Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10/*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 * 2: CN22
15 * 3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 * amixer set "LINEOUT Mixer DACL" on
20 * amixer set "DVC Out" 100%
21 * amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 * amixer set "DVC Out Mute" on
26 * amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
31 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 * amixer set "DVC Out Ramp" on
33 * aplay xxx.wav &
34 * amixer set "DVC Out" 80% // Volume Down
35 * amixer set "DVC Out" 100% // Volume Up
36 */
37
38/dts-v1/;
39#include "r8a7790.dtsi"
40#include <dt-bindings/gpio/gpio.h>
41#include <dt-bindings/input/input.h>
42
43/ {
44 model = "Lager";
45 compatible = "renesas,lager", "renesas,r8a7790";
46
47 aliases {
48 serial0 = &scif0;
49 serial1 = &scifa1;
50 i2c8 = &gpioi2c1;
51 i2c9 = &gpioi2c2;
52 i2c10 = &i2cexio0;
53 i2c11 = &i2cexio1;
54 i2c12 = &i2chdmi;
55 i2c13 = &i2cpwr;
56 };
57
58 chosen {
59 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
60 stdout-path = "serial0:115200n8";
61 };
62
63 memory@40000000 {
64 device_type = "memory";
65 reg = <0 0x40000000 0 0x40000000>;
66 };
67
68 memory@140000000 {
69 device_type = "memory";
70 reg = <1 0x40000000 0 0xc0000000>;
71 };
72
73 lbsc {
74 #address-cells = <1>;
75 #size-cells = <1>;
76 };
77
78 keyboard {
79 compatible = "gpio-keys";
80
81 one {
82 linux,code = <KEY_1>;
83 label = "SW2-1";
84 wakeup-source;
85 debounce-interval = <20>;
86 gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
87 };
88 two {
89 linux,code = <KEY_2>;
90 label = "SW2-2";
91 wakeup-source;
92 debounce-interval = <20>;
93 gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
94 };
95 three {
96 linux,code = <KEY_3>;
97 label = "SW2-3";
98 wakeup-source;
99 debounce-interval = <20>;
100 gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
101 };
102 four {
103 linux,code = <KEY_4>;
104 label = "SW2-4";
105 wakeup-source;
106 debounce-interval = <20>;
107 gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
108 };
109 };
110
111 leds {
112 compatible = "gpio-leds";
113 led6 {
114 gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
115 };
116 led7 {
117 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
118 };
119 led8 {
120 gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
121 };
122 };
123
124 fixedregulator3v3: regulator-3v3 {
125 compatible = "regulator-fixed";
126 regulator-name = "fixed-3.3V";
127 regulator-min-microvolt = <3300000>;
128 regulator-max-microvolt = <3300000>;
129 regulator-boot-on;
130 regulator-always-on;
131 };
132
133 vcc_sdhi0: regulator-vcc-sdhi0 {
134 compatible = "regulator-fixed";
135
136 regulator-name = "SDHI0 Vcc";
137 regulator-min-microvolt = <3300000>;
138 regulator-max-microvolt = <3300000>;
139
140 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
141 enable-active-high;
142 };
143
144 vccq_sdhi0: regulator-vccq-sdhi0 {
145 compatible = "regulator-gpio";
146
147 regulator-name = "SDHI0 VccQ";
148 regulator-min-microvolt = <1800000>;
149 regulator-max-microvolt = <3300000>;
150
151 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
152 gpios-states = <1>;
153 states = <3300000 1
154 1800000 0>;
155 };
156
157 vcc_sdhi2: regulator-vcc-sdhi2 {
158 compatible = "regulator-fixed";
159
160 regulator-name = "SDHI2 Vcc";
161 regulator-min-microvolt = <3300000>;
162 regulator-max-microvolt = <3300000>;
163
164 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
165 enable-active-high;
166 };
167
168 vccq_sdhi2: regulator-vccq-sdhi2 {
169 compatible = "regulator-gpio";
170
171 regulator-name = "SDHI2 VccQ";
172 regulator-min-microvolt = <1800000>;
173 regulator-max-microvolt = <3300000>;
174
175 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
176 gpios-states = <1>;
177 states = <3300000 1
178 1800000 0>;
179 };
180
181 audio_clock: audio_clock {
182 compatible = "fixed-clock";
183 #clock-cells = <0>;
184 clock-frequency = <11289600>;
185 };
186
187 rsnd_ak4643: sound {
188 compatible = "simple-audio-card";
189
190 simple-audio-card,format = "left_j";
191 simple-audio-card,bitclock-master = <&sndcodec>;
192 simple-audio-card,frame-master = <&sndcodec>;
193
194 sndcpu: simple-audio-card,cpu {
195 sound-dai = <&rcar_sound>;
196 };
197
198 sndcodec: simple-audio-card,codec {
199 sound-dai = <&ak4643>;
200 clocks = <&audio_clock>;
201 };
202 };
203
204 vga-encoder {
205 compatible = "adi,adv7123";
206
207 ports {
208 #address-cells = <1>;
209 #size-cells = <0>;
210
211 port@0 {
212 reg = <0>;
213 adv7123_in: endpoint {
214 remote-endpoint = <&du_out_rgb>;
215 };
