Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
4 *
5 * Copyright (C) 2002 - 2011 Paul Mundt
6 * Copyright (C) 2015 Glider bvba
7 * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
8 *
9 * based off of the old drivers/char/sh-sci.c by:
10 *
11 * Copyright (C) 1999, 2000 Niibe Yutaka
12 * Copyright (C) 2000 Sugioka Toshinobu
13 * Modified to support multiple serial ports. Stuart Menefy (May 2000).
14 * Modified to support SecureEdge. David McCullough (2002)
15 * Modified to support SH7300 SCIF. Takashi Kusuda (Jun 2003).
16 * Removed SH7300 support (Jul 2007).
17 */
18#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
19#define SUPPORT_SYSRQ
20#endif
21
22#undef DEBUG
23
24#include <linux/clk.h>
25#include <linux/console.h>
26#include <linux/ctype.h>
27#include <linux/cpufreq.h>
28#include <linux/delay.h>
29#include <linux/dmaengine.h>
30#include <linux/dma-mapping.h>
31#include <linux/err.h>
32#include <linux/errno.h>
33#include <linux/init.h>
34#include <linux/interrupt.h>
35#include <linux/ioport.h>
36#include <linux/ktime.h>
37#include <linux/major.h>
38#include <linux/module.h>
39#include <linux/mm.h>
40#include <linux/of.h>
41#include <linux/of_device.h>
42#include <linux/platform_device.h>
43#include <linux/pm_runtime.h>
44#include <linux/scatterlist.h>
45#include <linux/serial.h>
46#include <linux/serial_sci.h>
47#include <linux/sh_dma.h>
48#include <linux/slab.h>
49#include <linux/string.h>
50#include <linux/sysrq.h>
51#include <linux/timer.h>
52#include <linux/tty.h>
53#include <linux/tty_flip.h>
54
55#ifdef CONFIG_SUPERH
56#include <asm/sh_bios.h>
57#endif
58
59#include "serial_mctrl_gpio.h"
60#include "sh-sci.h"
61
62/* Offsets into the sci_port->irqs array */
63enum {
64 SCIx_ERI_IRQ,
65 SCIx_RXI_IRQ,
66 SCIx_TXI_IRQ,
67 SCIx_BRI_IRQ,
68 SCIx_DRI_IRQ,
69 SCIx_TEI_IRQ,
70 SCIx_NR_IRQS,
71
72 SCIx_MUX_IRQ = SCIx_NR_IRQS, /* special case */
73};
74
75#define SCIx_IRQ_IS_MUXED(port) \
76 ((port)->irqs[SCIx_ERI_IRQ] == \
77 (port)->irqs[SCIx_RXI_IRQ]) || \
78 ((port)->irqs[SCIx_ERI_IRQ] && \
79 ((port)->irqs[SCIx_RXI_IRQ] < 0))
80
81enum SCI_CLKS {
82 SCI_FCK, /* Functional Clock */
83 SCI_SCK, /* Optional External Clock */
84 SCI_BRG_INT, /* Optional BRG Internal Clock Source */
85 SCI_SCIF_CLK, /* Optional BRG External Clock Source */
86 SCI_NUM_CLKS
87};
88
89/* Bit x set means sampling rate x + 1 is supported */
90#define SCI_SR(x) BIT((x) - 1)
91#define SCI_SR_RANGE(x, y) GENMASK((y) - 1, (x) - 1)
92
93#define SCI_SR_SCIFAB SCI_SR(5) | SCI_SR(7) | SCI_SR(11) | \
94 SCI_SR(13) | SCI_SR(16) | SCI_SR(17) | \
95 SCI_SR(19) | SCI_SR(27)
96
97#define min_sr(_port) ffs((_port)->sampling_rate_mask)
98#define max_sr(_port) fls((_port)->sampling_rate_mask)
99
100/* Iterate over all supported sampling rates, from high to low */
101#define for_each_sr(_sr, _port) \
102 for ((_sr) = max_sr(_port); (_sr) >= min_sr(_port); (_sr)--) \
103 if ((_port)->sampling_rate_mask & SCI_SR((_sr)))
104
105struct plat_sci_reg {
106 u8 offset, size;
107};
108
109struct sci_port_params {
110 const struct plat_sci_reg regs[SCIx_NR_REGS];
111 unsigned int fifosize;
112 unsigned int overrun_reg;
113 unsigned int overrun_mask;
114 unsigned int sampling_rate_mask;
115 unsigned int error_mask;
116 unsigned int error_clear;
117};
118
119struct sci_port {
120 struct uart_port port;
121
122 /* Platform configuration */
123 const struct sci_port_params *params;
124 const struct plat_sci_port *cfg;
125 unsigned int sampling_rate_mask;
126 resource_size_t reg_size;
127 struct mctrl_gpios *gpios;
128
129 /* Clocks */
130 struct clk *clks[SCI_NUM_CLKS];
131 unsigned long clk_rates[SCI_NUM_CLKS];
132
133 int irqs[SCIx_NR_IRQS];
134 char *irqstr[SCIx_NR_IRQS];
135
136 struct dma_chan *chan_tx;
137 struct dma_chan *chan_rx;
138
139#ifdef CONFIG_SERIAL_SH_SCI_DMA
140 struct dma_chan *chan_tx_saved;
141 struct dma_chan *chan_rx_saved;
142 dma_cookie_t cookie_tx;
143 dma_cookie_t cookie_rx[2];
144 dma_cookie_t active_rx;
145 dma_addr_t tx_dma_addr;
146 unsigned int tx_dma_len;
147 struct scatterlist sg_rx[2];
148 void *rx_buf[2];
149 size_t buf_len_rx;
150 struct work_struct work_tx;
151 struct hrtimer rx_timer;
152 unsigned int rx_timeout; /* microseconds */
153#endif
154 unsigned int rx_frame;
155 int rx_trigger;
156 struct timer_list rx_fifo_timer;
157 int rx_fifo_timeout;
158 u16 hscif_tot;
159
160 bool has_rtscts;
161 bool autorts;
162};
163
164#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS
165
166static struct sci_port sci_ports[SCI_NPORTS];
167static unsigned long sci_ports_in_use;
168static struct uart_driver sci_uart_driver;
169
170static inline struct sci_port *
171to_sci_port(struct uart_port *uart)
172{
173 return container_of(uart, struct sci_port, port);
174}
175
176static const struct sci_port_params sci_port_params[SCIx_NR_REGTYPES] = {
177 /*
178 * Common SCI definitions, dependent on the port's regshift
179 * value.
180 */
181 [SCIx_SCI_REGTYPE] = {
182 .regs = {
183 [SCSMR] = { 0x00, 8 },
184 [SCBRR] = { 0x01, 8 },
185 [SCSCR] = { 0x02, 8 },
186 [SCxTDR] = { 0x03, 8 },
187 [SCxSR] = { 0x04, 8 },
188 [SCxRDR] = { 0x05, 8 },
189 },
190 .fifosize = 1,
191 .overrun_reg = SCxSR,
192 .overrun_mask = SCI_ORER,
193 .sampling_rate_mask = SCI_SR(32),
194 .error_mask = SCI_DEFAULT_ERROR_MASK | SCI_ORER,
195 .error_clear = SCI_ERROR_CLEAR & ~SCI_ORER,
196 },
197
198 /*
199 * Common definitions for legacy IrDA ports.
200 */
201 [SCIx_IRDA_REGTYPE] = {
202 .regs = {
203 [SCSMR] = { 0x00, 8 },
204 [SCBRR] = { 0x02, 8 },
205 [SCSCR] = { 0x04, 8 },
206 [SCxTDR] = { 0x06, 8 },
207 [SCxSR] = { 0x08, 16 },
208 [SCxRDR] = { 0x0a, 8 },
209 [SCFCR] = { 0x0c, 8 },
210 [SCFDR] = { 0x0e, 16 },
211 },
212 .fifosize = 1,
213 .overrun_reg = SCxSR,
214 .overrun_mask = SCI_ORER,
215 .sampling_rate_mask = SCI_SR(32),
216 .error_mask = SCI_DEFAULT_ERROR_MASK | SCI_ORER,
217 .error_clear = SCI_ERROR_CLEAR & ~SCI_ORER,
218 },
219
220 /*
221 * Common SCIFA definitions.
222 */
223 [SCIx_SCIFA_REGTYPE] = {
224 .regs = {
225 [SCSMR] = { 0x00, 16 },
226 [SCBRR] = { 0x04, 8 },
227 [SCSCR] = { 0x08, 16 },
228 [SCxTDR] = { 0x20, 8 },
229 [SCxSR] = { 0x14, 16 },
230 [SCxRDR] = { 0x24, 8 },
231 [SCFCR] = { 0x18, 16 },
232 [SCFDR] = { 0x1c, 16 },
233 [SCPCR] = { 0x30, 16 },
234 [SCPDR] = { 0x34, 16 },
235 },
236 .fifosize = 64,
237 .overrun_reg = SCxSR,
238 .overrun_mask = SCIFA_ORER,
239 .sampling_rate_mask = SCI_SR_SCIFAB,
240 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER,
241 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER,
242 },
243
244 /*
245 * Common SCIFB definitions.
246 */
247 [SCIx_SCIFB_REGTYPE] = {
248 .regs = {
249 [SCSMR] = { 0x00, 16 },
250 [SCBRR] = { 0x04, 8 },
251 [SCSCR] = { 0x08, 16 },
252 [SCxTDR] = { 0x40, 8 },
253 [SCxSR] = { 0x14, 16 },
254 [SCxRDR] = { 0x60, 8 },
255 [SCFCR] = { 0x18, 16 },
256 [SCTFDR] = { 0x38, 16 },
257 [SCRFDR] = { 0x3c, 16 },
258 [SCPCR] = { 0x30, 16 },
259 [SCPDR] = { 0x34, 16 },
260 },
261 .fifosize = 256,
262 .overrun_reg = SCxSR,
263 .overrun_mask = SCIFA_ORER,
264 .sampling_rate_mask = SCI_SR_SCIFAB,
265 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER,
266 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER,
267 },
268
269 /*
270 * Common SH-2(A) SCIF definitions for ports with FIFO data
271 * count registers.
272 */
273 [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
274 .regs = {
275 [SCSMR] = { 0x00, 16 },
276 [SCBRR] = { 0x04, 8 },
277 [SCSCR] = { 0x08, 16 },
278 [SCxTDR] = { 0x0c, 8 },
279 [SCxSR] = { 0x10, 16 },
280 [SCxRDR] = { 0x14, 8 },
281 [SCFCR] = { 0x18, 16 },
282 [SCFDR] = { 0x1c, 16 },
283 [SCSPTR] = { 0x20, 16 },
284 [SCLSR] = { 0x24, 16 },
285 },
286 .fifosize = 16,
287 .overrun_reg = SCLSR,
288 .overrun_mask = SCLSR_ORER,
289 .sampling_rate_mask = SCI_SR(32),
290 .error_mask = SCIF_DEFAULT_ERROR_MASK,
291 .error_clear = SCIF_ERROR_CLEAR,
292 },
293
294 /*
295 * The "SCIFA" that is in RZ/T and RZ/A2.
296 * It looks like a normal SCIF with FIFO data, but with a
297 * compressed address space. Also, the break out of interrupts
298 * are different: ERI/BRI, RXI, TXI, TEI, DRI.
299 */
300 [SCIx_RZ_SCIFA_REGTYPE] = {
301 .regs = {
302 [SCSMR] = { 0x00, 16 },
303 [SCBRR] = { 0x02, 8 },
304 [SCSCR] = { 0x04, 16 },
305 [SCxTDR] = { 0x06, 8 },
306 [SCxSR] = { 0x08, 16 },
307 [SCxRDR] = { 0x0A, 8 },
308 [SCFCR] = { 0x0C, 16 },
309 [SCFDR] = { 0x0E, 16 },
310 [SCSPTR] = { 0x10, 16 },
311 [SCLSR] = { 0x12, 16 },
312 },
313 .fifosize = 16,
314 .overrun_reg = SCLSR,
315 .overrun_mask = SCLSR_ORER,
316 .sampling_rate_mask = SCI_SR(32),
317 .error_mask = SCIF_DEFAULT_ERROR_MASK,
318 .error_clear = SCIF_ERROR_CLEAR,
319 },
320
321 /*
322 * Common SH-3 SCIF definitions.
323 */
324 [SCIx_SH3_SCIF_REGTYPE] = {
325 .regs = {
326 [SCSMR] = { 0x00, 8 },
327 [SCBRR] = { 0x02, 8 },
328 [SCSCR] = { 0x04, 8 },
329 [SCxTDR] = { 0x06, 8 },
330 [SCxSR] = { 0x08, 16 },
331 [SCxRDR] = { 0x0a, 8 },
332 [SCFCR] = { 0x0c, 8 },
333 [SCFDR] = { 0x0e, 16 },
334 },
335 .fifosize = 16,
336 .overrun_reg = SCLSR,
337 .overrun_mask = SCLSR_ORER,
338 .sampling_rate_mask = SCI_SR(32),
339 .error_mask = SCIF_DEFAULT_ERROR_MASK,
340 .error_clear = SCIF_ERROR_CLEAR,
341 },
342
343 /*
344 * Common SH-4(A) SCIF(B) definitions.
345 */
346 [SCIx_SH4_SCIF_REGTYPE] = {
347 .regs = {
348 [SCSMR] = { 0x00, 16 },
349 [SCBRR] = { 0x04, 8 },
350 [SCSCR] = { 0x08, 16 },
351 [SCxTDR] = { 0x0c, 8 },
352 [SCxSR] = { 0x10, 16 },
353 [SCxRDR] = { 0x14, 8 },
354 [SCFCR] = { 0x18, 16 },
355 [SCFDR] = { 0x1c, 16 },
356 [SCSPTR] = { 0x20, 16 },
357 [SCLSR] = { 0x24, 16 },
358 },
359 .fifosize = 16,
360 .overrun_reg = SCLSR,
361 .overrun_mask = SCLSR_ORER,
362 .sampling_rate_mask = SCI_SR(32),
363 .error_mask = SCIF_DEFAULT_ERROR_MASK,
364 .error_clear = SCIF_ERROR_CLEAR,
365 },
366
367 /*
368 * Common SCIF definitions for ports with a Baud Rate Generator for
369 * External Clock (BRG).
370 */
371 [SCIx_SH4_SCIF_BRG_REGTYPE] = {
372 .regs = {
373 [SCSMR] = { 0x00, 16 },
374 [SCBRR] = { 0x04, 8 },
375 [SCSCR] = { 0x08, 16 },
376 [SCxTDR] = { 0x0c, 8 },
377 [SCxSR] = { 0x10, 16 },
378 [SCxRDR] = { 0x14, 8 },
379 [SCFCR] = { 0x18, 16 },
380 [SCFDR] = { 0x1c, 16 },
381 [SCSPTR] = { 0x20, 16 },
382 [SCLSR] = { 0x24, 16 },
383 [SCDL] = { 0x30, 16 },
384 [SCCKS] = { 0x34, 16 },
385 },
386 .fifosize = 16,
387 .overrun_reg = SCLSR,
388 .overrun_mask = SCLSR_ORER,
389 .sampling_rate_mask = SCI_SR(32),
390 .error_mask = SCIF_DEFAULT_ERROR_MASK,
391 .error_clear = SCIF_ERROR_CLEAR,
392 },
393
394 /*
395 * Common HSCIF definitions.
396 */
397 [SCIx_HSCIF_REGTYPE] = {
398 .regs = {
399 [SCSMR] = { 0x00, 16 },
400 [SCBRR] = { 0x04, 8 },
401 [SCSCR] = { 0x08, 16 },
402 [SCxTDR] = { 0x0c, 8 },
403 [SCxSR] = { 0x10, 16 },
404 [SCxRDR] = { 0x14, 8 },
405 [SCFCR] = { 0x18, 16 },
406 [SCFDR] = { 0x1c, 16 },
407 [SCSPTR] = { 0x20, 16 },
408 [SCLSR] = { 0x24, 16 },
409 [HSSRR] = { 0x40, 16 },
410 [SCDL] = { 0x30, 16 },
411 [SCCKS] = { 0x34, 16 },
412 [HSRTRGR] = { 0x54, 16 },
413 [HSTTRGR] = { 0x58, 16 },
414 },
415 .fifosize = 128,
416 .overrun_reg = SCLSR,
417 .overrun_mask = SCLSR_ORER,
418 .sampling_rate_mask = SCI_SR_RANGE(8, 32),
419 .error_mask = SCIF_DEFAULT_ERROR_MASK,
420 .error_clear = SCIF_ERROR_CLEAR,
421 },
422
423 /*
424 * Common SH-4(A) SCIF(B) definitions for ports without an SCSPTR
425 * register.
426 */
427 [SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE] = {
428 .regs = {
429 [SCSMR] = { 0x00, 16 },
430 [SCBRR] = { 0x04, 8 },
431 [SCSCR] = { 0x08, 16 },
432 [SCxTDR] = { 0x0c, 8 },
433 [SCxSR] = { 0x10, 16 },
434 [SCxRDR] = { 0x14, 8 },
435 [SCFCR] = { 0x18, 16 },
436 [SCFDR] = { 0x1c, 16 },
437 [SCLSR] = { 0x24, 16 },
438 },
439 .fifosize = 16,
440 .overrun_reg = SCLSR,
441 .overrun_mask = SCLSR_ORER,
442 .sampling_rate_mask = SCI_SR(32),
443 .error_mask = SCIF_DEFAULT_ERROR_MASK,
444 .error_clear = SCIF_ERROR_CLEAR,
445 },
446
447 /*
448 * Common SH-4(A) SCIF(B) definitions for ports with FIFO data
449 * count registers.
450 */
451 [SCIx_SH4_SCIF_FIFODATA_REGTYPE] = {
452 .regs = {
453 [SCSMR] = { 0x00, 16 },
454 [SCBRR] = { 0x04, 8 },
455 [SCSCR] = { 0x08, 16 },
456 [SCxTDR] = { 0x0c, 8 },
457 [SCxSR] = { 0x10, 16 },
458 [SCxRDR] = { 0x14, 8 },
459 [SCFCR] = { 0x18, 16 },
460 [SCFDR] = { 0x1c, 16 },
461 [SCTFDR] = { 0x1c, 16 }, /* aliased to SCFDR */
462 [SCRFDR] = { 0x20, 16 },
463 [SCSPTR] = { 0x24, 16 },
464 [SCLSR] = { 0x28, 16 },
465 },
466 .fifosize = 16,
467 .overrun_reg = SCLSR,
468 .overrun_mask = SCLSR_ORER,
469 .sampling_rate_mask = SCI_SR(32),
470 .error_mask = SCIF_DEFAULT_ERROR_MASK,
471 .error_clear = SCIF_ERROR_CLEAR,
472 },
473
474 /*
475 * SH7705-style SCIF(B) ports, lacking both SCSPTR and SCLSR
476 * registers.
477 */
478 [SCIx_SH7705_SCIF_REGTYPE] = {
479 .regs = {
480 [SCSMR] = { 0x00, 16 },
481 [SCBRR] = { 0x04, 8 },
482 [SCSCR] = { 0x08, 16 },
483 [SCxTDR] = { 0x20, 8 },
484 [SCxSR] = { 0x14, 16 },
485 [SCxRDR] = { 0x24, 8 },
486 [SCFCR] = { 0x18, 16 },
487 [SCFDR] = { 0x1c, 16 },
488 },
489 .fifosize = 64,
490 .overrun_reg = SCxSR,
491 .overrun_mask = SCIFA_ORER,
492 .sampling_rate_mask = SCI_SR(16),
493 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER,
494 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER,
495 },
496};
497
498#define sci_getreg(up, offset) (&to_sci_port(up)->params->regs[offset])
499
500/*
501 * The "offset" here is rather misleading, in that it refers to an enum
502 * value relative to the port mapping rather than the fixed offset
503 * itself, which needs to be manually retrieved from the platform's
504 * register map for the given port.
505 */
506static unsigned int sci_serial_in(struct uart_port *p, int offset)
507{
508 const struct plat_sci_reg *reg = sci_getreg(p, offset);
509
510 if (reg->size == 8)
511 return ioread8(p->membase + (reg->offset << p->regshift));
512 else if (reg->size == 16)
513 return ioread16(p->membase + (reg->offset << p->regshift));
514 else
515 WARN(1, "Invalid register access\n");
516
517 return 0;
518}
519
520static void sci_serial_out(struct uart_port *p, int offset, int value)
521{
522 const struct plat_sci_reg *reg = sci_getreg(p, offset);
523
524 if (reg->size == 8)
525 iowrite8(value, p->membase + (reg->offset << p->regshift));
526 else if (reg->size == 16)
527 iowrite16(value, p->membase + (reg->offset << p->regshift));
528 else
529 WARN(1, "Invalid register access\n");
530}
531
532static void sci_port_enable(struct sci_port *sci_port)
533{
534 unsigned int i;
535
536 if (!sci_port->port.dev)
537 return;
538
539 pm_runtime_get_sync(sci_port->port.dev);
540
541 for (i = 0; i < SCI_NUM_CLKS; i++) {
542 clk_prepare_enable(sci_port->clks[i]);
543 sci_port->clk_rates[i] = clk_get_rate(sci_port->clks[i]);
544 }
545 sci_port->port.uartclk = sci_port->clk_rates[SCI_FCK];
546}
547
548static void sci_port_disable(struct sci_port *sci_port)
549{
550 unsigned int i;
551
552 if (!sci_port->port.dev)
553 return;
554
555 for (i = SCI_NUM_CLKS; i-- > 0; )
556 clk_disable_unprepare(sci_port->clks[i]);
557
558 pm_runtime_put_sync(sci_port->port.dev);
559}
560
561static inline unsigned long port_rx_irq_mask(struct uart_port *port)
562{
563 /*
564 * Not all ports (such as SCIFA) will support REIE. Rather than
565 * special-casing the port type, we check the port initialization
566 * IRQ enable mask to see whether the IRQ is desired at all. If
567 * it's unset, it's logically inferred that there's no point in
568 * testing for it.
569 */
570 return SCSCR_RIE | (to_sci_port(port)->cfg->scscr & SCSCR_REIE);
571}
572
573static void sci_start_tx(struct uart_port *port)
574{
575 struct sci_port *s = to_sci_port(port);
576 unsigned short ctrl;
577
578#ifdef CONFIG_SERIAL_SH_SCI_DMA
579 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
580 u16 new, scr = serial_port_in(port, SCSCR);
581 if (s->chan_tx)
582 new = scr | SCSCR_TDRQE;
583 else
584 new = scr & ~SCSCR_TDRQE;
585 if (new != scr)
586 serial_port_out(port, SCSCR, new);
587 }
588
589 if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) &&
590 dma_submit_error(s->cookie_tx)) {
591 s->cookie_tx = 0;
592 schedule_work(&s->work_tx);
593 }
594#endif
595
596 if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
597 /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
598 ctrl = serial_port_in(port, SCSCR);
599 serial_port_out(port, SCSCR, ctrl | SCSCR_TIE);
600 }
601}
602
603static void sci_stop_tx(struct uart_port *port)
604{
605 unsigned short ctrl;
606
607 /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
608 ctrl = serial_port_in(port, SCSCR);
609
610 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
611 ctrl &= ~SCSCR_TDRQE;
612
613 ctrl &= ~SCSCR_TIE;
614
615 serial_port_out(port, SCSCR, ctrl);
616}
617
618static void sci_start_rx(struct uart_port *port)
619{
620 unsigned short ctrl;
621
622 ctrl = serial_port_in(port, SCSCR) | port_rx_irq_mask(port);
623
624 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
625 ctrl &= ~SCSCR_RDRQE;
626
627 serial_port_out(port, SCSCR, ctrl);
628}
629
630static void sci_stop_rx(struct uart_port *port)
631{
632 unsigned short ctrl;
633
634 ctrl = serial_port_in(port, SCSCR);
635
636 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
637 ctrl &= ~SCSCR_RDRQE;
638
639 ctrl &= ~port_rx_irq_mask(port);
640
641 serial_port_out(port, SCSCR, ctrl);
642}
643
644static void sci_clear_SCxSR(struct uart_port *port, unsigned int mask)
645{
646 if (port->type == PORT_SCI) {
647 /* Just store the mask */
648 serial_port_out(port, SCxSR, mask);
649 } else if (to_sci_port(port)->params->overrun_mask == SCIFA_ORER) {
650 /* SCIFA/SCIFB and SCIF on SH7705/SH7720/SH7721 */
651 /* Only clear the status bits we want to clear */
652 serial_port_out(port, SCxSR,
653 serial_port_in(port, SCxSR) & mask);
654 } else {
655 /* Store the mask, clear parity/framing errors */
656 serial_port_out(port, SCxSR, mask & ~(SCIF_FERC | SCIF_PERC));
657 }
658}
659
660#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \
661 defined(CONFIG_SERIAL_SH_SCI_EARLYCON)
662
663#ifdef CONFIG_CONSOLE_POLL
664static int sci_poll_get_char(struct uart_port *port)
665{
666 unsigned short status;
667 int c;
668
669 do {
670 status = serial_port_in(port, SCxSR);
671 if (status & SCxSR_ERRORS(port)) {
672 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port));
673 continue;
674 }
675 break;
676 } while (1);
677
678 if (!(status & SCxSR_RDxF(port)))
679 return NO_POLL_CHAR;
680
681 c = serial_port_in(port, SCxRDR);
682
683 /* Dummy read */
684 serial_port_in(port, SCxSR);
685 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
686
687 return c;
688}
689#endif
690
691static void sci_poll_put_char(struct uart_port *port, unsigned char c)
692{
693 unsigned short status;
694
695 do {
696 status = serial_port_in(port, SCxSR);
697 } while (!(status & SCxSR_TDxE(port)));
698
699 serial_port_out(port, SCxTDR, c);
700 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
701}
702#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE ||
703 CONFIG_SERIAL_SH_SCI_EARLYCON */
704
705static void sci_init_pins(struct uart_port *port, unsigned int cflag)
706{
707 struct sci_port *s = to_sci_port(port);
708
709 /*
710 * Use port-specific handler if provided.
