Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Platform level USB initialization for FS USB OTG controller on omap1
4 *
5 * Copyright (C) 2004 Texas Instruments, Inc.
6 */
7
8#include <linux/module.h>
9#include <linux/kernel.h>
10#include <linux/init.h>
11#include <linux/platform_device.h>
12#include <linux/dma-map-ops.h>
13#include <linux/io.h>
14#include <linux/delay.h>
15#include <linux/soc/ti/omap1-io.h>
16
17#include <asm/irq.h>
18
19#include "hardware.h"
20#include "mux.h"
21#include "usb.h"
22#include "common.h"
23
24/* These routines should handle the standard chip-specific modes
25 * for usb0/1/2 ports, covering basic mux and transceiver setup.
26 *
27 * Some board-*.c files will need to set up additional mux options,
28 * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
29 */
30
31/* TESTED ON:
32 * - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
33 * - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
34 * - 5912 OSK UDC, with *nonstandard* A-to-A cable
35 * - 1510 Innovator UDC with bundled usb0 cable
36 * - 1510 Innovator OHCI with bundled usb1/usb2 cable
37 * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
38 * - 1710 custom development board using alternate pin group
39 * - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
40 */
41
42#define INT_USB_IRQ_GEN IH2_BASE + 20
43#define INT_USB_IRQ_NISO IH2_BASE + 30
44#define INT_USB_IRQ_ISO IH2_BASE + 29
45#define INT_USB_IRQ_HGEN INT_USB_HHC_1
46#define INT_USB_IRQ_OTG IH2_BASE + 8
47
48#ifdef CONFIG_ARCH_OMAP_OTG
49
50static void __init
51omap_otg_init(struct omap_usb_config *config)
52{
53 u32 syscon;
54 int alt_pingroup = 0;
55 u16 w;
56
57 /* NOTE: no bus or clock setup (yet?) */
58
59 syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
60 if (!(syscon & OTG_RESET_DONE))
61 pr_debug("USB resets not complete?\n");
62
63 //omap_writew(0, OTG_IRQ_EN);
64
65 /* pin muxing and transceiver pinouts */
66 if (config->pins[0] > 2) /* alt pingroup 2 */
67 alt_pingroup = 1;
68 syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
69 syscon |= config->usb1_init(config->pins[1]);
70 syscon |= config->usb2_init(config->pins[2], alt_pingroup);
71 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
72 omap_writel(syscon, OTG_SYSCON_1);
73
74 syscon = config->hmc_mode;
75 syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
76#ifdef CONFIG_USB_OTG
77 if (config->otg)
78 syscon |= OTG_EN;
79#endif
80 pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
81 omap_readl(USB_TRANSCEIVER_CTRL));
82 pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
83 omap_writel(syscon, OTG_SYSCON_2);
84
85 printk("USB: hmc %d", config->hmc_mode);
86 if (!alt_pingroup)
87 pr_cont(", usb2 alt %d wires", config->pins[2]);
88 else if (config->pins[0])
89 pr_cont(", usb0 %d wires%s", config->pins[0],
90 is_usb0_device(config) ? " (dev)" : "");
91 if (config->pins[1])
92 pr_cont(", usb1 %d wires", config->pins[1]);
93 if (!alt_pingroup && config->pins[2])
94 pr_cont(", usb2 %d wires", config->pins[2]);
95 if (config->otg)
96 pr_cont(", Mini-AB on usb%d", config->otg - 1);
97 pr_cont("\n");
98
99 /* leave USB clocks/controllers off until needed */
100 w = omap_readw(ULPD_SOFT_REQ);
101 w &= ~SOFT_USB_CLK_REQ;
102 omap_writew(w, ULPD_SOFT_REQ);
103
104 w = omap_readw(ULPD_CLOCK_CTRL);
105 w &= ~USB_MCLK_EN;
106 w |= DIS_USB_PVCI_CLK;
107 omap_writew(w, ULPD_CLOCK_CTRL);
108
109 syscon = omap_readl(OTG_SYSCON_1);
110 syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
111
112#if IS_ENABLED(CONFIG_USB_OMAP)
113 if (config->otg || config->register_dev) {
114 struct platform_device *udc_device = config->udc_device;
115 int status;
116
117 syscon &= ~DEV_IDLE_EN;
118 udc_device->dev.platform_data = config;
119 status = platform_device_register(udc_device);
120 if (status)
121 pr_debug("can't register UDC device, %d\n", status);
122 }
123#endif
124
125#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
126 if (config->otg || config->register_host) {
127 struct platform_device *ohci_device = config->ohci_device;
128 int status;
129
130 syscon &= ~HST_IDLE_EN;
131 ohci_device->dev.platform_data = config;
132 status = platform_device_register(ohci_device);
133 if (status)
134 pr_debug("can't register OHCI device, %d\n", status);
135 }
136#endif
137
138#ifdef CONFIG_USB_OTG
139 if (config->otg) {
140 struct platform_device *otg_device = config->otg_device;
