Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2011 ST-Ericsson AB
4 */
5
6/dts-v1/;
7#include "ste-db9500.dtsi"
8#include "ste-href-ab8500.dtsi"
9#include "ste-href-family-pinctrl.dtsi"
10
11/ {
12 model = "Calao Systems Snowball platform with device tree";
13 compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
14
15 memory {
16 device_type = "memory";
17 reg = <0x00000000 0x20000000>;
18 };
19
20 battery: battery {
21 compatible = "simple-battery";
22 battery-type = "lithium-ion-polymer";
23 };
24
25 thermal-zones {
26 battery-thermal {
27 /* This zone will be polled by the battery temperature code */
28 polling-delay = <0>;
29 polling-delay-passive = <0>;
30 thermal-sensors = <&bat_therm>;
31
32 trips {
33 battery-crit-hi {
34 temperature = <70000>;
35 hysteresis = <2000>;
36 type = "critical";
37 };
38 };
39 };
40 };
41
42 bat_therm: thermistor {
43 compatible = "murata,ncp18wb473";
44 io-channels = <&gpadc 0x02>; /* BatTemp */
45 pullup-uv = <1800000>;
46 pullup-ohm = <230000>;
47 pulldown-ohm = <0>;
48 #thermal-sensor-cells = <0>;
49 };
50
51 en_3v3_reg: en_3v3 {
52 compatible = "regulator-fixed";
53 regulator-name = "en-3v3-fixed-supply";
54 regulator-min-microvolt = <3300000>;
55 regulator-max-microvolt = <3300000>;
56 /* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
57 gpio = <&ab8500_gpio 25 0x4>;
58 startup-delay-us = <5000>;
59 enable-active-high;
60 };
61
62 gpio_keys {
63 compatible = "gpio-keys";
64 #address-cells = <1>;
65 #size-cells = <0>;
66
67 button@1 {
68 debounce-interval = <50>;
69 wakeup-source;
70 linux,code = <2>;
71 label = "userpb";
72 gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
73 };
74 button@2 {
75 debounce-interval = <50>;
76 wakeup-source;
77 linux,code = <3>;
78 label = "extkb1";
79 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
80 };
81 button@3 {
82 debounce-interval = <50>;
83 wakeup-source;
84 linux,code = <4>;
85 label = "extkb2";
86 gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
87 };
88 button@4 {
89 debounce-interval = <50>;
90 wakeup-source;
91 linux,code = <5>;
92 label = "extkb3";
93 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
94 };
95 button@5 {
96 debounce-interval = <50>;
97 wakeup-source;
98 linux,code = <6>;
99 label = "extkb4";
100 gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
101 };
102 };
103
104 leds {
105 compatible = "gpio-leds";
106 pinctrl-names = "default";
107 pinctrl-0 = <&gpioled_snowball_mode>;
108 used-led {
109 label = "user_led";
110 gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
111 default-state = "on";
112 linux,default-trigger = "heartbeat";
113 };
114 };
115
116 soc {
117 /* Name the GPIO muxed rails on the Snowball board */
118 gpio@8012e000 {
119 /* GPIOs 0 - 31 */
120 gpio-line-names = "", "", "", "", "", "", "", "",
121 "", "", "", "", "", "", "", "",
122 "", "", "", "", "", "", "", "",
123 "", "", "", "", "", "", "",
124 "AP_GPIO31";
125 };
126
127 gpio@8012e080 {
128 /* GPIOs 32 - 63 */
129 gpio-line-names = "USR PB", "", "", "", "", "", "", "",
130 "", "", "", "", "", "", "", "",
131 "", "", "", "", "", "", "", "",
132 "", "", "", "", "", "", "", "";
133 };
134
135 gpio@8000e000 {
136 /* GPIOs 64 - 95 */
137 gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "",
138 "", "", "", "", "", "", "", "",
139 "", "", "", "", "", "", "", "",
140 "", "", "", "", "", "", "", "";
141 };
142
143 gpio@8000e100 {
144 /* GPIOs 128 - 159 */
145 gpio-line-names = "", "", "", "", "", "", "", "",
146 "", "", "", "", "IRQ_LAN", "RSTn_LAN",
147 "USR_LED", "", "", "", "", "", "",
148 "", "", "AP_GPIO151", "AP_GPIO152",
149 "", "", "", "", "", "", "";
150 };
151
152 gpio@8000e180 {
153 /* GPIOs 160 - 191 */
154 gpio-line-names = "", "AP_GPIO161", "AP_GPIO162",
155 "ACCELEROMETER_INT1_RDY",
156 "ACCELEROMETER_INT2", "MAG_DRDY",
157 "GYRO_DRDY", "RSTn_MLC", "RSTn_SLC",
158 "GYRO_INT", "UART_WAKE", "GBF_RESET",
159 "", "", "", "",
160 "", "", "", "", "", "", "", "",
161 "", "", "", "", "", "", "", "";
162 };
163
164 gpio@8011e000 {
165 /* GPIOs 192 - 223 */
166 gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST",
167 "", "", "", "", "", "", "", "", "",
168 "", "", "", "", "", "", "", "", "",
169 "WLAN_RESETN", "WLAN_IRQ", "MMC_EN",
170 "MMC_CD", "", "", "", "", "";
