Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Platform level USB initialization for FS USB OTG controller on omap1
4 *
5 * Copyright (C) 2004 Texas Instruments, Inc.
6 */
7
8#include <linux/module.h>
9#include <linux/kernel.h>
10#include <linux/init.h>
11#include <linux/platform_device.h>
12#include <linux/dma-map-ops.h>
13#include <linux/io.h>
14#include <linux/delay.h>
15#include <linux/soc/ti/omap1-io.h>
16
17#include <asm/irq.h>
18
19#include "hardware.h"
20#include "mux.h"
21#include "usb.h"
22#include "common.h"
23
24/* These routines should handle the standard chip-specific modes
25 * for usb0/1/2 ports, covering basic mux and transceiver setup.
26 *
27 * Some board-*.c files will need to set up additional mux options,
28 * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
29 */
30
31/* TESTED ON:
32 * - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
33 * - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
34 * - 5912 OSK UDC, with *nonstandard* A-to-A cable
35 * - 1510 Innovator UDC with bundled usb0 cable
36 * - 1510 Innovator OHCI with bundled usb1/usb2 cable
37 * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
38 * - 1710 custom development board using alternate pin group
39 * - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
40 */
41
42#define INT_USB_IRQ_GEN IH2_BASE + 20
43#define INT_USB_IRQ_NISO IH2_BASE + 30
44#define INT_USB_IRQ_ISO IH2_BASE + 29
45#define INT_USB_IRQ_HGEN INT_USB_HHC_1
46#define INT_USB_IRQ_OTG IH2_BASE + 8
47
48#ifdef CONFIG_ARCH_OMAP_OTG
49
50static void __init
51omap_otg_init(struct omap_usb_config *config)
52{
53 u32 syscon;
54 int alt_pingroup = 0;
55 u16 w;
56
57 /* NOTE: no bus or clock setup (yet?) */
58
59 syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
60 if (!(syscon & OTG_RESET_DONE))
61 pr_debug("USB resets not complete?\n");
62
63 //omap_writew(0, OTG_IRQ_EN);
64
65 /* pin muxing and transceiver pinouts */
66 if (config->pins[0] > 2) /* alt pingroup 2 */
67 alt_pingroup = 1;
68 syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
69 syscon |= config->usb1_init(config->pins[1]);
70 syscon |= config->usb2_init(config->pins[2], alt_pingroup);
71 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
72 omap_writel(syscon, OTG_SYSCON_1);
73
74 syscon = config->hmc_mode;
75 syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
76#ifdef CONFIG_USB_OTG
77 if (config->otg)
78 syscon |= OTG_EN;
79#endif
80 pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
81 omap_readl(USB_TRANSCEIVER_CTRL));
82 pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
83 omap_writel(syscon, OTG_SYSCON_2);
84
85 printk("USB: hmc %d", config->hmc_mode);
86 if (!alt_pingroup)
87 pr_cont(", usb2 alt %d wires", config->pins[2]);
88 else if (config->pins[0])
89 pr_cont(", usb0 %d wires%s", config->pins[0],
90 is_usb0_device(config) ? " (dev)" : "");
91 if (config->pins[1])
92 pr_cont(", usb1 %d wires", config->pins[1]);
93 if (!alt_pingroup && config->pins[2])
94 pr_cont(", usb2 %d wires", config->pins[2]);
95 if (config->otg)
96 pr_cont(", Mini-AB on usb%d", config->otg - 1);
97 pr_cont("\n");
98
99 /* leave USB clocks/controllers off until needed */
100 w = omap_readw(ULPD_SOFT_REQ);
101 w &= ~SOFT_USB_CLK_REQ;
102 omap_writew(w, ULPD_SOFT_REQ);
103
104 w = omap_readw(ULPD_CLOCK_CTRL);
105 w &= ~USB_MCLK_EN;
106 w |= DIS_USB_PVCI_CLK;
107 omap_writew(w, ULPD_CLOCK_CTRL);
108
109 syscon = omap_readl(OTG_SYSCON_1);
110 syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
111
112#if IS_ENABLED(CONFIG_USB_OMAP)
113 if (config->otg || config->register_dev) {
114 struct platform_device *udc_device = config->udc_device;
115 int status;
116
117 syscon &= ~DEV_IDLE_EN;
118 udc_device->dev.platform_data = config;
119 status = platform_device_register(udc_device);
120 if (status)
121 pr_debug("can't register UDC device, %d\n", status);
122 }
123#endif
124
125#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
126 if (config->otg || config->register_host) {
127 struct platform_device *ohci_device = config->ohci_device;
128 int status;
129
130 syscon &= ~HST_IDLE_EN;
131 ohci_device->dev.platform_data = config;
132 status = platform_device_register(ohci_device);
133 if (status)
134 pr_debug("can't register OHCI device, %d\n", status);
135 }
136#endif
137
138#ifdef CONFIG_USB_OTG
139 if (config->otg) {
140 struct platform_device *otg_device = config->otg_device;
