Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Derived from many drivers using generic_serial interface,
4 * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
5 * (was in Linux/VR tree) by Jim Pick.
6 *
7 * Copyright (C) 1999 Harald Koerfgen
8 * Copyright (C) 2000 Jim Pick <jim@jimpick.com>
9 * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
10 * Copyright (C) 2000-2002 Toshiba Corporation
11 *
12 * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
13 */
14
15#include <linux/module.h>
16#include <linux/ioport.h>
17#include <linux/init.h>
18#include <linux/console.h>
19#include <linux/delay.h>
20#include <linux/platform_device.h>
21#include <linux/pci.h>
22#include <linux/serial_core.h>
23#include <linux/serial.h>
24#include <linux/tty.h>
25#include <linux/tty_flip.h>
26
27#include <linux/io.h>
28
29#define PASS_LIMIT 256
30
31#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
32/* "ttyS" is used for standard serial driver */
33#define TXX9_TTY_NAME "ttyTX"
34#define TXX9_TTY_MINOR_START 196
35#define TXX9_TTY_MAJOR 204
36#else
37/* acts like standard serial driver */
38#define TXX9_TTY_NAME "ttyS"
39#define TXX9_TTY_MINOR_START 64
40#define TXX9_TTY_MAJOR TTY_MAJOR
41#endif
42
43/* flag aliases */
44#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
45#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
46
47#ifdef CONFIG_PCI
48/* support for Toshiba TC86C001 SIO */
49#define ENABLE_SERIAL_TXX9_PCI
50#endif
51
52/*
53 * Number of serial ports
54 */
55#define UART_NR CONFIG_SERIAL_TXX9_NR_UARTS
56
57#define TXX9_REGION_SIZE 0x24
58
59/* TXX9 Serial Registers */
60#define TXX9_SILCR 0x00
61#define TXX9_SIDICR 0x04
62#define TXX9_SIDISR 0x08
63#define TXX9_SICISR 0x0c
64#define TXX9_SIFCR 0x10
65#define TXX9_SIFLCR 0x14
66#define TXX9_SIBGR 0x18
67#define TXX9_SITFIFO 0x1c
68#define TXX9_SIRFIFO 0x20
69
70/* SILCR : Line Control */
71#define TXX9_SILCR_SCS_MASK 0x00000060
72#define TXX9_SILCR_SCS_IMCLK 0x00000000
73#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
74#define TXX9_SILCR_SCS_SCLK 0x00000040
75#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
76#define TXX9_SILCR_UEPS 0x00000010
77#define TXX9_SILCR_UPEN 0x00000008
78#define TXX9_SILCR_USBL_MASK 0x00000004
79#define TXX9_SILCR_USBL_1BIT 0x00000000
80#define TXX9_SILCR_USBL_2BIT 0x00000004
81#define TXX9_SILCR_UMODE_MASK 0x00000003
82#define TXX9_SILCR_UMODE_8BIT 0x00000000
83#define TXX9_SILCR_UMODE_7BIT 0x00000001
84
85/* SIDICR : DMA/Int. Control */
86#define TXX9_SIDICR_TDE 0x00008000
87#define TXX9_SIDICR_RDE 0x00004000
88#define TXX9_SIDICR_TIE 0x00002000
89#define TXX9_SIDICR_RIE 0x00001000
90#define TXX9_SIDICR_SPIE 0x00000800
91#define TXX9_SIDICR_CTSAC 0x00000600
92#define TXX9_SIDICR_STIE_MASK 0x0000003f
93#define TXX9_SIDICR_STIE_OERS 0x00000020
94#define TXX9_SIDICR_STIE_CTSS 0x00000010
95#define TXX9_SIDICR_STIE_RBRKD 0x00000008
96#define TXX9_SIDICR_STIE_TRDY 0x00000004
97#define TXX9_SIDICR_STIE_TXALS 0x00000002
98#define TXX9_SIDICR_STIE_UBRKD 0x00000001
99
100/* SIDISR : DMA/Int. Status */
101#define TXX9_SIDISR_UBRK 0x00008000
102#define TXX9_SIDISR_UVALID 0x00004000
103#define TXX9_SIDISR_UFER 0x00002000
104#define TXX9_SIDISR_UPER 0x00001000
105#define TXX9_SIDISR_UOER 0x00000800
106#define TXX9_SIDISR_ERI 0x00000400
107#define TXX9_SIDISR_TOUT 0x00000200
108#define TXX9_SIDISR_TDIS 0x00000100
109#define TXX9_SIDISR_RDIS 0x00000080
110#define TXX9_SIDISR_STIS 0x00000040
111#define TXX9_SIDISR_RFDN_MASK 0x0000001f
112
113/* SICISR : Change Int. Status */
114#define TXX9_SICISR_OERS 0x00000020
115#define TXX9_SICISR_CTSS 0x00000010
116#define TXX9_SICISR_RBRKD 0x00000008
117#define TXX9_SICISR_TRDY 0x00000004
118#define TXX9_SICISR_TXALS 0x00000002
119#define TXX9_SICISR_UBRKD 0x00000001
120
121/* SIFCR : FIFO Control */
122#define TXX9_SIFCR_SWRST 0x00008000
123#define TXX9_SIFCR_RDIL_MASK 0x00000180
124#define TXX9_SIFCR_RDIL_1 0x00000000
125#define TXX9_SIFCR_RDIL_4 0x00000080
126#define TXX9_SIFCR_RDIL_8 0x00000100
127#define TXX9_SIFCR_RDIL_12 0x00000180
128#define TXX9_SIFCR_RDIL_MAX 0x00000180
129#define TXX9_SIFCR_TDIL_MASK 0x00000018
130#define TXX9_SIFCR_TDIL_1 0x00000000
131#define TXX9_SIFCR_TDIL_4 0x00000001
132#define TXX9_SIFCR_TDIL_8 0x00000010
133#define TXX9_SIFCR_TDIL_MAX 0x00000010
134#define TXX9_SIFCR_TFRST 0x00000004
135#define TXX9_SIFCR_RFRST 0x00000002
136#define TXX9_SIFCR_FRSTE 0x00000001
137#define TXX9_SIO_TX_FIFO 8
138#define TXX9_SIO_RX_FIFO 16
139
140/* SIFLCR : Flow Control */
141#define TXX9_SIFLCR_RCS 0x00001000
142#define TXX9_SIFLCR_TES 0x00000800
143#define TXX9_SIFLCR_RTSSC 0x00000200
144#define TXX9_SIFLCR_RSDE 0x00000100
145#define TXX9_SIFLCR_TSDE 0x00000080
146#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
147#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
148#define TXX9_SIFLCR_TBRK 0x00000001
149
150/* SIBGR : Baudrate Control */
151#define TXX9_SIBGR_BCLK_MASK 0x00000300
152#define TXX9_SIBGR_BCLK_T0 0x00000000
153#define TXX9_SIBGR_BCLK_T2 0x00000100
154#define TXX9_SIBGR_BCLK_T4 0x00000200
155#define TXX9_SIBGR_BCLK_T6 0x00000300
156#define TXX9_SIBGR_BRD_MASK 0x000000ff
157
158static inline unsigned int sio_in(struct uart_port *up, int offset)
159{
160 switch (up->iotype) {
161 default:
162 return __raw_readl(up->membase + offset);
163 case UPIO_PORT:
164 return inl(up->iobase + offset);
165 }
166}
167
168static inline void
169sio_out(struct uart_port *up, int offset, int value)
170{
171 switch (up->iotype) {
172 default:
173 __raw_writel(value, up->membase + offset);
174 break;
175 case UPIO_PORT:
176 outl(value, up->iobase + offset);
177 break;
178 }
179}
180
181static inline void
182sio_mask(struct uart_port *up, int offset, unsigned int value)
183{
184 sio_out(up, offset, sio_in(up, offset) & ~value);
185}
186static inline void
187sio_set(struct uart_port *up, int offset, unsigned int value)
188{
189 sio_out(up, offset, sio_in(up, offset) | value);
190}
191
192static inline void
193sio_quot_set(struct uart_port *up, int quot)
194{
195 quot >>= 1;
196 if (quot < 256)
197 sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
198 else if (quot < (256 << 2))
199 sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
200 else if (quot < (256 << 4))
201 sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
202 else if (quot < (256 << 6))
203 sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
204 else
205 sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
206}
207
208static void serial_txx9_stop_tx(struct uart_port *up)
209{
210 sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
211}
212
213static void serial_txx9_start_tx(struct uart_port *up)
214{
215 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
216}
217
218static void serial_txx9_stop_rx(struct uart_port *up)
219{
220 up->read_status_mask &= ~TXX9_SIDISR_RDIS;
221}
222
223static void serial_txx9_initialize(struct uart_port *up)
224{
225 unsigned int tmout = 10000;
226
227 sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
228 /* TX4925 BUG WORKAROUND. Accessing SIOC register
229 * immediately after soft reset causes bus error. */
230 udelay(1);
231 while ((sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST) && --tmout)
232 udelay(1);
233 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
234 sio_set(up, TXX9_SIFCR,
235 TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
236 /* initial settings */
237 sio_out(up, TXX9_SILCR,
238 TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
239 ((up->flags & UPF_TXX9_USE_SCLK) ?
240 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
241 sio_quot_set(up, uart_get_divisor(up, 9600));
242 sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
243 sio_out(up, TXX9_SIDICR, 0);
244}
245
246static inline void
247receive_chars(struct uart_port *up, unsigned int *status)
248{
249 unsigned int disr = *status;
250 int max_count = 256;
251 unsigned int next_ignore_status_mask;
252 u8 ch, flag;
253
254 do {
255 ch = sio_in(up, TXX9_SIRFIFO);
256 flag = TTY_NORMAL;
257 up->icount.rx++;
258
259 /* mask out RFDN_MASK bit added by previous overrun */
260 next_ignore_status_mask =
261 up->ignore_status_mask & ~TXX9_SIDISR_RFDN_MASK;
262 if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
263 TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
264 /*
265 * For statistics only
266 */
267 if (disr & TXX9_SIDISR_UBRK) {
268 disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
269 up->icount.brk++;
270 /*
271 * We do the SysRQ and SAK checking
272 * here because otherwise the break
273 * may get masked by ignore_status_mask
274 * or read_status_mask.
275 */
276 if (uart_handle_break(up))
277 goto ignore_char;
278 } else if (disr & TXX9_SIDISR_UPER)
279 up->icount.parity++;
280 else if (disr & TXX9_SIDISR_UFER)
281 up->icount.frame++;
282 if (disr & TXX9_SIDISR_UOER) {
283 up->icount.overrun++;
284 /*
285 * The receiver read buffer still hold
286 * a char which caused overrun.
