 spin_lock_irqsave(&info->slock, flags);
1255 cnow = info->icount;
1256 spin_unlock_irqrestore(&info->slock, flags);
1257
1258 icount->frame = cnow.frame;
1259 icount->brk = cnow.brk;
1260 icount->overrun = cnow.overrun;
1261 icount->buf_overrun = cnow.buf_overrun;
1262 icount->parity = cnow.parity;
1263 icount->rx = cnow.rx;
1264 icount->tx = cnow.tx;
1265 icount->cts = cnow.cts;
1266 icount->dsr = cnow.dsr;
1267 icount->rng = cnow.rng;
1268 icount->dcd = cnow.dcd;
1269 return 0;
1270}
1271
1272/*
1273 * This routine is called by the upper-layer tty layer to signal that
1274 * incoming characters should be throttled.
1275 */
1276static void mxser_throttle(struct tty_struct *tty)
1277{
1278 struct mxser_port *info = tty->driver_data;
1279
1280 if (I_IXOFF(tty)) {
1281 if (info->board->must_hwid) {
1282 info->IER &= ~MOXA_MUST_RECV_ISR;
1283 outb(info->IER, info->ioaddr + UART_IER);
1284 } else {
1285 info->x_char = STOP_CHAR(tty);
1286 outb(0, info->ioaddr + UART_IER);
1287 info->IER |= UART_IER_THRI;
1288 outb(info->IER, info->ioaddr + UART_IER);
1289 }
1290 }
1291
1292 if (C_CRTSCTS(tty)) {
1293 info->MCR &= ~UART_MCR_RTS;
1294 outb(info->MCR, info->ioaddr + UART_MCR);
1295 }
1296}
1297
1298static void mxser_unthrottle(struct tty_struct *tty)
1299{
1300 struct mxser_port *info = tty->driver_data;
1301
1302 /* startrx */
1303 if (I_IXOFF(tty)) {
1304 if (info->x_char)
1305 info->x_char = 0;
1306 else {
1307 if (info->board->must_hwid) {
1308 info->IER |= MOXA_MUST_RECV_ISR;
1309 outb(info->IER, info->ioaddr + UART_IER);
1310 } else {
1311 info->x_char = START_CHAR(tty);
1312 outb(0, info->ioaddr + UART_IER);
1313 info->IER |= UART_IER_THRI;
1314 outb(info->IER, info->ioaddr + UART_IER);
1315 }
1316 }
1317 }
1318
1319 if (C_CRTSCTS(tty)) {
1320 info->MCR |= UART_MCR_RTS;
1321 outb(info->MCR, info->ioaddr + UART_MCR);
1322 }
1323}
1324
1325/*
1326 * mxser_stop() and mxser_start()
1327 *
1328 * This routines are called before setting or resetting tty->flow.stopped.
1329 * They enable or disable transmitter interrupts, as necessary.
1330 */
1331static void mxser_stop(struct tty_struct *tty)
1332{
1333 struct mxser_port *info = tty->driver_data;
1334 unsigned long flags;
1335
1336 spin_lock_irqsave(&info->slock, flags);
1337 if (info->IER & UART_IER_THRI)
1338 __mxser_stop_tx(info);
1339 spin_unlock_irqrestore(&info->slock, flags);
1340}
1341
1342static void mxser_start(struct tty_struct *tty)
1343{
1344 struct mxser_port *info = tty->driver_data;
1345 unsigned long flags;
1346
1347 spin_lock_irqsave(&info->slock, flags);
1348 if (!kfifo_is_empty(&info->port.xmit_fifo))
1349 __mxser_start_tx(info);
1350 spin_unlock_irqrestore(&info->slock, flags);
1351}
1352
1353static void mxser_set_termios(struct tty_struct *tty,
1354 const struct ktermios *old_termios)
1355{
1356 struct mxser_port *info = tty->driver_data;
1357 unsigned long flags;
1358
1359 spin_lock_irqsave(&info->slock, flags);
1360 mxser_change_speed(tty, old_termios);
1361 spin_unlock_irqrestore(&info->slock, flags);
1362
1363 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
1364 tty->hw_stopped = false;
1365 mxser_start(tty);
1366 }
1367
1368 /* Handle sw stopped */
1369 if ((old_termios->c_iflag & IXON) && !I_IXON(tty)) {
1370 tty->flow.stopped = 0;
1371
1372 if (info->board->must_hwid) {
1373 spin_lock_irqsave(&info->slock, flags);
1374 mxser_must_set_rx_sw_flow_control(info->ioaddr, false);
1375 spin_unlock_irqrestore(&info->slock, flags);
1376 }
1377
1378 mxser_start(tty);
1379 }
1380}
1381
1382static bool mxser_tx_empty(struct mxser_port *info)
1383{
1384 unsigned long flags;
1385 u8 lsr;
1386
1387 spin_lock_irqsave(&info->slock, flags);
1388 lsr = inb(info->ioaddr + UART_LSR);
1389 spin_unlock_irqrestore(&info->slock, flags);
1390
1391 return !(lsr & UART_LSR_TEMT);
1392}
1393
1394/*
1395 * mxser_wait_until_sent() --- wait until the transmitter is empty
1396 */
1397static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
1398{
1399 struct mxser_port *info = tty->driver_data;
1400 unsigned long expire, char_time;
1401
1402 if (info->type == PORT_UNKNOWN)
1403 return;
1404
1405 if (info->xmit_fifo_size == 0)
1406 return; /* Just in case.... */
1407
1408 /*
1409 * Set the check interval to be 1/5 of the estimated time to
1410 * send a single character, and make it at least 1. The check
1411 * interval should also be less than the timeout.
1412 *
1413 * Note: we have to use pretty tight timings here to satisfy
1414 * the NIST-PCTS.
1415 */
1416 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
1417 char_time = char_time / 5;
1418 if (char_time == 0)
1419 char_time = 1;
1420 if (timeout && timeout < char_time)
1421 char_time = timeout;
1422
1423 char_time = jiffies_to_msecs(char_time);
1424
1425 /*
1426 * If the transmitter hasn't cleared in twice the approximate
1427 * amount of time to send the entire FIFO, it probably won't
1428 * ever clear. This assumes the UART isn't doing flow
1429 * control, which is currently the case. Hence, if it ever
1430 * takes longer than info->timeout, this is probably due to a
1431 * UART bug of some kind. So, we clamp the timeout parameter at
1432 * 2*info->timeout.
1433 */
1434 if (!timeout || timeout > 2 * info->timeout)
1435 timeout = 2 * info->timeout;
1436
1437 expire = jiffies + timeout;
1438
1439 while (mxser_tx_empty(info)) {
1440 msleep_interruptible(char_time);
1441 if (signal_pending(current))
1442 break;
1443 if (time_after(jiffies, expire))
1444 break;
1445 }
1446}
1447
1448/*
1449 * This routine is called by tty_hangup() when a hangup is signaled.
1450 */
1451static void mxser_hangup(struct tty_struct *tty)
1452{
1453 struct mxser_port *info = tty->driver_data;
1454
1455 mxser_flush_buffer(tty);
1456 tty_port_hangup(&info->port);
1457}
1458
1459/*
1460 * mxser_rs_break() --- routine which turns the break handling on or off
1461 */
1462static int mxser_rs_break(struct tty_struct *tty, int break_state)
1463{
1464 struct mxser_port *info = tty->driver_data;
1465 unsigned long flags;
1466 u8 lcr;
1467
1468 spin_lock_irqsave(&info->slock, flags);
1469 lcr = inb(info->ioaddr + UART_LCR);
1470 if (break_state == -1)
1471 lcr |= UART_LCR_SBC;
1472 else
1473 lcr &= ~UART_LCR_SBC;
1474 outb(lcr, info->ioaddr + UART_LCR);
1475 spin_unlock_irqrestore(&info->slock, flags);
1476
1477 return 0;
1478}
1479
1480static bool mxser_receive_chars_new(struct mxser_port *port, u8 status)
1481{
1482 enum mxser_must_hwid hwid = port->board->must_hwid;
1483 u8 gdl;
1484
1485 if (hwid == MOXA_OTHER_UART)
1486 return false;
1487 if (status & (UART_LSR_BRK_ERROR_BITS | MOXA_MUST_LSR_RERR))
1488 return false;
1489
1490 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
1491 if (hwid == MOXA_MUST_MU150_HWID)
1492 gdl &= MOXA_MUST_GDL_MASK;
1493
1494 while (gdl--) {
1495 u8 ch = inb(port->ioaddr + UART_RX);
1496 if (!tty_insert_flip_char(&port->port, ch, 0))
1497 port->icount.buf_overrun++;
1498 }
1499
1500 return true;
1501}
1502
1503static u8 mxser_receive_chars_old(struct tty_struct *tty,
1504 struct mxser_port *port, u8 status)
1505{
1506 enum mxser_must_hwid hwid = port->board->must_hwid;
1507 int ignored = 0;
1508 int max = 256;
1509 u8 ch;
1510
1511 do {
1512 if (max-- < 0)
1513 break;
1514
1515 ch = inb(port->ioaddr + UART_RX);
1516 if (hwid && (status & UART_LSR_OE))
1517 outb(port->FCR | UART_FCR_CLEAR_RCVR,
1518 port->ioaddr + UART_FCR);
1519 status &= port->read_status_mask;
1520 if (status & port->ignore_status_mask) {
1521 if (++ignored > 100)
1522 break;
1523 } else {
1524 u8 flag = 0;
1525 if (status & UART_LSR_BRK_ERROR_BITS) {
1526 if (status & UART_LSR_BI) {
1527 flag = TTY_BREAK;
1528 port->icount.brk++;
1529
1530 if (port->port.flags & ASYNC_SAK)
1531 do_SAK(tty);
1532 } else if (status & UART_LSR_PE) {
1533 flag = TTY_PARITY;
1534 port->icount.parity++;
1535 } else if (status & UART_LSR_FE) {
1536 flag = TTY_FRAME;
1537 port->icount.frame++;
1538 } else if (status & UART_LSR_OE) {
1539 flag = TTY_OVERRUN;
1540 port->icount.overrun++;
1541 }
1542 }
1543 if (!tty_insert_flip_char(&port->port, ch, flag)) {
1544 port->icount.buf_overrun++;
1545 break;
1546 }
1547 }
1548
1549 if (hwid)
1550 break;
1551
1552 status = inb(port->ioaddr + UART_LSR);
1553 } while (status & UART_LSR_DR);
1554
1555 return status;
1556}
1557
1558static u8 mxser_receive_chars(struct tty_struct *tty,
1559 struct mxser_port *port, u8 status)
1560{
1561 if (!mxser_receive_chars_new(port, status))
1562 status = mxser_receive_chars_old(tty, port, status);
1563
1564 tty_flip_buffer_push(&port->port);
1565
1566 return status;
1567}
1568
1569static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
1570{
1571 int count;
1572
1573 if (port->x_char) {
1574 outb(port->x_char, port->ioaddr + UART_TX);
1575 port->x_char = 0;
1576 port->icount.tx++;
1577 return;
1578 }
1579
1580 if (kfifo_is_empty(&port->port.xmit_fifo) || tty->flow.stopped ||
1581 (tty->hw_stopped && !mxser_16550A_or_MUST(port))) {
1582 __mxser_stop_tx(port);
1583 return;
1584 }
1585
1586 count = port->xmit_fifo_size;
1587 do {
1588 u8 c;
1589
1590 if (!kfifo_get(&port->port.xmit_fifo, &c))
1591 break;
1592
1593 outb(c, port->ioaddr + UART_TX);
1594 port->icount.tx++;
1595 } while (--count > 0);
1596
1597 if (kfifo_len(&port->port.xmit_fifo) < WAKEUP_CHARS)
1598 tty_wakeup(tty);
1599
1600 if (kfifo_is_empty(&port->port.xmit_fifo))
1601 __mxser_stop_tx(port);
1602}
1603
1604static bool mxser_port_isr(struct mxser_port *port)
1605{
1606 struct tty_struct *tty;
1607 u8 iir, status;
1608 bool error = false;
1609
1610 iir = inb(port->ioaddr + UART_IIR);
1611 if (iir & UART_IIR_NO_INT)
1612 return true;
1613
1614 iir &= MOXA_MUST_IIR_MASK;
1615 tty = tty_port_tty_get(&port->port);
1616 if (!tty) {
1617 status = inb(port->ioaddr + UART_LSR);
1618 outb(port->FCR | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
1619 port->ioaddr + UART_FCR);
1620 inb(port->ioaddr + UART_MSR);
1621
1622 error = true;
1623 goto put_tty;
1624 }
1625
1626 status = inb(port->ioaddr + UART_LSR);
1627
1628 if (port->board->must_hwid) {
1629 if (iir == MOXA_MUST_IIR_GDA ||
1630 iir == MOXA_MUST_IIR_RDA ||
1631 iir == MOXA_MUST_IIR_RTO ||
1632 iir == MOXA_MUST_IIR_LSR)
1633 status = mxser_receive_chars(tty, port, status);
1634 } else {
1635 status &= port->read_status_mask;
1636 if (status & UART_LSR_DR)
1637 status = mxser_receive_chars(tty, port, status);
1638 }
1639
1640 mxser_check_modem_status(tty, port);
1641
1642 if (port->board->must_hwid) {
1643 if (iir == 0x02 && (status & UART_LSR_THRE))
1644 mxser_transmit_chars(tty, port);
1645 } else {
1646 if (status & UART_LSR_THRE)
1647 mxser_transmit_chars(tty, port);
1648 }
1649
1650put_tty:
1651 tty_kref_put(tty);
1652
1653 return error;
1654}
1655
1656/*
1657 * This is the serial driver's generic interrupt routine
1658 */
1659static irqreturn_t mxser_interrupt(int irq, void *dev_id)
1660{
1661 struct mxser_board *brd = dev_id;
1662 struct mxser_port *port;
1663 unsigned int int_cnt, pass_counter = 0;
1664 unsigned int i, max = brd->nports;
1665 int handled = IRQ_NONE;
1666 u8 irqbits, bits, mask = BIT(max) - 1;
1667
1668 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
1669 irqbits = inb(brd->vector) & mask;
1670 if (irqbits == mask)
1671 break;
1672
1673 handled = IRQ_HANDLED;
1674 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
1675 if (irqbits == mask)
1676 break;
1677 if (bits & irqbits)
1678 continue;
1679 port = &brd->ports[i];
1680
1681 int_cnt = 0;
1682 spin_lock(&port->slock);
1683 do {
1684 if (mxser_port_isr(port))
1685 break;
1686 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
1687 spin_unlock(&port->slock);
1688 }
1689 }
1690
1691 return handled;
1692}
1693
1694static const struct tty_operations mxser_ops = {
1695 .open = mxser_open,
1696 .close = mxser_close,
1697 .write = mxser_write,
1698 .put_char = mxser_put_char,
1699 .flush_chars = mxser_flush_chars,
1700 .write_room = mxser_write_room,
1701 .chars_in_buffer = mxser_chars_in_buffer,
1702 .flush_buffer = mxser_flush_buffer,
1703 .ioctl = mxser_ioctl,
1704 .throttle = mxser_throttle,
1705 .unthrottle = mxser_unthrottle,
1706 .set_termios = mxser_set_termios,
1707 .stop = mxser_stop,
1708 .start = mxser_start,
1709 .hangup = mxser_hangup,
1710 .break_ctl = mxser_rs_break,
1711 .wait_until_sent = mxser_wait_until_sent,
1712 .tiocmget = mxser_tiocmget,
1713 .tiocmset = mxser_tiocmset,
1714 .set_serial = mxser_set_serial_info,
1715 .get_serial = mxser_get_serial_info,
1716 .get_icount = mxser_get_icount,
1717};
1718
1719static const struct tty_port_operations mxser_port_ops = {
1720 .carrier_raised = mxser_carrier_raised,
1721 .dtr_rts = mxser_dtr_rts,
1722 .activate = mxser_activate,
1723 .shutdown = mxser_shutdown_port,
1724};
1725
1726/*
1727 * The MOXA Smartio/Industio serial driver boot-time initialization code!