141 int status;
142
143 syscon &= ~OTG_IDLE_EN;
144 otg_device->dev.platform_data = config;
145 status = platform_device_register(otg_device);
146 if (status)
147 pr_debug("can't register OTG device, %d\n", status);
148 }
149#endif
150 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
151 omap_writel(syscon, OTG_SYSCON_1);
152}
153
154#else
155static void omap_otg_init(struct omap_usb_config *config) {}
156#endif
157
158#if IS_ENABLED(CONFIG_USB_OMAP)
159
160static struct resource udc_resources[] = {
161 /* order is significant! */
162 { /* registers */
163 .start = UDC_BASE,
164 .end = UDC_BASE + 0xff,
165 .flags = IORESOURCE_MEM,
166 }, { /* general IRQ */
167 .start = INT_USB_IRQ_GEN,
168 .flags = IORESOURCE_IRQ,
169 }, { /* PIO IRQ */
170 .start = INT_USB_IRQ_NISO,
171 .flags = IORESOURCE_IRQ,
172 }, { /* SOF IRQ */
173 .start = INT_USB_IRQ_ISO,
174 .flags = IORESOURCE_IRQ,
175 },
176};
177
178static u64 udc_dmamask = ~(u32)0;
179
180static struct platform_device udc_device = {
181 .name = "omap_udc",
182 .id = -1,
183 .dev = {
184 .dma_mask = &udc_dmamask,
185 .coherent_dma_mask = 0xffffffff,
186 },
187 .num_resources = ARRAY_SIZE(udc_resources),
188 .resource = udc_resources,
189};
190
191static inline void udc_device_init(struct omap_usb_config *pdata)
192{
193 pdata->udc_device = &udc_device;
194}
195
196#else
197
198static inline void udc_device_init(struct omap_usb_config *pdata)
199{
200}
201
202#endif
203
204/* The dmamask must be set for OHCI to work */
205static u64 ohci_dmamask = ~(u32)0;
206
207static struct resource ohci_resources[] = {
208 {
209 .start = OMAP_OHCI_BASE,
210 .end = OMAP_OHCI_BASE + 0xff,
211 .flags = IORESOURCE_MEM,
212 },
213 {
214 .start = INT_USB_IRQ_HGEN,
215 .flags = IORESOURCE_IRQ,
216 },
217};
218
219static struct platform_device ohci_device = {
220 .name = "ohci",
221 .id = -1,
222 .dev = {
223 .dma_mask = &ohci_dmamask,
224 .coherent_dma_mask = 0xffffffff,
225 },
226 .num_resources = ARRAY_SIZE(ohci_resources),
227 .resource = ohci_resources,
228};
229
230static inline void ohci_device_init(struct omap_usb_config *pdata)
231{
232 if (!IS_ENABLED(CONFIG_USB_OHCI_HCD))
233 return;
234
235 pdata->ohci_device = &ohci_device;
236 pdata->ocpi_enable = &ocpi_enable;
237}
238
239#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
240
241static struct resource otg_resources[] = {
242 /* order is significant! */
243 {
244 .start = OTG_BASE,
245 .end = OTG_BASE + 0xff,
246 .flags = IORESOURCE_MEM,
247 }, {
248 .start = INT_USB_IRQ_OTG,
249 .flags = IORESOURCE_IRQ,
250 },
251};
252
253static struct platform_device otg_device = {
254 .name = "omap_otg",
255 .id = -1,
256 .num_resources = ARRAY_SIZE(otg_resources),
257 .resource = otg_resources,
258};
259
260static inline void otg_device_init(struct omap_usb_config *pdata)
261{
262 pdata->otg_device = &otg_device;
263}
264
265#else
266
267static inline void otg_device_init(struct omap_usb_config *pdata)
268{
269}
270
271#endif
272
273static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
274{
275 u32 syscon1 = 0;
276
277 if (nwires == 0) {
278 if (!cpu_is_omap15xx()) {
279 u32 l;
280
281 /* pulldown D+/D- */
282 l = omap_readl(USB_TRANSCEIVER_CTRL);
283 l &= ~(3 << 1);
284 omap_writel(l, USB_TRANSCEIVER_CTRL);
285 }
286 return 0;
287 }
288
289 if (is_device) {
290 omap_cfg_reg(W4_USB_PUEN);
291 }
292
293 if (nwires == 2) {
294 u32 l;
295
296 // omap_cfg_reg(P9_USB_DP);
297 // omap_cfg_reg(R8_USB_DM);
298
299 if (cpu_is_omap15xx()) {
300 /* This works on 1510-Innovator */
301 return 0;
302 }
303
304 /* NOTES:
305 * - peripheral should configure VBUS detection!
306 * - only peripherals may use the internal D+/D- pulldowns
307 * - OTG support on this port not yet written
308 */
309
310 l = omap_readl(USB_TRANSCEIVER_CTRL);
311 l &= ~(7 << 4);
312 if (!is_device)
313 l |= (3 << 1);
314 omap_writel(l, USB_TRANSCEIVER_CTRL);
315
316 return 3 << 16;
317 }
318
319 /* alternate pin config, external transceiver */
320 if (cpu_is_omap15xx()) {
321 printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
322 return 0;
323 }
324
325 omap_cfg_reg(V6_USB0_TXD);
326 omap_cfg_reg(W9_USB0_TXEN);
327 omap_cfg_reg(W5_USB0_SE0);
328 if (nwires != 3)
329 omap_cfg_reg(Y5_USB0_RCV);
330
331 /* NOTE: SPEED and SUSP aren't configured here. OTG hosts
332 * may be able to use I2C requests to set those bits along
333 * with VBUS switching and overcurrent detection.