287 * Ignore next char by adding RFDN_MASK
288 * to ignore_status_mask temporarily.
289 */
290 next_ignore_status_mask |=
291 TXX9_SIDISR_RFDN_MASK;
292 }
293
294 /*
295 * Mask off conditions which should be ingored.
296 */
297 disr &= up->read_status_mask;
298
299 if (disr & TXX9_SIDISR_UBRK) {
300 flag = TTY_BREAK;
301 } else if (disr & TXX9_SIDISR_UPER)
302 flag = TTY_PARITY;
303 else if (disr & TXX9_SIDISR_UFER)
304 flag = TTY_FRAME;
305 }
306 if (uart_handle_sysrq_char(up, ch))
307 goto ignore_char;
308
309 uart_insert_char(up, disr, TXX9_SIDISR_UOER, ch, flag);
310
311 ignore_char:
312 up->ignore_status_mask = next_ignore_status_mask;
313 disr = sio_in(up, TXX9_SIDISR);
314 } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
315
316 tty_flip_buffer_push(&up->state->port);
317
318 *status = disr;
319}
320
321static inline void transmit_chars(struct uart_port *up)
322{
323 u8 ch;
324
325 uart_port_tx_limited(up, ch, TXX9_SIO_TX_FIFO,
326 true,
327 sio_out(up, TXX9_SITFIFO, ch),
328 ({}));
329}
330
331static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id)
332{
333 int pass_counter = 0;
334 struct uart_port *up = dev_id;
335 unsigned int status;
336
337 while (1) {
338 uart_port_lock(up);
339 status = sio_in(up, TXX9_SIDISR);
340 if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
341 status &= ~TXX9_SIDISR_TDIS;
342 if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
343 TXX9_SIDISR_TOUT))) {
344 uart_port_unlock(up);
345 break;
346 }
347
348 if (status & TXX9_SIDISR_RDIS)
349 receive_chars(up, &status);
350 if (status & TXX9_SIDISR_TDIS)
351 transmit_chars(up);
352 /* Clear TX/RX Int. Status */
353 sio_mask(up, TXX9_SIDISR,
354 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
355 TXX9_SIDISR_TOUT);
356 uart_port_unlock(up);
357
358 if (pass_counter++ > PASS_LIMIT)
359 break;
360 }
361
362 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
363}
364
365static unsigned int serial_txx9_tx_empty(struct uart_port *up)
366{
367 unsigned long flags;
368 unsigned int ret;
369
370 uart_port_lock_irqsave(up, &flags);
371 ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
372 uart_port_unlock_irqrestore(up, flags);
373
374 return ret;
375}
376
377static unsigned int serial_txx9_get_mctrl(struct uart_port *up)
378{
379 unsigned int ret;
380
381 /* no modem control lines */
382 ret = TIOCM_CAR | TIOCM_DSR;
383 ret |= (sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS;
384 ret |= (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS;
385
386 return ret;
387}
388
389static void serial_txx9_set_mctrl(struct uart_port *up, unsigned int mctrl)
390{
391
392 if (mctrl & TIOCM_RTS)
393 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
394 else
395 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
396}
397
398static void serial_txx9_break_ctl(struct uart_port *up, int break_state)
399{
400 unsigned long flags;
401
402 uart_port_lock_irqsave(up, &flags);
403 if (break_state == -1)
404 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
405 else
406 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
407 uart_port_unlock_irqrestore(up, flags);
408}
409
410#if defined(CONFIG_SERIAL_TXX9_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
411/*
412 * Wait for transmitter & holding register to empty
413 */
414static void wait_for_xmitr(struct uart_port *up)
415{
416 unsigned int tmout = 10000;
417
418 /* Wait up to 10ms for the character(s) to be sent. */
419 while (--tmout &&
420 !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
421 udelay(1);
422
423 /* Wait up to 1s for flow control if necessary */
424 if (up->flags & UPF_CONS_FLOW) {
425 tmout = 1000000;
426 while (--tmout &&
427 (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
428 udelay(1);
429 }
430}
431#endif
432
433#ifdef CONFIG_CONSOLE_POLL
434/*
435 * Console polling routines for writing and reading from the uart while
436 * in an interrupt or debug context.
437 */
438
439static int serial_txx9_get_poll_char(struct uart_port *up)
440{
441 unsigned int ier;
442 unsigned char c;
443
444 /*
445 * First save the IER then disable the interrupts
446 */
447 ier = sio_in(up, TXX9_SIDICR);
448 sio_out(up, TXX9_SIDICR, 0);
449
450 while (sio_in(up, TXX9_SIDISR) & TXX9_SIDISR_UVALID)
451 ;
452
453 c = sio_in(up, TXX9_SIRFIFO);
454
455 /*
456 * Finally, clear RX interrupt status
457 * and restore the IER
458 */
459 sio_mask(up, TXX9_SIDISR, TXX9_SIDISR_RDIS);
460 sio_out(up, TXX9_SIDICR, ier);
461 return c;
462}
463
464
465static void serial_txx9_put_poll_char(struct uart_port *up, unsigned char c)
466{
467 unsigned int ier;
468
469 /*
470 * First save the IER then disable the interrupts
471 */
472 ier = sio_in(up, TXX9_SIDICR);
473 sio_out(up, TXX9_SIDICR, 0);
474
475 wait_for_xmitr(up);
476 /*
477 * Send the character out.
478 */
479 sio_out(up, TXX9_SITFIFO, c);
480
481 /*
482 * Finally, wait for transmitter to become empty
483 * and restore the IER
484 */
485 wait_for_xmitr(up);
486 sio_out(up, TXX9_SIDICR, ier);
487}
488
489#endif /* CONFIG_CONSOLE_POLL */
490
491static int serial_txx9_startup(struct uart_port *up)
492{
493 unsigned long flags;
494 int retval;
495
496 /*
497 * Clear the FIFO buffers and disable them.
498 * (they will be reenabled in set_termios())
499 */
500 sio_set(up, TXX9_SIFCR,
501 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
502 /* clear reset */
503 sio_mask(up, TXX9_SIFCR,
504 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
505 sio_out(up, TXX9_SIDICR, 0);
506
507 /*
508 * Clear the interrupt registers.
509 */
510 sio_out(up, TXX9_SIDISR, 0);
511
512 retval = request_irq(up->irq, serial_txx9_interrupt,
513 IRQF_SHARED, "serial_txx9", up);
514 if (retval)
515 return retval;
516
517 /*
518 * Now, initialize the UART
519 */
520 uart_port_lock_irqsave(up, &flags);
521 serial_txx9_set_mctrl(up, up->mctrl);
522 uart_port_unlock_irqrestore(up, flags);
523
524 /* Enable RX/TX */
525 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
526
527 /*
528 * Finally, enable interrupts.
529 */
530 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
531
532 return 0;
533}
534
535static void serial_txx9_shutdown(struct uart_port *up)
536{
537 unsigned long flags;
538
539 /*
540 * Disable interrupts from this port
541 */
542 sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
543
544 uart_port_lock_irqsave(up, &flags);
545 serial_txx9_set_mctrl(up, up->mctrl);
546 uart_port_unlock_irqrestore(up, flags);
547
548 /*
549 * Disable break condition
550 */
551 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
552
553#ifdef CONFIG_SERIAL_TXX9_CONSOLE
554 if (up->cons && up->line == up->cons->index) {
555 free_irq(up->irq, up);
556 return;
557 }
558#endif
559 /* reset FIFOs */
560 sio_set(up, TXX9_SIFCR,
561 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
562 /* clear reset */
563 sio_mask(up, TXX9_SIFCR,
564 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
565
566 /* Disable RX/TX */
567 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
568
569 free_irq(up->irq, up);
570}
571
572static void
573serial_txx9_set_termios(struct uart_port *up, struct ktermios *termios,
574 const struct ktermios *old)
575{
576 unsigned int cval, fcr = 0;
577 unsigned long flags;
578 unsigned int baud, quot;
579
580 /*
581 * We don't support modem control lines.
582 */
583 termios->c_cflag &= ~(HUPCL | CMSPAR);
584 termios->c_cflag |= CLOCAL;
585
586 cval = sio_in(up, TXX9_SILCR);
587 /* byte size and parity */
588 cval &= ~TXX9_SILCR_UMODE_MASK;
589 switch (termios->c_cflag & CSIZE) {
590 case CS7:
591 cval |= TXX9_SILCR_UMODE_7BIT;
592 break;
593 default:
594 case CS5: /* not supported */
595 case CS6: /* not supported */
596 case CS8:
597 cval |= TXX9_SILCR_UMODE_8BIT;
598 termios->c_cflag &= ~CSIZE;
599 termios->c_cflag |= CS8;
600 break;
601 }
602
603 cval &= ~TXX9_SILCR_USBL_MASK;
604 if (termios->c_cflag & CSTOPB)
605 cval |= TXX9_SILCR_USBL_2BIT;
606 else
607 cval |= TXX9_SILCR_USBL_1BIT;
608 cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
609 if (termios->c_cflag & PARENB)
610 cval |= TXX9_SILCR_UPEN;
611 if (!(termios->c_cflag & PARODD))
612 cval |= TXX9_SILCR_UEPS;
613
614 /*
615 * Ask the core to calculate the divisor for us.
616 */
617 baud = uart_get_baud_rate(up, termios, old, 0, up->uartclk/16/2);
618 quot = uart_get_divisor(up, baud);
619
620 /* Set up FIFOs */
621 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
622 fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
623
624 /*
625 * Ok, we're now changing the port state. Do it with
626 * interrupts disabled.
627 */
628 uart_port_lock_irqsave(up, &flags);
629
630 /*
631 * Update the per-port timeout.
632 */
633 uart_update_timeout(up, termios->c_cflag, baud);
634
635 up->read_status_mask = TXX9_SIDISR_UOER |
636 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
637 if (termios->c_iflag & INPCK)
638 up->read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
639 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
640 up->read_status_mask |= TXX9_SIDISR_UBRK;
641
642 /*
643 * Characteres to ignore
644 */
645 up->ignore_status_mask = 0;
646 if (termios->c_iflag & IGNPAR)
647 up->ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
648 if (termios->c_iflag & IGNBRK) {
649 up->ignore_status_mask |= TXX9_SIDISR_UBRK;
650 /*
651 * If we're ignoring parity and break indicators,
652 * ignore overruns too (for real raw support).
