Loading...
1# SPDX-License-Identifier: GPL-2.0
2#
3# Physical Layer USB driver configuration
4#
5menu "USB Physical Layer drivers"
6
7config USB_PHY
8 select EXTCON
9 def_bool n
10
11#
12# USB Transceiver Drivers
13#
14config AB8500_USB
15 tristate "AB8500 USB Transceiver Driver"
16 depends on AB8500_CORE
17 select USB_PHY
18 help
19 Enable this to support the USB OTG transceiver in AB8500 chip.
20 This transceiver supports high and full speed devices plus,
21 in host mode, low speed.
22
23config FSL_USB2_OTG
24 tristate "Freescale USB OTG Transceiver Driver"
25 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM=y && PM
26 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
27 select USB_PHY
28 help
29 Enable this to support Freescale USB OTG transceiver.
30
31config ISP1301_OMAP
32 tristate "Philips ISP1301 with OMAP OTG"
33 depends on I2C && ARCH_OMAP_OTG
34 depends on USB
35 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
36 select USB_PHY
37 help
38 If you say yes here you get support for the Philips ISP1301
39 USB-On-The-Go transceiver working with the OMAP OTG controller.
40 The ISP1301 is a full speed USB transceiver which is used in
41 products including H2, H3, and H4 development boards for Texas
42 Instruments OMAP processors.
43
44 This driver can also be built as a module. If so, the module
45 will be called phy-isp1301-omap.
46
47config KEYSTONE_USB_PHY
48 tristate "Keystone USB PHY Driver"
49 depends on ARCH_KEYSTONE || COMPILE_TEST
50 depends on NOP_USB_XCEIV
51 help
52 Enable this to support Keystone USB phy. This driver provides
53 interface to interact with USB 2.0 and USB 3.0 PHY that is part
54 of the Keystone SOC.
55
56config NOP_USB_XCEIV
57 tristate "NOP USB Transceiver Driver"
58 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
59 select USB_PHY
60 help
61 This driver is to be used by all the usb transceiver which are either
62 built-in with usb ip or which are autonomous and doesn't require any
63 phy programming such as ISP1x04 etc.
64
65config AM335X_CONTROL_USB
66 tristate
67
68config AM335X_PHY_USB
69 tristate "AM335x USB PHY Driver"
70 depends on ARM || COMPILE_TEST
71 depends on NOP_USB_XCEIV
72 select USB_PHY
73 select AM335X_CONTROL_USB
74 select USB_COMMON
75 help
76 This driver provides PHY support for that phy which part for the
77 AM335x SoC.
78
79config TWL6030_USB
80 tristate "TWL6030 USB Transceiver Driver"
81 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
82 depends on OF
83 help
84 Enable this to support the USB OTG transceiver on TWL6030
85 family chips. This TWL6030 transceiver has the VBUS and ID GND
86 and OTG SRP events capabilities. For all other transceiver functionality
87 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
88 are hooked to this driver through platform_data structure.
89 The definition of internal PHY APIs are in the mach-omap2 layer.
90
91config USB_GPIO_VBUS
92 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
93 depends on GPIOLIB || COMPILE_TEST
94 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
95 select USB_PHY
96 help
97 Provides simple GPIO VBUS sensing for controllers with an
98 internal transceiver via the usb_phy interface, and
99 optionally control of a D+ pullup GPIO as well as a VBUS
100 current limit regulator.
101
102config OMAP_OTG
103 tristate "OMAP USB OTG controller driver"
104 depends on ARCH_OMAP_OTG && EXTCON
105 help
106 Enable this to support some transceivers on OMAP1 platforms. OTG
107 controller is needed to switch between host and peripheral modes.
108
109 This driver can also be built as a module. If so, the module
110 will be called phy-omap-otg.
111
112config TAHVO_USB
113 tristate "Tahvo USB transceiver driver"
114 depends on MFD_RETU
115 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
116 select USB_PHY
117 help
118 Enable this to support USB transceiver on Tahvo. This is used
119 at least on Nokia 770.
120
121config TAHVO_USB_HOST_BY_DEFAULT
122 depends on TAHVO_USB
123 bool "Device in USB host mode by default"
124 help
125 Say Y here, if you want the device to enter USB host mode
126 by default on bootup.
127
128config USB_ISP1301
129 tristate "NXP ISP1301 USB transceiver support"
130 depends on USB || USB_GADGET
131 depends on I2C
132 select USB_PHY
133 help
134 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
135 This chip is typically used as USB transceiver for USB host, gadget
136 and OTG drivers (to be selected separately).