216 };
217 port@1 {
218 reg = <1>;
219 adv7123_out: endpoint {
220 remote-endpoint = <&vga_in>;
221 };
222 };
223 };
224 };
225
226 vga {
227 compatible = "vga-connector";
228
229 port {
230 vga_in: endpoint {
231 remote-endpoint = <&adv7123_out>;
232 };
233 };
234 };
235
236 hdmi-in {
237 compatible = "hdmi-connector";
238 type = "a";
239
240 port {
241 hdmi_con_in: endpoint {
242 remote-endpoint = <&adv7612_in>;
243 };
244 };
245 };
246
247 cec_clock: cec-clock {
248 compatible = "fixed-clock";
249 #clock-cells = <0>;
250 clock-frequency = <12000000>;
251 };
252
253 hdmi-out {
254 compatible = "hdmi-connector";
255 type = "a";
256
257 port {
258 hdmi_con_out: endpoint {
259 remote-endpoint = <&adv7511_out>;
260 };
261 };
262 };
263
264 x2_clk: x2-clock {
265 compatible = "fixed-clock";
266 #clock-cells = <0>;
267 clock-frequency = <148500000>;
268 };
269
270 x13_clk: x13-clock {
271 compatible = "fixed-clock";
272 #clock-cells = <0>;
273 clock-frequency = <148500000>;
274 };
275
276 gpioi2c1: i2c-8 {
277 #address-cells = <1>;
278 #size-cells = <0>;
279 compatible = "i2c-gpio";
280 status = "disabled";
281 scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
282 sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
283 i2c-gpio,delay-us = <5>;
284 };
285
286 gpioi2c2: i2c-9 {
287 #address-cells = <1>;
288 #size-cells = <0>;
289 compatible = "i2c-gpio";
290 status = "disabled";
291 scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
292 sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
293 i2c-gpio,delay-us = <5>;
294 };
295
296 /*
297 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
298 * We use the I2C demuxer, so the desired IP core can be selected at runtime
299 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
300 * Note: For testing the I2C slave feature, it is convenient to connect this
301 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
302 * instantiate the slave device at runtime according to the documentation.
303 * You can then communicate with the slave via IIC3.
304 *
305 * IIC0/I2C0 does not appear to support fallback to GPIO.
306 */
307 i2cexio0: i2c-10 {
308 compatible = "i2c-demux-pinctrl";
309 i2c-parent = <&iic0>, <&i2c0>;
310 i2c-bus-name = "i2c-exio0";
311 #address-cells = <1>;
312 #size-cells = <0>;
313 };
314
315 /*
316 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
317 * This is similar to the arangement described for i2cexio0 (above)
318 * with a fallback to GPIO also provided.
319 */
320 i2cexio1: i2c-11 {
321 compatible = "i2c-demux-pinctrl";
322 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
323 i2c-bus-name = "i2c-exio1";
324 #address-cells = <1>;
325 #size-cells = <0>;
326 };
327
328 /*
329 * IIC2 and I2C2 may be switched using pinmux.
330 * A fallback to GPIO is also provided.
331 */
332 i2chdmi: i2c-12 {
333 compatible = "i2c-demux-pinctrl";
334 i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
335 i2c-bus-name = "i2c-hdmi";
336 #address-cells = <1>;
337 #size-cells = <0>;
338
339 ak4643: codec@12 {
340 compatible = "asahi-kasei,ak4643";
341 #sound-dai-cells = <0>;
342 reg = <0x12>;
343 };
344
345 composite-in@20 {
346 compatible = "adi,adv7180";
347 reg = <0x20>;
348 remote = <&vin1>;
349
350 port {
351 adv7180: endpoint {
352 bus-width = <8>;
353 remote-endpoint = <&vin1ep0>;
354 };
355 };
356 };
357
358 hdmi@39 {
359 compatible = "adi,adv7511w";
360 reg = <0x39>;
361 interrupt-parent = <&gpio1>;
362 interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
363 clocks = <&cec_clock>;
364 clock-names = "cec";
365
366 adi,input-depth = <8>;
367 adi,input-colorspace = "rgb";
368 adi,input-clock = "1x";
369 adi,input-style = <1>;
370 adi,input-justification = "evenly";
371
372 ports {
373 #address-cells = <1>;
374 #size-cells = <0>;
375
376 port@0 {
377 reg = <0>;
378 adv7511_in: endpoint {
379 remote-endpoint = <&lvds0_out>;
380 };
381 };
382
383 port@1 {
384 reg = <1>;
385 adv7511_out: endpoint {
386 remote-endpoint = <&hdmi_con_out>;
387 };
388 };
389 };
390 };
391
392 hdmi-in@4c {
393 compatible = "adi,adv7612";
394 reg = <0x4c>;
395 interrupt-parent = <&gpio1>;
396 interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
397 default-input = <0>;
398
399 ports {
400 #address-cells = <1>;
401 #size-cells = <0>;
402
403 port@0 {
404 reg = <0>;
405 adv7612_in: endpoint {
406 remote-endpoint = <&hdmi_con_in>;
407 };
408 };
409
410 port@2 {
411 reg = <2>;
412 adv7612_out: endpoint {
413 remote-endpoint = <&vin0ep2>;
414 };
415 };
416 };
417 };
418 };
419
420 /*
421 * IIC3 and I2C3 may be switched using pinmux.
422 * IIC3/I2C3 does not appear to support fallback to GPIO.