1728 */
1729
1730static void mxser_initbrd(struct mxser_board *brd, bool high_baud)
1731{
1732 struct mxser_port *info;
1733 unsigned int i;
1734 bool is_mu860;
1735
1736 brd->must_hwid = mxser_must_get_hwid(brd->ports[0].ioaddr);
1737 is_mu860 = brd->must_hwid == MOXA_MUST_MU860_HWID;
1738
1739 for (i = 0; i < UART_INFO_NUM; i++) {
1740 if (Gpci_uart_info[i].type == brd->must_hwid) {
1741 brd->max_baud = Gpci_uart_info[i].max_baud;
1742
1743 /* exception....CP-102 */
1744 if (high_baud)
1745 brd->max_baud = 921600;
1746 break;
1747 }
1748 }
1749
1750 if (is_mu860) {
1751 /* set to RS232 mode by default */
1752 outb(0, brd->vector + 4);
1753 outb(0, brd->vector + 0x0c);
1754 }
1755
1756 for (i = 0; i < brd->nports; i++) {
1757 info = &brd->ports[i];
1758 if (is_mu860) {
1759 if (i < 4)
1760 info->opmode_ioaddr = brd->vector + 4;
1761 else
1762 info->opmode_ioaddr = brd->vector + 0x0c;
1763 }
1764 tty_port_init(&info->port);
1765 info->port.ops = &mxser_port_ops;
1766 info->board = brd;
1767
1768 /* Enhance mode enabled here */
1769 if (brd->must_hwid != MOXA_OTHER_UART)
1770 mxser_must_set_enhance_mode(info->ioaddr, true);
1771
1772 info->type = PORT_16550A;
1773
1774 mxser_process_txrx_fifo(info);
1775
1776 info->port.close_delay = 5 * HZ / 10;
1777 info->port.closing_wait = 30 * HZ;
1778 spin_lock_init(&info->slock);
1779
1780 /* before set INT ISR, disable all int */
1781 outb(inb(info->ioaddr + UART_IER) & 0xf0,
1782 info->ioaddr + UART_IER);
1783 }
1784}
1785
1786static int mxser_probe(struct pci_dev *pdev,
1787 const struct pci_device_id *ent)
1788{
1789 struct mxser_board *brd;
1790 unsigned int i, base;
1791 unsigned long ioaddress;
1792 unsigned short nports = MXSER_NPORTS(ent->driver_data);
1793 struct device *tty_dev;
1794 int retval = -EINVAL;
1795
1796 i = find_first_zero_bit(mxser_boards, MXSER_BOARDS);
1797 if (i >= MXSER_BOARDS) {
1798 dev_err(&pdev->dev, "too many boards found (maximum %d), board "
1799 "not configured\n", MXSER_BOARDS);
1800 goto err;
1801 }
1802
1803 brd = devm_kzalloc(&pdev->dev, struct_size(brd, ports, nports),
1804 GFP_KERNEL);
1805 if (!brd)
1806 goto err;
1807
1808 brd->idx = i;
1809 __set_bit(brd->idx, mxser_boards);
1810 base = i * MXSER_PORTS_PER_BOARD;
1811
1812 retval = pcim_enable_device(pdev);
1813 if (retval) {
1814 dev_err(&pdev->dev, "PCI enable failed\n");
1815 goto err_zero;
1816 }
1817
1818 /* io address */
1819 ioaddress = pci_resource_start(pdev, 2);
1820 retval = pci_request_region(pdev, 2, "mxser(IO)");
1821 if (retval)
1822 goto err_zero;
1823
1824 brd->nports = nports;
1825 for (i = 0; i < nports; i++)
1826 brd->ports[i].ioaddr = ioaddress + 8 * i;
1827
1828 /* vector */
1829 ioaddress = pci_resource_start(pdev, 3);
1830 retval = pci_request_region(pdev, 3, "mxser(vector)");
1831 if (retval)
1832 goto err_zero;
1833 brd->vector = ioaddress;
1834
1835 /* irq */
1836 brd->irq = pdev->irq;
1837
1838 mxser_initbrd(brd, ent->driver_data & MXSER_HIGHBAUD);
1839
1840 retval = devm_request_irq(&pdev->dev, brd->irq, mxser_interrupt,
1841 IRQF_SHARED, "mxser", brd);
1842 if (retval) {
1843 dev_err(&pdev->dev, "request irq failed");
1844 goto err_relbrd;
1845 }
1846
1847 for (i = 0; i < nports; i++) {
1848 tty_dev = tty_port_register_device(&brd->ports[i].port,
1849 mxvar_sdriver, base + i, &pdev->dev);
1850 if (IS_ERR(tty_dev)) {
1851 retval = PTR_ERR(tty_dev);
1852 for (; i > 0; i--)
1853 tty_unregister_device(mxvar_sdriver,
1854 base + i - 1);
1855 goto err_relbrd;
1856 }
1857 }
1858
1859 pci_set_drvdata(pdev, brd);
1860
1861 return 0;
1862err_relbrd:
1863 for (i = 0; i < nports; i++)
1864 tty_port_destroy(&brd->ports[i].port);
1865err_zero:
1866 __clear_bit(brd->idx, mxser_boards);
1867err:
1868 return retval;
1869}
1870
1871static void mxser_remove(struct pci_dev *pdev)
1872{
1873 struct mxser_board *brd = pci_get_drvdata(pdev);
1874 unsigned int i, base = brd->idx * MXSER_PORTS_PER_BOARD;
1875
1876 for (i = 0; i < brd->nports; i++) {
1877 tty_unregister_device(mxvar_sdriver, base + i);
1878 tty_port_destroy(&brd->ports[i].port);
1879 }
1880
1881 __clear_bit(brd->idx, mxser_boards);
1882}
1883
1884static struct pci_driver mxser_driver = {
1885 .name = "mxser",
1886 .id_table = mxser_pcibrds,
1887 .probe = mxser_probe,
1888 .remove = mxser_remove
1889};
1890
1891static int __init mxser_module_init(void)
1892{
1893 int retval;
1894
1895 mxvar_sdriver = tty_alloc_driver(MXSER_PORTS, TTY_DRIVER_REAL_RAW |
1896 TTY_DRIVER_DYNAMIC_DEV);
1897 if (IS_ERR(mxvar_sdriver))
1898 return PTR_ERR(mxvar_sdriver);
1899
1900 /* Initialize the tty_driver structure */
1901 mxvar_sdriver->name = "ttyMI";
1902 mxvar_sdriver->major = ttymajor;
1903 mxvar_sdriver->minor_start = 0;
1904 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
1905 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
1906 mxvar_sdriver->init_termios = tty_std_termios;
1907 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
1908 tty_set_operations(mxvar_sdriver, &mxser_ops);
1909
1910 retval = tty_register_driver(mxvar_sdriver);
1911 if (retval) {
1912 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
1913 "tty driver !\n");
1914 goto err_put;
1915 }
1916
1917 retval = pci_register_driver(&mxser_driver);
1918 if (retval) {
1919 printk(KERN_ERR "mxser: can't register pci driver\n");
1920 goto err_unr;
1921 }
1922
1923 return 0;
1924err_unr:
1925 tty_unregister_driver(mxvar_sdriver);
1926err_put:
1927 tty_driver_kref_put(mxvar_sdriver);
1928 return retval;
1929}
1930
1931static void __exit mxser_module_exit(void)
1932{
1933 pci_unregister_driver(&mxser_driver);
1934 tty_unregister_driver(mxvar_sdriver);
1935 tty_driver_kref_put(mxvar_sdriver);
1936}
1937
1938module_init(mxser_module_init);
1939module_exit(mxser_module_exit);
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * mxser.c -- MOXA Smartio/Industio family multiport serial driver.
4 *
5 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com).
6 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com>
7 *
8 * This code is loosely based on the 1.8 moxa driver which is based on
9 * Linux serial driver, written by Linus Torvalds, Theodore T'so and
10 * others.
11 *
12 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
13 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
14 * www.moxa.com.
15 * - Fixed x86_64 cleanness
16 */
17
18#include <linux/module.h>
19#include <linux/errno.h>
20#include <linux/signal.h>
21#include <linux/sched.h>
22#include <linux/timer.h>
23#include <linux/interrupt.h>
24#include <linux/tty.h>
25#include <linux/tty_flip.h>
26#include <linux/serial.h>
27#include <linux/serial_reg.h>
28#include <linux/major.h>
29#include <linux/string.h>
30#include <linux/fcntl.h>
31#include <linux/ptrace.h>
32#include <linux/ioport.h>
33#include <linux/mm.h>
34#include <linux/delay.h>
35#include <linux/pci.h>
36#include <linux/bitops.h>
37#include <linux/slab.h>
38#include <linux/ratelimit.h>
39
40#include <asm/io.h>
41#include <asm/irq.h>
42#include <linux/uaccess.h>
43
44#include "mxser.h"
45
46#define MXSER_VERSION "2.0.5" /* 1.14 */
47#define MXSERMAJOR 174
48
49#define MXSER_BOARDS 4 /* Max. boards */
50#define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */
51#define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
52#define MXSER_ISR_PASS_LIMIT 100
53
54/*CheckIsMoxaMust return value*/
55#define MOXA_OTHER_UART 0x00
56#define MOXA_MUST_MU150_HWID 0x01
57#define MOXA_MUST_MU860_HWID 0x02
58
59#define WAKEUP_CHARS 256
60
61#define UART_MCR_AFE 0x20
62#define UART_LSR_SPECIAL 0x1E
63
64#define PCI_DEVICE_ID_POS104UL 0x1044
65#define PCI_DEVICE_ID_CB108 0x1080
66#define PCI_DEVICE_ID_CP102UF 0x1023
67#define PCI_DEVICE_ID_CP112UL 0x1120
68#define PCI_DEVICE_ID_CB114 0x1142
69#define PCI_DEVICE_ID_CP114UL 0x1143
70#define PCI_DEVICE_ID_CB134I 0x1341
71#define PCI_DEVICE_ID_CP138U 0x1380
72
73
74#define C168_ASIC_ID 1
75#define C104_ASIC_ID 2
76#define C102_ASIC_ID 0xB
77#define CI132_ASIC_ID 4
78#define CI134_ASIC_ID 3
79#define CI104J_ASIC_ID 5
80
81#define MXSER_HIGHBAUD 1
82#define MXSER_HAS2 2
83
84/* This is only for PCI */
85static const struct {
86 int type;
87 int tx_fifo;
88 int rx_fifo;
89 int xmit_fifo_size;
90 int rx_high_water;
91 int rx_trigger;
92 int rx_low_water;
93 long max_baud;
94} Gpci_uart_info[] = {
95 {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L},
96 {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L},
97 {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L}
98};
99#define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info)
100
101struct mxser_cardinfo {
102 char *name;
103 unsigned int nports;
104 unsigned int flags;
105};
106
107static const struct mxser_cardinfo mxser_cards[] = {
108/* 0*/ { "C168 series", 8, },
109 { "C104 series", 4, },
110 { "CI-104J series", 4, },
111 { "C168H/PCI series", 8, },
112 { "C104H/PCI series", 4, },
113/* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */
114 { "CI-132 series", 4, MXSER_HAS2 },
115 { "CI-134 series", 4, },
116 { "CP-132 series", 2, },
117 { "CP-114 series", 4, },
118/*10*/ { "CT-114 series", 4, },
119 { "CP-102 series", 2, MXSER_HIGHBAUD },
120 { "CP-104U series", 4, },
121 { "CP-168U series", 8, },
122 { "CP-132U series", 2, },
123/*15*/ { "CP-134U series", 4, },
124 { "CP-104JU series", 4, },
125 { "Moxa UC7000 Serial", 8, }, /* RC7000 */
126 { "CP-118U series", 8, },
127 { "CP-102UL series", 2, },
128/*20*/ { "CP-102U series", 2, },
129 { "CP-118EL series", 8, },
130 { "CP-168EL series", 8, },
131 { "CP-104EL series", 4, },
132 { "CB-108 series", 8, },
133/*25*/ { "CB-114 series", 4, },
134 { "CB-134I series", 4, },
135 { "CP-138U series", 8, },
136 { "POS-104UL series", 4, },
137 { "CP-114UL series", 4, },
138/*30*/ { "CP-102UF series", 2, },
139 { "CP-112UL series", 2, },
140};
141
142/* driver_data correspond to the lines in the structure above
143 see also ISA probe function before you change something */
144static const struct pci_device_id mxser_pcibrds[] = {
145 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 },
146 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 },
147 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 },
148 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 },
149 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 },
150 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 },
151 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 },
152 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 },
153 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 },
154 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 },
155 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 },
156 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 },
157 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 },
158 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 },
159 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 },
160 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 },
161 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 },
162 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 },
163 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 },
164 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 },
165 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 },
166 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 },
167 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 },
168 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 },
169 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF), .driver_data = 30 },
170 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL), .driver_data = 31 },
171 { }
172};
173MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
174
175static unsigned long ioaddr[MXSER_BOARDS];
176static int ttymajor = MXSERMAJOR;
177
178/* Variables for insmod */
179
180MODULE_AUTHOR("Casper Yang");
181MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
182module_param_hw_array(ioaddr, ulong, ioport, NULL, 0);
183MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board");
184module_param(ttymajor, int, 0);
185MODULE_LICENSE("GPL");
186
187struct mxser_log {