171 };
172
173 gpio@8011e080 {
174 /* GPIOs 224 - 255 */
175 gpio-line-names = "", "", "", "", "SD_SEL", "", "", "",
176 "", "", "", "", "", "", "", "",
177 "", "", "", "", "", "", "", "",
178 "", "", "", "", "", "", "", "";
179 };
180
181 msp0: msp@80123000 {
182 pinctrl-names = "default";
183 pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
184 status = "okay";
185 };
186
187 msp1: msp@80124000 {
188 pinctrl-names = "default";
189 pinctrl-0 = <&msp1txrx_a_1_default>;
190 status = "okay";
191 };
192
193 msp2: msp@80117000 {
194 pinctrl-names = "default";
195 pinctrl-0 = <&msp2_a_1_default>;
196 };
197
198 msp3: msp@80125000 {
199 status = "okay";
200 };
201
202 external-bus@50000000 {
203 status = "okay";
204
205 ethernet@0 {
206 compatible = "smsc,lan9115";
207 reg = <0 0x10000>;
208 interrupts = <12 IRQ_TYPE_EDGE_RISING>;
209 interrupt-parent = <&gpio4>;
210 vdd33a-supply = <&en_3v3_reg>;
211 vddvario-supply = <&db8500_vape_reg>;
212 pinctrl-names = "default";
213 pinctrl-0 = <ð_snowball_mode>;
214
215 reg-shift = <1>;
216 reg-io-width = <2>;
217 smsc,force-internal-phy;
218 smsc,irq-active-high;
219 smsc,irq-push-pull;
220
221 clocks = <&prcc_pclk 3 0>;
222 };
223 };
224
225 /* ST6G3244ME level translator for 1.8/2.9 V */
226 vmmci: regulator-gpio {
227 compatible = "regulator-gpio";
228
229 /* GPIO228 SD_SEL */
230 gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
231 /* GPIO217 MMC_EN */
232 enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
233 enable-active-high;
234
235 regulator-min-microvolt = <1800000>;
236 regulator-max-microvolt = <2900000>;
237 regulator-name = "mmci-reg";
238 regulator-type = "voltage";
239
240 startup-delay-us = <100>;
241
242 states = <1800000 0x1
243 2900000 0x0>;
244 };
245
246 // External Micro SD slot
247 mmc@80126000 {
248 arm,primecell-periphid = <0x10480180>;
249 max-frequency = <100000000>;
250 bus-width = <4>;
251 cap-sd-highspeed;
252 cap-mmc-highspeed;
253 sd-uhs-sdr12;
254 sd-uhs-sdr25;
255 /* All direction control is used */
256 st,sig-dir-cmd;
257 st,sig-dir-dat0;
258 st,sig-dir-dat2;
259 st,sig-dir-dat31;
260 st,sig-pin-fbclk;
261 full-pwr-cycle;
262 vmmc-supply = <&ab8500_ldo_aux3_reg>;
263 vqmmc-supply = <&vmmci>;
264 pinctrl-names = "default", "sleep";
265 pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
266 pinctrl-1 = <&mc0_a_1_sleep>;
267
268 /* GPIO218 MMC_CD */
269 cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
270
271 status = "okay";
272 };
273
274 // WLAN SDIO channel
275 mmc@80118000 {
276 arm,primecell-periphid = <0x10480180>;
277 max-frequency = <100000000>;
278 bus-width = <4>;
279 pinctrl-names = "default", "sleep";
280 pinctrl-0 = <&mc1_a_1_default>;
281 pinctrl-1 = <&mc1_a_1_sleep>;
282
283 status = "okay";
284 };
285
286 // Unused PoP eMMC - register and put it to sleep by default */
287 mmc@80005000 {
288 arm,primecell-periphid = <0x10480180>;
289 pinctrl-names = "default";
290 pinctrl-0 = <&mc2_a_1_sleep>;
291
292 status = "okay";
293 };
294
295 // On-board eMMC
296 mmc@80114000 {
297 arm,primecell-periphid = <0x10480180>;
298 max-frequency = <100000000>;
299 bus-width = <8>;
300 cap-mmc-highspeed;
301 no-sdio;
302 no-sd;
303 vmmc-supply = <&ab8500_ldo_aux2_reg>;
304 pinctrl-names = "default", "sleep";
305 pinctrl-0 = <&mc4_a_1_default>;
306 pinctrl-1 = <&mc4_a_1_sleep>;
307
308 status = "okay";
309 };
310
311 uart@80120000 {
312 pinctrl-names = "default", "sleep";
313 pinctrl-0 = <&u0_a_1_default>;
314 pinctrl-1 = <&u0_a_1_sleep>;
315 status = "okay";
316 };
317
318 /* This UART is unused and thus left disabled */
319 uart@80121000 {
320 pinctrl-names = "default", "sleep";
321 pinctrl-0 = <&u1rxtx_a_1_default>;
322 pinctrl-1 = <&u1rxtx_a_1_sleep>;
323 };
324
325 uart@80007000 {
326 pinctrl-names = "default", "sleep";
327 pinctrl-0 = <&u2rxtx_c_1_default>;
328 pinctrl-1 = <&u2rxtx_c_1_sleep>;
329 status = "okay";
330 };
331
332 i2c@80004000 {
333 pinctrl-names = "default","sleep";
334 pinctrl-0 = <&i2c0_a_1_default>;
335 pinctrl-1 = <&i2c0_a_1_sleep>;
336 status = "okay";
337 };
338
339 i2c@80122000 {
340 pinctrl-names = "default","sleep";
341 pinctrl-0 = <&i2c1_b_2_default>;
342 pinctrl-1 = <&i2c1_b_2_sleep>;
343 status = "okay";
344 };
345
346 i2c@80128000 {
347 pinctrl-names = "default","sleep";
