Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2011 ST-Ericsson AB
4 */
5
6/dts-v1/;
7#include "ste-db9500.dtsi"
8#include "ste-href-ab8500.dtsi"
9#include "ste-href-family-pinctrl.dtsi"
10
11/ {
12 model = "Calao Systems Snowball platform with device tree";
13 compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
14
15 memory {
16 device_type = "memory";
17 reg = <0x00000000 0x20000000>;
18 };
19
20 battery: battery {
21 compatible = "simple-battery";
22 battery-type = "lithium-ion-polymer";
23 };
24
25 thermal-zones {
26 battery-thermal {
27 /* This zone will be polled by the battery temperature code */
28 polling-delay = <0>;
29 polling-delay-passive = <0>;
30 thermal-sensors = <&bat_therm>;
31
32 trips {
33 battery-crit-hi {
34 temperature = <70000>;
35 hysteresis = <2000>;
36 type = "critical";
37 };
38 };
39 };
40 };
41
42 bat_therm: thermistor {
43 compatible = "murata,ncp18wb473";
44 io-channels = <&gpadc 0x02>; /* BatTemp */
45 pullup-uv = <1800000>;
46 pullup-ohm = <230000>;
47 pulldown-ohm = <0>;
48 #thermal-sensor-cells = <0>;
49 };
50
51 en_3v3_reg: en_3v3 {
52 compatible = "regulator-fixed";
53 regulator-name = "en-3v3-fixed-supply";
54 regulator-min-microvolt = <3300000>;
55 regulator-max-microvolt = <3300000>;
56 /* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
57 gpio = <&ab8500_gpio 25 0x4>;
58 startup-delay-us = <5000>;
59 enable-active-high;
60 };
61
62 gpio_keys {
63 compatible = "gpio-keys";
64 #address-cells = <1>;
65 #size-cells = <0>;
66
67 button@1 {
68 debounce-interval = <50>;
69 wakeup-source;
70 linux,code = <2>;
71 label = "userpb";
72 gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
73 };
74 button@2 {
75 debounce-interval = <50>;
76 wakeup-source;
77 linux,code = <3>;
78 label = "extkb1";
79 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
80 };
81 button@3 {
82 debounce-interval = <50>;
83 wakeup-source;
84 linux,code = <4>;
85 label = "extkb2";
86 gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
87 };
88 button@4 {
89 debounce-interval = <50>;
90 wakeup-source;
91 linux,code = <5>;
92 label = "extkb3";
93 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
94 };
95 button@5 {
96 debounce-interval = <50>;
97 wakeup-source;
98 linux,code = <6>;
99 label = "extkb4";
100 gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
101 };
102 };
103
104 leds {
105 compatible = "gpio-leds";
106 pinctrl-names = "default";
107 pinctrl-0 = <&gpioled_snowball_mode>;
108 used-led {
109 label = "user_led";
110 gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
111 default-state = "on";
112 linux,default-trigger = "heartbeat";
113 };
114 };
115
116 soc {
117 /* Name the GPIO muxed rails on the Snowball board */
118 gpio@8012e000 {
119 /* GPIOs 0 - 31 */
120 gpio-line-names = "", "", "", "", "", "", "", "",
121 "", "", "", "", "", "", "", "",
122 "", "", "", "", "", "", "", "",
123 "", "", "", "", "", "", "",
124 "AP_GPIO31";
125 };
126
127 gpio@8012e080 {
128 /* GPIOs 32 - 63 */
129 gpio-line-names = "USR PB", "", "", "", "", "", "", "",
130 "", "", "", "", "", "", "", "",
131 "", "", "", "", "", "", "", "",
132 "", "", "", "", "", "", "", "";
133 };
134
135 gpio@8000e000 {
136 /* GPIOs 64 - 95 */
137 gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "",
138 "", "", "", "", "", "", "", "",
139 "", "", "", "", "", "", "", "",
140 "", "", "", "", "", "", "", "";
141 };
142
143 gpio@8000e100 {
144 /* GPIOs 128 - 159 */
145 gpio-line-names = "", "", "", "", "", "", "", "",
146 "", "", "", "", "IRQ_LAN", "RSTn_LAN",
147 "USR_LED", "", "", "", "", "", "",