141 int status;
142
143 syscon &= ~OTG_IDLE_EN;
144 otg_device->dev.platform_data = config;
145 status = platform_device_register(otg_device);
146 if (status)
147 pr_debug("can't register OTG device, %d\n", status);
148 }
149#endif
150 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
151 omap_writel(syscon, OTG_SYSCON_1);
152}
153
154#else
155static void omap_otg_init(struct omap_usb_config *config) {}
156#endif
157
158#if IS_ENABLED(CONFIG_USB_OMAP)
159
160static struct resource udc_resources[] = {
161 /* order is significant! */
162 { /* registers */
163 .start = UDC_BASE,
164 .end = UDC_BASE + 0xff,
165 .flags = IORESOURCE_MEM,
166 }, { /* general IRQ */
167 .start = INT_USB_IRQ_GEN,
168 .flags = IORESOURCE_IRQ,
169 }, { /* PIO IRQ */
170 .start = INT_USB_IRQ_NISO,
171 .flags = IORESOURCE_IRQ,
172 }, { /* SOF IRQ */
173 .start = INT_USB_IRQ_ISO,
174 .flags = IORESOURCE_IRQ,
175 },
176};
177
178static u64 udc_dmamask = ~(u32)0;
179
180static struct platform_device udc_device = {
181 .name = "omap_udc",
182 .id = -1,
183 .dev = {
184 .dma_mask = &udc_dmamask,
185 .coherent_dma_mask = 0xffffffff,
186 },
187 .num_resources = ARRAY_SIZE(udc_resources),
188 .resource = udc_resources,
189};
190
191static inline void udc_device_init(struct omap_usb_config *pdata)
192{
193 pdata->udc_device = &udc_device;
194}
195
196#else
197
198static inline void udc_device_init(struct omap_usb_config *pdata)
199{
200}
201
202#endif
203
204/* The dmamask must be set for OHCI to work */
205static u64 ohci_dmamask = ~(u32)0;
206
207static struct resource ohci_resources[] = {
208 {
209 .start = OMAP_OHCI_BASE,
210 .end = OMAP_OHCI_BASE + 0xff,
211 .flags = IORESOURCE_MEM,
212 },
213 {
214 .start = INT_USB_IRQ_HGEN,
215 .flags = IORESOURCE_IRQ,
216 },
217};
218
219static struct platform_device ohci_device = {
220 .name = "ohci",
221 .id = -1,
222 .dev = {
223 .dma_mask = &ohci_dmamask,
224 .coherent_dma_mask = 0xffffffff,
225 },
226 .num_resources = ARRAY_SIZE(ohci_resources),
227 .resource = ohci_resources,
228};
229
230static inline void ohci_device_init(struct omap_usb_config *pdata)
231{
232 if (!IS_ENABLED(CONFIG_USB_OHCI_HCD))
233 return;
234
235 pdata->ohci_device = &ohci_device;
236 pdata->ocpi_enable = &ocpi_enable;
237}
238
239#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
240
241static struct resource otg_resources[] = {
242 /* order is significant! */
243 {
244 .start = OTG_BASE,
245 .end = OTG_BASE + 0xff,
246 .flags = IORESOURCE_MEM,
247 }, {
248 .start = INT_USB_IRQ_OTG,
249 .flags = IORESOURCE_IRQ,
250 },
251};
252
253static struct platform_device otg_device = {
254 .name = "omap_otg",
255 .id = -1,
256 .num_resources = ARRAY_SIZE(otg_resources),
257 .resource = otg_resources,
258};
259
260static inline void otg_device_init(struct omap_usb_config *pdata)
261{
262 pdata->otg_device = &otg_device;
263}
264
265#else
266
267static inline void otg_device_init(struct omap_usb_config *pdata)
268{
269}
270
271#endif
272
273static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
274{
275 u32 syscon1 = 0;
276
277 if (nwires == 0) {
278 if (!cpu_is_omap15xx()) {
279 u32 l;
280
281 /* pulldown D+/D- */
282 l = omap_readl(USB_TRANSCEIVER_CTRL);
283 l &= ~(3 << 1);
284 omap_writel(l, USB_TRANSCEIVER_CTRL);
285 }
286 return 0;
287 }
288
289 if (is_device) {
290 omap_cfg_reg(W4_USB_PUEN);
291 }
292
293 if (nwires == 2) {
294 u32 l;
295
296 // omap_cfg_reg(P9_USB_DP);
297 // omap_cfg_reg(R8_USB_DM);
298
299 if (cpu_is_omap15xx()) {
300 /* This works on 1510-Innovator */
301 return 0;
302 }
303
304 /* NOTES:
305 * - peripheral should configure VBUS detection!
306 * - only peripherals may use the internal D+/D- pulldowns
307 * - OTG support on this port not yet written
308 */
309
310 l = omap_readl(USB_TRANSCEIVER_CTRL);
311 l &= ~(7 << 4);
312 if (!is_device)
313 l |= (3 << 1);
314 omap_writel(l, USB_TRANSCEIVER_CTRL);
315
316 return 3 << 16;
317 }
318
319 /* alternate pin config, external transceiver */
320 if (cpu_is_omap15xx()) {
321 printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
322 return 0;
323 }
324
325 omap_cfg_reg(V6_USB0_TXD);
326 omap_cfg_reg(W9_USB0_TXEN);
327 omap_cfg_reg(W5_USB0_SE0);
328 if (nwires != 3)
329 omap_cfg_reg(Y5_USB0_RCV);
330
331 /* NOTE: SPEED and SUSP aren't configured here. OTG hosts
332 * may be able to use I2C requests to set those bits along
333 * with VBUS switching and overcurrent detection.