423 */
424 i2cpwr: i2c-13 {
425 compatible = "i2c-demux-pinctrl";
426 pinctrl-names = "default";
427 pinctrl-0 = <&pmic_irq_pins>;
428 i2c-parent = <&iic3>, <&i2c3>;
429 i2c-bus-name = "i2c-pwr";
430 #address-cells = <1>;
431 #size-cells = <0>;
432
433 pmic@58 {
434 compatible = "dlg,da9063";
435 reg = <0x58>;
436 interrupt-parent = <&irqc0>;
437 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
438 interrupt-controller;
439
440 rtc {
441 compatible = "dlg,da9063-rtc";
442 };
443
444 wdt {
445 compatible = "dlg,da9063-watchdog";
446 };
447 };
448
449 vdd_dvfs: regulator@68 {
450 compatible = "dlg,da9210";
451 reg = <0x68>;
452 interrupt-parent = <&irqc0>;
453 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
454
455 regulator-min-microvolt = <1000000>;
456 regulator-max-microvolt = <1000000>;
457 regulator-boot-on;
458 regulator-always-on;
459 };
460 };
461};
462
463&du {
464 pinctrl-0 = <&du_pins>;
465 pinctrl-names = "default";
466 status = "okay";
467
468 clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
469 <&x13_clk>, <&x2_clk>;
470 clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
471
472 ports {
473 port@0 {
474 endpoint {
475 remote-endpoint = <&adv7123_in>;
476 };
477 };
478 };
479};
480
481&lvds0 {
482 status = "okay";
483
484 ports {
485 port@1 {
486 endpoint {
487 remote-endpoint = <&adv7511_in>;
488 };
489 };
490 };
491};
492
493&lvds1 {
494 ports {
495 port@1 {
496 lvds_connector: endpoint {
497 };
498 };
499 };
500};
501
502&extal_clk {
503 clock-frequency = <20000000>;
504};
505
506&pfc {
507 pinctrl-0 = <&scif_clk_pins>;
508 pinctrl-names = "default";
509
510 du_pins: du {
511 groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
512 function = "du";
513 };
514
515 scif0_pins: scif0 {
516 groups = "scif0_data";
517 function = "scif0";
518 };
519
520 scif_clk_pins: scif_clk {
521 groups = "scif_clk";
522 function = "scif_clk";
523 };
524
525 ether_pins: ether {
526 groups = "eth_link", "eth_mdio", "eth_rmii";
527 function = "eth";
528 };
529
530 phy1_pins: phy1 {
531 groups = "intc_irq0";
532 function = "intc";
533 };
534
535 scifa1_pins: scifa1 {
536 groups = "scifa1_data";
537 function = "scifa1";
538 };
539
540 sdhi0_pins: sd0 {
541 groups = "sdhi0_data4", "sdhi0_ctrl";
542 function = "sdhi0";
543 power-source = <3300>;
544 };
545
546 sdhi0_pins_uhs: sd0_uhs {
547 groups = "sdhi0_data4", "sdhi0_ctrl";
548 function = "sdhi0";
549 power-source = <1800>;
550 };
551
552 sdhi2_pins: sd2 {
553 groups = "sdhi2_data4", "sdhi2_ctrl";
554 function = "sdhi2";
555 power-source = <3300>;
556 };
557
558 sdhi2_pins_uhs: sd2_uhs {
559 groups = "sdhi2_data4", "sdhi2_ctrl";
560 function = "sdhi2";
561 power-source = <1800>;
562 };
563
564 mmc1_pins: mmc1 {
565 groups = "mmc1_data8", "mmc1_ctrl";
566 function = "mmc1";
567 };
568
569 qspi_pins: qspi {
570 groups = "qspi_ctrl", "qspi_data4";
571 function = "qspi";
572 };
573
574 msiof1_pins: msiof1 {
575 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
576 "msiof1_tx";
577 function = "msiof1";
578 };
579
580 i2c0_pins: i2c0 {
581 groups = "i2c0";
582 function = "i2c0";
583 };
584
585 iic0_pins: iic0 {
586 groups = "iic0";
587 function = "iic0";
588 };
589
590 i2c1_pins: i2c1 {
591 groups = "i2c1";
592 function = "i2c1";
593 };
594
595 iic1_pins: iic1 {
596 groups = "iic1";
597 function = "iic1";
598 };
599
600 i2c2_pins: i2c2 {
601 groups = "i2c2";
602 function = "i2c2";
603 };
604
605 iic2_pins: iic2 {
606 groups = "iic2";
607 function = "iic2";
608 };
609
610 i2c3_pins: i2c3 {
611 groups = "i2c3";
612 function = "i2c3";
613 };
614
615 iic3_pins: iic3 {
616 groups = "iic3";
617 function = "iic3";
618 };
619
620 pmic_irq_pins: pmicirq {
621 groups = "intc_irq2";
622 function = "intc";
623 };
624
625 hsusb_pins: hsusb {
626 groups = "usb0_ovc_vbus";
627 function = "usb0";
628 };
629
630 usb0_pins: usb0 {
631 groups = "usb0";
632 function = "usb0";
633 };
634
635 usb1_pins: usb1 {
636 groups = "usb1";
637 function = "usb1";
638 };
639
640 usb2_pins: usb2 {
641 groups = "usb2";
642 function = "usb2";
643 };
644
645 vin0_pins: vin0 {
646 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
