Loading...
1// SPDX-License-Identifier: GPL-2.0
2/* sunzilog.c: Zilog serial driver for Sparc systems.
3 *
4 * Driver for Zilog serial chips found on Sun workstations and
5 * servers. This driver could actually be made more generic.
6 *
7 * This is based on the old drivers/sbus/char/zs.c code. A lot
8 * of code has been simply moved over directly from there but
9 * much has been rewritten. Credits therefore go out to Eddie
10 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their
11 * work there.
12 *
13 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net)
14 */
15
16#include <linux/module.h>
17#include <linux/kernel.h>
18#include <linux/errno.h>
19#include <linux/delay.h>
20#include <linux/tty.h>
21#include <linux/tty_flip.h>
22#include <linux/major.h>
23#include <linux/string.h>
24#include <linux/ptrace.h>
25#include <linux/ioport.h>
26#include <linux/slab.h>
27#include <linux/circ_buf.h>
28#include <linux/serial.h>
29#include <linux/sysrq.h>
30#include <linux/console.h>
31#include <linux/spinlock.h>
32#ifdef CONFIG_SERIO
33#include <linux/serio.h>
34#endif
35#include <linux/init.h>
36#include <linux/of_device.h>
37
38#include <asm/io.h>
39#include <asm/irq.h>
40#include <asm/prom.h>
41#include <asm/setup.h>
42
43#if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
44#define SUPPORT_SYSRQ
45#endif
46
47#include <linux/serial_core.h>
48#include <linux/sunserialcore.h>
49
50#include "sunzilog.h"
51
52/* On 32-bit sparcs we need to delay after register accesses
53 * to accommodate sun4 systems, but we do not need to flush writes.
54 * On 64-bit sparc we only need to flush single writes to ensure
55 * completion.
56 */
57#ifndef CONFIG_SPARC64
58#define ZSDELAY() udelay(5)
59#define ZSDELAY_LONG() udelay(20)
60#define ZS_WSYNC(channel) do { } while (0)
61#else
62#define ZSDELAY()
63#define ZSDELAY_LONG()
64#define ZS_WSYNC(__channel) \
65 readb(&((__channel)->control))
66#endif
67
68#define ZS_CLOCK 4915200 /* Zilog input clock rate. */
69#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
70
71/*
72 * We wrap our port structure around the generic uart_port.
73 */
74struct uart_sunzilog_port {
75 struct uart_port port;
76
77 /* IRQ servicing chain. */
78 struct uart_sunzilog_port *next;
79
80 /* Current values of Zilog write registers. */
81 unsigned char curregs[NUM_ZSREGS];
82
83 unsigned int flags;
84#define SUNZILOG_FLAG_CONS_KEYB 0x00000001
85#define SUNZILOG_FLAG_CONS_MOUSE 0x00000002
86#define SUNZILOG_FLAG_IS_CONS 0x00000004
87#define SUNZILOG_FLAG_IS_KGDB 0x00000008
88#define SUNZILOG_FLAG_MODEM_STATUS 0x00000010
89#define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020
90#define SUNZILOG_FLAG_REGS_HELD 0x00000040
91#define SUNZILOG_FLAG_TX_STOPPED 0x00000080
92#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100
93#define SUNZILOG_FLAG_ESCC 0x00000200
94#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400
95
96 unsigned int cflag;
97
98 unsigned char parity_mask;
99 unsigned char prev_status;
100
101#ifdef CONFIG_SERIO
102 struct serio serio;
103 int serio_open;
104#endif
105};
106
107static void sunzilog_putchar(struct uart_port *port, int ch);
108
109#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
110#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT))
111
112#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB)
113#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE)
114#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS)
115#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB)
116#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
117#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A)
118#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD)
119#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED)
120#define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE)
121
122/* Reading and writing Zilog8530 registers. The delays are to make this
123 * driver work on the Sun4 which needs a settling delay after each chip
124 * register access, other machines handle this in hardware via auxiliary
125 * flip-flops which implement the settle time we do in software.
126 *
127 * The port lock must be held and local IRQs must be disabled
128 * when {read,write}_zsreg is invoked.
129 */
130static unsigned char read_zsreg(struct zilog_channel __iomem *channel,
131 unsigned char reg)
132{
133 unsigned char retval;
134
135 writeb(reg, &channel->control);
136 ZSDELAY();
137 retval = readb(&channel->control);
138 ZSDELAY();
139
140 return retval;
141}
142
143static void write_zsreg(struct zilog_channel __iomem *channel,
144 unsigned char reg, unsigned char value)
145{
146 writeb(reg, &channel->control);
147 ZSDELAY();
148 writeb(value, &channel->control);
149 ZSDELAY();
150}
151
152static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
153{
154 int i;
155
156 for (i = 0; i < 32; i++) {
157 unsigned char regval;
158
159 regval = readb(&channel->control);
160 ZSDELAY();
161 if (regval & Rx_CH_AV)
162 break;
163
164 regval = read_zsreg(channel, R1);
165 readb(&channel->data);
166 ZSDELAY();
167
168 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
169 writeb(ERR_RES, &channel->control);
170 ZSDELAY();
171 ZS_WSYNC(channel);
172 }
173 }
174}
175
176/* This function must only be called when the TX is not busy. The UART
177 * port lock must be held and local interrupts disabled.
178 */
179static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
180{
181 int i;
182 int escc;
183 unsigned char r15;
184
185 /* Let pending transmits finish. */
186 for (i = 0; i < 1000; i++) {
187 unsigned char stat = read_zsreg(channel, R1);
188 if (stat & ALL_SNT)
189 break;
190 udelay(100);
191 }
192
193 writeb(ERR_RES, &channel->control);
194 ZSDELAY();
195 ZS_WSYNC(channel);
196
197 sunzilog_clear_fifo(channel);
198
199 /* Disable all interrupts. */
200 write_zsreg(channel, R1,
201 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
202
203 /* Set parity, sync config, stop bits, and clock divisor. */
204 write_zsreg(channel, R4, regs[R4]);
205
206 /* Set misc. TX/RX control bits. */
207 write_zsreg(channel, R10, regs[R10]);
208
209 /* Set TX/RX controls sans the enable bits. */
210 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
211 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
212
213 /* Synchronous mode config. */
214 write_zsreg(channel, R6, regs[R6]);
215 write_zsreg(channel, R7, regs[R7]);
216
217 /* Don't mess with the interrupt vector (R2, unused by us) and
218 * master interrupt control (R9). We make sure this is setup
219 * properly at probe time then never touch it again.
220 */
221
222 /* Disable baud generator. */
223 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
224
225 /* Clock mode control. */
226 write_zsreg(channel, R11, regs[R11]);
227
228 /* Lower and upper byte of baud rate generator divisor. */
229 write_zsreg(channel, R12, regs[R12]);
230 write_zsreg(channel, R13, regs[R13]);
231
232 /* Now rewrite R14, with BRENAB (if set). */
233 write_zsreg(channel, R14, regs[R14]);
234
235 /* External status interrupt control. */
236 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN);
237
238 /* ESCC Extension Register */
239 r15 = read_zsreg(channel, R15);
240 if (r15 & 0x01) {
241 write_zsreg(channel, R7, regs[R7p]);
242
243 /* External status interrupt and FIFO control. */
244 write_zsreg(channel, R15, regs[R15] & ~WR7pEN);
245 escc = 1;
246 } else {
247 /* Clear FIFO bit case it is an issue */
248 regs[R15] &= ~FIFOEN;
249 escc = 0;
250 }
251
252 /* Reset external status interrupts. */
253 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */
254 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */
255
256 /* Rewrite R3/R5, this time without enables masked. */
257 write_zsreg(channel, R3, regs[R3]);
258 write_zsreg(channel, R5, regs[R5]);
259
260 /* Rewrite R1, this time without IRQ enabled masked. */
261 write_zsreg(channel, R1, regs[R1]);
262
263 return escc;
264}
265
266/* Reprogram the Zilog channel HW registers with the copies found in the
267 * software state struct. If the transmitter is busy, we defer this update
268 * until the next TX complete interrupt. Else, we do it right now.
269 *
270 * The UART port lock must be held and local interrupts disabled.
271 */
272static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up,
273 struct zilog_channel __iomem *channel)
274{
275 if (!ZS_REGS_HELD(up)) {
276 if (ZS_TX_ACTIVE(up)) {
277 up->flags |= SUNZILOG_FLAG_REGS_HELD;
278 } else {
279 __load_zsregs(channel, up->curregs);
280 }
281 }
282}
283
284static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up)
285{
286 unsigned int cur_cflag = up->cflag;
287 int brg, new_baud;
288
289 up->cflag &= ~CBAUD;
290 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
291
292 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
293 up->curregs[R12] = (brg & 0xff);
294 up->curregs[R13] = (brg >> 8) & 0xff;
295 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port));
296}
297
298static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
299 unsigned char ch, int is_break)
300{
301 if (ZS_IS_KEYB(up)) {
302 /* Stop-A is handled by drivers/char/keyboard.c now. */
303#ifdef CONFIG_SERIO
304 if (up->serio_open)
305 serio_interrupt(&up->serio, ch, 0);
306#endif
307 } else if (ZS_IS_MOUSE(up)) {
308 int ret = suncore_mouse_baud_detection(ch, is_break);
309
310 switch (ret) {
311 case 2:
312 sunzilog_change_mouse_baud(up);
313 /* fallthru */
314 case 1:
315 break;
316
317 case 0:
318#ifdef CONFIG_SERIO
319 if (up->serio_open)
320 serio_interrupt(&up->serio, ch, 0);
321#endif
322 break;
323 }
324 }
325}
326
327static struct tty_port *
328sunzilog_receive_chars(struct uart_sunzilog_port *up,
329 struct zilog_channel __iomem *channel)
330{
331 struct tty_port *port = NULL;
332 unsigned char ch, r1, flag;
333
334 if (up->port.state != NULL) /* Unopened serial console */
335 port = &up->port.state->port;
336
337 for (;;) {
338
339 r1 = read_zsreg(channel, R1);
340 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
341 writeb(ERR_RES, &channel->control);
342 ZSDELAY();
343 ZS_WSYNC(channel);
344 }
345
346 ch = readb(&channel->control);
347 ZSDELAY();
348
349 /* This funny hack depends upon BRK_ABRT not interfering
350 * with the other bits we care about in R1.
351 */
352 if (ch & BRK_ABRT)
353 r1 |= BRK_ABRT;
354
355 if (!(ch & Rx_CH_AV))
356 break;
357
358 ch = readb(&channel->data);
359 ZSDELAY();
360
361 ch &= up->parity_mask;
362
363 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) {
364 sunzilog_kbdms_receive_chars(up, ch, 0);
365 continue;
366 }
367
368 /* A real serial line, record the character and status. */
369 flag = TTY_NORMAL;
370 up->port.icount.rx++;
371 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
372 if (r1 & BRK_ABRT) {
373 r1 &= ~(PAR_ERR | CRC_ERR);
374 up->port.icount.brk++;
375 if (uart_handle_break(&up->port))
376 continue;
377 }
378 else if (r1 & PAR_ERR)
379 up->port.icount.parity++;
380 else if (r1 & CRC_ERR)
381 up->port.icount.frame++;
382 if (r1 & Rx_OVR)
383 up->port.icount.overrun++;
384 r1 &= up->port.read_status_mask;
385 if (r1 & BRK_ABRT)
386 flag = TTY_BREAK;
387 else if (r1 & PAR_ERR)
388 flag = TTY_PARITY;
389 else if (r1 & CRC_ERR)
390 flag = TTY_FRAME;
391 }
392 if (uart_handle_sysrq_char(&up->port, ch) || !port)
393 continue;
394
395 if (up->port.ignore_status_mask == 0xff ||
396 (r1 & up->port.ignore_status_mask) == 0) {
397 tty_insert_flip_char(port, ch, flag);
398 }
399 if (r1 & Rx_OVR)
400 tty_insert_flip_char(port, 0, TTY_OVERRUN);
401 }
402
403 return port;
404}
405
406static void sunzilog_status_handle(struct uart_sunzilog_port *up,
407 struct zilog_channel __iomem *channel)
408{
409 unsigned char status;
410
411 status = readb(&channel->control);
412 ZSDELAY();
413
414 writeb(RES_EXT_INT, &channel->control);
415 ZSDELAY();
416 ZS_WSYNC(channel);
417
418 if (status & BRK_ABRT) {
419 if (ZS_IS_MOUSE(up))
420 sunzilog_kbdms_receive_chars(up, 0, 1);
421 if (ZS_IS_CONS(up)) {
422 /* Wait for BREAK to deassert to avoid potentially
423 * confusing the PROM.