711 */
712 if (s->cfg->ops && s->cfg->ops->init_pins) {
713 s->cfg->ops->init_pins(port, cflag);
714 return;
715 }
716
717 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
718 u16 data = serial_port_in(port, SCPDR);
719 u16 ctrl = serial_port_in(port, SCPCR);
720
721 /* Enable RXD and TXD pin functions */
722 ctrl &= ~(SCPCR_RXDC | SCPCR_TXDC);
723 if (to_sci_port(port)->has_rtscts) {
724 /* RTS# is output, active low, unless autorts */
725 if (!(port->mctrl & TIOCM_RTS)) {
726 ctrl |= SCPCR_RTSC;
727 data |= SCPDR_RTSD;
728 } else if (!s->autorts) {
729 ctrl |= SCPCR_RTSC;
730 data &= ~SCPDR_RTSD;
731 } else {
732 /* Enable RTS# pin function */
733 ctrl &= ~SCPCR_RTSC;
734 }
735 /* Enable CTS# pin function */
736 ctrl &= ~SCPCR_CTSC;
737 }
738 serial_port_out(port, SCPDR, data);
739 serial_port_out(port, SCPCR, ctrl);
740 } else if (sci_getreg(port, SCSPTR)->size) {
741 u16 status = serial_port_in(port, SCSPTR);
742
743 /* RTS# is always output; and active low, unless autorts */
744 status |= SCSPTR_RTSIO;
745 if (!(port->mctrl & TIOCM_RTS))
746 status |= SCSPTR_RTSDT;
747 else if (!s->autorts)
748 status &= ~SCSPTR_RTSDT;
749 /* CTS# and SCK are inputs */
750 status &= ~(SCSPTR_CTSIO | SCSPTR_SCKIO);
751 serial_port_out(port, SCSPTR, status);
752 }
753}
754
755static int sci_txfill(struct uart_port *port)
756{
757 struct sci_port *s = to_sci_port(port);
758 unsigned int fifo_mask = (s->params->fifosize << 1) - 1;
759 const struct plat_sci_reg *reg;
760
761 reg = sci_getreg(port, SCTFDR);
762 if (reg->size)
763 return serial_port_in(port, SCTFDR) & fifo_mask;
764
765 reg = sci_getreg(port, SCFDR);
766 if (reg->size)
767 return serial_port_in(port, SCFDR) >> 8;
768
769 return !(serial_port_in(port, SCxSR) & SCI_TDRE);
770}
771
772static int sci_txroom(struct uart_port *port)
773{
774 return port->fifosize - sci_txfill(port);
775}
776
777static int sci_rxfill(struct uart_port *port)
778{
779 struct sci_port *s = to_sci_port(port);
780 unsigned int fifo_mask = (s->params->fifosize << 1) - 1;
781 const struct plat_sci_reg *reg;
782
783 reg = sci_getreg(port, SCRFDR);
784 if (reg->size)
785 return serial_port_in(port, SCRFDR) & fifo_mask;
786
787 reg = sci_getreg(port, SCFDR);
788 if (reg->size)
789 return serial_port_in(port, SCFDR) & fifo_mask;
790
791 return (serial_port_in(port, SCxSR) & SCxSR_RDxF(port)) != 0;
792}
793
794/* ********************************************************************** *
795 * the interrupt related routines *
796 * ********************************************************************** */
797
798static void sci_transmit_chars(struct uart_port *port)
799{
800 struct circ_buf *xmit = &port->state->xmit;
801 unsigned int stopped = uart_tx_stopped(port);
802 unsigned short status;
803 unsigned short ctrl;
804 int count;
805
806 status = serial_port_in(port, SCxSR);
807 if (!(status & SCxSR_TDxE(port))) {
808 ctrl = serial_port_in(port, SCSCR);
809 if (uart_circ_empty(xmit))
810 ctrl &= ~SCSCR_TIE;
811 else
812 ctrl |= SCSCR_TIE;
813 serial_port_out(port, SCSCR, ctrl);
814 return;
815 }
816
817 count = sci_txroom(port);
818
819 do {
820 unsigned char c;
821
822 if (port->x_char) {
823 c = port->x_char;
824 port->x_char = 0;
825 } else if (!uart_circ_empty(xmit) && !stopped) {
826 c = xmit->buf[xmit->tail];
827 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
828 } else {
829 break;
830 }
831
832 serial_port_out(port, SCxTDR, c);
833
834 port->icount.tx++;
835 } while (--count > 0);
836
837 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port));
838
839 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
840 uart_write_wakeup(port);
841 if (uart_circ_empty(xmit))
842 sci_stop_tx(port);
843
844}
845
846/* On SH3, SCIF may read end-of-break as a space->mark char */
847#define STEPFN(c) ({int __c = (c); (((__c-1)|(__c)) == -1); })
848
849static void sci_receive_chars(struct uart_port *port)
850{
851 struct tty_port *tport = &port->state->port;
852 int i, count, copied = 0;
853 unsigned short status;
854 unsigned char flag;
855
856 status = serial_port_in(port, SCxSR);
857 if (!(status & SCxSR_RDxF(port)))
858 return;
859
860 while (1) {
861 /* Don't copy more bytes than there is room for in the buffer */
862 count = tty_buffer_request_room(tport, sci_rxfill(port));
863
864 /* If for any reason we can't copy more data, we're done! */
865 if (count == 0)
866 break;
867
868 if (port->type == PORT_SCI) {
869 char c = serial_port_in(port, SCxRDR);
870 if (uart_handle_sysrq_char(port, c))
871 count = 0;
872 else
873 tty_insert_flip_char(tport, c, TTY_NORMAL);
874 } else {
875 for (i = 0; i < count; i++) {
876 char c = serial_port_in(port, SCxRDR);
877
878 status = serial_port_in(port, SCxSR);
879 if (uart_handle_sysrq_char(port, c)) {
880 count--; i--;
881 continue;
882 }
883
884 /* Store data and status */
885 if (status & SCxSR_FER(port)) {
886 flag = TTY_FRAME;
887 port->icount.frame++;
888 dev_notice(port->dev, "frame error\n");
889 } else if (status & SCxSR_PER(port)) {
890 flag = TTY_PARITY;
891 port->icount.parity++;
892 dev_notice(port->dev, "parity error\n");
893 } else
894 flag = TTY_NORMAL;
895
896 tty_insert_flip_char(tport, c, flag);
897 }
898 }
899
900 serial_port_in(port, SCxSR); /* dummy read */
901 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
902
903 copied += count;
904 port->icount.rx += count;
905 }
906
907 if (copied) {
908 /* Tell the rest of the system the news. New characters! */
909 tty_flip_buffer_push(tport);
910 } else {
911 /* TTY buffers full; read from RX reg to prevent lockup */
912 serial_port_in(port, SCxRDR);
913 serial_port_in(port, SCxSR); /* dummy read */
914 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
915 }
916}
917
918static int sci_handle_errors(struct uart_port *port)
919{
920 int copied = 0;
921 unsigned short status = serial_port_in(port, SCxSR);
922 struct tty_port *tport = &port->state->port;
923 struct sci_port *s = to_sci_port(port);
924
925 /* Handle overruns */
926 if (status & s->params->overrun_mask) {
927 port->icount.overrun++;
928
929 /* overrun error */
930 if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
931 copied++;
932
933 dev_notice(port->dev, "overrun error\n");
934 }
935
936 if (status & SCxSR_FER(port)) {
937 /* frame error */
938 port->icount.frame++;
939
940 if (tty_insert_flip_char(tport, 0, TTY_FRAME))
941 copied++;
942
943 dev_notice(port->dev, "frame error\n");
944 }
945
946 if (status & SCxSR_PER(port)) {
947 /* parity error */
948 port->icount.parity++;
949
950 if (tty_insert_flip_char(tport, 0, TTY_PARITY))
951 copied++;
952
953 dev_notice(port->dev, "parity error\n");
954 }
955
956 if (copied)
957 tty_flip_buffer_push(tport);
958
959 return copied;
960}
961
962static int sci_handle_fifo_overrun(struct uart_port *port)
963{
964 struct tty_port *tport = &port->state->port;
965 struct sci_port *s = to_sci_port(port);
966 const struct plat_sci_reg *reg;
967 int copied = 0;
968 u16 status;
969
970 reg = sci_getreg(port, s->params->overrun_reg);
971 if (!reg->size)
972 return 0;
973
974 status = serial_port_in(port, s->params->overrun_reg);
975 if (status & s->params->overrun_mask) {
976 status &= ~s->params->overrun_mask;
977 serial_port_out(port, s->params->overrun_reg, status);
978
979 port->icount.overrun++;
980
981 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
982 tty_flip_buffer_push(tport);
983
984 dev_dbg(port->dev, "overrun error\n");
985 copied++;
986 }
987
988 return copied;
989}
990
991static int sci_handle_breaks(struct uart_port *port)
992{
993 int copied = 0;
994 unsigned short status = serial_port_in(port, SCxSR);
995 struct tty_port *tport = &port->state->port;
996
997 if (uart_handle_break(port))
998 return 0;
999
1000 if (status & SCxSR_BRK(port)) {
1001 port->icount.brk++;
1002
1003 /* Notify of BREAK */
1004 if (tty_insert_flip_char(tport, 0, TTY_BREAK))
1005 copied++;
1006
1007 dev_dbg(port->dev, "BREAK detected\n");
1008 }
1009
1010 if (copied)
1011 tty_flip_buffer_push(tport);
1012
1013 copied += sci_handle_fifo_overrun(port);
1014
1015 return copied;
1016}
1017
1018static int scif_set_rtrg(struct uart_port *port, int rx_trig)
1019{
1020 unsigned int bits;
1021
1022 if (rx_trig < 1)
1023 rx_trig = 1;
1024 if (rx_trig >= port->fifosize)
1025 rx_trig = port->fifosize;
1026
1027 /* HSCIF can be set to an arbitrary level. */
1028 if (sci_getreg(port, HSRTRGR)->size) {
1029 serial_port_out(port, HSRTRGR, rx_trig);
1030 return rx_trig;
1031 }
1032
1033 switch (port->type) {
1034 case PORT_SCIF:
1035 if (rx_trig < 4) {
1036 bits = 0;
1037 rx_trig = 1;
1038 } else if (rx_trig < 8) {
1039 bits = SCFCR_RTRG0;
1040 rx_trig = 4;
1041 } else if (rx_trig < 14) {
1042 bits = SCFCR_RTRG1;
1043 rx_trig = 8;
1044 } else {
1045 bits = SCFCR_RTRG0 | SCFCR_RTRG1;
1046 rx_trig = 14;
1047 }
1048 break;
1049 case PORT_SCIFA:
1050 case PORT_SCIFB:
1051 if (rx_trig < 16) {
1052 bits = 0;
1053 rx_trig = 1;
1054 } else if (rx_trig < 32) {
1055 bits = SCFCR_RTRG0;
1056 rx_trig = 16;
1057 } else if (rx_trig < 48) {
1058 bits = SCFCR_RTRG1;
1059 rx_trig = 32;
1060 } else {
1061 bits = SCFCR_RTRG0 | SCFCR_RTRG1;
1062 rx_trig = 48;
1063 }
1064 break;
1065 default:
1066 WARN(1, "unknown FIFO configuration");
1067 return 1;
1068 }
1069
1070 serial_port_out(port, SCFCR,
1071 (serial_port_in(port, SCFCR) &
1072 ~(SCFCR_RTRG1 | SCFCR_RTRG0)) | bits);
1073
1074 return rx_trig;
1075}
1076
1077static int scif_rtrg_enabled(struct uart_port *port)
1078{
1079 if (sci_getreg(port, HSRTRGR)->size)
1080 return serial_port_in(port, HSRTRGR) != 0;
1081 else
1082 return (serial_port_in(port, SCFCR) &
1083 (SCFCR_RTRG0 | SCFCR_RTRG1)) != 0;
1084}
1085
1086static void rx_fifo_timer_fn(struct timer_list *t)
1087{
1088 struct sci_port *s = from_timer(s, t, rx_fifo_timer);
1089 struct uart_port *port = &s->port;
1090
1091 dev_dbg(port->dev, "Rx timed out\n");
1092 scif_set_rtrg(port, 1);
1093}
1094
1095static ssize_t rx_fifo_trigger_show(struct device *dev,
1096 struct device_attribute *attr, char *buf)
1097{
1098 struct uart_port *port = dev_get_drvdata(dev);
1099 struct sci_port *sci = to_sci_port(port);
1100
1101 return sprintf(buf, "%d\n", sci->rx_trigger);
1102}
1103
1104static ssize_t rx_fifo_trigger_store(struct device *dev,
1105 struct device_attribute *attr,
1106 const char *buf, size_t count)
1107{
1108 struct uart_port *port = dev_get_drvdata(dev);
1109 struct sci_port *sci = to_sci_port(port);
1110 int ret;
1111 long r;
1112
1113 ret = kstrtol(buf, 0, &r);
1114 if (ret)
1115 return ret;
1116
1117 sci->rx_trigger = scif_set_rtrg(port, r);
1118 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1119 scif_set_rtrg(port, 1);
1120
1121 return count;
1122}
1123
1124static DEVICE_ATTR_RW(rx_fifo_trigger);
1125
1126static ssize_t rx_fifo_timeout_show(struct device *dev,
1127 struct device_attribute *attr,
1128 char *buf)
1129{
1130 struct uart_port *port = dev_get_drvdata(dev);
1131 struct sci_port *sci = to_sci_port(port);
1132 int v;
1133
1134 if (port->type == PORT_HSCIF)
1135 v = sci->hscif_tot >> HSSCR_TOT_SHIFT;
1136 else
1137 v = sci->rx_fifo_timeout;
1138
1139 return sprintf(buf, "%d\n", v);
1140}
1141
1142static ssize_t rx_fifo_timeout_store(struct device *dev,
1143 struct device_attribute *attr,
1144 const char *buf,
1145 size_t count)
1146{
1147 struct uart_port *port = dev_get_drvdata(dev);
1148 struct sci_port *sci = to_sci_port(port);
1149 int ret;
1150 long r;
1151
1152 ret = kstrtol(buf, 0, &r);
1153 if (ret)
1154 return ret;
1155
1156 if (port->type == PORT_HSCIF) {
1157 if (r < 0 || r > 3)
1158 return -EINVAL;
1159 sci->hscif_tot = r << HSSCR_TOT_SHIFT;
1160 } else {
1161 sci->rx_fifo_timeout = r;
1162 scif_set_rtrg(port, 1);
1163 if (r > 0)
1164 timer_setup(&sci->rx_fifo_timer, rx_fifo_timer_fn, 0);
1165 }
1166
1167 return count;
1168}
1169
1170static DEVICE_ATTR_RW(rx_fifo_timeout);
1171
1172
1173#ifdef CONFIG_SERIAL_SH_SCI_DMA
1174static void sci_dma_tx_complete(void *arg)
1175{
1176 struct sci_port *s = arg;
1177 struct uart_port *port = &s->port;
1178 struct circ_buf *xmit = &port->state->xmit;
1179 unsigned long flags;
1180
1181 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1182
1183 spin_lock_irqsave(&port->lock, flags);
1184
1185 xmit->tail += s->tx_dma_len;
1186 xmit->tail &= UART_XMIT_SIZE - 1;
1187
1188 port->icount.tx += s->tx_dma_len;
1189
1190 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1191 uart_write_wakeup(port);
1192
1193 if (!uart_circ_empty(xmit)) {
1194 s->cookie_tx = 0;
1195 schedule_work(&s->work_tx);
1196 } else {
1197 s->cookie_tx = -EINVAL;
1198 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1199 u16 ctrl = serial_port_in(port, SCSCR);
1200 serial_port_out(port, SCSCR, ctrl & ~SCSCR_TIE);
1201 }
1202 }
1203
1204 spin_unlock_irqrestore(&port->lock, flags);
1205}
1206
1207/* Locking: called with port lock held */
1208static int sci_dma_rx_push(struct sci_port *s, void *buf, size_t count)
1209{
1210 struct uart_port *port = &s->port;
1211 struct tty_port *tport = &port->state->port;
1212 int copied;
1213
1214 copied = tty_insert_flip_string(tport, buf, count);
1215 if (copied < count)
1216 port->icount.buf_overrun++;
1217
1218 port->icount.rx += copied;
1219
1220 return copied;
1221}
1222
1223static int sci_dma_rx_find_active(struct sci_port *s)
1224{
1225 unsigned int i;
1226
1227 for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++)
1228 if (s->active_rx == s->cookie_rx[i])
1229 return i;
1230
1231 return -1;
1232}
1233
1234static void sci_dma_rx_chan_invalidate(struct sci_port *s)
1235{
1236 unsigned int i;
1237
1238 s->chan_rx = NULL;
1239 for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++)
1240 s->cookie_rx[i] = -EINVAL;
1241 s->active_rx = 0;
1242}
1243
1244static void sci_dma_rx_release(struct sci_port *s)
1245{
1246 struct dma_chan *chan = s->chan_rx_saved;
1247
1248 s->chan_rx_saved = NULL;
1249 sci_dma_rx_chan_invalidate(s);
1250 dmaengine_terminate_sync(chan);
1251 dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0],
1252 sg_dma_address(&s->sg_rx[0]));
1253 dma_release_channel(chan);
1254}
1255
1256static void start_hrtimer_us(struct hrtimer *hrt, unsigned long usec)
1257{
1258 long sec = usec / 1000000;
1259 long nsec = (usec % 1000000) * 1000;
1260 ktime_t t = ktime_set(sec, nsec);
1261
1262 hrtimer_start(hrt, t, HRTIMER_MODE_REL);
1263}
1264
1265static void sci_dma_rx_reenable_irq(struct sci_port *s)
1266{
1267 struct uart_port *port = &s->port;
1268 u16 scr;
1269
1270 /* Direct new serial port interrupts back to CPU */
1271 scr = serial_port_in(port, SCSCR);
1272 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1273 scr &= ~SCSCR_RDRQE;
1274 enable_irq(s->irqs[SCIx_RXI_IRQ]);
1275 }
1276 serial_port_out(port, SCSCR, scr | SCSCR_RIE);
1277}
1278
1279static void sci_dma_rx_complete(void *arg)
1280{
1281 struct sci_port *s = arg;
1282 struct dma_chan *chan = s->chan_rx;
1283 struct uart_port *port = &s->port;
1284 struct dma_async_tx_descriptor *desc;
1285 unsigned long flags;
1286 int active, count = 0;
1287
1288 dev_dbg(port->dev, "%s(%d) active cookie %d\n", __func__, port->line,
1289 s->active_rx);
1290
1291 spin_lock_irqsave(&port->lock, flags);
1292
1293 active = sci_dma_rx_find_active(s);
1294 if (active >= 0)
1295 count = sci_dma_rx_push(s, s->rx_buf[active], s->buf_len_rx);
1296
1297 start_hrtimer_us(&s->rx_timer, s->rx_timeout);
1298
1299 if (count)
1300 tty_flip_buffer_push(&port->state->port);
1301
1302 desc = dmaengine_prep_slave_sg(s->chan_rx, &s->sg_rx[active], 1,
1303 DMA_DEV_TO_MEM,
1304 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1305 if (!desc)
1306 goto fail;
1307
1308 desc->callback = sci_dma_rx_complete;
1309 desc->callback_param = s;
1310 s->cookie_rx[active] = dmaengine_submit(desc);
1311 if (dma_submit_error(s->cookie_rx[active]))
1312 goto fail;
1313
1314 s->active_rx = s->cookie_rx[!active];
1315
1316 dma_async_issue_pending(chan);
1317
1318 spin_unlock_irqrestore(&port->lock, flags);
1319 dev_dbg(port->dev, "%s: cookie %d #%d, new active cookie %d\n",
1320 __func__, s->cookie_rx[active], active, s->active_rx);
1321 return;
1322
1323fail:
1324 spin_unlock_irqrestore(&port->lock, flags);
1325 dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
1326 /* Switch to PIO */
1327 spin_lock_irqsave(&port->lock, flags);
1328 dmaengine_terminate_async(chan);
1329 sci_dma_rx_chan_invalidate(s);
1330 sci_dma_rx_reenable_irq(s);
1331 spin_unlock_irqrestore(&port->lock, flags);
1332}
1333
1334static void sci_dma_tx_release(struct sci_port *s)
1335{
1336 struct dma_chan *chan = s->chan_tx_saved;
1337
1338 cancel_work_sync(&s->work_tx);
1339 s->chan_tx_saved = s->chan_tx = NULL;
1340 s->cookie_tx = -EINVAL;
1341 dmaengine_terminate_sync(chan);
1342 dma_unmap_single(chan->device->dev, s->tx_dma_addr, UART_XMIT_SIZE,
1343 DMA_TO_DEVICE);
1344 dma_release_channel(chan);
1345}
1346
1347static int sci_dma_rx_submit(struct sci_port *s, bool port_lock_held)
1348{
1349 struct dma_chan *chan = s->chan_rx;
1350 struct uart_port *port = &s->port;
1351 unsigned long flags;
1352 int i;
1353
1354 for (i = 0; i < 2; i++) {
1355 struct scatterlist *sg = &s->sg_rx[i];
1356 struct dma_async_tx_descriptor *desc;
1357
1358 desc = dmaengine_prep_slave_sg(chan,
1359 sg, 1, DMA_DEV_TO_MEM,
1360 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1361 if (!desc)
1362 goto fail;
1363
1364 desc->callback = sci_dma_rx_complete;
1365 desc->callback_param = s;
1366 s->cookie_rx[i] = dmaengine_submit(desc);
1367 if (dma_submit_error(s->cookie_rx[i]))
1368 goto fail;
1369
1370 }
1371
1372 s->active_rx = s->cookie_rx[0];
1373
1374 dma_async_issue_pending(chan);
1375 return 0;
1376
1377fail:
1378 /* Switch to PIO */
1379 if (!port_lock_held)
1380 spin_lock_irqsave(&port->lock, flags);
1381 if (i)
1382 dmaengine_terminate_async(chan);
1383 sci_dma_rx_chan_invalidate(s);
1384 sci_start_rx(port);
1385 if (!port_lock_held)
1386 spin_unlock_irqrestore(&port->lock, flags);
1387 return -EAGAIN;
1388}
1389
1390static void sci_dma_tx_work_fn(struct work_struct *work)
1391{
1392 struct sci_port *s = container_of(work, struct sci_port, work_tx);
1393 struct dma_async_tx_descriptor *desc;
1394 struct dma_chan *chan = s->chan_tx;
1395 struct uart_port *port = &s->port;
1396 struct circ_buf *xmit = &port->state->xmit;
1397 unsigned long flags;
1398 dma_addr_t buf;
1399 int head, tail;
1400
1401 /*
1402 * DMA is idle now.
1403 * Port xmit buffer is already mapped, and it is one page... Just adjust
1404 * offsets and lengths. Since it is a circular buffer, we have to
1405 * transmit till the end, and then the rest. Take the port lock to get a
1406 * consistent xmit buffer state.
