Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Atmel MultiMedia Card Interface driver
4 *
5 * Copyright (C) 2004-2008 Atmel Corporation
6 */
7#include <linux/blkdev.h>
8#include <linux/clk.h>
9#include <linux/debugfs.h>
10#include <linux/device.h>
11#include <linux/dmaengine.h>
12#include <linux/dma-mapping.h>
13#include <linux/err.h>
14#include <linux/gpio.h>
15#include <linux/init.h>
16#include <linux/interrupt.h>
17#include <linux/io.h>
18#include <linux/ioport.h>
19#include <linux/module.h>
20#include <linux/of.h>
21#include <linux/of_device.h>
22#include <linux/of_gpio.h>
23#include <linux/platform_device.h>
24#include <linux/scatterlist.h>
25#include <linux/seq_file.h>
26#include <linux/slab.h>
27#include <linux/stat.h>
28#include <linux/types.h>
29
30#include <linux/mmc/host.h>
31#include <linux/mmc/sdio.h>
32
33#include <linux/atmel-mci.h>
34#include <linux/atmel_pdc.h>
35#include <linux/pm.h>
36#include <linux/pm_runtime.h>
37#include <linux/pinctrl/consumer.h>
38
39#include <asm/cacheflush.h>
40#include <asm/io.h>
41#include <asm/unaligned.h>
42
43/*
44 * Superset of MCI IP registers integrated in Atmel AT91 Processor
45 * Registers and bitfields marked with [2] are only available in MCI2
46 */
47
48/* MCI Register Definitions */
49#define ATMCI_CR 0x0000 /* Control */
50#define ATMCI_CR_MCIEN BIT(0) /* MCI Enable */
51#define ATMCI_CR_MCIDIS BIT(1) /* MCI Disable */
52#define ATMCI_CR_PWSEN BIT(2) /* Power Save Enable */
53#define ATMCI_CR_PWSDIS BIT(3) /* Power Save Disable */
54#define ATMCI_CR_SWRST BIT(7) /* Software Reset */
55#define ATMCI_MR 0x0004 /* Mode */
56#define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
57#define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
58#define ATMCI_MR_RDPROOF BIT(11) /* Read Proof */
59#define ATMCI_MR_WRPROOF BIT(12) /* Write Proof */
60#define ATMCI_MR_PDCFBYTE BIT(13) /* Force Byte Transfer */
61#define ATMCI_MR_PDCPADV BIT(14) /* Padding Value */
62#define ATMCI_MR_PDCMODE BIT(15) /* PDC-oriented Mode */
63#define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
64#define ATMCI_DTOR 0x0008 /* Data Timeout */
65#define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
66#define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
67#define ATMCI_SDCR 0x000c /* SD Card / SDIO */
68#define ATMCI_SDCSEL_SLOT_A (0 << 0) /* Select SD slot A */
69#define ATMCI_SDCSEL_SLOT_B (1 << 0) /* Select SD slot A */
70#define ATMCI_SDCSEL_MASK (3 << 0)
71#define ATMCI_SDCBUS_1BIT (0 << 6) /* 1-bit data bus */
72#define ATMCI_SDCBUS_4BIT (2 << 6) /* 4-bit data bus */
73#define ATMCI_SDCBUS_8BIT (3 << 6) /* 8-bit data bus[2] */
74#define ATMCI_SDCBUS_MASK (3 << 6)
75#define ATMCI_ARGR 0x0010 /* Command Argument */
76#define ATMCI_CMDR 0x0014 /* Command */
77#define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
78#define ATMCI_CMDR_RSPTYP_NONE (0 << 6) /* No response */
79#define ATMCI_CMDR_RSPTYP_48BIT (1 << 6) /* 48-bit response */
80#define ATMCI_CMDR_RSPTYP_136BIT (2 << 6) /* 136-bit response */
81#define ATMCI_CMDR_SPCMD_INIT (1 << 8) /* Initialization command */
82#define ATMCI_CMDR_SPCMD_SYNC (2 << 8) /* Synchronized command */
83#define ATMCI_CMDR_SPCMD_INT (4 << 8) /* Interrupt command */
84#define ATMCI_CMDR_SPCMD_INTRESP (5 << 8) /* Interrupt response */
85#define ATMCI_CMDR_OPDCMD (1 << 11) /* Open Drain */
86#define ATMCI_CMDR_MAXLAT_5CYC (0 << 12) /* Max latency 5 cycles */
87#define ATMCI_CMDR_MAXLAT_64CYC (1 << 12) /* Max latency 64 cycles */
88#define ATMCI_CMDR_START_XFER (1 << 16) /* Start data transfer */
89#define ATMCI_CMDR_STOP_XFER (2 << 16) /* Stop data transfer */
90#define ATMCI_CMDR_TRDIR_WRITE (0 << 18) /* Write data */
91#define ATMCI_CMDR_TRDIR_READ (1 << 18) /* Read data */
92#define ATMCI_CMDR_BLOCK (0 << 19) /* Single-block transfer */
93#define ATMCI_CMDR_MULTI_BLOCK (1 << 19) /* Multi-block transfer */
94#define ATMCI_CMDR_STREAM (2 << 19) /* MMC Stream transfer */
95#define ATMCI_CMDR_SDIO_BYTE (4 << 19) /* SDIO Byte transfer */
96#define ATMCI_CMDR_SDIO_BLOCK (5 << 19) /* SDIO Block transfer */
97#define ATMCI_CMDR_SDIO_SUSPEND (1 << 24) /* SDIO Suspend Command */
98#define ATMCI_CMDR_SDIO_RESUME (2 << 24) /* SDIO Resume Command */
99#define ATMCI_BLKR 0x0018 /* Block */
100#define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
101#define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
102#define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
103#define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
104#define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
105#define ATMCI_RSPR 0x0020 /* Response 0 */
106#define ATMCI_RSPR1 0x0024 /* Response 1 */
107#define ATMCI_RSPR2 0x0028 /* Response 2 */
108#define ATMCI_RSPR3 0x002c /* Response 3 */
109#define ATMCI_RDR 0x0030 /* Receive Data */
110#define ATMCI_TDR 0x0034 /* Transmit Data */
111#define ATMCI_SR 0x0040 /* Status */
112#define ATMCI_IER 0x0044 /* Interrupt Enable */
113#define ATMCI_IDR 0x0048 /* Interrupt Disable */
114#define ATMCI_IMR 0x004c /* Interrupt Mask */
115#define ATMCI_CMDRDY BIT(0) /* Command Ready */
116#define ATMCI_RXRDY BIT(1) /* Receiver Ready */
117#define ATMCI_TXRDY BIT(2) /* Transmitter Ready */
118#define ATMCI_BLKE BIT(3) /* Data Block Ended */
119#define ATMCI_DTIP BIT(4) /* Data Transfer In Progress */
120#define ATMCI_NOTBUSY BIT(5) /* Data Not Busy */
121#define ATMCI_ENDRX BIT(6) /* End of RX Buffer */
122#define ATMCI_ENDTX BIT(7) /* End of TX Buffer */
123#define ATMCI_SDIOIRQA BIT(8) /* SDIO IRQ in slot A */
124#define ATMCI_SDIOIRQB BIT(9) /* SDIO IRQ in slot B */
125#define ATMCI_SDIOWAIT BIT(12) /* SDIO Read Wait Operation Status */
126#define ATMCI_CSRCV BIT(13) /* CE-ATA Completion Signal Received */
127#define ATMCI_RXBUFF BIT(14) /* RX Buffer Full */
128#define ATMCI_TXBUFE BIT(15) /* TX Buffer Empty */
129#define ATMCI_RINDE BIT(16) /* Response Index Error */
130#define ATMCI_RDIRE BIT(17) /* Response Direction Error */
131#define ATMCI_RCRCE BIT(18) /* Response CRC Error */
132#define ATMCI_RENDE BIT(19) /* Response End Bit Error */
133#define ATMCI_RTOE BIT(20) /* Response Time-Out Error */
134#define ATMCI_DCRCE BIT(21) /* Data CRC Error */
135#define ATMCI_DTOE BIT(22) /* Data Time-Out Error */
136#define ATMCI_CSTOE BIT(23) /* Completion Signal Time-out Error */
137#define ATMCI_BLKOVRE BIT(24) /* DMA Block Overrun Error */
138#define ATMCI_DMADONE BIT(25) /* DMA Transfer Done */
139#define ATMCI_FIFOEMPTY BIT(26) /* FIFO Empty Flag */
140#define ATMCI_XFRDONE BIT(27) /* Transfer Done Flag */
141#define ATMCI_ACKRCV BIT(28) /* Boot Operation Acknowledge Received */
142#define ATMCI_ACKRCVE BIT(29) /* Boot Operation Acknowledge Error */
143#define ATMCI_OVRE BIT(30) /* RX Overrun Error */
144#define ATMCI_UNRE BIT(31) /* TX Underrun Error */
145#define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
146#define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
147#define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
148#define ATMCI_DMAEN BIT(8) /* DMA Hardware Handshaking Enable */
149#define ATMCI_CFG 0x0054 /* Configuration[2] */
150#define ATMCI_CFG_FIFOMODE_1DATA BIT(0) /* MCI Internal FIFO control mode */
151#define ATMCI_CFG_FERRCTRL_COR BIT(4) /* Flow Error flag reset control mode */
152#define ATMCI_CFG_HSMODE BIT(8) /* High Speed Mode */
153#define ATMCI_CFG_LSYNC BIT(12) /* Synchronize on the last block */
154#define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
155#define ATMCI_WP_EN BIT(0) /* WP Enable */
156#define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
157#define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
158#define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
159#define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
160#define ATMCI_VERSION 0x00FC /* Version */
161#define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
162
163/* This is not including the FIFO Aperture on MCI2 */
164#define ATMCI_REGS_SIZE 0x100
165
166/* Register access macros */
167#define atmci_readl(port, reg) \
168 __raw_readl((port)->regs + reg)
169#define atmci_writel(port, reg, value) \
170 __raw_writel((value), (port)->regs + reg)
171
172#define ATMCI_CMD_TIMEOUT_MS 2000
173#define AUTOSUSPEND_DELAY 50
174
175#define ATMCI_DATA_ERROR_FLAGS (ATMCI_DCRCE | ATMCI_DTOE | ATMCI_OVRE | ATMCI_UNRE)
176#define ATMCI_DMA_THRESHOLD 16
177
178enum {
179 EVENT_CMD_RDY = 0,
180 EVENT_XFER_COMPLETE,
181 EVENT_NOTBUSY,
182 EVENT_DATA_ERROR,
183};
184
185enum atmel_mci_state {
186 STATE_IDLE = 0,
187 STATE_SENDING_CMD,
188 STATE_DATA_XFER,
189 STATE_WAITING_NOTBUSY,
190 STATE_SENDING_STOP,
191 STATE_END_REQUEST,
192};
193
194enum atmci_xfer_dir {
195 XFER_RECEIVE = 0,
196 XFER_TRANSMIT,
197};
198
199enum atmci_pdc_buf {
200 PDC_FIRST_BUF = 0,
201 PDC_SECOND_BUF,
202};
203
204struct atmel_mci_caps {
205 bool has_dma_conf_reg;
206 bool has_pdc;
207 bool has_cfg_reg;
208 bool has_cstor_reg;
209 bool has_highspeed;
210 bool has_rwproof;
211 bool has_odd_clk_div;
212 bool has_bad_data_ordering;
213 bool need_reset_after_xfer;
214 bool need_blksz_mul_4;
215 bool need_notbusy_for_read_ops;
216};
217
218struct atmel_mci_dma {
219 struct dma_chan *chan;
220 struct dma_async_tx_descriptor *data_desc;
221};
222
223/**
224 * struct atmel_mci - MMC controller state shared between all slots
225 * @lock: Spinlock protecting the queue and associated data.
226 * @regs: Pointer to MMIO registers.
227 * @sg: Scatterlist entry currently being processed by PIO or PDC code.
228 * @sg_len: Size of the scatterlist
229 * @pio_offset: Offset into the current scatterlist entry.
230 * @buffer: Buffer used if we don't have the r/w proof capability. We
231 * don't have the time to switch pdc buffers so we have to use only
232 * one buffer for the full transaction.
233 * @buf_size: size of the buffer.
234 * @buf_phys_addr: buffer address needed for pdc.
235 * @cur_slot: The slot which is currently using the controller.
236 * @mrq: The request currently being processed on @cur_slot,
237 * or NULL if the controller is idle.
238 * @cmd: The command currently being sent to the card, or NULL.
239 * @data: The data currently being transferred, or NULL if no data
240 * transfer is in progress.
241 * @data_size: just data->blocks * data->blksz.
242 * @dma: DMA client state.
243 * @data_chan: DMA channel being used for the current data transfer.
244 * @dma_conf: Configuration for the DMA slave
245 * @cmd_status: Snapshot of SR taken upon completion of the current
246 * command. Only valid when EVENT_CMD_COMPLETE is pending.
247 * @data_status: Snapshot of SR taken upon completion of the current
248 * data transfer. Only valid when EVENT_DATA_COMPLETE or
249 * EVENT_DATA_ERROR is pending.
250 * @stop_cmdr: Value to be loaded into CMDR when the stop command is
251 * to be sent.
252 * @tasklet: Tasklet running the request state machine.
253 * @pending_events: Bitmask of events flagged by the interrupt handler
254 * to be processed by the tasklet.
255 * @completed_events: Bitmask of events which the state machine has
256 * processed.
257 * @state: Tasklet state.
258 * @queue: List of slots waiting for access to the controller.
259 * @need_clock_update: Update the clock rate before the next request.
260 * @need_reset: Reset controller before next request.
261 * @timer: Timer to balance the data timeout error flag which cannot rise.
262 * @mode_reg: Value of the MR register.
263 * @cfg_reg: Value of the CFG register.
264 * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
265 * rate and timeout calculations.
266 * @mapbase: Physical address of the MMIO registers.
267 * @mck: The peripheral bus clock hooked up to the MMC controller.
268 * @pdev: Platform device associated with the MMC controller.
269 * @slot: Slots sharing this MMC controller.
270 * @caps: MCI capabilities depending on MCI version.
271 * @prepare_data: function to setup MCI before data transfer which
272 * depends on MCI capabilities.
273 * @submit_data: function to start data transfer which depends on MCI
274 * capabilities.
275 * @stop_transfer: function to stop data transfer which depends on MCI
276 * capabilities.
277 *
278 * Locking
279 * =======
280 *
281 * @lock is a softirq-safe spinlock protecting @queue as well as
282 * @cur_slot, @mrq and @state. These must always be updated
283 * at the same time while holding @lock.
284 *
285 * @lock also protects mode_reg and need_clock_update since these are
286 * used to synchronize mode register updates with the queue
287 * processing.
288 *
289 * The @mrq field of struct atmel_mci_slot is also protected by @lock,
290 * and must always be written at the same time as the slot is added to
291 * @queue.
292 *
293 * @pending_events and @completed_events are accessed using atomic bit
294 * operations, so they don't need any locking.
295 *
296 * None of the fields touched by the interrupt handler need any
297 * locking. However, ordering is important: Before EVENT_DATA_ERROR or
298 * EVENT_DATA_COMPLETE is set in @pending_events, all data-related
299 * interrupts must be disabled and @data_status updated with a
300 * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the
301 * CMDRDY interrupt must be disabled and @cmd_status updated with a
302 * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the
303 * bytes_xfered field of @data must be written. This is ensured by
304 * using barriers.
305 */
306struct atmel_mci {
307 spinlock_t lock;
308 void __iomem *regs;
309
310 struct scatterlist *sg;
311 unsigned int sg_len;
312 unsigned int pio_offset;
313 unsigned int *buffer;
314 unsigned int buf_size;
315 dma_addr_t buf_phys_addr;
316
317 struct atmel_mci_slot *cur_slot;
318 struct mmc_request *mrq;
319 struct mmc_command *cmd;
320 struct mmc_data *data;
321 unsigned int data_size;
322
323 struct atmel_mci_dma dma;
324 struct dma_chan *data_chan;
325 struct dma_slave_config dma_conf;
326
327 u32 cmd_status;
328 u32 data_status;
329 u32 stop_cmdr;
330
331 struct tasklet_struct tasklet;
332 unsigned long pending_events;
333 unsigned long completed_events;
334 enum atmel_mci_state state;
335 struct list_head queue;
336
337 bool need_clock_update;
338 bool need_reset;
339 struct timer_list timer;
340 u32 mode_reg;
341 u32 cfg_reg;
342 unsigned long bus_hz;
343 unsigned long mapbase;
344 struct clk *mck;
345 struct platform_device *pdev;
346
347 struct atmel_mci_slot *slot[ATMCI_MAX_NR_SLOTS];
348
349 struct atmel_mci_caps caps;
350
351 u32 (*prepare_data)(struct atmel_mci *host, struct mmc_data *data);
352 void (*submit_data)(struct atmel_mci *host, struct mmc_data *data);
353 void (*stop_transfer)(struct atmel_mci *host);
354};
355
356/**
357 * struct atmel_mci_slot - MMC slot state
358 * @mmc: The mmc_host representing this slot.
359 * @host: The MMC controller this slot is using.
360 * @sdc_reg: Value of SDCR to be written before using this slot.
361 * @sdio_irq: SDIO irq mask for this slot.
362 * @mrq: mmc_request currently being processed or waiting to be
363 * processed, or NULL when the slot is idle.
364 * @queue_node: List node for placing this node in the @queue list of
365 * &struct atmel_mci.
366 * @clock: Clock rate configured by set_ios(). Protected by host->lock.
367 * @flags: Random state bits associated with the slot.
368 * @detect_pin: GPIO pin used for card detection, or negative if not
369 * available.
370 * @wp_pin: GPIO pin used for card write protect sending, or negative
371 * if not available.
372 * @detect_is_active_high: The state of the detect pin when it is active.
373 * @detect_timer: Timer used for debouncing @detect_pin interrupts.
374 */
375struct atmel_mci_slot {
376 struct mmc_host *mmc;
377 struct atmel_mci *host;
378
379 u32 sdc_reg;
380 u32 sdio_irq;
381
382 struct mmc_request *mrq;
383 struct list_head queue_node;
384
385 unsigned int clock;
386 unsigned long flags;
387#define ATMCI_CARD_PRESENT 0
388#define ATMCI_CARD_NEED_INIT 1
389#define ATMCI_SHUTDOWN 2
390
391 int detect_pin;
392 int wp_pin;
393 bool detect_is_active_high;
394
395 struct timer_list detect_timer;
396};
397
398#define atmci_test_and_clear_pending(host, event) \
399 test_and_clear_bit(event, &host->pending_events)
400#define atmci_set_completed(host, event) \
401 set_bit(event, &host->completed_events)
402#define atmci_set_pending(host, event) \
403 set_bit(event, &host->pending_events)
404
405/*
406 * The debugfs stuff below is mostly optimized away when
407 * CONFIG_DEBUG_FS is not set.
408 */
409static int atmci_req_show(struct seq_file *s, void *v)
410{
411 struct atmel_mci_slot *slot = s->private;
412 struct mmc_request *mrq;
413 struct mmc_command *cmd;
414 struct mmc_command *stop;
415 struct mmc_data *data;
416
417 /* Make sure we get a consistent snapshot */
418 spin_lock_bh(&slot->host->lock);
419 mrq = slot->mrq;
420
421 if (mrq) {
422 cmd = mrq->cmd;
423 data = mrq->data;
424 stop = mrq->stop;
425
426 if (cmd)
427 seq_printf(s,
428 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
429 cmd->opcode, cmd->arg, cmd->flags,
430 cmd->resp[0], cmd->resp[1], cmd->resp[2],
431 cmd->resp[3], cmd->error);
432 if (data)
433 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
434 data->bytes_xfered, data->blocks,
435 data->blksz, data->flags, data->error);
436 if (stop)
437 seq_printf(s,
438 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
439 stop->opcode, stop->arg, stop->flags,
440 stop->resp[0], stop->resp[1], stop->resp[2],
441 stop->resp[3], stop->error);
442 }
443
444 spin_unlock_bh(&slot->host->lock);
445
446 return 0;
447}
448
449DEFINE_SHOW_ATTRIBUTE(atmci_req);
450
451static void atmci_show_status_reg(struct seq_file *s,
452 const char *regname, u32 value)
453{
454 static const char *sr_bit[] = {
455 [0] = "CMDRDY",
456 [1] = "RXRDY",
457 [2] = "TXRDY",
458 [3] = "BLKE",
459 [4] = "DTIP",
460 [5] = "NOTBUSY",
461 [6] = "ENDRX",
462 [7] = "ENDTX",
463 [8] = "SDIOIRQA",
464 [9] = "SDIOIRQB",
465 [12] = "SDIOWAIT",
466 [14] = "RXBUFF",
467 [15] = "TXBUFE",
468 [16] = "RINDE",
469 [17] = "RDIRE",
470 [18] = "RCRCE",
471 [19] = "RENDE",
472 [20] = "RTOE",
473 [21] = "DCRCE",
474 [22] = "DTOE",
475 [23] = "CSTOE",
476 [24] = "BLKOVRE",
477 [25] = "DMADONE",
478 [26] = "FIFOEMPTY",
479 [27] = "XFRDONE",
480 [30] = "OVRE",
481 [31] = "UNRE",
482 };
483 unsigned int i;
484
485 seq_printf(s, "%s:\t0x%08x", regname, value);
486 for (i = 0; i < ARRAY_SIZE(sr_bit); i++) {
487 if (value & (1 << i)) {
488 if (sr_bit[i])
489 seq_printf(s, " %s", sr_bit[i]);
490 else
491 seq_puts(s, " UNKNOWN");
492 }
493 }
494 seq_putc(s, '\n');
495}
496
497static int atmci_regs_show(struct seq_file *s, void *v)
498{
499 struct atmel_mci *host = s->private;
500 u32 *buf;
501 int ret = 0;
502
503
504 buf = kmalloc(ATMCI_REGS_SIZE, GFP_KERNEL);
505 if (!buf)
506 return -ENOMEM;
507
508 pm_runtime_get_sync(&host->pdev->dev);
509
510 /*
511 * Grab a more or less consistent snapshot. Note that we're
512 * not disabling interrupts, so IMR and SR may not be
513 * consistent.
514 */
515 spin_lock_bh(&host->lock);
516 memcpy_fromio(buf, host->regs, ATMCI_REGS_SIZE);
517 spin_unlock_bh(&host->lock);
518
519 pm_runtime_mark_last_busy(&host->pdev->dev);
520 pm_runtime_put_autosuspend(&host->pdev->dev);
521
522 seq_printf(s, "MR:\t0x%08x%s%s ",
523 buf[ATMCI_MR / 4],
524 buf[ATMCI_MR / 4] & ATMCI_MR_RDPROOF ? " RDPROOF" : "",
525 buf[ATMCI_MR / 4] & ATMCI_MR_WRPROOF ? " WRPROOF" : "");
526 if (host->caps.has_odd_clk_div)
527 seq_printf(s, "{CLKDIV,CLKODD}=%u\n",
528 ((buf[ATMCI_MR / 4] & 0xff) << 1)
529 | ((buf[ATMCI_MR / 4] >> 16) & 1));
530 else
531 seq_printf(s, "CLKDIV=%u\n",
532 (buf[ATMCI_MR / 4] & 0xff));
533 seq_printf(s, "DTOR:\t0x%08x\n", buf[ATMCI_DTOR / 4]);
534 seq_printf(s, "SDCR:\t0x%08x\n", buf[ATMCI_SDCR / 4]);
535 seq_printf(s, "ARGR:\t0x%08x\n", buf[ATMCI_ARGR / 4]);
536 seq_printf(s, "BLKR:\t0x%08x BCNT=%u BLKLEN=%u\n",
537 buf[ATMCI_BLKR / 4],
538 buf[ATMCI_BLKR / 4] & 0xffff,
539 (buf[ATMCI_BLKR / 4] >> 16) & 0xffff);
540 if (host->caps.has_cstor_reg)
541 seq_printf(s, "CSTOR:\t0x%08x\n", buf[ATMCI_CSTOR / 4]);
542
543 /* Don't read RSPR and RDR; it will consume the data there */
544
545 atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]);
546 atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]);
547
548 if (host->caps.has_dma_conf_reg) {
549 u32 val;
550
551 val = buf[ATMCI_DMA / 4];
552 seq_printf(s, "DMA:\t0x%08x OFFSET=%u CHKSIZE=%u%s\n",
553 val, val & 3,
554 ((val >> 4) & 3) ?
