Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Freescale QUICC Engine UART device driver
4 *
5 * Author: Timur Tabi <timur@freescale.com>
6 *
7 * Copyright 2007 Freescale Semiconductor, Inc.
8 *
9 * This driver adds support for UART devices via Freescale's QUICC Engine
10 * found on some Freescale SOCs.
11 *
12 * If Soft-UART support is needed but not already present, then this driver
13 * will request and upload the "Soft-UART" microcode upon probe. The
14 * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin, where "X"
15 * is the name of the SOC (e.g. 8323), and YZ is the revision of the SOC,
16 * (e.g. "11" for 1.1).
17 */
18
19#include <linux/module.h>
20#include <linux/serial.h>
21#include <linux/serial_core.h>
22#include <linux/slab.h>
23#include <linux/tty.h>
24#include <linux/tty_flip.h>
25#include <linux/io.h>
26#include <linux/of_address.h>
27#include <linux/of_irq.h>
28#include <linux/of_platform.h>
29#include <linux/dma-mapping.h>
30
31#include <linux/fs_uart_pd.h>
32#include <soc/fsl/qe/ucc_slow.h>
33
34#include <linux/firmware.h>
35#include <asm/reg.h>
36
37/*
38 * The GUMR flag for Soft UART. This would normally be defined in qe.h,
39 * but Soft-UART is a hack and we want to keep everything related to it in
40 * this file.
41 */
42#define UCC_SLOW_GUMR_H_SUART 0x00004000 /* Soft-UART */
43
44/*
45 * soft_uart is 1 if we need to use Soft-UART mode
46 */
47static int soft_uart;
48/*
49 * firmware_loaded is 1 if the firmware has been loaded, 0 otherwise.
50 */
51static int firmware_loaded;
52
53/* Enable this macro to configure all serial ports in internal loopback
54 mode */
55/* #define LOOPBACK */
56
57/* The major and minor device numbers are defined in
58 * http://www.lanana.org/docs/device-list/devices-2.6+.txt. For the QE
59 * UART, we have major number 204 and minor numbers 46 - 49, which are the
60 * same as for the CPM2. This decision was made because no Freescale part
61 * has both a CPM and a QE.
62 */
63#define SERIAL_QE_MAJOR 204
64#define SERIAL_QE_MINOR 46
65
66/* Since we only have minor numbers 46 - 49, there is a hard limit of 4 ports */
67#define UCC_MAX_UART 4
68
69/* The number of buffer descriptors for receiving characters. */
70#define RX_NUM_FIFO 4
71
72/* The number of buffer descriptors for transmitting characters. */
73#define TX_NUM_FIFO 4
74
75/* The maximum size of the character buffer for a single RX BD. */
76#define RX_BUF_SIZE 32
77
78/* The maximum size of the character buffer for a single TX BD. */
79#define TX_BUF_SIZE 32
80
81/*
82 * The number of jiffies to wait after receiving a close command before the
83 * device is actually closed. This allows the last few characters to be
84 * sent over the wire.
85 */
86#define UCC_WAIT_CLOSING 100
87
88struct ucc_uart_pram {
89 struct ucc_slow_pram common;
90 u8 res1[8]; /* reserved */
91 __be16 maxidl; /* Maximum idle chars */
92 __be16 idlc; /* temp idle counter */
93 __be16 brkcr; /* Break count register */
94 __be16 parec; /* receive parity error counter */
95 __be16 frmec; /* receive framing error counter */
96 __be16 nosec; /* receive noise counter */
97 __be16 brkec; /* receive break condition counter */
98 __be16 brkln; /* last received break length */
99 __be16 uaddr[2]; /* UART address character 1 & 2 */
100 __be16 rtemp; /* Temp storage */
101 __be16 toseq; /* Transmit out of sequence char */
102 __be16 cchars[8]; /* control characters 1-8 */
103 __be16 rccm; /* receive control character mask */
104 __be16 rccr; /* receive control character register */
105 __be16 rlbc; /* receive last break character */
106 __be16 res2; /* reserved */
107 __be32 res3; /* reserved, should be cleared */
108 u8 res4; /* reserved, should be cleared */
109 u8 res5[3]; /* reserved, should be cleared */
110 __be32 res6; /* reserved, should be cleared */
111 __be32 res7; /* reserved, should be cleared */
112 __be32 res8; /* reserved, should be cleared */
113 __be32 res9; /* reserved, should be cleared */
114 __be32 res10; /* reserved, should be cleared */
115 __be32 res11; /* reserved, should be cleared */
116 __be32 res12; /* reserved, should be cleared */
117 __be32 res13; /* reserved, should be cleared */
118/* The rest is for Soft-UART only */
119 __be16 supsmr; /* 0x90, Shadow UPSMR */
120 __be16 res92; /* 0x92, reserved, initialize to 0 */
121 __be32 rx_state; /* 0x94, RX state, initialize to 0 */
122 __be32 rx_cnt; /* 0x98, RX count, initialize to 0 */
123 u8 rx_length; /* 0x9C, Char length, set to 1+CL+PEN+1+SL */
124 u8 rx_bitmark; /* 0x9D, reserved, initialize to 0 */
125 u8 rx_temp_dlst_qe; /* 0x9E, reserved, initialize to 0 */
126 u8 res14[0xBC - 0x9F]; /* reserved */
127 __be32 dump_ptr; /* 0xBC, Dump pointer */
128 __be32 rx_frame_rem; /* 0xC0, reserved, initialize to 0 */
129 u8 rx_frame_rem_size; /* 0xC4, reserved, initialize to 0 */
130 u8 tx_mode; /* 0xC5, mode, 0=AHDLC, 1=UART */
131 __be16 tx_state; /* 0xC6, TX state */
132 u8 res15[0xD0 - 0xC8]; /* reserved */
133 __be32 resD0; /* 0xD0, reserved, initialize to 0 */
134 u8 resD4; /* 0xD4, reserved, initialize to 0 */
135 __be16 resD5; /* 0xD5, reserved, initialize to 0 */
136} __attribute__ ((packed));
137
138/* SUPSMR definitions, for Soft-UART only */
139#define UCC_UART_SUPSMR_SL 0x8000
140#define UCC_UART_SUPSMR_RPM_MASK 0x6000
141#define UCC_UART_SUPSMR_RPM_ODD 0x0000
142#define UCC_UART_SUPSMR_RPM_LOW 0x2000
143#define UCC_UART_SUPSMR_RPM_EVEN 0x4000
144#define UCC_UART_SUPSMR_RPM_HIGH 0x6000
145#define UCC_UART_SUPSMR_PEN 0x1000
146#define UCC_UART_SUPSMR_TPM_MASK 0x0C00
147#define UCC_UART_SUPSMR_TPM_ODD 0x0000
148#define UCC_UART_SUPSMR_TPM_LOW 0x0400
149#define UCC_UART_SUPSMR_TPM_EVEN 0x0800
150#define UCC_UART_SUPSMR_TPM_HIGH 0x0C00
151#define UCC_UART_SUPSMR_FRZ 0x0100
152#define UCC_UART_SUPSMR_UM_MASK 0x00c0
153#define UCC_UART_SUPSMR_UM_NORMAL 0x0000
154#define UCC_UART_SUPSMR_UM_MAN_MULTI 0x0040
155#define UCC_UART_SUPSMR_UM_AUTO_MULTI 0x00c0
156#define UCC_UART_SUPSMR_CL_MASK 0x0030
157#define UCC_UART_SUPSMR_CL_8 0x0030
158#define UCC_UART_SUPSMR_CL_7 0x0020
159#define UCC_UART_SUPSMR_CL_6 0x0010
160#define UCC_UART_SUPSMR_CL_5 0x0000
161
162#define UCC_UART_TX_STATE_AHDLC 0x00
163#define UCC_UART_TX_STATE_UART 0x01
164#define UCC_UART_TX_STATE_X1 0x00
165#define UCC_UART_TX_STATE_X16 0x80
166
167#define UCC_UART_PRAM_ALIGNMENT 0x100
168
169#define UCC_UART_SIZE_OF_BD UCC_SLOW_SIZE_OF_BD
170#define NUM_CONTROL_CHARS 8
171
172/* Private per-port data structure */
173struct uart_qe_port {
174 struct uart_port port;
175 struct ucc_slow __iomem *uccp;
176 struct ucc_uart_pram __iomem *uccup;
177 struct ucc_slow_info us_info;
178 struct ucc_slow_private *us_private;
179 struct device_node *np;
180 unsigned int ucc_num; /* First ucc is 0, not 1 */
181
182 u16 rx_nrfifos;
183 u16 rx_fifosize;
184 u16 tx_nrfifos;
185 u16 tx_fifosize;
186 int wait_closing;
187 u32 flags;
188 struct qe_bd *rx_bd_base;
189 struct qe_bd *rx_cur;
190 struct qe_bd *tx_bd_base;
191 struct qe_bd *tx_cur;
192 unsigned char *tx_buf;
193 unsigned char *rx_buf;
194 void *bd_virt; /* virtual address of the BD buffers */
195 dma_addr_t bd_dma_addr; /* bus address of the BD buffers */
196 unsigned int bd_size; /* size of BD buffer space */
197};
198
199static struct uart_driver ucc_uart_driver = {
200 .owner = THIS_MODULE,
201 .driver_name = "ucc_uart",
202 .dev_name = "ttyQE",
203 .major = SERIAL_QE_MAJOR,
204 .minor = SERIAL_QE_MINOR,
205 .nr = UCC_MAX_UART,
206};
207
208/*
209 * Virtual to physical address translation.
210 *
211 * Given the virtual address for a character buffer, this function returns
212 * the physical (DMA) equivalent.
213 */
214static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port)
215{
216 if (likely((addr >= qe_port->bd_virt)) &&
217 (addr < (qe_port->bd_virt + qe_port->bd_size)))
218 return qe_port->bd_dma_addr + (addr - qe_port->bd_virt);
219
220 /* something nasty happened */
221 printk(KERN_ERR "%s: addr=%p\n", __func__, addr);
222 BUG();
223 return 0;
224}
225
226/*
227 * Physical to virtual address translation.
228 *
229 * Given the physical (DMA) address for a character buffer, this function
230 * returns the virtual equivalent.
231 */
232static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port)
233{
234 /* sanity check */
235 if (likely((addr >= qe_port->bd_dma_addr) &&
236 (addr < (qe_port->bd_dma_addr + qe_port->bd_size))))
237 return qe_port->bd_virt + (addr - qe_port->bd_dma_addr);
238
239 /* something nasty happened */
240 printk(KERN_ERR "%s: addr=%llx\n", __func__, (u64)addr);
241 BUG();
242 return NULL;
243}
244
245/*
246 * Return 1 if the QE is done transmitting all buffers for this port
247 *
248 * This function scans each BD in sequence. If we find a BD that is not
249 * ready (READY=1), then we return 0 indicating that the QE is still sending
250 * data. If we reach the last BD (WRAP=1), then we know we've scanned
251 * the entire list, and all BDs are done.
252 */
253static unsigned int qe_uart_tx_empty(struct uart_port *port)
254{
255 struct uart_qe_port *qe_port =
256 container_of(port, struct uart_qe_port, port);
257 struct qe_bd *bdp = qe_port->tx_bd_base;
258
259 while (1) {
260 if (in_be16(&bdp->status) & BD_SC_READY)
261 /* This BD is not done, so return "not done" */
262 return 0;
263
264 if (in_be16(&bdp->status) & BD_SC_WRAP)
265 /*
266 * This BD is done and it's the last one, so return
267 * "done"
268 */
269 return 1;
270
271 bdp++;
272 }
273}
274
275/*
276 * Set the modem control lines
277 *
278 * Although the QE can control the modem control lines (e.g. CTS), we
279 * don't need that support. This function must exist, however, otherwise
280 * the kernel will panic.
281 */
282void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
283{
284}
285
286/*
287 * Get the current modem control line status
288 *
289 * Although the QE can control the modem control lines (e.g. CTS), this
290 * driver currently doesn't support that, so we always return Carrier
291 * Detect, Data Set Ready, and Clear To Send.
292 */
293static unsigned int qe_uart_get_mctrl(struct uart_port *port)
294{
295 return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
296}
297
298/*
299 * Disable the transmit interrupt.
300 *
301 * Although this function is called "stop_tx", it does not actually stop
302 * transmission of data. Instead, it tells the QE to not generate an
303 * interrupt when the UCC is finished sending characters.
304 */
305static void qe_uart_stop_tx(struct uart_port *port)
306{
307 struct uart_qe_port *qe_port =
308 container_of(port, struct uart_qe_port, port);
309
310 clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
311}
312
313/*
314 * Transmit as many characters to the HW as possible.
315 *
316 * This function will attempt to stuff of all the characters from the
317 * kernel's transmit buffer into TX BDs.
318 *
319 * A return value of non-zero indicates that it successfully stuffed all
320 * characters from the kernel buffer.
321 *
322 * A return value of zero indicates that there are still characters in the
323 * kernel's buffer that have not been transmitted, but there are no more BDs
324 * available. This function should be called again after a BD has been made
325 * available.