1407 */
1408 spin_lock_irq(&port->lock);
1409 head = xmit->head;
1410 tail = xmit->tail;
1411 buf = s->tx_dma_addr + (tail & (UART_XMIT_SIZE - 1));
1412 s->tx_dma_len = min_t(unsigned int,
1413 CIRC_CNT(head, tail, UART_XMIT_SIZE),
1414 CIRC_CNT_TO_END(head, tail, UART_XMIT_SIZE));
1415 if (!s->tx_dma_len) {
1416 /* Transmit buffer has been flushed */
1417 spin_unlock_irq(&port->lock);
1418 return;
1419 }
1420
1421 desc = dmaengine_prep_slave_single(chan, buf, s->tx_dma_len,
1422 DMA_MEM_TO_DEV,
1423 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1424 if (!desc) {
1425 spin_unlock_irq(&port->lock);
1426 dev_warn(port->dev, "Failed preparing Tx DMA descriptor\n");
1427 goto switch_to_pio;
1428 }
1429
1430 dma_sync_single_for_device(chan->device->dev, buf, s->tx_dma_len,
1431 DMA_TO_DEVICE);
1432
1433 desc->callback = sci_dma_tx_complete;
1434 desc->callback_param = s;
1435 s->cookie_tx = dmaengine_submit(desc);
1436 if (dma_submit_error(s->cookie_tx)) {
1437 spin_unlock_irq(&port->lock);
1438 dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n");
1439 goto switch_to_pio;
1440 }
1441
1442 spin_unlock_irq(&port->lock);
1443 dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n",
1444 __func__, xmit->buf, tail, head, s->cookie_tx);
1445
1446 dma_async_issue_pending(chan);
1447 return;
1448
1449switch_to_pio:
1450 spin_lock_irqsave(&port->lock, flags);
1451 s->chan_tx = NULL;
1452 sci_start_tx(port);
1453 spin_unlock_irqrestore(&port->lock, flags);
1454 return;
1455}
1456
1457static enum hrtimer_restart sci_dma_rx_timer_fn(struct hrtimer *t)
1458{
1459 struct sci_port *s = container_of(t, struct sci_port, rx_timer);
1460 struct dma_chan *chan = s->chan_rx;
1461 struct uart_port *port = &s->port;
1462 struct dma_tx_state state;
1463 enum dma_status status;
1464 unsigned long flags;
1465 unsigned int read;
1466 int active, count;
1467
1468 dev_dbg(port->dev, "DMA Rx timed out\n");
1469
1470 spin_lock_irqsave(&port->lock, flags);
1471
1472 active = sci_dma_rx_find_active(s);
1473 if (active < 0) {
1474 spin_unlock_irqrestore(&port->lock, flags);
1475 return HRTIMER_NORESTART;
1476 }
1477
1478 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state);
1479 if (status == DMA_COMPLETE) {
1480 spin_unlock_irqrestore(&port->lock, flags);
1481 dev_dbg(port->dev, "Cookie %d #%d has already completed\n",
1482 s->active_rx, active);
1483
1484 /* Let packet complete handler take care of the packet */
1485 return HRTIMER_NORESTART;
1486 }
1487
1488 dmaengine_pause(chan);
1489
1490 /*
1491 * sometimes DMA transfer doesn't stop even if it is stopped and
1492 * data keeps on coming until transaction is complete so check
1493 * for DMA_COMPLETE again
1494 * Let packet complete handler take care of the packet
1495 */
1496 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state);
1497 if (status == DMA_COMPLETE) {
1498 spin_unlock_irqrestore(&port->lock, flags);
1499 dev_dbg(port->dev, "Transaction complete after DMA engine was stopped");
1500 return HRTIMER_NORESTART;
1501 }
1502
1503 /* Handle incomplete DMA receive */
1504 dmaengine_terminate_async(s->chan_rx);
1505 read = sg_dma_len(&s->sg_rx[active]) - state.residue;
1506
1507 if (read) {
1508 count = sci_dma_rx_push(s, s->rx_buf[active], read);
1509 if (count)
1510 tty_flip_buffer_push(&port->state->port);
1511 }
1512
1513 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1514 sci_dma_rx_submit(s, true);
1515
1516 sci_dma_rx_reenable_irq(s);
1517
1518 spin_unlock_irqrestore(&port->lock, flags);
1519
1520 return HRTIMER_NORESTART;
1521}
1522
1523static struct dma_chan *sci_request_dma_chan(struct uart_port *port,
1524 enum dma_transfer_direction dir)
1525{
1526 struct dma_chan *chan;
1527 struct dma_slave_config cfg;
1528 int ret;
1529
1530 chan = dma_request_slave_channel(port->dev,
1531 dir == DMA_MEM_TO_DEV ? "tx" : "rx");
1532 if (!chan) {
1533 dev_dbg(port->dev, "dma_request_slave_channel failed\n");
1534 return NULL;
1535 }
1536
1537 memset(&cfg, 0, sizeof(cfg));
1538 cfg.direction = dir;
1539 if (dir == DMA_MEM_TO_DEV) {
1540 cfg.dst_addr = port->mapbase +
1541 (sci_getreg(port, SCxTDR)->offset << port->regshift);
1542 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1543 } else {
1544 cfg.src_addr = port->mapbase +
1545 (sci_getreg(port, SCxRDR)->offset << port->regshift);
1546 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1547 }
1548
1549 ret = dmaengine_slave_config(chan, &cfg);
1550 if (ret) {
1551 dev_warn(port->dev, "dmaengine_slave_config failed %d\n", ret);
1552 dma_release_channel(chan);
1553 return NULL;
1554 }
1555
1556 return chan;
1557}
1558
1559static void sci_request_dma(struct uart_port *port)
1560{
1561 struct sci_port *s = to_sci_port(port);
1562 struct dma_chan *chan;
1563
1564 dev_dbg(port->dev, "%s: port %d\n", __func__, port->line);
1565
1566 /*
1567 * DMA on console may interfere with Kernel log messages which use
1568 * plain putchar(). So, simply don't use it with a console.
1569 */
1570 if (uart_console(port))
1571 return;
1572
1573 if (!port->dev->of_node)
1574 return;
1575
1576 s->cookie_tx = -EINVAL;
1577
1578 /*
1579 * Don't request a dma channel if no channel was specified
1580 * in the device tree.
1581 */
1582 if (!of_find_property(port->dev->of_node, "dmas", NULL))
1583 return;
1584
1585 chan = sci_request_dma_chan(port, DMA_MEM_TO_DEV);
1586 dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan);
1587 if (chan) {
1588 /* UART circular tx buffer is an aligned page. */
1589 s->tx_dma_addr = dma_map_single(chan->device->dev,
1590 port->state->xmit.buf,
1591 UART_XMIT_SIZE,
1592 DMA_TO_DEVICE);
1593 if (dma_mapping_error(chan->device->dev, s->tx_dma_addr)) {
1594 dev_warn(port->dev, "Failed mapping Tx DMA descriptor\n");
1595 dma_release_channel(chan);
1596 } else {
1597 dev_dbg(port->dev, "%s: mapped %lu@%p to %pad\n",
1598 __func__, UART_XMIT_SIZE,
1599 port->state->xmit.buf, &s->tx_dma_addr);
1600
1601 INIT_WORK(&s->work_tx, sci_dma_tx_work_fn);
1602 s->chan_tx_saved = s->chan_tx = chan;
1603 }
1604 }
1605
1606 chan = sci_request_dma_chan(port, DMA_DEV_TO_MEM);
1607 dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan);
1608 if (chan) {
1609 unsigned int i;
1610 dma_addr_t dma;
1611 void *buf;
1612
1613 s->buf_len_rx = 2 * max_t(size_t, 16, port->fifosize);
1614 buf = dma_alloc_coherent(chan->device->dev, s->buf_len_rx * 2,
1615 &dma, GFP_KERNEL);
1616 if (!buf) {
1617 dev_warn(port->dev,
1618 "Failed to allocate Rx dma buffer, using PIO\n");
1619 dma_release_channel(chan);
1620 return;
1621 }
1622
1623 for (i = 0; i < 2; i++) {
1624 struct scatterlist *sg = &s->sg_rx[i];
1625
1626 sg_init_table(sg, 1);
1627 s->rx_buf[i] = buf;
1628 sg_dma_address(sg) = dma;
1629 sg_dma_len(sg) = s->buf_len_rx;
1630
1631 buf += s->buf_len_rx;
1632 dma += s->buf_len_rx;
1633 }
1634
1635 hrtimer_init(&s->rx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
1636 s->rx_timer.function = sci_dma_rx_timer_fn;
1637
1638 s->chan_rx_saved = s->chan_rx = chan;
1639
1640 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1641 sci_dma_rx_submit(s, false);
1642 }
1643}
1644
1645static void sci_free_dma(struct uart_port *port)
1646{
1647 struct sci_port *s = to_sci_port(port);
1648
1649 if (s->chan_tx_saved)
1650 sci_dma_tx_release(s);
1651 if (s->chan_rx_saved)
1652 sci_dma_rx_release(s);
1653}
1654
1655static void sci_flush_buffer(struct uart_port *port)
1656{
1657 struct sci_port *s = to_sci_port(port);
1658
1659 /*
1660 * In uart_flush_buffer(), the xmit circular buffer has just been
1661 * cleared, so we have to reset tx_dma_len accordingly, and stop any
1662 * pending transfers
1663 */
1664 s->tx_dma_len = 0;
1665 if (s->chan_tx) {
1666 dmaengine_terminate_async(s->chan_tx);
1667 s->cookie_tx = -EINVAL;
1668 }
1669}
1670#else /* !CONFIG_SERIAL_SH_SCI_DMA */
1671static inline void sci_request_dma(struct uart_port *port)
1672{
1673}
1674
1675static inline void sci_free_dma(struct uart_port *port)
1676{
1677}
1678
1679#define sci_flush_buffer NULL
1680#endif /* !CONFIG_SERIAL_SH_SCI_DMA */
1681
1682static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
1683{
1684 struct uart_port *port = ptr;
1685 struct sci_port *s = to_sci_port(port);
1686
1687#ifdef CONFIG_SERIAL_SH_SCI_DMA
1688 if (s->chan_rx) {
1689 u16 scr = serial_port_in(port, SCSCR);
1690 u16 ssr = serial_port_in(port, SCxSR);
1691
1692 /* Disable future Rx interrupts */
1693 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1694 disable_irq_nosync(irq);
1695 scr |= SCSCR_RDRQE;
1696 } else {
1697 if (sci_dma_rx_submit(s, false) < 0)
1698 goto handle_pio;
1699
1700 scr &= ~SCSCR_RIE;
1701 }
1702 serial_port_out(port, SCSCR, scr);
1703 /* Clear current interrupt */
1704 serial_port_out(port, SCxSR,
1705 ssr & ~(SCIF_DR | SCxSR_RDxF(port)));
1706 dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u us\n",
1707 jiffies, s->rx_timeout);
1708 start_hrtimer_us(&s->rx_timer, s->rx_timeout);
1709
1710 return IRQ_HANDLED;
1711 }
1712
1713handle_pio:
1714#endif
1715
1716 if (s->rx_trigger > 1 && s->rx_fifo_timeout > 0) {
1717 if (!scif_rtrg_enabled(port))
1718 scif_set_rtrg(port, s->rx_trigger);
1719
1720 mod_timer(&s->rx_fifo_timer, jiffies + DIV_ROUND_UP(
1721 s->rx_frame * HZ * s->rx_fifo_timeout, 1000000));
1722 }
1723
1724 /* I think sci_receive_chars has to be called irrespective
1725 * of whether the I_IXOFF is set, otherwise, how is the interrupt
1726 * to be disabled?
1727 */
1728 sci_receive_chars(port);
1729
1730 return IRQ_HANDLED;
1731}
1732
1733static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
1734{
1735 struct uart_port *port = ptr;
1736 unsigned long flags;
1737
1738 spin_lock_irqsave(&port->lock, flags);
1739 sci_transmit_chars(port);
1740 spin_unlock_irqrestore(&port->lock, flags);
1741
1742 return IRQ_HANDLED;
1743}
1744
1745static irqreturn_t sci_br_interrupt(int irq, void *ptr)
1746{
1747 struct uart_port *port = ptr;
1748
1749 /* Handle BREAKs */
1750 sci_handle_breaks(port);
1751 sci_clear_SCxSR(port, SCxSR_BREAK_CLEAR(port));
1752
1753 return IRQ_HANDLED;
1754}
1755
1756static irqreturn_t sci_er_interrupt(int irq, void *ptr)
1757{
1758 struct uart_port *port = ptr;
1759 struct sci_port *s = to_sci_port(port);
1760
1761 if (s->irqs[SCIx_ERI_IRQ] == s->irqs[SCIx_BRI_IRQ]) {
1762 /* Break and Error interrupts are muxed */
1763 unsigned short ssr_status = serial_port_in(port, SCxSR);
1764
1765 /* Break Interrupt */
1766 if (ssr_status & SCxSR_BRK(port))
1767 sci_br_interrupt(irq, ptr);
1768
1769 /* Break only? */
1770 if (!(ssr_status & SCxSR_ERRORS(port)))
1771 return IRQ_HANDLED;
1772 }
1773
1774 /* Handle errors */
1775 if (port->type == PORT_SCI) {
1776 if (sci_handle_errors(port)) {
1777 /* discard character in rx buffer */
1778 serial_port_in(port, SCxSR);
1779 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
1780 }
1781 } else {
1782 sci_handle_fifo_overrun(port);
1783 if (!s->chan_rx)
1784 sci_receive_chars(port);
1785 }
1786
1787 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port));
1788
1789 /* Kick the transmission */
1790 if (!s->chan_tx)
1791 sci_tx_interrupt(irq, ptr);
1792
1793 return IRQ_HANDLED;
1794}
1795
1796static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
1797{
1798 unsigned short ssr_status, scr_status, err_enabled, orer_status = 0;
1799 struct uart_port *port = ptr;
1800 struct sci_port *s = to_sci_port(port);
1801 irqreturn_t ret = IRQ_NONE;
1802
1803 ssr_status = serial_port_in(port, SCxSR);
1804 scr_status = serial_port_in(port, SCSCR);
1805 if (s->params->overrun_reg == SCxSR)
1806 orer_status = ssr_status;
1807 else if (sci_getreg(port, s->params->overrun_reg)->size)
1808 orer_status = serial_port_in(port, s->params->overrun_reg);
1809
1810 err_enabled = scr_status & port_rx_irq_mask(port);
1811
1812 /* Tx Interrupt */
1813 if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) &&
1814 !s->chan_tx)
1815 ret = sci_tx_interrupt(irq, ptr);
1816
1817 /*
1818 * Rx Interrupt: if we're using DMA, the DMA controller clears RDF /
1819 * DR flags
1820 */
1821 if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) &&
1822 (scr_status & SCSCR_RIE))
1823 ret = sci_rx_interrupt(irq, ptr);
1824
1825 /* Error Interrupt */
1826 if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled)
1827 ret = sci_er_interrupt(irq, ptr);
1828
1829 /* Break Interrupt */
1830 if ((ssr_status & SCxSR_BRK(port)) && err_enabled)
1831 ret = sci_br_interrupt(irq, ptr);
1832
1833 /* Overrun Interrupt */
1834 if (orer_status & s->params->overrun_mask) {
1835 sci_handle_fifo_overrun(port);
1836 ret = IRQ_HANDLED;
1837 }
1838
1839 return ret;
1840}
1841
1842static const struct sci_irq_desc {
1843 const char *desc;
1844 irq_handler_t handler;
1845} sci_irq_desc[] = {
1846 /*
1847 * Split out handlers, the default case.
1848 */
1849 [SCIx_ERI_IRQ] = {
1850 .desc = "rx err",
1851 .handler = sci_er_interrupt,
1852 },
1853
1854 [SCIx_RXI_IRQ] = {
1855 .desc = "rx full",
1856 .handler = sci_rx_interrupt,
1857 },
1858
1859 [SCIx_TXI_IRQ] = {
1860 .desc = "tx empty",
1861 .handler = sci_tx_interrupt,
1862 },
1863
1864 [SCIx_BRI_IRQ] = {
1865 .desc = "break",
1866 .handler = sci_br_interrupt,
1867 },
1868
1869 [SCIx_DRI_IRQ] = {
1870 .desc = "rx ready",
1871 .handler = sci_rx_interrupt,
1872 },
1873
1874 [SCIx_TEI_IRQ] = {
1875 .desc = "tx end",
1876 .handler = sci_tx_interrupt,
1877 },
1878
1879 /*
1880 * Special muxed handler.
1881 */
1882 [SCIx_MUX_IRQ] = {
1883 .desc = "mux",
1884 .handler = sci_mpxed_interrupt,
1885 },
1886};
1887
1888static int sci_request_irq(struct sci_port *port)
1889{
1890 struct uart_port *up = &port->port;
1891 int i, j, w, ret = 0;
1892
1893 for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
1894 const struct sci_irq_desc *desc;
1895 int irq;
1896
1897 /* Check if already registered (muxed) */
1898 for (w = 0; w < i; w++)
1899 if (port->irqs[w] == port->irqs[i])
1900 w = i + 1;
1901 if (w > i)
1902 continue;
1903
1904 if (SCIx_IRQ_IS_MUXED(port)) {
1905 i = SCIx_MUX_IRQ;
1906 irq = up->irq;
1907 } else {
1908 irq = port->irqs[i];
1909
1910 /*
1911 * Certain port types won't support all of the
1912 * available interrupt sources.
1913 */
1914 if (unlikely(irq < 0))
1915 continue;
1916 }
1917
1918 desc = sci_irq_desc + i;
1919 port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
1920 dev_name(up->dev), desc->desc);
1921 if (!port->irqstr[j]) {
1922 ret = -ENOMEM;
1923 goto out_nomem;
1924 }
1925
1926 ret = request_irq(irq, desc->handler, up->irqflags,
1927 port->irqstr[j], port);
1928 if (unlikely(ret)) {
1929 dev_err(up->dev, "Can't allocate %s IRQ\n", desc->desc);
1930 goto out_noirq;
1931 }
1932 }
1933
1934 return 0;
1935
1936out_noirq:
1937 while (--i >= 0)
1938 free_irq(port->irqs[i], port);
1939
1940out_nomem:
1941 while (--j >= 0)
1942 kfree(port->irqstr[j]);
1943
1944 return ret;
1945}
1946
1947static void sci_free_irq(struct sci_port *port)
1948{
1949 int i, j;
1950
1951 /*
1952 * Intentionally in reverse order so we iterate over the muxed
1953 * IRQ first.
1954 */
1955 for (i = 0; i < SCIx_NR_IRQS; i++) {
1956 int irq = port->irqs[i];
1957
1958 /*
1959 * Certain port types won't support all of the available
1960 * interrupt sources.
1961 */
1962 if (unlikely(irq < 0))
1963 continue;
1964
1965 /* Check if already freed (irq was muxed) */
1966 for (j = 0; j < i; j++)
1967 if (port->irqs[j] == irq)
1968 j = i + 1;
1969 if (j > i)
1970 continue;
1971
1972 free_irq(port->irqs[i], port);
1973 kfree(port->irqstr[i]);
1974
1975 if (SCIx_IRQ_IS_MUXED(port)) {
1976 /* If there's only one IRQ, we're done. */
1977 return;
1978 }
1979 }
1980}
1981
1982static unsigned int sci_tx_empty(struct uart_port *port)
1983{
1984 unsigned short status = serial_port_in(port, SCxSR);
1985 unsigned short in_tx_fifo = sci_txfill(port);
1986
1987 return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
1988}
1989
1990static void sci_set_rts(struct uart_port *port, bool state)
1991{
1992 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1993 u16 data = serial_port_in(port, SCPDR);
1994
1995 /* Active low */
1996 if (state)
1997 data &= ~SCPDR_RTSD;
1998 else
1999 data |= SCPDR_RTSD;
2000 serial_port_out(port, SCPDR, data);
2001
2002 /* RTS# is output */
2003 serial_port_out(port, SCPCR,
2004 serial_port_in(port, SCPCR) | SCPCR_RTSC);
2005 } else if (sci_getreg(port, SCSPTR)->size) {
2006 u16 ctrl = serial_port_in(port, SCSPTR);
2007
2008 /* Active low */
2009 if (state)
2010 ctrl &= ~SCSPTR_RTSDT;
2011 else
2012 ctrl |= SCSPTR_RTSDT;
2013 serial_port_out(port, SCSPTR, ctrl);
2014 }
2015}
2016
2017static bool sci_get_cts(struct uart_port *port)
2018{
2019 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
2020 /* Active low */
2021 return !(serial_port_in(port, SCPDR) & SCPDR_CTSD);
2022 } else if (sci_getreg(port, SCSPTR)->size) {
2023 /* Active low */
2024 return !(serial_port_in(port, SCSPTR) & SCSPTR_CTSDT);
2025 }
2026
2027 return true;
2028}
2029
2030/*
2031 * Modem control is a bit of a mixed bag for SCI(F) ports. Generally
2032 * CTS/RTS is supported in hardware by at least one port and controlled
2033 * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently
2034 * handled via the ->init_pins() op, which is a bit of a one-way street,
2035 * lacking any ability to defer pin control -- this will later be
2036 * converted over to the GPIO framework).
2037 *
2038 * Other modes (such as loopback) are supported generically on certain
2039 * port types, but not others. For these it's sufficient to test for the
2040 * existence of the support register and simply ignore the port type.
2041 */
2042static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
2043{
2044 struct sci_port *s = to_sci_port(port);
2045
2046 if (mctrl & TIOCM_LOOP) {
2047 const struct plat_sci_reg *reg;
2048
2049 /*
2050 * Standard loopback mode for SCFCR ports.
2051 */
2052 reg = sci_getreg(port, SCFCR);
2053 if (reg->size)
2054 serial_port_out(port, SCFCR,
2055 serial_port_in(port, SCFCR) |
2056 SCFCR_LOOP);
2057 }
2058
2059 mctrl_gpio_set(s->gpios, mctrl);
2060
2061 if (!s->has_rtscts)
2062 return;
2063
2064 if (!(mctrl & TIOCM_RTS)) {
2065 /* Disable Auto RTS */
2066 serial_port_out(port, SCFCR,
2067 serial_port_in(port, SCFCR) & ~SCFCR_MCE);
2068
2069 /* Clear RTS */
2070 sci_set_rts(port, 0);
2071 } else if (s->autorts) {
2072 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
2073 /* Enable RTS# pin function */
2074 serial_port_out(port, SCPCR,
2075 serial_port_in(port, SCPCR) & ~SCPCR_RTSC);
2076 }
2077
2078 /* Enable Auto RTS */
2079 serial_port_out(port, SCFCR,
2080 serial_port_in(port, SCFCR) | SCFCR_MCE);
2081 } else {
2082 /* Set RTS */
2083 sci_set_rts(port, 1);
2084 }
2085}
2086
2087static unsigned int sci_get_mctrl(struct uart_port *port)
2088{
2089 struct sci_port *s = to_sci_port(port);
2090 struct mctrl_gpios *gpios = s->gpios;
2091 unsigned int mctrl = 0;
2092
2093 mctrl_gpio_get(gpios, &mctrl);
2094
2095 /*
2096 * CTS/RTS is handled in hardware when supported, while nothing
2097 * else is wired up.
2098 */
2099 if (s->autorts) {
2100 if (sci_get_cts(port))
2101 mctrl |= TIOCM_CTS;
2102 } else if (!mctrl_gpio_to_gpiod(gpios, UART_GPIO_CTS)) {
2103 mctrl |= TIOCM_CTS;
2104 }
2105 if (!mctrl_gpio_to_gpiod(gpios, UART_GPIO_DSR))
2106 mctrl |= TIOCM_DSR;
2107 if (!mctrl_gpio_to_gpiod(gpios, UART_GPIO_DCD))
2108 mctrl |= TIOCM_CAR;
2109
2110 return mctrl;
2111}
2112
2113static void sci_enable_ms(struct uart_port *port)
2114{
2115 mctrl_gpio_enable_ms(to_sci_port(port)->gpios);
2116}
2117
2118static void sci_break_ctl(struct uart_port *port, int break_state)
2119{
2120 unsigned short scscr, scsptr;
2121 unsigned long flags;
2122
2123 /* check wheter the port has SCSPTR */
2124 if (!sci_getreg(port, SCSPTR)->size) {
2125 /*
2126 * Not supported by hardware. Most parts couple break and rx
2127 * interrupts together, with break detection always enabled.
