1# SPDX-License-Identifier: GPL-2.0
  2#
  3# Physical Layer USB driver configuration
  4#
  5menu "USB Physical Layer drivers"
  6
  7config USB_PHY
  8	select EXTCON
  9	def_bool n
 10
 11#
 12# USB Transceiver Drivers
 13#
 14config AB8500_USB
 15	tristate "AB8500 USB Transceiver Driver"
 16	depends on AB8500_CORE
 17	select USB_PHY
 18	help
 19	  Enable this to support the USB OTG transceiver in AB8500 chip.
 20	  This transceiver supports high and full speed devices plus,
 21	  in host mode, low speed.
 22
 23config FSL_USB2_OTG
 24	tristate "Freescale USB OTG Transceiver Driver"
 25	depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM=y && PM
 26	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 27	select USB_PHY
 28	help
 29	  Enable this to support Freescale USB OTG transceiver.
 30
 31config ISP1301_OMAP
 32	tristate "Philips ISP1301 with OMAP OTG"
 33	depends on I2C && ARCH_OMAP_OTG
 34	depends on USB
 35	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 36	select USB_PHY
 37	help
 38	  If you say yes here you get support for the Philips ISP1301
 39	  USB-On-The-Go transceiver working with the OMAP OTG controller.
 40	  The ISP1301 is a full speed USB  transceiver which is used in
 41	  products including H2, H3, and H4 development boards for Texas
 42	  Instruments OMAP processors.
 43
 44	  This driver can also be built as a module.  If so, the module
 45	  will be called phy-isp1301-omap.
 46
 47config KEYSTONE_USB_PHY
 48	tristate "Keystone USB PHY Driver"
 49	depends on ARCH_KEYSTONE || COMPILE_TEST
 50	depends on NOP_USB_XCEIV
 51	help
 52	  Enable this to support Keystone USB phy. This driver provides
 53	  interface to interact with USB 2.0 and USB 3.0 PHY that is part
 54	  of the Keystone SOC.
 55
 56config NOP_USB_XCEIV
 57	tristate "NOP USB Transceiver Driver"
 58	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
 59	select USB_PHY
 60	help
 61	  This driver is to be used by all the usb transceiver which are either
 62	  built-in with usb ip or which are autonomous and doesn't require any
 63	  phy programming such as ISP1x04 etc.
 64
 65config AM335X_CONTROL_USB
 66	tristate
 67
 68config AM335X_PHY_USB
 69	tristate "AM335x USB PHY Driver"
 70	depends on ARM || COMPILE_TEST
 71	depends on NOP_USB_XCEIV
 72	select USB_PHY
 73	select AM335X_CONTROL_USB
 74	select USB_COMMON
 75	help
 76	  This driver provides PHY support for that phy which part for the
 77	  AM335x SoC.
 78
 79config TWL6030_USB
 80	tristate "TWL6030 USB Transceiver Driver"
 81	depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
 82	depends on OF
 83	help
 84	  Enable this to support the USB OTG transceiver on TWL6030
 85	  family chips. This TWL6030 transceiver has the VBUS and ID GND
 86	  and OTG SRP events capabilities. For all other transceiver functionality
 87	  UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
 88	  are hooked to this driver through platform_data structure.
 89	  The definition of internal PHY APIs are in the mach-omap2 layer.
 90
 91config USB_GPIO_VBUS
 92	tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
 93	depends on GPIOLIB || COMPILE_TEST
 94	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 
 95	select USB_PHY
 96	help
 97	  Provides simple GPIO VBUS sensing for controllers with an
 98	  internal transceiver via the usb_phy interface, and
 99	  optionally control of a D+ pullup GPIO as well as a VBUS
100	  current limit regulator.
 
 
 