424 */
425 while (1) {
426 status = readb(&channel->control);
427 ZSDELAY();
428 if (!(status & BRK_ABRT))
429 break;
430 }
431 sun_do_break();
432 return;
433 }
434 }
435
436 if (ZS_WANTS_MODEM_STATUS(up)) {
437 if (status & SYNC)
438 up->port.icount.dsr++;
439
440 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
441 * But it does not tell us which bit has changed, we have to keep
442 * track of this ourselves.
443 */
444 if ((status ^ up->prev_status) ^ DCD)
445 uart_handle_dcd_change(&up->port,
446 (status & DCD));
447 if ((status ^ up->prev_status) ^ CTS)
448 uart_handle_cts_change(&up->port,
449 (status & CTS));
450
451 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
452 }
453
454 up->prev_status = status;
455}
456
457static void sunzilog_transmit_chars(struct uart_sunzilog_port *up,
458 struct zilog_channel __iomem *channel)
459{
460 struct circ_buf *xmit;
461
462 if (ZS_IS_CONS(up)) {
463 unsigned char status = readb(&channel->control);
464 ZSDELAY();
465
466 /* TX still busy? Just wait for the next TX done interrupt.
467 *
468 * It can occur because of how we do serial console writes. It would
469 * be nice to transmit console writes just like we normally would for
470 * a TTY line. (ie. buffered and TX interrupt driven). That is not
471 * easy because console writes cannot sleep. One solution might be
472 * to poll on enough port->xmit space becoming free. -DaveM
473 */
474 if (!(status & Tx_BUF_EMP))
475 return;
476 }
477
478 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE;
479
480 if (ZS_REGS_HELD(up)) {
481 __load_zsregs(channel, up->curregs);
482 up->flags &= ~SUNZILOG_FLAG_REGS_HELD;
483 }
484
485 if (ZS_TX_STOPPED(up)) {
486 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
487 goto ack_tx_int;
488 }
489
490 if (up->port.x_char) {
491 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
492 writeb(up->port.x_char, &channel->data);
493 ZSDELAY();
494 ZS_WSYNC(channel);
495
496 up->port.icount.tx++;
497 up->port.x_char = 0;
498 return;
499 }
500
501 if (up->port.state == NULL)
502 goto ack_tx_int;
503 xmit = &up->port.state->xmit;
504 if (uart_circ_empty(xmit))
505 goto ack_tx_int;
506
507 if (uart_tx_stopped(&up->port))
508 goto ack_tx_int;
509
510 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
511 writeb(xmit->buf[xmit->tail], &channel->data);
512 ZSDELAY();
513 ZS_WSYNC(channel);
514
515 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
516 up->port.icount.tx++;
517
518 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
519 uart_write_wakeup(&up->port);
520
521 return;
522
523ack_tx_int:
524 writeb(RES_Tx_P, &channel->control);
525 ZSDELAY();
526 ZS_WSYNC(channel);
527}
528
529static irqreturn_t sunzilog_interrupt(int irq, void *dev_id)
530{
531 struct uart_sunzilog_port *up = dev_id;
532
533 while (up) {
534 struct zilog_channel __iomem *channel
535 = ZILOG_CHANNEL_FROM_PORT(&up->port);
536 struct tty_port *port;
537 unsigned char r3;
538
539 spin_lock(&up->port.lock);
540 r3 = read_zsreg(channel, R3);
541
542 /* Channel A */
543 port = NULL;
544 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
545 writeb(RES_H_IUS, &channel->control);
546 ZSDELAY();
547 ZS_WSYNC(channel);
548
549 if (r3 & CHARxIP)
550 port = sunzilog_receive_chars(up, channel);
551 if (r3 & CHAEXT)
552 sunzilog_status_handle(up, channel);
553 if (r3 & CHATxIP)
554 sunzilog_transmit_chars(up, channel);
555 }
556 spin_unlock(&up->port.lock);
557
558 if (port)
559 tty_flip_buffer_push(port);
560
561 /* Channel B */
562 up = up->next;
563 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
564
565 spin_lock(&up->port.lock);
566 port = NULL;
567 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
568 writeb(RES_H_IUS, &channel->control);
569 ZSDELAY();
570 ZS_WSYNC(channel);
571
572 if (r3 & CHBRxIP)
573 port = sunzilog_receive_chars(up, channel);
574 if (r3 & CHBEXT)
575 sunzilog_status_handle(up, channel);
576 if (r3 & CHBTxIP)
577 sunzilog_transmit_chars(up, channel);
578 }
579 spin_unlock(&up->port.lock);
580
581 if (port)
582 tty_flip_buffer_push(port);
583
584 up = up->next;
585 }
586
587 return IRQ_HANDLED;
588}
589
590/* A convenient way to quickly get R0 status. The caller must _not_ hold the
591 * port lock, it is acquired here.
592 */
593static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
594{
595 struct zilog_channel __iomem *channel;
596 unsigned char status;
597
598 channel = ZILOG_CHANNEL_FROM_PORT(port);
599 status = readb(&channel->control);
600 ZSDELAY();
601
602 return status;
603}
604
605/* The port lock is not held. */
606static unsigned int sunzilog_tx_empty(struct uart_port *port)
607{
608 unsigned long flags;
609 unsigned char status;
610 unsigned int ret;
611
612 spin_lock_irqsave(&port->lock, flags);
613
614 status = sunzilog_read_channel_status(port);
615
616 spin_unlock_irqrestore(&port->lock, flags);
617
618 if (status & Tx_BUF_EMP)
619 ret = TIOCSER_TEMT;
620 else
621 ret = 0;
622
623 return ret;
624}
625
626/* The port lock is held and interrupts are disabled. */
627static unsigned int sunzilog_get_mctrl(struct uart_port *port)
628{
629 unsigned char status;
630 unsigned int ret;
631
632 status = sunzilog_read_channel_status(port);
633
634 ret = 0;
635 if (status & DCD)
636 ret |= TIOCM_CAR;
637 if (status & SYNC)
638 ret |= TIOCM_DSR;
639 if (status & CTS)
640 ret |= TIOCM_CTS;
641
642 return ret;
643}
644
645/* The port lock is held and interrupts are disabled. */
646static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
647{
648 struct uart_sunzilog_port *up =
649 container_of(port, struct uart_sunzilog_port, port);
650 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
651 unsigned char set_bits, clear_bits;
652
653 set_bits = clear_bits = 0;
654
655 if (mctrl & TIOCM_RTS)
656 set_bits |= RTS;
657 else
658 clear_bits |= RTS;
659 if (mctrl & TIOCM_DTR)
660 set_bits |= DTR;
661 else
662 clear_bits |= DTR;
663
664 /* NOTE: Not subject to 'transmitter active' rule. */
665 up->curregs[R5] |= set_bits;
666 up->curregs[R5] &= ~clear_bits;
667 write_zsreg(channel, R5, up->curregs[R5]);
668}
669
670/* The port lock is held and interrupts are disabled. */
671static void sunzilog_stop_tx(struct uart_port *port)
672{
673 struct uart_sunzilog_port *up =
674 container_of(port, struct uart_sunzilog_port, port);
675
676 up->flags |= SUNZILOG_FLAG_TX_STOPPED;
677}
678
679/* The port lock is held and interrupts are disabled. */
680static void sunzilog_start_tx(struct uart_port *port)
681{
682 struct uart_sunzilog_port *up =
683 container_of(port, struct uart_sunzilog_port, port);
684 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
685 unsigned char status;
686
687 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
688 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
689
690 status = readb(&channel->control);
691 ZSDELAY();
692
693 /* TX busy? Just wait for the TX done interrupt. */
694 if (!(status & Tx_BUF_EMP))
695 return;
696
697 /* Send the first character to jump-start the TX done
698 * IRQ sending engine.
699 */
700 if (port->x_char) {
701 writeb(port->x_char, &channel->data);
702 ZSDELAY();
703 ZS_WSYNC(channel);
704
705 port->icount.tx++;
706 port->x_char = 0;
707 } else {
708 struct circ_buf *xmit = &port->state->xmit;
709
710 if (uart_circ_empty(xmit))
711 return;
712 writeb(xmit->buf[xmit->tail], &channel->data);
713 ZSDELAY();
714 ZS_WSYNC(channel);
715
716 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
717 port->icount.tx++;
718
719 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
720 uart_write_wakeup(&up->port);
721 }
722}
723
724/* The port lock is held. */
725static void sunzilog_stop_rx(struct uart_port *port)
726{
727 struct uart_sunzilog_port *up = UART_ZILOG(port);
728 struct zilog_channel __iomem *channel;
729
730 if (ZS_IS_CONS(up))
731 return;
732
733 channel = ZILOG_CHANNEL_FROM_PORT(port);
734
735 /* Disable all RX interrupts. */
736 up->curregs[R1] &= ~RxINT_MASK;
737 sunzilog_maybe_update_regs(up, channel);
738}
739
740/* The port lock is held. */
741static void sunzilog_enable_ms(struct uart_port *port)
742{
743 struct uart_sunzilog_port *up =
744 container_of(port, struct uart_sunzilog_port, port);
745 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
746 unsigned char new_reg;
747
748 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
749 if (new_reg != up->curregs[R15]) {
750 up->curregs[R15] = new_reg;
751
752 /* NOTE: Not subject to 'transmitter active' rule. */
753 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
754 }
755}
756
757/* The port lock is not held. */
758static void sunzilog_break_ctl(struct uart_port *port, int break_state)
759{
760 struct uart_sunzilog_port *up =
761 container_of(port, struct uart_sunzilog_port, port);
762 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
763 unsigned char set_bits, clear_bits, new_reg;
764 unsigned long flags;
765
766 set_bits = clear_bits = 0;
767
768 if (break_state)
769 set_bits |= SND_BRK;
770 else
771 clear_bits |= SND_BRK;
772
773 spin_lock_irqsave(&port->lock, flags);
774
775 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
776 if (new_reg != up->curregs[R5]) {
777 up->curregs[R5] = new_reg;
778
779 /* NOTE: Not subject to 'transmitter active' rule. */
780 write_zsreg(channel, R5, up->curregs[R5]);
781 }
782
783 spin_unlock_irqrestore(&port->lock, flags);
784}
785
786static void __sunzilog_startup(struct uart_sunzilog_port *up)
787{
788 struct zilog_channel __iomem *channel;
789
790 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
791 up->prev_status = readb(&channel->control);
792
793 /* Enable receiver and transmitter. */
794 up->curregs[R3] |= RxENAB;
795 up->curregs[R5] |= TxENAB;
796
797 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
798 sunzilog_maybe_update_regs(up, channel);
799}
800
801static int sunzilog_startup(struct uart_port *port)
802{
803 struct uart_sunzilog_port *up = UART_ZILOG(port);
804 unsigned long flags;
805
806 if (ZS_IS_CONS(up))
807 return 0;
808
809 spin_lock_irqsave(&port->lock, flags);
810 __sunzilog_startup(up);
811 spin_unlock_irqrestore(&port->lock, flags);
812 return 0;
813}
814
815/*
816 * The test for ZS_IS_CONS is explained by the following e-mail:
817 *****
818 * From: Russell King <rmk@arm.linux.org.uk>
819 * Date: Sun, 8 Dec 2002 10:18:38 +0000
820 *
821 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
822 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
823 * > and I noticed that something is not right with reference
824 * > counting in this case. It seems that when the console
825 * > is open by kernel initially, this is not accounted
826 * > as an open, and uart_startup is not called.
827 *
828 * That is correct. We are unable to call uart_startup when the serial
829 * console is initialised because it may need to allocate memory (as
830 * request_irq does) and the memory allocators may not have been
831 * initialised.
832 *
833 * 1. initialise the port into a state where it can send characters in the
834 * console write method.
835 *
836 * 2. don't do the actual hardware shutdown in your shutdown() method (but
837 * do the normal software shutdown - ie, free irqs etc)
838 *****
839 */
840static void sunzilog_shutdown(struct uart_port *port)
841{
842 struct uart_sunzilog_port *up = UART_ZILOG(port);
843 struct zilog_channel __iomem *channel;
844 unsigned long flags;
845
846 if (ZS_IS_CONS(up))
847 return;
848
849 spin_lock_irqsave(&port->lock, flags);
850
851 channel = ZILOG_CHANNEL_FROM_PORT(port);
852
853 /* Disable receiver and transmitter. */
854 up->curregs[R3] &= ~RxENAB;
855 up->curregs[R5] &= ~TxENAB;
856
857 /* Disable all interrupts and BRK assertion. */
858 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
859 up->curregs[R5] &= ~SND_BRK;
860 sunzilog_maybe_update_regs(up, channel);
861
862 spin_unlock_irqrestore(&port->lock, flags);
863}
864
865/* Shared by TTY driver and serial console setup. The port lock is held
866 * and local interrupts are disabled.