653 */
654 if (termios->c_iflag & IGNPAR)
655 up->ignore_status_mask |= TXX9_SIDISR_UOER;
656 }
657
658 /*
659 * ignore all characters if CREAD is not set
660 */
661 if ((termios->c_cflag & CREAD) == 0)
662 up->ignore_status_mask |= TXX9_SIDISR_RDIS;
663
664 /* CTS flow control flag */
665 if ((termios->c_cflag & CRTSCTS) &&
666 (up->flags & UPF_TXX9_HAVE_CTS_LINE)) {
667 sio_set(up, TXX9_SIFLCR,
668 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
669 } else {
670 sio_mask(up, TXX9_SIFLCR,
671 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
672 }
673
674 sio_out(up, TXX9_SILCR, cval);
675 sio_quot_set(up, quot);
676 sio_out(up, TXX9_SIFCR, fcr);
677
678 serial_txx9_set_mctrl(up, up->mctrl);
679 uart_port_unlock_irqrestore(up, flags);
680}
681
682static void
683serial_txx9_pm(struct uart_port *port, unsigned int state,
684 unsigned int oldstate)
685{
686 /*
687 * If oldstate was -1 this is called from
688 * uart_configure_port(). In this case do not initialize the
689 * port now, because the port was already initialized (for
690 * non-console port) or should not be initialized here (for
691 * console port). If we initialized the port here we lose
692 * serial console settings.
693 */
694 if (state == 0 && oldstate != -1)
695 serial_txx9_initialize(port);
696}
697
698static int serial_txx9_request_resource(struct uart_port *up)
699{
700 unsigned int size = TXX9_REGION_SIZE;
701 int ret = 0;
702
703 switch (up->iotype) {
704 default:
705 if (!up->mapbase)
706 break;
707
708 if (!request_mem_region(up->mapbase, size, "serial_txx9")) {
709 ret = -EBUSY;
710 break;
711 }
712
713 if (up->flags & UPF_IOREMAP) {
714 up->membase = ioremap(up->mapbase, size);
715 if (!up->membase) {
716 release_mem_region(up->mapbase, size);
717 ret = -ENOMEM;
718 }
719 }
720 break;
721
722 case UPIO_PORT:
723 if (!request_region(up->iobase, size, "serial_txx9"))
724 ret = -EBUSY;
725 break;
726 }
727 return ret;
728}
729
730static void serial_txx9_release_resource(struct uart_port *up)
731{
732 unsigned int size = TXX9_REGION_SIZE;
733
734 switch (up->iotype) {
735 default:
736 if (!up->mapbase)
737 break;
738
739 if (up->flags & UPF_IOREMAP) {
740 iounmap(up->membase);
741 up->membase = NULL;
742 }
743
744 release_mem_region(up->mapbase, size);
745 break;
746
747 case UPIO_PORT:
748 release_region(up->iobase, size);
749 break;
750 }
751}
752
753static void serial_txx9_release_port(struct uart_port *up)
754{
755 serial_txx9_release_resource(up);
756}
757
758static int serial_txx9_request_port(struct uart_port *up)
759{
760 return serial_txx9_request_resource(up);
761}
762
763static void serial_txx9_config_port(struct uart_port *up, int uflags)
764{
765 int ret;
766
767 /*
768 * Find the region that we can probe for. This in turn
769 * tells us whether we can probe for the type of port.
770 */
771 ret = serial_txx9_request_resource(up);
772 if (ret < 0)
773 return;
774 up->type = PORT_TXX9;
775 up->fifosize = TXX9_SIO_TX_FIFO;
776
777#ifdef CONFIG_SERIAL_TXX9_CONSOLE
778 if (up->line == up->cons->index)
779 return;
780#endif
781 serial_txx9_initialize(up);
782}
783
784static const char *
785serial_txx9_type(struct uart_port *port)
786{
787 return "txx9";
788}
789
790static const struct uart_ops serial_txx9_pops = {
791 .tx_empty = serial_txx9_tx_empty,
792 .set_mctrl = serial_txx9_set_mctrl,
793 .get_mctrl = serial_txx9_get_mctrl,
794 .stop_tx = serial_txx9_stop_tx,
795 .start_tx = serial_txx9_start_tx,
796 .stop_rx = serial_txx9_stop_rx,
797 .break_ctl = serial_txx9_break_ctl,
798 .startup = serial_txx9_startup,
799 .shutdown = serial_txx9_shutdown,
800 .set_termios = serial_txx9_set_termios,
801 .pm = serial_txx9_pm,
802 .type = serial_txx9_type,
803 .release_port = serial_txx9_release_port,
804 .request_port = serial_txx9_request_port,
805 .config_port = serial_txx9_config_port,
806#ifdef CONFIG_CONSOLE_POLL
807 .poll_get_char = serial_txx9_get_poll_char,
808 .poll_put_char = serial_txx9_put_poll_char,
809#endif
810};
811
812static struct uart_port serial_txx9_ports[UART_NR];
813
814static void __init serial_txx9_register_ports(struct uart_driver *drv,
815 struct device *dev)
816{
817 int i;
818
819 for (i = 0; i < UART_NR; i++) {
820 struct uart_port *up = &serial_txx9_ports[i];
821
822 up->line = i;
823 up->ops = &serial_txx9_pops;
824 up->dev = dev;
825 if (up->iobase || up->mapbase)
826 uart_add_one_port(drv, up);
827 }
828}
829
830#ifdef CONFIG_SERIAL_TXX9_CONSOLE
831
832static void serial_txx9_console_putchar(struct uart_port *up, unsigned char ch)
833{
834 wait_for_xmitr(up);
835 sio_out(up, TXX9_SITFIFO, ch);
836}
837
838/*
839 * Print a string to the serial port trying not to disturb
840 * any possible real use of the port...
841 *
842 * The console_lock must be held when we get here.
843 */
844static void
845serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
846{
847 struct uart_port *up = &serial_txx9_ports[co->index];
848 unsigned int ier, flcr;
849
850 /*
851 * First save the UER then disable the interrupts
852 */
853 ier = sio_in(up, TXX9_SIDICR);
854 sio_out(up, TXX9_SIDICR, 0);
855 /*
856 * Disable flow-control if enabled (and unnecessary)
857 */
858 flcr = sio_in(up, TXX9_SIFLCR);
859 if (!(up->flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
860 sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
861
862 uart_console_write(up, s, count, serial_txx9_console_putchar);
863
864 /*
865 * Finally, wait for transmitter to become empty
866 * and restore the IER
867 */
868 wait_for_xmitr(up);
869 sio_out(up, TXX9_SIFLCR, flcr);
870 sio_out(up, TXX9_SIDICR, ier);
871}
872
873static int __init serial_txx9_console_setup(struct console *co, char *options)
874{
875 struct uart_port *up;
876 int baud = 9600;
877 int bits = 8;
878 int parity = 'n';
879 int flow = 'n';
880
881 /*
882 * Check whether an invalid uart number has been specified, and
883 * if so, search for the first available port that does have
884 * console support.
885 */
886 if (co->index >= UART_NR)
887 co->index = 0;
888 up = &serial_txx9_ports[co->index];
889 if (!up->ops)
890 return -ENODEV;
891
892 serial_txx9_initialize(up);
893
894 if (options)
895 uart_parse_options(options, &baud, &parity, &bits, &flow);
896
897 return uart_set_options(up, co, baud, parity, bits, flow);
898}
899
900static struct uart_driver serial_txx9_reg;
901static struct console serial_txx9_console = {
902 .name = TXX9_TTY_NAME,
903 .write = serial_txx9_console_write,
904 .device = uart_console_device,
905 .setup = serial_txx9_console_setup,
906 .flags = CON_PRINTBUFFER,
907 .index = -1,
908 .data = &serial_txx9_reg,
909};
910
911static int __init serial_txx9_console_init(void)
912{
913 register_console(&serial_txx9_console);
914 return 0;
915}
916console_initcall(serial_txx9_console_init);
917
918#define SERIAL_TXX9_CONSOLE &serial_txx9_console
919#else
920#define SERIAL_TXX9_CONSOLE NULL
921#endif
922
923static struct uart_driver serial_txx9_reg = {
924 .owner = THIS_MODULE,
925 .driver_name = "serial_txx9",
926 .dev_name = TXX9_TTY_NAME,
927 .major = TXX9_TTY_MAJOR,
928 .minor = TXX9_TTY_MINOR_START,
929 .nr = UART_NR,
930 .cons = SERIAL_TXX9_CONSOLE,
931};
932
933int __init early_serial_txx9_setup(struct uart_port *port)
934{
935 if (port->line >= ARRAY_SIZE(serial_txx9_ports))
936 return -ENODEV;
937
938 serial_txx9_ports[port->line] = *port;
939 serial_txx9_ports[port->line].ops = &serial_txx9_pops;
940 serial_txx9_ports[port->line].flags |=
941 UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
942 return 0;
943}
944
945static DEFINE_MUTEX(serial_txx9_mutex);
946
947/**
948 * serial_txx9_register_port - register a serial port
949 * @port: serial port template
950 *
951 * Configure the serial port specified by the request.
952 *
953 * The port is then probed and if necessary the IRQ is autodetected
954 * If this fails an error is returned.
955 *
956 * On success the port is ready to use and the line number is returned.
957 */
958static int serial_txx9_register_port(struct uart_port *port)
959{
960 int i;
961 struct uart_port *uart;
962 int ret = -ENOSPC;
963
964 mutex_lock(&serial_txx9_mutex);
965 for (i = 0; i < UART_NR; i++) {
966 uart = &serial_txx9_ports[i];
967 if (uart_match_port(uart, port)) {
968 uart_remove_one_port(&serial_txx9_reg, uart);
969 break;
970 }
971 }
972 if (i == UART_NR) {
973 /* Find unused port */
974 for (i = 0; i < UART_NR; i++) {
975 uart = &serial_txx9_ports[i];
976 if (!(uart->iobase || uart->mapbase))
977 break;
978 }
979 }
980 if (i < UART_NR) {
981 uart->iobase = port->iobase;
982 uart->membase = port->membase;
983 uart->irq = port->irq;
984 uart->uartclk = port->uartclk;
985 uart->iotype = port->iotype;
986 uart->flags = port->flags
987 | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
988 uart->mapbase = port->mapbase;
989 if (port->dev)
990 uart->dev = port->dev;
991 ret = uart_add_one_port(&serial_txx9_reg, uart);
992 if (ret == 0)
993 ret = uart->line;
994 }
995 mutex_unlock(&serial_txx9_mutex);
996 return ret;
997}
998
999/**
1000 * serial_txx9_unregister_port - remove a txx9 serial port at runtime
1001 * @line: serial line number
1002 *
1003 * Remove one serial port. This may not be called from interrupt
1004 * context. We hand the port back to the our control.
