Loading...
1// SPDX-License-Identifier: GPL-1.0+
2/*
3 * Device driver for Microgate SyncLink GT serial adapters.
4 *
5 * written by Paul Fulghum for Microgate Corporation
6 * paulkf@microgate.com
7 *
8 * Microgate and SyncLink are trademarks of Microgate Corporation
9 *
10 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
11 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
12 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
13 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
14 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
15 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
16 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
17 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
18 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
19 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
20 * OF THE POSSIBILITY OF SUCH DAMAGE.
21 */
22
23/*
24 * DEBUG OUTPUT DEFINITIONS
25 *
26 * uncomment lines below to enable specific types of debug output
27 *
28 * DBGINFO information - most verbose output
29 * DBGERR serious errors
30 * DBGBH bottom half service routine debugging
31 * DBGISR interrupt service routine debugging
32 * DBGDATA output receive and transmit data
33 * DBGTBUF output transmit DMA buffers and registers
34 * DBGRBUF output receive DMA buffers and registers
35 */
36
37#define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
38#define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
39#define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
40#define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
41#define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
42/*#define DBGTBUF(info) dump_tbufs(info)*/
43/*#define DBGRBUF(info) dump_rbufs(info)*/
44
45
46#include <linux/module.h>
47#include <linux/errno.h>
48#include <linux/signal.h>
49#include <linux/sched.h>
50#include <linux/timer.h>
51#include <linux/interrupt.h>
52#include <linux/pci.h>
53#include <linux/tty.h>
54#include <linux/tty_flip.h>
55#include <linux/serial.h>
56#include <linux/major.h>
57#include <linux/string.h>
58#include <linux/fcntl.h>
59#include <linux/ptrace.h>
60#include <linux/ioport.h>
61#include <linux/mm.h>
62#include <linux/seq_file.h>
63#include <linux/slab.h>
64#include <linux/netdevice.h>
65#include <linux/vmalloc.h>
66#include <linux/init.h>
67#include <linux/delay.h>
68#include <linux/ioctl.h>
69#include <linux/termios.h>
70#include <linux/bitops.h>
71#include <linux/workqueue.h>
72#include <linux/hdlc.h>
73#include <linux/synclink.h>
74
75#include <asm/io.h>
76#include <asm/irq.h>
77#include <asm/dma.h>
78#include <asm/types.h>
79#include <linux/uaccess.h>
80
81#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
82#define SYNCLINK_GENERIC_HDLC 1
83#else
84#define SYNCLINK_GENERIC_HDLC 0
85#endif
86
87/*
88 * module identification
89 */
90static char *driver_name = "SyncLink GT";
91static char *slgt_driver_name = "synclink_gt";
92static char *tty_dev_prefix = "ttySLG";
93MODULE_LICENSE("GPL");
94#define MGSL_MAGIC 0x5401
95#define MAX_DEVICES 32
96
97static const struct pci_device_id pci_table[] = {
98 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
99 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
100 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
101 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
102 {0,}, /* terminate list */
103};
104MODULE_DEVICE_TABLE(pci, pci_table);
105
106static int init_one(struct pci_dev *dev,const struct pci_device_id *ent);
107static void remove_one(struct pci_dev *dev);
108static struct pci_driver pci_driver = {
109 .name = "synclink_gt",
110 .id_table = pci_table,
111 .probe = init_one,
112 .remove = remove_one,
113};
114
115static bool pci_registered;
116
117/*
118 * module configuration and status
119 */
120static struct slgt_info *slgt_device_list;
121static int slgt_device_count;
122
123static int ttymajor;
124static int debug_level;
125static int maxframe[MAX_DEVICES];
126
127module_param(ttymajor, int, 0);
128module_param(debug_level, int, 0);
129module_param_array(maxframe, int, NULL, 0);
130
131MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
132MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
133MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
134
135/*
136 * tty support and callbacks
137 */
138static struct tty_driver *serial_driver;
139
140static int open(struct tty_struct *tty, struct file * filp);
141static void close(struct tty_struct *tty, struct file * filp);
142static void hangup(struct tty_struct *tty);
143static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
144
145static int write(struct tty_struct *tty, const unsigned char *buf, int count);
146static int put_char(struct tty_struct *tty, unsigned char ch);
147static void send_xchar(struct tty_struct *tty, char ch);
148static void wait_until_sent(struct tty_struct *tty, int timeout);
149static int write_room(struct tty_struct *tty);
150static void flush_chars(struct tty_struct *tty);
151static void flush_buffer(struct tty_struct *tty);
152static void tx_hold(struct tty_struct *tty);
153static void tx_release(struct tty_struct *tty);
154
155static int ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
156static int chars_in_buffer(struct tty_struct *tty);
157static void throttle(struct tty_struct * tty);
158static void unthrottle(struct tty_struct * tty);
159static int set_break(struct tty_struct *tty, int break_state);
160
161/*
162 * generic HDLC support and callbacks
163 */
164#if SYNCLINK_GENERIC_HDLC
165#define dev_to_port(D) (dev_to_hdlc(D)->priv)
166static void hdlcdev_tx_done(struct slgt_info *info);
167static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
168static int hdlcdev_init(struct slgt_info *info);
169static void hdlcdev_exit(struct slgt_info *info);
170#endif
171
172
173/*
174 * device specific structures, macros and functions
175 */
176
177#define SLGT_MAX_PORTS 4
178#define SLGT_REG_SIZE 256
179
180/*
181 * conditional wait facility
182 */
183struct cond_wait {
184 struct cond_wait *next;
185 wait_queue_head_t q;
186 wait_queue_entry_t wait;
187 unsigned int data;
188};
189static void init_cond_wait(struct cond_wait *w, unsigned int data);
190static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
191static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
192static void flush_cond_wait(struct cond_wait **head);
193
194/*
195 * DMA buffer descriptor and access macros
196 */
197struct slgt_desc
198{
199 __le16 count;
200 __le16 status;
201 __le32 pbuf; /* physical address of data buffer */
202 __le32 next; /* physical address of next descriptor */
203
204 /* driver book keeping */
205 char *buf; /* virtual address of data buffer */
206 unsigned int pdesc; /* physical address of this descriptor */
207 dma_addr_t buf_dma_addr;
208 unsigned short buf_count;
209};
210
211#define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
212#define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b))
213#define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b))
214#define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
215#define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
216#define desc_count(a) (le16_to_cpu((a).count))
217#define desc_status(a) (le16_to_cpu((a).status))
218#define desc_complete(a) (le16_to_cpu((a).status) & BIT15)
219#define desc_eof(a) (le16_to_cpu((a).status) & BIT2)
220#define desc_crc_error(a) (le16_to_cpu((a).status) & BIT1)
221#define desc_abort(a) (le16_to_cpu((a).status) & BIT0)
222#define desc_residue(a) ((le16_to_cpu((a).status) & 0x38) >> 3)
223
224struct _input_signal_events {
225 int ri_up;
226 int ri_down;
227 int dsr_up;
228 int dsr_down;
229 int dcd_up;
230 int dcd_down;
231 int cts_up;
232 int cts_down;
233};
234
235/*
236 * device instance data structure
237 */
238struct slgt_info {
239 void *if_ptr; /* General purpose pointer (used by SPPP) */
240 struct tty_port port;
241
242 struct slgt_info *next_device; /* device list link */
243
244 int magic;
245
246 char device_name[25];
247 struct pci_dev *pdev;
248
249 int port_count; /* count of ports on adapter */
250 int adapter_num; /* adapter instance number */
251 int port_num; /* port instance number */
252
253 /* array of pointers to port contexts on this adapter */
254 struct slgt_info *port_array[SLGT_MAX_PORTS];
255
256 int line; /* tty line instance number */
257
258 struct mgsl_icount icount;
259
260 int timeout;
261 int x_char; /* xon/xoff character */
262 unsigned int read_status_mask;
263 unsigned int ignore_status_mask;
264
265 wait_queue_head_t status_event_wait_q;
266 wait_queue_head_t event_wait_q;
267 struct timer_list tx_timer;
268 struct timer_list rx_timer;
269
270 unsigned int gpio_present;
271 struct cond_wait *gpio_wait_q;
272
273 spinlock_t lock; /* spinlock for synchronizing with ISR */
274
275 struct work_struct task;
276 u32 pending_bh;
277 bool bh_requested;
278 bool bh_running;
279
280 int isr_overflow;
281 bool irq_requested; /* true if IRQ requested */
282 bool irq_occurred; /* for diagnostics use */
283
284 /* device configuration */
285
286 unsigned int bus_type;
287 unsigned int irq_level;
288 unsigned long irq_flags;
289
290 unsigned char __iomem * reg_addr; /* memory mapped registers address */
291 u32 phys_reg_addr;
292 bool reg_addr_requested;
293
294 MGSL_PARAMS params; /* communications parameters */
295 u32 idle_mode;
296 u32 max_frame_size; /* as set by device config */
297
298 unsigned int rbuf_fill_level;
299 unsigned int rx_pio;
300 unsigned int if_mode;
301 unsigned int base_clock;
302 unsigned int xsync;
303 unsigned int xctrl;
304
305 /* device status */
306
307 bool rx_enabled;
308 bool rx_restart;
309
310 bool tx_enabled;
311 bool tx_active;
312
313 unsigned char signals; /* serial signal states */
314 int init_error; /* initialization error */
315
316 unsigned char *tx_buf;
317 int tx_count;
318
319 char *flag_buf;
320 bool drop_rts_on_tx_done;
321 struct _input_signal_events input_signal_events;
322
323 int dcd_chkcount; /* check counts to prevent */
324 int cts_chkcount; /* too many IRQs if a signal */
325 int dsr_chkcount; /* is floating */
326 int ri_chkcount;
327
328 char *bufs; /* virtual address of DMA buffer lists */
329 dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
330
331 unsigned int rbuf_count;
332 struct slgt_desc *rbufs;
333 unsigned int rbuf_current;
334 unsigned int rbuf_index;
335 unsigned int rbuf_fill_index;
336 unsigned short rbuf_fill_count;
337
338 unsigned int tbuf_count;
339 struct slgt_desc *tbufs;
340 unsigned int tbuf_current;
341 unsigned int tbuf_start;
342
343 unsigned char *tmp_rbuf;
344 unsigned int tmp_rbuf_count;
345
346 /* SPPP/Cisco HDLC device parts */
347
348 int netcount;
349 spinlock_t netlock;
350#if SYNCLINK_GENERIC_HDLC
351 struct net_device *netdev;
352#endif
353
354};
355
356static MGSL_PARAMS default_params = {
357 .mode = MGSL_MODE_HDLC,
358 .loopback = 0,
359 .flags = HDLC_FLAG_UNDERRUN_ABORT15,
360 .encoding = HDLC_ENCODING_NRZI_SPACE,
361 .clock_speed = 0,
362 .addr_filter = 0xff,
363 .crc_type = HDLC_CRC_16_CCITT,
364 .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
365 .preamble = HDLC_PREAMBLE_PATTERN_NONE,
366 .data_rate = 9600,
367 .data_bits = 8,
368 .stop_bits = 1,
369 .parity = ASYNC_PARITY_NONE
370};
371
372
373#define BH_RECEIVE 1
374#define BH_TRANSMIT 2
375#define BH_STATUS 4
376#define IO_PIN_SHUTDOWN_LIMIT 100
377
378#define DMABUFSIZE 256
379#define DESC_LIST_SIZE 4096
380
381#define MASK_PARITY BIT1
382#define MASK_FRAMING BIT0
383#define MASK_BREAK BIT14
384#define MASK_OVERRUN BIT4
385
386#define GSR 0x00 /* global status */
387#define JCR 0x04 /* JTAG control */
388#define IODR 0x08 /* GPIO direction */
389#define IOER 0x0c /* GPIO interrupt enable */
390#define IOVR 0x10 /* GPIO value */
391#define IOSR 0x14 /* GPIO interrupt status */
392#define TDR 0x80 /* tx data */
393#define RDR 0x80 /* rx data */
394#define TCR 0x82 /* tx control */
395#define TIR 0x84 /* tx idle */
396#define TPR 0x85 /* tx preamble */
397#define RCR 0x86 /* rx control */
398#define VCR 0x88 /* V.24 control */
399#define CCR 0x89 /* clock control */
400#define BDR 0x8a /* baud divisor */
401#define SCR 0x8c /* serial control */
402#define SSR 0x8e /* serial status */
403#define RDCSR 0x90 /* rx DMA control/status */
404#define TDCSR 0x94 /* tx DMA control/status */
405#define RDDAR 0x98 /* rx DMA descriptor address */
406#define TDDAR 0x9c /* tx DMA descriptor address */
407#define XSR 0x40 /* extended sync pattern */
408#define XCR 0x44 /* extended control */
409
410#define RXIDLE BIT14
411#define RXBREAK BIT14
412#define IRQ_TXDATA BIT13
413#define IRQ_TXIDLE BIT12
414#define IRQ_TXUNDER BIT11 /* HDLC */
415#define IRQ_RXDATA BIT10
416#define IRQ_RXIDLE BIT9 /* HDLC */
417#define IRQ_RXBREAK BIT9 /* async */
418#define IRQ_RXOVER BIT8
419#define IRQ_DSR BIT7
420#define IRQ_CTS BIT6
421#define IRQ_DCD BIT5
422#define IRQ_RI BIT4
423#define IRQ_ALL 0x3ff0
424#define IRQ_MASTER BIT0
425
426#define slgt_irq_on(info, mask) \
427 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
428#define slgt_irq_off(info, mask) \
429 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
430
431static __u8 rd_reg8(struct slgt_info *info, unsigned int addr);
432static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
433static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
434static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
435static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
436static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
437
438static void msc_set_vcr(struct slgt_info *info);
439
440static int startup(struct slgt_info *info);
441static int block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
442static void shutdown(struct slgt_info *info);
443static void program_hw(struct slgt_info *info);
444static void change_params(struct slgt_info *info);
445
446static int register_test(struct slgt_info *info);
447static int irq_test(struct slgt_info *info);
448static int loopback_test(struct slgt_info *info);
449static int adapter_test(struct slgt_info *info);
450
451static void reset_adapter(struct slgt_info *info);
452static void reset_port(struct slgt_info *info);
453static void async_mode(struct slgt_info *info);
454static void sync_mode(struct slgt_info *info);
455
456static void rx_stop(struct slgt_info *info);
457static void rx_start(struct slgt_info *info);
458static void reset_rbufs(struct slgt_info *info);
459static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
460static void rdma_reset(struct slgt_info *info);
461static bool rx_get_frame(struct slgt_info *info);
462static bool rx_get_buf(struct slgt_info *info);
463
464static void tx_start(struct slgt_info *info);
465static void tx_stop(struct slgt_info *info);
466static void tx_set_idle(struct slgt_info *info);
467static unsigned int free_tbuf_count(struct slgt_info *info);
468static unsigned int tbuf_bytes(struct slgt_info *info);
469static void reset_tbufs(struct slgt_info *info);
470static void tdma_reset(struct slgt_info *info);
471static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
472
473static void get_signals(struct slgt_info *info);
474static void set_signals(struct slgt_info *info);
475static void enable_loopback(struct slgt_info *info);
476static void set_rate(struct slgt_info *info, u32 data_rate);
477
478static int bh_action(struct slgt_info *info);
479static void bh_handler(struct work_struct *work);
480static void bh_transmit(struct slgt_info *info);
481static void isr_serial(struct slgt_info *info);
482static void isr_rdma(struct slgt_info *info);
483static void isr_txeom(struct slgt_info *info, unsigned short status);
484static void isr_tdma(struct slgt_info *info);
485
486static int alloc_dma_bufs(struct slgt_info *info);
487static void free_dma_bufs(struct slgt_info *info);
488static int alloc_desc(struct slgt_info *info);
489static void free_desc(struct slgt_info *info);
490static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
491static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
492
493static int alloc_tmp_rbuf(struct slgt_info *info);
494static void free_tmp_rbuf(struct slgt_info *info);
495
496static void tx_timeout(struct timer_list *t);
497static void rx_timeout(struct timer_list *t);
498
499/*
500 * ioctl handlers
501 */
502static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
503static int get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
504static int set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
505static int get_txidle(struct slgt_info *info, int __user *idle_mode);
506static int set_txidle(struct slgt_info *info, int idle_mode);
507static int tx_enable(struct slgt_info *info, int enable);
508static int tx_abort(struct slgt_info *info);
509static int rx_enable(struct slgt_info *info, int enable);
510static int modem_input_wait(struct slgt_info *info,int arg);
511static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
512static int tiocmget(struct tty_struct *tty);
513static int tiocmset(struct tty_struct *tty,
514 unsigned int set, unsigned int clear);
515static int set_break(struct tty_struct *tty, int break_state);
516static int get_interface(struct slgt_info *info, int __user *if_mode);
517static int set_interface(struct slgt_info *info, int if_mode);
518static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
519static int get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
520static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
521static int get_xsync(struct slgt_info *info, int __user *if_mode);
522static int set_xsync(struct slgt_info *info, int if_mode);
523static int get_xctrl(struct slgt_info *info, int __user *if_mode);
524static int set_xctrl(struct slgt_info *info, int if_mode);
525
526/*
527 * driver functions
528 */
529static void add_device(struct slgt_info *info);
530static void device_init(int adapter_num, struct pci_dev *pdev);
531static int claim_resources(struct slgt_info *info);
532static void release_resources(struct slgt_info *info);
533
534/*
535 * DEBUG OUTPUT CODE
536 */
537#ifndef DBGINFO
538#define DBGINFO(fmt)
539#endif
540#ifndef DBGERR
541#define DBGERR(fmt)
542#endif
543#ifndef DBGBH
544#define DBGBH(fmt)
545#endif
546#ifndef DBGISR
547#define DBGISR(fmt)
548#endif
549
550#ifdef DBGDATA
551static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
552{
553 int i;
554 int linecount;
555 printk("%s %s data:\n",info->device_name, label);
556 while(count) {
557 linecount = (count > 16) ? 16 : count;
558 for(i=0; i < linecount; i++)
559 printk("%02X ",(unsigned char)data[i]);
560 for(;i<17;i++)
561 printk(" ");
562 for(i=0;i<linecount;i++) {
563 if (data[i]>=040 && data[i]<=0176)
564 printk("%c",data[i]);
565 else
566 printk(".");
567 }
568 printk("\n");
569 data += linecount;
570 count -= linecount;
571 }
572}
573#else
574#define DBGDATA(info, buf, size, label)
575#endif
576
577#ifdef DBGTBUF
578static void dump_tbufs(struct slgt_info *info)
579{
580 int i;
581 printk("tbuf_current=%d\n", info->tbuf_current);
582 for (i=0 ; i < info->tbuf_count ; i++) {
583 printk("%d: count=%04X status=%04X\n",
584 i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
585 }
586}
587#else
588#define DBGTBUF(info)
589#endif
590
591#ifdef DBGRBUF
592static void dump_rbufs(struct slgt_info *info)
593{
594 int i;
595 printk("rbuf_current=%d\n", info->rbuf_current);
596 for (i=0 ; i < info->rbuf_count ; i++) {
597 printk("%d: count=%04X status=%04X\n",
598 i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
599 }
600}
601#else
602#define DBGRBUF(info)
603#endif
604
605static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
606{
607#ifdef SANITY_CHECK
608 if (!info) {
609 printk("null struct slgt_info for (%s) in %s\n", devname, name);
610 return 1;
611 }
612 if (info->magic != MGSL_MAGIC) {
613 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
614 return 1;
615 }
616#else
617 if (!info)
618 return 1;
619#endif
620 return 0;
621}
622
623/**
624 * line discipline callback wrappers
625 *
626 * The wrappers maintain line discipline references
627 * while calling into the line discipline.
628 *
629 * ldisc_receive_buf - pass receive data to line discipline
630 */
631static void ldisc_receive_buf(struct tty_struct *tty,
632 const __u8 *data, char *flags, int count)
633{
634 struct tty_ldisc *ld;
635 if (!tty)
636 return;
637 ld = tty_ldisc_ref(tty);
638 if (ld) {
639 if (ld->ops->receive_buf)
640 ld->ops->receive_buf(tty, data, flags, count);
641 tty_ldisc_deref(ld);
642 }
643}
644
645/* tty callbacks */
646
647static int open(struct tty_struct *tty, struct file *filp)
648{
649 struct slgt_info *info;
650 int retval, line;
651 unsigned long flags;
652
653 line = tty->index;
654 if (line >= slgt_device_count) {
655 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
656 return -ENODEV;
657 }
658
659 info = slgt_device_list;
660 while(info && info->line != line)
661 info = info->next_device;
662 if (sanity_check(info, tty->name, "open"))
663 return -ENODEV;
664 if (info->init_error) {
665 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
666 return -ENODEV;
667 }
668
669 tty->driver_data = info;
670 info->port.tty = tty;
671
672 DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
673
674 mutex_lock(&info->port.mutex);
675 info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
676
677 spin_lock_irqsave(&info->netlock, flags);
678 if (info->netcount) {
679 retval = -EBUSY;
680 spin_unlock_irqrestore(&info->netlock, flags);
681 mutex_unlock(&info->port.mutex);
682 goto cleanup;
683 }
684 info->port.count++;
685 spin_unlock_irqrestore(&info->netlock, flags);
686
687 if (info->port.count == 1) {
688 /* 1st open on this device, init hardware */
689 retval = startup(info);
690 if (retval < 0) {
691 mutex_unlock(&info->port.mutex);
692 goto cleanup;
693 }
694 }
695 mutex_unlock(&info->port.mutex);
696 retval = block_til_ready(tty, filp, info);
697 if (retval) {
698 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
699 goto cleanup;
700 }
701
702 retval = 0;
703
704cleanup:
705 if (retval) {
706 if (tty->count == 1)
707 info->port.tty = NULL; /* tty layer will release tty struct */
708 if(info->port.count)
709 info->port.count--;
710 }
711
712 DBGINFO(("%s open rc=%d\n", info->device_name, retval));
713 return retval;
714}
715
716static void close(struct tty_struct *tty, struct file *filp)
717{
718 struct slgt_info *info = tty->driver_data;
719
720 if (sanity_check(info, tty->name, "close"))
721 return;
722 DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
723
724 if (tty_port_close_start(&info->port, tty, filp) == 0)
725 goto cleanup;
726
727 mutex_lock(&info->port.mutex);
728 if (tty_port_initialized(&info->port))
729 wait_until_sent(tty, info->timeout);
730 flush_buffer(tty);
731 tty_ldisc_flush(tty);
732
733 shutdown(info);
734 mutex_unlock(&info->port.mutex);
735
736 tty_port_close_end(&info->port, tty);
737 info->port.tty = NULL;
738cleanup:
739 DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
740}
741
742static void hangup(struct tty_struct *tty)
743{
744 struct slgt_info *info = tty->driver_data;
745 unsigned long flags;
746
747 if (sanity_check(info, tty->name, "hangup"))
748 return;
749 DBGINFO(("%s hangup\n", info->device_name));
750
751 flush_buffer(tty);
752
753 mutex_lock(&info->port.mutex);
754 shutdown(info);
755
756 spin_lock_irqsave(&info->port.lock, flags);
757 info->port.count = 0;
758 info->port.tty = NULL;
759 spin_unlock_irqrestore(&info->port.lock, flags);
760 tty_port_set_active(&info->port, 0);
761 mutex_unlock(&info->port.mutex);
762
763 wake_up_interruptible(&info->port.open_wait);
764}
765
766static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
767{
768 struct slgt_info *info = tty->driver_data;
769 unsigned long flags;
770
771 DBGINFO(("%s set_termios\n", tty->driver->name));
772
773 change_params(info);
774
775 /* Handle transition to B0 status */
776 if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) {
777 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
778 spin_lock_irqsave(&info->lock,flags);
779 set_signals(info);
780 spin_unlock_irqrestore(&info->lock,flags);
781 }
782
783 /* Handle transition away from B0 status */
784 if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
785 info->signals |= SerialSignal_DTR;
786 if (!C_CRTSCTS(tty) || !tty_throttled(tty))
787 info->signals |= SerialSignal_RTS;
788 spin_lock_irqsave(&info->lock,flags);
789 set_signals(info);
790 spin_unlock_irqrestore(&info->lock,flags);
791 }
792
793 /* Handle turning off CRTSCTS */
794 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
795 tty->hw_stopped = 0;
796 tx_release(tty);
797 }
798}
799
800static void update_tx_timer(struct slgt_info *info)
801{
802 /*
803 * use worst case speed of 1200bps to calculate transmit timeout
804 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
805 */
806 if (info->params.mode == MGSL_MODE_HDLC) {
807 int timeout = (tbuf_bytes(info) * 7) + 1000;
808 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
809 }
810}
811
812static int write(struct tty_struct *tty,
813 const unsigned char *buf, int count)
814{
815 int ret = 0;
816 struct slgt_info *info = tty->driver_data;
817 unsigned long flags;
818
819 if (sanity_check(info, tty->name, "write"))
820 return -EIO;
821
822 DBGINFO(("%s write count=%d\n", info->device_name, count));
823
824 if (!info->tx_buf || (count > info->max_frame_size))
825 return -EIO;
826
827 if (!count || tty->stopped || tty->hw_stopped)
828 return 0;
829
830 spin_lock_irqsave(&info->lock, flags);
831
832 if (info->tx_count) {
833 /* send accumulated data from send_char() */
834 if (!tx_load(info, info->tx_buf, info->tx_count))
835 goto cleanup;
836 info->tx_count = 0;
837 }
838
839 if (tx_load(info, buf, count))
840 ret = count;
841
842cleanup:
843 spin_unlock_irqrestore(&info->lock, flags);
844 DBGINFO(("%s write rc=%d\n", info->device_name, ret));
845 return ret;
846}
847
848static int put_char(struct tty_struct *tty, unsigned char ch)
849{
850 struct slgt_info *info = tty->driver_data;
851 unsigned long flags;
852 int ret = 0;
853
854 if (sanity_check(info, tty->name, "put_char"))
855 return 0;
856 DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
857 if (!info->tx_buf)
858 return 0;
859 spin_lock_irqsave(&info->lock,flags);
860 if (info->tx_count < info->max_frame_size) {
861 info->tx_buf[info->tx_count++] = ch;
862 ret = 1;
863 }
864 spin_unlock_irqrestore(&info->lock,flags);
865 return ret;
866}
867
868static void send_xchar(struct tty_struct *tty, char ch)
869{
870 struct slgt_info *info = tty->driver_data;
871 unsigned long flags;
872
873 if (sanity_check(info, tty->name, "send_xchar"))
874 return;
875 DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
876 info->x_char = ch;
877 if (ch) {
878 spin_lock_irqsave(&info->lock,flags);
879 if (!info->tx_enabled)
880 tx_start(info);
881 spin_unlock_irqrestore(&info->lock,flags);
882 }
883}
884
885static void wait_until_sent(struct tty_struct *tty, int timeout)
886{
887 struct slgt_info *info = tty->driver_data;
888 unsigned long orig_jiffies, char_time;
889
890 if (!info )
891 return;
892 if (sanity_check(info, tty->name, "wait_until_sent"))
893 return;
894 DBGINFO(("%s wait_until_sent entry\n", info->device_name));
895 if (!tty_port_initialized(&info->port))
896 goto exit;
897
898 orig_jiffies = jiffies;
899
900 /* Set check interval to 1/5 of estimated time to
901 * send a character, and make it at least 1. The check
902 * interval should also be less than the timeout.
903 * Note: use tight timings here to satisfy the NIST-PCTS.