326 */
327static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
328{
329 struct qe_bd *bdp;
330 unsigned char *p;
331 unsigned int count;
332 struct uart_port *port = &qe_port->port;
333 struct circ_buf *xmit = &port->state->xmit;
334
335 bdp = qe_port->rx_cur;
336
337 /* Handle xon/xoff */
338 if (port->x_char) {
339 /* Pick next descriptor and fill from buffer */
340 bdp = qe_port->tx_cur;
341
342 p = qe2cpu_addr(bdp->buf, qe_port);
343
344 *p++ = port->x_char;
345 out_be16(&bdp->length, 1);
346 setbits16(&bdp->status, BD_SC_READY);
347 /* Get next BD. */
348 if (in_be16(&bdp->status) & BD_SC_WRAP)
349 bdp = qe_port->tx_bd_base;
350 else
351 bdp++;
352 qe_port->tx_cur = bdp;
353
354 port->icount.tx++;
355 port->x_char = 0;
356 return 1;
357 }
358
359 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
360 qe_uart_stop_tx(port);
361 return 0;
362 }
363
364 /* Pick next descriptor and fill from buffer */
365 bdp = qe_port->tx_cur;
366
367 while (!(in_be16(&bdp->status) & BD_SC_READY) &&
368 (xmit->tail != xmit->head)) {
369 count = 0;
370 p = qe2cpu_addr(bdp->buf, qe_port);
371 while (count < qe_port->tx_fifosize) {
372 *p++ = xmit->buf[xmit->tail];
373 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
374 port->icount.tx++;
375 count++;
376 if (xmit->head == xmit->tail)
377 break;
378 }
379
380 out_be16(&bdp->length, count);
381 setbits16(&bdp->status, BD_SC_READY);
382
383 /* Get next BD. */
384 if (in_be16(&bdp->status) & BD_SC_WRAP)
385 bdp = qe_port->tx_bd_base;
386 else
387 bdp++;
388 }
389 qe_port->tx_cur = bdp;
390
391 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
392 uart_write_wakeup(port);
393
394 if (uart_circ_empty(xmit)) {
395 /* The kernel buffer is empty, so turn off TX interrupts. We
396 don't need to be told when the QE is finished transmitting
397 the data. */
398 qe_uart_stop_tx(port);
399 return 0;
400 }
401
402 return 1;
403}
404
405/*
406 * Start transmitting data
407 *
408 * This function will start transmitting any available data, if the port
409 * isn't already transmitting data.
410 */
411static void qe_uart_start_tx(struct uart_port *port)
412{
413 struct uart_qe_port *qe_port =
414 container_of(port, struct uart_qe_port, port);
415
416 /* If we currently are transmitting, then just return */
417 if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
418 return;
419
420 /* Otherwise, pump the port and start transmission */
421 if (qe_uart_tx_pump(qe_port))
422 setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
423}
424
425/*
426 * Stop transmitting data
427 */
428static void qe_uart_stop_rx(struct uart_port *port)
429{
430 struct uart_qe_port *qe_port =
431 container_of(port, struct uart_qe_port, port);
432
433 clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
434}
435
436/* Start or stop sending break signal
437 *
438 * This function controls the sending of a break signal. If break_state=1,
439 * then we start sending a break signal. If break_state=0, then we stop
440 * sending the break signal.
441 */
442static void qe_uart_break_ctl(struct uart_port *port, int break_state)
443{
444 struct uart_qe_port *qe_port =
445 container_of(port, struct uart_qe_port, port);
446
447 if (break_state)
448 ucc_slow_stop_tx(qe_port->us_private);
449 else
450 ucc_slow_restart_tx(qe_port->us_private);
451}
452
453/* ISR helper function for receiving character.
454 *
455 * This function is called by the ISR to handling receiving characters
456 */
457static void qe_uart_int_rx(struct uart_qe_port *qe_port)
458{
459 int i;
460 unsigned char ch, *cp;
461 struct uart_port *port = &qe_port->port;
462 struct tty_port *tport = &port->state->port;
463 struct qe_bd *bdp;
464 u16 status;
465 unsigned int flg;
466
467 /* Just loop through the closed BDs and copy the characters into
468 * the buffer.
469 */
470 bdp = qe_port->rx_cur;
471 while (1) {
472 status = in_be16(&bdp->status);
473
474 /* If this one is empty, then we assume we've read them all */
475 if (status & BD_SC_EMPTY)
476 break;
477
478 /* get number of characters, and check space in RX buffer */
479 i = in_be16(&bdp->length);
480
481 /* If we don't have enough room in RX buffer for the entire BD,
482 * then we try later, which will be the next RX interrupt.
483 */
484 if (tty_buffer_request_room(tport, i) < i) {
485 dev_dbg(port->dev, "ucc-uart: no room in RX buffer\n");
486 return;
487 }
488
489 /* get pointer */
490 cp = qe2cpu_addr(bdp->buf, qe_port);
491
492 /* loop through the buffer */
493 while (i-- > 0) {
494 ch = *cp++;
495 port->icount.rx++;
496 flg = TTY_NORMAL;
497
498 if (!i && status &
499 (BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV))
500 goto handle_error;
501 if (uart_handle_sysrq_char(port, ch))
502 continue;
503
504error_return:
505 tty_insert_flip_char(tport, ch, flg);
506
507 }
508
509 /* This BD is ready to be used again. Clear status. get next */
510 clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR |
511 BD_SC_OV | BD_SC_ID, BD_SC_EMPTY);
512 if (in_be16(&bdp->status) & BD_SC_WRAP)
513 bdp = qe_port->rx_bd_base;
514 else
515 bdp++;
516
517 }
518
519 /* Write back buffer pointer */
520 qe_port->rx_cur = bdp;
521
522 /* Activate BH processing */
523 tty_flip_buffer_push(tport);
524
525 return;
526
527 /* Error processing */
528
529handle_error:
530 /* Statistics */
531 if (status & BD_SC_BR)
532 port->icount.brk++;
533 if (status & BD_SC_PR)
534 port->icount.parity++;
535 if (status & BD_SC_FR)
536 port->icount.frame++;
537 if (status & BD_SC_OV)
538 port->icount.overrun++;
539
540 /* Mask out ignored conditions */
541 status &= port->read_status_mask;
542
543 /* Handle the remaining ones */
544 if (status & BD_SC_BR)
545 flg = TTY_BREAK;
546 else if (status & BD_SC_PR)
547 flg = TTY_PARITY;
548 else if (status & BD_SC_FR)
549 flg = TTY_FRAME;
550
551 /* Overrun does not affect the current character ! */
552 if (status & BD_SC_OV)
553 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
554#ifdef SUPPORT_SYSRQ
555 port->sysrq = 0;
556#endif
557 goto error_return;
558}
559
560/* Interrupt handler
561 *
562 * This interrupt handler is called after a BD is processed.
563 */
564static irqreturn_t qe_uart_int(int irq, void *data)
565{
566 struct uart_qe_port *qe_port = (struct uart_qe_port *) data;
567 struct ucc_slow __iomem *uccp = qe_port->uccp;
568 u16 events;
569
570 /* Clear the interrupts */
571 events = in_be16(&uccp->ucce);
572 out_be16(&uccp->ucce, events);
573
574 if (events & UCC_UART_UCCE_BRKE)
575 uart_handle_break(&qe_port->port);
576
577 if (events & UCC_UART_UCCE_RX)
578 qe_uart_int_rx(qe_port);
579
580 if (events & UCC_UART_UCCE_TX)
581 qe_uart_tx_pump(qe_port);
582
583 return events ? IRQ_HANDLED : IRQ_NONE;
584}
585
586/* Initialize buffer descriptors
587 *
588 * This function initializes all of the RX and TX buffer descriptors.
589 */
590static void qe_uart_initbd(struct uart_qe_port *qe_port)
591{
592 int i;
593 void *bd_virt;
594 struct qe_bd *bdp;
595
596 /* Set the physical address of the host memory buffers in the buffer
597 * descriptors, and the virtual address for us to work with.
598 */
599 bd_virt = qe_port->bd_virt;
600 bdp = qe_port->rx_bd_base;
601 qe_port->rx_cur = qe_port->rx_bd_base;
602 for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) {
603 out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT);
604 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
605 out_be16(&bdp->length, 0);
606 bd_virt += qe_port->rx_fifosize;
607 bdp++;
608 }
609
610 /* */
611 out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT);
612 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
613 out_be16(&bdp->length, 0);
614
615 /* Set the physical address of the host memory
616 * buffers in the buffer descriptors, and the
617 * virtual address for us to work with.
618 */
619 bd_virt = qe_port->bd_virt +
620 L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
621 qe_port->tx_cur = qe_port->tx_bd_base;
622 bdp = qe_port->tx_bd_base;
623 for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) {
624 out_be16(&bdp->status, BD_SC_INTRPT);
625 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
626 out_be16(&bdp->length, 0);
627 bd_virt += qe_port->tx_fifosize;
628 bdp++;
629 }
630
631 /* Loopback requires the preamble bit to be set on the first TX BD */
632#ifdef LOOPBACK
633 setbits16(&qe_port->tx_cur->status, BD_SC_P);
634#endif
635
636 out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT);
637 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
638 out_be16(&bdp->length, 0);
639}
640
641/*
642 * Initialize a UCC for UART.
643 *
644 * This function configures a given UCC to be used as a UART device. Basic
645 * UCC initialization is handled in qe_uart_request_port(). This function
646 * does all the UART-specific stuff.
647 */
648static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
649{
650 u32 cecr_subblock;
651 struct ucc_slow __iomem *uccp = qe_port->uccp;
652 struct ucc_uart_pram *uccup = qe_port->uccup;
653
654 unsigned int i;
655
656 /* First, disable TX and RX in the UCC */
657 ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
658
659 /* Program the UCC UART parameter RAM */
660 out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
661 out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
662 out_be16(&uccup->common.mrblr, qe_port->rx_fifosize);
663 out_be16(&uccup->maxidl, 0x10);
664 out_be16(&uccup->brkcr, 1);
665 out_be16(&uccup->parec, 0);
666 out_be16(&uccup->frmec, 0);
667 out_be16(&uccup->nosec, 0);
668 out_be16(&uccup->brkec, 0);
669 out_be16(&uccup->uaddr[0], 0);
670 out_be16(&uccup->uaddr[1], 0);
671 out_be16(&uccup->toseq, 0);
672 for (i = 0; i < 8; i++)
673 out_be16(&uccup->cchars[i], 0xC000);
674 out_be16(&uccup->rccm, 0xc0ff);
675
676 /* Configure the GUMR registers for UART */
677 if (soft_uart) {
678 /* Soft-UART requires a 1X multiplier for TX */
679 clrsetbits_be32(&uccp->gumr_l,
680 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
681 UCC_SLOW_GUMR_L_RDCR_MASK,
682 UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 |
683 UCC_SLOW_GUMR_L_RDCR_16);
684
685 clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
686 UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
687 } else {
688 clrsetbits_be32(&uccp->gumr_l,
689 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
690 UCC_SLOW_GUMR_L_RDCR_MASK,
691 UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 |
692 UCC_SLOW_GUMR_L_RDCR_16);
693
694 clrsetbits_be32(&uccp->gumr_h,
695 UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
696 UCC_SLOW_GUMR_H_RFW);
697 }
698
699#ifdef LOOPBACK
700 clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
701 UCC_SLOW_GUMR_L_DIAG_LOOP);
702 clrsetbits_be32(&uccp->gumr_h,
703 UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
704 UCC_SLOW_GUMR_H_CDS);
705#endif
706
707 /* Disable rx interrupts and clear all pending events. */
708 out_be16(&uccp->uccm, 0);
709 out_be16(&uccp->ucce, 0xffff);
710 out_be16(&uccp->udsr, 0x7e7e);
711
712 /* Initialize UPSMR */
713 out_be16(&uccp->upsmr, 0);
714
715 if (soft_uart) {
716 out_be16(&uccup->supsmr, 0x30);
717 out_be16(&uccup->res92, 0);
718 out_be32(&uccup->rx_state, 0);
719 out_be32(&uccup->rx_cnt, 0);
720 out_8(&uccup->rx_bitmark, 0);
721 out_8(&uccup->rx_length, 10);
722 out_be32(&uccup->dump_ptr, 0x4000);
723 out_8(&uccup->rx_temp_dlst_qe, 0);
724 out_be32(&uccup->rx_frame_rem, 0);
725 out_8(&uccup->rx_frame_rem_size, 0);
726 /* Soft-UART requires TX to be 1X */
727 out_8(&uccup->tx_mode,
728 UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1);
729 out_be16(&uccup->tx_state, 0);
730 out_8(&uccup->resD4, 0);
731 out_be16(&uccup->resD5, 0);
732
733 /* Set UART mode.
734 * Enable receive and transmit.
735 */
736
737 /* From the microcode errata:
738 * 1.GUMR_L register, set mode=0010 (QMC).
739 * 2.Set GUMR_H[17] bit. (UART/AHDLC mode).
740 * 3.Set GUMR_H[19:20] (Transparent mode)
741 * 4.Clear GUMR_H[26] (RFW)
742 * ...
743 * 6.Receiver must use 16x over sampling
744 */
745 clrsetbits_be32(&uccp->gumr_l,
746 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
747 UCC_SLOW_GUMR_L_RDCR_MASK,
748 UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 |
749 UCC_SLOW_GUMR_L_RDCR_16);
750
751 clrsetbits_be32(&uccp->gumr_h,
752 UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
753 UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX |
754 UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
755
756#ifdef LOOPBACK
757 clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
758 UCC_SLOW_GUMR_L_DIAG_LOOP);
759 clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP |
760 UCC_SLOW_GUMR_H_CDS);
761#endif
762
763 cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
764 qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
765 QE_CR_PROTOCOL_UNSPECIFIED, 0);
766 } else {
767 cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
768 qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
769 QE_CR_PROTOCOL_UART, 0);
770 }
771}
772
773/*
774 * Initialize the port.