348 pinctrl-0 = <&i2c2_b_2_default>;
349 pinctrl-1 = <&i2c2_b_2_sleep>;
350 status = "okay";
351 lsm303dlh@18 {
352 /* Accelerometer */
353 compatible = "st,lsm303dlh-accel";
354 st,drdy-int-pin = <1>;
355 reg = <0x18>;
356 vdd-supply = <&ab8500_ldo_aux1_reg>;
357 vddio-supply = <&db8500_vsmps2_reg>;
358 pinctrl-names = "default";
359 pinctrl-0 = <&accel_snowball_mode>;
360 interrupt-parent = <&gpio5>;
361 interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
362 <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
363 };
364 lsm303dlh@1e {
365 /* Magnetometer */
366 compatible = "st,lsm303dlh-magn";
367 reg = <0x1e>;
368 vdd-supply = <&ab8500_ldo_aux1_reg>;
369 vddio-supply = <&db8500_vsmps2_reg>;
370 pinctrl-names = "default";
371 pinctrl-0 = <&magneto_snowball_mode>;
372 interrupt-parent = <&gpio5>;
373 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
374 };
375 l3g4200d@68 {
376 /* Gyroscope */
377 compatible = "st,l3g4200d-gyro";
378 st,drdy-int-pin = <2>;
379 reg = <0x68>;
380 vdd-supply = <&ab8500_ldo_aux1_reg>;
381 vddio-supply = <&db8500_vsmps2_reg>;
382 pinctrl-names = "default";
383 pinctrl-0 = <&gyro_snowball_mode>;
384 interrupt-parent = <&gpio5>;
385 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
386 <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
387 };
388 lsp001wm@5c {
389 /* Barometer/pressure sensor */
390 compatible = "st,lps001wp-press";
391 reg = <0x5c>;
392 vdd-supply = <&ab8500_ldo_aux1_reg>;
393 vddio-supply = <&db8500_vsmps2_reg>;
394 };
395 };
396
397 i2c@80110000 {
398 pinctrl-names = "default","sleep";
399 pinctrl-0 = <&i2c3_c_2_default>;
400 pinctrl-1 = <&i2c3_c_2_sleep>;
401 status = "okay";
402 };
403
404 spi@80002000 {
405 pinctrl-names = "default";
406 pinctrl-0 = <&ssp0_snowball_mode>;
407 status = "okay";
408 };
409
410 prcmu@80157000 {
411 ab8500 {
412 gpio {
413 /*
414 * AB8500 GPIOs are numbered starting from 1, so the first
415 * index 0 is what in the datasheet is called "GPIO1", and
416 * the second is "GPIO2" and so forth. Confusingly, the
417 * Snowball schematic then names the "GPIO2" line "PM_GPIO1".
418 * while later naming "GPIO4" as "PM_GPIO4".
419 */
420 gpio-line-names = "", /* AB8500 GPIO1 */
421 "PM_GPIO1", /* AB8500 GPIO2 */
422 "WLAN_CLK_REQ", /* AB8500 GPIO3 */
423 "PM_GPIO4", /* AB8500 GPIO4 */
424 "", "", "", "", "", "", "", "", "", "", "",
425 "EN_3V6", /* AB8500 GPIO16 */
426 "", "", "", "" ,"", "", "", "", "",
427 "EN_3V3", /* AB8500 GPIO26 */
428 "", "", "", "", "", "", "", "", "", "", "", "", "",
429 "PM_GPIO40", /* AB8500 GPIO40 */
430 "PM_GPIO41", /* AB8500 GPIO41 */
431 "PM_GPIO42"; /* AB8500 GPIO42 */
432 };
433
434 phy {
435 pinctrl-names = "default", "sleep";
436 pinctrl-0 = <&usb_a_1_default>;
437 pinctrl-1 = <&usb_a_1_sleep>;
438 };
439
440 ext_regulators: regulator-external {
441 ab8500_ext1_reg: ab8500_ext1 {
442 regulator-name = "ab8500-ext-supply1";
443 };
444
445 ab8500_ext2_reg_reg: ab8500_ext2 {
446 regulator-name = "ab8500-ext-supply2";
447 };
448
449 ab8500_ext3_reg_reg: ab8500_ext3 {
450 regulator-name = "ab8500-ext-supply3";
451 };
452 };
453
454 regulator {
455 ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
456 regulator-name = "V-DISPLAY";
457 };
458
459 ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
460 regulator-name = "V-eMMC1";
461 };
462
463 ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
464 regulator-name = "V-MMC-SD";
465 };
466
467 ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
468 regulator-name = "V-INTCORE";
469 };
470
471 ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
472 regulator-name = "V-TVOUT";
473 };
474
475 ab8500_ldo_audio_reg: ab8500_ldo_audio {
476 regulator-name = "V-AUD";
477 };
478
479 ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
480 regulator-name = "V-AMIC1";
481 };
482
483 ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
484 regulator-name = "V-AMIC2";
485 };
486
487 ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
488 regulator-name = "V-DMIC";
489 };
490
491 ab8500_ldo_ana_reg: ab8500_ldo_ana {
492 regulator-name = "V-CSI/DSI";
493 };
494 };
495 };
496 };
497
498 pinctrl {
499 /*
500 * Set this up using hogs, as time goes by and as seems fit, these
501 * can be moved over to being controlled by respective device.