904 */
905
906 if (info->params.data_rate) {
907 char_time = info->timeout/(32 * 5);
908 if (!char_time)
909 char_time++;
910 } else
911 char_time = 1;
912
913 if (timeout)
914 char_time = min_t(unsigned long, char_time, timeout);
915
916 while (info->tx_active) {
917 msleep_interruptible(jiffies_to_msecs(char_time));
918 if (signal_pending(current))
919 break;
920 if (timeout && time_after(jiffies, orig_jiffies + timeout))
921 break;
922 }
923exit:
924 DBGINFO(("%s wait_until_sent exit\n", info->device_name));
925}
926
927static int write_room(struct tty_struct *tty)
928{
929 struct slgt_info *info = tty->driver_data;
930 int ret;
931
932 if (sanity_check(info, tty->name, "write_room"))
933 return 0;
934 ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
935 DBGINFO(("%s write_room=%d\n", info->device_name, ret));
936 return ret;
937}
938
939static void flush_chars(struct tty_struct *tty)
940{
941 struct slgt_info *info = tty->driver_data;
942 unsigned long flags;
943
944 if (sanity_check(info, tty->name, "flush_chars"))
945 return;
946 DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
947
948 if (info->tx_count <= 0 || tty->stopped ||
949 tty->hw_stopped || !info->tx_buf)
950 return;
951
952 DBGINFO(("%s flush_chars start transmit\n", info->device_name));
953
954 spin_lock_irqsave(&info->lock,flags);
955 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
956 info->tx_count = 0;
957 spin_unlock_irqrestore(&info->lock,flags);
958}
959
960static void flush_buffer(struct tty_struct *tty)
961{
962 struct slgt_info *info = tty->driver_data;
963 unsigned long flags;
964
965 if (sanity_check(info, tty->name, "flush_buffer"))
966 return;
967 DBGINFO(("%s flush_buffer\n", info->device_name));
968
969 spin_lock_irqsave(&info->lock, flags);
970 info->tx_count = 0;
971 spin_unlock_irqrestore(&info->lock, flags);
972
973 tty_wakeup(tty);
974}
975
976/*
977 * throttle (stop) transmitter
978 */
979static void tx_hold(struct tty_struct *tty)
980{
981 struct slgt_info *info = tty->driver_data;
982 unsigned long flags;
983
984 if (sanity_check(info, tty->name, "tx_hold"))
985 return;
986 DBGINFO(("%s tx_hold\n", info->device_name));
987 spin_lock_irqsave(&info->lock,flags);
988 if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
989 tx_stop(info);
990 spin_unlock_irqrestore(&info->lock,flags);
991}
992
993/*
994 * release (start) transmitter
995 */
996static void tx_release(struct tty_struct *tty)
997{
998 struct slgt_info *info = tty->driver_data;
999 unsigned long flags;
1000
1001 if (sanity_check(info, tty->name, "tx_release"))
1002 return;
1003 DBGINFO(("%s tx_release\n", info->device_name));
1004 spin_lock_irqsave(&info->lock, flags);
1005 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
1006 info->tx_count = 0;
1007 spin_unlock_irqrestore(&info->lock, flags);
1008}
1009
1010/*
1011 * Service an IOCTL request
1012 *
1013 * Arguments
1014 *
1015 * tty pointer to tty instance data
1016 * cmd IOCTL command code
1017 * arg command argument/context
1018 *
1019 * Return 0 if success, otherwise error code
1020 */
1021static int ioctl(struct tty_struct *tty,
1022 unsigned int cmd, unsigned long arg)
1023{
1024 struct slgt_info *info = tty->driver_data;
1025 void __user *argp = (void __user *)arg;
1026 int ret;
1027
1028 if (sanity_check(info, tty->name, "ioctl"))
1029 return -ENODEV;
1030 DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1031
1032 if (cmd != TIOCMIWAIT) {
1033 if (tty_io_error(tty))
1034 return -EIO;
1035 }
1036
1037 switch (cmd) {
1038 case MGSL_IOCWAITEVENT:
1039 return wait_mgsl_event(info, argp);
1040 case TIOCMIWAIT:
1041 return modem_input_wait(info,(int)arg);
1042 case MGSL_IOCSGPIO:
1043 return set_gpio(info, argp);
1044 case MGSL_IOCGGPIO:
1045 return get_gpio(info, argp);
1046 case MGSL_IOCWAITGPIO:
1047 return wait_gpio(info, argp);
1048 case MGSL_IOCGXSYNC:
1049 return get_xsync(info, argp);
1050 case MGSL_IOCSXSYNC:
1051 return set_xsync(info, (int)arg);
1052 case MGSL_IOCGXCTRL:
1053 return get_xctrl(info, argp);
1054 case MGSL_IOCSXCTRL:
1055 return set_xctrl(info, (int)arg);
1056 }
1057 mutex_lock(&info->port.mutex);
1058 switch (cmd) {
1059 case MGSL_IOCGPARAMS:
1060 ret = get_params(info, argp);
1061 break;
1062 case MGSL_IOCSPARAMS:
1063 ret = set_params(info, argp);
1064 break;
1065 case MGSL_IOCGTXIDLE:
1066 ret = get_txidle(info, argp);
1067 break;
1068 case MGSL_IOCSTXIDLE:
1069 ret = set_txidle(info, (int)arg);
1070 break;
1071 case MGSL_IOCTXENABLE:
1072 ret = tx_enable(info, (int)arg);
1073 break;
1074 case MGSL_IOCRXENABLE:
1075 ret = rx_enable(info, (int)arg);
1076 break;
1077 case MGSL_IOCTXABORT:
1078 ret = tx_abort(info);
1079 break;
1080 case MGSL_IOCGSTATS:
1081 ret = get_stats(info, argp);
1082 break;
1083 case MGSL_IOCGIF:
1084 ret = get_interface(info, argp);
1085 break;
1086 case MGSL_IOCSIF:
1087 ret = set_interface(info,(int)arg);
1088 break;
1089 default:
1090 ret = -ENOIOCTLCMD;
1091 }
1092 mutex_unlock(&info->port.mutex);
1093 return ret;
1094}
1095
1096static int get_icount(struct tty_struct *tty,
1097 struct serial_icounter_struct *icount)
1098
1099{
1100 struct slgt_info *info = tty->driver_data;
1101 struct mgsl_icount cnow; /* kernel counter temps */
1102 unsigned long flags;
1103
1104 spin_lock_irqsave(&info->lock,flags);
1105 cnow = info->icount;
1106 spin_unlock_irqrestore(&info->lock,flags);
1107
1108 icount->cts = cnow.cts;
1109 icount->dsr = cnow.dsr;
1110 icount->rng = cnow.rng;
1111 icount->dcd = cnow.dcd;
1112 icount->rx = cnow.rx;
1113 icount->tx = cnow.tx;
1114 icount->frame = cnow.frame;
1115 icount->overrun = cnow.overrun;
1116 icount->parity = cnow.parity;
1117 icount->brk = cnow.brk;
1118 icount->buf_overrun = cnow.buf_overrun;
1119
1120 return 0;
1121}
1122
1123/*
1124 * support for 32 bit ioctl calls on 64 bit systems
1125 */
1126#ifdef CONFIG_COMPAT
1127static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1128{
1129 struct MGSL_PARAMS32 tmp_params;
1130
1131 DBGINFO(("%s get_params32\n", info->device_name));
1132 memset(&tmp_params, 0, sizeof(tmp_params));
1133 tmp_params.mode = (compat_ulong_t)info->params.mode;
1134 tmp_params.loopback = info->params.loopback;
1135 tmp_params.flags = info->params.flags;
1136 tmp_params.encoding = info->params.encoding;
1137 tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed;
1138 tmp_params.addr_filter = info->params.addr_filter;
1139 tmp_params.crc_type = info->params.crc_type;
1140 tmp_params.preamble_length = info->params.preamble_length;
1141 tmp_params.preamble = info->params.preamble;
1142 tmp_params.data_rate = (compat_ulong_t)info->params.data_rate;
1143 tmp_params.data_bits = info->params.data_bits;
1144 tmp_params.stop_bits = info->params.stop_bits;
1145 tmp_params.parity = info->params.parity;
1146 if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1147 return -EFAULT;
1148 return 0;
1149}
1150
1151static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1152{
1153 struct MGSL_PARAMS32 tmp_params;
1154
1155 DBGINFO(("%s set_params32\n", info->device_name));
1156 if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1157 return -EFAULT;
1158
1159 spin_lock(&info->lock);
1160 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1161 info->base_clock = tmp_params.clock_speed;
1162 } else {
1163 info->params.mode = tmp_params.mode;
1164 info->params.loopback = tmp_params.loopback;
1165 info->params.flags = tmp_params.flags;
1166 info->params.encoding = tmp_params.encoding;
1167 info->params.clock_speed = tmp_params.clock_speed;
1168 info->params.addr_filter = tmp_params.addr_filter;
1169 info->params.crc_type = tmp_params.crc_type;
1170 info->params.preamble_length = tmp_params.preamble_length;
1171 info->params.preamble = tmp_params.preamble;
1172 info->params.data_rate = tmp_params.data_rate;
1173 info->params.data_bits = tmp_params.data_bits;
1174 info->params.stop_bits = tmp_params.stop_bits;
1175 info->params.parity = tmp_params.parity;
1176 }
1177 spin_unlock(&info->lock);
1178
1179 program_hw(info);
1180
1181 return 0;
1182}
1183
1184static long slgt_compat_ioctl(struct tty_struct *tty,
1185 unsigned int cmd, unsigned long arg)
1186{
1187 struct slgt_info *info = tty->driver_data;
1188 int rc;
1189
1190 if (sanity_check(info, tty->name, "compat_ioctl"))
1191 return -ENODEV;
1192 DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1193
1194 switch (cmd) {
1195 case MGSL_IOCSPARAMS32:
1196 rc = set_params32(info, compat_ptr(arg));
1197 break;
1198
1199 case MGSL_IOCGPARAMS32:
1200 rc = get_params32(info, compat_ptr(arg));
1201 break;
1202
1203 case MGSL_IOCGPARAMS:
1204 case MGSL_IOCSPARAMS:
1205 case MGSL_IOCGTXIDLE:
1206 case MGSL_IOCGSTATS:
1207 case MGSL_IOCWAITEVENT:
1208 case MGSL_IOCGIF:
1209 case MGSL_IOCSGPIO:
1210 case MGSL_IOCGGPIO:
1211 case MGSL_IOCWAITGPIO:
1212 case MGSL_IOCGXSYNC:
1213 case MGSL_IOCGXCTRL:
1214 rc = ioctl(tty, cmd, (unsigned long)compat_ptr(arg));
1215 break;
1216 default:
1217 rc = ioctl(tty, cmd, arg);
1218 }
1219 DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1220 return rc;
1221}
1222#else
1223#define slgt_compat_ioctl NULL
1224#endif /* ifdef CONFIG_COMPAT */
1225
1226/*
1227 * proc fs support
1228 */
1229static inline void line_info(struct seq_file *m, struct slgt_info *info)
1230{
1231 char stat_buf[30];
1232 unsigned long flags;
1233
1234 seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1235 info->device_name, info->phys_reg_addr,
1236 info->irq_level, info->max_frame_size);
1237
1238 /* output current serial signal states */
1239 spin_lock_irqsave(&info->lock,flags);
1240 get_signals(info);
1241 spin_unlock_irqrestore(&info->lock,flags);
1242
1243 stat_buf[0] = 0;
1244 stat_buf[1] = 0;
1245 if (info->signals & SerialSignal_RTS)
1246 strcat(stat_buf, "|RTS");
1247 if (info->signals & SerialSignal_CTS)
1248 strcat(stat_buf, "|CTS");
1249 if (info->signals & SerialSignal_DTR)
1250 strcat(stat_buf, "|DTR");
1251 if (info->signals & SerialSignal_DSR)
1252 strcat(stat_buf, "|DSR");
1253 if (info->signals & SerialSignal_DCD)
1254 strcat(stat_buf, "|CD");
1255 if (info->signals & SerialSignal_RI)
1256 strcat(stat_buf, "|RI");
1257
1258 if (info->params.mode != MGSL_MODE_ASYNC) {
1259 seq_printf(m, "\tHDLC txok:%d rxok:%d",
1260 info->icount.txok, info->icount.rxok);
1261 if (info->icount.txunder)
1262 seq_printf(m, " txunder:%d", info->icount.txunder);
1263 if (info->icount.txabort)
1264 seq_printf(m, " txabort:%d", info->icount.txabort);
1265 if (info->icount.rxshort)
1266 seq_printf(m, " rxshort:%d", info->icount.rxshort);
1267 if (info->icount.rxlong)
1268 seq_printf(m, " rxlong:%d", info->icount.rxlong);
1269 if (info->icount.rxover)
1270 seq_printf(m, " rxover:%d", info->icount.rxover);
1271 if (info->icount.rxcrc)
1272 seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1273 } else {
1274 seq_printf(m, "\tASYNC tx:%d rx:%d",
1275 info->icount.tx, info->icount.rx);
1276 if (info->icount.frame)
1277 seq_printf(m, " fe:%d", info->icount.frame);
1278 if (info->icount.parity)
1279 seq_printf(m, " pe:%d", info->icount.parity);
1280 if (info->icount.brk)
1281 seq_printf(m, " brk:%d", info->icount.brk);
1282 if (info->icount.overrun)
1283 seq_printf(m, " oe:%d", info->icount.overrun);
1284 }
1285
1286 /* Append serial signal status to end */
1287 seq_printf(m, " %s\n", stat_buf+1);
1288
1289 seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1290 info->tx_active,info->bh_requested,info->bh_running,
1291 info->pending_bh);
1292}
1293
1294/* Called to print information about devices
1295 */
1296static int synclink_gt_proc_show(struct seq_file *m, void *v)
1297{
1298 struct slgt_info *info;
1299
1300 seq_puts(m, "synclink_gt driver\n");
1301
1302 info = slgt_device_list;
1303 while( info ) {
1304 line_info(m, info);
1305 info = info->next_device;
1306 }
1307 return 0;
1308}
1309
1310/*
1311 * return count of bytes in transmit buffer
1312 */
1313static int chars_in_buffer(struct tty_struct *tty)
1314{
1315 struct slgt_info *info = tty->driver_data;
1316 int count;
1317 if (sanity_check(info, tty->name, "chars_in_buffer"))
1318 return 0;
1319 count = tbuf_bytes(info);
1320 DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1321 return count;
1322}
1323
1324/*
1325 * signal remote device to throttle send data (our receive data)
1326 */
1327static void throttle(struct tty_struct * tty)
1328{
1329 struct slgt_info *info = tty->driver_data;
1330 unsigned long flags;
1331
1332 if (sanity_check(info, tty->name, "throttle"))
1333 return;
1334 DBGINFO(("%s throttle\n", info->device_name));
1335 if (I_IXOFF(tty))
1336 send_xchar(tty, STOP_CHAR(tty));
1337 if (C_CRTSCTS(tty)) {
1338 spin_lock_irqsave(&info->lock,flags);
1339 info->signals &= ~SerialSignal_RTS;
1340 set_signals(info);
1341 spin_unlock_irqrestore(&info->lock,flags);
1342 }
1343}
1344
1345/*
1346 * signal remote device to stop throttling send data (our receive data)
1347 */
1348static void unthrottle(struct tty_struct * tty)
1349{
1350 struct slgt_info *info = tty->driver_data;
1351 unsigned long flags;
1352
1353 if (sanity_check(info, tty->name, "unthrottle"))
1354 return;
1355 DBGINFO(("%s unthrottle\n", info->device_name));
1356 if (I_IXOFF(tty)) {
1357 if (info->x_char)
1358 info->x_char = 0;
1359 else
1360 send_xchar(tty, START_CHAR(tty));
1361 }
1362 if (C_CRTSCTS(tty)) {
1363 spin_lock_irqsave(&info->lock,flags);
1364 info->signals |= SerialSignal_RTS;
1365 set_signals(info);
1366 spin_unlock_irqrestore(&info->lock,flags);
1367 }
1368}
1369
1370/*
1371 * set or clear transmit break condition
1372 * break_state -1=set break condition, 0=clear
1373 */
1374static int set_break(struct tty_struct *tty, int break_state)
1375{
1376 struct slgt_info *info = tty->driver_data;
1377 unsigned short value;
1378 unsigned long flags;
1379
1380 if (sanity_check(info, tty->name, "set_break"))
1381 return -EINVAL;
1382 DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1383
1384 spin_lock_irqsave(&info->lock,flags);
1385 value = rd_reg16(info, TCR);
1386 if (break_state == -1)
1387 value |= BIT6;
1388 else
1389 value &= ~BIT6;
1390 wr_reg16(info, TCR, value);
1391 spin_unlock_irqrestore(&info->lock,flags);
1392 return 0;
1393}
1394
1395#if SYNCLINK_GENERIC_HDLC
1396
1397/**
1398 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1399 * set encoding and frame check sequence (FCS) options
1400 *
1401 * dev pointer to network device structure
1402 * encoding serial encoding setting
1403 * parity FCS setting
1404 *
1405 * returns 0 if success, otherwise error code
1406 */
1407static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1408 unsigned short parity)
1409{
1410 struct slgt_info *info = dev_to_port(dev);
1411 unsigned char new_encoding;
1412 unsigned short new_crctype;
1413
1414 /* return error if TTY interface open */
1415 if (info->port.count)
1416 return -EBUSY;
1417
1418 DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1419
1420 switch (encoding)
1421 {
1422 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break;
1423 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1424 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1425 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1426 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1427 default: return -EINVAL;
1428 }
1429
1430 switch (parity)
1431 {
1432 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break;
1433 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1434 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1435 default: return -EINVAL;
1436 }
1437
1438 info->params.encoding = new_encoding;
1439 info->params.crc_type = new_crctype;
1440
1441 /* if network interface up, reprogram hardware */
1442 if (info->netcount)
1443 program_hw(info);
1444
1445 return 0;
1446}
1447
1448/**
1449 * called by generic HDLC layer to send frame
1450 *
1451 * skb socket buffer containing HDLC frame
1452 * dev pointer to network device structure
1453 */
1454static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1455 struct net_device *dev)
1456{
1457 struct slgt_info *info = dev_to_port(dev);
1458 unsigned long flags;
1459
1460 DBGINFO(("%s hdlc_xmit\n", dev->name));
1461
1462 if (!skb->len)
1463 return NETDEV_TX_OK;
1464
1465 /* stop sending until this frame completes */
1466 netif_stop_queue(dev);
1467
1468 /* update network statistics */
1469 dev->stats.tx_packets++;
1470 dev->stats.tx_bytes += skb->len;
1471
1472 /* save start time for transmit timeout detection */
1473 netif_trans_update(dev);
1474
1475 spin_lock_irqsave(&info->lock, flags);
1476 tx_load(info, skb->data, skb->len);
1477 spin_unlock_irqrestore(&info->lock, flags);
1478
1479 /* done with socket buffer, so free it */
1480 dev_kfree_skb(skb);
1481
1482 return NETDEV_TX_OK;
1483}
1484
1485/**
1486 * called by network layer when interface enabled
1487 * claim resources and initialize hardware
1488 *
1489 * dev pointer to network device structure
1490 *
1491 * returns 0 if success, otherwise error code
1492 */
1493static int hdlcdev_open(struct net_device *dev)
1494{
1495 struct slgt_info *info = dev_to_port(dev);
1496 int rc;
1497 unsigned long flags;
1498
1499 if (!try_module_get(THIS_MODULE))
1500 return -EBUSY;
1501
1502 DBGINFO(("%s hdlcdev_open\n", dev->name));
1503
1504 /* generic HDLC layer open processing */
1505 rc = hdlc_open(dev);
1506 if (rc)
1507 return rc;
1508
1509 /* arbitrate between network and tty opens */
1510 spin_lock_irqsave(&info->netlock, flags);
1511 if (info->port.count != 0 || info->netcount != 0) {
1512 DBGINFO(("%s hdlc_open busy\n", dev->name));
1513 spin_unlock_irqrestore(&info->netlock, flags);
1514 return -EBUSY;
1515 }
1516 info->netcount=1;
1517 spin_unlock_irqrestore(&info->netlock, flags);
1518
1519 /* claim resources and init adapter */
1520 if ((rc = startup(info)) != 0) {
1521 spin_lock_irqsave(&info->netlock, flags);
1522 info->netcount=0;
1523 spin_unlock_irqrestore(&info->netlock, flags);
1524 return rc;
1525 }
1526
1527 /* assert RTS and DTR, apply hardware settings */
1528 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
1529 program_hw(info);
1530
1531 /* enable network layer transmit */
1532 netif_trans_update(dev);
1533 netif_start_queue(dev);
1534
1535 /* inform generic HDLC layer of current DCD status */
1536 spin_lock_irqsave(&info->lock, flags);
1537 get_signals(info);
1538 spin_unlock_irqrestore(&info->lock, flags);
1539 if (info->signals & SerialSignal_DCD)
1540 netif_carrier_on(dev);
1541 else
1542 netif_carrier_off(dev);
1543 return 0;
1544}
1545
1546/**
1547 * called by network layer when interface is disabled
1548 * shutdown hardware and release resources
1549 *
1550 * dev pointer to network device structure
1551 *
1552 * returns 0 if success, otherwise error code
1553 */
1554static int hdlcdev_close(struct net_device *dev)
1555{
1556 struct slgt_info *info = dev_to_port(dev);
1557 unsigned long flags;
1558
1559 DBGINFO(("%s hdlcdev_close\n", dev->name));
1560
1561 netif_stop_queue(dev);
1562
1563 /* shutdown adapter and release resources */
1564 shutdown(info);
1565
1566 hdlc_close(dev);
1567
1568 spin_lock_irqsave(&info->netlock, flags);
1569 info->netcount=0;
1570 spin_unlock_irqrestore(&info->netlock, flags);
1571
1572 module_put(THIS_MODULE);
1573 return 0;
1574}
1575
1576/**
1577 * called by network layer to process IOCTL call to network device
1578 *
1579 * dev pointer to network device structure
1580 * ifr pointer to network interface request structure
1581 * cmd IOCTL command code
1582 *
1583 * returns 0 if success, otherwise error code
1584 */
1585static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1586{
1587 const size_t size = sizeof(sync_serial_settings);
1588 sync_serial_settings new_line;
1589 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1590 struct slgt_info *info = dev_to_port(dev);
1591 unsigned int flags;
1592
1593 DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1594
1595 /* return error if TTY interface open */
1596 if (info->port.count)
1597 return -EBUSY;
1598
1599 if (cmd != SIOCWANDEV)
1600 return hdlc_ioctl(dev, ifr, cmd);
1601
1602 memset(&new_line, 0, sizeof(new_line));
1603
1604 switch(ifr->ifr_settings.type) {
1605 case IF_GET_IFACE: /* return current sync_serial_settings */
1606
1607 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1608 if (ifr->ifr_settings.size < size) {
1609 ifr->ifr_settings.size = size; /* data size wanted */
1610 return -ENOBUFS;
1611 }
1612
1613 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1614 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1615 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1616 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1617
1618 switch (flags){
1619 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1620 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break;
1621 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break;
1622 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1623 default: new_line.clock_type = CLOCK_DEFAULT;
1624 }
1625
1626 new_line.clock_rate = info->params.clock_speed;
1627 new_line.loopback = info->params.loopback ? 1:0;
1628
1629 if (copy_to_user(line, &new_line, size))
1630 return -EFAULT;
1631 return 0;
1632
1633 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1634
1635 if(!capable(CAP_NET_ADMIN))
1636 return -EPERM;
1637 if (copy_from_user(&new_line, line, size))
1638 return -EFAULT;
1639
1640 switch (new_line.clock_type)
1641 {
1642 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1643 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1644 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break;
1645 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break;
1646 case CLOCK_DEFAULT: flags = info->params.flags &
1647 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1648 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1649 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1650 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break;
1651 default: return -EINVAL;
1652 }
1653
1654 if (new_line.loopback != 0 && new_line.loopback != 1)
1655 return -EINVAL;
1656
1657 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1658 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1659 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1660 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1661 info->params.flags |= flags;
1662
1663 info->params.loopback = new_line.loopback;
1664
1665 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1666 info->params.clock_speed = new_line.clock_rate;
1667 else
1668 info->params.clock_speed = 0;
1669
1670 /* if network interface up, reprogram hardware */
1671 if (info->netcount)
1672 program_hw(info);
1673 return 0;
1674
1675 default:
1676 return hdlc_ioctl(dev, ifr, cmd);
1677 }
1678}
1679
1680/**
1681 * called by network layer when transmit timeout is detected
1682 *
1683 * dev pointer to network device structure
1684 */
1685static void hdlcdev_tx_timeout(struct net_device *dev, unsigned int txqueue)
1686{
1687 struct slgt_info *info = dev_to_port(dev);
1688 unsigned long flags;
1689
1690 DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1691
1692 dev->stats.tx_errors++;
1693 dev->stats.tx_aborted_errors++;
1694
1695 spin_lock_irqsave(&info->lock,flags);
1696 tx_stop(info);
1697 spin_unlock_irqrestore(&info->lock,flags);
1698
1699 netif_wake_queue(dev);
1700}
1701
1702/**
1703 * called by device driver when transmit completes
1704 * reenable network layer transmit if stopped
1705 *
1706 * info pointer to device instance information
1707 */
1708static void hdlcdev_tx_done(struct slgt_info *info)
1709{
1710 if (netif_queue_stopped(info->netdev))
1711 netif_wake_queue(info->netdev);
1712}
1713
1714/**
1715 * called by device driver when frame received
1716 * pass frame to network layer
1717 *
1718 * info pointer to device instance information
1719 * buf pointer to buffer contianing frame data
1720 * size count of data bytes in buf
1721 */
1722static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1723{
1724 struct sk_buff *skb = dev_alloc_skb(size);
1725 struct net_device *dev = info->netdev;
1726
1727 DBGINFO(("%s hdlcdev_rx\n", dev->name));
1728
1729 if (skb == NULL) {
1730 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1731 dev->stats.rx_dropped++;
1732 return;
1733 }
1734
1735 skb_put_data(skb, buf, size);
1736
1737 skb->protocol = hdlc_type_trans(skb, dev);
1738
1739 dev->stats.rx_packets++;
1740 dev->stats.rx_bytes += size;
1741
1742 netif_rx(skb);
1743}
1744
1745static const struct net_device_ops hdlcdev_ops = {
1746 .ndo_open = hdlcdev_open,
1747 .ndo_stop = hdlcdev_close,
1748 .ndo_start_xmit = hdlc_start_xmit,
1749 .ndo_do_ioctl = hdlcdev_ioctl,
1750 .ndo_tx_timeout = hdlcdev_tx_timeout,
1751};
1752
1753/**
1754 * called by device driver when adding device instance
1755 * do generic HDLC initialization
1756 *
1757 * info pointer to device instance information
1758 *
1759 * returns 0 if success, otherwise error code
1760 */
1761static int hdlcdev_init(struct slgt_info *info)
1762{
1763 int rc;
1764 struct net_device *dev;
1765 hdlc_device *hdlc;
1766
1767 /* allocate and initialize network and HDLC layer objects */
1768
1769 dev = alloc_hdlcdev(info);
1770 if (!dev) {
1771 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1772 return -ENOMEM;
1773 }
1774
1775 /* for network layer reporting purposes only */
1776 dev->mem_start = info->phys_reg_addr;
1777 dev->mem_end = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1778 dev->irq = info->irq_level;
1779
1780 /* network layer callbacks and settings */
1781 dev->netdev_ops = &hdlcdev_ops;
1782 dev->watchdog_timeo = 10 * HZ;
1783 dev->tx_queue_len = 50;
1784
1785 /* generic HDLC layer callbacks and settings */
1786 hdlc = dev_to_hdlc(dev);
1787 hdlc->attach = hdlcdev_attach;
1788 hdlc->xmit = hdlcdev_xmit;
1789
1790 /* register objects with HDLC layer */
1791 rc = register_hdlc_device(dev);
1792 if (rc) {
1793 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1794 free_netdev(dev);
1795 return rc;
1796 }
1797
1798 info->netdev = dev;
1799 return 0;
1800}
1801
1802/**
1803 * called by device driver when removing device instance
1804 * do generic HDLC cleanup
1805 *
1806 * info pointer to device instance information
1807 */
1808static void hdlcdev_exit(struct slgt_info *info)
1809{
1810 unregister_hdlc_device(info->netdev);
1811 free_netdev(info->netdev);
1812 info->netdev = NULL;
1813}
1814
1815#endif /* ifdef CONFIG_HDLC */
1816
1817/*
1818 * get async data from rx DMA buffers
1819 */
1820static void rx_async(struct slgt_info *info)
1821{
1822 struct mgsl_icount *icount = &info->icount;
1823 unsigned int start, end;
1824 unsigned char *p;
1825 unsigned char status;
1826 struct slgt_desc *bufs = info->rbufs;
1827 int i, count;
1828 int chars = 0;
1829 int stat;
1830 unsigned char ch;
1831
1832 start = end = info->rbuf_current;
1833
1834 while(desc_complete(bufs[end])) {
1835 count = desc_count(bufs[end]) - info->rbuf_index;
1836 p = bufs[end].buf + info->rbuf_index;
1837
1838 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1839 DBGDATA(info, p, count, "rx");
1840
1841 for(i=0 ; i < count; i+=2, p+=2) {
1842 ch = *p;
1843 icount->rx++;
1844
1845 stat = 0;
1846
1847 status = *(p + 1) & (BIT1 + BIT0);
1848 if (status) {
1849 if (status & BIT1)
1850 icount->parity++;
1851 else if (status & BIT0)
1852 icount->frame++;
1853 /* discard char if tty control flags say so */
1854 if (status & info->ignore_status_mask)
1855 continue;
1856 if (status & BIT1)
1857 stat = TTY_PARITY;
1858 else if (status & BIT0)
1859 stat = TTY_FRAME;
1860 }
1861 tty_insert_flip_char(&info->port, ch, stat);
1862 chars++;
1863 }
1864
1865 if (i < count) {
1866 /* receive buffer not completed */
1867 info->rbuf_index += i;
1868 mod_timer(&info->rx_timer, jiffies + 1);
1869 break;
1870 }
1871
1872 info->rbuf_index = 0;
1873 free_rbufs(info, end, end);
1874
1875 if (++end == info->rbuf_count)
1876 end = 0;
1877
1878 /* if entire list searched then no frame available */
1879 if (end == start)
1880 break;
1881 }
1882
1883 if (chars)
1884 tty_flip_buffer_push(&info->port);
1885}
1886
1887/*
1888 * return next bottom half action to perform
1889 */
1890static int bh_action(struct slgt_info *info)
1891{
1892 unsigned long flags;
1893 int rc;
1894
1895 spin_lock_irqsave(&info->lock,flags);
1896
1897 if (info->pending_bh & BH_RECEIVE) {
1898 info->pending_bh &= ~BH_RECEIVE;
1899 rc = BH_RECEIVE;
1900 } else if (info->pending_bh & BH_TRANSMIT) {
1901 info->pending_bh &= ~BH_TRANSMIT;
1902 rc = BH_TRANSMIT;
1903 } else if (info->pending_bh & BH_STATUS) {
1904 info->pending_bh &= ~BH_STATUS;
1905 rc = BH_STATUS;
1906 } else {
1907 /* Mark BH routine as complete */
1908 info->bh_running = false;
1909 info->bh_requested = false;
1910 rc = 0;
1911 }
1912
1913 spin_unlock_irqrestore(&info->lock,flags);
1914
1915 return rc;
1916}
1917
1918/*
1919 * perform bottom half processing
1920 */
1921static void bh_handler(struct work_struct *work)
1922{
1923 struct slgt_info *info = container_of(work, struct slgt_info, task);
1924 int action;
1925
1926 info->bh_running = true;
1927
1928 while((action = bh_action(info))) {
1929 switch (action) {
1930 case BH_RECEIVE:
1931 DBGBH(("%s bh receive\n", info->device_name));
1932 switch(info->params.mode) {
1933 case MGSL_MODE_ASYNC:
1934 rx_async(info);
1935 break;
1936 case MGSL_MODE_HDLC:
1937 while(rx_get_frame(info));
1938 break;
1939 case MGSL_MODE_RAW:
1940 case MGSL_MODE_MONOSYNC:
1941 case MGSL_MODE_BISYNC:
1942 case MGSL_MODE_XSYNC:
1943 while(rx_get_buf(info));
1944 break;
1945 }
1946 /* restart receiver if rx DMA buffers exhausted */
1947 if (info->rx_restart)
1948 rx_start(info);
1949 break;
1950 case BH_TRANSMIT:
1951 bh_transmit(info);
1952 break;
1953 case BH_STATUS:
1954 DBGBH(("%s bh status\n", info->device_name));
1955 info->ri_chkcount = 0;
1956 info->dsr_chkcount = 0;
1957 info->dcd_chkcount = 0;
1958 info->cts_chkcount = 0;
1959 break;
1960 default:
1961 DBGBH(("%s unknown action\n", info->device_name));
1962 break;
1963 }
1964 }
1965 DBGBH(("%s bh_handler exit\n", info->device_name));
1966}
1967
1968static void bh_transmit(struct slgt_info *info)
1969{
1970 struct tty_struct *tty = info->port.tty;
1971
1972 DBGBH(("%s bh_transmit\n", info->device_name));
1973 if (tty)
1974 tty_wakeup(tty);
1975}
1976
1977static void dsr_change(struct slgt_info *info, unsigned short status)
1978{
1979 if (status & BIT3) {
1980 info->signals |= SerialSignal_DSR;
1981 info->input_signal_events.dsr_up++;
1982 } else {
1983 info->signals &= ~SerialSignal_DSR;
1984 info->input_signal_events.dsr_down++;
1985 }
1986 DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1987 if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1988 slgt_irq_off(info, IRQ_DSR);
1989 return;
1990 }
1991 info->icount.dsr++;
1992 wake_up_interruptible(&info->status_event_wait_q);
1993 wake_up_interruptible(&info->event_wait_q);
1994 info->pending_bh |= BH_STATUS;
1995}
1996
1997static void cts_change(struct slgt_info *info, unsigned short status)
1998{
1999 if (status & BIT2) {
2000 info->signals |= SerialSignal_CTS;
2001 info->input_signal_events.cts_up++;
2002 } else {
2003 info->signals &= ~SerialSignal_CTS;
2004 info->input_signal_events.cts_down++;
2005 }
2006 DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2007 if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2008 slgt_irq_off(info, IRQ_CTS);
2009 return;
2010 }
2011 info->icount.cts++;
2012 wake_up_interruptible(&info->status_event_wait_q);
2013 wake_up_interruptible(&info->event_wait_q);
2014 info->pending_bh |= BH_STATUS;
2015
2016 if (tty_port_cts_enabled(&info->port)) {
2017 if (info->port.tty) {
2018 if (info->port.tty->hw_stopped) {
2019 if (info->signals & SerialSignal_CTS) {
2020 info->port.tty->hw_stopped = 0;
2021 info->pending_bh |= BH_TRANSMIT;
2022 return;
2023 }
2024 } else {
2025 if (!(info->signals & SerialSignal_CTS))
2026 info->port.tty->hw_stopped = 1;
2027 }
2028 }
2029 }
2030}
2031
2032static void dcd_change(struct slgt_info *info, unsigned short status)
2033{
2034 if (status & BIT1) {
2035 info->signals |= SerialSignal_DCD;
2036 info->input_signal_events.dcd_up++;
2037 } else {
2038 info->signals &= ~SerialSignal_DCD;
2039 info->input_signal_events.dcd_down++;
2040 }
2041 DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2042 if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2043 slgt_irq_off(info, IRQ_DCD);
2044 return;
2045 }
2046 info->icount.dcd++;
2047#if SYNCLINK_GENERIC_HDLC
2048 if (info->netcount) {
2049 if (info->signals & SerialSignal_DCD)
2050 netif_carrier_on(info->netdev);
2051 else
2052 netif_carrier_off(info->netdev);
2053 }
2054#endif
2055 wake_up_interruptible(&info->status_event_wait_q);
2056 wake_up_interruptible(&info->event_wait_q);
2057 info->pending_bh |= BH_STATUS;
2058
2059 if (tty_port_check_carrier(&info->port)) {
2060 if (info->signals & SerialSignal_DCD)
2061 wake_up_interruptible(&info->port.open_wait);
2062 else {
2063 if (info->port.tty)
2064 tty_hangup(info->port.tty);
2065 }
2066 }
2067}
2068
2069static void ri_change(struct slgt_info *info, unsigned short status)
2070{
2071 if (status & BIT0) {
2072 info->signals |= SerialSignal_RI;
2073 info->input_signal_events.ri_up++;
2074 } else {
2075 info->signals &= ~SerialSignal_RI;
2076 info->input_signal_events.ri_down++;
2077 }
2078 DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2079 if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2080 slgt_irq_off(info, IRQ_RI);
2081 return;
2082 }
2083 info->icount.rng++;
2084 wake_up_interruptible(&info->status_event_wait_q);
2085 wake_up_interruptible(&info->event_wait_q);
2086 info->pending_bh |= BH_STATUS;
2087}
2088
2089static void isr_rxdata(struct slgt_info *info)
2090{
2091 unsigned int count = info->rbuf_fill_count;
2092 unsigned int i = info->rbuf_fill_index;
2093 unsigned short reg;
2094
2095 while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2096 reg = rd_reg16(info, RDR);
2097 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2098 if (desc_complete(info->rbufs[i])) {
2099 /* all buffers full */
2100 rx_stop(info);
2101 info->rx_restart = true;
2102 continue;
2103 }
2104 info->rbufs[i].buf[count++] = (unsigned char)reg;
2105 /* async mode saves status byte to buffer for each data byte */
2106 if (info->params.mode == MGSL_MODE_ASYNC)
2107 info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2108 if (count == info->rbuf_fill_level || (reg & BIT10)) {
2109 /* buffer full or end of frame */
2110 set_desc_count(info->rbufs[i], count);
2111 set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2112 info->rbuf_fill_count = count = 0;
2113 if (++i == info->rbuf_count)
2114 i = 0;
2115 info->pending_bh |= BH_RECEIVE;
2116 }
2117 }
2118
2119 info->rbuf_fill_index = i;
2120 info->rbuf_fill_count = count;
2121}
2122
2123static void isr_serial(struct slgt_info *info)
2124{
2125 unsigned short status = rd_reg16(info, SSR);
2126
2127 DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2128
2129 wr_reg16(info, SSR, status); /* clear pending */
2130
2131 info->irq_occurred = true;
2132
2133 if (info->params.mode == MGSL_MODE_ASYNC) {
2134 if (status & IRQ_TXIDLE) {
2135 if (info->tx_active)
2136 isr_txeom(info, status);
2137 }
2138 if (info->rx_pio && (status & IRQ_RXDATA))
2139 isr_rxdata(info);
2140 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2141 info->icount.brk++;
2142 /* process break detection if tty control allows */
2143 if (info->port.tty) {
2144 if (!(status & info->ignore_status_mask)) {
2145 if (info->read_status_mask & MASK_BREAK) {
2146 tty_insert_flip_char(&info->port, 0, TTY_BREAK);
2147 if (info->port.flags & ASYNC_SAK)
2148 do_SAK(info->port.tty);
2149 }
2150 }
2151 }
2152 }
2153 } else {
2154 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2155 isr_txeom(info, status);
2156 if (info->rx_pio && (status & IRQ_RXDATA))
2157 isr_rxdata(info);
2158 if (status & IRQ_RXIDLE) {
2159 if (status & RXIDLE)
2160 info->icount.rxidle++;
2161 else
2162 info->icount.exithunt++;
2163 wake_up_interruptible(&info->event_wait_q);
2164 }
2165
2166 if (status & IRQ_RXOVER)
2167 rx_start(info);
2168 }
2169
2170 if (status & IRQ_DSR)
2171 dsr_change(info, status);
2172 if (status & IRQ_CTS)
2173 cts_change(info, status);
2174 if (status & IRQ_DCD)
2175 dcd_change(info, status);
2176 if (status & IRQ_RI)
2177 ri_change(info, status);
2178}
2179
2180static void isr_rdma(struct slgt_info *info)
2181{
2182 unsigned int status = rd_reg32(info, RDCSR);
2183
2184 DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2185
2186 /* RDCSR (rx DMA control/status)
2187 *
2188 * 31..07 reserved
2189 * 06 save status byte to DMA buffer
2190 * 05 error
2191 * 04 eol (end of list)
2192 * 03 eob (end of buffer)
2193 * 02 IRQ enable
2194 * 01 reset
2195 * 00 enable
2196 */
2197 wr_reg32(info, RDCSR, status); /* clear pending */
2198
2199 if (status & (BIT5 + BIT4)) {
2200 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2201 info->rx_restart = true;
2202 }
2203 info->pending_bh |= BH_RECEIVE;
2204}
2205
2206static void isr_tdma(struct slgt_info *info)
2207{
2208 unsigned int status = rd_reg32(info, TDCSR);
2209
2210 DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2211
2212 /* TDCSR (tx DMA control/status)
2213 *
2214 * 31..06 reserved
2215 * 05 error
2216 * 04 eol (end of list)
2217 * 03 eob (end of buffer)
2218 * 02 IRQ enable
2219 * 01 reset
2220 * 00 enable
2221 */
2222 wr_reg32(info, TDCSR, status); /* clear pending */
2223
2224 if (status & (BIT5 + BIT4 + BIT3)) {
2225 // another transmit buffer has completed
2226 // run bottom half to get more send data from user
2227 info->pending_bh |= BH_TRANSMIT;
2228 }
2229}
2230
2231/*
2232 * return true if there are unsent tx DMA buffers, otherwise false
2233 *
2234 * if there are unsent buffers then info->tbuf_start
2235 * is set to index of first unsent buffer
2236 */
2237static bool unsent_tbufs(struct slgt_info *info)
2238{
2239 unsigned int i = info->tbuf_current;
2240 bool rc = false;
2241
2242 /*
2243 * search backwards from last loaded buffer (precedes tbuf_current)
2244 * for first unsent buffer (desc_count > 0)
2245 */
2246
2247 do {
2248 if (i)
2249 i--;
2250 else
2251 i = info->tbuf_count - 1;
2252 if (!desc_count(info->tbufs[i]))
2253 break;
2254 info->tbuf_start = i;
2255 rc = true;
2256 } while (i != info->tbuf_current);
2257
2258 return rc;
2259}
2260
2261static void isr_txeom(struct slgt_info *info, unsigned short status)
2262{
2263 DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2264
2265 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2266 tdma_reset(info);
2267 if (status & IRQ_TXUNDER) {
2268 unsigned short val = rd_reg16(info, TCR);
2269 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2270 wr_reg16(info, TCR, val); /* clear reset bit */
2271 }
2272
2273 if (info->tx_active) {
2274 if (info->params.mode != MGSL_MODE_ASYNC) {
2275 if (status & IRQ_TXUNDER)
2276 info->icount.txunder++;
2277 else if (status & IRQ_TXIDLE)
2278 info->icount.txok++;
2279 }
2280
2281 if (unsent_tbufs(info)) {
2282 tx_start(info);
2283 update_tx_timer(info);
2284 return;
2285 }
2286 info->tx_active = false;
2287
2288 del_timer(&info->tx_timer);
2289
2290 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2291 info->signals &= ~SerialSignal_RTS;
2292 info->drop_rts_on_tx_done = false;
2293 set_signals(info);
2294 }
2295
2296#if SYNCLINK_GENERIC_HDLC
2297 if (info->netcount)
2298 hdlcdev_tx_done(info);
2299 else
2300#endif
2301 {
2302 if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2303 tx_stop(info);
2304 return;
2305 }
2306 info->pending_bh |= BH_TRANSMIT;
2307 }
2308 }
2309}
2310
2311static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2312{
2313 struct cond_wait *w, *prev;
2314
2315 /* wake processes waiting for specific transitions */
2316 for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2317 if (w->data & changed) {
2318 w->data = state;
2319 wake_up_interruptible(&w->q);
2320 if (prev != NULL)
2321 prev->next = w->next;
2322 else
2323 info->gpio_wait_q = w->next;
2324 } else
2325 prev = w;
2326 }
2327}
2328
2329/* interrupt service routine
2330 *
2331 * irq interrupt number
2332 * dev_id device ID supplied during interrupt registration
2333 */
2334static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2335{
2336 struct slgt_info *info = dev_id;
2337 unsigned int gsr;
2338 unsigned int i;
2339
2340 DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2341
2342 while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2343 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2344 info->irq_occurred = true;
2345 for(i=0; i < info->port_count ; i++) {
2346 if (info->port_array[i] == NULL)
2347 continue;
2348 spin_lock(&info->port_array[i]->lock);
2349 if (gsr & (BIT8 << i))
2350 isr_serial(info->port_array[i]);
2351 if (gsr & (BIT16 << (i*2)))
2352 isr_rdma(info->port_array[i]);
2353 if (gsr & (BIT17 << (i*2)))
2354 isr_tdma(info->port_array[i]);
2355 spin_unlock(&info->port_array[i]->lock);
2356 }
2357 }
2358
2359 if (info->gpio_present) {
2360 unsigned int state;
2361 unsigned int changed;
2362 spin_lock(&info->lock);
2363 while ((changed = rd_reg32(info, IOSR)) != 0) {
2364 DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2365 /* read latched state of GPIO signals */
2366 state = rd_reg32(info, IOVR);
2367 /* clear pending GPIO interrupt bits */
2368 wr_reg32(info, IOSR, changed);
2369 for (i=0 ; i < info->port_count ; i++) {
2370 if (info->port_array[i] != NULL)
2371 isr_gpio(info->port_array[i], changed, state);
2372 }
2373 }
2374 spin_unlock(&info->lock);
2375 }
2376
2377 for(i=0; i < info->port_count ; i++) {
2378 struct slgt_info *port = info->port_array[i];
2379 if (port == NULL)
2380 continue;
2381 spin_lock(&port->lock);
2382 if ((port->port.count || port->netcount) &&
2383 port->pending_bh && !port->bh_running &&
2384 !port->bh_requested) {
2385 DBGISR(("%s bh queued\n", port->device_name));
2386 schedule_work(&port->task);
2387 port->bh_requested = true;
2388 }
2389 spin_unlock(&port->lock);
2390 }
2391
2392 DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2393 return IRQ_HANDLED;
2394}
2395
2396static int startup(struct slgt_info *info)
2397{
2398 DBGINFO(("%s startup\n", info->device_name));
2399
2400 if (tty_port_initialized(&info->port))
2401 return 0;
2402
2403 if (!info->tx_buf) {
2404 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2405 if (!info->tx_buf) {
2406 DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2407 return -ENOMEM;
2408 }
2409 }
2410
2411 info->pending_bh = 0;
2412
2413 memset(&info->icount, 0, sizeof(info->icount));
2414
2415 /* program hardware for current parameters */
2416 change_params(info);
2417
2418 if (info->port.tty)
2419 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2420
2421 tty_port_set_initialized(&info->port, 1);
2422
2423 return 0;
2424}
2425
2426/*
2427 * called by close() and hangup() to shutdown hardware
2428 */
2429static void shutdown(struct slgt_info *info)
2430{
2431 unsigned long flags;
2432
2433 if (!tty_port_initialized(&info->port))
2434 return;
2435
2436 DBGINFO(("%s shutdown\n", info->device_name));
2437
2438 /* clear status wait queue because status changes */
2439 /* can't happen after shutting down the hardware */
2440 wake_up_interruptible(&info->status_event_wait_q);
2441 wake_up_interruptible(&info->event_wait_q);
2442
2443 del_timer_sync(&info->tx_timer);
2444 del_timer_sync(&info->rx_timer);
2445
2446 kfree(info->tx_buf);
2447 info->tx_buf = NULL;
2448
2449 spin_lock_irqsave(&info->lock,flags);
2450
2451 tx_stop(info);
2452 rx_stop(info);
2453
2454 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2455
2456 if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
2457 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2458 set_signals(info);
2459 }
2460
2461 flush_cond_wait(&info->gpio_wait_q);
2462
2463 spin_unlock_irqrestore(&info->lock,flags);
2464
2465 if (info->port.tty)
2466 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2467
2468 tty_port_set_initialized(&info->port, 0);
2469}
2470
2471static void program_hw(struct slgt_info *info)
2472{
2473 unsigned long flags;
2474
2475 spin_lock_irqsave(&info->lock,flags);
2476
2477 rx_stop(info);
2478 tx_stop(info);
2479
2480 if (info->params.mode != MGSL_MODE_ASYNC ||
2481 info->netcount)
2482 sync_mode(info);
2483 else
2484 async_mode(info);
2485
2486 set_signals(info);
2487
2488 info->dcd_chkcount = 0;
2489 info->cts_chkcount = 0;
2490 info->ri_chkcount = 0;
2491 info->dsr_chkcount = 0;
2492
2493 slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2494 get_signals(info);
2495
2496 if (info->netcount ||
2497 (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
2498 rx_start(info);
2499
2500 spin_unlock_irqrestore(&info->lock,flags);
2501}
2502
2503/*
2504 * reconfigure adapter based on new parameters
2505 */
2506static void change_params(struct slgt_info *info)
2507{
2508 unsigned cflag;
2509 int bits_per_char;
2510
2511 if (!info->port.tty)
2512 return;
2513 DBGINFO(("%s change_params\n", info->device_name));
2514
2515 cflag = info->port.tty->termios.c_cflag;
2516
2517 /* if B0 rate (hangup) specified then negate RTS and DTR */
2518 /* otherwise assert RTS and DTR */
2519 if (cflag & CBAUD)
2520 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
2521 else
2522 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2523
2524 /* byte size and parity */
2525
2526 switch (cflag & CSIZE) {
2527 case CS5: info->params.data_bits = 5; break;
2528 case CS6: info->params.data_bits = 6; break;
2529 case CS7: info->params.data_bits = 7; break;
2530 case CS8: info->params.data_bits = 8; break;
2531 default: info->params.data_bits = 7; break;
2532 }
2533
2534 info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2535
2536 if (cflag & PARENB)
2537 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2538 else
2539 info->params.parity = ASYNC_PARITY_NONE;
2540
2541 /* calculate number of jiffies to transmit a full
2542 * FIFO (32 bytes) at specified data rate
2543 */
2544 bits_per_char = info->params.data_bits +
2545 info->params.stop_bits + 1;
2546
2547 info->params.data_rate = tty_get_baud_rate(info->port.tty);
2548
2549 if (info->params.data_rate) {
2550 info->timeout = (32*HZ*bits_per_char) /
2551 info->params.data_rate;
2552 }
2553 info->timeout += HZ/50; /* Add .02 seconds of slop */
2554
2555 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
2556 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
2557
2558 /* process tty input control flags */
2559
2560 info->read_status_mask = IRQ_RXOVER;
2561 if (I_INPCK(info->port.tty))
2562 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2563 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2564 info->read_status_mask |= MASK_BREAK;
2565 if (I_IGNPAR(info->port.tty))
2566 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2567 if (I_IGNBRK(info->port.tty)) {
2568 info->ignore_status_mask |= MASK_BREAK;
2569 /* If ignoring parity and break indicators, ignore
2570 * overruns too. (For real raw support).