101
102config OMAP_OTG
103	tristate "OMAP USB OTG controller driver"
104	depends on ARCH_OMAP_OTG && EXTCON
105	help
106	  Enable this to support some transceivers on OMAP1 platforms. OTG
107	  controller is needed to switch between host and peripheral modes.
108
109	  This driver can also be built as a module. If so, the module
110	  will be called phy-omap-otg.
111
112config TAHVO_USB
113	tristate "Tahvo USB transceiver driver"
114	depends on MFD_RETU
115	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
116	select USB_PHY
117	help
118	  Enable this to support USB transceiver on Tahvo. This is used
119	  at least on Nokia 770.
120
121config TAHVO_USB_HOST_BY_DEFAULT
122	depends on TAHVO_USB
123	bool "Device in USB host mode by default"
124	help
125	  Say Y here, if you want the device to enter USB host mode
126	  by default on bootup.
127
128config USB_ISP1301
129	tristate "NXP ISP1301 USB transceiver support"
130	depends on USB || USB_GADGET
131	depends on I2C
132	select USB_PHY
133	help
134	  Say Y here to add support for the NXP ISP1301 USB transceiver driver.
135	  This chip is typically used as USB transceiver for USB host, gadget
136	  and OTG drivers (to be selected separately).
137
138	  To compile this driver as a module, choose M here: the
139	  module will be called phy-isp1301.
140
141config USB_MV_OTG
142	tristate "Marvell USB OTG support"
143	depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
144	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
145	select USB_PHY
146	help
147	  Say Y here if you want to build Marvell USB OTG transciever
148	  driver in kernel (including PXA and MMP series). This driver
149	  implements role switch between EHCI host driver and gadget driver.
150
151	  To compile this driver as a module, choose M here.
152
153config USB_MXS_PHY
154	tristate "Freescale MXS USB PHY support"
155	depends on ARCH_MXC || ARCH_MXS
156	select STMP_DEVICE
157	select USB_PHY
158	help
159	  Enable this to support the Freescale MXS USB PHY.
160
161	  MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
162
163config USB_TEGRA_PHY
164	tristate "NVIDIA Tegra USB PHY Driver"
165	depends on ARCH_TEGRA || COMPILE_TEST
166	select USB_COMMON
167	select USB_PHY
168	select USB_ULPI
169	help
170	  This driver provides PHY support for the USB controllers found
171	  on NVIDIA Tegra SoC's.
172
173config USB_ULPI
174	bool "Generic ULPI Transceiver Driver"
175	depends on ARM || ARM64 || COMPILE_TEST
176	select USB_ULPI_VIEWPORT
177	help
178	  Enable this to support ULPI connected USB OTG transceivers which
179	  are likely found on embedded boards.
180
181config USB_ULPI_VIEWPORT
182	bool
183	help
184	  Provides read/write operations to the ULPI phy register set for
185	  controllers with a viewport register (e.g. Chipidea/ARC controllers).
186
187config JZ4770_PHY
188	tristate "Ingenic SoCs Transceiver Driver"
189	depends on MIPS || COMPILE_TEST
190	select USB_PHY
191	help
192	  This driver provides PHY support for the USB controller found
193	  on the JZ-series and X-series SoCs from Ingenic.
194
195endmenu