647 function = "vin0";
648 };
649
650 vin1_pins: vin1 {
651 groups = "vin1_data8", "vin1_clk";
652 function = "vin1";
653 };
654
655 sound_pins: sound {
656 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
657 function = "ssi";
658 };
659
660 sound_clk_pins: sound_clk {
661 groups = "audio_clk_a";
662 function = "audio_clk";
663 };
664};
665
666ðer {
667 pinctrl-0 = <ðer_pins &phy1_pins>;
668 pinctrl-names = "default";
669
670 phy-handle = <&phy1>;
671 renesas,ether-link-active-low;
672 status = "okay";
673
674 phy1: ethernet-phy@1 {
675 reg = <1>;
676 interrupt-parent = <&irqc0>;
677 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
678 micrel,led-mode = <1>;
679 };
680};
681
682&cmt0 {
683 status = "okay";
684};
685
686&mmcif1 {
687 pinctrl-0 = <&mmc1_pins>;
688 pinctrl-names = "default";
689
690 vmmc-supply = <&fixedregulator3v3>;
691 bus-width = <8>;
692 non-removable;
693 status = "okay";
694};
695
696&sata1 {
697 status = "okay";
698};
699
700&qspi {
701 pinctrl-0 = <&qspi_pins>;
702 pinctrl-names = "default";
703
704 status = "okay";
705
706 flash: flash@0 {
707 compatible = "spansion,s25fl512s", "jedec,spi-nor";
708 reg = <0>;
709 spi-max-frequency = <30000000>;
710 spi-tx-bus-width = <4>;
711 spi-rx-bus-width = <4>;
712 spi-cpha;
713 spi-cpol;
714 m25p,fast-read;
715
716 partitions {
717 compatible = "fixed-partitions";
718 #address-cells = <1>;
719 #size-cells = <1>;
720
721 partition@0 {
722 label = "loader";
723 reg = <0x00000000 0x00040000>;
724 read-only;
725 };
726 partition@40000 {
727 label = "user";
728 reg = <0x00040000 0x00400000>;
729 read-only;
730 };
731 partition@440000 {
732 label = "flash";
733 reg = <0x00440000 0x03bc0000>;
734 };
735 };
736 };
737};
738
739&scif0 {
740 pinctrl-0 = <&scif0_pins>;
741 pinctrl-names = "default";
742
743 status = "okay";
744};
745
746&scifa1 {
747 pinctrl-0 = <&scifa1_pins>;
748 pinctrl-names = "default";
749
750 status = "okay";
751};
752
753&scif_clk {
754 clock-frequency = <14745600>;
755};
756
757&msiof1 {
758 pinctrl-0 = <&msiof1_pins>;
759 pinctrl-names = "default";
760
761 status = "okay";
762
763 pmic: pmic@0 {
764 compatible = "renesas,r2a11302ft";
765 reg = <0>;
766 spi-max-frequency = <6000000>;
767 spi-cpol;
768 spi-cpha;
769 };
770};
771
772&sdhi0 {
773 pinctrl-0 = <&sdhi0_pins>;
774 pinctrl-1 = <&sdhi0_pins_uhs>;
775 pinctrl-names = "default", "state_uhs";
776
777 vmmc-supply = <&vcc_sdhi0>;
778 vqmmc-supply = <&vccq_sdhi0>;
779 cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
780 sd-uhs-sdr50;
781 sd-uhs-sdr104;
782 status = "okay";
783};
784
785&sdhi2 {
786 pinctrl-0 = <&sdhi2_pins>;
787 pinctrl-1 = <&sdhi2_pins_uhs>;
788 pinctrl-names = "default", "state_uhs";
789
790 vmmc-supply = <&vcc_sdhi2>;
791 vqmmc-supply = <&vccq_sdhi2>;
792 cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
793 sd-uhs-sdr50;
794 status = "okay";
795};
796
797&cpu0 {
798 cpu0-supply = <&vdd_dvfs>;
799};
800
801&i2c0 {
802 pinctrl-0 = <&i2c0_pins>;
803 pinctrl-names = "i2c-exio0";
804};
805
806&iic0 {
807 pinctrl-0 = <&iic0_pins>;
808 pinctrl-names = "i2c-exio0";
809};
810
811&i2c1 {
812 pinctrl-0 = <&i2c1_pins>;
813 pinctrl-names = "i2c-exio1";
814};
815
816&iic1 {
817 pinctrl-0 = <&iic1_pins>;
818 pinctrl-names = "i2c-exio1";
819};
820
821&i2c2 {
822 pinctrl-0 = <&i2c2_pins>;
823 pinctrl-names = "i2c-hdmi";
824
825 clock-frequency = <100000>;
826};
827
828&iic2 {
829 pinctrl-0 = <&iic2_pins>;
830 pinctrl-names = "i2c-hdmi";
831
832 clock-frequency = <100000>;
833};
834
835&i2c3 {
836 pinctrl-0 = <&i2c3_pins>;
837 pinctrl-names = "i2c-pwr";
838};
839
840&iic3 {
841 pinctrl-0 = <&iic3_pins>;
842 pinctrl-names = "i2c-pwr";
843};
844
845&pci0 {
846 status = "okay";
847 pinctrl-0 = <&usb0_pins>;
848 pinctrl-names = "default";
849};
850
851&pci1 {
852 status = "okay";
853 pinctrl-0 = <&usb1_pins>;
854 pinctrl-names = "default";
855};
856
857&xhci {
858 status = "okay";
859 pinctrl-0 = <&usb2_pins>;
860 pinctrl-names = "default";
861};
862
863&pci2 {
864 status = "okay";
865 pinctrl-0 = <&usb2_pins>;
866 pinctrl-names = "default";
867};
868
869&hsusb {
870 status = "okay";
871 pinctrl-0 = <&hsusb_pins>;