1005 */
1006static void serial_txx9_unregister_port(int line)
1007{
1008 struct uart_port *uart = &serial_txx9_ports[line];
1009
1010 mutex_lock(&serial_txx9_mutex);
1011 uart_remove_one_port(&serial_txx9_reg, uart);
1012 uart->flags = 0;
1013 uart->type = PORT_UNKNOWN;
1014 uart->iobase = 0;
1015 uart->mapbase = 0;
1016 uart->membase = NULL;
1017 uart->dev = NULL;
1018 mutex_unlock(&serial_txx9_mutex);
1019}
1020
1021/*
1022 * Register a set of serial devices attached to a platform device.
1023 */
1024static int serial_txx9_probe(struct platform_device *dev)
1025{
1026 struct uart_port *p = dev_get_platdata(&dev->dev);
1027 struct uart_port port;
1028 int ret, i;
1029
1030 memset(&port, 0, sizeof(struct uart_port));
1031 for (i = 0; p && p->uartclk != 0; p++, i++) {
1032 port.iobase = p->iobase;
1033 port.membase = p->membase;
1034 port.irq = p->irq;
1035 port.uartclk = p->uartclk;
1036 port.iotype = p->iotype;
1037 port.flags = p->flags;
1038 port.mapbase = p->mapbase;
1039 port.dev = &dev->dev;
1040 port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_TXX9_CONSOLE);
1041 ret = serial_txx9_register_port(&port);
1042 if (ret < 0) {
1043 dev_err(&dev->dev, "unable to register port at index %d "
1044 "(IO%lx MEM%llx IRQ%d): %d\n", i,
1045 p->iobase, (unsigned long long)p->mapbase,
1046 p->irq, ret);
1047 }
1048 }
1049 return 0;
1050}
1051
1052/*
1053 * Remove serial ports registered against a platform device.
1054 */
1055static void serial_txx9_remove(struct platform_device *dev)
1056{
1057 int i;
1058
1059 for (i = 0; i < UART_NR; i++) {
1060 struct uart_port *up = &serial_txx9_ports[i];
1061
1062 if (up->dev == &dev->dev)
1063 serial_txx9_unregister_port(i);
1064 }
1065}
1066
1067#ifdef CONFIG_PM
1068static int serial_txx9_suspend(struct platform_device *dev, pm_message_t state)
1069{
1070 int i;
1071
1072 for (i = 0; i < UART_NR; i++) {
1073 struct uart_port *up = &serial_txx9_ports[i];
1074
1075 if (up->type != PORT_UNKNOWN && up->dev == &dev->dev)
1076 uart_suspend_port(&serial_txx9_reg, up);
1077 }
1078
1079 return 0;
1080}
1081
1082static int serial_txx9_resume(struct platform_device *dev)
1083{
1084 int i;
1085
1086 for (i = 0; i < UART_NR; i++) {
1087 struct uart_port *up = &serial_txx9_ports[i];
1088
1089 if (up->type != PORT_UNKNOWN && up->dev == &dev->dev)
1090 uart_resume_port(&serial_txx9_reg, up);
1091 }
1092
1093 return 0;
1094}
1095#endif
1096
1097static struct platform_driver serial_txx9_plat_driver = {
1098 .probe = serial_txx9_probe,
1099 .remove_new = serial_txx9_remove,
1100#ifdef CONFIG_PM
1101 .suspend = serial_txx9_suspend,
1102 .resume = serial_txx9_resume,
1103#endif
1104 .driver = {
1105 .name = "serial_txx9",
1106 },
1107};
1108
1109#ifdef ENABLE_SERIAL_TXX9_PCI
1110/*
1111 * Probe one serial board. Unfortunately, there is no rhyme nor reason
1112 * to the arrangement of serial ports on a PCI card.
1113 */
1114static int
1115pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
1116{
1117 struct uart_port port;
1118 int line;
1119 int rc;
1120
1121 rc = pci_enable_device(dev);
1122 if (rc)
1123 return rc;
1124
1125 memset(&port, 0, sizeof(port));
1126 port.ops = &serial_txx9_pops;
1127 port.flags |= UPF_TXX9_HAVE_CTS_LINE;
1128 port.uartclk = 66670000;
1129 port.irq = dev->irq;
1130 port.iotype = UPIO_PORT;
1131 port.iobase = pci_resource_start(dev, 1);
1132 port.dev = &dev->dev;
1133 line = serial_txx9_register_port(&port);
1134 if (line < 0) {
1135 printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
1136 pci_disable_device(dev);
1137 return line;
1138 }
1139 pci_set_drvdata(dev, &serial_txx9_ports[line]);
1140
1141 return 0;
1142}
1143
1144static void pciserial_txx9_remove_one(struct pci_dev *dev)
1145{
1146 struct uart_port *up = pci_get_drvdata(dev);
1147
1148 if (up) {
1149 serial_txx9_unregister_port(up->line);
1150 pci_disable_device(dev);
1151 }
1152}
1153
1154#ifdef CONFIG_PM
1155static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
1156{
1157 struct uart_port *up = pci_get_drvdata(dev);
1158
1159 if (up)
1160 uart_suspend_port(&serial_txx9_reg, up);
1161 pci_save_state(dev);
1162 pci_set_power_state(dev, pci_choose_state(dev, state));
1163 return 0;
1164}
1165
1166static int pciserial_txx9_resume_one(struct pci_dev *dev)
1167{
1168 struct uart_port *up = pci_get_drvdata(dev);
1169
1170 pci_set_power_state(dev, PCI_D0);
1171 pci_restore_state(dev);
1172 if (up)
1173 uart_resume_port(&serial_txx9_reg, up);
1174 return 0;
1175}
1176#endif
1177
1178static const struct pci_device_id serial_txx9_pci_tbl[] = {
1179 { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC) },
1180 { 0, }
1181};
1182
1183static struct pci_driver serial_txx9_pci_driver = {
1184 .name = "serial_txx9",
1185 .probe = pciserial_txx9_init_one,
1186 .remove = pciserial_txx9_remove_one,
1187#ifdef CONFIG_PM
1188 .suspend = pciserial_txx9_suspend_one,
1189 .resume = pciserial_txx9_resume_one,
1190#endif
1191 .id_table = serial_txx9_pci_tbl,
1192};
1193
1194MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
1195#endif /* ENABLE_SERIAL_TXX9_PCI */
1196
1197static struct platform_device *serial_txx9_plat_devs;
1198
1199static int __init serial_txx9_init(void)
1200{
1201 int ret;
1202
1203 ret = uart_register_driver(&serial_txx9_reg);
1204 if (ret)
1205 goto out;
1206
1207 serial_txx9_plat_devs = platform_device_alloc("serial_txx9", -1);
1208 if (!serial_txx9_plat_devs) {
1209 ret = -ENOMEM;
1210 goto unreg_uart_drv;
1211 }
1212
1213 ret = platform_device_add(serial_txx9_plat_devs);
1214 if (ret)
1215 goto put_dev;
1216
1217 serial_txx9_register_ports(&serial_txx9_reg,
1218 &serial_txx9_plat_devs->dev);
1219
1220 ret = platform_driver_register(&serial_txx9_plat_driver);
1221 if (ret)
1222 goto del_dev;
1223
1224#ifdef ENABLE_SERIAL_TXX9_PCI
1225 ret = pci_register_driver(&serial_txx9_pci_driver);
1226 if (ret) {
1227 platform_driver_unregister(&serial_txx9_plat_driver);
1228 }
1229#endif
1230 if (ret == 0)
1231 goto out;
1232
1233 del_dev:
1234 platform_device_del(serial_txx9_plat_devs);
1235 put_dev:
1236 platform_device_put(serial_txx9_plat_devs);
1237 unreg_uart_drv:
1238 uart_unregister_driver(&serial_txx9_reg);
1239 out:
1240 return ret;
1241}
1242
1243static void __exit serial_txx9_exit(void)
1244{
1245 int i;
1246
1247#ifdef ENABLE_SERIAL_TXX9_PCI
1248 pci_unregister_driver(&serial_txx9_pci_driver);
1249#endif
1250 platform_driver_unregister(&serial_txx9_plat_driver);
1251 platform_device_unregister(serial_txx9_plat_devs);
1252 for (i = 0; i < UART_NR; i++) {
1253 struct uart_port *up = &serial_txx9_ports[i];
1254 if (up->iobase || up->mapbase)
1255 uart_remove_one_port(&serial_txx9_reg, up);
1256 }
1257
1258 uart_unregister_driver(&serial_txx9_reg);
1259}
1260
1261module_init(serial_txx9_init);
1262module_exit(serial_txx9_exit);
1263
1264MODULE_LICENSE("GPL");
1265MODULE_DESCRIPTION("TX39/49 serial driver");
1266
1267MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);
1/*
2 * Derived from many drivers using generic_serial interface,
3 * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
4 * (was in Linux/VR tree) by Jim Pick.
5 *
6 * Copyright (C) 1999 Harald Koerfgen
7 * Copyright (C) 2000 Jim Pick <jim@jimpick.com>
8 * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
9 * Copyright (C) 2000-2002 Toshiba Corporation
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License version 2 as
13 * published by the Free Software Foundation.