867 */
868static void
869sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag,
870 unsigned int iflag, int brg)
871{
872
873 up->curregs[R10] = NRZ;
874 up->curregs[R11] = TCBR | RCBR;
875
876 /* Program BAUD and clock source. */
877 up->curregs[R4] &= ~XCLK_MASK;
878 up->curregs[R4] |= X16CLK;
879 up->curregs[R12] = brg & 0xff;
880 up->curregs[R13] = (brg >> 8) & 0xff;
881 up->curregs[R14] = BRSRC | BRENAB;
882
883 /* Character size, stop bits, and parity. */
884 up->curregs[R3] &= ~RxN_MASK;
885 up->curregs[R5] &= ~TxN_MASK;
886 switch (cflag & CSIZE) {
887 case CS5:
888 up->curregs[R3] |= Rx5;
889 up->curregs[R5] |= Tx5;
890 up->parity_mask = 0x1f;
891 break;
892 case CS6:
893 up->curregs[R3] |= Rx6;
894 up->curregs[R5] |= Tx6;
895 up->parity_mask = 0x3f;
896 break;
897 case CS7:
898 up->curregs[R3] |= Rx7;
899 up->curregs[R5] |= Tx7;
900 up->parity_mask = 0x7f;
901 break;
902 case CS8:
903 default:
904 up->curregs[R3] |= Rx8;
905 up->curregs[R5] |= Tx8;
906 up->parity_mask = 0xff;
907 break;
908 }
909 up->curregs[R4] &= ~0x0c;
910 if (cflag & CSTOPB)
911 up->curregs[R4] |= SB2;
912 else
913 up->curregs[R4] |= SB1;
914 if (cflag & PARENB)
915 up->curregs[R4] |= PAR_ENAB;
916 else
917 up->curregs[R4] &= ~PAR_ENAB;
918 if (!(cflag & PARODD))
919 up->curregs[R4] |= PAR_EVEN;
920 else
921 up->curregs[R4] &= ~PAR_EVEN;
922
923 up->port.read_status_mask = Rx_OVR;
924 if (iflag & INPCK)
925 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
926 if (iflag & (IGNBRK | BRKINT | PARMRK))
927 up->port.read_status_mask |= BRK_ABRT;
928
929 up->port.ignore_status_mask = 0;
930 if (iflag & IGNPAR)
931 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
932 if (iflag & IGNBRK) {
933 up->port.ignore_status_mask |= BRK_ABRT;
934 if (iflag & IGNPAR)
935 up->port.ignore_status_mask |= Rx_OVR;
936 }
937
938 if ((cflag & CREAD) == 0)
939 up->port.ignore_status_mask = 0xff;
940}
941
942/* The port lock is not held. */
943static void
944sunzilog_set_termios(struct uart_port *port, struct ktermios *termios,
945 struct ktermios *old)
946{
947 struct uart_sunzilog_port *up =
948 container_of(port, struct uart_sunzilog_port, port);
949 unsigned long flags;
950 int baud, brg;
951
952 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
953
954 spin_lock_irqsave(&up->port.lock, flags);
955
956 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
957
958 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
959
960 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
961 up->flags |= SUNZILOG_FLAG_MODEM_STATUS;
962 else
963 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS;
964
965 up->cflag = termios->c_cflag;
966
967 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
968
969 uart_update_timeout(port, termios->c_cflag, baud);
970
971 spin_unlock_irqrestore(&up->port.lock, flags);
972}
973
974static const char *sunzilog_type(struct uart_port *port)
975{
976 struct uart_sunzilog_port *up = UART_ZILOG(port);
977
978 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs";
979}
980
981/* We do not request/release mappings of the registers here, this
982 * happens at early serial probe time.
983 */
984static void sunzilog_release_port(struct uart_port *port)
985{
986}
987
988static int sunzilog_request_port(struct uart_port *port)
989{
990 return 0;
991}
992
993/* These do not need to do anything interesting either. */
994static void sunzilog_config_port(struct uart_port *port, int flags)
995{
996}
997
998/* We do not support letting the user mess with the divisor, IRQ, etc. */
999static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
1000{
1001 return -EINVAL;
1002}
1003
1004#ifdef CONFIG_CONSOLE_POLL
1005static int sunzilog_get_poll_char(struct uart_port *port)
1006{
1007 unsigned char ch, r1;
1008 struct uart_sunzilog_port *up =
1009 container_of(port, struct uart_sunzilog_port, port);
1010 struct zilog_channel __iomem *channel
1011 = ZILOG_CHANNEL_FROM_PORT(&up->port);
1012
1013
1014 r1 = read_zsreg(channel, R1);
1015 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
1016 writeb(ERR_RES, &channel->control);
1017 ZSDELAY();
1018 ZS_WSYNC(channel);
1019 }
1020
1021 ch = readb(&channel->control);
1022 ZSDELAY();
1023
1024 /* This funny hack depends upon BRK_ABRT not interfering
1025 * with the other bits we care about in R1.
1026 */
1027 if (ch & BRK_ABRT)
1028 r1 |= BRK_ABRT;
1029
1030 if (!(ch & Rx_CH_AV))
1031 return NO_POLL_CHAR;
1032
1033 ch = readb(&channel->data);
1034 ZSDELAY();
1035
1036 ch &= up->parity_mask;
1037 return ch;
1038}
1039
1040static void sunzilog_put_poll_char(struct uart_port *port,
1041 unsigned char ch)
1042{
1043 struct uart_sunzilog_port *up =
1044 container_of(port, struct uart_sunzilog_port, port);
1045
1046 sunzilog_putchar(&up->port, ch);
1047}
1048#endif /* CONFIG_CONSOLE_POLL */
1049
1050static const struct uart_ops sunzilog_pops = {
1051 .tx_empty = sunzilog_tx_empty,
1052 .set_mctrl = sunzilog_set_mctrl,
1053 .get_mctrl = sunzilog_get_mctrl,
1054 .stop_tx = sunzilog_stop_tx,
1055 .start_tx = sunzilog_start_tx,
1056 .stop_rx = sunzilog_stop_rx,
1057 .enable_ms = sunzilog_enable_ms,
1058 .break_ctl = sunzilog_break_ctl,
1059 .startup = sunzilog_startup,
1060 .shutdown = sunzilog_shutdown,
1061 .set_termios = sunzilog_set_termios,
1062 .type = sunzilog_type,
1063 .release_port = sunzilog_release_port,
1064 .request_port = sunzilog_request_port,
1065 .config_port = sunzilog_config_port,
1066 .verify_port = sunzilog_verify_port,
1067#ifdef CONFIG_CONSOLE_POLL
1068 .poll_get_char = sunzilog_get_poll_char,
1069 .poll_put_char = sunzilog_put_poll_char,
1070#endif
1071};
1072
1073static int uart_chip_count;
1074static struct uart_sunzilog_port *sunzilog_port_table;
1075static struct zilog_layout __iomem **sunzilog_chip_regs;
1076
1077static struct uart_sunzilog_port *sunzilog_irq_chain;
1078
1079static struct uart_driver sunzilog_reg = {
1080 .owner = THIS_MODULE,
1081 .driver_name = "sunzilog",
1082 .dev_name = "ttyS",
1083 .major = TTY_MAJOR,
1084};
1085
1086static int __init sunzilog_alloc_tables(int num_sunzilog)
1087{
1088 struct uart_sunzilog_port *up;
1089 unsigned long size;
1090 int num_channels = num_sunzilog * 2;
1091 int i;
1092
1093 size = num_channels * sizeof(struct uart_sunzilog_port);
1094 sunzilog_port_table = kzalloc(size, GFP_KERNEL);
1095 if (!sunzilog_port_table)
1096 return -ENOMEM;
1097
1098 for (i = 0; i < num_channels; i++) {
1099 up = &sunzilog_port_table[i];
1100
1101 spin_lock_init(&up->port.lock);
1102
1103 if (i == 0)
1104 sunzilog_irq_chain = up;
1105
1106 if (i < num_channels - 1)
1107 up->next = up + 1;
1108 else
1109 up->next = NULL;
1110 }
1111
1112 size = num_sunzilog * sizeof(struct zilog_layout __iomem *);
1113 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL);
1114 if (!sunzilog_chip_regs) {
1115 kfree(sunzilog_port_table);
1116 sunzilog_irq_chain = NULL;
1117 return -ENOMEM;
1118 }
1119
1120 return 0;
1121}
1122
1123static void sunzilog_free_tables(void)
1124{
1125 kfree(sunzilog_port_table);
1126 sunzilog_irq_chain = NULL;
1127 kfree(sunzilog_chip_regs);
1128}
1129
1130#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
1131
1132static void sunzilog_putchar(struct uart_port *port, int ch)
1133{
1134 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
1135 int loops = ZS_PUT_CHAR_MAX_DELAY;
1136
1137 /* This is a timed polling loop so do not switch the explicit
1138 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1139 */
1140 do {
1141 unsigned char val = readb(&channel->control);
1142 if (val & Tx_BUF_EMP) {
1143 ZSDELAY();
1144 break;
1145 }
1146 udelay(5);
1147 } while (--loops);
1148
1149 writeb(ch, &channel->data);
1150 ZSDELAY();
1151 ZS_WSYNC(channel);
1152}
1153
1154#ifdef CONFIG_SERIO
1155
1156static DEFINE_SPINLOCK(sunzilog_serio_lock);
1157
1158static int sunzilog_serio_write(struct serio *serio, unsigned char ch)
1159{
1160 struct uart_sunzilog_port *up = serio->port_data;
1161 unsigned long flags;
1162
1163 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1164
1165 sunzilog_putchar(&up->port, ch);
1166
1167 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1168
1169 return 0;
1170}
1171
1172static int sunzilog_serio_open(struct serio *serio)
1173{
1174 struct uart_sunzilog_port *up = serio->port_data;
1175 unsigned long flags;
1176 int ret;
1177
1178 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1179 if (!up->serio_open) {
1180 up->serio_open = 1;
1181 ret = 0;
1182 } else
1183 ret = -EBUSY;
1184 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1185
1186 return ret;
1187}
1188
1189static void sunzilog_serio_close(struct serio *serio)
1190{
1191 struct uart_sunzilog_port *up = serio->port_data;
1192 unsigned long flags;
1193
1194 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1195 up->serio_open = 0;
1196 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1197}
1198
1199#endif /* CONFIG_SERIO */
1200
1201#ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE
1202static void
1203sunzilog_console_write(struct console *con, const char *s, unsigned int count)
1204{
1205 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1206 unsigned long flags;
1207 int locked = 1;
1208
1209 if (up->port.sysrq || oops_in_progress)
1210 locked = spin_trylock_irqsave(&up->port.lock, flags);
1211 else
1212 spin_lock_irqsave(&up->port.lock, flags);
1213
1214 uart_console_write(&up->port, s, count, sunzilog_putchar);
1215 udelay(2);
1216
1217 if (locked)
1218 spin_unlock_irqrestore(&up->port.lock, flags);
1219}
1220
1221static int __init sunzilog_console_setup(struct console *con, char *options)
1222{
1223 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1224 unsigned long flags;
1225 int baud, brg;
1226
1227 if (up->port.type != PORT_SUNZILOG)
1228 return -1;
1229
1230 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n",
1231 (sunzilog_reg.minor - 64) + con->index, con->index);
1232
1233 /* Get firmware console settings. */
1234 sunserial_console_termios(con, up->port.dev->of_node);
1235
1236 /* Firmware console speed is limited to 150-->38400 baud so
1237 * this hackish cflag thing is OK.