2128 */
2129 return;
2130 }
2131
2132 spin_lock_irqsave(&port->lock, flags);
2133 scsptr = serial_port_in(port, SCSPTR);
2134 scscr = serial_port_in(port, SCSCR);
2135
2136 if (break_state == -1) {
2137 scsptr = (scsptr | SCSPTR_SPB2IO) & ~SCSPTR_SPB2DT;
2138 scscr &= ~SCSCR_TE;
2139 } else {
2140 scsptr = (scsptr | SCSPTR_SPB2DT) & ~SCSPTR_SPB2IO;
2141 scscr |= SCSCR_TE;
2142 }
2143
2144 serial_port_out(port, SCSPTR, scsptr);
2145 serial_port_out(port, SCSCR, scscr);
2146 spin_unlock_irqrestore(&port->lock, flags);
2147}
2148
2149static int sci_startup(struct uart_port *port)
2150{
2151 struct sci_port *s = to_sci_port(port);
2152 int ret;
2153
2154 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
2155
2156 sci_request_dma(port);
2157
2158 ret = sci_request_irq(s);
2159 if (unlikely(ret < 0)) {
2160 sci_free_dma(port);
2161 return ret;
2162 }
2163
2164 return 0;
2165}
2166
2167static void sci_shutdown(struct uart_port *port)
2168{
2169 struct sci_port *s = to_sci_port(port);
2170 unsigned long flags;
2171 u16 scr;
2172
2173 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
2174
2175 s->autorts = false;
2176 mctrl_gpio_disable_ms(to_sci_port(port)->gpios);
2177
2178 spin_lock_irqsave(&port->lock, flags);
2179 sci_stop_rx(port);
2180 sci_stop_tx(port);
2181 /*
2182 * Stop RX and TX, disable related interrupts, keep clock source
2183 * and HSCIF TOT bits
2184 */
2185 scr = serial_port_in(port, SCSCR);
2186 serial_port_out(port, SCSCR, scr &
2187 (SCSCR_CKE1 | SCSCR_CKE0 | s->hscif_tot));
2188 spin_unlock_irqrestore(&port->lock, flags);
2189
2190#ifdef CONFIG_SERIAL_SH_SCI_DMA
2191 if (s->chan_rx_saved) {
2192 dev_dbg(port->dev, "%s(%d) deleting rx_timer\n", __func__,
2193 port->line);
2194 hrtimer_cancel(&s->rx_timer);
2195 }
2196#endif
2197
2198 if (s->rx_trigger > 1 && s->rx_fifo_timeout > 0)
2199 del_timer_sync(&s->rx_fifo_timer);
2200 sci_free_irq(s);
2201 sci_free_dma(port);
2202}
2203
2204static int sci_sck_calc(struct sci_port *s, unsigned int bps,
2205 unsigned int *srr)
2206{
2207 unsigned long freq = s->clk_rates[SCI_SCK];
2208 int err, min_err = INT_MAX;
2209 unsigned int sr;
2210
2211 if (s->port.type != PORT_HSCIF)
2212 freq *= 2;
2213
2214 for_each_sr(sr, s) {
2215 err = DIV_ROUND_CLOSEST(freq, sr) - bps;
2216 if (abs(err) >= abs(min_err))
2217 continue;
2218
2219 min_err = err;
2220 *srr = sr - 1;
2221
2222 if (!err)
2223 break;
2224 }
2225
2226 dev_dbg(s->port.dev, "SCK: %u%+d bps using SR %u\n", bps, min_err,
2227 *srr + 1);
2228 return min_err;
2229}
2230
2231static int sci_brg_calc(struct sci_port *s, unsigned int bps,
2232 unsigned long freq, unsigned int *dlr,
2233 unsigned int *srr)
2234{
2235 int err, min_err = INT_MAX;
2236 unsigned int sr, dl;
2237
2238 if (s->port.type != PORT_HSCIF)
2239 freq *= 2;
2240
2241 for_each_sr(sr, s) {
2242 dl = DIV_ROUND_CLOSEST(freq, sr * bps);
2243 dl = clamp(dl, 1U, 65535U);
2244
2245 err = DIV_ROUND_CLOSEST(freq, sr * dl) - bps;
2246 if (abs(err) >= abs(min_err))
2247 continue;
2248
2249 min_err = err;
2250 *dlr = dl;
2251 *srr = sr - 1;
2252
2253 if (!err)
2254 break;
2255 }
2256
2257 dev_dbg(s->port.dev, "BRG: %u%+d bps using DL %u SR %u\n", bps,
2258 min_err, *dlr, *srr + 1);
2259 return min_err;
2260}
2261
2262/* calculate sample rate, BRR, and clock select */
2263static int sci_scbrr_calc(struct sci_port *s, unsigned int bps,
2264 unsigned int *brr, unsigned int *srr,
2265 unsigned int *cks)
2266{
2267 unsigned long freq = s->clk_rates[SCI_FCK];
2268 unsigned int sr, br, prediv, scrate, c;
2269 int err, min_err = INT_MAX;
2270
2271 if (s->port.type != PORT_HSCIF)
2272 freq *= 2;
2273
2274 /*
2275 * Find the combination of sample rate and clock select with the
2276 * smallest deviation from the desired baud rate.
2277 * Prefer high sample rates to maximise the receive margin.
2278 *
2279 * M: Receive margin (%)
2280 * N: Ratio of bit rate to clock (N = sampling rate)
2281 * D: Clock duty (D = 0 to 1.0)
2282 * L: Frame length (L = 9 to 12)
2283 * F: Absolute value of clock frequency deviation
2284 *
2285 * M = |(0.5 - 1 / 2 * N) - ((L - 0.5) * F) -
2286 * (|D - 0.5| / N * (1 + F))|
2287 * NOTE: Usually, treat D for 0.5, F is 0 by this calculation.
2288 */
2289 for_each_sr(sr, s) {
2290 for (c = 0; c <= 3; c++) {
2291 /* integerized formulas from HSCIF documentation */
2292 prediv = sr * (1 << (2 * c + 1));
2293
2294 /*
2295 * We need to calculate:
2296 *
2297 * br = freq / (prediv * bps) clamped to [1..256]
2298 * err = freq / (br * prediv) - bps
2299 *
2300 * Watch out for overflow when calculating the desired
2301 * sampling clock rate!
2302 */
2303 if (bps > UINT_MAX / prediv)
2304 break;
2305
2306 scrate = prediv * bps;
2307 br = DIV_ROUND_CLOSEST(freq, scrate);
2308 br = clamp(br, 1U, 256U);
2309
2310 err = DIV_ROUND_CLOSEST(freq, br * prediv) - bps;
2311 if (abs(err) >= abs(min_err))
2312 continue;
2313
2314 min_err = err;
2315 *brr = br - 1;
2316 *srr = sr - 1;
2317 *cks = c;
2318
2319 if (!err)
2320 goto found;
2321 }
2322 }
2323
2324found:
2325 dev_dbg(s->port.dev, "BRR: %u%+d bps using N %u SR %u cks %u\n", bps,
2326 min_err, *brr, *srr + 1, *cks);
2327 return min_err;
2328}
2329
2330static void sci_reset(struct uart_port *port)
2331{
2332 const struct plat_sci_reg *reg;
2333 unsigned int status;
2334 struct sci_port *s = to_sci_port(port);
2335
2336 serial_port_out(port, SCSCR, s->hscif_tot); /* TE=0, RE=0, CKE1=0 */
2337
2338 reg = sci_getreg(port, SCFCR);
2339 if (reg->size)
2340 serial_port_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
2341
2342 sci_clear_SCxSR(port,
2343 SCxSR_RDxF_CLEAR(port) & SCxSR_ERROR_CLEAR(port) &
2344 SCxSR_BREAK_CLEAR(port));
2345 if (sci_getreg(port, SCLSR)->size) {
2346 status = serial_port_in(port, SCLSR);
2347 status &= ~(SCLSR_TO | SCLSR_ORER);
2348 serial_port_out(port, SCLSR, status);
2349 }
2350
2351 if (s->rx_trigger > 1) {
2352 if (s->rx_fifo_timeout) {
2353 scif_set_rtrg(port, 1);
2354 timer_setup(&s->rx_fifo_timer, rx_fifo_timer_fn, 0);
2355 } else {
2356 if (port->type == PORT_SCIFA ||
2357 port->type == PORT_SCIFB)
2358 scif_set_rtrg(port, 1);
2359 else
2360 scif_set_rtrg(port, s->rx_trigger);
2361 }
2362 }
2363}
2364
2365static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
2366 struct ktermios *old)
2367{
2368 unsigned int baud, smr_val = SCSMR_ASYNC, scr_val = 0, i, bits;
2369 unsigned int brr = 255, cks = 0, srr = 15, dl = 0, sccks = 0;
2370 unsigned int brr1 = 255, cks1 = 0, srr1 = 15, dl1 = 0;
2371 struct sci_port *s = to_sci_port(port);
2372 const struct plat_sci_reg *reg;
2373 int min_err = INT_MAX, err;
2374 unsigned long max_freq = 0;
2375 int best_clk = -1;
2376 unsigned long flags;
2377
2378 if ((termios->c_cflag & CSIZE) == CS7)
2379 smr_val |= SCSMR_CHR;
2380 if (termios->c_cflag & PARENB)
2381 smr_val |= SCSMR_PE;
2382 if (termios->c_cflag & PARODD)
2383 smr_val |= SCSMR_PE | SCSMR_ODD;
2384 if (termios->c_cflag & CSTOPB)
2385 smr_val |= SCSMR_STOP;
2386
2387 /*
2388 * earlyprintk comes here early on with port->uartclk set to zero.
2389 * the clock framework is not up and running at this point so here
2390 * we assume that 115200 is the maximum baud rate. please note that
2391 * the baud rate is not programmed during earlyprintk - it is assumed
2392 * that the previous boot loader has enabled required clocks and
2393 * setup the baud rate generator hardware for us already.
2394 */
2395 if (!port->uartclk) {
2396 baud = uart_get_baud_rate(port, termios, old, 0, 115200);
2397 goto done;
2398 }
2399
2400 for (i = 0; i < SCI_NUM_CLKS; i++)
2401 max_freq = max(max_freq, s->clk_rates[i]);
2402
2403 baud = uart_get_baud_rate(port, termios, old, 0, max_freq / min_sr(s));
2404 if (!baud)
2405 goto done;
2406
2407 /*
2408 * There can be multiple sources for the sampling clock. Find the one
2409 * that gives us the smallest deviation from the desired baud rate.
2410 */
2411
2412 /* Optional Undivided External Clock */
2413 if (s->clk_rates[SCI_SCK] && port->type != PORT_SCIFA &&
2414 port->type != PORT_SCIFB) {
2415 err = sci_sck_calc(s, baud, &srr1);
2416 if (abs(err) < abs(min_err)) {
2417 best_clk = SCI_SCK;
2418 scr_val = SCSCR_CKE1;
2419 sccks = SCCKS_CKS;
2420 min_err = err;
2421 srr = srr1;
2422 if (!err)
2423 goto done;
2424 }
2425 }
2426
2427 /* Optional BRG Frequency Divided External Clock */
2428 if (s->clk_rates[SCI_SCIF_CLK] && sci_getreg(port, SCDL)->size) {
2429 err = sci_brg_calc(s, baud, s->clk_rates[SCI_SCIF_CLK], &dl1,
2430 &srr1);
2431 if (abs(err) < abs(min_err)) {
2432 best_clk = SCI_SCIF_CLK;
2433 scr_val = SCSCR_CKE1;
2434 sccks = 0;
2435 min_err = err;
2436 dl = dl1;
2437 srr = srr1;
2438 if (!err)
2439 goto done;
2440 }
2441 }
2442
2443 /* Optional BRG Frequency Divided Internal Clock */
2444 if (s->clk_rates[SCI_BRG_INT] && sci_getreg(port, SCDL)->size) {
2445 err = sci_brg_calc(s, baud, s->clk_rates[SCI_BRG_INT], &dl1,
2446 &srr1);
2447 if (abs(err) < abs(min_err)) {
2448 best_clk = SCI_BRG_INT;
2449 scr_val = SCSCR_CKE1;
2450 sccks = SCCKS_XIN;
2451 min_err = err;
2452 dl = dl1;
2453 srr = srr1;
2454 if (!min_err)
2455 goto done;
2456 }
2457 }
2458
2459 /* Divided Functional Clock using standard Bit Rate Register */
2460 err = sci_scbrr_calc(s, baud, &brr1, &srr1, &cks1);
2461 if (abs(err) < abs(min_err)) {
2462 best_clk = SCI_FCK;
2463 scr_val = 0;
2464 min_err = err;
2465 brr = brr1;
2466 srr = srr1;
2467 cks = cks1;
2468 }
2469
2470done:
2471 if (best_clk >= 0)
2472 dev_dbg(port->dev, "Using clk %pC for %u%+d bps\n",
2473 s->clks[best_clk], baud, min_err);
2474
2475 sci_port_enable(s);
2476
2477 /*
2478 * Program the optional External Baud Rate Generator (BRG) first.
2479 * It controls the mux to select (H)SCK or frequency divided clock.
2480 */
2481 if (best_clk >= 0 && sci_getreg(port, SCCKS)->size) {
2482 serial_port_out(port, SCDL, dl);
2483 serial_port_out(port, SCCKS, sccks);
2484 }
2485
2486 spin_lock_irqsave(&port->lock, flags);
2487
2488 sci_reset(port);
2489
2490 uart_update_timeout(port, termios->c_cflag, baud);
2491
2492 /* byte size and parity */
2493 switch (termios->c_cflag & CSIZE) {
2494 case CS5:
2495 bits = 7;
2496 break;
2497 case CS6:
2498 bits = 8;
2499 break;
2500 case CS7:
2501 bits = 9;
2502 break;
2503 default:
2504 bits = 10;
2505 break;
2506 }
2507
2508 if (termios->c_cflag & CSTOPB)
2509 bits++;
2510 if (termios->c_cflag & PARENB)
2511 bits++;
2512
2513 if (best_clk >= 0) {
2514 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
2515 switch (srr + 1) {
2516 case 5: smr_val |= SCSMR_SRC_5; break;
2517 case 7: smr_val |= SCSMR_SRC_7; break;
2518 case 11: smr_val |= SCSMR_SRC_11; break;
2519 case 13: smr_val |= SCSMR_SRC_13; break;
2520 case 16: smr_val |= SCSMR_SRC_16; break;
2521 case 17: smr_val |= SCSMR_SRC_17; break;
2522 case 19: smr_val |= SCSMR_SRC_19; break;
2523 case 27: smr_val |= SCSMR_SRC_27; break;
2524 }
2525 smr_val |= cks;
2526 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
2527 serial_port_out(port, SCSMR, smr_val);
2528 serial_port_out(port, SCBRR, brr);
2529 if (sci_getreg(port, HSSRR)->size) {
2530 unsigned int hssrr = srr | HSCIF_SRE;
2531 /* Calculate deviation from intended rate at the
2532 * center of the last stop bit in sampling clocks.
2533 */
2534 int last_stop = bits * 2 - 1;
2535 int deviation = DIV_ROUND_CLOSEST(min_err * last_stop *
2536 (int)(srr + 1),
2537 2 * (int)baud);
2538
2539 if (abs(deviation) >= 2) {
2540 /* At least two sampling clocks off at the
2541 * last stop bit; we can increase the error
2542 * margin by shifting the sampling point.
2543 */
2544 int shift = clamp(deviation / 2, -8, 7);
2545
2546 hssrr |= (shift << HSCIF_SRHP_SHIFT) &
2547 HSCIF_SRHP_MASK;
2548 hssrr |= HSCIF_SRDE;
2549 }
2550 serial_port_out(port, HSSRR, hssrr);
2551 }
2552
2553 /* Wait one bit interval */
2554 udelay((1000000 + (baud - 1)) / baud);
2555 } else {
2556 /* Don't touch the bit rate configuration */
2557 scr_val = s->cfg->scscr & (SCSCR_CKE1 | SCSCR_CKE0);
2558 smr_val |= serial_port_in(port, SCSMR) &
2559 (SCSMR_CKEDG | SCSMR_SRC_MASK | SCSMR_CKS);
2560 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
2561 serial_port_out(port, SCSMR, smr_val);
2562 }
2563
2564 sci_init_pins(port, termios->c_cflag);
2565
2566 port->status &= ~UPSTAT_AUTOCTS;
2567 s->autorts = false;
2568 reg = sci_getreg(port, SCFCR);
2569 if (reg->size) {
2570 unsigned short ctrl = serial_port_in(port, SCFCR);
2571
2572 if ((port->flags & UPF_HARD_FLOW) &&
2573 (termios->c_cflag & CRTSCTS)) {
2574 /* There is no CTS interrupt to restart the hardware */
2575 port->status |= UPSTAT_AUTOCTS;
2576 /* MCE is enabled when RTS is raised */
2577 s->autorts = true;
2578 }
2579
2580 /*
2581 * As we've done a sci_reset() above, ensure we don't
2582 * interfere with the FIFOs while toggling MCE. As the
2583 * reset values could still be set, simply mask them out.
2584 */
2585 ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST);
2586
2587 serial_port_out(port, SCFCR, ctrl);
2588 }
2589 if (port->flags & UPF_HARD_FLOW) {
2590 /* Refresh (Auto) RTS */
2591 sci_set_mctrl(port, port->mctrl);
2592 }
2593
2594 scr_val |= SCSCR_RE | SCSCR_TE |
2595 (s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0));
2596 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
2597 if ((srr + 1 == 5) &&
2598 (port->type == PORT_SCIFA || port->type == PORT_SCIFB)) {
2599 /*
2600 * In asynchronous mode, when the sampling rate is 1/5, first
2601 * received data may become invalid on some SCIFA and SCIFB.
2602 * To avoid this problem wait more than 1 serial data time (1
2603 * bit time x serial data number) after setting SCSCR.RE = 1.
2604 */
2605 udelay(DIV_ROUND_UP(10 * 1000000, baud));
2606 }
2607
2608 /*
2609 * Calculate delay for 2 DMA buffers (4 FIFO).
2610 * See serial_core.c::uart_update_timeout().
2611 * With 10 bits (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above
2612 * function calculates 1 jiffie for the data plus 5 jiffies for the
2613 * "slop(e)." Then below we calculate 5 jiffies (20ms) for 2 DMA
2614 * buffers (4 FIFO sizes), but when performing a faster transfer, the
2615 * value obtained by this formula is too small. Therefore, if the value
2616 * is smaller than 20ms, use 20ms as the timeout value for DMA.
2617 */
2618 s->rx_frame = (10000 * bits) / (baud / 100);
2619#ifdef CONFIG_SERIAL_SH_SCI_DMA
2620 s->rx_timeout = s->buf_len_rx * 2 * s->rx_frame;
2621 if (s->rx_timeout < 20)
2622 s->rx_timeout = 20;
2623#endif
2624
2625 if ((termios->c_cflag & CREAD) != 0)
2626 sci_start_rx(port);
2627
2628 spin_unlock_irqrestore(&port->lock, flags);
2629
2630 sci_port_disable(s);
2631
2632 if (UART_ENABLE_MS(port, termios->c_cflag))
2633 sci_enable_ms(port);
2634}
2635
2636static void sci_pm(struct uart_port *port, unsigned int state,
2637 unsigned int oldstate)
2638{
2639 struct sci_port *sci_port = to_sci_port(port);
2640
2641 switch (state) {
2642 case UART_PM_STATE_OFF:
2643 sci_port_disable(sci_port);
2644 break;
2645 default:
2646 sci_port_enable(sci_port);
2647 break;
2648 }
2649}
2650
2651static const char *sci_type(struct uart_port *port)
2652{
2653 switch (port->type) {
2654 case PORT_IRDA:
2655 return "irda";
2656 case PORT_SCI:
2657 return "sci";
2658 case PORT_SCIF:
2659 return "scif";
2660 case PORT_SCIFA:
2661 return "scifa";
2662 case PORT_SCIFB:
2663 return "scifb";
2664 case PORT_HSCIF:
2665 return "hscif";
2666 }
2667
2668 return NULL;
2669}
2670
2671static int sci_remap_port(struct uart_port *port)
2672{
2673 struct sci_port *sport = to_sci_port(port);
2674
2675 /*
2676 * Nothing to do if there's already an established membase.
2677 */
2678 if (port->membase)
2679 return 0;
2680
2681 if (port->dev->of_node || (port->flags & UPF_IOREMAP)) {
2682 port->membase = ioremap_nocache(port->mapbase, sport->reg_size);
2683 if (unlikely(!port->membase)) {
2684 dev_err(port->dev, "can't remap port#%d\n", port->line);
2685 return -ENXIO;
2686 }
2687 } else {
2688 /*
2689 * For the simple (and majority of) cases where we don't
2690 * need to do any remapping, just cast the cookie
2691 * directly.
2692 */
2693 port->membase = (void __iomem *)(uintptr_t)port->mapbase;
2694 }
2695
2696 return 0;
2697}
2698
2699static void sci_release_port(struct uart_port *port)
2700{
2701 struct sci_port *sport = to_sci_port(port);
2702
2703 if (port->dev->of_node || (port->flags & UPF_IOREMAP)) {
2704 iounmap(port->membase);
2705 port->membase = NULL;
2706 }
2707
2708 release_mem_region(port->mapbase, sport->reg_size);
2709}
2710
2711static int sci_request_port(struct uart_port *port)
2712{
2713 struct resource *res;
2714 struct sci_port *sport = to_sci_port(port);
2715 int ret;
2716
2717 res = request_mem_region(port->mapbase, sport->reg_size,
2718 dev_name(port->dev));
2719 if (unlikely(res == NULL)) {
2720 dev_err(port->dev, "request_mem_region failed.");
2721 return -EBUSY;
2722 }
2723
2724 ret = sci_remap_port(port);
2725 if (unlikely(ret != 0)) {
2726 release_resource(res);
2727 return ret;
2728 }
2729
2730 return 0;
2731}
2732
2733static void sci_config_port(struct uart_port *port, int flags)
2734{
2735 if (flags & UART_CONFIG_TYPE) {
2736 struct sci_port *sport = to_sci_port(port);
2737
2738 port->type = sport->cfg->type;
2739 sci_request_port(port);
2740 }
2741}
2742
2743static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
2744{
2745 if (ser->baud_base < 2400)
2746 /* No paper tape reader for Mitch.. */
2747 return -EINVAL;
2748
2749 return 0;
2750}
2751
2752static const struct uart_ops sci_uart_ops = {
2753 .tx_empty = sci_tx_empty,
2754 .set_mctrl = sci_set_mctrl,
2755 .get_mctrl = sci_get_mctrl,
2756 .start_tx = sci_start_tx,
2757 .stop_tx = sci_stop_tx,
2758 .stop_rx = sci_stop_rx,
2759 .enable_ms = sci_enable_ms,
2760 .break_ctl = sci_break_ctl,
2761 .startup = sci_startup,
2762 .shutdown = sci_shutdown,
2763 .flush_buffer = sci_flush_buffer,
2764 .set_termios = sci_set_termios,
2765 .pm = sci_pm,
2766 .type = sci_type,
2767 .release_port = sci_release_port,
2768 .request_port = sci_request_port,
2769 .config_port = sci_config_port,
2770 .verify_port = sci_verify_port,
2771#ifdef CONFIG_CONSOLE_POLL
2772 .poll_get_char = sci_poll_get_char,
2773 .poll_put_char = sci_poll_put_char,
2774#endif
2775};
2776
2777static int sci_init_clocks(struct sci_port *sci_port, struct device *dev)
2778{
2779 const char *clk_names[] = {
2780 [SCI_FCK] = "fck",
2781 [SCI_SCK] = "sck",
2782 [SCI_BRG_INT] = "brg_int",
2783 [SCI_SCIF_CLK] = "scif_clk",
2784 };
2785 struct clk *clk;
2786 unsigned int i;
2787
2788 if (sci_port->cfg->type == PORT_HSCIF)
2789 clk_names[SCI_SCK] = "hsck";
2790
2791 for (i = 0; i < SCI_NUM_CLKS; i++) {
2792 clk = devm_clk_get(dev, clk_names[i]);
2793 if (PTR_ERR(clk) == -EPROBE_DEFER)
2794 return -EPROBE_DEFER;
2795
2796 if (IS_ERR(clk) && i == SCI_FCK) {
2797 /*
2798 * "fck" used to be called "sci_ick", and we need to
2799 * maintain DT backward compatibility.
2800 */
2801 clk = devm_clk_get(dev, "sci_ick");
2802 if (PTR_ERR(clk) == -EPROBE_DEFER)
2803 return -EPROBE_DEFER;
2804
2805 if (!IS_ERR(clk))
2806 goto found;
2807
2808 /*
2809 * Not all SH platforms declare a clock lookup entry
2810 * for SCI devices, in which case we need to get the
2811 * global "peripheral_clk" clock.
2812 */
2813 clk = devm_clk_get(dev, "peripheral_clk");
2814 if (!IS_ERR(clk))
2815 goto found;
2816
2817 dev_err(dev, "failed to get %s (%ld)\n", clk_names[i],
2818 PTR_ERR(clk));
2819 return PTR_ERR(clk);
2820 }
2821
2822found:
2823 if (IS_ERR(clk))
2824 dev_dbg(dev, "failed to get %s (%ld)\n", clk_names[i],
2825 PTR_ERR(clk));
2826 else
2827 dev_dbg(dev, "clk %s is %pC rate %lu\n", clk_names[i],
2828 clk, clk_get_rate(clk));
2829 sci_port->clks[i] = IS_ERR(clk) ? NULL : clk;
2830 }
2831 return 0;
2832}
2833
2834static const struct sci_port_params *
2835sci_probe_regmap(const struct plat_sci_port *cfg)
2836{
2837 unsigned int regtype;
2838
2839 if (cfg->regtype != SCIx_PROBE_REGTYPE)
2840 return &sci_port_params[cfg->regtype];
2841
2842 switch (cfg->type) {
2843 case PORT_SCI:
2844 regtype = SCIx_SCI_REGTYPE;
2845 break;
2846 case PORT_IRDA:
2847 regtype = SCIx_IRDA_REGTYPE;
2848 break;
2849 case PORT_SCIFA:
2850 regtype = SCIx_SCIFA_REGTYPE;
2851 break;
2852 case PORT_SCIFB:
2853 regtype = SCIx_SCIFB_REGTYPE;
2854 break;
2855 case PORT_SCIF:
2856 /*
2857 * The SH-4 is a bit of a misnomer here, although that's
2858 * where this particular port layout originated. This
2859 * configuration (or some slight variation thereof)
2860 * remains the dominant model for all SCIFs.