775 */
776static int qe_uart_startup(struct uart_port *port)
777{
778 struct uart_qe_port *qe_port =
779 container_of(port, struct uart_qe_port, port);
780 int ret;
781
782 /*
783 * If we're using Soft-UART mode, then we need to make sure the
784 * firmware has been uploaded first.
785 */
786 if (soft_uart && !firmware_loaded) {
787 dev_err(port->dev, "Soft-UART firmware not uploaded\n");
788 return -ENODEV;
789 }
790
791 qe_uart_initbd(qe_port);
792 qe_uart_init_ucc(qe_port);
793
794 /* Install interrupt handler. */
795 ret = request_irq(port->irq, qe_uart_int, IRQF_SHARED, "ucc-uart",
796 qe_port);
797 if (ret) {
798 dev_err(port->dev, "could not claim IRQ %u\n", port->irq);
799 return ret;
800 }
801
802 /* Startup rx-int */
803 setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
804 ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX);
805
806 return 0;
807}
808
809/*
810 * Shutdown the port.
811 */
812static void qe_uart_shutdown(struct uart_port *port)
813{
814 struct uart_qe_port *qe_port =
815 container_of(port, struct uart_qe_port, port);
816 struct ucc_slow __iomem *uccp = qe_port->uccp;
817 unsigned int timeout = 20;
818
819 /* Disable RX and TX */
820
821 /* Wait for all the BDs marked sent */
822 while (!qe_uart_tx_empty(port)) {
823 if (!--timeout) {
824 dev_warn(port->dev, "shutdown timeout\n");
825 break;
826 }
827 set_current_state(TASK_UNINTERRUPTIBLE);
828 schedule_timeout(2);
829 }
830
831 if (qe_port->wait_closing) {
832 /* Wait a bit longer */
833 set_current_state(TASK_UNINTERRUPTIBLE);
834 schedule_timeout(qe_port->wait_closing);
835 }
836
837 /* Stop uarts */
838 ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
839 clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
840
841 /* Shut them really down and reinit buffer descriptors */
842 ucc_slow_graceful_stop_tx(qe_port->us_private);
843 qe_uart_initbd(qe_port);
844
845 free_irq(port->irq, qe_port);
846}
847
848/*
849 * Set the serial port parameters.
850 */
851static void qe_uart_set_termios(struct uart_port *port,
852 struct ktermios *termios, struct ktermios *old)
853{
854 struct uart_qe_port *qe_port =
855 container_of(port, struct uart_qe_port, port);
856 struct ucc_slow __iomem *uccp = qe_port->uccp;
857 unsigned int baud;
858 unsigned long flags;
859 u16 upsmr = in_be16(&uccp->upsmr);
860 struct ucc_uart_pram __iomem *uccup = qe_port->uccup;
861 u16 supsmr = in_be16(&uccup->supsmr);
862 u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */
863
864 /* Character length programmed into the mode register is the
865 * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
866 * 1 or 2 stop bits, minus 1.
867 * The value 'bits' counts this for us.
868 */
869
870 /* byte size */
871 upsmr &= UCC_UART_UPSMR_CL_MASK;
872 supsmr &= UCC_UART_SUPSMR_CL_MASK;
873
874 switch (termios->c_cflag & CSIZE) {
875 case CS5:
876 upsmr |= UCC_UART_UPSMR_CL_5;
877 supsmr |= UCC_UART_SUPSMR_CL_5;
878 char_length += 5;
879 break;
880 case CS6:
881 upsmr |= UCC_UART_UPSMR_CL_6;
882 supsmr |= UCC_UART_SUPSMR_CL_6;
883 char_length += 6;
884 break;
885 case CS7:
886 upsmr |= UCC_UART_UPSMR_CL_7;
887 supsmr |= UCC_UART_SUPSMR_CL_7;
888 char_length += 7;
889 break;
890 default: /* case CS8 */
891 upsmr |= UCC_UART_UPSMR_CL_8;
892 supsmr |= UCC_UART_SUPSMR_CL_8;
893 char_length += 8;
894 break;
895 }
896
897 /* If CSTOPB is set, we want two stop bits */
898 if (termios->c_cflag & CSTOPB) {
899 upsmr |= UCC_UART_UPSMR_SL;
900 supsmr |= UCC_UART_SUPSMR_SL;
901 char_length++; /* + SL */
902 }
903
904 if (termios->c_cflag & PARENB) {
905 upsmr |= UCC_UART_UPSMR_PEN;
906 supsmr |= UCC_UART_SUPSMR_PEN;
907 char_length++; /* + PEN */
908
909 if (!(termios->c_cflag & PARODD)) {
910 upsmr &= ~(UCC_UART_UPSMR_RPM_MASK |
911 UCC_UART_UPSMR_TPM_MASK);
912 upsmr |= UCC_UART_UPSMR_RPM_EVEN |
913 UCC_UART_UPSMR_TPM_EVEN;
914 supsmr &= ~(UCC_UART_SUPSMR_RPM_MASK |
915 UCC_UART_SUPSMR_TPM_MASK);
916 supsmr |= UCC_UART_SUPSMR_RPM_EVEN |
917 UCC_UART_SUPSMR_TPM_EVEN;
918 }
919 }
920
921 /*
922 * Set up parity check flag
923 */
924 port->read_status_mask = BD_SC_EMPTY | BD_SC_OV;
925 if (termios->c_iflag & INPCK)
926 port->read_status_mask |= BD_SC_FR | BD_SC_PR;
927 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
928 port->read_status_mask |= BD_SC_BR;
929
930 /*
931 * Characters to ignore
932 */
933 port->ignore_status_mask = 0;
934 if (termios->c_iflag & IGNPAR)
935 port->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
936 if (termios->c_iflag & IGNBRK) {
937 port->ignore_status_mask |= BD_SC_BR;
938 /*
939 * If we're ignore parity and break indicators, ignore
940 * overruns too. (For real raw support).
941 */
942 if (termios->c_iflag & IGNPAR)
943 port->ignore_status_mask |= BD_SC_OV;
944 }
945 /*
946 * !!! ignore all characters if CREAD is not set
947 */
948 if ((termios->c_cflag & CREAD) == 0)
949 port->read_status_mask &= ~BD_SC_EMPTY;
950
951 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
952
953 /* Do we really need a spinlock here? */
954 spin_lock_irqsave(&port->lock, flags);
955
956 /* Update the per-port timeout. */
957 uart_update_timeout(port, termios->c_cflag, baud);
958
959 out_be16(&uccp->upsmr, upsmr);
960 if (soft_uart) {
961 out_be16(&uccup->supsmr, supsmr);
962 out_8(&uccup->rx_length, char_length);
963
964 /* Soft-UART requires a 1X multiplier for TX */
965 qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
966 qe_setbrg(qe_port->us_info.tx_clock, baud, 1);
967 } else {
968 qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
969 qe_setbrg(qe_port->us_info.tx_clock, baud, 16);
970 }
971
972 spin_unlock_irqrestore(&port->lock, flags);
973}
974
975/*
976 * Return a pointer to a string that describes what kind of port this is.
977 */
978static const char *qe_uart_type(struct uart_port *port)
979{
980 return "QE";
981}
982
983/*
984 * Allocate any memory and I/O resources required by the port.
985 */
986static int qe_uart_request_port(struct uart_port *port)
987{
988 int ret;
989 struct uart_qe_port *qe_port =
990 container_of(port, struct uart_qe_port, port);
991 struct ucc_slow_info *us_info = &qe_port->us_info;
992 struct ucc_slow_private *uccs;
993 unsigned int rx_size, tx_size;
994 void *bd_virt;
995 dma_addr_t bd_dma_addr = 0;
996
997 ret = ucc_slow_init(us_info, &uccs);
998 if (ret) {
999 dev_err(port->dev, "could not initialize UCC%u\n",
1000 qe_port->ucc_num);
1001 return ret;
1002 }
1003
1004 qe_port->us_private = uccs;
1005 qe_port->uccp = uccs->us_regs;
1006 qe_port->uccup = (struct ucc_uart_pram *) uccs->us_pram;
1007 qe_port->rx_bd_base = uccs->rx_bd;
1008 qe_port->tx_bd_base = uccs->tx_bd;
1009
1010 /*
1011 * Allocate the transmit and receive data buffers.
1012 */
1013
1014 rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
1015 tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize);
1016
1017 bd_virt = dma_alloc_coherent(port->dev, rx_size + tx_size, &bd_dma_addr,
1018 GFP_KERNEL);
1019 if (!bd_virt) {
1020 dev_err(port->dev, "could not allocate buffer descriptors\n");
1021 return -ENOMEM;
1022 }
1023
1024 qe_port->bd_virt = bd_virt;
1025 qe_port->bd_dma_addr = bd_dma_addr;
1026 qe_port->bd_size = rx_size + tx_size;
1027
1028 qe_port->rx_buf = bd_virt;
1029 qe_port->tx_buf = qe_port->rx_buf + rx_size;
1030
1031 return 0;
1032}
1033
1034/*
1035 * Configure the port.
1036 *
1037 * We say we're a CPM-type port because that's mostly true. Once the device
1038 * is configured, this driver operates almost identically to the CPM serial
1039 * driver.
1040 */
1041static void qe_uart_config_port(struct uart_port *port, int flags)
1042{
1043 if (flags & UART_CONFIG_TYPE) {
1044 port->type = PORT_CPM;
1045 qe_uart_request_port(port);
1046 }
1047}
1048
1049/*
1050 * Release any memory and I/O resources that were allocated in
1051 * qe_uart_request_port().
1052 */
1053static void qe_uart_release_port(struct uart_port *port)
1054{
1055 struct uart_qe_port *qe_port =
1056 container_of(port, struct uart_qe_port, port);
1057 struct ucc_slow_private *uccs = qe_port->us_private;
1058
1059 dma_free_coherent(port->dev, qe_port->bd_size, qe_port->bd_virt,
1060 qe_port->bd_dma_addr);
1061
1062 ucc_slow_free(uccs);
1063}
1064
1065/*
1066 * Verify that the data in serial_struct is suitable for this device.
1067 */
1068static int qe_uart_verify_port(struct uart_port *port,
1069 struct serial_struct *ser)
1070{
1071 if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM)
1072 return -EINVAL;
1073
1074 if (ser->irq < 0 || ser->irq >= nr_irqs)
1075 return -EINVAL;
1076
1077 if (ser->baud_base < 9600)
1078 return -EINVAL;
1079
1080 return 0;
1081}
1082/* UART operations
1083 *
1084 * Details on these functions can be found in Documentation/driver-api/serial/driver.rst
1085 */
1086static const struct uart_ops qe_uart_pops = {
1087 .tx_empty = qe_uart_tx_empty,
1088 .set_mctrl = qe_uart_set_mctrl,
1089 .get_mctrl = qe_uart_get_mctrl,
1090 .stop_tx = qe_uart_stop_tx,
1091 .start_tx = qe_uart_start_tx,
1092 .stop_rx = qe_uart_stop_rx,
1093 .break_ctl = qe_uart_break_ctl,
1094 .startup = qe_uart_startup,
1095 .shutdown = qe_uart_shutdown,
1096 .set_termios = qe_uart_set_termios,
1097 .type = qe_uart_type,
1098 .release_port = qe_uart_release_port,
1099 .request_port = qe_uart_request_port,
1100 .config_port = qe_uart_config_port,
1101 .verify_port = qe_uart_verify_port,
1102};
1103
1104/*
1105 * Obtain the SOC model number and revision level
1106 *
1107 * This function parses the device tree to obtain the SOC model. It then
1108 * reads the SVR register to the revision.
1109 *
1110 * The device tree stores the SOC model two different ways.
1111 *
1112 * The new way is:
1113 *
1114 * cpu@0 {
1115 * compatible = "PowerPC,8323";
1116 * device_type = "cpu";
1117 * ...
1118 *
1119 *
1120 * The old way is:
1121 * PowerPC,8323@0 {
1122 * device_type = "cpu";
1123 * ...
1124 *
1125 * This code first checks the new way, and then the old way.
1126 */
1127static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l)
1128{
1129 struct device_node *np;
1130 const char *soc_string;
1131 unsigned int svr;
1132 unsigned int soc;
1133
1134 /* Find the CPU node */
1135 np = of_find_node_by_type(NULL, "cpu");
1136 if (!np)
1137 return 0;
1138 /* Find the compatible property */
1139 soc_string = of_get_property(np, "compatible", NULL);
1140 if (!soc_string)
1141 /* No compatible property, so try the name. */
1142 soc_string = np->name;
1143
1144 /* Extract the SOC number from the "PowerPC," string */
1145 if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc)
1146 return 0;
1147
1148 /* Get the revision from the SVR */
1149 svr = mfspr(SPRN_SVR);
1150 *rev_h = (svr >> 4) & 0xf;
1151 *rev_l = svr & 0xf;
1152
1153 return soc;
1154}
1155
1156/*
1157 * requst_firmware_nowait() callback function
1158 *
1159 * This function is called by the kernel when a firmware is made available,
1160 * or if it times out waiting for the firmware.