1238 */
1239 switch (con->cflag & CBAUD) {
1240 case B150: baud = 150; break;
1241 case B300: baud = 300; break;
1242 case B600: baud = 600; break;
1243 case B1200: baud = 1200; break;
1244 case B2400: baud = 2400; break;
1245 case B4800: baud = 4800; break;
1246 default: case B9600: baud = 9600; break;
1247 case B19200: baud = 19200; break;
1248 case B38400: baud = 38400; break;
1249 }
1250
1251 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1252
1253 spin_lock_irqsave(&up->port.lock, flags);
1254
1255 up->curregs[R15] |= BRKIE;
1256 sunzilog_convert_to_zs(up, con->cflag, 0, brg);
1257
1258 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1259 __sunzilog_startup(up);
1260
1261 spin_unlock_irqrestore(&up->port.lock, flags);
1262
1263 return 0;
1264}
1265
1266static struct console sunzilog_console_ops = {
1267 .name = "ttyS",
1268 .write = sunzilog_console_write,
1269 .device = uart_console_device,
1270 .setup = sunzilog_console_setup,
1271 .flags = CON_PRINTBUFFER,
1272 .index = -1,
1273 .data = &sunzilog_reg,
1274};
1275
1276static inline struct console *SUNZILOG_CONSOLE(void)
1277{
1278 return &sunzilog_console_ops;
1279}
1280
1281#else
1282#define SUNZILOG_CONSOLE() (NULL)
1283#endif
1284
1285static void sunzilog_init_kbdms(struct uart_sunzilog_port *up)
1286{
1287 int baud, brg;
1288
1289 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1290 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1291 baud = 1200;
1292 } else {
1293 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1294 baud = 4800;
1295 }
1296
1297 up->curregs[R15] |= BRKIE;
1298 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1299 sunzilog_convert_to_zs(up, up->cflag, 0, brg);
1300 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1301 __sunzilog_startup(up);
1302}
1303
1304#ifdef CONFIG_SERIO
1305static void sunzilog_register_serio(struct uart_sunzilog_port *up)
1306{
1307 struct serio *serio = &up->serio;
1308
1309 serio->port_data = up;
1310
1311 serio->id.type = SERIO_RS232;
1312 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1313 serio->id.proto = SERIO_SUNKBD;
1314 strlcpy(serio->name, "zskbd", sizeof(serio->name));
1315 } else {
1316 serio->id.proto = SERIO_SUN;
1317 serio->id.extra = 1;
1318 strlcpy(serio->name, "zsms", sizeof(serio->name));
1319 }
1320 strlcpy(serio->phys,
1321 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ?
1322 "zs/serio0" : "zs/serio1"),
1323 sizeof(serio->phys));
1324
1325 serio->write = sunzilog_serio_write;
1326 serio->open = sunzilog_serio_open;
1327 serio->close = sunzilog_serio_close;
1328 serio->dev.parent = up->port.dev;
1329
1330 serio_register_port(serio);
1331}
1332#endif
1333
1334static void sunzilog_init_hw(struct uart_sunzilog_port *up)
1335{
1336 struct zilog_channel __iomem *channel;
1337 unsigned long flags;
1338 int baud, brg;
1339
1340 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1341
1342 spin_lock_irqsave(&up->port.lock, flags);
1343 if (ZS_IS_CHANNEL_A(up)) {
1344 write_zsreg(channel, R9, FHWRES);
1345 ZSDELAY_LONG();
1346 (void) read_zsreg(channel, R0);
1347 }
1348
1349 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1350 SUNZILOG_FLAG_CONS_MOUSE)) {
1351 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1352 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1353 up->curregs[R3] = RxENAB | Rx8;
1354 up->curregs[R5] = TxENAB | Tx8;
1355 up->curregs[R6] = 0x00; /* SDLC Address */
1356 up->curregs[R7] = 0x7E; /* SDLC Flag */
1357 up->curregs[R9] = NV;
1358 up->curregs[R7p] = 0x00;
1359 sunzilog_init_kbdms(up);
1360 /* Only enable interrupts if an ISR handler available */
1361 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1362 up->curregs[R9] |= MIE;
1363 write_zsreg(channel, R9, up->curregs[R9]);
1364 } else {
1365 /* Normal serial TTY. */
1366 up->parity_mask = 0xff;
1367 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1368 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1369 up->curregs[R3] = RxENAB | Rx8;
1370 up->curregs[R5] = TxENAB | Tx8;
1371 up->curregs[R6] = 0x00; /* SDLC Address */
1372 up->curregs[R7] = 0x7E; /* SDLC Flag */
1373 up->curregs[R9] = NV;
1374 up->curregs[R10] = NRZ;
1375 up->curregs[R11] = TCBR | RCBR;
1376 baud = 9600;
1377 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1378 up->curregs[R12] = (brg & 0xff);
1379 up->curregs[R13] = (brg >> 8) & 0xff;
1380 up->curregs[R14] = BRSRC | BRENAB;
1381 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
1382 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
1383 if (__load_zsregs(channel, up->curregs)) {
1384 up->flags |= SUNZILOG_FLAG_ESCC;
1385 }
1386 /* Only enable interrupts if an ISR handler available */
1387 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1388 up->curregs[R9] |= MIE;
1389 write_zsreg(channel, R9, up->curregs[R9]);
1390 }
1391
1392 spin_unlock_irqrestore(&up->port.lock, flags);
1393
1394#ifdef CONFIG_SERIO
1395 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1396 SUNZILOG_FLAG_CONS_MOUSE))
1397 sunzilog_register_serio(up);
1398#endif
1399}
1400
1401static int zilog_irq;
1402
1403static int zs_probe(struct platform_device *op)
1404{
1405 static int kbm_inst, uart_inst;
1406 int inst;
1407 struct uart_sunzilog_port *up;
1408 struct zilog_layout __iomem *rp;
1409 int keyboard_mouse = 0;
1410 int err;
1411
1412 if (of_find_property(op->dev.of_node, "keyboard", NULL))
1413 keyboard_mouse = 1;
1414
1415 /* uarts must come before keyboards/mice */
1416 if (keyboard_mouse)
1417 inst = uart_chip_count + kbm_inst;
1418 else
1419 inst = uart_inst;
1420
1421 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0,
1422 sizeof(struct zilog_layout),
1423 "zs");
1424 if (!sunzilog_chip_regs[inst])
1425 return -ENOMEM;
1426
1427 rp = sunzilog_chip_regs[inst];
1428
1429 if (!zilog_irq)
1430 zilog_irq = op->archdata.irqs[0];
1431
1432 up = &sunzilog_port_table[inst * 2];
1433
1434 /* Channel A */
1435 up[0].port.mapbase = op->resource[0].start + 0x00;
1436 up[0].port.membase = (void __iomem *) &rp->channelA;
1437 up[0].port.iotype = UPIO_MEM;
1438 up[0].port.irq = op->archdata.irqs[0];
1439 up[0].port.uartclk = ZS_CLOCK;
1440 up[0].port.fifosize = 1;
1441 up[0].port.ops = &sunzilog_pops;
1442 up[0].port.type = PORT_SUNZILOG;
1443 up[0].port.flags = 0;
1444 up[0].port.line = (inst * 2) + 0;
1445 up[0].port.dev = &op->dev;
1446 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A;
1447 if (keyboard_mouse)
1448 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB;
1449 sunzilog_init_hw(&up[0]);
1450
1451 /* Channel B */
1452 up[1].port.mapbase = op->resource[0].start + 0x04;
1453 up[1].port.membase = (void __iomem *) &rp->channelB;
1454 up[1].port.iotype = UPIO_MEM;
1455 up[1].port.irq = op->archdata.irqs[0];
1456 up[1].port.uartclk = ZS_CLOCK;
1457 up[1].port.fifosize = 1;
1458 up[1].port.ops = &sunzilog_pops;
1459 up[1].port.type = PORT_SUNZILOG;
1460 up[1].port.flags = 0;
1461 up[1].port.line = (inst * 2) + 1;
1462 up[1].port.dev = &op->dev;
1463 up[1].flags |= 0;
1464 if (keyboard_mouse)
1465 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE;
1466 sunzilog_init_hw(&up[1]);
1467
1468 if (!keyboard_mouse) {
1469 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1470 &sunzilog_reg, up[0].port.line,
1471 false))
1472 up->flags |= SUNZILOG_FLAG_IS_CONS;
1473 err = uart_add_one_port(&sunzilog_reg, &up[0].port);
1474 if (err) {
1475 of_iounmap(&op->resource[0],
1476 rp, sizeof(struct zilog_layout));
1477 return err;
1478 }
1479 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1480 &sunzilog_reg, up[1].port.line,
1481 false))
1482 up->flags |= SUNZILOG_FLAG_IS_CONS;
1483 err = uart_add_one_port(&sunzilog_reg, &up[1].port);
1484 if (err) {
1485 uart_remove_one_port(&sunzilog_reg, &up[0].port);
1486 of_iounmap(&op->resource[0],
1487 rp, sizeof(struct zilog_layout));
1488 return err;
1489 }
1490 uart_inst++;
1491 } else {
1492 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) "
1493 "is a %s\n",
1494 dev_name(&op->dev),
1495 (unsigned long long) up[0].port.mapbase,
1496 op->archdata.irqs[0], sunzilog_type(&up[0].port));
1497 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) "
1498 "is a %s\n",
1499 dev_name(&op->dev),
1500 (unsigned long long) up[1].port.mapbase,
1501 op->archdata.irqs[0], sunzilog_type(&up[1].port));
1502 kbm_inst++;
1503 }
1504
1505 platform_set_drvdata(op, &up[0]);
1506
1507 return 0;
1508}
1509
1510static void zs_remove_one(struct uart_sunzilog_port *up)
1511{
1512 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) {
1513#ifdef CONFIG_SERIO
1514 serio_unregister_port(&up->serio);
1515#endif
1516 } else
1517 uart_remove_one_port(&sunzilog_reg, &up->port);
1518}
1519
1520static int zs_remove(struct platform_device *op)
1521{
1522 struct uart_sunzilog_port *up = platform_get_drvdata(op);
1523 struct zilog_layout __iomem *regs;
1524
1525 zs_remove_one(&up[0]);
1526 zs_remove_one(&up[1]);
1527
1528 regs = sunzilog_chip_regs[up[0].port.line / 2];
1529 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout));
1530
1531 return 0;
1532}
1533
1534static const struct of_device_id zs_match[] = {
1535 {
1536 .name = "zs",
1537 },
1538 {},
1539};
1540MODULE_DEVICE_TABLE(of, zs_match);
1541
1542static struct platform_driver zs_driver = {
1543 .driver = {
1544 .name = "zs",
1545 .of_match_table = zs_match,
1546 },
1547 .probe = zs_probe,
1548 .remove = zs_remove,
1549};
1550
1551static int __init sunzilog_init(void)
1552{
1553 struct device_node *dp;
1554 int err;
1555 int num_keybms = 0;
1556 int num_sunzilog = 0;
1557
1558 for_each_node_by_name(dp, "zs") {
1559 num_sunzilog++;
1560 if (of_find_property(dp, "keyboard", NULL))
1561 num_keybms++;
1562 }
1563
1564 if (num_sunzilog) {
1565 err = sunzilog_alloc_tables(num_sunzilog);
1566 if (err)
1567 goto out;
1568
1569 uart_chip_count = num_sunzilog - num_keybms;
1570
1571 err = sunserial_register_minors(&sunzilog_reg,
1572 uart_chip_count * 2);
1573 if (err)
1574 goto out_free_tables;
1575 }
1576
1577 err = platform_driver_register(&zs_driver);
1578 if (err)
1579 goto out_unregister_uart;
1580
1581 if (zilog_irq) {
1582 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1583 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
1584 "zs", sunzilog_irq_chain);
1585 if (err)
1586 goto out_unregister_driver;
1587
1588 /* Enable Interrupts */
1589 while (up) {
1590 struct zilog_channel __iomem *channel;
1591
1592 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
1593 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1594 up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
1595 up->curregs[R9] |= MIE;
1596 write_zsreg(channel, R9, up->curregs[R9]);
1597 up = up->next;
1598 }
1599 }
1600
1601out:
1602 return err;
1603
1604out_unregister_driver:
1605 platform_driver_unregister(&zs_driver);
1606
1607out_unregister_uart:
1608 if (num_sunzilog) {
1609 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog);
1610 sunzilog_reg.cons = NULL;
1611 }
1612
1613out_free_tables:
1614 sunzilog_free_tables();
1615 goto out;
1616}
1617
1618static void __exit sunzilog_exit(void)
1619{
1620 platform_driver_unregister(&zs_driver);
1621
1622 if (zilog_irq) {
1623 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1624
1625 /* Disable Interrupts */
1626 while (up) {
1627 struct zilog_channel __iomem *channel;
1628
1629 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
1630 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1631 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
1632 up->curregs[R9] &= ~MIE;
1633 write_zsreg(channel, R9, up->curregs[R9]);
1634 up = up->next;
1635 }
1636
1637 free_irq(zilog_irq, sunzilog_irq_chain);
1638 zilog_irq = 0;
1639 }
1640
1641 if (sunzilog_reg.nr) {
1642 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr);
1643 sunzilog_free_tables();
1644 }
1645}
1646
1647module_init(sunzilog_init);
1648module_exit(sunzilog_exit);
1649
1650MODULE_AUTHOR("David S. Miller");
1651MODULE_DESCRIPTION("Sun Zilog serial port driver");
1652MODULE_VERSION("2.0");
1653MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0
2/* sunzilog.c: Zilog serial driver for Sparc systems.