334 */
335
336 if (nwires != 6) {
337 u32 l;
338
339 l = omap_readl(USB_TRANSCEIVER_CTRL);
340 l &= ~CONF_USB2_UNI_R;
341 omap_writel(l, USB_TRANSCEIVER_CTRL);
342 }
343
344 switch (nwires) {
345 case 3:
346 syscon1 = 2;
347 break;
348 case 4:
349 syscon1 = 1;
350 break;
351 case 6:
352 syscon1 = 3;
353 {
354 u32 l;
355
356 omap_cfg_reg(AA9_USB0_VP);
357 omap_cfg_reg(R9_USB0_VM);
358 l = omap_readl(USB_TRANSCEIVER_CTRL);
359 l |= CONF_USB2_UNI_R;
360 omap_writel(l, USB_TRANSCEIVER_CTRL);
361 }
362 break;
363 default:
364 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
365 0, nwires);
366 }
367
368 return syscon1 << 16;
369}
370
371static u32 __init omap1_usb1_init(unsigned nwires)
372{
373 u32 syscon1 = 0;
374
375 if (!cpu_is_omap15xx() && nwires != 6) {
376 u32 l;
377
378 l = omap_readl(USB_TRANSCEIVER_CTRL);
379 l &= ~CONF_USB1_UNI_R;
380 omap_writel(l, USB_TRANSCEIVER_CTRL);
381 }
382 if (nwires == 0)
383 return 0;
384
385 /* external transceiver */
386 omap_cfg_reg(USB1_TXD);
387 omap_cfg_reg(USB1_TXEN);
388 if (nwires != 3)
389 omap_cfg_reg(USB1_RCV);
390
391 if (cpu_is_omap15xx()) {
392 omap_cfg_reg(USB1_SEO);
393 omap_cfg_reg(USB1_SPEED);
394 // SUSP
395 } else if (cpu_is_omap1610() || cpu_is_omap5912()) {
396 omap_cfg_reg(W13_1610_USB1_SE0);
397 omap_cfg_reg(R13_1610_USB1_SPEED);
398 // SUSP
399 } else if (cpu_is_omap1710()) {
400 omap_cfg_reg(R13_1710_USB1_SE0);
401 // SUSP
402 } else {
403 pr_debug("usb%d cpu unrecognized\n", 1);
404 return 0;
405 }
406
407 switch (nwires) {
408 case 2:
409 goto bad;
410 case 3:
411 syscon1 = 2;
412 break;
413 case 4:
414 syscon1 = 1;
415 break;
416 case 6:
417 syscon1 = 3;
418 omap_cfg_reg(USB1_VP);
419 omap_cfg_reg(USB1_VM);
420 if (!cpu_is_omap15xx()) {
421 u32 l;
422
423 l = omap_readl(USB_TRANSCEIVER_CTRL);
424 l |= CONF_USB1_UNI_R;
425 omap_writel(l, USB_TRANSCEIVER_CTRL);
426 }
427 break;
428 default:
429bad:
430 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
431 1, nwires);
432 }
433
434 return syscon1 << 20;
435}
436
437static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
438{
439 u32 syscon1 = 0;
440
441 /* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
442 if (alt_pingroup || nwires == 0)
443 return 0;
444
445 if (!cpu_is_omap15xx() && nwires != 6) {
446 u32 l;
447
448 l = omap_readl(USB_TRANSCEIVER_CTRL);
449 l &= ~CONF_USB2_UNI_R;
450 omap_writel(l, USB_TRANSCEIVER_CTRL);
451 }
452
453 /* external transceiver */
454 if (cpu_is_omap15xx()) {
455 omap_cfg_reg(USB2_TXD);
456 omap_cfg_reg(USB2_TXEN);
457 omap_cfg_reg(USB2_SEO);
458 if (nwires != 3)
459 omap_cfg_reg(USB2_RCV);
460 /* there is no USB2_SPEED */
461 } else if (cpu_is_omap16xx()) {
462 omap_cfg_reg(V6_USB2_TXD);
463 omap_cfg_reg(W9_USB2_TXEN);
464 omap_cfg_reg(W5_USB2_SE0);
465 if (nwires != 3)
466 omap_cfg_reg(Y5_USB2_RCV);
467 // FIXME omap_cfg_reg(USB2_SPEED);
468 } else {
469 pr_debug("usb%d cpu unrecognized\n", 1);
470 return 0;
471 }
472
473 // omap_cfg_reg(USB2_SUSP);
474
475 switch (nwires) {
476 case 2:
477 goto bad;
478 case 3:
479 syscon1 = 2;
480 break;
481 case 4:
482 syscon1 = 1;
483 break;
484 case 5:
485 goto bad;
486 case 6:
487 syscon1 = 3;
488 if (cpu_is_omap15xx()) {
489 omap_cfg_reg(USB2_VP);
490 omap_cfg_reg(USB2_VM);
491 } else {
492 u32 l;
493
494 omap_cfg_reg(AA9_USB2_VP);
495 omap_cfg_reg(R9_USB2_VM);
496 l = omap_readl(USB_TRANSCEIVER_CTRL);
497 l |= CONF_USB2_UNI_R;
498 omap_writel(l, USB_TRANSCEIVER_CTRL);
499 }
500 break;
501 default:
502bad:
503 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
504 2, nwires);
505 }
506
507 return syscon1 << 24;
508}
509
510#ifdef CONFIG_ARCH_OMAP15XX
511/* OMAP-1510 OHCI has its own MMU for DMA */
512#define OMAP1510_LB_MEMSIZE 32 /* Should be same as SDRAM size */
513#define OMAP1510_LB_CLOCK_DIV 0xfffec10c
514#define OMAP1510_LB_MMU_CTL 0xfffec208
515#define OMAP1510_LB_MMU_LCK 0xfffec224
516#define OMAP1510_LB_MMU_LD_TLB 0xfffec228
517#define OMAP1510_LB_MMU_CAM_H 0xfffec22c
518#define OMAP1510_LB_MMU_CAM_L 0xfffec230
519#define OMAP1510_LB_MMU_RAM_H 0xfffec234
520#define OMAP1510_LB_MMU_RAM_L 0xfffec238
521
522/*
523 * Bus address is physical address, except for OMAP-1510 Local Bus.
