Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Atmel MultiMedia Card Interface driver
4 *
5 * Copyright (C) 2004-2008 Atmel Corporation
6 */
7#include <linux/blkdev.h>
8#include <linux/clk.h>
9#include <linux/debugfs.h>
10#include <linux/device.h>
11#include <linux/dmaengine.h>
12#include <linux/dma-mapping.h>
13#include <linux/err.h>
14#include <linux/gpio.h>
15#include <linux/init.h>
16#include <linux/interrupt.h>
17#include <linux/io.h>
18#include <linux/ioport.h>
19#include <linux/module.h>
20#include <linux/of.h>
21#include <linux/of_device.h>
22#include <linux/of_gpio.h>
23#include <linux/platform_device.h>
24#include <linux/scatterlist.h>
25#include <linux/seq_file.h>
26#include <linux/slab.h>
27#include <linux/stat.h>
28#include <linux/types.h>
29
30#include <linux/mmc/host.h>
31#include <linux/mmc/sdio.h>
32
33#include <linux/atmel-mci.h>
34#include <linux/atmel_pdc.h>
35#include <linux/pm.h>
36#include <linux/pm_runtime.h>
37#include <linux/pinctrl/consumer.h>
38
39#include <asm/cacheflush.h>
40#include <asm/io.h>
41#include <asm/unaligned.h>
42
43/*
44 * Superset of MCI IP registers integrated in Atmel AT91 Processor
45 * Registers and bitfields marked with [2] are only available in MCI2
46 */
47
48/* MCI Register Definitions */
49#define ATMCI_CR 0x0000 /* Control */
50#define ATMCI_CR_MCIEN BIT(0) /* MCI Enable */
51#define ATMCI_CR_MCIDIS BIT(1) /* MCI Disable */
52#define ATMCI_CR_PWSEN BIT(2) /* Power Save Enable */
53#define ATMCI_CR_PWSDIS BIT(3) /* Power Save Disable */
54#define ATMCI_CR_SWRST BIT(7) /* Software Reset */
55#define ATMCI_MR 0x0004 /* Mode */
56#define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
57#define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
58#define ATMCI_MR_RDPROOF BIT(11) /* Read Proof */
59#define ATMCI_MR_WRPROOF BIT(12) /* Write Proof */
60#define ATMCI_MR_PDCFBYTE BIT(13) /* Force Byte Transfer */
61#define ATMCI_MR_PDCPADV BIT(14) /* Padding Value */
62#define ATMCI_MR_PDCMODE BIT(15) /* PDC-oriented Mode */
63#define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
64#define ATMCI_DTOR 0x0008 /* Data Timeout */
65#define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
66#define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
67#define ATMCI_SDCR 0x000c /* SD Card / SDIO */
68#define ATMCI_SDCSEL_SLOT_A (0 << 0) /* Select SD slot A */
69#define ATMCI_SDCSEL_SLOT_B (1 << 0) /* Select SD slot A */
70#define ATMCI_SDCSEL_MASK (3 << 0)
71#define ATMCI_SDCBUS_1BIT (0 << 6) /* 1-bit data bus */
72#define ATMCI_SDCBUS_4BIT (2 << 6) /* 4-bit data bus */
73#define ATMCI_SDCBUS_8BIT (3 << 6) /* 8-bit data bus[2] */
74#define ATMCI_SDCBUS_MASK (3 << 6)
75#define ATMCI_ARGR 0x0010 /* Command Argument */
76#define ATMCI_CMDR 0x0014 /* Command */
77#define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
78#define ATMCI_CMDR_RSPTYP_NONE (0 << 6) /* No response */
79#define ATMCI_CMDR_RSPTYP_48BIT (1 << 6) /* 48-bit response */
80#define ATMCI_CMDR_RSPTYP_136BIT (2 << 6) /* 136-bit response */
81#define ATMCI_CMDR_SPCMD_INIT (1 << 8) /* Initialization command */
82#define ATMCI_CMDR_SPCMD_SYNC (2 << 8) /* Synchronized command */
83#define ATMCI_CMDR_SPCMD_INT (4 << 8) /* Interrupt command */
84#define ATMCI_CMDR_SPCMD_INTRESP (5 << 8) /* Interrupt response */
85#define ATMCI_CMDR_OPDCMD (1 << 11) /* Open Drain */
86#define ATMCI_CMDR_MAXLAT_5CYC (0 << 12) /* Max latency 5 cycles */
87#define ATMCI_CMDR_MAXLAT_64CYC (1 << 12) /* Max latency 64 cycles */
88#define ATMCI_CMDR_START_XFER (1 << 16) /* Start data transfer */
89#define ATMCI_CMDR_STOP_XFER (2 << 16) /* Stop data transfer */
90#define ATMCI_CMDR_TRDIR_WRITE (0 << 18) /* Write data */
91#define ATMCI_CMDR_TRDIR_READ (1 << 18) /* Read data */
92#define ATMCI_CMDR_BLOCK (0 << 19) /* Single-block transfer */
93#define ATMCI_CMDR_MULTI_BLOCK (1 << 19) /* Multi-block transfer */
94#define ATMCI_CMDR_STREAM (2 << 19) /* MMC Stream transfer */
95#define ATMCI_CMDR_SDIO_BYTE (4 << 19) /* SDIO Byte transfer */
96#define ATMCI_CMDR_SDIO_BLOCK (5 << 19) /* SDIO Block transfer */
97#define ATMCI_CMDR_SDIO_SUSPEND (1 << 24) /* SDIO Suspend Command */
98#define ATMCI_CMDR_SDIO_RESUME (2 << 24) /* SDIO Resume Command */
99#define ATMCI_BLKR 0x0018 /* Block */
100#define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
101#define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
102#define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
103#define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
104#define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
105#define ATMCI_RSPR 0x0020 /* Response 0 */
106#define ATMCI_RSPR1 0x0024 /* Response 1 */
107#define ATMCI_RSPR2 0x0028 /* Response 2 */
108#define ATMCI_RSPR3 0x002c /* Response 3 */
109#define ATMCI_RDR 0x0030 /* Receive Data */
110#define ATMCI_TDR 0x0034 /* Transmit Data */
111#define ATMCI_SR 0x0040 /* Status */
112#define ATMCI_IER 0x0044 /* Interrupt Enable */
113#define ATMCI_IDR 0x0048 /* Interrupt Disable */
114#define ATMCI_IMR 0x004c /* Interrupt Mask */
115#define ATMCI_CMDRDY BIT(0) /* Command Ready */
116#define ATMCI_RXRDY BIT(1) /* Receiver Ready */
117#define ATMCI_TXRDY BIT(2) /* Transmitter Ready */
118#define ATMCI_BLKE BIT(3) /* Data Block Ended */
119#define ATMCI_DTIP BIT(4) /* Data Transfer In Progress */
120#define ATMCI_NOTBUSY BIT(5) /* Data Not Busy */
121#define ATMCI_ENDRX BIT(6) /* End of RX Buffer */
122#define ATMCI_ENDTX BIT(7) /* End of TX Buffer */
123#define ATMCI_SDIOIRQA BIT(8) /* SDIO IRQ in slot A */
124#define ATMCI_SDIOIRQB BIT(9) /* SDIO IRQ in slot B */
125#define ATMCI_SDIOWAIT BIT(12) /* SDIO Read Wait Operation Status */
126#define ATMCI_CSRCV BIT(13) /* CE-ATA Completion Signal Received */
127#define ATMCI_RXBUFF BIT(14) /* RX Buffer Full */
128#define ATMCI_TXBUFE BIT(15) /* TX Buffer Empty */
129#define ATMCI_RINDE BIT(16) /* Response Index Error */
130#define ATMCI_RDIRE BIT(17) /* Response Direction Error */
131#define ATMCI_RCRCE BIT(18) /* Response CRC Error */
132#define ATMCI_RENDE BIT(19) /* Response End Bit Error */
133#define ATMCI_RTOE BIT(20) /* Response Time-Out Error */
134#define ATMCI_DCRCE BIT(21) /* Data CRC Error */
135#define ATMCI_DTOE BIT(22) /* Data Time-Out Error */
136#define ATMCI_CSTOE BIT(23) /* Completion Signal Time-out Error */
137#define ATMCI_BLKOVRE BIT(24) /* DMA Block Overrun Error */
138#define ATMCI_DMADONE BIT(25) /* DMA Transfer Done */
139#define ATMCI_FIFOEMPTY BIT(26) /* FIFO Empty Flag */
140#define ATMCI_XFRDONE BIT(27) /* Transfer Done Flag */
141#define ATMCI_ACKRCV BIT(28) /* Boot Operation Acknowledge Received */
142#define ATMCI_ACKRCVE BIT(29) /* Boot Operation Acknowledge Error */
143#define ATMCI_OVRE BIT(30) /* RX Overrun Error */
144#define ATMCI_UNRE BIT(31) /* TX Underrun Error */
145#define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
146#define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
147#define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
148#define ATMCI_DMAEN BIT(8) /* DMA Hardware Handshaking Enable */
149#define ATMCI_CFG 0x0054 /* Configuration[2] */
150#define ATMCI_CFG_FIFOMODE_1DATA BIT(0) /* MCI Internal FIFO control mode */
151#define ATMCI_CFG_FERRCTRL_COR BIT(4) /* Flow Error flag reset control mode */
152#define ATMCI_CFG_HSMODE BIT(8) /* High Speed Mode */
153#define ATMCI_CFG_LSYNC BIT(12) /* Synchronize on the last block */
154#define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
155#define ATMCI_WP_EN BIT(0) /* WP Enable */
156#define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
157#define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
158#define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
159#define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
160#define ATMCI_VERSION 0x00FC /* Version */
161#define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
162
163/* This is not including the FIFO Aperture on MCI2 */
164#define ATMCI_REGS_SIZE 0x100
165
166/* Register access macros */
167#define atmci_readl(port, reg) \
168 __raw_readl((port)->regs + reg)
169#define atmci_writel(port, reg, value) \
170 __raw_writel((value), (port)->regs + reg)
171
172#define ATMCI_CMD_TIMEOUT_MS 2000
173#define AUTOSUSPEND_DELAY 50
174
175#define ATMCI_DATA_ERROR_FLAGS (ATMCI_DCRCE | ATMCI_DTOE | ATMCI_OVRE | ATMCI_UNRE)
176#define ATMCI_DMA_THRESHOLD 16
177
178enum {
179 EVENT_CMD_RDY = 0,
180 EVENT_XFER_COMPLETE,
181 EVENT_NOTBUSY,
182 EVENT_DATA_ERROR,
183};
184
185enum atmel_mci_state {
186 STATE_IDLE = 0,
187 STATE_SENDING_CMD,
188 STATE_DATA_XFER,
189 STATE_WAITING_NOTBUSY,
190 STATE_SENDING_STOP,
191 STATE_END_REQUEST,
192};
193
194enum atmci_xfer_dir {
195 XFER_RECEIVE = 0,
196 XFER_TRANSMIT,
197};
198
199enum atmci_pdc_buf {
200 PDC_FIRST_BUF = 0,
201 PDC_SECOND_BUF,
202};
203
204struct atmel_mci_caps {
205 bool has_dma_conf_reg;
206 bool has_pdc;
207 bool has_cfg_reg;
208 bool has_cstor_reg;
209 bool has_highspeed;
210 bool has_rwproof;
211 bool has_odd_clk_div;
212 bool has_bad_data_ordering;
213 bool need_reset_after_xfer;
214 bool need_blksz_mul_4;
215 bool need_notbusy_for_read_ops;
216};
217
218struct atmel_mci_dma {
219 struct dma_chan *chan;
220 struct dma_async_tx_descriptor *data_desc;
221};
222
223/**
224 * struct atmel_mci - MMC controller state shared between all slots
225 * @lock: Spinlock protecting the queue and associated data.
226 * @regs: Pointer to MMIO registers.
227 * @sg: Scatterlist entry currently being processed by PIO or PDC code.
228 * @sg_len: Size of the scatterlist
229 * @pio_offset: Offset into the current scatterlist entry.
230 * @buffer: Buffer used if we don't have the r/w proof capability. We
231 * don't have the time to switch pdc buffers so we have to use only
232 * one buffer for the full transaction.
233 * @buf_size: size of the buffer.
234 * @buf_phys_addr: buffer address needed for pdc.
235 * @cur_slot: The slot which is currently using the controller.
236 * @mrq: The request currently being processed on @cur_slot,
237 * or NULL if the controller is idle.
238 * @cmd: The command currently being sent to the card, or NULL.
239 * @data: The data currently being transferred, or NULL if no data
240 * transfer is in progress.
241 * @data_size: just data->blocks * data->blksz.
242 * @dma: DMA client state.
243 * @data_chan: DMA channel being used for the current data transfer.
244 * @dma_conf: Configuration for the DMA slave
245 * @cmd_status: Snapshot of SR taken upon completion of the current
246 * command. Only valid when EVENT_CMD_COMPLETE is pending.
247 * @data_status: Snapshot of SR taken upon completion of the current
248 * data transfer. Only valid when EVENT_DATA_COMPLETE or
249 * EVENT_DATA_ERROR is pending.
250 * @stop_cmdr: Value to be loaded into CMDR when the stop command is
251 * to be sent.
252 * @tasklet: Tasklet running the request state machine.
253 * @pending_events: Bitmask of events flagged by the interrupt handler
254 * to be processed by the tasklet.
255 * @completed_events: Bitmask of events which the state machine has
256 * processed.
257 * @state: Tasklet state.
258 * @queue: List of slots waiting for access to the controller.
259 * @need_clock_update: Update the clock rate before the next request.
260 * @need_reset: Reset controller before next request.
261 * @timer: Timer to balance the data timeout error flag which cannot rise.
262 * @mode_reg: Value of the MR register.
263 * @cfg_reg: Value of the CFG register.
264 * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
265 * rate and timeout calculations.
266 * @mapbase: Physical address of the MMIO registers.
267 * @mck: The peripheral bus clock hooked up to the MMC controller.
268 * @pdev: Platform device associated with the MMC controller.
269 * @slot: Slots sharing this MMC controller.
270 * @caps: MCI capabilities depending on MCI version.
271 * @prepare_data: function to setup MCI before data transfer which
272 * depends on MCI capabilities.
273 * @submit_data: function to start data transfer which depends on MCI
274 * capabilities.
275 * @stop_transfer: function to stop data transfer which depends on MCI
276 * capabilities.
277 *
278 * Locking
279 * =======
280 *
281 * @lock is a softirq-safe spinlock protecting @queue as well as
282 * @cur_slot, @mrq and @state. These must always be updated
283 * at the same time while holding @lock.
284 *
285 * @lock also protects mode_reg and need_clock_update since these are
286 * used to synchronize mode register updates with the queue
287 * processing.
288 *
289 * The @mrq field of struct atmel_mci_slot is also protected by @lock,
290 * and must always be written at the same time as the slot is added to
291 * @queue.
292 *
293 * @pending_events and @completed_events are accessed using atomic bit
294 * operations, so they don't need any locking.
295 *
296 * None of the fields touched by the interrupt handler need any
297 * locking. However, ordering is important: Before EVENT_DATA_ERROR or
298 * EVENT_DATA_COMPLETE is set in @pending_events, all data-related
299 * interrupts must be disabled and @data_status updated with a
300 * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the
301 * CMDRDY interrupt must be disabled and @cmd_status updated with a
302 * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the
303 * bytes_xfered field of @data must be written. This is ensured by
304 * using barriers.
305 */
306struct atmel_mci {
307 spinlock_t lock;
308 void __iomem *regs;
309
310 struct scatterlist *sg;
311 unsigned int sg_len;
312 unsigned int pio_offset;
313 unsigned int *buffer;
314 unsigned int buf_size;
315 dma_addr_t buf_phys_addr;
316
317 struct atmel_mci_slot *cur_slot;
318 struct mmc_request *mrq;
319 struct mmc_command *cmd;
320 struct mmc_data *data;
321 unsigned int data_size;
322
323 struct atmel_mci_dma dma;
324 struct dma_chan *data_chan;
325 struct dma_slave_config dma_conf;
326
327 u32 cmd_status;
328 u32 data_status;
329 u32 stop_cmdr;
330
331 struct tasklet_struct tasklet;
332 unsigned long pending_events;
333 unsigned long completed_events;
334 enum atmel_mci_state state;
335 struct list_head queue;
336
337 bool need_clock_update;
338 bool need_reset;
339 struct timer_list timer;
340 u32 mode_reg;
341 u32 cfg_reg;
342 unsigned long bus_hz;
343 unsigned long mapbase;
344 struct clk *mck;
345 struct platform_device *pdev;
346
347 struct atmel_mci_slot *slot[ATMCI_MAX_NR_SLOTS];
348
349 struct atmel_mci_caps caps;
350
351 u32 (*prepare_data)(struct atmel_mci *host, struct mmc_data *data);
352 void (*submit_data)(struct atmel_mci *host, struct mmc_data *data);
353 void (*stop_transfer)(struct atmel_mci *host);
354};
355
356/**
357 * struct atmel_mci_slot - MMC slot state
358 * @mmc: The mmc_host representing this slot.
359 * @host: The MMC controller this slot is using.
360 * @sdc_reg: Value of SDCR to be written before using this slot.
361 * @sdio_irq: SDIO irq mask for this slot.
362 * @mrq: mmc_request currently being processed or waiting to be
363 * processed, or NULL when the slot is idle.
364 * @queue_node: List node for placing this node in the @queue list of
365 * &struct atmel_mci.
366 * @clock: Clock rate configured by set_ios(). Protected by host->lock.
367 * @flags: Random state bits associated with the slot.
368 * @detect_pin: GPIO pin used for card detection, or negative if not
369 * available.
370 * @wp_pin: GPIO pin used for card write protect sending, or negative
371 * if not available.
372 * @detect_is_active_high: The state of the detect pin when it is active.
373 * @detect_timer: Timer used for debouncing @detect_pin interrupts.
374 */
375struct atmel_mci_slot {
376 struct mmc_host *mmc;
377 struct atmel_mci *host;
378
379 u32 sdc_reg;
380 u32 sdio_irq;
381
382 struct mmc_request *mrq;
383 struct list_head queue_node;
384
385 unsigned int clock;
386 unsigned long flags;
387#define ATMCI_CARD_PRESENT 0
388#define ATMCI_CARD_NEED_INIT 1
389#define ATMCI_SHUTDOWN 2
390
391 int detect_pin;
392 int wp_pin;
393 bool detect_is_active_high;
394
395 struct timer_list detect_timer;
396};
397
398#define atmci_test_and_clear_pending(host, event) \
399 test_and_clear_bit(event, &host->pending_events)
400#define atmci_set_completed(host, event) \
401 set_bit(event, &host->completed_events)
402#define atmci_set_pending(host, event) \
403 set_bit(event, &host->pending_events)
404
405/*
406 * The debugfs stuff below is mostly optimized away when
407 * CONFIG_DEBUG_FS is not set.
408 */
409static int atmci_req_show(struct seq_file *s, void *v)
410{
411 struct atmel_mci_slot *slot = s->private;
412 struct mmc_request *mrq;
413 struct mmc_command *cmd;
414 struct mmc_command *stop;
415 struct mmc_data *data;
416
417 /* Make sure we get a consistent snapshot */
418 spin_lock_bh(&slot->host->lock);
419 mrq = slot->mrq;
420
421 if (mrq) {
422 cmd = mrq->cmd;
423 data = mrq->data;
424 stop = mrq->stop;
425
426 if (cmd)
427 seq_printf(s,
428 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
429 cmd->opcode, cmd->arg, cmd->flags,
430 cmd->resp[0], cmd->resp[1], cmd->resp[2],
431 cmd->resp[3], cmd->error);
432 if (data)
433 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
434 data->bytes_xfered, data->blocks,
435 data->blksz, data->flags, data->error);
436 if (stop)
437 seq_printf(s,
438 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
439 stop->opcode, stop->arg, stop->flags,
440 stop->resp[0], stop->resp[1], stop->resp[2],
441 stop->resp[3], stop->error);
442 }
443
444 spin_unlock_bh(&slot->host->lock);
445
446 return 0;
447}
448
449DEFINE_SHOW_ATTRIBUTE(atmci_req);
450
451static void atmci_show_status_reg(struct seq_file *s,
452 const char *regname, u32 value)
453{
454 static const char *sr_bit[] = {
455 [0] = "CMDRDY",
456 [1] = "RXRDY",
457 [2] = "TXRDY",
458 [3] = "BLKE",
459 [4] = "DTIP",
460 [5] = "NOTBUSY",
461 [6] = "ENDRX",
462 [7] = "ENDTX",
463 [8] = "SDIOIRQA",
464 [9] = "SDIOIRQB",
465 [12] = "SDIOWAIT",
466 [14] = "RXBUFF",
467 [15] = "TXBUFE",
468 [16] = "RINDE",
469 [17] = "RDIRE",
470 [18] = "RCRCE",
471 [19] = "RENDE",
472 [20] = "RTOE",
473 [21] = "DCRCE",
474 [22] = "DTOE",
475 [23] = "CSTOE",
476 [24] = "BLKOVRE",
477 [25] = "DMADONE",
478 [26] = "FIFOEMPTY",
479 [27] = "XFRDONE",
480 [30] = "OVRE",
481 [31] = "UNRE",
482 };
483 unsigned int i;
484
485 seq_printf(s, "%s:\t0x%08x", regname, value);
486 for (i = 0; i < ARRAY_SIZE(sr_bit); i++) {
487 if (value & (1 << i)) {
488 if (sr_bit[i])
489 seq_printf(s, " %s", sr_bit[i]);
490 else
491 seq_puts(s, " UNKNOWN");
492 }
493 }
494 seq_putc(s, '\n');
495}
496
497static int atmci_regs_show(struct seq_file *s, void *v)
498{
499 struct atmel_mci *host = s->private;
500 u32 *buf;
501 int ret = 0;
502
503
504 buf = kmalloc(ATMCI_REGS_SIZE, GFP_KERNEL);
505 if (!buf)
506 return -ENOMEM;
507
508 pm_runtime_get_sync(&host->pdev->dev);
509
510 /*
511 * Grab a more or less consistent snapshot. Note that we're
512 * not disabling interrupts, so IMR and SR may not be
513 * consistent.
514 */
515 spin_lock_bh(&host->lock);
516 memcpy_fromio(buf, host->regs, ATMCI_REGS_SIZE);
517 spin_unlock_bh(&host->lock);
518
519 pm_runtime_mark_last_busy(&host->pdev->dev);
520 pm_runtime_put_autosuspend(&host->pdev->dev);
521
522 seq_printf(s, "MR:\t0x%08x%s%s ",
523 buf[ATMCI_MR / 4],
524 buf[ATMCI_MR / 4] & ATMCI_MR_RDPROOF ? " RDPROOF" : "",
525 buf[ATMCI_MR / 4] & ATMCI_MR_WRPROOF ? " WRPROOF" : "");
526 if (host->caps.has_odd_clk_div)
527 seq_printf(s, "{CLKDIV,CLKODD}=%u\n",
528 ((buf[ATMCI_MR / 4] & 0xff) << 1)
529 | ((buf[ATMCI_MR / 4] >> 16) & 1));
530 else
531 seq_printf(s, "CLKDIV=%u\n",
532 (buf[ATMCI_MR / 4] & 0xff));
533 seq_printf(s, "DTOR:\t0x%08x\n", buf[ATMCI_DTOR / 4]);
534 seq_printf(s, "SDCR:\t0x%08x\n", buf[ATMCI_SDCR / 4]);
535 seq_printf(s, "ARGR:\t0x%08x\n", buf[ATMCI_ARGR / 4]);
536 seq_printf(s, "BLKR:\t0x%08x BCNT=%u BLKLEN=%u\n",
537 buf[ATMCI_BLKR / 4],
538 buf[ATMCI_BLKR / 4] & 0xffff,
539 (buf[ATMCI_BLKR / 4] >> 16) & 0xffff);
540 if (host->caps.has_cstor_reg)
541 seq_printf(s, "CSTOR:\t0x%08x\n", buf[ATMCI_CSTOR / 4]);
542
543 /* Don't read RSPR and RDR; it will consume the data there */
544
545 atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]);
546 atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]);
547
548 if (host->caps.has_dma_conf_reg) {
549 u32 val;
550
551 val = buf[ATMCI_DMA / 4];
552 seq_printf(s, "DMA:\t0x%08x OFFSET=%u CHKSIZE=%u%s\n",
553 val, val & 3,
554 ((val >> 4) & 3) ?