3 *
4 * Driver for Zilog serial chips found on Sun workstations and
5 * servers. This driver could actually be made more generic.
6 *
7 * This is based on the old drivers/sbus/char/zs.c code. A lot
8 * of code has been simply moved over directly from there but
9 * much has been rewritten. Credits therefore go out to Eddie
10 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their
11 * work there.
12 *
13 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net)
14 */
15
16#include <linux/module.h>
17#include <linux/kernel.h>
18#include <linux/errno.h>
19#include <linux/delay.h>
20#include <linux/tty.h>
21#include <linux/tty_flip.h>
22#include <linux/major.h>
23#include <linux/string.h>
24#include <linux/ptrace.h>
25#include <linux/ioport.h>
26#include <linux/slab.h>
27#include <linux/circ_buf.h>
28#include <linux/serial.h>
29#include <linux/sysrq.h>
30#include <linux/console.h>
31#include <linux/spinlock.h>
32#ifdef CONFIG_SERIO
33#include <linux/serio.h>
34#endif
35#include <linux/init.h>
36#include <linux/of_device.h>
37
38#include <asm/io.h>
39#include <asm/irq.h>
40#include <asm/prom.h>
41#include <asm/setup.h>
42
43#include <linux/serial_core.h>
44#include <linux/sunserialcore.h>
45
46#include "sunzilog.h"
47
48/* On 32-bit sparcs we need to delay after register accesses
49 * to accommodate sun4 systems, but we do not need to flush writes.
50 * On 64-bit sparc we only need to flush single writes to ensure
51 * completion.
52 */
53#ifndef CONFIG_SPARC64
54#define ZSDELAY() udelay(5)
55#define ZSDELAY_LONG() udelay(20)
56#define ZS_WSYNC(channel) do { } while (0)
57#else
58#define ZSDELAY()
59#define ZSDELAY_LONG()
60#define ZS_WSYNC(__channel) \
61 readb(&((__channel)->control))
62#endif
63
64#define ZS_CLOCK 4915200 /* Zilog input clock rate. */
65#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
66
67/*
68 * We wrap our port structure around the generic uart_port.
69 */
70struct uart_sunzilog_port {
71 struct uart_port port;
72
73 /* IRQ servicing chain. */
74 struct uart_sunzilog_port *next;
75
76 /* Current values of Zilog write registers. */
77 unsigned char curregs[NUM_ZSREGS];
78
79 unsigned int flags;
80#define SUNZILOG_FLAG_CONS_KEYB 0x00000001
81#define SUNZILOG_FLAG_CONS_MOUSE 0x00000002
82#define SUNZILOG_FLAG_IS_CONS 0x00000004
83#define SUNZILOG_FLAG_IS_KGDB 0x00000008
84#define SUNZILOG_FLAG_MODEM_STATUS 0x00000010
85#define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020
86#define SUNZILOG_FLAG_REGS_HELD 0x00000040
87#define SUNZILOG_FLAG_TX_STOPPED 0x00000080
88#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100
89#define SUNZILOG_FLAG_ESCC 0x00000200
90#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400
91
92 unsigned int cflag;
93
94 unsigned char parity_mask;
95 unsigned char prev_status;
96
97#ifdef CONFIG_SERIO
98 struct serio serio;
99 int serio_open;
100#endif
101};
102
103static void sunzilog_putchar(struct uart_port *port, int ch);
104
105#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
106#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT))
107
108#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB)
109#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE)
110#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS)
111#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB)
112#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
113#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A)
114#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD)
115#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED)
116#define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE)
117
118/* Reading and writing Zilog8530 registers. The delays are to make this
119 * driver work on the Sun4 which needs a settling delay after each chip
120 * register access, other machines handle this in hardware via auxiliary
121 * flip-flops which implement the settle time we do in software.
122 *
123 * The port lock must be held and local IRQs must be disabled
124 * when {read,write}_zsreg is invoked.
125 */
126static unsigned char read_zsreg(struct zilog_channel __iomem *channel,
127 unsigned char reg)
128{
129 unsigned char retval;
130
131 writeb(reg, &channel->control);
132 ZSDELAY();
133 retval = readb(&channel->control);
134 ZSDELAY();
135
136 return retval;
137}
138
139static void write_zsreg(struct zilog_channel __iomem *channel,
140 unsigned char reg, unsigned char value)
141{
142 writeb(reg, &channel->control);
143 ZSDELAY();
144 writeb(value, &channel->control);
145 ZSDELAY();
146}
147
148static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
149{
150 int i;
151
152 for (i = 0; i < 32; i++) {
153 unsigned char regval;
154
155 regval = readb(&channel->control);
156 ZSDELAY();
157 if (regval & Rx_CH_AV)
158 break;
159
160 regval = read_zsreg(channel, R1);
161 readb(&channel->data);
162 ZSDELAY();
163
164 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
165 writeb(ERR_RES, &channel->control);
166 ZSDELAY();
167 ZS_WSYNC(channel);
168 }
169 }
170}
171
172/* This function must only be called when the TX is not busy. The UART
173 * port lock must be held and local interrupts disabled.
174 */
175static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
176{
177 int i;
178 int escc;
179 unsigned char r15;
180
181 /* Let pending transmits finish. */
182 for (i = 0; i < 1000; i++) {
183 unsigned char stat = read_zsreg(channel, R1);
184 if (stat & ALL_SNT)
185 break;
186 udelay(100);
187 }
188
189 writeb(ERR_RES, &channel->control);
190 ZSDELAY();
191 ZS_WSYNC(channel);
192
193 sunzilog_clear_fifo(channel);
194
195 /* Disable all interrupts. */
196 write_zsreg(channel, R1,
197 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
198
199 /* Set parity, sync config, stop bits, and clock divisor. */
200 write_zsreg(channel, R4, regs[R4]);
201
202 /* Set misc. TX/RX control bits. */
203 write_zsreg(channel, R10, regs[R10]);
204
205 /* Set TX/RX controls sans the enable bits. */
206 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
207 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
208
209 /* Synchronous mode config. */
210 write_zsreg(channel, R6, regs[R6]);
211 write_zsreg(channel, R7, regs[R7]);
212
213 /* Don't mess with the interrupt vector (R2, unused by us) and
214 * master interrupt control (R9). We make sure this is setup
215 * properly at probe time then never touch it again.
216 */
217
218 /* Disable baud generator. */
219 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
220
221 /* Clock mode control. */
222 write_zsreg(channel, R11, regs[R11]);
223
224 /* Lower and upper byte of baud rate generator divisor. */
225 write_zsreg(channel, R12, regs[R12]);
226 write_zsreg(channel, R13, regs[R13]);
227
228 /* Now rewrite R14, with BRENAB (if set). */
229 write_zsreg(channel, R14, regs[R14]);
230
231 /* External status interrupt control. */
232 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN);
233
234 /* ESCC Extension Register */
235 r15 = read_zsreg(channel, R15);
236 if (r15 & 0x01) {
237 write_zsreg(channel, R7, regs[R7p]);
238
239 /* External status interrupt and FIFO control. */
240 write_zsreg(channel, R15, regs[R15] & ~WR7pEN);
241 escc = 1;
242 } else {
243 /* Clear FIFO bit case it is an issue */
244 regs[R15] &= ~FIFOEN;
245 escc = 0;
246 }
247
248 /* Reset external status interrupts. */
249 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */
250 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */
251
252 /* Rewrite R3/R5, this time without enables masked. */
253 write_zsreg(channel, R3, regs[R3]);
254 write_zsreg(channel, R5, regs[R5]);
255
256 /* Rewrite R1, this time without IRQ enabled masked. */
257 write_zsreg(channel, R1, regs[R1]);
258
259 return escc;
260}
261
262/* Reprogram the Zilog channel HW registers with the copies found in the
263 * software state struct. If the transmitter is busy, we defer this update
264 * until the next TX complete interrupt. Else, we do it right now.
265 *
266 * The UART port lock must be held and local interrupts disabled.
267 */
268static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up,
269 struct zilog_channel __iomem *channel)
270{
271 if (!ZS_REGS_HELD(up)) {
272 if (ZS_TX_ACTIVE(up)) {
273 up->flags |= SUNZILOG_FLAG_REGS_HELD;
274 } else {
275 __load_zsregs(channel, up->curregs);
276 }
277 }
278}
279
280static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up)
281{
282 unsigned int cur_cflag = up->cflag;
283 int brg, new_baud;
284
285 up->cflag &= ~CBAUD;
286 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
287
288 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
289 up->curregs[R12] = (brg & 0xff);
290 up->curregs[R13] = (brg >> 8) & 0xff;
291 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port));
292}
293
294static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
295 unsigned char ch, int is_break)
296{
297 if (ZS_IS_KEYB(up)) {
298 /* Stop-A is handled by drivers/char/keyboard.c now. */
299#ifdef CONFIG_SERIO
300 if (up->serio_open)
301 serio_interrupt(&up->serio, ch, 0);
302#endif
303 } else if (ZS_IS_MOUSE(up)) {
304 int ret = suncore_mouse_baud_detection(ch, is_break);
305
306 switch (ret) {
307 case 2:
308 sunzilog_change_mouse_baud(up);
309 fallthrough;
310 case 1:
311 break;
312
313 case 0:
314#ifdef CONFIG_SERIO
315 if (up->serio_open)
316 serio_interrupt(&up->serio, ch, 0);
317#endif
318 break;
319 }
320 }
321}
322
323static struct tty_port *
324sunzilog_receive_chars(struct uart_sunzilog_port *up,
325 struct zilog_channel __iomem *channel)
326{
327 struct tty_port *port = NULL;
328 unsigned char ch, r1, flag;
329
330 if (up->port.state != NULL) /* Unopened serial console */
331 port = &up->port.state->port;
332
333 for (;;) {
334
335 r1 = read_zsreg(channel, R1);
336 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
337 writeb(ERR_RES, &channel->control);
338 ZSDELAY();
339 ZS_WSYNC(channel);
340 }
341
342 ch = readb(&channel->control);
343 ZSDELAY();
344
345 /* This funny hack depends upon BRK_ABRT not interfering
346 * with the other bits we care about in R1.
347 */
348 if (ch & BRK_ABRT)
349 r1 |= BRK_ABRT;
350
351 if (!(ch & Rx_CH_AV))
352 break;
353
354 ch = readb(&channel->data);
355 ZSDELAY();
356
357 ch &= up->parity_mask;
358
359 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) {
360 sunzilog_kbdms_receive_chars(up, ch, 0);
361 continue;
362 }
363
364 /* A real serial line, record the character and status. */
365 flag = TTY_NORMAL;
366 up->port.icount.rx++;
367 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
368 if (r1 & BRK_ABRT) {
369 r1 &= ~(PAR_ERR | CRC_ERR);
370 up->port.icount.brk++;
371 if (uart_handle_break(&up->port))
372 continue;
373 }
374 else if (r1 & PAR_ERR)
375 up->port.icount.parity++;
376 else if (r1 & CRC_ERR)
377 up->port.icount.frame++;
378 if (r1 & Rx_OVR)
379 up->port.icount.overrun++;
380 r1 &= up->port.read_status_mask;
381 if (r1 & BRK_ABRT)
382 flag = TTY_BREAK;
383 else if (r1 & PAR_ERR)
384 flag = TTY_PARITY;
385 else if (r1 & CRC_ERR)
386 flag = TTY_FRAME;
387 }
388 if (uart_handle_sysrq_char(&up->port, ch) || !port)
389 continue;
390
391 if (up->port.ignore_status_mask == 0xff ||
392 (r1 & up->port.ignore_status_mask) == 0) {
393 tty_insert_flip_char(port, ch, flag);
394 }
395 if (r1 & Rx_OVR)
396 tty_insert_flip_char(port, 0, TTY_OVERRUN);
397 }
398
399 return port;
400}
401
402static void sunzilog_status_handle(struct uart_sunzilog_port *up,
403 struct zilog_channel __iomem *channel)
404{
405 unsigned char status;
406
407 status = readb(&channel->control);
408 ZSDELAY();
409
410 writeb(RES_EXT_INT, &channel->control);
411 ZSDELAY();
412 ZS_WSYNC(channel);
413
414 if (status & BRK_ABRT) {
415 if (ZS_IS_MOUSE(up))
416 sunzilog_kbdms_receive_chars(up, 0, 1);
417 if (ZS_IS_CONS(up)) {
418 /* Wait for BREAK to deassert to avoid potentially
419 * confusing the PROM.