14 *
15 * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
16 */
17
18#if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
19#define SUPPORT_SYSRQ
20#endif
21
22#include <linux/module.h>
23#include <linux/ioport.h>
24#include <linux/init.h>
25#include <linux/console.h>
26#include <linux/delay.h>
27#include <linux/platform_device.h>
28#include <linux/pci.h>
29#include <linux/serial_core.h>
30#include <linux/serial.h>
31
32#include <asm/io.h>
33
34static char *serial_version = "1.11";
35static char *serial_name = "TX39/49 Serial driver";
36
37#define PASS_LIMIT 256
38
39#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
40/* "ttyS" is used for standard serial driver */
41#define TXX9_TTY_NAME "ttyTX"
42#define TXX9_TTY_MINOR_START 196
43#define TXX9_TTY_MAJOR 204
44#else
45/* acts like standard serial driver */
46#define TXX9_TTY_NAME "ttyS"
47#define TXX9_TTY_MINOR_START 64
48#define TXX9_TTY_MAJOR TTY_MAJOR
49#endif
50
51/* flag aliases */
52#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
53#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
54
55#ifdef CONFIG_PCI
56/* support for Toshiba TC86C001 SIO */
57#define ENABLE_SERIAL_TXX9_PCI
58#endif
59
60/*
61 * Number of serial ports
62 */
63#define UART_NR CONFIG_SERIAL_TXX9_NR_UARTS
64
65struct uart_txx9_port {
66 struct uart_port port;
67 /* No additional info for now */
68};
69
70#define TXX9_REGION_SIZE 0x24
71
72/* TXX9 Serial Registers */
73#define TXX9_SILCR 0x00
74#define TXX9_SIDICR 0x04
75#define TXX9_SIDISR 0x08
76#define TXX9_SICISR 0x0c
77#define TXX9_SIFCR 0x10
78#define TXX9_SIFLCR 0x14
79#define TXX9_SIBGR 0x18
80#define TXX9_SITFIFO 0x1c
81#define TXX9_SIRFIFO 0x20
82
83/* SILCR : Line Control */
84#define TXX9_SILCR_SCS_MASK 0x00000060
85#define TXX9_SILCR_SCS_IMCLK 0x00000000
86#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
87#define TXX9_SILCR_SCS_SCLK 0x00000040
88#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
89#define TXX9_SILCR_UEPS 0x00000010
90#define TXX9_SILCR_UPEN 0x00000008
91#define TXX9_SILCR_USBL_MASK 0x00000004
92#define TXX9_SILCR_USBL_1BIT 0x00000000
93#define TXX9_SILCR_USBL_2BIT 0x00000004
94#define TXX9_SILCR_UMODE_MASK 0x00000003
95#define TXX9_SILCR_UMODE_8BIT 0x00000000
96#define TXX9_SILCR_UMODE_7BIT 0x00000001
97
98/* SIDICR : DMA/Int. Control */
99#define TXX9_SIDICR_TDE 0x00008000
100#define TXX9_SIDICR_RDE 0x00004000
101#define TXX9_SIDICR_TIE 0x00002000
102#define TXX9_SIDICR_RIE 0x00001000
103#define TXX9_SIDICR_SPIE 0x00000800
104#define TXX9_SIDICR_CTSAC 0x00000600
105#define TXX9_SIDICR_STIE_MASK 0x0000003f
106#define TXX9_SIDICR_STIE_OERS 0x00000020
107#define TXX9_SIDICR_STIE_CTSS 0x00000010
108#define TXX9_SIDICR_STIE_RBRKD 0x00000008
109#define TXX9_SIDICR_STIE_TRDY 0x00000004
110#define TXX9_SIDICR_STIE_TXALS 0x00000002
111#define TXX9_SIDICR_STIE_UBRKD 0x00000001
112
113/* SIDISR : DMA/Int. Status */
114#define TXX9_SIDISR_UBRK 0x00008000
115#define TXX9_SIDISR_UVALID 0x00004000
116#define TXX9_SIDISR_UFER 0x00002000
117#define TXX9_SIDISR_UPER 0x00001000
118#define TXX9_SIDISR_UOER 0x00000800
119#define TXX9_SIDISR_ERI 0x00000400
120#define TXX9_SIDISR_TOUT 0x00000200
121#define TXX9_SIDISR_TDIS 0x00000100
122#define TXX9_SIDISR_RDIS 0x00000080
123#define TXX9_SIDISR_STIS 0x00000040
124#define TXX9_SIDISR_RFDN_MASK 0x0000001f
125
126/* SICISR : Change Int. Status */
127#define TXX9_SICISR_OERS 0x00000020
128#define TXX9_SICISR_CTSS 0x00000010
129#define TXX9_SICISR_RBRKD 0x00000008
130#define TXX9_SICISR_TRDY 0x00000004
131#define TXX9_SICISR_TXALS 0x00000002
132#define TXX9_SICISR_UBRKD 0x00000001
133
134/* SIFCR : FIFO Control */
135#define TXX9_SIFCR_SWRST 0x00008000
136#define TXX9_SIFCR_RDIL_MASK 0x00000180
137#define TXX9_SIFCR_RDIL_1 0x00000000
138#define TXX9_SIFCR_RDIL_4 0x00000080
139#define TXX9_SIFCR_RDIL_8 0x00000100
140#define TXX9_SIFCR_RDIL_12 0x00000180
141#define TXX9_SIFCR_RDIL_MAX 0x00000180
142#define TXX9_SIFCR_TDIL_MASK 0x00000018
143#define TXX9_SIFCR_TDIL_MASK 0x00000018
144#define TXX9_SIFCR_TDIL_1 0x00000000
145#define TXX9_SIFCR_TDIL_4 0x00000001
146#define TXX9_SIFCR_TDIL_8 0x00000010
147#define TXX9_SIFCR_TDIL_MAX 0x00000010
148#define TXX9_SIFCR_TFRST 0x00000004
149#define TXX9_SIFCR_RFRST 0x00000002
150#define TXX9_SIFCR_FRSTE 0x00000001
151#define TXX9_SIO_TX_FIFO 8
152#define TXX9_SIO_RX_FIFO 16
153
154/* SIFLCR : Flow Control */
155#define TXX9_SIFLCR_RCS 0x00001000
156#define TXX9_SIFLCR_TES 0x00000800
157#define TXX9_SIFLCR_RTSSC 0x00000200
158#define TXX9_SIFLCR_RSDE 0x00000100
159#define TXX9_SIFLCR_TSDE 0x00000080
160#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
161#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
162#define TXX9_SIFLCR_TBRK 0x00000001
163
164/* SIBGR : Baudrate Control */
165#define TXX9_SIBGR_BCLK_MASK 0x00000300
166#define TXX9_SIBGR_BCLK_T0 0x00000000
167#define TXX9_SIBGR_BCLK_T2 0x00000100
168#define TXX9_SIBGR_BCLK_T4 0x00000200
169#define TXX9_SIBGR_BCLK_T6 0x00000300
170#define TXX9_SIBGR_BRD_MASK 0x000000ff
171
172static inline unsigned int sio_in(struct uart_txx9_port *up, int offset)
173{
174 switch (up->port.iotype) {
175 default:
176 return __raw_readl(up->port.membase + offset);
177 case UPIO_PORT:
178 return inl(up->port.iobase + offset);
179 }
180}
181
182static inline void
183sio_out(struct uart_txx9_port *up, int offset, int value)
184{
185 switch (up->port.iotype) {
186 default:
187 __raw_writel(value, up->port.membase + offset);
188 break;
189 case UPIO_PORT:
190 outl(value, up->port.iobase + offset);
191 break;
192 }
193}
194
195static inline void
196sio_mask(struct uart_txx9_port *up, int offset, unsigned int value)
197{
198 sio_out(up, offset, sio_in(up, offset) & ~value);
199}
200static inline void
201sio_set(struct uart_txx9_port *up, int offset, unsigned int value)
202{
203 sio_out(up, offset, sio_in(up, offset) | value);
204}
205
206static inline void
207sio_quot_set(struct uart_txx9_port *up, int quot)
208{
209 quot >>= 1;
210 if (quot < 256)
211 sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
212 else if (quot < (256 << 2))
213 sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
214 else if (quot < (256 << 4))
215 sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
216 else if (quot < (256 << 6))
217 sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
218 else
219 sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
220}
221
222static struct uart_txx9_port *to_uart_txx9_port(struct uart_port *port)
223{
224 return container_of(port, struct uart_txx9_port, port);
225}
226
227static void serial_txx9_stop_tx(struct uart_port *port)
228{
229 struct uart_txx9_port *up = to_uart_txx9_port(port);
230 sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
231}
232
233static void serial_txx9_start_tx(struct uart_port *port)
234{
235 struct uart_txx9_port *up = to_uart_txx9_port(port);
236 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
237}
238
239static void serial_txx9_stop_rx(struct uart_port *port)
240{
241 struct uart_txx9_port *up = to_uart_txx9_port(port);
242 up->port.read_status_mask &= ~TXX9_SIDISR_RDIS;
243}
244
245static void serial_txx9_enable_ms(struct uart_port *port)
246{
247 /* TXX9-SIO can not control DTR... */
248}
249
250static void serial_txx9_initialize(struct uart_port *port)
251{
252 struct uart_txx9_port *up = to_uart_txx9_port(port);
253 unsigned int tmout = 10000;
254
255 sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
256 /* TX4925 BUG WORKAROUND. Accessing SIOC register
257 * immediately after soft reset causes bus error. */
258 mmiowb();
259 udelay(1);
260 while ((sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST) && --tmout)
261 udelay(1);
262 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
263 sio_set(up, TXX9_SIFCR,
264 TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
265 /* initial settings */
266 sio_out(up, TXX9_SILCR,
267 TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
268 ((up->port.flags & UPF_TXX9_USE_SCLK) ?
269 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
270 sio_quot_set(up, uart_get_divisor(port, 9600));
271 sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
272 sio_out(up, TXX9_SIDICR, 0);
273}
274
275static inline void
276receive_chars(struct uart_txx9_port *up, unsigned int *status)
277{
278 struct tty_struct *tty = up->port.state->port.tty;
279 unsigned char ch;
280 unsigned int disr = *status;
281 int max_count = 256;
282 char flag;
283 unsigned int next_ignore_status_mask;
284
285 do {
286 ch = sio_in(up, TXX9_SIRFIFO);
287 flag = TTY_NORMAL;
288 up->port.icount.rx++;
289
290 /* mask out RFDN_MASK bit added by previous overrun */
291 next_ignore_status_mask =
292 up->port.ignore_status_mask & ~TXX9_SIDISR_RFDN_MASK;
293 if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
294 TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
295 /*
296 * For statistics only
297 */
298 if (disr & TXX9_SIDISR_UBRK) {
299 disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
300 up->port.icount.brk++;
301 /*
302 * We do the SysRQ and SAK checking
303 * here because otherwise the break
304 * may get masked by ignore_status_mask
305 * or read_status_mask.
306 */
307 if (uart_handle_break(&up->port))
308 goto ignore_char;
309 } else if (disr & TXX9_SIDISR_UPER)
310 up->port.icount.parity++;
311 else if (disr & TXX9_SIDISR_UFER)
312 up->port.icount.frame++;
313 if (disr & TXX9_SIDISR_UOER) {
314 up->port.icount.overrun++;
315 /*
316 * The receiver read buffer still hold
317 * a char which caused overrun.
318 * Ignore next char by adding RFDN_MASK
319 * to ignore_status_mask temporarily.
320 */
321 next_ignore_status_mask |=
322 TXX9_SIDISR_RFDN_MASK;
323 }
324
325 /*
326 * Mask off conditions which should be ingored.