148 "", "", "AP_GPIO151", "AP_GPIO152",
149 "", "", "", "", "", "", "";
150 };
151
152 gpio@8000e180 {
153 /* GPIOs 160 - 191 */
154 gpio-line-names = "", "AP_GPIO161", "AP_GPIO162",
155 "ACCELEROMETER_INT1_RDY",
156 "ACCELEROMETER_INT2", "MAG_DRDY",
157 "GYRO_DRDY", "RSTn_MLC", "RSTn_SLC",
158 "GYRO_INT", "UART_WAKE", "GBF_RESET",
159 "", "", "", "",
160 "", "", "", "", "", "", "", "",
161 "", "", "", "", "", "", "", "";
162 };
163
164 gpio@8011e000 {
165 /* GPIOs 192 - 223 */
166 gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST",
167 "", "", "", "", "", "", "", "", "",
168 "", "", "", "", "", "", "", "", "",
169 "WLAN_RESETN", "WLAN_IRQ", "MMC_EN",
170 "MMC_CD", "", "", "", "", "";
171 };
172
173 gpio@8011e080 {
174 /* GPIOs 224 - 255 */
175 gpio-line-names = "", "", "", "", "SD_SEL", "", "", "",
176 "", "", "", "", "", "", "", "",
177 "", "", "", "", "", "", "", "",
178 "", "", "", "", "", "", "", "";
179 };
180
181 msp0: msp@80123000 {
182 pinctrl-names = "default";
183 pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
184 status = "okay";
185 };
186
187 msp1: msp@80124000 {
188 pinctrl-names = "default";
189 pinctrl-0 = <&msp1txrx_a_1_default>;
190 status = "okay";
191 };
192
193 msp2: msp@80117000 {
194 pinctrl-names = "default";
195 pinctrl-0 = <&msp2_a_1_default>;
196 };
197
198 msp3: msp@80125000 {
199 status = "okay";
200 };
201
202 external-bus@50000000 {
203 status = "okay";
204
205 ethernet@0 {
206 compatible = "smsc,lan9115";
207 reg = <0 0x10000>;
208 interrupts = <12 IRQ_TYPE_EDGE_RISING>;
209 interrupt-parent = <&gpio4>;
210 vdd33a-supply = <&en_3v3_reg>;
211 vddvario-supply = <&db8500_vape_reg>;
212 pinctrl-names = "default";
213 pinctrl-0 = <ð_snowball_mode>;
214
215 reg-shift = <1>;
216 reg-io-width = <2>;
217 smsc,force-internal-phy;
218 smsc,irq-active-high;
219 smsc,irq-push-pull;
220
221 clocks = <&prcc_pclk 3 0>;
222 };
223 };
224
225 /* ST6G3244ME level translator for 1.8/2.9 V */
226 vmmci: regulator-gpio {
227 compatible = "regulator-gpio";
228
229 /* GPIO228 SD_SEL */
230 gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
231 /* GPIO217 MMC_EN */
232 enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
233 enable-active-high;
234
235 regulator-min-microvolt = <1800000>;
236 regulator-max-microvolt = <2900000>;
237 regulator-name = "mmci-reg";
238 regulator-type = "voltage";
239
240 startup-delay-us = <100>;
241
242 states = <1800000 0x1
243 2900000 0x0>;
244 };
245
246 // External Micro SD slot
247 mmc@80126000 {
248 arm,primecell-periphid = <0x10480180>;
249 max-frequency = <100000000>;
250 bus-width = <4>;
251 cap-sd-highspeed;
252 cap-mmc-highspeed;
253 sd-uhs-sdr12;
254 sd-uhs-sdr25;
255 /* All direction control is used */
256 st,sig-dir-cmd;
257 st,sig-dir-dat0;
258 st,sig-dir-dat2;
259 st,sig-dir-dat31;
260 st,sig-pin-fbclk;
261 full-pwr-cycle;
262 vmmc-supply = <&ab8500_ldo_aux3_reg>;
263 vqmmc-supply = <&vmmci>;
264 pinctrl-names = "default", "sleep";
265 pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
266 pinctrl-1 = <&mc0_a_1_sleep>;
267
268 /* GPIO218 MMC_CD */
269 cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
270
271 status = "okay";
272 };
273
274 // WLAN SDIO channel
275 mmc@80118000 {
276 arm,primecell-periphid = <0x10480180>;
277 max-frequency = <100000000>;
278 bus-width = <4>;
279 pinctrl-names = "default", "sleep";
280 pinctrl-0 = <&mc1_a_1_default>;
281 pinctrl-1 = <&mc1_a_1_sleep>;
282
283 status = "okay";
284 };
285
286 // Unused PoP eMMC - register and put it to sleep by default */
287 mmc@80005000 {