2861 */
2862 regtype = SCIx_SH4_SCIF_REGTYPE;
2863 break;
2864 case PORT_HSCIF:
2865 regtype = SCIx_HSCIF_REGTYPE;
2866 break;
2867 default:
2868 pr_err("Can't probe register map for given port\n");
2869 return NULL;
2870 }
2871
2872 return &sci_port_params[regtype];
2873}
2874
2875static int sci_init_single(struct platform_device *dev,
2876 struct sci_port *sci_port, unsigned int index,
2877 const struct plat_sci_port *p, bool early)
2878{
2879 struct uart_port *port = &sci_port->port;
2880 const struct resource *res;
2881 unsigned int i;
2882 int ret;
2883
2884 sci_port->cfg = p;
2885
2886 port->ops = &sci_uart_ops;
2887 port->iotype = UPIO_MEM;
2888 port->line = index;
2889
2890 res = platform_get_resource(dev, IORESOURCE_MEM, 0);
2891 if (res == NULL)
2892 return -ENOMEM;
2893
2894 port->mapbase = res->start;
2895 sci_port->reg_size = resource_size(res);
2896
2897 for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i) {
2898 if (i)
2899 sci_port->irqs[i] = platform_get_irq_optional(dev, i);
2900 else
2901 sci_port->irqs[i] = platform_get_irq(dev, i);
2902 }
2903
2904 /* The SCI generates several interrupts. They can be muxed together or
2905 * connected to different interrupt lines. In the muxed case only one
2906 * interrupt resource is specified as there is only one interrupt ID.
2907 * In the non-muxed case, up to 6 interrupt signals might be generated
2908 * from the SCI, however those signals might have their own individual
2909 * interrupt ID numbers, or muxed together with another interrupt.
2910 */
2911 if (sci_port->irqs[0] < 0)
2912 return -ENXIO;
2913
2914 if (sci_port->irqs[1] < 0)
2915 for (i = 1; i < ARRAY_SIZE(sci_port->irqs); i++)
2916 sci_port->irqs[i] = sci_port->irqs[0];
2917
2918 sci_port->params = sci_probe_regmap(p);
2919 if (unlikely(sci_port->params == NULL))
2920 return -EINVAL;
2921
2922 switch (p->type) {
2923 case PORT_SCIFB:
2924 sci_port->rx_trigger = 48;
2925 break;
2926 case PORT_HSCIF:
2927 sci_port->rx_trigger = 64;
2928 break;
2929 case PORT_SCIFA:
2930 sci_port->rx_trigger = 32;
2931 break;
2932 case PORT_SCIF:
2933 if (p->regtype == SCIx_SH7705_SCIF_REGTYPE)
2934 /* RX triggering not implemented for this IP */
2935 sci_port->rx_trigger = 1;
2936 else
2937 sci_port->rx_trigger = 8;
2938 break;
2939 default:
2940 sci_port->rx_trigger = 1;
2941 break;
2942 }
2943
2944 sci_port->rx_fifo_timeout = 0;
2945 sci_port->hscif_tot = 0;
2946
2947 /* SCIFA on sh7723 and sh7724 need a custom sampling rate that doesn't
2948 * match the SoC datasheet, this should be investigated. Let platform
2949 * data override the sampling rate for now.
2950 */
2951 sci_port->sampling_rate_mask = p->sampling_rate
2952 ? SCI_SR(p->sampling_rate)
2953 : sci_port->params->sampling_rate_mask;
2954
2955 if (!early) {
2956 ret = sci_init_clocks(sci_port, &dev->dev);
2957 if (ret < 0)
2958 return ret;
2959
2960 port->dev = &dev->dev;
2961
2962 pm_runtime_enable(&dev->dev);
2963 }
2964
2965 port->type = p->type;
2966 port->flags = UPF_FIXED_PORT | UPF_BOOT_AUTOCONF | p->flags;
2967 port->fifosize = sci_port->params->fifosize;
2968
2969 if (port->type == PORT_SCI) {
2970 if (sci_port->reg_size >= 0x20)
2971 port->regshift = 2;
2972 else
2973 port->regshift = 1;
2974 }
2975
2976 /*
2977 * The UART port needs an IRQ value, so we peg this to the RX IRQ
2978 * for the multi-IRQ ports, which is where we are primarily
2979 * concerned with the shutdown path synchronization.
2980 *
2981 * For the muxed case there's nothing more to do.
2982 */
2983 port->irq = sci_port->irqs[SCIx_RXI_IRQ];
2984 port->irqflags = 0;
2985
2986 port->serial_in = sci_serial_in;
2987 port->serial_out = sci_serial_out;
2988
2989 return 0;
2990}
2991
2992static void sci_cleanup_single(struct sci_port *port)
2993{
2994 pm_runtime_disable(port->port.dev);
2995}
2996
2997#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \
2998 defined(CONFIG_SERIAL_SH_SCI_EARLYCON)
2999static void serial_console_putchar(struct uart_port *port, int ch)
3000{
3001 sci_poll_put_char(port, ch);
3002}
3003
3004/*
3005 * Print a string to the serial port trying not to disturb
3006 * any possible real use of the port...
3007 */
3008static void serial_console_write(struct console *co, const char *s,
3009 unsigned count)
3010{
3011 struct sci_port *sci_port = &sci_ports[co->index];
3012 struct uart_port *port = &sci_port->port;
3013 unsigned short bits, ctrl, ctrl_temp;
3014 unsigned long flags;
3015 int locked = 1;
3016
3017#if defined(SUPPORT_SYSRQ)
3018 if (port->sysrq)
3019 locked = 0;
3020 else
3021#endif
3022 if (oops_in_progress)
3023 locked = spin_trylock_irqsave(&port->lock, flags);
3024 else
3025 spin_lock_irqsave(&port->lock, flags);
3026
3027 /* first save SCSCR then disable interrupts, keep clock source */
3028 ctrl = serial_port_in(port, SCSCR);
3029 ctrl_temp = SCSCR_RE | SCSCR_TE |
3030 (sci_port->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0)) |
3031 (ctrl & (SCSCR_CKE1 | SCSCR_CKE0));
3032 serial_port_out(port, SCSCR, ctrl_temp | sci_port->hscif_tot);
3033
3034 uart_console_write(port, s, count, serial_console_putchar);
3035
3036 /* wait until fifo is empty and last bit has been transmitted */
3037 bits = SCxSR_TDxE(port) | SCxSR_TEND(port);
3038 while ((serial_port_in(port, SCxSR) & bits) != bits)
3039 cpu_relax();
3040
3041 /* restore the SCSCR */
3042 serial_port_out(port, SCSCR, ctrl);
3043
3044 if (locked)
3045 spin_unlock_irqrestore(&port->lock, flags);
3046}
3047
3048static int serial_console_setup(struct console *co, char *options)
3049{
3050 struct sci_port *sci_port;
3051 struct uart_port *port;
3052 int baud = 115200;
3053 int bits = 8;
3054 int parity = 'n';
3055 int flow = 'n';
3056 int ret;
3057
3058 /*
3059 * Refuse to handle any bogus ports.
3060 */
3061 if (co->index < 0 || co->index >= SCI_NPORTS)
3062 return -ENODEV;
3063
3064 sci_port = &sci_ports[co->index];
3065 port = &sci_port->port;
3066
3067 /*
3068 * Refuse to handle uninitialized ports.
3069 */
3070 if (!port->ops)
3071 return -ENODEV;
3072
3073 ret = sci_remap_port(port);
3074 if (unlikely(ret != 0))
3075 return ret;
3076
3077 if (options)
3078 uart_parse_options(options, &baud, &parity, &bits, &flow);
3079
3080 return uart_set_options(port, co, baud, parity, bits, flow);
3081}
3082
3083static struct console serial_console = {
3084 .name = "ttySC",
3085 .device = uart_console_device,
3086 .write = serial_console_write,
3087 .setup = serial_console_setup,
3088 .flags = CON_PRINTBUFFER,
3089 .index = -1,
3090 .data = &sci_uart_driver,
3091};
3092
3093static struct console early_serial_console = {
3094 .name = "early_ttySC",
3095 .write = serial_console_write,
3096 .flags = CON_PRINTBUFFER,
3097 .index = -1,
3098};
3099
3100static char early_serial_buf[32];
3101
3102static int sci_probe_earlyprintk(struct platform_device *pdev)
3103{
3104 const struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev);
3105
3106 if (early_serial_console.data)
3107 return -EEXIST;
3108
3109 early_serial_console.index = pdev->id;
3110
3111 sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true);
3112
3113 serial_console_setup(&early_serial_console, early_serial_buf);
3114
3115 if (!strstr(early_serial_buf, "keep"))
3116 early_serial_console.flags |= CON_BOOT;
3117
3118 register_console(&early_serial_console);
3119 return 0;
3120}
3121
3122#define SCI_CONSOLE (&serial_console)
3123
3124#else
3125static inline int sci_probe_earlyprintk(struct platform_device *pdev)
3126{
3127 return -EINVAL;
3128}
3129
3130#define SCI_CONSOLE NULL
3131
3132#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE || CONFIG_SERIAL_SH_SCI_EARLYCON */
3133
3134static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized";
3135
3136static DEFINE_MUTEX(sci_uart_registration_lock);
3137static struct uart_driver sci_uart_driver = {
3138 .owner = THIS_MODULE,
3139 .driver_name = "sci",
3140 .dev_name = "ttySC",
3141 .major = SCI_MAJOR,
3142 .minor = SCI_MINOR_START,
3143 .nr = SCI_NPORTS,
3144 .cons = SCI_CONSOLE,
3145};
3146
3147static int sci_remove(struct platform_device *dev)
3148{
3149 struct sci_port *port = platform_get_drvdata(dev);
3150 unsigned int type = port->port.type; /* uart_remove_... clears it */
3151
3152 sci_ports_in_use &= ~BIT(port->port.line);
3153 uart_remove_one_port(&sci_uart_driver, &port->port);
3154
3155 sci_cleanup_single(port);
3156
3157 if (port->port.fifosize > 1)
3158 device_remove_file(&dev->dev, &dev_attr_rx_fifo_trigger);
3159 if (type == PORT_SCIFA || type == PORT_SCIFB || type == PORT_HSCIF)
3160 device_remove_file(&dev->dev, &dev_attr_rx_fifo_timeout);
3161
3162 return 0;
3163}
3164
3165
3166#define SCI_OF_DATA(type, regtype) (void *)((type) << 16 | (regtype))
3167#define SCI_OF_TYPE(data) ((unsigned long)(data) >> 16)
3168#define SCI_OF_REGTYPE(data) ((unsigned long)(data) & 0xffff)
3169
3170static const struct of_device_id of_sci_match[] = {
3171 /* SoC-specific types */
3172 {
3173 .compatible = "renesas,scif-r7s72100",
3174 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH2_SCIF_FIFODATA_REGTYPE),
3175 },
3176 {
3177 .compatible = "renesas,scif-r7s9210",
3178 .data = SCI_OF_DATA(PORT_SCIF, SCIx_RZ_SCIFA_REGTYPE),
3179 },
3180 /* Family-specific types */
3181 {
3182 .compatible = "renesas,rcar-gen1-scif",
3183 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
3184 }, {
3185 .compatible = "renesas,rcar-gen2-scif",
3186 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
3187 }, {
3188 .compatible = "renesas,rcar-gen3-scif",
3189 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
3190 },
3191 /* Generic types */
3192 {
3193 .compatible = "renesas,scif",
3194 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_REGTYPE),
3195 }, {
3196 .compatible = "renesas,scifa",
3197 .data = SCI_OF_DATA(PORT_SCIFA, SCIx_SCIFA_REGTYPE),
3198 }, {
3199 .compatible = "renesas,scifb",
3200 .data = SCI_OF_DATA(PORT_SCIFB, SCIx_SCIFB_REGTYPE),
3201 }, {
3202 .compatible = "renesas,hscif",
3203 .data = SCI_OF_DATA(PORT_HSCIF, SCIx_HSCIF_REGTYPE),
3204 }, {
3205 .compatible = "renesas,sci",
3206 .data = SCI_OF_DATA(PORT_SCI, SCIx_SCI_REGTYPE),
3207 }, {
3208 /* Terminator */
3209 },
3210};
3211MODULE_DEVICE_TABLE(of, of_sci_match);
3212
3213static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev,
3214 unsigned int *dev_id)
3215{
3216 struct device_node *np = pdev->dev.of_node;
3217 struct plat_sci_port *p;
3218 struct sci_port *sp;
3219 const void *data;
3220 int id;
3221
3222 if (!IS_ENABLED(CONFIG_OF) || !np)
3223 return NULL;
3224
3225 data = of_device_get_match_data(&pdev->dev);
3226
3227 p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
3228 if (!p)
3229 return NULL;
3230
3231 /* Get the line number from the aliases node. */
3232 id = of_alias_get_id(np, "serial");
3233 if (id < 0 && ~sci_ports_in_use)
3234 id = ffz(sci_ports_in_use);
3235 if (id < 0) {
3236 dev_err(&pdev->dev, "failed to get alias id (%d)\n", id);
3237 return NULL;
3238 }
3239 if (id >= ARRAY_SIZE(sci_ports)) {
3240 dev_err(&pdev->dev, "serial%d out of range\n", id);
3241 return NULL;
3242 }
3243
3244 sp = &sci_ports[id];
3245 *dev_id = id;
3246
3247 p->type = SCI_OF_TYPE(data);
3248 p->regtype = SCI_OF_REGTYPE(data);
3249
3250 sp->has_rtscts = of_property_read_bool(np, "uart-has-rtscts");
3251
3252 return p;
3253}
3254
3255static int sci_probe_single(struct platform_device *dev,
3256 unsigned int index,
3257 struct plat_sci_port *p,
3258 struct sci_port *sciport)
3259{
3260 int ret;
3261
3262 /* Sanity check */
3263 if (unlikely(index >= SCI_NPORTS)) {
3264 dev_notice(&dev->dev, "Attempting to register port %d when only %d are available\n",
3265 index+1, SCI_NPORTS);
3266 dev_notice(&dev->dev, "Consider bumping CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
3267 return -EINVAL;
3268 }
3269 BUILD_BUG_ON(SCI_NPORTS > sizeof(sci_ports_in_use) * 8);
3270 if (sci_ports_in_use & BIT(index))
3271 return -EBUSY;
3272
3273 mutex_lock(&sci_uart_registration_lock);
3274 if (!sci_uart_driver.state) {
3275 ret = uart_register_driver(&sci_uart_driver);
3276 if (ret) {
3277 mutex_unlock(&sci_uart_registration_lock);
3278 return ret;
3279 }
3280 }
3281 mutex_unlock(&sci_uart_registration_lock);
3282
3283 ret = sci_init_single(dev, sciport, index, p, false);
3284 if (ret)
3285 return ret;
3286
3287 sciport->gpios = mctrl_gpio_init(&sciport->port, 0);
3288 if (IS_ERR(sciport->gpios))
3289 return PTR_ERR(sciport->gpios);
3290
3291 if (sciport->has_rtscts) {
3292 if (mctrl_gpio_to_gpiod(sciport->gpios, UART_GPIO_CTS) ||
3293 mctrl_gpio_to_gpiod(sciport->gpios, UART_GPIO_RTS)) {
3294 dev_err(&dev->dev, "Conflicting RTS/CTS config\n");
3295 return -EINVAL;
3296 }
3297 sciport->port.flags |= UPF_HARD_FLOW;
3298 }
3299
3300 ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
3301 if (ret) {
3302 sci_cleanup_single(sciport);
3303 return ret;
3304 }
3305
3306 return 0;
3307}
3308
3309static int sci_probe(struct platform_device *dev)
3310{
3311 struct plat_sci_port *p;
3312 struct sci_port *sp;
3313 unsigned int dev_id;
3314 int ret;
3315
3316 /*
3317 * If we've come here via earlyprintk initialization, head off to
3318 * the special early probe. We don't have sufficient device state
3319 * to make it beyond this yet.
3320 */
3321 if (is_early_platform_device(dev))
3322 return sci_probe_earlyprintk(dev);
3323
3324 if (dev->dev.of_node) {
3325 p = sci_parse_dt(dev, &dev_id);
3326 if (p == NULL)
3327 return -EINVAL;
3328 } else {
3329 p = dev->dev.platform_data;
3330 if (p == NULL) {
3331 dev_err(&dev->dev, "no platform data supplied\n");
3332 return -EINVAL;
3333 }
3334
3335 dev_id = dev->id;
3336 }
3337
3338 sp = &sci_ports[dev_id];
3339 platform_set_drvdata(dev, sp);
3340
3341 ret = sci_probe_single(dev, dev_id, p, sp);
3342 if (ret)
3343 return ret;
3344
3345 if (sp->port.fifosize > 1) {
3346 ret = device_create_file(&dev->dev, &dev_attr_rx_fifo_trigger);
3347 if (ret)
3348 return ret;
3349 }
3350 if (sp->port.type == PORT_SCIFA || sp->port.type == PORT_SCIFB ||
3351 sp->port.type == PORT_HSCIF) {
3352 ret = device_create_file(&dev->dev, &dev_attr_rx_fifo_timeout);
3353 if (ret) {
3354 if (sp->port.fifosize > 1) {
3355 device_remove_file(&dev->dev,
3356 &dev_attr_rx_fifo_trigger);
3357 }
3358 return ret;
3359 }
3360 }
3361
3362#ifdef CONFIG_SH_STANDARD_BIOS
3363 sh_bios_gdb_detach();
3364#endif
3365
3366 sci_ports_in_use |= BIT(dev_id);
3367 return 0;
3368}
3369
3370static __maybe_unused int sci_suspend(struct device *dev)
3371{
3372 struct sci_port *sport = dev_get_drvdata(dev);
3373
3374 if (sport)
3375 uart_suspend_port(&sci_uart_driver, &sport->port);
3376
3377 return 0;
3378}
3379
3380static __maybe_unused int sci_resume(struct device *dev)
3381{
3382 struct sci_port *sport = dev_get_drvdata(dev);
3383
3384 if (sport)
3385 uart_resume_port(&sci_uart_driver, &sport->port);
3386
3387 return 0;
3388}
3389
3390static SIMPLE_DEV_PM_OPS(sci_dev_pm_ops, sci_suspend, sci_resume);
3391
3392static struct platform_driver sci_driver = {
3393 .probe = sci_probe,
3394 .remove = sci_remove,
3395 .driver = {
3396 .name = "sh-sci",
3397 .pm = &sci_dev_pm_ops,
3398 .of_match_table = of_match_ptr(of_sci_match),
3399 },
3400};
3401
3402static int __init sci_init(void)
3403{
3404 pr_info("%s\n", banner);
3405
3406 return platform_driver_register(&sci_driver);
3407}
3408
3409static void __exit sci_exit(void)
3410{
3411 platform_driver_unregister(&sci_driver);
3412
3413 if (sci_uart_driver.state)
3414 uart_unregister_driver(&sci_uart_driver);
3415}
3416
3417#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
3418early_platform_init_buffer("earlyprintk", &sci_driver,
3419 early_serial_buf, ARRAY_SIZE(early_serial_buf));
3420#endif
3421#ifdef CONFIG_SERIAL_SH_SCI_EARLYCON
3422static struct plat_sci_port port_cfg __initdata;
3423
3424static int __init early_console_setup(struct earlycon_device *device,
3425 int type)
3426{
3427 if (!device->port.membase)
3428 return -ENODEV;
3429
3430 device->port.serial_in = sci_serial_in;
3431 device->port.serial_out = sci_serial_out;
3432 device->port.type = type;
3433 memcpy(&sci_ports[0].port, &device->port, sizeof(struct uart_port));
3434 port_cfg.type = type;
3435 sci_ports[0].cfg = &port_cfg;
3436 sci_ports[0].params = sci_probe_regmap(&port_cfg);
3437 port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR);
3438 sci_serial_out(&sci_ports[0].port, SCSCR,
3439 SCSCR_RE | SCSCR_TE | port_cfg.scscr);
3440
3441 device->con->write = serial_console_write;
3442 return 0;
3443}
3444static int __init sci_early_console_setup(struct earlycon_device *device,
3445 const char *opt)
3446{
3447 return early_console_setup(device, PORT_SCI);
3448}
3449static int __init scif_early_console_setup(struct earlycon_device *device,
3450 const char *opt)
3451{
3452 return early_console_setup(device, PORT_SCIF);
3453}
3454static int __init rzscifa_early_console_setup(struct earlycon_device *device,
3455 const char *opt)
3456{
3457 port_cfg.regtype = SCIx_RZ_SCIFA_REGTYPE;
3458 return early_console_setup(device, PORT_SCIF);
3459}
3460static int __init scifa_early_console_setup(struct earlycon_device *device,
3461 const char *opt)
3462{
3463 return early_console_setup(device, PORT_SCIFA);
3464}
3465static int __init scifb_early_console_setup(struct earlycon_device *device,
3466 const char *opt)
3467{
3468 return early_console_setup(device, PORT_SCIFB);
3469}
3470static int __init hscif_early_console_setup(struct earlycon_device *device,
3471 const char *opt)
3472{
3473 return early_console_setup(device, PORT_HSCIF);
3474}
3475
3476OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup);
3477OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup);
3478OF_EARLYCON_DECLARE(scif, "renesas,scif-r7s9210", rzscifa_early_console_setup);
3479OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup);
3480OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup);
3481OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup);
3482#endif /* CONFIG_SERIAL_SH_SCI_EARLYCON */
3483
3484module_init(sci_init);
3485module_exit(sci_exit);
3486
3487MODULE_LICENSE("GPL");
3488MODULE_ALIAS("platform:sh-sci");
3489MODULE_AUTHOR("Paul Mundt");
3490MODULE_DESCRIPTION("SuperH (H)SCI(F) serial driver");
1/*
2 * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
3 *
4 * Copyright (C) 2002 - 2011 Paul Mundt
5 * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
6 *
7 * based off of the old drivers/char/sh-sci.c by:
8 *
9 * Copyright (C) 1999, 2000 Niibe Yutaka
10 * Copyright (C) 2000 Sugioka Toshinobu
11 * Modified to support multiple serial ports. Stuart Menefy (May 2000).
12 * Modified to support SecureEdge. David McCullough (2002)
13 * Modified to support SH7300 SCIF. Takashi Kusuda (Jun 2003).
14 * Removed SH7300 support (Jul 2007).
15 *
16 * This file is subject to the terms and conditions of the GNU General Public
17 * License. See the file "COPYING" in the main directory of this archive
18 * for more details.