872 pinctrl-names = "default";
873 renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
874};
875
876&usbphy {
877 status = "okay";
878};
879
880/* HDMI video input */
881&vin0 {
882 pinctrl-0 = <&vin0_pins>;
883 pinctrl-names = "default";
884
885 status = "okay";
886
887 port {
888 vin0ep2: endpoint {
889 remote-endpoint = <&adv7612_out>;
890 bus-width = <24>;
891 hsync-active = <0>;
892 vsync-active = <0>;
893 pclk-sample = <1>;
894 data-active = <1>;
895 };
896 };
897};
898
899/* composite video input */
900&vin1 {
901 pinctrl-0 = <&vin1_pins>;
902 pinctrl-names = "default";
903
904 status = "okay";
905
906 port {
907 vin1ep0: endpoint {
908 remote-endpoint = <&adv7180>;
909 bus-width = <8>;
910 };
911 };
912};
913
914&rcar_sound {
915 pinctrl-0 = <&sound_pins &sound_clk_pins>;
916 pinctrl-names = "default";
917
918 /* Single DAI */
919 #sound-dai-cells = <0>;
920
921 status = "okay";
922
923 rcar_sound,dai {
924 dai0 {
925 playback = <&ssi0 &src2 &dvc0>;
926 capture = <&ssi1 &src3 &dvc1>;
927 };
928 };
929};
930
931&rwdt {
932 timeout-sec = <60>;
933 status = "okay";
934};
935
936&ssi1 {
937 shared-pin;
938};
1/*
2 * Device Tree Source for the Lager board
3 *
4 * Copyright (C) 2013-2014 Renesas Solutions Corp.
5 * Copyright (C) 2014 Cogent Embedded, Inc.
6 * Copyright (C) 2015-2016 Renesas Electronics Corporation
7 *
8 * This file is licensed under the terms of the GNU General Public License
9 * version 2. This program is licensed "as is" without any warranty of any
10 * kind, whether express or implied.
11 */
12
13/*
14 * SSI-AK4643
15 *
16 * SW1: 1: AK4643
17 * 2: CN22
18 * 3: ADV7511
19 *
20 * This command is required when Playback/Capture
21 *
22 * amixer set "LINEOUT Mixer DACL" on
23 * amixer set "DVC Out" 100%
24 * amixer set "DVC In" 100%
25 *
26 * You can use Mute
27 *
28 * amixer set "DVC Out Mute" on
29 * amixer set "DVC In Mute" on
30 *
31 * You can use Volume Ramp
32 *
33 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
34 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
35 * amixer set "DVC Out Ramp" on
36 * aplay xxx.wav &
37 * amixer set "DVC Out" 80% // Volume Down
38 * amixer set "DVC Out" 100% // Volume Up
39 */
40
41/dts-v1/;
42#include "r8a7790.dtsi"
43#include <dt-bindings/gpio/gpio.h>
44#include <dt-bindings/input/input.h>
45
46/ {
47 model = "Lager";
48 compatible = "renesas,lager", "renesas,r8a7790";
49
50 aliases {
51 serial0 = &scif0;
52 serial1 = &scifa1;
53 i2c8 = "i2cexio";
54 };
55
56 chosen {
57 bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
58 stdout-path = "serial0:115200n8";
59 };
60
61 memory@40000000 {
62 device_type = "memory";
63 reg = <0 0x40000000 0 0x40000000>;
64 };
65
66 memory@140000000 {
67 device_type = "memory";
68 reg = <1 0x40000000 0 0xc0000000>;
69 };
70
71 lbsc {
72 #address-cells = <1>;
73 #size-cells = <1>;
74 };
75
76 keyboard {
77 compatible = "gpio-keys";
78
79 button@1 {
80 linux,code = <KEY_1>;
81 label = "SW2-1";
82 wakeup-source;
83 debounce-interval = <20>;
84 gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
85 };
86 button@2 {
87 linux,code = <KEY_2>;
88 label = "SW2-2";
89 wakeup-source;
90 debounce-interval = <20>;
91 gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
92 };
93 button@3 {
94 linux,code = <KEY_3>;
95 label = "SW2-3";
96 wakeup-source;
97 debounce-interval = <20>;
98 gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
99 };
100 button@4 {
101 linux,code = <KEY_4>;
102 label = "SW2-4";
103 wakeup-source;
104 debounce-interval = <20>;
105 gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
106 };
107 };
108
109 leds {
110 compatible = "gpio-leds";
111 led6 {
112 gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
113 };
114 led7 {
115 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
116 };
117 led8 {
118 gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
119 };
120 };
121
122 fixedregulator3v3: fixedregulator@0 {
123 compatible = "regulator-fixed";
124 regulator-name = "fixed-3.3V";
125 regulator-min-microvolt = <3300000>;
126 regulator-max-microvolt = <3300000>;
127 regulator-boot-on;
128 regulator-always-on;
129 };
130
131 vcc_sdhi0: regulator@1 {