420 */
421 while (1) {
422 status = readb(&channel->control);
423 ZSDELAY();
424 if (!(status & BRK_ABRT))
425 break;
426 }
427 sun_do_break();
428 return;
429 }
430 }
431
432 if (ZS_WANTS_MODEM_STATUS(up)) {
433 if (status & SYNC)
434 up->port.icount.dsr++;
435
436 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
437 * But it does not tell us which bit has changed, we have to keep
438 * track of this ourselves.
439 */
440 if ((status ^ up->prev_status) ^ DCD)
441 uart_handle_dcd_change(&up->port,
442 (status & DCD));
443 if ((status ^ up->prev_status) ^ CTS)
444 uart_handle_cts_change(&up->port,
445 (status & CTS));
446
447 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
448 }
449
450 up->prev_status = status;
451}
452
453static void sunzilog_transmit_chars(struct uart_sunzilog_port *up,
454 struct zilog_channel __iomem *channel)
455{
456 struct circ_buf *xmit;
457
458 if (ZS_IS_CONS(up)) {
459 unsigned char status = readb(&channel->control);
460 ZSDELAY();
461
462 /* TX still busy? Just wait for the next TX done interrupt.
463 *
464 * It can occur because of how we do serial console writes. It would
465 * be nice to transmit console writes just like we normally would for
466 * a TTY line. (ie. buffered and TX interrupt driven). That is not
467 * easy because console writes cannot sleep. One solution might be
468 * to poll on enough port->xmit space becoming free. -DaveM
469 */
470 if (!(status & Tx_BUF_EMP))
471 return;
472 }
473
474 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE;
475
476 if (ZS_REGS_HELD(up)) {
477 __load_zsregs(channel, up->curregs);
478 up->flags &= ~SUNZILOG_FLAG_REGS_HELD;
479 }
480
481 if (ZS_TX_STOPPED(up)) {
482 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
483 goto ack_tx_int;
484 }
485
486 if (up->port.x_char) {
487 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
488 writeb(up->port.x_char, &channel->data);
489 ZSDELAY();
490 ZS_WSYNC(channel);
491
492 up->port.icount.tx++;
493 up->port.x_char = 0;
494 return;
495 }
496
497 if (up->port.state == NULL)
498 goto ack_tx_int;
499 xmit = &up->port.state->xmit;
500 if (uart_circ_empty(xmit))
501 goto ack_tx_int;
502
503 if (uart_tx_stopped(&up->port))
504 goto ack_tx_int;
505
506 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
507 writeb(xmit->buf[xmit->tail], &channel->data);
508 ZSDELAY();
509 ZS_WSYNC(channel);
510
511 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
512 up->port.icount.tx++;
513
514 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
515 uart_write_wakeup(&up->port);
516
517 return;
518
519ack_tx_int:
520 writeb(RES_Tx_P, &channel->control);
521 ZSDELAY();
522 ZS_WSYNC(channel);
523}
524
525static irqreturn_t sunzilog_interrupt(int irq, void *dev_id)
526{
527 struct uart_sunzilog_port *up = dev_id;
528
529 while (up) {
530 struct zilog_channel __iomem *channel
531 = ZILOG_CHANNEL_FROM_PORT(&up->port);
532 struct tty_port *port;
533 unsigned char r3;
534
535 spin_lock(&up->port.lock);
536 r3 = read_zsreg(channel, R3);
537
538 /* Channel A */
539 port = NULL;
540 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
541 writeb(RES_H_IUS, &channel->control);
542 ZSDELAY();
543 ZS_WSYNC(channel);
544
545 if (r3 & CHARxIP)
546 port = sunzilog_receive_chars(up, channel);
547 if (r3 & CHAEXT)
548 sunzilog_status_handle(up, channel);
549 if (r3 & CHATxIP)
550 sunzilog_transmit_chars(up, channel);
551 }
552 spin_unlock(&up->port.lock);
553
554 if (port)
555 tty_flip_buffer_push(port);
556
557 /* Channel B */
558 up = up->next;
559 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
560
561 spin_lock(&up->port.lock);
562 port = NULL;
563 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
564 writeb(RES_H_IUS, &channel->control);
565 ZSDELAY();
566 ZS_WSYNC(channel);
567
568 if (r3 & CHBRxIP)
569 port = sunzilog_receive_chars(up, channel);
570 if (r3 & CHBEXT)
571 sunzilog_status_handle(up, channel);
572 if (r3 & CHBTxIP)
573 sunzilog_transmit_chars(up, channel);
574 }
575 spin_unlock(&up->port.lock);
576
577 if (port)
578 tty_flip_buffer_push(port);
579
580 up = up->next;
581 }
582
583 return IRQ_HANDLED;
584}
585
586/* A convenient way to quickly get R0 status. The caller must _not_ hold the
587 * port lock, it is acquired here.
588 */
589static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
590{
591 struct zilog_channel __iomem *channel;
592 unsigned char status;
593
594 channel = ZILOG_CHANNEL_FROM_PORT(port);
595 status = readb(&channel->control);
596 ZSDELAY();
597
598 return status;
599}
600
601/* The port lock is not held. */
602static unsigned int sunzilog_tx_empty(struct uart_port *port)
603{
604 unsigned long flags;
605 unsigned char status;
606 unsigned int ret;
607
608 spin_lock_irqsave(&port->lock, flags);
609
610 status = sunzilog_read_channel_status(port);
611
612 spin_unlock_irqrestore(&port->lock, flags);
613
614 if (status & Tx_BUF_EMP)
615 ret = TIOCSER_TEMT;
616 else
617 ret = 0;
618
619 return ret;
620}
621
622/* The port lock is held and interrupts are disabled. */
623static unsigned int sunzilog_get_mctrl(struct uart_port *port)
624{
625 unsigned char status;
626 unsigned int ret;
627
628 status = sunzilog_read_channel_status(port);
629
630 ret = 0;
631 if (status & DCD)
632 ret |= TIOCM_CAR;
633 if (status & SYNC)
634 ret |= TIOCM_DSR;
635 if (status & CTS)
636 ret |= TIOCM_CTS;
637
638 return ret;
639}
640
641/* The port lock is held and interrupts are disabled. */
642static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
643{
644 struct uart_sunzilog_port *up =
645 container_of(port, struct uart_sunzilog_port, port);
646 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
647 unsigned char set_bits, clear_bits;
648
649 set_bits = clear_bits = 0;
650
651 if (mctrl & TIOCM_RTS)
652 set_bits |= RTS;
653 else
654 clear_bits |= RTS;
655 if (mctrl & TIOCM_DTR)
656 set_bits |= DTR;
657 else
658 clear_bits |= DTR;
659
660 /* NOTE: Not subject to 'transmitter active' rule. */
661 up->curregs[R5] |= set_bits;
662 up->curregs[R5] &= ~clear_bits;
663 write_zsreg(channel, R5, up->curregs[R5]);
664}
665
666/* The port lock is held and interrupts are disabled. */
667static void sunzilog_stop_tx(struct uart_port *port)
668{
669 struct uart_sunzilog_port *up =
670 container_of(port, struct uart_sunzilog_port, port);
671
672 up->flags |= SUNZILOG_FLAG_TX_STOPPED;
673}
674
675/* The port lock is held and interrupts are disabled. */
676static void sunzilog_start_tx(struct uart_port *port)
677{
678 struct uart_sunzilog_port *up =
679 container_of(port, struct uart_sunzilog_port, port);
680 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
681 unsigned char status;
682
683 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
684 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
685
686 status = readb(&channel->control);
687 ZSDELAY();
688
689 /* TX busy? Just wait for the TX done interrupt. */
690 if (!(status & Tx_BUF_EMP))
691 return;
692
693 /* Send the first character to jump-start the TX done
694 * IRQ sending engine.
695 */
696 if (port->x_char) {
697 writeb(port->x_char, &channel->data);
698 ZSDELAY();
699 ZS_WSYNC(channel);
700
701 port->icount.tx++;
702 port->x_char = 0;
703 } else {
704 struct circ_buf *xmit = &port->state->xmit;
705
706 if (uart_circ_empty(xmit))
707 return;
708 writeb(xmit->buf[xmit->tail], &channel->data);
709 ZSDELAY();
710 ZS_WSYNC(channel);
711
712 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
713 port->icount.tx++;
714
715 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
716 uart_write_wakeup(&up->port);
717 }
718}
719
720/* The port lock is held. */
721static void sunzilog_stop_rx(struct uart_port *port)
722{
723 struct uart_sunzilog_port *up = UART_ZILOG(port);
724 struct zilog_channel __iomem *channel;
725
726 if (ZS_IS_CONS(up))
727 return;
728
729 channel = ZILOG_CHANNEL_FROM_PORT(port);
730
731 /* Disable all RX interrupts. */
732 up->curregs[R1] &= ~RxINT_MASK;
733 sunzilog_maybe_update_regs(up, channel);
734}
735
736/* The port lock is held. */
737static void sunzilog_enable_ms(struct uart_port *port)
738{
739 struct uart_sunzilog_port *up =
740 container_of(port, struct uart_sunzilog_port, port);
741 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
742 unsigned char new_reg;
743
744 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
745 if (new_reg != up->curregs[R15]) {
746 up->curregs[R15] = new_reg;
747
748 /* NOTE: Not subject to 'transmitter active' rule. */
749 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
750 }
751}
752
753/* The port lock is not held. */
754static void sunzilog_break_ctl(struct uart_port *port, int break_state)
755{
756 struct uart_sunzilog_port *up =
757 container_of(port, struct uart_sunzilog_port, port);
758 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
759 unsigned char set_bits, clear_bits, new_reg;
760 unsigned long flags;
761
762 set_bits = clear_bits = 0;
763
764 if (break_state)
765 set_bits |= SND_BRK;
766 else
767 clear_bits |= SND_BRK;
768
769 spin_lock_irqsave(&port->lock, flags);
770
771 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
772 if (new_reg != up->curregs[R5]) {
773 up->curregs[R5] = new_reg;
774
775 /* NOTE: Not subject to 'transmitter active' rule. */
776 write_zsreg(channel, R5, up->curregs[R5]);
777 }
778
779 spin_unlock_irqrestore(&port->lock, flags);
780}
781
782static void __sunzilog_startup(struct uart_sunzilog_port *up)
783{
784 struct zilog_channel __iomem *channel;
785
786 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
787 up->prev_status = readb(&channel->control);
788
789 /* Enable receiver and transmitter. */
790 up->curregs[R3] |= RxENAB;
791 up->curregs[R5] |= TxENAB;
792
793 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
794 sunzilog_maybe_update_regs(up, channel);
795}
796
797static int sunzilog_startup(struct uart_port *port)
798{
799 struct uart_sunzilog_port *up = UART_ZILOG(port);
800 unsigned long flags;
801
802 if (ZS_IS_CONS(up))
803 return 0;
804
805 spin_lock_irqsave(&port->lock, flags);
806 __sunzilog_startup(up);
807 spin_unlock_irqrestore(&port->lock, flags);
808 return 0;
809}
810
811/*
812 * The test for ZS_IS_CONS is explained by the following e-mail:
813 *****
814 * From: Russell King <rmk@arm.linux.org.uk>
815 * Date: Sun, 8 Dec 2002 10:18:38 +0000
816 *
817 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
818 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
819 * > and I noticed that something is not right with reference
820 * > counting in this case. It seems that when the console
821 * > is open by kernel initially, this is not accounted
822 * > as an open, and uart_startup is not called.
823 *
824 * That is correct. We are unable to call uart_startup when the serial
825 * console is initialised because it may need to allocate memory (as
826 * request_irq does) and the memory allocators may not have been
827 * initialised.
828 *
829 * 1. initialise the port into a state where it can send characters in the
830 * console write method.
831 *
832 * 2. don't do the actual hardware shutdown in your shutdown() method (but
833 * do the normal software shutdown - ie, free irqs etc)
834 *****
835 */
836static void sunzilog_shutdown(struct uart_port *port)
837{
838 struct uart_sunzilog_port *up = UART_ZILOG(port);
839 struct zilog_channel __iomem *channel;
840 unsigned long flags;
841
842 if (ZS_IS_CONS(up))
843 return;
844
845 spin_lock_irqsave(&port->lock, flags);
846
847 channel = ZILOG_CHANNEL_FROM_PORT(port);
848
849 /* Disable receiver and transmitter. */
850 up->curregs[R3] &= ~RxENAB;
851 up->curregs[R5] &= ~TxENAB;
852
853 /* Disable all interrupts and BRK assertion. */
854 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
855 up->curregs[R5] &= ~SND_BRK;
856 sunzilog_maybe_update_regs(up, channel);
857
858 spin_unlock_irqrestore(&port->lock, flags);
859}
860
861/* Shared by TTY driver and serial console setup. The port lock is held
862 * and local interrupts are disabled.