19 */
20#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
21#define SUPPORT_SYSRQ
22#endif
23
24#undef DEBUG
25
26#include <linux/clk.h>
27#include <linux/console.h>
28#include <linux/ctype.h>
29#include <linux/cpufreq.h>
30#include <linux/delay.h>
31#include <linux/dmaengine.h>
32#include <linux/dma-mapping.h>
33#include <linux/err.h>
34#include <linux/errno.h>
35#include <linux/init.h>
36#include <linux/interrupt.h>
37#include <linux/ioport.h>
38#include <linux/major.h>
39#include <linux/module.h>
40#include <linux/mm.h>
41#include <linux/notifier.h>
42#include <linux/of.h>
43#include <linux/platform_device.h>
44#include <linux/pm_runtime.h>
45#include <linux/scatterlist.h>
46#include <linux/serial.h>
47#include <linux/serial_sci.h>
48#include <linux/sh_dma.h>
49#include <linux/slab.h>
50#include <linux/string.h>
51#include <linux/sysrq.h>
52#include <linux/timer.h>
53#include <linux/tty.h>
54#include <linux/tty_flip.h>
55
56#ifdef CONFIG_SUPERH
57#include <asm/sh_bios.h>
58#endif
59
60#include "sh-sci.h"
61
62/* Offsets into the sci_port->irqs array */
63enum {
64 SCIx_ERI_IRQ,
65 SCIx_RXI_IRQ,
66 SCIx_TXI_IRQ,
67 SCIx_BRI_IRQ,
68 SCIx_NR_IRQS,
69
70 SCIx_MUX_IRQ = SCIx_NR_IRQS, /* special case */
71};
72
73#define SCIx_IRQ_IS_MUXED(port) \
74 ((port)->irqs[SCIx_ERI_IRQ] == \
75 (port)->irqs[SCIx_RXI_IRQ]) || \
76 ((port)->irqs[SCIx_ERI_IRQ] && \
77 ((port)->irqs[SCIx_RXI_IRQ] < 0))
78
79struct sci_port {
80 struct uart_port port;
81
82 /* Platform configuration */
83 struct plat_sci_port *cfg;
84 int overrun_bit;
85 unsigned int error_mask;
86 unsigned int sampling_rate;
87
88
89 /* Break timer */
90 struct timer_list break_timer;
91 int break_flag;
92
93 /* Interface clock */
94 struct clk *iclk;
95 /* Function clock */
96 struct clk *fclk;
97
98 int irqs[SCIx_NR_IRQS];
99 char *irqstr[SCIx_NR_IRQS];
100
101 struct dma_chan *chan_tx;
102 struct dma_chan *chan_rx;
103
104#ifdef CONFIG_SERIAL_SH_SCI_DMA
105 struct dma_async_tx_descriptor *desc_tx;
106 struct dma_async_tx_descriptor *desc_rx[2];
107 dma_cookie_t cookie_tx;
108 dma_cookie_t cookie_rx[2];
109 dma_cookie_t active_rx;
110 struct scatterlist sg_tx;
111 unsigned int sg_len_tx;
112 struct scatterlist sg_rx[2];
113 size_t buf_len_rx;
114 struct sh_dmae_slave param_tx;
115 struct sh_dmae_slave param_rx;
116 struct work_struct work_tx;
117 struct work_struct work_rx;
118 struct timer_list rx_timer;
119 unsigned int rx_timeout;
120#endif
121
122 struct notifier_block freq_transition;
123};
124
125/* Function prototypes */
126static void sci_start_tx(struct uart_port *port);
127static void sci_stop_tx(struct uart_port *port);
128static void sci_start_rx(struct uart_port *port);
129
130#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS
131
132static struct sci_port sci_ports[SCI_NPORTS];
133static struct uart_driver sci_uart_driver;
134
135static inline struct sci_port *
136to_sci_port(struct uart_port *uart)
137{
138 return container_of(uart, struct sci_port, port);
139}
140
141struct plat_sci_reg {
142 u8 offset, size;
143};
144
145/* Helper for invalidating specific entries of an inherited map. */
146#define sci_reg_invalid { .offset = 0, .size = 0 }
147
148static struct plat_sci_reg sci_regmap[SCIx_NR_REGTYPES][SCIx_NR_REGS] = {
149 [SCIx_PROBE_REGTYPE] = {
150 [0 ... SCIx_NR_REGS - 1] = sci_reg_invalid,
151 },
152
153 /*
154 * Common SCI definitions, dependent on the port's regshift
155 * value.
156 */
157 [SCIx_SCI_REGTYPE] = {
158 [SCSMR] = { 0x00, 8 },
159 [SCBRR] = { 0x01, 8 },
160 [SCSCR] = { 0x02, 8 },
161 [SCxTDR] = { 0x03, 8 },
162 [SCxSR] = { 0x04, 8 },
163 [SCxRDR] = { 0x05, 8 },
164 [SCFCR] = sci_reg_invalid,
165 [SCFDR] = sci_reg_invalid,
166 [SCTFDR] = sci_reg_invalid,
167 [SCRFDR] = sci_reg_invalid,
168 [SCSPTR] = sci_reg_invalid,
169 [SCLSR] = sci_reg_invalid,
170 [HSSRR] = sci_reg_invalid,
171 },
172
173 /*
174 * Common definitions for legacy IrDA ports, dependent on
175 * regshift value.
176 */
177 [SCIx_IRDA_REGTYPE] = {
178 [SCSMR] = { 0x00, 8 },
179 [SCBRR] = { 0x01, 8 },
180 [SCSCR] = { 0x02, 8 },
181 [SCxTDR] = { 0x03, 8 },
182 [SCxSR] = { 0x04, 8 },
183 [SCxRDR] = { 0x05, 8 },
184 [SCFCR] = { 0x06, 8 },
185 [SCFDR] = { 0x07, 16 },
186 [SCTFDR] = sci_reg_invalid,
187 [SCRFDR] = sci_reg_invalid,
188 [SCSPTR] = sci_reg_invalid,
189 [SCLSR] = sci_reg_invalid,
190 [HSSRR] = sci_reg_invalid,
191 },
192
193 /*
194 * Common SCIFA definitions.
195 */
196 [SCIx_SCIFA_REGTYPE] = {
197 [SCSMR] = { 0x00, 16 },
198 [SCBRR] = { 0x04, 8 },
199 [SCSCR] = { 0x08, 16 },
200 [SCxTDR] = { 0x20, 8 },
201 [SCxSR] = { 0x14, 16 },
202 [SCxRDR] = { 0x24, 8 },
203 [SCFCR] = { 0x18, 16 },
204 [SCFDR] = { 0x1c, 16 },
205 [SCTFDR] = sci_reg_invalid,
206 [SCRFDR] = sci_reg_invalid,
207 [SCSPTR] = sci_reg_invalid,
208 [SCLSR] = sci_reg_invalid,
209 [HSSRR] = sci_reg_invalid,
210 },
211
212 /*
213 * Common SCIFB definitions.
214 */
215 [SCIx_SCIFB_REGTYPE] = {
216 [SCSMR] = { 0x00, 16 },
217 [SCBRR] = { 0x04, 8 },
218 [SCSCR] = { 0x08, 16 },
219 [SCxTDR] = { 0x40, 8 },
220 [SCxSR] = { 0x14, 16 },
221 [SCxRDR] = { 0x60, 8 },
222 [SCFCR] = { 0x18, 16 },
223 [SCFDR] = sci_reg_invalid,
224 [SCTFDR] = { 0x38, 16 },
225 [SCRFDR] = { 0x3c, 16 },
226 [SCSPTR] = sci_reg_invalid,
227 [SCLSR] = sci_reg_invalid,
228 [HSSRR] = sci_reg_invalid,
229 },
230
231 /*
232 * Common SH-2(A) SCIF definitions for ports with FIFO data
233 * count registers.
234 */
235 [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
236 [SCSMR] = { 0x00, 16 },
237 [SCBRR] = { 0x04, 8 },
238 [SCSCR] = { 0x08, 16 },
239 [SCxTDR] = { 0x0c, 8 },
240 [SCxSR] = { 0x10, 16 },
241 [SCxRDR] = { 0x14, 8 },
242 [SCFCR] = { 0x18, 16 },
243 [SCFDR] = { 0x1c, 16 },
244 [SCTFDR] = sci_reg_invalid,
245 [SCRFDR] = sci_reg_invalid,
246 [SCSPTR] = { 0x20, 16 },
247 [SCLSR] = { 0x24, 16 },
248 [HSSRR] = sci_reg_invalid,
249 },
250
251 /*
252 * Common SH-3 SCIF definitions.
253 */
254 [SCIx_SH3_SCIF_REGTYPE] = {
255 [SCSMR] = { 0x00, 8 },
256 [SCBRR] = { 0x02, 8 },
257 [SCSCR] = { 0x04, 8 },
258 [SCxTDR] = { 0x06, 8 },
259 [SCxSR] = { 0x08, 16 },
260 [SCxRDR] = { 0x0a, 8 },
261 [SCFCR] = { 0x0c, 8 },
262 [SCFDR] = { 0x0e, 16 },
263 [SCTFDR] = sci_reg_invalid,
264 [SCRFDR] = sci_reg_invalid,
265 [SCSPTR] = sci_reg_invalid,
266 [SCLSR] = sci_reg_invalid,
267 [HSSRR] = sci_reg_invalid,
268 },
269
270 /*
271 * Common SH-4(A) SCIF(B) definitions.
272 */
273 [SCIx_SH4_SCIF_REGTYPE] = {
274 [SCSMR] = { 0x00, 16 },
275 [SCBRR] = { 0x04, 8 },
276 [SCSCR] = { 0x08, 16 },
277 [SCxTDR] = { 0x0c, 8 },
278 [SCxSR] = { 0x10, 16 },
279 [SCxRDR] = { 0x14, 8 },
280 [SCFCR] = { 0x18, 16 },
281 [SCFDR] = { 0x1c, 16 },
282 [SCTFDR] = sci_reg_invalid,
283 [SCRFDR] = sci_reg_invalid,
284 [SCSPTR] = { 0x20, 16 },
285 [SCLSR] = { 0x24, 16 },
286 [HSSRR] = sci_reg_invalid,
287 },
288
289 /*
290 * Common HSCIF definitions.
291 */
292 [SCIx_HSCIF_REGTYPE] = {
293 [SCSMR] = { 0x00, 16 },
294 [SCBRR] = { 0x04, 8 },
295 [SCSCR] = { 0x08, 16 },
296 [SCxTDR] = { 0x0c, 8 },
297 [SCxSR] = { 0x10, 16 },
298 [SCxRDR] = { 0x14, 8 },
299 [SCFCR] = { 0x18, 16 },
300 [SCFDR] = { 0x1c, 16 },
301 [SCTFDR] = sci_reg_invalid,
302 [SCRFDR] = sci_reg_invalid,
303 [SCSPTR] = { 0x20, 16 },
304 [SCLSR] = { 0x24, 16 },
305 [HSSRR] = { 0x40, 16 },
306 },
307
308 /*
309 * Common SH-4(A) SCIF(B) definitions for ports without an SCSPTR
310 * register.
311 */
312 [SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE] = {
313 [SCSMR] = { 0x00, 16 },
314 [SCBRR] = { 0x04, 8 },
315 [SCSCR] = { 0x08, 16 },
316 [SCxTDR] = { 0x0c, 8 },
317 [SCxSR] = { 0x10, 16 },
318 [SCxRDR] = { 0x14, 8 },
319 [SCFCR] = { 0x18, 16 },
320 [SCFDR] = { 0x1c, 16 },
321 [SCTFDR] = sci_reg_invalid,
322 [SCRFDR] = sci_reg_invalid,
323 [SCSPTR] = sci_reg_invalid,
324 [SCLSR] = { 0x24, 16 },
325 [HSSRR] = sci_reg_invalid,
326 },
327
328 /*
329 * Common SH-4(A) SCIF(B) definitions for ports with FIFO data
330 * count registers.
331 */
332 [SCIx_SH4_SCIF_FIFODATA_REGTYPE] = {
333 [SCSMR] = { 0x00, 16 },
334 [SCBRR] = { 0x04, 8 },
335 [SCSCR] = { 0x08, 16 },
336 [SCxTDR] = { 0x0c, 8 },
337 [SCxSR] = { 0x10, 16 },
338 [SCxRDR] = { 0x14, 8 },
339 [SCFCR] = { 0x18, 16 },
340 [SCFDR] = { 0x1c, 16 },
341 [SCTFDR] = { 0x1c, 16 }, /* aliased to SCFDR */
342 [SCRFDR] = { 0x20, 16 },
343 [SCSPTR] = { 0x24, 16 },
344 [SCLSR] = { 0x28, 16 },
345 [HSSRR] = sci_reg_invalid,
346 },
347
348 /*
349 * SH7705-style SCIF(B) ports, lacking both SCSPTR and SCLSR
350 * registers.
351 */
352 [SCIx_SH7705_SCIF_REGTYPE] = {
353 [SCSMR] = { 0x00, 16 },
354 [SCBRR] = { 0x04, 8 },
355 [SCSCR] = { 0x08, 16 },
356 [SCxTDR] = { 0x20, 8 },
357 [SCxSR] = { 0x14, 16 },
358 [SCxRDR] = { 0x24, 8 },
359 [SCFCR] = { 0x18, 16 },
360 [SCFDR] = { 0x1c, 16 },
361 [SCTFDR] = sci_reg_invalid,
362 [SCRFDR] = sci_reg_invalid,
363 [SCSPTR] = sci_reg_invalid,
364 [SCLSR] = sci_reg_invalid,
365 [HSSRR] = sci_reg_invalid,
366 },
367};
368
369#define sci_getreg(up, offset) (sci_regmap[to_sci_port(up)->cfg->regtype] + offset)
370
371/*
372 * The "offset" here is rather misleading, in that it refers to an enum
373 * value relative to the port mapping rather than the fixed offset
374 * itself, which needs to be manually retrieved from the platform's
375 * register map for the given port.
376 */
377static unsigned int sci_serial_in(struct uart_port *p, int offset)
378{
379 struct plat_sci_reg *reg = sci_getreg(p, offset);
380
381 if (reg->size == 8)
382 return ioread8(p->membase + (reg->offset << p->regshift));
383 else if (reg->size == 16)
384 return ioread16(p->membase + (reg->offset << p->regshift));
385 else
386 WARN(1, "Invalid register access\n");
387
388 return 0;
389}
390
391static void sci_serial_out(struct uart_port *p, int offset, int value)
392{
393 struct plat_sci_reg *reg = sci_getreg(p, offset);
394
395 if (reg->size == 8)
396 iowrite8(value, p->membase + (reg->offset << p->regshift));
397 else if (reg->size == 16)
398 iowrite16(value, p->membase + (reg->offset << p->regshift));
399 else
400 WARN(1, "Invalid register access\n");
401}
402
403static int sci_probe_regmap(struct plat_sci_port *cfg)
404{
405 switch (cfg->type) {
406 case PORT_SCI:
407 cfg->regtype = SCIx_SCI_REGTYPE;
408 break;
409 case PORT_IRDA:
410 cfg->regtype = SCIx_IRDA_REGTYPE;
411 break;
412 case PORT_SCIFA:
413 cfg->regtype = SCIx_SCIFA_REGTYPE;
414 break;
415 case PORT_SCIFB:
416 cfg->regtype = SCIx_SCIFB_REGTYPE;
417 break;
418 case PORT_SCIF:
419 /*
420 * The SH-4 is a bit of a misnomer here, although that's
421 * where this particular port layout originated. This
422 * configuration (or some slight variation thereof)
423 * remains the dominant model for all SCIFs.
424 */
425 cfg->regtype = SCIx_SH4_SCIF_REGTYPE;
426 break;
427 case PORT_HSCIF:
428 cfg->regtype = SCIx_HSCIF_REGTYPE;
429 break;
430 default:
431 pr_err("Can't probe register map for given port\n");
432 return -EINVAL;
433 }
434
435 return 0;
436}
437
438static void sci_port_enable(struct sci_port *sci_port)
439{
440 if (!sci_port->port.dev)
441 return;
442
443 pm_runtime_get_sync(sci_port->port.dev);
444
445 clk_prepare_enable(sci_port->iclk);
446 sci_port->port.uartclk = clk_get_rate(sci_port->iclk);
447 clk_prepare_enable(sci_port->fclk);
448}
449
450static void sci_port_disable(struct sci_port *sci_port)
451{
452 if (!sci_port->port.dev)
453 return;
454
455 /* Cancel the break timer to ensure that the timer handler will not try
456 * to access the hardware with clocks and power disabled. Reset the
457 * break flag to make the break debouncing state machine ready for the
458 * next break.
459 */
460 del_timer_sync(&sci_port->break_timer);
461 sci_port->break_flag = 0;
462
463 clk_disable_unprepare(sci_port->fclk);
464 clk_disable_unprepare(sci_port->iclk);
465
466 pm_runtime_put_sync(sci_port->port.dev);
467}
468
469#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE)
470
471#ifdef CONFIG_CONSOLE_POLL
472static int sci_poll_get_char(struct uart_port *port)
473{
474 unsigned short status;
475 int c;
476
477 do {
478 status = serial_port_in(port, SCxSR);
479 if (status & SCxSR_ERRORS(port)) {
480 serial_port_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));
481 continue;
482 }
483 break;
484 } while (1);
485
486 if (!(status & SCxSR_RDxF(port)))
487 return NO_POLL_CHAR;
488
489 c = serial_port_in(port, SCxRDR);
490
491 /* Dummy read */
492 serial_port_in(port, SCxSR);
493 serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
494
495 return c;
496}
497#endif
498
499static void sci_poll_put_char(struct uart_port *port, unsigned char c)
500{
501 unsigned short status;
502
503 do {
504 status = serial_port_in(port, SCxSR);
505 } while (!(status & SCxSR_TDxE(port)));
506
507 serial_port_out(port, SCxTDR, c);
508 serial_port_out(port, SCxSR, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
509}
510#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE */
511
512static void sci_init_pins(struct uart_port *port, unsigned int cflag)
513{
514 struct sci_port *s = to_sci_port(port);
515 struct plat_sci_reg *reg = sci_regmap[s->cfg->regtype] + SCSPTR;
516
517 /*
518 * Use port-specific handler if provided.
519 */
520 if (s->cfg->ops && s->cfg->ops->init_pins) {
521 s->cfg->ops->init_pins(port, cflag);
522 return;
523 }
524
525 /*
526 * For the generic path SCSPTR is necessary. Bail out if that's
527 * unavailable, too.
528 */
529 if (!reg->size)
530 return;
531
532 if ((s->cfg->capabilities & SCIx_HAVE_RTSCTS) &&
533 ((!(cflag & CRTSCTS)))) {
534 unsigned short status;
535
536 status = serial_port_in(port, SCSPTR);
537 status &= ~SCSPTR_CTSIO;
538 status |= SCSPTR_RTSIO;
539 serial_port_out(port, SCSPTR, status); /* Set RTS = 1 */
540 }
541}
542
543static int sci_txfill(struct uart_port *port)
544{
545 struct plat_sci_reg *reg;
546
547 reg = sci_getreg(port, SCTFDR);
548 if (reg->size)
549 return serial_port_in(port, SCTFDR) & ((port->fifosize << 1) - 1);
550
551 reg = sci_getreg(port, SCFDR);
552 if (reg->size)
553 return serial_port_in(port, SCFDR) >> 8;
554
555 return !(serial_port_in(port, SCxSR) & SCI_TDRE);
556}
557
558static int sci_txroom(struct uart_port *port)
559{
560 return port->fifosize - sci_txfill(port);
561}
562
563static int sci_rxfill(struct uart_port *port)
564{
565 struct plat_sci_reg *reg;
566
567 reg = sci_getreg(port, SCRFDR);
568 if (reg->size)
569 return serial_port_in(port, SCRFDR) & ((port->fifosize << 1) - 1);
570
571 reg = sci_getreg(port, SCFDR);
572 if (reg->size)
573 return serial_port_in(port, SCFDR) & ((port->fifosize << 1) - 1);
574
575 return (serial_port_in(port, SCxSR) & SCxSR_RDxF(port)) != 0;
576}
577
578/*
579 * SCI helper for checking the state of the muxed port/RXD pins.
580 */
581static inline int sci_rxd_in(struct uart_port *port)
582{
583 struct sci_port *s = to_sci_port(port);
584
585 if (s->cfg->port_reg <= 0)
586 return 1;
587
588 /* Cast for ARM damage */
589 return !!__raw_readb((void __iomem *)(uintptr_t)s->cfg->port_reg);
590}
591
592/* ********************************************************************** *
593 * the interrupt related routines *
594 * ********************************************************************** */
595
596static void sci_transmit_chars(struct uart_port *port)
597{
598 struct circ_buf *xmit = &port->state->xmit;
599 unsigned int stopped = uart_tx_stopped(port);
600 unsigned short status;
601 unsigned short ctrl;
602 int count;
603
604 status = serial_port_in(port, SCxSR);
605 if (!(status & SCxSR_TDxE(port))) {
606 ctrl = serial_port_in(port, SCSCR);
607 if (uart_circ_empty(xmit))
608 ctrl &= ~SCSCR_TIE;
609 else
610 ctrl |= SCSCR_TIE;
611 serial_port_out(port, SCSCR, ctrl);
612 return;
613 }
614
615 count = sci_txroom(port);
616
617 do {
618 unsigned char c;
619
620 if (port->x_char) {
621 c = port->x_char;
622 port->x_char = 0;
623 } else if (!uart_circ_empty(xmit) && !stopped) {
624 c = xmit->buf[xmit->tail];
625 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
626 } else {
627 break;
628 }
629
630 serial_port_out(port, SCxTDR, c);
631
632 port->icount.tx++;
633 } while (--count > 0);
634
635 serial_port_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
636
637 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
638 uart_write_wakeup(port);
639 if (uart_circ_empty(xmit)) {
640 sci_stop_tx(port);
641 } else {
642 ctrl = serial_port_in(port, SCSCR);
643
644 if (port->type != PORT_SCI) {
645 serial_port_in(port, SCxSR); /* Dummy read */
646 serial_port_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
647 }
648
649 ctrl |= SCSCR_TIE;
650 serial_port_out(port, SCSCR, ctrl);
651 }
652}
653
654/* On SH3, SCIF may read end-of-break as a space->mark char */
655#define STEPFN(c) ({int __c = (c); (((__c-1)|(__c)) == -1); })
656
657static void sci_receive_chars(struct uart_port *port)
658{
659 struct sci_port *sci_port = to_sci_port(port);
660 struct tty_port *tport = &port->state->port;
661 int i, count, copied = 0;
662 unsigned short status;
663 unsigned char flag;
664
665 status = serial_port_in(port, SCxSR);
666 if (!(status & SCxSR_RDxF(port)))
667 return;
668
669 while (1) {
670 /* Don't copy more bytes than there is room for in the buffer */
671 count = tty_buffer_request_room(tport, sci_rxfill(port));
672
673 /* If for any reason we can't copy more data, we're done! */
674 if (count == 0)
675 break;
676
677 if (port->type == PORT_SCI) {
678 char c = serial_port_in(port, SCxRDR);
679 if (uart_handle_sysrq_char(port, c) ||
680 sci_port->break_flag)
681 count = 0;
682 else
683 tty_insert_flip_char(tport, c, TTY_NORMAL);
684 } else {
685 for (i = 0; i < count; i++) {
686 char c = serial_port_in(port, SCxRDR);
687
688 status = serial_port_in(port, SCxSR);
689#if defined(CONFIG_CPU_SH3)
690 /* Skip "chars" during break */
691 if (sci_port->break_flag) {
692 if ((c == 0) &&
693 (status & SCxSR_FER(port))) {
694 count--; i--;
695 continue;
696 }
697
698 /* Nonzero => end-of-break */
699 dev_dbg(port->dev, "debounce<%02x>\n", c);
700 sci_port->break_flag = 0;
701
702 if (STEPFN(c)) {
703 count--; i--;
704 continue;
705 }
706 }
707#endif /* CONFIG_CPU_SH3 */
708 if (uart_handle_sysrq_char(port, c)) {
709 count--; i--;
710 continue;
711 }
712
713 /* Store data and status */
714 if (status & SCxSR_FER(port)) {
715 flag = TTY_FRAME;
716 port->icount.frame++;
717 dev_notice(port->dev, "frame error\n");
718 } else if (status & SCxSR_PER(port)) {
719 flag = TTY_PARITY;
720 port->icount.parity++;
721 dev_notice(port->dev, "parity error\n");
722 } else
723 flag = TTY_NORMAL;
724
725 tty_insert_flip_char(tport, c, flag);
726 }
727 }
728
729 serial_port_in(port, SCxSR); /* dummy read */
730 serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
731
732 copied += count;
733 port->icount.rx += count;
734 }
735
736 if (copied) {
737 /* Tell the rest of the system the news. New characters! */
738 tty_flip_buffer_push(tport);
739 } else {
740 serial_port_in(port, SCxSR); /* dummy read */
741 serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
742 }
743}
744
745#define SCI_BREAK_JIFFIES (HZ/20)
746
747/*
748 * The sci generates interrupts during the break,
749 * 1 per millisecond or so during the break period, for 9600 baud.
750 * So dont bother disabling interrupts.
751 * But dont want more than 1 break event.
752 * Use a kernel timer to periodically poll the rx line until
753 * the break is finished.