327 */
328 disr &= up->port.read_status_mask;
329
330 if (disr & TXX9_SIDISR_UBRK) {
331 flag = TTY_BREAK;
332 } else if (disr & TXX9_SIDISR_UPER)
333 flag = TTY_PARITY;
334 else if (disr & TXX9_SIDISR_UFER)
335 flag = TTY_FRAME;
336 }
337 if (uart_handle_sysrq_char(&up->port, ch))
338 goto ignore_char;
339
340 uart_insert_char(&up->port, disr, TXX9_SIDISR_UOER, ch, flag);
341
342 ignore_char:
343 up->port.ignore_status_mask = next_ignore_status_mask;
344 disr = sio_in(up, TXX9_SIDISR);
345 } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
346 spin_unlock(&up->port.lock);
347 tty_flip_buffer_push(tty);
348 spin_lock(&up->port.lock);
349 *status = disr;
350}
351
352static inline void transmit_chars(struct uart_txx9_port *up)
353{
354 struct circ_buf *xmit = &up->port.state->xmit;
355 int count;
356
357 if (up->port.x_char) {
358 sio_out(up, TXX9_SITFIFO, up->port.x_char);
359 up->port.icount.tx++;
360 up->port.x_char = 0;
361 return;
362 }
363 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
364 serial_txx9_stop_tx(&up->port);
365 return;
366 }
367
368 count = TXX9_SIO_TX_FIFO;
369 do {
370 sio_out(up, TXX9_SITFIFO, xmit->buf[xmit->tail]);
371 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
372 up->port.icount.tx++;
373 if (uart_circ_empty(xmit))
374 break;
375 } while (--count > 0);
376
377 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
378 uart_write_wakeup(&up->port);
379
380 if (uart_circ_empty(xmit))
381 serial_txx9_stop_tx(&up->port);
382}
383
384static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id)
385{
386 int pass_counter = 0;
387 struct uart_txx9_port *up = dev_id;
388 unsigned int status;
389
390 while (1) {
391 spin_lock(&up->port.lock);
392 status = sio_in(up, TXX9_SIDISR);
393 if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
394 status &= ~TXX9_SIDISR_TDIS;
395 if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
396 TXX9_SIDISR_TOUT))) {
397 spin_unlock(&up->port.lock);
398 break;
399 }
400
401 if (status & TXX9_SIDISR_RDIS)
402 receive_chars(up, &status);
403 if (status & TXX9_SIDISR_TDIS)
404 transmit_chars(up);
405 /* Clear TX/RX Int. Status */
406 sio_mask(up, TXX9_SIDISR,
407 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
408 TXX9_SIDISR_TOUT);
409 spin_unlock(&up->port.lock);
410
411 if (pass_counter++ > PASS_LIMIT)
412 break;
413 }
414
415 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
416}
417
418static unsigned int serial_txx9_tx_empty(struct uart_port *port)
419{
420 struct uart_txx9_port *up = to_uart_txx9_port(port);
421 unsigned long flags;
422 unsigned int ret;
423
424 spin_lock_irqsave(&up->port.lock, flags);
425 ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
426 spin_unlock_irqrestore(&up->port.lock, flags);
427
428 return ret;
429}
430
431static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
432{
433 struct uart_txx9_port *up = to_uart_txx9_port(port);
434 unsigned int ret;
435
436 /* no modem control lines */
437 ret = TIOCM_CAR | TIOCM_DSR;
438 ret |= (sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS;
439 ret |= (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS;
440
441 return ret;
442}
443
444static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl)
445{
446 struct uart_txx9_port *up = to_uart_txx9_port(port);
447
448 if (mctrl & TIOCM_RTS)
449 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
450 else
451 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
452}
453
454static void serial_txx9_break_ctl(struct uart_port *port, int break_state)
455{
456 struct uart_txx9_port *up = to_uart_txx9_port(port);
457 unsigned long flags;
458
459 spin_lock_irqsave(&up->port.lock, flags);
460 if (break_state == -1)
461 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
462 else
463 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
464 spin_unlock_irqrestore(&up->port.lock, flags);
465}
466
467#if defined(CONFIG_SERIAL_TXX9_CONSOLE) || (CONFIG_CONSOLE_POLL)
468/*
469 * Wait for transmitter & holding register to empty
470 */
471static void wait_for_xmitr(struct uart_txx9_port *up)
472{
473 unsigned int tmout = 10000;
474
475 /* Wait up to 10ms for the character(s) to be sent. */
476 while (--tmout &&
477 !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
478 udelay(1);
479
480 /* Wait up to 1s for flow control if necessary */
481 if (up->port.flags & UPF_CONS_FLOW) {
482 tmout = 1000000;
483 while (--tmout &&
484 (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
485 udelay(1);
486 }
487}
488#endif
489
490#ifdef CONFIG_CONSOLE_POLL
491/*
492 * Console polling routines for writing and reading from the uart while
493 * in an interrupt or debug context.
494 */
495
496static int serial_txx9_get_poll_char(struct uart_port *port)
497{
498 unsigned int ier;
499 unsigned char c;
500 struct uart_txx9_port *up = to_uart_txx9_port(port);
501
502 /*
503 * First save the IER then disable the interrupts
504 */
505 ier = sio_in(up, TXX9_SIDICR);
506 sio_out(up, TXX9_SIDICR, 0);
507
508 while (sio_in(up, TXX9_SIDISR) & TXX9_SIDISR_UVALID)
509 ;
510
511 c = sio_in(up, TXX9_SIRFIFO);
512
513 /*
514 * Finally, clear RX interrupt status
515 * and restore the IER
516 */
517 sio_mask(up, TXX9_SIDISR, TXX9_SIDISR_RDIS);
518 sio_out(up, TXX9_SIDICR, ier);
519 return c;
520}
521
522
523static void serial_txx9_put_poll_char(struct uart_port *port, unsigned char c)
524{
525 unsigned int ier;
526 struct uart_txx9_port *up = to_uart_txx9_port(port);
527
528 /*
529 * First save the IER then disable the interrupts
530 */
531 ier = sio_in(up, TXX9_SIDICR);
532 sio_out(up, TXX9_SIDICR, 0);
533
534 wait_for_xmitr(up);
535 /*
536 * Send the character out.
537 * If a LF, also do CR...
538 */
539 sio_out(up, TXX9_SITFIFO, c);
540 if (c == 10) {
541 wait_for_xmitr(up);
542 sio_out(up, TXX9_SITFIFO, 13);
543 }
544
545 /*
546 * Finally, wait for transmitter to become empty
547 * and restore the IER
548 */
549 wait_for_xmitr(up);
550 sio_out(up, TXX9_SIDICR, ier);
551}
552
553#endif /* CONFIG_CONSOLE_POLL */
554
555static int serial_txx9_startup(struct uart_port *port)
556{
557 struct uart_txx9_port *up = to_uart_txx9_port(port);
558 unsigned long flags;
559 int retval;
560
561 /*
562 * Clear the FIFO buffers and disable them.
563 * (they will be reenabled in set_termios())
564 */
565 sio_set(up, TXX9_SIFCR,
566 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
567 /* clear reset */
568 sio_mask(up, TXX9_SIFCR,
569 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
570 sio_out(up, TXX9_SIDICR, 0);
571
572 /*
573 * Clear the interrupt registers.
574 */
575 sio_out(up, TXX9_SIDISR, 0);
576
577 retval = request_irq(up->port.irq, serial_txx9_interrupt,
578 IRQF_SHARED, "serial_txx9", up);
579 if (retval)
580 return retval;
581
582 /*
583 * Now, initialize the UART
584 */
585 spin_lock_irqsave(&up->port.lock, flags);
586 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
587 spin_unlock_irqrestore(&up->port.lock, flags);
588
589 /* Enable RX/TX */
590 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
591
592 /*
593 * Finally, enable interrupts.
594 */
595 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
596
597 return 0;
598}
599
600static void serial_txx9_shutdown(struct uart_port *port)
601{
602 struct uart_txx9_port *up = to_uart_txx9_port(port);
603 unsigned long flags;
604
605 /*
606 * Disable interrupts from this port
607 */
608 sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
609
610 spin_lock_irqsave(&up->port.lock, flags);
611 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
612 spin_unlock_irqrestore(&up->port.lock, flags);
613
614 /*
615 * Disable break condition
616 */
617 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
618
619#ifdef CONFIG_SERIAL_TXX9_CONSOLE
620 if (up->port.cons && up->port.line == up->port.cons->index) {
621 free_irq(up->port.irq, up);
622 return;
623 }
624#endif
625 /* reset FIFOs */
626 sio_set(up, TXX9_SIFCR,
627 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
628 /* clear reset */
629 sio_mask(up, TXX9_SIFCR,
630 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
631
632 /* Disable RX/TX */
633 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
634
635 free_irq(up->port.irq, up);
636}
637
638static void
639serial_txx9_set_termios(struct uart_port *port, struct ktermios *termios,
640 struct ktermios *old)
641{
642 struct uart_txx9_port *up = to_uart_txx9_port(port);
643 unsigned int cval, fcr = 0;
644 unsigned long flags;
645 unsigned int baud, quot;
646
647 /*
648 * We don't support modem control lines.
649 */
650 termios->c_cflag &= ~(HUPCL | CMSPAR);
651 termios->c_cflag |= CLOCAL;
652
653 cval = sio_in(up, TXX9_SILCR);
654 /* byte size and parity */
655 cval &= ~TXX9_SILCR_UMODE_MASK;
656 switch (termios->c_cflag & CSIZE) {
657 case CS7:
658 cval |= TXX9_SILCR_UMODE_7BIT;
659 break;
660 default:
661 case CS5: /* not supported */
662 case CS6: /* not supported */
663 case CS8:
664 cval |= TXX9_SILCR_UMODE_8BIT;
665 break;
666 }
667
668 cval &= ~TXX9_SILCR_USBL_MASK;
669 if (termios->c_cflag & CSTOPB)
670 cval |= TXX9_SILCR_USBL_2BIT;
671 else
672 cval |= TXX9_SILCR_USBL_1BIT;
673 cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
674 if (termios->c_cflag & PARENB)
675 cval |= TXX9_SILCR_UPEN;
676 if (!(termios->c_cflag & PARODD))
677 cval |= TXX9_SILCR_UEPS;
678
679 /*
680 * Ask the core to calculate the divisor for us.
681 */
682 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16/2);
683 quot = uart_get_divisor(port, baud);
684
685 /* Set up FIFOs */
686 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
687 fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
688
689 /*
690 * Ok, we're now changing the port state. Do it with
691 * interrupts disabled.
692 */
693 spin_lock_irqsave(&up->port.lock, flags);
694
695 /*
696 * Update the per-port timeout.