555 1 << (((val >> 4) & 3) + 1) : 1,
556 val & ATMCI_DMAEN ? " DMAEN" : "");
557 }
558 if (host->caps.has_cfg_reg) {
559 u32 val;
560
561 val = buf[ATMCI_CFG / 4];
562 seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n",
563 val,
564 val & ATMCI_CFG_FIFOMODE_1DATA ? " FIFOMODE_ONE_DATA" : "",
565 val & ATMCI_CFG_FERRCTRL_COR ? " FERRCTRL_CLEAR_ON_READ" : "",
566 val & ATMCI_CFG_HSMODE ? " HSMODE" : "",
567 val & ATMCI_CFG_LSYNC ? " LSYNC" : "");
568 }
569
570 kfree(buf);
571
572 return ret;
573}
574
575DEFINE_SHOW_ATTRIBUTE(atmci_regs);
576
577static void atmci_init_debugfs(struct atmel_mci_slot *slot)
578{
579 struct mmc_host *mmc = slot->mmc;
580 struct atmel_mci *host = slot->host;
581 struct dentry *root;
582
583 root = mmc->debugfs_root;
584 if (!root)
585 return;
586
587 debugfs_create_file("regs", S_IRUSR, root, host, &atmci_regs_fops);
588 debugfs_create_file("req", S_IRUSR, root, slot, &atmci_req_fops);
589 debugfs_create_u32("state", S_IRUSR, root, &host->state);
590 debugfs_create_xul("pending_events", S_IRUSR, root,
591 &host->pending_events);
592 debugfs_create_xul("completed_events", S_IRUSR, root,
593 &host->completed_events);
594}
595
596#if defined(CONFIG_OF)
597static const struct of_device_id atmci_dt_ids[] = {
598 { .compatible = "atmel,hsmci" },
599 { /* sentinel */ }
600};
601
602MODULE_DEVICE_TABLE(of, atmci_dt_ids);
603
604static struct mci_platform_data*
605atmci_of_init(struct platform_device *pdev)
606{
607 struct device_node *np = pdev->dev.of_node;
608 struct device_node *cnp;
609 struct mci_platform_data *pdata;
610 u32 slot_id;
611
612 if (!np) {
613 dev_err(&pdev->dev, "device node not found\n");
614 return ERR_PTR(-EINVAL);
615 }
616
617 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
618 if (!pdata)
619 return ERR_PTR(-ENOMEM);
620
621 for_each_child_of_node(np, cnp) {
622 if (of_property_read_u32(cnp, "reg", &slot_id)) {
623 dev_warn(&pdev->dev, "reg property is missing for %pOF\n",
624 cnp);
625 continue;
626 }
627
628 if (slot_id >= ATMCI_MAX_NR_SLOTS) {
629 dev_warn(&pdev->dev, "can't have more than %d slots\n",
630 ATMCI_MAX_NR_SLOTS);
631 of_node_put(cnp);
632 break;
633 }
634
635 if (of_property_read_u32(cnp, "bus-width",
636 &pdata->slot[slot_id].bus_width))
637 pdata->slot[slot_id].bus_width = 1;
638
639 pdata->slot[slot_id].detect_pin =
640 of_get_named_gpio(cnp, "cd-gpios", 0);
641
642 pdata->slot[slot_id].detect_is_active_high =
643 of_property_read_bool(cnp, "cd-inverted");
644
645 pdata->slot[slot_id].non_removable =
646 of_property_read_bool(cnp, "non-removable");
647
648 pdata->slot[slot_id].wp_pin =
649 of_get_named_gpio(cnp, "wp-gpios", 0);
650 }
651
652 return pdata;
653}
654#else /* CONFIG_OF */
655static inline struct mci_platform_data*
656atmci_of_init(struct platform_device *dev)
657{
658 return ERR_PTR(-EINVAL);
659}
660#endif
661
662static inline unsigned int atmci_get_version(struct atmel_mci *host)
663{
664 return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
665}
666
667/*
668 * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
669 * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
670 * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
671 * 8 -> 3, 16 -> 4.
672 *
673 * This can be done by finding most significant bit set.
674 */
675static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
676 unsigned int maxburst)
677{
678 unsigned int version = atmci_get_version(host);
679 unsigned int offset = 2;
680
681 if (version >= 0x600)
682 offset = 1;
683
684 if (maxburst > 1)
685 return fls(maxburst) - offset;
686 else
687 return 0;
688}
689
690static void atmci_timeout_timer(struct timer_list *t)
691{
692 struct atmel_mci *host;
693
694 host = from_timer(host, t, timer);
695
696 dev_dbg(&host->pdev->dev, "software timeout\n");
697
698 if (host->mrq->cmd->data) {
699 host->mrq->cmd->data->error = -ETIMEDOUT;
700 host->data = NULL;
701 /*
702 * With some SDIO modules, sometimes DMA transfer hangs. If
703 * stop_transfer() is not called then the DMA request is not
704 * removed, following ones are queued and never computed.
705 */
706 if (host->state == STATE_DATA_XFER)
707 host->stop_transfer(host);
708 } else {
709 host->mrq->cmd->error = -ETIMEDOUT;
710 host->cmd = NULL;
711 }
712 host->need_reset = 1;
713 host->state = STATE_END_REQUEST;
714 smp_wmb();
715 tasklet_schedule(&host->tasklet);
716}
717
718static inline unsigned int atmci_ns_to_clocks(struct atmel_mci *host,
719 unsigned int ns)
720{
721 /*
722 * It is easier here to use us instead of ns for the timeout,
723 * it prevents from overflows during calculation.
724 */
725 unsigned int us = DIV_ROUND_UP(ns, 1000);
726
727 /* Maximum clock frequency is host->bus_hz/2 */
728 return us * (DIV_ROUND_UP(host->bus_hz, 2000000));
729}
730
731static void atmci_set_timeout(struct atmel_mci *host,
732 struct atmel_mci_slot *slot, struct mmc_data *data)
733{
734 static unsigned dtomul_to_shift[] = {
735 0, 4, 7, 8, 10, 12, 16, 20
736 };
737 unsigned timeout;
738 unsigned dtocyc;
739 unsigned dtomul;
740
741 timeout = atmci_ns_to_clocks(host, data->timeout_ns)
742 + data->timeout_clks;
743
744 for (dtomul = 0; dtomul < 8; dtomul++) {
745 unsigned shift = dtomul_to_shift[dtomul];
746 dtocyc = (timeout + (1 << shift) - 1) >> shift;
747 if (dtocyc < 15)
748 break;
749 }
750
751 if (dtomul >= 8) {
752 dtomul = 7;
753 dtocyc = 15;
754 }
755
756 dev_vdbg(&slot->mmc->class_dev, "setting timeout to %u cycles\n",
757 dtocyc << dtomul_to_shift[dtomul]);
758 atmci_writel(host, ATMCI_DTOR, (ATMCI_DTOMUL(dtomul) | ATMCI_DTOCYC(dtocyc)));
759}
760
761/*
762 * Return mask with command flags to be enabled for this command.
763 */
764static u32 atmci_prepare_command(struct mmc_host *mmc,
765 struct mmc_command *cmd)
766{
767 struct mmc_data *data;
768 u32 cmdr;
769
770 cmd->error = -EINPROGRESS;
771
772 cmdr = ATMCI_CMDR_CMDNB(cmd->opcode);
773
774 if (cmd->flags & MMC_RSP_PRESENT) {
775 if (cmd->flags & MMC_RSP_136)
776 cmdr |= ATMCI_CMDR_RSPTYP_136BIT;
777 else
778 cmdr |= ATMCI_CMDR_RSPTYP_48BIT;
779 }
780
781 /*
782 * This should really be MAXLAT_5 for CMD2 and ACMD41, but
783 * it's too difficult to determine whether this is an ACMD or
784 * not. Better make it 64.
785 */
786 cmdr |= ATMCI_CMDR_MAXLAT_64CYC;
787
788 if (mmc->ios.bus_mode == MMC_BUSMODE_OPENDRAIN)
789 cmdr |= ATMCI_CMDR_OPDCMD;
790
791 data = cmd->data;
792 if (data) {
793 cmdr |= ATMCI_CMDR_START_XFER;
794
795 if (cmd->opcode == SD_IO_RW_EXTENDED) {
796 cmdr |= ATMCI_CMDR_SDIO_BLOCK;
797 } else {
798 if (data->blocks > 1)
799 cmdr |= ATMCI_CMDR_MULTI_BLOCK;
800 else
801 cmdr |= ATMCI_CMDR_BLOCK;
802 }
803
804 if (data->flags & MMC_DATA_READ)
805 cmdr |= ATMCI_CMDR_TRDIR_READ;
806 }
807
808 return cmdr;
809}
810
811static void atmci_send_command(struct atmel_mci *host,
812 struct mmc_command *cmd, u32 cmd_flags)
813{
814 unsigned int timeout_ms = cmd->busy_timeout ? cmd->busy_timeout :
815 ATMCI_CMD_TIMEOUT_MS;
816
817 WARN_ON(host->cmd);
818 host->cmd = cmd;
819
820 dev_vdbg(&host->pdev->dev,
821 "start command: ARGR=0x%08x CMDR=0x%08x\n",
822 cmd->arg, cmd_flags);
823
824 atmci_writel(host, ATMCI_ARGR, cmd->arg);
825 atmci_writel(host, ATMCI_CMDR, cmd_flags);
826
827 mod_timer(&host->timer, jiffies + msecs_to_jiffies(timeout_ms));
828}
829
830static void atmci_send_stop_cmd(struct atmel_mci *host, struct mmc_data *data)
831{
832 dev_dbg(&host->pdev->dev, "send stop command\n");
833 atmci_send_command(host, data->stop, host->stop_cmdr);
834 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
835}
836
837/*
838 * Configure given PDC buffer taking care of alignement issues.
839 * Update host->data_size and host->sg.
840 */
841static void atmci_pdc_set_single_buf(struct atmel_mci *host,
842 enum atmci_xfer_dir dir, enum atmci_pdc_buf buf_nb)
843{
844 u32 pointer_reg, counter_reg;
845 unsigned int buf_size;
846
847 if (dir == XFER_RECEIVE) {
848 pointer_reg = ATMEL_PDC_RPR;
849 counter_reg = ATMEL_PDC_RCR;
850 } else {
851 pointer_reg = ATMEL_PDC_TPR;
852 counter_reg = ATMEL_PDC_TCR;
853 }
854
855 if (buf_nb == PDC_SECOND_BUF) {
856 pointer_reg += ATMEL_PDC_SCND_BUF_OFF;
857 counter_reg += ATMEL_PDC_SCND_BUF_OFF;
858 }
859
860 if (!host->caps.has_rwproof) {
861 buf_size = host->buf_size;
862 atmci_writel(host, pointer_reg, host->buf_phys_addr);
863 } else {
864 buf_size = sg_dma_len(host->sg);
865 atmci_writel(host, pointer_reg, sg_dma_address(host->sg));
866 }
867
868 if (host->data_size <= buf_size) {
869 if (host->data_size & 0x3) {
870 /* If size is different from modulo 4, transfer bytes */
871 atmci_writel(host, counter_reg, host->data_size);
872 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCFBYTE);
873 } else {
874 /* Else transfer 32-bits words */
875 atmci_writel(host, counter_reg, host->data_size / 4);
876 }
877 host->data_size = 0;
878 } else {
879 /* We assume the size of a page is 32-bits aligned */
880 atmci_writel(host, counter_reg, sg_dma_len(host->sg) / 4);
881 host->data_size -= sg_dma_len(host->sg);
882 if (host->data_size)
883 host->sg = sg_next(host->sg);
884 }
885}
886
887/*
888 * Configure PDC buffer according to the data size ie configuring one or two
889 * buffers. Don't use this function if you want to configure only the second
890 * buffer. In this case, use atmci_pdc_set_single_buf.
891 */
892static void atmci_pdc_set_both_buf(struct atmel_mci *host, int dir)
893{
894 atmci_pdc_set_single_buf(host, dir, PDC_FIRST_BUF);
895 if (host->data_size)
896 atmci_pdc_set_single_buf(host, dir, PDC_SECOND_BUF);
897}
898
899/*
900 * Unmap sg lists, called when transfer is finished.
901 */
902static void atmci_pdc_cleanup(struct atmel_mci *host)
903{
904 struct mmc_data *data = host->data;
905
906 if (data)
907 dma_unmap_sg(&host->pdev->dev,
908 data->sg, data->sg_len,
909 mmc_get_dma_dir(data));
910}
911
912/*
913 * Disable PDC transfers. Update pending flags to EVENT_XFER_COMPLETE after
914 * having received ATMCI_TXBUFE or ATMCI_RXBUFF interrupt. Enable ATMCI_NOTBUSY
915 * interrupt needed for both transfer directions.
916 */
917static void atmci_pdc_complete(struct atmel_mci *host)
918{
919 int transfer_size = host->data->blocks * host->data->blksz;
920 int i;
921
922 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
923
924 if ((!host->caps.has_rwproof)
925 && (host->data->flags & MMC_DATA_READ)) {
926 if (host->caps.has_bad_data_ordering)
927 for (i = 0; i < transfer_size; i++)
928 host->buffer[i] = swab32(host->buffer[i]);
929 sg_copy_from_buffer(host->data->sg, host->data->sg_len,
930 host->buffer, transfer_size);
931 }
932
933 atmci_pdc_cleanup(host);
934
935 dev_dbg(&host->pdev->dev, "(%s) set pending xfer complete\n", __func__);
936 atmci_set_pending(host, EVENT_XFER_COMPLETE);
937 tasklet_schedule(&host->tasklet);
938}
939
940static void atmci_dma_cleanup(struct atmel_mci *host)
941{
942 struct mmc_data *data = host->data;
943
944 if (data)
945 dma_unmap_sg(host->dma.chan->device->dev,
946 data->sg, data->sg_len,
947 mmc_get_dma_dir(data));
948}
949
950/*
951 * This function is called by the DMA driver from tasklet context.
952 */
953static void atmci_dma_complete(void *arg)
954{
955 struct atmel_mci *host = arg;
956 struct mmc_data *data = host->data;
957
958 dev_vdbg(&host->pdev->dev, "DMA complete\n");
959
960 if (host->caps.has_dma_conf_reg)
961 /* Disable DMA hardware handshaking on MCI */
962 atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN);
963
964 atmci_dma_cleanup(host);
965
966 /*
967 * If the card was removed, data will be NULL. No point trying
968 * to send the stop command or waiting for NBUSY in this case.
969 */
970 if (data) {
971 dev_dbg(&host->pdev->dev,
972 "(%s) set pending xfer complete\n", __func__);
973 atmci_set_pending(host, EVENT_XFER_COMPLETE);
974 tasklet_schedule(&host->tasklet);
975
976 /*
977 * Regardless of what the documentation says, we have
978 * to wait for NOTBUSY even after block read
979 * operations.
980 *
981 * When the DMA transfer is complete, the controller
982 * may still be reading the CRC from the card, i.e.
983 * the data transfer is still in progress and we
984 * haven't seen all the potential error bits yet.
985 *
986 * The interrupt handler will schedule a different
987 * tasklet to finish things up when the data transfer
988 * is completely done.
989 *
990 * We may not complete the mmc request here anyway
991 * because the mmc layer may call back and cause us to
992 * violate the "don't submit new operations from the
993 * completion callback" rule of the dma engine
994 * framework.
995 */
996 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
997 }
998}
999
1000/*
1001 * Returns a mask of interrupt flags to be enabled after the whole
1002 * request has been prepared.
1003 */
1004static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
1005{
1006 u32 iflags;
1007
1008 data->error = -EINPROGRESS;
1009
1010 host->sg = data->sg;
1011 host->sg_len = data->sg_len;
1012 host->data = data;
1013 host->data_chan = NULL;
1014
1015 iflags = ATMCI_DATA_ERROR_FLAGS;
1016
1017 /*
1018 * Errata: MMC data write operation with less than 12
1019 * bytes is impossible.
1020 *
1021 * Errata: MCI Transmit Data Register (TDR) FIFO
1022 * corruption when length is not multiple of 4.
1023 */
1024 if (data->blocks * data->blksz < 12
1025 || (data->blocks * data->blksz) & 3)
1026 host->need_reset = true;
1027
1028 host->pio_offset = 0;
1029 if (data->flags & MMC_DATA_READ)
1030 iflags |= ATMCI_RXRDY;
1031 else
1032 iflags |= ATMCI_TXRDY;
1033
1034 return iflags;
1035}
1036
1037/*
1038 * Set interrupt flags and set block length into the MCI mode register even
1039 * if this value is also accessible in the MCI block register. It seems to be
1040 * necessary before the High Speed MCI version. It also map sg and configure
1041 * PDC registers.
1042 */
1043static u32
1044atmci_prepare_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1045{
1046 u32 iflags, tmp;
1047 int i;
1048
1049 data->error = -EINPROGRESS;
1050
1051 host->data = data;
1052 host->sg = data->sg;
1053 iflags = ATMCI_DATA_ERROR_FLAGS;
1054
1055 /* Enable pdc mode */
1056 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCMODE);
1057
1058 if (data->flags & MMC_DATA_READ)
1059 iflags |= ATMCI_ENDRX | ATMCI_RXBUFF;
1060 else
1061 iflags |= ATMCI_ENDTX | ATMCI_TXBUFE | ATMCI_BLKE;
1062
1063 /* Set BLKLEN */
1064 tmp = atmci_readl(host, ATMCI_MR);
1065 tmp &= 0x0000ffff;
1066 tmp |= ATMCI_BLKLEN(data->blksz);
1067 atmci_writel(host, ATMCI_MR, tmp);
1068
1069 /* Configure PDC */
1070 host->data_size = data->blocks * data->blksz;
1071 dma_map_sg(&host->pdev->dev, data->sg, data->sg_len,
1072 mmc_get_dma_dir(data));
1073
1074 if ((!host->caps.has_rwproof)
1075 && (host->data->flags & MMC_DATA_WRITE)) {
1076 sg_copy_to_buffer(host->data->sg, host->data->sg_len,
1077 host->buffer, host->data_size);
1078 if (host->caps.has_bad_data_ordering)
1079 for (i = 0; i < host->data_size; i++)
1080 host->buffer[i] = swab32(host->buffer[i]);
1081 }
1082
1083 if (host->data_size)
1084 atmci_pdc_set_both_buf(host, data->flags & MMC_DATA_READ ?
1085 XFER_RECEIVE : XFER_TRANSMIT);
1086 return iflags;
1087}
1088
1089static u32
1090atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
1091{
1092 struct dma_chan *chan;
1093 struct dma_async_tx_descriptor *desc;
1094 struct scatterlist *sg;
1095 unsigned int i;
1096 enum dma_transfer_direction slave_dirn;
1097 unsigned int sglen;
1098 u32 maxburst;
1099 u32 iflags;
1100
1101 data->error = -EINPROGRESS;
1102
1103 WARN_ON(host->data);
1104 host->sg = NULL;
1105 host->data = data;
1106
1107 iflags = ATMCI_DATA_ERROR_FLAGS;
1108
1109 /*
1110 * We don't do DMA on "complex" transfers, i.e. with
1111 * non-word-aligned buffers or lengths. Also, we don't bother
1112 * with all the DMA setup overhead for short transfers.
1113 */
1114 if (data->blocks * data->blksz < ATMCI_DMA_THRESHOLD)
1115 return atmci_prepare_data(host, data);
1116 if (data->blksz & 3)
1117 return atmci_prepare_data(host, data);
1118
1119 for_each_sg(data->sg, sg, data->sg_len, i) {
1120 if (sg->offset & 3 || sg->length & 3)
1121 return atmci_prepare_data(host, data);
1122 }
1123
1124 /* If we don't have a channel, we can't do DMA */
1125 if (!host->dma.chan)
1126 return -ENODEV;
1127
1128 chan = host->dma.chan;
1129 host->data_chan = chan;
1130
1131 if (data->flags & MMC_DATA_READ) {
1132 host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
1133 maxburst = atmci_convert_chksize(host,
1134 host->dma_conf.src_maxburst);
1135 } else {
1136 host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
1137 maxburst = atmci_convert_chksize(host,
1138 host->dma_conf.dst_maxburst);
1139 }
1140
1141 if (host->caps.has_dma_conf_reg)
1142 atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) |
1143 ATMCI_DMAEN);
1144
1145 sglen = dma_map_sg(chan->device->dev, data->sg,
1146 data->sg_len, mmc_get_dma_dir(data));
1147
1148 dmaengine_slave_config(chan, &host->dma_conf);
1149 desc = dmaengine_prep_slave_sg(chan,
1150 data->sg, sglen, slave_dirn,
1151 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1152 if (!desc)
1153 goto unmap_exit;
1154
1155 host->dma.data_desc = desc;
1156 desc->callback = atmci_dma_complete;
1157 desc->callback_param = host;
1158
1159 return iflags;
1160unmap_exit:
1161 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len,
1162 mmc_get_dma_dir(data));
1163 return -ENOMEM;
1164}
1165
1166static void
1167atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
1168{
1169 return;
1170}
1171
1172/*
1173 * Start PDC according to transfer direction.
1174 */
1175static void
1176atmci_submit_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1177{
1178 if (data->flags & MMC_DATA_READ)
1179 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1180 else
1181 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1182}
1183
1184static void
1185atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
1186{
1187 struct dma_chan *chan = host->data_chan;
1188 struct dma_async_tx_descriptor *desc = host->dma.data_desc;
1189
1190 if (chan) {
1191 dmaengine_submit(desc);
1192 dma_async_issue_pending(chan);
1193 }
1194}
1195
1196static void atmci_stop_transfer(struct atmel_mci *host)
1197{
1198 dev_dbg(&host->pdev->dev,
1199 "(%s) set pending xfer complete\n", __func__);
1200 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1201 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1202}
1203
1204/*
1205 * Stop data transfer because error(s) occurred.
1206 */
1207static void atmci_stop_transfer_pdc(struct atmel_mci *host)
1208{
1209 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
1210}
1211
1212static void atmci_stop_transfer_dma(struct atmel_mci *host)
1213{
1214 struct dma_chan *chan = host->data_chan;
1215
1216 if (chan) {
1217 dmaengine_terminate_all(chan);
1218 atmci_dma_cleanup(host);
1219 } else {
1220 /* Data transfer was stopped by the interrupt handler */
1221 dev_dbg(&host->pdev->dev,
1222 "(%s) set pending xfer complete\n", __func__);
1223 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1224 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1225 }
1226}
1227
1228/*
1229 * Start a request: prepare data if needed, prepare the command and activate
1230 * interrupts.
1231 */
1232static void atmci_start_request(struct atmel_mci *host,
1233 struct atmel_mci_slot *slot)
1234{
1235 struct mmc_request *mrq;
1236 struct mmc_command *cmd;
1237 struct mmc_data *data;
1238 u32 iflags;
1239 u32 cmdflags;
1240
1241 mrq = slot->mrq;
1242 host->cur_slot = slot;
1243 host->mrq = mrq;
1244
1245 host->pending_events = 0;
1246 host->completed_events = 0;
1247 host->cmd_status = 0;
1248 host->data_status = 0;
1249
1250 dev_dbg(&host->pdev->dev, "start request: cmd %u\n", mrq->cmd->opcode);
1251
1252 if (host->need_reset || host->caps.need_reset_after_xfer) {
1253 iflags = atmci_readl(host, ATMCI_IMR);
1254 iflags &= (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB);
1255 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1256 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1257 atmci_writel(host, ATMCI_MR, host->mode_reg);
1258 if (host->caps.has_cfg_reg)
1259 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1260 atmci_writel(host, ATMCI_IER, iflags);
1261 host->need_reset = false;
1262 }
1263 atmci_writel(host, ATMCI_SDCR, slot->sdc_reg);
1264
1265 iflags = atmci_readl(host, ATMCI_IMR);
1266 if (iflags & ~(ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
1267 dev_dbg(&slot->mmc->class_dev, "WARNING: IMR=0x%08x\n",
1268 iflags);
1269
1270 if (unlikely(test_and_clear_bit(ATMCI_CARD_NEED_INIT, &slot->flags))) {
1271 /* Send init sequence (74 clock cycles) */
1272 atmci_writel(host, ATMCI_CMDR, ATMCI_CMDR_SPCMD_INIT);
1273 while (!(atmci_readl(host, ATMCI_SR) & ATMCI_CMDRDY))
1274 cpu_relax();
1275 }
1276 iflags = 0;
1277 data = mrq->data;
1278 if (data) {
1279 atmci_set_timeout(host, slot, data);
1280
1281 /* Must set block count/size before sending command */
1282 atmci_writel(host, ATMCI_BLKR, ATMCI_BCNT(data->blocks)
1283 | ATMCI_BLKLEN(data->blksz));
1284 dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n",
1285 ATMCI_BCNT(data->blocks) | ATMCI_BLKLEN(data->blksz));
1286
1287 iflags |= host->prepare_data(host, data);
1288 }
1289
1290 iflags |= ATMCI_CMDRDY;
1291 cmd = mrq->cmd;
1292 cmdflags = atmci_prepare_command(slot->mmc, cmd);
1293
1294 /*
1295 * DMA transfer should be started before sending the command to avoid
1296 * unexpected errors especially for read operations in SDIO mode.