555 1 << (((val >> 4) & 3) + 1) : 1,
556 val & ATMCI_DMAEN ? " DMAEN" : "");
557 }
558 if (host->caps.has_cfg_reg) {
559 u32 val;
560
561 val = buf[ATMCI_CFG / 4];
562 seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n",
563 val,
564 val & ATMCI_CFG_FIFOMODE_1DATA ? " FIFOMODE_ONE_DATA" : "",
565 val & ATMCI_CFG_FERRCTRL_COR ? " FERRCTRL_CLEAR_ON_READ" : "",
566 val & ATMCI_CFG_HSMODE ? " HSMODE" : "",
567 val & ATMCI_CFG_LSYNC ? " LSYNC" : "");
568 }
569
570 kfree(buf);
571
572 return ret;
573}
574
575DEFINE_SHOW_ATTRIBUTE(atmci_regs);
576
577static void atmci_init_debugfs(struct atmel_mci_slot *slot)
578{
579 struct mmc_host *mmc = slot->mmc;
580 struct atmel_mci *host = slot->host;
581 struct dentry *root;
582
583 root = mmc->debugfs_root;
584 if (!root)
585 return;
586
587 debugfs_create_file("regs", S_IRUSR, root, host, &atmci_regs_fops);
588 debugfs_create_file("req", S_IRUSR, root, slot, &atmci_req_fops);
589 debugfs_create_u32("state", S_IRUSR, root, &host->state);
590 debugfs_create_xul("pending_events", S_IRUSR, root,
591 &host->pending_events);
592 debugfs_create_xul("completed_events", S_IRUSR, root,
593 &host->completed_events);
594}
595
596#if defined(CONFIG_OF)
597static const struct of_device_id atmci_dt_ids[] = {
598 { .compatible = "atmel,hsmci" },
599 { /* sentinel */ }
600};
601
602MODULE_DEVICE_TABLE(of, atmci_dt_ids);
603
604static struct mci_platform_data*
605atmci_of_init(struct platform_device *pdev)
606{
607 struct device_node *np = pdev->dev.of_node;
608 struct device_node *cnp;
609 struct mci_platform_data *pdata;
610 u32 slot_id;
611
612 if (!np) {
613 dev_err(&pdev->dev, "device node not found\n");
614 return ERR_PTR(-EINVAL);
615 }
616
617 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
618 if (!pdata)
619 return ERR_PTR(-ENOMEM);
620
621 for_each_child_of_node(np, cnp) {
622 if (of_property_read_u32(cnp, "reg", &slot_id)) {
623 dev_warn(&pdev->dev, "reg property is missing for %pOF\n",
624 cnp);
625 continue;
626 }
627
628 if (slot_id >= ATMCI_MAX_NR_SLOTS) {
629 dev_warn(&pdev->dev, "can't have more than %d slots\n",
630 ATMCI_MAX_NR_SLOTS);
631 of_node_put(cnp);
632 break;
633 }
634
635 if (of_property_read_u32(cnp, "bus-width",
636 &pdata->slot[slot_id].bus_width))
637 pdata->slot[slot_id].bus_width = 1;
638
639 pdata->slot[slot_id].detect_pin =
640 of_get_named_gpio(cnp, "cd-gpios", 0);
641
642 pdata->slot[slot_id].detect_is_active_high =
643 of_property_read_bool(cnp, "cd-inverted");
644
645 pdata->slot[slot_id].non_removable =
646 of_property_read_bool(cnp, "non-removable");
647
648 pdata->slot[slot_id].wp_pin =
649 of_get_named_gpio(cnp, "wp-gpios", 0);
650 }
651
652 return pdata;
653}
654#else /* CONFIG_OF */
655static inline struct mci_platform_data*
656atmci_of_init(struct platform_device *dev)
657{
658 return ERR_PTR(-EINVAL);
659}
660#endif
661
662static inline unsigned int atmci_get_version(struct atmel_mci *host)
663{
664 return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
665}
666
667/*
668 * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
669 * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
670 * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
671 * 8 -> 3, 16 -> 4.
672 *
673 * This can be done by finding most significant bit set.
674 */
675static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
676 unsigned int maxburst)
677{
678 unsigned int version = atmci_get_version(host);
679 unsigned int offset = 2;
680
681 if (version >= 0x600)
682 offset = 1;
683
684 if (maxburst > 1)
685 return fls(maxburst) - offset;
686 else
687 return 0;
688}
689
690static void atmci_timeout_timer(struct timer_list *t)
691{
692 struct atmel_mci *host;
693
694 host = from_timer(host, t, timer);
695
696 dev_dbg(&host->pdev->dev, "software timeout\n");
697
698 if (host->mrq->cmd->data) {
699 host->mrq->cmd->data->error = -ETIMEDOUT;
700 host->data = NULL;
701 /*
702 * With some SDIO modules, sometimes DMA transfer hangs. If
703 * stop_transfer() is not called then the DMA request is not
704 * removed, following ones are queued and never computed.
705 */
706 if (host->state == STATE_DATA_XFER)
707 host->stop_transfer(host);
708 } else {
709 host->mrq->cmd->error = -ETIMEDOUT;
710 host->cmd = NULL;
711 }
712 host->need_reset = 1;
713 host->state = STATE_END_REQUEST;
714 smp_wmb();
715 tasklet_schedule(&host->tasklet);
716}
717
718static inline unsigned int atmci_ns_to_clocks(struct atmel_mci *host,
719 unsigned int ns)
720{
721 /*
722 * It is easier here to use us instead of ns for the timeout,
723 * it prevents from overflows during calculation.
724 */
725 unsigned int us = DIV_ROUND_UP(ns, 1000);
726
727 /* Maximum clock frequency is host->bus_hz/2 */
728 return us * (DIV_ROUND_UP(host->bus_hz, 2000000));
729}
730
731static void atmci_set_timeout(struct atmel_mci *host,
732 struct atmel_mci_slot *slot, struct mmc_data *data)
733{
734 static unsigned dtomul_to_shift[] = {
735 0, 4, 7, 8, 10, 12, 16, 20
736 };
737 unsigned timeout;
738 unsigned dtocyc;
739 unsigned dtomul;
740
741 timeout = atmci_ns_to_clocks(host, data->timeout_ns)
742 + data->timeout_clks;
743
744 for (dtomul = 0; dtomul < 8; dtomul++) {
745 unsigned shift = dtomul_to_shift[dtomul];
746 dtocyc = (timeout + (1 << shift) - 1) >> shift;
747 if (dtocyc < 15)
748 break;
749 }
750
751 if (dtomul >= 8) {
752 dtomul = 7;
753 dtocyc = 15;
754 }
755
756 dev_vdbg(&slot->mmc->class_dev, "setting timeout to %u cycles\n",
757 dtocyc << dtomul_to_shift[dtomul]);
758 atmci_writel(host, ATMCI_DTOR, (ATMCI_DTOMUL(dtomul) | ATMCI_DTOCYC(dtocyc)));
759}
760
761/*
762 * Return mask with command flags to be enabled for this command.
763 */
764static u32 atmci_prepare_command(struct mmc_host *mmc,
765 struct mmc_command *cmd)
766{
767 struct mmc_data *data;
768 u32 cmdr;
769
770 cmd->error = -EINPROGRESS;
771
772 cmdr = ATMCI_CMDR_CMDNB(cmd->opcode);
773
774 if (cmd->flags & MMC_RSP_PRESENT) {
775 if (cmd->flags & MMC_RSP_136)
776 cmdr |= ATMCI_CMDR_RSPTYP_136BIT;
777 else
778 cmdr |= ATMCI_CMDR_RSPTYP_48BIT;
779 }
780
781 /*
782 * This should really be MAXLAT_5 for CMD2 and ACMD41, but
783 * it's too difficult to determine whether this is an ACMD or
784 * not. Better make it 64.
785 */
786 cmdr |= ATMCI_CMDR_MAXLAT_64CYC;
787
788 if (mmc->ios.bus_mode == MMC_BUSMODE_OPENDRAIN)
789 cmdr |= ATMCI_CMDR_OPDCMD;
790
791 data = cmd->data;
792 if (data) {
793 cmdr |= ATMCI_CMDR_START_XFER;
794
795 if (cmd->opcode == SD_IO_RW_EXTENDED) {
796 cmdr |= ATMCI_CMDR_SDIO_BLOCK;
797 } else {
798 if (data->blocks > 1)
799 cmdr |= ATMCI_CMDR_MULTI_BLOCK;
800 else
801 cmdr |= ATMCI_CMDR_BLOCK;
802 }
803
804 if (data->flags & MMC_DATA_READ)
805 cmdr |= ATMCI_CMDR_TRDIR_READ;
806 }
807
808 return cmdr;
809}
810
811static void atmci_send_command(struct atmel_mci *host,
812 struct mmc_command *cmd, u32 cmd_flags)
813{
814 unsigned int timeout_ms = cmd->busy_timeout ? cmd->busy_timeout :
815 ATMCI_CMD_TIMEOUT_MS;
816
817 WARN_ON(host->cmd);
818 host->cmd = cmd;
819
820 dev_vdbg(&host->pdev->dev,
821 "start command: ARGR=0x%08x CMDR=0x%08x\n",
822 cmd->arg, cmd_flags);
823
824 atmci_writel(host, ATMCI_ARGR, cmd->arg);
825 atmci_writel(host, ATMCI_CMDR, cmd_flags);
826
827 mod_timer(&host->timer, jiffies + msecs_to_jiffies(timeout_ms));
828}
829
830static void atmci_send_stop_cmd(struct atmel_mci *host, struct mmc_data *data)
831{
832 dev_dbg(&host->pdev->dev, "send stop command\n");
833 atmci_send_command(host, data->stop, host->stop_cmdr);
834 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
835}
836
837/*
838 * Configure given PDC buffer taking care of alignement issues.
839 * Update host->data_size and host->sg.
840 */
841static void atmci_pdc_set_single_buf(struct atmel_mci *host,
842 enum atmci_xfer_dir dir, enum atmci_pdc_buf buf_nb)
843{
844 u32 pointer_reg, counter_reg;
845 unsigned int buf_size;
846
847 if (dir == XFER_RECEIVE) {
848 pointer_reg = ATMEL_PDC_RPR;
849 counter_reg = ATMEL_PDC_RCR;
850 } else {
851 pointer_reg = ATMEL_PDC_TPR;
852 counter_reg = ATMEL_PDC_TCR;
853 }
854
855 if (buf_nb == PDC_SECOND_BUF) {
856 pointer_reg += ATMEL_PDC_SCND_BUF_OFF;
857 counter_reg += ATMEL_PDC_SCND_BUF_OFF;
858 }
859
860 if (!host->caps.has_rwproof) {
861 buf_size = host->buf_size;
862 atmci_writel(host, pointer_reg, host->buf_phys_addr);
863 } else {
864 buf_size = sg_dma_len(host->sg);
865 atmci_writel(host, pointer_reg, sg_dma_address(host->sg));
866 }
867
868 if (host->data_size <= buf_size) {
869 if (host->data_size & 0x3) {
870 /* If size is different from modulo 4, transfer bytes */
871 atmci_writel(host, counter_reg, host->data_size);
872 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCFBYTE);
873 } else {
874 /* Else transfer 32-bits words */
875 atmci_writel(host, counter_reg, host->data_size / 4);
876 }
877 host->data_size = 0;
878 } else {
879 /* We assume the size of a page is 32-bits aligned */
880 atmci_writel(host, counter_reg, sg_dma_len(host->sg) / 4);
881 host->data_size -= sg_dma_len(host->sg);
882 if (host->data_size)
883 host->sg = sg_next(host->sg);
884 }
885}
886
887/*
888 * Configure PDC buffer according to the data size ie configuring one or two
889 * buffers. Don't use this function if you want to configure only the second
890 * buffer. In this case, use atmci_pdc_set_single_buf.
891 */
892static void atmci_pdc_set_both_buf(struct atmel_mci *host, int dir)
893{
894 atmci_pdc_set_single_buf(host, dir, PDC_FIRST_BUF);
895 if (host->data_size)
896 atmci_pdc_set_single_buf(host, dir, PDC_SECOND_BUF);
897}
898
899/*
900 * Unmap sg lists, called when transfer is finished.
901 */
902static void atmci_pdc_cleanup(struct atmel_mci *host)
903{
904 struct mmc_data *data = host->data;
905
906 if (data)
907 dma_unmap_sg(&host->pdev->dev,
908 data->sg, data->sg_len,
909 mmc_get_dma_dir(data));
910}
911
912/*
913 * Disable PDC transfers. Update pending flags to EVENT_XFER_COMPLETE after
914 * having received ATMCI_TXBUFE or ATMCI_RXBUFF interrupt. Enable ATMCI_NOTBUSY
915 * interrupt needed for both transfer directions.
916 */
917static void atmci_pdc_complete(struct atmel_mci *host)
918{
919 int transfer_size = host->data->blocks * host->data->blksz;
920 int i;
921
922 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
923
924 if ((!host->caps.has_rwproof)
925 && (host->data->flags & MMC_DATA_READ)) {
926 if (host->caps.has_bad_data_ordering)
927 for (i = 0; i < transfer_size; i++)
928 host->buffer[i] = swab32(host->buffer[i]);
929 sg_copy_from_buffer(host->data->sg, host->data->sg_len,
930 host->buffer, transfer_size);
931 }
932
933 atmci_pdc_cleanup(host);
934
935 dev_dbg(&host->pdev->dev, "(%s) set pending xfer complete\n", __func__);
936 atmci_set_pending(host, EVENT_XFER_COMPLETE);
937 tasklet_schedule(&host->tasklet);
938}
939
940static void atmci_dma_cleanup(struct atmel_mci *host)
941{
942 struct mmc_data *data = host->data;
943
944 if (data)
945 dma_unmap_sg(host->dma.chan->device->dev,
946 data->sg, data->sg_len,
947 mmc_get_dma_dir(data));
948}
949
950/*
951 * This function is called by the DMA driver from tasklet context.
952 */
953static void atmci_dma_complete(void *arg)
954{
955 struct atmel_mci *host = arg;
956 struct mmc_data *data = host->data;
957
958 dev_vdbg(&host->pdev->dev, "DMA complete\n");
959
960 if (host->caps.has_dma_conf_reg)
961 /* Disable DMA hardware handshaking on MCI */
962 atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN);
963
964 atmci_dma_cleanup(host);
965
966 /*
967 * If the card was removed, data will be NULL. No point trying
968 * to send the stop command or waiting for NBUSY in this case.
969 */
970 if (data) {
971 dev_dbg(&host->pdev->dev,
972 "(%s) set pending xfer complete\n", __func__);
973 atmci_set_pending(host, EVENT_XFER_COMPLETE);
974 tasklet_schedule(&host->tasklet);
975
976 /*
977 * Regardless of what the documentation says, we have
978 * to wait for NOTBUSY even after block read
979 * operations.
980 *
981 * When the DMA transfer is complete, the controller
982 * may still be reading the CRC from the card, i.e.
983 * the data transfer is still in progress and we
984 * haven't seen all the potential error bits yet.
985 *
986 * The interrupt handler will schedule a different
987 * tasklet to finish things up when the data transfer
988 * is completely done.
989 *
990 * We may not complete the mmc request here anyway
991 * because the mmc layer may call back and cause us to
992 * violate the "don't submit new operations from the
993 * completion callback" rule of the dma engine
994 * framework.
995 */
996 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
997 }
998}
999
1000/*
1001 * Returns a mask of interrupt flags to be enabled after the whole
1002 * request has been prepared.
1003 */
1004static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
1005{
1006 u32 iflags;
1007
1008 data->error = -EINPROGRESS;
1009
1010 host->sg = data->sg;
1011 host->sg_len = data->sg_len;
1012 host->data = data;
1013 host->data_chan = NULL;
1014
1015 iflags = ATMCI_DATA_ERROR_FLAGS;
1016
1017 /*
1018 * Errata: MMC data write operation with less than 12
1019 * bytes is impossible.
1020 *
1021 * Errata: MCI Transmit Data Register (TDR) FIFO
1022 * corruption when length is not multiple of 4.
1023 */
1024 if (data->blocks * data->blksz < 12
1025 || (data->blocks * data->blksz) & 3)
1026 host->need_reset = true;
1027
1028 host->pio_offset = 0;
1029 if (data->flags & MMC_DATA_READ)
1030 iflags |= ATMCI_RXRDY;
1031 else
1032 iflags |= ATMCI_TXRDY;
1033
1034 return iflags;
1035}
1036
1037/*
1038 * Set interrupt flags and set block length into the MCI mode register even
1039 * if this value is also accessible in the MCI block register. It seems to be
1040 * necessary before the High Speed MCI version. It also map sg and configure
1041 * PDC registers.
1042 */
1043static u32
1044atmci_prepare_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1045{
1046 u32 iflags, tmp;
1047 int i;
1048
1049 data->error = -EINPROGRESS;
1050
1051 host->data = data;
1052 host->sg = data->sg;
1053 iflags = ATMCI_DATA_ERROR_FLAGS;
1054
1055 /* Enable pdc mode */
1056 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCMODE);
1057
1058 if (data->flags & MMC_DATA_READ)
1059 iflags |= ATMCI_ENDRX | ATMCI_RXBUFF;
1060 else
1061 iflags |= ATMCI_ENDTX | ATMCI_TXBUFE | ATMCI_BLKE;
1062
1063 /* Set BLKLEN */
1064 tmp = atmci_readl(host, ATMCI_MR);
1065 tmp &= 0x0000ffff;
1066 tmp |= ATMCI_BLKLEN(data->blksz);
1067 atmci_writel(host, ATMCI_MR, tmp);
1068
1069 /* Configure PDC */
1070 host->data_size = data->blocks * data->blksz;
1071 dma_map_sg(&host->pdev->dev, data->sg, data->sg_len,
1072 mmc_get_dma_dir(data));
1073
1074 if ((!host->caps.has_rwproof)
1075 && (host->data->flags & MMC_DATA_WRITE)) {
1076 sg_copy_to_buffer(host->data->sg, host->data->sg_len,
1077 host->buffer, host->data_size);
1078 if (host->caps.has_bad_data_ordering)
1079 for (i = 0; i < host->data_size; i++)
1080 host->buffer[i] = swab32(host->buffer[i]);
1081 }
1082
1083 if (host->data_size)
1084 atmci_pdc_set_both_buf(host, data->flags & MMC_DATA_READ ?
1085 XFER_RECEIVE : XFER_TRANSMIT);
1086 return iflags;
1087}
1088
1089static u32
1090atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
1091{
1092 struct dma_chan *chan;
1093 struct dma_async_tx_descriptor *desc;
1094 struct scatterlist *sg;
1095 unsigned int i;
1096 enum dma_transfer_direction slave_dirn;
1097 unsigned int sglen;
1098 u32 maxburst;
1099 u32 iflags;
1100
1101 data->error = -EINPROGRESS;
1102
1103 WARN_ON(host->data);
1104 host->sg = NULL;
1105 host->data = data;
1106
1107 iflags = ATMCI_DATA_ERROR_FLAGS;
1108
1109 /*
1110 * We don't do DMA on "complex" transfers, i.e. with
1111 * non-word-aligned buffers or lengths. Also, we don't bother
1112 * with all the DMA setup overhead for short transfers.
1113 */
1114 if (data->blocks * data->blksz < ATMCI_DMA_THRESHOLD)
1115 return atmci_prepare_data(host, data);
1116 if (data->blksz & 3)
1117 return atmci_prepare_data(host, data);
1118
1119 for_each_sg(data->sg, sg, data->sg_len, i) {
1120 if (sg->offset & 3 || sg->length & 3)
1121 return atmci_prepare_data(host, data);
1122 }
1123
1124 /* If we don't have a channel, we can't do DMA */
1125 if (!host->dma.chan)
1126 return -ENODEV;
1127
1128 chan = host->dma.chan;
1129 host->data_chan = chan;
1130
1131 if (data->flags & MMC_DATA_READ) {
1132 host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
1133 maxburst = atmci_convert_chksize(host,
1134 host->dma_conf.src_maxburst);
1135 } else {
1136 host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
1137 maxburst = atmci_convert_chksize(host,
1138 host->dma_conf.dst_maxburst);
1139 }
1140
1141 if (host->caps.has_dma_conf_reg)
1142 atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) |
1143 ATMCI_DMAEN);
1144
1145 sglen = dma_map_sg(chan->device->dev, data->sg,
1146 data->sg_len, mmc_get_dma_dir(data));
1147
1148 dmaengine_slave_config(chan, &host->dma_conf);
1149 desc = dmaengine_prep_slave_sg(chan,
1150 data->sg, sglen, slave_dirn,
1151 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1152 if (!desc)
1153 goto unmap_exit;
1154
1155 host->dma.data_desc = desc;
1156 desc->callback = atmci_dma_complete;
1157 desc->callback_param = host;
1158
1159 return iflags;
1160unmap_exit:
1161 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len,
1162 mmc_get_dma_dir(data));
1163 return -ENOMEM;
1164}
1165
1166static void
1167atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
1168{
1169 return;
1170}
1171
1172/*
1173 * Start PDC according to transfer direction.
1174 */
1175static void
1176atmci_submit_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1177{
1178 if (data->flags & MMC_DATA_READ)
1179 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1180 else
1181 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1182}
1183
1184static void
1185atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
1186{
1187 struct dma_chan *chan = host->data_chan;
1188 struct dma_async_tx_descriptor *desc = host->dma.data_desc;
1189
1190 if (chan) {
1191 dmaengine_submit(desc);
1192 dma_async_issue_pending(chan);
1193 }
1194}
1195
1196static void atmci_stop_transfer(struct atmel_mci *host)
1197{
1198 dev_dbg(&host->pdev->dev,
1199 "(%s) set pending xfer complete\n", __func__);
1200 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1201 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1202}
1203
1204/*
1205 * Stop data transfer because error(s) occurred.
1206 */
1207static void atmci_stop_transfer_pdc(struct atmel_mci *host)
1208{
1209 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
1210}
1211
1212static void atmci_stop_transfer_dma(struct atmel_mci *host)
1213{
1214 struct dma_chan *chan = host->data_chan;
1215
1216 if (chan) {
1217 dmaengine_terminate_all(chan);
1218 atmci_dma_cleanup(host);
1219 } else {
1220 /* Data transfer was stopped by the interrupt handler */
1221 dev_dbg(&host->pdev->dev,
1222 "(%s) set pending xfer complete\n", __func__);
1223 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1224 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1225 }
1226}
1227
1228/*
1229 * Start a request: prepare data if needed, prepare the command and activate
1230 * interrupts.
1231 */
1232static void atmci_start_request(struct atmel_mci *host,
1233 struct atmel_mci_slot *slot)
1234{
1235 struct mmc_request *mrq;
1236 struct mmc_command *cmd;
1237 struct mmc_data *data;
1238 u32 iflags;
1239 u32 cmdflags;
1240
1241 mrq = slot->mrq;
1242 host->cur_slot = slot;
1243 host->mrq = mrq;
1244
1245 host->pending_events = 0;
1246 host->completed_events = 0;
1247 host->cmd_status = 0;
1248 host->data_status = 0;
1249
1250 dev_dbg(&host->pdev->dev, "start request: cmd %u\n", mrq->cmd->opcode);
1251
1252 if (host->need_reset || host->caps.need_reset_after_xfer) {
1253 iflags = atmci_readl(host, ATMCI_IMR);
1254 iflags &= (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB);
1255 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1256 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1257 atmci_writel(host, ATMCI_MR, host->mode_reg);
1258 if (host->caps.has_cfg_reg)
1259 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1260 atmci_writel(host, ATMCI_IER, iflags);
1261 host->need_reset = false;
1262 }
1263 atmci_writel(host, ATMCI_SDCR, slot->sdc_reg);
1264
1265 iflags = atmci_readl(host, ATMCI_IMR);
1266 if (iflags & ~(ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
1267 dev_dbg(&slot->mmc->class_dev, "WARNING: IMR=0x%08x\n",
1268 iflags);
1269
1270 if (unlikely(test_and_clear_bit(ATMCI_CARD_NEED_INIT, &slot->flags))) {
1271 /* Send init sequence (74 clock cycles) */
1272 atmci_writel(host, ATMCI_CMDR, ATMCI_CMDR_SPCMD_INIT);
1273 while (!(atmci_readl(host, ATMCI_SR) & ATMCI_CMDRDY))
1274 cpu_relax();
1275 }
1276 iflags = 0;
1277 data = mrq->data;
1278 if (data) {
1279 atmci_set_timeout(host, slot, data);
1280
1281 /* Must set block count/size before sending command */
1282 atmci_writel(host, ATMCI_BLKR, ATMCI_BCNT(data->blocks)
1283 | ATMCI_BLKLEN(data->blksz));
1284 dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n",
1285 ATMCI_BCNT(data->blocks) | ATMCI_BLKLEN(data->blksz));
1286
1287 iflags |= host->prepare_data(host, data);
1288 }
1289
1290 iflags |= ATMCI_CMDRDY;
1291 cmd = mrq->cmd;
1292 cmdflags = atmci_prepare_command(slot->mmc, cmd);
1293
1294 /*
1295 * DMA transfer should be started before sending the command to avoid
1296 * unexpected errors especially for read operations in SDIO mode.
1297 * Unfortunately, in PDC mode, command has to be sent before starting
1298 * the transfer.