288 arm,primecell-periphid = <0x10480180>;
289 pinctrl-names = "default";
290 pinctrl-0 = <&mc2_a_1_sleep>;
291
292 status = "okay";
293 };
294
295 // On-board eMMC
296 mmc@80114000 {
297 arm,primecell-periphid = <0x10480180>;
298 max-frequency = <100000000>;
299 bus-width = <8>;
300 cap-mmc-highspeed;
301 no-sdio;
302 no-sd;
303 vmmc-supply = <&ab8500_ldo_aux2_reg>;
304 pinctrl-names = "default", "sleep";
305 pinctrl-0 = <&mc4_a_1_default>;
306 pinctrl-1 = <&mc4_a_1_sleep>;
307
308 status = "okay";
309 };
310
311 uart@80120000 {
312 pinctrl-names = "default", "sleep";
313 pinctrl-0 = <&u0_a_1_default>;
314 pinctrl-1 = <&u0_a_1_sleep>;
315 status = "okay";
316 };
317
318 /* This UART is unused and thus left disabled */
319 uart@80121000 {
320 pinctrl-names = "default", "sleep";
321 pinctrl-0 = <&u1rxtx_a_1_default>;
322 pinctrl-1 = <&u1rxtx_a_1_sleep>;
323 };
324
325 uart@80007000 {
326 pinctrl-names = "default", "sleep";
327 pinctrl-0 = <&u2rxtx_c_1_default>;
328 pinctrl-1 = <&u2rxtx_c_1_sleep>;
329 status = "okay";
330 };
331
332 i2c@80004000 {
333 pinctrl-names = "default","sleep";
334 pinctrl-0 = <&i2c0_a_1_default>;
335 pinctrl-1 = <&i2c0_a_1_sleep>;
336 status = "okay";
337 };
338
339 i2c@80122000 {
340 pinctrl-names = "default","sleep";
341 pinctrl-0 = <&i2c1_b_2_default>;
342 pinctrl-1 = <&i2c1_b_2_sleep>;
343 status = "okay";
344 };
345
346 i2c@80128000 {
347 pinctrl-names = "default","sleep";
348 pinctrl-0 = <&i2c2_b_2_default>;
349 pinctrl-1 = <&i2c2_b_2_sleep>;
350 status = "okay";
351 lsm303dlh@18 {
352 /* Accelerometer */
353 compatible = "st,lsm303dlh-accel";
354 st,drdy-int-pin = <1>;
355 reg = <0x18>;
356 vdd-supply = <&ab8500_ldo_aux1_reg>;
357 vddio-supply = <&db8500_vsmps2_reg>;
358 pinctrl-names = "default";
359 pinctrl-0 = <&accel_snowball_mode>;
360 interrupt-parent = <&gpio5>;
361 interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
362 <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
363 };
364 lsm303dlh@1e {
365 /* Magnetometer */
366 compatible = "st,lsm303dlh-magn";
367 reg = <0x1e>;
368 vdd-supply = <&ab8500_ldo_aux1_reg>;
369 vddio-supply = <&db8500_vsmps2_reg>;
370 pinctrl-names = "default";
371 pinctrl-0 = <&magneto_snowball_mode>;
372 interrupt-parent = <&gpio5>;
373 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
374 };
375 l3g4200d@68 {
376 /* Gyroscope */
377 compatible = "st,l3g4200d-gyro";
378 st,drdy-int-pin = <2>;
379 reg = <0x68>;
380 vdd-supply = <&ab8500_ldo_aux1_reg>;
381 vddio-supply = <&db8500_vsmps2_reg>;
382 pinctrl-names = "default";
383 pinctrl-0 = <&gyro_snowball_mode>;
384 interrupt-parent = <&gpio5>;
385 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
386 <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
387 };
388 lsp001wm@5c {
389 /* Barometer/pressure sensor */
390 compatible = "st,lps001wp-press";
391 reg = <0x5c>;
392 vdd-supply = <&ab8500_ldo_aux1_reg>;
393 vddio-supply = <&db8500_vsmps2_reg>;
394 };
395 };
396
397 i2c@80110000 {
398 pinctrl-names = "default","sleep";
399 pinctrl-0 = <&i2c3_c_2_default>;
400 pinctrl-1 = <&i2c3_c_2_sleep>;
401 status = "okay";
402 };
403
404 spi@80002000 {
405 pinctrl-names = "default";
406 pinctrl-0 = <&ssp0_snowball_mode>;
407 status = "okay";
408 };
409
410 prcmu@80157000 {
411 ab8500 {
412 gpio {
413 /*
414 * AB8500 GPIOs are numbered starting from 1, so the first
415 * index 0 is what in the datasheet is called "GPIO1", and
416 * the second is "GPIO2" and so forth. Confusingly, the
417 * Snowball schematic then names the "GPIO2" line "PM_GPIO1".
418 * while later naming "GPIO4" as "PM_GPIO4".