524 * OMAP-1510 bus address is translated into a Local Bus address if the
525 * OMAP bus type is lbus.
526 */
527#define OMAP1510_LB_OFFSET UL(0x30000000)
528
529/*
530 * OMAP-1510 specific Local Bus clock on/off
531 */
532static int omap_1510_local_bus_power(int on)
533{
534 if (on) {
535 omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
536 udelay(200);
537 } else {
538 omap_writel(0, OMAP1510_LB_MMU_CTL);
539 }
540
541 return 0;
542}
543
544/*
545 * OMAP-1510 specific Local Bus initialization
546 * NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
547 * See also arch/mach-omap/memory.h for __virt_to_dma() and
548 * __dma_to_virt() which need to match with the physical
549 * Local Bus address below.
550 */
551static int omap_1510_local_bus_init(void)
552{
553 unsigned int tlb;
554 unsigned long lbaddr, physaddr;
555
556 omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
557 OMAP1510_LB_CLOCK_DIV);
558
559 /* Configure the Local Bus MMU table */
560 for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
561 lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
562 physaddr = tlb * 0x00100000 + PHYS_OFFSET;
563 omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
564 omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
565 OMAP1510_LB_MMU_CAM_L);
566 omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
567 omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
568 omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
569 omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
570 }
571
572 /* Enable the walking table */
573 omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
574 udelay(200);
575
576 return 0;
577}
578
579static void omap_1510_local_bus_reset(void)
580{
581 omap_1510_local_bus_power(1);
582 omap_1510_local_bus_init();
583}
584
585/* ULPD_DPLL_CTRL */
586#define DPLL_IOB (1 << 13)
587#define DPLL_PLL_ENABLE (1 << 4)
588#define DPLL_LOCK (1 << 0)
589
590/* ULPD_APLL_CTRL */
591#define APLL_NDPLL_SWITCH (1 << 0)
592
593static void __init omap_1510_usb_init(struct omap_usb_config *config)
594{
595 unsigned int val;
596 u16 w;
597
598 config->usb0_init(config->pins[0], is_usb0_device(config));
599 config->usb1_init(config->pins[1]);
600 config->usb2_init(config->pins[2], 0);
601
602 val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
603 val |= (config->hmc_mode << 1);
604 omap_writel(val, MOD_CONF_CTRL_0);
605
606 printk("USB: hmc %d", config->hmc_mode);
607 if (config->pins[0])
608 pr_cont(", usb0 %d wires%s", config->pins[0],
609 is_usb0_device(config) ? " (dev)" : "");
610 if (config->pins[1])
611 pr_cont(", usb1 %d wires", config->pins[1]);
612 if (config->pins[2])
613 pr_cont(", usb2 %d wires", config->pins[2]);
614 pr_cont("\n");
615
616 /* use DPLL for 48 MHz function clock */
617 pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
618 omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
619
620 w = omap_readw(ULPD_APLL_CTRL);
621 w &= ~APLL_NDPLL_SWITCH;
622 omap_writew(w, ULPD_APLL_CTRL);
623
624 w = omap_readw(ULPD_DPLL_CTRL);
625 w |= DPLL_IOB | DPLL_PLL_ENABLE;
626 omap_writew(w, ULPD_DPLL_CTRL);
627
628 w = omap_readw(ULPD_SOFT_REQ);
629 w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
630 omap_writew(w, ULPD_SOFT_REQ);
631
632 while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
633 cpu_relax();
634
635#if IS_ENABLED(CONFIG_USB_OMAP)
636 if (config->register_dev) {
637 int status;
638
639 udc_device.dev.platform_data = config;
640 status = platform_device_register(&udc_device);
641 if (status)
642 pr_debug("can't register UDC device, %d\n", status);
643 /* udc driver gates 48MHz by D+ pullup */
644 }
645#endif
646
647 if (IS_ENABLED(CONFIG_USB_OHCI_HCD) && config->register_host) {
648 int status;
649
650 ohci_device.dev.platform_data = config;
651 dma_direct_set_offset(&ohci_device.dev, PHYS_OFFSET,
652 OMAP1510_LB_OFFSET, (u64)-1);
653 status = platform_device_register(&ohci_device);
654 if (status)
655 pr_debug("can't register OHCI device, %d\n", status);
656 /* hcd explicitly gates 48MHz */
657
658 config->lb_reset = omap_1510_local_bus_reset;
659 }
660}
661
662#else
663static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
664#endif
665
666void __init omap1_usb_init(struct omap_usb_config *_pdata)
667{
668 struct omap_usb_config *pdata;
669
670 pdata = kmemdup(_pdata, sizeof(*pdata), GFP_KERNEL);
671 if (!pdata)
672 return;
673
674 pdata->usb0_init = omap1_usb0_init;
675 pdata->usb1_init = omap1_usb1_init;
676 pdata->usb2_init = omap1_usb2_init;
677 udc_device_init(pdata);
678 ohci_device_init(pdata);
679 otg_device_init(pdata);
680
681 if (cpu_is_omap16xx())
682 omap_otg_init(pdata);
683 else if (cpu_is_omap15xx())
684 omap_1510_usb_init(pdata);
685 else
686 printk(KERN_ERR "USB: No init for your chip yet\n");
687}
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Platform level USB initialization for FS USB OTG controller on omap1
4 *
5 * Copyright (C) 2004 Texas Instruments, Inc.