1297 * Unfortunately, in PDC mode, command has to be sent before starting
1298 * the transfer.
1299 */
1300 if (host->submit_data != &atmci_submit_data_dma)
1301 atmci_send_command(host, cmd, cmdflags);
1302
1303 if (data)
1304 host->submit_data(host, data);
1305
1306 if (host->submit_data == &atmci_submit_data_dma)
1307 atmci_send_command(host, cmd, cmdflags);
1308
1309 if (mrq->stop) {
1310 host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop);
1311 host->stop_cmdr |= ATMCI_CMDR_STOP_XFER;
1312 if (!(data->flags & MMC_DATA_WRITE))
1313 host->stop_cmdr |= ATMCI_CMDR_TRDIR_READ;
1314 host->stop_cmdr |= ATMCI_CMDR_MULTI_BLOCK;
1315 }
1316
1317 /*
1318 * We could have enabled interrupts earlier, but I suspect
1319 * that would open up a nice can of interesting race
1320 * conditions (e.g. command and data complete, but stop not
1321 * prepared yet.)
1322 */
1323 atmci_writel(host, ATMCI_IER, iflags);
1324}
1325
1326static void atmci_queue_request(struct atmel_mci *host,
1327 struct atmel_mci_slot *slot, struct mmc_request *mrq)
1328{
1329 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1330 host->state);
1331
1332 spin_lock_bh(&host->lock);
1333 slot->mrq = mrq;
1334 if (host->state == STATE_IDLE) {
1335 host->state = STATE_SENDING_CMD;
1336 atmci_start_request(host, slot);
1337 } else {
1338 dev_dbg(&host->pdev->dev, "queue request\n");
1339 list_add_tail(&slot->queue_node, &host->queue);
1340 }
1341 spin_unlock_bh(&host->lock);
1342}
1343
1344static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1345{
1346 struct atmel_mci_slot *slot = mmc_priv(mmc);
1347 struct atmel_mci *host = slot->host;
1348 struct mmc_data *data;
1349
1350 WARN_ON(slot->mrq);
1351 dev_dbg(&host->pdev->dev, "MRQ: cmd %u\n", mrq->cmd->opcode);
1352
1353 /*
1354 * We may "know" the card is gone even though there's still an
1355 * electrical connection. If so, we really need to communicate
1356 * this to the MMC core since there won't be any more
1357 * interrupts as the card is completely removed. Otherwise,
1358 * the MMC core might believe the card is still there even
1359 * though the card was just removed very slowly.
1360 */
1361 if (!test_bit(ATMCI_CARD_PRESENT, &slot->flags)) {
1362 mrq->cmd->error = -ENOMEDIUM;
1363 mmc_request_done(mmc, mrq);
1364 return;
1365 }
1366
1367 /* We don't support multiple blocks of weird lengths. */
1368 data = mrq->data;
1369 if (data && data->blocks > 1 && data->blksz & 3) {
1370 mrq->cmd->error = -EINVAL;
1371 mmc_request_done(mmc, mrq);
1372 }
1373
1374 atmci_queue_request(host, slot, mrq);
1375}
1376
1377static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1378{
1379 struct atmel_mci_slot *slot = mmc_priv(mmc);
1380 struct atmel_mci *host = slot->host;
1381 unsigned int i;
1382
1383 slot->sdc_reg &= ~ATMCI_SDCBUS_MASK;
1384 switch (ios->bus_width) {
1385 case MMC_BUS_WIDTH_1:
1386 slot->sdc_reg |= ATMCI_SDCBUS_1BIT;
1387 break;
1388 case MMC_BUS_WIDTH_4:
1389 slot->sdc_reg |= ATMCI_SDCBUS_4BIT;
1390 break;
1391 case MMC_BUS_WIDTH_8:
1392 slot->sdc_reg |= ATMCI_SDCBUS_8BIT;
1393 break;
1394 }
1395
1396 if (ios->clock) {
1397 unsigned int clock_min = ~0U;
1398 int clkdiv;
1399
1400 spin_lock_bh(&host->lock);
1401 if (!host->mode_reg) {
1402 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1403 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1404 if (host->caps.has_cfg_reg)
1405 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1406 }
1407
1408 /*
1409 * Use mirror of ios->clock to prevent race with mmc
1410 * core ios update when finding the minimum.
1411 */
1412 slot->clock = ios->clock;
1413 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1414 if (host->slot[i] && host->slot[i]->clock
1415 && host->slot[i]->clock < clock_min)
1416 clock_min = host->slot[i]->clock;
1417 }
1418
1419 /* Calculate clock divider */
1420 if (host->caps.has_odd_clk_div) {
1421 clkdiv = DIV_ROUND_UP(host->bus_hz, clock_min) - 2;
1422 if (clkdiv < 0) {
1423 dev_warn(&mmc->class_dev,
1424 "clock %u too fast; using %lu\n",
1425 clock_min, host->bus_hz / 2);
1426 clkdiv = 0;
1427 } else if (clkdiv > 511) {
1428 dev_warn(&mmc->class_dev,
1429 "clock %u too slow; using %lu\n",
1430 clock_min, host->bus_hz / (511 + 2));
1431 clkdiv = 511;
1432 }
1433 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv >> 1)
1434 | ATMCI_MR_CLKODD(clkdiv & 1);
1435 } else {
1436 clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * clock_min) - 1;
1437 if (clkdiv > 255) {
1438 dev_warn(&mmc->class_dev,
1439 "clock %u too slow; using %lu\n",
1440 clock_min, host->bus_hz / (2 * 256));
1441 clkdiv = 255;
1442 }
1443 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv);
1444 }
1445
1446 /*
1447 * WRPROOF and RDPROOF prevent overruns/underruns by
1448 * stopping the clock when the FIFO is full/empty.
1449 * This state is not expected to last for long.
1450 */
1451 if (host->caps.has_rwproof)
1452 host->mode_reg |= (ATMCI_MR_WRPROOF | ATMCI_MR_RDPROOF);
1453
1454 if (host->caps.has_cfg_reg) {
1455 /* setup High Speed mode in relation with card capacity */
1456 if (ios->timing == MMC_TIMING_SD_HS)
1457 host->cfg_reg |= ATMCI_CFG_HSMODE;
1458 else
1459 host->cfg_reg &= ~ATMCI_CFG_HSMODE;
1460 }
1461
1462 if (list_empty(&host->queue)) {
1463 atmci_writel(host, ATMCI_MR, host->mode_reg);
1464 if (host->caps.has_cfg_reg)
1465 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1466 } else {
1467 host->need_clock_update = true;
1468 }
1469
1470 spin_unlock_bh(&host->lock);
1471 } else {
1472 bool any_slot_active = false;
1473
1474 spin_lock_bh(&host->lock);
1475 slot->clock = 0;
1476 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1477 if (host->slot[i] && host->slot[i]->clock) {
1478 any_slot_active = true;
1479 break;
1480 }
1481 }
1482 if (!any_slot_active) {
1483 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
1484 if (host->mode_reg) {
1485 atmci_readl(host, ATMCI_MR);
1486 }
1487 host->mode_reg = 0;
1488 }
1489 spin_unlock_bh(&host->lock);
1490 }
1491
1492 switch (ios->power_mode) {
1493 case MMC_POWER_OFF:
1494 if (!IS_ERR(mmc->supply.vmmc))
1495 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1496 break;
1497 case MMC_POWER_UP:
1498 set_bit(ATMCI_CARD_NEED_INIT, &slot->flags);
1499 if (!IS_ERR(mmc->supply.vmmc))
1500 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
1501 break;
1502 default:
1503 break;
1504 }
1505}
1506
1507static int atmci_get_ro(struct mmc_host *mmc)
1508{
1509 int read_only = -ENOSYS;
1510 struct atmel_mci_slot *slot = mmc_priv(mmc);
1511
1512 if (gpio_is_valid(slot->wp_pin)) {
1513 read_only = gpio_get_value(slot->wp_pin);
1514 dev_dbg(&mmc->class_dev, "card is %s\n",
1515 read_only ? "read-only" : "read-write");
1516 }
1517
1518 return read_only;
1519}
1520
1521static int atmci_get_cd(struct mmc_host *mmc)
1522{
1523 int present = -ENOSYS;
1524 struct atmel_mci_slot *slot = mmc_priv(mmc);
1525
1526 if (gpio_is_valid(slot->detect_pin)) {
1527 present = !(gpio_get_value(slot->detect_pin) ^
1528 slot->detect_is_active_high);
1529 dev_dbg(&mmc->class_dev, "card is %spresent\n",
1530 present ? "" : "not ");
1531 }
1532
1533 return present;
1534}
1535
1536static void atmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1537{
1538 struct atmel_mci_slot *slot = mmc_priv(mmc);
1539 struct atmel_mci *host = slot->host;
1540
1541 if (enable)
1542 atmci_writel(host, ATMCI_IER, slot->sdio_irq);
1543 else
1544 atmci_writel(host, ATMCI_IDR, slot->sdio_irq);
1545}
1546
1547static const struct mmc_host_ops atmci_ops = {
1548 .request = atmci_request,
1549 .set_ios = atmci_set_ios,
1550 .get_ro = atmci_get_ro,
1551 .get_cd = atmci_get_cd,
1552 .enable_sdio_irq = atmci_enable_sdio_irq,
1553};
1554
1555/* Called with host->lock held */
1556static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq)
1557 __releases(&host->lock)
1558 __acquires(&host->lock)
1559{
1560 struct atmel_mci_slot *slot = NULL;
1561 struct mmc_host *prev_mmc = host->cur_slot->mmc;
1562
1563 WARN_ON(host->cmd || host->data);
1564
1565 del_timer(&host->timer);
1566
1567 /*
1568 * Update the MMC clock rate if necessary. This may be
1569 * necessary if set_ios() is called when a different slot is
1570 * busy transferring data.
1571 */
1572 if (host->need_clock_update) {
1573 atmci_writel(host, ATMCI_MR, host->mode_reg);
1574 if (host->caps.has_cfg_reg)
1575 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1576 }
1577
1578 host->cur_slot->mrq = NULL;
1579 host->mrq = NULL;
1580 if (!list_empty(&host->queue)) {
1581 slot = list_entry(host->queue.next,
1582 struct atmel_mci_slot, queue_node);
1583 list_del(&slot->queue_node);
1584 dev_vdbg(&host->pdev->dev, "list not empty: %s is next\n",
1585 mmc_hostname(slot->mmc));
1586 host->state = STATE_SENDING_CMD;
1587 atmci_start_request(host, slot);
1588 } else {
1589 dev_vdbg(&host->pdev->dev, "list empty\n");
1590 host->state = STATE_IDLE;
1591 }
1592
1593 spin_unlock(&host->lock);
1594 mmc_request_done(prev_mmc, mrq);
1595 spin_lock(&host->lock);
1596}
1597
1598static void atmci_command_complete(struct atmel_mci *host,
1599 struct mmc_command *cmd)
1600{
1601 u32 status = host->cmd_status;
1602
1603 /* Read the response from the card (up to 16 bytes) */
1604 cmd->resp[0] = atmci_readl(host, ATMCI_RSPR);
1605 cmd->resp[1] = atmci_readl(host, ATMCI_RSPR);
1606 cmd->resp[2] = atmci_readl(host, ATMCI_RSPR);
1607 cmd->resp[3] = atmci_readl(host, ATMCI_RSPR);
1608
1609 if (status & ATMCI_RTOE)
1610 cmd->error = -ETIMEDOUT;
1611 else if ((cmd->flags & MMC_RSP_CRC) && (status & ATMCI_RCRCE))
1612 cmd->error = -EILSEQ;
1613 else if (status & (ATMCI_RINDE | ATMCI_RDIRE | ATMCI_RENDE))
1614 cmd->error = -EIO;
1615 else if (host->mrq->data && (host->mrq->data->blksz & 3)) {
1616 if (host->caps.need_blksz_mul_4) {
1617 cmd->error = -EINVAL;
1618 host->need_reset = 1;
1619 }
1620 } else
1621 cmd->error = 0;
1622}
1623
1624static void atmci_detect_change(struct timer_list *t)
1625{
1626 struct atmel_mci_slot *slot = from_timer(slot, t, detect_timer);
1627 bool present;
1628 bool present_old;
1629
1630 /*
1631 * atmci_cleanup_slot() sets the ATMCI_SHUTDOWN flag before
1632 * freeing the interrupt. We must not re-enable the interrupt
1633 * if it has been freed, and if we're shutting down, it
1634 * doesn't really matter whether the card is present or not.
1635 */
1636 smp_rmb();
1637 if (test_bit(ATMCI_SHUTDOWN, &slot->flags))
1638 return;
1639
1640 enable_irq(gpio_to_irq(slot->detect_pin));
1641 present = !(gpio_get_value(slot->detect_pin) ^
1642 slot->detect_is_active_high);
1643 present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
1644
1645 dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
1646 present, present_old);
1647
1648 if (present != present_old) {
1649 struct atmel_mci *host = slot->host;
1650 struct mmc_request *mrq;
1651
1652 dev_dbg(&slot->mmc->class_dev, "card %s\n",
1653 present ? "inserted" : "removed");
1654
1655 spin_lock(&host->lock);
1656
1657 if (!present)
1658 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
1659 else
1660 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
1661
1662 /* Clean up queue if present */
1663 mrq = slot->mrq;
1664 if (mrq) {
1665 if (mrq == host->mrq) {
1666 /*
1667 * Reset controller to terminate any ongoing
1668 * commands or data transfers.
1669 */
1670 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1671 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1672 atmci_writel(host, ATMCI_MR, host->mode_reg);
1673 if (host->caps.has_cfg_reg)
1674 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1675
1676 host->data = NULL;
1677 host->cmd = NULL;
1678
1679 switch (host->state) {
1680 case STATE_IDLE:
1681 break;
1682 case STATE_SENDING_CMD:
1683 mrq->cmd->error = -ENOMEDIUM;
1684 if (mrq->data)
1685 host->stop_transfer(host);
1686 break;
1687 case STATE_DATA_XFER:
1688 mrq->data->error = -ENOMEDIUM;
1689 host->stop_transfer(host);
1690 break;
1691 case STATE_WAITING_NOTBUSY:
1692 mrq->data->error = -ENOMEDIUM;
1693 break;
1694 case STATE_SENDING_STOP:
1695 mrq->stop->error = -ENOMEDIUM;
1696 break;
1697 case STATE_END_REQUEST:
1698 break;
1699 }
1700
1701 atmci_request_end(host, mrq);
1702 } else {
1703 list_del(&slot->queue_node);
1704 mrq->cmd->error = -ENOMEDIUM;
1705 if (mrq->data)
1706 mrq->data->error = -ENOMEDIUM;
1707 if (mrq->stop)
1708 mrq->stop->error = -ENOMEDIUM;
1709
1710 spin_unlock(&host->lock);
1711 mmc_request_done(slot->mmc, mrq);
1712 spin_lock(&host->lock);
1713 }
1714 }
1715 spin_unlock(&host->lock);
1716
1717 mmc_detect_change(slot->mmc, 0);
1718 }
1719}
1720
1721static void atmci_tasklet_func(struct tasklet_struct *t)
1722{
1723 struct atmel_mci *host = from_tasklet(host, t, tasklet);
1724 struct mmc_request *mrq = host->mrq;
1725 struct mmc_data *data = host->data;
1726 enum atmel_mci_state state = host->state;
1727 enum atmel_mci_state prev_state;
1728 u32 status;
1729
1730 spin_lock(&host->lock);
1731
1732 state = host->state;
1733
1734 dev_vdbg(&host->pdev->dev,
1735 "tasklet: state %u pending/completed/mask %lx/%lx/%x\n",
1736 state, host->pending_events, host->completed_events,
1737 atmci_readl(host, ATMCI_IMR));
1738
1739 do {
1740 prev_state = state;
1741 dev_dbg(&host->pdev->dev, "FSM: state=%d\n", state);
1742
1743 switch (state) {
1744 case STATE_IDLE:
1745 break;
1746
1747 case STATE_SENDING_CMD:
1748 /*
1749 * Command has been sent, we are waiting for command
1750 * ready. Then we have three next states possible:
1751 * END_REQUEST by default, WAITING_NOTBUSY if it's a
1752 * command needing it or DATA_XFER if there is data.
1753 */
1754 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1755 if (!atmci_test_and_clear_pending(host,
1756 EVENT_CMD_RDY))
1757 break;
1758
1759 dev_dbg(&host->pdev->dev, "set completed cmd ready\n");
1760 host->cmd = NULL;
1761 atmci_set_completed(host, EVENT_CMD_RDY);
1762 atmci_command_complete(host, mrq->cmd);
1763 if (mrq->data) {
1764 dev_dbg(&host->pdev->dev,
1765 "command with data transfer");
1766 /*
1767 * If there is a command error don't start
1768 * data transfer.
1769 */
1770 if (mrq->cmd->error) {
1771 host->stop_transfer(host);
1772 host->data = NULL;
1773 atmci_writel(host, ATMCI_IDR,
1774 ATMCI_TXRDY | ATMCI_RXRDY
1775 | ATMCI_DATA_ERROR_FLAGS);
1776 state = STATE_END_REQUEST;
1777 } else
1778 state = STATE_DATA_XFER;
1779 } else if ((!mrq->data) && (mrq->cmd->flags & MMC_RSP_BUSY)) {
1780 dev_dbg(&host->pdev->dev,
1781 "command response need waiting notbusy");
1782 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1783 state = STATE_WAITING_NOTBUSY;
1784 } else
1785 state = STATE_END_REQUEST;
1786
1787 break;
1788
1789 case STATE_DATA_XFER:
1790 if (atmci_test_and_clear_pending(host,
1791 EVENT_DATA_ERROR)) {
1792 dev_dbg(&host->pdev->dev, "set completed data error\n");
1793 atmci_set_completed(host, EVENT_DATA_ERROR);
1794 state = STATE_END_REQUEST;
1795 break;
1796 }
1797
1798 /*
1799 * A data transfer is in progress. The event expected
1800 * to move to the next state depends of data transfer
1801 * type (PDC or DMA). Once transfer done we can move
1802 * to the next step which is WAITING_NOTBUSY in write
1803 * case and directly SENDING_STOP in read case.
1804 */
1805 dev_dbg(&host->pdev->dev, "FSM: xfer complete?\n");
1806 if (!atmci_test_and_clear_pending(host,
1807 EVENT_XFER_COMPLETE))
1808 break;
1809
1810 dev_dbg(&host->pdev->dev,
1811 "(%s) set completed xfer complete\n",
1812 __func__);
1813 atmci_set_completed(host, EVENT_XFER_COMPLETE);
1814
1815 if (host->caps.need_notbusy_for_read_ops ||
1816 (host->data->flags & MMC_DATA_WRITE)) {
1817 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1818 state = STATE_WAITING_NOTBUSY;
1819 } else if (host->mrq->stop) {
1820 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
1821 atmci_send_stop_cmd(host, data);
1822 state = STATE_SENDING_STOP;
1823 } else {
1824 host->data = NULL;
1825 data->bytes_xfered = data->blocks * data->blksz;
1826 data->error = 0;
1827 state = STATE_END_REQUEST;
1828 }
1829 break;
1830
1831 case STATE_WAITING_NOTBUSY:
1832 /*
1833 * We can be in the state for two reasons: a command
1834 * requiring waiting not busy signal (stop command
1835 * included) or a write operation. In the latest case,
1836 * we need to send a stop command.
1837 */
1838 dev_dbg(&host->pdev->dev, "FSM: not busy?\n");
1839 if (!atmci_test_and_clear_pending(host,
1840 EVENT_NOTBUSY))
1841 break;
1842
1843 dev_dbg(&host->pdev->dev, "set completed not busy\n");
1844 atmci_set_completed(host, EVENT_NOTBUSY);
1845
1846 if (host->data) {
1847 /*
1848 * For some commands such as CMD53, even if
1849 * there is data transfer, there is no stop
1850 * command to send.
1851 */
1852 if (host->mrq->stop) {
1853 atmci_writel(host, ATMCI_IER,
1854 ATMCI_CMDRDY);
1855 atmci_send_stop_cmd(host, data);
1856 state = STATE_SENDING_STOP;
1857 } else {
1858 host->data = NULL;
1859 data->bytes_xfered = data->blocks
1860 * data->blksz;
1861 data->error = 0;
1862 state = STATE_END_REQUEST;
1863 }
1864 } else
1865 state = STATE_END_REQUEST;
1866 break;
1867
1868 case STATE_SENDING_STOP:
1869 /*
1870 * In this state, it is important to set host->data to
1871 * NULL (which is tested in the waiting notbusy state)
1872 * in order to go to the end request state instead of
1873 * sending stop again.