1161 */
1162static void uart_firmware_cont(const struct firmware *fw, void *context)
1163{
1164 struct qe_firmware *firmware;
1165 struct device *dev = context;
1166 int ret;
1167
1168 if (!fw) {
1169 dev_err(dev, "firmware not found\n");
1170 return;
1171 }
1172
1173 firmware = (struct qe_firmware *) fw->data;
1174
1175 if (firmware->header.length != fw->size) {
1176 dev_err(dev, "invalid firmware\n");
1177 goto out;
1178 }
1179
1180 ret = qe_upload_firmware(firmware);
1181 if (ret) {
1182 dev_err(dev, "could not load firmware\n");
1183 goto out;
1184 }
1185
1186 firmware_loaded = 1;
1187 out:
1188 release_firmware(fw);
1189}
1190
1191static int ucc_uart_probe(struct platform_device *ofdev)
1192{
1193 struct device_node *np = ofdev->dev.of_node;
1194 const unsigned int *iprop; /* Integer OF properties */
1195 const char *sprop; /* String OF properties */
1196 struct uart_qe_port *qe_port = NULL;
1197 struct resource res;
1198 int ret;
1199
1200 /*
1201 * Determine if we need Soft-UART mode
1202 */
1203 if (of_find_property(np, "soft-uart", NULL)) {
1204 dev_dbg(&ofdev->dev, "using Soft-UART mode\n");
1205 soft_uart = 1;
1206 }
1207
1208 /*
1209 * If we are using Soft-UART, determine if we need to upload the
1210 * firmware, too.
1211 */
1212 if (soft_uart) {
1213 struct qe_firmware_info *qe_fw_info;
1214
1215 qe_fw_info = qe_get_firmware_info();
1216
1217 /* Check if the firmware has been uploaded. */
1218 if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
1219 firmware_loaded = 1;
1220 } else {
1221 char filename[32];
1222 unsigned int soc;
1223 unsigned int rev_h;
1224 unsigned int rev_l;
1225
1226 soc = soc_info(&rev_h, &rev_l);
1227 if (!soc) {
1228 dev_err(&ofdev->dev, "unknown CPU model\n");
1229 return -ENXIO;
1230 }
1231 sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
1232 soc, rev_h, rev_l);
1233
1234 dev_info(&ofdev->dev, "waiting for firmware %s\n",
1235 filename);
1236
1237 /*
1238 * We call request_firmware_nowait instead of
1239 * request_firmware so that the driver can load and
1240 * initialize the ports without holding up the rest of
1241 * the kernel. If hotplug support is enabled in the
1242 * kernel, then we use it.
1243 */
1244 ret = request_firmware_nowait(THIS_MODULE,
1245 FW_ACTION_HOTPLUG, filename, &ofdev->dev,
1246 GFP_KERNEL, &ofdev->dev, uart_firmware_cont);
1247 if (ret) {
1248 dev_err(&ofdev->dev,
1249 "could not load firmware %s\n",
1250 filename);
1251 return ret;
1252 }
1253 }
1254 }
1255
1256 qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL);
1257 if (!qe_port) {
1258 dev_err(&ofdev->dev, "can't allocate QE port structure\n");
1259 return -ENOMEM;
1260 }
1261
1262 /* Search for IRQ and mapbase */
1263 ret = of_address_to_resource(np, 0, &res);
1264 if (ret) {
1265 dev_err(&ofdev->dev, "missing 'reg' property in device tree\n");
1266 goto out_free;
1267 }
1268 if (!res.start) {
1269 dev_err(&ofdev->dev, "invalid 'reg' property in device tree\n");
1270 ret = -EINVAL;
1271 goto out_free;
1272 }
1273 qe_port->port.mapbase = res.start;
1274
1275 /* Get the UCC number (device ID) */
1276 /* UCCs are numbered 1-7 */
1277 iprop = of_get_property(np, "cell-index", NULL);
1278 if (!iprop) {
1279 iprop = of_get_property(np, "device-id", NULL);
1280 if (!iprop) {
1281 dev_err(&ofdev->dev, "UCC is unspecified in "
1282 "device tree\n");
1283 ret = -EINVAL;
1284 goto out_free;
1285 }
1286 }
1287
1288 if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
1289 dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop);
1290 ret = -ENODEV;
1291 goto out_free;
1292 }
1293 qe_port->ucc_num = *iprop - 1;
1294
1295 /*
1296 * In the future, we should not require the BRG to be specified in the
1297 * device tree. If no clock-source is specified, then just pick a BRG
1298 * to use. This requires a new QE library function that manages BRG
1299 * assignments.
1300 */
1301
1302 sprop = of_get_property(np, "rx-clock-name", NULL);
1303 if (!sprop) {
1304 dev_err(&ofdev->dev, "missing rx-clock-name in device tree\n");
1305 ret = -ENODEV;
1306 goto out_free;
1307 }
1308
1309 qe_port->us_info.rx_clock = qe_clock_source(sprop);
1310 if ((qe_port->us_info.rx_clock < QE_BRG1) ||
1311 (qe_port->us_info.rx_clock > QE_BRG16)) {
1312 dev_err(&ofdev->dev, "rx-clock-name must be a BRG for UART\n");
1313 ret = -ENODEV;
1314 goto out_free;
1315 }
1316
1317#ifdef LOOPBACK
1318 /* In internal loopback mode, TX and RX must use the same clock */
1319 qe_port->us_info.tx_clock = qe_port->us_info.rx_clock;
1320#else
1321 sprop = of_get_property(np, "tx-clock-name", NULL);
1322 if (!sprop) {
1323 dev_err(&ofdev->dev, "missing tx-clock-name in device tree\n");
1324 ret = -ENODEV;
1325 goto out_free;
1326 }
1327 qe_port->us_info.tx_clock = qe_clock_source(sprop);
1328#endif
1329 if ((qe_port->us_info.tx_clock < QE_BRG1) ||
1330 (qe_port->us_info.tx_clock > QE_BRG16)) {
1331 dev_err(&ofdev->dev, "tx-clock-name must be a BRG for UART\n");
1332 ret = -ENODEV;
1333 goto out_free;
1334 }
1335
1336 /* Get the port number, numbered 0-3 */
1337 iprop = of_get_property(np, "port-number", NULL);
1338 if (!iprop) {
1339 dev_err(&ofdev->dev, "missing port-number in device tree\n");
1340 ret = -EINVAL;
1341 goto out_free;
1342 }
1343 qe_port->port.line = *iprop;
1344 if (qe_port->port.line >= UCC_MAX_UART) {
1345 dev_err(&ofdev->dev, "port-number must be 0-%u\n",
1346 UCC_MAX_UART - 1);
1347 ret = -EINVAL;
1348 goto out_free;
1349 }
1350
1351 qe_port->port.irq = irq_of_parse_and_map(np, 0);
1352 if (qe_port->port.irq == 0) {
1353 dev_err(&ofdev->dev, "could not map IRQ for UCC%u\n",
1354 qe_port->ucc_num + 1);
1355 ret = -EINVAL;
1356 goto out_free;
1357 }
1358
1359 /*
1360 * Newer device trees have an "fsl,qe" compatible property for the QE
1361 * node, but we still need to support older device trees.
1362 */
1363 np = of_find_compatible_node(NULL, NULL, "fsl,qe");
1364 if (!np) {
1365 np = of_find_node_by_type(NULL, "qe");
1366 if (!np) {
1367 dev_err(&ofdev->dev, "could not find 'qe' node\n");
1368 ret = -EINVAL;
1369 goto out_free;
1370 }
1371 }
1372
1373 iprop = of_get_property(np, "brg-frequency", NULL);
1374 if (!iprop) {
1375 dev_err(&ofdev->dev,
1376 "missing brg-frequency in device tree\n");
1377 ret = -EINVAL;
1378 goto out_np;
1379 }
1380
1381 if (*iprop)
1382 qe_port->port.uartclk = *iprop;
1383 else {
1384 /*
1385 * Older versions of U-Boot do not initialize the brg-frequency
1386 * property, so in this case we assume the BRG frequency is
1387 * half the QE bus frequency.
1388 */
1389 iprop = of_get_property(np, "bus-frequency", NULL);
1390 if (!iprop) {
1391 dev_err(&ofdev->dev,
1392 "missing QE bus-frequency in device tree\n");
1393 ret = -EINVAL;
1394 goto out_np;
1395 }
1396 if (*iprop)
1397 qe_port->port.uartclk = *iprop / 2;
1398 else {
1399 dev_err(&ofdev->dev,
1400 "invalid QE bus-frequency in device tree\n");
1401 ret = -EINVAL;
1402 goto out_np;
1403 }
1404 }
1405
1406 spin_lock_init(&qe_port->port.lock);
1407 qe_port->np = np;
1408 qe_port->port.dev = &ofdev->dev;
1409 qe_port->port.ops = &qe_uart_pops;
1410 qe_port->port.iotype = UPIO_MEM;
1411
1412 qe_port->tx_nrfifos = TX_NUM_FIFO;
1413 qe_port->tx_fifosize = TX_BUF_SIZE;
1414 qe_port->rx_nrfifos = RX_NUM_FIFO;
1415 qe_port->rx_fifosize = RX_BUF_SIZE;
1416
1417 qe_port->wait_closing = UCC_WAIT_CLOSING;
1418 qe_port->port.fifosize = 512;
1419 qe_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
1420
1421 qe_port->us_info.ucc_num = qe_port->ucc_num;
1422 qe_port->us_info.regs = (phys_addr_t) res.start;
1423 qe_port->us_info.irq = qe_port->port.irq;
1424
1425 qe_port->us_info.rx_bd_ring_len = qe_port->rx_nrfifos;
1426 qe_port->us_info.tx_bd_ring_len = qe_port->tx_nrfifos;
1427
1428 /* Make sure ucc_slow_init() initializes both TX and RX */
1429 qe_port->us_info.init_tx = 1;
1430 qe_port->us_info.init_rx = 1;
1431
1432 /* Add the port to the uart sub-system. This will cause
1433 * qe_uart_config_port() to be called, so the us_info structure must
1434 * be initialized.
1435 */
1436 ret = uart_add_one_port(&ucc_uart_driver, &qe_port->port);
1437 if (ret) {
1438 dev_err(&ofdev->dev, "could not add /dev/ttyQE%u\n",
1439 qe_port->port.line);
1440 goto out_np;
1441 }
1442
1443 platform_set_drvdata(ofdev, qe_port);
1444
1445 dev_info(&ofdev->dev, "UCC%u assigned to /dev/ttyQE%u\n",
1446 qe_port->ucc_num + 1, qe_port->port.line);
1447
1448 /* Display the mknod command for this device */
1449 dev_dbg(&ofdev->dev, "mknod command is 'mknod /dev/ttyQE%u c %u %u'\n",
1450 qe_port->port.line, SERIAL_QE_MAJOR,
1451 SERIAL_QE_MINOR + qe_port->port.line);
1452
1453 return 0;
1454out_np:
1455 of_node_put(np);
1456out_free:
1457 kfree(qe_port);
1458 return ret;
1459}
1460
1461static int ucc_uart_remove(struct platform_device *ofdev)
1462{
1463 struct uart_qe_port *qe_port = platform_get_drvdata(ofdev);
1464
1465 dev_info(&ofdev->dev, "removing /dev/ttyQE%u\n", qe_port->port.line);
1466
1467 uart_remove_one_port(&ucc_uart_driver, &qe_port->port);
1468
1469 kfree(qe_port);
1470
1471 return 0;
1472}
1473
1474static const struct of_device_id ucc_uart_match[] = {
1475 {
1476 .type = "serial",
1477 .compatible = "ucc_uart",
1478 },
1479 {
1480 .compatible = "fsl,t1040-ucc-uart",
1481 },
1482 {},
1483};
1484MODULE_DEVICE_TABLE(of, ucc_uart_match);
1485
1486static struct platform_driver ucc_uart_of_driver = {
1487 .driver = {
1488 .name = "ucc_uart",
1489 .of_match_table = ucc_uart_match,
1490 },
1491 .probe = ucc_uart_probe,
1492 .remove = ucc_uart_remove,
1493};
1494
1495static int __init ucc_uart_init(void)
1496{
1497 int ret;
1498
1499 printk(KERN_INFO "Freescale QUICC Engine UART device driver\n");
1500#ifdef LOOPBACK
1501 printk(KERN_INFO "ucc-uart: Using loopback mode\n");
1502#endif
1503
1504 ret = uart_register_driver(&ucc_uart_driver);
1505 if (ret) {
1506 printk(KERN_ERR "ucc-uart: could not register UART driver\n");
1507 return ret;
1508 }
1509
1510 ret = platform_driver_register(&ucc_uart_of_driver);
1511 if (ret) {
1512 printk(KERN_ERR
1513 "ucc-uart: could not register platform driver\n");
1514 uart_unregister_driver(&ucc_uart_driver);
1515 }
1516
1517 return ret;
1518}
1519
1520static void __exit ucc_uart_exit(void)
1521{
1522 printk(KERN_INFO
1523 "Freescale QUICC Engine UART device driver unloading\n");
1524
1525 platform_driver_unregister(&ucc_uart_of_driver);
1526 uart_unregister_driver(&ucc_uart_driver);
1527}
1528
1529module_init(ucc_uart_init);
1530module_exit(ucc_uart_exit);
1531
1532MODULE_DESCRIPTION("Freescale QUICC Engine (QE) UART");
1533MODULE_AUTHOR("Timur Tabi <timur@freescale.com>");
1534MODULE_LICENSE("GPL v2");
1535MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_QE_MAJOR);
1536
1/*
2 * Freescale QUICC Engine UART device driver
3 *
4 * Author: Timur Tabi <timur@freescale.com>
5 *
6 * Copyright 2007 Freescale Semiconductor, Inc. This file is licensed under
7 * the terms of the GNU General Public License version 2. This program
8 * is licensed "as is" without any warranty of any kind, whether express
9 * or implied.