188 int tick;
189 unsigned long rxcnt[MXSER_PORTS];
190 unsigned long txcnt[MXSER_PORTS];
191};
192
193struct mxser_mon {
194 unsigned long rxcnt;
195 unsigned long txcnt;
196 unsigned long up_rxcnt;
197 unsigned long up_txcnt;
198 int modem_status;
199 unsigned char hold_reason;
200};
201
202struct mxser_mon_ext {
203 unsigned long rx_cnt[32];
204 unsigned long tx_cnt[32];
205 unsigned long up_rxcnt[32];
206 unsigned long up_txcnt[32];
207 int modem_status[32];
208
209 long baudrate[32];
210 int databits[32];
211 int stopbits[32];
212 int parity[32];
213 int flowctrl[32];
214 int fifo[32];
215 int iftype[32];
216};
217
218struct mxser_board;
219
220struct mxser_port {
221 struct tty_port port;
222 struct mxser_board *board;
223
224 unsigned long ioaddr;
225 unsigned long opmode_ioaddr;
226 int max_baud;
227
228 int rx_high_water;
229 int rx_trigger; /* Rx fifo trigger level */
230 int rx_low_water;
231 int baud_base; /* max. speed */
232 int type; /* UART type */
233
234 int x_char; /* xon/xoff character */
235 int IER; /* Interrupt Enable Register */
236 int MCR; /* Modem control register */
237
238 unsigned char stop_rx;
239 unsigned char ldisc_stop_rx;
240
241 int custom_divisor;
242 unsigned char err_shadow;
243
244 struct async_icount icount; /* kernel counters for 4 input interrupts */
245 unsigned int timeout;
246
247 int read_status_mask;
248 int ignore_status_mask;
249 unsigned int xmit_fifo_size;
250 int xmit_head;
251 int xmit_tail;
252 int xmit_cnt;
253 int closing;
254
255 struct ktermios normal_termios;
256
257 struct mxser_mon mon_data;
258
259 spinlock_t slock;
260};
261
262struct mxser_board {
263 unsigned int idx;
264 int irq;
265 const struct mxser_cardinfo *info;
266 unsigned long vector;
267 unsigned long vector_mask;
268
269 int chip_flag;
270 int uart_type;
271
272 struct mxser_port ports[MXSER_PORTS_PER_BOARD];
273};
274
275struct mxser_mstatus {
276 tcflag_t cflag;
277 int cts;
278 int dsr;
279 int ri;
280 int dcd;
281};
282
283static struct mxser_board mxser_boards[MXSER_BOARDS];
284static struct tty_driver *mxvar_sdriver;
285static struct mxser_log mxvar_log;
286static int mxser_set_baud_method[MXSER_PORTS + 1];
287
288static void mxser_enable_must_enchance_mode(unsigned long baseio)
289{
290 u8 oldlcr;
291 u8 efr;
292
293 oldlcr = inb(baseio + UART_LCR);
294 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
295
296 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
297 efr |= MOXA_MUST_EFR_EFRB_ENABLE;
298
299 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
300 outb(oldlcr, baseio + UART_LCR);
301}
302
303#ifdef CONFIG_PCI
304static void mxser_disable_must_enchance_mode(unsigned long baseio)
305{
306 u8 oldlcr;
307 u8 efr;
308
309 oldlcr = inb(baseio + UART_LCR);
310 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
311
312 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
313 efr &= ~MOXA_MUST_EFR_EFRB_ENABLE;
314
315 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
316 outb(oldlcr, baseio + UART_LCR);
317}
318#endif
319
320static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
321{
322 u8 oldlcr;
323 u8 efr;
324
325 oldlcr = inb(baseio + UART_LCR);
326 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
327
328 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
329 efr &= ~MOXA_MUST_EFR_BANK_MASK;
330 efr |= MOXA_MUST_EFR_BANK0;
331
332 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
333 outb(value, baseio + MOXA_MUST_XON1_REGISTER);
334 outb(oldlcr, baseio + UART_LCR);
335}
336
337static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
338{
339 u8 oldlcr;
340 u8 efr;
341
342 oldlcr = inb(baseio + UART_LCR);
343 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
344
345 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
346 efr &= ~MOXA_MUST_EFR_BANK_MASK;
347 efr |= MOXA_MUST_EFR_BANK0;
348
349 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
350 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
351 outb(oldlcr, baseio + UART_LCR);
352}
353
354static void mxser_set_must_fifo_value(struct mxser_port *info)
355{
356 u8 oldlcr;
357 u8 efr;
358
359 oldlcr = inb(info->ioaddr + UART_LCR);
360 outb(MOXA_MUST_ENTER_ENCHANCE, info->ioaddr + UART_LCR);
361
362 efr = inb(info->ioaddr + MOXA_MUST_EFR_REGISTER);
363 efr &= ~MOXA_MUST_EFR_BANK_MASK;
364 efr |= MOXA_MUST_EFR_BANK1;
365
366 outb(efr, info->ioaddr + MOXA_MUST_EFR_REGISTER);
367 outb((u8)info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
368 outb((u8)info->rx_trigger, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
369 outb((u8)info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
370 outb(oldlcr, info->ioaddr + UART_LCR);
371}
372
373static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
374{
375 u8 oldlcr;
376 u8 efr;
377
378 oldlcr = inb(baseio + UART_LCR);
379 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
380
381 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
382 efr &= ~MOXA_MUST_EFR_BANK_MASK;
383 efr |= MOXA_MUST_EFR_BANK2;
384
385 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
386 outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
387 outb(oldlcr, baseio + UART_LCR);
388}
389
390#ifdef CONFIG_PCI
391static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId)
392{
393 u8 oldlcr;
394 u8 efr;
395
396 oldlcr = inb(baseio + UART_LCR);
397 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
398
399 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
400 efr &= ~MOXA_MUST_EFR_BANK_MASK;
401 efr |= MOXA_MUST_EFR_BANK2;
402
403 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
404 *pId = inb(baseio + MOXA_MUST_HWID_REGISTER);
405 outb(oldlcr, baseio + UART_LCR);
406}
407#endif
408
409static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio)
410{
411 u8 oldlcr;
412 u8 efr;
413
414 oldlcr = inb(baseio + UART_LCR);
415 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
416
417 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
418 efr &= ~MOXA_MUST_EFR_SF_MASK;
419
420 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
421 outb(oldlcr, baseio + UART_LCR);
422}
423
424static void mxser_enable_must_tx_software_flow_control(unsigned long baseio)
425{
426 u8 oldlcr;
427 u8 efr;
428
429 oldlcr = inb(baseio + UART_LCR);
430 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
431
432 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
433 efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
434 efr |= MOXA_MUST_EFR_SF_TX1;
435
436 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
437 outb(oldlcr, baseio + UART_LCR);
438}
439
440static void mxser_disable_must_tx_software_flow_control(unsigned long baseio)
441{
442 u8 oldlcr;
443 u8 efr;
444
445 oldlcr = inb(baseio + UART_LCR);
446 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
447
448 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
449 efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
450
451 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
452 outb(oldlcr, baseio + UART_LCR);
453}
454
455static void mxser_enable_must_rx_software_flow_control(unsigned long baseio)
456{
457 u8 oldlcr;
458 u8 efr;
459
460 oldlcr = inb(baseio + UART_LCR);
461 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
462
463 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
464 efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
465 efr |= MOXA_MUST_EFR_SF_RX1;
466
467 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
468 outb(oldlcr, baseio + UART_LCR);
469}
470
471static void mxser_disable_must_rx_software_flow_control(unsigned long baseio)
472{
473 u8 oldlcr;
474 u8 efr;
475
476 oldlcr = inb(baseio + UART_LCR);
477 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
478
479 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
480 efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
481
482 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
483 outb(oldlcr, baseio + UART_LCR);
484}
485
486#ifdef CONFIG_PCI
487static int CheckIsMoxaMust(unsigned long io)
488{
489 u8 oldmcr, hwid;
490 int i;
491
492 outb(0, io + UART_LCR);
493 mxser_disable_must_enchance_mode(io);
494 oldmcr = inb(io + UART_MCR);
495 outb(0, io + UART_MCR);
496 mxser_set_must_xon1_value(io, 0x11);
497 if ((hwid = inb(io + UART_MCR)) != 0) {
498 outb(oldmcr, io + UART_MCR);
499 return MOXA_OTHER_UART;
500 }
501
502 mxser_get_must_hardware_id(io, &hwid);
503 for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */
504 if (hwid == Gpci_uart_info[i].type)
505 return (int)hwid;
506 }
507 return MOXA_OTHER_UART;
508}
509#endif
510
511static void process_txrx_fifo(struct mxser_port *info)
512{
513 int i;
514
515 if ((info->type == PORT_16450) || (info->type == PORT_8250)) {
516 info->rx_trigger = 1;
517 info->rx_high_water = 1;
518 info->rx_low_water = 1;
519 info->xmit_fifo_size = 1;
520 } else
521 for (i = 0; i < UART_INFO_NUM; i++)
522 if (info->board->chip_flag == Gpci_uart_info[i].type) {
523 info->rx_trigger = Gpci_uart_info[i].rx_trigger;
524 info->rx_low_water = Gpci_uart_info[i].rx_low_water;
525 info->rx_high_water = Gpci_uart_info[i].rx_high_water;
526 info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size;
527 break;
528 }
529}
530
531static unsigned char mxser_get_msr(int baseaddr, int mode, int port)
532{
533 static unsigned char mxser_msr[MXSER_PORTS + 1];
534 unsigned char status = 0;
535
536 status = inb(baseaddr + UART_MSR);
537
538 mxser_msr[port] &= 0x0F;
539 mxser_msr[port] |= status;
540 status = mxser_msr[port];
541 if (mode)
542 mxser_msr[port] = 0;
543
544 return status;
545}
546
547static int mxser_carrier_raised(struct tty_port *port)
548{
549 struct mxser_port *mp = container_of(port, struct mxser_port, port);
550 return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0;
551}
552
553static void mxser_dtr_rts(struct tty_port *port, int on)
554{
555 struct mxser_port *mp = container_of(port, struct mxser_port, port);
556 unsigned long flags;
557
558 spin_lock_irqsave(&mp->slock, flags);
559 if (on)
560 outb(inb(mp->ioaddr + UART_MCR) |
561 UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR);
562 else
563 outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS),
564 mp->ioaddr + UART_MCR);
565 spin_unlock_irqrestore(&mp->slock, flags);
566}
567
568static int mxser_set_baud(struct tty_struct *tty, long newspd)
569{
570 struct mxser_port *info = tty->driver_data;
571 unsigned int quot = 0, baud;
572 unsigned char cval;
573 u64 timeout;
574
575 if (!info->ioaddr)
576 return -1;
577
578 if (newspd > info->max_baud)
579 return -1;
580
581 if (newspd == 134) {
582 quot = 2 * info->baud_base / 269;
583 tty_encode_baud_rate(tty, 134, 134);
584 } else if (newspd) {
585 quot = info->baud_base / newspd;
586 if (quot == 0)
587 quot = 1;
588 baud = info->baud_base/quot;
589 tty_encode_baud_rate(tty, baud, baud);
590 } else {
591 quot = 0;
592 }
593
594 /*
595 * worst case (128 * 1000 * 10 * 18432) needs 35 bits, so divide in the
596 * u64 domain
597 */
598 timeout = (u64)info->xmit_fifo_size * HZ * 10 * quot;
599 do_div(timeout, info->baud_base);
600 info->timeout = timeout + HZ / 50; /* Add .02 seconds of slop */
601
602 if (quot) {
603 info->MCR |= UART_MCR_DTR;
604 outb(info->MCR, info->ioaddr + UART_MCR);
605 } else {
606 info->MCR &= ~UART_MCR_DTR;
607 outb(info->MCR, info->ioaddr + UART_MCR);
608 return 0;
609 }
610
611 cval = inb(info->ioaddr + UART_LCR);
612
613 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
614
615 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
616 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
617 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
618
619#ifdef BOTHER
620 if (C_BAUD(tty) == BOTHER) {
621 quot = info->baud_base % newspd;
622 quot *= 8;
623 if (quot % newspd > newspd / 2) {
624 quot /= newspd;
625 quot++;
626 } else
627 quot /= newspd;
628
629 mxser_set_must_enum_value(info->ioaddr, quot);
630 } else
631#endif
632 mxser_set_must_enum_value(info->ioaddr, 0);
633
634 return 0;
635}
636
637/*
638 * This routine is called to set the UART divisor registers to match
639 * the specified baud rate for a serial port.