502 */
503 pinctrl-names = "default";
504 pinctrl-0 = <&gbf_snowball_mode>,
505 <&wlan_snowball_mode>;
506
507 ethernet {
508 /*
509 * Mux in "SM" which is used for the
510 * SMSC911x Ethernet adapter
511 */
512 eth_snowball_mode: eth_snowball {
513 snowball_mux {
514 function = "sm";
515 groups = "sm_b_1";
516 };
517 /* LAN IRQ pin */
518 snowball_cfg1 {
519 pins = "GPIO140_B11";
520 ste,config = <&in_nopull>;
521 };
522 /* LAN reset pin */
523 snowball_cfg2 {
524 pins = "GPIO141_C12";
525 ste,config = <&gpio_out_hi>;
526 };
527
528 };
529 };
530 sdi0 {
531 sdi0_default_mode: sdi0_default {
532 snowball_mux {
533 function = "mc0";
534 /* Add the DAT31 pin even if it is not really used */
535 groups = "mc0dat31dir_a_1";
536 };
537 snowball_cfg1 {
538 pins = "GPIO21_AB3"; /* DAT31DIR */
539 ste,config = <&out_hi>;
540 };
541 /* SD card detect GPIO pin, extend default state */
542 snowball_cfg2 {
543 pins = "GPIO218_AH11";
544 ste,config = <&gpio_in_pu>;
545 };
546 /* VMMCI level-shifter enable */
547 snowball_cfg3 {
548 pins = "GPIO217_AH12";
549 ste,config = <&gpio_out_hi>;
550 };
551 /* VMMCI level-shifter voltage select */
552 snowball_cfg4 {
553 pins = "GPIO228_AJ6";
554 ste,config = <&gpio_out_hi>;
555 };
556 };
557 };
558 ssp0 {
559 ssp0_snowball_mode: ssp0_snowball_default {
560 snowball_mux {
561 function = "ssp0";
562 groups = "ssp0_a_1";
563 };
564 snowball_cfg1 {
565 pins = "GPIO144_B13"; /* FRM */
566 ste,config = <&gpio_out_hi>;
567 };
568 snowball_cfg2 {
569 pins = "GPIO145_C13"; /* RXD */
570 ste,config = <&in_pd>;
571 };
572 snowball_cfg3 {
573 pins =
574 "GPIO146_D13", /* TXD */
575 "GPIO143_D12"; /* CLK */
576 ste,config = <&out_lo>;
577 };
578
579 };
580 };
581 gpio_led {
582 gpioled_snowball_mode: gpioled_default {
583 snowball_cfg1 {
584 pins = "GPIO142_C11";
585 ste,config = <&gpio_out_hi>;
586 };
587
588 };
589 };
590 accelerometer {
591 accel_snowball_mode: accel_snowball {
592 /* Accelerometer lines */
593 snowball_cfg1 {
594 pins =
595 "GPIO163_C20", /* ACCEL_IRQ1 */
596 "GPIO164_B21"; /* ACCEL_IRQ2 */
597 ste,config = <&gpio_in_pu>;
598 };
599 };
600 };
601 gyro {
602 gyro_snowball_mode: gyro_snowball {
603 snowball_cfg1 {
604 pins =
605 "GPIO166_A22", /* DRDY */
606 "GPIO169_D22"; /* INT */
607 ste,config = <&gpio_in_pu>;
608 };
609 };
610 };
611 magnetometer {
612 magneto_snowball_mode: magneto_snowball {
613 snowball_cfg1 {
614 pins = "GPIO165_C21"; /* MAG_DRDY */
615 ste,config = <&gpio_in_pu>;
616 };
617 };
618 };
619 gbf {
620 gbf_snowball_mode: gbf_snowball {
621 /*
622 * GBF (GPS, Bluetooth, FM-radio) interface,
623 * pull low to reset state
624 */
625 snowball_cfg1 {
626 pins = "GPIO171_D23"; /* GBF_ENA_RESET */
627 ste,config = <&gpio_out_lo>;
628 };
629 };
630 };
631 wlan {
632 wlan_snowball_mode: wlan_snowball {
633 /*
634 * Activate this mode with the WLAN chip.