1874 */
1875 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1876 if (!atmci_test_and_clear_pending(host,
1877 EVENT_CMD_RDY))
1878 break;
1879
1880 dev_dbg(&host->pdev->dev, "FSM: cmd ready\n");
1881 host->cmd = NULL;
1882 data->bytes_xfered = data->blocks * data->blksz;
1883 data->error = 0;
1884 atmci_command_complete(host, mrq->stop);
1885 if (mrq->stop->error) {
1886 host->stop_transfer(host);
1887 atmci_writel(host, ATMCI_IDR,
1888 ATMCI_TXRDY | ATMCI_RXRDY
1889 | ATMCI_DATA_ERROR_FLAGS);
1890 state = STATE_END_REQUEST;
1891 } else {
1892 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1893 state = STATE_WAITING_NOTBUSY;
1894 }
1895 host->data = NULL;
1896 break;
1897
1898 case STATE_END_REQUEST:
1899 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY | ATMCI_RXRDY
1900 | ATMCI_DATA_ERROR_FLAGS);
1901 status = host->data_status;
1902 if (unlikely(status)) {
1903 host->stop_transfer(host);
1904 host->data = NULL;
1905 if (data) {
1906 if (status & ATMCI_DTOE) {
1907 data->error = -ETIMEDOUT;
1908 } else if (status & ATMCI_DCRCE) {
1909 data->error = -EILSEQ;
1910 } else {
1911 data->error = -EIO;
1912 }
1913 }
1914 }
1915
1916 atmci_request_end(host, host->mrq);
1917 goto unlock; /* atmci_request_end() sets host->state */
1918 break;
1919 }
1920 } while (state != prev_state);
1921
1922 host->state = state;
1923
1924unlock:
1925 spin_unlock(&host->lock);
1926}
1927
1928static void atmci_read_data_pio(struct atmel_mci *host)
1929{
1930 struct scatterlist *sg = host->sg;
1931 unsigned int offset = host->pio_offset;
1932 struct mmc_data *data = host->data;
1933 u32 value;
1934 u32 status;
1935 unsigned int nbytes = 0;
1936
1937 do {
1938 value = atmci_readl(host, ATMCI_RDR);
1939 if (likely(offset + 4 <= sg->length)) {
1940 sg_pcopy_from_buffer(sg, 1, &value, sizeof(u32), offset);
1941
1942 offset += 4;
1943 nbytes += 4;
1944
1945 if (offset == sg->length) {
1946 flush_dcache_page(sg_page(sg));
1947 host->sg = sg = sg_next(sg);
1948 host->sg_len--;
1949 if (!sg || !host->sg_len)
1950 goto done;
1951
1952 offset = 0;
1953 }
1954 } else {
1955 unsigned int remaining = sg->length - offset;
1956
1957 sg_pcopy_from_buffer(sg, 1, &value, remaining, offset);
1958 nbytes += remaining;
1959
1960 flush_dcache_page(sg_page(sg));
1961 host->sg = sg = sg_next(sg);
1962 host->sg_len--;
1963 if (!sg || !host->sg_len)
1964 goto done;
1965
1966 offset = 4 - remaining;
1967 sg_pcopy_from_buffer(sg, 1, (u8 *)&value + remaining,
1968 offset, 0);
1969 nbytes += offset;
1970 }
1971
1972 status = atmci_readl(host, ATMCI_SR);
1973 if (status & ATMCI_DATA_ERROR_FLAGS) {
1974 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_RXRDY
1975 | ATMCI_DATA_ERROR_FLAGS));
1976 host->data_status = status;
1977 data->bytes_xfered += nbytes;
1978 return;
1979 }
1980 } while (status & ATMCI_RXRDY);
1981
1982 host->pio_offset = offset;
1983 data->bytes_xfered += nbytes;
1984
1985 return;
1986
1987done:
1988 atmci_writel(host, ATMCI_IDR, ATMCI_RXRDY);
1989 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1990 data->bytes_xfered += nbytes;
1991 smp_wmb();
1992 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1993}
1994
1995static void atmci_write_data_pio(struct atmel_mci *host)
1996{
1997 struct scatterlist *sg = host->sg;
1998 unsigned int offset = host->pio_offset;
1999 struct mmc_data *data = host->data;
2000 u32 value;
2001 u32 status;
2002 unsigned int nbytes = 0;
2003
2004 do {
2005 if (likely(offset + 4 <= sg->length)) {
2006 sg_pcopy_to_buffer(sg, 1, &value, sizeof(u32), offset);
2007 atmci_writel(host, ATMCI_TDR, value);
2008
2009 offset += 4;
2010 nbytes += 4;
2011 if (offset == sg->length) {
2012 host->sg = sg = sg_next(sg);
2013 host->sg_len--;
2014 if (!sg || !host->sg_len)
2015 goto done;
2016
2017 offset = 0;
2018 }
2019 } else {
2020 unsigned int remaining = sg->length - offset;
2021
2022 value = 0;
2023 sg_pcopy_to_buffer(sg, 1, &value, remaining, offset);
2024 nbytes += remaining;
2025
2026 host->sg = sg = sg_next(sg);
2027 host->sg_len--;
2028 if (!sg || !host->sg_len) {
2029 atmci_writel(host, ATMCI_TDR, value);
2030 goto done;
2031 }
2032
2033 offset = 4 - remaining;
2034 sg_pcopy_to_buffer(sg, 1, (u8 *)&value + remaining,
2035 offset, 0);
2036 atmci_writel(host, ATMCI_TDR, value);
2037 nbytes += offset;
2038 }
2039
2040 status = atmci_readl(host, ATMCI_SR);
2041 if (status & ATMCI_DATA_ERROR_FLAGS) {
2042 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_TXRDY
2043 | ATMCI_DATA_ERROR_FLAGS));
2044 host->data_status = status;
2045 data->bytes_xfered += nbytes;
2046 return;
2047 }
2048 } while (status & ATMCI_TXRDY);
2049
2050 host->pio_offset = offset;
2051 data->bytes_xfered += nbytes;
2052
2053 return;
2054
2055done:
2056 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY);
2057 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2058 data->bytes_xfered += nbytes;
2059 smp_wmb();
2060 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2061}
2062
2063static void atmci_sdio_interrupt(struct atmel_mci *host, u32 status)
2064{
2065 int i;
2066
2067 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2068 struct atmel_mci_slot *slot = host->slot[i];
2069 if (slot && (status & slot->sdio_irq)) {
2070 mmc_signal_sdio_irq(slot->mmc);
2071 }
2072 }
2073}
2074
2075
2076static irqreturn_t atmci_interrupt(int irq, void *dev_id)
2077{
2078 struct atmel_mci *host = dev_id;
2079 u32 status, mask, pending;
2080 unsigned int pass_count = 0;
2081
2082 do {
2083 status = atmci_readl(host, ATMCI_SR);
2084 mask = atmci_readl(host, ATMCI_IMR);
2085 pending = status & mask;
2086 if (!pending)
2087 break;
2088
2089 if (pending & ATMCI_DATA_ERROR_FLAGS) {
2090 dev_dbg(&host->pdev->dev, "IRQ: data error\n");
2091 atmci_writel(host, ATMCI_IDR, ATMCI_DATA_ERROR_FLAGS
2092 | ATMCI_RXRDY | ATMCI_TXRDY
2093 | ATMCI_ENDRX | ATMCI_ENDTX
2094 | ATMCI_RXBUFF | ATMCI_TXBUFE);
2095
2096 host->data_status = status;
2097 dev_dbg(&host->pdev->dev, "set pending data error\n");
2098 smp_wmb();
2099 atmci_set_pending(host, EVENT_DATA_ERROR);
2100 tasklet_schedule(&host->tasklet);
2101 }
2102
2103 if (pending & ATMCI_TXBUFE) {
2104 dev_dbg(&host->pdev->dev, "IRQ: tx buffer empty\n");
2105 atmci_writel(host, ATMCI_IDR, ATMCI_TXBUFE);
2106 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2107 /*
2108 * We can receive this interruption before having configured
2109 * the second pdc buffer, so we need to reconfigure first and
2110 * second buffers again
2111 */
2112 if (host->data_size) {
2113 atmci_pdc_set_both_buf(host, XFER_TRANSMIT);
2114 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2115 atmci_writel(host, ATMCI_IER, ATMCI_TXBUFE);
2116 } else {
2117 atmci_pdc_complete(host);
2118 }
2119 } else if (pending & ATMCI_ENDTX) {
2120 dev_dbg(&host->pdev->dev, "IRQ: end of tx buffer\n");
2121 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2122
2123 if (host->data_size) {
2124 atmci_pdc_set_single_buf(host,
2125 XFER_TRANSMIT, PDC_SECOND_BUF);
2126 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2127 }
2128 }
2129
2130 if (pending & ATMCI_RXBUFF) {
2131 dev_dbg(&host->pdev->dev, "IRQ: rx buffer full\n");
2132 atmci_writel(host, ATMCI_IDR, ATMCI_RXBUFF);
2133 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2134 /*
2135 * We can receive this interruption before having configured
2136 * the second pdc buffer, so we need to reconfigure first and
2137 * second buffers again
2138 */
2139 if (host->data_size) {
2140 atmci_pdc_set_both_buf(host, XFER_RECEIVE);
2141 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2142 atmci_writel(host, ATMCI_IER, ATMCI_RXBUFF);
2143 } else {
2144 atmci_pdc_complete(host);
2145 }
2146 } else if (pending & ATMCI_ENDRX) {
2147 dev_dbg(&host->pdev->dev, "IRQ: end of rx buffer\n");
2148 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2149
2150 if (host->data_size) {
2151 atmci_pdc_set_single_buf(host,
2152 XFER_RECEIVE, PDC_SECOND_BUF);
2153 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2154 }
2155 }
2156
2157 /*
2158 * First mci IPs, so mainly the ones having pdc, have some
2159 * issues with the notbusy signal. You can't get it after
2160 * data transmission if you have not sent a stop command.
2161 * The appropriate workaround is to use the BLKE signal.
2162 */
2163 if (pending & ATMCI_BLKE) {
2164 dev_dbg(&host->pdev->dev, "IRQ: blke\n");
2165 atmci_writel(host, ATMCI_IDR, ATMCI_BLKE);
2166 smp_wmb();
2167 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2168 atmci_set_pending(host, EVENT_NOTBUSY);
2169 tasklet_schedule(&host->tasklet);
2170 }
2171
2172 if (pending & ATMCI_NOTBUSY) {
2173 dev_dbg(&host->pdev->dev, "IRQ: not_busy\n");
2174 atmci_writel(host, ATMCI_IDR, ATMCI_NOTBUSY);
2175 smp_wmb();
2176 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2177 atmci_set_pending(host, EVENT_NOTBUSY);
2178 tasklet_schedule(&host->tasklet);
2179 }
2180
2181 if (pending & ATMCI_RXRDY)
2182 atmci_read_data_pio(host);
2183 if (pending & ATMCI_TXRDY)
2184 atmci_write_data_pio(host);
2185
2186 if (pending & ATMCI_CMDRDY) {
2187 dev_dbg(&host->pdev->dev, "IRQ: cmd ready\n");
2188 atmci_writel(host, ATMCI_IDR, ATMCI_CMDRDY);
2189 host->cmd_status = status;
2190 smp_wmb();
2191 dev_dbg(&host->pdev->dev, "set pending cmd rdy\n");
2192 atmci_set_pending(host, EVENT_CMD_RDY);
2193 tasklet_schedule(&host->tasklet);
2194 }
2195
2196 if (pending & (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
2197 atmci_sdio_interrupt(host, status);
2198
2199 } while (pass_count++ < 5);
2200
2201 return pass_count ? IRQ_HANDLED : IRQ_NONE;
2202}
2203
2204static irqreturn_t atmci_detect_interrupt(int irq, void *dev_id)
2205{
2206 struct atmel_mci_slot *slot = dev_id;
2207
2208 /*
2209 * Disable interrupts until the pin has stabilized and check
2210 * the state then. Use mod_timer() since we may be in the
2211 * middle of the timer routine when this interrupt triggers.
2212 */
2213 disable_irq_nosync(irq);
2214 mod_timer(&slot->detect_timer, jiffies + msecs_to_jiffies(20));
2215
2216 return IRQ_HANDLED;
2217}
2218
2219static int atmci_init_slot(struct atmel_mci *host,
2220 struct mci_slot_pdata *slot_data, unsigned int id,
2221 u32 sdc_reg, u32 sdio_irq)
2222{
2223 struct mmc_host *mmc;
2224 struct atmel_mci_slot *slot;
2225 int ret;
2226
2227 mmc = mmc_alloc_host(sizeof(struct atmel_mci_slot), &host->pdev->dev);
2228 if (!mmc)
2229 return -ENOMEM;
2230
2231 slot = mmc_priv(mmc);
2232 slot->mmc = mmc;
2233 slot->host = host;
2234 slot->detect_pin = slot_data->detect_pin;
2235 slot->wp_pin = slot_data->wp_pin;
2236 slot->detect_is_active_high = slot_data->detect_is_active_high;
2237 slot->sdc_reg = sdc_reg;
2238 slot->sdio_irq = sdio_irq;
2239
2240 dev_dbg(&mmc->class_dev,
2241 "slot[%u]: bus_width=%u, detect_pin=%d, "
2242 "detect_is_active_high=%s, wp_pin=%d\n",
2243 id, slot_data->bus_width, slot_data->detect_pin,
2244 slot_data->detect_is_active_high ? "true" : "false",
2245 slot_data->wp_pin);
2246
2247 mmc->ops = &atmci_ops;
2248 mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
2249 mmc->f_max = host->bus_hz / 2;
2250 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2251 if (sdio_irq)
2252 mmc->caps |= MMC_CAP_SDIO_IRQ;
2253 if (host->caps.has_highspeed)
2254 mmc->caps |= MMC_CAP_SD_HIGHSPEED;
2255 /*
2256 * Without the read/write proof capability, it is strongly suggested to
2257 * use only one bit for data to prevent fifo underruns and overruns
2258 * which will corrupt data.
2259 */
2260 if ((slot_data->bus_width >= 4) && host->caps.has_rwproof) {
2261 mmc->caps |= MMC_CAP_4_BIT_DATA;
2262 if (slot_data->bus_width >= 8)
2263 mmc->caps |= MMC_CAP_8_BIT_DATA;
2264 }
2265
2266 if (atmci_get_version(host) < 0x200) {
2267 mmc->max_segs = 256;
2268 mmc->max_blk_size = 4095;
2269 mmc->max_blk_count = 256;
2270 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2271 mmc->max_seg_size = mmc->max_blk_size * mmc->max_segs;
2272 } else {
2273 mmc->max_segs = 64;
2274 mmc->max_req_size = 32768 * 512;
2275 mmc->max_blk_size = 32768;
2276 mmc->max_blk_count = 512;
2277 }
2278
2279 /* Assume card is present initially */
2280 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
2281 if (gpio_is_valid(slot->detect_pin)) {
2282 if (devm_gpio_request(&host->pdev->dev, slot->detect_pin,
2283 "mmc_detect")) {
2284 dev_dbg(&mmc->class_dev, "no detect pin available\n");
2285 slot->detect_pin = -EBUSY;
2286 } else if (gpio_get_value(slot->detect_pin) ^
2287 slot->detect_is_active_high) {
2288 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
2289 }
2290 }
2291
2292 if (!gpio_is_valid(slot->detect_pin)) {
2293 if (slot_data->non_removable)
2294 mmc->caps |= MMC_CAP_NONREMOVABLE;
2295 else
2296 mmc->caps |= MMC_CAP_NEEDS_POLL;
2297 }
2298
2299 if (gpio_is_valid(slot->wp_pin)) {
2300 if (devm_gpio_request(&host->pdev->dev, slot->wp_pin,
2301 "mmc_wp")) {
2302 dev_dbg(&mmc->class_dev, "no WP pin available\n");
2303 slot->wp_pin = -EBUSY;
2304 }
2305 }
2306
2307 host->slot[id] = slot;
2308 mmc_regulator_get_supply(mmc);
2309 ret = mmc_add_host(mmc);
2310 if (ret) {
2311 mmc_free_host(mmc);
2312 return ret;
2313 }
2314
2315 if (gpio_is_valid(slot->detect_pin)) {
2316 timer_setup(&slot->detect_timer, atmci_detect_change, 0);
2317
2318 ret = request_irq(gpio_to_irq(slot->detect_pin),
2319 atmci_detect_interrupt,
2320 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
2321 "mmc-detect", slot);
2322 if (ret) {
2323 dev_dbg(&mmc->class_dev,
2324 "could not request IRQ %d for detect pin\n",
2325 gpio_to_irq(slot->detect_pin));
2326 slot->detect_pin = -EBUSY;
2327 }
2328 }
2329
2330 atmci_init_debugfs(slot);
2331
2332 return 0;
2333}
2334
2335static void atmci_cleanup_slot(struct atmel_mci_slot *slot,
2336 unsigned int id)
2337{
2338 /* Debugfs stuff is cleaned up by mmc core */
2339
2340 set_bit(ATMCI_SHUTDOWN, &slot->flags);
2341 smp_wmb();
2342
2343 mmc_remove_host(slot->mmc);
2344
2345 if (gpio_is_valid(slot->detect_pin)) {
2346 int pin = slot->detect_pin;
2347
2348 free_irq(gpio_to_irq(pin), slot);
2349 del_timer_sync(&slot->detect_timer);
2350 }
2351
2352 slot->host->slot[id] = NULL;
2353 mmc_free_host(slot->mmc);
2354}
2355
2356static int atmci_configure_dma(struct atmel_mci *host)
2357{
2358 host->dma.chan = dma_request_chan(&host->pdev->dev, "rxtx");
2359
2360 if (PTR_ERR(host->dma.chan) == -ENODEV) {
2361 struct mci_platform_data *pdata = host->pdev->dev.platform_data;
2362 dma_cap_mask_t mask;
2363
2364 if (!pdata || !pdata->dma_filter)
2365 return -ENODEV;
2366
2367 dma_cap_zero(mask);
2368 dma_cap_set(DMA_SLAVE, mask);
2369
2370 host->dma.chan = dma_request_channel(mask, pdata->dma_filter,
2371 pdata->dma_slave);
2372 if (!host->dma.chan)
2373 host->dma.chan = ERR_PTR(-ENODEV);
2374 }
2375
2376 if (IS_ERR(host->dma.chan))
2377 return PTR_ERR(host->dma.chan);
2378
2379 dev_info(&host->pdev->dev, "using %s for DMA transfers\n",
2380 dma_chan_name(host->dma.chan));
2381
2382 host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
2383 host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2384 host->dma_conf.src_maxburst = 1;
2385 host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
2386 host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2387 host->dma_conf.dst_maxburst = 1;
2388 host->dma_conf.device_fc = false;
2389
2390 return 0;
2391}
2392
2393/*
2394 * HSMCI (High Speed MCI) module is not fully compatible with MCI module.
2395 * HSMCI provides DMA support and a new config register but no more supports
2396 * PDC.
2397 */
2398static void atmci_get_cap(struct atmel_mci *host)
2399{
2400 unsigned int version;
2401
2402 version = atmci_get_version(host);
2403 dev_info(&host->pdev->dev,
2404 "version: 0x%x\n", version);
2405
2406 host->caps.has_dma_conf_reg = false;
2407 host->caps.has_pdc = true;
2408 host->caps.has_cfg_reg = false;
2409 host->caps.has_cstor_reg = false;
2410 host->caps.has_highspeed = false;
2411 host->caps.has_rwproof = false;
2412 host->caps.has_odd_clk_div = false;
2413 host->caps.has_bad_data_ordering = true;
2414 host->caps.need_reset_after_xfer = true;
2415 host->caps.need_blksz_mul_4 = true;
2416 host->caps.need_notbusy_for_read_ops = false;
2417
2418 /* keep only major version number */
2419 switch (version & 0xf00) {
2420 case 0x600:
2421 case 0x500:
2422 host->caps.has_odd_clk_div = true;
2423 fallthrough;
2424 case 0x400:
2425 case 0x300:
2426 host->caps.has_dma_conf_reg = true;
2427 host->caps.has_pdc = false;
2428 host->caps.has_cfg_reg = true;
2429 host->caps.has_cstor_reg = true;
2430 host->caps.has_highspeed = true;
2431 fallthrough;
2432 case 0x200:
2433 host->caps.has_rwproof = true;
2434 host->caps.need_blksz_mul_4 = false;
2435 host->caps.need_notbusy_for_read_ops = true;
2436 fallthrough;
2437 case 0x100:
2438 host->caps.has_bad_data_ordering = false;
2439 host->caps.need_reset_after_xfer = false;
2440 fallthrough;
2441 case 0x0:
2442 break;
2443 default:
2444 host->caps.has_pdc = false;
2445 dev_warn(&host->pdev->dev,
2446 "Unmanaged mci version, set minimum capabilities\n");
2447 break;
2448 }
2449}
2450
2451static int atmci_probe(struct platform_device *pdev)
2452{
2453 struct mci_platform_data *pdata;
2454 struct atmel_mci *host;
2455 struct resource *regs;
2456 unsigned int nr_slots;
2457 int irq;
2458 int ret, i;
2459
2460 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2461 if (!regs)
2462 return -ENXIO;
2463 pdata = pdev->dev.platform_data;
2464 if (!pdata) {
2465 pdata = atmci_of_init(pdev);
2466 if (IS_ERR(pdata)) {
2467 dev_err(&pdev->dev, "platform data not available\n");
2468 return PTR_ERR(pdata);
2469 }
2470 }
2471
2472 irq = platform_get_irq(pdev, 0);
2473 if (irq < 0)
2474 return irq;
2475
2476 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
2477 if (!host)
2478 return -ENOMEM;
2479
2480 host->pdev = pdev;
2481 spin_lock_init(&host->lock);
2482 INIT_LIST_HEAD(&host->queue);
2483
2484 host->mck = devm_clk_get(&pdev->dev, "mci_clk");
2485 if (IS_ERR(host->mck))
2486 return PTR_ERR(host->mck);
2487
2488 host->regs = devm_ioremap(&pdev->dev, regs->start, resource_size(regs));
2489 if (!host->regs)
2490 return -ENOMEM;
2491
2492 ret = clk_prepare_enable(host->mck);
2493 if (ret)
2494 return ret;
2495
2496 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
2497 host->bus_hz = clk_get_rate(host->mck);
2498
2499 host->mapbase = regs->start;
2500
2501 tasklet_setup(&host->tasklet, atmci_tasklet_func);
2502
2503 ret = request_irq(irq, atmci_interrupt, 0, dev_name(&pdev->dev), host);
2504 if (ret) {
2505 clk_disable_unprepare(host->mck);
2506 return ret;
2507 }
2508
2509 /* Get MCI capabilities and set operations according to it */
2510 atmci_get_cap(host);
2511 ret = atmci_configure_dma(host);
2512 if (ret == -EPROBE_DEFER)
2513 goto err_dma_probe_defer;
2514 if (ret == 0) {
2515 host->prepare_data = &atmci_prepare_data_dma;
2516 host->submit_data = &atmci_submit_data_dma;
2517 host->stop_transfer = &atmci_stop_transfer_dma;
2518 } else if (host->caps.has_pdc) {
2519 dev_info(&pdev->dev, "using PDC\n");
2520 host->prepare_data = &atmci_prepare_data_pdc;
2521 host->submit_data = &atmci_submit_data_pdc;
2522 host->stop_transfer = &atmci_stop_transfer_pdc;
2523 } else {
2524 dev_info(&pdev->dev, "using PIO\n");
2525 host->prepare_data = &atmci_prepare_data;
2526 host->submit_data = &atmci_submit_data;
2527 host->stop_transfer = &atmci_stop_transfer;
2528 }
2529
2530 platform_set_drvdata(pdev, host);
2531
2532 timer_setup(&host->timer, atmci_timeout_timer, 0);
2533
2534 pm_runtime_get_noresume(&pdev->dev);
2535 pm_runtime_set_active(&pdev->dev);
2536 pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_DELAY);
2537 pm_runtime_use_autosuspend(&pdev->dev);
2538 pm_runtime_enable(&pdev->dev);
2539
2540 /* We need at least one slot to succeed */
2541 nr_slots = 0;
2542 ret = -ENODEV;
2543 if (pdata->slot[0].bus_width) {
2544 ret = atmci_init_slot(host, &pdata->slot[0],
2545 0, ATMCI_SDCSEL_SLOT_A, ATMCI_SDIOIRQA);
2546 if (!ret) {
2547 nr_slots++;
2548 host->buf_size = host->slot[0]->mmc->max_req_size;
2549 }
2550 }
2551 if (pdata->slot[1].bus_width) {
2552 ret = atmci_init_slot(host, &pdata->slot[1],
2553 1, ATMCI_SDCSEL_SLOT_B, ATMCI_SDIOIRQB);
2554 if (!ret) {
2555 nr_slots++;
2556 if (host->slot[1]->mmc->max_req_size > host->buf_size)
2557 host->buf_size =
2558 host->slot[1]->mmc->max_req_size;
2559 }
2560 }
2561
2562 if (!nr_slots) {
2563 dev_err(&pdev->dev, "init failed: no slot defined\n");
2564 goto err_init_slot;
2565 }
2566
2567 if (!host->caps.has_rwproof) {
2568 host->buffer = dma_alloc_coherent(&pdev->dev, host->buf_size,
2569 &host->buf_phys_addr,
2570 GFP_KERNEL);
2571 if (!host->buffer) {
2572 ret = -ENOMEM;
2573 dev_err(&pdev->dev, "buffer allocation failed\n");
2574 goto err_dma_alloc;
2575 }
2576 }
2577
2578 dev_info(&pdev->dev,
2579 "Atmel MCI controller at 0x%08lx irq %d, %u slots\n",
2580 host->mapbase, irq, nr_slots);
2581
2582 pm_runtime_mark_last_busy(&host->pdev->dev);
2583 pm_runtime_put_autosuspend(&pdev->dev);
2584
2585 return 0;
2586
2587err_dma_alloc:
2588 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2589 if (host->slot[i])
2590 atmci_cleanup_slot(host->slot[i], i);
2591 }
2592err_init_slot:
2593 clk_disable_unprepare(host->mck);
2594
2595 pm_runtime_disable(&pdev->dev);
2596 pm_runtime_put_noidle(&pdev->dev);
2597
2598 del_timer_sync(&host->timer);
2599 if (!IS_ERR(host->dma.chan))
2600 dma_release_channel(host->dma.chan);
2601err_dma_probe_defer:
2602 free_irq(irq, host);
2603 return ret;
2604}
2605
2606static int atmci_remove(struct platform_device *pdev)
2607{
2608 struct atmel_mci *host = platform_get_drvdata(pdev);
2609 unsigned int i;
2610
2611 pm_runtime_get_sync(&pdev->dev);
2612
2613 if (host->buffer)
2614 dma_free_coherent(&pdev->dev, host->buf_size,
2615 host->buffer, host->buf_phys_addr);
2616
2617 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2618 if (host->slot[i])
2619 atmci_cleanup_slot(host->slot[i], i);
2620 }
2621
2622 atmci_writel(host, ATMCI_IDR, ~0UL);
2623 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
2624 atmci_readl(host, ATMCI_SR);
2625
2626 del_timer_sync(&host->timer);
2627 if (!IS_ERR(host->dma.chan))
2628 dma_release_channel(host->dma.chan);
2629
2630 free_irq(platform_get_irq(pdev, 0), host);
2631
2632 clk_disable_unprepare(host->mck);
2633
2634 pm_runtime_disable(&pdev->dev);
2635 pm_runtime_put_noidle(&pdev->dev);
2636
2637 return 0;
2638}
2639
2640#ifdef CONFIG_PM
2641static int atmci_runtime_suspend(struct device *dev)
2642{