640 */
641static int mxser_change_speed(struct tty_struct *tty)
642{
643 struct mxser_port *info = tty->driver_data;
644 unsigned cflag, cval, fcr;
645 int ret = 0;
646 unsigned char status;
647
648 cflag = tty->termios.c_cflag;
649 if (!info->ioaddr)
650 return ret;
651
652 if (mxser_set_baud_method[tty->index] == 0)
653 mxser_set_baud(tty, tty_get_baud_rate(tty));
654
655 /* byte size and parity */
656 switch (cflag & CSIZE) {
657 case CS5:
658 cval = 0x00;
659 break;
660 case CS6:
661 cval = 0x01;
662 break;
663 case CS7:
664 cval = 0x02;
665 break;
666 case CS8:
667 cval = 0x03;
668 break;
669 default:
670 cval = 0x00;
671 break; /* too keep GCC shut... */
672 }
673 if (cflag & CSTOPB)
674 cval |= 0x04;
675 if (cflag & PARENB)
676 cval |= UART_LCR_PARITY;
677 if (!(cflag & PARODD))
678 cval |= UART_LCR_EPAR;
679 if (cflag & CMSPAR)
680 cval |= UART_LCR_SPAR;
681
682 if ((info->type == PORT_8250) || (info->type == PORT_16450)) {
683 if (info->board->chip_flag) {
684 fcr = UART_FCR_ENABLE_FIFO;
685 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
686 mxser_set_must_fifo_value(info);
687 } else
688 fcr = 0;
689 } else {
690 fcr = UART_FCR_ENABLE_FIFO;
691 if (info->board->chip_flag) {
692 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
693 mxser_set_must_fifo_value(info);
694 } else {
695 switch (info->rx_trigger) {
696 case 1:
697 fcr |= UART_FCR_TRIGGER_1;
698 break;
699 case 4:
700 fcr |= UART_FCR_TRIGGER_4;
701 break;
702 case 8:
703 fcr |= UART_FCR_TRIGGER_8;
704 break;
705 default:
706 fcr |= UART_FCR_TRIGGER_14;
707 break;
708 }
709 }
710 }
711
712 /* CTS flow control flag and modem status interrupts */
713 info->IER &= ~UART_IER_MSI;
714 info->MCR &= ~UART_MCR_AFE;
715 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
716 if (cflag & CRTSCTS) {
717 info->IER |= UART_IER_MSI;
718 if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
719 info->MCR |= UART_MCR_AFE;
720 } else {
721 status = inb(info->ioaddr + UART_MSR);
722 if (tty->hw_stopped) {
723 if (status & UART_MSR_CTS) {
724 tty->hw_stopped = 0;
725 if (info->type != PORT_16550A &&
726 !info->board->chip_flag) {
727 outb(info->IER & ~UART_IER_THRI,
728 info->ioaddr +
729 UART_IER);
730 info->IER |= UART_IER_THRI;
731 outb(info->IER, info->ioaddr +
732 UART_IER);
733 }
734 tty_wakeup(tty);
735 }
736 } else {
737 if (!(status & UART_MSR_CTS)) {
738 tty->hw_stopped = 1;
739 if ((info->type != PORT_16550A) &&
740 (!info->board->chip_flag)) {
741 info->IER &= ~UART_IER_THRI;
742 outb(info->IER, info->ioaddr +
743 UART_IER);
744 }
745 }
746 }
747 }
748 }
749 outb(info->MCR, info->ioaddr + UART_MCR);
750 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
751 if (~cflag & CLOCAL)
752 info->IER |= UART_IER_MSI;
753 outb(info->IER, info->ioaddr + UART_IER);
754
755 /*
756 * Set up parity check flag
757 */
758 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
759 if (I_INPCK(tty))
760 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
761 if (I_BRKINT(tty) || I_PARMRK(tty))
762 info->read_status_mask |= UART_LSR_BI;
763
764 info->ignore_status_mask = 0;
765
766 if (I_IGNBRK(tty)) {
767 info->ignore_status_mask |= UART_LSR_BI;
768 info->read_status_mask |= UART_LSR_BI;
769 /*
770 * If we're ignore parity and break indicators, ignore
771 * overruns too. (For real raw support).
772 */
773 if (I_IGNPAR(tty)) {
774 info->ignore_status_mask |=
775 UART_LSR_OE |
776 UART_LSR_PE |
777 UART_LSR_FE;
778 info->read_status_mask |=
779 UART_LSR_OE |
780 UART_LSR_PE |
781 UART_LSR_FE;
782 }
783 }
784 if (info->board->chip_flag) {
785 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
786 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
787 if (I_IXON(tty)) {
788 mxser_enable_must_rx_software_flow_control(
789 info->ioaddr);
790 } else {
791 mxser_disable_must_rx_software_flow_control(
792 info->ioaddr);
793 }
794 if (I_IXOFF(tty)) {
795 mxser_enable_must_tx_software_flow_control(
796 info->ioaddr);
797 } else {
798 mxser_disable_must_tx_software_flow_control(
799 info->ioaddr);
800 }
801 }
802
803
804 outb(fcr, info->ioaddr + UART_FCR); /* set fcr */
805 outb(cval, info->ioaddr + UART_LCR);
806
807 return ret;
808}
809
810static void mxser_check_modem_status(struct tty_struct *tty,
811 struct mxser_port *port, int status)
812{
813 /* update input line counters */
814 if (status & UART_MSR_TERI)
815 port->icount.rng++;
816 if (status & UART_MSR_DDSR)
817 port->icount.dsr++;
818 if (status & UART_MSR_DDCD)
819 port->icount.dcd++;
820 if (status & UART_MSR_DCTS)
821 port->icount.cts++;
822 port->mon_data.modem_status = status;
823 wake_up_interruptible(&port->port.delta_msr_wait);
824
825 if (tty_port_check_carrier(&port->port) && (status & UART_MSR_DDCD)) {
826 if (status & UART_MSR_DCD)
827 wake_up_interruptible(&port->port.open_wait);
828 }
829
830 if (tty_port_cts_enabled(&port->port)) {
831 if (tty->hw_stopped) {
832 if (status & UART_MSR_CTS) {
833 tty->hw_stopped = 0;
834
835 if ((port->type != PORT_16550A) &&
836 (!port->board->chip_flag)) {
837 outb(port->IER & ~UART_IER_THRI,
838 port->ioaddr + UART_IER);
839 port->IER |= UART_IER_THRI;
840 outb(port->IER, port->ioaddr +
841 UART_IER);
842 }
843 tty_wakeup(tty);
844 }
845 } else {
846 if (!(status & UART_MSR_CTS)) {
847 tty->hw_stopped = 1;
848 if (port->type != PORT_16550A &&
849 !port->board->chip_flag) {
850 port->IER &= ~UART_IER_THRI;
851 outb(port->IER, port->ioaddr +
852 UART_IER);
853 }
854 }
855 }
856 }
857}
858
859static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
860{
861 struct mxser_port *info = container_of(port, struct mxser_port, port);
862 unsigned long page;
863 unsigned long flags;
864
865 page = __get_free_page(GFP_KERNEL);
866 if (!page)
867 return -ENOMEM;
868
869 spin_lock_irqsave(&info->slock, flags);
870
871 if (!info->ioaddr || !info->type) {
872 set_bit(TTY_IO_ERROR, &tty->flags);
873 free_page(page);
874 spin_unlock_irqrestore(&info->slock, flags);
875 return 0;
876 }
877 info->port.xmit_buf = (unsigned char *) page;
878
879 /*
880 * Clear the FIFO buffers and disable them
881 * (they will be reenabled in mxser_change_speed())
882 */
883 if (info->board->chip_flag)
884 outb((UART_FCR_CLEAR_RCVR |
885 UART_FCR_CLEAR_XMIT |
886 MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR);
887 else
888 outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
889 info->ioaddr + UART_FCR);
890
891 /*
892 * At this point there's no way the LSR could still be 0xFF;
893 * if it is, then bail out, because there's likely no UART
894 * here.
895 */
896 if (inb(info->ioaddr + UART_LSR) == 0xff) {
897 spin_unlock_irqrestore(&info->slock, flags);
898 if (capable(CAP_SYS_ADMIN)) {
899 set_bit(TTY_IO_ERROR, &tty->flags);
900 return 0;
901 } else
902 return -ENODEV;
903 }
904
905 /*
906 * Clear the interrupt registers.
907 */
908 (void) inb(info->ioaddr + UART_LSR);
909 (void) inb(info->ioaddr + UART_RX);
910 (void) inb(info->ioaddr + UART_IIR);
911 (void) inb(info->ioaddr + UART_MSR);
912
913 /*
914 * Now, initialize the UART
915 */
916 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
917 info->MCR = UART_MCR_DTR | UART_MCR_RTS;
918 outb(info->MCR, info->ioaddr + UART_MCR);
919
920 /*
921 * Finally, enable interrupts
922 */
923 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
924
925 if (info->board->chip_flag)
926 info->IER |= MOXA_MUST_IER_EGDAI;
927 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */
928
929 /*
930 * And clear the interrupt registers again for luck.
931 */
932 (void) inb(info->ioaddr + UART_LSR);
933 (void) inb(info->ioaddr + UART_RX);
934 (void) inb(info->ioaddr + UART_IIR);
935 (void) inb(info->ioaddr + UART_MSR);
936
937 clear_bit(TTY_IO_ERROR, &tty->flags);
938 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
939
940 /*
941 * and set the speed of the serial port
942 */
943 mxser_change_speed(tty);
944 spin_unlock_irqrestore(&info->slock, flags);
945
946 return 0;
947}
948
949/*
950 * This routine will shutdown a serial port
951 */
952static void mxser_shutdown_port(struct tty_port *port)
953{
954 struct mxser_port *info = container_of(port, struct mxser_port, port);
955 unsigned long flags;
956
957 spin_lock_irqsave(&info->slock, flags);
958
959 /*
960 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
961 * here so the queue might never be waken up
962 */
963 wake_up_interruptible(&info->port.delta_msr_wait);
964
965 /*
966 * Free the xmit buffer, if necessary
967 */
968 if (info->port.xmit_buf) {
969 free_page((unsigned long) info->port.xmit_buf);
970 info->port.xmit_buf = NULL;
971 }
972
973 info->IER = 0;
974 outb(0x00, info->ioaddr + UART_IER);
975
976 /* clear Rx/Tx FIFO's */
977 if (info->board->chip_flag)
978 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
979 MOXA_MUST_FCR_GDA_MODE_ENABLE,
980 info->ioaddr + UART_FCR);
981 else
982 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
983 info->ioaddr + UART_FCR);
984
985 /* read data port to reset things */
986 (void) inb(info->ioaddr + UART_RX);
987
988
989 if (info->board->chip_flag)
990 SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr);
991
992 spin_unlock_irqrestore(&info->slock, flags);
993}
994
995/*
996 * This routine is called whenever a serial port is opened. It
997 * enables interrupts for a serial port, linking in its async structure into
998 * the IRQ chain. It also performs the serial-specific
999 * initialization for the tty structure.
1000 */
1001static int mxser_open(struct tty_struct *tty, struct file *filp)
1002{
1003 struct mxser_port *info;
1004 int line;
1005
1006 line = tty->index;
1007 if (line == MXSER_PORTS)
1008 return 0;
1009 info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD];
1010 if (!info->ioaddr)
1011 return -ENODEV;
1012
1013 tty->driver_data = info;
1014 return tty_port_open(&info->port, tty, filp);
1015}
1016
1017static void mxser_flush_buffer(struct tty_struct *tty)
1018{
1019 struct mxser_port *info = tty->driver_data;
1020 char fcr;
1021 unsigned long flags;
1022
1023
1024 spin_lock_irqsave(&info->slock, flags);
1025 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1026
1027 fcr = inb(info->ioaddr + UART_FCR);
1028 outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
1029 info->ioaddr + UART_FCR);
1030 outb(fcr, info->ioaddr + UART_FCR);
1031
1032 spin_unlock_irqrestore(&info->slock, flags);
1033
1034 tty_wakeup(tty);
1035}
1036
1037
1038static void mxser_close_port(struct tty_port *port)
1039{
1040 struct mxser_port *info = container_of(port, struct mxser_port, port);
1041 unsigned long timeout;
1042 /*
1043 * At this point we stop accepting input. To do this, we
1044 * disable the receive line status interrupts, and tell the
1045 * interrupt driver to stop checking the data ready bit in the
1046 * line status register.
1047 */
1048 info->IER &= ~UART_IER_RLSI;
1049 if (info->board->chip_flag)
1050 info->IER &= ~MOXA_MUST_RECV_ISR;
1051
1052 outb(info->IER, info->ioaddr + UART_IER);
1053 /*
1054 * Before we drop DTR, make sure the UART transmitter
1055 * has completely drained; this is especially
1056 * important if there is a transmit FIFO!
1057 */
1058 timeout = jiffies + HZ;
1059 while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) {
1060 schedule_timeout_interruptible(5);
1061 if (time_after(jiffies, timeout))
1062 break;
1063 }
1064}
1065
1066/*
1067 * This routine is called when the serial port gets closed. First, we
1068 * wait for the last remaining data to be sent. Then, we unlink its
1069 * async structure from the interrupt chain if necessary, and we free
1070 * that IRQ if nothing is left in the chain.