6 */
7
8#include <linux/module.h>
9#include <linux/kernel.h>
10#include <linux/init.h>
11#include <linux/platform_device.h>
12#include <linux/io.h>
13
14#include <asm/irq.h>
15
16#include <mach/mux.h>
17
18#include <mach/usb.h>
19
20#include "common.h"
21
22/* These routines should handle the standard chip-specific modes
23 * for usb0/1/2 ports, covering basic mux and transceiver setup.
24 *
25 * Some board-*.c files will need to set up additional mux options,
26 * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
27 */
28
29/* TESTED ON:
30 * - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
31 * - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
32 * - 5912 OSK UDC, with *nonstandard* A-to-A cable
33 * - 1510 Innovator UDC with bundled usb0 cable
34 * - 1510 Innovator OHCI with bundled usb1/usb2 cable
35 * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
36 * - 1710 custom development board using alternate pin group
37 * - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
38 */
39
40#define INT_USB_IRQ_GEN IH2_BASE + 20
41#define INT_USB_IRQ_NISO IH2_BASE + 30
42#define INT_USB_IRQ_ISO IH2_BASE + 29
43#define INT_USB_IRQ_HGEN INT_USB_HHC_1
44#define INT_USB_IRQ_OTG IH2_BASE + 8
45
46#ifdef CONFIG_ARCH_OMAP_OTG
47
48static void __init
49omap_otg_init(struct omap_usb_config *config)
50{
51 u32 syscon;
52 int alt_pingroup = 0;
53 u16 w;
54
55 /* NOTE: no bus or clock setup (yet?) */
56
57 syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
58 if (!(syscon & OTG_RESET_DONE))
59 pr_debug("USB resets not complete?\n");
60
61 //omap_writew(0, OTG_IRQ_EN);
62
63 /* pin muxing and transceiver pinouts */
64 if (config->pins[0] > 2) /* alt pingroup 2 */
65 alt_pingroup = 1;
66 syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
67 syscon |= config->usb1_init(config->pins[1]);
68 syscon |= config->usb2_init(config->pins[2], alt_pingroup);
69 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
70 omap_writel(syscon, OTG_SYSCON_1);
71
72 syscon = config->hmc_mode;
73 syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
74#ifdef CONFIG_USB_OTG
75 if (config->otg)
76 syscon |= OTG_EN;
77#endif
78 pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
79 omap_readl(USB_TRANSCEIVER_CTRL));
80 pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
81 omap_writel(syscon, OTG_SYSCON_2);
82
83 printk("USB: hmc %d", config->hmc_mode);
84 if (!alt_pingroup)
85 pr_cont(", usb2 alt %d wires", config->pins[2]);
86 else if (config->pins[0])
87 pr_cont(", usb0 %d wires%s", config->pins[0],
88 is_usb0_device(config) ? " (dev)" : "");
89 if (config->pins[1])
90 pr_cont(", usb1 %d wires", config->pins[1]);
91 if (!alt_pingroup && config->pins[2])
92 pr_cont(", usb2 %d wires", config->pins[2]);
93 if (config->otg)
94 pr_cont(", Mini-AB on usb%d", config->otg - 1);
95 pr_cont("\n");
96
97 /* leave USB clocks/controllers off until needed */
98 w = omap_readw(ULPD_SOFT_REQ);
99 w &= ~SOFT_USB_CLK_REQ;
100 omap_writew(w, ULPD_SOFT_REQ);
101
102 w = omap_readw(ULPD_CLOCK_CTRL);
103 w &= ~USB_MCLK_EN;
104 w |= DIS_USB_PVCI_CLK;
105 omap_writew(w, ULPD_CLOCK_CTRL);
106
107 syscon = omap_readl(OTG_SYSCON_1);
108 syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
109
110#if IS_ENABLED(CONFIG_USB_OMAP)
111 if (config->otg || config->register_dev) {
112 struct platform_device *udc_device = config->udc_device;
113 int status;
114
115 syscon &= ~DEV_IDLE_EN;
116 udc_device->dev.platform_data = config;
117 status = platform_device_register(udc_device);
118 if (status)
119 pr_debug("can't register UDC device, %d\n", status);
120 }
121#endif
122
123#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
124 if (config->otg || config->register_host) {
125 struct platform_device *ohci_device = config->ohci_device;
126 int status;
127
128 syscon &= ~HST_IDLE_EN;
129 ohci_device->dev.platform_data = config;
130 status = platform_device_register(ohci_device);
131 if (status)
132 pr_debug("can't register OHCI device, %d\n", status);
133 }
134#endif
135
136#ifdef CONFIG_USB_OTG
137 if (config->otg) {
138 struct platform_device *otg_device = config->otg_device;
139 int status;
140
141 syscon &= ~OTG_IDLE_EN;
142 otg_device->dev.platform_data = config;