1299 */
1300 if (host->submit_data != &atmci_submit_data_dma)
1301 atmci_send_command(host, cmd, cmdflags);
1302
1303 if (data)
1304 host->submit_data(host, data);
1305
1306 if (host->submit_data == &atmci_submit_data_dma)
1307 atmci_send_command(host, cmd, cmdflags);
1308
1309 if (mrq->stop) {
1310 host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop);
1311 host->stop_cmdr |= ATMCI_CMDR_STOP_XFER;
1312 if (!(data->flags & MMC_DATA_WRITE))
1313 host->stop_cmdr |= ATMCI_CMDR_TRDIR_READ;
1314 host->stop_cmdr |= ATMCI_CMDR_MULTI_BLOCK;
1315 }
1316
1317 /*
1318 * We could have enabled interrupts earlier, but I suspect
1319 * that would open up a nice can of interesting race
1320 * conditions (e.g. command and data complete, but stop not
1321 * prepared yet.)
1322 */
1323 atmci_writel(host, ATMCI_IER, iflags);
1324}
1325
1326static void atmci_queue_request(struct atmel_mci *host,
1327 struct atmel_mci_slot *slot, struct mmc_request *mrq)
1328{
1329 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1330 host->state);
1331
1332 spin_lock_bh(&host->lock);
1333 slot->mrq = mrq;
1334 if (host->state == STATE_IDLE) {
1335 host->state = STATE_SENDING_CMD;
1336 atmci_start_request(host, slot);
1337 } else {
1338 dev_dbg(&host->pdev->dev, "queue request\n");
1339 list_add_tail(&slot->queue_node, &host->queue);
1340 }
1341 spin_unlock_bh(&host->lock);
1342}
1343
1344static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1345{
1346 struct atmel_mci_slot *slot = mmc_priv(mmc);
1347 struct atmel_mci *host = slot->host;
1348 struct mmc_data *data;
1349
1350 WARN_ON(slot->mrq);
1351 dev_dbg(&host->pdev->dev, "MRQ: cmd %u\n", mrq->cmd->opcode);
1352
1353 /*
1354 * We may "know" the card is gone even though there's still an
1355 * electrical connection. If so, we really need to communicate
1356 * this to the MMC core since there won't be any more
1357 * interrupts as the card is completely removed. Otherwise,
1358 * the MMC core might believe the card is still there even
1359 * though the card was just removed very slowly.
1360 */
1361 if (!test_bit(ATMCI_CARD_PRESENT, &slot->flags)) {
1362 mrq->cmd->error = -ENOMEDIUM;
1363 mmc_request_done(mmc, mrq);
1364 return;
1365 }
1366
1367 /* We don't support multiple blocks of weird lengths. */
1368 data = mrq->data;
1369 if (data && data->blocks > 1 && data->blksz & 3) {
1370 mrq->cmd->error = -EINVAL;
1371 mmc_request_done(mmc, mrq);
1372 }
1373
1374 atmci_queue_request(host, slot, mrq);
1375}
1376
1377static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1378{
1379 struct atmel_mci_slot *slot = mmc_priv(mmc);
1380 struct atmel_mci *host = slot->host;
1381 unsigned int i;
1382
1383 slot->sdc_reg &= ~ATMCI_SDCBUS_MASK;
1384 switch (ios->bus_width) {
1385 case MMC_BUS_WIDTH_1:
1386 slot->sdc_reg |= ATMCI_SDCBUS_1BIT;
1387 break;
1388 case MMC_BUS_WIDTH_4:
1389 slot->sdc_reg |= ATMCI_SDCBUS_4BIT;
1390 break;
1391 case MMC_BUS_WIDTH_8:
1392 slot->sdc_reg |= ATMCI_SDCBUS_8BIT;
1393 break;
1394 }
1395
1396 if (ios->clock) {
1397 unsigned int clock_min = ~0U;
1398 int clkdiv;
1399
1400 spin_lock_bh(&host->lock);
1401 if (!host->mode_reg) {
1402 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1403 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1404 if (host->caps.has_cfg_reg)
1405 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1406 }
1407
1408 /*
1409 * Use mirror of ios->clock to prevent race with mmc
1410 * core ios update when finding the minimum.
1411 */
1412 slot->clock = ios->clock;
1413 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1414 if (host->slot[i] && host->slot[i]->clock
1415 && host->slot[i]->clock < clock_min)
1416 clock_min = host->slot[i]->clock;
1417 }
1418
1419 /* Calculate clock divider */
1420 if (host->caps.has_odd_clk_div) {
1421 clkdiv = DIV_ROUND_UP(host->bus_hz, clock_min) - 2;
1422 if (clkdiv < 0) {
1423 dev_warn(&mmc->class_dev,
1424 "clock %u too fast; using %lu\n",
1425 clock_min, host->bus_hz / 2);
1426 clkdiv = 0;
1427 } else if (clkdiv > 511) {
1428 dev_warn(&mmc->class_dev,
1429 "clock %u too slow; using %lu\n",
1430 clock_min, host->bus_hz / (511 + 2));
1431 clkdiv = 511;
1432 }
1433 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv >> 1)
1434 | ATMCI_MR_CLKODD(clkdiv & 1);
1435 } else {
1436 clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * clock_min) - 1;
1437 if (clkdiv > 255) {
1438 dev_warn(&mmc->class_dev,
1439 "clock %u too slow; using %lu\n",
1440 clock_min, host->bus_hz / (2 * 256));
1441 clkdiv = 255;
1442 }
1443 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv);
1444 }
1445
1446 /*
1447 * WRPROOF and RDPROOF prevent overruns/underruns by
1448 * stopping the clock when the FIFO is full/empty.
1449 * This state is not expected to last for long.
1450 */
1451 if (host->caps.has_rwproof)
1452 host->mode_reg |= (ATMCI_MR_WRPROOF | ATMCI_MR_RDPROOF);
1453
1454 if (host->caps.has_cfg_reg) {
1455 /* setup High Speed mode in relation with card capacity */
1456 if (ios->timing == MMC_TIMING_SD_HS)
1457 host->cfg_reg |= ATMCI_CFG_HSMODE;
1458 else
1459 host->cfg_reg &= ~ATMCI_CFG_HSMODE;
1460 }
1461
1462 if (list_empty(&host->queue)) {
1463 atmci_writel(host, ATMCI_MR, host->mode_reg);
1464 if (host->caps.has_cfg_reg)
1465 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1466 } else {
1467 host->need_clock_update = true;
1468 }
1469
1470 spin_unlock_bh(&host->lock);
1471 } else {
1472 bool any_slot_active = false;
1473
1474 spin_lock_bh(&host->lock);
1475 slot->clock = 0;
1476 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1477 if (host->slot[i] && host->slot[i]->clock) {
1478 any_slot_active = true;
1479 break;
1480 }
1481 }
1482 if (!any_slot_active) {
1483 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
1484 if (host->mode_reg) {
1485 atmci_readl(host, ATMCI_MR);
1486 }
1487 host->mode_reg = 0;
1488 }
1489 spin_unlock_bh(&host->lock);
1490 }
1491
1492 switch (ios->power_mode) {
1493 case MMC_POWER_OFF:
1494 if (!IS_ERR(mmc->supply.vmmc))
1495 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1496 break;
1497 case MMC_POWER_UP:
1498 set_bit(ATMCI_CARD_NEED_INIT, &slot->flags);
1499 if (!IS_ERR(mmc->supply.vmmc))
1500 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
1501 break;
1502 default:
1503 break;
1504 }
1505}
1506
1507static int atmci_get_ro(struct mmc_host *mmc)
1508{
1509 int read_only = -ENOSYS;
1510 struct atmel_mci_slot *slot = mmc_priv(mmc);
1511
1512 if (gpio_is_valid(slot->wp_pin)) {
1513 read_only = gpio_get_value(slot->wp_pin);
1514 dev_dbg(&mmc->class_dev, "card is %s\n",
1515 read_only ? "read-only" : "read-write");
1516 }
1517
1518 return read_only;
1519}
1520
1521static int atmci_get_cd(struct mmc_host *mmc)
1522{
1523 int present = -ENOSYS;
1524 struct atmel_mci_slot *slot = mmc_priv(mmc);
1525
1526 if (gpio_is_valid(slot->detect_pin)) {
1527 present = !(gpio_get_value(slot->detect_pin) ^
1528 slot->detect_is_active_high);
1529 dev_dbg(&mmc->class_dev, "card is %spresent\n",
1530 present ? "" : "not ");
1531 }
1532
1533 return present;
1534}
1535
1536static void atmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1537{
1538 struct atmel_mci_slot *slot = mmc_priv(mmc);
1539 struct atmel_mci *host = slot->host;
1540
1541 if (enable)
1542 atmci_writel(host, ATMCI_IER, slot->sdio_irq);
1543 else
1544 atmci_writel(host, ATMCI_IDR, slot->sdio_irq);
1545}
1546
1547static const struct mmc_host_ops atmci_ops = {
1548 .request = atmci_request,
1549 .set_ios = atmci_set_ios,
1550 .get_ro = atmci_get_ro,
1551 .get_cd = atmci_get_cd,
1552 .enable_sdio_irq = atmci_enable_sdio_irq,
1553};
1554
1555/* Called with host->lock held */
1556static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq)
1557 __releases(&host->lock)
1558 __acquires(&host->lock)
1559{
1560 struct atmel_mci_slot *slot = NULL;
1561 struct mmc_host *prev_mmc = host->cur_slot->mmc;
1562
1563 WARN_ON(host->cmd || host->data);
1564
1565 del_timer(&host->timer);
1566
1567 /*
1568 * Update the MMC clock rate if necessary. This may be
1569 * necessary if set_ios() is called when a different slot is
1570 * busy transferring data.
1571 */
1572 if (host->need_clock_update) {
1573 atmci_writel(host, ATMCI_MR, host->mode_reg);
1574 if (host->caps.has_cfg_reg)
1575 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1576 }
1577
1578 host->cur_slot->mrq = NULL;
1579 host->mrq = NULL;
1580 if (!list_empty(&host->queue)) {
1581 slot = list_entry(host->queue.next,
1582 struct atmel_mci_slot, queue_node);
1583 list_del(&slot->queue_node);
1584 dev_vdbg(&host->pdev->dev, "list not empty: %s is next\n",
1585 mmc_hostname(slot->mmc));
1586 host->state = STATE_SENDING_CMD;
1587 atmci_start_request(host, slot);
1588 } else {
1589 dev_vdbg(&host->pdev->dev, "list empty\n");
1590 host->state = STATE_IDLE;
1591 }
1592
1593 spin_unlock(&host->lock);
1594 mmc_request_done(prev_mmc, mrq);
1595 spin_lock(&host->lock);
1596}
1597
1598static void atmci_command_complete(struct atmel_mci *host,
1599 struct mmc_command *cmd)
1600{
1601 u32 status = host->cmd_status;
1602
1603 /* Read the response from the card (up to 16 bytes) */
1604 cmd->resp[0] = atmci_readl(host, ATMCI_RSPR);
1605 cmd->resp[1] = atmci_readl(host, ATMCI_RSPR);
1606 cmd->resp[2] = atmci_readl(host, ATMCI_RSPR);
1607 cmd->resp[3] = atmci_readl(host, ATMCI_RSPR);
1608
1609 if (status & ATMCI_RTOE)
1610 cmd->error = -ETIMEDOUT;
1611 else if ((cmd->flags & MMC_RSP_CRC) && (status & ATMCI_RCRCE))
1612 cmd->error = -EILSEQ;
1613 else if (status & (ATMCI_RINDE | ATMCI_RDIRE | ATMCI_RENDE))
1614 cmd->error = -EIO;
1615 else if (host->mrq->data && (host->mrq->data->blksz & 3)) {
1616 if (host->caps.need_blksz_mul_4) {
1617 cmd->error = -EINVAL;
1618 host->need_reset = 1;
1619 }
1620 } else
1621 cmd->error = 0;
1622}
1623
1624static void atmci_detect_change(struct timer_list *t)
1625{
1626 struct atmel_mci_slot *slot = from_timer(slot, t, detect_timer);
1627 bool present;
1628 bool present_old;
1629
1630 /*
1631 * atmci_cleanup_slot() sets the ATMCI_SHUTDOWN flag before
1632 * freeing the interrupt. We must not re-enable the interrupt
1633 * if it has been freed, and if we're shutting down, it
1634 * doesn't really matter whether the card is present or not.
1635 */
1636 smp_rmb();
1637 if (test_bit(ATMCI_SHUTDOWN, &slot->flags))
1638 return;
1639
1640 enable_irq(gpio_to_irq(slot->detect_pin));
1641 present = !(gpio_get_value(slot->detect_pin) ^
1642 slot->detect_is_active_high);
1643 present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
1644
1645 dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
1646 present, present_old);
1647
1648 if (present != present_old) {
1649 struct atmel_mci *host = slot->host;
1650 struct mmc_request *mrq;
1651
1652 dev_dbg(&slot->mmc->class_dev, "card %s\n",
1653 present ? "inserted" : "removed");
1654
1655 spin_lock(&host->lock);
1656
1657 if (!present)
1658 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
1659 else
1660 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
1661
1662 /* Clean up queue if present */
1663 mrq = slot->mrq;
1664 if (mrq) {
1665 if (mrq == host->mrq) {
1666 /*
1667 * Reset controller to terminate any ongoing
1668 * commands or data transfers.
1669 */
1670 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1671 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1672 atmci_writel(host, ATMCI_MR, host->mode_reg);
1673 if (host->caps.has_cfg_reg)
1674 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1675
1676 host->data = NULL;
1677 host->cmd = NULL;
1678
1679 switch (host->state) {
1680 case STATE_IDLE:
1681 break;
1682 case STATE_SENDING_CMD:
1683 mrq->cmd->error = -ENOMEDIUM;
1684 if (mrq->data)
1685 host->stop_transfer(host);
1686 break;
1687 case STATE_DATA_XFER:
1688 mrq->data->error = -ENOMEDIUM;
1689 host->stop_transfer(host);
1690 break;
1691 case STATE_WAITING_NOTBUSY:
1692 mrq->data->error = -ENOMEDIUM;
1693 break;
1694 case STATE_SENDING_STOP:
1695 mrq->stop->error = -ENOMEDIUM;
1696 break;
1697 case STATE_END_REQUEST:
1698 break;
1699 }
1700
1701 atmci_request_end(host, mrq);
1702 } else {
1703 list_del(&slot->queue_node);
1704 mrq->cmd->error = -ENOMEDIUM;
1705 if (mrq->data)
1706 mrq->data->error = -ENOMEDIUM;
1707 if (mrq->stop)
1708 mrq->stop->error = -ENOMEDIUM;
1709
1710 spin_unlock(&host->lock);
1711 mmc_request_done(slot->mmc, mrq);
1712 spin_lock(&host->lock);
1713 }
1714 }
1715 spin_unlock(&host->lock);
1716
1717 mmc_detect_change(slot->mmc, 0);
1718 }
1719}
1720
1721static void atmci_tasklet_func(struct tasklet_struct *t)
1722{
1723 struct atmel_mci *host = from_tasklet(host, t, tasklet);
1724 struct mmc_request *mrq = host->mrq;
1725 struct mmc_data *data = host->data;
1726 enum atmel_mci_state state = host->state;
1727 enum atmel_mci_state prev_state;
1728 u32 status;
1729
1730 spin_lock(&host->lock);
1731
1732 state = host->state;
1733
1734 dev_vdbg(&host->pdev->dev,
1735 "tasklet: state %u pending/completed/mask %lx/%lx/%x\n",
1736 state, host->pending_events, host->completed_events,
1737 atmci_readl(host, ATMCI_IMR));
1738
1739 do {
1740 prev_state = state;
1741 dev_dbg(&host->pdev->dev, "FSM: state=%d\n", state);
1742
1743 switch (state) {
1744 case STATE_IDLE:
1745 break;
1746
1747 case STATE_SENDING_CMD:
1748 /*
1749 * Command has been sent, we are waiting for command
1750 * ready. Then we have three next states possible:
1751 * END_REQUEST by default, WAITING_NOTBUSY if it's a
1752 * command needing it or DATA_XFER if there is data.
1753 */
1754 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1755 if (!atmci_test_and_clear_pending(host,
1756 EVENT_CMD_RDY))
1757 break;
1758
1759 dev_dbg(&host->pdev->dev, "set completed cmd ready\n");
1760 host->cmd = NULL;
1761 atmci_set_completed(host, EVENT_CMD_RDY);
1762 atmci_command_complete(host, mrq->cmd);
1763 if (mrq->data) {
1764 dev_dbg(&host->pdev->dev,
1765 "command with data transfer");
1766 /*
1767 * If there is a command error don't start
1768 * data transfer.
1769 */
1770 if (mrq->cmd->error) {
1771 host->stop_transfer(host);
1772 host->data = NULL;
1773 atmci_writel(host, ATMCI_IDR,
1774 ATMCI_TXRDY | ATMCI_RXRDY
1775 | ATMCI_DATA_ERROR_FLAGS);
1776 state = STATE_END_REQUEST;
1777 } else
1778 state = STATE_DATA_XFER;
1779 } else if ((!mrq->data) && (mrq->cmd->flags & MMC_RSP_BUSY)) {
1780 dev_dbg(&host->pdev->dev,
1781 "command response need waiting notbusy");
1782 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1783 state = STATE_WAITING_NOTBUSY;
1784 } else
1785 state = STATE_END_REQUEST;
1786
1787 break;
1788
1789 case STATE_DATA_XFER:
1790 if (atmci_test_and_clear_pending(host,
1791 EVENT_DATA_ERROR)) {
1792 dev_dbg(&host->pdev->dev, "set completed data error\n");
1793 atmci_set_completed(host, EVENT_DATA_ERROR);
1794 state = STATE_END_REQUEST;
1795 break;
1796 }
1797
1798 /*
1799 * A data transfer is in progress. The event expected
1800 * to move to the next state depends of data transfer
1801 * type (PDC or DMA). Once transfer done we can move
1802 * to the next step which is WAITING_NOTBUSY in write
1803 * case and directly SENDING_STOP in read case.
1804 */
1805 dev_dbg(&host->pdev->dev, "FSM: xfer complete?\n");
1806 if (!atmci_test_and_clear_pending(host,
1807 EVENT_XFER_COMPLETE))
1808 break;
1809
1810 dev_dbg(&host->pdev->dev,
1811 "(%s) set completed xfer complete\n",
1812 __func__);
1813 atmci_set_completed(host, EVENT_XFER_COMPLETE);
1814
1815 if (host->caps.need_notbusy_for_read_ops ||
1816 (host->data->flags & MMC_DATA_WRITE)) {
1817 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1818 state = STATE_WAITING_NOTBUSY;
1819 } else if (host->mrq->stop) {
1820 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
1821 atmci_send_stop_cmd(host, data);
1822 state = STATE_SENDING_STOP;
1823 } else {
1824 host->data = NULL;
1825 data->bytes_xfered = data->blocks * data->blksz;
1826 data->error = 0;
1827 state = STATE_END_REQUEST;
1828 }
1829 break;
1830
1831 case STATE_WAITING_NOTBUSY:
1832 /*
1833 * We can be in the state for two reasons: a command
1834 * requiring waiting not busy signal (stop command
1835 * included) or a write operation. In the latest case,
1836 * we need to send a stop command.
1837 */
1838 dev_dbg(&host->pdev->dev, "FSM: not busy?\n");
1839 if (!atmci_test_and_clear_pending(host,
1840 EVENT_NOTBUSY))
1841 break;
1842
1843 dev_dbg(&host->pdev->dev, "set completed not busy\n");
1844 atmci_set_completed(host, EVENT_NOTBUSY);
1845
1846 if (host->data) {
1847 /*
1848 * For some commands such as CMD53, even if
1849 * there is data transfer, there is no stop
1850 * command to send.
1851 */
1852 if (host->mrq->stop) {
1853 atmci_writel(host, ATMCI_IER,
1854 ATMCI_CMDRDY);
1855 atmci_send_stop_cmd(host, data);
1856 state = STATE_SENDING_STOP;
1857 } else {
1858 host->data = NULL;
1859 data->bytes_xfered = data->blocks
1860 * data->blksz;
1861 data->error = 0;
1862 state = STATE_END_REQUEST;
1863 }
1864 } else
1865 state = STATE_END_REQUEST;
1866 break;
1867
1868 case STATE_SENDING_STOP:
1869 /*
1870 * In this state, it is important to set host->data to
1871 * NULL (which is tested in the waiting notbusy state)
1872 * in order to go to the end request state instead of
1873 * sending stop again.