1071 */
1072static void mxser_close(struct tty_struct *tty, struct file *filp)
1073{
1074 struct mxser_port *info = tty->driver_data;
1075 struct tty_port *port = &info->port;
1076
1077 if (tty->index == MXSER_PORTS || info == NULL)
1078 return;
1079 if (tty_port_close_start(port, tty, filp) == 0)
1080 return;
1081 info->closing = 1;
1082 mutex_lock(&port->mutex);
1083 mxser_close_port(port);
1084 mxser_flush_buffer(tty);
1085 if (tty_port_initialized(port) && C_HUPCL(tty))
1086 tty_port_lower_dtr_rts(port);
1087 mxser_shutdown_port(port);
1088 tty_port_set_initialized(port, 0);
1089 mutex_unlock(&port->mutex);
1090 info->closing = 0;
1091 /* Right now the tty_port set is done outside of the close_end helper
1092 as we don't yet have everyone using refcounts */
1093 tty_port_close_end(port, tty);
1094 tty_port_tty_set(port, NULL);
1095}
1096
1097static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count)
1098{
1099 int c, total = 0;
1100 struct mxser_port *info = tty->driver_data;
1101 unsigned long flags;
1102
1103 if (!info->port.xmit_buf)
1104 return 0;
1105
1106 while (1) {
1107 c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
1108 SERIAL_XMIT_SIZE - info->xmit_head));
1109 if (c <= 0)
1110 break;
1111
1112 memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
1113 spin_lock_irqsave(&info->slock, flags);
1114 info->xmit_head = (info->xmit_head + c) &
1115 (SERIAL_XMIT_SIZE - 1);
1116 info->xmit_cnt += c;
1117 spin_unlock_irqrestore(&info->slock, flags);
1118
1119 buf += c;
1120 count -= c;
1121 total += c;
1122 }
1123
1124 if (info->xmit_cnt && !tty->stopped) {
1125 if (!tty->hw_stopped ||
1126 (info->type == PORT_16550A) ||
1127 (info->board->chip_flag)) {
1128 spin_lock_irqsave(&info->slock, flags);
1129 outb(info->IER & ~UART_IER_THRI, info->ioaddr +
1130 UART_IER);
1131 info->IER |= UART_IER_THRI;
1132 outb(info->IER, info->ioaddr + UART_IER);
1133 spin_unlock_irqrestore(&info->slock, flags);
1134 }
1135 }
1136 return total;
1137}
1138
1139static int mxser_put_char(struct tty_struct *tty, unsigned char ch)
1140{
1141 struct mxser_port *info = tty->driver_data;
1142 unsigned long flags;
1143
1144 if (!info->port.xmit_buf)
1145 return 0;
1146
1147 if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1)
1148 return 0;
1149
1150 spin_lock_irqsave(&info->slock, flags);
1151 info->port.xmit_buf[info->xmit_head++] = ch;
1152 info->xmit_head &= SERIAL_XMIT_SIZE - 1;
1153 info->xmit_cnt++;
1154 spin_unlock_irqrestore(&info->slock, flags);
1155 if (!tty->stopped) {
1156 if (!tty->hw_stopped ||
1157 (info->type == PORT_16550A) ||
1158 info->board->chip_flag) {
1159 spin_lock_irqsave(&info->slock, flags);
1160 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1161 info->IER |= UART_IER_THRI;
1162 outb(info->IER, info->ioaddr + UART_IER);
1163 spin_unlock_irqrestore(&info->slock, flags);
1164 }
1165 }
1166 return 1;
1167}
1168
1169
1170static void mxser_flush_chars(struct tty_struct *tty)
1171{
1172 struct mxser_port *info = tty->driver_data;
1173 unsigned long flags;
1174
1175 if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf ||
1176 (tty->hw_stopped && info->type != PORT_16550A &&
1177 !info->board->chip_flag))
1178 return;
1179
1180 spin_lock_irqsave(&info->slock, flags);
1181
1182 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1183 info->IER |= UART_IER_THRI;
1184 outb(info->IER, info->ioaddr + UART_IER);
1185
1186 spin_unlock_irqrestore(&info->slock, flags);
1187}
1188
1189static int mxser_write_room(struct tty_struct *tty)
1190{
1191 struct mxser_port *info = tty->driver_data;
1192 int ret;
1193
1194 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
1195 return ret < 0 ? 0 : ret;
1196}
1197
1198static int mxser_chars_in_buffer(struct tty_struct *tty)
1199{
1200 struct mxser_port *info = tty->driver_data;
1201 return info->xmit_cnt;
1202}
1203
1204/*
1205 * ------------------------------------------------------------
1206 * friends of mxser_ioctl()
1207 * ------------------------------------------------------------
1208 */
1209static int mxser_get_serial_info(struct tty_struct *tty,
1210 struct serial_struct __user *retinfo)
1211{
1212 struct mxser_port *info = tty->driver_data;
1213 struct serial_struct tmp = {
1214 .type = info->type,
1215 .line = tty->index,
1216 .port = info->ioaddr,
1217 .irq = info->board->irq,
1218 .flags = info->port.flags,
1219 .baud_base = info->baud_base,
1220 .close_delay = info->port.close_delay,
1221 .closing_wait = info->port.closing_wait,
1222 .custom_divisor = info->custom_divisor,
1223 };
1224 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1225 return -EFAULT;
1226 return 0;
1227}
1228
1229static int mxser_set_serial_info(struct tty_struct *tty,
1230 struct serial_struct __user *new_info)
1231{
1232 struct mxser_port *info = tty->driver_data;
1233 struct tty_port *port = &info->port;
1234 struct serial_struct new_serial;
1235 speed_t baud;
1236 unsigned long sl_flags;
1237 unsigned int flags;
1238 int retval = 0;
1239
1240 if (!new_info || !info->ioaddr)
1241 return -ENODEV;
1242 if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
1243 return -EFAULT;
1244
1245 if (new_serial.irq != info->board->irq ||
1246 new_serial.port != info->ioaddr)
1247 return -EINVAL;
1248
1249 flags = port->flags & ASYNC_SPD_MASK;
1250
1251 if (!capable(CAP_SYS_ADMIN)) {
1252 if ((new_serial.baud_base != info->baud_base) ||
1253 (new_serial.close_delay != info->port.close_delay) ||
1254 ((new_serial.flags & ~ASYNC_USR_MASK) != (info->port.flags & ~ASYNC_USR_MASK)))
1255 return -EPERM;
1256 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
1257 (new_serial.flags & ASYNC_USR_MASK));
1258 } else {
1259 /*
1260 * OK, past this point, all the error checking has been done.
1261 * At this point, we start making changes.....
1262 */
1263 port->flags = ((port->flags & ~ASYNC_FLAGS) |
1264 (new_serial.flags & ASYNC_FLAGS));
1265 port->close_delay = new_serial.close_delay * HZ / 100;
1266 port->closing_wait = new_serial.closing_wait * HZ / 100;
1267 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
1268 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
1269 (new_serial.baud_base != info->baud_base ||
1270 new_serial.custom_divisor !=
1271 info->custom_divisor)) {
1272 if (new_serial.custom_divisor == 0)
1273 return -EINVAL;
1274 baud = new_serial.baud_base / new_serial.custom_divisor;
1275 tty_encode_baud_rate(tty, baud, baud);
1276 }
1277 }
1278
1279 info->type = new_serial.type;
1280
1281 process_txrx_fifo(info);
1282
1283 if (tty_port_initialized(port)) {
1284 if (flags != (port->flags & ASYNC_SPD_MASK)) {
1285 spin_lock_irqsave(&info->slock, sl_flags);
1286 mxser_change_speed(tty);
1287 spin_unlock_irqrestore(&info->slock, sl_flags);
1288 }
1289 } else {
1290 retval = mxser_activate(port, tty);
1291 if (retval == 0)
1292 tty_port_set_initialized(port, 1);
1293 }
1294 return retval;
1295}
1296
1297/*
1298 * mxser_get_lsr_info - get line status register info
1299 *
1300 * Purpose: Let user call ioctl() to get info when the UART physically
1301 * is emptied. On bus types like RS485, the transmitter must
1302 * release the bus after transmitting. This must be done when
1303 * the transmit shift register is empty, not be done when the
1304 * transmit holding register is empty. This functionality
1305 * allows an RS485 driver to be written in user space.
1306 */
1307static int mxser_get_lsr_info(struct mxser_port *info,
1308 unsigned int __user *value)
1309{
1310 unsigned char status;
1311 unsigned int result;
1312 unsigned long flags;
1313
1314 spin_lock_irqsave(&info->slock, flags);
1315 status = inb(info->ioaddr + UART_LSR);
1316 spin_unlock_irqrestore(&info->slock, flags);
1317 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1318 return put_user(result, value);
1319}
1320
1321static int mxser_tiocmget(struct tty_struct *tty)
1322{
1323 struct mxser_port *info = tty->driver_data;
1324 unsigned char control, status;
1325 unsigned long flags;
1326
1327
1328 if (tty->index == MXSER_PORTS)
1329 return -ENOIOCTLCMD;
1330 if (tty_io_error(tty))
1331 return -EIO;
1332
1333 control = info->MCR;
1334
1335 spin_lock_irqsave(&info->slock, flags);
1336 status = inb(info->ioaddr + UART_MSR);
1337 if (status & UART_MSR_ANY_DELTA)
1338 mxser_check_modem_status(tty, info, status);
1339 spin_unlock_irqrestore(&info->slock, flags);
1340 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
1341 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
1342 ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
1343 ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
1344 ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
1345 ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
1346}
1347
1348static int mxser_tiocmset(struct tty_struct *tty,
1349 unsigned int set, unsigned int clear)
1350{
1351 struct mxser_port *info = tty->driver_data;
1352 unsigned long flags;
1353
1354
1355 if (tty->index == MXSER_PORTS)
1356 return -ENOIOCTLCMD;
1357 if (tty_io_error(tty))
1358 return -EIO;
1359
1360 spin_lock_irqsave(&info->slock, flags);
1361
1362 if (set & TIOCM_RTS)
1363 info->MCR |= UART_MCR_RTS;
1364 if (set & TIOCM_DTR)
1365 info->MCR |= UART_MCR_DTR;
1366
1367 if (clear & TIOCM_RTS)
1368 info->MCR &= ~UART_MCR_RTS;
1369 if (clear & TIOCM_DTR)
1370 info->MCR &= ~UART_MCR_DTR;
1371
1372 outb(info->MCR, info->ioaddr + UART_MCR);
1373 spin_unlock_irqrestore(&info->slock, flags);
1374 return 0;
1375}
1376
1377static int __init mxser_program_mode(int port)
1378{
1379 int id, i, j, n;
1380
1381 outb(0, port);
1382 outb(0, port);
1383 outb(0, port);
1384 (void)inb(port);
1385 (void)inb(port);
1386 outb(0, port);
1387 (void)inb(port);
1388
1389 id = inb(port + 1) & 0x1F;
1390 if ((id != C168_ASIC_ID) &&
1391 (id != C104_ASIC_ID) &&
1392 (id != C102_ASIC_ID) &&
1393 (id != CI132_ASIC_ID) &&
1394 (id != CI134_ASIC_ID) &&
1395 (id != CI104J_ASIC_ID))
1396 return -1;
1397 for (i = 0, j = 0; i < 4; i++) {
1398 n = inb(port + 2);
1399 if (n == 'M') {
1400 j = 1;
1401 } else if ((j == 1) && (n == 1)) {
1402 j = 2;
1403 break;
1404 } else
1405 j = 0;
1406 }
1407 if (j != 2)
1408 id = -2;
1409 return id;
1410}
1411
1412static void __init mxser_normal_mode(int port)
1413{
1414 int i, n;
1415
1416 outb(0xA5, port + 1);
1417 outb(0x80, port + 3);
1418 outb(12, port + 0); /* 9600 bps */
1419 outb(0, port + 1);
1420 outb(0x03, port + 3); /* 8 data bits */
1421 outb(0x13, port + 4); /* loop back mode */
1422 for (i = 0; i < 16; i++) {
1423 n = inb(port + 5);
1424 if ((n & 0x61) == 0x60)
1425 break;
1426 if ((n & 1) == 1)
1427 (void)inb(port);
1428 }
1429 outb(0x00, port + 4);
1430}
1431
1432#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */
1433#define CHIP_DO 0x02 /* Serial Data Output in Eprom */
1434#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */
1435#define CHIP_DI 0x08 /* Serial Data Input in Eprom */
1436#define EN_CCMD 0x000 /* Chip's command register */
1437#define EN0_RSARLO 0x008 /* Remote start address reg 0 */
1438#define EN0_RSARHI 0x009 /* Remote start address reg 1 */
1439#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */
1440#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */
1441#define EN0_DCFG 0x00E /* Data configuration reg WR */
1442#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */
1443#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */
1444#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */
1445static int __init mxser_read_register(int port, unsigned short *regs)
1446{
1447 int i, k, value, id;
1448 unsigned int j;
1449
1450 id = mxser_program_mode(port);
1451 if (id < 0)
1452 return id;
1453 for (i = 0; i < 14; i++) {
1454 k = (i & 0x3F) | 0x180;
1455 for (j = 0x100; j > 0; j >>= 1) {
1456 outb(CHIP_CS, port);
1457 if (k & j) {
1458 outb(CHIP_CS | CHIP_DO, port);
1459 outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */
1460 } else {
1461 outb(CHIP_CS, port);
1462 outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */
1463 }
1464 }
1465 (void)inb(port);
1466 value = 0;
1467 for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
1468 outb(CHIP_CS, port);
1469 outb(CHIP_CS | CHIP_SK, port);
1470 if (inb(port) & CHIP_DI)
1471 value |= j;
1472 }
1473 regs[i] = value;
1474 outb(0, port);
1475 }
1476 mxser_normal_mode(port);
1477 return id;
1478}
1479
1480static int mxser_ioctl_special(unsigned int cmd, void __user *argp)
1481{
1482 struct mxser_port *ip;
1483 struct tty_port *port;
1484 struct tty_struct *tty;
1485 int result, status;
1486 unsigned int i, j;
1487 int ret = 0;
1488
1489 switch (cmd) {
1490 case MOXA_GET_MAJOR:
1491 printk_ratelimited(KERN_WARNING "mxser: '%s' uses deprecated ioctl "
1492 "%x (GET_MAJOR), fix your userspace\n",
1493 current->comm, cmd);
1494 return put_user(ttymajor, (int __user *)argp);
1495
1496 case MOXA_CHKPORTENABLE:
1497 result = 0;
1498 for (i = 0; i < MXSER_BOARDS; i++)
1499 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++)
1500 if (mxser_boards[i].ports[j].ioaddr)
1501 result |= (1 << i);
1502 return put_user(result, (unsigned long __user *)argp);
1503 case MOXA_GETDATACOUNT:
1504 /* The receive side is locked by port->slock but it isn't
1505 clear that an exact snapshot is worth copying here */
1506 if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log)))
1507 ret = -EFAULT;
1508 return ret;
1509 case MOXA_GETMSTATUS: {
1510 struct mxser_mstatus ms, __user *msu = argp;