143 status = platform_device_register(otg_device);
144 if (status)
145 pr_debug("can't register OTG device, %d\n", status);
146 }
147#endif
148 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
149 omap_writel(syscon, OTG_SYSCON_1);
150}
151
152#else
153static void omap_otg_init(struct omap_usb_config *config) {}
154#endif
155
156#if IS_ENABLED(CONFIG_USB_OMAP)
157
158static struct resource udc_resources[] = {
159 /* order is significant! */
160 { /* registers */
161 .start = UDC_BASE,
162 .end = UDC_BASE + 0xff,
163 .flags = IORESOURCE_MEM,
164 }, { /* general IRQ */
165 .start = INT_USB_IRQ_GEN,
166 .flags = IORESOURCE_IRQ,
167 }, { /* PIO IRQ */
168 .start = INT_USB_IRQ_NISO,
169 .flags = IORESOURCE_IRQ,
170 }, { /* SOF IRQ */
171 .start = INT_USB_IRQ_ISO,
172 .flags = IORESOURCE_IRQ,
173 },
174};
175
176static u64 udc_dmamask = ~(u32)0;
177
178static struct platform_device udc_device = {
179 .name = "omap_udc",
180 .id = -1,
181 .dev = {
182 .dma_mask = &udc_dmamask,
183 .coherent_dma_mask = 0xffffffff,
184 },
185 .num_resources = ARRAY_SIZE(udc_resources),
186 .resource = udc_resources,
187};
188
189static inline void udc_device_init(struct omap_usb_config *pdata)
190{
191 /* IRQ numbers for omap7xx */
192 if(cpu_is_omap7xx()) {
193 udc_resources[1].start = INT_7XX_USB_GENI;
194 udc_resources[2].start = INT_7XX_USB_NON_ISO;
195 udc_resources[3].start = INT_7XX_USB_ISO;
196 }
197 pdata->udc_device = &udc_device;
198}
199
200#else
201
202static inline void udc_device_init(struct omap_usb_config *pdata)
203{
204}
205
206#endif
207
208#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
209
210/* The dmamask must be set for OHCI to work */
211static u64 ohci_dmamask = ~(u32)0;
212
213static struct resource ohci_resources[] = {
214 {
215 .start = OMAP_OHCI_BASE,
216 .end = OMAP_OHCI_BASE + 0xff,
217 .flags = IORESOURCE_MEM,
218 },
219 {
220 .start = INT_USB_IRQ_HGEN,
221 .flags = IORESOURCE_IRQ,
222 },
223};
224
225static struct platform_device ohci_device = {
226 .name = "ohci",
227 .id = -1,
228 .dev = {
229 .dma_mask = &ohci_dmamask,
230 .coherent_dma_mask = 0xffffffff,
231 },
232 .num_resources = ARRAY_SIZE(ohci_resources),
233 .resource = ohci_resources,
234};
235
236static inline void ohci_device_init(struct omap_usb_config *pdata)
237{
238 if (cpu_is_omap7xx())
239 ohci_resources[1].start = INT_7XX_USB_HHC_1;
240 pdata->ohci_device = &ohci_device;
241 pdata->ocpi_enable = &ocpi_enable;
242}
243
244#else
245
246static inline void ohci_device_init(struct omap_usb_config *pdata)
247{
248}
249
250#endif
251
252#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
253
254static struct resource otg_resources[] = {
255 /* order is significant! */
256 {
257 .start = OTG_BASE,
258 .end = OTG_BASE + 0xff,
259 .flags = IORESOURCE_MEM,
260 }, {
261 .start = INT_USB_IRQ_OTG,
262 .flags = IORESOURCE_IRQ,
263 },
264};
265
266static struct platform_device otg_device = {
267 .name = "omap_otg",
268 .id = -1,
269 .num_resources = ARRAY_SIZE(otg_resources),
270 .resource = otg_resources,
271};
272
273static inline void otg_device_init(struct omap_usb_config *pdata)
274{
275 if (cpu_is_omap7xx())
276 otg_resources[1].start = INT_7XX_USB_OTG;
277 pdata->otg_device = &otg_device;
278}
279
280#else
281
282static inline void otg_device_init(struct omap_usb_config *pdata)
283{
284}
285
286#endif
287
288static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
289{
290 u32 syscon1 = 0;
291
292 if (nwires == 0) {
293 if (!cpu_is_omap15xx()) {
294 u32 l;
295
296 /* pulldown D+/D- */
297 l = omap_readl(USB_TRANSCEIVER_CTRL);
298 l &= ~(3 << 1);
299 omap_writel(l, USB_TRANSCEIVER_CTRL);
300 }
301 return 0;
302 }
303
304 if (is_device) {
305 if (cpu_is_omap7xx()) {
306 omap_cfg_reg(AA17_7XX_USB_DM);
307 omap_cfg_reg(W16_7XX_USB_PU_EN);
308 omap_cfg_reg(W17_7XX_USB_VBUSI);
309 omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
310 omap_cfg_reg(W19_7XX_USB_DCRST);
311 } else
312 omap_cfg_reg(W4_USB_PUEN);
313 }
314
315 if (nwires == 2) {
316 u32 l;
317
318 // omap_cfg_reg(P9_USB_DP);
319 // omap_cfg_reg(R8_USB_DM);
320
321 if (cpu_is_omap15xx()) {
322 /* This works on 1510-Innovator */
323 return 0;
324 }
325
326 /* NOTES:
327 * - peripheral should configure VBUS detection!