132 compatible = "regulator-fixed";
133
134 regulator-name = "SDHI0 Vcc";
135 regulator-min-microvolt = <3300000>;
136 regulator-max-microvolt = <3300000>;
137
138 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
139 enable-active-high;
140 };
141
142 vccq_sdhi0: regulator@2 {
143 compatible = "regulator-gpio";
144
145 regulator-name = "SDHI0 VccQ";
146 regulator-min-microvolt = <1800000>;
147 regulator-max-microvolt = <3300000>;
148
149 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
150 gpios-states = <1>;
151 states = <3300000 1
152 1800000 0>;
153 };
154
155 vcc_sdhi2: regulator@3 {
156 compatible = "regulator-fixed";
157
158 regulator-name = "SDHI2 Vcc";
159 regulator-min-microvolt = <3300000>;
160 regulator-max-microvolt = <3300000>;
161
162 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
163 enable-active-high;
164 };
165
166 vccq_sdhi2: regulator@4 {
167 compatible = "regulator-gpio";
168
169 regulator-name = "SDHI2 VccQ";
170 regulator-min-microvolt = <1800000>;
171 regulator-max-microvolt = <3300000>;
172
173 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
174 gpios-states = <1>;
175 states = <3300000 1
176 1800000 0>;
177 };
178
179 audio_clock: clock {
180 compatible = "fixed-clock";
181 #clock-cells = <0>;
182 clock-frequency = <11289600>;
183 clock-output-names = "audio_clock";
184 };
185
186 rsnd_ak4643: sound {
187 compatible = "simple-audio-card";
188
189 simple-audio-card,format = "left_j";
190 simple-audio-card,bitclock-master = <&sndcodec>;
191 simple-audio-card,frame-master = <&sndcodec>;
192
193 sndcpu: simple-audio-card,cpu {
194 sound-dai = <&rcar_sound>;
195 };
196
197 sndcodec: simple-audio-card,codec {
198 sound-dai = <&ak4643>;
199 clocks = <&audio_clock>;
200 };
201 };
202
203 vga-encoder {
204 compatible = "adi,adv7123";
205
206 ports {
207 #address-cells = <1>;
208 #size-cells = <0>;
209
210 port@0 {
211 reg = <0>;
212 adv7123_in: endpoint {
213 remote-endpoint = <&du_out_rgb>;
214 };
215 };
216 port@1 {
217 reg = <1>;
218 adv7123_out: endpoint {
219 remote-endpoint = <&vga_in>;
220 };
221 };
222 };
223 };
224
225 vga {
226 compatible = "vga-connector";
227
228 port {
229 vga_in: endpoint {
230 remote-endpoint = <&adv7123_out>;
231 };
232 };
233 };
234
235 hdmi-out {
236 compatible = "hdmi-connector";
237 type = "a";
238
239 port {
240 hdmi_con: endpoint {
241 remote-endpoint = <&adv7511_out>;
242 };
243 };
244 };
245
246 x2_clk: x2-clock {
247 compatible = "fixed-clock";
248 #clock-cells = <0>;
249 clock-frequency = <148500000>;
250 };
251
252 x13_clk: x13-clock {
253 compatible = "fixed-clock";
254 #clock-cells = <0>;
255 clock-frequency = <148500000>;
256 };
257
258 /*
259 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
260 * We use the I2C demuxer, so the desired IP core can be selected at runtime
261 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
262 * Note: For testing the I2C slave feature, it is convenient to connect this
263 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
264 * instantiate the slave device at runtime according to the documentation.
265 * You can then communicate with the slave via IIC3.
266 */
267 i2cexio: i2c@8 {
268 compatible = "i2c-demux-pinctrl";
269 i2c-parent = <&iic0>, <&i2c0>;
270 i2c-bus-name = "i2c-exio";
271 #address-cells = <1>;
272 #size-cells = <0>;
273 };
274};
275
276&du {
277 pinctrl-0 = <&du_pins>;
278 pinctrl-names = "default";
279 status = "okay";
280
281 clocks = <&mstp7_clks R8A7790_CLK_DU0>,
282 <&mstp7_clks R8A7790_CLK_DU1>,
283 <&mstp7_clks R8A7790_CLK_DU2>,
284 <&mstp7_clks R8A7790_CLK_LVDS0>,
285 <&mstp7_clks R8A7790_CLK_LVDS1>,
286 <&x13_clk>, <&x2_clk>;
287 clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1",
288 "dclkin.0", "dclkin.1";
289
290 ports {
291 port@0 {
292 endpoint {
293 remote-endpoint = <&adv7123_in>;
294 };
295 };
296 port@1 {
297 endpoint {
298 remote-endpoint = <&adv7511_in>;
299 };
300 };
301 port@2 {
302 lvds_connector: endpoint {
303 };
304 };
305 };
306};
307
308&extal_clk {
309 clock-frequency = <20000000>;
310};
311
312&pfc {
313 pinctrl-0 = <&scif_clk_pins>;
314 pinctrl-names = "default";
315