2571 */
2572 if (I_IGNPAR(info->port.tty))
2573 info->ignore_status_mask |= MASK_OVERRUN;
2574 }
2575
2576 program_hw(info);
2577}
2578
2579static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2580{
2581 DBGINFO(("%s get_stats\n", info->device_name));
2582 if (!user_icount) {
2583 memset(&info->icount, 0, sizeof(info->icount));
2584 } else {
2585 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2586 return -EFAULT;
2587 }
2588 return 0;
2589}
2590
2591static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2592{
2593 DBGINFO(("%s get_params\n", info->device_name));
2594 if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2595 return -EFAULT;
2596 return 0;
2597}
2598
2599static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2600{
2601 unsigned long flags;
2602 MGSL_PARAMS tmp_params;
2603
2604 DBGINFO(("%s set_params\n", info->device_name));
2605 if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2606 return -EFAULT;
2607
2608 spin_lock_irqsave(&info->lock, flags);
2609 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2610 info->base_clock = tmp_params.clock_speed;
2611 else
2612 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2613 spin_unlock_irqrestore(&info->lock, flags);
2614
2615 program_hw(info);
2616
2617 return 0;
2618}
2619
2620static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2621{
2622 DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2623 if (put_user(info->idle_mode, idle_mode))
2624 return -EFAULT;
2625 return 0;
2626}
2627
2628static int set_txidle(struct slgt_info *info, int idle_mode)
2629{
2630 unsigned long flags;
2631 DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2632 spin_lock_irqsave(&info->lock,flags);
2633 info->idle_mode = idle_mode;
2634 if (info->params.mode != MGSL_MODE_ASYNC)
2635 tx_set_idle(info);
2636 spin_unlock_irqrestore(&info->lock,flags);
2637 return 0;
2638}
2639
2640static int tx_enable(struct slgt_info *info, int enable)
2641{
2642 unsigned long flags;
2643 DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2644 spin_lock_irqsave(&info->lock,flags);
2645 if (enable) {
2646 if (!info->tx_enabled)
2647 tx_start(info);
2648 } else {
2649 if (info->tx_enabled)
2650 tx_stop(info);
2651 }
2652 spin_unlock_irqrestore(&info->lock,flags);
2653 return 0;
2654}
2655
2656/*
2657 * abort transmit HDLC frame
2658 */
2659static int tx_abort(struct slgt_info *info)
2660{
2661 unsigned long flags;
2662 DBGINFO(("%s tx_abort\n", info->device_name));
2663 spin_lock_irqsave(&info->lock,flags);
2664 tdma_reset(info);
2665 spin_unlock_irqrestore(&info->lock,flags);
2666 return 0;
2667}
2668
2669static int rx_enable(struct slgt_info *info, int enable)
2670{
2671 unsigned long flags;
2672 unsigned int rbuf_fill_level;
2673 DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2674 spin_lock_irqsave(&info->lock,flags);
2675 /*
2676 * enable[31..16] = receive DMA buffer fill level
2677 * 0 = noop (leave fill level unchanged)
2678 * fill level must be multiple of 4 and <= buffer size
2679 */
2680 rbuf_fill_level = ((unsigned int)enable) >> 16;
2681 if (rbuf_fill_level) {
2682 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2683 spin_unlock_irqrestore(&info->lock, flags);
2684 return -EINVAL;
2685 }
2686 info->rbuf_fill_level = rbuf_fill_level;
2687 if (rbuf_fill_level < 128)
2688 info->rx_pio = 1; /* PIO mode */
2689 else
2690 info->rx_pio = 0; /* DMA mode */
2691 rx_stop(info); /* restart receiver to use new fill level */
2692 }
2693
2694 /*
2695 * enable[1..0] = receiver enable command
2696 * 0 = disable
2697 * 1 = enable
2698 * 2 = enable or force hunt mode if already enabled
2699 */
2700 enable &= 3;
2701 if (enable) {
2702 if (!info->rx_enabled)
2703 rx_start(info);
2704 else if (enable == 2) {
2705 /* force hunt mode (write 1 to RCR[3]) */
2706 wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2707 }
2708 } else {
2709 if (info->rx_enabled)
2710 rx_stop(info);
2711 }
2712 spin_unlock_irqrestore(&info->lock,flags);
2713 return 0;
2714}
2715
2716/*
2717 * wait for specified event to occur
2718 */
2719static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2720{
2721 unsigned long flags;
2722 int s;
2723 int rc=0;
2724 struct mgsl_icount cprev, cnow;
2725 int events;
2726 int mask;
2727 struct _input_signal_events oldsigs, newsigs;
2728 DECLARE_WAITQUEUE(wait, current);
2729
2730 if (get_user(mask, mask_ptr))
2731 return -EFAULT;
2732
2733 DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2734
2735 spin_lock_irqsave(&info->lock,flags);
2736
2737 /* return immediately if state matches requested events */
2738 get_signals(info);
2739 s = info->signals;
2740
2741 events = mask &
2742 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2743 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2744 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2745 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2746 if (events) {
2747 spin_unlock_irqrestore(&info->lock,flags);
2748 goto exit;
2749 }
2750
2751 /* save current irq counts */
2752 cprev = info->icount;
2753 oldsigs = info->input_signal_events;
2754
2755 /* enable hunt and idle irqs if needed */
2756 if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2757 unsigned short val = rd_reg16(info, SCR);
2758 if (!(val & IRQ_RXIDLE))
2759 wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2760 }
2761
2762 set_current_state(TASK_INTERRUPTIBLE);
2763 add_wait_queue(&info->event_wait_q, &wait);
2764
2765 spin_unlock_irqrestore(&info->lock,flags);
2766
2767 for(;;) {
2768 schedule();
2769 if (signal_pending(current)) {
2770 rc = -ERESTARTSYS;
2771 break;
2772 }
2773
2774 /* get current irq counts */
2775 spin_lock_irqsave(&info->lock,flags);
2776 cnow = info->icount;
2777 newsigs = info->input_signal_events;
2778 set_current_state(TASK_INTERRUPTIBLE);
2779 spin_unlock_irqrestore(&info->lock,flags);
2780
2781 /* if no change, wait aborted for some reason */
2782 if (newsigs.dsr_up == oldsigs.dsr_up &&
2783 newsigs.dsr_down == oldsigs.dsr_down &&
2784 newsigs.dcd_up == oldsigs.dcd_up &&
2785 newsigs.dcd_down == oldsigs.dcd_down &&
2786 newsigs.cts_up == oldsigs.cts_up &&
2787 newsigs.cts_down == oldsigs.cts_down &&
2788 newsigs.ri_up == oldsigs.ri_up &&
2789 newsigs.ri_down == oldsigs.ri_down &&
2790 cnow.exithunt == cprev.exithunt &&
2791 cnow.rxidle == cprev.rxidle) {
2792 rc = -EIO;
2793 break;
2794 }
2795
2796 events = mask &
2797 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) +
2798 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2799 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) +
2800 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2801 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) +
2802 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2803 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) +
2804 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) +
2805 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) +
2806 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) );
2807 if (events)
2808 break;
2809
2810 cprev = cnow;
2811 oldsigs = newsigs;
2812 }
2813
2814 remove_wait_queue(&info->event_wait_q, &wait);
2815 set_current_state(TASK_RUNNING);
2816
2817
2818 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2819 spin_lock_irqsave(&info->lock,flags);
2820 if (!waitqueue_active(&info->event_wait_q)) {
2821 /* disable enable exit hunt mode/idle rcvd IRQs */
2822 wr_reg16(info, SCR,
2823 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2824 }
2825 spin_unlock_irqrestore(&info->lock,flags);
2826 }
2827exit:
2828 if (rc == 0)
2829 rc = put_user(events, mask_ptr);
2830 return rc;
2831}
2832
2833static int get_interface(struct slgt_info *info, int __user *if_mode)
2834{
2835 DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2836 if (put_user(info->if_mode, if_mode))
2837 return -EFAULT;
2838 return 0;
2839}
2840
2841static int set_interface(struct slgt_info *info, int if_mode)
2842{
2843 unsigned long flags;
2844 unsigned short val;
2845
2846 DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2847 spin_lock_irqsave(&info->lock,flags);
2848 info->if_mode = if_mode;
2849
2850 msc_set_vcr(info);
2851
2852 /* TCR (tx control) 07 1=RTS driver control */
2853 val = rd_reg16(info, TCR);
2854 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2855 val |= BIT7;
2856 else
2857 val &= ~BIT7;
2858 wr_reg16(info, TCR, val);
2859
2860 spin_unlock_irqrestore(&info->lock,flags);
2861 return 0;
2862}
2863
2864static int get_xsync(struct slgt_info *info, int __user *xsync)
2865{
2866 DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2867 if (put_user(info->xsync, xsync))
2868 return -EFAULT;
2869 return 0;
2870}
2871
2872/*
2873 * set extended sync pattern (1 to 4 bytes) for extended sync mode
2874 *
2875 * sync pattern is contained in least significant bytes of value
2876 * most significant byte of sync pattern is oldest (1st sent/detected)
2877 */
2878static int set_xsync(struct slgt_info *info, int xsync)
2879{
2880 unsigned long flags;
2881
2882 DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2883 spin_lock_irqsave(&info->lock, flags);
2884 info->xsync = xsync;
2885 wr_reg32(info, XSR, xsync);
2886 spin_unlock_irqrestore(&info->lock, flags);
2887 return 0;
2888}
2889
2890static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2891{
2892 DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2893 if (put_user(info->xctrl, xctrl))
2894 return -EFAULT;
2895 return 0;
2896}
2897
2898/*
2899 * set extended control options
2900 *
2901 * xctrl[31:19] reserved, must be zero
2902 * xctrl[18:17] extended sync pattern length in bytes
2903 * 00 = 1 byte in xsr[7:0]
2904 * 01 = 2 bytes in xsr[15:0]
2905 * 10 = 3 bytes in xsr[23:0]
2906 * 11 = 4 bytes in xsr[31:0]
2907 * xctrl[16] 1 = enable terminal count, 0=disabled
2908 * xctrl[15:0] receive terminal count for fixed length packets
2909 * value is count minus one (0 = 1 byte packet)
2910 * when terminal count is reached, receiver
2911 * automatically returns to hunt mode and receive
2912 * FIFO contents are flushed to DMA buffers with
2913 * end of frame (EOF) status
2914 */
2915static int set_xctrl(struct slgt_info *info, int xctrl)
2916{
2917 unsigned long flags;
2918
2919 DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2920 spin_lock_irqsave(&info->lock, flags);
2921 info->xctrl = xctrl;
2922 wr_reg32(info, XCR, xctrl);
2923 spin_unlock_irqrestore(&info->lock, flags);
2924 return 0;
2925}
2926
2927/*
2928 * set general purpose IO pin state and direction
2929 *
2930 * user_gpio fields:
2931 * state each bit indicates a pin state
2932 * smask set bit indicates pin state to set
2933 * dir each bit indicates a pin direction (0=input, 1=output)
2934 * dmask set bit indicates pin direction to set
2935 */
2936static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2937{
2938 unsigned long flags;
2939 struct gpio_desc gpio;
2940 __u32 data;
2941
2942 if (!info->gpio_present)
2943 return -EINVAL;
2944 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2945 return -EFAULT;
2946 DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2947 info->device_name, gpio.state, gpio.smask,
2948 gpio.dir, gpio.dmask));
2949
2950 spin_lock_irqsave(&info->port_array[0]->lock, flags);
2951 if (gpio.dmask) {
2952 data = rd_reg32(info, IODR);
2953 data |= gpio.dmask & gpio.dir;
2954 data &= ~(gpio.dmask & ~gpio.dir);
2955 wr_reg32(info, IODR, data);
2956 }
2957 if (gpio.smask) {
2958 data = rd_reg32(info, IOVR);
2959 data |= gpio.smask & gpio.state;
2960 data &= ~(gpio.smask & ~gpio.state);
2961 wr_reg32(info, IOVR, data);
2962 }
2963 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
2964
2965 return 0;
2966}
2967
2968/*
2969 * get general purpose IO pin state and direction
2970 */
2971static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2972{
2973 struct gpio_desc gpio;
2974 if (!info->gpio_present)
2975 return -EINVAL;
2976 gpio.state = rd_reg32(info, IOVR);
2977 gpio.smask = 0xffffffff;
2978 gpio.dir = rd_reg32(info, IODR);
2979 gpio.dmask = 0xffffffff;
2980 if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2981 return -EFAULT;
2982 DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2983 info->device_name, gpio.state, gpio.dir));
2984 return 0;
2985}
2986
2987/*
2988 * conditional wait facility
2989 */
2990static void init_cond_wait(struct cond_wait *w, unsigned int data)
2991{
2992 init_waitqueue_head(&w->q);
2993 init_waitqueue_entry(&w->wait, current);
2994 w->data = data;
2995}
2996
2997static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2998{
2999 set_current_state(TASK_INTERRUPTIBLE);
3000 add_wait_queue(&w->q, &w->wait);
3001 w->next = *head;
3002 *head = w;
3003}
3004
3005static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
3006{
3007 struct cond_wait *w, *prev;
3008 remove_wait_queue(&cw->q, &cw->wait);
3009 set_current_state(TASK_RUNNING);
3010 for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
3011 if (w == cw) {
3012 if (prev != NULL)
3013 prev->next = w->next;
3014 else
3015 *head = w->next;
3016 break;
3017 }
3018 }
3019}
3020
3021static void flush_cond_wait(struct cond_wait **head)
3022{
3023 while (*head != NULL) {
3024 wake_up_interruptible(&(*head)->q);
3025 *head = (*head)->next;
3026 }
3027}
3028
3029/*
3030 * wait for general purpose I/O pin(s) to enter specified state
3031 *
3032 * user_gpio fields:
3033 * state - bit indicates target pin state
3034 * smask - set bit indicates watched pin
3035 *
3036 * The wait ends when at least one watched pin enters the specified
3037 * state. When 0 (no error) is returned, user_gpio->state is set to the
3038 * state of all GPIO pins when the wait ends.
3039 *
3040 * Note: Each pin may be a dedicated input, dedicated output, or
3041 * configurable input/output. The number and configuration of pins
3042 * varies with the specific adapter model. Only input pins (dedicated
3043 * or configured) can be monitored with this function.
3044 */
3045static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3046{
3047 unsigned long flags;
3048 int rc = 0;
3049 struct gpio_desc gpio;
3050 struct cond_wait wait;
3051 u32 state;
3052
3053 if (!info->gpio_present)
3054 return -EINVAL;
3055 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
3056 return -EFAULT;
3057 DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
3058 info->device_name, gpio.state, gpio.smask));
3059 /* ignore output pins identified by set IODR bit */
3060 if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
3061 return -EINVAL;
3062 init_cond_wait(&wait, gpio.smask);
3063
3064 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3065 /* enable interrupts for watched pins */
3066 wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3067 /* get current pin states */
3068 state = rd_reg32(info, IOVR);
3069
3070 if (gpio.smask & ~(state ^ gpio.state)) {
3071 /* already in target state */
3072 gpio.state = state;
3073 } else {
3074 /* wait for target state */
3075 add_cond_wait(&info->gpio_wait_q, &wait);
3076 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3077 schedule();
3078 if (signal_pending(current))
3079 rc = -ERESTARTSYS;
3080 else
3081 gpio.state = wait.data;
3082 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3083 remove_cond_wait(&info->gpio_wait_q, &wait);
3084 }
3085
3086 /* disable all GPIO interrupts if no waiting processes */
3087 if (info->gpio_wait_q == NULL)
3088 wr_reg32(info, IOER, 0);
3089 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3090
3091 if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3092 rc = -EFAULT;
3093 return rc;
3094}
3095
3096static int modem_input_wait(struct slgt_info *info,int arg)
3097{
3098 unsigned long flags;
3099 int rc;
3100 struct mgsl_icount cprev, cnow;
3101 DECLARE_WAITQUEUE(wait, current);
3102
3103 /* save current irq counts */
3104 spin_lock_irqsave(&info->lock,flags);
3105 cprev = info->icount;
3106 add_wait_queue(&info->status_event_wait_q, &wait);
3107 set_current_state(TASK_INTERRUPTIBLE);
3108 spin_unlock_irqrestore(&info->lock,flags);
3109
3110 for(;;) {
3111 schedule();
3112 if (signal_pending(current)) {
3113 rc = -ERESTARTSYS;
3114 break;
3115 }
3116
3117 /* get new irq counts */
3118 spin_lock_irqsave(&info->lock,flags);
3119 cnow = info->icount;
3120 set_current_state(TASK_INTERRUPTIBLE);
3121 spin_unlock_irqrestore(&info->lock,flags);
3122
3123 /* if no change, wait aborted for some reason */
3124 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3125 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3126 rc = -EIO;
3127 break;
3128 }
3129
3130 /* check for change in caller specified modem input */
3131 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3132 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3133 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) ||
3134 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3135 rc = 0;
3136 break;
3137 }
3138
3139 cprev = cnow;
3140 }
3141 remove_wait_queue(&info->status_event_wait_q, &wait);
3142 set_current_state(TASK_RUNNING);
3143 return rc;
3144}
3145
3146/*
3147 * return state of serial control and status signals
3148 */
3149static int tiocmget(struct tty_struct *tty)
3150{
3151 struct slgt_info *info = tty->driver_data;
3152 unsigned int result;
3153 unsigned long flags;
3154
3155 spin_lock_irqsave(&info->lock,flags);
3156 get_signals(info);
3157 spin_unlock_irqrestore(&info->lock,flags);
3158
3159 result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3160 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3161 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3162 ((info->signals & SerialSignal_RI) ? TIOCM_RNG:0) +
3163 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3164 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3165
3166 DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3167 return result;
3168}
3169
3170/*
3171 * set modem control signals (DTR/RTS)
3172 *
3173 * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3174 * TIOCMSET = set/clear signal values
3175 * value bit mask for command
3176 */
3177static int tiocmset(struct tty_struct *tty,
3178 unsigned int set, unsigned int clear)
3179{
3180 struct slgt_info *info = tty->driver_data;
3181 unsigned long flags;
3182
3183 DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3184
3185 if (set & TIOCM_RTS)
3186 info->signals |= SerialSignal_RTS;
3187 if (set & TIOCM_DTR)
3188 info->signals |= SerialSignal_DTR;
3189 if (clear & TIOCM_RTS)
3190 info->signals &= ~SerialSignal_RTS;
3191 if (clear & TIOCM_DTR)
3192 info->signals &= ~SerialSignal_DTR;
3193
3194 spin_lock_irqsave(&info->lock,flags);
3195 set_signals(info);
3196 spin_unlock_irqrestore(&info->lock,flags);
3197 return 0;
3198}
3199
3200static int carrier_raised(struct tty_port *port)
3201{
3202 unsigned long flags;
3203 struct slgt_info *info = container_of(port, struct slgt_info, port);
3204
3205 spin_lock_irqsave(&info->lock,flags);
3206 get_signals(info);
3207 spin_unlock_irqrestore(&info->lock,flags);
3208 return (info->signals & SerialSignal_DCD) ? 1 : 0;
3209}
3210
3211static void dtr_rts(struct tty_port *port, int on)
3212{
3213 unsigned long flags;
3214 struct slgt_info *info = container_of(port, struct slgt_info, port);
3215
3216 spin_lock_irqsave(&info->lock,flags);
3217 if (on)
3218 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
3219 else
3220 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3221 set_signals(info);
3222 spin_unlock_irqrestore(&info->lock,flags);
3223}
3224
3225
3226/*
3227 * block current process until the device is ready to open
3228 */
3229static int block_til_ready(struct tty_struct *tty, struct file *filp,
3230 struct slgt_info *info)
3231{
3232 DECLARE_WAITQUEUE(wait, current);
3233 int retval;
3234 bool do_clocal = false;
3235 unsigned long flags;
3236 int cd;
3237 struct tty_port *port = &info->port;
3238
3239 DBGINFO(("%s block_til_ready\n", tty->driver->name));
3240
3241 if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
3242 /* nonblock mode is set or port is not enabled */
3243 tty_port_set_active(port, 1);
3244 return 0;
3245 }
3246
3247 if (C_CLOCAL(tty))
3248 do_clocal = true;
3249
3250 /* Wait for carrier detect and the line to become
3251 * free (i.e., not in use by the callout). While we are in
3252 * this loop, port->count is dropped by one, so that
3253 * close() knows when to free things. We restore it upon
3254 * exit, either normal or abnormal.
3255 */
3256
3257 retval = 0;
3258 add_wait_queue(&port->open_wait, &wait);
3259
3260 spin_lock_irqsave(&info->lock, flags);
3261 port->count--;
3262 spin_unlock_irqrestore(&info->lock, flags);
3263 port->blocked_open++;
3264
3265 while (1) {
3266 if (C_BAUD(tty) && tty_port_initialized(port))
3267 tty_port_raise_dtr_rts(port);
3268
3269 set_current_state(TASK_INTERRUPTIBLE);
3270
3271 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
3272 retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3273 -EAGAIN : -ERESTARTSYS;
3274 break;
3275 }
3276
3277 cd = tty_port_carrier_raised(port);
3278 if (do_clocal || cd)
3279 break;
3280
3281 if (signal_pending(current)) {
3282 retval = -ERESTARTSYS;
3283 break;
3284 }
3285
3286 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3287 tty_unlock(tty);
3288 schedule();
3289 tty_lock(tty);
3290 }
3291
3292 set_current_state(TASK_RUNNING);
3293 remove_wait_queue(&port->open_wait, &wait);
3294
3295 if (!tty_hung_up_p(filp))
3296 port->count++;
3297 port->blocked_open--;
3298
3299 if (!retval)
3300 tty_port_set_active(port, 1);
3301
3302 DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3303 return retval;
3304}
3305
3306/*
3307 * allocate buffers used for calling line discipline receive_buf
3308 * directly in synchronous mode
3309 * note: add 5 bytes to max frame size to allow appending
3310 * 32-bit CRC and status byte when configured to do so
3311 */
3312static int alloc_tmp_rbuf(struct slgt_info *info)
3313{
3314 info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3315 if (info->tmp_rbuf == NULL)
3316 return -ENOMEM;
3317 /* unused flag buffer to satisfy receive_buf calling interface */
3318 info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL);
3319 if (!info->flag_buf) {
3320 kfree(info->tmp_rbuf);
3321 info->tmp_rbuf = NULL;
3322 return -ENOMEM;
3323 }
3324 return 0;
3325}
3326
3327static void free_tmp_rbuf(struct slgt_info *info)
3328{
3329 kfree(info->tmp_rbuf);
3330 info->tmp_rbuf = NULL;
3331 kfree(info->flag_buf);
3332 info->flag_buf = NULL;
3333}
3334
3335/*
3336 * allocate DMA descriptor lists.
3337 */
3338static int alloc_desc(struct slgt_info *info)
3339{
3340 unsigned int i;
3341 unsigned int pbufs;
3342
3343 /* allocate memory to hold descriptor lists */
3344 info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE,
3345 &info->bufs_dma_addr);
3346 if (info->bufs == NULL)
3347 return -ENOMEM;
3348
3349 info->rbufs = (struct slgt_desc*)info->bufs;
3350 info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3351
3352 pbufs = (unsigned int)info->bufs_dma_addr;
3353
3354 /*
3355 * Build circular lists of descriptors
3356 */
3357
3358 for (i=0; i < info->rbuf_count; i++) {
3359 /* physical address of this descriptor */
3360 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3361
3362 /* physical address of next descriptor */
3363 if (i == info->rbuf_count - 1)
3364 info->rbufs[i].next = cpu_to_le32(pbufs);
3365 else
3366 info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3367 set_desc_count(info->rbufs[i], DMABUFSIZE);
3368 }
3369
3370 for (i=0; i < info->tbuf_count; i++) {
3371 /* physical address of this descriptor */
3372 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3373
3374 /* physical address of next descriptor */
3375 if (i == info->tbuf_count - 1)
3376 info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3377 else
3378 info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3379 }
3380
3381 return 0;
3382}
3383
3384static void free_desc(struct slgt_info *info)
3385{
3386 if (info->bufs != NULL) {
3387 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3388 info->bufs = NULL;
3389 info->rbufs = NULL;
3390 info->tbufs = NULL;
3391 }
3392}
3393
3394static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3395{
3396 int i;
3397 for (i=0; i < count; i++) {
3398 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3399 return -ENOMEM;
3400 bufs[i].pbuf = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3401 }
3402 return 0;
3403}
3404
3405static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3406{
3407 int i;
3408 for (i=0; i < count; i++) {
3409 if (bufs[i].buf == NULL)
3410 continue;
3411 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3412 bufs[i].buf = NULL;
3413 }
3414}
3415
3416static int alloc_dma_bufs(struct slgt_info *info)
3417{
3418 info->rbuf_count = 32;
3419 info->tbuf_count = 32;
3420
3421 if (alloc_desc(info) < 0 ||
3422 alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3423 alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3424 alloc_tmp_rbuf(info) < 0) {
3425 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3426 return -ENOMEM;
3427 }
3428 reset_rbufs(info);
3429 return 0;
3430}
3431
3432static void free_dma_bufs(struct slgt_info *info)
3433{
3434 if (info->bufs) {
3435 free_bufs(info, info->rbufs, info->rbuf_count);
3436 free_bufs(info, info->tbufs, info->tbuf_count);
3437 free_desc(info);
3438 }
3439 free_tmp_rbuf(info);
3440}
3441
3442static int claim_resources(struct slgt_info *info)
3443{
3444 if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3445 DBGERR(("%s reg addr conflict, addr=%08X\n",
3446 info->device_name, info->phys_reg_addr));
3447 info->init_error = DiagStatus_AddressConflict;
3448 goto errout;
3449 }
3450 else
3451 info->reg_addr_requested = true;
3452
3453 info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
3454 if (!info->reg_addr) {
3455 DBGERR(("%s can't map device registers, addr=%08X\n",
3456 info->device_name, info->phys_reg_addr));
3457 info->init_error = DiagStatus_CantAssignPciResources;
3458 goto errout;
3459 }
3460 return 0;
3461
3462errout:
3463 release_resources(info);
3464 return -ENODEV;
3465}
3466
3467static void release_resources(struct slgt_info *info)
3468{
3469 if (info->irq_requested) {
3470 free_irq(info->irq_level, info);
3471 info->irq_requested = false;
3472 }
3473
3474 if (info->reg_addr_requested) {
3475 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3476 info->reg_addr_requested = false;
3477 }
3478
3479 if (info->reg_addr) {
3480 iounmap(info->reg_addr);
3481 info->reg_addr = NULL;
3482 }
3483}
3484
3485/* Add the specified device instance data structure to the
3486 * global linked list of devices and increment the device count.
3487 */
3488static void add_device(struct slgt_info *info)
3489{
3490 char *devstr;
3491
3492 info->next_device = NULL;
3493 info->line = slgt_device_count;
3494 sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3495
3496 if (info->line < MAX_DEVICES) {
3497 if (maxframe[info->line])
3498 info->max_frame_size = maxframe[info->line];
3499 }
3500
3501 slgt_device_count++;
3502
3503 if (!slgt_device_list)
3504 slgt_device_list = info;
3505 else {
3506 struct slgt_info *current_dev = slgt_device_list;
3507 while(current_dev->next_device)
3508 current_dev = current_dev->next_device;
3509 current_dev->next_device = info;
3510 }
3511
3512 if (info->max_frame_size < 4096)
3513 info->max_frame_size = 4096;
3514 else if (info->max_frame_size > 65535)
3515 info->max_frame_size = 65535;
3516
3517 switch(info->pdev->device) {
3518 case SYNCLINK_GT_DEVICE_ID:
3519 devstr = "GT";
3520 break;
3521 case SYNCLINK_GT2_DEVICE_ID:
3522 devstr = "GT2";
3523 break;
3524 case SYNCLINK_GT4_DEVICE_ID:
3525 devstr = "GT4";
3526 break;
3527 case SYNCLINK_AC_DEVICE_ID:
3528 devstr = "AC";
3529 info->params.mode = MGSL_MODE_ASYNC;
3530 break;
3531 default:
3532 devstr = "(unknown model)";
3533 }
3534 printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3535 devstr, info->device_name, info->phys_reg_addr,
3536 info->irq_level, info->max_frame_size);
3537
3538#if SYNCLINK_GENERIC_HDLC
3539 hdlcdev_init(info);
3540#endif
3541}
3542
3543static const struct tty_port_operations slgt_port_ops = {
3544 .carrier_raised = carrier_raised,
3545 .dtr_rts = dtr_rts,
3546};
3547
3548/*
3549 * allocate device instance structure, return NULL on failure
3550 */
3551static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3552{
3553 struct slgt_info *info;
3554
3555 info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3556
3557 if (!info) {
3558 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3559 driver_name, adapter_num, port_num));
3560 } else {
3561 tty_port_init(&info->port);
3562 info->port.ops = &slgt_port_ops;
3563 info->magic = MGSL_MAGIC;
3564 INIT_WORK(&info->task, bh_handler);
3565 info->max_frame_size = 4096;
3566 info->base_clock = 14745600;
3567 info->rbuf_fill_level = DMABUFSIZE;
3568 info->port.close_delay = 5*HZ/10;
3569 info->port.closing_wait = 30*HZ;
3570 init_waitqueue_head(&info->status_event_wait_q);
3571 init_waitqueue_head(&info->event_wait_q);
3572 spin_lock_init(&info->netlock);
3573 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3574 info->idle_mode = HDLC_TXIDLE_FLAGS;
3575 info->adapter_num = adapter_num;
3576 info->port_num = port_num;
3577
3578 timer_setup(&info->tx_timer, tx_timeout, 0);
3579 timer_setup(&info->rx_timer, rx_timeout, 0);
3580
3581 /* Copy configuration info to device instance data */
3582 info->pdev = pdev;
3583 info->irq_level = pdev->irq;
3584 info->phys_reg_addr = pci_resource_start(pdev,0);
3585
3586 info->bus_type = MGSL_BUS_TYPE_PCI;
3587 info->irq_flags = IRQF_SHARED;
3588
3589 info->init_error = -1; /* assume error, set to 0 on successful init */
3590 }
3591
3592 return info;
3593}
3594
3595static void device_init(int adapter_num, struct pci_dev *pdev)
3596{
3597 struct slgt_info *port_array[SLGT_MAX_PORTS];
3598 int i;
3599 int port_count = 1;
3600
3601 if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3602 port_count = 2;
3603 else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3604 port_count = 4;
3605
3606 /* allocate device instances for all ports */
3607 for (i=0; i < port_count; ++i) {
3608 port_array[i] = alloc_dev(adapter_num, i, pdev);
3609 if (port_array[i] == NULL) {
3610 for (--i; i >= 0; --i) {
3611 tty_port_destroy(&port_array[i]->port);
3612 kfree(port_array[i]);
3613 }
3614 return;
3615 }
3616 }
3617
3618 /* give copy of port_array to all ports and add to device list */
3619 for (i=0; i < port_count; ++i) {
3620 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3621 add_device(port_array[i]);
3622 port_array[i]->port_count = port_count;
3623 spin_lock_init(&port_array[i]->lock);
3624 }
3625
3626 /* Allocate and claim adapter resources */
3627 if (!claim_resources(port_array[0])) {
3628
3629 alloc_dma_bufs(port_array[0]);
3630
3631 /* copy resource information from first port to others */
3632 for (i = 1; i < port_count; ++i) {
3633 port_array[i]->irq_level = port_array[0]->irq_level;
3634 port_array[i]->reg_addr = port_array[0]->reg_addr;
3635 alloc_dma_bufs(port_array[i]);
3636 }
3637
3638 if (request_irq(port_array[0]->irq_level,
3639 slgt_interrupt,
3640 port_array[0]->irq_flags,
3641 port_array[0]->device_name,
3642 port_array[0]) < 0) {
3643 DBGERR(("%s request_irq failed IRQ=%d\n",
3644 port_array[0]->device_name,
3645 port_array[0]->irq_level));
3646 } else {
3647 port_array[0]->irq_requested = true;
3648 adapter_test(port_array[0]);
3649 for (i=1 ; i < port_count ; i++) {
3650 port_array[i]->init_error = port_array[0]->init_error;
3651 port_array[i]->gpio_present = port_array[0]->gpio_present;
3652 }
3653 }
3654 }
3655
3656 for (i = 0; i < port_count; ++i) {
3657 struct slgt_info *info = port_array[i];
3658 tty_port_register_device(&info->port, serial_driver, info->line,
3659 &info->pdev->dev);
3660 }
3661}
3662
3663static int init_one(struct pci_dev *dev,
3664 const struct pci_device_id *ent)
3665{
3666 if (pci_enable_device(dev)) {
3667 printk("error enabling pci device %p\n", dev);
3668 return -EIO;
3669 }
3670 pci_set_master(dev);
3671 device_init(slgt_device_count, dev);
3672 return 0;
3673}
3674
3675static void remove_one(struct pci_dev *dev)
3676{
3677}
3678
3679static const struct tty_operations ops = {
3680 .open = open,
3681 .close = close,
3682 .write = write,
3683 .put_char = put_char,
3684 .flush_chars = flush_chars,
3685 .write_room = write_room,
3686 .chars_in_buffer = chars_in_buffer,
3687 .flush_buffer = flush_buffer,
3688 .ioctl = ioctl,
3689 .compat_ioctl = slgt_compat_ioctl,
3690 .throttle = throttle,
3691 .unthrottle = unthrottle,
3692 .send_xchar = send_xchar,
3693 .break_ctl = set_break,
3694 .wait_until_sent = wait_until_sent,
3695 .set_termios = set_termios,
3696 .stop = tx_hold,
3697 .start = tx_release,
3698 .hangup = hangup,
3699 .tiocmget = tiocmget,
3700 .tiocmset = tiocmset,
3701 .get_icount = get_icount,
3702 .proc_show = synclink_gt_proc_show,
3703};
3704
3705static void slgt_cleanup(void)
3706{
3707 int rc;
3708 struct slgt_info *info;
3709 struct slgt_info *tmp;
3710
3711 printk(KERN_INFO "unload %s\n", driver_name);
3712
3713 if (serial_driver) {
3714 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3715 tty_unregister_device(serial_driver, info->line);
3716 rc = tty_unregister_driver(serial_driver);
3717 if (rc)
3718 DBGERR(("tty_unregister_driver error=%d\n", rc));
3719 put_tty_driver(serial_driver);
3720 }
3721
3722 /* reset devices */
3723 info = slgt_device_list;
3724 while(info) {
3725 reset_port(info);
3726 info = info->next_device;
3727 }
3728
3729 /* release devices */
3730 info = slgt_device_list;
3731 while(info) {
3732#if SYNCLINK_GENERIC_HDLC
3733 hdlcdev_exit(info);
3734#endif
3735 free_dma_bufs(info);
3736 free_tmp_rbuf(info);
3737 if (info->port_num == 0)
3738 release_resources(info);
3739 tmp = info;
3740 info = info->next_device;
3741 tty_port_destroy(&tmp->port);
3742 kfree(tmp);
3743 }
3744
3745 if (pci_registered)
3746 pci_unregister_driver(&pci_driver);
3747}
3748
3749/*
3750 * Driver initialization entry point.