2643 struct atmel_mci *host = dev_get_drvdata(dev);
2644
2645 clk_disable_unprepare(host->mck);
2646
2647 pinctrl_pm_select_sleep_state(dev);
2648
2649 return 0;
2650}
2651
2652static int atmci_runtime_resume(struct device *dev)
2653{
2654 struct atmel_mci *host = dev_get_drvdata(dev);
2655
2656 pinctrl_select_default_state(dev);
2657
2658 return clk_prepare_enable(host->mck);
2659}
2660#endif
2661
2662static const struct dev_pm_ops atmci_dev_pm_ops = {
2663 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
2664 pm_runtime_force_resume)
2665 SET_RUNTIME_PM_OPS(atmci_runtime_suspend, atmci_runtime_resume, NULL)
2666};
2667
2668static struct platform_driver atmci_driver = {
2669 .probe = atmci_probe,
2670 .remove = atmci_remove,
2671 .driver = {
2672 .name = "atmel_mci",
2673 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
2674 .of_match_table = of_match_ptr(atmci_dt_ids),
2675 .pm = &atmci_dev_pm_ops,
2676 },
2677};
2678module_platform_driver(atmci_driver);
2679
2680MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver");
2681MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
2682MODULE_LICENSE("GPL v2");
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Atmel MultiMedia Card Interface driver
4 *
5 * Copyright (C) 2004-2008 Atmel Corporation
6 */
7#include <linux/blkdev.h>
8#include <linux/clk.h>
9#include <linux/debugfs.h>
10#include <linux/device.h>
11#include <linux/dmaengine.h>
12#include <linux/dma-mapping.h>
13#include <linux/err.h>
14#include <linux/init.h>
15#include <linux/interrupt.h>
16#include <linux/io.h>
17#include <linux/ioport.h>
18#include <linux/module.h>
19#include <linux/of.h>
20#include <linux/irq.h>
21#include <linux/gpio/consumer.h>
22#include <linux/platform_device.h>
23#include <linux/scatterlist.h>
24#include <linux/seq_file.h>
25#include <linux/slab.h>
26#include <linux/stat.h>
27#include <linux/types.h>
28
29#include <linux/mmc/host.h>
30#include <linux/mmc/sdio.h>
31
32#include <linux/atmel_pdc.h>
33#include <linux/pm.h>
34#include <linux/pm_runtime.h>
35#include <linux/pinctrl/consumer.h>
36#include <linux/workqueue.h>
37
38#include <asm/cacheflush.h>
39#include <asm/io.h>
40#include <linux/unaligned.h>
41
42#define ATMCI_MAX_NR_SLOTS 2
43
44/*
45 * Superset of MCI IP registers integrated in Atmel AT91 Processor
46 * Registers and bitfields marked with [2] are only available in MCI2
47 */
48
49/* MCI Register Definitions */
50#define ATMCI_CR 0x0000 /* Control */
51#define ATMCI_CR_MCIEN BIT(0) /* MCI Enable */
52#define ATMCI_CR_MCIDIS BIT(1) /* MCI Disable */
53#define ATMCI_CR_PWSEN BIT(2) /* Power Save Enable */
54#define ATMCI_CR_PWSDIS BIT(3) /* Power Save Disable */
55#define ATMCI_CR_SWRST BIT(7) /* Software Reset */
56#define ATMCI_MR 0x0004 /* Mode */
57#define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
58#define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
59#define ATMCI_MR_RDPROOF BIT(11) /* Read Proof */
60#define ATMCI_MR_WRPROOF BIT(12) /* Write Proof */
61#define ATMCI_MR_PDCFBYTE BIT(13) /* Force Byte Transfer */
62#define ATMCI_MR_PDCPADV BIT(14) /* Padding Value */
63#define ATMCI_MR_PDCMODE BIT(15) /* PDC-oriented Mode */
64#define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
65#define ATMCI_DTOR 0x0008 /* Data Timeout */
66#define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
67#define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
68#define ATMCI_SDCR 0x000c /* SD Card / SDIO */
69#define ATMCI_SDCSEL_SLOT_A (0 << 0) /* Select SD slot A */
70#define ATMCI_SDCSEL_SLOT_B (1 << 0) /* Select SD slot A */
71#define ATMCI_SDCSEL_MASK (3 << 0)
72#define ATMCI_SDCBUS_1BIT (0 << 6) /* 1-bit data bus */
73#define ATMCI_SDCBUS_4BIT (2 << 6) /* 4-bit data bus */
74#define ATMCI_SDCBUS_8BIT (3 << 6) /* 8-bit data bus[2] */
75#define ATMCI_SDCBUS_MASK (3 << 6)
76#define ATMCI_ARGR 0x0010 /* Command Argument */
77#define ATMCI_CMDR 0x0014 /* Command */
78#define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
79#define ATMCI_CMDR_RSPTYP_NONE (0 << 6) /* No response */
80#define ATMCI_CMDR_RSPTYP_48BIT (1 << 6) /* 48-bit response */
81#define ATMCI_CMDR_RSPTYP_136BIT (2 << 6) /* 136-bit response */
82#define ATMCI_CMDR_SPCMD_INIT (1 << 8) /* Initialization command */
83#define ATMCI_CMDR_SPCMD_SYNC (2 << 8) /* Synchronized command */
84#define ATMCI_CMDR_SPCMD_INT (4 << 8) /* Interrupt command */
85#define ATMCI_CMDR_SPCMD_INTRESP (5 << 8) /* Interrupt response */
86#define ATMCI_CMDR_OPDCMD (1 << 11) /* Open Drain */
87#define ATMCI_CMDR_MAXLAT_5CYC (0 << 12) /* Max latency 5 cycles */
88#define ATMCI_CMDR_MAXLAT_64CYC (1 << 12) /* Max latency 64 cycles */
89#define ATMCI_CMDR_START_XFER (1 << 16) /* Start data transfer */
90#define ATMCI_CMDR_STOP_XFER (2 << 16) /* Stop data transfer */
91#define ATMCI_CMDR_TRDIR_WRITE (0 << 18) /* Write data */
92#define ATMCI_CMDR_TRDIR_READ (1 << 18) /* Read data */
93#define ATMCI_CMDR_BLOCK (0 << 19) /* Single-block transfer */
94#define ATMCI_CMDR_MULTI_BLOCK (1 << 19) /* Multi-block transfer */
95#define ATMCI_CMDR_STREAM (2 << 19) /* MMC Stream transfer */
96#define ATMCI_CMDR_SDIO_BYTE (4 << 19) /* SDIO Byte transfer */
97#define ATMCI_CMDR_SDIO_BLOCK (5 << 19) /* SDIO Block transfer */
98#define ATMCI_CMDR_SDIO_SUSPEND (1 << 24) /* SDIO Suspend Command */
99#define ATMCI_CMDR_SDIO_RESUME (2 << 24) /* SDIO Resume Command */
100#define ATMCI_BLKR 0x0018 /* Block */
101#define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
102#define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
103#define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
104#define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
105#define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
106#define ATMCI_RSPR 0x0020 /* Response 0 */
107#define ATMCI_RSPR1 0x0024 /* Response 1 */
108#define ATMCI_RSPR2 0x0028 /* Response 2 */
109#define ATMCI_RSPR3 0x002c /* Response 3 */
110#define ATMCI_RDR 0x0030 /* Receive Data */
111#define ATMCI_TDR 0x0034 /* Transmit Data */
112#define ATMCI_SR 0x0040 /* Status */
113#define ATMCI_IER 0x0044 /* Interrupt Enable */
114#define ATMCI_IDR 0x0048 /* Interrupt Disable */
115#define ATMCI_IMR 0x004c /* Interrupt Mask */
116#define ATMCI_CMDRDY BIT(0) /* Command Ready */
117#define ATMCI_RXRDY BIT(1) /* Receiver Ready */
118#define ATMCI_TXRDY BIT(2) /* Transmitter Ready */
119#define ATMCI_BLKE BIT(3) /* Data Block Ended */
120#define ATMCI_DTIP BIT(4) /* Data Transfer In Progress */
121#define ATMCI_NOTBUSY BIT(5) /* Data Not Busy */
122#define ATMCI_ENDRX BIT(6) /* End of RX Buffer */
123#define ATMCI_ENDTX BIT(7) /* End of TX Buffer */
124#define ATMCI_SDIOIRQA BIT(8) /* SDIO IRQ in slot A */
125#define ATMCI_SDIOIRQB BIT(9) /* SDIO IRQ in slot B */
126#define ATMCI_SDIOWAIT BIT(12) /* SDIO Read Wait Operation Status */
127#define ATMCI_CSRCV BIT(13) /* CE-ATA Completion Signal Received */
128#define ATMCI_RXBUFF BIT(14) /* RX Buffer Full */
129#define ATMCI_TXBUFE BIT(15) /* TX Buffer Empty */
130#define ATMCI_RINDE BIT(16) /* Response Index Error */
131#define ATMCI_RDIRE BIT(17) /* Response Direction Error */
132#define ATMCI_RCRCE BIT(18) /* Response CRC Error */
133#define ATMCI_RENDE BIT(19) /* Response End Bit Error */
134#define ATMCI_RTOE BIT(20) /* Response Time-Out Error */
135#define ATMCI_DCRCE BIT(21) /* Data CRC Error */
136#define ATMCI_DTOE BIT(22) /* Data Time-Out Error */
137#define ATMCI_CSTOE BIT(23) /* Completion Signal Time-out Error */
138#define ATMCI_BLKOVRE BIT(24) /* DMA Block Overrun Error */
139#define ATMCI_DMADONE BIT(25) /* DMA Transfer Done */
140#define ATMCI_FIFOEMPTY BIT(26) /* FIFO Empty Flag */
141#define ATMCI_XFRDONE BIT(27) /* Transfer Done Flag */
142#define ATMCI_ACKRCV BIT(28) /* Boot Operation Acknowledge Received */
143#define ATMCI_ACKRCVE BIT(29) /* Boot Operation Acknowledge Error */
144#define ATMCI_OVRE BIT(30) /* RX Overrun Error */
145#define ATMCI_UNRE BIT(31) /* TX Underrun Error */
146#define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
147#define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
148#define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
149#define ATMCI_DMAEN BIT(8) /* DMA Hardware Handshaking Enable */
150#define ATMCI_CFG 0x0054 /* Configuration[2] */
151#define ATMCI_CFG_FIFOMODE_1DATA BIT(0) /* MCI Internal FIFO control mode */
152#define ATMCI_CFG_FERRCTRL_COR BIT(4) /* Flow Error flag reset control mode */
153#define ATMCI_CFG_HSMODE BIT(8) /* High Speed Mode */
154#define ATMCI_CFG_LSYNC BIT(12) /* Synchronize on the last block */
155#define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
156#define ATMCI_WP_EN BIT(0) /* WP Enable */
157#define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
158#define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
159#define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
160#define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
161#define ATMCI_VERSION 0x00FC /* Version */
162#define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
163
164/* This is not including the FIFO Aperture on MCI2 */
165#define ATMCI_REGS_SIZE 0x100
166
167/* Register access macros */
168#define atmci_readl(port, reg) \
169 __raw_readl((port)->regs + reg)
170#define atmci_writel(port, reg, value) \
171 __raw_writel((value), (port)->regs + reg)
172
173#define ATMCI_CMD_TIMEOUT_MS 2000
174#define AUTOSUSPEND_DELAY 50
175
176#define ATMCI_DATA_ERROR_FLAGS (ATMCI_DCRCE | ATMCI_DTOE | ATMCI_OVRE | ATMCI_UNRE)
177#define ATMCI_DMA_THRESHOLD 16
178
179enum {
180 EVENT_CMD_RDY = 0,
181 EVENT_XFER_COMPLETE,
182 EVENT_NOTBUSY,
183 EVENT_DATA_ERROR,
184};
185
186enum atmel_mci_state {
187 STATE_IDLE = 0,
188 STATE_SENDING_CMD,
189 STATE_DATA_XFER,
190 STATE_WAITING_NOTBUSY,
191 STATE_SENDING_STOP,
192 STATE_END_REQUEST,
193};
194
195enum atmci_xfer_dir {
196 XFER_RECEIVE = 0,
197 XFER_TRANSMIT,
198};
199
200enum atmci_pdc_buf {
201 PDC_FIRST_BUF = 0,
202 PDC_SECOND_BUF,
203};
204
205/**
206 * struct mci_slot_pdata - board-specific per-slot configuration
207 * @bus_width: Number of data lines wired up the slot
208 * @detect_pin: GPIO pin wired to the card detect switch
209 * @wp_pin: GPIO pin wired to the write protect sensor
210 * @non_removable: The slot is not removable, only detect once
211 *
212 * If a given slot is not present on the board, @bus_width should be
213 * set to 0. The other fields are ignored in this case.
214 *
215 * Any pins that aren't available should be set to a negative value.
216 *
217 * Note that support for multiple slots is experimental -- some cards
218 * might get upset if we don't get the clock management exactly right.
219 * But in most cases, it should work just fine.
220 */
221struct mci_slot_pdata {
222 unsigned int bus_width;
223 struct gpio_desc *detect_pin;
224 struct gpio_desc *wp_pin;
225 bool non_removable;
226};
227
228struct atmel_mci_caps {
229 bool has_dma_conf_reg;
230 bool has_pdc;
231 bool has_cfg_reg;
232 bool has_cstor_reg;
233 bool has_highspeed;
234 bool has_rwproof;
235 bool has_odd_clk_div;
236 bool has_bad_data_ordering;
237 bool need_reset_after_xfer;
238 bool need_blksz_mul_4;
239 bool need_notbusy_for_read_ops;
240};
241
242struct atmel_mci_dma {
243 struct dma_chan *chan;
244 struct dma_async_tx_descriptor *data_desc;
245};
246
247/**
248 * struct atmel_mci - MMC controller state shared between all slots
249 * @lock: Spinlock protecting the queue and associated data.
250 * @regs: Pointer to MMIO registers.
251 * @sg: Scatterlist entry currently being processed by PIO or PDC code.
252 * @sg_len: Size of the scatterlist
253 * @pio_offset: Offset into the current scatterlist entry.
254 * @buffer: Buffer used if we don't have the r/w proof capability. We
255 * don't have the time to switch pdc buffers so we have to use only
256 * one buffer for the full transaction.
257 * @buf_size: size of the buffer.
258 * @buf_phys_addr: buffer address needed for pdc.
259 * @cur_slot: The slot which is currently using the controller.
260 * @mrq: The request currently being processed on @cur_slot,
261 * or NULL if the controller is idle.
262 * @cmd: The command currently being sent to the card, or NULL.
263 * @data: The data currently being transferred, or NULL if no data
264 * transfer is in progress.
265 * @data_size: just data->blocks * data->blksz.
266 * @dma: DMA client state.
267 * @data_chan: DMA channel being used for the current data transfer.
268 * @dma_conf: Configuration for the DMA slave
269 * @cmd_status: Snapshot of SR taken upon completion of the current
270 * command. Only valid when EVENT_CMD_COMPLETE is pending.
271 * @data_status: Snapshot of SR taken upon completion of the current
272 * data transfer. Only valid when EVENT_DATA_COMPLETE or
273 * EVENT_DATA_ERROR is pending.
274 * @stop_cmdr: Value to be loaded into CMDR when the stop command is
275 * to be sent.
276 * @bh_work: Work running the request state machine.
277 * @pending_events: Bitmask of events flagged by the interrupt handler
278 * to be processed by the work.
279 * @completed_events: Bitmask of events which the state machine has
280 * processed.
281 * @state: Work state.
282 * @queue: List of slots waiting for access to the controller.
283 * @need_clock_update: Update the clock rate before the next request.
284 * @need_reset: Reset controller before next request.
285 * @timer: Timer to balance the data timeout error flag which cannot rise.
286 * @mode_reg: Value of the MR register.
287 * @cfg_reg: Value of the CFG register.
288 * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
289 * rate and timeout calculations.
290 * @mapbase: Physical address of the MMIO registers.
291 * @mck: The peripheral bus clock hooked up to the MMC controller.
292 * @dev: Device associated with the MMC controller.
293 * @pdata: Per-slot configuration data.
294 * @slot: Slots sharing this MMC controller.
295 * @caps: MCI capabilities depending on MCI version.
296 * @prepare_data: function to setup MCI before data transfer which
297 * depends on MCI capabilities.
298 * @submit_data: function to start data transfer which depends on MCI
299 * capabilities.
300 * @stop_transfer: function to stop data transfer which depends on MCI
301 * capabilities.
302 *
303 * Locking
304 * =======
305 *
306 * @lock is a softirq-safe spinlock protecting @queue as well as
307 * @cur_slot, @mrq and @state. These must always be updated
308 * at the same time while holding @lock.
309 *
310 * @lock also protects mode_reg and need_clock_update since these are
311 * used to synchronize mode register updates with the queue
312 * processing.
313 *
314 * The @mrq field of struct atmel_mci_slot is also protected by @lock,
315 * and must always be written at the same time as the slot is added to
316 * @queue.
317 *
318 * @pending_events and @completed_events are accessed using atomic bit
319 * operations, so they don't need any locking.
320 *
321 * None of the fields touched by the interrupt handler need any
322 * locking. However, ordering is important: Before EVENT_DATA_ERROR or
323 * EVENT_DATA_COMPLETE is set in @pending_events, all data-related
324 * interrupts must be disabled and @data_status updated with a
325 * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the
326 * CMDRDY interrupt must be disabled and @cmd_status updated with a
327 * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the
328 * bytes_xfered field of @data must be written. This is ensured by
329 * using barriers.
330 */
331struct atmel_mci {
332 spinlock_t lock;
333 void __iomem *regs;
334
335 struct scatterlist *sg;
336 unsigned int sg_len;
337 unsigned int pio_offset;
338 unsigned int *buffer;
339 unsigned int buf_size;
340 dma_addr_t buf_phys_addr;
341
342 struct atmel_mci_slot *cur_slot;
343 struct mmc_request *mrq;
344 struct mmc_command *cmd;
345 struct mmc_data *data;
346 unsigned int data_size;
347
348 struct atmel_mci_dma dma;
349 struct dma_chan *data_chan;
350 struct dma_slave_config dma_conf;
351
352 u32 cmd_status;
353 u32 data_status;
354 u32 stop_cmdr;
355
356 struct work_struct bh_work;
357 unsigned long pending_events;
358 unsigned long completed_events;
359 enum atmel_mci_state state;
360 struct list_head queue;
361
362 bool need_clock_update;
363 bool need_reset;
364 struct timer_list timer;
365 u32 mode_reg;
366 u32 cfg_reg;
367 unsigned long bus_hz;
368 unsigned long mapbase;
369 struct clk *mck;
370 struct device *dev;
371
372 struct mci_slot_pdata pdata[ATMCI_MAX_NR_SLOTS];
373 struct atmel_mci_slot *slot[ATMCI_MAX_NR_SLOTS];
374
375 struct atmel_mci_caps caps;
376
377 u32 (*prepare_data)(struct atmel_mci *host, struct mmc_data *data);
378 void (*submit_data)(struct atmel_mci *host, struct mmc_data *data);
379 void (*stop_transfer)(struct atmel_mci *host);
380};
381
382/**
383 * struct atmel_mci_slot - MMC slot state
384 * @mmc: The mmc_host representing this slot.
385 * @host: The MMC controller this slot is using.
386 * @sdc_reg: Value of SDCR to be written before using this slot.
387 * @sdio_irq: SDIO irq mask for this slot.
388 * @mrq: mmc_request currently being processed or waiting to be
389 * processed, or NULL when the slot is idle.
390 * @queue_node: List node for placing this node in the @queue list of
391 * &struct atmel_mci.
392 * @clock: Clock rate configured by set_ios(). Protected by host->lock.
393 * @flags: Random state bits associated with the slot.
394 * @detect_pin: GPIO pin used for card detection, or negative if not
395 * available.
396 * @wp_pin: GPIO pin used for card write protect sending, or negative
397 * if not available.
398 * @detect_timer: Timer used for debouncing @detect_pin interrupts.
399 */
400struct atmel_mci_slot {
401 struct mmc_host *mmc;
402 struct atmel_mci *host;
403
404 u32 sdc_reg;
405 u32 sdio_irq;
406
407 struct mmc_request *mrq;
408 struct list_head queue_node;
409
410 unsigned int clock;
411 unsigned long flags;
412#define ATMCI_CARD_PRESENT 0
413#define ATMCI_CARD_NEED_INIT 1
414#define ATMCI_SHUTDOWN 2
415
416 struct gpio_desc *detect_pin;
417 struct gpio_desc *wp_pin;
418
419 struct timer_list detect_timer;
420};
421
422#define atmci_test_and_clear_pending(host, event) \
423 test_and_clear_bit(event, &host->pending_events)
424#define atmci_set_completed(host, event) \
425 set_bit(event, &host->completed_events)
426#define atmci_set_pending(host, event) \
427 set_bit(event, &host->pending_events)
428
429/*
430 * The debugfs stuff below is mostly optimized away when
431 * CONFIG_DEBUG_FS is not set.
432 */
433static int atmci_req_show(struct seq_file *s, void *v)
434{
435 struct atmel_mci_slot *slot = s->private;
436 struct mmc_request *mrq;
437 struct mmc_command *cmd;
438 struct mmc_command *stop;
439 struct mmc_data *data;
440
441 /* Make sure we get a consistent snapshot */
442 spin_lock_bh(&slot->host->lock);
443 mrq = slot->mrq;
444
445 if (mrq) {
446 cmd = mrq->cmd;
447 data = mrq->data;
448 stop = mrq->stop;
449
450 if (cmd)
451 seq_printf(s,
452 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
453 cmd->opcode, cmd->arg, cmd->flags,
454 cmd->resp[0], cmd->resp[1], cmd->resp[2],
455 cmd->resp[3], cmd->error);
456 if (data)
457 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
458 data->bytes_xfered, data->blocks,
459 data->blksz, data->flags, data->error);
460 if (stop)
461 seq_printf(s,
462 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
463 stop->opcode, stop->arg, stop->flags,
464 stop->resp[0], stop->resp[1], stop->resp[2],
465 stop->resp[3], stop->error);
466 }
467
468 spin_unlock_bh(&slot->host->lock);
469
470 return 0;
471}
472
473DEFINE_SHOW_ATTRIBUTE(atmci_req);
474
475static void atmci_show_status_reg(struct seq_file *s,
476 const char *regname, u32 value)
477{
478 static const char *sr_bit[] = {
479 [0] = "CMDRDY",
480 [1] = "RXRDY",
481 [2] = "TXRDY",
482 [3] = "BLKE",
483 [4] = "DTIP",
484 [5] = "NOTBUSY",
485 [6] = "ENDRX",
486 [7] = "ENDTX",
487 [8] = "SDIOIRQA",
488 [9] = "SDIOIRQB",
489 [12] = "SDIOWAIT",
490 [14] = "RXBUFF",
491 [15] = "TXBUFE",
492 [16] = "RINDE",
493 [17] = "RDIRE",
494 [18] = "RCRCE",
495 [19] = "RENDE",
496 [20] = "RTOE",
497 [21] = "DCRCE",
498 [22] = "DTOE",
499 [23] = "CSTOE",
500 [24] = "BLKOVRE",
501 [25] = "DMADONE",
502 [26] = "FIFOEMPTY",
503 [27] = "XFRDONE",
504 [30] = "OVRE",
505 [31] = "UNRE",
506 };
507 unsigned int i;
508
509 seq_printf(s, "%s:\t0x%08x", regname, value);
510 for (i = 0; i < ARRAY_SIZE(sr_bit); i++) {
511 if (value & (1 << i)) {
512 if (sr_bit[i])
513 seq_printf(s, " %s", sr_bit[i]);
514 else
515 seq_puts(s, " UNKNOWN");
516 }
517 }
518 seq_putc(s, '\n');
519}
520
521static int atmci_regs_show(struct seq_file *s, void *v)
522{
523 struct atmel_mci *host = s->private;
524 struct device *dev = host->dev;
525 u32 *buf;
526 int ret = 0;
527
528
529 buf = kmalloc(ATMCI_REGS_SIZE, GFP_KERNEL);
530 if (!buf)
531 return -ENOMEM;
532
533 pm_runtime_get_sync(dev);
534
535 /*
536 * Grab a more or less consistent snapshot. Note that we're
537 * not disabling interrupts, so IMR and SR may not be
538 * consistent.
539 */
540 spin_lock_bh(&host->lock);
541 memcpy_fromio(buf, host->regs, ATMCI_REGS_SIZE);
542 spin_unlock_bh(&host->lock);
543
544 pm_runtime_mark_last_busy(dev);
545 pm_runtime_put_autosuspend(dev);
546
547 seq_printf(s, "MR:\t0x%08x%s%s ",
548 buf[ATMCI_MR / 4],
549 buf[ATMCI_MR / 4] & ATMCI_MR_RDPROOF ? " RDPROOF" : "",
550 buf[ATMCI_MR / 4] & ATMCI_MR_WRPROOF ? " WRPROOF" : "");
551 if (host->caps.has_odd_clk_div)
552 seq_printf(s, "{CLKDIV,CLKODD}=%u\n",
553 ((buf[ATMCI_MR / 4] & 0xff) << 1)
554 | ((buf[ATMCI_MR / 4] >> 16) & 1));
555 else
556 seq_printf(s, "CLKDIV=%u\n",
557 (buf[ATMCI_MR / 4] & 0xff));
558 seq_printf(s, "DTOR:\t0x%08x\n", buf[ATMCI_DTOR / 4]);
559 seq_printf(s, "SDCR:\t0x%08x\n", buf[ATMCI_SDCR / 4]);
560 seq_printf(s, "ARGR:\t0x%08x\n", buf[ATMCI_ARGR / 4]);
561 seq_printf(s, "BLKR:\t0x%08x BCNT=%u BLKLEN=%u\n",
562 buf[ATMCI_BLKR / 4],
563 buf[ATMCI_BLKR / 4] & 0xffff,
564 (buf[ATMCI_BLKR / 4] >> 16) & 0xffff);
565 if (host->caps.has_cstor_reg)
566 seq_printf(s, "CSTOR:\t0x%08x\n", buf[ATMCI_CSTOR / 4]);
567
568 /* Don't read RSPR and RDR; it will consume the data there */
569
570 atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]);
571 atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]);
572
573 if (host->caps.has_dma_conf_reg) {
574 u32 val;
575
576 val = buf[ATMCI_DMA / 4];
577 seq_printf(s, "DMA:\t0x%08x OFFSET=%u CHKSIZE=%u%s\n",
578 val, val & 3,
579 ((val >> 4) & 3) ?