697 */
698 uart_update_timeout(port, termios->c_cflag, baud);
699
700 up->port.read_status_mask = TXX9_SIDISR_UOER |
701 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
702 if (termios->c_iflag & INPCK)
703 up->port.read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
704 if (termios->c_iflag & (BRKINT | PARMRK))
705 up->port.read_status_mask |= TXX9_SIDISR_UBRK;
706
707 /*
708 * Characteres to ignore
709 */
710 up->port.ignore_status_mask = 0;
711 if (termios->c_iflag & IGNPAR)
712 up->port.ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
713 if (termios->c_iflag & IGNBRK) {
714 up->port.ignore_status_mask |= TXX9_SIDISR_UBRK;
715 /*
716 * If we're ignoring parity and break indicators,
717 * ignore overruns too (for real raw support).
718 */
719 if (termios->c_iflag & IGNPAR)
720 up->port.ignore_status_mask |= TXX9_SIDISR_UOER;
721 }
722
723 /*
724 * ignore all characters if CREAD is not set
725 */
726 if ((termios->c_cflag & CREAD) == 0)
727 up->port.ignore_status_mask |= TXX9_SIDISR_RDIS;
728
729 /* CTS flow control flag */
730 if ((termios->c_cflag & CRTSCTS) &&
731 (up->port.flags & UPF_TXX9_HAVE_CTS_LINE)) {
732 sio_set(up, TXX9_SIFLCR,
733 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
734 } else {
735 sio_mask(up, TXX9_SIFLCR,
736 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
737 }
738
739 sio_out(up, TXX9_SILCR, cval);
740 sio_quot_set(up, quot);
741 sio_out(up, TXX9_SIFCR, fcr);
742
743 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
744 spin_unlock_irqrestore(&up->port.lock, flags);
745}
746
747static void
748serial_txx9_pm(struct uart_port *port, unsigned int state,
749 unsigned int oldstate)
750{
751 /*
752 * If oldstate was -1 this is called from
753 * uart_configure_port(). In this case do not initialize the
754 * port now, because the port was already initialized (for
755 * non-console port) or should not be initialized here (for
756 * console port). If we initialized the port here we lose
757 * serial console settings.
758 */
759 if (state == 0 && oldstate != -1)
760 serial_txx9_initialize(port);
761}
762
763static int serial_txx9_request_resource(struct uart_txx9_port *up)
764{
765 unsigned int size = TXX9_REGION_SIZE;
766 int ret = 0;
767
768 switch (up->port.iotype) {
769 default:
770 if (!up->port.mapbase)
771 break;
772
773 if (!request_mem_region(up->port.mapbase, size, "serial_txx9")) {
774 ret = -EBUSY;
775 break;
776 }
777
778 if (up->port.flags & UPF_IOREMAP) {
779 up->port.membase = ioremap(up->port.mapbase, size);
780 if (!up->port.membase) {
781 release_mem_region(up->port.mapbase, size);
782 ret = -ENOMEM;
783 }
784 }
785 break;
786
787 case UPIO_PORT:
788 if (!request_region(up->port.iobase, size, "serial_txx9"))
789 ret = -EBUSY;
790 break;
791 }
792 return ret;
793}
794
795static void serial_txx9_release_resource(struct uart_txx9_port *up)
796{
797 unsigned int size = TXX9_REGION_SIZE;
798
799 switch (up->port.iotype) {
800 default:
801 if (!up->port.mapbase)
802 break;
803
804 if (up->port.flags & UPF_IOREMAP) {
805 iounmap(up->port.membase);
806 up->port.membase = NULL;
807 }
808
809 release_mem_region(up->port.mapbase, size);
810 break;
811
812 case UPIO_PORT:
813 release_region(up->port.iobase, size);
814 break;
815 }
816}
817
818static void serial_txx9_release_port(struct uart_port *port)
819{
820 struct uart_txx9_port *up = to_uart_txx9_port(port);
821 serial_txx9_release_resource(up);
822}
823
824static int serial_txx9_request_port(struct uart_port *port)
825{
826 struct uart_txx9_port *up = to_uart_txx9_port(port);
827 return serial_txx9_request_resource(up);
828}
829
830static void serial_txx9_config_port(struct uart_port *port, int uflags)
831{
832 struct uart_txx9_port *up = to_uart_txx9_port(port);
833 int ret;
834
835 /*
836 * Find the region that we can probe for. This in turn
837 * tells us whether we can probe for the type of port.
838 */
839 ret = serial_txx9_request_resource(up);
840 if (ret < 0)
841 return;
842 port->type = PORT_TXX9;
843 up->port.fifosize = TXX9_SIO_TX_FIFO;
844
845#ifdef CONFIG_SERIAL_TXX9_CONSOLE
846 if (up->port.line == up->port.cons->index)
847 return;
848#endif
849 serial_txx9_initialize(port);
850}
851
852static const char *
853serial_txx9_type(struct uart_port *port)
854{
855 return "txx9";
856}
857
858static struct uart_ops serial_txx9_pops = {
859 .tx_empty = serial_txx9_tx_empty,
860 .set_mctrl = serial_txx9_set_mctrl,
861 .get_mctrl = serial_txx9_get_mctrl,
862 .stop_tx = serial_txx9_stop_tx,
863 .start_tx = serial_txx9_start_tx,
864 .stop_rx = serial_txx9_stop_rx,
865 .enable_ms = serial_txx9_enable_ms,
866 .break_ctl = serial_txx9_break_ctl,
867 .startup = serial_txx9_startup,
868 .shutdown = serial_txx9_shutdown,
869 .set_termios = serial_txx9_set_termios,
870 .pm = serial_txx9_pm,
871 .type = serial_txx9_type,
872 .release_port = serial_txx9_release_port,
873 .request_port = serial_txx9_request_port,
874 .config_port = serial_txx9_config_port,
875#ifdef CONFIG_CONSOLE_POLL
876 .poll_get_char = serial_txx9_get_poll_char,
877 .poll_put_char = serial_txx9_put_poll_char,
878#endif
879};
880
881static struct uart_txx9_port serial_txx9_ports[UART_NR];
882
883static void __init serial_txx9_register_ports(struct uart_driver *drv,
884 struct device *dev)
885{
886 int i;
887
888 for (i = 0; i < UART_NR; i++) {
889 struct uart_txx9_port *up = &serial_txx9_ports[i];
890
891 up->port.line = i;
892 up->port.ops = &serial_txx9_pops;
893 up->port.dev = dev;
894 if (up->port.iobase || up->port.mapbase)
895 uart_add_one_port(drv, &up->port);
896 }
897}
898
899#ifdef CONFIG_SERIAL_TXX9_CONSOLE
900
901static void serial_txx9_console_putchar(struct uart_port *port, int ch)
902{
903 struct uart_txx9_port *up = to_uart_txx9_port(port);
904
905 wait_for_xmitr(up);
906 sio_out(up, TXX9_SITFIFO, ch);
907}
908
909/*
910 * Print a string to the serial port trying not to disturb
911 * any possible real use of the port...
912 *
913 * The console_lock must be held when we get here.
914 */
915static void
916serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
917{
918 struct uart_txx9_port *up = &serial_txx9_ports[co->index];
919 unsigned int ier, flcr;
920
921 /*
922 * First save the UER then disable the interrupts
923 */
924 ier = sio_in(up, TXX9_SIDICR);
925 sio_out(up, TXX9_SIDICR, 0);
926 /*
927 * Disable flow-control if enabled (and unnecessary)
928 */
929 flcr = sio_in(up, TXX9_SIFLCR);
930 if (!(up->port.flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
931 sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
932
933 uart_console_write(&up->port, s, count, serial_txx9_console_putchar);
934
935 /*
936 * Finally, wait for transmitter to become empty
937 * and restore the IER
938 */
939 wait_for_xmitr(up);
940 sio_out(up, TXX9_SIFLCR, flcr);
941 sio_out(up, TXX9_SIDICR, ier);
942}
943
944static int __init serial_txx9_console_setup(struct console *co, char *options)
945{
946 struct uart_port *port;
947 struct uart_txx9_port *up;
948 int baud = 9600;
949 int bits = 8;
950 int parity = 'n';
951 int flow = 'n';
952
953 /*
954 * Check whether an invalid uart number has been specified, and
955 * if so, search for the first available port that does have
956 * console support.
957 */
958 if (co->index >= UART_NR)
959 co->index = 0;
960 up = &serial_txx9_ports[co->index];
961 port = &up->port;
962 if (!port->ops)
963 return -ENODEV;
964
965 serial_txx9_initialize(&up->port);
966
967 if (options)
968 uart_parse_options(options, &baud, &parity, &bits, &flow);
969
970 return uart_set_options(port, co, baud, parity, bits, flow);
971}
972
973static struct uart_driver serial_txx9_reg;
974static struct console serial_txx9_console = {
975 .name = TXX9_TTY_NAME,
976 .write = serial_txx9_console_write,
977 .device = uart_console_device,
978 .setup = serial_txx9_console_setup,
979 .flags = CON_PRINTBUFFER,
980 .index = -1,
981 .data = &serial_txx9_reg,
982};
983
984static int __init serial_txx9_console_init(void)
985{
986 register_console(&serial_txx9_console);
987 return 0;
988}
989console_initcall(serial_txx9_console_init);
990
991#define SERIAL_TXX9_CONSOLE &serial_txx9_console
992#else
993#define SERIAL_TXX9_CONSOLE NULL
994#endif
995
996static struct uart_driver serial_txx9_reg = {
997 .owner = THIS_MODULE,
998 .driver_name = "serial_txx9",
999 .dev_name = TXX9_TTY_NAME,
1000 .major = TXX9_TTY_MAJOR,
1001 .minor = TXX9_TTY_MINOR_START,
1002 .nr = UART_NR,
1003 .cons = SERIAL_TXX9_CONSOLE,
1004};
1005
1006int __init early_serial_txx9_setup(struct uart_port *port)
1007{
1008 if (port->line >= ARRAY_SIZE(serial_txx9_ports))
1009 return -ENODEV;
1010
1011 serial_txx9_ports[port->line].port = *port;
1012 serial_txx9_ports[port->line].port.ops = &serial_txx9_pops;
1013 serial_txx9_ports[port->line].port.flags |=
1014 UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
1015 return 0;
1016}
1017
1018static DEFINE_MUTEX(serial_txx9_mutex);
1019
1020/**
1021 * serial_txx9_register_port - register a serial port
1022 * @port: serial port template
1023 *
1024 * Configure the serial port specified by the request.
1025 *
1026 * The port is then probed and if necessary the IRQ is autodetected
1027 * If this fails an error is returned.