863 */
864static void
865sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag,
866 unsigned int iflag, int brg)
867{
868
869 up->curregs[R10] = NRZ;
870 up->curregs[R11] = TCBR | RCBR;
871
872 /* Program BAUD and clock source. */
873 up->curregs[R4] &= ~XCLK_MASK;
874 up->curregs[R4] |= X16CLK;
875 up->curregs[R12] = brg & 0xff;
876 up->curregs[R13] = (brg >> 8) & 0xff;
877 up->curregs[R14] = BRSRC | BRENAB;
878
879 /* Character size, stop bits, and parity. */
880 up->curregs[R3] &= ~RxN_MASK;
881 up->curregs[R5] &= ~TxN_MASK;
882 switch (cflag & CSIZE) {
883 case CS5:
884 up->curregs[R3] |= Rx5;
885 up->curregs[R5] |= Tx5;
886 up->parity_mask = 0x1f;
887 break;
888 case CS6:
889 up->curregs[R3] |= Rx6;
890 up->curregs[R5] |= Tx6;
891 up->parity_mask = 0x3f;
892 break;
893 case CS7:
894 up->curregs[R3] |= Rx7;
895 up->curregs[R5] |= Tx7;
896 up->parity_mask = 0x7f;
897 break;
898 case CS8:
899 default:
900 up->curregs[R3] |= Rx8;
901 up->curregs[R5] |= Tx8;
902 up->parity_mask = 0xff;
903 break;
904 }
905 up->curregs[R4] &= ~0x0c;
906 if (cflag & CSTOPB)
907 up->curregs[R4] |= SB2;
908 else
909 up->curregs[R4] |= SB1;
910 if (cflag & PARENB)
911 up->curregs[R4] |= PAR_ENAB;
912 else
913 up->curregs[R4] &= ~PAR_ENAB;
914 if (!(cflag & PARODD))
915 up->curregs[R4] |= PAR_EVEN;
916 else
917 up->curregs[R4] &= ~PAR_EVEN;
918
919 up->port.read_status_mask = Rx_OVR;
920 if (iflag & INPCK)
921 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
922 if (iflag & (IGNBRK | BRKINT | PARMRK))
923 up->port.read_status_mask |= BRK_ABRT;
924
925 up->port.ignore_status_mask = 0;
926 if (iflag & IGNPAR)
927 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
928 if (iflag & IGNBRK) {
929 up->port.ignore_status_mask |= BRK_ABRT;
930 if (iflag & IGNPAR)
931 up->port.ignore_status_mask |= Rx_OVR;
932 }
933
934 if ((cflag & CREAD) == 0)
935 up->port.ignore_status_mask = 0xff;
936}
937
938/* The port lock is not held. */
939static void
940sunzilog_set_termios(struct uart_port *port, struct ktermios *termios,
941 struct ktermios *old)
942{
943 struct uart_sunzilog_port *up =
944 container_of(port, struct uart_sunzilog_port, port);
945 unsigned long flags;
946 int baud, brg;
947
948 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
949
950 spin_lock_irqsave(&up->port.lock, flags);
951
952 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
953
954 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
955
956 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
957 up->flags |= SUNZILOG_FLAG_MODEM_STATUS;
958 else
959 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS;
960
961 up->cflag = termios->c_cflag;
962
963 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
964
965 uart_update_timeout(port, termios->c_cflag, baud);
966
967 spin_unlock_irqrestore(&up->port.lock, flags);
968}
969
970static const char *sunzilog_type(struct uart_port *port)
971{
972 struct uart_sunzilog_port *up = UART_ZILOG(port);
973
974 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs";
975}
976
977/* We do not request/release mappings of the registers here, this
978 * happens at early serial probe time.
979 */
980static void sunzilog_release_port(struct uart_port *port)
981{
982}
983
984static int sunzilog_request_port(struct uart_port *port)
985{
986 return 0;
987}
988
989/* These do not need to do anything interesting either. */
990static void sunzilog_config_port(struct uart_port *port, int flags)
991{
992}
993
994/* We do not support letting the user mess with the divisor, IRQ, etc. */
995static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
996{
997 return -EINVAL;
998}
999
1000#ifdef CONFIG_CONSOLE_POLL
1001static int sunzilog_get_poll_char(struct uart_port *port)
1002{
1003 unsigned char ch, r1;
1004 struct uart_sunzilog_port *up =
1005 container_of(port, struct uart_sunzilog_port, port);
1006 struct zilog_channel __iomem *channel
1007 = ZILOG_CHANNEL_FROM_PORT(&up->port);
1008
1009
1010 r1 = read_zsreg(channel, R1);
1011 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
1012 writeb(ERR_RES, &channel->control);
1013 ZSDELAY();
1014 ZS_WSYNC(channel);
1015 }
1016
1017 ch = readb(&channel->control);
1018 ZSDELAY();
1019
1020 /* This funny hack depends upon BRK_ABRT not interfering
1021 * with the other bits we care about in R1.
1022 */
1023 if (ch & BRK_ABRT)
1024 r1 |= BRK_ABRT;
1025
1026 if (!(ch & Rx_CH_AV))
1027 return NO_POLL_CHAR;
1028
1029 ch = readb(&channel->data);
1030 ZSDELAY();
1031
1032 ch &= up->parity_mask;
1033 return ch;
1034}
1035
1036static void sunzilog_put_poll_char(struct uart_port *port,
1037 unsigned char ch)
1038{
1039 struct uart_sunzilog_port *up =
1040 container_of(port, struct uart_sunzilog_port, port);
1041
1042 sunzilog_putchar(&up->port, ch);
1043}
1044#endif /* CONFIG_CONSOLE_POLL */
1045
1046static const struct uart_ops sunzilog_pops = {
1047 .tx_empty = sunzilog_tx_empty,
1048 .set_mctrl = sunzilog_set_mctrl,
1049 .get_mctrl = sunzilog_get_mctrl,
1050 .stop_tx = sunzilog_stop_tx,
1051 .start_tx = sunzilog_start_tx,
1052 .stop_rx = sunzilog_stop_rx,
1053 .enable_ms = sunzilog_enable_ms,
1054 .break_ctl = sunzilog_break_ctl,
1055 .startup = sunzilog_startup,
1056 .shutdown = sunzilog_shutdown,
1057 .set_termios = sunzilog_set_termios,
1058 .type = sunzilog_type,
1059 .release_port = sunzilog_release_port,
1060 .request_port = sunzilog_request_port,
1061 .config_port = sunzilog_config_port,
1062 .verify_port = sunzilog_verify_port,
1063#ifdef CONFIG_CONSOLE_POLL
1064 .poll_get_char = sunzilog_get_poll_char,
1065 .poll_put_char = sunzilog_put_poll_char,
1066#endif
1067};
1068
1069static int uart_chip_count;
1070static struct uart_sunzilog_port *sunzilog_port_table;
1071static struct zilog_layout __iomem **sunzilog_chip_regs;
1072
1073static struct uart_sunzilog_port *sunzilog_irq_chain;
1074
1075static struct uart_driver sunzilog_reg = {
1076 .owner = THIS_MODULE,
1077 .driver_name = "sunzilog",
1078 .dev_name = "ttyS",
1079 .major = TTY_MAJOR,
1080};
1081
1082static int __init sunzilog_alloc_tables(int num_sunzilog)
1083{
1084 struct uart_sunzilog_port *up;
1085 unsigned long size;
1086 int num_channels = num_sunzilog * 2;
1087 int i;
1088
1089 size = num_channels * sizeof(struct uart_sunzilog_port);
1090 sunzilog_port_table = kzalloc(size, GFP_KERNEL);
1091 if (!sunzilog_port_table)
1092 return -ENOMEM;
1093
1094 for (i = 0; i < num_channels; i++) {
1095 up = &sunzilog_port_table[i];
1096
1097 spin_lock_init(&up->port.lock);
1098
1099 if (i == 0)
1100 sunzilog_irq_chain = up;
1101
1102 if (i < num_channels - 1)
1103 up->next = up + 1;
1104 else
1105 up->next = NULL;
1106 }
1107
1108 size = num_sunzilog * sizeof(struct zilog_layout __iomem *);
1109 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL);
1110 if (!sunzilog_chip_regs) {
1111 kfree(sunzilog_port_table);
1112 sunzilog_irq_chain = NULL;
1113 return -ENOMEM;
1114 }
1115
1116 return 0;
1117}
1118
1119static void sunzilog_free_tables(void)
1120{
1121 kfree(sunzilog_port_table);
1122 sunzilog_irq_chain = NULL;
1123 kfree(sunzilog_chip_regs);
1124}
1125
1126#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
1127
1128static void sunzilog_putchar(struct uart_port *port, int ch)
1129{
1130 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
1131 int loops = ZS_PUT_CHAR_MAX_DELAY;
1132
1133 /* This is a timed polling loop so do not switch the explicit
1134 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1135 */
1136 do {
1137 unsigned char val = readb(&channel->control);
1138 if (val & Tx_BUF_EMP) {
1139 ZSDELAY();
1140 break;
1141 }
1142 udelay(5);
1143 } while (--loops);
1144
1145 writeb(ch, &channel->data);
1146 ZSDELAY();
1147 ZS_WSYNC(channel);
1148}
1149
1150#ifdef CONFIG_SERIO
1151
1152static DEFINE_SPINLOCK(sunzilog_serio_lock);
1153
1154static int sunzilog_serio_write(struct serio *serio, unsigned char ch)
1155{
1156 struct uart_sunzilog_port *up = serio->port_data;
1157 unsigned long flags;
1158
1159 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1160
1161 sunzilog_putchar(&up->port, ch);
1162
1163 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1164
1165 return 0;
1166}
1167
1168static int sunzilog_serio_open(struct serio *serio)
1169{
1170 struct uart_sunzilog_port *up = serio->port_data;
1171 unsigned long flags;
1172 int ret;
1173
1174 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1175 if (!up->serio_open) {
1176 up->serio_open = 1;
1177 ret = 0;
1178 } else
1179 ret = -EBUSY;
1180 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1181
1182 return ret;
1183}
1184
1185static void sunzilog_serio_close(struct serio *serio)
1186{
1187 struct uart_sunzilog_port *up = serio->port_data;
1188 unsigned long flags;
1189
1190 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1191 up->serio_open = 0;
1192 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1193}
1194
1195#endif /* CONFIG_SERIO */
1196
1197#ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE
1198static void
1199sunzilog_console_write(struct console *con, const char *s, unsigned int count)
1200{
1201 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1202 unsigned long flags;
1203 int locked = 1;
1204
1205 if (up->port.sysrq || oops_in_progress)
1206 locked = spin_trylock_irqsave(&up->port.lock, flags);
1207 else
1208 spin_lock_irqsave(&up->port.lock, flags);
1209
1210 uart_console_write(&up->port, s, count, sunzilog_putchar);
1211 udelay(2);
1212
1213 if (locked)
1214 spin_unlock_irqrestore(&up->port.lock, flags);
1215}
1216
1217static int __init sunzilog_console_setup(struct console *con, char *options)
1218{
1219 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1220 unsigned long flags;
1221 int baud, brg;
1222
1223 if (up->port.type != PORT_SUNZILOG)
1224 return -EINVAL;
1225
1226 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n",
1227 (sunzilog_reg.minor - 64) + con->index, con->index);
1228
1229 /* Get firmware console settings. */
1230 sunserial_console_termios(con, up->port.dev->of_node);
1231
1232 /* Firmware console speed is limited to 150-->38400 baud so
1233 * this hackish cflag thing is OK.