635 * These are plain GPIO pins used by WLAN
636 */
637 snowball_cfg1 {
638 pins =
639 "GPIO161_D21", /* WLAN_PMU_EN */
640 "GPIO215_AH13"; /* WLAN_ENA */
641 ste,config = <&gpio_out_lo>;
642 };
643 snowball_cfg2 {
644 pins = "GPIO216_AG12"; /* WLAN_IRQ */
645 ste,config = <&gpio_in_pu>;
646 };
647 };
648 };
649 };
650
651 mcde@a0350000 {
652 pinctrl-names = "default", "sleep";
653 pinctrl-0 = <&lcd_default_mode>;
654 pinctrl-1 = <&lcd_sleep_mode>;
655 };
656 };
657};
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2011 ST-Ericsson AB
4 */
5
6/dts-v1/;
7#include "ste-db8500.dtsi"
8#include "ste-href-ab8500.dtsi"
9#include "ste-href-family-pinctrl.dtsi"
10
11/ {
12 model = "Calao Systems Snowball platform with device tree";
13 compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
14
15 memory {
16 device_type = "memory";
17 reg = <0x00000000 0x20000000>;
18 };
19
20 en_3v3_reg: en_3v3 {
21 compatible = "regulator-fixed";
22 regulator-name = "en-3v3-fixed-supply";
23 regulator-min-microvolt = <3300000>;
24 regulator-max-microvolt = <3300000>;
25 /* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
26 gpio = <&ab8500_gpio 25 0x4>;
27 startup-delay-us = <5000>;
28 enable-active-high;
29 };
30
31 gpio_keys {
32 compatible = "gpio-keys";
33 #address-cells = <1>;
34 #size-cells = <0>;
35
36 button@1 {
37 debounce-interval = <50>;
38 wakeup-source;
39 linux,code = <2>;
40 label = "userpb";
41 gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
42 };
43 button@2 {
44 debounce-interval = <50>;
45 wakeup-source;
46 linux,code = <3>;
47 label = "extkb1";
48 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
49 };
50 button@3 {
51 debounce-interval = <50>;
52 wakeup-source;
53 linux,code = <4>;
54 label = "extkb2";
55 gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
56 };
57 button@4 {
58 debounce-interval = <50>;
59 wakeup-source;
60 linux,code = <5>;
61 label = "extkb3";
62 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
63 };
64 button@5 {
65 debounce-interval = <50>;
66 wakeup-source;
67 linux,code = <6>;
68 label = "extkb4";
69 gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
70 };
71 };
72
73 leds {
74 compatible = "gpio-leds";
75 pinctrl-names = "default";
76 pinctrl-0 = <&gpioled_snowball_mode>;
77 used-led {
78 label = "user_led";
79 gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
80 default-state = "on";
81 linux,default-trigger = "heartbeat";
82 };
83 };
84
85 soc {
86 /* Name the GPIO muxed rails on the Snowball board */
87 gpio@8012e000 {
88 /* GPIOs 0 - 31 */
89 gpio-line-names = "", "", "", "", "", "", "", "",
90 "", "", "", "", "", "", "", "",
91 "", "", "", "", "", "", "", "",
92 "", "", "", "", "", "", "",
93 "AP_GPIO31";
94 };
95
96 gpio@8012e080 {
97 /* GPIOs 32 - 63 */
98 gpio-line-names = "USR PB", "", "", "", "", "", "", "",
99 "", "", "", "", "", "", "", "",
100 "", "", "", "", "", "", "", "",
101 "", "", "", "", "", "", "", "";
102 };
103
104 gpio@8000e000 {
105 /* GPIOs 64 - 95 */
106 gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "",
107 "", "", "", "", "", "", "", "",
108 "", "", "", "", "", "", "", "",
109 "", "", "", "", "", "", "", "";
110 };
111
112 gpio@8000e100 {
113 /* GPIOs 128 - 159 */
114 gpio-line-names = "", "", "", "", "", "", "", "",
115 "", "", "", "", "IRQ_LAN", "RSTn_LAN",
116 "USR_LED", "", "", "", "", "", "",
117 "", "", "AP_GPIO151", "AP_GPIO152",
118 "", "", "", "", "", "", "";
119 };
120
121 gpio@8000e180 {
122 /* GPIOs 160 - 191 */
123 gpio-line-names = "", "AP_GPIO161", "AP_GPIO162",
124 "ACCELEROMETER_INT1_RDY",
125 "ACCELEROMETER_INT2", "MAG_DRDY",
126 "GYRO_DRDY", "RSTn_MLC", "RSTn_SLC",
127 "GYRO_INT", "UART_WAKE", "GBF_RESET",
128 "", "", "", "",
129 "", "", "", "", "", "", "", "",
130 "", "", "", "", "", "", "", "";
131 };
132
133 gpio@8011e000 {
134 /* GPIOs 192 - 223 */
135 gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST",
136 "", "", "", "", "", "", "", "", "",
137 "", "", "", "", "", "", "", "", "",
138 "WLAN_RESETN", "WLAN_IRQ", "MMC_EN",
139 "MMC_CD", "", "", "", "", "";
140 };
141
142 gpio@8011e080 {
143 /* GPIOs 224 - 255 */
144 gpio-line-names = "", "", "", "", "SD_SEL", "", "", "",
145 "", "", "", "", "", "", "", "",