419 */
420 gpio-line-names = "", /* AB8500 GPIO1 */
421 "PM_GPIO1", /* AB8500 GPIO2 */
422 "WLAN_CLK_REQ", /* AB8500 GPIO3 */
423 "PM_GPIO4", /* AB8500 GPIO4 */
424 "", "", "", "", "", "", "", "", "", "", "",
425 "EN_3V6", /* AB8500 GPIO16 */
426 "", "", "", "" ,"", "", "", "", "",
427 "EN_3V3", /* AB8500 GPIO26 */
428 "", "", "", "", "", "", "", "", "", "", "", "", "",
429 "PM_GPIO40", /* AB8500 GPIO40 */
430 "PM_GPIO41", /* AB8500 GPIO41 */
431 "PM_GPIO42"; /* AB8500 GPIO42 */
432 };
433
434 phy {
435 pinctrl-names = "default", "sleep";
436 pinctrl-0 = <&usb_a_1_default>;
437 pinctrl-1 = <&usb_a_1_sleep>;
438 };
439
440 ext_regulators: regulator-external {
441 ab8500_ext1_reg: ab8500_ext1 {
442 regulator-name = "ab8500-ext-supply1";
443 };
444
445 ab8500_ext2_reg_reg: ab8500_ext2 {
446 regulator-name = "ab8500-ext-supply2";
447 };
448
449 ab8500_ext3_reg_reg: ab8500_ext3 {
450 regulator-name = "ab8500-ext-supply3";
451 };
452 };
453
454 regulator {
455 ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
456 regulator-name = "V-DISPLAY";
457 };
458
459 ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
460 regulator-name = "V-eMMC1";
461 };
462
463 ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
464 regulator-name = "V-MMC-SD";
465 };
466
467 ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
468 regulator-name = "V-INTCORE";
469 };
470
471 ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
472 regulator-name = "V-TVOUT";
473 };
474
475 ab8500_ldo_audio_reg: ab8500_ldo_audio {
476 regulator-name = "V-AUD";
477 };
478
479 ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
480 regulator-name = "V-AMIC1";
481 };
482
483 ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
484 regulator-name = "V-AMIC2";
485 };
486
487 ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
488 regulator-name = "V-DMIC";
489 };
490
491 ab8500_ldo_ana_reg: ab8500_ldo_ana {
492 regulator-name = "V-CSI/DSI";
493 };
494 };
495 };
496 };
497
498 pinctrl {
499 /*
500 * Set this up using hogs, as time goes by and as seems fit, these
501 * can be moved over to being controlled by respective device.
502 */
503 pinctrl-names = "default";
504 pinctrl-0 = <&gbf_snowball_mode>,
505 <&wlan_snowball_mode>;
506
507 ethernet {
508 /*
509 * Mux in "SM" which is used for the
510 * SMSC911x Ethernet adapter
511 */
512 eth_snowball_mode: eth_snowball {
513 snowball_mux {
514 function = "sm";
515 groups = "sm_b_1";
516 };
517 /* LAN IRQ pin */
518 snowball_cfg1 {
519 pins = "GPIO140_B11";
520 ste,config = <&in_nopull>;
521 };
522 /* LAN reset pin */
523 snowball_cfg2 {
524 pins = "GPIO141_C12";
525 ste,config = <&gpio_out_hi>;
526 };
527
528 };
529 };
530 sdi0 {
531 sdi0_default_mode: sdi0_default {
532 snowball_mux {
533 function = "mc0";
534 /* Add the DAT31 pin even if it is not really used */
535 groups = "mc0dat31dir_a_1";
536 };
537 snowball_cfg1 {
538 pins = "GPIO21_AB3"; /* DAT31DIR */
539 ste,config = <&out_hi>;
540 };
541 /* SD card detect GPIO pin, extend default state */
542 snowball_cfg2 {
543 pins = "GPIO218_AH11";
544 ste,config = <&gpio_in_pu>;
545 };
546 /* VMMCI level-shifter enable */
547 snowball_cfg3 {
548 pins = "GPIO217_AH12";
549 ste,config = <&gpio_out_hi>;
550 };
551 /* VMMCI level-shifter voltage select */
552 snowball_cfg4 {
553 pins = "GPIO228_AJ6";
554 ste,config = <&gpio_out_hi>;
555 };
556 };
557 };
558 ssp0 {
559 ssp0_snowball_mode: ssp0_snowball_default {
560 snowball_mux {
561 function = "ssp0";
562 groups = "ssp0_a_1";
563 };
564 snowball_cfg1 {
565 pins = "GPIO144_B13"; /* FRM */
566 ste,config = <&gpio_out_hi>;
567 };
568 snowball_cfg2 {
569 pins = "GPIO145_C13"; /* RXD */
570 ste,config = <&in_pd>;
571 };
572 snowball_cfg3 {
573 pins =
574 "GPIO146_D13", /* TXD */
575 "GPIO143_D12"; /* CLK */
576 ste,config = <&out_lo>;
577 };
578
579 };
580 };
581 gpio_led {
582 gpioled_snowball_mode: gpioled_default {
583 snowball_cfg1 {
584 pins = "GPIO142_C11";
585 ste,config = <&gpio_out_hi>;
586 };
587
588 };
589 };
590 accelerometer {
591 accel_snowball_mode: accel_snowball {
592 /* Accelerometer lines */
593 snowball_cfg1 {
594 pins =
595 "GPIO163_C20", /* ACCEL_IRQ1 */
596 "GPIO164_B21"; /* ACCEL_IRQ2 */
597 ste,config = <&gpio_in_pu>;
598 };
599 };
600 };
601 gyro {
602 gyro_snowball_mode: gyro_snowball {
603 snowball_cfg1 {
604 pins =
605 "GPIO166_A22", /* DRDY */
606 "GPIO169_D22"; /* INT */
607 ste,config = <&gpio_in_pu>;
608 };
609 };
610 };
611 magnetometer {
612 magneto_snowball_mode: magneto_snowball {
613 snowball_cfg1 {
614 pins = "GPIO165_C21"; /* MAG_DRDY */
615 ste,config = <&gpio_in_pu>;
616 };
617 };
618 };
619 gbf {
620 gbf_snowball_mode: gbf_snowball {
621 /*
622 * GBF (GPS, Bluetooth, FM-radio) interface,
623 * pull low to reset state
624 */
625 snowball_cfg1 {
626 pins = "GPIO171_D23"; /* GBF_ENA_RESET */
627 ste,config = <&gpio_out_lo>;
628 };
629 };
630 };
631 wlan {
632 wlan_snowball_mode: wlan_snowball {
633 /*
634 * Activate this mode with the WLAN chip.