754 */
755static inline void sci_schedule_break_timer(struct sci_port *port)
756{
757 mod_timer(&port->break_timer, jiffies + SCI_BREAK_JIFFIES);
758}
759
760/* Ensure that two consecutive samples find the break over. */
761static void sci_break_timer(unsigned long data)
762{
763 struct sci_port *port = (struct sci_port *)data;
764
765 if (sci_rxd_in(&port->port) == 0) {
766 port->break_flag = 1;
767 sci_schedule_break_timer(port);
768 } else if (port->break_flag == 1) {
769 /* break is over. */
770 port->break_flag = 2;
771 sci_schedule_break_timer(port);
772 } else
773 port->break_flag = 0;
774}
775
776static int sci_handle_errors(struct uart_port *port)
777{
778 int copied = 0;
779 unsigned short status = serial_port_in(port, SCxSR);
780 struct tty_port *tport = &port->state->port;
781 struct sci_port *s = to_sci_port(port);
782
783 /* Handle overruns */
784 if (status & (1 << s->overrun_bit)) {
785 port->icount.overrun++;
786
787 /* overrun error */
788 if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
789 copied++;
790
791 dev_notice(port->dev, "overrun error\n");
792 }
793
794 if (status & SCxSR_FER(port)) {
795 if (sci_rxd_in(port) == 0) {
796 /* Notify of BREAK */
797 struct sci_port *sci_port = to_sci_port(port);
798
799 if (!sci_port->break_flag) {
800 port->icount.brk++;
801
802 sci_port->break_flag = 1;
803 sci_schedule_break_timer(sci_port);
804
805 /* Do sysrq handling. */
806 if (uart_handle_break(port))
807 return 0;
808
809 dev_dbg(port->dev, "BREAK detected\n");
810
811 if (tty_insert_flip_char(tport, 0, TTY_BREAK))
812 copied++;
813 }
814
815 } else {
816 /* frame error */
817 port->icount.frame++;
818
819 if (tty_insert_flip_char(tport, 0, TTY_FRAME))
820 copied++;
821
822 dev_notice(port->dev, "frame error\n");
823 }
824 }
825
826 if (status & SCxSR_PER(port)) {
827 /* parity error */
828 port->icount.parity++;
829
830 if (tty_insert_flip_char(tport, 0, TTY_PARITY))
831 copied++;
832
833 dev_notice(port->dev, "parity error\n");
834 }
835
836 if (copied)
837 tty_flip_buffer_push(tport);
838
839 return copied;
840}
841
842static int sci_handle_fifo_overrun(struct uart_port *port)
843{
844 struct tty_port *tport = &port->state->port;
845 struct sci_port *s = to_sci_port(port);
846 struct plat_sci_reg *reg;
847 int copied = 0;
848
849 reg = sci_getreg(port, SCLSR);
850 if (!reg->size)
851 return 0;
852
853 if ((serial_port_in(port, SCLSR) & (1 << s->overrun_bit))) {
854 serial_port_out(port, SCLSR, 0);
855
856 port->icount.overrun++;
857
858 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
859 tty_flip_buffer_push(tport);
860
861 dev_notice(port->dev, "overrun error\n");
862 copied++;
863 }
864
865 return copied;
866}
867
868static int sci_handle_breaks(struct uart_port *port)
869{
870 int copied = 0;
871 unsigned short status = serial_port_in(port, SCxSR);
872 struct tty_port *tport = &port->state->port;
873 struct sci_port *s = to_sci_port(port);
874
875 if (uart_handle_break(port))
876 return 0;
877
878 if (!s->break_flag && status & SCxSR_BRK(port)) {
879#if defined(CONFIG_CPU_SH3)
880 /* Debounce break */
881 s->break_flag = 1;
882#endif
883
884 port->icount.brk++;
885
886 /* Notify of BREAK */
887 if (tty_insert_flip_char(tport, 0, TTY_BREAK))
888 copied++;
889
890 dev_dbg(port->dev, "BREAK detected\n");
891 }
892
893 if (copied)
894 tty_flip_buffer_push(tport);
895
896 copied += sci_handle_fifo_overrun(port);
897
898 return copied;
899}
900
901static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
902{
903#ifdef CONFIG_SERIAL_SH_SCI_DMA
904 struct uart_port *port = ptr;
905 struct sci_port *s = to_sci_port(port);
906
907 if (s->chan_rx) {
908 u16 scr = serial_port_in(port, SCSCR);
909 u16 ssr = serial_port_in(port, SCxSR);
910
911 /* Disable future Rx interrupts */
912 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
913 disable_irq_nosync(irq);
914 scr |= SCSCR_RDRQE;
915 } else {
916 scr &= ~SCSCR_RIE;
917 }
918 serial_port_out(port, SCSCR, scr);
919 /* Clear current interrupt */
920 serial_port_out(port, SCxSR, ssr & ~(1 | SCxSR_RDxF(port)));
921 dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u jiffies\n",
922 jiffies, s->rx_timeout);
923 mod_timer(&s->rx_timer, jiffies + s->rx_timeout);
924
925 return IRQ_HANDLED;
926 }
927#endif
928
929 /* I think sci_receive_chars has to be called irrespective
930 * of whether the I_IXOFF is set, otherwise, how is the interrupt
931 * to be disabled?
932 */
933 sci_receive_chars(ptr);
934
935 return IRQ_HANDLED;
936}
937
938static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
939{
940 struct uart_port *port = ptr;
941 unsigned long flags;
942
943 spin_lock_irqsave(&port->lock, flags);
944 sci_transmit_chars(port);
945 spin_unlock_irqrestore(&port->lock, flags);
946
947 return IRQ_HANDLED;
948}
949
950static irqreturn_t sci_er_interrupt(int irq, void *ptr)
951{
952 struct uart_port *port = ptr;
953
954 /* Handle errors */
955 if (port->type == PORT_SCI) {
956 if (sci_handle_errors(port)) {
957 /* discard character in rx buffer */
958 serial_port_in(port, SCxSR);
959 serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
960 }
961 } else {
962 sci_handle_fifo_overrun(port);
963 sci_rx_interrupt(irq, ptr);
964 }
965
966 serial_port_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));
967
968 /* Kick the transmission */
969 sci_tx_interrupt(irq, ptr);
970
971 return IRQ_HANDLED;
972}
973
974static irqreturn_t sci_br_interrupt(int irq, void *ptr)
975{
976 struct uart_port *port = ptr;
977
978 /* Handle BREAKs */
979 sci_handle_breaks(port);
980 serial_port_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
981
982 return IRQ_HANDLED;
983}
984
985static inline unsigned long port_rx_irq_mask(struct uart_port *port)
986{
987 /*
988 * Not all ports (such as SCIFA) will support REIE. Rather than
989 * special-casing the port type, we check the port initialization
990 * IRQ enable mask to see whether the IRQ is desired at all. If
991 * it's unset, it's logically inferred that there's no point in
992 * testing for it.
993 */
994 return SCSCR_RIE | (to_sci_port(port)->cfg->scscr & SCSCR_REIE);
995}
996
997static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
998{
999 unsigned short ssr_status, scr_status, err_enabled;
1000 struct uart_port *port = ptr;
1001 struct sci_port *s = to_sci_port(port);
1002 irqreturn_t ret = IRQ_NONE;
1003
1004 ssr_status = serial_port_in(port, SCxSR);
1005 scr_status = serial_port_in(port, SCSCR);
1006 err_enabled = scr_status & port_rx_irq_mask(port);
1007
1008 /* Tx Interrupt */
1009 if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) &&
1010 !s->chan_tx)
1011 ret = sci_tx_interrupt(irq, ptr);
1012
1013 /*
1014 * Rx Interrupt: if we're using DMA, the DMA controller clears RDF /
1015 * DR flags
1016 */
1017 if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) &&
1018 (scr_status & SCSCR_RIE))
1019 ret = sci_rx_interrupt(irq, ptr);
1020
1021 /* Error Interrupt */
1022 if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled)
1023 ret = sci_er_interrupt(irq, ptr);
1024
1025 /* Break Interrupt */
1026 if ((ssr_status & SCxSR_BRK(port)) && err_enabled)
1027 ret = sci_br_interrupt(irq, ptr);
1028
1029 return ret;
1030}
1031
1032/*
1033 * Here we define a transition notifier so that we can update all of our
1034 * ports' baud rate when the peripheral clock changes.
1035 */
1036static int sci_notifier(struct notifier_block *self,
1037 unsigned long phase, void *p)
1038{
1039 struct sci_port *sci_port;
1040 unsigned long flags;
1041
1042 sci_port = container_of(self, struct sci_port, freq_transition);
1043
1044 if (phase == CPUFREQ_POSTCHANGE) {
1045 struct uart_port *port = &sci_port->port;
1046
1047 spin_lock_irqsave(&port->lock, flags);
1048 port->uartclk = clk_get_rate(sci_port->iclk);
1049 spin_unlock_irqrestore(&port->lock, flags);
1050 }
1051
1052 return NOTIFY_OK;
1053}
1054
1055static struct sci_irq_desc {
1056 const char *desc;
1057 irq_handler_t handler;
1058} sci_irq_desc[] = {
1059 /*
1060 * Split out handlers, the default case.
1061 */
1062 [SCIx_ERI_IRQ] = {
1063 .desc = "rx err",
1064 .handler = sci_er_interrupt,
1065 },
1066
1067 [SCIx_RXI_IRQ] = {
1068 .desc = "rx full",
1069 .handler = sci_rx_interrupt,
1070 },
1071
1072 [SCIx_TXI_IRQ] = {
1073 .desc = "tx empty",
1074 .handler = sci_tx_interrupt,
1075 },
1076
1077 [SCIx_BRI_IRQ] = {
1078 .desc = "break",
1079 .handler = sci_br_interrupt,
1080 },
1081
1082 /*
1083 * Special muxed handler.
1084 */
1085 [SCIx_MUX_IRQ] = {
1086 .desc = "mux",
1087 .handler = sci_mpxed_interrupt,
1088 },
1089};
1090
1091static int sci_request_irq(struct sci_port *port)
1092{
1093 struct uart_port *up = &port->port;
1094 int i, j, ret = 0;
1095
1096 for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
1097 struct sci_irq_desc *desc;
1098 int irq;
1099
1100 if (SCIx_IRQ_IS_MUXED(port)) {
1101 i = SCIx_MUX_IRQ;
1102 irq = up->irq;
1103 } else {
1104 irq = port->irqs[i];
1105
1106 /*
1107 * Certain port types won't support all of the
1108 * available interrupt sources.
1109 */
1110 if (unlikely(irq < 0))
1111 continue;
1112 }
1113
1114 desc = sci_irq_desc + i;
1115 port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
1116 dev_name(up->dev), desc->desc);
1117 if (!port->irqstr[j]) {
1118 dev_err(up->dev, "Failed to allocate %s IRQ string\n",
1119 desc->desc);
1120 goto out_nomem;
1121 }
1122
1123 ret = request_irq(irq, desc->handler, up->irqflags,
1124 port->irqstr[j], port);
1125 if (unlikely(ret)) {
1126 dev_err(up->dev, "Can't allocate %s IRQ\n", desc->desc);
1127 goto out_noirq;
1128 }
1129 }
1130
1131 return 0;
1132
1133out_noirq:
1134 while (--i >= 0)
1135 free_irq(port->irqs[i], port);
1136
1137out_nomem:
1138 while (--j >= 0)
1139 kfree(port->irqstr[j]);
1140
1141 return ret;
1142}
1143
1144static void sci_free_irq(struct sci_port *port)
1145{
1146 int i;
1147
1148 /*
1149 * Intentionally in reverse order so we iterate over the muxed
1150 * IRQ first.
1151 */
1152 for (i = 0; i < SCIx_NR_IRQS; i++) {
1153 int irq = port->irqs[i];
1154
1155 /*
1156 * Certain port types won't support all of the available
1157 * interrupt sources.
1158 */
1159 if (unlikely(irq < 0))
1160 continue;
1161
1162 free_irq(port->irqs[i], port);
1163 kfree(port->irqstr[i]);
1164
1165 if (SCIx_IRQ_IS_MUXED(port)) {
1166 /* If there's only one IRQ, we're done. */
1167 return;
1168 }
1169 }
1170}
1171
1172static unsigned int sci_tx_empty(struct uart_port *port)
1173{
1174 unsigned short status = serial_port_in(port, SCxSR);
1175 unsigned short in_tx_fifo = sci_txfill(port);
1176
1177 return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
1178}
1179
1180/*
1181 * Modem control is a bit of a mixed bag for SCI(F) ports. Generally
1182 * CTS/RTS is supported in hardware by at least one port and controlled
1183 * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently
1184 * handled via the ->init_pins() op, which is a bit of a one-way street,
1185 * lacking any ability to defer pin control -- this will later be
1186 * converted over to the GPIO framework).
1187 *
1188 * Other modes (such as loopback) are supported generically on certain
1189 * port types, but not others. For these it's sufficient to test for the
1190 * existence of the support register and simply ignore the port type.
1191 */
1192static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
1193{
1194 if (mctrl & TIOCM_LOOP) {
1195 struct plat_sci_reg *reg;
1196
1197 /*
1198 * Standard loopback mode for SCFCR ports.
1199 */
1200 reg = sci_getreg(port, SCFCR);
1201 if (reg->size)
1202 serial_port_out(port, SCFCR,
1203 serial_port_in(port, SCFCR) |
1204 SCFCR_LOOP);
1205 }
1206}
1207
1208static unsigned int sci_get_mctrl(struct uart_port *port)
1209{
1210 /*
1211 * CTS/RTS is handled in hardware when supported, while nothing
1212 * else is wired up. Keep it simple and simply assert DSR/CAR.
1213 */
1214 return TIOCM_DSR | TIOCM_CAR;
1215}
1216
1217#ifdef CONFIG_SERIAL_SH_SCI_DMA
1218static void sci_dma_tx_complete(void *arg)
1219{
1220 struct sci_port *s = arg;
1221 struct uart_port *port = &s->port;
1222 struct circ_buf *xmit = &port->state->xmit;
1223 unsigned long flags;
1224
1225 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1226
1227 spin_lock_irqsave(&port->lock, flags);
1228
1229 xmit->tail += sg_dma_len(&s->sg_tx);
1230 xmit->tail &= UART_XMIT_SIZE - 1;
1231
1232 port->icount.tx += sg_dma_len(&s->sg_tx);
1233
1234 async_tx_ack(s->desc_tx);
1235 s->desc_tx = NULL;
1236
1237 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1238 uart_write_wakeup(port);
1239
1240 if (!uart_circ_empty(xmit)) {
1241 s->cookie_tx = 0;
1242 schedule_work(&s->work_tx);
1243 } else {
1244 s->cookie_tx = -EINVAL;
1245 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1246 u16 ctrl = serial_port_in(port, SCSCR);
1247 serial_port_out(port, SCSCR, ctrl & ~SCSCR_TIE);
1248 }
1249 }
1250
1251 spin_unlock_irqrestore(&port->lock, flags);
1252}
1253
1254/* Locking: called with port lock held */
1255static int sci_dma_rx_push(struct sci_port *s, size_t count)
1256{
1257 struct uart_port *port = &s->port;
1258 struct tty_port *tport = &port->state->port;
1259 int i, active, room;
1260
1261 room = tty_buffer_request_room(tport, count);
1262
1263 if (s->active_rx == s->cookie_rx[0]) {
1264 active = 0;
1265 } else if (s->active_rx == s->cookie_rx[1]) {
1266 active = 1;
1267 } else {
1268 dev_err(port->dev, "cookie %d not found!\n", s->active_rx);
1269 return 0;
1270 }
1271
1272 if (room < count)
1273 dev_warn(port->dev, "Rx overrun: dropping %zu bytes\n",
1274 count - room);
1275 if (!room)
1276 return room;
1277
1278 for (i = 0; i < room; i++)
1279 tty_insert_flip_char(tport, ((u8 *)sg_virt(&s->sg_rx[active]))[i],
1280 TTY_NORMAL);
1281
1282 port->icount.rx += room;
1283
1284 return room;
1285}
1286
1287static void sci_dma_rx_complete(void *arg)
1288{
1289 struct sci_port *s = arg;
1290 struct uart_port *port = &s->port;
1291 unsigned long flags;
1292 int count;
1293
1294 dev_dbg(port->dev, "%s(%d) active #%d\n",
1295 __func__, port->line, s->active_rx);
1296
1297 spin_lock_irqsave(&port->lock, flags);
1298
1299 count = sci_dma_rx_push(s, s->buf_len_rx);
1300
1301 mod_timer(&s->rx_timer, jiffies + s->rx_timeout);
1302
1303 spin_unlock_irqrestore(&port->lock, flags);
1304
1305 if (count)
1306 tty_flip_buffer_push(&port->state->port);
1307
1308 schedule_work(&s->work_rx);
1309}
1310
1311static void sci_rx_dma_release(struct sci_port *s, bool enable_pio)
1312{
1313 struct dma_chan *chan = s->chan_rx;
1314 struct uart_port *port = &s->port;
1315
1316 s->chan_rx = NULL;
1317 s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL;
1318 dma_release_channel(chan);
1319 if (sg_dma_address(&s->sg_rx[0]))
1320 dma_free_coherent(port->dev, s->buf_len_rx * 2,
1321 sg_virt(&s->sg_rx[0]), sg_dma_address(&s->sg_rx[0]));
1322 if (enable_pio)
1323 sci_start_rx(port);
1324}
1325
1326static void sci_tx_dma_release(struct sci_port *s, bool enable_pio)
1327{
1328 struct dma_chan *chan = s->chan_tx;
1329 struct uart_port *port = &s->port;
1330
1331 s->chan_tx = NULL;
1332 s->cookie_tx = -EINVAL;
1333 dma_release_channel(chan);
1334 if (enable_pio)
1335 sci_start_tx(port);
1336}
1337
1338static void sci_submit_rx(struct sci_port *s)
1339{
1340 struct dma_chan *chan = s->chan_rx;
1341 int i;
1342
1343 for (i = 0; i < 2; i++) {
1344 struct scatterlist *sg = &s->sg_rx[i];
1345 struct dma_async_tx_descriptor *desc;
1346
1347 desc = dmaengine_prep_slave_sg(chan,
1348 sg, 1, DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
1349
1350 if (desc) {
1351 s->desc_rx[i] = desc;
1352 desc->callback = sci_dma_rx_complete;
1353 desc->callback_param = s;
1354 s->cookie_rx[i] = desc->tx_submit(desc);
1355 }
1356
1357 if (!desc || s->cookie_rx[i] < 0) {
1358 if (i) {
1359 async_tx_ack(s->desc_rx[0]);
1360 s->cookie_rx[0] = -EINVAL;
1361 }
1362 if (desc) {
1363 async_tx_ack(desc);
1364 s->cookie_rx[i] = -EINVAL;
1365 }
1366 dev_warn(s->port.dev,
1367 "failed to re-start DMA, using PIO\n");
1368 sci_rx_dma_release(s, true);
1369 return;
1370 }
1371 dev_dbg(s->port.dev, "%s(): cookie %d to #%d\n",
1372 __func__, s->cookie_rx[i], i);
1373 }
1374
1375 s->active_rx = s->cookie_rx[0];
1376
1377 dma_async_issue_pending(chan);
1378}
1379
1380static void work_fn_rx(struct work_struct *work)
1381{
1382 struct sci_port *s = container_of(work, struct sci_port, work_rx);
1383 struct uart_port *port = &s->port;
1384 struct dma_async_tx_descriptor *desc;
1385 int new;
1386
1387 if (s->active_rx == s->cookie_rx[0]) {
1388 new = 0;
1389 } else if (s->active_rx == s->cookie_rx[1]) {
1390 new = 1;
1391 } else {
1392 dev_err(port->dev, "cookie %d not found!\n", s->active_rx);
1393 return;
1394 }
1395 desc = s->desc_rx[new];
1396
1397 if (dma_async_is_tx_complete(s->chan_rx, s->active_rx, NULL, NULL) !=
1398 DMA_COMPLETE) {
1399 /* Handle incomplete DMA receive */
1400 struct dma_chan *chan = s->chan_rx;
1401 struct shdma_desc *sh_desc = container_of(desc,
1402 struct shdma_desc, async_tx);
1403 unsigned long flags;
1404 int count;
1405
1406 chan->device->device_control(chan, DMA_TERMINATE_ALL, 0);
1407 dev_dbg(port->dev, "Read %zu bytes with cookie %d\n",
1408 sh_desc->partial, sh_desc->cookie);
1409
1410 spin_lock_irqsave(&port->lock, flags);
1411 count = sci_dma_rx_push(s, sh_desc->partial);
1412 spin_unlock_irqrestore(&port->lock, flags);
1413
1414 if (count)
1415 tty_flip_buffer_push(&port->state->port);
1416
1417 sci_submit_rx(s);
1418
1419 return;
1420 }
1421
1422 s->cookie_rx[new] = desc->tx_submit(desc);
1423 if (s->cookie_rx[new] < 0) {
1424 dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
1425 sci_rx_dma_release(s, true);
1426 return;
1427 }
1428
1429 s->active_rx = s->cookie_rx[!new];
1430
1431 dev_dbg(port->dev, "%s: cookie %d #%d, new active #%d\n",
1432 __func__, s->cookie_rx[new], new, s->active_rx);
1433}
1434
1435static void work_fn_tx(struct work_struct *work)
1436{
1437 struct sci_port *s = container_of(work, struct sci_port, work_tx);
1438 struct dma_async_tx_descriptor *desc;
1439 struct dma_chan *chan = s->chan_tx;
1440 struct uart_port *port = &s->port;
1441 struct circ_buf *xmit = &port->state->xmit;
1442 struct scatterlist *sg = &s->sg_tx;
1443
1444 /*
1445 * DMA is idle now.
1446 * Port xmit buffer is already mapped, and it is one page... Just adjust
1447 * offsets and lengths. Since it is a circular buffer, we have to
1448 * transmit till the end, and then the rest. Take the port lock to get a
1449 * consistent xmit buffer state.
1450 */
1451 spin_lock_irq(&port->lock);
1452 sg->offset = xmit->tail & (UART_XMIT_SIZE - 1);
1453 sg_dma_address(sg) = (sg_dma_address(sg) & ~(UART_XMIT_SIZE - 1)) +
1454 sg->offset;
1455 sg_dma_len(sg) = min((int)CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE),
1456 CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE));
1457 spin_unlock_irq(&port->lock);
1458
1459 BUG_ON(!sg_dma_len(sg));
1460
1461 desc = dmaengine_prep_slave_sg(chan,
1462 sg, s->sg_len_tx, DMA_MEM_TO_DEV,
1463 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1464 if (!desc) {
1465 /* switch to PIO */
1466 sci_tx_dma_release(s, true);
1467 return;
1468 }
1469
1470 dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE);
1471
1472 spin_lock_irq(&port->lock);
1473 s->desc_tx = desc;
1474 desc->callback = sci_dma_tx_complete;
1475 desc->callback_param = s;
1476 spin_unlock_irq(&port->lock);
1477 s->cookie_tx = desc->tx_submit(desc);
1478 if (s->cookie_tx < 0) {
1479 dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n");
1480 /* switch to PIO */
1481 sci_tx_dma_release(s, true);
1482 return;
1483 }
1484
1485 dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n",
1486 __func__, xmit->buf, xmit->tail, xmit->head, s->cookie_tx);
1487
1488 dma_async_issue_pending(chan);
1489}
1490#endif
1491
1492static void sci_start_tx(struct uart_port *port)
1493{
1494 struct sci_port *s = to_sci_port(port);
1495 unsigned short ctrl;
1496
1497#ifdef CONFIG_SERIAL_SH_SCI_DMA
1498 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1499 u16 new, scr = serial_port_in(port, SCSCR);
1500 if (s->chan_tx)
1501 new = scr | SCSCR_TDRQE;
1502 else
1503 new = scr & ~SCSCR_TDRQE;
1504 if (new != scr)
1505 serial_port_out(port, SCSCR, new);
1506 }
1507
1508 if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) &&
1509 s->cookie_tx < 0) {
1510 s->cookie_tx = 0;
1511 schedule_work(&s->work_tx);
1512 }
1513#endif
1514
1515 if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1516 /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
1517 ctrl = serial_port_in(port, SCSCR);
1518 serial_port_out(port, SCSCR, ctrl | SCSCR_TIE);
1519 }
1520}
1521
1522static void sci_stop_tx(struct uart_port *port)
1523{
1524 unsigned short ctrl;
1525
1526 /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
1527 ctrl = serial_port_in(port, SCSCR);
1528
1529 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1530 ctrl &= ~SCSCR_TDRQE;
1531
1532 ctrl &= ~SCSCR_TIE;
1533
1534 serial_port_out(port, SCSCR, ctrl);
1535}
1536
1537static void sci_start_rx(struct uart_port *port)
1538{
1539 unsigned short ctrl;
1540
1541 ctrl = serial_port_in(port, SCSCR) | port_rx_irq_mask(port);
1542
1543 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1544 ctrl &= ~SCSCR_RDRQE;
1545
1546 serial_port_out(port, SCSCR, ctrl);
1547}
1548
1549static void sci_stop_rx(struct uart_port *port)
1550{
1551 unsigned short ctrl;
1552
1553 ctrl = serial_port_in(port, SCSCR);
1554
1555 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1556 ctrl &= ~SCSCR_RDRQE;
1557
1558 ctrl &= ~port_rx_irq_mask(port);
1559
1560 serial_port_out(port, SCSCR, ctrl);
1561}
1562
1563static void sci_enable_ms(struct uart_port *port)
1564{
1565 /*
1566 * Not supported by hardware, always a nop.
1567 */
1568}
1569
1570static void sci_break_ctl(struct uart_port *port, int break_state)
1571{
1572 struct sci_port *s = to_sci_port(port);
1573 struct plat_sci_reg *reg = sci_regmap[s->cfg->regtype] + SCSPTR;
1574 unsigned short scscr, scsptr;
1575
1576 /* check wheter the port has SCSPTR */
1577 if (!reg->size) {
1578 /*
1579 * Not supported by hardware. Most parts couple break and rx
1580 * interrupts together, with break detection always enabled.