146 "", "", "", "", "", "", "", "",
147 "", "", "", "", "", "", "", "";
148 };
149
150 msp0: msp@80123000 {
151 pinctrl-names = "default";
152 pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
153 status = "okay";
154 };
155
156 msp1: msp@80124000 {
157 pinctrl-names = "default";
158 pinctrl-0 = <&msp1txrx_a_1_default>;
159 status = "okay";
160 };
161
162 msp2: msp@80117000 {
163 pinctrl-names = "default";
164 pinctrl-0 = <&msp2_a_1_default>;
165 };
166
167 msp3: msp@80125000 {
168 status = "okay";
169 };
170
171 external-bus@50000000 {
172 status = "okay";
173
174 ethernet@0 {
175 compatible = "smsc,lan9115";
176 reg = <0 0x10000>;
177 interrupts = <12 IRQ_TYPE_EDGE_RISING>;
178 interrupt-parent = <&gpio4>;
179 vdd33a-supply = <&en_3v3_reg>;
180 vddvario-supply = <&db8500_vape_reg>;
181 pinctrl-names = "default";
182 pinctrl-0 = <ð_snowball_mode>;
183
184 reg-shift = <1>;
185 reg-io-width = <2>;
186 smsc,force-internal-phy;
187 smsc,irq-active-high;
188 smsc,irq-push-pull;
189
190 clocks = <&prcc_pclk 3 0>;
191 };
192 };
193
194 /* ST6G3244ME level translator for 1.8/2.9 V */
195 vmmci: regulator-gpio {
196 compatible = "regulator-gpio";
197
198 /* GPIO228 SD_SEL */
199 gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
200 /* GPIO217 MMC_EN */
201 enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
202 enable-active-high;
203
204 regulator-min-microvolt = <1800000>;
205 regulator-max-microvolt = <2900000>;
206 regulator-name = "mmci-reg";
207 regulator-type = "voltage";
208
209 startup-delay-us = <100>;
210
211 states = <1800000 0x1
212 2900000 0x0>;
213 };
214
215 // External Micro SD slot
216 sdi0_per1@80126000 {
217 arm,primecell-periphid = <0x10480180>;
218 max-frequency = <100000000>;
219 bus-width = <4>;
220 cap-sd-highspeed;
221 cap-mmc-highspeed;
222 sd-uhs-sdr12;
223 sd-uhs-sdr25;
224 /* All direction control is used */
225 st,sig-dir-cmd;
226 st,sig-dir-dat0;
227 st,sig-dir-dat2;
228 st,sig-dir-dat31;
229 st,sig-pin-fbclk;
230 full-pwr-cycle;
231 vmmc-supply = <&ab8500_ldo_aux3_reg>;
232 vqmmc-supply = <&vmmci>;
233 pinctrl-names = "default", "sleep";
234 pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
235 pinctrl-1 = <&mc0_a_1_sleep>;
236
237 /* GPIO218 MMC_CD */
238 cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
239
240 status = "okay";
241 };
242
243 // WLAN SDIO channel
244 sdi1_per2@80118000 {
245 arm,primecell-periphid = <0x10480180>;
246 max-frequency = <100000000>;
247 bus-width = <4>;
248 pinctrl-names = "default", "sleep";
249 pinctrl-0 = <&mc1_a_1_default>;
250 pinctrl-1 = <&mc1_a_1_sleep>;
251
252 status = "okay";
253 };
254
255 // Unused PoP eMMC - register and put it to sleep by default */
256 sdi2_per3@80005000 {
257 arm,primecell-periphid = <0x10480180>;
258 pinctrl-names = "default";
259 pinctrl-0 = <&mc2_a_1_sleep>;
260
261 status = "okay";
262 };
263
264 // On-board eMMC
265 sdi4_per2@80114000 {
266 arm,primecell-periphid = <0x10480180>;
267 max-frequency = <100000000>;
268 bus-width = <8>;
269 cap-mmc-highspeed;
270 vmmc-supply = <&ab8500_ldo_aux2_reg>;
271 pinctrl-names = "default", "sleep";
272 pinctrl-0 = <&mc4_a_1_default>;
273 pinctrl-1 = <&mc4_a_1_sleep>;
274
275 status = "okay";
276 };
277
278 uart@80120000 {
279 pinctrl-names = "default", "sleep";
280 pinctrl-0 = <&u0_a_1_default>;
281 pinctrl-1 = <&u0_a_1_sleep>;
282 status = "okay";
283 };
284
285 /* This UART is unused and thus left disabled */
286 uart@80121000 {
287 pinctrl-names = "default", "sleep";
288 pinctrl-0 = <&u1rxtx_a_1_default>;
289 pinctrl-1 = <&u1rxtx_a_1_sleep>;
290 };
291
292 uart@80007000 {
293 pinctrl-names = "default", "sleep";
294 pinctrl-0 = <&u2rxtx_c_1_default>;
295 pinctrl-1 = <&u2rxtx_c_1_sleep>;
296 status = "okay";
297 };
298
299 i2c@80004000 {
300 pinctrl-names = "default","sleep";
301 pinctrl-0 = <&i2c0_a_1_default>;
302 pinctrl-1 = <&i2c0_a_1_sleep>;
303 status = "okay";
304 };
305
306 i2c@80122000 {
307 pinctrl-names = "default","sleep";
308 pinctrl-0 = <&i2c1_b_2_default>;
309 pinctrl-1 = <&i2c1_b_2_sleep>;
310 status = "okay";
311 };
312
313 i2c@80128000 {
314 pinctrl-names = "default","sleep";
315 pinctrl-0 = <&i2c2_b_2_default>;
316 pinctrl-1 = <&i2c2_b_2_sleep>;
317 status = "okay";