635 * These are plain GPIO pins used by WLAN
636 */
637 snowball_cfg1 {
638 pins =
639 "GPIO161_D21", /* WLAN_PMU_EN */
640 "GPIO215_AH13"; /* WLAN_ENA */
641 ste,config = <&gpio_out_lo>;
642 };
643 snowball_cfg2 {
644 pins = "GPIO216_AG12"; /* WLAN_IRQ */
645 ste,config = <&gpio_in_pu>;
646 };
647 };
648 };
649 };
650
651 mcde@a0350000 {
652 pinctrl-names = "default", "sleep";
653 pinctrl-0 = <&lcd_default_mode>;
654 pinctrl-1 = <&lcd_sleep_mode>;
655 };
656 };
657};
1/*
2 * Copyright 2011 ST-Ericsson AB
3 *
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
7 *
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
10 */
11
12/dts-v1/;
13#include "ste-dbx5x0.dtsi"
14#include "ste-href-ab8500.dtsi"
15#include "ste-href-family-pinctrl.dtsi"
16
17/ {
18 model = "Calao Systems Snowball platform with device tree";
19 compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
20
21 /* This stablilizes the serial port enumeration */
22 aliases {
23 serial0 = &ux500_serial0;
24 serial1 = &ux500_serial1;
25 serial2 = &ux500_serial2;
26 };
27
28 memory {
29 reg = <0x00000000 0x20000000>;
30 };
31
32 en_3v3_reg: en_3v3 {
33 compatible = "regulator-fixed";
34 regulator-name = "en-3v3-fixed-supply";
35 regulator-min-microvolt = <3300000>;
36 regulator-max-microvolt = <3300000>;
37 /* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
38 gpio = <&ab8500_gpio 25 0x4>;
39 startup-delay-us = <5000>;
40 enable-active-high;
41 };
42
43 gpio_keys {
44 compatible = "gpio-keys";
45 #address-cells = <1>;
46 #size-cells = <0>;
47
48 button@1 {
49 debounce_interval = <50>;
50 wakeup-source;
51 linux,code = <2>;
52 label = "userpb";
53 gpios = <&gpio1 0 0x4>;
54 };
55 button@2 {
56 debounce_interval = <50>;
57 wakeup-source;
58 linux,code = <3>;
59 label = "extkb1";
60 gpios = <&gpio4 23 0x4>;
61 };
62 button@3 {
63 debounce_interval = <50>;
64 wakeup-source;
65 linux,code = <4>;
66 label = "extkb2";
67 gpios = <&gpio4 24 0x4>;
68 };
69 button@4 {
70 debounce_interval = <50>;
71 wakeup-source;
72 linux,code = <5>;
73 label = "extkb3";
74 gpios = <&gpio5 1 0x4>;
75 };
76 button@5 {
77 debounce_interval = <50>;
78 wakeup-source;
79 linux,code = <6>;
80 label = "extkb4";
81 gpios = <&gpio5 2 0x4>;
82 };
83 };
84
85 leds {
86 compatible = "gpio-leds";
87 pinctrl-names = "default";
88 pinctrl-0 = <&gpioled_snowball_mode>;
89 used-led {
90 label = "user_led";
91 gpios = <&gpio4 14 0x4>;
92 default-state = "on";
93 linux,default-trigger = "heartbeat";
94 };
95 };
96
97 soc {
98 usb_per5@a03e0000 {
99 pinctrl-names = "default", "sleep";
100 pinctrl-0 = <&musb_default_mode>;
101 pinctrl-1 = <&musb_sleep_mode>;
102 };
103
104 sound {
105 compatible = "stericsson,snd-soc-mop500";
106
107 stericsson,cpu-dai = <&msp1 &msp3>;
108 stericsson,audio-codec = <&codec>;
109 };
110
111 msp0: msp@80123000 {
112 pinctrl-names = "default";
113 pinctrl-0 = <&msp0_default_mode>;
114 status = "okay";
115 };
116
117 msp1: msp@80124000 {
118 pinctrl-names = "default";
119 pinctrl-0 = <&msp1_default_mode>;
120 status = "okay";
121 };
122
123 msp2: msp@80117000 {
124 pinctrl-names = "default";
125 pinctrl-0 = <&msp2_default_mode>;
126 };
127
128 msp3: msp@80125000 {
129 status = "okay";
130 };
131
132 external-bus@50000000 {
133 status = "okay";
134
135 ethernet@0 {
136 compatible = "smsc,lan9115";
137 reg = <0 0x10000>;
138 interrupts = <12 IRQ_TYPE_EDGE_RISING>;
139 interrupt-parent = <&gpio4>;
140 vdd33a-supply = <&en_3v3_reg>;
141 vddvario-supply = <&db8500_vape_reg>;