328 * - only peripherals may use the internal D+/D- pulldowns
329 * - OTG support on this port not yet written
330 */
331
332 /* Don't do this for omap7xx -- it causes USB to not work correctly */
333 if (!cpu_is_omap7xx()) {
334 l = omap_readl(USB_TRANSCEIVER_CTRL);
335 l &= ~(7 << 4);
336 if (!is_device)
337 l |= (3 << 1);
338 omap_writel(l, USB_TRANSCEIVER_CTRL);
339 }
340
341 return 3 << 16;
342 }
343
344 /* alternate pin config, external transceiver */
345 if (cpu_is_omap15xx()) {
346 printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
347 return 0;
348 }
349
350 omap_cfg_reg(V6_USB0_TXD);
351 omap_cfg_reg(W9_USB0_TXEN);
352 omap_cfg_reg(W5_USB0_SE0);
353 if (nwires != 3)
354 omap_cfg_reg(Y5_USB0_RCV);
355
356 /* NOTE: SPEED and SUSP aren't configured here. OTG hosts
357 * may be able to use I2C requests to set those bits along
358 * with VBUS switching and overcurrent detection.
359 */
360
361 if (nwires != 6) {
362 u32 l;
363
364 l = omap_readl(USB_TRANSCEIVER_CTRL);
365 l &= ~CONF_USB2_UNI_R;
366 omap_writel(l, USB_TRANSCEIVER_CTRL);
367 }
368
369 switch (nwires) {
370 case 3:
371 syscon1 = 2;
372 break;
373 case 4:
374 syscon1 = 1;
375 break;
376 case 6:
377 syscon1 = 3;
378 {
379 u32 l;
380
381 omap_cfg_reg(AA9_USB0_VP);
382 omap_cfg_reg(R9_USB0_VM);
383 l = omap_readl(USB_TRANSCEIVER_CTRL);
384 l |= CONF_USB2_UNI_R;
385 omap_writel(l, USB_TRANSCEIVER_CTRL);
386 }
387 break;
388 default:
389 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
390 0, nwires);
391 }
392
393 return syscon1 << 16;
394}
395
396static u32 __init omap1_usb1_init(unsigned nwires)
397{
398 u32 syscon1 = 0;
399
400 if (!cpu_is_omap15xx() && nwires != 6) {
401 u32 l;
402
403 l = omap_readl(USB_TRANSCEIVER_CTRL);
404 l &= ~CONF_USB1_UNI_R;
405 omap_writel(l, USB_TRANSCEIVER_CTRL);
406 }
407 if (nwires == 0)
408 return 0;
409
410 /* external transceiver */
411 omap_cfg_reg(USB1_TXD);
412 omap_cfg_reg(USB1_TXEN);
413 if (nwires != 3)
414 omap_cfg_reg(USB1_RCV);
415
416 if (cpu_is_omap15xx()) {
417 omap_cfg_reg(USB1_SEO);
418 omap_cfg_reg(USB1_SPEED);
419 // SUSP
420 } else if (cpu_is_omap1610() || cpu_is_omap5912()) {
421 omap_cfg_reg(W13_1610_USB1_SE0);
422 omap_cfg_reg(R13_1610_USB1_SPEED);
423 // SUSP
424 } else if (cpu_is_omap1710()) {
425 omap_cfg_reg(R13_1710_USB1_SE0);
426 // SUSP
427 } else {
428 pr_debug("usb%d cpu unrecognized\n", 1);
429 return 0;
430 }
431
432 switch (nwires) {
433 case 2:
434 goto bad;
435 case 3:
436 syscon1 = 2;
437 break;
438 case 4:
439 syscon1 = 1;
440 break;
441 case 6:
442 syscon1 = 3;
443 omap_cfg_reg(USB1_VP);
444 omap_cfg_reg(USB1_VM);
445 if (!cpu_is_omap15xx()) {
446 u32 l;
447
448 l = omap_readl(USB_TRANSCEIVER_CTRL);
449 l |= CONF_USB1_UNI_R;
450 omap_writel(l, USB_TRANSCEIVER_CTRL);
451 }
452 break;
453 default:
454bad:
455 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
456 1, nwires);
457 }
458
459 return syscon1 << 20;
460}
461
462static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
463{
464 u32 syscon1 = 0;
465
466 /* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
467 if (alt_pingroup || nwires == 0)
468 return 0;
469
470 if (!cpu_is_omap15xx() && nwires != 6) {
471 u32 l;
472
473 l = omap_readl(USB_TRANSCEIVER_CTRL);
474 l &= ~CONF_USB2_UNI_R;
475 omap_writel(l, USB_TRANSCEIVER_CTRL);
476 }
477
478 /* external transceiver */
479 if (cpu_is_omap15xx()) {
480 omap_cfg_reg(USB2_TXD);
481 omap_cfg_reg(USB2_TXEN);
482 omap_cfg_reg(USB2_SEO);
483 if (nwires != 3)
484 omap_cfg_reg(USB2_RCV);
485 /* there is no USB2_SPEED */
486 } else if (cpu_is_omap16xx()) {
487 omap_cfg_reg(V6_USB2_TXD);
488 omap_cfg_reg(W9_USB2_TXEN);
489 omap_cfg_reg(W5_USB2_SE0);
490 if (nwires != 3)
491 omap_cfg_reg(Y5_USB2_RCV);