10 *
11 * This driver adds support for UART devices via Freescale's QUICC Engine
12 * found on some Freescale SOCs.
13 *
14 * If Soft-UART support is needed but not already present, then this driver
15 * will request and upload the "Soft-UART" microcode upon probe. The
16 * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin, where "X"
17 * is the name of the SOC (e.g. 8323), and YZ is the revision of the SOC,
18 * (e.g. "11" for 1.1).
19 */
20
21#include <linux/module.h>
22#include <linux/serial.h>
23#include <linux/serial_core.h>
24#include <linux/slab.h>
25#include <linux/tty.h>
26#include <linux/tty_flip.h>
27#include <linux/io.h>
28#include <linux/of_address.h>
29#include <linux/of_irq.h>
30#include <linux/of_platform.h>
31#include <linux/dma-mapping.h>
32
33#include <linux/fs_uart_pd.h>
34#include <soc/fsl/qe/ucc_slow.h>
35
36#include <linux/firmware.h>
37#include <asm/reg.h>
38
39/*
40 * The GUMR flag for Soft UART. This would normally be defined in qe.h,
41 * but Soft-UART is a hack and we want to keep everything related to it in
42 * this file.
43 */
44#define UCC_SLOW_GUMR_H_SUART 0x00004000 /* Soft-UART */
45
46/*
47 * soft_uart is 1 if we need to use Soft-UART mode
48 */
49static int soft_uart;
50/*
51 * firmware_loaded is 1 if the firmware has been loaded, 0 otherwise.
52 */
53static int firmware_loaded;
54
55/* Enable this macro to configure all serial ports in internal loopback
56 mode */
57/* #define LOOPBACK */
58
59/* The major and minor device numbers are defined in
60 * http://www.lanana.org/docs/device-list/devices-2.6+.txt. For the QE
61 * UART, we have major number 204 and minor numbers 46 - 49, which are the
62 * same as for the CPM2. This decision was made because no Freescale part
63 * has both a CPM and a QE.
64 */
65#define SERIAL_QE_MAJOR 204
66#define SERIAL_QE_MINOR 46
67
68/* Since we only have minor numbers 46 - 49, there is a hard limit of 4 ports */
69#define UCC_MAX_UART 4
70
71/* The number of buffer descriptors for receiving characters. */
72#define RX_NUM_FIFO 4
73
74/* The number of buffer descriptors for transmitting characters. */
75#define TX_NUM_FIFO 4
76
77/* The maximum size of the character buffer for a single RX BD. */
78#define RX_BUF_SIZE 32
79
80/* The maximum size of the character buffer for a single TX BD. */
81#define TX_BUF_SIZE 32
82
83/*
84 * The number of jiffies to wait after receiving a close command before the
85 * device is actually closed. This allows the last few characters to be
86 * sent over the wire.
87 */
88#define UCC_WAIT_CLOSING 100
89
90struct ucc_uart_pram {
91 struct ucc_slow_pram common;
92 u8 res1[8]; /* reserved */
93 __be16 maxidl; /* Maximum idle chars */
94 __be16 idlc; /* temp idle counter */
95 __be16 brkcr; /* Break count register */
96 __be16 parec; /* receive parity error counter */
97 __be16 frmec; /* receive framing error counter */
98 __be16 nosec; /* receive noise counter */
99 __be16 brkec; /* receive break condition counter */
100 __be16 brkln; /* last received break length */
101 __be16 uaddr[2]; /* UART address character 1 & 2 */
102 __be16 rtemp; /* Temp storage */
103 __be16 toseq; /* Transmit out of sequence char */
104 __be16 cchars[8]; /* control characters 1-8 */
105 __be16 rccm; /* receive control character mask */
106 __be16 rccr; /* receive control character register */
107 __be16 rlbc; /* receive last break character */
108 __be16 res2; /* reserved */
109 __be32 res3; /* reserved, should be cleared */
110 u8 res4; /* reserved, should be cleared */
111 u8 res5[3]; /* reserved, should be cleared */
112 __be32 res6; /* reserved, should be cleared */
113 __be32 res7; /* reserved, should be cleared */
114 __be32 res8; /* reserved, should be cleared */
115 __be32 res9; /* reserved, should be cleared */
116 __be32 res10; /* reserved, should be cleared */
117 __be32 res11; /* reserved, should be cleared */
118 __be32 res12; /* reserved, should be cleared */
119 __be32 res13; /* reserved, should be cleared */
120/* The rest is for Soft-UART only */
121 __be16 supsmr; /* 0x90, Shadow UPSMR */
122 __be16 res92; /* 0x92, reserved, initialize to 0 */
123 __be32 rx_state; /* 0x94, RX state, initialize to 0 */
124 __be32 rx_cnt; /* 0x98, RX count, initialize to 0 */
125 u8 rx_length; /* 0x9C, Char length, set to 1+CL+PEN+1+SL */
126 u8 rx_bitmark; /* 0x9D, reserved, initialize to 0 */
127 u8 rx_temp_dlst_qe; /* 0x9E, reserved, initialize to 0 */
128 u8 res14[0xBC - 0x9F]; /* reserved */
129 __be32 dump_ptr; /* 0xBC, Dump pointer */
130 __be32 rx_frame_rem; /* 0xC0, reserved, initialize to 0 */
131 u8 rx_frame_rem_size; /* 0xC4, reserved, initialize to 0 */
132 u8 tx_mode; /* 0xC5, mode, 0=AHDLC, 1=UART */
133 __be16 tx_state; /* 0xC6, TX state */
134 u8 res15[0xD0 - 0xC8]; /* reserved */
135 __be32 resD0; /* 0xD0, reserved, initialize to 0 */
136 u8 resD4; /* 0xD4, reserved, initialize to 0 */
137 __be16 resD5; /* 0xD5, reserved, initialize to 0 */
138} __attribute__ ((packed));
139
140/* SUPSMR definitions, for Soft-UART only */
141#define UCC_UART_SUPSMR_SL 0x8000
142#define UCC_UART_SUPSMR_RPM_MASK 0x6000
143#define UCC_UART_SUPSMR_RPM_ODD 0x0000
144#define UCC_UART_SUPSMR_RPM_LOW 0x2000
145#define UCC_UART_SUPSMR_RPM_EVEN 0x4000
146#define UCC_UART_SUPSMR_RPM_HIGH 0x6000
147#define UCC_UART_SUPSMR_PEN 0x1000
148#define UCC_UART_SUPSMR_TPM_MASK 0x0C00
149#define UCC_UART_SUPSMR_TPM_ODD 0x0000
150#define UCC_UART_SUPSMR_TPM_LOW 0x0400
151#define UCC_UART_SUPSMR_TPM_EVEN 0x0800
152#define UCC_UART_SUPSMR_TPM_HIGH 0x0C00
153#define UCC_UART_SUPSMR_FRZ 0x0100
154#define UCC_UART_SUPSMR_UM_MASK 0x00c0
155#define UCC_UART_SUPSMR_UM_NORMAL 0x0000
156#define UCC_UART_SUPSMR_UM_MAN_MULTI 0x0040
157#define UCC_UART_SUPSMR_UM_AUTO_MULTI 0x00c0
158#define UCC_UART_SUPSMR_CL_MASK 0x0030
159#define UCC_UART_SUPSMR_CL_8 0x0030
160#define UCC_UART_SUPSMR_CL_7 0x0020
161#define UCC_UART_SUPSMR_CL_6 0x0010
162#define UCC_UART_SUPSMR_CL_5 0x0000
163
164#define UCC_UART_TX_STATE_AHDLC 0x00
165#define UCC_UART_TX_STATE_UART 0x01
166#define UCC_UART_TX_STATE_X1 0x00
167#define UCC_UART_TX_STATE_X16 0x80
168
169#define UCC_UART_PRAM_ALIGNMENT 0x100
170
171#define UCC_UART_SIZE_OF_BD UCC_SLOW_SIZE_OF_BD
172#define NUM_CONTROL_CHARS 8
173
174/* Private per-port data structure */
175struct uart_qe_port {
176 struct uart_port port;
177 struct ucc_slow __iomem *uccp;
178 struct ucc_uart_pram __iomem *uccup;
179 struct ucc_slow_info us_info;
180 struct ucc_slow_private *us_private;
181 struct device_node *np;
182 unsigned int ucc_num; /* First ucc is 0, not 1 */
183
184 u16 rx_nrfifos;
185 u16 rx_fifosize;
186 u16 tx_nrfifos;
187 u16 tx_fifosize;
188 int wait_closing;
189 u32 flags;
190 struct qe_bd *rx_bd_base;
191 struct qe_bd *rx_cur;
192 struct qe_bd *tx_bd_base;
193 struct qe_bd *tx_cur;
194 unsigned char *tx_buf;
195 unsigned char *rx_buf;
196 void *bd_virt; /* virtual address of the BD buffers */
197 dma_addr_t bd_dma_addr; /* bus address of the BD buffers */
198 unsigned int bd_size; /* size of BD buffer space */
199};
200
201static struct uart_driver ucc_uart_driver = {
202 .owner = THIS_MODULE,
203 .driver_name = "ucc_uart",
204 .dev_name = "ttyQE",
205 .major = SERIAL_QE_MAJOR,
206 .minor = SERIAL_QE_MINOR,
207 .nr = UCC_MAX_UART,
208};
209
210/*
211 * Virtual to physical address translation.
212 *
213 * Given the virtual address for a character buffer, this function returns
214 * the physical (DMA) equivalent.
215 */
216static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port)
217{
218 if (likely((addr >= qe_port->bd_virt)) &&
219 (addr < (qe_port->bd_virt + qe_port->bd_size)))
220 return qe_port->bd_dma_addr + (addr - qe_port->bd_virt);
221
222 /* something nasty happened */
223 printk(KERN_ERR "%s: addr=%p\n", __func__, addr);
224 BUG();
225 return 0;
226}
227
228/*
229 * Physical to virtual address translation.
230 *
231 * Given the physical (DMA) address for a character buffer, this function
232 * returns the virtual equivalent.
233 */
234static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port)
235{
236 /* sanity check */
237 if (likely((addr >= qe_port->bd_dma_addr) &&
238 (addr < (qe_port->bd_dma_addr + qe_port->bd_size))))
239 return qe_port->bd_virt + (addr - qe_port->bd_dma_addr);
240
241 /* something nasty happened */
242 printk(KERN_ERR "%s: addr=%llx\n", __func__, (u64)addr);
243 BUG();
244 return NULL;
245}
246
247/*
248 * Return 1 if the QE is done transmitting all buffers for this port
249 *
250 * This function scans each BD in sequence. If we find a BD that is not
251 * ready (READY=1), then we return 0 indicating that the QE is still sending
252 * data. If we reach the last BD (WRAP=1), then we know we've scanned
253 * the entire list, and all BDs are done.
254 */
255static unsigned int qe_uart_tx_empty(struct uart_port *port)
256{
257 struct uart_qe_port *qe_port =
258 container_of(port, struct uart_qe_port, port);
259 struct qe_bd *bdp = qe_port->tx_bd_base;
260
261 while (1) {
262 if (in_be16(&bdp->status) & BD_SC_READY)
263 /* This BD is not done, so return "not done" */
264 return 0;
265
266 if (in_be16(&bdp->status) & BD_SC_WRAP)
267 /*
268 * This BD is done and it's the last one, so return
269 * "done"
270 */
271 return 1;
272
273 bdp++;
274 }
275}
276
277/*
278 * Set the modem control lines
279 *
280 * Although the QE can control the modem control lines (e.g. CTS), we
281 * don't need that support. This function must exist, however, otherwise
282 * the kernel will panic.
283 */
284void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
285{
286}
287
288/*
289 * Get the current modem control line status
290 *
291 * Although the QE can control the modem control lines (e.g. CTS), this
292 * driver currently doesn't support that, so we always return Carrier
293 * Detect, Data Set Ready, and Clear To Send.
294 */
295static unsigned int qe_uart_get_mctrl(struct uart_port *port)
296{
297 return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
298}
299
300/*
301 * Disable the transmit interrupt.
302 *
303 * Although this function is called "stop_tx", it does not actually stop
304 * transmission of data. Instead, it tells the QE to not generate an
305 * interrupt when the UCC is finished sending characters.
306 */
307static void qe_uart_stop_tx(struct uart_port *port)
308{
309 struct uart_qe_port *qe_port =
310 container_of(port, struct uart_qe_port, port);
311
312 clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
313}
314
315/*
316 * Transmit as many characters to the HW as possible.
317 *
318 * This function will attempt to stuff of all the characters from the
319 * kernel's transmit buffer into TX BDs.
320 *
321 * A return value of non-zero indicates that it successfully stuffed all
322 * characters from the kernel buffer.
323 *
324 * A return value of zero indicates that there are still characters in the
325 * kernel's buffer that have not been transmitted, but there are no more BDs
326 * available. This function should be called again after a BD has been made
327 * available.