142 pinctrl-names = "default";
143 pinctrl-0 = <ð_snowball_mode>;
144
145 reg-shift = <1>;
146 reg-io-width = <2>;
147 smsc,force-internal-phy;
148 smsc,irq-active-high;
149 smsc,irq-push-pull;
150
151 clocks = <&prcc_pclk 3 0>;
152 };
153 };
154
155 vmmci: regulator-gpio {
156 compatible = "regulator-gpio";
157
158 gpios = <&gpio7 4 0x4>;
159 enable-gpio = <&gpio6 25 0x4>;
160
161 regulator-min-microvolt = <1800000>;
162 regulator-max-microvolt = <2900000>;
163 regulator-name = "mmci-reg";
164 regulator-type = "voltage";
165
166 startup-delay-us = <100>;
167 enable-active-high;
168
169 states = <1800000 0x1
170 2900000 0x0>;
171 };
172
173 // External Micro SD slot
174 sdi0_per1@80126000 {
175 arm,primecell-periphid = <0x10480180>;
176 max-frequency = <100000000>;
177 bus-width = <4>;
178 cap-mmc-highspeed;
179 vmmc-supply = <&ab8500_ldo_aux3_reg>;
180 vqmmc-supply = <&vmmci>;
181 pinctrl-names = "default", "sleep";
182 pinctrl-0 = <&sdi0_default_mode>;
183 pinctrl-1 = <&sdi0_sleep_mode>;
184
185 cd-gpios = <&gpio6 26 0x4>; // 218
186 cd-inverted;
187
188 status = "okay";
189 };
190
191 // WLAN SDIO channel
192 sdi1_per2@80118000 {
193 arm,primecell-periphid = <0x10480180>;
194 max-frequency = <100000000>;
195 bus-width = <4>;
196 pinctrl-names = "default", "sleep";
197 pinctrl-0 = <&sdi1_default_mode>;
198 pinctrl-1 = <&sdi1_sleep_mode>;
199
200 status = "okay";
201 };
202
203 // Unused PoP eMMC - register and put it to sleep by default */
204 sdi2_per3@80005000 {
205 arm,primecell-periphid = <0x10480180>;
206 pinctrl-names = "default";
207 pinctrl-0 = <&sdi2_sleep_mode>;
208
209 status = "okay";
210 };
211
212 // On-board eMMC
213 sdi4_per2@80114000 {
214 arm,primecell-periphid = <0x10480180>;
215 max-frequency = <100000000>;
216 bus-width = <8>;
217 cap-mmc-highspeed;
218 vmmc-supply = <&ab8500_ldo_aux2_reg>;
219 pinctrl-names = "default", "sleep";
220 pinctrl-0 = <&sdi4_default_mode>;
221 pinctrl-1 = <&sdi4_sleep_mode>;
222
223 status = "okay";
224 };
225
226 uart@80120000 {
227 pinctrl-names = "default", "sleep";
228 pinctrl-0 = <&uart0_default_mode>;
229 pinctrl-1 = <&uart0_sleep_mode>;
230 status = "okay";
231 };
232
233 /* This UART is unused and thus left disabled */
234 uart@80121000 {
235 pinctrl-names = "default", "sleep";
236 pinctrl-0 = <&uart1_default_mode>;
237 pinctrl-1 = <&uart1_sleep_mode>;
238 };
239
240 uart@80007000 {
241 pinctrl-names = "default", "sleep";
242 pinctrl-0 = <&uart2_default_mode>;
243 pinctrl-1 = <&uart2_sleep_mode>;
244 status = "okay";
245 };
246
247 i2c@80004000 {
248 pinctrl-names = "default","sleep";
249 pinctrl-0 = <&i2c0_default_mode>;
250 pinctrl-1 = <&i2c0_sleep_mode>;
251 };
252
253 i2c@80122000 {
254 pinctrl-names = "default","sleep";
255 pinctrl-0 = <&i2c1_default_mode>;
256 pinctrl-1 = <&i2c1_sleep_mode>;
257 };
258
259 i2c@80128000 {
260 pinctrl-names = "default","sleep";
261 pinctrl-0 = <&i2c2_default_mode>;
262 pinctrl-1 = <&i2c2_sleep_mode>;
263 lsm303dlh@18 {
264 /* Accelerometer */
265 compatible = "st,lsm303dlh-accel";
266 st,drdy-int-pin = <1>;
267 reg = <0x18>;
268 vdd-supply = <&ab8500_ldo_aux1_reg>;
269 vddio-supply = <&db8500_vsmps2_reg>;
270 pinctrl-names = "default";
271 pinctrl-0 = <&accel_snowball_mode>;
272 interrupt-parent = <&gpio5>;
273 interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
274 <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
275 };
276 lsm303dlh@1e {
277 /* Magnetometer */
278 compatible = "st,lsm303dlh-magn";
279 reg = <0x1e>;