1511 for (i = 0; i < MXSER_BOARDS; i++)
1512 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) {
1513 ip = &mxser_boards[i].ports[j];
1514 port = &ip->port;
1515 memset(&ms, 0, sizeof(ms));
1516
1517 mutex_lock(&port->mutex);
1518 if (!ip->ioaddr)
1519 goto copy;
1520
1521 tty = tty_port_tty_get(port);
1522
1523 if (!tty)
1524 ms.cflag = ip->normal_termios.c_cflag;
1525 else
1526 ms.cflag = tty->termios.c_cflag;
1527 tty_kref_put(tty);
1528 spin_lock_irq(&ip->slock);
1529 status = inb(ip->ioaddr + UART_MSR);
1530 spin_unlock_irq(&ip->slock);
1531 if (status & UART_MSR_DCD)
1532 ms.dcd = 1;
1533 if (status & UART_MSR_DSR)
1534 ms.dsr = 1;
1535 if (status & UART_MSR_CTS)
1536 ms.cts = 1;
1537 copy:
1538 mutex_unlock(&port->mutex);
1539 if (copy_to_user(msu, &ms, sizeof(ms)))
1540 return -EFAULT;
1541 msu++;
1542 }
1543 return 0;
1544 }
1545 case MOXA_ASPP_MON_EXT: {
1546 struct mxser_mon_ext *me; /* it's 2k, stack unfriendly */
1547 unsigned int cflag, iflag, p;
1548 u8 opmode;
1549
1550 me = kzalloc(sizeof(*me), GFP_KERNEL);
1551 if (!me)
1552 return -ENOMEM;
1553
1554 for (i = 0, p = 0; i < MXSER_BOARDS; i++) {
1555 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++, p++) {
1556 if (p >= ARRAY_SIZE(me->rx_cnt)) {
1557 i = MXSER_BOARDS;
1558 break;
1559 }
1560 ip = &mxser_boards[i].ports[j];
1561 port = &ip->port;
1562
1563 mutex_lock(&port->mutex);
1564 if (!ip->ioaddr) {
1565 mutex_unlock(&port->mutex);
1566 continue;
1567 }
1568
1569 spin_lock_irq(&ip->slock);
1570 status = mxser_get_msr(ip->ioaddr, 0, p);
1571
1572 if (status & UART_MSR_TERI)
1573 ip->icount.rng++;
1574 if (status & UART_MSR_DDSR)
1575 ip->icount.dsr++;
1576 if (status & UART_MSR_DDCD)
1577 ip->icount.dcd++;
1578 if (status & UART_MSR_DCTS)
1579 ip->icount.cts++;
1580
1581 ip->mon_data.modem_status = status;
1582 me->rx_cnt[p] = ip->mon_data.rxcnt;
1583 me->tx_cnt[p] = ip->mon_data.txcnt;
1584 me->up_rxcnt[p] = ip->mon_data.up_rxcnt;
1585 me->up_txcnt[p] = ip->mon_data.up_txcnt;
1586 me->modem_status[p] =
1587 ip->mon_data.modem_status;
1588 spin_unlock_irq(&ip->slock);
1589
1590 tty = tty_port_tty_get(&ip->port);
1591
1592 if (!tty) {
1593 cflag = ip->normal_termios.c_cflag;
1594 iflag = ip->normal_termios.c_iflag;
1595 me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios);
1596 } else {
1597 cflag = tty->termios.c_cflag;
1598 iflag = tty->termios.c_iflag;
1599 me->baudrate[p] = tty_get_baud_rate(tty);
1600 }
1601 tty_kref_put(tty);
1602
1603 me->databits[p] = cflag & CSIZE;
1604 me->stopbits[p] = cflag & CSTOPB;
1605 me->parity[p] = cflag & (PARENB | PARODD |
1606 CMSPAR);
1607
1608 if (cflag & CRTSCTS)
1609 me->flowctrl[p] |= 0x03;
1610
1611 if (iflag & (IXON | IXOFF))
1612 me->flowctrl[p] |= 0x0C;
1613
1614 if (ip->type == PORT_16550A)
1615 me->fifo[p] = 1;
1616
1617 if (ip->board->chip_flag == MOXA_MUST_MU860_HWID) {
1618 opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
1619 opmode &= OP_MODE_MASK;
1620 } else {
1621 opmode = RS232_MODE;
1622 }
1623 me->iftype[p] = opmode;
1624 mutex_unlock(&port->mutex);
1625 }
1626 }
1627 if (copy_to_user(argp, me, sizeof(*me)))
1628 ret = -EFAULT;
1629 kfree(me);
1630 return ret;
1631 }
1632 default:
1633 return -ENOIOCTLCMD;
1634 }
1635 return 0;
1636}
1637
1638static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
1639 struct async_icount *cprev)
1640{
1641 struct async_icount cnow;
1642 unsigned long flags;
1643 int ret;
1644
1645 spin_lock_irqsave(&info->slock, flags);
1646 cnow = info->icount; /* atomic copy */
1647 spin_unlock_irqrestore(&info->slock, flags);
1648
1649 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
1650 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
1651 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
1652 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
1653
1654 *cprev = cnow;
1655
1656 return ret;
1657}
1658
1659static int mxser_ioctl(struct tty_struct *tty,
1660 unsigned int cmd, unsigned long arg)
1661{
1662 struct mxser_port *info = tty->driver_data;
1663 struct tty_port *port = &info->port;
1664 struct async_icount cnow;
1665 unsigned long flags;
1666 void __user *argp = (void __user *)arg;
1667 int retval;
1668
1669 if (tty->index == MXSER_PORTS)
1670 return mxser_ioctl_special(cmd, argp);
1671
1672 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) {
1673 int p;
1674 unsigned long opmode;
1675 static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f };
1676 int shiftbit;
1677 unsigned char val, mask;
1678
1679 if (info->board->chip_flag != MOXA_MUST_MU860_HWID)
1680 return -EFAULT;
1681
1682 p = tty->index % 4;
1683 if (cmd == MOXA_SET_OP_MODE) {
1684 if (get_user(opmode, (int __user *) argp))
1685 return -EFAULT;
1686 if (opmode != RS232_MODE &&
1687 opmode != RS485_2WIRE_MODE &&
1688 opmode != RS422_MODE &&
1689 opmode != RS485_4WIRE_MODE)
1690 return -EFAULT;
1691 mask = ModeMask[p];
1692 shiftbit = p * 2;
1693 spin_lock_irq(&info->slock);
1694 val = inb(info->opmode_ioaddr);
1695 val &= mask;
1696 val |= (opmode << shiftbit);
1697 outb(val, info->opmode_ioaddr);
1698 spin_unlock_irq(&info->slock);
1699 } else {
1700 shiftbit = p * 2;
1701 spin_lock_irq(&info->slock);
1702 opmode = inb(info->opmode_ioaddr) >> shiftbit;
1703 spin_unlock_irq(&info->slock);
1704 opmode &= OP_MODE_MASK;
1705 if (put_user(opmode, (int __user *)argp))
1706 return -EFAULT;
1707 }
1708 return 0;
1709 }
1710
1711 if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && tty_io_error(tty))
1712 return -EIO;
1713
1714 switch (cmd) {
1715 case TIOCGSERIAL:
1716 mutex_lock(&port->mutex);
1717 retval = mxser_get_serial_info(tty, argp);
1718 mutex_unlock(&port->mutex);
1719 return retval;
1720 case TIOCSSERIAL:
1721 mutex_lock(&port->mutex);
1722 retval = mxser_set_serial_info(tty, argp);
1723 mutex_unlock(&port->mutex);
1724 return retval;
1725 case TIOCSERGETLSR: /* Get line status register */
1726 return mxser_get_lsr_info(info, argp);
1727 /*
1728 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1729 * - mask passed in arg for lines of interest
1730 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1731 * Caller should use TIOCGICOUNT to see which one it was
1732 */
1733 case TIOCMIWAIT:
1734 spin_lock_irqsave(&info->slock, flags);
1735 cnow = info->icount; /* note the counters on entry */
1736 spin_unlock_irqrestore(&info->slock, flags);
1737
1738 return wait_event_interruptible(info->port.delta_msr_wait,
1739 mxser_cflags_changed(info, arg, &cnow));
1740 case MOXA_HighSpeedOn:
1741 return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp);
1742 case MOXA_SDS_RSTICOUNTER:
1743 spin_lock_irq(&info->slock);
1744 info->mon_data.rxcnt = 0;
1745 info->mon_data.txcnt = 0;
1746 spin_unlock_irq(&info->slock);
1747 return 0;
1748
1749 case MOXA_ASPP_OQUEUE:{
1750 int len, lsr;
1751
1752 len = mxser_chars_in_buffer(tty);
1753 spin_lock_irq(&info->slock);
1754 lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE;
1755 spin_unlock_irq(&info->slock);
1756 len += (lsr ? 0 : 1);
1757
1758 return put_user(len, (int __user *)argp);
1759 }
1760 case MOXA_ASPP_MON: {
1761 int mcr, status;
1762
1763 spin_lock_irq(&info->slock);
1764 status = mxser_get_msr(info->ioaddr, 1, tty->index);
1765 mxser_check_modem_status(tty, info, status);
1766
1767 mcr = inb(info->ioaddr + UART_MCR);
1768 spin_unlock_irq(&info->slock);
1769
1770 if (mcr & MOXA_MUST_MCR_XON_FLAG)
1771 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD;
1772 else
1773 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD;
1774
1775 if (mcr & MOXA_MUST_MCR_TX_XON)
1776 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT;
1777 else
1778 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
1779
1780 if (tty->hw_stopped)
1781 info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
1782 else
1783 info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
1784
1785 if (copy_to_user(argp, &info->mon_data,
1786 sizeof(struct mxser_mon)))
1787 return -EFAULT;
1788
1789 return 0;
1790 }
1791 case MOXA_ASPP_LSTATUS: {
1792 if (put_user(info->err_shadow, (unsigned char __user *)argp))
1793 return -EFAULT;
1794
1795 info->err_shadow = 0;
1796 return 0;
1797 }
1798 case MOXA_SET_BAUD_METHOD: {
1799 int method;
1800
1801 if (get_user(method, (int __user *)argp))
1802 return -EFAULT;
1803 mxser_set_baud_method[tty->index] = method;
1804 return put_user(method, (int __user *)argp);
1805 }
1806 default:
1807 return -ENOIOCTLCMD;
1808 }
1809 return 0;
1810}
1811
1812 /*
1813 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1814 * Return: write counters to the user passed counter struct
1815 * NB: both 1->0 and 0->1 transitions are counted except for
1816 * RI where only 0->1 is counted.
1817 */
1818
1819static int mxser_get_icount(struct tty_struct *tty,
1820 struct serial_icounter_struct *icount)
1821
1822{
1823 struct mxser_port *info = tty->driver_data;
1824 struct async_icount cnow;
1825 unsigned long flags;
1826
1827 spin_lock_irqsave(&info->slock, flags);
1828 cnow = info->icount;
1829 spin_unlock_irqrestore(&info->slock, flags);
1830
1831 icount->frame = cnow.frame;
1832 icount->brk = cnow.brk;
1833 icount->overrun = cnow.overrun;
1834 icount->buf_overrun = cnow.buf_overrun;
1835 icount->parity = cnow.parity;
1836 icount->rx = cnow.rx;
1837 icount->tx = cnow.tx;
1838 icount->cts = cnow.cts;
1839 icount->dsr = cnow.dsr;
1840 icount->rng = cnow.rng;
1841 icount->dcd = cnow.dcd;
1842 return 0;
1843}
1844
1845static void mxser_stoprx(struct tty_struct *tty)
1846{
1847 struct mxser_port *info = tty->driver_data;
1848
1849 info->ldisc_stop_rx = 1;
1850 if (I_IXOFF(tty)) {
1851 if (info->board->chip_flag) {
1852 info->IER &= ~MOXA_MUST_RECV_ISR;
1853 outb(info->IER, info->ioaddr + UART_IER);
1854 } else {
1855 info->x_char = STOP_CHAR(tty);
1856 outb(0, info->ioaddr + UART_IER);
1857 info->IER |= UART_IER_THRI;
1858 outb(info->IER, info->ioaddr + UART_IER);
1859 }
1860 }
1861
1862 if (C_CRTSCTS(tty)) {
1863 info->MCR &= ~UART_MCR_RTS;
1864 outb(info->MCR, info->ioaddr + UART_MCR);
1865 }
1866}
1867
1868/*
1869 * This routine is called by the upper-layer tty layer to signal that
1870 * incoming characters should be throttled.
1871 */
1872static void mxser_throttle(struct tty_struct *tty)
1873{
1874 mxser_stoprx(tty);
1875}
1876
1877static void mxser_unthrottle(struct tty_struct *tty)
1878{
1879 struct mxser_port *info = tty->driver_data;
1880
1881 /* startrx */
1882 info->ldisc_stop_rx = 0;
1883 if (I_IXOFF(tty)) {
1884 if (info->x_char)
1885 info->x_char = 0;
1886 else {
1887 if (info->board->chip_flag) {
1888 info->IER |= MOXA_MUST_RECV_ISR;
1889 outb(info->IER, info->ioaddr + UART_IER);
1890 } else {
1891 info->x_char = START_CHAR(tty);
1892 outb(0, info->ioaddr + UART_IER);
1893 info->IER |= UART_IER_THRI;
1894 outb(info->IER, info->ioaddr + UART_IER);
1895 }
1896 }
1897 }
1898
1899 if (C_CRTSCTS(tty)) {
1900 info->MCR |= UART_MCR_RTS;
1901 outb(info->MCR, info->ioaddr + UART_MCR);
1902 }
1903}
1904
1905/*
1906 * mxser_stop() and mxser_start()
1907 *
1908 * This routines are called before setting or resetting tty->stopped.
1909 * They enable or disable transmitter interrupts, as necessary.
1910 */
1911static void mxser_stop(struct tty_struct *tty)
1912{
1913 struct mxser_port *info = tty->driver_data;
1914 unsigned long flags;
1915
1916 spin_lock_irqsave(&info->slock, flags);
1917 if (info->IER & UART_IER_THRI) {
1918 info->IER &= ~UART_IER_THRI;
1919 outb(info->IER, info->ioaddr + UART_IER);
1920 }
1921 spin_unlock_irqrestore(&info->slock, flags);
1922}
1923
1924static void mxser_start(struct tty_struct *tty)
1925{
1926 struct mxser_port *info = tty->driver_data;
1927 unsigned long flags;
1928
1929 spin_lock_irqsave(&info->slock, flags);
1930 if (info->xmit_cnt && info->port.xmit_buf) {
1931 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1932 info->IER |= UART_IER_THRI;
1933 outb(info->IER, info->ioaddr + UART_IER);
1934 }
1935 spin_unlock_irqrestore(&info->slock, flags);
1936}
1937
1938static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
1939{
1940 struct mxser_port *info = tty->driver_data;
1941 unsigned long flags;
1942
1943 spin_lock_irqsave(&info->slock, flags);
1944 mxser_change_speed(tty);
1945 spin_unlock_irqrestore(&info->slock, flags);
1946
1947 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
1948 tty->hw_stopped = 0;
1949 mxser_start(tty);
1950 }
1951
1952 /* Handle sw stopped */
1953 if ((old_termios->c_iflag & IXON) && !I_IXON(tty)) {
1954 tty->stopped = 0;
1955
1956 if (info->board->chip_flag) {
1957 spin_lock_irqsave(&info->slock, flags);
1958 mxser_disable_must_rx_software_flow_control(
1959 info->ioaddr);
1960 spin_unlock_irqrestore(&info->slock, flags);
1961 }
1962
1963 mxser_start(tty);
1964 }
1965}
1966
1967/*
1968 * mxser_wait_until_sent() --- wait until the transmitter is empty
1969 */
1970static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
1971{
1972 struct mxser_port *info = tty->driver_data;
1973 unsigned long orig_jiffies, char_time;
1974 unsigned long flags;
1975 int lsr;
1976
1977 if (info->type == PORT_UNKNOWN)
1978 return;
1979
1980 if (info->xmit_fifo_size == 0)
1981 return; /* Just in case.... */
1982
1983 orig_jiffies = jiffies;
1984 /*
1985 * Set the check interval to be 1/5 of the estimated time to
1986 * send a single character, and make it at least 1. The check
1987 * interval should also be less than the timeout.