328 */
329static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
330{
331 struct qe_bd *bdp;
332 unsigned char *p;
333 unsigned int count;
334 struct uart_port *port = &qe_port->port;
335 struct circ_buf *xmit = &port->state->xmit;
336
337 bdp = qe_port->rx_cur;
338
339 /* Handle xon/xoff */
340 if (port->x_char) {
341 /* Pick next descriptor and fill from buffer */
342 bdp = qe_port->tx_cur;
343
344 p = qe2cpu_addr(bdp->buf, qe_port);
345
346 *p++ = port->x_char;
347 out_be16(&bdp->length, 1);
348 setbits16(&bdp->status, BD_SC_READY);
349 /* Get next BD. */
350 if (in_be16(&bdp->status) & BD_SC_WRAP)
351 bdp = qe_port->tx_bd_base;
352 else
353 bdp++;
354 qe_port->tx_cur = bdp;
355
356 port->icount.tx++;
357 port->x_char = 0;
358 return 1;
359 }
360
361 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
362 qe_uart_stop_tx(port);
363 return 0;
364 }
365
366 /* Pick next descriptor and fill from buffer */
367 bdp = qe_port->tx_cur;
368
369 while (!(in_be16(&bdp->status) & BD_SC_READY) &&
370 (xmit->tail != xmit->head)) {
371 count = 0;
372 p = qe2cpu_addr(bdp->buf, qe_port);
373 while (count < qe_port->tx_fifosize) {
374 *p++ = xmit->buf[xmit->tail];
375 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
376 port->icount.tx++;
377 count++;
378 if (xmit->head == xmit->tail)
379 break;
380 }
381
382 out_be16(&bdp->length, count);
383 setbits16(&bdp->status, BD_SC_READY);
384
385 /* Get next BD. */
386 if (in_be16(&bdp->status) & BD_SC_WRAP)
387 bdp = qe_port->tx_bd_base;
388 else
389 bdp++;
390 }
391 qe_port->tx_cur = bdp;
392
393 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
394 uart_write_wakeup(port);
395
396 if (uart_circ_empty(xmit)) {
397 /* The kernel buffer is empty, so turn off TX interrupts. We
398 don't need to be told when the QE is finished transmitting
399 the data. */
400 qe_uart_stop_tx(port);
401 return 0;
402 }
403
404 return 1;
405}
406
407/*
408 * Start transmitting data
409 *
410 * This function will start transmitting any available data, if the port
411 * isn't already transmitting data.
412 */
413static void qe_uart_start_tx(struct uart_port *port)
414{
415 struct uart_qe_port *qe_port =
416 container_of(port, struct uart_qe_port, port);
417
418 /* If we currently are transmitting, then just return */
419 if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
420 return;
421
422 /* Otherwise, pump the port and start transmission */
423 if (qe_uart_tx_pump(qe_port))
424 setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
425}
426
427/*
428 * Stop transmitting data
429 */
430static void qe_uart_stop_rx(struct uart_port *port)
431{
432 struct uart_qe_port *qe_port =
433 container_of(port, struct uart_qe_port, port);
434
435 clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
436}
437
438/* Start or stop sending break signal
439 *
440 * This function controls the sending of a break signal. If break_state=1,
441 * then we start sending a break signal. If break_state=0, then we stop
442 * sending the break signal.
443 */
444static void qe_uart_break_ctl(struct uart_port *port, int break_state)
445{
446 struct uart_qe_port *qe_port =
447 container_of(port, struct uart_qe_port, port);
448
449 if (break_state)
450 ucc_slow_stop_tx(qe_port->us_private);
451 else
452 ucc_slow_restart_tx(qe_port->us_private);
453}
454
455/* ISR helper function for receiving character.
456 *
457 * This function is called by the ISR to handling receiving characters
458 */
459static void qe_uart_int_rx(struct uart_qe_port *qe_port)
460{
461 int i;
462 unsigned char ch, *cp;
463 struct uart_port *port = &qe_port->port;
464 struct tty_port *tport = &port->state->port;
465 struct qe_bd *bdp;
466 u16 status;
467 unsigned int flg;
468
469 /* Just loop through the closed BDs and copy the characters into
470 * the buffer.
471 */
472 bdp = qe_port->rx_cur;
473 while (1) {
474 status = in_be16(&bdp->status);
475
476 /* If this one is empty, then we assume we've read them all */
477 if (status & BD_SC_EMPTY)
478 break;
479
480 /* get number of characters, and check space in RX buffer */
481 i = in_be16(&bdp->length);
482
483 /* If we don't have enough room in RX buffer for the entire BD,
484 * then we try later, which will be the next RX interrupt.
485 */
486 if (tty_buffer_request_room(tport, i) < i) {
487 dev_dbg(port->dev, "ucc-uart: no room in RX buffer\n");
488 return;
489 }
490
491 /* get pointer */
492 cp = qe2cpu_addr(bdp->buf, qe_port);
493
494 /* loop through the buffer */
495 while (i-- > 0) {
496 ch = *cp++;
497 port->icount.rx++;
498 flg = TTY_NORMAL;
499
500 if (!i && status &
501 (BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV))
502 goto handle_error;
503 if (uart_handle_sysrq_char(port, ch))
504 continue;
505
506error_return:
507 tty_insert_flip_char(tport, ch, flg);
508
509 }
510
511 /* This BD is ready to be used again. Clear status. get next */
512 clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR |
513 BD_SC_OV | BD_SC_ID, BD_SC_EMPTY);
514 if (in_be16(&bdp->status) & BD_SC_WRAP)
515 bdp = qe_port->rx_bd_base;
516 else
517 bdp++;
518
519 }
520
521 /* Write back buffer pointer */
522 qe_port->rx_cur = bdp;
523
524 /* Activate BH processing */
525 tty_flip_buffer_push(tport);
526
527 return;
528
529 /* Error processing */
530
531handle_error:
532 /* Statistics */
533 if (status & BD_SC_BR)
534 port->icount.brk++;
535 if (status & BD_SC_PR)
536 port->icount.parity++;
537 if (status & BD_SC_FR)
538 port->icount.frame++;
539 if (status & BD_SC_OV)
540 port->icount.overrun++;
541
542 /* Mask out ignored conditions */
543 status &= port->read_status_mask;
544
545 /* Handle the remaining ones */
546 if (status & BD_SC_BR)
547 flg = TTY_BREAK;
548 else if (status & BD_SC_PR)
549 flg = TTY_PARITY;
550 else if (status & BD_SC_FR)
551 flg = TTY_FRAME;
552
553 /* Overrun does not affect the current character ! */
554 if (status & BD_SC_OV)
555 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
556#ifdef SUPPORT_SYSRQ
557 port->sysrq = 0;
558#endif
559 goto error_return;
560}
561
562/* Interrupt handler
563 *
564 * This interrupt handler is called after a BD is processed.
565 */
566static irqreturn_t qe_uart_int(int irq, void *data)
567{
568 struct uart_qe_port *qe_port = (struct uart_qe_port *) data;
569 struct ucc_slow __iomem *uccp = qe_port->uccp;
570 u16 events;
571
572 /* Clear the interrupts */
573 events = in_be16(&uccp->ucce);
574 out_be16(&uccp->ucce, events);
575
576 if (events & UCC_UART_UCCE_BRKE)
577 uart_handle_break(&qe_port->port);
578
579 if (events & UCC_UART_UCCE_RX)
580 qe_uart_int_rx(qe_port);
581
582 if (events & UCC_UART_UCCE_TX)
583 qe_uart_tx_pump(qe_port);
584
585 return events ? IRQ_HANDLED : IRQ_NONE;
586}
587
588/* Initialize buffer descriptors
589 *
590 * This function initializes all of the RX and TX buffer descriptors.
591 */
592static void qe_uart_initbd(struct uart_qe_port *qe_port)
593{
594 int i;
595 void *bd_virt;
596 struct qe_bd *bdp;
597
598 /* Set the physical address of the host memory buffers in the buffer
599 * descriptors, and the virtual address for us to work with.
600 */
601 bd_virt = qe_port->bd_virt;
602 bdp = qe_port->rx_bd_base;
603 qe_port->rx_cur = qe_port->rx_bd_base;
604 for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) {
605 out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT);
606 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
607 out_be16(&bdp->length, 0);
608 bd_virt += qe_port->rx_fifosize;
609 bdp++;
610 }
611
612 /* */
613 out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT);
614 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
615 out_be16(&bdp->length, 0);
616
617 /* Set the physical address of the host memory
618 * buffers in the buffer descriptors, and the
619 * virtual address for us to work with.
620 */
621 bd_virt = qe_port->bd_virt +
622 L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
623 qe_port->tx_cur = qe_port->tx_bd_base;
624 bdp = qe_port->tx_bd_base;
625 for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) {
626 out_be16(&bdp->status, BD_SC_INTRPT);
627 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
628 out_be16(&bdp->length, 0);
629 bd_virt += qe_port->tx_fifosize;
630 bdp++;
631 }
632
633 /* Loopback requires the preamble bit to be set on the first TX BD */
634#ifdef LOOPBACK
635 setbits16(&qe_port->tx_cur->status, BD_SC_P);
636#endif
637
638 out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT);
639 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
640 out_be16(&bdp->length, 0);
641}
642
643/*
644 * Initialize a UCC for UART.
645 *
646 * This function configures a given UCC to be used as a UART device. Basic
647 * UCC initialization is handled in qe_uart_request_port(). This function
648 * does all the UART-specific stuff.
649 */
650static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
651{
652 u32 cecr_subblock;
653 struct ucc_slow __iomem *uccp = qe_port->uccp;
654 struct ucc_uart_pram *uccup = qe_port->uccup;
655
656 unsigned int i;
657
658 /* First, disable TX and RX in the UCC */
659 ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
660
661 /* Program the UCC UART parameter RAM */
662 out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
663 out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
664 out_be16(&uccup->common.mrblr, qe_port->rx_fifosize);
665 out_be16(&uccup->maxidl, 0x10);
666 out_be16(&uccup->brkcr, 1);
667 out_be16(&uccup->parec, 0);
668 out_be16(&uccup->frmec, 0);
669 out_be16(&uccup->nosec, 0);
670 out_be16(&uccup->brkec, 0);
671 out_be16(&uccup->uaddr[0], 0);
672 out_be16(&uccup->uaddr[1], 0);
673 out_be16(&uccup->toseq, 0);
674 for (i = 0; i < 8; i++)
675 out_be16(&uccup->cchars[i], 0xC000);
676 out_be16(&uccup->rccm, 0xc0ff);
677
678 /* Configure the GUMR registers for UART */
679 if (soft_uart) {
680 /* Soft-UART requires a 1X multiplier for TX */
681 clrsetbits_be32(&uccp->gumr_l,
682 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
683 UCC_SLOW_GUMR_L_RDCR_MASK,
684 UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 |
685 UCC_SLOW_GUMR_L_RDCR_16);
686
687 clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
688 UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
689 } else {
690 clrsetbits_be32(&uccp->gumr_l,
691 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
692 UCC_SLOW_GUMR_L_RDCR_MASK,
693 UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 |
694 UCC_SLOW_GUMR_L_RDCR_16);
695
696 clrsetbits_be32(&uccp->gumr_h,
697 UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
698 UCC_SLOW_GUMR_H_RFW);
699 }
700
701#ifdef LOOPBACK
702 clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
703 UCC_SLOW_GUMR_L_DIAG_LOOP);
704 clrsetbits_be32(&uccp->gumr_h,
705 UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
706 UCC_SLOW_GUMR_H_CDS);
707#endif
708
709 /* Disable rx interrupts and clear all pending events. */
710 out_be16(&uccp->uccm, 0);
711 out_be16(&uccp->ucce, 0xffff);
712 out_be16(&uccp->udsr, 0x7e7e);
713
714 /* Initialize UPSMR */
715 out_be16(&uccp->upsmr, 0);
716
717 if (soft_uart) {
718 out_be16(&uccup->supsmr, 0x30);
719 out_be16(&uccup->res92, 0);
720 out_be32(&uccup->rx_state, 0);
721 out_be32(&uccup->rx_cnt, 0);
722 out_8(&uccup->rx_bitmark, 0);
723 out_8(&uccup->rx_length, 10);
724 out_be32(&uccup->dump_ptr, 0x4000);
725 out_8(&uccup->rx_temp_dlst_qe, 0);
726 out_be32(&uccup->rx_frame_rem, 0);
727 out_8(&uccup->rx_frame_rem_size, 0);
728 /* Soft-UART requires TX to be 1X */
729 out_8(&uccup->tx_mode,
730 UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1);
731 out_be16(&uccup->tx_state, 0);
732 out_8(&uccup->resD4, 0);
733 out_be16(&uccup->resD5, 0);
734
735 /* Set UART mode.
736 * Enable receive and transmit.
737 */
738
739 /* From the microcode errata:
740 * 1.GUMR_L register, set mode=0010 (QMC).
741 * 2.Set GUMR_H[17] bit. (UART/AHDLC mode).
742 * 3.Set GUMR_H[19:20] (Transparent mode)
743 * 4.Clear GUMR_H[26] (RFW)
744 * ...
745 * 6.Receiver must use 16x over sampling
746 */
747 clrsetbits_be32(&uccp->gumr_l,
748 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
749 UCC_SLOW_GUMR_L_RDCR_MASK,
750 UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 |
751 UCC_SLOW_GUMR_L_RDCR_16);
752
753 clrsetbits_be32(&uccp->gumr_h,
754 UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
755 UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX |
756 UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
757
758#ifdef LOOPBACK
759 clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
760 UCC_SLOW_GUMR_L_DIAG_LOOP);
761 clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP |
762 UCC_SLOW_GUMR_H_CDS);
763#endif
764
765 cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
766 qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
767 QE_CR_PROTOCOL_UNSPECIFIED, 0);
768 } else {
769 cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
770 qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
771 QE_CR_PROTOCOL_UART, 0);
772 }
773}
774
775/*
776 * Initialize the port.