580 1 << (((val >> 4) & 3) + 1) : 1,
581 val & ATMCI_DMAEN ? " DMAEN" : "");
582 }
583 if (host->caps.has_cfg_reg) {
584 u32 val;
585
586 val = buf[ATMCI_CFG / 4];
587 seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n",
588 val,
589 val & ATMCI_CFG_FIFOMODE_1DATA ? " FIFOMODE_ONE_DATA" : "",
590 val & ATMCI_CFG_FERRCTRL_COR ? " FERRCTRL_CLEAR_ON_READ" : "",
591 val & ATMCI_CFG_HSMODE ? " HSMODE" : "",
592 val & ATMCI_CFG_LSYNC ? " LSYNC" : "");
593 }
594
595 kfree(buf);
596
597 return ret;
598}
599
600DEFINE_SHOW_ATTRIBUTE(atmci_regs);
601
602static void atmci_init_debugfs(struct atmel_mci_slot *slot)
603{
604 struct mmc_host *mmc = slot->mmc;
605 struct atmel_mci *host = slot->host;
606 struct dentry *root;
607
608 root = mmc->debugfs_root;
609 if (!root)
610 return;
611
612 debugfs_create_file("regs", S_IRUSR, root, host, &atmci_regs_fops);
613 debugfs_create_file("req", S_IRUSR, root, slot, &atmci_req_fops);
614 debugfs_create_u32("state", S_IRUSR, root, &host->state);
615 debugfs_create_xul("pending_events", S_IRUSR, root,
616 &host->pending_events);
617 debugfs_create_xul("completed_events", S_IRUSR, root,
618 &host->completed_events);
619}
620
621static const struct of_device_id atmci_dt_ids[] = {
622 { .compatible = "atmel,hsmci" },
623 { /* sentinel */ }
624};
625
626MODULE_DEVICE_TABLE(of, atmci_dt_ids);
627
628static int atmci_of_init(struct atmel_mci *host)
629{
630 struct device *dev = host->dev;
631 struct device_node *np = dev->of_node;
632 struct device_node *cnp;
633 u32 slot_id;
634 int err;
635
636 if (!np)
637 return dev_err_probe(dev, -EINVAL, "device node not found\n");
638
639 for_each_child_of_node(np, cnp) {
640 if (of_property_read_u32(cnp, "reg", &slot_id)) {
641 dev_warn(dev, "reg property is missing for %pOF\n", cnp);
642 continue;
643 }
644
645 if (slot_id >= ATMCI_MAX_NR_SLOTS) {
646 dev_warn(dev, "can't have more than %d slots\n",
647 ATMCI_MAX_NR_SLOTS);
648 of_node_put(cnp);
649 break;
650 }
651
652 if (of_property_read_u32(cnp, "bus-width",
653 &host->pdata[slot_id].bus_width))
654 host->pdata[slot_id].bus_width = 1;
655
656 host->pdata[slot_id].detect_pin =
657 devm_fwnode_gpiod_get(dev, of_fwnode_handle(cnp),
658 "cd", GPIOD_IN, "cd-gpios");
659 err = PTR_ERR_OR_ZERO(host->pdata[slot_id].detect_pin);
660 if (err) {
661 if (err != -ENOENT) {
662 of_node_put(cnp);
663 return err;
664 }
665 host->pdata[slot_id].detect_pin = NULL;
666 }
667
668 host->pdata[slot_id].non_removable =
669 of_property_read_bool(cnp, "non-removable");
670
671 host->pdata[slot_id].wp_pin =
672 devm_fwnode_gpiod_get(dev, of_fwnode_handle(cnp),
673 "wp", GPIOD_IN, "wp-gpios");
674 err = PTR_ERR_OR_ZERO(host->pdata[slot_id].wp_pin);
675 if (err) {
676 if (err != -ENOENT) {
677 of_node_put(cnp);
678 return err;
679 }
680 host->pdata[slot_id].wp_pin = NULL;
681 }
682 }
683
684 return 0;
685}
686
687static inline unsigned int atmci_get_version(struct atmel_mci *host)
688{
689 return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
690}
691
692/*
693 * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
694 * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
695 * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
696 * 8 -> 3, 16 -> 4.
697 *
698 * This can be done by finding most significant bit set.
699 */
700static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
701 unsigned int maxburst)
702{
703 unsigned int version = atmci_get_version(host);
704 unsigned int offset = 2;
705
706 if (version >= 0x600)
707 offset = 1;
708
709 if (maxburst > 1)
710 return fls(maxburst) - offset;
711 else
712 return 0;
713}
714
715static void atmci_timeout_timer(struct timer_list *t)
716{
717 struct atmel_mci *host = from_timer(host, t, timer);
718 struct device *dev = host->dev;
719
720 dev_dbg(dev, "software timeout\n");
721
722 if (host->mrq->cmd->data) {
723 host->mrq->cmd->data->error = -ETIMEDOUT;
724 host->data = NULL;
725 /*
726 * With some SDIO modules, sometimes DMA transfer hangs. If
727 * stop_transfer() is not called then the DMA request is not
728 * removed, following ones are queued and never computed.
729 */
730 if (host->state == STATE_DATA_XFER)
731 host->stop_transfer(host);
732 } else {
733 host->mrq->cmd->error = -ETIMEDOUT;
734 host->cmd = NULL;
735 }
736 host->need_reset = 1;
737 host->state = STATE_END_REQUEST;
738 smp_wmb();
739 queue_work(system_bh_wq, &host->bh_work);
740}
741
742static inline unsigned int atmci_ns_to_clocks(struct atmel_mci *host,
743 unsigned int ns)
744{
745 /*
746 * It is easier here to use us instead of ns for the timeout,
747 * it prevents from overflows during calculation.
748 */
749 unsigned int us = DIV_ROUND_UP(ns, 1000);
750
751 /* Maximum clock frequency is host->bus_hz/2 */
752 return us * (DIV_ROUND_UP(host->bus_hz, 2000000));
753}
754
755static void atmci_set_timeout(struct atmel_mci *host,
756 struct atmel_mci_slot *slot, struct mmc_data *data)
757{
758 static unsigned dtomul_to_shift[] = {
759 0, 4, 7, 8, 10, 12, 16, 20
760 };
761 unsigned timeout;
762 unsigned dtocyc;
763 unsigned dtomul;
764
765 timeout = atmci_ns_to_clocks(host, data->timeout_ns)
766 + data->timeout_clks;
767
768 for (dtomul = 0; dtomul < 8; dtomul++) {
769 unsigned shift = dtomul_to_shift[dtomul];
770 dtocyc = (timeout + (1 << shift) - 1) >> shift;
771 if (dtocyc < 15)
772 break;
773 }
774
775 if (dtomul >= 8) {
776 dtomul = 7;
777 dtocyc = 15;
778 }
779
780 dev_vdbg(&slot->mmc->class_dev, "setting timeout to %u cycles\n",
781 dtocyc << dtomul_to_shift[dtomul]);
782 atmci_writel(host, ATMCI_DTOR, (ATMCI_DTOMUL(dtomul) | ATMCI_DTOCYC(dtocyc)));
783}
784
785/*
786 * Return mask with command flags to be enabled for this command.
787 */
788static u32 atmci_prepare_command(struct mmc_host *mmc,
789 struct mmc_command *cmd)
790{
791 struct mmc_data *data;
792 u32 cmdr;
793
794 cmd->error = -EINPROGRESS;
795
796 cmdr = ATMCI_CMDR_CMDNB(cmd->opcode);
797
798 if (cmd->flags & MMC_RSP_PRESENT) {
799 if (cmd->flags & MMC_RSP_136)
800 cmdr |= ATMCI_CMDR_RSPTYP_136BIT;
801 else
802 cmdr |= ATMCI_CMDR_RSPTYP_48BIT;
803 }
804
805 /*
806 * This should really be MAXLAT_5 for CMD2 and ACMD41, but
807 * it's too difficult to determine whether this is an ACMD or
808 * not. Better make it 64.
809 */
810 cmdr |= ATMCI_CMDR_MAXLAT_64CYC;
811
812 if (mmc->ios.bus_mode == MMC_BUSMODE_OPENDRAIN)
813 cmdr |= ATMCI_CMDR_OPDCMD;
814
815 data = cmd->data;
816 if (data) {
817 cmdr |= ATMCI_CMDR_START_XFER;
818
819 if (cmd->opcode == SD_IO_RW_EXTENDED) {
820 cmdr |= ATMCI_CMDR_SDIO_BLOCK;
821 } else {
822 if (data->blocks > 1)
823 cmdr |= ATMCI_CMDR_MULTI_BLOCK;
824 else
825 cmdr |= ATMCI_CMDR_BLOCK;
826 }
827
828 if (data->flags & MMC_DATA_READ)
829 cmdr |= ATMCI_CMDR_TRDIR_READ;
830 }
831
832 return cmdr;
833}
834
835static void atmci_send_command(struct atmel_mci *host,
836 struct mmc_command *cmd, u32 cmd_flags)
837{
838 struct device *dev = host->dev;
839 unsigned int timeout_ms = cmd->busy_timeout ? cmd->busy_timeout :
840 ATMCI_CMD_TIMEOUT_MS;
841
842 WARN_ON(host->cmd);
843 host->cmd = cmd;
844
845 dev_vdbg(dev, "start command: ARGR=0x%08x CMDR=0x%08x\n", cmd->arg, cmd_flags);
846
847 atmci_writel(host, ATMCI_ARGR, cmd->arg);
848 atmci_writel(host, ATMCI_CMDR, cmd_flags);
849
850 mod_timer(&host->timer, jiffies + msecs_to_jiffies(timeout_ms));
851}
852
853static void atmci_send_stop_cmd(struct atmel_mci *host, struct mmc_data *data)
854{
855 struct device *dev = host->dev;
856
857 dev_dbg(dev, "send stop command\n");
858 atmci_send_command(host, data->stop, host->stop_cmdr);
859 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
860}
861
862/*
863 * Configure given PDC buffer taking care of alignment issues.
864 * Update host->data_size and host->sg.
865 */
866static void atmci_pdc_set_single_buf(struct atmel_mci *host,
867 enum atmci_xfer_dir dir, enum atmci_pdc_buf buf_nb)
868{
869 u32 pointer_reg, counter_reg;
870 unsigned int buf_size;
871
872 if (dir == XFER_RECEIVE) {
873 pointer_reg = ATMEL_PDC_RPR;
874 counter_reg = ATMEL_PDC_RCR;
875 } else {
876 pointer_reg = ATMEL_PDC_TPR;
877 counter_reg = ATMEL_PDC_TCR;
878 }
879
880 if (buf_nb == PDC_SECOND_BUF) {
881 pointer_reg += ATMEL_PDC_SCND_BUF_OFF;
882 counter_reg += ATMEL_PDC_SCND_BUF_OFF;
883 }
884
885 if (!host->caps.has_rwproof) {
886 buf_size = host->buf_size;
887 atmci_writel(host, pointer_reg, host->buf_phys_addr);
888 } else {
889 buf_size = sg_dma_len(host->sg);
890 atmci_writel(host, pointer_reg, sg_dma_address(host->sg));
891 }
892
893 if (host->data_size <= buf_size) {
894 if (host->data_size & 0x3) {
895 /* If size is different from modulo 4, transfer bytes */
896 atmci_writel(host, counter_reg, host->data_size);
897 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCFBYTE);
898 } else {
899 /* Else transfer 32-bits words */
900 atmci_writel(host, counter_reg, host->data_size / 4);
901 }
902 host->data_size = 0;
903 } else {
904 /* We assume the size of a page is 32-bits aligned */
905 atmci_writel(host, counter_reg, sg_dma_len(host->sg) / 4);
906 host->data_size -= sg_dma_len(host->sg);
907 if (host->data_size)
908 host->sg = sg_next(host->sg);
909 }
910}
911
912/*
913 * Configure PDC buffer according to the data size ie configuring one or two
914 * buffers. Don't use this function if you want to configure only the second
915 * buffer. In this case, use atmci_pdc_set_single_buf.
916 */
917static void atmci_pdc_set_both_buf(struct atmel_mci *host, int dir)
918{
919 atmci_pdc_set_single_buf(host, dir, PDC_FIRST_BUF);
920 if (host->data_size)
921 atmci_pdc_set_single_buf(host, dir, PDC_SECOND_BUF);
922}
923
924/*
925 * Unmap sg lists, called when transfer is finished.
926 */
927static void atmci_pdc_cleanup(struct atmel_mci *host)
928{
929 struct mmc_data *data = host->data;
930 struct device *dev = host->dev;
931
932 if (data)
933 dma_unmap_sg(dev, data->sg, data->sg_len, mmc_get_dma_dir(data));
934}
935
936/*
937 * Disable PDC transfers. Update pending flags to EVENT_XFER_COMPLETE after
938 * having received ATMCI_TXBUFE or ATMCI_RXBUFF interrupt. Enable ATMCI_NOTBUSY
939 * interrupt needed for both transfer directions.
940 */
941static void atmci_pdc_complete(struct atmel_mci *host)
942{
943 struct device *dev = host->dev;
944 int transfer_size = host->data->blocks * host->data->blksz;
945 int i;
946
947 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
948
949 if ((!host->caps.has_rwproof)
950 && (host->data->flags & MMC_DATA_READ)) {
951 if (host->caps.has_bad_data_ordering)
952 for (i = 0; i < transfer_size; i++)
953 host->buffer[i] = swab32(host->buffer[i]);
954 sg_copy_from_buffer(host->data->sg, host->data->sg_len,
955 host->buffer, transfer_size);
956 }
957
958 atmci_pdc_cleanup(host);
959
960 dev_dbg(dev, "(%s) set pending xfer complete\n", __func__);
961 atmci_set_pending(host, EVENT_XFER_COMPLETE);
962 queue_work(system_bh_wq, &host->bh_work);
963}
964
965static void atmci_dma_cleanup(struct atmel_mci *host)
966{
967 struct mmc_data *data = host->data;
968
969 if (data)
970 dma_unmap_sg(host->dma.chan->device->dev,
971 data->sg, data->sg_len,
972 mmc_get_dma_dir(data));
973}
974
975/*
976 * This function is called by the DMA driver from bh context.
977 */
978static void atmci_dma_complete(void *arg)
979{
980 struct atmel_mci *host = arg;
981 struct mmc_data *data = host->data;
982 struct device *dev = host->dev;
983
984 dev_vdbg(dev, "DMA complete\n");
985
986 if (host->caps.has_dma_conf_reg)
987 /* Disable DMA hardware handshaking on MCI */
988 atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN);
989
990 atmci_dma_cleanup(host);
991
992 /*
993 * If the card was removed, data will be NULL. No point trying
994 * to send the stop command or waiting for NBUSY in this case.
995 */
996 if (data) {
997 dev_dbg(dev, "(%s) set pending xfer complete\n", __func__);
998 atmci_set_pending(host, EVENT_XFER_COMPLETE);
999 queue_work(system_bh_wq, &host->bh_work);
1000
1001 /*
1002 * Regardless of what the documentation says, we have
1003 * to wait for NOTBUSY even after block read
1004 * operations.
1005 *
1006 * When the DMA transfer is complete, the controller
1007 * may still be reading the CRC from the card, i.e.
1008 * the data transfer is still in progress and we
1009 * haven't seen all the potential error bits yet.
1010 *
1011 * The interrupt handler will schedule a different
1012 * bh work to finish things up when the data transfer
1013 * is completely done.
1014 *
1015 * We may not complete the mmc request here anyway
1016 * because the mmc layer may call back and cause us to
1017 * violate the "don't submit new operations from the
1018 * completion callback" rule of the dma engine
1019 * framework.
1020 */
1021 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1022 }
1023}
1024
1025/*
1026 * Returns a mask of interrupt flags to be enabled after the whole
1027 * request has been prepared.
1028 */
1029static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
1030{
1031 u32 iflags;
1032
1033 data->error = -EINPROGRESS;
1034
1035 host->sg = data->sg;
1036 host->sg_len = data->sg_len;
1037 host->data = data;
1038 host->data_chan = NULL;
1039
1040 iflags = ATMCI_DATA_ERROR_FLAGS;
1041
1042 /*
1043 * Errata: MMC data write operation with less than 12
1044 * bytes is impossible.
1045 *
1046 * Errata: MCI Transmit Data Register (TDR) FIFO
1047 * corruption when length is not multiple of 4.
1048 */
1049 if (data->blocks * data->blksz < 12
1050 || (data->blocks * data->blksz) & 3)
1051 host->need_reset = true;
1052
1053 host->pio_offset = 0;
1054 if (data->flags & MMC_DATA_READ)
1055 iflags |= ATMCI_RXRDY;
1056 else
1057 iflags |= ATMCI_TXRDY;
1058
1059 return iflags;
1060}
1061
1062/*
1063 * Set interrupt flags and set block length into the MCI mode register even
1064 * if this value is also accessible in the MCI block register. It seems to be
1065 * necessary before the High Speed MCI version. It also map sg and configure
1066 * PDC registers.
1067 */
1068static u32
1069atmci_prepare_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1070{
1071 struct device *dev = host->dev;
1072 u32 iflags, tmp;
1073 int i;
1074
1075 data->error = -EINPROGRESS;
1076
1077 host->data = data;
1078 host->sg = data->sg;
1079 iflags = ATMCI_DATA_ERROR_FLAGS;
1080
1081 /* Enable pdc mode */
1082 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCMODE);
1083
1084 if (data->flags & MMC_DATA_READ)
1085 iflags |= ATMCI_ENDRX | ATMCI_RXBUFF;
1086 else
1087 iflags |= ATMCI_ENDTX | ATMCI_TXBUFE | ATMCI_BLKE;
1088
1089 /* Set BLKLEN */
1090 tmp = atmci_readl(host, ATMCI_MR);
1091 tmp &= 0x0000ffff;
1092 tmp |= ATMCI_BLKLEN(data->blksz);
1093 atmci_writel(host, ATMCI_MR, tmp);
1094
1095 /* Configure PDC */
1096 host->data_size = data->blocks * data->blksz;
1097 dma_map_sg(dev, data->sg, data->sg_len, mmc_get_dma_dir(data));
1098
1099 if ((!host->caps.has_rwproof)
1100 && (host->data->flags & MMC_DATA_WRITE)) {
1101 sg_copy_to_buffer(host->data->sg, host->data->sg_len,
1102 host->buffer, host->data_size);
1103 if (host->caps.has_bad_data_ordering)
1104 for (i = 0; i < host->data_size; i++)
1105 host->buffer[i] = swab32(host->buffer[i]);
1106 }
1107
1108 if (host->data_size)
1109 atmci_pdc_set_both_buf(host, data->flags & MMC_DATA_READ ?
1110 XFER_RECEIVE : XFER_TRANSMIT);
1111 return iflags;
1112}
1113
1114static u32
1115atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
1116{
1117 struct dma_chan *chan;
1118 struct dma_async_tx_descriptor *desc;
1119 struct scatterlist *sg;
1120 unsigned int i;
1121 enum dma_transfer_direction slave_dirn;
1122 unsigned int sglen;
1123 u32 maxburst;
1124 u32 iflags;
1125
1126 data->error = -EINPROGRESS;
1127
1128 WARN_ON(host->data);
1129 host->sg = NULL;
1130 host->data = data;
1131
1132 iflags = ATMCI_DATA_ERROR_FLAGS;
1133
1134 /*
1135 * We don't do DMA on "complex" transfers, i.e. with
1136 * non-word-aligned buffers or lengths. Also, we don't bother
1137 * with all the DMA setup overhead for short transfers.
1138 */
1139 if (data->blocks * data->blksz < ATMCI_DMA_THRESHOLD)
1140 return atmci_prepare_data(host, data);
1141 if (data->blksz & 3)
1142 return atmci_prepare_data(host, data);
1143
1144 for_each_sg(data->sg, sg, data->sg_len, i) {
1145 if (sg->offset & 3 || sg->length & 3)
1146 return atmci_prepare_data(host, data);
1147 }
1148
1149 /* If we don't have a channel, we can't do DMA */
1150 if (!host->dma.chan)
1151 return -ENODEV;
1152
1153 chan = host->dma.chan;
1154 host->data_chan = chan;
1155
1156 if (data->flags & MMC_DATA_READ) {
1157 host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
1158 maxburst = atmci_convert_chksize(host,
1159 host->dma_conf.src_maxburst);
1160 } else {
1161 host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
1162 maxburst = atmci_convert_chksize(host,
1163 host->dma_conf.dst_maxburst);
1164 }
1165
1166 if (host->caps.has_dma_conf_reg)
1167 atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) |
1168 ATMCI_DMAEN);
1169
1170 sglen = dma_map_sg(chan->device->dev, data->sg,
1171 data->sg_len, mmc_get_dma_dir(data));
1172
1173 dmaengine_slave_config(chan, &host->dma_conf);
1174 desc = dmaengine_prep_slave_sg(chan,
1175 data->sg, sglen, slave_dirn,
1176 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1177 if (!desc)
1178 goto unmap_exit;
1179
1180 host->dma.data_desc = desc;
1181 desc->callback = atmci_dma_complete;
1182 desc->callback_param = host;
1183
1184 return iflags;
1185unmap_exit:
1186 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len,
1187 mmc_get_dma_dir(data));
1188 return -ENOMEM;
1189}
1190
1191static void
1192atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
1193{
1194 return;
1195}
1196
1197/*
1198 * Start PDC according to transfer direction.
1199 */
1200static void
1201atmci_submit_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1202{
1203 if (data->flags & MMC_DATA_READ)
1204 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1205 else
1206 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1207}
1208
1209static void
1210atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
1211{
1212 struct dma_chan *chan = host->data_chan;
1213 struct dma_async_tx_descriptor *desc = host->dma.data_desc;
1214
1215 if (chan) {
1216 dmaengine_submit(desc);
1217 dma_async_issue_pending(chan);
1218 }
1219}
1220
1221static void atmci_stop_transfer(struct atmel_mci *host)
1222{
1223 struct device *dev = host->dev;
1224
1225 dev_dbg(dev, "(%s) set pending xfer complete\n", __func__);
1226 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1227 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1228}
1229
1230/*
1231 * Stop data transfer because error(s) occurred.
1232 */
1233static void atmci_stop_transfer_pdc(struct atmel_mci *host)
1234{
1235 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
1236}
1237
1238static void atmci_stop_transfer_dma(struct atmel_mci *host)
1239{
1240 struct dma_chan *chan = host->data_chan;
1241 struct device *dev = host->dev;
1242
1243 if (chan) {
1244 dmaengine_terminate_all(chan);
1245 atmci_dma_cleanup(host);
1246 } else {
1247 /* Data transfer was stopped by the interrupt handler */
1248 dev_dbg(dev, "(%s) set pending xfer complete\n", __func__);
1249 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1250 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1251 }
1252}
1253
1254/*
1255 * Start a request: prepare data if needed, prepare the command and activate
1256 * interrupts.