137
138 To compile this driver as a module, choose M here: the
139 module will be called phy-isp1301.
140
141config USB_MV_OTG
142 tristate "Marvell USB OTG support"
143 depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
144 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
145 select USB_PHY
146 help
147 Say Y here if you want to build Marvell USB OTG transciever
148 driver in kernel (including PXA and MMP series). This driver
149 implements role switch between EHCI host driver and gadget driver.
150
151 To compile this driver as a module, choose M here.
152
153config USB_MXS_PHY
154 tristate "Freescale MXS USB PHY support"
155 depends on ARCH_MXC || ARCH_MXS
156 select STMP_DEVICE
157 select USB_PHY
158 help
159 Enable this to support the Freescale MXS USB PHY.
160
161 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
162
163config USB_TEGRA_PHY
164 tristate "NVIDIA Tegra USB PHY Driver"
165 depends on ARCH_TEGRA || COMPILE_TEST
166 select USB_COMMON
167 select USB_PHY
168 select USB_ULPI
169 help
170 This driver provides PHY support for the USB controllers found
171 on NVIDIA Tegra SoC's.
172
173config USB_ULPI
174 bool "Generic ULPI Transceiver Driver"
175 depends on ARM || ARM64 || COMPILE_TEST
176 select USB_ULPI_VIEWPORT
177 help
178 Enable this to support ULPI connected USB OTG transceivers which
179 are likely found on embedded boards.
180
181config USB_ULPI_VIEWPORT
182 bool
183 help
184 Provides read/write operations to the ULPI phy register set for
185 controllers with a viewport register (e.g. Chipidea/ARC controllers).
186
187config JZ4770_PHY
188 tristate "Ingenic SoCs Transceiver Driver"
189 depends on MIPS || COMPILE_TEST
190 select USB_PHY
191 help
192 This driver provides PHY support for the USB controller found
193 on the JZ-series and X-series SoCs from Ingenic.
194
195endmenu
1#
2# Physical Layer USB driver configuration
3#
4menu "USB Physical Layer drivers"
5
6config USB_PHY
7 def_bool n
8
9#
10# USB Transceiver Drivers
11#
12config AB8500_USB
13 tristate "AB8500 USB Transceiver Driver"
14 depends on AB8500_CORE
15 select USB_PHY
16 help
17 Enable this to support the USB OTG transceiver in AB8500 chip.
18 This transceiver supports high and full speed devices plus,
19 in host mode, low speed.
20
21config FSL_USB2_OTG
22 bool "Freescale USB OTG Transceiver Driver"
23 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
24 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
25 select USB_PHY
26 help
27 Enable this to support Freescale USB OTG transceiver.
28
29config ISP1301_OMAP
30 tristate "Philips ISP1301 with OMAP OTG"
31 depends on I2C && ARCH_OMAP_OTG
32 depends on USB
33 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
34 select USB_PHY
35 help
36 If you say yes here you get support for the Philips ISP1301
37 USB-On-The-Go transceiver working with the OMAP OTG controller.
38 The ISP1301 is a full speed USB transceiver which is used in
39 products including H2, H3, and H4 development boards for Texas
40 Instruments OMAP processors.
41
42 This driver can also be built as a module. If so, the module
43 will be called phy-isp1301-omap.
44
45config KEYSTONE_USB_PHY
46 tristate "Keystone USB PHY Driver"
47 depends on ARCH_KEYSTONE || COMPILE_TEST
48 depends on NOP_USB_XCEIV
49 help
50 Enable this to support Keystone USB phy. This driver provides
51 interface to interact with USB 2.0 and USB 3.0 PHY that is part
52 of the Keystone SOC.
53
54config NOP_USB_XCEIV
55 tristate "NOP USB Transceiver Driver"
56 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
57 select USB_PHY
58 help
59 This driver is to be used by all the usb transceiver which are either
60 built-in with usb ip or which are autonomous and doesn't require any
61 phy programming such as ISP1x04 etc.
62
63config AM335X_CONTROL_USB
64 tristate
65
66config AM335X_PHY_USB
67 tristate "AM335x USB PHY Driver"
68 depends on ARM || COMPILE_TEST
69 depends on NOP_USB_XCEIV
70 select USB_PHY
71 select AM335X_CONTROL_USB
72 select USB_COMMON
73 help
74 This driver provides PHY support for that phy which part for the
75 AM335x SoC.
76
77config SAMSUNG_USBPHY
78 tristate
79 help
80 Enable this to support Samsung USB phy helper driver for Samsung SoCs.
81 This driver provides common interface to interact, for Samsung USB 2.0 PHY
82 driver and later for Samsung USB 3.0 PHY driver.