316 du_pins: du {
317 renesas,groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
318 renesas,function = "du";
319 };
320
321 scif0_pins: serial0 {
322 renesas,groups = "scif0_data";
323 renesas,function = "scif0";
324 };
325
326 scif_clk_pins: scif_clk {
327 renesas,groups = "scif_clk";
328 renesas,function = "scif_clk";
329 };
330
331 ether_pins: ether {
332 renesas,groups = "eth_link", "eth_mdio", "eth_rmii";
333 renesas,function = "eth";
334 };
335
336 phy1_pins: phy1 {
337 renesas,groups = "intc_irq0";
338 renesas,function = "intc";
339 };
340
341 scifa1_pins: serial1 {
342 renesas,groups = "scifa1_data";
343 renesas,function = "scifa1";
344 };
345
346 sdhi0_pins: sd0 {
347 renesas,groups = "sdhi0_data4", "sdhi0_ctrl";
348 renesas,function = "sdhi0";
349 };
350
351 sdhi2_pins: sd2 {
352 renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
353 renesas,function = "sdhi2";
354 };
355
356 mmc1_pins: mmc1 {
357 renesas,groups = "mmc1_data8", "mmc1_ctrl";
358 renesas,function = "mmc1";
359 };
360
361 qspi_pins: spi0 {
362 renesas,groups = "qspi_ctrl", "qspi_data4";
363 renesas,function = "qspi";
364 };
365
366 msiof1_pins: spi2 {
367 renesas,groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
368 "msiof1_tx";
369 renesas,function = "msiof1";
370 };
371
372 i2c0_pins: i2c0 {
373 renesas,groups = "i2c0";
374 renesas,function = "i2c0";
375 };
376
377 iic0_pins: iic0 {
378 renesas,groups = "iic0";
379 renesas,function = "iic0";
380 };
381
382 iic1_pins: iic1 {
383 renesas,groups = "iic1";
384 renesas,function = "iic1";
385 };
386
387 iic2_pins: iic2 {
388 renesas,groups = "iic2";
389 renesas,function = "iic2";
390 };
391
392 iic3_pins: iic3 {
393 renesas,groups = "iic3";
394 renesas,function = "iic3";
395 };
396
397 hsusb_pins: hsusb {
398 renesas,groups = "usb0_ovc_vbus";
399 renesas,function = "usb0";
400 };
401
402 usb0_pins: usb0 {
403 renesas,groups = "usb0";
404 renesas,function = "usb0";
405 };
406
407 usb1_pins: usb1 {
408 renesas,groups = "usb1";
409 renesas,function = "usb1";
410 };
411
412 usb2_pins: usb2 {
413 renesas,groups = "usb2";
414 renesas,function = "usb2";
415 };
416
417 vin1_pins: vin {
418 renesas,groups = "vin1_data8", "vin1_clk";
419 renesas,function = "vin1";
420 };
421
422 sound_pins: sound {
423 renesas,groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
424 renesas,function = "ssi";
425 };
426
427 sound_clk_pins: sound_clk {
428 renesas,groups = "audio_clk_a";
429 renesas,function = "audio_clk";
430 };
431};
432
433ðer {
434 pinctrl-0 = <ðer_pins &phy1_pins>;
435 pinctrl-names = "default";
436
437 phy-handle = <&phy1>;
438 renesas,ether-link-active-low;
439 status = "okay";
440
441 phy1: ethernet-phy@1 {
442 reg = <1>;
443 interrupt-parent = <&irqc0>;
444 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
445 micrel,led-mode = <1>;
446 };
447};
448
449&cmt0 {
450 status = "okay";
451};
452
453&mmcif1 {
454 pinctrl-0 = <&mmc1_pins>;
455 pinctrl-names = "default";
456
457 vmmc-supply = <&fixedregulator3v3>;
458 bus-width = <8>;
459 non-removable;
460 status = "okay";
461};
462
463&sata1 {
464 status = "okay";
465};
466
467&qspi {
468 pinctrl-0 = <&qspi_pins>;
469 pinctrl-names = "default";
470
471 status = "okay";
472
473 flash: flash@0 {
474 compatible = "spansion,s25fl512s", "jedec,spi-nor";
475 reg = <0>;
476 spi-max-frequency = <30000000>;
477 spi-tx-bus-width = <4>;
478 spi-rx-bus-width = <4>;
479 spi-cpha;
480 spi-cpol;
481 m25p,fast-read;
482
483 partitions {
484 compatible = "fixed-partitions";
485 #address-cells = <1>;
486 #size-cells = <1>;
487
488 partition@0 {
489 label = "loader";
490 reg = <0x00000000 0x00040000>;
491 read-only;
492 };
493 partition@40000 {
494 label = "user";
495 reg = <0x00040000 0x00400000>;
496 read-only;
497 };
498 partition@440000 {
499 label = "flash";
500 reg = <0x00440000 0x03bc0000>;
501 };
502 };
503 };
504};
505
506&scif0 {
507 pinctrl-0 = <&scif0_pins>;
508 pinctrl-names = "default";
509
510 status = "okay";
511};
512
513&scifa1 {
514 pinctrl-0 = <&scifa1_pins>;
515 pinctrl-names = "default";
516
517 status = "okay";
518};
519
520&scif_clk {
521 clock-frequency = <14745600>;
522 status = "okay";