777 */
778static int qe_uart_startup(struct uart_port *port)
779{
780 struct uart_qe_port *qe_port =
781 container_of(port, struct uart_qe_port, port);
782 int ret;
783
784 /*
785 * If we're using Soft-UART mode, then we need to make sure the
786 * firmware has been uploaded first.
787 */
788 if (soft_uart && !firmware_loaded) {
789 dev_err(port->dev, "Soft-UART firmware not uploaded\n");
790 return -ENODEV;
791 }
792
793 qe_uart_initbd(qe_port);
794 qe_uart_init_ucc(qe_port);
795
796 /* Install interrupt handler. */
797 ret = request_irq(port->irq, qe_uart_int, IRQF_SHARED, "ucc-uart",
798 qe_port);
799 if (ret) {
800 dev_err(port->dev, "could not claim IRQ %u\n", port->irq);
801 return ret;
802 }
803
804 /* Startup rx-int */
805 setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
806 ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX);
807
808 return 0;
809}
810
811/*
812 * Shutdown the port.
813 */
814static void qe_uart_shutdown(struct uart_port *port)
815{
816 struct uart_qe_port *qe_port =
817 container_of(port, struct uart_qe_port, port);
818 struct ucc_slow __iomem *uccp = qe_port->uccp;
819 unsigned int timeout = 20;
820
821 /* Disable RX and TX */
822
823 /* Wait for all the BDs marked sent */
824 while (!qe_uart_tx_empty(port)) {
825 if (!--timeout) {
826 dev_warn(port->dev, "shutdown timeout\n");
827 break;
828 }
829 set_current_state(TASK_UNINTERRUPTIBLE);
830 schedule_timeout(2);
831 }
832
833 if (qe_port->wait_closing) {
834 /* Wait a bit longer */
835 set_current_state(TASK_UNINTERRUPTIBLE);
836 schedule_timeout(qe_port->wait_closing);
837 }
838
839 /* Stop uarts */
840 ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
841 clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
842
843 /* Shut them really down and reinit buffer descriptors */
844 ucc_slow_graceful_stop_tx(qe_port->us_private);
845 qe_uart_initbd(qe_port);
846
847 free_irq(port->irq, qe_port);
848}
849
850/*
851 * Set the serial port parameters.
852 */
853static void qe_uart_set_termios(struct uart_port *port,
854 struct ktermios *termios, struct ktermios *old)
855{
856 struct uart_qe_port *qe_port =
857 container_of(port, struct uart_qe_port, port);
858 struct ucc_slow __iomem *uccp = qe_port->uccp;
859 unsigned int baud;
860 unsigned long flags;
861 u16 upsmr = in_be16(&uccp->upsmr);
862 struct ucc_uart_pram __iomem *uccup = qe_port->uccup;
863 u16 supsmr = in_be16(&uccup->supsmr);
864 u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */
865
866 /* Character length programmed into the mode register is the
867 * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
868 * 1 or 2 stop bits, minus 1.
869 * The value 'bits' counts this for us.
870 */
871
872 /* byte size */
873 upsmr &= UCC_UART_UPSMR_CL_MASK;
874 supsmr &= UCC_UART_SUPSMR_CL_MASK;
875
876 switch (termios->c_cflag & CSIZE) {
877 case CS5:
878 upsmr |= UCC_UART_UPSMR_CL_5;
879 supsmr |= UCC_UART_SUPSMR_CL_5;
880 char_length += 5;
881 break;
882 case CS6:
883 upsmr |= UCC_UART_UPSMR_CL_6;
884 supsmr |= UCC_UART_SUPSMR_CL_6;
885 char_length += 6;
886 break;
887 case CS7:
888 upsmr |= UCC_UART_UPSMR_CL_7;
889 supsmr |= UCC_UART_SUPSMR_CL_7;
890 char_length += 7;
891 break;
892 default: /* case CS8 */
893 upsmr |= UCC_UART_UPSMR_CL_8;
894 supsmr |= UCC_UART_SUPSMR_CL_8;
895 char_length += 8;
896 break;
897 }
898
899 /* If CSTOPB is set, we want two stop bits */
900 if (termios->c_cflag & CSTOPB) {
901 upsmr |= UCC_UART_UPSMR_SL;
902 supsmr |= UCC_UART_SUPSMR_SL;
903 char_length++; /* + SL */
904 }
905
906 if (termios->c_cflag & PARENB) {
907 upsmr |= UCC_UART_UPSMR_PEN;
908 supsmr |= UCC_UART_SUPSMR_PEN;
909 char_length++; /* + PEN */
910
911 if (!(termios->c_cflag & PARODD)) {
912 upsmr &= ~(UCC_UART_UPSMR_RPM_MASK |
913 UCC_UART_UPSMR_TPM_MASK);
914 upsmr |= UCC_UART_UPSMR_RPM_EVEN |
915 UCC_UART_UPSMR_TPM_EVEN;
916 supsmr &= ~(UCC_UART_SUPSMR_RPM_MASK |
917 UCC_UART_SUPSMR_TPM_MASK);
918 supsmr |= UCC_UART_SUPSMR_RPM_EVEN |
919 UCC_UART_SUPSMR_TPM_EVEN;
920 }
921 }
922
923 /*
924 * Set up parity check flag
925 */
926 port->read_status_mask = BD_SC_EMPTY | BD_SC_OV;
927 if (termios->c_iflag & INPCK)
928 port->read_status_mask |= BD_SC_FR | BD_SC_PR;
929 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
930 port->read_status_mask |= BD_SC_BR;
931
932 /*
933 * Characters to ignore
934 */
935 port->ignore_status_mask = 0;
936 if (termios->c_iflag & IGNPAR)
937 port->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
938 if (termios->c_iflag & IGNBRK) {
939 port->ignore_status_mask |= BD_SC_BR;
940 /*
941 * If we're ignore parity and break indicators, ignore
942 * overruns too. (For real raw support).
943 */
944 if (termios->c_iflag & IGNPAR)
945 port->ignore_status_mask |= BD_SC_OV;
946 }
947 /*
948 * !!! ignore all characters if CREAD is not set
949 */
950 if ((termios->c_cflag & CREAD) == 0)
951 port->read_status_mask &= ~BD_SC_EMPTY;
952
953 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
954
955 /* Do we really need a spinlock here? */
956 spin_lock_irqsave(&port->lock, flags);
957
958 /* Update the per-port timeout. */
959 uart_update_timeout(port, termios->c_cflag, baud);
960
961 out_be16(&uccp->upsmr, upsmr);
962 if (soft_uart) {
963 out_be16(&uccup->supsmr, supsmr);
964 out_8(&uccup->rx_length, char_length);
965
966 /* Soft-UART requires a 1X multiplier for TX */
967 qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
968 qe_setbrg(qe_port->us_info.tx_clock, baud, 1);
969 } else {
970 qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
971 qe_setbrg(qe_port->us_info.tx_clock, baud, 16);
972 }
973
974 spin_unlock_irqrestore(&port->lock, flags);
975}
976
977/*
978 * Return a pointer to a string that describes what kind of port this is.
979 */
980static const char *qe_uart_type(struct uart_port *port)
981{
982 return "QE";
983}
984
985/*
986 * Allocate any memory and I/O resources required by the port.
987 */
988static int qe_uart_request_port(struct uart_port *port)
989{
990 int ret;
991 struct uart_qe_port *qe_port =
992 container_of(port, struct uart_qe_port, port);
993 struct ucc_slow_info *us_info = &qe_port->us_info;
994 struct ucc_slow_private *uccs;
995 unsigned int rx_size, tx_size;
996 void *bd_virt;
997 dma_addr_t bd_dma_addr = 0;
998
999 ret = ucc_slow_init(us_info, &uccs);
1000 if (ret) {
1001 dev_err(port->dev, "could not initialize UCC%u\n",
1002 qe_port->ucc_num);
1003 return ret;
1004 }
1005
1006 qe_port->us_private = uccs;
1007 qe_port->uccp = uccs->us_regs;
1008 qe_port->uccup = (struct ucc_uart_pram *) uccs->us_pram;
1009 qe_port->rx_bd_base = uccs->rx_bd;
1010 qe_port->tx_bd_base = uccs->tx_bd;
1011
1012 /*
1013 * Allocate the transmit and receive data buffers.
1014 */
1015
1016 rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
1017 tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize);
1018
1019 bd_virt = dma_alloc_coherent(port->dev, rx_size + tx_size, &bd_dma_addr,
1020 GFP_KERNEL);
1021 if (!bd_virt) {
1022 dev_err(port->dev, "could not allocate buffer descriptors\n");
1023 return -ENOMEM;
1024 }
1025
1026 qe_port->bd_virt = bd_virt;
1027 qe_port->bd_dma_addr = bd_dma_addr;
1028 qe_port->bd_size = rx_size + tx_size;
1029
1030 qe_port->rx_buf = bd_virt;
1031 qe_port->tx_buf = qe_port->rx_buf + rx_size;
1032
1033 return 0;
1034}
1035
1036/*
1037 * Configure the port.
1038 *
1039 * We say we're a CPM-type port because that's mostly true. Once the device
1040 * is configured, this driver operates almost identically to the CPM serial
1041 * driver.
1042 */
1043static void qe_uart_config_port(struct uart_port *port, int flags)
1044{
1045 if (flags & UART_CONFIG_TYPE) {
1046 port->type = PORT_CPM;
1047 qe_uart_request_port(port);
1048 }
1049}
1050
1051/*
1052 * Release any memory and I/O resources that were allocated in
1053 * qe_uart_request_port().
1054 */
1055static void qe_uart_release_port(struct uart_port *port)
1056{
1057 struct uart_qe_port *qe_port =
1058 container_of(port, struct uart_qe_port, port);
1059 struct ucc_slow_private *uccs = qe_port->us_private;
1060
1061 dma_free_coherent(port->dev, qe_port->bd_size, qe_port->bd_virt,
1062 qe_port->bd_dma_addr);
1063
1064 ucc_slow_free(uccs);
1065}
1066
1067/*
1068 * Verify that the data in serial_struct is suitable for this device.
1069 */
1070static int qe_uart_verify_port(struct uart_port *port,
1071 struct serial_struct *ser)
1072{
1073 if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM)
1074 return -EINVAL;
1075
1076 if (ser->irq < 0 || ser->irq >= nr_irqs)
1077 return -EINVAL;
1078
1079 if (ser->baud_base < 9600)
1080 return -EINVAL;
1081
1082 return 0;
1083}
1084/* UART operations
1085 *
1086 * Details on these functions can be found in Documentation/serial/driver
1087 */
1088static struct uart_ops qe_uart_pops = {
1089 .tx_empty = qe_uart_tx_empty,
1090 .set_mctrl = qe_uart_set_mctrl,
1091 .get_mctrl = qe_uart_get_mctrl,
1092 .stop_tx = qe_uart_stop_tx,
1093 .start_tx = qe_uart_start_tx,
1094 .stop_rx = qe_uart_stop_rx,
1095 .break_ctl = qe_uart_break_ctl,
1096 .startup = qe_uart_startup,
1097 .shutdown = qe_uart_shutdown,
1098 .set_termios = qe_uart_set_termios,
1099 .type = qe_uart_type,
1100 .release_port = qe_uart_release_port,
1101 .request_port = qe_uart_request_port,
1102 .config_port = qe_uart_config_port,
1103 .verify_port = qe_uart_verify_port,
1104};
1105
1106/*
1107 * Obtain the SOC model number and revision level
1108 *
1109 * This function parses the device tree to obtain the SOC model. It then
1110 * reads the SVR register to the revision.
1111 *
1112 * The device tree stores the SOC model two different ways.
1113 *
1114 * The new way is:
1115 *
1116 * cpu@0 {
1117 * compatible = "PowerPC,8323";
1118 * device_type = "cpu";
1119 * ...
1120 *
1121 *
1122 * The old way is:
1123 * PowerPC,8323@0 {
1124 * device_type = "cpu";
1125 * ...
1126 *
1127 * This code first checks the new way, and then the old way.
1128 */
1129static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l)
1130{
1131 struct device_node *np;
1132 const char *soc_string;
1133 unsigned int svr;
1134 unsigned int soc;
1135
1136 /* Find the CPU node */
1137 np = of_find_node_by_type(NULL, "cpu");
1138 if (!np)
1139 return 0;
1140 /* Find the compatible property */
1141 soc_string = of_get_property(np, "compatible", NULL);
1142 if (!soc_string)
1143 /* No compatible property, so try the name. */
1144 soc_string = np->name;
1145
1146 /* Extract the SOC number from the "PowerPC," string */
1147 if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc)
1148 return 0;
1149
1150 /* Get the revision from the SVR */
1151 svr = mfspr(SPRN_SVR);
1152 *rev_h = (svr >> 4) & 0xf;
1153 *rev_l = svr & 0xf;
1154
1155 return soc;
1156}
1157
1158/*
1159 * requst_firmware_nowait() callback function
1160 *
1161 * This function is called by the kernel when a firmware is made available,
1162 * or if it times out waiting for the firmware.