334 */
335
336 if (nwires != 6) {
337 u32 l;
338
339 l = omap_readl(USB_TRANSCEIVER_CTRL);
340 l &= ~CONF_USB2_UNI_R;
341 omap_writel(l, USB_TRANSCEIVER_CTRL);
342 }
343
344 switch (nwires) {
345 case 3:
346 syscon1 = 2;
347 break;
348 case 4:
349 syscon1 = 1;
350 break;
351 case 6:
352 syscon1 = 3;
353 {
354 u32 l;
355
356 omap_cfg_reg(AA9_USB0_VP);
357 omap_cfg_reg(R9_USB0_VM);
358 l = omap_readl(USB_TRANSCEIVER_CTRL);
359 l |= CONF_USB2_UNI_R;
360 omap_writel(l, USB_TRANSCEIVER_CTRL);
361 }
362 break;
363 default:
364 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
365 0, nwires);
366 }
367
368 return syscon1 << 16;
369}
370
371static u32 __init omap1_usb1_init(unsigned nwires)
372{
373 u32 syscon1 = 0;
374
375 if (!cpu_is_omap15xx() && nwires != 6) {
376 u32 l;
377
378 l = omap_readl(USB_TRANSCEIVER_CTRL);
379 l &= ~CONF_USB1_UNI_R;
380 omap_writel(l, USB_TRANSCEIVER_CTRL);
381 }
382 if (nwires == 0)
383 return 0;
384
385 /* external transceiver */
386 omap_cfg_reg(USB1_TXD);
387 omap_cfg_reg(USB1_TXEN);
388 if (nwires != 3)
389 omap_cfg_reg(USB1_RCV);
390
391 if (cpu_is_omap15xx()) {
392 omap_cfg_reg(USB1_SEO);
393 omap_cfg_reg(USB1_SPEED);
394 // SUSP
395 } else if (cpu_is_omap1610() || cpu_is_omap5912()) {
396 omap_cfg_reg(W13_1610_USB1_SE0);
397 omap_cfg_reg(R13_1610_USB1_SPEED);
398 // SUSP
399 } else if (cpu_is_omap1710()) {
400 omap_cfg_reg(R13_1710_USB1_SE0);
401 // SUSP
402 } else {
403 pr_debug("usb%d cpu unrecognized\n", 1);
404 return 0;
405 }
406
407 switch (nwires) {
408 case 2:
409 goto bad;
410 case 3:
411 syscon1 = 2;
412 break;
413 case 4:
414 syscon1 = 1;
415 break;
416 case 6:
417 syscon1 = 3;
418 omap_cfg_reg(USB1_VP);
419 omap_cfg_reg(USB1_VM);
420 if (!cpu_is_omap15xx()) {
421 u32 l;
422
423 l = omap_readl(USB_TRANSCEIVER_CTRL);
424 l |= CONF_USB1_UNI_R;
425 omap_writel(l, USB_TRANSCEIVER_CTRL);
426 }
427 break;
428 default:
429bad:
430 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
431 1, nwires);
432 }
433
434 return syscon1 << 20;
435}
436
437static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
438{
439 u32 syscon1 = 0;
440
441 /* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
442 if (alt_pingroup || nwires == 0)
443 return 0;
444
445 if (!cpu_is_omap15xx() && nwires != 6) {
446 u32 l;
447
448 l = omap_readl(USB_TRANSCEIVER_CTRL);
449 l &= ~CONF_USB2_UNI_R;
450 omap_writel(l, USB_TRANSCEIVER_CTRL);
451 }
452
453 /* external transceiver */
454 if (cpu_is_omap15xx()) {
455 omap_cfg_reg(USB2_TXD);
456 omap_cfg_reg(USB2_TXEN);
457 omap_cfg_reg(USB2_SEO);
458 if (nwires != 3)
459 omap_cfg_reg(USB2_RCV);
460 /* there is no USB2_SPEED */
461 } else if (cpu_is_omap16xx()) {
462 omap_cfg_reg(V6_USB2_TXD);
463 omap_cfg_reg(W9_USB2_TXEN);
464 omap_cfg_reg(W5_USB2_SE0);
465 if (nwires != 3)
466 omap_cfg_reg(Y5_USB2_RCV);
467 // FIXME omap_cfg_reg(USB2_SPEED);
468 } else {
469 pr_debug("usb%d cpu unrecognized\n", 1);
470 return 0;
471 }
472
473 // omap_cfg_reg(USB2_SUSP);
474
475 switch (nwires) {
476 case 2:
477 goto bad;
478 case 3:
479 syscon1 = 2;
480 break;
481 case 4:
482 syscon1 = 1;
483 break;
484 case 5:
485 goto bad;
486 case 6:
487 syscon1 = 3;
488 if (cpu_is_omap15xx()) {
489 omap_cfg_reg(USB2_VP);
490 omap_cfg_reg(USB2_VM);
491 } else {
492 u32 l;
493
494 omap_cfg_reg(AA9_USB2_VP);
495 omap_cfg_reg(R9_USB2_VM);
496 l = omap_readl(USB_TRANSCEIVER_CTRL);
497 l |= CONF_USB2_UNI_R;
498 omap_writel(l, USB_TRANSCEIVER_CTRL);
499 }
500 break;
501 default:
502bad:
503 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
504 2, nwires);
505 }
506
507 return syscon1 << 24;
508}
509
510#ifdef CONFIG_ARCH_OMAP15XX
511/* OMAP-1510 OHCI has its own MMU for DMA */
512#define OMAP1510_LB_MEMSIZE 32 /* Should be same as SDRAM size */
513#define OMAP1510_LB_CLOCK_DIV 0xfffec10c
514#define OMAP1510_LB_MMU_CTL 0xfffec208
515#define OMAP1510_LB_MMU_LCK 0xfffec224
516#define OMAP1510_LB_MMU_LD_TLB 0xfffec228
517#define OMAP1510_LB_MMU_CAM_H 0xfffec22c
518#define OMAP1510_LB_MMU_CAM_L 0xfffec230
519#define OMAP1510_LB_MMU_RAM_H 0xfffec234
520#define OMAP1510_LB_MMU_RAM_L 0xfffec238
521
522/*
523 * Bus address is physical address, except for OMAP-1510 Local Bus.