3751 */
3752static int __init slgt_init(void)
3753{
3754 int rc;
3755
3756 printk(KERN_INFO "%s\n", driver_name);
3757
3758 serial_driver = alloc_tty_driver(MAX_DEVICES);
3759 if (!serial_driver) {
3760 printk("%s can't allocate tty driver\n", driver_name);
3761 return -ENOMEM;
3762 }
3763
3764 /* Initialize the tty_driver structure */
3765
3766 serial_driver->driver_name = slgt_driver_name;
3767 serial_driver->name = tty_dev_prefix;
3768 serial_driver->major = ttymajor;
3769 serial_driver->minor_start = 64;
3770 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3771 serial_driver->subtype = SERIAL_TYPE_NORMAL;
3772 serial_driver->init_termios = tty_std_termios;
3773 serial_driver->init_termios.c_cflag =
3774 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3775 serial_driver->init_termios.c_ispeed = 9600;
3776 serial_driver->init_termios.c_ospeed = 9600;
3777 serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3778 tty_set_operations(serial_driver, &ops);
3779 if ((rc = tty_register_driver(serial_driver)) < 0) {
3780 DBGERR(("%s can't register serial driver\n", driver_name));
3781 put_tty_driver(serial_driver);
3782 serial_driver = NULL;
3783 goto error;
3784 }
3785
3786 printk(KERN_INFO "%s, tty major#%d\n",
3787 driver_name, serial_driver->major);
3788
3789 slgt_device_count = 0;
3790 if ((rc = pci_register_driver(&pci_driver)) < 0) {
3791 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3792 goto error;
3793 }
3794 pci_registered = true;
3795
3796 if (!slgt_device_list)
3797 printk("%s no devices found\n",driver_name);
3798
3799 return 0;
3800
3801error:
3802 slgt_cleanup();
3803 return rc;
3804}
3805
3806static void __exit slgt_exit(void)
3807{
3808 slgt_cleanup();
3809}
3810
3811module_init(slgt_init);
3812module_exit(slgt_exit);
3813
3814/*
3815 * register access routines
3816 */
3817
3818#define CALC_REGADDR() \
3819 unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3820 if (addr >= 0x80) \
3821 reg_addr += (info->port_num) * 32; \
3822 else if (addr >= 0x40) \
3823 reg_addr += (info->port_num) * 16;
3824
3825static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3826{
3827 CALC_REGADDR();
3828 return readb((void __iomem *)reg_addr);
3829}
3830
3831static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3832{
3833 CALC_REGADDR();
3834 writeb(value, (void __iomem *)reg_addr);
3835}
3836
3837static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3838{
3839 CALC_REGADDR();
3840 return readw((void __iomem *)reg_addr);
3841}
3842
3843static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3844{
3845 CALC_REGADDR();
3846 writew(value, (void __iomem *)reg_addr);
3847}
3848
3849static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3850{
3851 CALC_REGADDR();
3852 return readl((void __iomem *)reg_addr);
3853}
3854
3855static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3856{
3857 CALC_REGADDR();
3858 writel(value, (void __iomem *)reg_addr);
3859}
3860
3861static void rdma_reset(struct slgt_info *info)
3862{
3863 unsigned int i;
3864
3865 /* set reset bit */
3866 wr_reg32(info, RDCSR, BIT1);
3867
3868 /* wait for enable bit cleared */
3869 for(i=0 ; i < 1000 ; i++)
3870 if (!(rd_reg32(info, RDCSR) & BIT0))
3871 break;
3872}
3873
3874static void tdma_reset(struct slgt_info *info)
3875{
3876 unsigned int i;
3877
3878 /* set reset bit */
3879 wr_reg32(info, TDCSR, BIT1);
3880
3881 /* wait for enable bit cleared */
3882 for(i=0 ; i < 1000 ; i++)
3883 if (!(rd_reg32(info, TDCSR) & BIT0))
3884 break;
3885}
3886
3887/*
3888 * enable internal loopback
3889 * TxCLK and RxCLK are generated from BRG
3890 * and TxD is looped back to RxD internally.
3891 */
3892static void enable_loopback(struct slgt_info *info)
3893{
3894 /* SCR (serial control) BIT2=loopback enable */
3895 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3896
3897 if (info->params.mode != MGSL_MODE_ASYNC) {
3898 /* CCR (clock control)
3899 * 07..05 tx clock source (010 = BRG)
3900 * 04..02 rx clock source (010 = BRG)
3901 * 01 auxclk enable (0 = disable)
3902 * 00 BRG enable (1 = enable)
3903 *
3904 * 0100 1001
3905 */
3906 wr_reg8(info, CCR, 0x49);
3907
3908 /* set speed if available, otherwise use default */
3909 if (info->params.clock_speed)
3910 set_rate(info, info->params.clock_speed);
3911 else
3912 set_rate(info, 3686400);
3913 }
3914}
3915
3916/*
3917 * set baud rate generator to specified rate
3918 */
3919static void set_rate(struct slgt_info *info, u32 rate)
3920{
3921 unsigned int div;
3922 unsigned int osc = info->base_clock;
3923
3924 /* div = osc/rate - 1
3925 *
3926 * Round div up if osc/rate is not integer to
3927 * force to next slowest rate.
3928 */
3929
3930 if (rate) {
3931 div = osc/rate;
3932 if (!(osc % rate) && div)
3933 div--;
3934 wr_reg16(info, BDR, (unsigned short)div);
3935 }
3936}
3937
3938static void rx_stop(struct slgt_info *info)
3939{
3940 unsigned short val;
3941
3942 /* disable and reset receiver */
3943 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3944 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3945 wr_reg16(info, RCR, val); /* clear reset bit */
3946
3947 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3948
3949 /* clear pending rx interrupts */
3950 wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3951
3952 rdma_reset(info);
3953
3954 info->rx_enabled = false;
3955 info->rx_restart = false;
3956}
3957
3958static void rx_start(struct slgt_info *info)
3959{
3960 unsigned short val;
3961
3962 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3963
3964 /* clear pending rx overrun IRQ */
3965 wr_reg16(info, SSR, IRQ_RXOVER);
3966
3967 /* reset and disable receiver */
3968 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3969 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3970 wr_reg16(info, RCR, val); /* clear reset bit */
3971
3972 rdma_reset(info);
3973 reset_rbufs(info);
3974
3975 if (info->rx_pio) {
3976 /* rx request when rx FIFO not empty */
3977 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
3978 slgt_irq_on(info, IRQ_RXDATA);
3979 if (info->params.mode == MGSL_MODE_ASYNC) {
3980 /* enable saving of rx status */
3981 wr_reg32(info, RDCSR, BIT6);
3982 }
3983 } else {
3984 /* rx request when rx FIFO half full */
3985 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
3986 /* set 1st descriptor address */
3987 wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3988
3989 if (info->params.mode != MGSL_MODE_ASYNC) {
3990 /* enable rx DMA and DMA interrupt */
3991 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3992 } else {
3993 /* enable saving of rx status, rx DMA and DMA interrupt */
3994 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3995 }
3996 }
3997
3998 slgt_irq_on(info, IRQ_RXOVER);
3999
4000 /* enable receiver */
4001 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
4002
4003 info->rx_restart = false;
4004 info->rx_enabled = true;
4005}
4006
4007static void tx_start(struct slgt_info *info)
4008{
4009 if (!info->tx_enabled) {
4010 wr_reg16(info, TCR,
4011 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
4012 info->tx_enabled = true;
4013 }
4014
4015 if (desc_count(info->tbufs[info->tbuf_start])) {
4016 info->drop_rts_on_tx_done = false;
4017
4018 if (info->params.mode != MGSL_MODE_ASYNC) {
4019 if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
4020 get_signals(info);
4021 if (!(info->signals & SerialSignal_RTS)) {
4022 info->signals |= SerialSignal_RTS;
4023 set_signals(info);
4024 info->drop_rts_on_tx_done = true;
4025 }
4026 }
4027
4028 slgt_irq_off(info, IRQ_TXDATA);
4029 slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
4030 /* clear tx idle and underrun status bits */
4031 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4032 } else {
4033 slgt_irq_off(info, IRQ_TXDATA);
4034 slgt_irq_on(info, IRQ_TXIDLE);
4035 /* clear tx idle status bit */
4036 wr_reg16(info, SSR, IRQ_TXIDLE);
4037 }
4038 /* set 1st descriptor address and start DMA */
4039 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
4040 wr_reg32(info, TDCSR, BIT2 + BIT0);
4041 info->tx_active = true;
4042 }
4043}
4044
4045static void tx_stop(struct slgt_info *info)
4046{
4047 unsigned short val;
4048
4049 del_timer(&info->tx_timer);
4050
4051 tdma_reset(info);
4052
4053 /* reset and disable transmitter */
4054 val = rd_reg16(info, TCR) & ~BIT1; /* clear enable bit */
4055 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
4056
4057 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
4058
4059 /* clear tx idle and underrun status bit */
4060 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4061
4062 reset_tbufs(info);
4063
4064 info->tx_enabled = false;
4065 info->tx_active = false;
4066}
4067
4068static void reset_port(struct slgt_info *info)
4069{
4070 if (!info->reg_addr)
4071 return;
4072
4073 tx_stop(info);
4074 rx_stop(info);
4075
4076 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
4077 set_signals(info);
4078
4079 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4080}
4081
4082static void reset_adapter(struct slgt_info *info)
4083{
4084 int i;
4085 for (i=0; i < info->port_count; ++i) {
4086 if (info->port_array[i])
4087 reset_port(info->port_array[i]);
4088 }
4089}
4090
4091static void async_mode(struct slgt_info *info)
4092{
4093 unsigned short val;
4094
4095 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4096 tx_stop(info);
4097 rx_stop(info);
4098
4099 /* TCR (tx control)
4100 *
4101 * 15..13 mode, 010=async
4102 * 12..10 encoding, 000=NRZ
4103 * 09 parity enable
4104 * 08 1=odd parity, 0=even parity
4105 * 07 1=RTS driver control
4106 * 06 1=break enable
4107 * 05..04 character length
4108 * 00=5 bits
4109 * 01=6 bits
4110 * 10=7 bits
4111 * 11=8 bits
4112 * 03 0=1 stop bit, 1=2 stop bits
4113 * 02 reset
4114 * 01 enable
4115 * 00 auto-CTS enable
4116 */
4117 val = 0x4000;
4118
4119 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4120 val |= BIT7;
4121
4122 if (info->params.parity != ASYNC_PARITY_NONE) {
4123 val |= BIT9;
4124 if (info->params.parity == ASYNC_PARITY_ODD)
4125 val |= BIT8;
4126 }
4127
4128 switch (info->params.data_bits)
4129 {
4130 case 6: val |= BIT4; break;
4131 case 7: val |= BIT5; break;
4132 case 8: val |= BIT5 + BIT4; break;
4133 }
4134
4135 if (info->params.stop_bits != 1)
4136 val |= BIT3;
4137
4138 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4139 val |= BIT0;
4140
4141 wr_reg16(info, TCR, val);
4142
4143 /* RCR (rx control)
4144 *
4145 * 15..13 mode, 010=async
4146 * 12..10 encoding, 000=NRZ
4147 * 09 parity enable
4148 * 08 1=odd parity, 0=even parity
4149 * 07..06 reserved, must be 0
4150 * 05..04 character length
4151 * 00=5 bits
4152 * 01=6 bits
4153 * 10=7 bits
4154 * 11=8 bits
4155 * 03 reserved, must be zero
4156 * 02 reset
4157 * 01 enable
4158 * 00 auto-DCD enable
4159 */
4160 val = 0x4000;
4161
4162 if (info->params.parity != ASYNC_PARITY_NONE) {
4163 val |= BIT9;
4164 if (info->params.parity == ASYNC_PARITY_ODD)
4165 val |= BIT8;
4166 }
4167
4168 switch (info->params.data_bits)
4169 {
4170 case 6: val |= BIT4; break;
4171 case 7: val |= BIT5; break;
4172 case 8: val |= BIT5 + BIT4; break;
4173 }
4174
4175 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4176 val |= BIT0;
4177
4178 wr_reg16(info, RCR, val);
4179
4180 /* CCR (clock control)
4181 *
4182 * 07..05 011 = tx clock source is BRG/16
4183 * 04..02 010 = rx clock source is BRG
4184 * 01 0 = auxclk disabled
4185 * 00 1 = BRG enabled
4186 *
4187 * 0110 1001
4188 */
4189 wr_reg8(info, CCR, 0x69);
4190
4191 msc_set_vcr(info);
4192
4193 /* SCR (serial control)
4194 *
4195 * 15 1=tx req on FIFO half empty
4196 * 14 1=rx req on FIFO half full
4197 * 13 tx data IRQ enable
4198 * 12 tx idle IRQ enable
4199 * 11 rx break on IRQ enable
4200 * 10 rx data IRQ enable
4201 * 09 rx break off IRQ enable
4202 * 08 overrun IRQ enable
4203 * 07 DSR IRQ enable
4204 * 06 CTS IRQ enable
4205 * 05 DCD IRQ enable
4206 * 04 RI IRQ enable
4207 * 03 0=16x sampling, 1=8x sampling
4208 * 02 1=txd->rxd internal loopback enable
4209 * 01 reserved, must be zero
4210 * 00 1=master IRQ enable
4211 */
4212 val = BIT15 + BIT14 + BIT0;
4213 /* JCR[8] : 1 = x8 async mode feature available */
4214 if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4215 ((info->base_clock < (info->params.data_rate * 16)) ||
4216 (info->base_clock % (info->params.data_rate * 16)))) {
4217 /* use 8x sampling */
4218 val |= BIT3;
4219 set_rate(info, info->params.data_rate * 8);
4220 } else {
4221 /* use 16x sampling */
4222 set_rate(info, info->params.data_rate * 16);
4223 }
4224 wr_reg16(info, SCR, val);
4225
4226 slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4227
4228 if (info->params.loopback)
4229 enable_loopback(info);
4230}
4231
4232static void sync_mode(struct slgt_info *info)
4233{
4234 unsigned short val;
4235
4236 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4237 tx_stop(info);
4238 rx_stop(info);
4239
4240 /* TCR (tx control)
4241 *
4242 * 15..13 mode
4243 * 000=HDLC/SDLC
4244 * 001=raw bit synchronous
4245 * 010=asynchronous/isochronous
4246 * 011=monosync byte synchronous
4247 * 100=bisync byte synchronous
4248 * 101=xsync byte synchronous
4249 * 12..10 encoding
4250 * 09 CRC enable
4251 * 08 CRC32
4252 * 07 1=RTS driver control
4253 * 06 preamble enable
4254 * 05..04 preamble length
4255 * 03 share open/close flag
4256 * 02 reset
4257 * 01 enable
4258 * 00 auto-CTS enable
4259 */
4260 val = BIT2;
4261
4262 switch(info->params.mode) {
4263 case MGSL_MODE_XSYNC:
4264 val |= BIT15 + BIT13;
4265 break;
4266 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4267 case MGSL_MODE_BISYNC: val |= BIT15; break;
4268 case MGSL_MODE_RAW: val |= BIT13; break;
4269 }
4270 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4271 val |= BIT7;
4272
4273 switch(info->params.encoding)
4274 {
4275 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4276 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4277 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4278 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4279 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4280 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4281 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4282 }
4283
4284 switch (info->params.crc_type & HDLC_CRC_MASK)
4285 {
4286 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4287 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4288 }
4289
4290 if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4291 val |= BIT6;
4292
4293 switch (info->params.preamble_length)
4294 {
4295 case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4296 case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4297 case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4298 }
4299
4300 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4301 val |= BIT0;
4302
4303 wr_reg16(info, TCR, val);
4304
4305 /* TPR (transmit preamble) */
4306
4307 switch (info->params.preamble)
4308 {
4309 case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4310 case HDLC_PREAMBLE_PATTERN_ONES: val = 0xff; break;
4311 case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4312 case HDLC_PREAMBLE_PATTERN_10: val = 0x55; break;
4313 case HDLC_PREAMBLE_PATTERN_01: val = 0xaa; break;
4314 default: val = 0x7e; break;
4315 }
4316 wr_reg8(info, TPR, (unsigned char)val);
4317
4318 /* RCR (rx control)
4319 *
4320 * 15..13 mode
4321 * 000=HDLC/SDLC
4322 * 001=raw bit synchronous
4323 * 010=asynchronous/isochronous
4324 * 011=monosync byte synchronous
4325 * 100=bisync byte synchronous
4326 * 101=xsync byte synchronous
4327 * 12..10 encoding
4328 * 09 CRC enable
4329 * 08 CRC32
4330 * 07..03 reserved, must be 0
4331 * 02 reset
4332 * 01 enable
4333 * 00 auto-DCD enable
4334 */
4335 val = 0;
4336
4337 switch(info->params.mode) {
4338 case MGSL_MODE_XSYNC:
4339 val |= BIT15 + BIT13;
4340 break;
4341 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4342 case MGSL_MODE_BISYNC: val |= BIT15; break;
4343 case MGSL_MODE_RAW: val |= BIT13; break;
4344 }
4345
4346 switch(info->params.encoding)
4347 {
4348 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4349 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4350 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4351 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4352 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4353 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4354 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4355 }
4356
4357 switch (info->params.crc_type & HDLC_CRC_MASK)
4358 {
4359 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4360 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4361 }
4362
4363 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4364 val |= BIT0;
4365
4366 wr_reg16(info, RCR, val);
4367
4368 /* CCR (clock control)
4369 *
4370 * 07..05 tx clock source
4371 * 04..02 rx clock source
4372 * 01 auxclk enable
4373 * 00 BRG enable
4374 */
4375 val = 0;
4376
4377 if (info->params.flags & HDLC_FLAG_TXC_BRG)
4378 {
4379 // when RxC source is DPLL, BRG generates 16X DPLL
4380 // reference clock, so take TxC from BRG/16 to get
4381 // transmit clock at actual data rate
4382 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4383 val |= BIT6 + BIT5; /* 011, txclk = BRG/16 */
4384 else
4385 val |= BIT6; /* 010, txclk = BRG */
4386 }
4387 else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4388 val |= BIT7; /* 100, txclk = DPLL Input */
4389 else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4390 val |= BIT5; /* 001, txclk = RXC Input */
4391
4392 if (info->params.flags & HDLC_FLAG_RXC_BRG)
4393 val |= BIT3; /* 010, rxclk = BRG */
4394 else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4395 val |= BIT4; /* 100, rxclk = DPLL */
4396 else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4397 val |= BIT2; /* 001, rxclk = TXC Input */
4398
4399 if (info->params.clock_speed)
4400 val |= BIT1 + BIT0;
4401
4402 wr_reg8(info, CCR, (unsigned char)val);
4403
4404 if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4405 {
4406 // program DPLL mode
4407 switch(info->params.encoding)
4408 {
4409 case HDLC_ENCODING_BIPHASE_MARK:
4410 case HDLC_ENCODING_BIPHASE_SPACE:
4411 val = BIT7; break;
4412 case HDLC_ENCODING_BIPHASE_LEVEL:
4413 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4414 val = BIT7 + BIT6; break;
4415 default: val = BIT6; // NRZ encodings
4416 }
4417 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4418
4419 // DPLL requires a 16X reference clock from BRG
4420 set_rate(info, info->params.clock_speed * 16);
4421 }
4422 else
4423 set_rate(info, info->params.clock_speed);
4424
4425 tx_set_idle(info);
4426
4427 msc_set_vcr(info);
4428
4429 /* SCR (serial control)
4430 *
4431 * 15 1=tx req on FIFO half empty
4432 * 14 1=rx req on FIFO half full
4433 * 13 tx data IRQ enable
4434 * 12 tx idle IRQ enable
4435 * 11 underrun IRQ enable
4436 * 10 rx data IRQ enable
4437 * 09 rx idle IRQ enable
4438 * 08 overrun IRQ enable
4439 * 07 DSR IRQ enable
4440 * 06 CTS IRQ enable
4441 * 05 DCD IRQ enable
4442 * 04 RI IRQ enable
4443 * 03 reserved, must be zero
4444 * 02 1=txd->rxd internal loopback enable
4445 * 01 reserved, must be zero
4446 * 00 1=master IRQ enable
4447 */
4448 wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4449
4450 if (info->params.loopback)
4451 enable_loopback(info);
4452}
4453
4454/*
4455 * set transmit idle mode
4456 */
4457static void tx_set_idle(struct slgt_info *info)
4458{
4459 unsigned char val;
4460 unsigned short tcr;
4461
4462 /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4463 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4464 */
4465 tcr = rd_reg16(info, TCR);
4466 if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4467 /* disable preamble, set idle size to 16 bits */
4468 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4469 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4470 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4471 } else if (!(tcr & BIT6)) {
4472 /* preamble is disabled, set idle size to 8 bits */
4473 tcr &= ~(BIT5 + BIT4);
4474 }
4475 wr_reg16(info, TCR, tcr);
4476
4477 if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4478 /* LSB of custom tx idle specified in tx idle register */
4479 val = (unsigned char)(info->idle_mode & 0xff);
4480 } else {
4481 /* standard 8 bit idle patterns */
4482 switch(info->idle_mode)
4483 {
4484 case HDLC_TXIDLE_FLAGS: val = 0x7e; break;
4485 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4486 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4487 case HDLC_TXIDLE_ZEROS:
4488 case HDLC_TXIDLE_SPACE: val = 0x00; break;
4489 default: val = 0xff;
4490 }
4491 }
4492
4493 wr_reg8(info, TIR, val);
4494}
4495
4496/*
4497 * get state of V24 status (input) signals
4498 */
4499static void get_signals(struct slgt_info *info)
4500{
4501 unsigned short status = rd_reg16(info, SSR);
4502
4503 /* clear all serial signals except RTS and DTR */
4504 info->signals &= SerialSignal_RTS | SerialSignal_DTR;
4505
4506 if (status & BIT3)
4507 info->signals |= SerialSignal_DSR;
4508 if (status & BIT2)
4509 info->signals |= SerialSignal_CTS;
4510 if (status & BIT1)
4511 info->signals |= SerialSignal_DCD;
4512 if (status & BIT0)
4513 info->signals |= SerialSignal_RI;
4514}
4515
4516/*
4517 * set V.24 Control Register based on current configuration
4518 */
4519static void msc_set_vcr(struct slgt_info *info)
4520{
4521 unsigned char val = 0;
4522
4523 /* VCR (V.24 control)
4524 *
4525 * 07..04 serial IF select
4526 * 03 DTR
4527 * 02 RTS
4528 * 01 LL
4529 * 00 RL
4530 */
4531
4532 switch(info->if_mode & MGSL_INTERFACE_MASK)
4533 {
4534 case MGSL_INTERFACE_RS232:
4535 val |= BIT5; /* 0010 */
4536 break;
4537 case MGSL_INTERFACE_V35:
4538 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4539 break;
4540 case MGSL_INTERFACE_RS422:
4541 val |= BIT6; /* 0100 */
4542 break;
4543 }
4544
4545 if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4546 val |= BIT4;
4547 if (info->signals & SerialSignal_DTR)
4548 val |= BIT3;
4549 if (info->signals & SerialSignal_RTS)
4550 val |= BIT2;
4551 if (info->if_mode & MGSL_INTERFACE_LL)
4552 val |= BIT1;
4553 if (info->if_mode & MGSL_INTERFACE_RL)
4554 val |= BIT0;
4555 wr_reg8(info, VCR, val);
4556}
4557
4558/*
4559 * set state of V24 control (output) signals
4560 */
4561static void set_signals(struct slgt_info *info)
4562{
4563 unsigned char val = rd_reg8(info, VCR);
4564 if (info->signals & SerialSignal_DTR)
4565 val |= BIT3;
4566 else
4567 val &= ~BIT3;
4568 if (info->signals & SerialSignal_RTS)
4569 val |= BIT2;
4570 else
4571 val &= ~BIT2;
4572 wr_reg8(info, VCR, val);
4573}
4574
4575/*
4576 * free range of receive DMA buffers (i to last)
4577 */
4578static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4579{
4580 int done = 0;
4581
4582 while(!done) {
4583 /* reset current buffer for reuse */
4584 info->rbufs[i].status = 0;
4585 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4586 if (i == last)
4587 done = 1;
4588 if (++i == info->rbuf_count)
4589 i = 0;
4590 }
4591 info->rbuf_current = i;
4592}
4593
4594/*
4595 * mark all receive DMA buffers as free
4596 */
4597static void reset_rbufs(struct slgt_info *info)
4598{
4599 free_rbufs(info, 0, info->rbuf_count - 1);
4600 info->rbuf_fill_index = 0;
4601 info->rbuf_fill_count = 0;
4602}
4603
4604/*
4605 * pass receive HDLC frame to upper layer
4606 *
4607 * return true if frame available, otherwise false
4608 */
4609static bool rx_get_frame(struct slgt_info *info)
4610{
4611 unsigned int start, end;
4612 unsigned short status;
4613 unsigned int framesize = 0;
4614 unsigned long flags;
4615 struct tty_struct *tty = info->port.tty;
4616 unsigned char addr_field = 0xff;
4617 unsigned int crc_size = 0;
4618
4619 switch (info->params.crc_type & HDLC_CRC_MASK) {
4620 case HDLC_CRC_16_CCITT: crc_size = 2; break;
4621 case HDLC_CRC_32_CCITT: crc_size = 4; break;
4622 }
4623
4624check_again:
4625
4626 framesize = 0;
4627 addr_field = 0xff;
4628 start = end = info->rbuf_current;
4629
4630 for (;;) {
4631 if (!desc_complete(info->rbufs[end]))
4632 goto cleanup;
4633
4634 if (framesize == 0 && info->params.addr_filter != 0xff)
4635 addr_field = info->rbufs[end].buf[0];
4636
4637 framesize += desc_count(info->rbufs[end]);
4638
4639 if (desc_eof(info->rbufs[end]))
4640 break;
4641
4642 if (++end == info->rbuf_count)
4643 end = 0;
4644
4645 if (end == info->rbuf_current) {
4646 if (info->rx_enabled){
4647 spin_lock_irqsave(&info->lock,flags);
4648 rx_start(info);
4649 spin_unlock_irqrestore(&info->lock,flags);
4650 }
4651 goto cleanup;
4652 }
4653 }
4654
4655 /* status
4656 *
4657 * 15 buffer complete
4658 * 14..06 reserved
4659 * 05..04 residue
4660 * 02 eof (end of frame)
4661 * 01 CRC error
4662 * 00 abort
4663 */
4664 status = desc_status(info->rbufs[end]);
4665
4666 /* ignore CRC bit if not using CRC (bit is undefined) */
4667 if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4668 status &= ~BIT1;
4669
4670 if (framesize == 0 ||
4671 (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4672 free_rbufs(info, start, end);
4673 goto check_again;
4674 }
4675
4676 if (framesize < (2 + crc_size) || status & BIT0) {
4677 info->icount.rxshort++;
4678 framesize = 0;
4679 } else if (status & BIT1) {
4680 info->icount.rxcrc++;
4681 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4682 framesize = 0;
4683 }
4684
4685#if SYNCLINK_GENERIC_HDLC
4686 if (framesize == 0) {
4687 info->netdev->stats.rx_errors++;
4688 info->netdev->stats.rx_frame_errors++;
4689 }
4690#endif
4691
4692 DBGBH(("%s rx frame status=%04X size=%d\n",
4693 info->device_name, status, framesize));
4694 DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4695
4696 if (framesize) {
4697 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4698 framesize -= crc_size;
4699 crc_size = 0;
4700 }
4701
4702 if (framesize > info->max_frame_size + crc_size)
4703 info->icount.rxlong++;
4704 else {
4705 /* copy dma buffer(s) to contiguous temp buffer */
4706 int copy_count = framesize;
4707 int i = start;
4708 unsigned char *p = info->tmp_rbuf;
4709 info->tmp_rbuf_count = framesize;
4710
4711 info->icount.rxok++;
4712
4713 while(copy_count) {
4714 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4715 memcpy(p, info->rbufs[i].buf, partial_count);
4716 p += partial_count;
4717 copy_count -= partial_count;
4718 if (++i == info->rbuf_count)
4719 i = 0;
4720 }
4721
4722 if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4723 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4724 framesize++;
4725 }
4726
4727#if SYNCLINK_GENERIC_HDLC
4728 if (info->netcount)
4729 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4730 else
4731#endif
4732 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4733 }
4734 }
4735 free_rbufs(info, start, end);
4736 return true;
4737
4738cleanup:
4739 return false;
4740}
4741
4742/*
4743 * pass receive buffer (RAW synchronous mode) to tty layer
4744 * return true if buffer available, otherwise false
4745 */
4746static bool rx_get_buf(struct slgt_info *info)
4747{
4748 unsigned int i = info->rbuf_current;
4749 unsigned int count;
4750
4751 if (!desc_complete(info->rbufs[i]))
4752 return false;
4753 count = desc_count(info->rbufs[i]);
4754 switch(info->params.mode) {
4755 case MGSL_MODE_MONOSYNC:
4756 case MGSL_MODE_BISYNC:
4757 case MGSL_MODE_XSYNC:
4758 /* ignore residue in byte synchronous modes */
4759 if (desc_residue(info->rbufs[i]))
4760 count--;
4761 break;
4762 }
4763 DBGDATA(info, info->rbufs[i].buf, count, "rx");
4764 DBGINFO(("rx_get_buf size=%d\n", count));
4765 if (count)
4766 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4767 info->flag_buf, count);
4768 free_rbufs(info, i, i);
4769 return true;
4770}
4771
4772static void reset_tbufs(struct slgt_info *info)
4773{
4774 unsigned int i;
4775 info->tbuf_current = 0;
4776 for (i=0 ; i < info->tbuf_count ; i++) {
4777 info->tbufs[i].status = 0;
4778 info->tbufs[i].count = 0;
4779 }
4780}
4781
4782/*
4783 * return number of free transmit DMA buffers
4784 */
4785static unsigned int free_tbuf_count(struct slgt_info *info)
4786{
4787 unsigned int count = 0;
4788 unsigned int i = info->tbuf_current;
4789
4790 do
4791 {
4792 if (desc_count(info->tbufs[i]))
4793 break; /* buffer in use */
4794 ++count;
4795 if (++i == info->tbuf_count)
4796 i=0;
4797 } while (i != info->tbuf_current);
4798
4799 /* if tx DMA active, last zero count buffer is in use */
4800 if (count && (rd_reg32(info, TDCSR) & BIT0))
4801 --count;
4802
4803 return count;
4804}
4805
4806/*
4807 * return number of bytes in unsent transmit DMA buffers
4808 * and the serial controller tx FIFO
4809 */
4810static unsigned int tbuf_bytes(struct slgt_info *info)
4811{
4812 unsigned int total_count = 0;
4813 unsigned int i = info->tbuf_current;
4814 unsigned int reg_value;
4815 unsigned int count;
4816 unsigned int active_buf_count = 0;
4817
4818 /*
4819 * Add descriptor counts for all tx DMA buffers.
4820 * If count is zero (cleared by DMA controller after read),
4821 * the buffer is complete or is actively being read from.
4822 *
4823 * Record buf_count of last buffer with zero count starting
4824 * from current ring position. buf_count is mirror
4825 * copy of count and is not cleared by serial controller.
4826 * If DMA controller is active, that buffer is actively
4827 * being read so add to total.
4828 */
4829 do {
4830 count = desc_count(info->tbufs[i]);
4831 if (count)
4832 total_count += count;
4833 else if (!total_count)
4834 active_buf_count = info->tbufs[i].buf_count;
4835 if (++i == info->tbuf_count)
4836 i = 0;
4837 } while (i != info->tbuf_current);
4838
4839 /* read tx DMA status register */
4840 reg_value = rd_reg32(info, TDCSR);
4841
4842 /* if tx DMA active, last zero count buffer is in use */
4843 if (reg_value & BIT0)
4844 total_count += active_buf_count;
4845
4846 /* add tx FIFO count = reg_value[15..8] */
4847 total_count += (reg_value >> 8) & 0xff;
4848
4849 /* if transmitter active add one byte for shift register */
4850 if (info->tx_active)
4851 total_count++;
4852
4853 return total_count;
4854}
4855
4856/*
4857 * load data into transmit DMA buffer ring and start transmitter if needed
4858 * return true if data accepted, otherwise false (buffers full)
4859 */
4860static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4861{
4862 unsigned short count;
4863 unsigned int i;
4864 struct slgt_desc *d;
4865
4866 /* check required buffer space */
4867 if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4868 return false;
4869
4870 DBGDATA(info, buf, size, "tx");
4871
4872 /*
4873 * copy data to one or more DMA buffers in circular ring
4874 * tbuf_start = first buffer for this data
4875 * tbuf_current = next free buffer
4876 *
4877 * Copy all data before making data visible to DMA controller by
4878 * setting descriptor count of the first buffer.
4879 * This prevents an active DMA controller from reading the first DMA
4880 * buffers of a frame and stopping before the final buffers are filled.
4881 */
4882
4883 info->tbuf_start = i = info->tbuf_current;
4884
4885 while (size) {
4886 d = &info->tbufs[i];
4887
4888 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4889 memcpy(d->buf, buf, count);
4890
4891 size -= count;
4892 buf += count;
4893
4894 /*
4895 * set EOF bit for last buffer of HDLC frame or
4896 * for every buffer in raw mode
4897 */
4898 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4899 info->params.mode == MGSL_MODE_RAW)
4900 set_desc_eof(*d, 1);
4901 else
4902 set_desc_eof(*d, 0);
4903
4904 /* set descriptor count for all but first buffer */
4905 if (i != info->tbuf_start)
4906 set_desc_count(*d, count);
4907 d->buf_count = count;
4908
4909 if (++i == info->tbuf_count)
4910 i = 0;
4911 }
4912
4913 info->tbuf_current = i;
4914
4915 /* set first buffer count to make new data visible to DMA controller */
4916 d = &info->tbufs[info->tbuf_start];
4917 set_desc_count(*d, d->buf_count);
4918
4919 /* start transmitter if needed and update transmit timeout */
4920 if (!info->tx_active)
4921 tx_start(info);
4922 update_tx_timer(info);
4923
4924 return true;
4925}
4926
4927static int register_test(struct slgt_info *info)
4928{
4929 static unsigned short patterns[] =
4930 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4931 static unsigned int count = ARRAY_SIZE(patterns);
4932 unsigned int i;
4933 int rc = 0;
4934
4935 for (i=0 ; i < count ; i++) {
4936 wr_reg16(info, TIR, patterns[i]);
4937 wr_reg16(info, BDR, patterns[(i+1)%count]);
4938 if ((rd_reg16(info, TIR) != patterns[i]) ||
4939 (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4940 rc = -ENODEV;
4941 break;
4942 }
4943 }
4944 info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4945 info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4946 return rc;
4947}
4948
4949static int irq_test(struct slgt_info *info)
4950{
4951 unsigned long timeout;
4952 unsigned long flags;
4953 struct tty_struct *oldtty = info->port.tty;
4954 u32 speed = info->params.data_rate;
4955
4956 info->params.data_rate = 921600;
4957 info->port.tty = NULL;
4958
4959 spin_lock_irqsave(&info->lock, flags);
4960 async_mode(info);
4961 slgt_irq_on(info, IRQ_TXIDLE);
4962
4963 /* enable transmitter */
4964 wr_reg16(info, TCR,
4965 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4966
4967 /* write one byte and wait for tx idle */
4968 wr_reg16(info, TDR, 0);
4969
4970 /* assume failure */
4971 info->init_error = DiagStatus_IrqFailure;
4972 info->irq_occurred = false;
4973
4974 spin_unlock_irqrestore(&info->lock, flags);
4975
4976 timeout=100;
4977 while(timeout-- && !info->irq_occurred)
4978 msleep_interruptible(10);
4979
4980 spin_lock_irqsave(&info->lock,flags);
4981 reset_port(info);
4982 spin_unlock_irqrestore(&info->lock,flags);
4983
4984 info->params.data_rate = speed;
4985 info->port.tty = oldtty;
4986
4987 info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4988 return info->irq_occurred ? 0 : -ENODEV;
4989}
4990
4991static int loopback_test_rx(struct slgt_info *info)
4992{
4993 unsigned char *src, *dest;
4994 int count;
4995
4996 if (desc_complete(info->rbufs[0])) {
4997 count = desc_count(info->rbufs[0]);
4998 src = info->rbufs[0].buf;
4999 dest = info->tmp_rbuf;
5000
5001 for( ; count ; count-=2, src+=2) {
5002 /* src=data byte (src+1)=status byte */
5003 if (!(*(src+1) & (BIT9 + BIT8))) {
5004 *dest = *src;
5005 dest++;
5006 info->tmp_rbuf_count++;
5007 }
5008 }
5009 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
5010 return 1;
5011 }
5012 return 0;
5013}
5014
5015static int loopback_test(struct slgt_info *info)
5016{
5017#define TESTFRAMESIZE 20
5018
5019 unsigned long timeout;
5020 u16 count = TESTFRAMESIZE;
5021 unsigned char buf[TESTFRAMESIZE];
5022 int rc = -ENODEV;
5023 unsigned long flags;
5024
5025 struct tty_struct *oldtty = info->port.tty;
5026 MGSL_PARAMS params;
5027
5028 memcpy(¶ms, &info->params, sizeof(params));
5029
5030 info->params.mode = MGSL_MODE_ASYNC;
5031 info->params.data_rate = 921600;
5032 info->params.loopback = 1;
5033 info->port.tty = NULL;
5034
5035 /* build and send transmit frame */
5036 for (count = 0; count < TESTFRAMESIZE; ++count)
5037 buf[count] = (unsigned char)count;
5038
5039 info->tmp_rbuf_count = 0;
5040 memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
5041
5042 /* program hardware for HDLC and enabled receiver */
5043 spin_lock_irqsave(&info->lock,flags);
5044 async_mode(info);
5045 rx_start(info);
5046 tx_load(info, buf, count);
5047 spin_unlock_irqrestore(&info->lock, flags);
5048
5049 /* wait for receive complete */
5050 for (timeout = 100; timeout; --timeout) {
5051 msleep_interruptible(10);
5052 if (loopback_test_rx(info)) {
5053 rc = 0;
5054 break;
5055 }
5056 }
5057
5058 /* verify received frame length and contents */
5059 if (!rc && (info->tmp_rbuf_count != count ||
5060 memcmp(buf, info->tmp_rbuf, count))) {
5061 rc = -ENODEV;
5062 }
5063
5064 spin_lock_irqsave(&info->lock,flags);
5065 reset_adapter(info);
5066 spin_unlock_irqrestore(&info->lock,flags);
5067
5068 memcpy(&info->params, ¶ms, sizeof(info->params));
5069 info->port.tty = oldtty;
5070
5071 info->init_error = rc ? DiagStatus_DmaFailure : 0;
5072 return rc;
5073}
5074
5075static int adapter_test(struct slgt_info *info)
5076{
5077 DBGINFO(("testing %s\n", info->device_name));
5078 if (register_test(info) < 0) {
5079 printk("register test failure %s addr=%08X\n",
5080 info->device_name, info->phys_reg_addr);
5081 } else if (irq_test(info) < 0) {
5082 printk("IRQ test failure %s IRQ=%d\n",
5083 info->device_name, info->irq_level);
5084 } else if (loopback_test(info) < 0) {
5085 printk("loopback test failure %s\n", info->device_name);
5086 }
5087 return info->init_error;
5088}
5089
5090/*
5091 * transmit timeout handler
5092 */
5093static void tx_timeout(struct timer_list *t)
5094{
5095 struct slgt_info *info = from_timer(info, t, tx_timer);
5096 unsigned long flags;
5097
5098 DBGINFO(("%s tx_timeout\n", info->device_name));
5099 if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5100 info->icount.txtimeout++;
5101 }
5102 spin_lock_irqsave(&info->lock,flags);
5103 tx_stop(info);
5104 spin_unlock_irqrestore(&info->lock,flags);
5105
5106#if SYNCLINK_GENERIC_HDLC
5107 if (info->netcount)
5108 hdlcdev_tx_done(info);
5109 else
5110#endif
5111 bh_transmit(info);
5112}
5113
5114/*
5115 * receive buffer polling timer
5116 */
5117static void rx_timeout(struct timer_list *t)
5118{
5119 struct slgt_info *info = from_timer(info, t, rx_timer);
5120 unsigned long flags;
5121
5122 DBGINFO(("%s rx_timeout\n", info->device_name));
5123 spin_lock_irqsave(&info->lock, flags);
5124 info->pending_bh |= BH_RECEIVE;
5125 spin_unlock_irqrestore(&info->lock, flags);
5126 bh_handler(&info->task);
5127}
5128
1// SPDX-License-Identifier: GPL-1.0+
2/*
3 * Device driver for Microgate SyncLink GT serial adapters.