1874 */
1875 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1876 if (!atmci_test_and_clear_pending(host,
1877 EVENT_CMD_RDY))
1878 break;
1879
1880 dev_dbg(&host->pdev->dev, "FSM: cmd ready\n");
1881 host->cmd = NULL;
1882 data->bytes_xfered = data->blocks * data->blksz;
1883 data->error = 0;
1884 atmci_command_complete(host, mrq->stop);
1885 if (mrq->stop->error) {
1886 host->stop_transfer(host);
1887 atmci_writel(host, ATMCI_IDR,
1888 ATMCI_TXRDY | ATMCI_RXRDY
1889 | ATMCI_DATA_ERROR_FLAGS);
1890 state = STATE_END_REQUEST;
1891 } else {
1892 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1893 state = STATE_WAITING_NOTBUSY;
1894 }
1895 host->data = NULL;
1896 break;
1897
1898 case STATE_END_REQUEST:
1899 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY | ATMCI_RXRDY
1900 | ATMCI_DATA_ERROR_FLAGS);
1901 status = host->data_status;
1902 if (unlikely(status)) {
1903 host->stop_transfer(host);
1904 host->data = NULL;
1905 if (data) {
1906 if (status & ATMCI_DTOE) {
1907 data->error = -ETIMEDOUT;
1908 } else if (status & ATMCI_DCRCE) {
1909 data->error = -EILSEQ;
1910 } else {
1911 data->error = -EIO;
1912 }
1913 }
1914 }
1915
1916 atmci_request_end(host, host->mrq);
1917 goto unlock; /* atmci_request_end() sets host->state */
1918 break;
1919 }
1920 } while (state != prev_state);
1921
1922 host->state = state;
1923
1924unlock:
1925 spin_unlock(&host->lock);
1926}
1927
1928static void atmci_read_data_pio(struct atmel_mci *host)
1929{
1930 struct scatterlist *sg = host->sg;
1931 unsigned int offset = host->pio_offset;
1932 struct mmc_data *data = host->data;
1933 u32 value;
1934 u32 status;
1935 unsigned int nbytes = 0;
1936
1937 do {
1938 value = atmci_readl(host, ATMCI_RDR);
1939 if (likely(offset + 4 <= sg->length)) {
1940 sg_pcopy_from_buffer(sg, 1, &value, sizeof(u32), offset);
1941
1942 offset += 4;
1943 nbytes += 4;
1944
1945 if (offset == sg->length) {
1946 flush_dcache_page(sg_page(sg));
1947 host->sg = sg = sg_next(sg);
1948 host->sg_len--;
1949 if (!sg || !host->sg_len)
1950 goto done;
1951
1952 offset = 0;
1953 }
1954 } else {
1955 unsigned int remaining = sg->length - offset;
1956
1957 sg_pcopy_from_buffer(sg, 1, &value, remaining, offset);
1958 nbytes += remaining;
1959
1960 flush_dcache_page(sg_page(sg));
1961 host->sg = sg = sg_next(sg);
1962 host->sg_len--;
1963 if (!sg || !host->sg_len)
1964 goto done;
1965
1966 offset = 4 - remaining;
1967 sg_pcopy_from_buffer(sg, 1, (u8 *)&value + remaining,
1968 offset, 0);
1969 nbytes += offset;
1970 }
1971
1972 status = atmci_readl(host, ATMCI_SR);
1973 if (status & ATMCI_DATA_ERROR_FLAGS) {
1974 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_RXRDY
1975 | ATMCI_DATA_ERROR_FLAGS));
1976 host->data_status = status;
1977 data->bytes_xfered += nbytes;
1978 return;
1979 }
1980 } while (status & ATMCI_RXRDY);
1981
1982 host->pio_offset = offset;
1983 data->bytes_xfered += nbytes;
1984
1985 return;
1986
1987done:
1988 atmci_writel(host, ATMCI_IDR, ATMCI_RXRDY);
1989 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1990 data->bytes_xfered += nbytes;
1991 smp_wmb();
1992 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1993}
1994
1995static void atmci_write_data_pio(struct atmel_mci *host)
1996{
1997 struct scatterlist *sg = host->sg;
1998 unsigned int offset = host->pio_offset;
1999 struct mmc_data *data = host->data;
2000 u32 value;
2001 u32 status;
2002 unsigned int nbytes = 0;
2003
2004 do {
2005 if (likely(offset + 4 <= sg->length)) {
2006 sg_pcopy_to_buffer(sg, 1, &value, sizeof(u32), offset);
2007 atmci_writel(host, ATMCI_TDR, value);
2008
2009 offset += 4;
2010 nbytes += 4;
2011 if (offset == sg->length) {
2012 host->sg = sg = sg_next(sg);
2013 host->sg_len--;
2014 if (!sg || !host->sg_len)
2015 goto done;
2016
2017 offset = 0;
2018 }
2019 } else {
2020 unsigned int remaining = sg->length - offset;
2021
2022 value = 0;
2023 sg_pcopy_to_buffer(sg, 1, &value, remaining, offset);
2024 nbytes += remaining;
2025
2026 host->sg = sg = sg_next(sg);
2027 host->sg_len--;
2028 if (!sg || !host->sg_len) {
2029 atmci_writel(host, ATMCI_TDR, value);
2030 goto done;
2031 }
2032
2033 offset = 4 - remaining;
2034 sg_pcopy_to_buffer(sg, 1, (u8 *)&value + remaining,
2035 offset, 0);
2036 atmci_writel(host, ATMCI_TDR, value);
2037 nbytes += offset;
2038 }
2039
2040 status = atmci_readl(host, ATMCI_SR);
2041 if (status & ATMCI_DATA_ERROR_FLAGS) {
2042 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_TXRDY
2043 | ATMCI_DATA_ERROR_FLAGS));
2044 host->data_status = status;
2045 data->bytes_xfered += nbytes;
2046 return;
2047 }
2048 } while (status & ATMCI_TXRDY);
2049
2050 host->pio_offset = offset;
2051 data->bytes_xfered += nbytes;
2052
2053 return;
2054
2055done:
2056 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY);
2057 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2058 data->bytes_xfered += nbytes;
2059 smp_wmb();
2060 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2061}
2062
2063static void atmci_sdio_interrupt(struct atmel_mci *host, u32 status)
2064{
2065 int i;
2066
2067 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2068 struct atmel_mci_slot *slot = host->slot[i];
2069 if (slot && (status & slot->sdio_irq)) {
2070 mmc_signal_sdio_irq(slot->mmc);
2071 }
2072 }
2073}
2074
2075
2076static irqreturn_t atmci_interrupt(int irq, void *dev_id)
2077{
2078 struct atmel_mci *host = dev_id;
2079 u32 status, mask, pending;
2080 unsigned int pass_count = 0;
2081
2082 do {
2083 status = atmci_readl(host, ATMCI_SR);
2084 mask = atmci_readl(host, ATMCI_IMR);
2085 pending = status & mask;
2086 if (!pending)
2087 break;
2088
2089 if (pending & ATMCI_DATA_ERROR_FLAGS) {
2090 dev_dbg(&host->pdev->dev, "IRQ: data error\n");
2091 atmci_writel(host, ATMCI_IDR, ATMCI_DATA_ERROR_FLAGS
2092 | ATMCI_RXRDY | ATMCI_TXRDY
2093 | ATMCI_ENDRX | ATMCI_ENDTX
2094 | ATMCI_RXBUFF | ATMCI_TXBUFE);
2095
2096 host->data_status = status;
2097 dev_dbg(&host->pdev->dev, "set pending data error\n");
2098 smp_wmb();
2099 atmci_set_pending(host, EVENT_DATA_ERROR);
2100 tasklet_schedule(&host->tasklet);
2101 }
2102
2103 if (pending & ATMCI_TXBUFE) {
2104 dev_dbg(&host->pdev->dev, "IRQ: tx buffer empty\n");
2105 atmci_writel(host, ATMCI_IDR, ATMCI_TXBUFE);
2106 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2107 /*
2108 * We can receive this interruption before having configured
2109 * the second pdc buffer, so we need to reconfigure first and
2110 * second buffers again
2111 */
2112 if (host->data_size) {
2113 atmci_pdc_set_both_buf(host, XFER_TRANSMIT);
2114 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2115 atmci_writel(host, ATMCI_IER, ATMCI_TXBUFE);
2116 } else {
2117 atmci_pdc_complete(host);
2118 }
2119 } else if (pending & ATMCI_ENDTX) {
2120 dev_dbg(&host->pdev->dev, "IRQ: end of tx buffer\n");
2121 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2122
2123 if (host->data_size) {
2124 atmci_pdc_set_single_buf(host,
2125 XFER_TRANSMIT, PDC_SECOND_BUF);
2126 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2127 }
2128 }
2129
2130 if (pending & ATMCI_RXBUFF) {
2131 dev_dbg(&host->pdev->dev, "IRQ: rx buffer full\n");
2132 atmci_writel(host, ATMCI_IDR, ATMCI_RXBUFF);
2133 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2134 /*
2135 * We can receive this interruption before having configured
2136 * the second pdc buffer, so we need to reconfigure first and
2137 * second buffers again
2138 */
2139 if (host->data_size) {
2140 atmci_pdc_set_both_buf(host, XFER_RECEIVE);
2141 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2142 atmci_writel(host, ATMCI_IER, ATMCI_RXBUFF);
2143 } else {
2144 atmci_pdc_complete(host);
2145 }
2146 } else if (pending & ATMCI_ENDRX) {
2147 dev_dbg(&host->pdev->dev, "IRQ: end of rx buffer\n");
2148 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2149
2150 if (host->data_size) {
2151 atmci_pdc_set_single_buf(host,
2152 XFER_RECEIVE, PDC_SECOND_BUF);
2153 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2154 }
2155 }
2156
2157 /*
2158 * First mci IPs, so mainly the ones having pdc, have some
2159 * issues with the notbusy signal. You can't get it after
2160 * data transmission if you have not sent a stop command.
2161 * The appropriate workaround is to use the BLKE signal.
2162 */
2163 if (pending & ATMCI_BLKE) {
2164 dev_dbg(&host->pdev->dev, "IRQ: blke\n");
2165 atmci_writel(host, ATMCI_IDR, ATMCI_BLKE);
2166 smp_wmb();
2167 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2168 atmci_set_pending(host, EVENT_NOTBUSY);
2169 tasklet_schedule(&host->tasklet);
2170 }
2171
2172 if (pending & ATMCI_NOTBUSY) {
2173 dev_dbg(&host->pdev->dev, "IRQ: not_busy\n");
2174 atmci_writel(host, ATMCI_IDR, ATMCI_NOTBUSY);
2175 smp_wmb();
2176 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2177 atmci_set_pending(host, EVENT_NOTBUSY);
2178 tasklet_schedule(&host->tasklet);
2179 }
2180
2181 if (pending & ATMCI_RXRDY)
2182 atmci_read_data_pio(host);
2183 if (pending & ATMCI_TXRDY)
2184 atmci_write_data_pio(host);
2185
2186 if (pending & ATMCI_CMDRDY) {
2187 dev_dbg(&host->pdev->dev, "IRQ: cmd ready\n");
2188 atmci_writel(host, ATMCI_IDR, ATMCI_CMDRDY);
2189 host->cmd_status = status;
2190 smp_wmb();
2191 dev_dbg(&host->pdev->dev, "set pending cmd rdy\n");
2192 atmci_set_pending(host, EVENT_CMD_RDY);
2193 tasklet_schedule(&host->tasklet);
2194 }
2195
2196 if (pending & (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
2197 atmci_sdio_interrupt(host, status);
2198
2199 } while (pass_count++ < 5);
2200
2201 return pass_count ? IRQ_HANDLED : IRQ_NONE;
2202}
2203
2204static irqreturn_t atmci_detect_interrupt(int irq, void *dev_id)
2205{
2206 struct atmel_mci_slot *slot = dev_id;
2207
2208 /*
2209 * Disable interrupts until the pin has stabilized and check
2210 * the state then. Use mod_timer() since we may be in the
2211 * middle of the timer routine when this interrupt triggers.
2212 */
2213 disable_irq_nosync(irq);
2214 mod_timer(&slot->detect_timer, jiffies + msecs_to_jiffies(20));
2215
2216 return IRQ_HANDLED;
2217}
2218
2219static int atmci_init_slot(struct atmel_mci *host,
2220 struct mci_slot_pdata *slot_data, unsigned int id,
2221 u32 sdc_reg, u32 sdio_irq)
2222{
2223 struct mmc_host *mmc;
2224 struct atmel_mci_slot *slot;
2225 int ret;
2226
2227 mmc = mmc_alloc_host(sizeof(struct atmel_mci_slot), &host->pdev->dev);
2228 if (!mmc)
2229 return -ENOMEM;
2230
2231 slot = mmc_priv(mmc);
2232 slot->mmc = mmc;
2233 slot->host = host;
2234 slot->detect_pin = slot_data->detect_pin;
2235 slot->wp_pin = slot_data->wp_pin;
2236 slot->detect_is_active_high = slot_data->detect_is_active_high;
2237 slot->sdc_reg = sdc_reg;
2238 slot->sdio_irq = sdio_irq;
2239
2240 dev_dbg(&mmc->class_dev,
2241 "slot[%u]: bus_width=%u, detect_pin=%d, "
2242 "detect_is_active_high=%s, wp_pin=%d\n",
2243 id, slot_data->bus_width, slot_data->detect_pin,
2244 slot_data->detect_is_active_high ? "true" : "false",
2245 slot_data->wp_pin);
2246
2247 mmc->ops = &atmci_ops;
2248 mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
2249 mmc->f_max = host->bus_hz / 2;
2250 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2251 if (sdio_irq)
2252 mmc->caps |= MMC_CAP_SDIO_IRQ;
2253 if (host->caps.has_highspeed)
2254 mmc->caps |= MMC_CAP_SD_HIGHSPEED;
2255 /*
2256 * Without the read/write proof capability, it is strongly suggested to
2257 * use only one bit for data to prevent fifo underruns and overruns
2258 * which will corrupt data.
2259 */
2260 if ((slot_data->bus_width >= 4) && host->caps.has_rwproof) {
2261 mmc->caps |= MMC_CAP_4_BIT_DATA;
2262 if (slot_data->bus_width >= 8)
2263 mmc->caps |= MMC_CAP_8_BIT_DATA;
2264 }
2265
2266 if (atmci_get_version(host) < 0x200) {
2267 mmc->max_segs = 256;
2268 mmc->max_blk_size = 4095;
2269 mmc->max_blk_count = 256;
2270 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2271 mmc->max_seg_size = mmc->max_blk_size * mmc->max_segs;
2272 } else {
2273 mmc->max_segs = 64;
2274 mmc->max_req_size = 32768 * 512;
2275 mmc->max_blk_size = 32768;
2276 mmc->max_blk_count = 512;
2277 }
2278
2279 /* Assume card is present initially */
2280 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
2281 if (gpio_is_valid(slot->detect_pin)) {
2282 if (devm_gpio_request(&host->pdev->dev, slot->detect_pin,
2283 "mmc_detect")) {
2284 dev_dbg(&mmc->class_dev, "no detect pin available\n");
2285 slot->detect_pin = -EBUSY;
2286 } else if (gpio_get_value(slot->detect_pin) ^
2287 slot->detect_is_active_high) {
2288 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
2289 }
2290 }
2291
2292 if (!gpio_is_valid(slot->detect_pin)) {
2293 if (slot_data->non_removable)
2294 mmc->caps |= MMC_CAP_NONREMOVABLE;
2295 else
2296 mmc->caps |= MMC_CAP_NEEDS_POLL;
2297 }
2298
2299 if (gpio_is_valid(slot->wp_pin)) {
2300 if (devm_gpio_request(&host->pdev->dev, slot->wp_pin,
2301 "mmc_wp")) {
2302 dev_dbg(&mmc->class_dev, "no WP pin available\n");
2303 slot->wp_pin = -EBUSY;
2304 }
2305 }
2306
2307 host->slot[id] = slot;
2308 mmc_regulator_get_supply(mmc);
2309 ret = mmc_add_host(mmc);
2310 if (ret) {
2311 mmc_free_host(mmc);
2312 return ret;
2313 }
2314
2315 if (gpio_is_valid(slot->detect_pin)) {
2316 timer_setup(&slot->detect_timer, atmci_detect_change, 0);
2317
2318 ret = request_irq(gpio_to_irq(slot->detect_pin),
2319 atmci_detect_interrupt,
2320 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
2321 "mmc-detect", slot);
2322 if (ret) {
2323 dev_dbg(&mmc->class_dev,
2324 "could not request IRQ %d for detect pin\n",
2325 gpio_to_irq(slot->detect_pin));
2326 slot->detect_pin = -EBUSY;
2327 }
2328 }
2329
2330 atmci_init_debugfs(slot);
2331
2332 return 0;
2333}
2334
2335static void atmci_cleanup_slot(struct atmel_mci_slot *slot,
2336 unsigned int id)
2337{
2338 /* Debugfs stuff is cleaned up by mmc core */
2339
2340 set_bit(ATMCI_SHUTDOWN, &slot->flags);
2341 smp_wmb();
2342
2343 mmc_remove_host(slot->mmc);
2344
2345 if (gpio_is_valid(slot->detect_pin)) {
2346 int pin = slot->detect_pin;
2347
2348 free_irq(gpio_to_irq(pin), slot);
2349 del_timer_sync(&slot->detect_timer);
2350 }
2351
2352 slot->host->slot[id] = NULL;
2353 mmc_free_host(slot->mmc);
2354}
2355
2356static int atmci_configure_dma(struct atmel_mci *host)
2357{
2358 host->dma.chan = dma_request_chan(&host->pdev->dev, "rxtx");
2359
2360 if (PTR_ERR(host->dma.chan) == -ENODEV) {
2361 struct mci_platform_data *pdata = host->pdev->dev.platform_data;
2362 dma_cap_mask_t mask;
2363
2364 if (!pdata || !pdata->dma_filter)
2365 return -ENODEV;
2366
2367 dma_cap_zero(mask);
2368 dma_cap_set(DMA_SLAVE, mask);
2369
2370 host->dma.chan = dma_request_channel(mask, pdata->dma_filter,
2371 pdata->dma_slave);
2372 if (!host->dma.chan)
2373 host->dma.chan = ERR_PTR(-ENODEV);
2374 }
2375
2376 if (IS_ERR(host->dma.chan))
2377 return PTR_ERR(host->dma.chan);
2378
2379 dev_info(&host->pdev->dev, "using %s for DMA transfers\n",
2380 dma_chan_name(host->dma.chan));
2381
2382 host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
2383 host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2384 host->dma_conf.src_maxburst = 1;
2385 host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
2386 host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2387 host->dma_conf.dst_maxburst = 1;
2388 host->dma_conf.device_fc = false;
2389
2390 return 0;
2391}
2392
2393/*
2394 * HSMCI (High Speed MCI) module is not fully compatible with MCI module.
2395 * HSMCI provides DMA support and a new config register but no more supports
2396 * PDC.
2397 */
2398static void atmci_get_cap(struct atmel_mci *host)
2399{
2400 unsigned int version;
2401
2402 version = atmci_get_version(host);
2403 dev_info(&host->pdev->dev,
2404 "version: 0x%x\n", version);
2405
2406 host->caps.has_dma_conf_reg = false;
2407 host->caps.has_pdc = true;
2408 host->caps.has_cfg_reg = false;
2409 host->caps.has_cstor_reg = false;
2410 host->caps.has_highspeed = false;
2411 host->caps.has_rwproof = false;
2412 host->caps.has_odd_clk_div = false;
2413 host->caps.has_bad_data_ordering = true;
2414 host->caps.need_reset_after_xfer = true;
2415 host->caps.need_blksz_mul_4 = true;
2416 host->caps.need_notbusy_for_read_ops = false;
2417
2418 /* keep only major version number */
2419 switch (version & 0xf00) {
2420 case 0x600:
2421 case 0x500:
2422 host->caps.has_odd_clk_div = true;
2423 fallthrough;
2424 case 0x400:
2425 case 0x300:
2426 host->caps.has_dma_conf_reg = true;
2427 host->caps.has_pdc = false;
2428 host->caps.has_cfg_reg = true;
2429 host->caps.has_cstor_reg = true;
2430 host->caps.has_highspeed = true;
2431 fallthrough;
2432 case 0x200:
2433 host->caps.has_rwproof = true;
2434 host->caps.need_blksz_mul_4 = false;
2435 host->caps.need_notbusy_for_read_ops = true;
2436 fallthrough;
2437 case 0x100:
2438 host->caps.has_bad_data_ordering = false;
2439 host->caps.need_reset_after_xfer = false;
2440 fallthrough;
2441 case 0x0:
2442 break;
2443 default:
2444 host->caps.has_pdc = false;
2445 dev_warn(&host->pdev->dev,
2446 "Unmanaged mci version, set minimum capabilities\n");
2447 break;
2448 }
2449}
2450
2451static int atmci_probe(struct platform_device *pdev)
2452{
2453 struct mci_platform_data *pdata;
2454 struct atmel_mci *host;
2455 struct resource *regs;
2456 unsigned int nr_slots;
2457 int irq;
2458 int ret, i;
2459
2460 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2461 if (!regs)
2462 return -ENXIO;
2463 pdata = pdev->dev.platform_data;
2464 if (!pdata) {
2465 pdata = atmci_of_init(pdev);
2466 if (IS_ERR(pdata)) {
2467 dev_err(&pdev->dev, "platform data not available\n");
2468 return PTR_ERR(pdata);
2469 }
2470 }
2471
2472 irq = platform_get_irq(pdev, 0);
2473 if (irq < 0)
2474 return irq;
2475
2476 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
2477 if (!host)
2478 return -ENOMEM;
2479
2480 host->pdev = pdev;
2481 spin_lock_init(&host->lock);
2482 INIT_LIST_HEAD(&host->queue);
2483
2484 host->mck = devm_clk_get(&pdev->dev, "mci_clk");
2485 if (IS_ERR(host->mck))
2486 return PTR_ERR(host->mck);
2487
2488 host->regs = devm_ioremap(&pdev->dev, regs->start, resource_size(regs));
2489 if (!host->regs)
2490 return -ENOMEM;
2491
2492 ret = clk_prepare_enable(host->mck);
2493 if (ret)
2494 return ret;
2495
2496 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
2497 host->bus_hz = clk_get_rate(host->mck);
2498
2499 host->mapbase = regs->start;
2500
2501 tasklet_setup(&host->tasklet, atmci_tasklet_func);
2502
2503 ret = request_irq(irq, atmci_interrupt, 0, dev_name(&pdev->dev), host);
2504 if (ret) {
2505 clk_disable_unprepare(host->mck);
2506 return ret;
2507 }
2508
2509 /* Get MCI capabilities and set operations according to it */
2510 atmci_get_cap(host);
2511 ret = atmci_configure_dma(host);
2512 if (ret == -EPROBE_DEFER)
2513 goto err_dma_probe_defer;
2514 if (ret == 0) {
2515 host->prepare_data = &atmci_prepare_data_dma;
2516 host->submit_data = &atmci_submit_data_dma;
2517 host->stop_transfer = &atmci_stop_transfer_dma;
2518 } else if (host->caps.has_pdc) {
2519 dev_info(&pdev->dev, "using PDC\n");
2520 host->prepare_data = &atmci_prepare_data_pdc;
2521 host->submit_data = &atmci_submit_data_pdc;
2522 host->stop_transfer = &atmci_stop_transfer_pdc;
2523 } else {
2524 dev_info(&pdev->dev, "using PIO\n");
2525 host->prepare_data = &atmci_prepare_data;
2526 host->submit_data = &atmci_submit_data;
2527 host->stop_transfer = &atmci_stop_transfer;
2528 }
2529
2530 platform_set_drvdata(pdev, host);
2531
2532 timer_setup(&host->timer, atmci_timeout_timer, 0);
2533
2534 pm_runtime_get_noresume(&pdev->dev);
2535 pm_runtime_set_active(&pdev->dev);
2536 pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_DELAY);
2537 pm_runtime_use_autosuspend(&pdev->dev);
2538 pm_runtime_enable(&pdev->dev);
2539
2540 /* We need at least one slot to succeed */
2541 nr_slots = 0;
2542 ret = -ENODEV;
2543 if (pdata->slot[0].bus_width) {
2544 ret = atmci_init_slot(host, &pdata->slot[0],
2545 0, ATMCI_SDCSEL_SLOT_A, ATMCI_SDIOIRQA);
2546 if (!ret) {
2547 nr_slots++;
2548 host->buf_size = host->slot[0]->mmc->max_req_size;
2549 }
2550 }
2551 if (pdata->slot[1].bus_width) {
2552 ret = atmci_init_slot(host, &pdata->slot[1],
2553 1, ATMCI_SDCSEL_SLOT_B, ATMCI_SDIOIRQB);
2554 if (!ret) {
2555 nr_slots++;
2556 if (host->slot[1]->mmc->max_req_size > host->buf_size)
2557 host->buf_size =
2558 host->slot[1]->mmc->max_req_size;
2559 }
2560 }
2561
2562 if (!nr_slots) {
2563 dev_err(&pdev->dev, "init failed: no slot defined\n");
2564 goto err_init_slot;
2565 }
2566
2567 if (!host->caps.has_rwproof) {
2568 host->buffer = dma_alloc_coherent(&pdev->dev, host->buf_size,
2569 &host->buf_phys_addr,
2570 GFP_KERNEL);
2571 if (!host->buffer) {
2572 ret = -ENOMEM;
2573 dev_err(&pdev->dev, "buffer allocation failed\n");
2574 goto err_dma_alloc;
2575 }
2576 }
2577
2578 dev_info(&pdev->dev,
2579 "Atmel MCI controller at 0x%08lx irq %d, %u slots\n",
2580 host->mapbase, irq, nr_slots);
2581
2582 pm_runtime_mark_last_busy(&host->pdev->dev);
2583 pm_runtime_put_autosuspend(&pdev->dev);
2584
2585 return 0;
2586
2587err_dma_alloc:
2588 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2589 if (host->slot[i])
2590 atmci_cleanup_slot(host->slot[i], i);
2591 }
2592err_init_slot:
2593 clk_disable_unprepare(host->mck);
2594
2595 pm_runtime_disable(&pdev->dev);
2596 pm_runtime_put_noidle(&pdev->dev);
2597
2598 del_timer_sync(&host->timer);
2599 if (!IS_ERR(host->dma.chan))
2600 dma_release_channel(host->dma.chan);
2601err_dma_probe_defer:
2602 free_irq(irq, host);
2603 return ret;
2604}
2605
2606static int atmci_remove(struct platform_device *pdev)
2607{
2608 struct atmel_mci *host = platform_get_drvdata(pdev);
2609 unsigned int i;
2610
2611 pm_runtime_get_sync(&pdev->dev);
2612
2613 if (host->buffer)
2614 dma_free_coherent(&pdev->dev, host->buf_size,
2615 host->buffer, host->buf_phys_addr);
2616
2617 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2618 if (host->slot[i])
2619 atmci_cleanup_slot(host->slot[i], i);
2620 }
2621
2622 atmci_writel(host, ATMCI_IDR, ~0UL);
2623 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
2624 atmci_readl(host, ATMCI_SR);
2625
2626 del_timer_sync(&host->timer);
2627 if (!IS_ERR(host->dma.chan))
2628 dma_release_channel(host->dma.chan);
2629
2630 free_irq(platform_get_irq(pdev, 0), host);
2631
2632 clk_disable_unprepare(host->mck);
2633
2634 pm_runtime_disable(&pdev->dev);
2635 pm_runtime_put_noidle(&pdev->dev);
2636
2637 return 0;
2638}
2639
2640#ifdef CONFIG_PM
2641static int atmci_runtime_suspend(struct device *dev)
2642{
2643 struct atmel_mci *host = dev_get_drvdata(dev);
2644
2645 clk_disable_unprepare(host->mck);
2646
2647 pinctrl_pm_select_sleep_state(dev);
2648
2649 return 0;
2650}
2651
2652static int atmci_runtime_resume(struct device *dev)
2653{
2654 struct atmel_mci *host = dev_get_drvdata(dev);
2655
2656 pinctrl_select_default_state(dev);
2657
2658 return clk_prepare_enable(host->mck);
2659}
2660#endif
2661
2662static const struct dev_pm_ops atmci_dev_pm_ops = {
2663 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
2664 pm_runtime_force_resume)
2665 SET_RUNTIME_PM_OPS(atmci_runtime_suspend, atmci_runtime_resume, NULL)
2666};
2667
2668static struct platform_driver atmci_driver = {
2669 .probe = atmci_probe,
2670 .remove = atmci_remove,
2671 .driver = {
2672 .name = "atmel_mci",
2673 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
2674 .of_match_table = of_match_ptr(atmci_dt_ids),
2675 .pm = &atmci_dev_pm_ops,
2676 },
2677};
2678module_platform_driver(atmci_driver);
2679
2680MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver");
2681MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
2682MODULE_LICENSE("GPL v2");
1/*
2 * Atmel MultiMedia Card Interface driver
3 *
4 * Copyright (C) 2004-2008 Atmel Corporation
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License version 2 as
8 * published by the Free Software Foundation.