1234 */
1235 switch (con->cflag & CBAUD) {
1236 case B150: baud = 150; break;
1237 case B300: baud = 300; break;
1238 case B600: baud = 600; break;
1239 case B1200: baud = 1200; break;
1240 case B2400: baud = 2400; break;
1241 case B4800: baud = 4800; break;
1242 default: case B9600: baud = 9600; break;
1243 case B19200: baud = 19200; break;
1244 case B38400: baud = 38400; break;
1245 }
1246
1247 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1248
1249 spin_lock_irqsave(&up->port.lock, flags);
1250
1251 up->curregs[R15] |= BRKIE;
1252 sunzilog_convert_to_zs(up, con->cflag, 0, brg);
1253
1254 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1255 __sunzilog_startup(up);
1256
1257 spin_unlock_irqrestore(&up->port.lock, flags);
1258
1259 return 0;
1260}
1261
1262static struct console sunzilog_console_ops = {
1263 .name = "ttyS",
1264 .write = sunzilog_console_write,
1265 .device = uart_console_device,
1266 .setup = sunzilog_console_setup,
1267 .flags = CON_PRINTBUFFER,
1268 .index = -1,
1269 .data = &sunzilog_reg,
1270};
1271
1272static inline struct console *SUNZILOG_CONSOLE(void)
1273{
1274 return &sunzilog_console_ops;
1275}
1276
1277#else
1278#define SUNZILOG_CONSOLE() (NULL)
1279#endif
1280
1281static void sunzilog_init_kbdms(struct uart_sunzilog_port *up)
1282{
1283 int baud, brg;
1284
1285 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1286 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1287 baud = 1200;
1288 } else {
1289 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1290 baud = 4800;
1291 }
1292
1293 up->curregs[R15] |= BRKIE;
1294 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1295 sunzilog_convert_to_zs(up, up->cflag, 0, brg);
1296 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1297 __sunzilog_startup(up);
1298}
1299
1300#ifdef CONFIG_SERIO
1301static void sunzilog_register_serio(struct uart_sunzilog_port *up)
1302{
1303 struct serio *serio = &up->serio;
1304
1305 serio->port_data = up;
1306
1307 serio->id.type = SERIO_RS232;
1308 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1309 serio->id.proto = SERIO_SUNKBD;
1310 strlcpy(serio->name, "zskbd", sizeof(serio->name));
1311 } else {
1312 serio->id.proto = SERIO_SUN;
1313 serio->id.extra = 1;
1314 strlcpy(serio->name, "zsms", sizeof(serio->name));
1315 }
1316 strlcpy(serio->phys,
1317 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ?
1318 "zs/serio0" : "zs/serio1"),
1319 sizeof(serio->phys));
1320
1321 serio->write = sunzilog_serio_write;
1322 serio->open = sunzilog_serio_open;
1323 serio->close = sunzilog_serio_close;
1324 serio->dev.parent = up->port.dev;
1325
1326 serio_register_port(serio);
1327}
1328#endif
1329
1330static void sunzilog_init_hw(struct uart_sunzilog_port *up)
1331{
1332 struct zilog_channel __iomem *channel;
1333 unsigned long flags;
1334 int baud, brg;
1335
1336 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1337
1338 spin_lock_irqsave(&up->port.lock, flags);
1339 if (ZS_IS_CHANNEL_A(up)) {
1340 write_zsreg(channel, R9, FHWRES);
1341 ZSDELAY_LONG();
1342 (void) read_zsreg(channel, R0);
1343 }
1344
1345 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1346 SUNZILOG_FLAG_CONS_MOUSE)) {
1347 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1348 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1349 up->curregs[R3] = RxENAB | Rx8;
1350 up->curregs[R5] = TxENAB | Tx8;
1351 up->curregs[R6] = 0x00; /* SDLC Address */
1352 up->curregs[R7] = 0x7E; /* SDLC Flag */
1353 up->curregs[R9] = NV;
1354 up->curregs[R7p] = 0x00;
1355 sunzilog_init_kbdms(up);
1356 /* Only enable interrupts if an ISR handler available */
1357 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1358 up->curregs[R9] |= MIE;
1359 write_zsreg(channel, R9, up->curregs[R9]);
1360 } else {
1361 /* Normal serial TTY. */
1362 up->parity_mask = 0xff;
1363 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1364 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1365 up->curregs[R3] = RxENAB | Rx8;
1366 up->curregs[R5] = TxENAB | Tx8;
1367 up->curregs[R6] = 0x00; /* SDLC Address */
1368 up->curregs[R7] = 0x7E; /* SDLC Flag */
1369 up->curregs[R9] = NV;
1370 up->curregs[R10] = NRZ;
1371 up->curregs[R11] = TCBR | RCBR;
1372 baud = 9600;
1373 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1374 up->curregs[R12] = (brg & 0xff);
1375 up->curregs[R13] = (brg >> 8) & 0xff;
1376 up->curregs[R14] = BRSRC | BRENAB;
1377 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
1378 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
1379 if (__load_zsregs(channel, up->curregs)) {
1380 up->flags |= SUNZILOG_FLAG_ESCC;
1381 }
1382 /* Only enable interrupts if an ISR handler available */
1383 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1384 up->curregs[R9] |= MIE;
1385 write_zsreg(channel, R9, up->curregs[R9]);
1386 }
1387
1388 spin_unlock_irqrestore(&up->port.lock, flags);
1389
1390#ifdef CONFIG_SERIO
1391 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1392 SUNZILOG_FLAG_CONS_MOUSE))
1393 sunzilog_register_serio(up);
1394#endif
1395}
1396
1397static int zilog_irq;
1398
1399static int zs_probe(struct platform_device *op)
1400{
1401 static int kbm_inst, uart_inst;
1402 int inst;
1403 struct uart_sunzilog_port *up;
1404 struct zilog_layout __iomem *rp;
1405 int keyboard_mouse = 0;
1406 int err;
1407
1408 if (of_find_property(op->dev.of_node, "keyboard", NULL))
1409 keyboard_mouse = 1;
1410
1411 /* uarts must come before keyboards/mice */
1412 if (keyboard_mouse)
1413 inst = uart_chip_count + kbm_inst;
1414 else
1415 inst = uart_inst;
1416
1417 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0,
1418 sizeof(struct zilog_layout),
1419 "zs");
1420 if (!sunzilog_chip_regs[inst])
1421 return -ENOMEM;
1422
1423 rp = sunzilog_chip_regs[inst];
1424
1425 if (!zilog_irq)
1426 zilog_irq = op->archdata.irqs[0];
1427
1428 up = &sunzilog_port_table[inst * 2];
1429
1430 /* Channel A */
1431 up[0].port.mapbase = op->resource[0].start + 0x00;
1432 up[0].port.membase = (void __iomem *) &rp->channelA;
1433 up[0].port.iotype = UPIO_MEM;
1434 up[0].port.irq = op->archdata.irqs[0];
1435 up[0].port.uartclk = ZS_CLOCK;
1436 up[0].port.fifosize = 1;
1437 up[0].port.ops = &sunzilog_pops;
1438 up[0].port.type = PORT_SUNZILOG;
1439 up[0].port.flags = 0;
1440 up[0].port.line = (inst * 2) + 0;
1441 up[0].port.dev = &op->dev;
1442 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A;
1443 up[0].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNZILOG_CONSOLE);
1444 if (keyboard_mouse)
1445 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB;
1446 sunzilog_init_hw(&up[0]);
1447
1448 /* Channel B */
1449 up[1].port.mapbase = op->resource[0].start + 0x04;
1450 up[1].port.membase = (void __iomem *) &rp->channelB;
1451 up[1].port.iotype = UPIO_MEM;
1452 up[1].port.irq = op->archdata.irqs[0];
1453 up[1].port.uartclk = ZS_CLOCK;
1454 up[1].port.fifosize = 1;
1455 up[1].port.ops = &sunzilog_pops;
1456 up[1].port.type = PORT_SUNZILOG;
1457 up[1].port.flags = 0;
1458 up[1].port.line = (inst * 2) + 1;
1459 up[1].port.dev = &op->dev;
1460 up[1].flags |= 0;
1461 up[1].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNZILOG_CONSOLE);
1462 if (keyboard_mouse)
1463 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE;
1464 sunzilog_init_hw(&up[1]);
1465
1466 if (!keyboard_mouse) {
1467 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1468 &sunzilog_reg, up[0].port.line,
1469 false))
1470 up->flags |= SUNZILOG_FLAG_IS_CONS;
1471 err = uart_add_one_port(&sunzilog_reg, &up[0].port);
1472 if (err) {
1473 of_iounmap(&op->resource[0],
1474 rp, sizeof(struct zilog_layout));
1475 return err;
1476 }
1477 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1478 &sunzilog_reg, up[1].port.line,
1479 false))
1480 up->flags |= SUNZILOG_FLAG_IS_CONS;
1481 err = uart_add_one_port(&sunzilog_reg, &up[1].port);
1482 if (err) {
1483 uart_remove_one_port(&sunzilog_reg, &up[0].port);
1484 of_iounmap(&op->resource[0],
1485 rp, sizeof(struct zilog_layout));
1486 return err;
1487 }
1488 uart_inst++;
1489 } else {
1490 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) "
1491 "is a %s\n",
1492 dev_name(&op->dev),
1493 (unsigned long long) up[0].port.mapbase,
1494 op->archdata.irqs[0], sunzilog_type(&up[0].port));
1495 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) "
1496 "is a %s\n",
1497 dev_name(&op->dev),
1498 (unsigned long long) up[1].port.mapbase,
1499 op->archdata.irqs[0], sunzilog_type(&up[1].port));
1500 kbm_inst++;
1501 }
1502
1503 platform_set_drvdata(op, &up[0]);
1504
1505 return 0;
1506}
1507
1508static void zs_remove_one(struct uart_sunzilog_port *up)
1509{
1510 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) {
1511#ifdef CONFIG_SERIO
1512 serio_unregister_port(&up->serio);
1513#endif
1514 } else
1515 uart_remove_one_port(&sunzilog_reg, &up->port);
1516}
1517
1518static int zs_remove(struct platform_device *op)
1519{
1520 struct uart_sunzilog_port *up = platform_get_drvdata(op);
1521 struct zilog_layout __iomem *regs;
1522
1523 zs_remove_one(&up[0]);
1524 zs_remove_one(&up[1]);
1525
1526 regs = sunzilog_chip_regs[up[0].port.line / 2];
1527 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout));
1528
1529 return 0;
1530}
1531
1532static const struct of_device_id zs_match[] = {
1533 {
1534 .name = "zs",
1535 },
1536 {},
1537};
1538MODULE_DEVICE_TABLE(of, zs_match);
1539
1540static struct platform_driver zs_driver = {
1541 .driver = {
1542 .name = "zs",
1543 .of_match_table = zs_match,
1544 },
1545 .probe = zs_probe,
1546 .remove = zs_remove,
1547};
1548
1549static int __init sunzilog_init(void)
1550{
1551 struct device_node *dp;
1552 int err;
1553 int num_keybms = 0;
1554 int num_sunzilog = 0;
1555
1556 for_each_node_by_name(dp, "zs") {
1557 num_sunzilog++;
1558 if (of_find_property(dp, "keyboard", NULL))
1559 num_keybms++;
1560 }
1561
1562 if (num_sunzilog) {
1563 err = sunzilog_alloc_tables(num_sunzilog);
1564 if (err)
1565 goto out;
1566
1567 uart_chip_count = num_sunzilog - num_keybms;
1568
1569 err = sunserial_register_minors(&sunzilog_reg,
1570 uart_chip_count * 2);
1571 if (err)
1572 goto out_free_tables;
1573 }
1574
1575 err = platform_driver_register(&zs_driver);
1576 if (err)
1577 goto out_unregister_uart;
1578
1579 if (zilog_irq) {
1580 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1581 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
1582 "zs", sunzilog_irq_chain);
1583 if (err)
1584 goto out_unregister_driver;
1585
1586 /* Enable Interrupts */
1587 while (up) {
1588 struct zilog_channel __iomem *channel;
1589
1590 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
1591 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1592 up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
1593 up->curregs[R9] |= MIE;
1594 write_zsreg(channel, R9, up->curregs[R9]);
1595 up = up->next;
1596 }
1597 }
1598
1599out:
1600 return err;
1601
1602out_unregister_driver:
1603 platform_driver_unregister(&zs_driver);
1604
1605out_unregister_uart:
1606 if (num_sunzilog) {
1607 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog);
1608 sunzilog_reg.cons = NULL;
1609 }
1610
1611out_free_tables:
1612 sunzilog_free_tables();
1613 goto out;
1614}
1615
1616static void __exit sunzilog_exit(void)
1617{
1618 platform_driver_unregister(&zs_driver);
1619
1620 if (zilog_irq) {
1621 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1622
1623 /* Disable Interrupts */
1624 while (up) {
1625 struct zilog_channel __iomem *channel;
1626
1627 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
1628 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1629 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
1630 up->curregs[R9] &= ~MIE;
1631 write_zsreg(channel, R9, up->curregs[R9]);
1632 up = up->next;
1633 }
1634
1635 free_irq(zilog_irq, sunzilog_irq_chain);
1636 zilog_irq = 0;
1637 }
1638
1639 if (sunzilog_reg.nr) {
1640 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr);
1641 sunzilog_free_tables();
1642 }
1643}
1644
1645module_init(sunzilog_init);
1646module_exit(sunzilog_exit);
1647
1648MODULE_AUTHOR("David S. Miller");
1649MODULE_DESCRIPTION("Sun Zilog serial port driver");
1650MODULE_VERSION("2.0");
1651MODULE_LICENSE("GPL");