524 * OMAP-1510 bus address is translated into a Local Bus address if the
525 * OMAP bus type is lbus.
526 */
527#define OMAP1510_LB_OFFSET UL(0x30000000)
528
529/*
530 * OMAP-1510 specific Local Bus clock on/off
531 */
532static int omap_1510_local_bus_power(int on)
533{
534 if (on) {
535 omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
536 udelay(200);
537 } else {
538 omap_writel(0, OMAP1510_LB_MMU_CTL);
539 }
540
541 return 0;
542}
543
544/*
545 * OMAP-1510 specific Local Bus initialization
546 * NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
547 * See also arch/mach-omap/memory.h for __virt_to_dma() and
548 * __dma_to_virt() which need to match with the physical
549 * Local Bus address below.
550 */
551static int omap_1510_local_bus_init(void)
552{
553 unsigned int tlb;
554 unsigned long lbaddr, physaddr;
555
556 omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
557 OMAP1510_LB_CLOCK_DIV);
558
559 /* Configure the Local Bus MMU table */
560 for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
561 lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
562 physaddr = tlb * 0x00100000 + PHYS_OFFSET;
563 omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
564 omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
565 OMAP1510_LB_MMU_CAM_L);
566 omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
567 omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
568 omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
569 omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
570 }
571
572 /* Enable the walking table */
573 omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
574 udelay(200);
575
576 return 0;
577}
578
579static void omap_1510_local_bus_reset(void)
580{
581 omap_1510_local_bus_power(1);
582 omap_1510_local_bus_init();
583}
584
585/* ULPD_DPLL_CTRL */
586#define DPLL_IOB (1 << 13)
587#define DPLL_PLL_ENABLE (1 << 4)
588#define DPLL_LOCK (1 << 0)
589
590/* ULPD_APLL_CTRL */
591#define APLL_NDPLL_SWITCH (1 << 0)
592
593static void __init omap_1510_usb_init(struct omap_usb_config *config)
594{
595 unsigned int val;
596 u16 w;
597
598 config->usb0_init(config->pins[0], is_usb0_device(config));
599 config->usb1_init(config->pins[1]);
600 config->usb2_init(config->pins[2], 0);
601
602 val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
603 val |= (config->hmc_mode << 1);
604 omap_writel(val, MOD_CONF_CTRL_0);
605
606 printk("USB: hmc %d", config->hmc_mode);
607 if (config->pins[0])
608 pr_cont(", usb0 %d wires%s", config->pins[0],
609 is_usb0_device(config) ? " (dev)" : "");
610 if (config->pins[1])
611 pr_cont(", usb1 %d wires", config->pins[1]);
612 if (config->pins[2])
613 pr_cont(", usb2 %d wires", config->pins[2]);
614 pr_cont("\n");
615
616 /* use DPLL for 48 MHz function clock */
617 pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
618 omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
619
620 w = omap_readw(ULPD_APLL_CTRL);
621 w &= ~APLL_NDPLL_SWITCH;
622 omap_writew(w, ULPD_APLL_CTRL);
623
624 w = omap_readw(ULPD_DPLL_CTRL);
625 w |= DPLL_IOB | DPLL_PLL_ENABLE;
626 omap_writew(w, ULPD_DPLL_CTRL);
627
628 w = omap_readw(ULPD_SOFT_REQ);
629 w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
630 omap_writew(w, ULPD_SOFT_REQ);
631
632 while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
633 cpu_relax();
634
635#if IS_ENABLED(CONFIG_USB_OMAP)
636 if (config->register_dev) {
637 int status;
638
639 udc_device.dev.platform_data = config;
640 status = platform_device_register(&udc_device);
641 if (status)
642 pr_debug("can't register UDC device, %d\n", status);
643 /* udc driver gates 48MHz by D+ pullup */
644 }
645#endif
646
647 if (IS_ENABLED(CONFIG_USB_OHCI_HCD) && config->register_host) {
648 int status;
649
650 ohci_device.dev.platform_data = config;
651 dma_direct_set_offset(&ohci_device.dev, PHYS_OFFSET,
652 OMAP1510_LB_OFFSET, (u64)-1);
653 status = platform_device_register(&ohci_device);
654 if (status)
655 pr_debug("can't register OHCI device, %d\n", status);
656 /* hcd explicitly gates 48MHz */
657
658 config->lb_reset = omap_1510_local_bus_reset;
659 }
660}
661
662#else
663static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
664#endif
665
666void __init omap1_usb_init(struct omap_usb_config *_pdata)
667{
668 struct omap_usb_config *pdata;
669
670 pdata = kmemdup(_pdata, sizeof(*pdata), GFP_KERNEL);
671 if (!pdata)
672 return;
673
674 pdata->usb0_init = omap1_usb0_init;
675 pdata->usb1_init = omap1_usb1_init;
676 pdata->usb2_init = omap1_usb2_init;
677 udc_device_init(pdata);
678 ohci_device_init(pdata);
679 otg_device_init(pdata);
680
681 if (cpu_is_omap16xx())
682 omap_otg_init(pdata);
683 else if (cpu_is_omap15xx())
684 omap_1510_usb_init(pdata);
685 else
686 printk(KERN_ERR "USB: No init for your chip yet\n");
687}
1/*
2 * Platform level USB initialization for FS USB OTG controller on omap1 and 24xx
3 *
4 * Copyright (C) 2004 Texas Instruments, Inc.