9 */
10#include <linux/blkdev.h>
11#include <linux/clk.h>
12#include <linux/debugfs.h>
13#include <linux/device.h>
14#include <linux/dmaengine.h>
15#include <linux/dma-mapping.h>
16#include <linux/err.h>
17#include <linux/gpio.h>
18#include <linux/init.h>
19#include <linux/interrupt.h>
20#include <linux/io.h>
21#include <linux/ioport.h>
22#include <linux/module.h>
23#include <linux/of.h>
24#include <linux/of_device.h>
25#include <linux/of_gpio.h>
26#include <linux/platform_device.h>
27#include <linux/scatterlist.h>
28#include <linux/seq_file.h>
29#include <linux/slab.h>
30#include <linux/stat.h>
31#include <linux/types.h>
32
33#include <linux/mmc/host.h>
34#include <linux/mmc/sdio.h>
35
36#include <linux/atmel-mci.h>
37#include <linux/atmel_pdc.h>
38#include <linux/pm.h>
39#include <linux/pm_runtime.h>
40#include <linux/pinctrl/consumer.h>
41
42#include <asm/cacheflush.h>
43#include <asm/io.h>
44#include <asm/unaligned.h>
45
46/*
47 * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
48 * Registers and bitfields marked with [2] are only available in MCI2
49 */
50
51/* MCI Register Definitions */
52#define ATMCI_CR 0x0000 /* Control */
53#define ATMCI_CR_MCIEN BIT(0) /* MCI Enable */
54#define ATMCI_CR_MCIDIS BIT(1) /* MCI Disable */
55#define ATMCI_CR_PWSEN BIT(2) /* Power Save Enable */
56#define ATMCI_CR_PWSDIS BIT(3) /* Power Save Disable */
57#define ATMCI_CR_SWRST BIT(7) /* Software Reset */
58#define ATMCI_MR 0x0004 /* Mode */
59#define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
60#define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
61#define ATMCI_MR_RDPROOF BIT(11) /* Read Proof */
62#define ATMCI_MR_WRPROOF BIT(12) /* Write Proof */
63#define ATMCI_MR_PDCFBYTE BIT(13) /* Force Byte Transfer */
64#define ATMCI_MR_PDCPADV BIT(14) /* Padding Value */
65#define ATMCI_MR_PDCMODE BIT(15) /* PDC-oriented Mode */
66#define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
67#define ATMCI_DTOR 0x0008 /* Data Timeout */
68#define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
69#define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
70#define ATMCI_SDCR 0x000c /* SD Card / SDIO */
71#define ATMCI_SDCSEL_SLOT_A (0 << 0) /* Select SD slot A */
72#define ATMCI_SDCSEL_SLOT_B (1 << 0) /* Select SD slot A */
73#define ATMCI_SDCSEL_MASK (3 << 0)
74#define ATMCI_SDCBUS_1BIT (0 << 6) /* 1-bit data bus */
75#define ATMCI_SDCBUS_4BIT (2 << 6) /* 4-bit data bus */
76#define ATMCI_SDCBUS_8BIT (3 << 6) /* 8-bit data bus[2] */
77#define ATMCI_SDCBUS_MASK (3 << 6)
78#define ATMCI_ARGR 0x0010 /* Command Argument */
79#define ATMCI_CMDR 0x0014 /* Command */
80#define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
81#define ATMCI_CMDR_RSPTYP_NONE (0 << 6) /* No response */
82#define ATMCI_CMDR_RSPTYP_48BIT (1 << 6) /* 48-bit response */
83#define ATMCI_CMDR_RSPTYP_136BIT (2 << 6) /* 136-bit response */
84#define ATMCI_CMDR_SPCMD_INIT (1 << 8) /* Initialization command */
85#define ATMCI_CMDR_SPCMD_SYNC (2 << 8) /* Synchronized command */
86#define ATMCI_CMDR_SPCMD_INT (4 << 8) /* Interrupt command */
87#define ATMCI_CMDR_SPCMD_INTRESP (5 << 8) /* Interrupt response */
88#define ATMCI_CMDR_OPDCMD (1 << 11) /* Open Drain */
89#define ATMCI_CMDR_MAXLAT_5CYC (0 << 12) /* Max latency 5 cycles */
90#define ATMCI_CMDR_MAXLAT_64CYC (1 << 12) /* Max latency 64 cycles */
91#define ATMCI_CMDR_START_XFER (1 << 16) /* Start data transfer */
92#define ATMCI_CMDR_STOP_XFER (2 << 16) /* Stop data transfer */
93#define ATMCI_CMDR_TRDIR_WRITE (0 << 18) /* Write data */
94#define ATMCI_CMDR_TRDIR_READ (1 << 18) /* Read data */
95#define ATMCI_CMDR_BLOCK (0 << 19) /* Single-block transfer */
96#define ATMCI_CMDR_MULTI_BLOCK (1 << 19) /* Multi-block transfer */
97#define ATMCI_CMDR_STREAM (2 << 19) /* MMC Stream transfer */
98#define ATMCI_CMDR_SDIO_BYTE (4 << 19) /* SDIO Byte transfer */
99#define ATMCI_CMDR_SDIO_BLOCK (5 << 19) /* SDIO Block transfer */
100#define ATMCI_CMDR_SDIO_SUSPEND (1 << 24) /* SDIO Suspend Command */
101#define ATMCI_CMDR_SDIO_RESUME (2 << 24) /* SDIO Resume Command */
102#define ATMCI_BLKR 0x0018 /* Block */
103#define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
104#define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
105#define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
106#define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
107#define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
108#define ATMCI_RSPR 0x0020 /* Response 0 */
109#define ATMCI_RSPR1 0x0024 /* Response 1 */
110#define ATMCI_RSPR2 0x0028 /* Response 2 */
111#define ATMCI_RSPR3 0x002c /* Response 3 */
112#define ATMCI_RDR 0x0030 /* Receive Data */
113#define ATMCI_TDR 0x0034 /* Transmit Data */
114#define ATMCI_SR 0x0040 /* Status */
115#define ATMCI_IER 0x0044 /* Interrupt Enable */
116#define ATMCI_IDR 0x0048 /* Interrupt Disable */
117#define ATMCI_IMR 0x004c /* Interrupt Mask */
118#define ATMCI_CMDRDY BIT(0) /* Command Ready */
119#define ATMCI_RXRDY BIT(1) /* Receiver Ready */
120#define ATMCI_TXRDY BIT(2) /* Transmitter Ready */
121#define ATMCI_BLKE BIT(3) /* Data Block Ended */
122#define ATMCI_DTIP BIT(4) /* Data Transfer In Progress */
123#define ATMCI_NOTBUSY BIT(5) /* Data Not Busy */
124#define ATMCI_ENDRX BIT(6) /* End of RX Buffer */
125#define ATMCI_ENDTX BIT(7) /* End of TX Buffer */
126#define ATMCI_SDIOIRQA BIT(8) /* SDIO IRQ in slot A */
127#define ATMCI_SDIOIRQB BIT(9) /* SDIO IRQ in slot B */
128#define ATMCI_SDIOWAIT BIT(12) /* SDIO Read Wait Operation Status */
129#define ATMCI_CSRCV BIT(13) /* CE-ATA Completion Signal Received */
130#define ATMCI_RXBUFF BIT(14) /* RX Buffer Full */
131#define ATMCI_TXBUFE BIT(15) /* TX Buffer Empty */
132#define ATMCI_RINDE BIT(16) /* Response Index Error */
133#define ATMCI_RDIRE BIT(17) /* Response Direction Error */
134#define ATMCI_RCRCE BIT(18) /* Response CRC Error */
135#define ATMCI_RENDE BIT(19) /* Response End Bit Error */
136#define ATMCI_RTOE BIT(20) /* Response Time-Out Error */
137#define ATMCI_DCRCE BIT(21) /* Data CRC Error */
138#define ATMCI_DTOE BIT(22) /* Data Time-Out Error */
139#define ATMCI_CSTOE BIT(23) /* Completion Signal Time-out Error */
140#define ATMCI_BLKOVRE BIT(24) /* DMA Block Overrun Error */
141#define ATMCI_DMADONE BIT(25) /* DMA Transfer Done */
142#define ATMCI_FIFOEMPTY BIT(26) /* FIFO Empty Flag */
143#define ATMCI_XFRDONE BIT(27) /* Transfer Done Flag */
144#define ATMCI_ACKRCV BIT(28) /* Boot Operation Acknowledge Received */
145#define ATMCI_ACKRCVE BIT(29) /* Boot Operation Acknowledge Error */
146#define ATMCI_OVRE BIT(30) /* RX Overrun Error */
147#define ATMCI_UNRE BIT(31) /* TX Underrun Error */
148#define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
149#define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
150#define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
151#define ATMCI_DMAEN BIT(8) /* DMA Hardware Handshaking Enable */
152#define ATMCI_CFG 0x0054 /* Configuration[2] */
153#define ATMCI_CFG_FIFOMODE_1DATA BIT(0) /* MCI Internal FIFO control mode */
154#define ATMCI_CFG_FERRCTRL_COR BIT(4) /* Flow Error flag reset control mode */
155#define ATMCI_CFG_HSMODE BIT(8) /* High Speed Mode */
156#define ATMCI_CFG_LSYNC BIT(12) /* Synchronize on the last block */
157#define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
158#define ATMCI_WP_EN BIT(0) /* WP Enable */
159#define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
160#define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
161#define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
162#define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
163#define ATMCI_VERSION 0x00FC /* Version */
164#define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
165
166/* This is not including the FIFO Aperture on MCI2 */
167#define ATMCI_REGS_SIZE 0x100
168
169/* Register access macros */
170#define atmci_readl(port, reg) \
171 __raw_readl((port)->regs + reg)
172#define atmci_writel(port, reg, value) \
173 __raw_writel((value), (port)->regs + reg)
174
175/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */
176#ifdef CONFIG_AVR32
177# define ATMCI_PDC_CONNECTED 0
178#else
179# define ATMCI_PDC_CONNECTED 1
180#endif
181
182#define AUTOSUSPEND_DELAY 50
183
184#define ATMCI_DATA_ERROR_FLAGS (ATMCI_DCRCE | ATMCI_DTOE | ATMCI_OVRE | ATMCI_UNRE)
185#define ATMCI_DMA_THRESHOLD 16
186
187enum {
188 EVENT_CMD_RDY = 0,
189 EVENT_XFER_COMPLETE,
190 EVENT_NOTBUSY,
191 EVENT_DATA_ERROR,
192};
193
194enum atmel_mci_state {
195 STATE_IDLE = 0,
196 STATE_SENDING_CMD,
197 STATE_DATA_XFER,
198 STATE_WAITING_NOTBUSY,
199 STATE_SENDING_STOP,
200 STATE_END_REQUEST,
201};
202
203enum atmci_xfer_dir {
204 XFER_RECEIVE = 0,
205 XFER_TRANSMIT,
206};
207
208enum atmci_pdc_buf {
209 PDC_FIRST_BUF = 0,
210 PDC_SECOND_BUF,
211};
212
213struct atmel_mci_caps {
214 bool has_dma_conf_reg;
215 bool has_pdc;
216 bool has_cfg_reg;
217 bool has_cstor_reg;
218 bool has_highspeed;
219 bool has_rwproof;
220 bool has_odd_clk_div;
221 bool has_bad_data_ordering;
222 bool need_reset_after_xfer;
223 bool need_blksz_mul_4;
224 bool need_notbusy_for_read_ops;
225};
226
227struct atmel_mci_dma {
228 struct dma_chan *chan;
229 struct dma_async_tx_descriptor *data_desc;
230};
231
232/**
233 * struct atmel_mci - MMC controller state shared between all slots
234 * @lock: Spinlock protecting the queue and associated data.
235 * @regs: Pointer to MMIO registers.
236 * @sg: Scatterlist entry currently being processed by PIO or PDC code.
237 * @pio_offset: Offset into the current scatterlist entry.
238 * @buffer: Buffer used if we don't have the r/w proof capability. We
239 * don't have the time to switch pdc buffers so we have to use only
240 * one buffer for the full transaction.
241 * @buf_size: size of the buffer.
242 * @phys_buf_addr: buffer address needed for pdc.
243 * @cur_slot: The slot which is currently using the controller.
244 * @mrq: The request currently being processed on @cur_slot,
245 * or NULL if the controller is idle.
246 * @cmd: The command currently being sent to the card, or NULL.
247 * @data: The data currently being transferred, or NULL if no data
248 * transfer is in progress.
249 * @data_size: just data->blocks * data->blksz.
250 * @dma: DMA client state.
251 * @data_chan: DMA channel being used for the current data transfer.
252 * @cmd_status: Snapshot of SR taken upon completion of the current
253 * command. Only valid when EVENT_CMD_COMPLETE is pending.
254 * @data_status: Snapshot of SR taken upon completion of the current
255 * data transfer. Only valid when EVENT_DATA_COMPLETE or
256 * EVENT_DATA_ERROR is pending.
257 * @stop_cmdr: Value to be loaded into CMDR when the stop command is
258 * to be sent.
259 * @tasklet: Tasklet running the request state machine.
260 * @pending_events: Bitmask of events flagged by the interrupt handler
261 * to be processed by the tasklet.
262 * @completed_events: Bitmask of events which the state machine has
263 * processed.
264 * @state: Tasklet state.
265 * @queue: List of slots waiting for access to the controller.
266 * @need_clock_update: Update the clock rate before the next request.
267 * @need_reset: Reset controller before next request.
268 * @timer: Timer to balance the data timeout error flag which cannot rise.
269 * @mode_reg: Value of the MR register.
270 * @cfg_reg: Value of the CFG register.
271 * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
272 * rate and timeout calculations.
273 * @mapbase: Physical address of the MMIO registers.
274 * @mck: The peripheral bus clock hooked up to the MMC controller.
275 * @pdev: Platform device associated with the MMC controller.
276 * @slot: Slots sharing this MMC controller.
277 * @caps: MCI capabilities depending on MCI version.
278 * @prepare_data: function to setup MCI before data transfer which
279 * depends on MCI capabilities.
280 * @submit_data: function to start data transfer which depends on MCI
281 * capabilities.
282 * @stop_transfer: function to stop data transfer which depends on MCI
283 * capabilities.
284 *
285 * Locking
286 * =======
287 *
288 * @lock is a softirq-safe spinlock protecting @queue as well as
289 * @cur_slot, @mrq and @state. These must always be updated
290 * at the same time while holding @lock.
291 *
292 * @lock also protects mode_reg and need_clock_update since these are
293 * used to synchronize mode register updates with the queue
294 * processing.
295 *
296 * The @mrq field of struct atmel_mci_slot is also protected by @lock,
297 * and must always be written at the same time as the slot is added to
298 * @queue.
299 *
300 * @pending_events and @completed_events are accessed using atomic bit
301 * operations, so they don't need any locking.
302 *
303 * None of the fields touched by the interrupt handler need any
304 * locking. However, ordering is important: Before EVENT_DATA_ERROR or
305 * EVENT_DATA_COMPLETE is set in @pending_events, all data-related
306 * interrupts must be disabled and @data_status updated with a
307 * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the
308 * CMDRDY interrupt must be disabled and @cmd_status updated with a
309 * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the
310 * bytes_xfered field of @data must be written. This is ensured by
311 * using barriers.
312 */
313struct atmel_mci {
314 spinlock_t lock;
315 void __iomem *regs;
316
317 struct scatterlist *sg;
318 unsigned int sg_len;
319 unsigned int pio_offset;
320 unsigned int *buffer;
321 unsigned int buf_size;
322 dma_addr_t buf_phys_addr;
323
324 struct atmel_mci_slot *cur_slot;
325 struct mmc_request *mrq;
326 struct mmc_command *cmd;
327 struct mmc_data *data;
328 unsigned int data_size;
329
330 struct atmel_mci_dma dma;
331 struct dma_chan *data_chan;
332 struct dma_slave_config dma_conf;
333
334 u32 cmd_status;
335 u32 data_status;
336 u32 stop_cmdr;
337
338 struct tasklet_struct tasklet;
339 unsigned long pending_events;
340 unsigned long completed_events;
341 enum atmel_mci_state state;
342 struct list_head queue;
343
344 bool need_clock_update;
345 bool need_reset;
346 struct timer_list timer;
347 u32 mode_reg;
348 u32 cfg_reg;
349 unsigned long bus_hz;
350 unsigned long mapbase;
351 struct clk *mck;
352 struct platform_device *pdev;
353
354 struct atmel_mci_slot *slot[ATMCI_MAX_NR_SLOTS];
355
356 struct atmel_mci_caps caps;
357
358 u32 (*prepare_data)(struct atmel_mci *host, struct mmc_data *data);
359 void (*submit_data)(struct atmel_mci *host, struct mmc_data *data);
360 void (*stop_transfer)(struct atmel_mci *host);
361};
362
363/**
364 * struct atmel_mci_slot - MMC slot state
365 * @mmc: The mmc_host representing this slot.
366 * @host: The MMC controller this slot is using.
367 * @sdc_reg: Value of SDCR to be written before using this slot.
368 * @sdio_irq: SDIO irq mask for this slot.
369 * @mrq: mmc_request currently being processed or waiting to be
370 * processed, or NULL when the slot is idle.
371 * @queue_node: List node for placing this node in the @queue list of
372 * &struct atmel_mci.
373 * @clock: Clock rate configured by set_ios(). Protected by host->lock.
374 * @flags: Random state bits associated with the slot.
375 * @detect_pin: GPIO pin used for card detection, or negative if not
376 * available.
377 * @wp_pin: GPIO pin used for card write protect sending, or negative
378 * if not available.
379 * @detect_is_active_high: The state of the detect pin when it is active.
380 * @detect_timer: Timer used for debouncing @detect_pin interrupts.
381 */
382struct atmel_mci_slot {
383 struct mmc_host *mmc;
384 struct atmel_mci *host;
385
386 u32 sdc_reg;
387 u32 sdio_irq;
388
389 struct mmc_request *mrq;
390 struct list_head queue_node;
391
392 unsigned int clock;
393 unsigned long flags;
394#define ATMCI_CARD_PRESENT 0
395#define ATMCI_CARD_NEED_INIT 1
396#define ATMCI_SHUTDOWN 2
397
398 int detect_pin;
399 int wp_pin;
400 bool detect_is_active_high;
401
402 struct timer_list detect_timer;
403};
404
405#define atmci_test_and_clear_pending(host, event) \
406 test_and_clear_bit(event, &host->pending_events)
407#define atmci_set_completed(host, event) \
408 set_bit(event, &host->completed_events)
409#define atmci_set_pending(host, event) \
410 set_bit(event, &host->pending_events)
411
412/*
413 * The debugfs stuff below is mostly optimized away when
414 * CONFIG_DEBUG_FS is not set.
415 */
416static int atmci_req_show(struct seq_file *s, void *v)
417{
418 struct atmel_mci_slot *slot = s->private;
419 struct mmc_request *mrq;
420 struct mmc_command *cmd;
421 struct mmc_command *stop;
422 struct mmc_data *data;
423
424 /* Make sure we get a consistent snapshot */
425 spin_lock_bh(&slot->host->lock);
426 mrq = slot->mrq;
427
428 if (mrq) {
429 cmd = mrq->cmd;
430 data = mrq->data;
431 stop = mrq->stop;
432
433 if (cmd)
434 seq_printf(s,
435 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
436 cmd->opcode, cmd->arg, cmd->flags,
437 cmd->resp[0], cmd->resp[1], cmd->resp[2],
438 cmd->resp[3], cmd->error);
439 if (data)
440 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
441 data->bytes_xfered, data->blocks,
442 data->blksz, data->flags, data->error);
443 if (stop)
444 seq_printf(s,
445 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
446 stop->opcode, stop->arg, stop->flags,
447 stop->resp[0], stop->resp[1], stop->resp[2],
448 stop->resp[3], stop->error);
449 }
450
451 spin_unlock_bh(&slot->host->lock);
452
453 return 0;
454}
455
456static int atmci_req_open(struct inode *inode, struct file *file)
457{
458 return single_open(file, atmci_req_show, inode->i_private);
459}
460
461static const struct file_operations atmci_req_fops = {
462 .owner = THIS_MODULE,
463 .open = atmci_req_open,
464 .read = seq_read,
465 .llseek = seq_lseek,
466 .release = single_release,
467};
468
469static void atmci_show_status_reg(struct seq_file *s,
470 const char *regname, u32 value)
471{
472 static const char *sr_bit[] = {
473 [0] = "CMDRDY",
474 [1] = "RXRDY",
475 [2] = "TXRDY",
476 [3] = "BLKE",
477 [4] = "DTIP",
478 [5] = "NOTBUSY",
479 [6] = "ENDRX",
480 [7] = "ENDTX",
481 [8] = "SDIOIRQA",
482 [9] = "SDIOIRQB",
483 [12] = "SDIOWAIT",
484 [14] = "RXBUFF",
485 [15] = "TXBUFE",
486 [16] = "RINDE",
487 [17] = "RDIRE",
488 [18] = "RCRCE",
489 [19] = "RENDE",
490 [20] = "RTOE",
491 [21] = "DCRCE",
492 [22] = "DTOE",
493 [23] = "CSTOE",
494 [24] = "BLKOVRE",
495 [25] = "DMADONE",
496 [26] = "FIFOEMPTY",
497 [27] = "XFRDONE",
498 [30] = "OVRE",
499 [31] = "UNRE",
500 };
501 unsigned int i;
502
503 seq_printf(s, "%s:\t0x%08x", regname, value);
504 for (i = 0; i < ARRAY_SIZE(sr_bit); i++) {
505 if (value & (1 << i)) {
506 if (sr_bit[i])
507 seq_printf(s, " %s", sr_bit[i]);
508 else
509 seq_puts(s, " UNKNOWN");
510 }
511 }
512 seq_putc(s, '\n');
513}
514
515static int atmci_regs_show(struct seq_file *s, void *v)
516{
517 struct atmel_mci *host = s->private;
518 u32 *buf;
519 int ret = 0;
520
521
522 buf = kmalloc(ATMCI_REGS_SIZE, GFP_KERNEL);
523 if (!buf)
524 return -ENOMEM;
525
526 pm_runtime_get_sync(&host->pdev->dev);
527
528 /*
529 * Grab a more or less consistent snapshot. Note that we're
530 * not disabling interrupts, so IMR and SR may not be
531 * consistent.
532 */
533 spin_lock_bh(&host->lock);
534 memcpy_fromio(buf, host->regs, ATMCI_REGS_SIZE);
535 spin_unlock_bh(&host->lock);
536
537 pm_runtime_mark_last_busy(&host->pdev->dev);
538 pm_runtime_put_autosuspend(&host->pdev->dev);
539
540 seq_printf(s, "MR:\t0x%08x%s%s ",
541 buf[ATMCI_MR / 4],
542 buf[ATMCI_MR / 4] & ATMCI_MR_RDPROOF ? " RDPROOF" : "",
543 buf[ATMCI_MR / 4] & ATMCI_MR_WRPROOF ? " WRPROOF" : "");
544 if (host->caps.has_odd_clk_div)
545 seq_printf(s, "{CLKDIV,CLKODD}=%u\n",
546 ((buf[ATMCI_MR / 4] & 0xff) << 1)
547 | ((buf[ATMCI_MR / 4] >> 16) & 1));
548 else
549 seq_printf(s, "CLKDIV=%u\n",
550 (buf[ATMCI_MR / 4] & 0xff));
551 seq_printf(s, "DTOR:\t0x%08x\n", buf[ATMCI_DTOR / 4]);
552 seq_printf(s, "SDCR:\t0x%08x\n", buf[ATMCI_SDCR / 4]);
553 seq_printf(s, "ARGR:\t0x%08x\n", buf[ATMCI_ARGR / 4]);
554 seq_printf(s, "BLKR:\t0x%08x BCNT=%u BLKLEN=%u\n",
555 buf[ATMCI_BLKR / 4],
556 buf[ATMCI_BLKR / 4] & 0xffff,
557 (buf[ATMCI_BLKR / 4] >> 16) & 0xffff);
558 if (host->caps.has_cstor_reg)
559 seq_printf(s, "CSTOR:\t0x%08x\n", buf[ATMCI_CSTOR / 4]);
560
561 /* Don't read RSPR and RDR; it will consume the data there */
562
563 atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]);
564 atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]);
565
566 if (host->caps.has_dma_conf_reg) {
567 u32 val;
568
569 val = buf[ATMCI_DMA / 4];
570 seq_printf(s, "DMA:\t0x%08x OFFSET=%u CHKSIZE=%u%s\n",
571 val, val & 3,
572 ((val >> 4) & 3) ?