492 // FIXME omap_cfg_reg(USB2_SPEED);
493 } else {
494 pr_debug("usb%d cpu unrecognized\n", 1);
495 return 0;
496 }
497
498 // omap_cfg_reg(USB2_SUSP);
499
500 switch (nwires) {
501 case 2:
502 goto bad;
503 case 3:
504 syscon1 = 2;
505 break;
506 case 4:
507 syscon1 = 1;
508 break;
509 case 5:
510 goto bad;
511 case 6:
512 syscon1 = 3;
513 if (cpu_is_omap15xx()) {
514 omap_cfg_reg(USB2_VP);
515 omap_cfg_reg(USB2_VM);
516 } else {
517 u32 l;
518
519 omap_cfg_reg(AA9_USB2_VP);
520 omap_cfg_reg(R9_USB2_VM);
521 l = omap_readl(USB_TRANSCEIVER_CTRL);
522 l |= CONF_USB2_UNI_R;
523 omap_writel(l, USB_TRANSCEIVER_CTRL);
524 }
525 break;
526 default:
527bad:
528 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
529 2, nwires);
530 }
531
532 return syscon1 << 24;
533}
534
535#ifdef CONFIG_ARCH_OMAP15XX
536
537/* ULPD_DPLL_CTRL */
538#define DPLL_IOB (1 << 13)
539#define DPLL_PLL_ENABLE (1 << 4)
540#define DPLL_LOCK (1 << 0)
541
542/* ULPD_APLL_CTRL */
543#define APLL_NDPLL_SWITCH (1 << 0)
544
545static void __init omap_1510_usb_init(struct omap_usb_config *config)
546{
547 unsigned int val;
548 u16 w;
549
550 config->usb0_init(config->pins[0], is_usb0_device(config));
551 config->usb1_init(config->pins[1]);
552 config->usb2_init(config->pins[2], 0);
553
554 val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
555 val |= (config->hmc_mode << 1);
556 omap_writel(val, MOD_CONF_CTRL_0);
557
558 printk("USB: hmc %d", config->hmc_mode);
559 if (config->pins[0])
560 pr_cont(", usb0 %d wires%s", config->pins[0],
561 is_usb0_device(config) ? " (dev)" : "");
562 if (config->pins[1])
563 pr_cont(", usb1 %d wires", config->pins[1]);
564 if (config->pins[2])
565 pr_cont(", usb2 %d wires", config->pins[2]);
566 pr_cont("\n");
567
568 /* use DPLL for 48 MHz function clock */
569 pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
570 omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
571
572 w = omap_readw(ULPD_APLL_CTRL);
573 w &= ~APLL_NDPLL_SWITCH;
574 omap_writew(w, ULPD_APLL_CTRL);
575
576 w = omap_readw(ULPD_DPLL_CTRL);
577 w |= DPLL_IOB | DPLL_PLL_ENABLE;
578 omap_writew(w, ULPD_DPLL_CTRL);
579
580 w = omap_readw(ULPD_SOFT_REQ);
581 w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
582 omap_writew(w, ULPD_SOFT_REQ);
583
584 while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
585 cpu_relax();
586
587#if IS_ENABLED(CONFIG_USB_OMAP)
588 if (config->register_dev) {
589 int status;
590
591 udc_device.dev.platform_data = config;
592 status = platform_device_register(&udc_device);
593 if (status)
594 pr_debug("can't register UDC device, %d\n", status);
595 /* udc driver gates 48MHz by D+ pullup */
596 }
597#endif
598
599#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
600 if (config->register_host) {
601 int status;
602
603 ohci_device.dev.platform_data = config;
604 status = platform_device_register(&ohci_device);
605 if (status)
606 pr_debug("can't register OHCI device, %d\n", status);
607 /* hcd explicitly gates 48MHz */
608 }
609#endif
610}
611
612#else
613static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
614#endif
615
616void __init omap1_usb_init(struct omap_usb_config *_pdata)
617{
618 struct omap_usb_config *pdata;
619
620 pdata = kmemdup(_pdata, sizeof(*pdata), GFP_KERNEL);
621 if (!pdata)
622 return;
623
624 pdata->usb0_init = omap1_usb0_init;
625 pdata->usb1_init = omap1_usb1_init;
626 pdata->usb2_init = omap1_usb2_init;
627 udc_device_init(pdata);
628 ohci_device_init(pdata);
629 otg_device_init(pdata);
630
631 if (cpu_is_omap7xx() || cpu_is_omap16xx())
632 omap_otg_init(pdata);
633 else if (cpu_is_omap15xx())
634 omap_1510_usb_init(pdata);
635 else
636 printk(KERN_ERR "USB: No init for your chip yet\n");
637}