280 vdd-supply = <&ab8500_ldo_aux1_reg>;
281 vddio-supply = <&db8500_vsmps2_reg>;
282 pinctrl-names = "default";
283 pinctrl-0 = <&magneto_snowball_mode>;
284 interrupt-parent = <&gpio5>;
285 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
286 };
287 l3g4200d@68 {
288 /* Gyroscope */
289 compatible = "st,l3g4200d-gyro";
290 st,drdy-int-pin = <2>;
291 reg = <0x68>;
292 vdd-supply = <&ab8500_ldo_aux1_reg>;
293 vddio-supply = <&db8500_vsmps2_reg>;
294 pinctrl-names = "default";
295 pinctrl-0 = <&gyro_snowball_mode>;
296 interrupt-parent = <&gpio5>;
297 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
298 <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
299 };
300 lsp001wm@5c {
301 /* Barometer/pressure sensor */
302 compatible = "st,lps001wp-press";
303 reg = <0x5c>;
304 vdd-supply = <&ab8500_ldo_aux1_reg>;
305 vddio-supply = <&db8500_vsmps2_reg>;
306 };
307 };
308
309 i2c@80110000 {
310 pinctrl-names = "default","sleep";
311 pinctrl-0 = <&i2c3_default_mode>;
312 pinctrl-1 = <&i2c3_sleep_mode>;
313 };
314
315 ssp@80002000 {
316 pinctrl-names = "default";
317 pinctrl-0 = <&ssp0_snowball_mode>;
318 };
319
320 cpufreq-cooling {
321 status = "okay";
322 };
323
324 prcmu@80157000 {
325 cpufreq {
326 status = "okay";
327 };
328
329 thermal@801573c0 {
330 num-trips = <4>;
331
332 trip0-temp = <70000>;
333 trip0-type = "active";
334 trip0-cdev-num = <1>;
335 trip0-cdev-name0 = "thermal-cpufreq-0";
336
337 trip1-temp = <75000>;
338 trip1-type = "active";
339 trip1-cdev-num = <1>;
340 trip1-cdev-name0 = "thermal-cpufreq-0";
341
342 trip2-temp = <80000>;
343 trip2-type = "active";
344 trip2-cdev-num = <1>;
345 trip2-cdev-name0 = "thermal-cpufreq-0";
346
347 trip3-temp = <85000>;
348 trip3-type = "critical";
349 trip3-cdev-num = <0>;
350
351 status = "okay";
352 };
353
354 ab8500 {
355 ab8500-gpio {
356 compatible = "stericsson,ab8500-gpio";
357 };
358
359 ext_regulators: ab8500-ext-regulators {
360 ab8500_ext1_reg: ab8500_ext1 {
361 regulator-name = "ab8500-ext-supply1";
362 };
363
364 ab8500_ext2_reg_reg: ab8500_ext2 {
365 regulator-name = "ab8500-ext-supply2";
366 };
367
368 ab8500_ext3_reg_reg: ab8500_ext3 {
369 regulator-name = "ab8500-ext-supply3";
370 };
371 };
372
373 ab8500-regulators {
374 ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
375 regulator-name = "V-DISPLAY";
376 };
377
378 ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
379 regulator-name = "V-eMMC1";
380 };
381
382 ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
383 regulator-name = "V-MMC-SD";
384 };
385
386 ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
387 regulator-name = "V-INTCORE";
388 };
389
390 ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
391 regulator-name = "V-TVOUT";
392 };
393
394 ab8500_ldo_usb_reg: ab8500_ldo_usb {
395 regulator-name = "dummy";
396 };
397
398 ab8500_ldo_audio_reg: ab8500_ldo_audio {
399 regulator-name = "V-AUD";
400 };
401
402 ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
403 regulator-name = "V-AMIC1";
404 };
405
406 ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
407 regulator-name = "V-AMIC2";
408 };
409
410 ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
411 regulator-name = "V-DMIC";
412 };
413
414 ab8500_ldo_ana_reg: ab8500_ldo_ana {
415 regulator-name = "V-CSI/DSI";
416 };
417 };
418 };
419 };
420
421 pinctrl {
422 /*
423 * Set this up using hogs, as time goes by and as seems fit, these
424 * can be moved over to being controlled by respective device.