1028 *
1029 * On success the port is ready to use and the line number is returned.
1030 */
1031static int __devinit serial_txx9_register_port(struct uart_port *port)
1032{
1033 int i;
1034 struct uart_txx9_port *uart;
1035 int ret = -ENOSPC;
1036
1037 mutex_lock(&serial_txx9_mutex);
1038 for (i = 0; i < UART_NR; i++) {
1039 uart = &serial_txx9_ports[i];
1040 if (uart_match_port(&uart->port, port)) {
1041 uart_remove_one_port(&serial_txx9_reg, &uart->port);
1042 break;
1043 }
1044 }
1045 if (i == UART_NR) {
1046 /* Find unused port */
1047 for (i = 0; i < UART_NR; i++) {
1048 uart = &serial_txx9_ports[i];
1049 if (!(uart->port.iobase || uart->port.mapbase))
1050 break;
1051 }
1052 }
1053 if (i < UART_NR) {
1054 uart->port.iobase = port->iobase;
1055 uart->port.membase = port->membase;
1056 uart->port.irq = port->irq;
1057 uart->port.uartclk = port->uartclk;
1058 uart->port.iotype = port->iotype;
1059 uart->port.flags = port->flags
1060 | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
1061 uart->port.mapbase = port->mapbase;
1062 if (port->dev)
1063 uart->port.dev = port->dev;
1064 ret = uart_add_one_port(&serial_txx9_reg, &uart->port);
1065 if (ret == 0)
1066 ret = uart->port.line;
1067 }
1068 mutex_unlock(&serial_txx9_mutex);
1069 return ret;
1070}
1071
1072/**
1073 * serial_txx9_unregister_port - remove a txx9 serial port at runtime
1074 * @line: serial line number
1075 *
1076 * Remove one serial port. This may not be called from interrupt
1077 * context. We hand the port back to the our control.
1078 */
1079static void __devexit serial_txx9_unregister_port(int line)
1080{
1081 struct uart_txx9_port *uart = &serial_txx9_ports[line];
1082
1083 mutex_lock(&serial_txx9_mutex);
1084 uart_remove_one_port(&serial_txx9_reg, &uart->port);
1085 uart->port.flags = 0;
1086 uart->port.type = PORT_UNKNOWN;
1087 uart->port.iobase = 0;
1088 uart->port.mapbase = 0;
1089 uart->port.membase = NULL;
1090 uart->port.dev = NULL;
1091 mutex_unlock(&serial_txx9_mutex);
1092}
1093
1094/*
1095 * Register a set of serial devices attached to a platform device.
1096 */
1097static int __devinit serial_txx9_probe(struct platform_device *dev)
1098{
1099 struct uart_port *p = dev->dev.platform_data;
1100 struct uart_port port;
1101 int ret, i;
1102
1103 memset(&port, 0, sizeof(struct uart_port));
1104 for (i = 0; p && p->uartclk != 0; p++, i++) {
1105 port.iobase = p->iobase;
1106 port.membase = p->membase;
1107 port.irq = p->irq;
1108 port.uartclk = p->uartclk;
1109 port.iotype = p->iotype;
1110 port.flags = p->flags;
1111 port.mapbase = p->mapbase;
1112 port.dev = &dev->dev;
1113 ret = serial_txx9_register_port(&port);
1114 if (ret < 0) {
1115 dev_err(&dev->dev, "unable to register port at index %d "
1116 "(IO%lx MEM%llx IRQ%d): %d\n", i,
1117 p->iobase, (unsigned long long)p->mapbase,
1118 p->irq, ret);
1119 }
1120 }
1121 return 0;
1122}
1123
1124/*
1125 * Remove serial ports registered against a platform device.
1126 */
1127static int __devexit serial_txx9_remove(struct platform_device *dev)
1128{
1129 int i;
1130
1131 for (i = 0; i < UART_NR; i++) {
1132 struct uart_txx9_port *up = &serial_txx9_ports[i];
1133
1134 if (up->port.dev == &dev->dev)
1135 serial_txx9_unregister_port(i);
1136 }
1137 return 0;
1138}
1139
1140#ifdef CONFIG_PM
1141static int serial_txx9_suspend(struct platform_device *dev, pm_message_t state)
1142{
1143 int i;
1144
1145 for (i = 0; i < UART_NR; i++) {
1146 struct uart_txx9_port *up = &serial_txx9_ports[i];
1147
1148 if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
1149 uart_suspend_port(&serial_txx9_reg, &up->port);
1150 }
1151
1152 return 0;
1153}
1154
1155static int serial_txx9_resume(struct platform_device *dev)
1156{
1157 int i;
1158
1159 for (i = 0; i < UART_NR; i++) {
1160 struct uart_txx9_port *up = &serial_txx9_ports[i];
1161
1162 if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
1163 uart_resume_port(&serial_txx9_reg, &up->port);
1164 }
1165
1166 return 0;
1167}
1168#endif
1169
1170static struct platform_driver serial_txx9_plat_driver = {
1171 .probe = serial_txx9_probe,
1172 .remove = __devexit_p(serial_txx9_remove),
1173#ifdef CONFIG_PM
1174 .suspend = serial_txx9_suspend,
1175 .resume = serial_txx9_resume,
1176#endif
1177 .driver = {
1178 .name = "serial_txx9",
1179 .owner = THIS_MODULE,
1180 },
1181};
1182
1183#ifdef ENABLE_SERIAL_TXX9_PCI
1184/*
1185 * Probe one serial board. Unfortunately, there is no rhyme nor reason
1186 * to the arrangement of serial ports on a PCI card.
1187 */
1188static int __devinit
1189pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
1190{
1191 struct uart_port port;
1192 int line;
1193 int rc;
1194
1195 rc = pci_enable_device(dev);
1196 if (rc)
1197 return rc;
1198
1199 memset(&port, 0, sizeof(port));
1200 port.ops = &serial_txx9_pops;
1201 port.flags |= UPF_TXX9_HAVE_CTS_LINE;
1202 port.uartclk = 66670000;
1203 port.irq = dev->irq;
1204 port.iotype = UPIO_PORT;
1205 port.iobase = pci_resource_start(dev, 1);
1206 port.dev = &dev->dev;
1207 line = serial_txx9_register_port(&port);
1208 if (line < 0) {
1209 printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
1210 pci_disable_device(dev);
1211 return line;
1212 }
1213 pci_set_drvdata(dev, &serial_txx9_ports[line]);
1214
1215 return 0;
1216}
1217
1218static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev)
1219{
1220 struct uart_txx9_port *up = pci_get_drvdata(dev);
1221
1222 pci_set_drvdata(dev, NULL);
1223
1224 if (up) {
1225 serial_txx9_unregister_port(up->port.line);
1226 pci_disable_device(dev);
1227 }
1228}
1229
1230#ifdef CONFIG_PM
1231static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
1232{
1233 struct uart_txx9_port *up = pci_get_drvdata(dev);
1234
1235 if (up)
1236 uart_suspend_port(&serial_txx9_reg, &up->port);
1237 pci_save_state(dev);
1238 pci_set_power_state(dev, pci_choose_state(dev, state));
1239 return 0;
1240}
1241
1242static int pciserial_txx9_resume_one(struct pci_dev *dev)
1243{
1244 struct uart_txx9_port *up = pci_get_drvdata(dev);
1245
1246 pci_set_power_state(dev, PCI_D0);
1247 pci_restore_state(dev);
1248 if (up)
1249 uart_resume_port(&serial_txx9_reg, &up->port);
1250 return 0;
1251}
1252#endif
1253
1254static const struct pci_device_id serial_txx9_pci_tbl[] = {
1255 { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC) },
1256 { 0, }
1257};
1258
1259static struct pci_driver serial_txx9_pci_driver = {
1260 .name = "serial_txx9",
1261 .probe = pciserial_txx9_init_one,
1262 .remove = __devexit_p(pciserial_txx9_remove_one),
1263#ifdef CONFIG_PM
1264 .suspend = pciserial_txx9_suspend_one,
1265 .resume = pciserial_txx9_resume_one,
1266#endif
1267 .id_table = serial_txx9_pci_tbl,
1268};
1269
1270MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
1271#endif /* ENABLE_SERIAL_TXX9_PCI */
1272
1273static struct platform_device *serial_txx9_plat_devs;
1274
1275static int __init serial_txx9_init(void)
1276{
1277 int ret;
1278
1279 printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
1280
1281 ret = uart_register_driver(&serial_txx9_reg);
1282 if (ret)
1283 goto out;
1284
1285 serial_txx9_plat_devs = platform_device_alloc("serial_txx9", -1);
1286 if (!serial_txx9_plat_devs) {
1287 ret = -ENOMEM;
1288 goto unreg_uart_drv;
1289 }
1290
1291 ret = platform_device_add(serial_txx9_plat_devs);
1292 if (ret)
1293 goto put_dev;
1294
1295 serial_txx9_register_ports(&serial_txx9_reg,
1296 &serial_txx9_plat_devs->dev);
1297
1298 ret = platform_driver_register(&serial_txx9_plat_driver);
1299 if (ret)
1300 goto del_dev;
1301
1302#ifdef ENABLE_SERIAL_TXX9_PCI
1303 ret = pci_register_driver(&serial_txx9_pci_driver);
1304#endif
1305 if (ret == 0)
1306 goto out;
1307
1308 del_dev:
1309 platform_device_del(serial_txx9_plat_devs);
1310 put_dev:
1311 platform_device_put(serial_txx9_plat_devs);
1312 unreg_uart_drv:
1313 uart_unregister_driver(&serial_txx9_reg);
1314 out:
1315 return ret;
1316}
1317
1318static void __exit serial_txx9_exit(void)
1319{
1320 int i;
1321
1322#ifdef ENABLE_SERIAL_TXX9_PCI
1323 pci_unregister_driver(&serial_txx9_pci_driver);
1324#endif
1325 platform_driver_unregister(&serial_txx9_plat_driver);
1326 platform_device_unregister(serial_txx9_plat_devs);
1327 for (i = 0; i < UART_NR; i++) {
1328 struct uart_txx9_port *up = &serial_txx9_ports[i];
1329 if (up->port.iobase || up->port.mapbase)
1330 uart_remove_one_port(&serial_txx9_reg, &up->port);
1331 }
1332
1333 uart_unregister_driver(&serial_txx9_reg);
1334}
1335
1336module_init(serial_txx9_init);
1337module_exit(serial_txx9_exit);
1338
1339MODULE_LICENSE("GPL");
1340MODULE_DESCRIPTION("TX39/49 serial driver");
1341
1342MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);