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
19 */
20
21#include <linux/module.h>
22#include <linux/kernel.h>
23#include <linux/init.h>
24#include <linux/platform_device.h>
25#include <linux/io.h>
26
27#include <asm/irq.h>
28
29#include <mach/mux.h>
30
31#include <mach/usb.h>
32
33#include "common.h"
34
35/* These routines should handle the standard chip-specific modes
36 * for usb0/1/2 ports, covering basic mux and transceiver setup.
37 *
38 * Some board-*.c files will need to set up additional mux options,
39 * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
40 */
41
42/* TESTED ON:
43 * - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
44 * - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
45 * - 5912 OSK UDC, with *nonstandard* A-to-A cable
46 * - 1510 Innovator UDC with bundled usb0 cable
47 * - 1510 Innovator OHCI with bundled usb1/usb2 cable
48 * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
49 * - 1710 custom development board using alternate pin group
50 * - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
51 */
52
53#define INT_USB_IRQ_GEN IH2_BASE + 20
54#define INT_USB_IRQ_NISO IH2_BASE + 30
55#define INT_USB_IRQ_ISO IH2_BASE + 29
56#define INT_USB_IRQ_HGEN INT_USB_HHC_1
57#define INT_USB_IRQ_OTG IH2_BASE + 8
58
59#ifdef CONFIG_ARCH_OMAP_OTG
60
61void __init
62omap_otg_init(struct omap_usb_config *config)
63{
64 u32 syscon;
65 int alt_pingroup = 0;
66
67 /* NOTE: no bus or clock setup (yet?) */
68
69 syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
70 if (!(syscon & OTG_RESET_DONE))
71 pr_debug("USB resets not complete?\n");
72
73 //omap_writew(0, OTG_IRQ_EN);
74
75 /* pin muxing and transceiver pinouts */
76 if (config->pins[0] > 2) /* alt pingroup 2 */
77 alt_pingroup = 1;
78 syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
79 syscon |= config->usb1_init(config->pins[1]);
80 syscon |= config->usb2_init(config->pins[2], alt_pingroup);
81 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
82 omap_writel(syscon, OTG_SYSCON_1);
83
84 syscon = config->hmc_mode;
85 syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
86#ifdef CONFIG_USB_OTG
87 if (config->otg)
88 syscon |= OTG_EN;
89#endif
90 if (cpu_class_is_omap1())
91 pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
92 omap_readl(USB_TRANSCEIVER_CTRL));
93 pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
94 omap_writel(syscon, OTG_SYSCON_2);
95
96 printk("USB: hmc %d", config->hmc_mode);
97 if (!alt_pingroup)
98 printk(", usb2 alt %d wires", config->pins[2]);
99 else if (config->pins[0])
100 printk(", usb0 %d wires%s", config->pins[0],
101 is_usb0_device(config) ? " (dev)" : "");
102 if (config->pins[1])
103 printk(", usb1 %d wires", config->pins[1]);
104 if (!alt_pingroup && config->pins[2])
105 printk(", usb2 %d wires", config->pins[2]);
106 if (config->otg)
107 printk(", Mini-AB on usb%d", config->otg - 1);
108 printk("\n");
109
110 if (cpu_class_is_omap1()) {
111 u16 w;
112
113 /* leave USB clocks/controllers off until needed */
114 w = omap_readw(ULPD_SOFT_REQ);
115 w &= ~SOFT_USB_CLK_REQ;
116 omap_writew(w, ULPD_SOFT_REQ);
117
118 w = omap_readw(ULPD_CLOCK_CTRL);
119 w &= ~USB_MCLK_EN;
120 w |= DIS_USB_PVCI_CLK;
121 omap_writew(w, ULPD_CLOCK_CTRL);
122 }
123 syscon = omap_readl(OTG_SYSCON_1);
124 syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
125
126#if IS_ENABLED(CONFIG_USB_OMAP)
127 if (config->otg || config->register_dev) {
128 struct platform_device *udc_device = config->udc_device;
129 int status;
130
131 syscon &= ~DEV_IDLE_EN;
132 udc_device->dev.platform_data = config;
133 status = platform_device_register(udc_device);
134 if (status)
135 pr_debug("can't register UDC device, %d\n", status);
136 }
137#endif
138
139#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
140 if (config->otg || config->register_host) {
141 struct platform_device *ohci_device = config->ohci_device;
142 int status;
143
144 syscon &= ~HST_IDLE_EN;
145 ohci_device->dev.platform_data = config;
146 status = platform_device_register(ohci_device);
147 if (status)
148 pr_debug("can't register OHCI device, %d\n", status);
149 }
150#endif
151
152#ifdef CONFIG_USB_OTG
153 if (config->otg) {
154 struct platform_device *otg_device = config->otg_device;
155 int status;
156
157 syscon &= ~OTG_IDLE_EN;