425 */
426 pinctrl-names = "default";
427 pinctrl-0 = <&gbf_snowball_mode>,
428 <&wlan_snowball_mode>;
429
430 ethernet {
431 /*
432 * Mux in "SM" which is used for the
433 * SMSC911x Ethernet adapter
434 */
435 eth_snowball_mode: eth_snowball {
436 snowball_mux {
437 function = "sm";
438 groups = "sm_b_1";
439 };
440 /* LAN IRQ pin */
441 snowball_cfg1 {
442 pins = "GPIO140_B11";
443 ste,config = <&in_nopull>;
444 };
445 /* LAN reset pin */
446 snowball_cfg2 {
447 pins = "GPIO141_C12";
448 ste,config = <&gpio_out_hi>;
449 };
450
451 };
452 };
453 sdi0 {
454 sdi0_default_mode: sdi0_default {
455 snowball_mux {
456 function = "mc0";
457 groups = "mc0dat31dir_a_1";
458 };
459 snowball_cfg1 {
460 pins = "GPIO21_AB3"; /* DAT31DIR */
461 ste,config = <&out_hi>;
462 };
463 /* SD card detect GPIO pin, extend default state */
464 snowball_cfg2 {
465 pins = "GPIO218_AH11";
466 ste,config = <&gpio_in_pu>;
467 };
468 /* VMMCI level-shifter enable */
469 snowball_cfg3 {
470 pins = "GPIO217_AH12";
471 ste,config = <&gpio_out_lo>;
472 };
473 /* VMMCI level-shifter voltage select */
474 snowball_cfg4 {
475 pins = "GPIO228_AJ6";
476 ste,config = <&gpio_out_hi>;
477 };
478 };
479 };
480 ssp0 {
481 ssp0_snowball_mode: ssp0_snowball_default {
482 snowball_mux {
483 function = "ssp0";
484 groups = "ssp0_a_1";
485 };
486 snowball_cfg1 {
487 pins = "GPIO144_B13"; /* FRM */
488 ste,config = <&gpio_out_hi>;
489 };
490 snowball_cfg2 {
491 pins = "GPIO145_C13"; /* RXD */
492 ste,config = <&in_pd>;
493 };
494 snowball_cfg3 {
495 pins =
496 "GPIO146_D13", /* TXD */
497 "GPIO143_D12"; /* CLK */
498 ste,config = <&out_lo>;
499 };
500
501 };
502 };
503 gpio_led {
504 gpioled_snowball_mode: gpioled_default {
505 snowball_cfg1 {
506 pins = "GPIO142_C11";
507 ste,config = <&gpio_out_hi>;
508 };
509
510 };
511 };
512 accelerometer {
513 accel_snowball_mode: accel_snowball {
514 /* Accelerometer lines */
515 snowball_cfg1 {
516 pins =
517 "GPIO163_C20", /* ACCEL_IRQ1 */
518 "GPIO164_B21"; /* ACCEL_IRQ2 */
519 ste,config = <&gpio_in_pu>;
520 };
521 };
522 };
523 gyro {
524 gyro_snowball_mode: gyro_snowball {
525 snowball_cfg1 {
526 pins =
527 "GPIO166_A22", /* DRDY */
528 "GPIO169_D22"; /* INT */
529 ste,config = <&gpio_in_pu>;
530 };
531 };
532 };
533 magnetometer {
534 magneto_snowball_mode: magneto_snowball {
535 snowball_cfg1 {
536 pins = "GPIO165_C21"; /* MAG_DRDY */
537 ste,config = <&gpio_in_pu>;
538 };
539 };
540 };
541 gbf {
542 gbf_snowball_mode: gbf_snowball {
543 /*
544 * GBF (GPS, Bluetooth, FM-radio) interface,
545 * pull low to reset state
546 */
547 snowball_cfg1 {
548 pins = "GPIO171_D23"; /* GBF_ENA_RESET */
549 ste,config = <&gpio_out_lo>;
550 };
551 };
552 };
553 wlan {
554 wlan_snowball_mode: wlan_snowball {
555 /*
556 * Activate this mode with the WLAN chip.
557 * These are plain GPIO pins used by WLAN
558 */
559 snowball_cfg1 {
560 pins =
561 "GPIO161_D21", /* WLAN_PMU_EN */
562 "GPIO215_AH13"; /* WLAN_ENA */
563 ste,config = <&gpio_out_lo>;
564 };
565 snowball_cfg2 {
566 pins = "GPIO216_AG12"; /* WLAN_IRQ */
567 ste,config = <&gpio_in_pu>;
568 };
569 };
570 };
571 };
572
573 mcde@a0350000 {
574 pinctrl-names = "default", "sleep";
575 pinctrl-0 = <&lcd_default_mode>;
576 pinctrl-1 = <&lcd_sleep_mode>;
577 };
578 };
579};