573 1 << (((val >> 4) & 3) + 1) : 1,
574 val & ATMCI_DMAEN ? " DMAEN" : "");
575 }
576 if (host->caps.has_cfg_reg) {
577 u32 val;
578
579 val = buf[ATMCI_CFG / 4];
580 seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n",
581 val,
582 val & ATMCI_CFG_FIFOMODE_1DATA ? " FIFOMODE_ONE_DATA" : "",
583 val & ATMCI_CFG_FERRCTRL_COR ? " FERRCTRL_CLEAR_ON_READ" : "",
584 val & ATMCI_CFG_HSMODE ? " HSMODE" : "",
585 val & ATMCI_CFG_LSYNC ? " LSYNC" : "");
586 }
587
588 kfree(buf);
589
590 return ret;
591}
592
593static int atmci_regs_open(struct inode *inode, struct file *file)
594{
595 return single_open(file, atmci_regs_show, inode->i_private);
596}
597
598static const struct file_operations atmci_regs_fops = {
599 .owner = THIS_MODULE,
600 .open = atmci_regs_open,
601 .read = seq_read,
602 .llseek = seq_lseek,
603 .release = single_release,
604};
605
606static void atmci_init_debugfs(struct atmel_mci_slot *slot)
607{
608 struct mmc_host *mmc = slot->mmc;
609 struct atmel_mci *host = slot->host;
610 struct dentry *root;
611 struct dentry *node;
612
613 root = mmc->debugfs_root;
614 if (!root)
615 return;
616
617 node = debugfs_create_file("regs", S_IRUSR, root, host,
618 &atmci_regs_fops);
619 if (IS_ERR(node))
620 return;
621 if (!node)
622 goto err;
623
624 node = debugfs_create_file("req", S_IRUSR, root, slot, &atmci_req_fops);
625 if (!node)
626 goto err;
627
628 node = debugfs_create_u32("state", S_IRUSR, root, (u32 *)&host->state);
629 if (!node)
630 goto err;
631
632 node = debugfs_create_x32("pending_events", S_IRUSR, root,
633 (u32 *)&host->pending_events);
634 if (!node)
635 goto err;
636
637 node = debugfs_create_x32("completed_events", S_IRUSR, root,
638 (u32 *)&host->completed_events);
639 if (!node)
640 goto err;
641
642 return;
643
644err:
645 dev_err(&mmc->class_dev, "failed to initialize debugfs for slot\n");
646}
647
648#if defined(CONFIG_OF)
649static const struct of_device_id atmci_dt_ids[] = {
650 { .compatible = "atmel,hsmci" },
651 { /* sentinel */ }
652};
653
654MODULE_DEVICE_TABLE(of, atmci_dt_ids);
655
656static struct mci_platform_data*
657atmci_of_init(struct platform_device *pdev)
658{
659 struct device_node *np = pdev->dev.of_node;
660 struct device_node *cnp;
661 struct mci_platform_data *pdata;
662 u32 slot_id;
663
664 if (!np) {
665 dev_err(&pdev->dev, "device node not found\n");
666 return ERR_PTR(-EINVAL);
667 }
668
669 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
670 if (!pdata) {
671 dev_err(&pdev->dev, "could not allocate memory for pdata\n");
672 return ERR_PTR(-ENOMEM);
673 }
674
675 for_each_child_of_node(np, cnp) {
676 if (of_property_read_u32(cnp, "reg", &slot_id)) {
677 dev_warn(&pdev->dev, "reg property is missing for %s\n",
678 cnp->full_name);
679 continue;
680 }
681
682 if (slot_id >= ATMCI_MAX_NR_SLOTS) {
683 dev_warn(&pdev->dev, "can't have more than %d slots\n",
684 ATMCI_MAX_NR_SLOTS);
685 break;
686 }
687
688 if (of_property_read_u32(cnp, "bus-width",
689 &pdata->slot[slot_id].bus_width))
690 pdata->slot[slot_id].bus_width = 1;
691
692 pdata->slot[slot_id].detect_pin =
693 of_get_named_gpio(cnp, "cd-gpios", 0);
694
695 pdata->slot[slot_id].detect_is_active_high =
696 of_property_read_bool(cnp, "cd-inverted");
697
698 pdata->slot[slot_id].non_removable =
699 of_property_read_bool(cnp, "non-removable");
700
701 pdata->slot[slot_id].wp_pin =
702 of_get_named_gpio(cnp, "wp-gpios", 0);
703 }
704
705 return pdata;
706}
707#else /* CONFIG_OF */
708static inline struct mci_platform_data*
709atmci_of_init(struct platform_device *dev)
710{
711 return ERR_PTR(-EINVAL);
712}
713#endif
714
715static inline unsigned int atmci_get_version(struct atmel_mci *host)
716{
717 return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
718}
719
720/*
721 * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
722 * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
723 * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
724 * 8 -> 3, 16 -> 4.
725 *
726 * This can be done by finding most significant bit set.
727 */
728static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
729 unsigned int maxburst)
730{
731 unsigned int version = atmci_get_version(host);
732 unsigned int offset = 2;
733
734 if (version >= 0x600)
735 offset = 1;
736
737 if (maxburst > 1)
738 return fls(maxburst) - offset;
739 else
740 return 0;
741}
742
743static void atmci_timeout_timer(unsigned long data)
744{
745 struct atmel_mci *host;
746
747 host = (struct atmel_mci *)data;
748
749 dev_dbg(&host->pdev->dev, "software timeout\n");
750
751 if (host->mrq->cmd->data) {
752 host->mrq->cmd->data->error = -ETIMEDOUT;
753 host->data = NULL;
754 /*
755 * With some SDIO modules, sometimes DMA transfer hangs. If
756 * stop_transfer() is not called then the DMA request is not
757 * removed, following ones are queued and never computed.
758 */
759 if (host->state == STATE_DATA_XFER)
760 host->stop_transfer(host);
761 } else {
762 host->mrq->cmd->error = -ETIMEDOUT;
763 host->cmd = NULL;
764 }
765 host->need_reset = 1;
766 host->state = STATE_END_REQUEST;
767 smp_wmb();
768 tasklet_schedule(&host->tasklet);
769}
770
771static inline unsigned int atmci_ns_to_clocks(struct atmel_mci *host,
772 unsigned int ns)
773{
774 /*
775 * It is easier here to use us instead of ns for the timeout,
776 * it prevents from overflows during calculation.
777 */
778 unsigned int us = DIV_ROUND_UP(ns, 1000);
779
780 /* Maximum clock frequency is host->bus_hz/2 */
781 return us * (DIV_ROUND_UP(host->bus_hz, 2000000));
782}
783
784static void atmci_set_timeout(struct atmel_mci *host,
785 struct atmel_mci_slot *slot, struct mmc_data *data)
786{
787 static unsigned dtomul_to_shift[] = {
788 0, 4, 7, 8, 10, 12, 16, 20
789 };
790 unsigned timeout;
791 unsigned dtocyc;
792 unsigned dtomul;
793
794 timeout = atmci_ns_to_clocks(host, data->timeout_ns)
795 + data->timeout_clks;
796
797 for (dtomul = 0; dtomul < 8; dtomul++) {
798 unsigned shift = dtomul_to_shift[dtomul];
799 dtocyc = (timeout + (1 << shift) - 1) >> shift;
800 if (dtocyc < 15)
801 break;
802 }
803
804 if (dtomul >= 8) {
805 dtomul = 7;
806 dtocyc = 15;
807 }
808
809 dev_vdbg(&slot->mmc->class_dev, "setting timeout to %u cycles\n",
810 dtocyc << dtomul_to_shift[dtomul]);
811 atmci_writel(host, ATMCI_DTOR, (ATMCI_DTOMUL(dtomul) | ATMCI_DTOCYC(dtocyc)));
812}
813
814/*
815 * Return mask with command flags to be enabled for this command.
816 */
817static u32 atmci_prepare_command(struct mmc_host *mmc,
818 struct mmc_command *cmd)
819{
820 struct mmc_data *data;
821 u32 cmdr;
822
823 cmd->error = -EINPROGRESS;
824
825 cmdr = ATMCI_CMDR_CMDNB(cmd->opcode);
826
827 if (cmd->flags & MMC_RSP_PRESENT) {
828 if (cmd->flags & MMC_RSP_136)
829 cmdr |= ATMCI_CMDR_RSPTYP_136BIT;
830 else
831 cmdr |= ATMCI_CMDR_RSPTYP_48BIT;
832 }
833
834 /*
835 * This should really be MAXLAT_5 for CMD2 and ACMD41, but
836 * it's too difficult to determine whether this is an ACMD or
837 * not. Better make it 64.
838 */
839 cmdr |= ATMCI_CMDR_MAXLAT_64CYC;
840
841 if (mmc->ios.bus_mode == MMC_BUSMODE_OPENDRAIN)
842 cmdr |= ATMCI_CMDR_OPDCMD;
843
844 data = cmd->data;
845 if (data) {
846 cmdr |= ATMCI_CMDR_START_XFER;
847
848 if (cmd->opcode == SD_IO_RW_EXTENDED) {
849 cmdr |= ATMCI_CMDR_SDIO_BLOCK;
850 } else {
851 if (data->blocks > 1)
852 cmdr |= ATMCI_CMDR_MULTI_BLOCK;
853 else
854 cmdr |= ATMCI_CMDR_BLOCK;
855 }
856
857 if (data->flags & MMC_DATA_READ)
858 cmdr |= ATMCI_CMDR_TRDIR_READ;
859 }
860
861 return cmdr;
862}
863
864static void atmci_send_command(struct atmel_mci *host,
865 struct mmc_command *cmd, u32 cmd_flags)
866{
867 WARN_ON(host->cmd);
868 host->cmd = cmd;
869
870 dev_vdbg(&host->pdev->dev,
871 "start command: ARGR=0x%08x CMDR=0x%08x\n",
872 cmd->arg, cmd_flags);
873
874 atmci_writel(host, ATMCI_ARGR, cmd->arg);
875 atmci_writel(host, ATMCI_CMDR, cmd_flags);
876}
877
878static void atmci_send_stop_cmd(struct atmel_mci *host, struct mmc_data *data)
879{
880 dev_dbg(&host->pdev->dev, "send stop command\n");
881 atmci_send_command(host, data->stop, host->stop_cmdr);
882 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
883}
884
885/*
886 * Configure given PDC buffer taking care of alignement issues.
887 * Update host->data_size and host->sg.
888 */
889static void atmci_pdc_set_single_buf(struct atmel_mci *host,
890 enum atmci_xfer_dir dir, enum atmci_pdc_buf buf_nb)
891{
892 u32 pointer_reg, counter_reg;
893 unsigned int buf_size;
894
895 if (dir == XFER_RECEIVE) {
896 pointer_reg = ATMEL_PDC_RPR;
897 counter_reg = ATMEL_PDC_RCR;
898 } else {
899 pointer_reg = ATMEL_PDC_TPR;
900 counter_reg = ATMEL_PDC_TCR;
901 }
902
903 if (buf_nb == PDC_SECOND_BUF) {
904 pointer_reg += ATMEL_PDC_SCND_BUF_OFF;
905 counter_reg += ATMEL_PDC_SCND_BUF_OFF;
906 }
907
908 if (!host->caps.has_rwproof) {
909 buf_size = host->buf_size;
910 atmci_writel(host, pointer_reg, host->buf_phys_addr);
911 } else {
912 buf_size = sg_dma_len(host->sg);
913 atmci_writel(host, pointer_reg, sg_dma_address(host->sg));
914 }
915
916 if (host->data_size <= buf_size) {
917 if (host->data_size & 0x3) {
918 /* If size is different from modulo 4, transfer bytes */
919 atmci_writel(host, counter_reg, host->data_size);
920 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCFBYTE);
921 } else {
922 /* Else transfer 32-bits words */
923 atmci_writel(host, counter_reg, host->data_size / 4);
924 }
925 host->data_size = 0;
926 } else {
927 /* We assume the size of a page is 32-bits aligned */
928 atmci_writel(host, counter_reg, sg_dma_len(host->sg) / 4);
929 host->data_size -= sg_dma_len(host->sg);
930 if (host->data_size)
931 host->sg = sg_next(host->sg);
932 }
933}
934
935/*
936 * Configure PDC buffer according to the data size ie configuring one or two
937 * buffers. Don't use this function if you want to configure only the second
938 * buffer. In this case, use atmci_pdc_set_single_buf.
939 */
940static void atmci_pdc_set_both_buf(struct atmel_mci *host, int dir)
941{
942 atmci_pdc_set_single_buf(host, dir, PDC_FIRST_BUF);
943 if (host->data_size)
944 atmci_pdc_set_single_buf(host, dir, PDC_SECOND_BUF);
945}
946
947/*
948 * Unmap sg lists, called when transfer is finished.
949 */
950static void atmci_pdc_cleanup(struct atmel_mci *host)
951{
952 struct mmc_data *data = host->data;
953
954 if (data)
955 dma_unmap_sg(&host->pdev->dev,
956 data->sg, data->sg_len,
957 ((data->flags & MMC_DATA_WRITE)
958 ? DMA_TO_DEVICE : DMA_FROM_DEVICE));
959}
960
961/*
962 * Disable PDC transfers. Update pending flags to EVENT_XFER_COMPLETE after
963 * having received ATMCI_TXBUFE or ATMCI_RXBUFF interrupt. Enable ATMCI_NOTBUSY
964 * interrupt needed for both transfer directions.
965 */
966static void atmci_pdc_complete(struct atmel_mci *host)
967{
968 int transfer_size = host->data->blocks * host->data->blksz;
969 int i;
970
971 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
972
973 if ((!host->caps.has_rwproof)
974 && (host->data->flags & MMC_DATA_READ)) {
975 if (host->caps.has_bad_data_ordering)
976 for (i = 0; i < transfer_size; i++)
977 host->buffer[i] = swab32(host->buffer[i]);
978 sg_copy_from_buffer(host->data->sg, host->data->sg_len,
979 host->buffer, transfer_size);
980 }
981
982 atmci_pdc_cleanup(host);
983
984 dev_dbg(&host->pdev->dev, "(%s) set pending xfer complete\n", __func__);
985 atmci_set_pending(host, EVENT_XFER_COMPLETE);
986 tasklet_schedule(&host->tasklet);
987}
988
989static void atmci_dma_cleanup(struct atmel_mci *host)
990{
991 struct mmc_data *data = host->data;
992
993 if (data)
994 dma_unmap_sg(host->dma.chan->device->dev,
995 data->sg, data->sg_len,
996 ((data->flags & MMC_DATA_WRITE)
997 ? DMA_TO_DEVICE : DMA_FROM_DEVICE));
998}
999
1000/*
1001 * This function is called by the DMA driver from tasklet context.
1002 */
1003static void atmci_dma_complete(void *arg)
1004{
1005 struct atmel_mci *host = arg;
1006 struct mmc_data *data = host->data;
1007
1008 dev_vdbg(&host->pdev->dev, "DMA complete\n");
1009
1010 if (host->caps.has_dma_conf_reg)
1011 /* Disable DMA hardware handshaking on MCI */
1012 atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN);
1013
1014 atmci_dma_cleanup(host);
1015
1016 /*
1017 * If the card was removed, data will be NULL. No point trying
1018 * to send the stop command or waiting for NBUSY in this case.
1019 */
1020 if (data) {
1021 dev_dbg(&host->pdev->dev,
1022 "(%s) set pending xfer complete\n", __func__);
1023 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1024 tasklet_schedule(&host->tasklet);
1025
1026 /*
1027 * Regardless of what the documentation says, we have
1028 * to wait for NOTBUSY even after block read
1029 * operations.
1030 *
1031 * When the DMA transfer is complete, the controller
1032 * may still be reading the CRC from the card, i.e.
1033 * the data transfer is still in progress and we
1034 * haven't seen all the potential error bits yet.
1035 *
1036 * The interrupt handler will schedule a different
1037 * tasklet to finish things up when the data transfer
1038 * is completely done.
1039 *
1040 * We may not complete the mmc request here anyway
1041 * because the mmc layer may call back and cause us to
1042 * violate the "don't submit new operations from the
1043 * completion callback" rule of the dma engine
1044 * framework.
1045 */
1046 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1047 }
1048}
1049
1050/*
1051 * Returns a mask of interrupt flags to be enabled after the whole
1052 * request has been prepared.
1053 */
1054static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
1055{
1056 u32 iflags;
1057
1058 data->error = -EINPROGRESS;
1059
1060 host->sg = data->sg;
1061 host->sg_len = data->sg_len;
1062 host->data = data;
1063 host->data_chan = NULL;
1064
1065 iflags = ATMCI_DATA_ERROR_FLAGS;
1066
1067 /*
1068 * Errata: MMC data write operation with less than 12
1069 * bytes is impossible.
1070 *
1071 * Errata: MCI Transmit Data Register (TDR) FIFO
1072 * corruption when length is not multiple of 4.
1073 */
1074 if (data->blocks * data->blksz < 12
1075 || (data->blocks * data->blksz) & 3)
1076 host->need_reset = true;
1077
1078 host->pio_offset = 0;
1079 if (data->flags & MMC_DATA_READ)
1080 iflags |= ATMCI_RXRDY;
1081 else
1082 iflags |= ATMCI_TXRDY;
1083
1084 return iflags;
1085}
1086
1087/*
1088 * Set interrupt flags and set block length into the MCI mode register even
1089 * if this value is also accessible in the MCI block register. It seems to be
1090 * necessary before the High Speed MCI version. It also map sg and configure
1091 * PDC registers.
1092 */
1093static u32
1094atmci_prepare_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1095{
1096 u32 iflags, tmp;
1097 unsigned int sg_len;
1098 enum dma_data_direction dir;
1099 int i;
1100
1101 data->error = -EINPROGRESS;
1102
1103 host->data = data;
1104 host->sg = data->sg;
1105 iflags = ATMCI_DATA_ERROR_FLAGS;
1106
1107 /* Enable pdc mode */
1108 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCMODE);
1109
1110 if (data->flags & MMC_DATA_READ) {
1111 dir = DMA_FROM_DEVICE;
1112 iflags |= ATMCI_ENDRX | ATMCI_RXBUFF;
1113 } else {
1114 dir = DMA_TO_DEVICE;
1115 iflags |= ATMCI_ENDTX | ATMCI_TXBUFE | ATMCI_BLKE;
1116 }
1117
1118 /* Set BLKLEN */
1119 tmp = atmci_readl(host, ATMCI_MR);
1120 tmp &= 0x0000ffff;
1121 tmp |= ATMCI_BLKLEN(data->blksz);
1122 atmci_writel(host, ATMCI_MR, tmp);
1123
1124 /* Configure PDC */
1125 host->data_size = data->blocks * data->blksz;
1126 sg_len = dma_map_sg(&host->pdev->dev, data->sg, data->sg_len, dir);
1127
1128 if ((!host->caps.has_rwproof)
1129 && (host->data->flags & MMC_DATA_WRITE)) {
1130 sg_copy_to_buffer(host->data->sg, host->data->sg_len,
1131 host->buffer, host->data_size);
1132 if (host->caps.has_bad_data_ordering)
1133 for (i = 0; i < host->data_size; i++)
1134 host->buffer[i] = swab32(host->buffer[i]);
1135 }
1136
1137 if (host->data_size)
1138 atmci_pdc_set_both_buf(host,
1139 ((dir == DMA_FROM_DEVICE) ? XFER_RECEIVE : XFER_TRANSMIT));
1140
1141 return iflags;
1142}
1143
1144static u32
1145atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
1146{
1147 struct dma_chan *chan;
1148 struct dma_async_tx_descriptor *desc;
1149 struct scatterlist *sg;
1150 unsigned int i;
1151 enum dma_data_direction direction;
1152 enum dma_transfer_direction slave_dirn;
1153 unsigned int sglen;
1154 u32 maxburst;
1155 u32 iflags;
1156
1157 data->error = -EINPROGRESS;
1158
1159 WARN_ON(host->data);
1160 host->sg = NULL;
1161 host->data = data;
1162
1163 iflags = ATMCI_DATA_ERROR_FLAGS;
1164
1165 /*
1166 * We don't do DMA on "complex" transfers, i.e. with
1167 * non-word-aligned buffers or lengths. Also, we don't bother
1168 * with all the DMA setup overhead for short transfers.
1169 */
1170 if (data->blocks * data->blksz < ATMCI_DMA_THRESHOLD)
1171 return atmci_prepare_data(host, data);
1172 if (data->blksz & 3)
1173 return atmci_prepare_data(host, data);
1174
1175 for_each_sg(data->sg, sg, data->sg_len, i) {
1176 if (sg->offset & 3 || sg->length & 3)
1177 return atmci_prepare_data(host, data);
1178 }
1179
1180 /* If we don't have a channel, we can't do DMA */
1181 chan = host->dma.chan;
1182 if (chan)
1183 host->data_chan = chan;
1184
1185 if (!chan)
1186 return -ENODEV;
1187
1188 if (data->flags & MMC_DATA_READ) {
1189 direction = DMA_FROM_DEVICE;
1190 host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
1191 maxburst = atmci_convert_chksize(host,
1192 host->dma_conf.src_maxburst);
1193 } else {
1194 direction = DMA_TO_DEVICE;
1195 host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
1196 maxburst = atmci_convert_chksize(host,
1197 host->dma_conf.dst_maxburst);
1198 }
1199
1200 if (host->caps.has_dma_conf_reg)
1201 atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) |
1202 ATMCI_DMAEN);
1203
1204 sglen = dma_map_sg(chan->device->dev, data->sg,
1205 data->sg_len, direction);
1206
1207 dmaengine_slave_config(chan, &host->dma_conf);
1208 desc = dmaengine_prep_slave_sg(chan,
1209 data->sg, sglen, slave_dirn,
1210 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1211 if (!desc)
1212 goto unmap_exit;
1213
1214 host->dma.data_desc = desc;
1215 desc->callback = atmci_dma_complete;
1216 desc->callback_param = host;
1217
1218 return iflags;
1219unmap_exit:
1220 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len, direction);
1221 return -ENOMEM;
1222}
1223
1224static void
1225atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
1226{
1227 return;
1228}
1229
1230/*
1231 * Start PDC according to transfer direction.
1232 */
1233static void
1234atmci_submit_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1235{
1236 if (data->flags & MMC_DATA_READ)
1237 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1238 else
1239 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1240}
1241
1242static void
1243atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
1244{
1245 struct dma_chan *chan = host->data_chan;
1246 struct dma_async_tx_descriptor *desc = host->dma.data_desc;
1247
1248 if (chan) {
1249 dmaengine_submit(desc);
1250 dma_async_issue_pending(chan);
1251 }
1252}
1253
1254static void atmci_stop_transfer(struct atmel_mci *host)
1255{
1256 dev_dbg(&host->pdev->dev,
1257 "(%s) set pending xfer complete\n", __func__);
1258 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1259 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1260}
1261
1262/*
1263 * Stop data transfer because error(s) occurred.
1264 */
1265static void atmci_stop_transfer_pdc(struct atmel_mci *host)
1266{
1267 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
1268}
1269
1270static void atmci_stop_transfer_dma(struct atmel_mci *host)
1271{
1272 struct dma_chan *chan = host->data_chan;
1273
1274 if (chan) {
1275 dmaengine_terminate_all(chan);
1276 atmci_dma_cleanup(host);
1277 } else {
1278 /* Data transfer was stopped by the interrupt handler */
1279 dev_dbg(&host->pdev->dev,
1280 "(%s) set pending xfer complete\n", __func__);
1281 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1282 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1283 }
1284}
1285
1286/*
1287 * Start a request: prepare data if needed, prepare the command and activate
1288 * interrupts.
1289 */
1290static void atmci_start_request(struct atmel_mci *host,
1291 struct atmel_mci_slot *slot)
1292{
1293 struct mmc_request *mrq;
1294 struct mmc_command *cmd;
1295 struct mmc_data *data;
1296 u32 iflags;
1297 u32 cmdflags;
1298
1299 mrq = slot->mrq;
1300 host->cur_slot = slot;
1301 host->mrq = mrq;
1302
1303 host->pending_events = 0;
1304 host->completed_events = 0;
1305 host->cmd_status = 0;
1306 host->data_status = 0;
1307
1308 dev_dbg(&host->pdev->dev, "start request: cmd %u\n", mrq->cmd->opcode);
1309
1310 if (host->need_reset || host->caps.need_reset_after_xfer) {
1311 iflags = atmci_readl(host, ATMCI_IMR);
1312 iflags &= (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB);
1313 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1314 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1315 atmci_writel(host, ATMCI_MR, host->mode_reg);
1316 if (host->caps.has_cfg_reg)
1317 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1318 atmci_writel(host, ATMCI_IER, iflags);
1319 host->need_reset = false;
1320 }
1321 atmci_writel(host, ATMCI_SDCR, slot->sdc_reg);
1322
1323 iflags = atmci_readl(host, ATMCI_IMR);
1324 if (iflags & ~(ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
1325 dev_dbg(&slot->mmc->class_dev, "WARNING: IMR=0x%08x\n",
1326 iflags);
1327
1328 if (unlikely(test_and_clear_bit(ATMCI_CARD_NEED_INIT, &slot->flags))) {
1329 /* Send init sequence (74 clock cycles) */
1330 atmci_writel(host, ATMCI_CMDR, ATMCI_CMDR_SPCMD_INIT);
1331 while (!(atmci_readl(host, ATMCI_SR) & ATMCI_CMDRDY))
1332 cpu_relax();
1333 }
1334 iflags = 0;
1335 data = mrq->data;
1336 if (data) {
1337 atmci_set_timeout(host, slot, data);
1338
1339 /* Must set block count/size before sending command */
1340 atmci_writel(host, ATMCI_BLKR, ATMCI_BCNT(data->blocks)
1341 | ATMCI_BLKLEN(data->blksz));
1342 dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n",
1343 ATMCI_BCNT(data->blocks) | ATMCI_BLKLEN(data->blksz));
1344
1345 iflags |= host->prepare_data(host, data);
1346 }
1347
1348 iflags |= ATMCI_CMDRDY;
1349 cmd = mrq->cmd;
1350 cmdflags = atmci_prepare_command(slot->mmc, cmd);
1351
1352 /*
1353 * DMA transfer should be started before sending the command to avoid
1354 * unexpected errors especially for read operations in SDIO mode.