4 *
5 * written by Paul Fulghum for Microgate Corporation
6 * paulkf@microgate.com
7 *
8 * Microgate and SyncLink are trademarks of Microgate Corporation
9 *
10 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
11 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
12 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
13 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
14 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
15 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
16 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
17 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
18 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
19 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
20 * OF THE POSSIBILITY OF SUCH DAMAGE.
21 */
22
23/*
24 * DEBUG OUTPUT DEFINITIONS
25 *
26 * uncomment lines below to enable specific types of debug output
27 *
28 * DBGINFO information - most verbose output
29 * DBGERR serious errors
30 * DBGBH bottom half service routine debugging
31 * DBGISR interrupt service routine debugging
32 * DBGDATA output receive and transmit data
33 * DBGTBUF output transmit DMA buffers and registers
34 * DBGRBUF output receive DMA buffers and registers
35 */
36
37#define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
38#define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
39#define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
40#define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
41#define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
42/*#define DBGTBUF(info) dump_tbufs(info)*/
43/*#define DBGRBUF(info) dump_rbufs(info)*/
44
45
46#include <linux/module.h>
47#include <linux/errno.h>
48#include <linux/signal.h>
49#include <linux/sched.h>
50#include <linux/timer.h>
51#include <linux/interrupt.h>
52#include <linux/pci.h>
53#include <linux/tty.h>
54#include <linux/tty_flip.h>
55#include <linux/serial.h>
56#include <linux/major.h>
57#include <linux/string.h>
58#include <linux/fcntl.h>
59#include <linux/ptrace.h>
60#include <linux/ioport.h>
61#include <linux/mm.h>
62#include <linux/seq_file.h>
63#include <linux/slab.h>
64#include <linux/netdevice.h>
65#include <linux/vmalloc.h>
66#include <linux/init.h>
67#include <linux/delay.h>
68#include <linux/ioctl.h>
69#include <linux/termios.h>
70#include <linux/bitops.h>
71#include <linux/workqueue.h>
72#include <linux/hdlc.h>
73#include <linux/synclink.h>
74
75#include <asm/io.h>
76#include <asm/irq.h>
77#include <asm/dma.h>
78#include <asm/types.h>
79#include <linux/uaccess.h>
80
81#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
82#define SYNCLINK_GENERIC_HDLC 1
83#else
84#define SYNCLINK_GENERIC_HDLC 0
85#endif
86
87/*
88 * module identification
89 */
90static char *driver_name = "SyncLink GT";
91static char *slgt_driver_name = "synclink_gt";
92static char *tty_dev_prefix = "ttySLG";
93MODULE_LICENSE("GPL");
94#define MGSL_MAGIC 0x5401
95#define MAX_DEVICES 32
96
97static const struct pci_device_id pci_table[] = {
98 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
99 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
100 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
101 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
102 {0,}, /* terminate list */
103};
104MODULE_DEVICE_TABLE(pci, pci_table);
105
106static int init_one(struct pci_dev *dev,const struct pci_device_id *ent);
107static void remove_one(struct pci_dev *dev);
108static struct pci_driver pci_driver = {
109 .name = "synclink_gt",
110 .id_table = pci_table,
111 .probe = init_one,
112 .remove = remove_one,
113};
114
115static bool pci_registered;
116
117/*
118 * module configuration and status
119 */
120static struct slgt_info *slgt_device_list;
121static int slgt_device_count;
122
123static int ttymajor;
124static int debug_level;
125static int maxframe[MAX_DEVICES];
126
127module_param(ttymajor, int, 0);
128module_param(debug_level, int, 0);
129module_param_array(maxframe, int, NULL, 0);
130
131MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
132MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
133MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
134
135/*
136 * tty support and callbacks
137 */
138static struct tty_driver *serial_driver;
139
140static void wait_until_sent(struct tty_struct *tty, int timeout);
141static void flush_buffer(struct tty_struct *tty);
142static void tx_release(struct tty_struct *tty);
143
144/*
145 * generic HDLC support
146 */
147#define dev_to_port(D) (dev_to_hdlc(D)->priv)
148
149
150/*
151 * device specific structures, macros and functions
152 */
153
154#define SLGT_MAX_PORTS 4
155#define SLGT_REG_SIZE 256
156
157/*
158 * conditional wait facility
159 */
160struct cond_wait {
161 struct cond_wait *next;
162 wait_queue_head_t q;
163 wait_queue_entry_t wait;
164 unsigned int data;
165};
166static void flush_cond_wait(struct cond_wait **head);
167
168/*
169 * DMA buffer descriptor and access macros
170 */
171struct slgt_desc
172{
173 __le16 count;
174 __le16 status;
175 __le32 pbuf; /* physical address of data buffer */
176 __le32 next; /* physical address of next descriptor */
177
178 /* driver book keeping */
179 char *buf; /* virtual address of data buffer */
180 unsigned int pdesc; /* physical address of this descriptor */
181 dma_addr_t buf_dma_addr;
182 unsigned short buf_count;
183};
184
185#define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
186#define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b))
187#define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b))
188#define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
189#define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
190#define desc_count(a) (le16_to_cpu((a).count))
191#define desc_status(a) (le16_to_cpu((a).status))
192#define desc_complete(a) (le16_to_cpu((a).status) & BIT15)
193#define desc_eof(a) (le16_to_cpu((a).status) & BIT2)
194#define desc_crc_error(a) (le16_to_cpu((a).status) & BIT1)
195#define desc_abort(a) (le16_to_cpu((a).status) & BIT0)
196#define desc_residue(a) ((le16_to_cpu((a).status) & 0x38) >> 3)
197
198struct _input_signal_events {
199 int ri_up;
200 int ri_down;
201 int dsr_up;
202 int dsr_down;
203 int dcd_up;
204 int dcd_down;
205 int cts_up;
206 int cts_down;
207};
208
209/*
210 * device instance data structure
211 */
212struct slgt_info {
213 void *if_ptr; /* General purpose pointer (used by SPPP) */
214 struct tty_port port;
215
216 struct slgt_info *next_device; /* device list link */
217
218 int magic;
219
220 char device_name[25];
221 struct pci_dev *pdev;
222
223 int port_count; /* count of ports on adapter */
224 int adapter_num; /* adapter instance number */
225 int port_num; /* port instance number */
226
227 /* array of pointers to port contexts on this adapter */
228 struct slgt_info *port_array[SLGT_MAX_PORTS];
229
230 int line; /* tty line instance number */
231
232 struct mgsl_icount icount;
233
234 int timeout;
235 int x_char; /* xon/xoff character */
236 unsigned int read_status_mask;
237 unsigned int ignore_status_mask;
238
239 wait_queue_head_t status_event_wait_q;
240 wait_queue_head_t event_wait_q;
241 struct timer_list tx_timer;
242 struct timer_list rx_timer;
243
244 unsigned int gpio_present;
245 struct cond_wait *gpio_wait_q;
246
247 spinlock_t lock; /* spinlock for synchronizing with ISR */
248
249 struct work_struct task;
250 u32 pending_bh;
251 bool bh_requested;
252 bool bh_running;
253
254 int isr_overflow;
255 bool irq_requested; /* true if IRQ requested */
256 bool irq_occurred; /* for diagnostics use */
257
258 /* device configuration */
259
260 unsigned int bus_type;
261 unsigned int irq_level;
262 unsigned long irq_flags;
263
264 unsigned char __iomem * reg_addr; /* memory mapped registers address */
265 u32 phys_reg_addr;
266 bool reg_addr_requested;
267
268 MGSL_PARAMS params; /* communications parameters */
269 u32 idle_mode;
270 u32 max_frame_size; /* as set by device config */
271
272 unsigned int rbuf_fill_level;
273 unsigned int rx_pio;
274 unsigned int if_mode;
275 unsigned int base_clock;
276 unsigned int xsync;
277 unsigned int xctrl;
278
279 /* device status */
280
281 bool rx_enabled;
282 bool rx_restart;
283
284 bool tx_enabled;
285 bool tx_active;
286
287 unsigned char signals; /* serial signal states */
288 int init_error; /* initialization error */
289
290 unsigned char *tx_buf;
291 int tx_count;
292
293 char *flag_buf;
294 bool drop_rts_on_tx_done;
295 struct _input_signal_events input_signal_events;
296
297 int dcd_chkcount; /* check counts to prevent */
298 int cts_chkcount; /* too many IRQs if a signal */
299 int dsr_chkcount; /* is floating */
300 int ri_chkcount;
301
302 char *bufs; /* virtual address of DMA buffer lists */
303 dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
304
305 unsigned int rbuf_count;
306 struct slgt_desc *rbufs;
307 unsigned int rbuf_current;
308 unsigned int rbuf_index;
309 unsigned int rbuf_fill_index;
310 unsigned short rbuf_fill_count;
311
312 unsigned int tbuf_count;
313 struct slgt_desc *tbufs;
314 unsigned int tbuf_current;
315 unsigned int tbuf_start;
316
317 unsigned char *tmp_rbuf;
318 unsigned int tmp_rbuf_count;
319
320 /* SPPP/Cisco HDLC device parts */
321
322 int netcount;
323 spinlock_t netlock;
324#if SYNCLINK_GENERIC_HDLC
325 struct net_device *netdev;
326#endif
327
328};
329
330static MGSL_PARAMS default_params = {
331 .mode = MGSL_MODE_HDLC,
332 .loopback = 0,
333 .flags = HDLC_FLAG_UNDERRUN_ABORT15,
334 .encoding = HDLC_ENCODING_NRZI_SPACE,
335 .clock_speed = 0,
336 .addr_filter = 0xff,
337 .crc_type = HDLC_CRC_16_CCITT,
338 .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
339 .preamble = HDLC_PREAMBLE_PATTERN_NONE,
340 .data_rate = 9600,
341 .data_bits = 8,
342 .stop_bits = 1,
343 .parity = ASYNC_PARITY_NONE
344};
345
346
347#define BH_RECEIVE 1
348#define BH_TRANSMIT 2
349#define BH_STATUS 4
350#define IO_PIN_SHUTDOWN_LIMIT 100
351
352#define DMABUFSIZE 256
353#define DESC_LIST_SIZE 4096
354
355#define MASK_PARITY BIT1
356#define MASK_FRAMING BIT0
357#define MASK_BREAK BIT14
358#define MASK_OVERRUN BIT4
359
360#define GSR 0x00 /* global status */
361#define JCR 0x04 /* JTAG control */
362#define IODR 0x08 /* GPIO direction */
363#define IOER 0x0c /* GPIO interrupt enable */
364#define IOVR 0x10 /* GPIO value */
365#define IOSR 0x14 /* GPIO interrupt status */
366#define TDR 0x80 /* tx data */
367#define RDR 0x80 /* rx data */
368#define TCR 0x82 /* tx control */
369#define TIR 0x84 /* tx idle */
370#define TPR 0x85 /* tx preamble */
371#define RCR 0x86 /* rx control */
372#define VCR 0x88 /* V.24 control */
373#define CCR 0x89 /* clock control */
374#define BDR 0x8a /* baud divisor */
375#define SCR 0x8c /* serial control */
376#define SSR 0x8e /* serial status */
377#define RDCSR 0x90 /* rx DMA control/status */
378#define TDCSR 0x94 /* tx DMA control/status */
379#define RDDAR 0x98 /* rx DMA descriptor address */
380#define TDDAR 0x9c /* tx DMA descriptor address */
381#define XSR 0x40 /* extended sync pattern */
382#define XCR 0x44 /* extended control */
383
384#define RXIDLE BIT14
385#define RXBREAK BIT14
386#define IRQ_TXDATA BIT13
387#define IRQ_TXIDLE BIT12
388#define IRQ_TXUNDER BIT11 /* HDLC */
389#define IRQ_RXDATA BIT10
390#define IRQ_RXIDLE BIT9 /* HDLC */
391#define IRQ_RXBREAK BIT9 /* async */
392#define IRQ_RXOVER BIT8
393#define IRQ_DSR BIT7
394#define IRQ_CTS BIT6
395#define IRQ_DCD BIT5
396#define IRQ_RI BIT4
397#define IRQ_ALL 0x3ff0
398#define IRQ_MASTER BIT0
399
400#define slgt_irq_on(info, mask) \
401 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
402#define slgt_irq_off(info, mask) \
403 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
404
405static __u8 rd_reg8(struct slgt_info *info, unsigned int addr);
406static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
407static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
408static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
409static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
410static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
411
412static void msc_set_vcr(struct slgt_info *info);
413
414static int startup(struct slgt_info *info);
415static int block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
416static void shutdown(struct slgt_info *info);
417static void program_hw(struct slgt_info *info);
418static void change_params(struct slgt_info *info);
419
420static int adapter_test(struct slgt_info *info);
421
422static void reset_port(struct slgt_info *info);
423static void async_mode(struct slgt_info *info);
424static void sync_mode(struct slgt_info *info);
425
426static void rx_stop(struct slgt_info *info);
427static void rx_start(struct slgt_info *info);
428static void reset_rbufs(struct slgt_info *info);
429static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
430static bool rx_get_frame(struct slgt_info *info);
431static bool rx_get_buf(struct slgt_info *info);
432
433static void tx_start(struct slgt_info *info);
434static void tx_stop(struct slgt_info *info);
435static void tx_set_idle(struct slgt_info *info);
436static unsigned int tbuf_bytes(struct slgt_info *info);
437static void reset_tbufs(struct slgt_info *info);
438static void tdma_reset(struct slgt_info *info);
439static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
440
441static void get_gtsignals(struct slgt_info *info);
442static void set_gtsignals(struct slgt_info *info);
443static void set_rate(struct slgt_info *info, u32 data_rate);
444
445static void bh_transmit(struct slgt_info *info);
446static void isr_txeom(struct slgt_info *info, unsigned short status);
447
448static void tx_timeout(struct timer_list *t);
449static void rx_timeout(struct timer_list *t);
450
451/*
452 * ioctl handlers
453 */
454static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
455static int get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
456static int set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
457static int get_txidle(struct slgt_info *info, int __user *idle_mode);
458static int set_txidle(struct slgt_info *info, int idle_mode);
459static int tx_enable(struct slgt_info *info, int enable);
460static int tx_abort(struct slgt_info *info);
461static int rx_enable(struct slgt_info *info, int enable);
462static int modem_input_wait(struct slgt_info *info,int arg);
463static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
464static int get_interface(struct slgt_info *info, int __user *if_mode);
465static int set_interface(struct slgt_info *info, int if_mode);
466static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
467static int get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
468static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
469static int get_xsync(struct slgt_info *info, int __user *if_mode);
470static int set_xsync(struct slgt_info *info, int if_mode);
471static int get_xctrl(struct slgt_info *info, int __user *if_mode);
472static int set_xctrl(struct slgt_info *info, int if_mode);
473
474/*
475 * driver functions
476 */
477static void release_resources(struct slgt_info *info);
478
479/*
480 * DEBUG OUTPUT CODE
481 */
482#ifndef DBGINFO
483#define DBGINFO(fmt)
484#endif
485#ifndef DBGERR
486#define DBGERR(fmt)
487#endif
488#ifndef DBGBH
489#define DBGBH(fmt)
490#endif
491#ifndef DBGISR
492#define DBGISR(fmt)
493#endif
494
495#ifdef DBGDATA
496static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
497{
498 int i;
499 int linecount;
500 printk("%s %s data:\n",info->device_name, label);
501 while(count) {
502 linecount = (count > 16) ? 16 : count;
503 for(i=0; i < linecount; i++)
504 printk("%02X ",(unsigned char)data[i]);
505 for(;i<17;i++)
506 printk(" ");
507 for(i=0;i<linecount;i++) {
508 if (data[i]>=040 && data[i]<=0176)
509 printk("%c",data[i]);
510 else
511 printk(".");
512 }
513 printk("\n");
514 data += linecount;
515 count -= linecount;
516 }
517}
518#else
519#define DBGDATA(info, buf, size, label)
520#endif
521
522#ifdef DBGTBUF
523static void dump_tbufs(struct slgt_info *info)
524{
525 int i;
526 printk("tbuf_current=%d\n", info->tbuf_current);
527 for (i=0 ; i < info->tbuf_count ; i++) {
528 printk("%d: count=%04X status=%04X\n",
529 i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
530 }
531}
532#else
533#define DBGTBUF(info)
534#endif
535
536#ifdef DBGRBUF
537static void dump_rbufs(struct slgt_info *info)
538{
539 int i;
540 printk("rbuf_current=%d\n", info->rbuf_current);
541 for (i=0 ; i < info->rbuf_count ; i++) {
542 printk("%d: count=%04X status=%04X\n",
543 i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
544 }
545}
546#else
547#define DBGRBUF(info)
548#endif
549
550static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
551{
552#ifdef SANITY_CHECK
553 if (!info) {
554 printk("null struct slgt_info for (%s) in %s\n", devname, name);
555 return 1;
556 }
557 if (info->magic != MGSL_MAGIC) {
558 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
559 return 1;
560 }
561#else
562 if (!info)
563 return 1;
564#endif
565 return 0;
566}
567
568/*
569 * line discipline callback wrappers
570 *
571 * The wrappers maintain line discipline references
572 * while calling into the line discipline.
573 *
574 * ldisc_receive_buf - pass receive data to line discipline
575 */
576static void ldisc_receive_buf(struct tty_struct *tty,
577 const __u8 *data, char *flags, int count)
578{
579 struct tty_ldisc *ld;
580 if (!tty)
581 return;
582 ld = tty_ldisc_ref(tty);
583 if (ld) {
584 if (ld->ops->receive_buf)
585 ld->ops->receive_buf(tty, data, flags, count);
586 tty_ldisc_deref(ld);
587 }
588}
589
590/* tty callbacks */
591
592static int open(struct tty_struct *tty, struct file *filp)
593{
594 struct slgt_info *info;
595 int retval, line;
596 unsigned long flags;
597
598 line = tty->index;
599 if (line >= slgt_device_count) {
600 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
601 return -ENODEV;
602 }
603
604 info = slgt_device_list;
605 while(info && info->line != line)
606 info = info->next_device;
607 if (sanity_check(info, tty->name, "open"))
608 return -ENODEV;
609 if (info->init_error) {
610 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
611 return -ENODEV;
612 }
613
614 tty->driver_data = info;
615 info->port.tty = tty;
616
617 DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
618
619 mutex_lock(&info->port.mutex);
620
621 spin_lock_irqsave(&info->netlock, flags);
622 if (info->netcount) {
623 retval = -EBUSY;
624 spin_unlock_irqrestore(&info->netlock, flags);
625 mutex_unlock(&info->port.mutex);
626 goto cleanup;
627 }
628 info->port.count++;
629 spin_unlock_irqrestore(&info->netlock, flags);
630
631 if (info->port.count == 1) {
632 /* 1st open on this device, init hardware */
633 retval = startup(info);
634 if (retval < 0) {
635 mutex_unlock(&info->port.mutex);
636 goto cleanup;
637 }
638 }
639 mutex_unlock(&info->port.mutex);
640 retval = block_til_ready(tty, filp, info);
641 if (retval) {
642 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
643 goto cleanup;
644 }
645
646 retval = 0;
647
648cleanup:
649 if (retval) {
650 if (tty->count == 1)
651 info->port.tty = NULL; /* tty layer will release tty struct */
652 if(info->port.count)
653 info->port.count--;
654 }
655
656 DBGINFO(("%s open rc=%d\n", info->device_name, retval));
657 return retval;
658}
659
660static void close(struct tty_struct *tty, struct file *filp)
661{
662 struct slgt_info *info = tty->driver_data;
663
664 if (sanity_check(info, tty->name, "close"))
665 return;
666 DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
667
668 if (tty_port_close_start(&info->port, tty, filp) == 0)
669 goto cleanup;
670
671 mutex_lock(&info->port.mutex);
672 if (tty_port_initialized(&info->port))
673 wait_until_sent(tty, info->timeout);
674 flush_buffer(tty);
675 tty_ldisc_flush(tty);
676
677 shutdown(info);
678 mutex_unlock(&info->port.mutex);
679
680 tty_port_close_end(&info->port, tty);
681 info->port.tty = NULL;
682cleanup:
683 DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
684}
685
686static void hangup(struct tty_struct *tty)
687{
688 struct slgt_info *info = tty->driver_data;
689 unsigned long flags;
690
691 if (sanity_check(info, tty->name, "hangup"))
692 return;
693 DBGINFO(("%s hangup\n", info->device_name));
694
695 flush_buffer(tty);
696
697 mutex_lock(&info->port.mutex);
698 shutdown(info);
699
700 spin_lock_irqsave(&info->port.lock, flags);
701 info->port.count = 0;
702 info->port.tty = NULL;
703 spin_unlock_irqrestore(&info->port.lock, flags);
704 tty_port_set_active(&info->port, 0);
705 mutex_unlock(&info->port.mutex);
706
707 wake_up_interruptible(&info->port.open_wait);
708}
709
710static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
711{
712 struct slgt_info *info = tty->driver_data;
713 unsigned long flags;
714
715 DBGINFO(("%s set_termios\n", tty->driver->name));
716
717 change_params(info);
718
719 /* Handle transition to B0 status */
720 if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) {
721 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
722 spin_lock_irqsave(&info->lock,flags);
723 set_gtsignals(info);
724 spin_unlock_irqrestore(&info->lock,flags);
725 }
726
727 /* Handle transition away from B0 status */
728 if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
729 info->signals |= SerialSignal_DTR;
730 if (!C_CRTSCTS(tty) || !tty_throttled(tty))
731 info->signals |= SerialSignal_RTS;
732 spin_lock_irqsave(&info->lock,flags);
733 set_gtsignals(info);
734 spin_unlock_irqrestore(&info->lock,flags);
735 }
736
737 /* Handle turning off CRTSCTS */
738 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
739 tty->hw_stopped = 0;
740 tx_release(tty);
741 }
742}
743
744static void update_tx_timer(struct slgt_info *info)
745{
746 /*
747 * use worst case speed of 1200bps to calculate transmit timeout
748 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
749 */
750 if (info->params.mode == MGSL_MODE_HDLC) {
751 int timeout = (tbuf_bytes(info) * 7) + 1000;
752 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
753 }
754}
755
756static int write(struct tty_struct *tty,
757 const unsigned char *buf, int count)
758{
759 int ret = 0;
760 struct slgt_info *info = tty->driver_data;
761 unsigned long flags;
762
763 if (sanity_check(info, tty->name, "write"))
764 return -EIO;
765
766 DBGINFO(("%s write count=%d\n", info->device_name, count));
767
768 if (!info->tx_buf || (count > info->max_frame_size))
769 return -EIO;
770
771 if (!count || tty->flow.stopped || tty->hw_stopped)
772 return 0;
773
774 spin_lock_irqsave(&info->lock, flags);
775
776 if (info->tx_count) {
777 /* send accumulated data from send_char() */
778 if (!tx_load(info, info->tx_buf, info->tx_count))
779 goto cleanup;
780 info->tx_count = 0;
781 }
782
783 if (tx_load(info, buf, count))
784 ret = count;
785
786cleanup:
787 spin_unlock_irqrestore(&info->lock, flags);
788 DBGINFO(("%s write rc=%d\n", info->device_name, ret));
789 return ret;
790}
791
792static int put_char(struct tty_struct *tty, unsigned char ch)
793{
794 struct slgt_info *info = tty->driver_data;
795 unsigned long flags;
796 int ret = 0;
797
798 if (sanity_check(info, tty->name, "put_char"))
799 return 0;
800 DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
801 if (!info->tx_buf)
802 return 0;
803 spin_lock_irqsave(&info->lock,flags);
804 if (info->tx_count < info->max_frame_size) {
805 info->tx_buf[info->tx_count++] = ch;
806 ret = 1;
807 }
808 spin_unlock_irqrestore(&info->lock,flags);
809 return ret;
810}
811
812static void send_xchar(struct tty_struct *tty, char ch)
813{
814 struct slgt_info *info = tty->driver_data;
815 unsigned long flags;
816
817 if (sanity_check(info, tty->name, "send_xchar"))
818 return;
819 DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
820 info->x_char = ch;
821 if (ch) {
822 spin_lock_irqsave(&info->lock,flags);
823 if (!info->tx_enabled)
824 tx_start(info);
825 spin_unlock_irqrestore(&info->lock,flags);
826 }
827}
828
829static void wait_until_sent(struct tty_struct *tty, int timeout)
830{
831 struct slgt_info *info = tty->driver_data;
832 unsigned long orig_jiffies, char_time;
833
834 if (!info )
835 return;
836 if (sanity_check(info, tty->name, "wait_until_sent"))
837 return;
838 DBGINFO(("%s wait_until_sent entry\n", info->device_name));
839 if (!tty_port_initialized(&info->port))
840 goto exit;
841
842 orig_jiffies = jiffies;
843
844 /* Set check interval to 1/5 of estimated time to
845 * send a character, and make it at least 1. The check
846 * interval should also be less than the timeout.
847 * Note: use tight timings here to satisfy the NIST-PCTS.
848 */
849
850 if (info->params.data_rate) {
851 char_time = info->timeout/(32 * 5);
852 if (!char_time)
853 char_time++;
854 } else
855 char_time = 1;
856
857 if (timeout)
858 char_time = min_t(unsigned long, char_time, timeout);
859
860 while (info->tx_active) {
861 msleep_interruptible(jiffies_to_msecs(char_time));
862 if (signal_pending(current))
863 break;
864 if (timeout && time_after(jiffies, orig_jiffies + timeout))
865 break;
866 }
867exit:
868 DBGINFO(("%s wait_until_sent exit\n", info->device_name));
869}
870
871static unsigned int write_room(struct tty_struct *tty)
872{
873 struct slgt_info *info = tty->driver_data;
874 unsigned int ret;
875
876 if (sanity_check(info, tty->name, "write_room"))
877 return 0;
878 ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
879 DBGINFO(("%s write_room=%u\n", info->device_name, ret));
880 return ret;
881}
882
883static void flush_chars(struct tty_struct *tty)
884{
885 struct slgt_info *info = tty->driver_data;
886 unsigned long flags;
887
888 if (sanity_check(info, tty->name, "flush_chars"))
889 return;
890 DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
891
892 if (info->tx_count <= 0 || tty->flow.stopped ||
893 tty->hw_stopped || !info->tx_buf)
894 return;
895
896 DBGINFO(("%s flush_chars start transmit\n", info->device_name));
897
898 spin_lock_irqsave(&info->lock,flags);
899 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
900 info->tx_count = 0;
901 spin_unlock_irqrestore(&info->lock,flags);
902}
903
904static void flush_buffer(struct tty_struct *tty)
905{
906 struct slgt_info *info = tty->driver_data;
907 unsigned long flags;
908
909 if (sanity_check(info, tty->name, "flush_buffer"))
910 return;
911 DBGINFO(("%s flush_buffer\n", info->device_name));
912
913 spin_lock_irqsave(&info->lock, flags);
914 info->tx_count = 0;
915 spin_unlock_irqrestore(&info->lock, flags);
916
917 tty_wakeup(tty);
918}
919
920/*
921 * throttle (stop) transmitter
922 */
923static void tx_hold(struct tty_struct *tty)
924{
925 struct slgt_info *info = tty->driver_data;
926 unsigned long flags;
927
928 if (sanity_check(info, tty->name, "tx_hold"))
929 return;
930 DBGINFO(("%s tx_hold\n", info->device_name));
931 spin_lock_irqsave(&info->lock,flags);
932 if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
933 tx_stop(info);
934 spin_unlock_irqrestore(&info->lock,flags);
935}
936
937/*
938 * release (start) transmitter
939 */
940static void tx_release(struct tty_struct *tty)
941{
942 struct slgt_info *info = tty->driver_data;
943 unsigned long flags;
944
945 if (sanity_check(info, tty->name, "tx_release"))
946 return;
947 DBGINFO(("%s tx_release\n", info->device_name));
948 spin_lock_irqsave(&info->lock, flags);
949 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
950 info->tx_count = 0;
951 spin_unlock_irqrestore(&info->lock, flags);
952}
953
954/*
955 * Service an IOCTL request
956 *
957 * Arguments
958 *
959 * tty pointer to tty instance data
960 * cmd IOCTL command code
961 * arg command argument/context
962 *
963 * Return 0 if success, otherwise error code
964 */
965static int ioctl(struct tty_struct *tty,
966 unsigned int cmd, unsigned long arg)
967{
968 struct slgt_info *info = tty->driver_data;
969 void __user *argp = (void __user *)arg;
970 int ret;
971
972 if (sanity_check(info, tty->name, "ioctl"))
973 return -ENODEV;
974 DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
975
976 if (cmd != TIOCMIWAIT) {
977 if (tty_io_error(tty))
978 return -EIO;
979 }
980
981 switch (cmd) {
982 case MGSL_IOCWAITEVENT:
983 return wait_mgsl_event(info, argp);
984 case TIOCMIWAIT:
985 return modem_input_wait(info,(int)arg);
986 case MGSL_IOCSGPIO:
987 return set_gpio(info, argp);
988 case MGSL_IOCGGPIO:
989 return get_gpio(info, argp);
990 case MGSL_IOCWAITGPIO:
991 return wait_gpio(info, argp);
992 case MGSL_IOCGXSYNC:
993 return get_xsync(info, argp);
994 case MGSL_IOCSXSYNC:
995 return set_xsync(info, (int)arg);
996 case MGSL_IOCGXCTRL:
997 return get_xctrl(info, argp);
998 case MGSL_IOCSXCTRL:
999 return set_xctrl(info, (int)arg);
1000 }
1001 mutex_lock(&info->port.mutex);
1002 switch (cmd) {
1003 case MGSL_IOCGPARAMS:
1004 ret = get_params(info, argp);
1005 break;
1006 case MGSL_IOCSPARAMS:
1007 ret = set_params(info, argp);
1008 break;
1009 case MGSL_IOCGTXIDLE:
1010 ret = get_txidle(info, argp);
1011 break;
1012 case MGSL_IOCSTXIDLE:
1013 ret = set_txidle(info, (int)arg);
1014 break;
1015 case MGSL_IOCTXENABLE:
1016 ret = tx_enable(info, (int)arg);
1017 break;
1018 case MGSL_IOCRXENABLE:
1019 ret = rx_enable(info, (int)arg);
1020 break;
1021 case MGSL_IOCTXABORT:
1022 ret = tx_abort(info);
1023 break;
1024 case MGSL_IOCGSTATS:
1025 ret = get_stats(info, argp);
1026 break;
1027 case MGSL_IOCGIF:
1028 ret = get_interface(info, argp);
1029 break;
1030 case MGSL_IOCSIF:
1031 ret = set_interface(info,(int)arg);
1032 break;
1033 default:
1034 ret = -ENOIOCTLCMD;
1035 }
1036 mutex_unlock(&info->port.mutex);
1037 return ret;
1038}
1039
1040static int get_icount(struct tty_struct *tty,
1041 struct serial_icounter_struct *icount)
1042
1043{
1044 struct slgt_info *info = tty->driver_data;
1045 struct mgsl_icount cnow; /* kernel counter temps */
1046 unsigned long flags;
1047
1048 spin_lock_irqsave(&info->lock,flags);
1049 cnow = info->icount;
1050 spin_unlock_irqrestore(&info->lock,flags);
1051
1052 icount->cts = cnow.cts;
1053 icount->dsr = cnow.dsr;
1054 icount->rng = cnow.rng;
1055 icount->dcd = cnow.dcd;
1056 icount->rx = cnow.rx;
1057 icount->tx = cnow.tx;
1058 icount->frame = cnow.frame;
1059 icount->overrun = cnow.overrun;
1060 icount->parity = cnow.parity;
1061 icount->brk = cnow.brk;
1062 icount->buf_overrun = cnow.buf_overrun;
1063
1064 return 0;
1065}
1066
1067/*
1068 * support for 32 bit ioctl calls on 64 bit systems
1069 */
1070#ifdef CONFIG_COMPAT
1071static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1072{
1073 struct MGSL_PARAMS32 tmp_params;
1074
1075 DBGINFO(("%s get_params32\n", info->device_name));
1076 memset(&tmp_params, 0, sizeof(tmp_params));
1077 tmp_params.mode = (compat_ulong_t)info->params.mode;
1078 tmp_params.loopback = info->params.loopback;
1079 tmp_params.flags = info->params.flags;
1080 tmp_params.encoding = info->params.encoding;
1081 tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed;
1082 tmp_params.addr_filter = info->params.addr_filter;
1083 tmp_params.crc_type = info->params.crc_type;
1084 tmp_params.preamble_length = info->params.preamble_length;
1085 tmp_params.preamble = info->params.preamble;
1086 tmp_params.data_rate = (compat_ulong_t)info->params.data_rate;
1087 tmp_params.data_bits = info->params.data_bits;
1088 tmp_params.stop_bits = info->params.stop_bits;
1089 tmp_params.parity = info->params.parity;
1090 if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1091 return -EFAULT;
1092 return 0;
1093}
1094
1095static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1096{
1097 struct MGSL_PARAMS32 tmp_params;
1098
1099 DBGINFO(("%s set_params32\n", info->device_name));
1100 if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1101 return -EFAULT;
1102
1103 spin_lock(&info->lock);
1104 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1105 info->base_clock = tmp_params.clock_speed;
1106 } else {
1107 info->params.mode = tmp_params.mode;
1108 info->params.loopback = tmp_params.loopback;
1109 info->params.flags = tmp_params.flags;
1110 info->params.encoding = tmp_params.encoding;
1111 info->params.clock_speed = tmp_params.clock_speed;
1112 info->params.addr_filter = tmp_params.addr_filter;
1113 info->params.crc_type = tmp_params.crc_type;
1114 info->params.preamble_length = tmp_params.preamble_length;
1115 info->params.preamble = tmp_params.preamble;
1116 info->params.data_rate = tmp_params.data_rate;
1117 info->params.data_bits = tmp_params.data_bits;
1118 info->params.stop_bits = tmp_params.stop_bits;
1119 info->params.parity = tmp_params.parity;
1120 }
1121 spin_unlock(&info->lock);
1122
1123 program_hw(info);
1124
1125 return 0;
1126}
1127
1128static long slgt_compat_ioctl(struct tty_struct *tty,
1129 unsigned int cmd, unsigned long arg)
1130{
1131 struct slgt_info *info = tty->driver_data;
1132 int rc;
1133
1134 if (sanity_check(info, tty->name, "compat_ioctl"))
1135 return -ENODEV;
1136 DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1137
1138 switch (cmd) {
1139 case MGSL_IOCSPARAMS32:
1140 rc = set_params32(info, compat_ptr(arg));
1141 break;
1142
1143 case MGSL_IOCGPARAMS32:
1144 rc = get_params32(info, compat_ptr(arg));
1145 break;
1146
1147 case MGSL_IOCGPARAMS:
1148 case MGSL_IOCSPARAMS:
1149 case MGSL_IOCGTXIDLE:
1150 case MGSL_IOCGSTATS:
1151 case MGSL_IOCWAITEVENT:
1152 case MGSL_IOCGIF:
1153 case MGSL_IOCSGPIO:
1154 case MGSL_IOCGGPIO:
1155 case MGSL_IOCWAITGPIO:
1156 case MGSL_IOCGXSYNC:
1157 case MGSL_IOCGXCTRL:
1158 rc = ioctl(tty, cmd, (unsigned long)compat_ptr(arg));
1159 break;
1160 default:
1161 rc = ioctl(tty, cmd, arg);
1162 }
1163 DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1164 return rc;
1165}
1166#else
1167#define slgt_compat_ioctl NULL
1168#endif /* ifdef CONFIG_COMPAT */
1169
1170/*
1171 * proc fs support
1172 */
1173static inline void line_info(struct seq_file *m, struct slgt_info *info)
1174{
1175 char stat_buf[30];
1176 unsigned long flags;
1177
1178 seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1179 info->device_name, info->phys_reg_addr,
1180 info->irq_level, info->max_frame_size);
1181
1182 /* output current serial signal states */
1183 spin_lock_irqsave(&info->lock,flags);
1184 get_gtsignals(info);
1185 spin_unlock_irqrestore(&info->lock,flags);
1186
1187 stat_buf[0] = 0;
1188 stat_buf[1] = 0;
1189 if (info->signals & SerialSignal_RTS)
1190 strcat(stat_buf, "|RTS");
1191 if (info->signals & SerialSignal_CTS)
1192 strcat(stat_buf, "|CTS");
1193 if (info->signals & SerialSignal_DTR)
1194 strcat(stat_buf, "|DTR");
1195 if (info->signals & SerialSignal_DSR)
1196 strcat(stat_buf, "|DSR");
1197 if (info->signals & SerialSignal_DCD)
1198 strcat(stat_buf, "|CD");
1199 if (info->signals & SerialSignal_RI)
1200 strcat(stat_buf, "|RI");
1201
1202 if (info->params.mode != MGSL_MODE_ASYNC) {
1203 seq_printf(m, "\tHDLC txok:%d rxok:%d",
1204 info->icount.txok, info->icount.rxok);
1205 if (info->icount.txunder)
1206 seq_printf(m, " txunder:%d", info->icount.txunder);
1207 if (info->icount.txabort)
1208 seq_printf(m, " txabort:%d", info->icount.txabort);
1209 if (info->icount.rxshort)
1210 seq_printf(m, " rxshort:%d", info->icount.rxshort);
1211 if (info->icount.rxlong)
1212 seq_printf(m, " rxlong:%d", info->icount.rxlong);
1213 if (info->icount.rxover)
1214 seq_printf(m, " rxover:%d", info->icount.rxover);
1215 if (info->icount.rxcrc)
1216 seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1217 } else {
1218 seq_printf(m, "\tASYNC tx:%d rx:%d",
1219 info->icount.tx, info->icount.rx);
1220 if (info->icount.frame)
1221 seq_printf(m, " fe:%d", info->icount.frame);
1222 if (info->icount.parity)
1223 seq_printf(m, " pe:%d", info->icount.parity);
1224 if (info->icount.brk)
1225 seq_printf(m, " brk:%d", info->icount.brk);
1226 if (info->icount.overrun)
1227 seq_printf(m, " oe:%d", info->icount.overrun);
1228 }
1229
1230 /* Append serial signal status to end */
1231 seq_printf(m, " %s\n", stat_buf+1);
1232
1233 seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1234 info->tx_active,info->bh_requested,info->bh_running,
1235 info->pending_bh);
1236}
1237
1238/* Called to print information about devices
1239 */
1240static int synclink_gt_proc_show(struct seq_file *m, void *v)
1241{
1242 struct slgt_info *info;
1243
1244 seq_puts(m, "synclink_gt driver\n");
1245
1246 info = slgt_device_list;
1247 while( info ) {
1248 line_info(m, info);
1249 info = info->next_device;
1250 }
1251 return 0;
1252}
1253
1254/*
1255 * return count of bytes in transmit buffer
1256 */
1257static unsigned int chars_in_buffer(struct tty_struct *tty)
1258{
1259 struct slgt_info *info = tty->driver_data;
1260 unsigned int count;
1261 if (sanity_check(info, tty->name, "chars_in_buffer"))
1262 return 0;
1263 count = tbuf_bytes(info);
1264 DBGINFO(("%s chars_in_buffer()=%u\n", info->device_name, count));
1265 return count;
1266}
1267
1268/*
1269 * signal remote device to throttle send data (our receive data)
1270 */
1271static void throttle(struct tty_struct * tty)
1272{
1273 struct slgt_info *info = tty->driver_data;
1274 unsigned long flags;
1275
1276 if (sanity_check(info, tty->name, "throttle"))
1277 return;
1278 DBGINFO(("%s throttle\n", info->device_name));
1279 if (I_IXOFF(tty))
1280 send_xchar(tty, STOP_CHAR(tty));
1281 if (C_CRTSCTS(tty)) {
1282 spin_lock_irqsave(&info->lock,flags);
1283 info->signals &= ~SerialSignal_RTS;
1284 set_gtsignals(info);
1285 spin_unlock_irqrestore(&info->lock,flags);
1286 }
1287}
1288
1289/*
1290 * signal remote device to stop throttling send data (our receive data)
1291 */
1292static void unthrottle(struct tty_struct * tty)
1293{
1294 struct slgt_info *info = tty->driver_data;
1295 unsigned long flags;
1296
1297 if (sanity_check(info, tty->name, "unthrottle"))
1298 return;
1299 DBGINFO(("%s unthrottle\n", info->device_name));
1300 if (I_IXOFF(tty)) {
1301 if (info->x_char)
1302 info->x_char = 0;
1303 else
1304 send_xchar(tty, START_CHAR(tty));
1305 }
1306 if (C_CRTSCTS(tty)) {
1307 spin_lock_irqsave(&info->lock,flags);
1308 info->signals |= SerialSignal_RTS;
1309 set_gtsignals(info);
1310 spin_unlock_irqrestore(&info->lock,flags);
1311 }
1312}
1313
1314/*
1315 * set or clear transmit break condition
1316 * break_state -1=set break condition, 0=clear
1317 */
1318static int set_break(struct tty_struct *tty, int break_state)
1319{
1320 struct slgt_info *info = tty->driver_data;
1321 unsigned short value;
1322 unsigned long flags;
1323
1324 if (sanity_check(info, tty->name, "set_break"))
1325 return -EINVAL;
1326 DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1327
1328 spin_lock_irqsave(&info->lock,flags);
1329 value = rd_reg16(info, TCR);
1330 if (break_state == -1)
1331 value |= BIT6;
1332 else
1333 value &= ~BIT6;
1334 wr_reg16(info, TCR, value);
1335 spin_unlock_irqrestore(&info->lock,flags);
1336 return 0;
1337}
1338
1339#if SYNCLINK_GENERIC_HDLC
1340
1341/**
1342 * hdlcdev_attach - called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1343 * @dev: pointer to network device structure
1344 * @encoding: serial encoding setting
1345 * @parity: FCS setting
1346 *
1347 * Set encoding and frame check sequence (FCS) options.