1257 */
1258static void atmci_start_request(struct atmel_mci *host,
1259 struct atmel_mci_slot *slot)
1260{
1261 struct device *dev = host->dev;
1262 struct mmc_request *mrq;
1263 struct mmc_command *cmd;
1264 struct mmc_data *data;
1265 u32 iflags;
1266 u32 cmdflags;
1267
1268 mrq = slot->mrq;
1269 host->cur_slot = slot;
1270 host->mrq = mrq;
1271
1272 host->pending_events = 0;
1273 host->completed_events = 0;
1274 host->cmd_status = 0;
1275 host->data_status = 0;
1276
1277 dev_dbg(dev, "start request: cmd %u\n", mrq->cmd->opcode);
1278
1279 if (host->need_reset || host->caps.need_reset_after_xfer) {
1280 iflags = atmci_readl(host, ATMCI_IMR);
1281 iflags &= (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB);
1282 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1283 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1284 atmci_writel(host, ATMCI_MR, host->mode_reg);
1285 if (host->caps.has_cfg_reg)
1286 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1287 atmci_writel(host, ATMCI_IER, iflags);
1288 host->need_reset = false;
1289 }
1290 atmci_writel(host, ATMCI_SDCR, slot->sdc_reg);
1291
1292 iflags = atmci_readl(host, ATMCI_IMR);
1293 if (iflags & ~(ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
1294 dev_dbg(&slot->mmc->class_dev, "WARNING: IMR=0x%08x\n",
1295 iflags);
1296
1297 if (unlikely(test_and_clear_bit(ATMCI_CARD_NEED_INIT, &slot->flags))) {
1298 /* Send init sequence (74 clock cycles) */
1299 atmci_writel(host, ATMCI_CMDR, ATMCI_CMDR_SPCMD_INIT);
1300 while (!(atmci_readl(host, ATMCI_SR) & ATMCI_CMDRDY))
1301 cpu_relax();
1302 }
1303 iflags = 0;
1304 data = mrq->data;
1305 if (data) {
1306 atmci_set_timeout(host, slot, data);
1307
1308 /* Must set block count/size before sending command */
1309 atmci_writel(host, ATMCI_BLKR, ATMCI_BCNT(data->blocks)
1310 | ATMCI_BLKLEN(data->blksz));
1311 dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n",
1312 ATMCI_BCNT(data->blocks) | ATMCI_BLKLEN(data->blksz));
1313
1314 iflags |= host->prepare_data(host, data);
1315 }
1316
1317 iflags |= ATMCI_CMDRDY;
1318 cmd = mrq->cmd;
1319 cmdflags = atmci_prepare_command(slot->mmc, cmd);
1320
1321 /*
1322 * DMA transfer should be started before sending the command to avoid
1323 * unexpected errors especially for read operations in SDIO mode.
1324 * Unfortunately, in PDC mode, command has to be sent before starting
1325 * the transfer.
1326 */
1327 if (host->submit_data != &atmci_submit_data_dma)
1328 atmci_send_command(host, cmd, cmdflags);
1329
1330 if (data)
1331 host->submit_data(host, data);
1332
1333 if (host->submit_data == &atmci_submit_data_dma)
1334 atmci_send_command(host, cmd, cmdflags);
1335
1336 if (mrq->stop) {
1337 host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop);
1338 host->stop_cmdr |= ATMCI_CMDR_STOP_XFER;
1339 if (!(data->flags & MMC_DATA_WRITE))
1340 host->stop_cmdr |= ATMCI_CMDR_TRDIR_READ;
1341 host->stop_cmdr |= ATMCI_CMDR_MULTI_BLOCK;
1342 }
1343
1344 /*
1345 * We could have enabled interrupts earlier, but I suspect
1346 * that would open up a nice can of interesting race
1347 * conditions (e.g. command and data complete, but stop not
1348 * prepared yet.)
1349 */
1350 atmci_writel(host, ATMCI_IER, iflags);
1351}
1352
1353static void atmci_queue_request(struct atmel_mci *host,
1354 struct atmel_mci_slot *slot, struct mmc_request *mrq)
1355{
1356 struct device *dev = host->dev;
1357
1358 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1359 host->state);
1360
1361 spin_lock_bh(&host->lock);
1362 slot->mrq = mrq;
1363 if (host->state == STATE_IDLE) {
1364 host->state = STATE_SENDING_CMD;
1365 atmci_start_request(host, slot);
1366 } else {
1367 dev_dbg(dev, "queue request\n");
1368 list_add_tail(&slot->queue_node, &host->queue);
1369 }
1370 spin_unlock_bh(&host->lock);
1371}
1372
1373static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1374{
1375 struct atmel_mci_slot *slot = mmc_priv(mmc);
1376 struct atmel_mci *host = slot->host;
1377 struct device *dev = host->dev;
1378 struct mmc_data *data;
1379
1380 WARN_ON(slot->mrq);
1381 dev_dbg(dev, "MRQ: cmd %u\n", mrq->cmd->opcode);
1382
1383 /*
1384 * We may "know" the card is gone even though there's still an
1385 * electrical connection. If so, we really need to communicate
1386 * this to the MMC core since there won't be any more
1387 * interrupts as the card is completely removed. Otherwise,
1388 * the MMC core might believe the card is still there even
1389 * though the card was just removed very slowly.
1390 */
1391 if (!test_bit(ATMCI_CARD_PRESENT, &slot->flags)) {
1392 mrq->cmd->error = -ENOMEDIUM;
1393 mmc_request_done(mmc, mrq);
1394 return;
1395 }
1396
1397 /* We don't support multiple blocks of weird lengths. */
1398 data = mrq->data;
1399 if (data && data->blocks > 1 && data->blksz & 3) {
1400 mrq->cmd->error = -EINVAL;
1401 mmc_request_done(mmc, mrq);
1402 }
1403
1404 atmci_queue_request(host, slot, mrq);
1405}
1406
1407static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1408{
1409 struct atmel_mci_slot *slot = mmc_priv(mmc);
1410 struct atmel_mci *host = slot->host;
1411 unsigned int i;
1412
1413 slot->sdc_reg &= ~ATMCI_SDCBUS_MASK;
1414 switch (ios->bus_width) {
1415 case MMC_BUS_WIDTH_1:
1416 slot->sdc_reg |= ATMCI_SDCBUS_1BIT;
1417 break;
1418 case MMC_BUS_WIDTH_4:
1419 slot->sdc_reg |= ATMCI_SDCBUS_4BIT;
1420 break;
1421 case MMC_BUS_WIDTH_8:
1422 slot->sdc_reg |= ATMCI_SDCBUS_8BIT;
1423 break;
1424 }
1425
1426 if (ios->clock) {
1427 unsigned int clock_min = ~0U;
1428 int clkdiv;
1429
1430 spin_lock_bh(&host->lock);
1431 if (!host->mode_reg) {
1432 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1433 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1434 if (host->caps.has_cfg_reg)
1435 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1436 }
1437
1438 /*
1439 * Use mirror of ios->clock to prevent race with mmc
1440 * core ios update when finding the minimum.
1441 */
1442 slot->clock = ios->clock;
1443 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1444 if (host->slot[i] && host->slot[i]->clock
1445 && host->slot[i]->clock < clock_min)
1446 clock_min = host->slot[i]->clock;
1447 }
1448
1449 /* Calculate clock divider */
1450 if (host->caps.has_odd_clk_div) {
1451 clkdiv = DIV_ROUND_UP(host->bus_hz, clock_min) - 2;
1452 if (clkdiv < 0) {
1453 dev_warn(&mmc->class_dev,
1454 "clock %u too fast; using %lu\n",
1455 clock_min, host->bus_hz / 2);
1456 clkdiv = 0;
1457 } else if (clkdiv > 511) {
1458 dev_warn(&mmc->class_dev,
1459 "clock %u too slow; using %lu\n",
1460 clock_min, host->bus_hz / (511 + 2));
1461 clkdiv = 511;
1462 }
1463 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv >> 1)
1464 | ATMCI_MR_CLKODD(clkdiv & 1);
1465 } else {
1466 clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * clock_min) - 1;
1467 if (clkdiv > 255) {
1468 dev_warn(&mmc->class_dev,
1469 "clock %u too slow; using %lu\n",
1470 clock_min, host->bus_hz / (2 * 256));
1471 clkdiv = 255;
1472 }
1473 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv);
1474 }
1475
1476 /*
1477 * WRPROOF and RDPROOF prevent overruns/underruns by
1478 * stopping the clock when the FIFO is full/empty.
1479 * This state is not expected to last for long.
1480 */
1481 if (host->caps.has_rwproof)
1482 host->mode_reg |= (ATMCI_MR_WRPROOF | ATMCI_MR_RDPROOF);
1483
1484 if (host->caps.has_cfg_reg) {
1485 /* setup High Speed mode in relation with card capacity */
1486 if (ios->timing == MMC_TIMING_SD_HS)
1487 host->cfg_reg |= ATMCI_CFG_HSMODE;
1488 else
1489 host->cfg_reg &= ~ATMCI_CFG_HSMODE;
1490 }
1491
1492 if (list_empty(&host->queue)) {
1493 atmci_writel(host, ATMCI_MR, host->mode_reg);
1494 if (host->caps.has_cfg_reg)
1495 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1496 } else {
1497 host->need_clock_update = true;
1498 }
1499
1500 spin_unlock_bh(&host->lock);
1501 } else {
1502 bool any_slot_active = false;
1503
1504 spin_lock_bh(&host->lock);
1505 slot->clock = 0;
1506 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1507 if (host->slot[i] && host->slot[i]->clock) {
1508 any_slot_active = true;
1509 break;
1510 }
1511 }
1512 if (!any_slot_active) {
1513 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
1514 if (host->mode_reg) {
1515 atmci_readl(host, ATMCI_MR);
1516 }
1517 host->mode_reg = 0;
1518 }
1519 spin_unlock_bh(&host->lock);
1520 }
1521
1522 switch (ios->power_mode) {
1523 case MMC_POWER_OFF:
1524 if (!IS_ERR(mmc->supply.vmmc))
1525 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1526 break;
1527 case MMC_POWER_UP:
1528 set_bit(ATMCI_CARD_NEED_INIT, &slot->flags);
1529 if (!IS_ERR(mmc->supply.vmmc))
1530 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
1531 break;
1532 default:
1533 break;
1534 }
1535}
1536
1537static int atmci_get_ro(struct mmc_host *mmc)
1538{
1539 int read_only = -ENOSYS;
1540 struct atmel_mci_slot *slot = mmc_priv(mmc);
1541
1542 if (slot->wp_pin) {
1543 read_only = gpiod_get_value(slot->wp_pin);
1544 dev_dbg(&mmc->class_dev, "card is %s\n",
1545 read_only ? "read-only" : "read-write");
1546 }
1547
1548 return read_only;
1549}
1550
1551static int atmci_get_cd(struct mmc_host *mmc)
1552{
1553 int present = -ENOSYS;
1554 struct atmel_mci_slot *slot = mmc_priv(mmc);
1555
1556 if (slot->detect_pin) {
1557 present = gpiod_get_value_cansleep(slot->detect_pin);
1558 dev_dbg(&mmc->class_dev, "card is %spresent\n",
1559 present ? "" : "not ");
1560 }
1561
1562 return present;
1563}
1564
1565static void atmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1566{
1567 struct atmel_mci_slot *slot = mmc_priv(mmc);
1568 struct atmel_mci *host = slot->host;
1569
1570 if (enable)
1571 atmci_writel(host, ATMCI_IER, slot->sdio_irq);
1572 else
1573 atmci_writel(host, ATMCI_IDR, slot->sdio_irq);
1574}
1575
1576static const struct mmc_host_ops atmci_ops = {
1577 .request = atmci_request,
1578 .set_ios = atmci_set_ios,
1579 .get_ro = atmci_get_ro,
1580 .get_cd = atmci_get_cd,
1581 .enable_sdio_irq = atmci_enable_sdio_irq,
1582};
1583
1584/* Called with host->lock held */
1585static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq)
1586 __releases(&host->lock)
1587 __acquires(&host->lock)
1588{
1589 struct atmel_mci_slot *slot = NULL;
1590 struct mmc_host *prev_mmc = host->cur_slot->mmc;
1591 struct device *dev = host->dev;
1592
1593 WARN_ON(host->cmd || host->data);
1594
1595 del_timer(&host->timer);
1596
1597 /*
1598 * Update the MMC clock rate if necessary. This may be
1599 * necessary if set_ios() is called when a different slot is
1600 * busy transferring data.
1601 */
1602 if (host->need_clock_update) {
1603 atmci_writel(host, ATMCI_MR, host->mode_reg);
1604 if (host->caps.has_cfg_reg)
1605 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1606 }
1607
1608 host->cur_slot->mrq = NULL;
1609 host->mrq = NULL;
1610 if (!list_empty(&host->queue)) {
1611 slot = list_entry(host->queue.next,
1612 struct atmel_mci_slot, queue_node);
1613 list_del(&slot->queue_node);
1614 dev_vdbg(dev, "list not empty: %s is next\n", mmc_hostname(slot->mmc));
1615 host->state = STATE_SENDING_CMD;
1616 atmci_start_request(host, slot);
1617 } else {
1618 dev_vdbg(dev, "list empty\n");
1619 host->state = STATE_IDLE;
1620 }
1621
1622 spin_unlock(&host->lock);
1623 mmc_request_done(prev_mmc, mrq);
1624 spin_lock(&host->lock);
1625}
1626
1627static void atmci_command_complete(struct atmel_mci *host,
1628 struct mmc_command *cmd)
1629{
1630 u32 status = host->cmd_status;
1631
1632 /* Read the response from the card (up to 16 bytes) */
1633 cmd->resp[0] = atmci_readl(host, ATMCI_RSPR);
1634 cmd->resp[1] = atmci_readl(host, ATMCI_RSPR);
1635 cmd->resp[2] = atmci_readl(host, ATMCI_RSPR);
1636 cmd->resp[3] = atmci_readl(host, ATMCI_RSPR);
1637
1638 if (status & ATMCI_RTOE)
1639 cmd->error = -ETIMEDOUT;
1640 else if ((cmd->flags & MMC_RSP_CRC) && (status & ATMCI_RCRCE))
1641 cmd->error = -EILSEQ;
1642 else if (status & (ATMCI_RINDE | ATMCI_RDIRE | ATMCI_RENDE))
1643 cmd->error = -EIO;
1644 else if (host->mrq->data && (host->mrq->data->blksz & 3)) {
1645 if (host->caps.need_blksz_mul_4) {
1646 cmd->error = -EINVAL;
1647 host->need_reset = 1;
1648 }
1649 } else
1650 cmd->error = 0;
1651}
1652
1653static void atmci_detect_change(struct timer_list *t)
1654{
1655 struct atmel_mci_slot *slot = from_timer(slot, t, detect_timer);
1656 bool present;
1657 bool present_old;
1658
1659 /*
1660 * atmci_cleanup_slot() sets the ATMCI_SHUTDOWN flag before
1661 * freeing the interrupt. We must not re-enable the interrupt
1662 * if it has been freed, and if we're shutting down, it
1663 * doesn't really matter whether the card is present or not.
1664 */
1665 smp_rmb();
1666 if (test_bit(ATMCI_SHUTDOWN, &slot->flags))
1667 return;
1668
1669 enable_irq(gpiod_to_irq(slot->detect_pin));
1670 present = gpiod_get_value_cansleep(slot->detect_pin);
1671 present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
1672
1673 dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
1674 present, present_old);
1675
1676 if (present != present_old) {
1677 struct atmel_mci *host = slot->host;
1678 struct mmc_request *mrq;
1679
1680 dev_dbg(&slot->mmc->class_dev, "card %s\n",
1681 present ? "inserted" : "removed");
1682
1683 spin_lock(&host->lock);
1684
1685 if (!present)
1686 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
1687 else
1688 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
1689
1690 /* Clean up queue if present */
1691 mrq = slot->mrq;
1692 if (mrq) {
1693 if (mrq == host->mrq) {
1694 /*
1695 * Reset controller to terminate any ongoing
1696 * commands or data transfers.
1697 */
1698 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1699 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1700 atmci_writel(host, ATMCI_MR, host->mode_reg);
1701 if (host->caps.has_cfg_reg)
1702 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1703
1704 host->data = NULL;
1705 host->cmd = NULL;
1706
1707 switch (host->state) {
1708 case STATE_IDLE:
1709 break;
1710 case STATE_SENDING_CMD:
1711 mrq->cmd->error = -ENOMEDIUM;
1712 if (mrq->data)
1713 host->stop_transfer(host);
1714 break;
1715 case STATE_DATA_XFER:
1716 mrq->data->error = -ENOMEDIUM;
1717 host->stop_transfer(host);
1718 break;
1719 case STATE_WAITING_NOTBUSY:
1720 mrq->data->error = -ENOMEDIUM;
1721 break;
1722 case STATE_SENDING_STOP:
1723 mrq->stop->error = -ENOMEDIUM;
1724 break;
1725 case STATE_END_REQUEST:
1726 break;
1727 }
1728
1729 atmci_request_end(host, mrq);
1730 } else {
1731 list_del(&slot->queue_node);
1732 mrq->cmd->error = -ENOMEDIUM;
1733 if (mrq->data)
1734 mrq->data->error = -ENOMEDIUM;
1735 if (mrq->stop)
1736 mrq->stop->error = -ENOMEDIUM;
1737
1738 spin_unlock(&host->lock);
1739 mmc_request_done(slot->mmc, mrq);
1740 spin_lock(&host->lock);
1741 }
1742 }
1743 spin_unlock(&host->lock);
1744
1745 mmc_detect_change(slot->mmc, 0);
1746 }
1747}
1748
1749static void atmci_work_func(struct work_struct *t)
1750{
1751 struct atmel_mci *host = from_work(host, t, bh_work);
1752 struct mmc_request *mrq = host->mrq;
1753 struct mmc_data *data = host->data;
1754 struct device *dev = host->dev;
1755 enum atmel_mci_state state = host->state;
1756 enum atmel_mci_state prev_state;
1757 u32 status;
1758
1759 spin_lock(&host->lock);
1760
1761 state = host->state;
1762
1763 dev_vdbg(dev, "bh_work: state %u pending/completed/mask %lx/%lx/%x\n",
1764 state, host->pending_events, host->completed_events,
1765 atmci_readl(host, ATMCI_IMR));
1766
1767 do {
1768 prev_state = state;
1769 dev_dbg(dev, "FSM: state=%d\n", state);
1770
1771 switch (state) {
1772 case STATE_IDLE:
1773 break;
1774
1775 case STATE_SENDING_CMD:
1776 /*
1777 * Command has been sent, we are waiting for command
1778 * ready. Then we have three next states possible:
1779 * END_REQUEST by default, WAITING_NOTBUSY if it's a
1780 * command needing it or DATA_XFER if there is data.
1781 */
1782 dev_dbg(dev, "FSM: cmd ready?\n");
1783 if (!atmci_test_and_clear_pending(host,
1784 EVENT_CMD_RDY))
1785 break;
1786
1787 dev_dbg(dev, "set completed cmd ready\n");
1788 host->cmd = NULL;
1789 atmci_set_completed(host, EVENT_CMD_RDY);
1790 atmci_command_complete(host, mrq->cmd);
1791 if (mrq->data) {
1792 dev_dbg(dev, "command with data transfer\n");
1793 /*
1794 * If there is a command error don't start
1795 * data transfer.
1796 */
1797 if (mrq->cmd->error) {
1798 host->stop_transfer(host);
1799 host->data = NULL;
1800 atmci_writel(host, ATMCI_IDR,
1801 ATMCI_TXRDY | ATMCI_RXRDY
1802 | ATMCI_DATA_ERROR_FLAGS);
1803 state = STATE_END_REQUEST;
1804 } else
1805 state = STATE_DATA_XFER;
1806 } else if ((!mrq->data) && (mrq->cmd->flags & MMC_RSP_BUSY)) {
1807 dev_dbg(dev, "command response need waiting notbusy\n");
1808 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1809 state = STATE_WAITING_NOTBUSY;
1810 } else
1811 state = STATE_END_REQUEST;
1812
1813 break;
1814
1815 case STATE_DATA_XFER:
1816 if (atmci_test_and_clear_pending(host,
1817 EVENT_DATA_ERROR)) {
1818 dev_dbg(dev, "set completed data error\n");
1819 atmci_set_completed(host, EVENT_DATA_ERROR);
1820 state = STATE_END_REQUEST;
1821 break;
1822 }
1823
1824 /*
1825 * A data transfer is in progress. The event expected
1826 * to move to the next state depends of data transfer
1827 * type (PDC or DMA). Once transfer done we can move
1828 * to the next step which is WAITING_NOTBUSY in write
1829 * case and directly SENDING_STOP in read case.
1830 */
1831 dev_dbg(dev, "FSM: xfer complete?\n");
1832 if (!atmci_test_and_clear_pending(host,
1833 EVENT_XFER_COMPLETE))
1834 break;
1835
1836 dev_dbg(dev, "(%s) set completed xfer complete\n", __func__);
1837 atmci_set_completed(host, EVENT_XFER_COMPLETE);
1838
1839 if (host->caps.need_notbusy_for_read_ops ||
1840 (host->data->flags & MMC_DATA_WRITE)) {
1841 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1842 state = STATE_WAITING_NOTBUSY;
1843 } else if (host->mrq->stop) {
1844 atmci_send_stop_cmd(host, data);
1845 state = STATE_SENDING_STOP;
1846 } else {
1847 host->data = NULL;
1848 data->bytes_xfered = data->blocks * data->blksz;
1849 data->error = 0;
1850 state = STATE_END_REQUEST;
1851 }
1852 break;
1853
1854 case STATE_WAITING_NOTBUSY:
1855 /*
1856 * We can be in the state for two reasons: a command
1857 * requiring waiting not busy signal (stop command
1858 * included) or a write operation. In the latest case,
1859 * we need to send a stop command.
1860 */
1861 dev_dbg(dev, "FSM: not busy?\n");
1862 if (!atmci_test_and_clear_pending(host,
1863 EVENT_NOTBUSY))
1864 break;
1865
1866 dev_dbg(dev, "set completed not busy\n");
1867 atmci_set_completed(host, EVENT_NOTBUSY);
1868
1869 if (host->data) {
1870 /*
1871 * For some commands such as CMD53, even if
1872 * there is data transfer, there is no stop
1873 * command to send.
1874 */
1875 if (host->mrq->stop) {
1876 atmci_send_stop_cmd(host, data);
1877 state = STATE_SENDING_STOP;
1878 } else {
1879 host->data = NULL;
1880 data->bytes_xfered = data->blocks
1881 * data->blksz;
1882 data->error = 0;
1883 state = STATE_END_REQUEST;
1884 }
1885 } else
1886 state = STATE_END_REQUEST;
1887 break;
1888
1889 case STATE_SENDING_STOP:
1890 /*
1891 * In this state, it is important to set host->data to
1892 * NULL (which is tested in the waiting notbusy state)
1893 * in order to go to the end request state instead of
1894 * sending stop again.