318 lsm303dlh@18 {
319 /* Accelerometer */
320 compatible = "st,lsm303dlh-accel";
321 st,drdy-int-pin = <1>;
322 reg = <0x18>;
323 vdd-supply = <&ab8500_ldo_aux1_reg>;
324 vddio-supply = <&db8500_vsmps2_reg>;
325 pinctrl-names = "default";
326 pinctrl-0 = <&accel_snowball_mode>;
327 interrupt-parent = <&gpio5>;
328 interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
329 <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
330 };
331 lsm303dlh@1e {
332 /* Magnetometer */
333 compatible = "st,lsm303dlh-magn";
334 reg = <0x1e>;
335 vdd-supply = <&ab8500_ldo_aux1_reg>;
336 vddio-supply = <&db8500_vsmps2_reg>;
337 pinctrl-names = "default";
338 pinctrl-0 = <&magneto_snowball_mode>;
339 interrupt-parent = <&gpio5>;
340 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
341 };
342 l3g4200d@68 {
343 /* Gyroscope */
344 compatible = "st,l3g4200d-gyro";
345 st,drdy-int-pin = <2>;
346 reg = <0x68>;
347 vdd-supply = <&ab8500_ldo_aux1_reg>;
348 vddio-supply = <&db8500_vsmps2_reg>;
349 pinctrl-names = "default";
350 pinctrl-0 = <&gyro_snowball_mode>;
351 interrupt-parent = <&gpio5>;
352 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
353 <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
354 };
355 lsp001wm@5c {
356 /* Barometer/pressure sensor */
357 compatible = "st,lps001wp-press";
358 reg = <0x5c>;
359 vdd-supply = <&ab8500_ldo_aux1_reg>;
360 vddio-supply = <&db8500_vsmps2_reg>;
361 };
362 };
363
364 i2c@80110000 {
365 pinctrl-names = "default","sleep";
366 pinctrl-0 = <&i2c3_c_2_default>;
367 pinctrl-1 = <&i2c3_c_2_sleep>;
368 status = "okay";
369 };
370
371 spi@80002000 {
372 pinctrl-names = "default";
373 pinctrl-0 = <&ssp0_snowball_mode>;
374 status = "okay";
375 };
376
377 prcmu@80157000 {
378 ab8500 {
379 ab8500-gpio {
380 /*
381 * AB8500 GPIOs are numbered starting from 1, so the first
382 * index 0 is what in the datasheet is called "GPIO1", and
383 * the second is "GPIO2" and so forth. Confusingly, the
384 * Snowball schematic then names the "GPIO2" line "PM_GPIO1".
385 * while later naming "GPIO4" as "PM_GPIO4".
386 */
387 gpio-line-names = "", /* AB8500 GPIO1 */
388 "PM_GPIO1", /* AB8500 GPIO2 */
389 "WLAN_CLK_REQ", /* AB8500 GPIO3 */
390 "PM_GPIO4", /* AB8500 GPIO4 */
391 "", "", "", "", "", "", "", "", "", "", "",
392 "EN_3V6", /* AB8500 GPIO16 */
393 "", "", "", "" ,"", "", "", "", "",
394 "EN_3V3", /* AB8500 GPIO26 */
395 "", "", "", "", "", "", "", "", "", "", "", "", "",
396 "PM_GPIO40", /* AB8500 GPIO40 */
397 "PM_GPIO41", /* AB8500 GPIO41 */
398 "PM_GPIO42"; /* AB8500 GPIO42 */
399 };
400
401 ab8500_usb {
402 pinctrl-names = "default", "sleep";
403 pinctrl-0 = <&usb_a_1_default>;
404 pinctrl-1 = <&usb_a_1_sleep>;
405 };
406
407 ext_regulators: ab8500-ext-regulators {
408 ab8500_ext1_reg: ab8500_ext1 {
409 regulator-name = "ab8500-ext-supply1";
410 };
411
412 ab8500_ext2_reg_reg: ab8500_ext2 {
413 regulator-name = "ab8500-ext-supply2";
414 };
415
416 ab8500_ext3_reg_reg: ab8500_ext3 {
417 regulator-name = "ab8500-ext-supply3";
418 };
419 };
420
421 ab8500-regulators {
422 ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
423 regulator-name = "V-DISPLAY";
424 };
425
426 ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
427 regulator-name = "V-eMMC1";
428 };
429
430 ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
431 regulator-name = "V-MMC-SD";
432 };
433
434 ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
435 regulator-name = "V-INTCORE";
436 };
437
438 ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
439 regulator-name = "V-TVOUT";
440 };
441
442 ab8500_ldo_audio_reg: ab8500_ldo_audio {
443 regulator-name = "V-AUD";
444 };
445
446 ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
447 regulator-name = "V-AMIC1";
448 };
449
450 ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
451 regulator-name = "V-AMIC2";
452 };
453
454 ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
455 regulator-name = "V-DMIC";
456 };
457
458 ab8500_ldo_ana_reg: ab8500_ldo_ana {
459 regulator-name = "V-CSI/DSI";
460 };
461 };
462 };
463 };
464
465 pinctrl {
466 /*
467 * Set this up using hogs, as time goes by and as seems fit, these
468 * can be moved over to being controlled by respective device.