1163 */
1164static void uart_firmware_cont(const struct firmware *fw, void *context)
1165{
1166 struct qe_firmware *firmware;
1167 struct device *dev = context;
1168 int ret;
1169
1170 if (!fw) {
1171 dev_err(dev, "firmware not found\n");
1172 return;
1173 }
1174
1175 firmware = (struct qe_firmware *) fw->data;
1176
1177 if (firmware->header.length != fw->size) {
1178 dev_err(dev, "invalid firmware\n");
1179 goto out;
1180 }
1181
1182 ret = qe_upload_firmware(firmware);
1183 if (ret) {
1184 dev_err(dev, "could not load firmware\n");
1185 goto out;
1186 }
1187
1188 firmware_loaded = 1;
1189 out:
1190 release_firmware(fw);
1191}
1192
1193static int ucc_uart_probe(struct platform_device *ofdev)
1194{
1195 struct device_node *np = ofdev->dev.of_node;
1196 const unsigned int *iprop; /* Integer OF properties */
1197 const char *sprop; /* String OF properties */
1198 struct uart_qe_port *qe_port = NULL;
1199 struct resource res;
1200 int ret;
1201
1202 /*
1203 * Determine if we need Soft-UART mode
1204 */
1205 if (of_find_property(np, "soft-uart", NULL)) {
1206 dev_dbg(&ofdev->dev, "using Soft-UART mode\n");
1207 soft_uart = 1;
1208 }
1209
1210 /*
1211 * If we are using Soft-UART, determine if we need to upload the
1212 * firmware, too.
1213 */
1214 if (soft_uart) {
1215 struct qe_firmware_info *qe_fw_info;
1216
1217 qe_fw_info = qe_get_firmware_info();
1218
1219 /* Check if the firmware has been uploaded. */
1220 if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
1221 firmware_loaded = 1;
1222 } else {
1223 char filename[32];
1224 unsigned int soc;
1225 unsigned int rev_h;
1226 unsigned int rev_l;
1227
1228 soc = soc_info(&rev_h, &rev_l);
1229 if (!soc) {
1230 dev_err(&ofdev->dev, "unknown CPU model\n");
1231 return -ENXIO;
1232 }
1233 sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
1234 soc, rev_h, rev_l);
1235
1236 dev_info(&ofdev->dev, "waiting for firmware %s\n",
1237 filename);
1238
1239 /*
1240 * We call request_firmware_nowait instead of
1241 * request_firmware so that the driver can load and
1242 * initialize the ports without holding up the rest of
1243 * the kernel. If hotplug support is enabled in the
1244 * kernel, then we use it.
1245 */
1246 ret = request_firmware_nowait(THIS_MODULE,
1247 FW_ACTION_HOTPLUG, filename, &ofdev->dev,
1248 GFP_KERNEL, &ofdev->dev, uart_firmware_cont);
1249 if (ret) {
1250 dev_err(&ofdev->dev,
1251 "could not load firmware %s\n",
1252 filename);
1253 return ret;
1254 }
1255 }
1256 }
1257
1258 qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL);
1259 if (!qe_port) {
1260 dev_err(&ofdev->dev, "can't allocate QE port structure\n");
1261 return -ENOMEM;
1262 }
1263
1264 /* Search for IRQ and mapbase */
1265 ret = of_address_to_resource(np, 0, &res);
1266 if (ret) {
1267 dev_err(&ofdev->dev, "missing 'reg' property in device tree\n");
1268 goto out_free;
1269 }
1270 if (!res.start) {
1271 dev_err(&ofdev->dev, "invalid 'reg' property in device tree\n");
1272 ret = -EINVAL;
1273 goto out_free;
1274 }
1275 qe_port->port.mapbase = res.start;
1276
1277 /* Get the UCC number (device ID) */
1278 /* UCCs are numbered 1-7 */
1279 iprop = of_get_property(np, "cell-index", NULL);
1280 if (!iprop) {
1281 iprop = of_get_property(np, "device-id", NULL);
1282 if (!iprop) {
1283 dev_err(&ofdev->dev, "UCC is unspecified in "
1284 "device tree\n");
1285 ret = -EINVAL;
1286 goto out_free;
1287 }
1288 }
1289
1290 if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
1291 dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop);
1292 ret = -ENODEV;
1293 goto out_free;
1294 }
1295 qe_port->ucc_num = *iprop - 1;
1296
1297 /*
1298 * In the future, we should not require the BRG to be specified in the
1299 * device tree. If no clock-source is specified, then just pick a BRG
1300 * to use. This requires a new QE library function that manages BRG
1301 * assignments.
1302 */
1303
1304 sprop = of_get_property(np, "rx-clock-name", NULL);
1305 if (!sprop) {
1306 dev_err(&ofdev->dev, "missing rx-clock-name in device tree\n");
1307 ret = -ENODEV;
1308 goto out_free;
1309 }
1310
1311 qe_port->us_info.rx_clock = qe_clock_source(sprop);
1312 if ((qe_port->us_info.rx_clock < QE_BRG1) ||
1313 (qe_port->us_info.rx_clock > QE_BRG16)) {
1314 dev_err(&ofdev->dev, "rx-clock-name must be a BRG for UART\n");
1315 ret = -ENODEV;
1316 goto out_free;
1317 }
1318
1319#ifdef LOOPBACK
1320 /* In internal loopback mode, TX and RX must use the same clock */
1321 qe_port->us_info.tx_clock = qe_port->us_info.rx_clock;
1322#else
1323 sprop = of_get_property(np, "tx-clock-name", NULL);
1324 if (!sprop) {
1325 dev_err(&ofdev->dev, "missing tx-clock-name in device tree\n");
1326 ret = -ENODEV;
1327 goto out_free;
1328 }
1329 qe_port->us_info.tx_clock = qe_clock_source(sprop);
1330#endif
1331 if ((qe_port->us_info.tx_clock < QE_BRG1) ||
1332 (qe_port->us_info.tx_clock > QE_BRG16)) {
1333 dev_err(&ofdev->dev, "tx-clock-name must be a BRG for UART\n");
1334 ret = -ENODEV;
1335 goto out_free;
1336 }
1337
1338 /* Get the port number, numbered 0-3 */
1339 iprop = of_get_property(np, "port-number", NULL);
1340 if (!iprop) {
1341 dev_err(&ofdev->dev, "missing port-number in device tree\n");
1342 ret = -EINVAL;
1343 goto out_free;
1344 }
1345 qe_port->port.line = *iprop;
1346 if (qe_port->port.line >= UCC_MAX_UART) {
1347 dev_err(&ofdev->dev, "port-number must be 0-%u\n",
1348 UCC_MAX_UART - 1);
1349 ret = -EINVAL;
1350 goto out_free;
1351 }
1352
1353 qe_port->port.irq = irq_of_parse_and_map(np, 0);
1354 if (qe_port->port.irq == 0) {
1355 dev_err(&ofdev->dev, "could not map IRQ for UCC%u\n",
1356 qe_port->ucc_num + 1);
1357 ret = -EINVAL;
1358 goto out_free;
1359 }
1360
1361 /*
1362 * Newer device trees have an "fsl,qe" compatible property for the QE
1363 * node, but we still need to support older device trees.
1364 */
1365 np = of_find_compatible_node(NULL, NULL, "fsl,qe");
1366 if (!np) {
1367 np = of_find_node_by_type(NULL, "qe");
1368 if (!np) {
1369 dev_err(&ofdev->dev, "could not find 'qe' node\n");
1370 ret = -EINVAL;
1371 goto out_free;
1372 }
1373 }
1374
1375 iprop = of_get_property(np, "brg-frequency", NULL);
1376 if (!iprop) {
1377 dev_err(&ofdev->dev,
1378 "missing brg-frequency in device tree\n");
1379 ret = -EINVAL;
1380 goto out_np;
1381 }
1382
1383 if (*iprop)
1384 qe_port->port.uartclk = *iprop;
1385 else {
1386 /*
1387 * Older versions of U-Boot do not initialize the brg-frequency
1388 * property, so in this case we assume the BRG frequency is
1389 * half the QE bus frequency.
1390 */
1391 iprop = of_get_property(np, "bus-frequency", NULL);
1392 if (!iprop) {
1393 dev_err(&ofdev->dev,
1394 "missing QE bus-frequency in device tree\n");
1395 ret = -EINVAL;
1396 goto out_np;
1397 }
1398 if (*iprop)
1399 qe_port->port.uartclk = *iprop / 2;
1400 else {
1401 dev_err(&ofdev->dev,
1402 "invalid QE bus-frequency in device tree\n");
1403 ret = -EINVAL;
1404 goto out_np;
1405 }
1406 }
1407
1408 spin_lock_init(&qe_port->port.lock);
1409 qe_port->np = np;
1410 qe_port->port.dev = &ofdev->dev;
1411 qe_port->port.ops = &qe_uart_pops;
1412 qe_port->port.iotype = UPIO_MEM;
1413
1414 qe_port->tx_nrfifos = TX_NUM_FIFO;
1415 qe_port->tx_fifosize = TX_BUF_SIZE;
1416 qe_port->rx_nrfifos = RX_NUM_FIFO;
1417 qe_port->rx_fifosize = RX_BUF_SIZE;
1418
1419 qe_port->wait_closing = UCC_WAIT_CLOSING;
1420 qe_port->port.fifosize = 512;
1421 qe_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
1422
1423 qe_port->us_info.ucc_num = qe_port->ucc_num;
1424 qe_port->us_info.regs = (phys_addr_t) res.start;
1425 qe_port->us_info.irq = qe_port->port.irq;
1426
1427 qe_port->us_info.rx_bd_ring_len = qe_port->rx_nrfifos;
1428 qe_port->us_info.tx_bd_ring_len = qe_port->tx_nrfifos;
1429
1430 /* Make sure ucc_slow_init() initializes both TX and RX */
1431 qe_port->us_info.init_tx = 1;
1432 qe_port->us_info.init_rx = 1;
1433
1434 /* Add the port to the uart sub-system. This will cause
1435 * qe_uart_config_port() to be called, so the us_info structure must
1436 * be initialized.
1437 */
1438 ret = uart_add_one_port(&ucc_uart_driver, &qe_port->port);
1439 if (ret) {
1440 dev_err(&ofdev->dev, "could not add /dev/ttyQE%u\n",
1441 qe_port->port.line);
1442 goto out_np;
1443 }
1444
1445 platform_set_drvdata(ofdev, qe_port);
1446
1447 dev_info(&ofdev->dev, "UCC%u assigned to /dev/ttyQE%u\n",
1448 qe_port->ucc_num + 1, qe_port->port.line);
1449
1450 /* Display the mknod command for this device */
1451 dev_dbg(&ofdev->dev, "mknod command is 'mknod /dev/ttyQE%u c %u %u'\n",
1452 qe_port->port.line, SERIAL_QE_MAJOR,
1453 SERIAL_QE_MINOR + qe_port->port.line);
1454
1455 return 0;
1456out_np:
1457 of_node_put(np);
1458out_free:
1459 kfree(qe_port);
1460 return ret;
1461}
1462
1463static int ucc_uart_remove(struct platform_device *ofdev)
1464{
1465 struct uart_qe_port *qe_port = platform_get_drvdata(ofdev);
1466
1467 dev_info(&ofdev->dev, "removing /dev/ttyQE%u\n", qe_port->port.line);
1468
1469 uart_remove_one_port(&ucc_uart_driver, &qe_port->port);
1470
1471 kfree(qe_port);
1472
1473 return 0;
1474}
1475
1476static const struct of_device_id ucc_uart_match[] = {
1477 {
1478 .type = "serial",
1479 .compatible = "ucc_uart",
1480 },
1481 {},
1482};
1483MODULE_DEVICE_TABLE(of, ucc_uart_match);
1484
1485static struct platform_driver ucc_uart_of_driver = {
1486 .driver = {
1487 .name = "ucc_uart",
1488 .of_match_table = ucc_uart_match,
1489 },
1490 .probe = ucc_uart_probe,
1491 .remove = ucc_uart_remove,
1492};
1493
1494static int __init ucc_uart_init(void)
1495{
1496 int ret;
1497
1498 printk(KERN_INFO "Freescale QUICC Engine UART device driver\n");
1499#ifdef LOOPBACK
1500 printk(KERN_INFO "ucc-uart: Using loopback mode\n");
1501#endif
1502
1503 ret = uart_register_driver(&ucc_uart_driver);
1504 if (ret) {
1505 printk(KERN_ERR "ucc-uart: could not register UART driver\n");
1506 return ret;
1507 }
1508
1509 ret = platform_driver_register(&ucc_uart_of_driver);
1510 if (ret) {
1511 printk(KERN_ERR
1512 "ucc-uart: could not register platform driver\n");
1513 uart_unregister_driver(&ucc_uart_driver);
1514 }
1515
1516 return ret;
1517}
1518
1519static void __exit ucc_uart_exit(void)
1520{
1521 printk(KERN_INFO
1522 "Freescale QUICC Engine UART device driver unloading\n");
1523
1524 platform_driver_unregister(&ucc_uart_of_driver);
1525 uart_unregister_driver(&ucc_uart_driver);
1526}
1527
1528module_init(ucc_uart_init);
1529module_exit(ucc_uart_exit);
1530
1531MODULE_DESCRIPTION("Freescale QUICC Engine (QE) UART");
1532MODULE_AUTHOR("Timur Tabi <timur@freescale.com>");
1533MODULE_LICENSE("GPL v2");
1534MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_QE_MAJOR);
1535