523};
524
525&msiof1 {
526 pinctrl-0 = <&msiof1_pins>;
527 pinctrl-names = "default";
528
529 status = "okay";
530
531 pmic: pmic@0 {
532 compatible = "renesas,r2a11302ft";
533 reg = <0>;
534 spi-max-frequency = <6000000>;
535 spi-cpol;
536 spi-cpha;
537 };
538};
539
540&sdhi0 {
541 pinctrl-0 = <&sdhi0_pins>;
542 pinctrl-names = "default";
543
544 vmmc-supply = <&vcc_sdhi0>;
545 vqmmc-supply = <&vccq_sdhi0>;
546 cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
547 status = "okay";
548};
549
550&sdhi2 {
551 pinctrl-0 = <&sdhi2_pins>;
552 pinctrl-names = "default";
553
554 vmmc-supply = <&vcc_sdhi2>;
555 vqmmc-supply = <&vccq_sdhi2>;
556 cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
557 status = "okay";
558};
559
560&cpu0 {
561 cpu0-supply = <&vdd_dvfs>;
562};
563
564&i2c0 {
565 pinctrl-0 = <&i2c0_pins>;
566 pinctrl-names = "i2c-exio";
567};
568
569&iic0 {
570 pinctrl-0 = <&iic0_pins>;
571 pinctrl-names = "i2c-exio";
572};
573
574&iic1 {
575 status = "okay";
576 pinctrl-0 = <&iic1_pins>;
577 pinctrl-names = "default";
578};
579
580&iic2 {
581 status = "okay";
582 pinctrl-0 = <&iic2_pins>;
583 pinctrl-names = "default";
584
585 clock-frequency = <100000>;
586
587 ak4643: codec@12 {
588 compatible = "asahi-kasei,ak4643";
589 #sound-dai-cells = <0>;
590 reg = <0x12>;
591 };
592
593 composite-in@20 {
594 compatible = "adi,adv7180";
595 reg = <0x20>;
596 remote = <&vin1>;
597
598 port {
599 adv7180: endpoint {
600 bus-width = <8>;
601 remote-endpoint = <&vin1ep0>;
602 };
603 };
604 };
605
606 hdmi@39 {
607 compatible = "adi,adv7511w";
608 reg = <0x39>;
609 interrupt-parent = <&gpio1>;
610 interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
611
612 adi,input-depth = <8>;
613 adi,input-colorspace = "rgb";
614 adi,input-clock = "1x";
615 adi,input-style = <1>;
616 adi,input-justification = "evenly";
617
618 ports {
619 #address-cells = <1>;
620 #size-cells = <0>;
621
622 port@0 {
623 reg = <0>;
624 adv7511_in: endpoint {
625 remote-endpoint = <&du_out_lvds0>;
626 };
627 };
628
629 port@1 {
630 reg = <1>;
631 adv7511_out: endpoint {
632 remote-endpoint = <&hdmi_con>;
633 };
634 };
635 };
636 };
637};
638
639&iic3 {
640 pinctrl-names = "default";
641 pinctrl-0 = <&iic3_pins>;
642 status = "okay";
643
644 pmic@58 {
645 compatible = "dlg,da9063";
646 reg = <0x58>;
647 interrupt-parent = <&irqc0>;
648 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
649 interrupt-controller;
650
651 rtc {
652 compatible = "dlg,da9063-rtc";
653 };
654
655 wdt {
656 compatible = "dlg,da9063-watchdog";
657 };
658 };
659
660 vdd_dvfs: regulator@68 {
661 compatible = "dlg,da9210";
662 reg = <0x68>;
663 interrupt-parent = <&irqc0>;
664 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
665
666 regulator-min-microvolt = <1000000>;
667 regulator-max-microvolt = <1000000>;
668 regulator-boot-on;
669 regulator-always-on;
670 };
671};
672
673&pci0 {
674 status = "okay";
675 pinctrl-0 = <&usb0_pins>;
676 pinctrl-names = "default";
677};
678
679&pci1 {
680 status = "okay";
681 pinctrl-0 = <&usb1_pins>;
682 pinctrl-names = "default";
683};
684
685&xhci {
686 status = "okay";
687 pinctrl-0 = <&usb2_pins>;
688 pinctrl-names = "default";
689};
690
691&pci2 {
692 status = "okay";
693 pinctrl-0 = <&usb2_pins>;
694 pinctrl-names = "default";
695};
696
697&hsusb {
698 status = "okay";
699 pinctrl-0 = <&hsusb_pins>;
700 pinctrl-names = "default";
701 renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
702};
703
704&usbphy {
705 status = "okay";
706};
707
708/* composite video input */
709&vin1 {
710 pinctrl-0 = <&vin1_pins>;
711 pinctrl-names = "default";
712
713 status = "okay";
714
715 port {
716 #address-cells = <1>;
717 #size-cells = <0>;
718
719 vin1ep0: endpoint {
720 remote-endpoint = <&adv7180>;
721 bus-width = <8>;
722 };
723 };
724};
725
726&rcar_sound {
727 pinctrl-0 = <&sound_pins &sound_clk_pins>;
728 pinctrl-names = "default";
729
730 /* Single DAI */
731 #sound-dai-cells = <0>;
732
733 status = "okay";
734
735 rcar_sound,dai {
736 dai0 {
737 playback = <&ssi0 &src2 &dvc0>;
738 capture = <&ssi1 &src3 &dvc1>;
739 };
740 };
741};
742
743&ssi1 {
744 shared-pin;
745};