158 otg_device->dev.platform_data = config;
159 status = platform_device_register(otg_device);
160 if (status)
161 pr_debug("can't register OTG device, %d\n", status);
162 }
163#endif
164 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
165 omap_writel(syscon, OTG_SYSCON_1);
166}
167
168#else
169void omap_otg_init(struct omap_usb_config *config) {}
170#endif
171
172#if IS_ENABLED(CONFIG_USB_OMAP)
173
174static struct resource udc_resources[] = {
175 /* order is significant! */
176 { /* registers */
177 .start = UDC_BASE,
178 .end = UDC_BASE + 0xff,
179 .flags = IORESOURCE_MEM,
180 }, { /* general IRQ */
181 .start = INT_USB_IRQ_GEN,
182 .flags = IORESOURCE_IRQ,
183 }, { /* PIO IRQ */
184 .start = INT_USB_IRQ_NISO,
185 .flags = IORESOURCE_IRQ,
186 }, { /* SOF IRQ */
187 .start = INT_USB_IRQ_ISO,
188 .flags = IORESOURCE_IRQ,
189 },
190};
191
192static u64 udc_dmamask = ~(u32)0;
193
194static struct platform_device udc_device = {
195 .name = "omap_udc",
196 .id = -1,
197 .dev = {
198 .dma_mask = &udc_dmamask,
199 .coherent_dma_mask = 0xffffffff,
200 },
201 .num_resources = ARRAY_SIZE(udc_resources),
202 .resource = udc_resources,
203};
204
205static inline void udc_device_init(struct omap_usb_config *pdata)
206{
207 /* IRQ numbers for omap7xx */
208 if(cpu_is_omap7xx()) {
209 udc_resources[1].start = INT_7XX_USB_GENI;
210 udc_resources[2].start = INT_7XX_USB_NON_ISO;
211 udc_resources[3].start = INT_7XX_USB_ISO;
212 }
213 pdata->udc_device = &udc_device;
214}
215
216#else
217
218static inline void udc_device_init(struct omap_usb_config *pdata)
219{
220}
221
222#endif
223
224#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
225
226/* The dmamask must be set for OHCI to work */
227static u64 ohci_dmamask = ~(u32)0;
228
229static struct resource ohci_resources[] = {
230 {
231 .start = OMAP_OHCI_BASE,
232 .end = OMAP_OHCI_BASE + 0xff,
233 .flags = IORESOURCE_MEM,
234 },
235 {
236 .start = INT_USB_IRQ_HGEN,
237 .flags = IORESOURCE_IRQ,
238 },
239};
240
241static struct platform_device ohci_device = {
242 .name = "ohci",
243 .id = -1,
244 .dev = {
245 .dma_mask = &ohci_dmamask,
246 .coherent_dma_mask = 0xffffffff,
247 },
248 .num_resources = ARRAY_SIZE(ohci_resources),
249 .resource = ohci_resources,
250};
251
252static inline void ohci_device_init(struct omap_usb_config *pdata)
253{
254 if (cpu_is_omap7xx())
255 ohci_resources[1].start = INT_7XX_USB_HHC_1;
256 pdata->ohci_device = &ohci_device;
257 pdata->ocpi_enable = &ocpi_enable;
258}
259
260#else
261
262static inline void ohci_device_init(struct omap_usb_config *pdata)
263{
264}
265
266#endif
267
268#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
269
270static struct resource otg_resources[] = {
271 /* order is significant! */
272 {
273 .start = OTG_BASE,
274 .end = OTG_BASE + 0xff,
275 .flags = IORESOURCE_MEM,
276 }, {
277 .start = INT_USB_IRQ_OTG,
278 .flags = IORESOURCE_IRQ,
279 },
280};
281
282static struct platform_device otg_device = {
283 .name = "omap_otg",
284 .id = -1,
285 .num_resources = ARRAY_SIZE(otg_resources),
286 .resource = otg_resources,
287};
288
289static inline void otg_device_init(struct omap_usb_config *pdata)
290{
291 if (cpu_is_omap7xx())
292 otg_resources[1].start = INT_7XX_USB_OTG;
293 pdata->otg_device = &otg_device;
294}
295
296#else
297
298static inline void otg_device_init(struct omap_usb_config *pdata)
299{
300}
301
302#endif
303
304static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
305{
306 u32 syscon1 = 0;
307
308 if (nwires == 0) {
309 if (!cpu_is_omap15xx()) {
310 u32 l;
311
312 /* pulldown D+/D- */
313 l = omap_readl(USB_TRANSCEIVER_CTRL);
314 l &= ~(3 << 1);
315 omap_writel(l, USB_TRANSCEIVER_CTRL);
316 }
317 return 0;
318 }
319
320 if (is_device) {
321 if (cpu_is_omap7xx()) {
322 omap_cfg_reg(AA17_7XX_USB_DM);
323 omap_cfg_reg(W16_7XX_USB_PU_EN);
324 omap_cfg_reg(W17_7XX_USB_VBUSI);
325 omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
326 omap_cfg_reg(W19_7XX_USB_DCRST);
327 } else
328 omap_cfg_reg(W4_USB_PUEN);
329 }
330
331 if (nwires == 2) {
332 u32 l;
333
334 // omap_cfg_reg(P9_USB_DP);
335 // omap_cfg_reg(R8_USB_DM);
336
337 if (cpu_is_omap15xx()) {
338 /* This works on 1510-Innovator */
339 return 0;
340 }
341
342 /* NOTES:
343 * - peripheral should configure VBUS detection!