1348 *
1349 * Return: 0 if success, otherwise error code
1350 */
1351static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1352 unsigned short parity)
1353{
1354 struct slgt_info *info = dev_to_port(dev);
1355 unsigned char new_encoding;
1356 unsigned short new_crctype;
1357
1358 /* return error if TTY interface open */
1359 if (info->port.count)
1360 return -EBUSY;
1361
1362 DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1363
1364 switch (encoding)
1365 {
1366 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break;
1367 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1368 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1369 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1370 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1371 default: return -EINVAL;
1372 }
1373
1374 switch (parity)
1375 {
1376 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break;
1377 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1378 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1379 default: return -EINVAL;
1380 }
1381
1382 info->params.encoding = new_encoding;
1383 info->params.crc_type = new_crctype;
1384
1385 /* if network interface up, reprogram hardware */
1386 if (info->netcount)
1387 program_hw(info);
1388
1389 return 0;
1390}
1391
1392/**
1393 * hdlcdev_xmit - called by generic HDLC layer to send a frame
1394 * @skb: socket buffer containing HDLC frame
1395 * @dev: pointer to network device structure
1396 */
1397static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1398 struct net_device *dev)
1399{
1400 struct slgt_info *info = dev_to_port(dev);
1401 unsigned long flags;
1402
1403 DBGINFO(("%s hdlc_xmit\n", dev->name));
1404
1405 if (!skb->len)
1406 return NETDEV_TX_OK;
1407
1408 /* stop sending until this frame completes */
1409 netif_stop_queue(dev);
1410
1411 /* update network statistics */
1412 dev->stats.tx_packets++;
1413 dev->stats.tx_bytes += skb->len;
1414
1415 /* save start time for transmit timeout detection */
1416 netif_trans_update(dev);
1417
1418 spin_lock_irqsave(&info->lock, flags);
1419 tx_load(info, skb->data, skb->len);
1420 spin_unlock_irqrestore(&info->lock, flags);
1421
1422 /* done with socket buffer, so free it */
1423 dev_kfree_skb(skb);
1424
1425 return NETDEV_TX_OK;
1426}
1427
1428/**
1429 * hdlcdev_open - called by network layer when interface enabled
1430 * @dev: pointer to network device structure
1431 *
1432 * Claim resources and initialize hardware.
1433 *
1434 * Return: 0 if success, otherwise error code
1435 */
1436static int hdlcdev_open(struct net_device *dev)
1437{
1438 struct slgt_info *info = dev_to_port(dev);
1439 int rc;
1440 unsigned long flags;
1441
1442 if (!try_module_get(THIS_MODULE))
1443 return -EBUSY;
1444
1445 DBGINFO(("%s hdlcdev_open\n", dev->name));
1446
1447 /* generic HDLC layer open processing */
1448 rc = hdlc_open(dev);
1449 if (rc)
1450 return rc;
1451
1452 /* arbitrate between network and tty opens */
1453 spin_lock_irqsave(&info->netlock, flags);
1454 if (info->port.count != 0 || info->netcount != 0) {
1455 DBGINFO(("%s hdlc_open busy\n", dev->name));
1456 spin_unlock_irqrestore(&info->netlock, flags);
1457 return -EBUSY;
1458 }
1459 info->netcount=1;
1460 spin_unlock_irqrestore(&info->netlock, flags);
1461
1462 /* claim resources and init adapter */
1463 if ((rc = startup(info)) != 0) {
1464 spin_lock_irqsave(&info->netlock, flags);
1465 info->netcount=0;
1466 spin_unlock_irqrestore(&info->netlock, flags);
1467 return rc;
1468 }
1469
1470 /* assert RTS and DTR, apply hardware settings */
1471 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
1472 program_hw(info);
1473
1474 /* enable network layer transmit */
1475 netif_trans_update(dev);
1476 netif_start_queue(dev);
1477
1478 /* inform generic HDLC layer of current DCD status */
1479 spin_lock_irqsave(&info->lock, flags);
1480 get_gtsignals(info);
1481 spin_unlock_irqrestore(&info->lock, flags);
1482 if (info->signals & SerialSignal_DCD)
1483 netif_carrier_on(dev);
1484 else
1485 netif_carrier_off(dev);
1486 return 0;
1487}
1488
1489/**
1490 * hdlcdev_close - called by network layer when interface is disabled
1491 * @dev: pointer to network device structure
1492 *
1493 * Shutdown hardware and release resources.
1494 *
1495 * Return: 0 if success, otherwise error code
1496 */
1497static int hdlcdev_close(struct net_device *dev)
1498{
1499 struct slgt_info *info = dev_to_port(dev);
1500 unsigned long flags;
1501
1502 DBGINFO(("%s hdlcdev_close\n", dev->name));
1503
1504 netif_stop_queue(dev);
1505
1506 /* shutdown adapter and release resources */
1507 shutdown(info);
1508
1509 hdlc_close(dev);
1510
1511 spin_lock_irqsave(&info->netlock, flags);
1512 info->netcount=0;
1513 spin_unlock_irqrestore(&info->netlock, flags);
1514
1515 module_put(THIS_MODULE);
1516 return 0;
1517}
1518
1519/**
1520 * hdlcdev_ioctl - called by network layer to process IOCTL call to network device
1521 * @dev: pointer to network device structure
1522 * @ifr: pointer to network interface request structure
1523 * @cmd: IOCTL command code
1524 *
1525 * Return: 0 if success, otherwise error code
1526 */
1527static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1528{
1529 const size_t size = sizeof(sync_serial_settings);
1530 sync_serial_settings new_line;
1531 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1532 struct slgt_info *info = dev_to_port(dev);
1533 unsigned int flags;
1534
1535 DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1536
1537 /* return error if TTY interface open */
1538 if (info->port.count)
1539 return -EBUSY;
1540
1541 if (cmd != SIOCWANDEV)
1542 return hdlc_ioctl(dev, ifr, cmd);
1543
1544 memset(&new_line, 0, sizeof(new_line));
1545
1546 switch(ifr->ifr_settings.type) {
1547 case IF_GET_IFACE: /* return current sync_serial_settings */
1548
1549 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1550 if (ifr->ifr_settings.size < size) {
1551 ifr->ifr_settings.size = size; /* data size wanted */
1552 return -ENOBUFS;
1553 }
1554
1555 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1556 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1557 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1558 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1559
1560 switch (flags){
1561 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1562 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break;
1563 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break;
1564 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1565 default: new_line.clock_type = CLOCK_DEFAULT;
1566 }
1567
1568 new_line.clock_rate = info->params.clock_speed;
1569 new_line.loopback = info->params.loopback ? 1:0;
1570
1571 if (copy_to_user(line, &new_line, size))
1572 return -EFAULT;
1573 return 0;
1574
1575 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1576
1577 if(!capable(CAP_NET_ADMIN))
1578 return -EPERM;
1579 if (copy_from_user(&new_line, line, size))
1580 return -EFAULT;
1581
1582 switch (new_line.clock_type)
1583 {
1584 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1585 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1586 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break;
1587 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break;
1588 case CLOCK_DEFAULT: flags = info->params.flags &
1589 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1590 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1591 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1592 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break;
1593 default: return -EINVAL;
1594 }
1595
1596 if (new_line.loopback != 0 && new_line.loopback != 1)
1597 return -EINVAL;
1598
1599 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1600 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1601 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1602 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1603 info->params.flags |= flags;
1604
1605 info->params.loopback = new_line.loopback;
1606
1607 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1608 info->params.clock_speed = new_line.clock_rate;
1609 else
1610 info->params.clock_speed = 0;
1611
1612 /* if network interface up, reprogram hardware */
1613 if (info->netcount)
1614 program_hw(info);
1615 return 0;
1616
1617 default:
1618 return hdlc_ioctl(dev, ifr, cmd);
1619 }
1620}
1621
1622/**
1623 * hdlcdev_tx_timeout - called by network layer when transmit timeout is detected
1624 * @dev: pointer to network device structure
1625 * @txqueue: unused
1626 */
1627static void hdlcdev_tx_timeout(struct net_device *dev, unsigned int txqueue)
1628{
1629 struct slgt_info *info = dev_to_port(dev);
1630 unsigned long flags;
1631
1632 DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1633
1634 dev->stats.tx_errors++;
1635 dev->stats.tx_aborted_errors++;
1636
1637 spin_lock_irqsave(&info->lock,flags);
1638 tx_stop(info);
1639 spin_unlock_irqrestore(&info->lock,flags);
1640
1641 netif_wake_queue(dev);
1642}
1643
1644/**
1645 * hdlcdev_tx_done - called by device driver when transmit completes
1646 * @info: pointer to device instance information
1647 *
1648 * Reenable network layer transmit if stopped.
1649 */
1650static void hdlcdev_tx_done(struct slgt_info *info)
1651{
1652 if (netif_queue_stopped(info->netdev))
1653 netif_wake_queue(info->netdev);
1654}
1655
1656/**
1657 * hdlcdev_rx - called by device driver when frame received
1658 * @info: pointer to device instance information
1659 * @buf: pointer to buffer contianing frame data
1660 * @size: count of data bytes in buf
1661 *
1662 * Pass frame to network layer.
1663 */
1664static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1665{
1666 struct sk_buff *skb = dev_alloc_skb(size);
1667 struct net_device *dev = info->netdev;
1668
1669 DBGINFO(("%s hdlcdev_rx\n", dev->name));
1670
1671 if (skb == NULL) {
1672 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1673 dev->stats.rx_dropped++;
1674 return;
1675 }
1676
1677 skb_put_data(skb, buf, size);
1678
1679 skb->protocol = hdlc_type_trans(skb, dev);
1680
1681 dev->stats.rx_packets++;
1682 dev->stats.rx_bytes += size;
1683
1684 netif_rx(skb);
1685}
1686
1687static const struct net_device_ops hdlcdev_ops = {
1688 .ndo_open = hdlcdev_open,
1689 .ndo_stop = hdlcdev_close,
1690 .ndo_start_xmit = hdlc_start_xmit,
1691 .ndo_do_ioctl = hdlcdev_ioctl,
1692 .ndo_tx_timeout = hdlcdev_tx_timeout,
1693};
1694
1695/**
1696 * hdlcdev_init - called by device driver when adding device instance
1697 * @info: pointer to device instance information
1698 *
1699 * Do generic HDLC initialization.
1700 *
1701 * Return: 0 if success, otherwise error code
1702 */
1703static int hdlcdev_init(struct slgt_info *info)
1704{
1705 int rc;
1706 struct net_device *dev;
1707 hdlc_device *hdlc;
1708
1709 /* allocate and initialize network and HDLC layer objects */
1710
1711 dev = alloc_hdlcdev(info);
1712 if (!dev) {
1713 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1714 return -ENOMEM;
1715 }
1716
1717 /* for network layer reporting purposes only */
1718 dev->mem_start = info->phys_reg_addr;
1719 dev->mem_end = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1720 dev->irq = info->irq_level;
1721
1722 /* network layer callbacks and settings */
1723 dev->netdev_ops = &hdlcdev_ops;
1724 dev->watchdog_timeo = 10 * HZ;
1725 dev->tx_queue_len = 50;
1726
1727 /* generic HDLC layer callbacks and settings */
1728 hdlc = dev_to_hdlc(dev);
1729 hdlc->attach = hdlcdev_attach;
1730 hdlc->xmit = hdlcdev_xmit;
1731
1732 /* register objects with HDLC layer */
1733 rc = register_hdlc_device(dev);
1734 if (rc) {
1735 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1736 free_netdev(dev);
1737 return rc;
1738 }
1739
1740 info->netdev = dev;
1741 return 0;
1742}
1743
1744/**
1745 * hdlcdev_exit - called by device driver when removing device instance
1746 * @info: pointer to device instance information
1747 *
1748 * Do generic HDLC cleanup.
1749 */
1750static void hdlcdev_exit(struct slgt_info *info)
1751{
1752 unregister_hdlc_device(info->netdev);
1753 free_netdev(info->netdev);
1754 info->netdev = NULL;
1755}
1756
1757#endif /* ifdef CONFIG_HDLC */
1758
1759/*
1760 * get async data from rx DMA buffers
1761 */
1762static void rx_async(struct slgt_info *info)
1763{
1764 struct mgsl_icount *icount = &info->icount;
1765 unsigned int start, end;
1766 unsigned char *p;
1767 unsigned char status;
1768 struct slgt_desc *bufs = info->rbufs;
1769 int i, count;
1770 int chars = 0;
1771 int stat;
1772 unsigned char ch;
1773
1774 start = end = info->rbuf_current;
1775
1776 while(desc_complete(bufs[end])) {
1777 count = desc_count(bufs[end]) - info->rbuf_index;
1778 p = bufs[end].buf + info->rbuf_index;
1779
1780 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1781 DBGDATA(info, p, count, "rx");
1782
1783 for(i=0 ; i < count; i+=2, p+=2) {
1784 ch = *p;
1785 icount->rx++;
1786
1787 stat = 0;
1788
1789 status = *(p + 1) & (BIT1 + BIT0);
1790 if (status) {
1791 if (status & BIT1)
1792 icount->parity++;
1793 else if (status & BIT0)
1794 icount->frame++;
1795 /* discard char if tty control flags say so */
1796 if (status & info->ignore_status_mask)
1797 continue;
1798 if (status & BIT1)
1799 stat = TTY_PARITY;
1800 else if (status & BIT0)
1801 stat = TTY_FRAME;
1802 }
1803 tty_insert_flip_char(&info->port, ch, stat);
1804 chars++;
1805 }
1806
1807 if (i < count) {
1808 /* receive buffer not completed */
1809 info->rbuf_index += i;
1810 mod_timer(&info->rx_timer, jiffies + 1);
1811 break;
1812 }
1813
1814 info->rbuf_index = 0;
1815 free_rbufs(info, end, end);
1816
1817 if (++end == info->rbuf_count)
1818 end = 0;
1819
1820 /* if entire list searched then no frame available */
1821 if (end == start)
1822 break;
1823 }
1824
1825 if (chars)
1826 tty_flip_buffer_push(&info->port);
1827}
1828
1829/*
1830 * return next bottom half action to perform
1831 */
1832static int bh_action(struct slgt_info *info)
1833{
1834 unsigned long flags;
1835 int rc;
1836
1837 spin_lock_irqsave(&info->lock,flags);
1838
1839 if (info->pending_bh & BH_RECEIVE) {
1840 info->pending_bh &= ~BH_RECEIVE;
1841 rc = BH_RECEIVE;
1842 } else if (info->pending_bh & BH_TRANSMIT) {
1843 info->pending_bh &= ~BH_TRANSMIT;
1844 rc = BH_TRANSMIT;
1845 } else if (info->pending_bh & BH_STATUS) {
1846 info->pending_bh &= ~BH_STATUS;
1847 rc = BH_STATUS;
1848 } else {
1849 /* Mark BH routine as complete */
1850 info->bh_running = false;
1851 info->bh_requested = false;
1852 rc = 0;
1853 }
1854
1855 spin_unlock_irqrestore(&info->lock,flags);
1856
1857 return rc;
1858}
1859
1860/*
1861 * perform bottom half processing
1862 */
1863static void bh_handler(struct work_struct *work)
1864{
1865 struct slgt_info *info = container_of(work, struct slgt_info, task);
1866 int action;
1867
1868 info->bh_running = true;
1869
1870 while((action = bh_action(info))) {
1871 switch (action) {
1872 case BH_RECEIVE:
1873 DBGBH(("%s bh receive\n", info->device_name));
1874 switch(info->params.mode) {
1875 case MGSL_MODE_ASYNC:
1876 rx_async(info);
1877 break;
1878 case MGSL_MODE_HDLC:
1879 while(rx_get_frame(info));
1880 break;
1881 case MGSL_MODE_RAW:
1882 case MGSL_MODE_MONOSYNC:
1883 case MGSL_MODE_BISYNC:
1884 case MGSL_MODE_XSYNC:
1885 while(rx_get_buf(info));
1886 break;
1887 }
1888 /* restart receiver if rx DMA buffers exhausted */
1889 if (info->rx_restart)
1890 rx_start(info);
1891 break;
1892 case BH_TRANSMIT:
1893 bh_transmit(info);
1894 break;
1895 case BH_STATUS:
1896 DBGBH(("%s bh status\n", info->device_name));
1897 info->ri_chkcount = 0;
1898 info->dsr_chkcount = 0;
1899 info->dcd_chkcount = 0;
1900 info->cts_chkcount = 0;
1901 break;
1902 default:
1903 DBGBH(("%s unknown action\n", info->device_name));
1904 break;
1905 }
1906 }
1907 DBGBH(("%s bh_handler exit\n", info->device_name));
1908}
1909
1910static void bh_transmit(struct slgt_info *info)
1911{
1912 struct tty_struct *tty = info->port.tty;
1913
1914 DBGBH(("%s bh_transmit\n", info->device_name));
1915 if (tty)
1916 tty_wakeup(tty);
1917}
1918
1919static void dsr_change(struct slgt_info *info, unsigned short status)
1920{
1921 if (status & BIT3) {
1922 info->signals |= SerialSignal_DSR;
1923 info->input_signal_events.dsr_up++;
1924 } else {
1925 info->signals &= ~SerialSignal_DSR;
1926 info->input_signal_events.dsr_down++;
1927 }
1928 DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1929 if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1930 slgt_irq_off(info, IRQ_DSR);
1931 return;
1932 }
1933 info->icount.dsr++;
1934 wake_up_interruptible(&info->status_event_wait_q);
1935 wake_up_interruptible(&info->event_wait_q);
1936 info->pending_bh |= BH_STATUS;
1937}
1938
1939static void cts_change(struct slgt_info *info, unsigned short status)
1940{
1941 if (status & BIT2) {
1942 info->signals |= SerialSignal_CTS;
1943 info->input_signal_events.cts_up++;
1944 } else {
1945 info->signals &= ~SerialSignal_CTS;
1946 info->input_signal_events.cts_down++;
1947 }
1948 DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
1949 if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1950 slgt_irq_off(info, IRQ_CTS);
1951 return;
1952 }
1953 info->icount.cts++;
1954 wake_up_interruptible(&info->status_event_wait_q);
1955 wake_up_interruptible(&info->event_wait_q);
1956 info->pending_bh |= BH_STATUS;
1957
1958 if (tty_port_cts_enabled(&info->port)) {
1959 if (info->port.tty) {
1960 if (info->port.tty->hw_stopped) {
1961 if (info->signals & SerialSignal_CTS) {
1962 info->port.tty->hw_stopped = 0;
1963 info->pending_bh |= BH_TRANSMIT;
1964 return;
1965 }
1966 } else {
1967 if (!(info->signals & SerialSignal_CTS))
1968 info->port.tty->hw_stopped = 1;
1969 }
1970 }
1971 }
1972}
1973
1974static void dcd_change(struct slgt_info *info, unsigned short status)
1975{
1976 if (status & BIT1) {
1977 info->signals |= SerialSignal_DCD;
1978 info->input_signal_events.dcd_up++;
1979 } else {
1980 info->signals &= ~SerialSignal_DCD;
1981 info->input_signal_events.dcd_down++;
1982 }
1983 DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
1984 if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1985 slgt_irq_off(info, IRQ_DCD);
1986 return;
1987 }
1988 info->icount.dcd++;
1989#if SYNCLINK_GENERIC_HDLC
1990 if (info->netcount) {
1991 if (info->signals & SerialSignal_DCD)
1992 netif_carrier_on(info->netdev);
1993 else
1994 netif_carrier_off(info->netdev);
1995 }
1996#endif
1997 wake_up_interruptible(&info->status_event_wait_q);
1998 wake_up_interruptible(&info->event_wait_q);
1999 info->pending_bh |= BH_STATUS;
2000
2001 if (tty_port_check_carrier(&info->port)) {
2002 if (info->signals & SerialSignal_DCD)
2003 wake_up_interruptible(&info->port.open_wait);
2004 else {
2005 if (info->port.tty)
2006 tty_hangup(info->port.tty);
2007 }
2008 }
2009}
2010
2011static void ri_change(struct slgt_info *info, unsigned short status)
2012{
2013 if (status & BIT0) {
2014 info->signals |= SerialSignal_RI;
2015 info->input_signal_events.ri_up++;
2016 } else {
2017 info->signals &= ~SerialSignal_RI;
2018 info->input_signal_events.ri_down++;
2019 }
2020 DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2021 if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2022 slgt_irq_off(info, IRQ_RI);
2023 return;
2024 }
2025 info->icount.rng++;
2026 wake_up_interruptible(&info->status_event_wait_q);
2027 wake_up_interruptible(&info->event_wait_q);
2028 info->pending_bh |= BH_STATUS;
2029}
2030
2031static void isr_rxdata(struct slgt_info *info)
2032{
2033 unsigned int count = info->rbuf_fill_count;
2034 unsigned int i = info->rbuf_fill_index;
2035 unsigned short reg;
2036
2037 while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2038 reg = rd_reg16(info, RDR);
2039 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2040 if (desc_complete(info->rbufs[i])) {
2041 /* all buffers full */
2042 rx_stop(info);
2043 info->rx_restart = true;
2044 continue;
2045 }
2046 info->rbufs[i].buf[count++] = (unsigned char)reg;
2047 /* async mode saves status byte to buffer for each data byte */
2048 if (info->params.mode == MGSL_MODE_ASYNC)
2049 info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2050 if (count == info->rbuf_fill_level || (reg & BIT10)) {
2051 /* buffer full or end of frame */
2052 set_desc_count(info->rbufs[i], count);
2053 set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2054 info->rbuf_fill_count = count = 0;
2055 if (++i == info->rbuf_count)
2056 i = 0;
2057 info->pending_bh |= BH_RECEIVE;
2058 }
2059 }
2060
2061 info->rbuf_fill_index = i;
2062 info->rbuf_fill_count = count;
2063}
2064
2065static void isr_serial(struct slgt_info *info)
2066{
2067 unsigned short status = rd_reg16(info, SSR);
2068
2069 DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2070
2071 wr_reg16(info, SSR, status); /* clear pending */
2072
2073 info->irq_occurred = true;
2074
2075 if (info->params.mode == MGSL_MODE_ASYNC) {
2076 if (status & IRQ_TXIDLE) {
2077 if (info->tx_active)
2078 isr_txeom(info, status);
2079 }
2080 if (info->rx_pio && (status & IRQ_RXDATA))
2081 isr_rxdata(info);
2082 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2083 info->icount.brk++;
2084 /* process break detection if tty control allows */
2085 if (info->port.tty) {
2086 if (!(status & info->ignore_status_mask)) {
2087 if (info->read_status_mask & MASK_BREAK) {
2088 tty_insert_flip_char(&info->port, 0, TTY_BREAK);
2089 if (info->port.flags & ASYNC_SAK)
2090 do_SAK(info->port.tty);
2091 }
2092 }
2093 }
2094 }
2095 } else {
2096 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2097 isr_txeom(info, status);
2098 if (info->rx_pio && (status & IRQ_RXDATA))
2099 isr_rxdata(info);
2100 if (status & IRQ_RXIDLE) {
2101 if (status & RXIDLE)
2102 info->icount.rxidle++;
2103 else
2104 info->icount.exithunt++;
2105 wake_up_interruptible(&info->event_wait_q);
2106 }
2107
2108 if (status & IRQ_RXOVER)
2109 rx_start(info);
2110 }
2111
2112 if (status & IRQ_DSR)
2113 dsr_change(info, status);
2114 if (status & IRQ_CTS)
2115 cts_change(info, status);
2116 if (status & IRQ_DCD)
2117 dcd_change(info, status);
2118 if (status & IRQ_RI)
2119 ri_change(info, status);
2120}
2121
2122static void isr_rdma(struct slgt_info *info)
2123{
2124 unsigned int status = rd_reg32(info, RDCSR);
2125
2126 DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2127
2128 /* RDCSR (rx DMA control/status)
2129 *
2130 * 31..07 reserved
2131 * 06 save status byte to DMA buffer
2132 * 05 error
2133 * 04 eol (end of list)
2134 * 03 eob (end of buffer)
2135 * 02 IRQ enable
2136 * 01 reset
2137 * 00 enable
2138 */
2139 wr_reg32(info, RDCSR, status); /* clear pending */
2140
2141 if (status & (BIT5 + BIT4)) {
2142 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2143 info->rx_restart = true;
2144 }
2145 info->pending_bh |= BH_RECEIVE;
2146}
2147
2148static void isr_tdma(struct slgt_info *info)
2149{
2150 unsigned int status = rd_reg32(info, TDCSR);
2151
2152 DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2153
2154 /* TDCSR (tx DMA control/status)
2155 *
2156 * 31..06 reserved
2157 * 05 error
2158 * 04 eol (end of list)
2159 * 03 eob (end of buffer)
2160 * 02 IRQ enable
2161 * 01 reset
2162 * 00 enable
2163 */
2164 wr_reg32(info, TDCSR, status); /* clear pending */
2165
2166 if (status & (BIT5 + BIT4 + BIT3)) {
2167 // another transmit buffer has completed
2168 // run bottom half to get more send data from user
2169 info->pending_bh |= BH_TRANSMIT;
2170 }
2171}
2172
2173/*
2174 * return true if there are unsent tx DMA buffers, otherwise false
2175 *
2176 * if there are unsent buffers then info->tbuf_start
2177 * is set to index of first unsent buffer
2178 */
2179static bool unsent_tbufs(struct slgt_info *info)
2180{
2181 unsigned int i = info->tbuf_current;
2182 bool rc = false;
2183
2184 /*
2185 * search backwards from last loaded buffer (precedes tbuf_current)
2186 * for first unsent buffer (desc_count > 0)
2187 */
2188
2189 do {
2190 if (i)
2191 i--;
2192 else
2193 i = info->tbuf_count - 1;
2194 if (!desc_count(info->tbufs[i]))
2195 break;
2196 info->tbuf_start = i;
2197 rc = true;
2198 } while (i != info->tbuf_current);
2199
2200 return rc;
2201}
2202
2203static void isr_txeom(struct slgt_info *info, unsigned short status)
2204{
2205 DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2206
2207 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2208 tdma_reset(info);
2209 if (status & IRQ_TXUNDER) {
2210 unsigned short val = rd_reg16(info, TCR);
2211 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2212 wr_reg16(info, TCR, val); /* clear reset bit */
2213 }
2214
2215 if (info->tx_active) {
2216 if (info->params.mode != MGSL_MODE_ASYNC) {
2217 if (status & IRQ_TXUNDER)
2218 info->icount.txunder++;
2219 else if (status & IRQ_TXIDLE)
2220 info->icount.txok++;
2221 }
2222
2223 if (unsent_tbufs(info)) {
2224 tx_start(info);
2225 update_tx_timer(info);
2226 return;
2227 }
2228 info->tx_active = false;
2229
2230 del_timer(&info->tx_timer);
2231
2232 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2233 info->signals &= ~SerialSignal_RTS;
2234 info->drop_rts_on_tx_done = false;
2235 set_gtsignals(info);
2236 }
2237
2238#if SYNCLINK_GENERIC_HDLC
2239 if (info->netcount)
2240 hdlcdev_tx_done(info);
2241 else
2242#endif
2243 {
2244 if (info->port.tty && (info->port.tty->flow.stopped || info->port.tty->hw_stopped)) {
2245 tx_stop(info);
2246 return;
2247 }
2248 info->pending_bh |= BH_TRANSMIT;
2249 }
2250 }
2251}
2252
2253static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2254{
2255 struct cond_wait *w, *prev;
2256
2257 /* wake processes waiting for specific transitions */
2258 for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2259 if (w->data & changed) {
2260 w->data = state;
2261 wake_up_interruptible(&w->q);
2262 if (prev != NULL)
2263 prev->next = w->next;
2264 else
2265 info->gpio_wait_q = w->next;
2266 } else
2267 prev = w;
2268 }
2269}
2270
2271/* interrupt service routine
2272 *
2273 * irq interrupt number
2274 * dev_id device ID supplied during interrupt registration
2275 */
2276static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2277{
2278 struct slgt_info *info = dev_id;
2279 unsigned int gsr;
2280 unsigned int i;
2281
2282 DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2283
2284 while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2285 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2286 info->irq_occurred = true;
2287 for(i=0; i < info->port_count ; i++) {
2288 if (info->port_array[i] == NULL)
2289 continue;
2290 spin_lock(&info->port_array[i]->lock);
2291 if (gsr & (BIT8 << i))
2292 isr_serial(info->port_array[i]);
2293 if (gsr & (BIT16 << (i*2)))
2294 isr_rdma(info->port_array[i]);
2295 if (gsr & (BIT17 << (i*2)))
2296 isr_tdma(info->port_array[i]);
2297 spin_unlock(&info->port_array[i]->lock);
2298 }
2299 }
2300
2301 if (info->gpio_present) {
2302 unsigned int state;
2303 unsigned int changed;
2304 spin_lock(&info->lock);
2305 while ((changed = rd_reg32(info, IOSR)) != 0) {
2306 DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2307 /* read latched state of GPIO signals */
2308 state = rd_reg32(info, IOVR);
2309 /* clear pending GPIO interrupt bits */
2310 wr_reg32(info, IOSR, changed);
2311 for (i=0 ; i < info->port_count ; i++) {
2312 if (info->port_array[i] != NULL)
2313 isr_gpio(info->port_array[i], changed, state);
2314 }
2315 }
2316 spin_unlock(&info->lock);
2317 }
2318
2319 for(i=0; i < info->port_count ; i++) {
2320 struct slgt_info *port = info->port_array[i];
2321 if (port == NULL)
2322 continue;
2323 spin_lock(&port->lock);
2324 if ((port->port.count || port->netcount) &&
2325 port->pending_bh && !port->bh_running &&
2326 !port->bh_requested) {
2327 DBGISR(("%s bh queued\n", port->device_name));
2328 schedule_work(&port->task);
2329 port->bh_requested = true;
2330 }
2331 spin_unlock(&port->lock);
2332 }
2333
2334 DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2335 return IRQ_HANDLED;
2336}
2337
2338static int startup(struct slgt_info *info)
2339{
2340 DBGINFO(("%s startup\n", info->device_name));
2341
2342 if (tty_port_initialized(&info->port))
2343 return 0;
2344
2345 if (!info->tx_buf) {
2346 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2347 if (!info->tx_buf) {
2348 DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2349 return -ENOMEM;
2350 }
2351 }
2352
2353 info->pending_bh = 0;
2354
2355 memset(&info->icount, 0, sizeof(info->icount));
2356
2357 /* program hardware for current parameters */
2358 change_params(info);
2359
2360 if (info->port.tty)
2361 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2362
2363 tty_port_set_initialized(&info->port, 1);
2364
2365 return 0;
2366}
2367
2368/*
2369 * called by close() and hangup() to shutdown hardware
2370 */
2371static void shutdown(struct slgt_info *info)
2372{
2373 unsigned long flags;
2374
2375 if (!tty_port_initialized(&info->port))
2376 return;
2377
2378 DBGINFO(("%s shutdown\n", info->device_name));
2379
2380 /* clear status wait queue because status changes */
2381 /* can't happen after shutting down the hardware */
2382 wake_up_interruptible(&info->status_event_wait_q);
2383 wake_up_interruptible(&info->event_wait_q);
2384
2385 del_timer_sync(&info->tx_timer);
2386 del_timer_sync(&info->rx_timer);
2387
2388 kfree(info->tx_buf);
2389 info->tx_buf = NULL;
2390
2391 spin_lock_irqsave(&info->lock,flags);
2392
2393 tx_stop(info);
2394 rx_stop(info);
2395
2396 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2397
2398 if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
2399 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2400 set_gtsignals(info);
2401 }
2402
2403 flush_cond_wait(&info->gpio_wait_q);
2404
2405 spin_unlock_irqrestore(&info->lock,flags);
2406
2407 if (info->port.tty)
2408 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2409
2410 tty_port_set_initialized(&info->port, 0);
2411}
2412
2413static void program_hw(struct slgt_info *info)
2414{
2415 unsigned long flags;
2416
2417 spin_lock_irqsave(&info->lock,flags);
2418
2419 rx_stop(info);
2420 tx_stop(info);
2421
2422 if (info->params.mode != MGSL_MODE_ASYNC ||
2423 info->netcount)
2424 sync_mode(info);
2425 else
2426 async_mode(info);
2427
2428 set_gtsignals(info);
2429
2430 info->dcd_chkcount = 0;
2431 info->cts_chkcount = 0;
2432 info->ri_chkcount = 0;
2433 info->dsr_chkcount = 0;
2434
2435 slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2436 get_gtsignals(info);
2437
2438 if (info->netcount ||
2439 (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
2440 rx_start(info);
2441
2442 spin_unlock_irqrestore(&info->lock,flags);
2443}
2444
2445/*
2446 * reconfigure adapter based on new parameters
2447 */
2448static void change_params(struct slgt_info *info)
2449{
2450 unsigned cflag;
2451 int bits_per_char;
2452
2453 if (!info->port.tty)
2454 return;
2455 DBGINFO(("%s change_params\n", info->device_name));
2456
2457 cflag = info->port.tty->termios.c_cflag;
2458
2459 /* if B0 rate (hangup) specified then negate RTS and DTR */
2460 /* otherwise assert RTS and DTR */
2461 if (cflag & CBAUD)
2462 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
2463 else
2464 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2465
2466 /* byte size and parity */
2467
2468 info->params.data_bits = tty_get_char_size(cflag);
2469 info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2470
2471 if (cflag & PARENB)
2472 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2473 else
2474 info->params.parity = ASYNC_PARITY_NONE;
2475
2476 /* calculate number of jiffies to transmit a full
2477 * FIFO (32 bytes) at specified data rate
2478 */
2479 bits_per_char = info->params.data_bits +
2480 info->params.stop_bits + 1;
2481
2482 info->params.data_rate = tty_get_baud_rate(info->port.tty);
2483
2484 if (info->params.data_rate) {
2485 info->timeout = (32*HZ*bits_per_char) /
2486 info->params.data_rate;
2487 }
2488 info->timeout += HZ/50; /* Add .02 seconds of slop */
2489
2490 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
2491 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
2492
2493 /* process tty input control flags */
2494
2495 info->read_status_mask = IRQ_RXOVER;
2496 if (I_INPCK(info->port.tty))
2497 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2498 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2499 info->read_status_mask |= MASK_BREAK;
2500 if (I_IGNPAR(info->port.tty))
2501 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2502 if (I_IGNBRK(info->port.tty)) {
2503 info->ignore_status_mask |= MASK_BREAK;
2504 /* If ignoring parity and break indicators, ignore
2505 * overruns too. (For real raw support).