  1# SPDX-License-Identifier: GPL-2.0
  2#
  3# Physical Layer USB driver configuration
  4#
  5menu "USB Physical Layer drivers"
  6
  7config USB_PHY
  8	select EXTCON
  9	def_bool n
 10
 11#
 12# USB Transceiver Drivers
 13#
 14config AB8500_USB
 15	tristate "AB8500 USB Transceiver Driver"
 16	depends on AB8500_CORE
 17	select USB_PHY
 18	help
 19	  Enable this to support the USB OTG transceiver in AB8500 chip.
 20	  This transceiver supports high and full speed devices plus,
 21	  in host mode, low speed.
 22
 23config FSL_USB2_OTG
 24	tristate "Freescale USB OTG Transceiver Driver"
 25	depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM=y && PM
 26	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 27	select USB_PHY
 28	help
 29	  Enable this to support Freescale USB OTG transceiver.
 30
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 31config KEYSTONE_USB_PHY
 32	tristate "Keystone USB PHY Driver"
 33	depends on ARCH_KEYSTONE || COMPILE_TEST
 34	depends on NOP_USB_XCEIV
 35	help
 36	  Enable this to support Keystone USB phy. This driver provides
 37	  interface to interact with USB 2.0 and USB 3.0 PHY that is part
 38	  of the Keystone SOC.
 39
 40config NOP_USB_XCEIV
 41	tristate "NOP USB Transceiver Driver"
 42	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
 43	select USB_PHY
 44	help
 45	  This driver is to be used by all the usb transceiver which are either
 46	  built-in with usb ip or which are autonomous and doesn't require any
 47	  phy programming such as ISP1x04 etc.
 48
 49config AM335X_CONTROL_USB
 50	tristate
 51
 52config AM335X_PHY_USB
 53	tristate "AM335x USB PHY Driver"
 54	depends on ARM || COMPILE_TEST
 55	depends on NOP_USB_XCEIV
 56	select USB_PHY
 57	select AM335X_CONTROL_USB
 58	select USB_COMMON
 59	help
 60	  This driver provides PHY support for that phy which part for the
 61	  AM335x SoC.
 62
 63config TWL6030_USB
 64	tristate "TWL6030 USB Transceiver Driver"
 65	depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
 66	depends on OF
 67	help
 68	  Enable this to support the USB OTG transceiver on TWL6030
 69	  family chips. This TWL6030 transceiver has the VBUS and ID GND
 70	  and OTG SRP events capabilities. For all other transceiver functionality
 71	  UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
 72	  are hooked to this driver through platform_data structure.
 73	  The definition of internal PHY APIs are in the mach-omap2 layer.
 74
 75config USB_GPIO_VBUS
 76	tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
 77	depends on GPIOLIB || COMPILE_TEST
 78	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 79	depends on !USB_CONN_GPIO
 80	select USB_PHY
 81	help
 82	  Provides simple GPIO VBUS sensing for controllers with an
 83	  internal transceiver via the usb_phy interface, and
 84	  optionally control of a D+ pullup GPIO as well as a VBUS
 85	  current limit regulator. This driver is for devices that do
 86	  NOT support role switch. OTG devices that can do role switch
 87	  (master/peripheral) shall use the USB based connection
 88	  detection driver USB_CONN_GPIO.
 89
 90config OMAP_OTG
 91	tristate "OMAP USB OTG controller driver"
 92	depends on ARCH_OMAP_OTG && EXTCON
 93	help
 94	  Enable this to support some transceivers on OMAP1 platforms. OTG
 95	  controller is needed to switch between host and peripheral modes.
 96
 97	  This driver can also be built as a module. If so, the module
 98	  will be called phy-omap-otg.
 99
100config TAHVO_USB
101	tristate "Tahvo USB transceiver driver"
102	depends on MFD_RETU
103	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
104	select USB_PHY
105	help
106	  Enable this to support USB transceiver on Tahvo. This is used
107	  at least on Nokia 770.
108
109config TAHVO_USB_HOST_BY_DEFAULT
110	depends on TAHVO_USB
111	bool "Device in USB host mode by default"
112	help
113	  Say Y here, if you want the device to enter USB host mode
114	  by default on bootup.
115
116config USB_ISP1301
117	tristate "NXP ISP1301 USB transceiver support"
118	depends on USB || USB_GADGET
119	depends on I2C
120	select USB_PHY
121	help
122	  Say Y here to add support for the NXP ISP1301 USB transceiver driver.
123	  This chip is typically used as USB transceiver for USB host, gadget
124	  and OTG drivers (to be selected separately).
125
126	  To compile this driver as a module, choose M here: the
127	  module will be called phy-isp1301.
128
129config USB_MV_OTG
130	tristate "Marvell USB OTG support"
131	depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
132	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
133	select USB_PHY
134	help
135	  Say Y here if you want to build Marvell USB OTG transceiver
136	  driver in kernel (including PXA and MMP series). This driver
137	  implements role switch between EHCI host driver and gadget driver.
138
139	  To compile this driver as a module, choose M here.
140
141config USB_MXS_PHY
142	tristate "Freescale MXS USB PHY support"
143	depends on ARCH_MXC || ARCH_MXS
144	select STMP_DEVICE
145	select USB_PHY
146	help
147	  Enable this to support the Freescale MXS USB PHY.
148
149	  MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
150
151config USB_TEGRA_PHY
152	tristate "NVIDIA Tegra USB PHY Driver"
153	depends on ARCH_TEGRA || COMPILE_TEST
154	select USB_COMMON
155	select USB_PHY
156	select USB_ULPI
157	help
158	  This driver provides PHY support for the USB controllers found
159	  on NVIDIA Tegra SoC's.
160
161config USB_ULPI
162	bool "Generic ULPI Transceiver Driver"
163	depends on ARM || ARM64 || COMPILE_TEST
164	select USB_ULPI_VIEWPORT
165	help
166	  Enable this to support ULPI connected USB OTG transceivers which
167	  are likely found on embedded boards.
168
169config USB_ULPI_VIEWPORT
170	bool
171	help
172	  Provides read/write operations to the ULPI phy register set for
173	  controllers with a viewport register (e.g. Chipidea/ARC controllers).
 
 
 
 
 
 
 
 
174
175endmenu