1895 */
1896 dev_dbg(dev, "FSM: cmd ready?\n");
1897 if (!atmci_test_and_clear_pending(host,
1898 EVENT_CMD_RDY))
1899 break;
1900
1901 dev_dbg(dev, "FSM: cmd ready\n");
1902 host->cmd = NULL;
1903 data->bytes_xfered = data->blocks * data->blksz;
1904 data->error = 0;
1905 atmci_command_complete(host, mrq->stop);
1906 if (mrq->stop->error) {
1907 host->stop_transfer(host);
1908 atmci_writel(host, ATMCI_IDR,
1909 ATMCI_TXRDY | ATMCI_RXRDY
1910 | ATMCI_DATA_ERROR_FLAGS);
1911 state = STATE_END_REQUEST;
1912 } else {
1913 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1914 state = STATE_WAITING_NOTBUSY;
1915 }
1916 host->data = NULL;
1917 break;
1918
1919 case STATE_END_REQUEST:
1920 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY | ATMCI_RXRDY
1921 | ATMCI_DATA_ERROR_FLAGS);
1922 status = host->data_status;
1923 if (unlikely(status)) {
1924 host->stop_transfer(host);
1925 host->data = NULL;
1926 if (data) {
1927 if (status & ATMCI_DTOE) {
1928 data->error = -ETIMEDOUT;
1929 } else if (status & ATMCI_DCRCE) {
1930 data->error = -EILSEQ;
1931 } else {
1932 data->error = -EIO;
1933 }
1934 }
1935 }
1936
1937 atmci_request_end(host, host->mrq);
1938 goto unlock; /* atmci_request_end() sets host->state */
1939 break;
1940 }
1941 } while (state != prev_state);
1942
1943 host->state = state;
1944
1945unlock:
1946 spin_unlock(&host->lock);
1947}
1948
1949static void atmci_read_data_pio(struct atmel_mci *host)
1950{
1951 struct scatterlist *sg = host->sg;
1952 unsigned int offset = host->pio_offset;
1953 struct mmc_data *data = host->data;
1954 u32 value;
1955 u32 status;
1956 unsigned int nbytes = 0;
1957
1958 do {
1959 value = atmci_readl(host, ATMCI_RDR);
1960 if (likely(offset + 4 <= sg->length)) {
1961 sg_pcopy_from_buffer(sg, 1, &value, sizeof(u32), offset);
1962
1963 offset += 4;
1964 nbytes += 4;
1965
1966 if (offset == sg->length) {
1967 flush_dcache_page(sg_page(sg));
1968 host->sg = sg = sg_next(sg);
1969 host->sg_len--;
1970 if (!sg || !host->sg_len)
1971 goto done;
1972
1973 offset = 0;
1974 }
1975 } else {
1976 unsigned int remaining = sg->length - offset;
1977
1978 sg_pcopy_from_buffer(sg, 1, &value, remaining, offset);
1979 nbytes += remaining;
1980
1981 flush_dcache_page(sg_page(sg));
1982 host->sg = sg = sg_next(sg);
1983 host->sg_len--;
1984 if (!sg || !host->sg_len)
1985 goto done;
1986
1987 offset = 4 - remaining;
1988 sg_pcopy_from_buffer(sg, 1, (u8 *)&value + remaining,
1989 offset, 0);
1990 nbytes += offset;
1991 }
1992
1993 status = atmci_readl(host, ATMCI_SR);
1994 if (status & ATMCI_DATA_ERROR_FLAGS) {
1995 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_RXRDY
1996 | ATMCI_DATA_ERROR_FLAGS));
1997 host->data_status = status;
1998 data->bytes_xfered += nbytes;
1999 return;
2000 }
2001 } while (status & ATMCI_RXRDY);
2002
2003 host->pio_offset = offset;
2004 data->bytes_xfered += nbytes;
2005
2006 return;
2007
2008done:
2009 atmci_writel(host, ATMCI_IDR, ATMCI_RXRDY);
2010 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2011 data->bytes_xfered += nbytes;
2012 smp_wmb();
2013 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2014}
2015
2016static void atmci_write_data_pio(struct atmel_mci *host)
2017{
2018 struct scatterlist *sg = host->sg;
2019 unsigned int offset = host->pio_offset;
2020 struct mmc_data *data = host->data;
2021 u32 value;
2022 u32 status;
2023 unsigned int nbytes = 0;
2024
2025 do {
2026 if (likely(offset + 4 <= sg->length)) {
2027 sg_pcopy_to_buffer(sg, 1, &value, sizeof(u32), offset);
2028 atmci_writel(host, ATMCI_TDR, value);
2029
2030 offset += 4;
2031 nbytes += 4;
2032 if (offset == sg->length) {
2033 host->sg = sg = sg_next(sg);
2034 host->sg_len--;
2035 if (!sg || !host->sg_len)
2036 goto done;
2037
2038 offset = 0;
2039 }
2040 } else {
2041 unsigned int remaining = sg->length - offset;
2042
2043 value = 0;
2044 sg_pcopy_to_buffer(sg, 1, &value, remaining, offset);
2045 nbytes += remaining;
2046
2047 host->sg = sg = sg_next(sg);
2048 host->sg_len--;
2049 if (!sg || !host->sg_len) {
2050 atmci_writel(host, ATMCI_TDR, value);
2051 goto done;
2052 }
2053
2054 offset = 4 - remaining;
2055 sg_pcopy_to_buffer(sg, 1, (u8 *)&value + remaining,
2056 offset, 0);
2057 atmci_writel(host, ATMCI_TDR, value);
2058 nbytes += offset;
2059 }
2060
2061 status = atmci_readl(host, ATMCI_SR);
2062 if (status & ATMCI_DATA_ERROR_FLAGS) {
2063 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_TXRDY
2064 | ATMCI_DATA_ERROR_FLAGS));
2065 host->data_status = status;
2066 data->bytes_xfered += nbytes;
2067 return;
2068 }
2069 } while (status & ATMCI_TXRDY);
2070
2071 host->pio_offset = offset;
2072 data->bytes_xfered += nbytes;
2073
2074 return;
2075
2076done:
2077 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY);
2078 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2079 data->bytes_xfered += nbytes;
2080 smp_wmb();
2081 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2082}
2083
2084static void atmci_sdio_interrupt(struct atmel_mci *host, u32 status)
2085{
2086 int i;
2087
2088 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2089 struct atmel_mci_slot *slot = host->slot[i];
2090 if (slot && (status & slot->sdio_irq)) {
2091 mmc_signal_sdio_irq(slot->mmc);
2092 }
2093 }
2094}
2095
2096
2097static irqreturn_t atmci_interrupt(int irq, void *dev_id)
2098{
2099 struct atmel_mci *host = dev_id;
2100 struct device *dev = host->dev;
2101 u32 status, mask, pending;
2102 unsigned int pass_count = 0;
2103
2104 do {
2105 status = atmci_readl(host, ATMCI_SR);
2106 mask = atmci_readl(host, ATMCI_IMR);
2107 pending = status & mask;
2108 if (!pending)
2109 break;
2110
2111 if (pending & ATMCI_DATA_ERROR_FLAGS) {
2112 dev_dbg(dev, "IRQ: data error\n");
2113 atmci_writel(host, ATMCI_IDR, ATMCI_DATA_ERROR_FLAGS
2114 | ATMCI_RXRDY | ATMCI_TXRDY
2115 | ATMCI_ENDRX | ATMCI_ENDTX
2116 | ATMCI_RXBUFF | ATMCI_TXBUFE);
2117
2118 host->data_status = status;
2119 dev_dbg(dev, "set pending data error\n");
2120 smp_wmb();
2121 atmci_set_pending(host, EVENT_DATA_ERROR);
2122 queue_work(system_bh_wq, &host->bh_work);
2123 }
2124
2125 if (pending & ATMCI_TXBUFE) {
2126 dev_dbg(dev, "IRQ: tx buffer empty\n");
2127 atmci_writel(host, ATMCI_IDR, ATMCI_TXBUFE);
2128 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2129 /*
2130 * We can receive this interruption before having configured
2131 * the second pdc buffer, so we need to reconfigure first and
2132 * second buffers again
2133 */
2134 if (host->data_size) {
2135 atmci_pdc_set_both_buf(host, XFER_TRANSMIT);
2136 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2137 atmci_writel(host, ATMCI_IER, ATMCI_TXBUFE);
2138 } else {
2139 atmci_pdc_complete(host);
2140 }
2141 } else if (pending & ATMCI_ENDTX) {
2142 dev_dbg(dev, "IRQ: end of tx buffer\n");
2143 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2144
2145 if (host->data_size) {
2146 atmci_pdc_set_single_buf(host,
2147 XFER_TRANSMIT, PDC_SECOND_BUF);
2148 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2149 }
2150 }
2151
2152 if (pending & ATMCI_RXBUFF) {
2153 dev_dbg(dev, "IRQ: rx buffer full\n");
2154 atmci_writel(host, ATMCI_IDR, ATMCI_RXBUFF);
2155 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2156 /*
2157 * We can receive this interruption before having configured
2158 * the second pdc buffer, so we need to reconfigure first and
2159 * second buffers again
2160 */
2161 if (host->data_size) {
2162 atmci_pdc_set_both_buf(host, XFER_RECEIVE);
2163 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2164 atmci_writel(host, ATMCI_IER, ATMCI_RXBUFF);
2165 } else {
2166 atmci_pdc_complete(host);
2167 }
2168 } else if (pending & ATMCI_ENDRX) {
2169 dev_dbg(dev, "IRQ: end of rx buffer\n");
2170 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2171
2172 if (host->data_size) {
2173 atmci_pdc_set_single_buf(host,
2174 XFER_RECEIVE, PDC_SECOND_BUF);
2175 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2176 }
2177 }
2178
2179 /*
2180 * First mci IPs, so mainly the ones having pdc, have some
2181 * issues with the notbusy signal. You can't get it after
2182 * data transmission if you have not sent a stop command.
2183 * The appropriate workaround is to use the BLKE signal.
2184 */
2185 if (pending & ATMCI_BLKE) {
2186 dev_dbg(dev, "IRQ: blke\n");
2187 atmci_writel(host, ATMCI_IDR, ATMCI_BLKE);
2188 smp_wmb();
2189 dev_dbg(dev, "set pending notbusy\n");
2190 atmci_set_pending(host, EVENT_NOTBUSY);
2191 queue_work(system_bh_wq, &host->bh_work);
2192 }
2193
2194 if (pending & ATMCI_NOTBUSY) {
2195 dev_dbg(dev, "IRQ: not_busy\n");
2196 atmci_writel(host, ATMCI_IDR, ATMCI_NOTBUSY);
2197 smp_wmb();
2198 dev_dbg(dev, "set pending notbusy\n");
2199 atmci_set_pending(host, EVENT_NOTBUSY);
2200 queue_work(system_bh_wq, &host->bh_work);
2201 }
2202
2203 if (pending & ATMCI_RXRDY)
2204 atmci_read_data_pio(host);
2205 if (pending & ATMCI_TXRDY)
2206 atmci_write_data_pio(host);
2207
2208 if (pending & ATMCI_CMDRDY) {
2209 dev_dbg(dev, "IRQ: cmd ready\n");
2210 atmci_writel(host, ATMCI_IDR, ATMCI_CMDRDY);
2211 host->cmd_status = status;
2212 smp_wmb();
2213 dev_dbg(dev, "set pending cmd rdy\n");
2214 atmci_set_pending(host, EVENT_CMD_RDY);
2215 queue_work(system_bh_wq, &host->bh_work);
2216 }
2217
2218 if (pending & (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
2219 atmci_sdio_interrupt(host, status);
2220
2221 } while (pass_count++ < 5);
2222
2223 return pass_count ? IRQ_HANDLED : IRQ_NONE;
2224}
2225
2226static irqreturn_t atmci_detect_interrupt(int irq, void *dev_id)
2227{
2228 struct atmel_mci_slot *slot = dev_id;
2229
2230 /*
2231 * Disable interrupts until the pin has stabilized and check
2232 * the state then. Use mod_timer() since we may be in the
2233 * middle of the timer routine when this interrupt triggers.
2234 */
2235 disable_irq_nosync(irq);
2236 mod_timer(&slot->detect_timer, jiffies + msecs_to_jiffies(20));
2237
2238 return IRQ_HANDLED;
2239}
2240
2241static int atmci_init_slot(struct atmel_mci *host,
2242 struct mci_slot_pdata *slot_data, unsigned int id,
2243 u32 sdc_reg, u32 sdio_irq)
2244{
2245 struct device *dev = host->dev;
2246 struct mmc_host *mmc;
2247 struct atmel_mci_slot *slot;
2248 int ret;
2249
2250 mmc = mmc_alloc_host(sizeof(struct atmel_mci_slot), dev);
2251 if (!mmc)
2252 return -ENOMEM;
2253
2254 slot = mmc_priv(mmc);
2255 slot->mmc = mmc;
2256 slot->host = host;
2257 slot->detect_pin = slot_data->detect_pin;
2258 slot->wp_pin = slot_data->wp_pin;
2259 slot->sdc_reg = sdc_reg;
2260 slot->sdio_irq = sdio_irq;
2261
2262 dev_dbg(&mmc->class_dev,
2263 "slot[%u]: bus_width=%u, detect_pin=%d, "
2264 "detect_is_active_high=%s, wp_pin=%d\n",
2265 id, slot_data->bus_width, desc_to_gpio(slot_data->detect_pin),
2266 !gpiod_is_active_low(slot_data->detect_pin) ? "true" : "false",
2267 desc_to_gpio(slot_data->wp_pin));
2268
2269 mmc->ops = &atmci_ops;
2270 mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
2271 mmc->f_max = host->bus_hz / 2;
2272 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2273 if (sdio_irq)
2274 mmc->caps |= MMC_CAP_SDIO_IRQ;
2275 if (host->caps.has_highspeed)
2276 mmc->caps |= MMC_CAP_SD_HIGHSPEED;
2277 /*
2278 * Without the read/write proof capability, it is strongly suggested to
2279 * use only one bit for data to prevent fifo underruns and overruns
2280 * which will corrupt data.
2281 */
2282 if ((slot_data->bus_width >= 4) && host->caps.has_rwproof) {
2283 mmc->caps |= MMC_CAP_4_BIT_DATA;
2284 if (slot_data->bus_width >= 8)
2285 mmc->caps |= MMC_CAP_8_BIT_DATA;
2286 }
2287
2288 if (atmci_get_version(host) < 0x200) {
2289 mmc->max_segs = 256;
2290 mmc->max_blk_size = 4095;
2291 mmc->max_blk_count = 256;
2292 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2293 mmc->max_seg_size = mmc->max_blk_size * mmc->max_segs;
2294 } else {
2295 mmc->max_segs = 64;
2296 mmc->max_req_size = 32768 * 512;
2297 mmc->max_blk_size = 32768;
2298 mmc->max_blk_count = 512;
2299 }
2300
2301 /* Assume card is present initially */
2302 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
2303 if (slot->detect_pin) {
2304 if (!gpiod_get_value_cansleep(slot->detect_pin))
2305 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
2306 } else {
2307 dev_dbg(&mmc->class_dev, "no detect pin available\n");
2308 }
2309
2310 if (!slot->detect_pin) {
2311 if (slot_data->non_removable)
2312 mmc->caps |= MMC_CAP_NONREMOVABLE;
2313 else
2314 mmc->caps |= MMC_CAP_NEEDS_POLL;
2315 }
2316
2317 if (!slot->wp_pin)
2318 dev_dbg(&mmc->class_dev, "no WP pin available\n");
2319
2320 host->slot[id] = slot;
2321 mmc_regulator_get_supply(mmc);
2322 ret = mmc_add_host(mmc);
2323 if (ret) {
2324 mmc_free_host(mmc);
2325 return ret;
2326 }
2327
2328 if (slot->detect_pin) {
2329 timer_setup(&slot->detect_timer, atmci_detect_change, 0);
2330
2331 ret = request_irq(gpiod_to_irq(slot->detect_pin),
2332 atmci_detect_interrupt,
2333 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
2334 "mmc-detect", slot);
2335 if (ret) {
2336 dev_dbg(&mmc->class_dev,
2337 "could not request IRQ %d for detect pin\n",
2338 gpiod_to_irq(slot->detect_pin));
2339 slot->detect_pin = NULL;
2340 }
2341 }
2342
2343 atmci_init_debugfs(slot);
2344
2345 return 0;
2346}
2347
2348static void atmci_cleanup_slot(struct atmel_mci_slot *slot,
2349 unsigned int id)
2350{
2351 /* Debugfs stuff is cleaned up by mmc core */
2352
2353 set_bit(ATMCI_SHUTDOWN, &slot->flags);
2354 smp_wmb();
2355
2356 mmc_remove_host(slot->mmc);
2357
2358 if (slot->detect_pin) {
2359 free_irq(gpiod_to_irq(slot->detect_pin), slot);
2360 del_timer_sync(&slot->detect_timer);
2361 }
2362
2363 slot->host->slot[id] = NULL;
2364 mmc_free_host(slot->mmc);
2365}
2366
2367static int atmci_configure_dma(struct atmel_mci *host)
2368{
2369 struct device *dev = host->dev;
2370
2371 host->dma.chan = dma_request_chan(dev, "rxtx");
2372 if (IS_ERR(host->dma.chan))
2373 return PTR_ERR(host->dma.chan);
2374
2375 dev_info(dev, "using %s for DMA transfers\n", dma_chan_name(host->dma.chan));
2376
2377 host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
2378 host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2379 host->dma_conf.src_maxburst = 1;
2380 host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
2381 host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2382 host->dma_conf.dst_maxburst = 1;
2383 host->dma_conf.device_fc = false;
2384
2385 return 0;
2386}
2387
2388/*
2389 * HSMCI (High Speed MCI) module is not fully compatible with MCI module.
2390 * HSMCI provides DMA support and a new config register but no more supports
2391 * PDC.
2392 */
2393static void atmci_get_cap(struct atmel_mci *host)
2394{
2395 struct device *dev = host->dev;
2396 unsigned int version;
2397
2398 version = atmci_get_version(host);
2399 dev_info(dev, "version: 0x%x\n", version);
2400
2401 host->caps.has_dma_conf_reg = false;
2402 host->caps.has_pdc = true;
2403 host->caps.has_cfg_reg = false;
2404 host->caps.has_cstor_reg = false;
2405 host->caps.has_highspeed = false;
2406 host->caps.has_rwproof = false;
2407 host->caps.has_odd_clk_div = false;
2408 host->caps.has_bad_data_ordering = true;
2409 host->caps.need_reset_after_xfer = true;
2410 host->caps.need_blksz_mul_4 = true;
2411 host->caps.need_notbusy_for_read_ops = false;
2412
2413 /* keep only major version number */
2414 switch (version & 0xf00) {
2415 case 0x600:
2416 case 0x500:
2417 host->caps.has_odd_clk_div = true;
2418 fallthrough;
2419 case 0x400:
2420 case 0x300:
2421 host->caps.has_dma_conf_reg = true;
2422 host->caps.has_pdc = false;
2423 host->caps.has_cfg_reg = true;
2424 host->caps.has_cstor_reg = true;
2425 host->caps.has_highspeed = true;
2426 fallthrough;
2427 case 0x200:
2428 host->caps.has_rwproof = true;
2429 host->caps.need_blksz_mul_4 = false;
2430 host->caps.need_notbusy_for_read_ops = true;
2431 fallthrough;
2432 case 0x100:
2433 host->caps.has_bad_data_ordering = false;
2434 host->caps.need_reset_after_xfer = false;
2435 fallthrough;
2436 case 0x0:
2437 break;
2438 default:
2439 host->caps.has_pdc = false;
2440 dev_warn(dev, "Unmanaged mci version, set minimum capabilities\n");
2441 break;
2442 }
2443}
2444
2445static int atmci_probe(struct platform_device *pdev)
2446{
2447 struct device *dev = &pdev->dev;
2448 struct atmel_mci *host;
2449 struct resource *regs;
2450 unsigned int nr_slots;
2451 int irq;
2452 int ret, i;
2453
2454 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2455 if (!regs)
2456 return -ENXIO;
2457
2458 irq = platform_get_irq(pdev, 0);
2459 if (irq < 0)
2460 return irq;
2461
2462 host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
2463 if (!host)
2464 return -ENOMEM;
2465
2466 host->dev = dev;
2467 spin_lock_init(&host->lock);
2468 INIT_LIST_HEAD(&host->queue);
2469
2470 ret = atmci_of_init(host);
2471 if (ret)
2472 return dev_err_probe(dev, ret, "Slot information not available\n");
2473
2474 host->mck = devm_clk_get(dev, "mci_clk");
2475 if (IS_ERR(host->mck))
2476 return PTR_ERR(host->mck);
2477
2478 host->regs = devm_ioremap(dev, regs->start, resource_size(regs));
2479 if (!host->regs)
2480 return -ENOMEM;
2481
2482 ret = clk_prepare_enable(host->mck);
2483 if (ret)
2484 return ret;
2485
2486 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
2487 host->bus_hz = clk_get_rate(host->mck);
2488
2489 host->mapbase = regs->start;
2490
2491 INIT_WORK(&host->bh_work, atmci_work_func);
2492
2493 ret = request_irq(irq, atmci_interrupt, 0, dev_name(dev), host);
2494 if (ret) {
2495 clk_disable_unprepare(host->mck);
2496 return ret;
2497 }
2498
2499 /* Get MCI capabilities and set operations according to it */
2500 atmci_get_cap(host);
2501 ret = atmci_configure_dma(host);
2502 if (ret == -EPROBE_DEFER)
2503 goto err_dma_probe_defer;
2504 if (ret == 0) {
2505 host->prepare_data = &atmci_prepare_data_dma;
2506 host->submit_data = &atmci_submit_data_dma;
2507 host->stop_transfer = &atmci_stop_transfer_dma;
2508 } else if (host->caps.has_pdc) {
2509 dev_info(dev, "using PDC\n");
2510 host->prepare_data = &atmci_prepare_data_pdc;
2511 host->submit_data = &atmci_submit_data_pdc;
2512 host->stop_transfer = &atmci_stop_transfer_pdc;
2513 } else {
2514 dev_info(dev, "using PIO\n");
2515 host->prepare_data = &atmci_prepare_data;
2516 host->submit_data = &atmci_submit_data;
2517 host->stop_transfer = &atmci_stop_transfer;
2518 }
2519
2520 platform_set_drvdata(pdev, host);
2521
2522 timer_setup(&host->timer, atmci_timeout_timer, 0);
2523
2524 pm_runtime_get_noresume(dev);
2525 pm_runtime_set_active(dev);
2526 pm_runtime_set_autosuspend_delay(dev, AUTOSUSPEND_DELAY);
2527 pm_runtime_use_autosuspend(dev);
2528 pm_runtime_enable(dev);
2529
2530 /* We need at least one slot to succeed */
2531 nr_slots = 0;
2532 ret = -ENODEV;
2533 if (host->pdata[0].bus_width) {
2534 ret = atmci_init_slot(host, &host->pdata[0],
2535 0, ATMCI_SDCSEL_SLOT_A, ATMCI_SDIOIRQA);
2536 if (!ret) {
2537 nr_slots++;
2538 host->buf_size = host->slot[0]->mmc->max_req_size;
2539 }
2540 }
2541 if (host->pdata[1].bus_width) {
2542 ret = atmci_init_slot(host, &host->pdata[1],
2543 1, ATMCI_SDCSEL_SLOT_B, ATMCI_SDIOIRQB);
2544 if (!ret) {
2545 nr_slots++;
2546 if (host->slot[1]->mmc->max_req_size > host->buf_size)
2547 host->buf_size =
2548 host->slot[1]->mmc->max_req_size;
2549 }
2550 }
2551
2552 if (!nr_slots) {
2553 dev_err_probe(dev, ret, "init failed: no slot defined\n");
2554 goto err_init_slot;
2555 }
2556
2557 if (!host->caps.has_rwproof) {
2558 host->buffer = dma_alloc_coherent(dev, host->buf_size,
2559 &host->buf_phys_addr,
2560 GFP_KERNEL);
2561 if (!host->buffer) {
2562 ret = dev_err_probe(dev, -ENOMEM, "buffer allocation failed\n");
2563 goto err_dma_alloc;
2564 }
2565 }
2566
2567 dev_info(dev, "Atmel MCI controller at 0x%08lx irq %d, %u slots\n",
2568 host->mapbase, irq, nr_slots);
2569
2570 pm_runtime_mark_last_busy(dev);
2571 pm_runtime_put_autosuspend(dev);
2572
2573 return 0;
2574
2575err_dma_alloc:
2576 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2577 if (host->slot[i])
2578 atmci_cleanup_slot(host->slot[i], i);
2579 }
2580err_init_slot:
2581 clk_disable_unprepare(host->mck);
2582
2583 pm_runtime_disable(dev);
2584 pm_runtime_put_noidle(dev);
2585
2586 del_timer_sync(&host->timer);
2587 if (!IS_ERR(host->dma.chan))
2588 dma_release_channel(host->dma.chan);
2589err_dma_probe_defer:
2590 free_irq(irq, host);
2591 return ret;
2592}
2593
2594static void atmci_remove(struct platform_device *pdev)
2595{
2596 struct atmel_mci *host = platform_get_drvdata(pdev);
2597 struct device *dev = &pdev->dev;
2598 unsigned int i;
2599
2600 pm_runtime_get_sync(dev);
2601
2602 if (host->buffer)
2603 dma_free_coherent(dev, host->buf_size, host->buffer, host->buf_phys_addr);
2604
2605 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2606 if (host->slot[i])
2607 atmci_cleanup_slot(host->slot[i], i);
2608 }
2609
2610 atmci_writel(host, ATMCI_IDR, ~0UL);
2611 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
2612 atmci_readl(host, ATMCI_SR);
2613
2614 del_timer_sync(&host->timer);
2615 if (!IS_ERR(host->dma.chan))
2616 dma_release_channel(host->dma.chan);
2617
2618 free_irq(platform_get_irq(pdev, 0), host);
2619
2620 clk_disable_unprepare(host->mck);
2621
2622 pm_runtime_disable(dev);
2623 pm_runtime_put_noidle(dev);
2624}
2625
2626#ifdef CONFIG_PM
2627static int atmci_runtime_suspend(struct device *dev)
2628{
2629 struct atmel_mci *host = dev_get_drvdata(dev);
2630
2631 clk_disable_unprepare(host->mck);
2632
2633 pinctrl_pm_select_sleep_state(dev);
2634
2635 return 0;
2636}
2637
2638static int atmci_runtime_resume(struct device *dev)
2639{
2640 struct atmel_mci *host = dev_get_drvdata(dev);
2641
2642 pinctrl_select_default_state(dev);
2643
2644 return clk_prepare_enable(host->mck);
2645}
2646#endif
2647
2648static const struct dev_pm_ops atmci_dev_pm_ops = {
2649 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
2650 pm_runtime_force_resume)
2651 SET_RUNTIME_PM_OPS(atmci_runtime_suspend, atmci_runtime_resume, NULL)
2652};
2653
2654static struct platform_driver atmci_driver = {
2655 .probe = atmci_probe,
2656 .remove = atmci_remove,
2657 .driver = {
2658 .name = "atmel_mci",
2659 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
2660 .of_match_table = atmci_dt_ids,
2661 .pm = &atmci_dev_pm_ops,
2662 },
2663};
2664module_platform_driver(atmci_driver);
2665
2666MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver");
2667MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
2668MODULE_LICENSE("GPL v2");