2506 */
2507 if (I_IGNPAR(info->port.tty))
2508 info->ignore_status_mask |= MASK_OVERRUN;
2509 }
2510
2511 program_hw(info);
2512}
2513
2514static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2515{
2516 DBGINFO(("%s get_stats\n", info->device_name));
2517 if (!user_icount) {
2518 memset(&info->icount, 0, sizeof(info->icount));
2519 } else {
2520 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2521 return -EFAULT;
2522 }
2523 return 0;
2524}
2525
2526static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2527{
2528 DBGINFO(("%s get_params\n", info->device_name));
2529 if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2530 return -EFAULT;
2531 return 0;
2532}
2533
2534static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2535{
2536 unsigned long flags;
2537 MGSL_PARAMS tmp_params;
2538
2539 DBGINFO(("%s set_params\n", info->device_name));
2540 if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2541 return -EFAULT;
2542
2543 spin_lock_irqsave(&info->lock, flags);
2544 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2545 info->base_clock = tmp_params.clock_speed;
2546 else
2547 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2548 spin_unlock_irqrestore(&info->lock, flags);
2549
2550 program_hw(info);
2551
2552 return 0;
2553}
2554
2555static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2556{
2557 DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2558 if (put_user(info->idle_mode, idle_mode))
2559 return -EFAULT;
2560 return 0;
2561}
2562
2563static int set_txidle(struct slgt_info *info, int idle_mode)
2564{
2565 unsigned long flags;
2566 DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2567 spin_lock_irqsave(&info->lock,flags);
2568 info->idle_mode = idle_mode;
2569 if (info->params.mode != MGSL_MODE_ASYNC)
2570 tx_set_idle(info);
2571 spin_unlock_irqrestore(&info->lock,flags);
2572 return 0;
2573}
2574
2575static int tx_enable(struct slgt_info *info, int enable)
2576{
2577 unsigned long flags;
2578 DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2579 spin_lock_irqsave(&info->lock,flags);
2580 if (enable) {
2581 if (!info->tx_enabled)
2582 tx_start(info);
2583 } else {
2584 if (info->tx_enabled)
2585 tx_stop(info);
2586 }
2587 spin_unlock_irqrestore(&info->lock,flags);
2588 return 0;
2589}
2590
2591/*
2592 * abort transmit HDLC frame
2593 */
2594static int tx_abort(struct slgt_info *info)
2595{
2596 unsigned long flags;
2597 DBGINFO(("%s tx_abort\n", info->device_name));
2598 spin_lock_irqsave(&info->lock,flags);
2599 tdma_reset(info);
2600 spin_unlock_irqrestore(&info->lock,flags);
2601 return 0;
2602}
2603
2604static int rx_enable(struct slgt_info *info, int enable)
2605{
2606 unsigned long flags;
2607 unsigned int rbuf_fill_level;
2608 DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2609 spin_lock_irqsave(&info->lock,flags);
2610 /*
2611 * enable[31..16] = receive DMA buffer fill level
2612 * 0 = noop (leave fill level unchanged)
2613 * fill level must be multiple of 4 and <= buffer size
2614 */
2615 rbuf_fill_level = ((unsigned int)enable) >> 16;
2616 if (rbuf_fill_level) {
2617 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2618 spin_unlock_irqrestore(&info->lock, flags);
2619 return -EINVAL;
2620 }
2621 info->rbuf_fill_level = rbuf_fill_level;
2622 if (rbuf_fill_level < 128)
2623 info->rx_pio = 1; /* PIO mode */
2624 else
2625 info->rx_pio = 0; /* DMA mode */
2626 rx_stop(info); /* restart receiver to use new fill level */
2627 }
2628
2629 /*
2630 * enable[1..0] = receiver enable command
2631 * 0 = disable
2632 * 1 = enable
2633 * 2 = enable or force hunt mode if already enabled
2634 */
2635 enable &= 3;
2636 if (enable) {
2637 if (!info->rx_enabled)
2638 rx_start(info);
2639 else if (enable == 2) {
2640 /* force hunt mode (write 1 to RCR[3]) */
2641 wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2642 }
2643 } else {
2644 if (info->rx_enabled)
2645 rx_stop(info);
2646 }
2647 spin_unlock_irqrestore(&info->lock,flags);
2648 return 0;
2649}
2650
2651/*
2652 * wait for specified event to occur
2653 */
2654static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2655{
2656 unsigned long flags;
2657 int s;
2658 int rc=0;
2659 struct mgsl_icount cprev, cnow;
2660 int events;
2661 int mask;
2662 struct _input_signal_events oldsigs, newsigs;
2663 DECLARE_WAITQUEUE(wait, current);
2664
2665 if (get_user(mask, mask_ptr))
2666 return -EFAULT;
2667
2668 DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2669
2670 spin_lock_irqsave(&info->lock,flags);
2671
2672 /* return immediately if state matches requested events */
2673 get_gtsignals(info);
2674 s = info->signals;
2675
2676 events = mask &
2677 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2678 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2679 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2680 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2681 if (events) {
2682 spin_unlock_irqrestore(&info->lock,flags);
2683 goto exit;
2684 }
2685
2686 /* save current irq counts */
2687 cprev = info->icount;
2688 oldsigs = info->input_signal_events;
2689
2690 /* enable hunt and idle irqs if needed */
2691 if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2692 unsigned short val = rd_reg16(info, SCR);
2693 if (!(val & IRQ_RXIDLE))
2694 wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2695 }
2696
2697 set_current_state(TASK_INTERRUPTIBLE);
2698 add_wait_queue(&info->event_wait_q, &wait);
2699
2700 spin_unlock_irqrestore(&info->lock,flags);
2701
2702 for(;;) {
2703 schedule();
2704 if (signal_pending(current)) {
2705 rc = -ERESTARTSYS;
2706 break;
2707 }
2708
2709 /* get current irq counts */
2710 spin_lock_irqsave(&info->lock,flags);
2711 cnow = info->icount;
2712 newsigs = info->input_signal_events;
2713 set_current_state(TASK_INTERRUPTIBLE);
2714 spin_unlock_irqrestore(&info->lock,flags);
2715
2716 /* if no change, wait aborted for some reason */
2717 if (newsigs.dsr_up == oldsigs.dsr_up &&
2718 newsigs.dsr_down == oldsigs.dsr_down &&
2719 newsigs.dcd_up == oldsigs.dcd_up &&
2720 newsigs.dcd_down == oldsigs.dcd_down &&
2721 newsigs.cts_up == oldsigs.cts_up &&
2722 newsigs.cts_down == oldsigs.cts_down &&
2723 newsigs.ri_up == oldsigs.ri_up &&
2724 newsigs.ri_down == oldsigs.ri_down &&
2725 cnow.exithunt == cprev.exithunt &&
2726 cnow.rxidle == cprev.rxidle) {
2727 rc = -EIO;
2728 break;
2729 }
2730
2731 events = mask &
2732 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) +
2733 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2734 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) +
2735 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2736 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) +
2737 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2738 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) +
2739 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) +
2740 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) +
2741 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) );
2742 if (events)
2743 break;
2744
2745 cprev = cnow;
2746 oldsigs = newsigs;
2747 }
2748
2749 remove_wait_queue(&info->event_wait_q, &wait);
2750 set_current_state(TASK_RUNNING);
2751
2752
2753 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2754 spin_lock_irqsave(&info->lock,flags);
2755 if (!waitqueue_active(&info->event_wait_q)) {
2756 /* disable enable exit hunt mode/idle rcvd IRQs */
2757 wr_reg16(info, SCR,
2758 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2759 }
2760 spin_unlock_irqrestore(&info->lock,flags);
2761 }
2762exit:
2763 if (rc == 0)
2764 rc = put_user(events, mask_ptr);
2765 return rc;
2766}
2767
2768static int get_interface(struct slgt_info *info, int __user *if_mode)
2769{
2770 DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2771 if (put_user(info->if_mode, if_mode))
2772 return -EFAULT;
2773 return 0;
2774}
2775
2776static int set_interface(struct slgt_info *info, int if_mode)
2777{
2778 unsigned long flags;
2779 unsigned short val;
2780
2781 DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2782 spin_lock_irqsave(&info->lock,flags);
2783 info->if_mode = if_mode;
2784
2785 msc_set_vcr(info);
2786
2787 /* TCR (tx control) 07 1=RTS driver control */
2788 val = rd_reg16(info, TCR);
2789 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2790 val |= BIT7;
2791 else
2792 val &= ~BIT7;
2793 wr_reg16(info, TCR, val);
2794
2795 spin_unlock_irqrestore(&info->lock,flags);
2796 return 0;
2797}
2798
2799static int get_xsync(struct slgt_info *info, int __user *xsync)
2800{
2801 DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2802 if (put_user(info->xsync, xsync))
2803 return -EFAULT;
2804 return 0;
2805}
2806
2807/*
2808 * set extended sync pattern (1 to 4 bytes) for extended sync mode
2809 *
2810 * sync pattern is contained in least significant bytes of value
2811 * most significant byte of sync pattern is oldest (1st sent/detected)
2812 */
2813static int set_xsync(struct slgt_info *info, int xsync)
2814{
2815 unsigned long flags;
2816
2817 DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2818 spin_lock_irqsave(&info->lock, flags);
2819 info->xsync = xsync;
2820 wr_reg32(info, XSR, xsync);
2821 spin_unlock_irqrestore(&info->lock, flags);
2822 return 0;
2823}
2824
2825static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2826{
2827 DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2828 if (put_user(info->xctrl, xctrl))
2829 return -EFAULT;
2830 return 0;
2831}
2832
2833/*
2834 * set extended control options
2835 *
2836 * xctrl[31:19] reserved, must be zero
2837 * xctrl[18:17] extended sync pattern length in bytes
2838 * 00 = 1 byte in xsr[7:0]
2839 * 01 = 2 bytes in xsr[15:0]
2840 * 10 = 3 bytes in xsr[23:0]
2841 * 11 = 4 bytes in xsr[31:0]
2842 * xctrl[16] 1 = enable terminal count, 0=disabled
2843 * xctrl[15:0] receive terminal count for fixed length packets
2844 * value is count minus one (0 = 1 byte packet)
2845 * when terminal count is reached, receiver
2846 * automatically returns to hunt mode and receive
2847 * FIFO contents are flushed to DMA buffers with
2848 * end of frame (EOF) status
2849 */
2850static int set_xctrl(struct slgt_info *info, int xctrl)
2851{
2852 unsigned long flags;
2853
2854 DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2855 spin_lock_irqsave(&info->lock, flags);
2856 info->xctrl = xctrl;
2857 wr_reg32(info, XCR, xctrl);
2858 spin_unlock_irqrestore(&info->lock, flags);
2859 return 0;
2860}
2861
2862/*
2863 * set general purpose IO pin state and direction
2864 *
2865 * user_gpio fields:
2866 * state each bit indicates a pin state
2867 * smask set bit indicates pin state to set
2868 * dir each bit indicates a pin direction (0=input, 1=output)
2869 * dmask set bit indicates pin direction to set
2870 */
2871static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2872{
2873 unsigned long flags;
2874 struct gpio_desc gpio;
2875 __u32 data;
2876
2877 if (!info->gpio_present)
2878 return -EINVAL;
2879 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2880 return -EFAULT;
2881 DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2882 info->device_name, gpio.state, gpio.smask,
2883 gpio.dir, gpio.dmask));
2884
2885 spin_lock_irqsave(&info->port_array[0]->lock, flags);
2886 if (gpio.dmask) {
2887 data = rd_reg32(info, IODR);
2888 data |= gpio.dmask & gpio.dir;
2889 data &= ~(gpio.dmask & ~gpio.dir);
2890 wr_reg32(info, IODR, data);
2891 }
2892 if (gpio.smask) {
2893 data = rd_reg32(info, IOVR);
2894 data |= gpio.smask & gpio.state;
2895 data &= ~(gpio.smask & ~gpio.state);
2896 wr_reg32(info, IOVR, data);
2897 }
2898 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
2899
2900 return 0;
2901}
2902
2903/*
2904 * get general purpose IO pin state and direction
2905 */
2906static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2907{
2908 struct gpio_desc gpio;
2909 if (!info->gpio_present)
2910 return -EINVAL;
2911 gpio.state = rd_reg32(info, IOVR);
2912 gpio.smask = 0xffffffff;
2913 gpio.dir = rd_reg32(info, IODR);
2914 gpio.dmask = 0xffffffff;
2915 if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2916 return -EFAULT;
2917 DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2918 info->device_name, gpio.state, gpio.dir));
2919 return 0;
2920}
2921
2922/*
2923 * conditional wait facility
2924 */
2925static void init_cond_wait(struct cond_wait *w, unsigned int data)
2926{
2927 init_waitqueue_head(&w->q);
2928 init_waitqueue_entry(&w->wait, current);
2929 w->data = data;
2930}
2931
2932static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2933{
2934 set_current_state(TASK_INTERRUPTIBLE);
2935 add_wait_queue(&w->q, &w->wait);
2936 w->next = *head;
2937 *head = w;
2938}
2939
2940static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2941{
2942 struct cond_wait *w, *prev;
2943 remove_wait_queue(&cw->q, &cw->wait);
2944 set_current_state(TASK_RUNNING);
2945 for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2946 if (w == cw) {
2947 if (prev != NULL)
2948 prev->next = w->next;
2949 else
2950 *head = w->next;
2951 break;
2952 }
2953 }
2954}
2955
2956static void flush_cond_wait(struct cond_wait **head)
2957{
2958 while (*head != NULL) {
2959 wake_up_interruptible(&(*head)->q);
2960 *head = (*head)->next;
2961 }
2962}
2963
2964/*
2965 * wait for general purpose I/O pin(s) to enter specified state
2966 *
2967 * user_gpio fields:
2968 * state - bit indicates target pin state
2969 * smask - set bit indicates watched pin
2970 *
2971 * The wait ends when at least one watched pin enters the specified
2972 * state. When 0 (no error) is returned, user_gpio->state is set to the
2973 * state of all GPIO pins when the wait ends.
2974 *
2975 * Note: Each pin may be a dedicated input, dedicated output, or
2976 * configurable input/output. The number and configuration of pins
2977 * varies with the specific adapter model. Only input pins (dedicated
2978 * or configured) can be monitored with this function.
2979 */
2980static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2981{
2982 unsigned long flags;
2983 int rc = 0;
2984 struct gpio_desc gpio;
2985 struct cond_wait wait;
2986 u32 state;
2987
2988 if (!info->gpio_present)
2989 return -EINVAL;
2990 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2991 return -EFAULT;
2992 DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2993 info->device_name, gpio.state, gpio.smask));
2994 /* ignore output pins identified by set IODR bit */
2995 if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2996 return -EINVAL;
2997 init_cond_wait(&wait, gpio.smask);
2998
2999 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3000 /* enable interrupts for watched pins */
3001 wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3002 /* get current pin states */
3003 state = rd_reg32(info, IOVR);
3004
3005 if (gpio.smask & ~(state ^ gpio.state)) {
3006 /* already in target state */
3007 gpio.state = state;
3008 } else {
3009 /* wait for target state */
3010 add_cond_wait(&info->gpio_wait_q, &wait);
3011 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3012 schedule();
3013 if (signal_pending(current))
3014 rc = -ERESTARTSYS;
3015 else
3016 gpio.state = wait.data;
3017 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3018 remove_cond_wait(&info->gpio_wait_q, &wait);
3019 }
3020
3021 /* disable all GPIO interrupts if no waiting processes */
3022 if (info->gpio_wait_q == NULL)
3023 wr_reg32(info, IOER, 0);
3024 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3025
3026 if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3027 rc = -EFAULT;
3028 return rc;
3029}
3030
3031static int modem_input_wait(struct slgt_info *info,int arg)
3032{
3033 unsigned long flags;
3034 int rc;
3035 struct mgsl_icount cprev, cnow;
3036 DECLARE_WAITQUEUE(wait, current);
3037
3038 /* save current irq counts */
3039 spin_lock_irqsave(&info->lock,flags);
3040 cprev = info->icount;
3041 add_wait_queue(&info->status_event_wait_q, &wait);
3042 set_current_state(TASK_INTERRUPTIBLE);
3043 spin_unlock_irqrestore(&info->lock,flags);
3044
3045 for(;;) {
3046 schedule();
3047 if (signal_pending(current)) {
3048 rc = -ERESTARTSYS;
3049 break;
3050 }
3051
3052 /* get new irq counts */
3053 spin_lock_irqsave(&info->lock,flags);
3054 cnow = info->icount;
3055 set_current_state(TASK_INTERRUPTIBLE);
3056 spin_unlock_irqrestore(&info->lock,flags);
3057
3058 /* if no change, wait aborted for some reason */
3059 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3060 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3061 rc = -EIO;
3062 break;
3063 }
3064
3065 /* check for change in caller specified modem input */
3066 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3067 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3068 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) ||
3069 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3070 rc = 0;
3071 break;
3072 }
3073
3074 cprev = cnow;
3075 }
3076 remove_wait_queue(&info->status_event_wait_q, &wait);
3077 set_current_state(TASK_RUNNING);
3078 return rc;
3079}
3080
3081/*
3082 * return state of serial control and status signals
3083 */
3084static int tiocmget(struct tty_struct *tty)
3085{
3086 struct slgt_info *info = tty->driver_data;
3087 unsigned int result;
3088 unsigned long flags;
3089
3090 spin_lock_irqsave(&info->lock,flags);
3091 get_gtsignals(info);
3092 spin_unlock_irqrestore(&info->lock,flags);
3093
3094 result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3095 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3096 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3097 ((info->signals & SerialSignal_RI) ? TIOCM_RNG:0) +
3098 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3099 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3100
3101 DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3102 return result;
3103}
3104
3105/*
3106 * set modem control signals (DTR/RTS)
3107 *
3108 * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3109 * TIOCMSET = set/clear signal values
3110 * value bit mask for command
3111 */
3112static int tiocmset(struct tty_struct *tty,
3113 unsigned int set, unsigned int clear)
3114{
3115 struct slgt_info *info = tty->driver_data;
3116 unsigned long flags;
3117
3118 DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3119
3120 if (set & TIOCM_RTS)
3121 info->signals |= SerialSignal_RTS;
3122 if (set & TIOCM_DTR)
3123 info->signals |= SerialSignal_DTR;
3124 if (clear & TIOCM_RTS)
3125 info->signals &= ~SerialSignal_RTS;
3126 if (clear & TIOCM_DTR)
3127 info->signals &= ~SerialSignal_DTR;
3128
3129 spin_lock_irqsave(&info->lock,flags);
3130 set_gtsignals(info);
3131 spin_unlock_irqrestore(&info->lock,flags);
3132 return 0;
3133}
3134
3135static int carrier_raised(struct tty_port *port)
3136{
3137 unsigned long flags;
3138 struct slgt_info *info = container_of(port, struct slgt_info, port);
3139
3140 spin_lock_irqsave(&info->lock,flags);
3141 get_gtsignals(info);
3142 spin_unlock_irqrestore(&info->lock,flags);
3143 return (info->signals & SerialSignal_DCD) ? 1 : 0;
3144}
3145
3146static void dtr_rts(struct tty_port *port, int on)
3147{
3148 unsigned long flags;
3149 struct slgt_info *info = container_of(port, struct slgt_info, port);
3150
3151 spin_lock_irqsave(&info->lock,flags);
3152 if (on)
3153 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
3154 else
3155 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3156 set_gtsignals(info);
3157 spin_unlock_irqrestore(&info->lock,flags);
3158}
3159
3160
3161/*
3162 * block current process until the device is ready to open
3163 */
3164static int block_til_ready(struct tty_struct *tty, struct file *filp,
3165 struct slgt_info *info)
3166{
3167 DECLARE_WAITQUEUE(wait, current);
3168 int retval;
3169 bool do_clocal = false;
3170 unsigned long flags;
3171 int cd;
3172 struct tty_port *port = &info->port;
3173
3174 DBGINFO(("%s block_til_ready\n", tty->driver->name));
3175
3176 if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
3177 /* nonblock mode is set or port is not enabled */
3178 tty_port_set_active(port, 1);
3179 return 0;
3180 }
3181
3182 if (C_CLOCAL(tty))
3183 do_clocal = true;
3184
3185 /* Wait for carrier detect and the line to become
3186 * free (i.e., not in use by the callout). While we are in
3187 * this loop, port->count is dropped by one, so that
3188 * close() knows when to free things. We restore it upon
3189 * exit, either normal or abnormal.
3190 */
3191
3192 retval = 0;
3193 add_wait_queue(&port->open_wait, &wait);
3194
3195 spin_lock_irqsave(&info->lock, flags);
3196 port->count--;
3197 spin_unlock_irqrestore(&info->lock, flags);
3198 port->blocked_open++;
3199
3200 while (1) {
3201 if (C_BAUD(tty) && tty_port_initialized(port))
3202 tty_port_raise_dtr_rts(port);
3203
3204 set_current_state(TASK_INTERRUPTIBLE);
3205
3206 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
3207 retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3208 -EAGAIN : -ERESTARTSYS;
3209 break;
3210 }
3211
3212 cd = tty_port_carrier_raised(port);
3213 if (do_clocal || cd)
3214 break;
3215
3216 if (signal_pending(current)) {
3217 retval = -ERESTARTSYS;
3218 break;
3219 }
3220
3221 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3222 tty_unlock(tty);
3223 schedule();
3224 tty_lock(tty);
3225 }
3226
3227 set_current_state(TASK_RUNNING);
3228 remove_wait_queue(&port->open_wait, &wait);
3229
3230 if (!tty_hung_up_p(filp))
3231 port->count++;
3232 port->blocked_open--;
3233
3234 if (!retval)
3235 tty_port_set_active(port, 1);
3236
3237 DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3238 return retval;
3239}
3240
3241/*
3242 * allocate buffers used for calling line discipline receive_buf
3243 * directly in synchronous mode
3244 * note: add 5 bytes to max frame size to allow appending
3245 * 32-bit CRC and status byte when configured to do so
3246 */
3247static int alloc_tmp_rbuf(struct slgt_info *info)
3248{
3249 info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3250 if (info->tmp_rbuf == NULL)
3251 return -ENOMEM;
3252 /* unused flag buffer to satisfy receive_buf calling interface */
3253 info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL);
3254 if (!info->flag_buf) {
3255 kfree(info->tmp_rbuf);
3256 info->tmp_rbuf = NULL;
3257 return -ENOMEM;
3258 }
3259 return 0;
3260}
3261
3262static void free_tmp_rbuf(struct slgt_info *info)
3263{
3264 kfree(info->tmp_rbuf);
3265 info->tmp_rbuf = NULL;
3266 kfree(info->flag_buf);
3267 info->flag_buf = NULL;
3268}
3269
3270/*
3271 * allocate DMA descriptor lists.
3272 */
3273static int alloc_desc(struct slgt_info *info)
3274{
3275 unsigned int i;
3276 unsigned int pbufs;
3277
3278 /* allocate memory to hold descriptor lists */
3279 info->bufs = dma_alloc_coherent(&info->pdev->dev, DESC_LIST_SIZE,
3280 &info->bufs_dma_addr, GFP_KERNEL);
3281 if (info->bufs == NULL)
3282 return -ENOMEM;
3283
3284 info->rbufs = (struct slgt_desc*)info->bufs;
3285 info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3286
3287 pbufs = (unsigned int)info->bufs_dma_addr;
3288
3289 /*
3290 * Build circular lists of descriptors
3291 */
3292
3293 for (i=0; i < info->rbuf_count; i++) {
3294 /* physical address of this descriptor */
3295 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3296
3297 /* physical address of next descriptor */
3298 if (i == info->rbuf_count - 1)
3299 info->rbufs[i].next = cpu_to_le32(pbufs);
3300 else
3301 info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3302 set_desc_count(info->rbufs[i], DMABUFSIZE);
3303 }
3304
3305 for (i=0; i < info->tbuf_count; i++) {
3306 /* physical address of this descriptor */
3307 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3308
3309 /* physical address of next descriptor */
3310 if (i == info->tbuf_count - 1)
3311 info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3312 else
3313 info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3314 }
3315
3316 return 0;
3317}
3318
3319static void free_desc(struct slgt_info *info)
3320{
3321 if (info->bufs != NULL) {
3322 dma_free_coherent(&info->pdev->dev, DESC_LIST_SIZE,
3323 info->bufs, info->bufs_dma_addr);
3324 info->bufs = NULL;
3325 info->rbufs = NULL;
3326 info->tbufs = NULL;
3327 }
3328}
3329
3330static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3331{
3332 int i;
3333 for (i=0; i < count; i++) {
3334 bufs[i].buf = dma_alloc_coherent(&info->pdev->dev, DMABUFSIZE,
3335 &bufs[i].buf_dma_addr, GFP_KERNEL);
3336 if (!bufs[i].buf)
3337 return -ENOMEM;
3338 bufs[i].pbuf = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3339 }
3340 return 0;
3341}
3342
3343static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3344{
3345 int i;
3346 for (i=0; i < count; i++) {
3347 if (bufs[i].buf == NULL)
3348 continue;
3349 dma_free_coherent(&info->pdev->dev, DMABUFSIZE, bufs[i].buf,
3350 bufs[i].buf_dma_addr);
3351 bufs[i].buf = NULL;
3352 }
3353}
3354
3355static int alloc_dma_bufs(struct slgt_info *info)
3356{
3357 info->rbuf_count = 32;
3358 info->tbuf_count = 32;
3359
3360 if (alloc_desc(info) < 0 ||
3361 alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3362 alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3363 alloc_tmp_rbuf(info) < 0) {
3364 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3365 return -ENOMEM;
3366 }
3367 reset_rbufs(info);
3368 return 0;
3369}
3370
3371static void free_dma_bufs(struct slgt_info *info)
3372{
3373 if (info->bufs) {
3374 free_bufs(info, info->rbufs, info->rbuf_count);
3375 free_bufs(info, info->tbufs, info->tbuf_count);
3376 free_desc(info);
3377 }
3378 free_tmp_rbuf(info);
3379}
3380
3381static int claim_resources(struct slgt_info *info)
3382{
3383 if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3384 DBGERR(("%s reg addr conflict, addr=%08X\n",
3385 info->device_name, info->phys_reg_addr));
3386 info->init_error = DiagStatus_AddressConflict;
3387 goto errout;
3388 }
3389 else
3390 info->reg_addr_requested = true;
3391
3392 info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
3393 if (!info->reg_addr) {
3394 DBGERR(("%s can't map device registers, addr=%08X\n",
3395 info->device_name, info->phys_reg_addr));
3396 info->init_error = DiagStatus_CantAssignPciResources;
3397 goto errout;
3398 }
3399 return 0;
3400
3401errout:
3402 release_resources(info);
3403 return -ENODEV;
3404}
3405
3406static void release_resources(struct slgt_info *info)
3407{
3408 if (info->irq_requested) {
3409 free_irq(info->irq_level, info);
3410 info->irq_requested = false;
3411 }
3412
3413 if (info->reg_addr_requested) {
3414 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3415 info->reg_addr_requested = false;
3416 }
3417
3418 if (info->reg_addr) {
3419 iounmap(info->reg_addr);
3420 info->reg_addr = NULL;
3421 }
3422}
3423
3424/* Add the specified device instance data structure to the
3425 * global linked list of devices and increment the device count.
3426 */
3427static void add_device(struct slgt_info *info)
3428{
3429 char *devstr;
3430
3431 info->next_device = NULL;
3432 info->line = slgt_device_count;
3433 sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3434
3435 if (info->line < MAX_DEVICES) {
3436 if (maxframe[info->line])
3437 info->max_frame_size = maxframe[info->line];
3438 }
3439
3440 slgt_device_count++;
3441
3442 if (!slgt_device_list)
3443 slgt_device_list = info;
3444 else {
3445 struct slgt_info *current_dev = slgt_device_list;
3446 while(current_dev->next_device)
3447 current_dev = current_dev->next_device;
3448 current_dev->next_device = info;
3449 }
3450
3451 if (info->max_frame_size < 4096)
3452 info->max_frame_size = 4096;
3453 else if (info->max_frame_size > 65535)
3454 info->max_frame_size = 65535;
3455
3456 switch(info->pdev->device) {
3457 case SYNCLINK_GT_DEVICE_ID:
3458 devstr = "GT";
3459 break;
3460 case SYNCLINK_GT2_DEVICE_ID:
3461 devstr = "GT2";
3462 break;
3463 case SYNCLINK_GT4_DEVICE_ID:
3464 devstr = "GT4";
3465 break;
3466 case SYNCLINK_AC_DEVICE_ID:
3467 devstr = "AC";
3468 info->params.mode = MGSL_MODE_ASYNC;
3469 break;
3470 default:
3471 devstr = "(unknown model)";
3472 }
3473 printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3474 devstr, info->device_name, info->phys_reg_addr,
3475 info->irq_level, info->max_frame_size);
3476
3477#if SYNCLINK_GENERIC_HDLC
3478 hdlcdev_init(info);
3479#endif
3480}
3481
3482static const struct tty_port_operations slgt_port_ops = {
3483 .carrier_raised = carrier_raised,
3484 .dtr_rts = dtr_rts,
3485};
3486
3487/*
3488 * allocate device instance structure, return NULL on failure
3489 */
3490static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3491{
3492 struct slgt_info *info;
3493
3494 info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3495
3496 if (!info) {
3497 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3498 driver_name, adapter_num, port_num));
3499 } else {
3500 tty_port_init(&info->port);
3501 info->port.ops = &slgt_port_ops;
3502 info->magic = MGSL_MAGIC;
3503 INIT_WORK(&info->task, bh_handler);
3504 info->max_frame_size = 4096;
3505 info->base_clock = 14745600;
3506 info->rbuf_fill_level = DMABUFSIZE;
3507 init_waitqueue_head(&info->status_event_wait_q);
3508 init_waitqueue_head(&info->event_wait_q);
3509 spin_lock_init(&info->netlock);
3510 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3511 info->idle_mode = HDLC_TXIDLE_FLAGS;
3512 info->adapter_num = adapter_num;
3513 info->port_num = port_num;
3514
3515 timer_setup(&info->tx_timer, tx_timeout, 0);
3516 timer_setup(&info->rx_timer, rx_timeout, 0);
3517
3518 /* Copy configuration info to device instance data */
3519 info->pdev = pdev;
3520 info->irq_level = pdev->irq;
3521 info->phys_reg_addr = pci_resource_start(pdev,0);
3522
3523 info->bus_type = MGSL_BUS_TYPE_PCI;
3524 info->irq_flags = IRQF_SHARED;
3525
3526 info->init_error = -1; /* assume error, set to 0 on successful init */
3527 }
3528
3529 return info;
3530}
3531
3532static void device_init(int adapter_num, struct pci_dev *pdev)
3533{
3534 struct slgt_info *port_array[SLGT_MAX_PORTS];
3535 int i;
3536 int port_count = 1;
3537
3538 if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3539 port_count = 2;
3540 else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3541 port_count = 4;
3542
3543 /* allocate device instances for all ports */
3544 for (i=0; i < port_count; ++i) {
3545 port_array[i] = alloc_dev(adapter_num, i, pdev);
3546 if (port_array[i] == NULL) {
3547 for (--i; i >= 0; --i) {
3548 tty_port_destroy(&port_array[i]->port);
3549 kfree(port_array[i]);
3550 }
3551 return;
3552 }
3553 }
3554
3555 /* give copy of port_array to all ports and add to device list */
3556 for (i=0; i < port_count; ++i) {
3557 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3558 add_device(port_array[i]);
3559 port_array[i]->port_count = port_count;
3560 spin_lock_init(&port_array[i]->lock);
3561 }
3562
3563 /* Allocate and claim adapter resources */
3564 if (!claim_resources(port_array[0])) {
3565
3566 alloc_dma_bufs(port_array[0]);
3567
3568 /* copy resource information from first port to others */
3569 for (i = 1; i < port_count; ++i) {
3570 port_array[i]->irq_level = port_array[0]->irq_level;
3571 port_array[i]->reg_addr = port_array[0]->reg_addr;
3572 alloc_dma_bufs(port_array[i]);
3573 }
3574
3575 if (request_irq(port_array[0]->irq_level,
3576 slgt_interrupt,
3577 port_array[0]->irq_flags,
3578 port_array[0]->device_name,
3579 port_array[0]) < 0) {
3580 DBGERR(("%s request_irq failed IRQ=%d\n",
3581 port_array[0]->device_name,
3582 port_array[0]->irq_level));
3583 } else {
3584 port_array[0]->irq_requested = true;
3585 adapter_test(port_array[0]);
3586 for (i=1 ; i < port_count ; i++) {
3587 port_array[i]->init_error = port_array[0]->init_error;
3588 port_array[i]->gpio_present = port_array[0]->gpio_present;
3589 }
3590 }
3591 }
3592
3593 for (i = 0; i < port_count; ++i) {
3594 struct slgt_info *info = port_array[i];
3595 tty_port_register_device(&info->port, serial_driver, info->line,
3596 &info->pdev->dev);
3597 }
3598}
3599
3600static int init_one(struct pci_dev *dev,
3601 const struct pci_device_id *ent)
3602{
3603 if (pci_enable_device(dev)) {
3604 printk("error enabling pci device %p\n", dev);
3605 return -EIO;
3606 }
3607 pci_set_master(dev);
3608 device_init(slgt_device_count, dev);
3609 return 0;
3610}
3611
3612static void remove_one(struct pci_dev *dev)
3613{
3614}
3615
3616static const struct tty_operations ops = {
3617 .open = open,
3618 .close = close,
3619 .write = write,
3620 .put_char = put_char,
3621 .flush_chars = flush_chars,
3622 .write_room = write_room,
3623 .chars_in_buffer = chars_in_buffer,
3624 .flush_buffer = flush_buffer,
3625 .ioctl = ioctl,
3626 .compat_ioctl = slgt_compat_ioctl,
3627 .throttle = throttle,
3628 .unthrottle = unthrottle,
3629 .send_xchar = send_xchar,
3630 .break_ctl = set_break,
3631 .wait_until_sent = wait_until_sent,
3632 .set_termios = set_termios,
3633 .stop = tx_hold,
3634 .start = tx_release,
3635 .hangup = hangup,
3636 .tiocmget = tiocmget,
3637 .tiocmset = tiocmset,
3638 .get_icount = get_icount,
3639 .proc_show = synclink_gt_proc_show,
3640};
3641
3642static void slgt_cleanup(void)
3643{
3644 struct slgt_info *info;
3645 struct slgt_info *tmp;
3646
3647 printk(KERN_INFO "unload %s\n", driver_name);
3648
3649 if (serial_driver) {
3650 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3651 tty_unregister_device(serial_driver, info->line);
3652 tty_unregister_driver(serial_driver);
3653 put_tty_driver(serial_driver);
3654 }
3655
3656 /* reset devices */
3657 info = slgt_device_list;
3658 while(info) {
3659 reset_port(info);
3660 info = info->next_device;
3661 }
3662
3663 /* release devices */
3664 info = slgt_device_list;
3665 while(info) {
3666#if SYNCLINK_GENERIC_HDLC
3667 hdlcdev_exit(info);
3668#endif
3669 free_dma_bufs(info);
3670 free_tmp_rbuf(info);
3671 if (info->port_num == 0)
3672 release_resources(info);
3673 tmp = info;
3674 info = info->next_device;
3675 tty_port_destroy(&tmp->port);
3676 kfree(tmp);
3677 }
3678
3679 if (pci_registered)
3680 pci_unregister_driver(&pci_driver);
3681}
3682
3683/*
3684 * Driver initialization entry point.
3685 */
3686static int __init slgt_init(void)
3687{
3688 int rc;
3689
3690 printk(KERN_INFO "%s\n", driver_name);
3691
3692 serial_driver = alloc_tty_driver(MAX_DEVICES);
3693 if (!serial_driver) {
3694 printk("%s can't allocate tty driver\n", driver_name);
3695 return -ENOMEM;
3696 }
3697
3698 /* Initialize the tty_driver structure */
3699
3700 serial_driver->driver_name = slgt_driver_name;
3701 serial_driver->name = tty_dev_prefix;
3702 serial_driver->major = ttymajor;
3703 serial_driver->minor_start = 64;
3704 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3705 serial_driver->subtype = SERIAL_TYPE_NORMAL;
3706 serial_driver->init_termios = tty_std_termios;
3707 serial_driver->init_termios.c_cflag =
3708 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3709 serial_driver->init_termios.c_ispeed = 9600;
3710 serial_driver->init_termios.c_ospeed = 9600;
3711 serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3712 tty_set_operations(serial_driver, &ops);
3713 if ((rc = tty_register_driver(serial_driver)) < 0) {
3714 DBGERR(("%s can't register serial driver\n", driver_name));
3715 put_tty_driver(serial_driver);
3716 serial_driver = NULL;
3717 goto error;
3718 }
3719
3720 printk(KERN_INFO "%s, tty major#%d\n",
3721 driver_name, serial_driver->major);
3722
3723 slgt_device_count = 0;
3724 if ((rc = pci_register_driver(&pci_driver)) < 0) {
3725 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3726 goto error;
3727 }
3728 pci_registered = true;
3729
3730 if (!slgt_device_list)
3731 printk("%s no devices found\n",driver_name);
3732
3733 return 0;
3734
3735error:
3736 slgt_cleanup();
3737 return rc;
3738}
3739
3740static void __exit slgt_exit(void)
3741{
3742 slgt_cleanup();
3743}
3744
3745module_init(slgt_init);
3746module_exit(slgt_exit);
3747
3748/*
3749 * register access routines
3750 */
3751
3752#define CALC_REGADDR() \
3753 unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3754 if (addr >= 0x80) \
3755 reg_addr += (info->port_num) * 32; \
3756 else if (addr >= 0x40) \
3757 reg_addr += (info->port_num) * 16;
3758
3759static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3760{
3761 CALC_REGADDR();
3762 return readb((void __iomem *)reg_addr);
3763}
3764
3765static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3766{
3767 CALC_REGADDR();
3768 writeb(value, (void __iomem *)reg_addr);
3769}
3770
3771static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3772{
3773 CALC_REGADDR();
3774 return readw((void __iomem *)reg_addr);
3775}
3776
3777static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3778{
3779 CALC_REGADDR();
3780 writew(value, (void __iomem *)reg_addr);
3781}
3782
3783static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3784{
3785 CALC_REGADDR();
3786 return readl((void __iomem *)reg_addr);
3787}
3788
3789static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3790{
3791 CALC_REGADDR();
3792 writel(value, (void __iomem *)reg_addr);
3793}
3794
3795static void rdma_reset(struct slgt_info *info)
3796{
3797 unsigned int i;
3798
3799 /* set reset bit */
3800 wr_reg32(info, RDCSR, BIT1);
3801
3802 /* wait for enable bit cleared */
3803 for(i=0 ; i < 1000 ; i++)
3804 if (!(rd_reg32(info, RDCSR) & BIT0))
3805 break;
3806}
3807
3808static void tdma_reset(struct slgt_info *info)
3809{
3810 unsigned int i;
3811
3812 /* set reset bit */
3813 wr_reg32(info, TDCSR, BIT1);
3814
3815 /* wait for enable bit cleared */
3816 for(i=0 ; i < 1000 ; i++)
3817 if (!(rd_reg32(info, TDCSR) & BIT0))
3818 break;
3819}
3820
3821/*
3822 * enable internal loopback
3823 * TxCLK and RxCLK are generated from BRG
3824 * and TxD is looped back to RxD internally.