1355 * Unfortunately, in PDC mode, command has to be sent before starting
1356 * the transfer.
1357 */
1358 if (host->submit_data != &atmci_submit_data_dma)
1359 atmci_send_command(host, cmd, cmdflags);
1360
1361 if (data)
1362 host->submit_data(host, data);
1363
1364 if (host->submit_data == &atmci_submit_data_dma)
1365 atmci_send_command(host, cmd, cmdflags);
1366
1367 if (mrq->stop) {
1368 host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop);
1369 host->stop_cmdr |= ATMCI_CMDR_STOP_XFER;
1370 if (!(data->flags & MMC_DATA_WRITE))
1371 host->stop_cmdr |= ATMCI_CMDR_TRDIR_READ;
1372 host->stop_cmdr |= ATMCI_CMDR_MULTI_BLOCK;
1373 }
1374
1375 /*
1376 * We could have enabled interrupts earlier, but I suspect
1377 * that would open up a nice can of interesting race
1378 * conditions (e.g. command and data complete, but stop not
1379 * prepared yet.)
1380 */
1381 atmci_writel(host, ATMCI_IER, iflags);
1382
1383 mod_timer(&host->timer, jiffies + msecs_to_jiffies(2000));
1384}
1385
1386static void atmci_queue_request(struct atmel_mci *host,
1387 struct atmel_mci_slot *slot, struct mmc_request *mrq)
1388{
1389 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1390 host->state);
1391
1392 spin_lock_bh(&host->lock);
1393 slot->mrq = mrq;
1394 if (host->state == STATE_IDLE) {
1395 host->state = STATE_SENDING_CMD;
1396 atmci_start_request(host, slot);
1397 } else {
1398 dev_dbg(&host->pdev->dev, "queue request\n");
1399 list_add_tail(&slot->queue_node, &host->queue);
1400 }
1401 spin_unlock_bh(&host->lock);
1402}
1403
1404static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1405{
1406 struct atmel_mci_slot *slot = mmc_priv(mmc);
1407 struct atmel_mci *host = slot->host;
1408 struct mmc_data *data;
1409
1410 WARN_ON(slot->mrq);
1411 dev_dbg(&host->pdev->dev, "MRQ: cmd %u\n", mrq->cmd->opcode);
1412
1413 /*
1414 * We may "know" the card is gone even though there's still an
1415 * electrical connection. If so, we really need to communicate
1416 * this to the MMC core since there won't be any more
1417 * interrupts as the card is completely removed. Otherwise,
1418 * the MMC core might believe the card is still there even
1419 * though the card was just removed very slowly.
1420 */
1421 if (!test_bit(ATMCI_CARD_PRESENT, &slot->flags)) {
1422 mrq->cmd->error = -ENOMEDIUM;
1423 mmc_request_done(mmc, mrq);
1424 return;
1425 }
1426
1427 /* We don't support multiple blocks of weird lengths. */
1428 data = mrq->data;
1429 if (data && data->blocks > 1 && data->blksz & 3) {
1430 mrq->cmd->error = -EINVAL;
1431 mmc_request_done(mmc, mrq);
1432 }
1433
1434 atmci_queue_request(host, slot, mrq);
1435}
1436
1437static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1438{
1439 struct atmel_mci_slot *slot = mmc_priv(mmc);
1440 struct atmel_mci *host = slot->host;
1441 unsigned int i;
1442
1443 slot->sdc_reg &= ~ATMCI_SDCBUS_MASK;
1444 switch (ios->bus_width) {
1445 case MMC_BUS_WIDTH_1:
1446 slot->sdc_reg |= ATMCI_SDCBUS_1BIT;
1447 break;
1448 case MMC_BUS_WIDTH_4:
1449 slot->sdc_reg |= ATMCI_SDCBUS_4BIT;
1450 break;
1451 }
1452
1453 if (ios->clock) {
1454 unsigned int clock_min = ~0U;
1455 int clkdiv;
1456
1457 spin_lock_bh(&host->lock);
1458 if (!host->mode_reg) {
1459 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1460 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1461 if (host->caps.has_cfg_reg)
1462 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1463 }
1464
1465 /*
1466 * Use mirror of ios->clock to prevent race with mmc
1467 * core ios update when finding the minimum.
1468 */
1469 slot->clock = ios->clock;
1470 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1471 if (host->slot[i] && host->slot[i]->clock
1472 && host->slot[i]->clock < clock_min)
1473 clock_min = host->slot[i]->clock;
1474 }
1475
1476 /* Calculate clock divider */
1477 if (host->caps.has_odd_clk_div) {
1478 clkdiv = DIV_ROUND_UP(host->bus_hz, clock_min) - 2;
1479 if (clkdiv < 0) {
1480 dev_warn(&mmc->class_dev,
1481 "clock %u too fast; using %lu\n",
1482 clock_min, host->bus_hz / 2);
1483 clkdiv = 0;
1484 } else if (clkdiv > 511) {
1485 dev_warn(&mmc->class_dev,
1486 "clock %u too slow; using %lu\n",
1487 clock_min, host->bus_hz / (511 + 2));
1488 clkdiv = 511;
1489 }
1490 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv >> 1)
1491 | ATMCI_MR_CLKODD(clkdiv & 1);
1492 } else {
1493 clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * clock_min) - 1;
1494 if (clkdiv > 255) {
1495 dev_warn(&mmc->class_dev,
1496 "clock %u too slow; using %lu\n",
1497 clock_min, host->bus_hz / (2 * 256));
1498 clkdiv = 255;
1499 }
1500 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv);
1501 }
1502
1503 /*
1504 * WRPROOF and RDPROOF prevent overruns/underruns by
1505 * stopping the clock when the FIFO is full/empty.
1506 * This state is not expected to last for long.
1507 */
1508 if (host->caps.has_rwproof)
1509 host->mode_reg |= (ATMCI_MR_WRPROOF | ATMCI_MR_RDPROOF);
1510
1511 if (host->caps.has_cfg_reg) {
1512 /* setup High Speed mode in relation with card capacity */
1513 if (ios->timing == MMC_TIMING_SD_HS)
1514 host->cfg_reg |= ATMCI_CFG_HSMODE;
1515 else
1516 host->cfg_reg &= ~ATMCI_CFG_HSMODE;
1517 }
1518
1519 if (list_empty(&host->queue)) {
1520 atmci_writel(host, ATMCI_MR, host->mode_reg);
1521 if (host->caps.has_cfg_reg)
1522 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1523 } else {
1524 host->need_clock_update = true;
1525 }
1526
1527 spin_unlock_bh(&host->lock);
1528 } else {
1529 bool any_slot_active = false;
1530
1531 spin_lock_bh(&host->lock);
1532 slot->clock = 0;
1533 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1534 if (host->slot[i] && host->slot[i]->clock) {
1535 any_slot_active = true;
1536 break;
1537 }
1538 }
1539 if (!any_slot_active) {
1540 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
1541 if (host->mode_reg) {
1542 atmci_readl(host, ATMCI_MR);
1543 }
1544 host->mode_reg = 0;
1545 }
1546 spin_unlock_bh(&host->lock);
1547 }
1548
1549 switch (ios->power_mode) {
1550 case MMC_POWER_OFF:
1551 if (!IS_ERR(mmc->supply.vmmc))
1552 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1553 break;
1554 case MMC_POWER_UP:
1555 set_bit(ATMCI_CARD_NEED_INIT, &slot->flags);
1556 if (!IS_ERR(mmc->supply.vmmc))
1557 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
1558 break;
1559 default:
1560 /*
1561 * TODO: None of the currently available AVR32-based
1562 * boards allow MMC power to be turned off. Implement
1563 * power control when this can be tested properly.
1564 *
1565 * We also need to hook this into the clock management
1566 * somehow so that newly inserted cards aren't
1567 * subjected to a fast clock before we have a chance
1568 * to figure out what the maximum rate is. Currently,
1569 * there's no way to avoid this, and there never will
1570 * be for boards that don't support power control.
1571 */
1572 break;
1573 }
1574
1575}
1576
1577static int atmci_get_ro(struct mmc_host *mmc)
1578{
1579 int read_only = -ENOSYS;
1580 struct atmel_mci_slot *slot = mmc_priv(mmc);
1581
1582 if (gpio_is_valid(slot->wp_pin)) {
1583 read_only = gpio_get_value(slot->wp_pin);
1584 dev_dbg(&mmc->class_dev, "card is %s\n",
1585 read_only ? "read-only" : "read-write");
1586 }
1587
1588 return read_only;
1589}
1590
1591static int atmci_get_cd(struct mmc_host *mmc)
1592{
1593 int present = -ENOSYS;
1594 struct atmel_mci_slot *slot = mmc_priv(mmc);
1595
1596 if (gpio_is_valid(slot->detect_pin)) {
1597 present = !(gpio_get_value(slot->detect_pin) ^
1598 slot->detect_is_active_high);
1599 dev_dbg(&mmc->class_dev, "card is %spresent\n",
1600 present ? "" : "not ");
1601 }
1602
1603 return present;
1604}
1605
1606static void atmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1607{
1608 struct atmel_mci_slot *slot = mmc_priv(mmc);
1609 struct atmel_mci *host = slot->host;
1610
1611 if (enable)
1612 atmci_writel(host, ATMCI_IER, slot->sdio_irq);
1613 else
1614 atmci_writel(host, ATMCI_IDR, slot->sdio_irq);
1615}
1616
1617static const struct mmc_host_ops atmci_ops = {
1618 .request = atmci_request,
1619 .set_ios = atmci_set_ios,
1620 .get_ro = atmci_get_ro,
1621 .get_cd = atmci_get_cd,
1622 .enable_sdio_irq = atmci_enable_sdio_irq,
1623};
1624
1625/* Called with host->lock held */
1626static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq)
1627 __releases(&host->lock)
1628 __acquires(&host->lock)
1629{
1630 struct atmel_mci_slot *slot = NULL;
1631 struct mmc_host *prev_mmc = host->cur_slot->mmc;
1632
1633 WARN_ON(host->cmd || host->data);
1634
1635 /*
1636 * Update the MMC clock rate if necessary. This may be
1637 * necessary if set_ios() is called when a different slot is
1638 * busy transferring data.
1639 */
1640 if (host->need_clock_update) {
1641 atmci_writel(host, ATMCI_MR, host->mode_reg);
1642 if (host->caps.has_cfg_reg)
1643 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1644 }
1645
1646 host->cur_slot->mrq = NULL;
1647 host->mrq = NULL;
1648 if (!list_empty(&host->queue)) {
1649 slot = list_entry(host->queue.next,
1650 struct atmel_mci_slot, queue_node);
1651 list_del(&slot->queue_node);
1652 dev_vdbg(&host->pdev->dev, "list not empty: %s is next\n",
1653 mmc_hostname(slot->mmc));
1654 host->state = STATE_SENDING_CMD;
1655 atmci_start_request(host, slot);
1656 } else {
1657 dev_vdbg(&host->pdev->dev, "list empty\n");
1658 host->state = STATE_IDLE;
1659 }
1660
1661 del_timer(&host->timer);
1662
1663 spin_unlock(&host->lock);
1664 mmc_request_done(prev_mmc, mrq);
1665 spin_lock(&host->lock);
1666}
1667
1668static void atmci_command_complete(struct atmel_mci *host,
1669 struct mmc_command *cmd)
1670{
1671 u32 status = host->cmd_status;
1672
1673 /* Read the response from the card (up to 16 bytes) */
1674 cmd->resp[0] = atmci_readl(host, ATMCI_RSPR);
1675 cmd->resp[1] = atmci_readl(host, ATMCI_RSPR);
1676 cmd->resp[2] = atmci_readl(host, ATMCI_RSPR);
1677 cmd->resp[3] = atmci_readl(host, ATMCI_RSPR);
1678
1679 if (status & ATMCI_RTOE)
1680 cmd->error = -ETIMEDOUT;
1681 else if ((cmd->flags & MMC_RSP_CRC) && (status & ATMCI_RCRCE))
1682 cmd->error = -EILSEQ;
1683 else if (status & (ATMCI_RINDE | ATMCI_RDIRE | ATMCI_RENDE))
1684 cmd->error = -EIO;
1685 else if (host->mrq->data && (host->mrq->data->blksz & 3)) {
1686 if (host->caps.need_blksz_mul_4) {
1687 cmd->error = -EINVAL;
1688 host->need_reset = 1;
1689 }
1690 } else
1691 cmd->error = 0;
1692}
1693
1694static void atmci_detect_change(unsigned long data)
1695{
1696 struct atmel_mci_slot *slot = (struct atmel_mci_slot *)data;
1697 bool present;
1698 bool present_old;
1699
1700 /*
1701 * atmci_cleanup_slot() sets the ATMCI_SHUTDOWN flag before
1702 * freeing the interrupt. We must not re-enable the interrupt
1703 * if it has been freed, and if we're shutting down, it
1704 * doesn't really matter whether the card is present or not.
1705 */
1706 smp_rmb();
1707 if (test_bit(ATMCI_SHUTDOWN, &slot->flags))
1708 return;
1709
1710 enable_irq(gpio_to_irq(slot->detect_pin));
1711 present = !(gpio_get_value(slot->detect_pin) ^
1712 slot->detect_is_active_high);
1713 present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
1714
1715 dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
1716 present, present_old);
1717
1718 if (present != present_old) {
1719 struct atmel_mci *host = slot->host;
1720 struct mmc_request *mrq;
1721
1722 dev_dbg(&slot->mmc->class_dev, "card %s\n",
1723 present ? "inserted" : "removed");
1724
1725 spin_lock(&host->lock);
1726
1727 if (!present)
1728 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
1729 else
1730 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
1731
1732 /* Clean up queue if present */
1733 mrq = slot->mrq;
1734 if (mrq) {
1735 if (mrq == host->mrq) {
1736 /*
1737 * Reset controller to terminate any ongoing
1738 * commands or data transfers.
1739 */
1740 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1741 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1742 atmci_writel(host, ATMCI_MR, host->mode_reg);
1743 if (host->caps.has_cfg_reg)
1744 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1745
1746 host->data = NULL;
1747 host->cmd = NULL;
1748
1749 switch (host->state) {
1750 case STATE_IDLE:
1751 break;
1752 case STATE_SENDING_CMD:
1753 mrq->cmd->error = -ENOMEDIUM;
1754 if (mrq->data)
1755 host->stop_transfer(host);
1756 break;
1757 case STATE_DATA_XFER:
1758 mrq->data->error = -ENOMEDIUM;
1759 host->stop_transfer(host);
1760 break;
1761 case STATE_WAITING_NOTBUSY:
1762 mrq->data->error = -ENOMEDIUM;
1763 break;
1764 case STATE_SENDING_STOP:
1765 mrq->stop->error = -ENOMEDIUM;
1766 break;
1767 case STATE_END_REQUEST:
1768 break;
1769 }
1770
1771 atmci_request_end(host, mrq);
1772 } else {
1773 list_del(&slot->queue_node);
1774 mrq->cmd->error = -ENOMEDIUM;
1775 if (mrq->data)
1776 mrq->data->error = -ENOMEDIUM;
1777 if (mrq->stop)
1778 mrq->stop->error = -ENOMEDIUM;
1779
1780 spin_unlock(&host->lock);
1781 mmc_request_done(slot->mmc, mrq);
1782 spin_lock(&host->lock);
1783 }
1784 }
1785 spin_unlock(&host->lock);
1786
1787 mmc_detect_change(slot->mmc, 0);
1788 }
1789}
1790
1791static void atmci_tasklet_func(unsigned long priv)
1792{
1793 struct atmel_mci *host = (struct atmel_mci *)priv;
1794 struct mmc_request *mrq = host->mrq;
1795 struct mmc_data *data = host->data;
1796 enum atmel_mci_state state = host->state;
1797 enum atmel_mci_state prev_state;
1798 u32 status;
1799
1800 spin_lock(&host->lock);
1801
1802 state = host->state;
1803
1804 dev_vdbg(&host->pdev->dev,
1805 "tasklet: state %u pending/completed/mask %lx/%lx/%x\n",
1806 state, host->pending_events, host->completed_events,
1807 atmci_readl(host, ATMCI_IMR));
1808
1809 do {
1810 prev_state = state;
1811 dev_dbg(&host->pdev->dev, "FSM: state=%d\n", state);
1812
1813 switch (state) {
1814 case STATE_IDLE:
1815 break;
1816
1817 case STATE_SENDING_CMD:
1818 /*
1819 * Command has been sent, we are waiting for command
1820 * ready. Then we have three next states possible:
1821 * END_REQUEST by default, WAITING_NOTBUSY if it's a
1822 * command needing it or DATA_XFER if there is data.
1823 */
1824 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1825 if (!atmci_test_and_clear_pending(host,
1826 EVENT_CMD_RDY))
1827 break;
1828
1829 dev_dbg(&host->pdev->dev, "set completed cmd ready\n");
1830 host->cmd = NULL;
1831 atmci_set_completed(host, EVENT_CMD_RDY);
1832 atmci_command_complete(host, mrq->cmd);
1833 if (mrq->data) {
1834 dev_dbg(&host->pdev->dev,
1835 "command with data transfer");
1836 /*
1837 * If there is a command error don't start
1838 * data transfer.
1839 */
1840 if (mrq->cmd->error) {
1841 host->stop_transfer(host);
1842 host->data = NULL;
1843 atmci_writel(host, ATMCI_IDR,
1844 ATMCI_TXRDY | ATMCI_RXRDY
1845 | ATMCI_DATA_ERROR_FLAGS);
1846 state = STATE_END_REQUEST;
1847 } else
1848 state = STATE_DATA_XFER;
1849 } else if ((!mrq->data) && (mrq->cmd->flags & MMC_RSP_BUSY)) {
1850 dev_dbg(&host->pdev->dev,
1851 "command response need waiting notbusy");
1852 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1853 state = STATE_WAITING_NOTBUSY;
1854 } else
1855 state = STATE_END_REQUEST;
1856
1857 break;
1858
1859 case STATE_DATA_XFER:
1860 if (atmci_test_and_clear_pending(host,
1861 EVENT_DATA_ERROR)) {
1862 dev_dbg(&host->pdev->dev, "set completed data error\n");
1863 atmci_set_completed(host, EVENT_DATA_ERROR);
1864 state = STATE_END_REQUEST;
1865 break;
1866 }
1867
1868 /*
1869 * A data transfer is in progress. The event expected
1870 * to move to the next state depends of data transfer
1871 * type (PDC or DMA). Once transfer done we can move
1872 * to the next step which is WAITING_NOTBUSY in write
1873 * case and directly SENDING_STOP in read case.
1874 */
1875 dev_dbg(&host->pdev->dev, "FSM: xfer complete?\n");
1876 if (!atmci_test_and_clear_pending(host,
1877 EVENT_XFER_COMPLETE))
1878 break;
1879
1880 dev_dbg(&host->pdev->dev,
1881 "(%s) set completed xfer complete\n",
1882 __func__);
1883 atmci_set_completed(host, EVENT_XFER_COMPLETE);
1884
1885 if (host->caps.need_notbusy_for_read_ops ||
1886 (host->data->flags & MMC_DATA_WRITE)) {
1887 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1888 state = STATE_WAITING_NOTBUSY;
1889 } else if (host->mrq->stop) {
1890 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
1891 atmci_send_stop_cmd(host, data);
1892 state = STATE_SENDING_STOP;
1893 } else {
1894 host->data = NULL;
1895 data->bytes_xfered = data->blocks * data->blksz;
1896 data->error = 0;
1897 state = STATE_END_REQUEST;
1898 }
1899 break;
1900
1901 case STATE_WAITING_NOTBUSY:
1902 /*
1903 * We can be in the state for two reasons: a command
1904 * requiring waiting not busy signal (stop command
1905 * included) or a write operation. In the latest case,
1906 * we need to send a stop command.
1907 */
1908 dev_dbg(&host->pdev->dev, "FSM: not busy?\n");
1909 if (!atmci_test_and_clear_pending(host,
1910 EVENT_NOTBUSY))
1911 break;
1912
1913 dev_dbg(&host->pdev->dev, "set completed not busy\n");
1914 atmci_set_completed(host, EVENT_NOTBUSY);
1915
1916 if (host->data) {
1917 /*
1918 * For some commands such as CMD53, even if
1919 * there is data transfer, there is no stop
1920 * command to send.
1921 */
1922 if (host->mrq->stop) {
1923 atmci_writel(host, ATMCI_IER,
1924 ATMCI_CMDRDY);
1925 atmci_send_stop_cmd(host, data);
1926 state = STATE_SENDING_STOP;
1927 } else {
1928 host->data = NULL;
1929 data->bytes_xfered = data->blocks
1930 * data->blksz;
1931 data->error = 0;
1932 state = STATE_END_REQUEST;
1933 }
1934 } else
1935 state = STATE_END_REQUEST;
1936 break;
1937
1938 case STATE_SENDING_STOP:
1939 /*
1940 * In this state, it is important to set host->data to
1941 * NULL (which is tested in the waiting notbusy state)
1942 * in order to go to the end request state instead of
1943 * sending stop again.