469 */
470 pinctrl-names = "default";
471 pinctrl-0 = <&gbf_snowball_mode>,
472 <&wlan_snowball_mode>;
473
474 ethernet {
475 /*
476 * Mux in "SM" which is used for the
477 * SMSC911x Ethernet adapter
478 */
479 eth_snowball_mode: eth_snowball {
480 snowball_mux {
481 function = "sm";
482 groups = "sm_b_1";
483 };
484 /* LAN IRQ pin */
485 snowball_cfg1 {
486 pins = "GPIO140_B11";
487 ste,config = <&in_nopull>;
488 };
489 /* LAN reset pin */
490 snowball_cfg2 {
491 pins = "GPIO141_C12";
492 ste,config = <&gpio_out_hi>;
493 };
494
495 };
496 };
497 sdi0 {
498 sdi0_default_mode: sdi0_default {
499 snowball_mux {
500 function = "mc0";
501 /* Add the DAT31 pin even if it is not really used */
502 groups = "mc0dat31dir_a_1";
503 };
504 snowball_cfg1 {
505 pins = "GPIO21_AB3"; /* DAT31DIR */
506 ste,config = <&out_hi>;
507 };
508 /* SD card detect GPIO pin, extend default state */
509 snowball_cfg2 {
510 pins = "GPIO218_AH11";
511 ste,config = <&gpio_in_pu>;
512 };
513 /* VMMCI level-shifter enable */
514 snowball_cfg3 {
515 pins = "GPIO217_AH12";
516 ste,config = <&gpio_out_hi>;
517 };
518 /* VMMCI level-shifter voltage select */
519 snowball_cfg4 {
520 pins = "GPIO228_AJ6";
521 ste,config = <&gpio_out_hi>;
522 };
523 };
524 };
525 ssp0 {
526 ssp0_snowball_mode: ssp0_snowball_default {
527 snowball_mux {
528 function = "ssp0";
529 groups = "ssp0_a_1";
530 };
531 snowball_cfg1 {
532 pins = "GPIO144_B13"; /* FRM */
533 ste,config = <&gpio_out_hi>;
534 };
535 snowball_cfg2 {
536 pins = "GPIO145_C13"; /* RXD */
537 ste,config = <&in_pd>;
538 };
539 snowball_cfg3 {
540 pins =
541 "GPIO146_D13", /* TXD */
542 "GPIO143_D12"; /* CLK */
543 ste,config = <&out_lo>;
544 };
545
546 };
547 };
548 gpio_led {
549 gpioled_snowball_mode: gpioled_default {
550 snowball_cfg1 {
551 pins = "GPIO142_C11";
552 ste,config = <&gpio_out_hi>;
553 };
554
555 };
556 };
557 accelerometer {
558 accel_snowball_mode: accel_snowball {
559 /* Accelerometer lines */
560 snowball_cfg1 {
561 pins =
562 "GPIO163_C20", /* ACCEL_IRQ1 */
563 "GPIO164_B21"; /* ACCEL_IRQ2 */
564 ste,config = <&gpio_in_pu>;
565 };
566 };
567 };
568 gyro {
569 gyro_snowball_mode: gyro_snowball {
570 snowball_cfg1 {
571 pins =
572 "GPIO166_A22", /* DRDY */
573 "GPIO169_D22"; /* INT */
574 ste,config = <&gpio_in_pu>;
575 };
576 };
577 };
578 magnetometer {
579 magneto_snowball_mode: magneto_snowball {
580 snowball_cfg1 {
581 pins = "GPIO165_C21"; /* MAG_DRDY */
582 ste,config = <&gpio_in_pu>;
583 };
584 };
585 };
586 gbf {
587 gbf_snowball_mode: gbf_snowball {
588 /*
589 * GBF (GPS, Bluetooth, FM-radio) interface,
590 * pull low to reset state
591 */
592 snowball_cfg1 {
593 pins = "GPIO171_D23"; /* GBF_ENA_RESET */
594 ste,config = <&gpio_out_lo>;
595 };
596 };
597 };
598 wlan {
599 wlan_snowball_mode: wlan_snowball {
600 /*
601 * Activate this mode with the WLAN chip.
602 * These are plain GPIO pins used by WLAN
603 */
604 snowball_cfg1 {
605 pins =
606 "GPIO161_D21", /* WLAN_PMU_EN */
607 "GPIO215_AH13"; /* WLAN_ENA */
608 ste,config = <&gpio_out_lo>;
609 };
610 snowball_cfg2 {
611 pins = "GPIO216_AG12"; /* WLAN_IRQ */
612 ste,config = <&gpio_in_pu>;
613 };
614 };
615 };
616 };
617
618 mcde@a0350000 {
619 pinctrl-names = "default", "sleep";
620 pinctrl-0 = <&lcd_default_mode>;
621 pinctrl-1 = <&lcd_sleep_mode>;
622 };
623 };
624};