1988 *
1989 * Note: we have to use pretty tight timings here to satisfy
1990 * the NIST-PCTS.
1991 */
1992 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
1993 char_time = char_time / 5;
1994 if (char_time == 0)
1995 char_time = 1;
1996 if (timeout && timeout < char_time)
1997 char_time = timeout;
1998 /*
1999 * If the transmitter hasn't cleared in twice the approximate
2000 * amount of time to send the entire FIFO, it probably won't
2001 * ever clear. This assumes the UART isn't doing flow
2002 * control, which is currently the case. Hence, if it ever
2003 * takes longer than info->timeout, this is probably due to a
2004 * UART bug of some kind. So, we clamp the timeout parameter at
2005 * 2*info->timeout.
2006 */
2007 if (!timeout || timeout > 2 * info->timeout)
2008 timeout = 2 * info->timeout;
2009
2010 spin_lock_irqsave(&info->slock, flags);
2011 while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) {
2012 spin_unlock_irqrestore(&info->slock, flags);
2013 schedule_timeout_interruptible(char_time);
2014 spin_lock_irqsave(&info->slock, flags);
2015 if (signal_pending(current))
2016 break;
2017 if (timeout && time_after(jiffies, orig_jiffies + timeout))
2018 break;
2019 }
2020 spin_unlock_irqrestore(&info->slock, flags);
2021 set_current_state(TASK_RUNNING);
2022}
2023
2024/*
2025 * This routine is called by tty_hangup() when a hangup is signaled.
2026 */
2027static void mxser_hangup(struct tty_struct *tty)
2028{
2029 struct mxser_port *info = tty->driver_data;
2030
2031 mxser_flush_buffer(tty);
2032 tty_port_hangup(&info->port);
2033}
2034
2035/*
2036 * mxser_rs_break() --- routine which turns the break handling on or off
2037 */
2038static int mxser_rs_break(struct tty_struct *tty, int break_state)
2039{
2040 struct mxser_port *info = tty->driver_data;
2041 unsigned long flags;
2042
2043 spin_lock_irqsave(&info->slock, flags);
2044 if (break_state == -1)
2045 outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC,
2046 info->ioaddr + UART_LCR);
2047 else
2048 outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
2049 info->ioaddr + UART_LCR);
2050 spin_unlock_irqrestore(&info->slock, flags);
2051 return 0;
2052}
2053
2054static void mxser_receive_chars(struct tty_struct *tty,
2055 struct mxser_port *port, int *status)
2056{
2057 unsigned char ch, gdl;
2058 int ignored = 0;
2059 int cnt = 0;
2060 int recv_room;
2061 int max = 256;
2062
2063 recv_room = tty->receive_room;
2064 if (recv_room == 0 && !port->ldisc_stop_rx)
2065 mxser_stoprx(tty);
2066 if (port->board->chip_flag != MOXA_OTHER_UART) {
2067
2068 if (*status & UART_LSR_SPECIAL)
2069 goto intr_old;
2070 if (port->board->chip_flag == MOXA_MUST_MU860_HWID &&
2071 (*status & MOXA_MUST_LSR_RERR))
2072 goto intr_old;
2073 if (*status & MOXA_MUST_LSR_RERR)
2074 goto intr_old;
2075
2076 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
2077
2078 if (port->board->chip_flag == MOXA_MUST_MU150_HWID)
2079 gdl &= MOXA_MUST_GDL_MASK;
2080 if (gdl >= recv_room) {
2081 if (!port->ldisc_stop_rx)
2082 mxser_stoprx(tty);
2083 }
2084 while (gdl--) {
2085 ch = inb(port->ioaddr + UART_RX);
2086 tty_insert_flip_char(&port->port, ch, 0);
2087 cnt++;
2088 }
2089 goto end_intr;
2090 }
2091intr_old:
2092
2093 do {
2094 if (max-- < 0)
2095 break;
2096
2097 ch = inb(port->ioaddr + UART_RX);
2098 if (port->board->chip_flag && (*status & UART_LSR_OE))
2099 outb(0x23, port->ioaddr + UART_FCR);
2100 *status &= port->read_status_mask;
2101 if (*status & port->ignore_status_mask) {
2102 if (++ignored > 100)
2103 break;
2104 } else {
2105 char flag = 0;
2106 if (*status & UART_LSR_SPECIAL) {
2107 if (*status & UART_LSR_BI) {
2108 flag = TTY_BREAK;
2109 port->icount.brk++;
2110
2111 if (port->port.flags & ASYNC_SAK)
2112 do_SAK(tty);
2113 } else if (*status & UART_LSR_PE) {
2114 flag = TTY_PARITY;
2115 port->icount.parity++;
2116 } else if (*status & UART_LSR_FE) {
2117 flag = TTY_FRAME;
2118 port->icount.frame++;
2119 } else if (*status & UART_LSR_OE) {
2120 flag = TTY_OVERRUN;
2121 port->icount.overrun++;
2122 } else
2123 flag = TTY_BREAK;
2124 }
2125 tty_insert_flip_char(&port->port, ch, flag);
2126 cnt++;
2127 if (cnt >= recv_room) {
2128 if (!port->ldisc_stop_rx)
2129 mxser_stoprx(tty);
2130 break;
2131 }
2132
2133 }
2134
2135 if (port->board->chip_flag)
2136 break;
2137
2138 *status = inb(port->ioaddr + UART_LSR);
2139 } while (*status & UART_LSR_DR);
2140
2141end_intr:
2142 mxvar_log.rxcnt[tty->index] += cnt;
2143 port->mon_data.rxcnt += cnt;
2144 port->mon_data.up_rxcnt += cnt;
2145
2146 /*
2147 * We are called from an interrupt context with &port->slock
2148 * being held. Drop it temporarily in order to prevent
2149 * recursive locking.
2150 */
2151 spin_unlock(&port->slock);
2152 tty_flip_buffer_push(&port->port);
2153 spin_lock(&port->slock);
2154}
2155
2156static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
2157{
2158 int count, cnt;
2159
2160 if (port->x_char) {
2161 outb(port->x_char, port->ioaddr + UART_TX);
2162 port->x_char = 0;
2163 mxvar_log.txcnt[tty->index]++;
2164 port->mon_data.txcnt++;
2165 port->mon_data.up_txcnt++;
2166 port->icount.tx++;
2167 return;
2168 }
2169
2170 if (port->port.xmit_buf == NULL)
2171 return;
2172
2173 if (port->xmit_cnt <= 0 || tty->stopped ||
2174 (tty->hw_stopped &&
2175 (port->type != PORT_16550A) &&
2176 (!port->board->chip_flag))) {
2177 port->IER &= ~UART_IER_THRI;
2178 outb(port->IER, port->ioaddr + UART_IER);
2179 return;
2180 }
2181
2182 cnt = port->xmit_cnt;
2183 count = port->xmit_fifo_size;
2184 do {
2185 outb(port->port.xmit_buf[port->xmit_tail++],
2186 port->ioaddr + UART_TX);
2187 port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1);
2188 if (--port->xmit_cnt <= 0)
2189 break;
2190 } while (--count > 0);
2191 mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt);
2192
2193 port->mon_data.txcnt += (cnt - port->xmit_cnt);
2194 port->mon_data.up_txcnt += (cnt - port->xmit_cnt);
2195 port->icount.tx += (cnt - port->xmit_cnt);
2196
2197 if (port->xmit_cnt < WAKEUP_CHARS)
2198 tty_wakeup(tty);
2199
2200 if (port->xmit_cnt <= 0) {
2201 port->IER &= ~UART_IER_THRI;
2202 outb(port->IER, port->ioaddr + UART_IER);
2203 }
2204}
2205
2206/*
2207 * This is the serial driver's generic interrupt routine
2208 */
2209static irqreturn_t mxser_interrupt(int irq, void *dev_id)
2210{
2211 int status, iir, i;
2212 struct mxser_board *brd = NULL;
2213 struct mxser_port *port;
2214 int max, irqbits, bits, msr;
2215 unsigned int int_cnt, pass_counter = 0;
2216 int handled = IRQ_NONE;
2217 struct tty_struct *tty;
2218
2219 for (i = 0; i < MXSER_BOARDS; i++)
2220 if (dev_id == &mxser_boards[i]) {
2221 brd = dev_id;
2222 break;
2223 }
2224
2225 if (i == MXSER_BOARDS)
2226 goto irq_stop;
2227 if (brd == NULL)
2228 goto irq_stop;
2229 max = brd->info->nports;
2230 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
2231 irqbits = inb(brd->vector) & brd->vector_mask;
2232 if (irqbits == brd->vector_mask)
2233 break;
2234
2235 handled = IRQ_HANDLED;
2236 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
2237 if (irqbits == brd->vector_mask)
2238 break;
2239 if (bits & irqbits)
2240 continue;
2241 port = &brd->ports[i];
2242
2243 int_cnt = 0;
2244 spin_lock(&port->slock);
2245 do {
2246 iir = inb(port->ioaddr + UART_IIR);
2247 if (iir & UART_IIR_NO_INT)
2248 break;
2249 iir &= MOXA_MUST_IIR_MASK;
2250 tty = tty_port_tty_get(&port->port);
2251 if (!tty || port->closing ||
2252 !tty_port_initialized(&port->port)) {
2253 status = inb(port->ioaddr + UART_LSR);
2254 outb(0x27, port->ioaddr + UART_FCR);
2255 inb(port->ioaddr + UART_MSR);
2256 tty_kref_put(tty);
2257 break;
2258 }
2259
2260 status = inb(port->ioaddr + UART_LSR);
2261
2262 if (status & UART_LSR_PE)
2263 port->err_shadow |= NPPI_NOTIFY_PARITY;
2264 if (status & UART_LSR_FE)
2265 port->err_shadow |= NPPI_NOTIFY_FRAMING;
2266 if (status & UART_LSR_OE)
2267 port->err_shadow |=
2268 NPPI_NOTIFY_HW_OVERRUN;
2269 if (status & UART_LSR_BI)
2270 port->err_shadow |= NPPI_NOTIFY_BREAK;
2271
2272 if (port->board->chip_flag) {
2273 if (iir == MOXA_MUST_IIR_GDA ||
2274 iir == MOXA_MUST_IIR_RDA ||
2275 iir == MOXA_MUST_IIR_RTO ||
2276 iir == MOXA_MUST_IIR_LSR)
2277 mxser_receive_chars(tty, port,
2278 &status);
2279
2280 } else {
2281 status &= port->read_status_mask;
2282 if (status & UART_LSR_DR)
2283 mxser_receive_chars(tty, port,
2284 &status);
2285 }
2286 msr = inb(port->ioaddr + UART_MSR);
2287 if (msr & UART_MSR_ANY_DELTA)
2288 mxser_check_modem_status(tty, port, msr);
2289
2290 if (port->board->chip_flag) {
2291 if (iir == 0x02 && (status &
2292 UART_LSR_THRE))
2293 mxser_transmit_chars(tty, port);
2294 } else {
2295 if (status & UART_LSR_THRE)
2296 mxser_transmit_chars(tty, port);
2297 }
2298 tty_kref_put(tty);
2299 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
2300 spin_unlock(&port->slock);
2301 }
2302 }
2303
2304irq_stop:
2305 return handled;
2306}
2307
2308static const struct tty_operations mxser_ops = {
2309 .open = mxser_open,
2310 .close = mxser_close,
2311 .write = mxser_write,
2312 .put_char = mxser_put_char,
2313 .flush_chars = mxser_flush_chars,
2314 .write_room = mxser_write_room,
2315 .chars_in_buffer = mxser_chars_in_buffer,
2316 .flush_buffer = mxser_flush_buffer,
2317 .ioctl = mxser_ioctl,
2318 .throttle = mxser_throttle,
2319 .unthrottle = mxser_unthrottle,
2320 .set_termios = mxser_set_termios,
2321 .stop = mxser_stop,
2322 .start = mxser_start,
2323 .hangup = mxser_hangup,
2324 .break_ctl = mxser_rs_break,
2325 .wait_until_sent = mxser_wait_until_sent,
2326 .tiocmget = mxser_tiocmget,
2327 .tiocmset = mxser_tiocmset,
2328 .get_icount = mxser_get_icount,
2329};
2330
2331static const struct tty_port_operations mxser_port_ops = {
2332 .carrier_raised = mxser_carrier_raised,
2333 .dtr_rts = mxser_dtr_rts,
2334 .activate = mxser_activate,
2335 .shutdown = mxser_shutdown_port,
2336};
2337
2338/*
2339 * The MOXA Smartio/Industio serial driver boot-time initialization code!