1944 */
1945 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1946 if (!atmci_test_and_clear_pending(host,
1947 EVENT_CMD_RDY))
1948 break;
1949
1950 dev_dbg(&host->pdev->dev, "FSM: cmd ready\n");
1951 host->cmd = NULL;
1952 data->bytes_xfered = data->blocks * data->blksz;
1953 data->error = 0;
1954 atmci_command_complete(host, mrq->stop);
1955 if (mrq->stop->error) {
1956 host->stop_transfer(host);
1957 atmci_writel(host, ATMCI_IDR,
1958 ATMCI_TXRDY | ATMCI_RXRDY
1959 | ATMCI_DATA_ERROR_FLAGS);
1960 state = STATE_END_REQUEST;
1961 } else {
1962 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1963 state = STATE_WAITING_NOTBUSY;
1964 }
1965 host->data = NULL;
1966 break;
1967
1968 case STATE_END_REQUEST:
1969 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY | ATMCI_RXRDY
1970 | ATMCI_DATA_ERROR_FLAGS);
1971 status = host->data_status;
1972 if (unlikely(status)) {
1973 host->stop_transfer(host);
1974 host->data = NULL;
1975 if (data) {
1976 if (status & ATMCI_DTOE) {
1977 data->error = -ETIMEDOUT;
1978 } else if (status & ATMCI_DCRCE) {
1979 data->error = -EILSEQ;
1980 } else {
1981 data->error = -EIO;
1982 }
1983 }
1984 }
1985
1986 atmci_request_end(host, host->mrq);
1987 state = STATE_IDLE;
1988 break;
1989 }
1990 } while (state != prev_state);
1991
1992 host->state = state;
1993
1994 spin_unlock(&host->lock);
1995}
1996
1997static void atmci_read_data_pio(struct atmel_mci *host)
1998{
1999 struct scatterlist *sg = host->sg;
2000 void *buf = sg_virt(sg);
2001 unsigned int offset = host->pio_offset;
2002 struct mmc_data *data = host->data;
2003 u32 value;
2004 u32 status;
2005 unsigned int nbytes = 0;
2006
2007 do {
2008 value = atmci_readl(host, ATMCI_RDR);
2009 if (likely(offset + 4 <= sg->length)) {
2010 put_unaligned(value, (u32 *)(buf + offset));
2011
2012 offset += 4;
2013 nbytes += 4;
2014
2015 if (offset == sg->length) {
2016 flush_dcache_page(sg_page(sg));
2017 host->sg = sg = sg_next(sg);
2018 host->sg_len--;
2019 if (!sg || !host->sg_len)
2020 goto done;
2021
2022 offset = 0;
2023 buf = sg_virt(sg);
2024 }
2025 } else {
2026 unsigned int remaining = sg->length - offset;
2027 memcpy(buf + offset, &value, remaining);
2028 nbytes += remaining;
2029
2030 flush_dcache_page(sg_page(sg));
2031 host->sg = sg = sg_next(sg);
2032 host->sg_len--;
2033 if (!sg || !host->sg_len)
2034 goto done;
2035
2036 offset = 4 - remaining;
2037 buf = sg_virt(sg);
2038 memcpy(buf, (u8 *)&value + remaining, offset);
2039 nbytes += offset;
2040 }
2041
2042 status = atmci_readl(host, ATMCI_SR);
2043 if (status & ATMCI_DATA_ERROR_FLAGS) {
2044 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_RXRDY
2045 | ATMCI_DATA_ERROR_FLAGS));
2046 host->data_status = status;
2047 data->bytes_xfered += nbytes;
2048 return;
2049 }
2050 } while (status & ATMCI_RXRDY);
2051
2052 host->pio_offset = offset;
2053 data->bytes_xfered += nbytes;
2054
2055 return;
2056
2057done:
2058 atmci_writel(host, ATMCI_IDR, ATMCI_RXRDY);
2059 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2060 data->bytes_xfered += nbytes;
2061 smp_wmb();
2062 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2063}
2064
2065static void atmci_write_data_pio(struct atmel_mci *host)
2066{
2067 struct scatterlist *sg = host->sg;
2068 void *buf = sg_virt(sg);
2069 unsigned int offset = host->pio_offset;
2070 struct mmc_data *data = host->data;
2071 u32 value;
2072 u32 status;
2073 unsigned int nbytes = 0;
2074
2075 do {
2076 if (likely(offset + 4 <= sg->length)) {
2077 value = get_unaligned((u32 *)(buf + offset));
2078 atmci_writel(host, ATMCI_TDR, value);
2079
2080 offset += 4;
2081 nbytes += 4;
2082 if (offset == sg->length) {
2083 host->sg = sg = sg_next(sg);
2084 host->sg_len--;
2085 if (!sg || !host->sg_len)
2086 goto done;
2087
2088 offset = 0;
2089 buf = sg_virt(sg);
2090 }
2091 } else {
2092 unsigned int remaining = sg->length - offset;
2093
2094 value = 0;
2095 memcpy(&value, buf + offset, remaining);
2096 nbytes += remaining;
2097
2098 host->sg = sg = sg_next(sg);
2099 host->sg_len--;
2100 if (!sg || !host->sg_len) {
2101 atmci_writel(host, ATMCI_TDR, value);
2102 goto done;
2103 }
2104
2105 offset = 4 - remaining;
2106 buf = sg_virt(sg);
2107 memcpy((u8 *)&value + remaining, buf, offset);
2108 atmci_writel(host, ATMCI_TDR, value);
2109 nbytes += offset;
2110 }
2111
2112 status = atmci_readl(host, ATMCI_SR);
2113 if (status & ATMCI_DATA_ERROR_FLAGS) {
2114 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_TXRDY
2115 | ATMCI_DATA_ERROR_FLAGS));
2116 host->data_status = status;
2117 data->bytes_xfered += nbytes;
2118 return;
2119 }
2120 } while (status & ATMCI_TXRDY);
2121
2122 host->pio_offset = offset;
2123 data->bytes_xfered += nbytes;
2124
2125 return;
2126
2127done:
2128 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY);
2129 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2130 data->bytes_xfered += nbytes;
2131 smp_wmb();
2132 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2133}
2134
2135static void atmci_sdio_interrupt(struct atmel_mci *host, u32 status)
2136{
2137 int i;
2138
2139 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2140 struct atmel_mci_slot *slot = host->slot[i];
2141 if (slot && (status & slot->sdio_irq)) {
2142 mmc_signal_sdio_irq(slot->mmc);
2143 }
2144 }
2145}
2146
2147
2148static irqreturn_t atmci_interrupt(int irq, void *dev_id)
2149{
2150 struct atmel_mci *host = dev_id;
2151 u32 status, mask, pending;
2152 unsigned int pass_count = 0;
2153
2154 do {
2155 status = atmci_readl(host, ATMCI_SR);
2156 mask = atmci_readl(host, ATMCI_IMR);
2157 pending = status & mask;
2158 if (!pending)
2159 break;
2160
2161 if (pending & ATMCI_DATA_ERROR_FLAGS) {
2162 dev_dbg(&host->pdev->dev, "IRQ: data error\n");
2163 atmci_writel(host, ATMCI_IDR, ATMCI_DATA_ERROR_FLAGS
2164 | ATMCI_RXRDY | ATMCI_TXRDY
2165 | ATMCI_ENDRX | ATMCI_ENDTX
2166 | ATMCI_RXBUFF | ATMCI_TXBUFE);
2167
2168 host->data_status = status;
2169 dev_dbg(&host->pdev->dev, "set pending data error\n");
2170 smp_wmb();
2171 atmci_set_pending(host, EVENT_DATA_ERROR);
2172 tasklet_schedule(&host->tasklet);
2173 }
2174
2175 if (pending & ATMCI_TXBUFE) {
2176 dev_dbg(&host->pdev->dev, "IRQ: tx buffer empty\n");
2177 atmci_writel(host, ATMCI_IDR, ATMCI_TXBUFE);
2178 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2179 /*
2180 * We can receive this interruption before having configured
2181 * the second pdc buffer, so we need to reconfigure first and
2182 * second buffers again
2183 */
2184 if (host->data_size) {
2185 atmci_pdc_set_both_buf(host, XFER_TRANSMIT);
2186 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2187 atmci_writel(host, ATMCI_IER, ATMCI_TXBUFE);
2188 } else {
2189 atmci_pdc_complete(host);
2190 }
2191 } else if (pending & ATMCI_ENDTX) {
2192 dev_dbg(&host->pdev->dev, "IRQ: end of tx buffer\n");
2193 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2194
2195 if (host->data_size) {
2196 atmci_pdc_set_single_buf(host,
2197 XFER_TRANSMIT, PDC_SECOND_BUF);
2198 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2199 }
2200 }
2201
2202 if (pending & ATMCI_RXBUFF) {
2203 dev_dbg(&host->pdev->dev, "IRQ: rx buffer full\n");
2204 atmci_writel(host, ATMCI_IDR, ATMCI_RXBUFF);
2205 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2206 /*
2207 * We can receive this interruption before having configured
2208 * the second pdc buffer, so we need to reconfigure first and
2209 * second buffers again
2210 */
2211 if (host->data_size) {
2212 atmci_pdc_set_both_buf(host, XFER_RECEIVE);
2213 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2214 atmci_writel(host, ATMCI_IER, ATMCI_RXBUFF);
2215 } else {
2216 atmci_pdc_complete(host);
2217 }
2218 } else if (pending & ATMCI_ENDRX) {
2219 dev_dbg(&host->pdev->dev, "IRQ: end of rx buffer\n");
2220 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2221
2222 if (host->data_size) {
2223 atmci_pdc_set_single_buf(host,
2224 XFER_RECEIVE, PDC_SECOND_BUF);
2225 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2226 }
2227 }
2228
2229 /*
2230 * First mci IPs, so mainly the ones having pdc, have some
2231 * issues with the notbusy signal. You can't get it after
2232 * data transmission if you have not sent a stop command.
2233 * The appropriate workaround is to use the BLKE signal.
2234 */
2235 if (pending & ATMCI_BLKE) {
2236 dev_dbg(&host->pdev->dev, "IRQ: blke\n");
2237 atmci_writel(host, ATMCI_IDR, ATMCI_BLKE);
2238 smp_wmb();
2239 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2240 atmci_set_pending(host, EVENT_NOTBUSY);
2241 tasklet_schedule(&host->tasklet);
2242 }
2243
2244 if (pending & ATMCI_NOTBUSY) {
2245 dev_dbg(&host->pdev->dev, "IRQ: not_busy\n");
2246 atmci_writel(host, ATMCI_IDR, ATMCI_NOTBUSY);
2247 smp_wmb();
2248 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2249 atmci_set_pending(host, EVENT_NOTBUSY);
2250 tasklet_schedule(&host->tasklet);
2251 }
2252
2253 if (pending & ATMCI_RXRDY)
2254 atmci_read_data_pio(host);
2255 if (pending & ATMCI_TXRDY)
2256 atmci_write_data_pio(host);
2257
2258 if (pending & ATMCI_CMDRDY) {
2259 dev_dbg(&host->pdev->dev, "IRQ: cmd ready\n");
2260 atmci_writel(host, ATMCI_IDR, ATMCI_CMDRDY);
2261 host->cmd_status = status;
2262 smp_wmb();
2263 dev_dbg(&host->pdev->dev, "set pending cmd rdy\n");
2264 atmci_set_pending(host, EVENT_CMD_RDY);
2265 tasklet_schedule(&host->tasklet);
2266 }
2267
2268 if (pending & (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
2269 atmci_sdio_interrupt(host, status);
2270
2271 } while (pass_count++ < 5);
2272
2273 return pass_count ? IRQ_HANDLED : IRQ_NONE;
2274}
2275
2276static irqreturn_t atmci_detect_interrupt(int irq, void *dev_id)
2277{
2278 struct atmel_mci_slot *slot = dev_id;
2279
2280 /*
2281 * Disable interrupts until the pin has stabilized and check
2282 * the state then. Use mod_timer() since we may be in the
2283 * middle of the timer routine when this interrupt triggers.
2284 */
2285 disable_irq_nosync(irq);
2286 mod_timer(&slot->detect_timer, jiffies + msecs_to_jiffies(20));
2287
2288 return IRQ_HANDLED;
2289}
2290
2291static int atmci_init_slot(struct atmel_mci *host,
2292 struct mci_slot_pdata *slot_data, unsigned int id,
2293 u32 sdc_reg, u32 sdio_irq)
2294{
2295 struct mmc_host *mmc;
2296 struct atmel_mci_slot *slot;
2297
2298 mmc = mmc_alloc_host(sizeof(struct atmel_mci_slot), &host->pdev->dev);
2299 if (!mmc)
2300 return -ENOMEM;
2301
2302 slot = mmc_priv(mmc);
2303 slot->mmc = mmc;
2304 slot->host = host;
2305 slot->detect_pin = slot_data->detect_pin;
2306 slot->wp_pin = slot_data->wp_pin;
2307 slot->detect_is_active_high = slot_data->detect_is_active_high;
2308 slot->sdc_reg = sdc_reg;
2309 slot->sdio_irq = sdio_irq;
2310
2311 dev_dbg(&mmc->class_dev,
2312 "slot[%u]: bus_width=%u, detect_pin=%d, "
2313 "detect_is_active_high=%s, wp_pin=%d\n",
2314 id, slot_data->bus_width, slot_data->detect_pin,
2315 slot_data->detect_is_active_high ? "true" : "false",
2316 slot_data->wp_pin);
2317
2318 mmc->ops = &atmci_ops;
2319 mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
2320 mmc->f_max = host->bus_hz / 2;
2321 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2322 if (sdio_irq)
2323 mmc->caps |= MMC_CAP_SDIO_IRQ;
2324 if (host->caps.has_highspeed)
2325 mmc->caps |= MMC_CAP_SD_HIGHSPEED;
2326 /*
2327 * Without the read/write proof capability, it is strongly suggested to
2328 * use only one bit for data to prevent fifo underruns and overruns
2329 * which will corrupt data.
2330 */
2331 if ((slot_data->bus_width >= 4) && host->caps.has_rwproof)
2332 mmc->caps |= MMC_CAP_4_BIT_DATA;
2333
2334 if (atmci_get_version(host) < 0x200) {
2335 mmc->max_segs = 256;
2336 mmc->max_blk_size = 4095;
2337 mmc->max_blk_count = 256;
2338 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2339 mmc->max_seg_size = mmc->max_blk_size * mmc->max_segs;
2340 } else {
2341 mmc->max_segs = 64;
2342 mmc->max_req_size = 32768 * 512;
2343 mmc->max_blk_size = 32768;
2344 mmc->max_blk_count = 512;
2345 }
2346
2347 /* Assume card is present initially */
2348 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
2349 if (gpio_is_valid(slot->detect_pin)) {
2350 if (devm_gpio_request(&host->pdev->dev, slot->detect_pin,
2351 "mmc_detect")) {
2352 dev_dbg(&mmc->class_dev, "no detect pin available\n");
2353 slot->detect_pin = -EBUSY;
2354 } else if (gpio_get_value(slot->detect_pin) ^
2355 slot->detect_is_active_high) {
2356 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
2357 }
2358 }
2359
2360 if (!gpio_is_valid(slot->detect_pin)) {
2361 if (slot_data->non_removable)
2362 mmc->caps |= MMC_CAP_NONREMOVABLE;
2363 else
2364 mmc->caps |= MMC_CAP_NEEDS_POLL;
2365 }
2366
2367 if (gpio_is_valid(slot->wp_pin)) {
2368 if (devm_gpio_request(&host->pdev->dev, slot->wp_pin,
2369 "mmc_wp")) {
2370 dev_dbg(&mmc->class_dev, "no WP pin available\n");
2371 slot->wp_pin = -EBUSY;
2372 }
2373 }
2374
2375 host->slot[id] = slot;
2376 mmc_regulator_get_supply(mmc);
2377 mmc_add_host(mmc);
2378
2379 if (gpio_is_valid(slot->detect_pin)) {
2380 int ret;
2381
2382 setup_timer(&slot->detect_timer, atmci_detect_change,
2383 (unsigned long)slot);
2384
2385 ret = request_irq(gpio_to_irq(slot->detect_pin),
2386 atmci_detect_interrupt,
2387 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
2388 "mmc-detect", slot);
2389 if (ret) {
2390 dev_dbg(&mmc->class_dev,
2391 "could not request IRQ %d for detect pin\n",
2392 gpio_to_irq(slot->detect_pin));
2393 slot->detect_pin = -EBUSY;
2394 }
2395 }
2396
2397 atmci_init_debugfs(slot);
2398
2399 return 0;
2400}
2401
2402static void atmci_cleanup_slot(struct atmel_mci_slot *slot,
2403 unsigned int id)
2404{
2405 /* Debugfs stuff is cleaned up by mmc core */
2406
2407 set_bit(ATMCI_SHUTDOWN, &slot->flags);
2408 smp_wmb();
2409
2410 mmc_remove_host(slot->mmc);
2411
2412 if (gpio_is_valid(slot->detect_pin)) {
2413 int pin = slot->detect_pin;
2414
2415 free_irq(gpio_to_irq(pin), slot);
2416 del_timer_sync(&slot->detect_timer);
2417 }
2418
2419 slot->host->slot[id] = NULL;
2420 mmc_free_host(slot->mmc);
2421}
2422
2423static int atmci_configure_dma(struct atmel_mci *host)
2424{
2425 host->dma.chan = dma_request_slave_channel_reason(&host->pdev->dev,
2426 "rxtx");
2427
2428 if (PTR_ERR(host->dma.chan) == -ENODEV) {
2429 struct mci_platform_data *pdata = host->pdev->dev.platform_data;
2430 dma_cap_mask_t mask;
2431
2432 if (!pdata || !pdata->dma_filter)
2433 return -ENODEV;
2434
2435 dma_cap_zero(mask);
2436 dma_cap_set(DMA_SLAVE, mask);
2437
2438 host->dma.chan = dma_request_channel(mask, pdata->dma_filter,
2439 pdata->dma_slave);
2440 if (!host->dma.chan)
2441 host->dma.chan = ERR_PTR(-ENODEV);
2442 }
2443
2444 if (IS_ERR(host->dma.chan))
2445 return PTR_ERR(host->dma.chan);
2446
2447 dev_info(&host->pdev->dev, "using %s for DMA transfers\n",
2448 dma_chan_name(host->dma.chan));
2449
2450 host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
2451 host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2452 host->dma_conf.src_maxburst = 1;
2453 host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
2454 host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2455 host->dma_conf.dst_maxburst = 1;
2456 host->dma_conf.device_fc = false;
2457
2458 return 0;
2459}
2460
2461/*
2462 * HSMCI (High Speed MCI) module is not fully compatible with MCI module.
2463 * HSMCI provides DMA support and a new config register but no more supports
2464 * PDC.
2465 */
2466static void atmci_get_cap(struct atmel_mci *host)
2467{
2468 unsigned int version;
2469
2470 version = atmci_get_version(host);
2471 dev_info(&host->pdev->dev,
2472 "version: 0x%x\n", version);
2473
2474 host->caps.has_dma_conf_reg = 0;
2475 host->caps.has_pdc = ATMCI_PDC_CONNECTED;
2476 host->caps.has_cfg_reg = 0;
2477 host->caps.has_cstor_reg = 0;
2478 host->caps.has_highspeed = 0;
2479 host->caps.has_rwproof = 0;
2480 host->caps.has_odd_clk_div = 0;
2481 host->caps.has_bad_data_ordering = 1;
2482 host->caps.need_reset_after_xfer = 1;
2483 host->caps.need_blksz_mul_4 = 1;
2484 host->caps.need_notbusy_for_read_ops = 0;
2485
2486 /* keep only major version number */
2487 switch (version & 0xf00) {
2488 case 0x600:
2489 case 0x500:
2490 host->caps.has_odd_clk_div = 1;
2491 case 0x400:
2492 case 0x300:
2493 host->caps.has_dma_conf_reg = 1;
2494 host->caps.has_pdc = 0;
2495 host->caps.has_cfg_reg = 1;
2496 host->caps.has_cstor_reg = 1;
2497 host->caps.has_highspeed = 1;
2498 case 0x200:
2499 host->caps.has_rwproof = 1;
2500 host->caps.need_blksz_mul_4 = 0;
2501 host->caps.need_notbusy_for_read_ops = 1;
2502 case 0x100:
2503 host->caps.has_bad_data_ordering = 0;
2504 host->caps.need_reset_after_xfer = 0;
2505 case 0x0:
2506 break;
2507 default:
2508 host->caps.has_pdc = 0;
2509 dev_warn(&host->pdev->dev,
2510 "Unmanaged mci version, set minimum capabilities\n");
2511 break;
2512 }
2513}
2514
2515static int atmci_probe(struct platform_device *pdev)
2516{
2517 struct mci_platform_data *pdata;
2518 struct atmel_mci *host;
2519 struct resource *regs;
2520 unsigned int nr_slots;
2521 int irq;
2522 int ret, i;
2523
2524 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2525 if (!regs)
2526 return -ENXIO;
2527 pdata = pdev->dev.platform_data;
2528 if (!pdata) {
2529 pdata = atmci_of_init(pdev);
2530 if (IS_ERR(pdata)) {
2531 dev_err(&pdev->dev, "platform data not available\n");
2532 return PTR_ERR(pdata);
2533 }
2534 }
2535
2536 irq = platform_get_irq(pdev, 0);
2537 if (irq < 0)
2538 return irq;
2539
2540 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
2541 if (!host)
2542 return -ENOMEM;
2543
2544 host->pdev = pdev;
2545 spin_lock_init(&host->lock);
2546 INIT_LIST_HEAD(&host->queue);
2547
2548 host->mck = devm_clk_get(&pdev->dev, "mci_clk");
2549 if (IS_ERR(host->mck))
2550 return PTR_ERR(host->mck);
2551
2552 host->regs = devm_ioremap(&pdev->dev, regs->start, resource_size(regs));
2553 if (!host->regs)
2554 return -ENOMEM;
2555
2556 ret = clk_prepare_enable(host->mck);
2557 if (ret)
2558 return ret;
2559
2560 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
2561 host->bus_hz = clk_get_rate(host->mck);
2562
2563 host->mapbase = regs->start;
2564
2565 tasklet_init(&host->tasklet, atmci_tasklet_func, (unsigned long)host);
2566
2567 ret = request_irq(irq, atmci_interrupt, 0, dev_name(&pdev->dev), host);
2568 if (ret) {
2569 clk_disable_unprepare(host->mck);
2570 return ret;
2571 }
2572
2573 /* Get MCI capabilities and set operations according to it */
2574 atmci_get_cap(host);
2575 ret = atmci_configure_dma(host);
2576 if (ret == -EPROBE_DEFER)
2577 goto err_dma_probe_defer;
2578 if (ret == 0) {
2579 host->prepare_data = &atmci_prepare_data_dma;
2580 host->submit_data = &atmci_submit_data_dma;
2581 host->stop_transfer = &atmci_stop_transfer_dma;
2582 } else if (host->caps.has_pdc) {
2583 dev_info(&pdev->dev, "using PDC\n");
2584 host->prepare_data = &atmci_prepare_data_pdc;
2585 host->submit_data = &atmci_submit_data_pdc;
2586 host->stop_transfer = &atmci_stop_transfer_pdc;
2587 } else {
2588 dev_info(&pdev->dev, "using PIO\n");
2589 host->prepare_data = &atmci_prepare_data;
2590 host->submit_data = &atmci_submit_data;
2591 host->stop_transfer = &atmci_stop_transfer;
2592 }
2593
2594 platform_set_drvdata(pdev, host);
2595
2596 setup_timer(&host->timer, atmci_timeout_timer, (unsigned long)host);
2597
2598 pm_runtime_get_noresume(&pdev->dev);
2599 pm_runtime_set_active(&pdev->dev);
2600 pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_DELAY);
2601 pm_runtime_use_autosuspend(&pdev->dev);
2602 pm_runtime_enable(&pdev->dev);
2603
2604 /* We need at least one slot to succeed */
2605 nr_slots = 0;
2606 ret = -ENODEV;
2607 if (pdata->slot[0].bus_width) {
2608 ret = atmci_init_slot(host, &pdata->slot[0],
2609 0, ATMCI_SDCSEL_SLOT_A, ATMCI_SDIOIRQA);
2610 if (!ret) {
2611 nr_slots++;
2612 host->buf_size = host->slot[0]->mmc->max_req_size;
2613 }
2614 }
2615 if (pdata->slot[1].bus_width) {
2616 ret = atmci_init_slot(host, &pdata->slot[1],
2617 1, ATMCI_SDCSEL_SLOT_B, ATMCI_SDIOIRQB);
2618 if (!ret) {
2619 nr_slots++;
2620 if (host->slot[1]->mmc->max_req_size > host->buf_size)
2621 host->buf_size =
2622 host->slot[1]->mmc->max_req_size;
2623 }
2624 }
2625
2626 if (!nr_slots) {
2627 dev_err(&pdev->dev, "init failed: no slot defined\n");
2628 goto err_init_slot;
2629 }
2630
2631 if (!host->caps.has_rwproof) {
2632 host->buffer = dma_alloc_coherent(&pdev->dev, host->buf_size,
2633 &host->buf_phys_addr,
2634 GFP_KERNEL);
2635 if (!host->buffer) {
2636 ret = -ENOMEM;
2637 dev_err(&pdev->dev, "buffer allocation failed\n");
2638 goto err_dma_alloc;
2639 }
2640 }
2641
2642 dev_info(&pdev->dev,
2643 "Atmel MCI controller at 0x%08lx irq %d, %u slots\n",
2644 host->mapbase, irq, nr_slots);
2645
2646 pm_runtime_mark_last_busy(&host->pdev->dev);
2647 pm_runtime_put_autosuspend(&pdev->dev);
2648
2649 return 0;
2650
2651err_dma_alloc:
2652 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2653 if (host->slot[i])
2654 atmci_cleanup_slot(host->slot[i], i);
2655 }
2656err_init_slot:
2657 clk_disable_unprepare(host->mck);
2658
2659 pm_runtime_disable(&pdev->dev);
2660 pm_runtime_put_noidle(&pdev->dev);
2661
2662 del_timer_sync(&host->timer);
2663 if (!IS_ERR(host->dma.chan))
2664 dma_release_channel(host->dma.chan);
2665err_dma_probe_defer:
2666 free_irq(irq, host);
2667 return ret;
2668}
2669
2670static int atmci_remove(struct platform_device *pdev)
2671{
2672 struct atmel_mci *host = platform_get_drvdata(pdev);
2673 unsigned int i;
2674
2675 pm_runtime_get_sync(&pdev->dev);
2676
2677 if (host->buffer)
2678 dma_free_coherent(&pdev->dev, host->buf_size,
2679 host->buffer, host->buf_phys_addr);
2680
2681 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2682 if (host->slot[i])
2683 atmci_cleanup_slot(host->slot[i], i);
2684 }
2685
2686 atmci_writel(host, ATMCI_IDR, ~0UL);
2687 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
2688 atmci_readl(host, ATMCI_SR);
2689
2690 del_timer_sync(&host->timer);
2691 if (!IS_ERR(host->dma.chan))
2692 dma_release_channel(host->dma.chan);
2693
2694 free_irq(platform_get_irq(pdev, 0), host);
2695
2696 clk_disable_unprepare(host->mck);
2697
2698 pm_runtime_disable(&pdev->dev);
2699 pm_runtime_put_noidle(&pdev->dev);
2700
2701 return 0;
2702}
2703
2704#ifdef CONFIG_PM
2705static int atmci_runtime_suspend(struct device *dev)
2706{
2707 struct atmel_mci *host = dev_get_drvdata(dev);
2708
2709 clk_disable_unprepare(host->mck);
2710
2711 pinctrl_pm_select_sleep_state(dev);
2712
2713 return 0;
2714}
2715
2716static int atmci_runtime_resume(struct device *dev)
2717{
2718 struct atmel_mci *host = dev_get_drvdata(dev);
2719
2720 pinctrl_pm_select_default_state(dev);
2721
2722 return clk_prepare_enable(host->mck);
2723}
2724#endif
2725
2726static const struct dev_pm_ops atmci_dev_pm_ops = {
2727 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
2728 pm_runtime_force_resume)
2729 SET_RUNTIME_PM_OPS(atmci_runtime_suspend, atmci_runtime_resume, NULL)
2730};
2731
2732static struct platform_driver atmci_driver = {
2733 .probe = atmci_probe,
2734 .remove = atmci_remove,
2735 .driver = {
2736 .name = "atmel_mci",
2737 .of_match_table = of_match_ptr(atmci_dt_ids),
2738 .pm = &atmci_dev_pm_ops,
2739 },
2740};
2741module_platform_driver(atmci_driver);
2742
2743MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver");
2744MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
2745MODULE_LICENSE("GPL v2");