344 * - only peripherals may use the internal D+/D- pulldowns
345 * - OTG support on this port not yet written
346 */
347
348 /* Don't do this for omap7xx -- it causes USB to not work correctly */
349 if (!cpu_is_omap7xx()) {
350 l = omap_readl(USB_TRANSCEIVER_CTRL);
351 l &= ~(7 << 4);
352 if (!is_device)
353 l |= (3 << 1);
354 omap_writel(l, USB_TRANSCEIVER_CTRL);
355 }
356
357 return 3 << 16;
358 }
359
360 /* alternate pin config, external transceiver */
361 if (cpu_is_omap15xx()) {
362 printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
363 return 0;
364 }
365
366 omap_cfg_reg(V6_USB0_TXD);
367 omap_cfg_reg(W9_USB0_TXEN);
368 omap_cfg_reg(W5_USB0_SE0);
369 if (nwires != 3)
370 omap_cfg_reg(Y5_USB0_RCV);
371
372 /* NOTE: SPEED and SUSP aren't configured here. OTG hosts
373 * may be able to use I2C requests to set those bits along
374 * with VBUS switching and overcurrent detection.
375 */
376
377 if (nwires != 6) {
378 u32 l;
379
380 l = omap_readl(USB_TRANSCEIVER_CTRL);
381 l &= ~CONF_USB2_UNI_R;
382 omap_writel(l, USB_TRANSCEIVER_CTRL);
383 }
384
385 switch (nwires) {
386 case 3:
387 syscon1 = 2;
388 break;
389 case 4:
390 syscon1 = 1;
391 break;
392 case 6:
393 syscon1 = 3;
394 {
395 u32 l;
396
397 omap_cfg_reg(AA9_USB0_VP);
398 omap_cfg_reg(R9_USB0_VM);
399 l = omap_readl(USB_TRANSCEIVER_CTRL);
400 l |= CONF_USB2_UNI_R;
401 omap_writel(l, USB_TRANSCEIVER_CTRL);
402 }
403 break;
404 default:
405 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
406 0, nwires);
407 }
408
409 return syscon1 << 16;
410}
411
412static u32 __init omap1_usb1_init(unsigned nwires)
413{
414 u32 syscon1 = 0;
415
416 if (!cpu_is_omap15xx() && nwires != 6) {
417 u32 l;
418
419 l = omap_readl(USB_TRANSCEIVER_CTRL);
420 l &= ~CONF_USB1_UNI_R;
421 omap_writel(l, USB_TRANSCEIVER_CTRL);
422 }
423 if (nwires == 0)
424 return 0;
425
426 /* external transceiver */
427 omap_cfg_reg(USB1_TXD);
428 omap_cfg_reg(USB1_TXEN);
429 if (nwires != 3)
430 omap_cfg_reg(USB1_RCV);
431
432 if (cpu_is_omap15xx()) {
433 omap_cfg_reg(USB1_SEO);
434 omap_cfg_reg(USB1_SPEED);
435 // SUSP
436 } else if (cpu_is_omap1610() || cpu_is_omap5912()) {
437 omap_cfg_reg(W13_1610_USB1_SE0);
438 omap_cfg_reg(R13_1610_USB1_SPEED);
439 // SUSP
440 } else if (cpu_is_omap1710()) {
441 omap_cfg_reg(R13_1710_USB1_SE0);
442 // SUSP
443 } else {
444 pr_debug("usb%d cpu unrecognized\n", 1);
445 return 0;
446 }
447
448 switch (nwires) {
449 case 2:
450 goto bad;
451 case 3:
452 syscon1 = 2;
453 break;
454 case 4:
455 syscon1 = 1;
456 break;
457 case 6:
458 syscon1 = 3;
459 omap_cfg_reg(USB1_VP);
460 omap_cfg_reg(USB1_VM);
461 if (!cpu_is_omap15xx()) {
462 u32 l;
463
464 l = omap_readl(USB_TRANSCEIVER_CTRL);
465 l |= CONF_USB1_UNI_R;
466 omap_writel(l, USB_TRANSCEIVER_CTRL);
467 }
468 break;
469 default:
470bad:
471 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
472 1, nwires);
473 }
474
475 return syscon1 << 20;
476}
477
478static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
479{
480 u32 syscon1 = 0;
481
482 /* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
483 if (alt_pingroup || nwires == 0)
484 return 0;
485
486 if (!cpu_is_omap15xx() && nwires != 6) {
487 u32 l;
488
489 l = omap_readl(USB_TRANSCEIVER_CTRL);
490 l &= ~CONF_USB2_UNI_R;
491 omap_writel(l, USB_TRANSCEIVER_CTRL);
492 }
493
494 /* external transceiver */
495 if (cpu_is_omap15xx()) {
496 omap_cfg_reg(USB2_TXD);
497 omap_cfg_reg(USB2_TXEN);
498 omap_cfg_reg(USB2_SEO);
499 if (nwires != 3)
500 omap_cfg_reg(USB2_RCV);
501 /* there is no USB2_SPEED */
502 } else if (cpu_is_omap16xx()) {
503 omap_cfg_reg(V6_USB2_TXD);
504 omap_cfg_reg(W9_USB2_TXEN);
505 omap_cfg_reg(W5_USB2_SE0);
506 if (nwires != 3)
507 omap_cfg_reg(Y5_USB2_RCV);