3825 */
3826static void enable_loopback(struct slgt_info *info)
3827{
3828 /* SCR (serial control) BIT2=loopback enable */
3829 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3830
3831 if (info->params.mode != MGSL_MODE_ASYNC) {
3832 /* CCR (clock control)
3833 * 07..05 tx clock source (010 = BRG)
3834 * 04..02 rx clock source (010 = BRG)
3835 * 01 auxclk enable (0 = disable)
3836 * 00 BRG enable (1 = enable)
3837 *
3838 * 0100 1001
3839 */
3840 wr_reg8(info, CCR, 0x49);
3841
3842 /* set speed if available, otherwise use default */
3843 if (info->params.clock_speed)
3844 set_rate(info, info->params.clock_speed);
3845 else
3846 set_rate(info, 3686400);
3847 }
3848}
3849
3850/*
3851 * set baud rate generator to specified rate
3852 */
3853static void set_rate(struct slgt_info *info, u32 rate)
3854{
3855 unsigned int div;
3856 unsigned int osc = info->base_clock;
3857
3858 /* div = osc/rate - 1
3859 *
3860 * Round div up if osc/rate is not integer to
3861 * force to next slowest rate.
3862 */
3863
3864 if (rate) {
3865 div = osc/rate;
3866 if (!(osc % rate) && div)
3867 div--;
3868 wr_reg16(info, BDR, (unsigned short)div);
3869 }
3870}
3871
3872static void rx_stop(struct slgt_info *info)
3873{
3874 unsigned short val;
3875
3876 /* disable and reset receiver */
3877 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3878 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3879 wr_reg16(info, RCR, val); /* clear reset bit */
3880
3881 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3882
3883 /* clear pending rx interrupts */
3884 wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3885
3886 rdma_reset(info);
3887
3888 info->rx_enabled = false;
3889 info->rx_restart = false;
3890}
3891
3892static void rx_start(struct slgt_info *info)
3893{
3894 unsigned short val;
3895
3896 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3897
3898 /* clear pending rx overrun IRQ */
3899 wr_reg16(info, SSR, IRQ_RXOVER);
3900
3901 /* reset and disable receiver */
3902 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3903 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3904 wr_reg16(info, RCR, val); /* clear reset bit */
3905
3906 rdma_reset(info);
3907 reset_rbufs(info);
3908
3909 if (info->rx_pio) {
3910 /* rx request when rx FIFO not empty */
3911 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
3912 slgt_irq_on(info, IRQ_RXDATA);
3913 if (info->params.mode == MGSL_MODE_ASYNC) {
3914 /* enable saving of rx status */
3915 wr_reg32(info, RDCSR, BIT6);
3916 }
3917 } else {
3918 /* rx request when rx FIFO half full */
3919 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
3920 /* set 1st descriptor address */
3921 wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3922
3923 if (info->params.mode != MGSL_MODE_ASYNC) {
3924 /* enable rx DMA and DMA interrupt */
3925 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3926 } else {
3927 /* enable saving of rx status, rx DMA and DMA interrupt */
3928 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3929 }
3930 }
3931
3932 slgt_irq_on(info, IRQ_RXOVER);
3933
3934 /* enable receiver */
3935 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3936
3937 info->rx_restart = false;
3938 info->rx_enabled = true;
3939}
3940
3941static void tx_start(struct slgt_info *info)
3942{
3943 if (!info->tx_enabled) {
3944 wr_reg16(info, TCR,
3945 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
3946 info->tx_enabled = true;
3947 }
3948
3949 if (desc_count(info->tbufs[info->tbuf_start])) {
3950 info->drop_rts_on_tx_done = false;
3951
3952 if (info->params.mode != MGSL_MODE_ASYNC) {
3953 if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3954 get_gtsignals(info);
3955 if (!(info->signals & SerialSignal_RTS)) {
3956 info->signals |= SerialSignal_RTS;
3957 set_gtsignals(info);
3958 info->drop_rts_on_tx_done = true;
3959 }
3960 }
3961
3962 slgt_irq_off(info, IRQ_TXDATA);
3963 slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3964 /* clear tx idle and underrun status bits */
3965 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3966 } else {
3967 slgt_irq_off(info, IRQ_TXDATA);
3968 slgt_irq_on(info, IRQ_TXIDLE);
3969 /* clear tx idle status bit */
3970 wr_reg16(info, SSR, IRQ_TXIDLE);
3971 }
3972 /* set 1st descriptor address and start DMA */
3973 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3974 wr_reg32(info, TDCSR, BIT2 + BIT0);
3975 info->tx_active = true;
3976 }
3977}
3978
3979static void tx_stop(struct slgt_info *info)
3980{
3981 unsigned short val;
3982
3983 del_timer(&info->tx_timer);
3984
3985 tdma_reset(info);
3986
3987 /* reset and disable transmitter */
3988 val = rd_reg16(info, TCR) & ~BIT1; /* clear enable bit */
3989 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3990
3991 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3992
3993 /* clear tx idle and underrun status bit */
3994 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3995
3996 reset_tbufs(info);
3997
3998 info->tx_enabled = false;
3999 info->tx_active = false;
4000}
4001
4002static void reset_port(struct slgt_info *info)
4003{
4004 if (!info->reg_addr)
4005 return;
4006
4007 tx_stop(info);
4008 rx_stop(info);
4009
4010 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
4011 set_gtsignals(info);
4012
4013 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4014}
4015
4016static void reset_adapter(struct slgt_info *info)
4017{
4018 int i;
4019 for (i=0; i < info->port_count; ++i) {
4020 if (info->port_array[i])
4021 reset_port(info->port_array[i]);
4022 }
4023}
4024
4025static void async_mode(struct slgt_info *info)
4026{
4027 unsigned short val;
4028
4029 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4030 tx_stop(info);
4031 rx_stop(info);
4032
4033 /* TCR (tx control)
4034 *
4035 * 15..13 mode, 010=async
4036 * 12..10 encoding, 000=NRZ
4037 * 09 parity enable
4038 * 08 1=odd parity, 0=even parity
4039 * 07 1=RTS driver control
4040 * 06 1=break enable
4041 * 05..04 character length
4042 * 00=5 bits
4043 * 01=6 bits
4044 * 10=7 bits
4045 * 11=8 bits
4046 * 03 0=1 stop bit, 1=2 stop bits
4047 * 02 reset
4048 * 01 enable
4049 * 00 auto-CTS enable
4050 */
4051 val = 0x4000;
4052
4053 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4054 val |= BIT7;
4055
4056 if (info->params.parity != ASYNC_PARITY_NONE) {
4057 val |= BIT9;
4058 if (info->params.parity == ASYNC_PARITY_ODD)
4059 val |= BIT8;
4060 }
4061
4062 switch (info->params.data_bits)
4063 {
4064 case 6: val |= BIT4; break;
4065 case 7: val |= BIT5; break;
4066 case 8: val |= BIT5 + BIT4; break;
4067 }
4068
4069 if (info->params.stop_bits != 1)
4070 val |= BIT3;
4071
4072 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4073 val |= BIT0;
4074
4075 wr_reg16(info, TCR, val);
4076
4077 /* RCR (rx control)
4078 *
4079 * 15..13 mode, 010=async
4080 * 12..10 encoding, 000=NRZ
4081 * 09 parity enable
4082 * 08 1=odd parity, 0=even parity
4083 * 07..06 reserved, must be 0
4084 * 05..04 character length
4085 * 00=5 bits
4086 * 01=6 bits
4087 * 10=7 bits
4088 * 11=8 bits
4089 * 03 reserved, must be zero
4090 * 02 reset
4091 * 01 enable
4092 * 00 auto-DCD enable
4093 */
4094 val = 0x4000;
4095
4096 if (info->params.parity != ASYNC_PARITY_NONE) {
4097 val |= BIT9;
4098 if (info->params.parity == ASYNC_PARITY_ODD)
4099 val |= BIT8;
4100 }
4101
4102 switch (info->params.data_bits)
4103 {
4104 case 6: val |= BIT4; break;
4105 case 7: val |= BIT5; break;
4106 case 8: val |= BIT5 + BIT4; break;
4107 }
4108
4109 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4110 val |= BIT0;
4111
4112 wr_reg16(info, RCR, val);
4113
4114 /* CCR (clock control)
4115 *
4116 * 07..05 011 = tx clock source is BRG/16
4117 * 04..02 010 = rx clock source is BRG
4118 * 01 0 = auxclk disabled
4119 * 00 1 = BRG enabled
4120 *
4121 * 0110 1001
4122 */
4123 wr_reg8(info, CCR, 0x69);
4124
4125 msc_set_vcr(info);
4126
4127 /* SCR (serial control)
4128 *
4129 * 15 1=tx req on FIFO half empty
4130 * 14 1=rx req on FIFO half full
4131 * 13 tx data IRQ enable
4132 * 12 tx idle IRQ enable
4133 * 11 rx break on IRQ enable
4134 * 10 rx data IRQ enable
4135 * 09 rx break off IRQ enable
4136 * 08 overrun IRQ enable
4137 * 07 DSR IRQ enable
4138 * 06 CTS IRQ enable
4139 * 05 DCD IRQ enable
4140 * 04 RI IRQ enable
4141 * 03 0=16x sampling, 1=8x sampling
4142 * 02 1=txd->rxd internal loopback enable
4143 * 01 reserved, must be zero
4144 * 00 1=master IRQ enable
4145 */
4146 val = BIT15 + BIT14 + BIT0;
4147 /* JCR[8] : 1 = x8 async mode feature available */
4148 if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4149 ((info->base_clock < (info->params.data_rate * 16)) ||
4150 (info->base_clock % (info->params.data_rate * 16)))) {
4151 /* use 8x sampling */
4152 val |= BIT3;
4153 set_rate(info, info->params.data_rate * 8);
4154 } else {
4155 /* use 16x sampling */
4156 set_rate(info, info->params.data_rate * 16);
4157 }
4158 wr_reg16(info, SCR, val);
4159
4160 slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4161
4162 if (info->params.loopback)
4163 enable_loopback(info);
4164}
4165
4166static void sync_mode(struct slgt_info *info)
4167{
4168 unsigned short val;
4169
4170 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4171 tx_stop(info);
4172 rx_stop(info);
4173
4174 /* TCR (tx control)
4175 *
4176 * 15..13 mode
4177 * 000=HDLC/SDLC
4178 * 001=raw bit synchronous
4179 * 010=asynchronous/isochronous
4180 * 011=monosync byte synchronous
4181 * 100=bisync byte synchronous
4182 * 101=xsync byte synchronous
4183 * 12..10 encoding
4184 * 09 CRC enable
4185 * 08 CRC32
4186 * 07 1=RTS driver control
4187 * 06 preamble enable
4188 * 05..04 preamble length
4189 * 03 share open/close flag
4190 * 02 reset
4191 * 01 enable
4192 * 00 auto-CTS enable
4193 */
4194 val = BIT2;
4195
4196 switch(info->params.mode) {
4197 case MGSL_MODE_XSYNC:
4198 val |= BIT15 + BIT13;
4199 break;
4200 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4201 case MGSL_MODE_BISYNC: val |= BIT15; break;
4202 case MGSL_MODE_RAW: val |= BIT13; break;
4203 }
4204 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4205 val |= BIT7;
4206
4207 switch(info->params.encoding)
4208 {
4209 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4210 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4211 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4212 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4213 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4214 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4215 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4216 }
4217
4218 switch (info->params.crc_type & HDLC_CRC_MASK)
4219 {
4220 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4221 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4222 }
4223
4224 if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4225 val |= BIT6;
4226
4227 switch (info->params.preamble_length)
4228 {
4229 case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4230 case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4231 case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4232 }
4233
4234 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4235 val |= BIT0;
4236
4237 wr_reg16(info, TCR, val);
4238
4239 /* TPR (transmit preamble) */
4240
4241 switch (info->params.preamble)
4242 {
4243 case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4244 case HDLC_PREAMBLE_PATTERN_ONES: val = 0xff; break;
4245 case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4246 case HDLC_PREAMBLE_PATTERN_10: val = 0x55; break;
4247 case HDLC_PREAMBLE_PATTERN_01: val = 0xaa; break;
4248 default: val = 0x7e; break;
4249 }
4250 wr_reg8(info, TPR, (unsigned char)val);
4251
4252 /* RCR (rx control)
4253 *
4254 * 15..13 mode
4255 * 000=HDLC/SDLC
4256 * 001=raw bit synchronous
4257 * 010=asynchronous/isochronous
4258 * 011=monosync byte synchronous
4259 * 100=bisync byte synchronous
4260 * 101=xsync byte synchronous
4261 * 12..10 encoding
4262 * 09 CRC enable
4263 * 08 CRC32
4264 * 07..03 reserved, must be 0
4265 * 02 reset
4266 * 01 enable
4267 * 00 auto-DCD enable
4268 */
4269 val = 0;
4270
4271 switch(info->params.mode) {
4272 case MGSL_MODE_XSYNC:
4273 val |= BIT15 + BIT13;
4274 break;
4275 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4276 case MGSL_MODE_BISYNC: val |= BIT15; break;
4277 case MGSL_MODE_RAW: val |= BIT13; break;
4278 }
4279
4280 switch(info->params.encoding)
4281 {
4282 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4283 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4284 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4285 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4286 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4287 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4288 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4289 }
4290
4291 switch (info->params.crc_type & HDLC_CRC_MASK)
4292 {
4293 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4294 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4295 }
4296
4297 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4298 val |= BIT0;
4299
4300 wr_reg16(info, RCR, val);
4301
4302 /* CCR (clock control)
4303 *
4304 * 07..05 tx clock source
4305 * 04..02 rx clock source
4306 * 01 auxclk enable
4307 * 00 BRG enable
4308 */
4309 val = 0;
4310
4311 if (info->params.flags & HDLC_FLAG_TXC_BRG)
4312 {
4313 // when RxC source is DPLL, BRG generates 16X DPLL
4314 // reference clock, so take TxC from BRG/16 to get
4315 // transmit clock at actual data rate
4316 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4317 val |= BIT6 + BIT5; /* 011, txclk = BRG/16 */
4318 else
4319 val |= BIT6; /* 010, txclk = BRG */
4320 }
4321 else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4322 val |= BIT7; /* 100, txclk = DPLL Input */
4323 else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4324 val |= BIT5; /* 001, txclk = RXC Input */
4325
4326 if (info->params.flags & HDLC_FLAG_RXC_BRG)
4327 val |= BIT3; /* 010, rxclk = BRG */
4328 else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4329 val |= BIT4; /* 100, rxclk = DPLL */
4330 else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4331 val |= BIT2; /* 001, rxclk = TXC Input */
4332
4333 if (info->params.clock_speed)
4334 val |= BIT1 + BIT0;
4335
4336 wr_reg8(info, CCR, (unsigned char)val);
4337
4338 if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4339 {
4340 // program DPLL mode
4341 switch(info->params.encoding)
4342 {
4343 case HDLC_ENCODING_BIPHASE_MARK:
4344 case HDLC_ENCODING_BIPHASE_SPACE:
4345 val = BIT7; break;
4346 case HDLC_ENCODING_BIPHASE_LEVEL:
4347 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4348 val = BIT7 + BIT6; break;
4349 default: val = BIT6; // NRZ encodings
4350 }
4351 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4352
4353 // DPLL requires a 16X reference clock from BRG
4354 set_rate(info, info->params.clock_speed * 16);
4355 }
4356 else
4357 set_rate(info, info->params.clock_speed);
4358
4359 tx_set_idle(info);
4360
4361 msc_set_vcr(info);
4362
4363 /* SCR (serial control)
4364 *
4365 * 15 1=tx req on FIFO half empty
4366 * 14 1=rx req on FIFO half full
4367 * 13 tx data IRQ enable
4368 * 12 tx idle IRQ enable
4369 * 11 underrun IRQ enable
4370 * 10 rx data IRQ enable
4371 * 09 rx idle IRQ enable
4372 * 08 overrun IRQ enable
4373 * 07 DSR IRQ enable
4374 * 06 CTS IRQ enable
4375 * 05 DCD IRQ enable
4376 * 04 RI IRQ enable
4377 * 03 reserved, must be zero
4378 * 02 1=txd->rxd internal loopback enable
4379 * 01 reserved, must be zero
4380 * 00 1=master IRQ enable
4381 */
4382 wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4383
4384 if (info->params.loopback)
4385 enable_loopback(info);
4386}
4387
4388/*
4389 * set transmit idle mode
4390 */
4391static void tx_set_idle(struct slgt_info *info)
4392{
4393 unsigned char val;
4394 unsigned short tcr;
4395
4396 /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4397 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4398 */
4399 tcr = rd_reg16(info, TCR);
4400 if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4401 /* disable preamble, set idle size to 16 bits */
4402 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4403 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4404 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4405 } else if (!(tcr & BIT6)) {
4406 /* preamble is disabled, set idle size to 8 bits */
4407 tcr &= ~(BIT5 + BIT4);
4408 }
4409 wr_reg16(info, TCR, tcr);
4410
4411 if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4412 /* LSB of custom tx idle specified in tx idle register */
4413 val = (unsigned char)(info->idle_mode & 0xff);
4414 } else {
4415 /* standard 8 bit idle patterns */
4416 switch(info->idle_mode)
4417 {
4418 case HDLC_TXIDLE_FLAGS: val = 0x7e; break;
4419 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4420 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4421 case HDLC_TXIDLE_ZEROS:
4422 case HDLC_TXIDLE_SPACE: val = 0x00; break;
4423 default: val = 0xff;
4424 }
4425 }
4426
4427 wr_reg8(info, TIR, val);
4428}
4429
4430/*
4431 * get state of V24 status (input) signals
4432 */
4433static void get_gtsignals(struct slgt_info *info)
4434{
4435 unsigned short status = rd_reg16(info, SSR);
4436
4437 /* clear all serial signals except RTS and DTR */
4438 info->signals &= SerialSignal_RTS | SerialSignal_DTR;
4439
4440 if (status & BIT3)
4441 info->signals |= SerialSignal_DSR;
4442 if (status & BIT2)
4443 info->signals |= SerialSignal_CTS;
4444 if (status & BIT1)
4445 info->signals |= SerialSignal_DCD;
4446 if (status & BIT0)
4447 info->signals |= SerialSignal_RI;
4448}
4449
4450/*
4451 * set V.24 Control Register based on current configuration
4452 */
4453static void msc_set_vcr(struct slgt_info *info)
4454{
4455 unsigned char val = 0;
4456
4457 /* VCR (V.24 control)
4458 *
4459 * 07..04 serial IF select
4460 * 03 DTR
4461 * 02 RTS
4462 * 01 LL
4463 * 00 RL
4464 */
4465
4466 switch(info->if_mode & MGSL_INTERFACE_MASK)
4467 {
4468 case MGSL_INTERFACE_RS232:
4469 val |= BIT5; /* 0010 */
4470 break;
4471 case MGSL_INTERFACE_V35:
4472 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4473 break;
4474 case MGSL_INTERFACE_RS422:
4475 val |= BIT6; /* 0100 */
4476 break;
4477 }
4478
4479 if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4480 val |= BIT4;
4481 if (info->signals & SerialSignal_DTR)
4482 val |= BIT3;
4483 if (info->signals & SerialSignal_RTS)
4484 val |= BIT2;
4485 if (info->if_mode & MGSL_INTERFACE_LL)
4486 val |= BIT1;
4487 if (info->if_mode & MGSL_INTERFACE_RL)
4488 val |= BIT0;
4489 wr_reg8(info, VCR, val);
4490}
4491
4492/*
4493 * set state of V24 control (output) signals
4494 */
4495static void set_gtsignals(struct slgt_info *info)
4496{
4497 unsigned char val = rd_reg8(info, VCR);
4498 if (info->signals & SerialSignal_DTR)
4499 val |= BIT3;
4500 else
4501 val &= ~BIT3;
4502 if (info->signals & SerialSignal_RTS)
4503 val |= BIT2;
4504 else
4505 val &= ~BIT2;
4506 wr_reg8(info, VCR, val);
4507}
4508
4509/*
4510 * free range of receive DMA buffers (i to last)
4511 */
4512static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4513{
4514 int done = 0;
4515
4516 while(!done) {
4517 /* reset current buffer for reuse */
4518 info->rbufs[i].status = 0;
4519 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4520 if (i == last)
4521 done = 1;
4522 if (++i == info->rbuf_count)
4523 i = 0;
4524 }
4525 info->rbuf_current = i;
4526}
4527
4528/*
4529 * mark all receive DMA buffers as free
4530 */
4531static void reset_rbufs(struct slgt_info *info)
4532{
4533 free_rbufs(info, 0, info->rbuf_count - 1);
4534 info->rbuf_fill_index = 0;
4535 info->rbuf_fill_count = 0;
4536}
4537
4538/*
4539 * pass receive HDLC frame to upper layer
4540 *
4541 * return true if frame available, otherwise false
4542 */
4543static bool rx_get_frame(struct slgt_info *info)
4544{
4545 unsigned int start, end;
4546 unsigned short status;
4547 unsigned int framesize = 0;
4548 unsigned long flags;
4549 struct tty_struct *tty = info->port.tty;
4550 unsigned char addr_field = 0xff;
4551 unsigned int crc_size = 0;
4552
4553 switch (info->params.crc_type & HDLC_CRC_MASK) {
4554 case HDLC_CRC_16_CCITT: crc_size = 2; break;
4555 case HDLC_CRC_32_CCITT: crc_size = 4; break;
4556 }
4557
4558check_again:
4559
4560 framesize = 0;
4561 addr_field = 0xff;
4562 start = end = info->rbuf_current;
4563
4564 for (;;) {
4565 if (!desc_complete(info->rbufs[end]))
4566 goto cleanup;
4567
4568 if (framesize == 0 && info->params.addr_filter != 0xff)
4569 addr_field = info->rbufs[end].buf[0];
4570
4571 framesize += desc_count(info->rbufs[end]);
4572
4573 if (desc_eof(info->rbufs[end]))
4574 break;
4575
4576 if (++end == info->rbuf_count)
4577 end = 0;
4578
4579 if (end == info->rbuf_current) {
4580 if (info->rx_enabled){
4581 spin_lock_irqsave(&info->lock,flags);
4582 rx_start(info);
4583 spin_unlock_irqrestore(&info->lock,flags);
4584 }
4585 goto cleanup;
4586 }
4587 }
4588
4589 /* status
4590 *
4591 * 15 buffer complete
4592 * 14..06 reserved
4593 * 05..04 residue
4594 * 02 eof (end of frame)
4595 * 01 CRC error
4596 * 00 abort
4597 */
4598 status = desc_status(info->rbufs[end]);
4599
4600 /* ignore CRC bit if not using CRC (bit is undefined) */
4601 if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4602 status &= ~BIT1;
4603
4604 if (framesize == 0 ||
4605 (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4606 free_rbufs(info, start, end);
4607 goto check_again;
4608 }
4609
4610 if (framesize < (2 + crc_size) || status & BIT0) {
4611 info->icount.rxshort++;
4612 framesize = 0;
4613 } else if (status & BIT1) {
4614 info->icount.rxcrc++;
4615 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4616 framesize = 0;
4617 }
4618
4619#if SYNCLINK_GENERIC_HDLC
4620 if (framesize == 0) {
4621 info->netdev->stats.rx_errors++;
4622 info->netdev->stats.rx_frame_errors++;
4623 }
4624#endif
4625
4626 DBGBH(("%s rx frame status=%04X size=%d\n",
4627 info->device_name, status, framesize));
4628 DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4629
4630 if (framesize) {
4631 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4632 framesize -= crc_size;
4633 crc_size = 0;
4634 }
4635
4636 if (framesize > info->max_frame_size + crc_size)
4637 info->icount.rxlong++;
4638 else {
4639 /* copy dma buffer(s) to contiguous temp buffer */
4640 int copy_count = framesize;
4641 int i = start;
4642 unsigned char *p = info->tmp_rbuf;
4643 info->tmp_rbuf_count = framesize;
4644
4645 info->icount.rxok++;
4646
4647 while(copy_count) {
4648 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4649 memcpy(p, info->rbufs[i].buf, partial_count);
4650 p += partial_count;
4651 copy_count -= partial_count;
4652 if (++i == info->rbuf_count)
4653 i = 0;
4654 }
4655
4656 if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4657 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4658 framesize++;
4659 }
4660
4661#if SYNCLINK_GENERIC_HDLC
4662 if (info->netcount)
4663 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4664 else
4665#endif
4666 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4667 }
4668 }
4669 free_rbufs(info, start, end);
4670 return true;
4671
4672cleanup:
4673 return false;
4674}
4675
4676/*
4677 * pass receive buffer (RAW synchronous mode) to tty layer
4678 * return true if buffer available, otherwise false
4679 */
4680static bool rx_get_buf(struct slgt_info *info)
4681{
4682 unsigned int i = info->rbuf_current;
4683 unsigned int count;
4684
4685 if (!desc_complete(info->rbufs[i]))
4686 return false;
4687 count = desc_count(info->rbufs[i]);
4688 switch(info->params.mode) {
4689 case MGSL_MODE_MONOSYNC:
4690 case MGSL_MODE_BISYNC:
4691 case MGSL_MODE_XSYNC:
4692 /* ignore residue in byte synchronous modes */
4693 if (desc_residue(info->rbufs[i]))
4694 count--;
4695 break;
4696 }
4697 DBGDATA(info, info->rbufs[i].buf, count, "rx");
4698 DBGINFO(("rx_get_buf size=%d\n", count));
4699 if (count)
4700 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4701 info->flag_buf, count);
4702 free_rbufs(info, i, i);
4703 return true;
4704}
4705
4706static void reset_tbufs(struct slgt_info *info)
4707{
4708 unsigned int i;
4709 info->tbuf_current = 0;
4710 for (i=0 ; i < info->tbuf_count ; i++) {
4711 info->tbufs[i].status = 0;
4712 info->tbufs[i].count = 0;
4713 }
4714}
4715
4716/*
4717 * return number of free transmit DMA buffers
4718 */
4719static unsigned int free_tbuf_count(struct slgt_info *info)
4720{
4721 unsigned int count = 0;
4722 unsigned int i = info->tbuf_current;
4723
4724 do
4725 {
4726 if (desc_count(info->tbufs[i]))
4727 break; /* buffer in use */
4728 ++count;
4729 if (++i == info->tbuf_count)
4730 i=0;
4731 } while (i != info->tbuf_current);
4732
4733 /* if tx DMA active, last zero count buffer is in use */
4734 if (count && (rd_reg32(info, TDCSR) & BIT0))
4735 --count;
4736
4737 return count;
4738}
4739
4740/*
4741 * return number of bytes in unsent transmit DMA buffers
4742 * and the serial controller tx FIFO
4743 */
4744static unsigned int tbuf_bytes(struct slgt_info *info)
4745{
4746 unsigned int total_count = 0;
4747 unsigned int i = info->tbuf_current;
4748 unsigned int reg_value;
4749 unsigned int count;
4750 unsigned int active_buf_count = 0;
4751
4752 /*
4753 * Add descriptor counts for all tx DMA buffers.
4754 * If count is zero (cleared by DMA controller after read),
4755 * the buffer is complete or is actively being read from.
4756 *
4757 * Record buf_count of last buffer with zero count starting
4758 * from current ring position. buf_count is mirror
4759 * copy of count and is not cleared by serial controller.
4760 * If DMA controller is active, that buffer is actively
4761 * being read so add to total.
4762 */
4763 do {
4764 count = desc_count(info->tbufs[i]);
4765 if (count)
4766 total_count += count;
4767 else if (!total_count)
4768 active_buf_count = info->tbufs[i].buf_count;
4769 if (++i == info->tbuf_count)
4770 i = 0;
4771 } while (i != info->tbuf_current);
4772
4773 /* read tx DMA status register */
4774 reg_value = rd_reg32(info, TDCSR);
4775
4776 /* if tx DMA active, last zero count buffer is in use */
4777 if (reg_value & BIT0)
4778 total_count += active_buf_count;
4779
4780 /* add tx FIFO count = reg_value[15..8] */
4781 total_count += (reg_value >> 8) & 0xff;
4782
4783 /* if transmitter active add one byte for shift register */
4784 if (info->tx_active)
4785 total_count++;
4786
4787 return total_count;
4788}
4789
4790/*
4791 * load data into transmit DMA buffer ring and start transmitter if needed
4792 * return true if data accepted, otherwise false (buffers full)
4793 */
4794static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4795{
4796 unsigned short count;
4797 unsigned int i;
4798 struct slgt_desc *d;
4799
4800 /* check required buffer space */
4801 if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4802 return false;
4803
4804 DBGDATA(info, buf, size, "tx");
4805
4806 /*
4807 * copy data to one or more DMA buffers in circular ring
4808 * tbuf_start = first buffer for this data
4809 * tbuf_current = next free buffer
4810 *
4811 * Copy all data before making data visible to DMA controller by
4812 * setting descriptor count of the first buffer.
4813 * This prevents an active DMA controller from reading the first DMA
4814 * buffers of a frame and stopping before the final buffers are filled.
4815 */
4816
4817 info->tbuf_start = i = info->tbuf_current;
4818
4819 while (size) {
4820 d = &info->tbufs[i];
4821
4822 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4823 memcpy(d->buf, buf, count);
4824
4825 size -= count;
4826 buf += count;
4827
4828 /*
4829 * set EOF bit for last buffer of HDLC frame or
4830 * for every buffer in raw mode
4831 */
4832 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4833 info->params.mode == MGSL_MODE_RAW)
4834 set_desc_eof(*d, 1);
4835 else
4836 set_desc_eof(*d, 0);
4837
4838 /* set descriptor count for all but first buffer */
4839 if (i != info->tbuf_start)
4840 set_desc_count(*d, count);
4841 d->buf_count = count;
4842
4843 if (++i == info->tbuf_count)
4844 i = 0;
4845 }
4846
4847 info->tbuf_current = i;
4848
4849 /* set first buffer count to make new data visible to DMA controller */
4850 d = &info->tbufs[info->tbuf_start];
4851 set_desc_count(*d, d->buf_count);
4852
4853 /* start transmitter if needed and update transmit timeout */
4854 if (!info->tx_active)
4855 tx_start(info);
4856 update_tx_timer(info);
4857
4858 return true;
4859}
4860
4861static int register_test(struct slgt_info *info)
4862{
4863 static unsigned short patterns[] =
4864 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4865 static unsigned int count = ARRAY_SIZE(patterns);
4866 unsigned int i;
4867 int rc = 0;
4868
4869 for (i=0 ; i < count ; i++) {
4870 wr_reg16(info, TIR, patterns[i]);
4871 wr_reg16(info, BDR, patterns[(i+1)%count]);
4872 if ((rd_reg16(info, TIR) != patterns[i]) ||
4873 (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4874 rc = -ENODEV;
4875 break;
4876 }
4877 }
4878 info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4879 info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4880 return rc;
4881}
4882
4883static int irq_test(struct slgt_info *info)
4884{
4885 unsigned long timeout;
4886 unsigned long flags;
4887 struct tty_struct *oldtty = info->port.tty;
4888 u32 speed = info->params.data_rate;
4889
4890 info->params.data_rate = 921600;
4891 info->port.tty = NULL;
4892
4893 spin_lock_irqsave(&info->lock, flags);
4894 async_mode(info);
4895 slgt_irq_on(info, IRQ_TXIDLE);
4896
4897 /* enable transmitter */
4898 wr_reg16(info, TCR,
4899 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4900
4901 /* write one byte and wait for tx idle */
4902 wr_reg16(info, TDR, 0);
4903
4904 /* assume failure */
4905 info->init_error = DiagStatus_IrqFailure;
4906 info->irq_occurred = false;
4907
4908 spin_unlock_irqrestore(&info->lock, flags);
4909
4910 timeout=100;
4911 while(timeout-- && !info->irq_occurred)
4912 msleep_interruptible(10);
4913
4914 spin_lock_irqsave(&info->lock,flags);
4915 reset_port(info);
4916 spin_unlock_irqrestore(&info->lock,flags);
4917
4918 info->params.data_rate = speed;
4919 info->port.tty = oldtty;
4920
4921 info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4922 return info->irq_occurred ? 0 : -ENODEV;
4923}
4924
4925static int loopback_test_rx(struct slgt_info *info)
4926{
4927 unsigned char *src, *dest;
4928 int count;
4929
4930 if (desc_complete(info->rbufs[0])) {
4931 count = desc_count(info->rbufs[0]);
4932 src = info->rbufs[0].buf;
4933 dest = info->tmp_rbuf;
4934
4935 for( ; count ; count-=2, src+=2) {
4936 /* src=data byte (src+1)=status byte */
4937 if (!(*(src+1) & (BIT9 + BIT8))) {
4938 *dest = *src;
4939 dest++;
4940 info->tmp_rbuf_count++;
4941 }
4942 }
4943 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4944 return 1;
4945 }
4946 return 0;
4947}
4948
4949static int loopback_test(struct slgt_info *info)
4950{
4951#define TESTFRAMESIZE 20
4952
4953 unsigned long timeout;
4954 u16 count;
4955 unsigned char buf[TESTFRAMESIZE];
4956 int rc = -ENODEV;
4957 unsigned long flags;
4958
4959 struct tty_struct *oldtty = info->port.tty;
4960 MGSL_PARAMS params;
4961
4962 memcpy(¶ms, &info->params, sizeof(params));
4963
4964 info->params.mode = MGSL_MODE_ASYNC;
4965 info->params.data_rate = 921600;
4966 info->params.loopback = 1;
4967 info->port.tty = NULL;
4968
4969 /* build and send transmit frame */
4970 for (count = 0; count < TESTFRAMESIZE; ++count)
4971 buf[count] = (unsigned char)count;
4972
4973 info->tmp_rbuf_count = 0;
4974 memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4975
4976 /* program hardware for HDLC and enabled receiver */
4977 spin_lock_irqsave(&info->lock,flags);
4978 async_mode(info);
4979 rx_start(info);
4980 tx_load(info, buf, count);
4981 spin_unlock_irqrestore(&info->lock, flags);
4982
4983 /* wait for receive complete */
4984 for (timeout = 100; timeout; --timeout) {
4985 msleep_interruptible(10);
4986 if (loopback_test_rx(info)) {
4987 rc = 0;
4988 break;
4989 }
4990 }
4991
4992 /* verify received frame length and contents */
4993 if (!rc && (info->tmp_rbuf_count != count ||
4994 memcmp(buf, info->tmp_rbuf, count))) {
4995 rc = -ENODEV;
4996 }
4997
4998 spin_lock_irqsave(&info->lock,flags);
4999 reset_adapter(info);
5000 spin_unlock_irqrestore(&info->lock,flags);
5001
5002 memcpy(&info->params, ¶ms, sizeof(info->params));
5003 info->port.tty = oldtty;
5004
5005 info->init_error = rc ? DiagStatus_DmaFailure : 0;
5006 return rc;
5007}
5008
5009static int adapter_test(struct slgt_info *info)
5010{
5011 DBGINFO(("testing %s\n", info->device_name));
5012 if (register_test(info) < 0) {
5013 printk("register test failure %s addr=%08X\n",
5014 info->device_name, info->phys_reg_addr);
5015 } else if (irq_test(info) < 0) {
5016 printk("IRQ test failure %s IRQ=%d\n",
5017 info->device_name, info->irq_level);
5018 } else if (loopback_test(info) < 0) {
5019 printk("loopback test failure %s\n", info->device_name);
5020 }
5021 return info->init_error;
5022}
5023
5024/*
5025 * transmit timeout handler
5026 */
5027static void tx_timeout(struct timer_list *t)
5028{
5029 struct slgt_info *info = from_timer(info, t, tx_timer);
5030 unsigned long flags;
5031
5032 DBGINFO(("%s tx_timeout\n", info->device_name));
5033 if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5034 info->icount.txtimeout++;
5035 }
5036 spin_lock_irqsave(&info->lock,flags);
5037 tx_stop(info);
5038 spin_unlock_irqrestore(&info->lock,flags);
5039
5040#if SYNCLINK_GENERIC_HDLC
5041 if (info->netcount)
5042 hdlcdev_tx_done(info);
5043 else
5044#endif
5045 bh_transmit(info);
5046}
5047
5048/*
5049 * receive buffer polling timer
5050 */
5051static void rx_timeout(struct timer_list *t)
5052{
5053 struct slgt_info *info = from_timer(info, t, rx_timer);
5054 unsigned long flags;
5055
5056 DBGINFO(("%s rx_timeout\n", info->device_name));
5057 spin_lock_irqsave(&info->lock, flags);
5058 info->pending_bh |= BH_RECEIVE;
5059 spin_unlock_irqrestore(&info->lock, flags);
5060 bh_handler(&info->task);
5061}
5062