2340 */
2341
2342static bool allow_overlapping_vector;
2343module_param(allow_overlapping_vector, bool, S_IRUGO);
2344MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)");
2345
2346static bool mxser_overlapping_vector(struct mxser_board *brd)
2347{
2348 return allow_overlapping_vector &&
2349 brd->vector >= brd->ports[0].ioaddr &&
2350 brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports;
2351}
2352
2353static int mxser_request_vector(struct mxser_board *brd)
2354{
2355 if (mxser_overlapping_vector(brd))
2356 return 0;
2357 return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO;
2358}
2359
2360static void mxser_release_vector(struct mxser_board *brd)
2361{
2362 if (mxser_overlapping_vector(brd))
2363 return;
2364 release_region(brd->vector, 1);
2365}
2366
2367static void mxser_release_ISA_res(struct mxser_board *brd)
2368{
2369 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2370 mxser_release_vector(brd);
2371}
2372
2373static int mxser_initbrd(struct mxser_board *brd)
2374{
2375 struct mxser_port *info;
2376 unsigned int i;
2377 int retval;
2378
2379 printk(KERN_INFO "mxser: max. baud rate = %d bps\n",
2380 brd->ports[0].max_baud);
2381
2382 for (i = 0; i < brd->info->nports; i++) {
2383 info = &brd->ports[i];
2384 tty_port_init(&info->port);
2385 info->port.ops = &mxser_port_ops;
2386 info->board = brd;
2387 info->stop_rx = 0;
2388 info->ldisc_stop_rx = 0;
2389
2390 /* Enhance mode enabled here */
2391 if (brd->chip_flag != MOXA_OTHER_UART)
2392 mxser_enable_must_enchance_mode(info->ioaddr);
2393
2394 info->type = brd->uart_type;
2395
2396 process_txrx_fifo(info);
2397
2398 info->custom_divisor = info->baud_base * 16;
2399 info->port.close_delay = 5 * HZ / 10;
2400 info->port.closing_wait = 30 * HZ;
2401 info->normal_termios = mxvar_sdriver->init_termios;
2402 memset(&info->mon_data, 0, sizeof(struct mxser_mon));
2403 info->err_shadow = 0;
2404 spin_lock_init(&info->slock);
2405
2406 /* before set INT ISR, disable all int */
2407 outb(inb(info->ioaddr + UART_IER) & 0xf0,
2408 info->ioaddr + UART_IER);
2409 }
2410
2411 retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser",
2412 brd);
2413 if (retval) {
2414 for (i = 0; i < brd->info->nports; i++)
2415 tty_port_destroy(&brd->ports[i].port);
2416 printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may "
2417 "conflict with another device.\n",
2418 brd->info->name, brd->irq);
2419 }
2420
2421 return retval;
2422}
2423
2424static void mxser_board_remove(struct mxser_board *brd)
2425{
2426 unsigned int i;
2427
2428 for (i = 0; i < brd->info->nports; i++) {
2429 tty_unregister_device(mxvar_sdriver, brd->idx + i);
2430 tty_port_destroy(&brd->ports[i].port);
2431 }
2432 free_irq(brd->irq, brd);
2433}
2434
2435static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
2436{
2437 int id, i, bits, ret;
2438 unsigned short regs[16], irq;
2439 unsigned char scratch, scratch2;
2440
2441 brd->chip_flag = MOXA_OTHER_UART;
2442
2443 id = mxser_read_register(cap, regs);
2444 switch (id) {
2445 case C168_ASIC_ID:
2446 brd->info = &mxser_cards[0];
2447 break;
2448 case C104_ASIC_ID:
2449 brd->info = &mxser_cards[1];
2450 break;
2451 case CI104J_ASIC_ID:
2452 brd->info = &mxser_cards[2];
2453 break;
2454 case C102_ASIC_ID:
2455 brd->info = &mxser_cards[5];
2456 break;
2457 case CI132_ASIC_ID:
2458 brd->info = &mxser_cards[6];
2459 break;
2460 case CI134_ASIC_ID:
2461 brd->info = &mxser_cards[7];
2462 break;
2463 default:
2464 return 0;
2465 }
2466
2467 irq = 0;
2468 /* some ISA cards have 2 ports, but we want to see them as 4-port (why?)
2469 Flag-hack checks if configuration should be read as 2-port here. */
2470 if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) {
2471 irq = regs[9] & 0xF000;
2472 irq = irq | (irq >> 4);
2473 if (irq != (regs[9] & 0xFF00))
2474 goto err_irqconflict;
2475 } else if (brd->info->nports == 4) {
2476 irq = regs[9] & 0xF000;
2477 irq = irq | (irq >> 4);
2478 irq = irq | (irq >> 8);
2479 if (irq != regs[9])
2480 goto err_irqconflict;
2481 } else if (brd->info->nports == 8) {
2482 irq = regs[9] & 0xF000;
2483 irq = irq | (irq >> 4);
2484 irq = irq | (irq >> 8);
2485 if ((irq != regs[9]) || (irq != regs[10]))
2486 goto err_irqconflict;
2487 }
2488
2489 if (!irq) {
2490 printk(KERN_ERR "mxser: interrupt number unset\n");
2491 return -EIO;
2492 }
2493 brd->irq = ((int)(irq & 0xF000) >> 12);
2494 for (i = 0; i < 8; i++)
2495 brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8;
2496 if ((regs[12] & 0x80) == 0) {
2497 printk(KERN_ERR "mxser: invalid interrupt vector\n");
2498 return -EIO;
2499 }
2500 brd->vector = (int)regs[11]; /* interrupt vector */
2501 if (id == 1)
2502 brd->vector_mask = 0x00FF;
2503 else
2504 brd->vector_mask = 0x000F;
2505 for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) {
2506 if (regs[12] & bits) {
2507 brd->ports[i].baud_base = 921600;
2508 brd->ports[i].max_baud = 921600;
2509 } else {
2510 brd->ports[i].baud_base = 115200;
2511 brd->ports[i].max_baud = 115200;
2512 }
2513 }
2514 scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB);
2515 outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR);
2516 outb(0, cap + UART_EFR); /* EFR is the same as FCR */
2517 outb(scratch2, cap + UART_LCR);
2518 outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR);
2519 scratch = inb(cap + UART_IIR);
2520
2521 if (scratch & 0xC0)
2522 brd->uart_type = PORT_16550A;
2523 else
2524 brd->uart_type = PORT_16450;
2525 if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports,
2526 "mxser(IO)")) {
2527 printk(KERN_ERR "mxser: can't request ports I/O region: "
2528 "0x%.8lx-0x%.8lx\n",
2529 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2530 8 * brd->info->nports - 1);
2531 return -EIO;
2532 }
2533
2534 ret = mxser_request_vector(brd);
2535 if (ret) {
2536 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2537 printk(KERN_ERR "mxser: can't request interrupt vector region: "
2538 "0x%.8lx-0x%.8lx\n",
2539 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2540 8 * brd->info->nports - 1);
2541 return ret;
2542 }
2543 return brd->info->nports;
2544
2545err_irqconflict:
2546 printk(KERN_ERR "mxser: invalid interrupt number\n");
2547 return -EIO;
2548}
2549
2550static int mxser_probe(struct pci_dev *pdev,
2551 const struct pci_device_id *ent)
2552{
2553#ifdef CONFIG_PCI
2554 struct mxser_board *brd;
2555 unsigned int i, j;
2556 unsigned long ioaddress;
2557 struct device *tty_dev;
2558 int retval = -EINVAL;
2559
2560 for (i = 0; i < MXSER_BOARDS; i++)
2561 if (mxser_boards[i].info == NULL)
2562 break;
2563
2564 if (i >= MXSER_BOARDS) {
2565 dev_err(&pdev->dev, "too many boards found (maximum %d), board "
2566 "not configured\n", MXSER_BOARDS);
2567 goto err;
2568 }
2569
2570 brd = &mxser_boards[i];
2571 brd->idx = i * MXSER_PORTS_PER_BOARD;
2572 dev_info(&pdev->dev, "found MOXA %s board (BusNo=%d, DevNo=%d)\n",
2573 mxser_cards[ent->driver_data].name,
2574 pdev->bus->number, PCI_SLOT(pdev->devfn));
2575
2576 retval = pci_enable_device(pdev);
2577 if (retval) {
2578 dev_err(&pdev->dev, "PCI enable failed\n");
2579 goto err;
2580 }
2581
2582 /* io address */
2583 ioaddress = pci_resource_start(pdev, 2);
2584 retval = pci_request_region(pdev, 2, "mxser(IO)");
2585 if (retval)
2586 goto err_dis;
2587
2588 brd->info = &mxser_cards[ent->driver_data];
2589 for (i = 0; i < brd->info->nports; i++)
2590 brd->ports[i].ioaddr = ioaddress + 8 * i;
2591
2592 /* vector */
2593 ioaddress = pci_resource_start(pdev, 3);
2594 retval = pci_request_region(pdev, 3, "mxser(vector)");
2595 if (retval)
2596 goto err_zero;
2597 brd->vector = ioaddress;
2598
2599 /* irq */
2600 brd->irq = pdev->irq;
2601
2602 brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr);
2603 brd->uart_type = PORT_16550A;
2604 brd->vector_mask = 0;
2605
2606 for (i = 0; i < brd->info->nports; i++) {
2607 for (j = 0; j < UART_INFO_NUM; j++) {
2608 if (Gpci_uart_info[j].type == brd->chip_flag) {
2609 brd->ports[i].max_baud =
2610 Gpci_uart_info[j].max_baud;
2611
2612 /* exception....CP-102 */
2613 if (brd->info->flags & MXSER_HIGHBAUD)
2614 brd->ports[i].max_baud = 921600;
2615 break;
2616 }
2617 }
2618 }
2619
2620 if (brd->chip_flag == MOXA_MUST_MU860_HWID) {
2621 for (i = 0; i < brd->info->nports; i++) {
2622 if (i < 4)
2623 brd->ports[i].opmode_ioaddr = ioaddress + 4;
2624 else
2625 brd->ports[i].opmode_ioaddr = ioaddress + 0x0c;
2626 }
2627 outb(0, ioaddress + 4); /* default set to RS232 mode */
2628 outb(0, ioaddress + 0x0c); /* default set to RS232 mode */
2629 }
2630
2631 for (i = 0; i < brd->info->nports; i++) {
2632 brd->vector_mask |= (1 << i);
2633 brd->ports[i].baud_base = 921600;
2634 }
2635
2636 /* mxser_initbrd will hook ISR. */
2637 retval = mxser_initbrd(brd);
2638 if (retval)
2639 goto err_rel3;
2640
2641 for (i = 0; i < brd->info->nports; i++) {
2642 tty_dev = tty_port_register_device(&brd->ports[i].port,
2643 mxvar_sdriver, brd->idx + i, &pdev->dev);
2644 if (IS_ERR(tty_dev)) {
2645 retval = PTR_ERR(tty_dev);
2646 for (; i > 0; i--)
2647 tty_unregister_device(mxvar_sdriver,
2648 brd->idx + i - 1);
2649 goto err_relbrd;
2650 }
2651 }
2652
2653 pci_set_drvdata(pdev, brd);
2654
2655 return 0;
2656err_relbrd:
2657 for (i = 0; i < brd->info->nports; i++)
2658 tty_port_destroy(&brd->ports[i].port);
2659 free_irq(brd->irq, brd);
2660err_rel3:
2661 pci_release_region(pdev, 3);
2662err_zero:
2663 brd->info = NULL;
2664 pci_release_region(pdev, 2);
2665err_dis:
2666 pci_disable_device(pdev);
2667err:
2668 return retval;
2669#else
2670 return -ENODEV;
2671#endif
2672}
2673
2674static void mxser_remove(struct pci_dev *pdev)
2675{
2676#ifdef CONFIG_PCI
2677 struct mxser_board *brd = pci_get_drvdata(pdev);
2678
2679 mxser_board_remove(brd);
2680
2681 pci_release_region(pdev, 2);
2682 pci_release_region(pdev, 3);
2683 pci_disable_device(pdev);
2684 brd->info = NULL;
2685#endif
2686}
2687
2688static struct pci_driver mxser_driver = {
2689 .name = "mxser",
2690 .id_table = mxser_pcibrds,
2691 .probe = mxser_probe,
2692 .remove = mxser_remove
2693};
2694
2695static int __init mxser_module_init(void)
2696{
2697 struct mxser_board *brd;
2698 struct device *tty_dev;
2699 unsigned int b, i, m;
2700 int retval;
2701
2702 mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
2703 if (!mxvar_sdriver)
2704 return -ENOMEM;
2705
2706 printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n",
2707 MXSER_VERSION);
2708
2709 /* Initialize the tty_driver structure */
2710 mxvar_sdriver->name = "ttyMI";
2711 mxvar_sdriver->major = ttymajor;
2712 mxvar_sdriver->minor_start = 0;
2713 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
2714 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
2715 mxvar_sdriver->init_termios = tty_std_termios;
2716 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
2717 mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV;
2718 tty_set_operations(mxvar_sdriver, &mxser_ops);
2719
2720 retval = tty_register_driver(mxvar_sdriver);
2721 if (retval) {
2722 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
2723 "tty driver !\n");
2724 goto err_put;
2725 }
2726
2727 /* Start finding ISA boards here */
2728 for (m = 0, b = 0; b < MXSER_BOARDS; b++) {
2729 if (!ioaddr[b])
2730 continue;
2731
2732 brd = &mxser_boards[m];
2733 retval = mxser_get_ISA_conf(ioaddr[b], brd);
2734 if (retval <= 0) {
2735 brd->info = NULL;
2736 continue;
2737 }
2738
2739 printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n",
2740 brd->info->name, ioaddr[b]);
2741
2742 /* mxser_initbrd will hook ISR. */
2743 if (mxser_initbrd(brd) < 0) {
2744 mxser_release_ISA_res(brd);
2745 brd->info = NULL;
2746 continue;
2747 }
2748
2749 brd->idx = m * MXSER_PORTS_PER_BOARD;
2750 for (i = 0; i < brd->info->nports; i++) {
2751 tty_dev = tty_port_register_device(&brd->ports[i].port,
2752 mxvar_sdriver, brd->idx + i, NULL);
2753 if (IS_ERR(tty_dev)) {
2754 for (; i > 0; i--)
2755 tty_unregister_device(mxvar_sdriver,
2756 brd->idx + i - 1);
2757 for (i = 0; i < brd->info->nports; i++)
2758 tty_port_destroy(&brd->ports[i].port);
2759 free_irq(brd->irq, brd);
2760 mxser_release_ISA_res(brd);
2761 brd->info = NULL;
2762 break;
2763 }
2764 }
2765 if (brd->info == NULL)
2766 continue;
2767
2768 m++;
2769 }
2770
2771 retval = pci_register_driver(&mxser_driver);
2772 if (retval) {
2773 printk(KERN_ERR "mxser: can't register pci driver\n");
2774 if (!m) {
2775 retval = -ENODEV;
2776 goto err_unr;
2777 } /* else: we have some ISA cards under control */
2778 }
2779
2780 return 0;
2781err_unr:
2782 tty_unregister_driver(mxvar_sdriver);
2783err_put:
2784 put_tty_driver(mxvar_sdriver);
2785 return retval;
2786}
2787
2788static void __exit mxser_module_exit(void)
2789{
2790 unsigned int i;
2791
2792 pci_unregister_driver(&mxser_driver);
2793
2794 for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */
2795 if (mxser_boards[i].info != NULL)
2796 mxser_board_remove(&mxser_boards[i]);
2797 tty_unregister_driver(mxvar_sdriver);
2798 put_tty_driver(mxvar_sdriver);
2799
2800 for (i = 0; i < MXSER_BOARDS; i++)
2801 if (mxser_boards[i].info != NULL)
2802 mxser_release_ISA_res(&mxser_boards[i]);
2803}
2804
2805module_init(mxser_module_init);
2806module_exit(mxser_module_exit);