508 // FIXME omap_cfg_reg(USB2_SPEED);
509 } else {
510 pr_debug("usb%d cpu unrecognized\n", 1);
511 return 0;
512 }
513
514 // omap_cfg_reg(USB2_SUSP);
515
516 switch (nwires) {
517 case 2:
518 goto bad;
519 case 3:
520 syscon1 = 2;
521 break;
522 case 4:
523 syscon1 = 1;
524 break;
525 case 5:
526 goto bad;
527 case 6:
528 syscon1 = 3;
529 if (cpu_is_omap15xx()) {
530 omap_cfg_reg(USB2_VP);
531 omap_cfg_reg(USB2_VM);
532 } else {
533 u32 l;
534
535 omap_cfg_reg(AA9_USB2_VP);
536 omap_cfg_reg(R9_USB2_VM);
537 l = omap_readl(USB_TRANSCEIVER_CTRL);
538 l |= CONF_USB2_UNI_R;
539 omap_writel(l, USB_TRANSCEIVER_CTRL);
540 }
541 break;
542 default:
543bad:
544 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
545 2, nwires);
546 }
547
548 return syscon1 << 24;
549}
550
551#ifdef CONFIG_ARCH_OMAP15XX
552
553/* ULPD_DPLL_CTRL */
554#define DPLL_IOB (1 << 13)
555#define DPLL_PLL_ENABLE (1 << 4)
556#define DPLL_LOCK (1 << 0)
557
558/* ULPD_APLL_CTRL */
559#define APLL_NDPLL_SWITCH (1 << 0)
560
561static void __init omap_1510_usb_init(struct omap_usb_config *config)
562{
563 unsigned int val;
564 u16 w;
565
566 config->usb0_init(config->pins[0], is_usb0_device(config));
567 config->usb1_init(config->pins[1]);
568 config->usb2_init(config->pins[2], 0);
569
570 val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
571 val |= (config->hmc_mode << 1);
572 omap_writel(val, MOD_CONF_CTRL_0);
573
574 printk("USB: hmc %d", config->hmc_mode);
575 if (config->pins[0])
576 printk(", usb0 %d wires%s", config->pins[0],
577 is_usb0_device(config) ? " (dev)" : "");
578 if (config->pins[1])
579 printk(", usb1 %d wires", config->pins[1]);
580 if (config->pins[2])
581 printk(", usb2 %d wires", config->pins[2]);
582 printk("\n");
583
584 /* use DPLL for 48 MHz function clock */
585 pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
586 omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
587
588 w = omap_readw(ULPD_APLL_CTRL);
589 w &= ~APLL_NDPLL_SWITCH;
590 omap_writew(w, ULPD_APLL_CTRL);
591
592 w = omap_readw(ULPD_DPLL_CTRL);
593 w |= DPLL_IOB | DPLL_PLL_ENABLE;
594 omap_writew(w, ULPD_DPLL_CTRL);
595
596 w = omap_readw(ULPD_SOFT_REQ);
597 w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
598 omap_writew(w, ULPD_SOFT_REQ);
599
600 while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
601 cpu_relax();
602
603#if IS_ENABLED(CONFIG_USB_OMAP)
604 if (config->register_dev) {
605 int status;
606
607 udc_device.dev.platform_data = config;
608 status = platform_device_register(&udc_device);
609 if (status)
610 pr_debug("can't register UDC device, %d\n", status);
611 /* udc driver gates 48MHz by D+ pullup */
612 }
613#endif
614
615#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
616 if (config->register_host) {
617 int status;
618
619 ohci_device.dev.platform_data = config;
620 status = platform_device_register(&ohci_device);
621 if (status)
622 pr_debug("can't register OHCI device, %d\n", status);
623 /* hcd explicitly gates 48MHz */
624 }
625#endif
626}
627
628#else
629static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
630#endif
631
632void __init omap1_usb_init(struct omap_usb_config *_pdata)
633{
634 struct omap_usb_config *pdata;
635
636 pdata = kmemdup(_pdata, sizeof(*pdata), GFP_KERNEL);
637 if (!pdata)
638 return;
639
640 pdata->usb0_init = omap1_usb0_init;
641 pdata->usb1_init = omap1_usb1_init;
642 pdata->usb2_init = omap1_usb2_init;
643 udc_device_init(pdata);
644 ohci_device_init(pdata);
645 otg_device_init(pdata);
646
647 if (cpu_is_omap7xx() || cpu_is_omap16xx())
648 omap_otg_init(pdata);
649 else if (cpu_is_omap15xx())
650 omap_1510_usb_init(pdata);
651 else
652 printk(KERN_ERR "USB: No init for your chip yet\n");
653}