83
84config TWL6030_USB
85 tristate "TWL6030 USB Transceiver Driver"
86 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
87 depends on OF
88 help
89 Enable this to support the USB OTG transceiver on TWL6030
90 family chips. This TWL6030 transceiver has the VBUS and ID GND
91 and OTG SRP events capabilities. For all other transceiver functionality
92 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
93 are hooked to this driver through platform_data structure.
94 The definition of internal PHY APIs are in the mach-omap2 layer.
95
96config USB_GPIO_VBUS
97 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
98 depends on GPIOLIB || COMPILE_TEST
99 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
100 select USB_PHY
101 help
102 Provides simple GPIO VBUS sensing for controllers with an
103 internal transceiver via the usb_phy interface, and
104 optionally control of a D+ pullup GPIO as well as a VBUS
105 current limit regulator.
106
107config OMAP_OTG
108 tristate "OMAP USB OTG controller driver"
109 depends on ARCH_OMAP_OTG && EXTCON
110 help
111 Enable this to support some transceivers on OMAP1 platforms. OTG
112 controller is needed to switch between host and peripheral modes.
113
114 This driver can also be built as a module. If so, the module
115 will be called phy-omap-otg.
116
117config TAHVO_USB
118 tristate "Tahvo USB transceiver driver"
119 depends on MFD_RETU && EXTCON
120 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
121 select USB_PHY
122 help
123 Enable this to support USB transceiver on Tahvo. This is used
124 at least on Nokia 770.
125
126config TAHVO_USB_HOST_BY_DEFAULT
127 depends on TAHVO_USB
128 bool "Device in USB host mode by default"
129 help
130 Say Y here, if you want the device to enter USB host mode
131 by default on bootup.
132
133config USB_ISP1301
134 tristate "NXP ISP1301 USB transceiver support"
135 depends on USB || USB_GADGET
136 depends on I2C
137 select USB_PHY
138 help
139 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
140 This chip is typically used as USB transceiver for USB host, gadget
141 and OTG drivers (to be selected separately).
142
143 To compile this driver as a module, choose M here: the
144 module will be called phy-isp1301.
145
146config USB_MSM_OTG
147 tristate "Qualcomm on-chip USB OTG controller support"
148 depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
149 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
150 depends on RESET_CONTROLLER
151 depends on EXTCON
152 select USB_PHY
153 help
154 Enable this to support the USB OTG transceiver on Qualcomm chips. It
155 handles PHY initialization, clock management, and workarounds
156 required after resetting the hardware and power management.
157 This driver is required even for peripheral only or host only
158 mode configurations.
159 This driver is not supported on boards like trout which
160 has an external PHY.
161
162config USB_QCOM_8X16_PHY
163 tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
164 depends on ARCH_QCOM || COMPILE_TEST
165 depends on RESET_CONTROLLER && EXTCON
166 select USB_PHY
167 select USB_ULPI_VIEWPORT
168 help
169 Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
170 It handles PHY initialization, clock management, power management,
171 and workarounds required after resetting the hardware.
172
173 To compile this driver as a module, choose M here: the
174 module will be called phy-qcom-8x16-usb.
175
176config USB_MV_OTG
177 tristate "Marvell USB OTG support"
178 depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
179 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
180 select USB_PHY
181 help
182 Say Y here if you want to build Marvell USB OTG transciever
183 driver in kernel (including PXA and MMP series). This driver
184 implements role switch between EHCI host driver and gadget driver.
185
186 To compile this driver as a module, choose M here.
187
188config USB_MXS_PHY
189 tristate "Freescale MXS USB PHY support"
190 depends on ARCH_MXC || ARCH_MXS
191 select STMP_DEVICE
192 select USB_PHY
193 help
194 Enable this to support the Freescale MXS USB PHY.
195
196 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
197
198config USB_ULPI
199 bool "Generic ULPI Transceiver Driver"
200 depends on ARM || ARM64
201 select USB_ULPI_VIEWPORT
202 help
203 Enable this to support ULPI connected USB OTG transceivers which
204 are likely found on embedded boards.
205
206config USB_ULPI_VIEWPORT
207 bool
208 help
209 Provides read/write operations to the ULPI phy register set for
210 controllers with a viewport register (e.g. Chipidea/ARC controllers).
211
212endmenu