1581 */
1582 return;
1583 }
1584
1585 scsptr = serial_port_in(port, SCSPTR);
1586 scscr = serial_port_in(port, SCSCR);
1587
1588 if (break_state == -1) {
1589 scsptr = (scsptr | SCSPTR_SPB2IO) & ~SCSPTR_SPB2DT;
1590 scscr &= ~SCSCR_TE;
1591 } else {
1592 scsptr = (scsptr | SCSPTR_SPB2DT) & ~SCSPTR_SPB2IO;
1593 scscr |= SCSCR_TE;
1594 }
1595
1596 serial_port_out(port, SCSPTR, scsptr);
1597 serial_port_out(port, SCSCR, scscr);
1598}
1599
1600#ifdef CONFIG_SERIAL_SH_SCI_DMA
1601static bool filter(struct dma_chan *chan, void *slave)
1602{
1603 struct sh_dmae_slave *param = slave;
1604
1605 dev_dbg(chan->device->dev, "%s: slave ID %d\n",
1606 __func__, param->shdma_slave.slave_id);
1607
1608 chan->private = ¶m->shdma_slave;
1609 return true;
1610}
1611
1612static void rx_timer_fn(unsigned long arg)
1613{
1614 struct sci_port *s = (struct sci_port *)arg;
1615 struct uart_port *port = &s->port;
1616 u16 scr = serial_port_in(port, SCSCR);
1617
1618 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1619 scr &= ~SCSCR_RDRQE;
1620 enable_irq(s->irqs[SCIx_RXI_IRQ]);
1621 }
1622 serial_port_out(port, SCSCR, scr | SCSCR_RIE);
1623 dev_dbg(port->dev, "DMA Rx timed out\n");
1624 schedule_work(&s->work_rx);
1625}
1626
1627static void sci_request_dma(struct uart_port *port)
1628{
1629 struct sci_port *s = to_sci_port(port);
1630 struct sh_dmae_slave *param;
1631 struct dma_chan *chan;
1632 dma_cap_mask_t mask;
1633 int nent;
1634
1635 dev_dbg(port->dev, "%s: port %d\n", __func__, port->line);
1636
1637 if (s->cfg->dma_slave_tx <= 0 || s->cfg->dma_slave_rx <= 0)
1638 return;
1639
1640 dma_cap_zero(mask);
1641 dma_cap_set(DMA_SLAVE, mask);
1642
1643 param = &s->param_tx;
1644
1645 /* Slave ID, e.g., SHDMA_SLAVE_SCIF0_TX */
1646 param->shdma_slave.slave_id = s->cfg->dma_slave_tx;
1647
1648 s->cookie_tx = -EINVAL;
1649 chan = dma_request_channel(mask, filter, param);
1650 dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan);
1651 if (chan) {
1652 s->chan_tx = chan;
1653 sg_init_table(&s->sg_tx, 1);
1654 /* UART circular tx buffer is an aligned page. */
1655 BUG_ON((uintptr_t)port->state->xmit.buf & ~PAGE_MASK);
1656 sg_set_page(&s->sg_tx, virt_to_page(port->state->xmit.buf),
1657 UART_XMIT_SIZE,
1658 (uintptr_t)port->state->xmit.buf & ~PAGE_MASK);
1659 nent = dma_map_sg(port->dev, &s->sg_tx, 1, DMA_TO_DEVICE);
1660 if (!nent)
1661 sci_tx_dma_release(s, false);
1662 else
1663 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n",
1664 __func__,
1665 sg_dma_len(&s->sg_tx), port->state->xmit.buf,
1666 &sg_dma_address(&s->sg_tx));
1667
1668 s->sg_len_tx = nent;
1669
1670 INIT_WORK(&s->work_tx, work_fn_tx);
1671 }
1672
1673 param = &s->param_rx;
1674
1675 /* Slave ID, e.g., SHDMA_SLAVE_SCIF0_RX */
1676 param->shdma_slave.slave_id = s->cfg->dma_slave_rx;
1677
1678 chan = dma_request_channel(mask, filter, param);
1679 dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan);
1680 if (chan) {
1681 dma_addr_t dma[2];
1682 void *buf[2];
1683 int i;
1684
1685 s->chan_rx = chan;
1686
1687 s->buf_len_rx = 2 * max(16, (int)port->fifosize);
1688 buf[0] = dma_alloc_coherent(port->dev, s->buf_len_rx * 2,
1689 &dma[0], GFP_KERNEL);
1690
1691 if (!buf[0]) {
1692 dev_warn(port->dev,
1693 "failed to allocate dma buffer, using PIO\n");
1694 sci_rx_dma_release(s, true);
1695 return;
1696 }
1697
1698 buf[1] = buf[0] + s->buf_len_rx;
1699 dma[1] = dma[0] + s->buf_len_rx;
1700
1701 for (i = 0; i < 2; i++) {
1702 struct scatterlist *sg = &s->sg_rx[i];
1703
1704 sg_init_table(sg, 1);
1705 sg_set_page(sg, virt_to_page(buf[i]), s->buf_len_rx,
1706 (uintptr_t)buf[i] & ~PAGE_MASK);
1707 sg_dma_address(sg) = dma[i];
1708 }
1709
1710 INIT_WORK(&s->work_rx, work_fn_rx);
1711 setup_timer(&s->rx_timer, rx_timer_fn, (unsigned long)s);
1712
1713 sci_submit_rx(s);
1714 }
1715}
1716
1717static void sci_free_dma(struct uart_port *port)
1718{
1719 struct sci_port *s = to_sci_port(port);
1720
1721 if (s->chan_tx)
1722 sci_tx_dma_release(s, false);
1723 if (s->chan_rx)
1724 sci_rx_dma_release(s, false);
1725}
1726#else
1727static inline void sci_request_dma(struct uart_port *port)
1728{
1729}
1730
1731static inline void sci_free_dma(struct uart_port *port)
1732{
1733}
1734#endif
1735
1736static int sci_startup(struct uart_port *port)
1737{
1738 struct sci_port *s = to_sci_port(port);
1739 unsigned long flags;
1740 int ret;
1741
1742 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1743
1744 ret = sci_request_irq(s);
1745 if (unlikely(ret < 0))
1746 return ret;
1747
1748 sci_request_dma(port);
1749
1750 spin_lock_irqsave(&port->lock, flags);
1751 sci_start_tx(port);
1752 sci_start_rx(port);
1753 spin_unlock_irqrestore(&port->lock, flags);
1754
1755 return 0;
1756}
1757
1758static void sci_shutdown(struct uart_port *port)
1759{
1760 struct sci_port *s = to_sci_port(port);
1761 unsigned long flags;
1762
1763 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1764
1765 spin_lock_irqsave(&port->lock, flags);
1766 sci_stop_rx(port);
1767 sci_stop_tx(port);
1768 spin_unlock_irqrestore(&port->lock, flags);
1769
1770 sci_free_dma(port);
1771 sci_free_irq(s);
1772}
1773
1774static unsigned int sci_scbrr_calc(struct sci_port *s, unsigned int bps,
1775 unsigned long freq)
1776{
1777 if (s->sampling_rate)
1778 return DIV_ROUND_CLOSEST(freq, s->sampling_rate * bps) - 1;
1779
1780 /* Warn, but use a safe default */
1781 WARN_ON(1);
1782
1783 return ((freq + 16 * bps) / (32 * bps) - 1);
1784}
1785
1786/* calculate sample rate, BRR, and clock select for HSCIF */
1787static void sci_baud_calc_hscif(unsigned int bps, unsigned long freq,
1788 int *brr, unsigned int *srr,
1789 unsigned int *cks)
1790{
1791 int sr, c, br, err;
1792 int min_err = 1000; /* 100% */
1793
1794 /* Find the combination of sample rate and clock select with the
1795 smallest deviation from the desired baud rate. */
1796 for (sr = 8; sr <= 32; sr++) {
1797 for (c = 0; c <= 3; c++) {
1798 /* integerized formulas from HSCIF documentation */
1799 br = freq / (sr * (1 << (2 * c + 1)) * bps) - 1;
1800 if (br < 0 || br > 255)
1801 continue;
1802 err = freq / ((br + 1) * bps * sr *
1803 (1 << (2 * c + 1)) / 1000) - 1000;
1804 if (min_err > err) {
1805 min_err = err;
1806 *brr = br;
1807 *srr = sr - 1;
1808 *cks = c;
1809 }
1810 }
1811 }
1812
1813 if (min_err == 1000) {
1814 WARN_ON(1);
1815 /* use defaults */
1816 *brr = 255;
1817 *srr = 15;
1818 *cks = 0;
1819 }
1820}
1821
1822static void sci_reset(struct uart_port *port)
1823{
1824 struct plat_sci_reg *reg;
1825 unsigned int status;
1826
1827 do {
1828 status = serial_port_in(port, SCxSR);
1829 } while (!(status & SCxSR_TEND(port)));
1830
1831 serial_port_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
1832
1833 reg = sci_getreg(port, SCFCR);
1834 if (reg->size)
1835 serial_port_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
1836}
1837
1838static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
1839 struct ktermios *old)
1840{
1841 struct sci_port *s = to_sci_port(port);
1842 struct plat_sci_reg *reg;
1843 unsigned int baud, smr_val, max_baud, cks = 0;
1844 int t = -1;
1845 unsigned int srr = 15;
1846
1847 /*
1848 * earlyprintk comes here early on with port->uartclk set to zero.
1849 * the clock framework is not up and running at this point so here
1850 * we assume that 115200 is the maximum baud rate. please note that
1851 * the baud rate is not programmed during earlyprintk - it is assumed
1852 * that the previous boot loader has enabled required clocks and
1853 * setup the baud rate generator hardware for us already.
1854 */
1855 max_baud = port->uartclk ? port->uartclk / 16 : 115200;
1856
1857 baud = uart_get_baud_rate(port, termios, old, 0, max_baud);
1858 if (likely(baud && port->uartclk)) {
1859 if (s->cfg->type == PORT_HSCIF) {
1860 sci_baud_calc_hscif(baud, port->uartclk, &t, &srr,
1861 &cks);
1862 } else {
1863 t = sci_scbrr_calc(s, baud, port->uartclk);
1864 for (cks = 0; t >= 256 && cks <= 3; cks++)
1865 t >>= 2;
1866 }
1867 }
1868
1869 sci_port_enable(s);
1870
1871 sci_reset(port);
1872
1873 smr_val = serial_port_in(port, SCSMR) & 3;
1874
1875 if ((termios->c_cflag & CSIZE) == CS7)
1876 smr_val |= SCSMR_CHR;
1877 if (termios->c_cflag & PARENB)
1878 smr_val |= SCSMR_PE;
1879 if (termios->c_cflag & PARODD)
1880 smr_val |= SCSMR_PE | SCSMR_ODD;
1881 if (termios->c_cflag & CSTOPB)
1882 smr_val |= SCSMR_STOP;
1883
1884 uart_update_timeout(port, termios->c_cflag, baud);
1885
1886 dev_dbg(port->dev, "%s: SMR %x, cks %x, t %x, SCSCR %x\n",
1887 __func__, smr_val, cks, t, s->cfg->scscr);
1888
1889 if (t >= 0) {
1890 serial_port_out(port, SCSMR, (smr_val & ~SCSMR_CKS) | cks);
1891 serial_port_out(port, SCBRR, t);
1892 reg = sci_getreg(port, HSSRR);
1893 if (reg->size)
1894 serial_port_out(port, HSSRR, srr | HSCIF_SRE);
1895 udelay((1000000+(baud-1)) / baud); /* Wait one bit interval */
1896 } else
1897 serial_port_out(port, SCSMR, smr_val);
1898
1899 sci_init_pins(port, termios->c_cflag);
1900
1901 reg = sci_getreg(port, SCFCR);
1902 if (reg->size) {
1903 unsigned short ctrl = serial_port_in(port, SCFCR);
1904
1905 if (s->cfg->capabilities & SCIx_HAVE_RTSCTS) {
1906 if (termios->c_cflag & CRTSCTS)
1907 ctrl |= SCFCR_MCE;
1908 else
1909 ctrl &= ~SCFCR_MCE;
1910 }
1911
1912 /*
1913 * As we've done a sci_reset() above, ensure we don't
1914 * interfere with the FIFOs while toggling MCE. As the
1915 * reset values could still be set, simply mask them out.
1916 */
1917 ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST);
1918
1919 serial_port_out(port, SCFCR, ctrl);
1920 }
1921
1922 serial_port_out(port, SCSCR, s->cfg->scscr);
1923
1924#ifdef CONFIG_SERIAL_SH_SCI_DMA
1925 /*
1926 * Calculate delay for 1.5 DMA buffers: see
1927 * drivers/serial/serial_core.c::uart_update_timeout(). With 10 bits
1928 * (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above function
1929 * calculates 1 jiffie for the data plus 5 jiffies for the "slop(e)."
1930 * Then below we calculate 3 jiffies (12ms) for 1.5 DMA buffers (3 FIFO
1931 * sizes), but it has been found out experimentally, that this is not
1932 * enough: the driver too often needlessly runs on a DMA timeout. 20ms
1933 * as a minimum seem to work perfectly.
1934 */
1935 if (s->chan_rx) {
1936 s->rx_timeout = (port->timeout - HZ / 50) * s->buf_len_rx * 3 /
1937 port->fifosize / 2;
1938 dev_dbg(port->dev, "DMA Rx t-out %ums, tty t-out %u jiffies\n",
1939 s->rx_timeout * 1000 / HZ, port->timeout);
1940 if (s->rx_timeout < msecs_to_jiffies(20))
1941 s->rx_timeout = msecs_to_jiffies(20);
1942 }
1943#endif
1944
1945 if ((termios->c_cflag & CREAD) != 0)
1946 sci_start_rx(port);
1947
1948 sci_port_disable(s);
1949}
1950
1951static void sci_pm(struct uart_port *port, unsigned int state,
1952 unsigned int oldstate)
1953{
1954 struct sci_port *sci_port = to_sci_port(port);
1955
1956 switch (state) {
1957 case UART_PM_STATE_OFF:
1958 sci_port_disable(sci_port);
1959 break;
1960 default:
1961 sci_port_enable(sci_port);
1962 break;
1963 }
1964}
1965
1966static const char *sci_type(struct uart_port *port)
1967{
1968 switch (port->type) {
1969 case PORT_IRDA:
1970 return "irda";
1971 case PORT_SCI:
1972 return "sci";
1973 case PORT_SCIF:
1974 return "scif";
1975 case PORT_SCIFA:
1976 return "scifa";
1977 case PORT_SCIFB:
1978 return "scifb";
1979 case PORT_HSCIF:
1980 return "hscif";
1981 }
1982
1983 return NULL;
1984}
1985
1986static inline unsigned long sci_port_size(struct uart_port *port)
1987{
1988 /*
1989 * Pick an arbitrary size that encapsulates all of the base
1990 * registers by default. This can be optimized later, or derived
1991 * from platform resource data at such a time that ports begin to
1992 * behave more erratically.
1993 */
1994 if (port->type == PORT_HSCIF)
1995 return 96;
1996 else
1997 return 64;
1998}
1999
2000static int sci_remap_port(struct uart_port *port)
2001{
2002 unsigned long size = sci_port_size(port);
2003
2004 /*
2005 * Nothing to do if there's already an established membase.
2006 */
2007 if (port->membase)
2008 return 0;
2009
2010 if (port->flags & UPF_IOREMAP) {
2011 port->membase = ioremap_nocache(port->mapbase, size);
2012 if (unlikely(!port->membase)) {
2013 dev_err(port->dev, "can't remap port#%d\n", port->line);
2014 return -ENXIO;
2015 }
2016 } else {
2017 /*
2018 * For the simple (and majority of) cases where we don't
2019 * need to do any remapping, just cast the cookie
2020 * directly.
2021 */
2022 port->membase = (void __iomem *)(uintptr_t)port->mapbase;
2023 }
2024
2025 return 0;
2026}
2027
2028static void sci_release_port(struct uart_port *port)
2029{
2030 if (port->flags & UPF_IOREMAP) {
2031 iounmap(port->membase);
2032 port->membase = NULL;
2033 }
2034
2035 release_mem_region(port->mapbase, sci_port_size(port));
2036}
2037
2038static int sci_request_port(struct uart_port *port)
2039{
2040 unsigned long size = sci_port_size(port);
2041 struct resource *res;
2042 int ret;
2043
2044 res = request_mem_region(port->mapbase, size, dev_name(port->dev));
2045 if (unlikely(res == NULL))
2046 return -EBUSY;
2047
2048 ret = sci_remap_port(port);
2049 if (unlikely(ret != 0)) {
2050 release_resource(res);
2051 return ret;
2052 }
2053
2054 return 0;
2055}
2056
2057static void sci_config_port(struct uart_port *port, int flags)
2058{
2059 if (flags & UART_CONFIG_TYPE) {
2060 struct sci_port *sport = to_sci_port(port);
2061
2062 port->type = sport->cfg->type;
2063 sci_request_port(port);
2064 }
2065}
2066
2067static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
2068{
2069 if (ser->baud_base < 2400)
2070 /* No paper tape reader for Mitch.. */
2071 return -EINVAL;
2072
2073 return 0;
2074}
2075
2076static struct uart_ops sci_uart_ops = {
2077 .tx_empty = sci_tx_empty,
2078 .set_mctrl = sci_set_mctrl,
2079 .get_mctrl = sci_get_mctrl,
2080 .start_tx = sci_start_tx,
2081 .stop_tx = sci_stop_tx,
2082 .stop_rx = sci_stop_rx,
2083 .enable_ms = sci_enable_ms,
2084 .break_ctl = sci_break_ctl,
2085 .startup = sci_startup,
2086 .shutdown = sci_shutdown,
2087 .set_termios = sci_set_termios,
2088 .pm = sci_pm,
2089 .type = sci_type,
2090 .release_port = sci_release_port,
2091 .request_port = sci_request_port,
2092 .config_port = sci_config_port,
2093 .verify_port = sci_verify_port,
2094#ifdef CONFIG_CONSOLE_POLL
2095 .poll_get_char = sci_poll_get_char,
2096 .poll_put_char = sci_poll_put_char,
2097#endif
2098};
2099
2100static int sci_init_single(struct platform_device *dev,
2101 struct sci_port *sci_port, unsigned int index,
2102 struct plat_sci_port *p, bool early)
2103{
2104 struct uart_port *port = &sci_port->port;
2105 const struct resource *res;
2106 unsigned int sampling_rate;
2107 unsigned int i;
2108 int ret;
2109
2110 sci_port->cfg = p;
2111
2112 port->ops = &sci_uart_ops;
2113 port->iotype = UPIO_MEM;
2114 port->line = index;
2115
2116 res = platform_get_resource(dev, IORESOURCE_MEM, 0);
2117 if (res == NULL)
2118 return -ENOMEM;
2119
2120 port->mapbase = res->start;
2121
2122 for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i)
2123 sci_port->irqs[i] = platform_get_irq(dev, i);
2124
2125 /* The SCI generates several interrupts. They can be muxed together or
2126 * connected to different interrupt lines. In the muxed case only one
2127 * interrupt resource is specified. In the non-muxed case three or four
2128 * interrupt resources are specified, as the BRI interrupt is optional.
2129 */
2130 if (sci_port->irqs[0] < 0)
2131 return -ENXIO;
2132
2133 if (sci_port->irqs[1] < 0) {
2134 sci_port->irqs[1] = sci_port->irqs[0];
2135 sci_port->irqs[2] = sci_port->irqs[0];
2136 sci_port->irqs[3] = sci_port->irqs[0];
2137 }
2138
2139 if (p->regtype == SCIx_PROBE_REGTYPE) {
2140 ret = sci_probe_regmap(p);
2141 if (unlikely(ret))
2142 return ret;
2143 }
2144
2145 switch (p->type) {
2146 case PORT_SCIFB:
2147 port->fifosize = 256;
2148 sci_port->overrun_bit = 9;
2149 sampling_rate = 16;
2150 break;
2151 case PORT_HSCIF:
2152 port->fifosize = 128;
2153 sampling_rate = 0;
2154 sci_port->overrun_bit = 0;
2155 break;
2156 case PORT_SCIFA:
2157 port->fifosize = 64;
2158 sci_port->overrun_bit = 9;
2159 sampling_rate = 16;
2160 break;
2161 case PORT_SCIF:
2162 port->fifosize = 16;
2163 if (p->regtype == SCIx_SH7705_SCIF_REGTYPE) {
2164 sci_port->overrun_bit = 9;
2165 sampling_rate = 16;
2166 } else {
2167 sci_port->overrun_bit = 0;
2168 sampling_rate = 32;
2169 }
2170 break;
2171 default:
2172 port->fifosize = 1;
2173 sci_port->overrun_bit = 5;
2174 sampling_rate = 32;
2175 break;
2176 }
2177
2178 /* SCIFA on sh7723 and sh7724 need a custom sampling rate that doesn't
2179 * match the SoC datasheet, this should be investigated. Let platform
2180 * data override the sampling rate for now.
2181 */
2182 sci_port->sampling_rate = p->sampling_rate ? p->sampling_rate
2183 : sampling_rate;
2184
2185 if (!early) {
2186 sci_port->iclk = clk_get(&dev->dev, "sci_ick");
2187 if (IS_ERR(sci_port->iclk)) {
2188 sci_port->iclk = clk_get(&dev->dev, "peripheral_clk");
2189 if (IS_ERR(sci_port->iclk)) {
2190 dev_err(&dev->dev, "can't get iclk\n");
2191 return PTR_ERR(sci_port->iclk);
2192 }
2193 }
2194
2195 /*
2196 * The function clock is optional, ignore it if we can't
2197 * find it.
2198 */
2199 sci_port->fclk = clk_get(&dev->dev, "sci_fck");
2200 if (IS_ERR(sci_port->fclk))
2201 sci_port->fclk = NULL;
2202
2203 port->dev = &dev->dev;
2204
2205 pm_runtime_enable(&dev->dev);
2206 }
2207
2208 sci_port->break_timer.data = (unsigned long)sci_port;
2209 sci_port->break_timer.function = sci_break_timer;
2210 init_timer(&sci_port->break_timer);
2211
2212 /*
2213 * Establish some sensible defaults for the error detection.
2214 */
2215 sci_port->error_mask = (p->type == PORT_SCI) ?
2216 SCI_DEFAULT_ERROR_MASK : SCIF_DEFAULT_ERROR_MASK;
2217
2218 /*
2219 * Establish sensible defaults for the overrun detection, unless
2220 * the part has explicitly disabled support for it.
2221 */
2222
2223 /*
2224 * Make the error mask inclusive of overrun detection, if
2225 * supported.
2226 */
2227 sci_port->error_mask |= 1 << sci_port->overrun_bit;
2228
2229 port->type = p->type;
2230 port->flags = UPF_FIXED_PORT | p->flags;
2231 port->regshift = p->regshift;
2232
2233 /*
2234 * The UART port needs an IRQ value, so we peg this to the RX IRQ
2235 * for the multi-IRQ ports, which is where we are primarily
2236 * concerned with the shutdown path synchronization.
2237 *
2238 * For the muxed case there's nothing more to do.
2239 */
2240 port->irq = sci_port->irqs[SCIx_RXI_IRQ];
2241 port->irqflags = 0;
2242
2243 port->serial_in = sci_serial_in;
2244 port->serial_out = sci_serial_out;
2245
2246 if (p->dma_slave_tx > 0 && p->dma_slave_rx > 0)
2247 dev_dbg(port->dev, "DMA tx %d, rx %d\n",
2248 p->dma_slave_tx, p->dma_slave_rx);
2249
2250 return 0;
2251}
2252
2253static void sci_cleanup_single(struct sci_port *port)
2254{
2255 clk_put(port->iclk);
2256 clk_put(port->fclk);
2257
2258 pm_runtime_disable(port->port.dev);
2259}
2260
2261#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
2262static void serial_console_putchar(struct uart_port *port, int ch)
2263{
2264 sci_poll_put_char(port, ch);
2265}
2266
2267/*
2268 * Print a string to the serial port trying not to disturb
2269 * any possible real use of the port...
2270 */
2271static void serial_console_write(struct console *co, const char *s,
2272 unsigned count)
2273{
2274 struct sci_port *sci_port = &sci_ports[co->index];
2275 struct uart_port *port = &sci_port->port;
2276 unsigned short bits, ctrl;
2277 unsigned long flags;
2278 int locked = 1;
2279
2280 local_irq_save(flags);
2281 if (port->sysrq)
2282 locked = 0;
2283 else if (oops_in_progress)
2284 locked = spin_trylock(&port->lock);
2285 else
2286 spin_lock(&port->lock);
2287
2288 /* first save the SCSCR then disable the interrupts */
2289 ctrl = serial_port_in(port, SCSCR);
2290 serial_port_out(port, SCSCR, sci_port->cfg->scscr);
2291
2292 uart_console_write(port, s, count, serial_console_putchar);
2293
2294 /* wait until fifo is empty and last bit has been transmitted */
2295 bits = SCxSR_TDxE(port) | SCxSR_TEND(port);
2296 while ((serial_port_in(port, SCxSR) & bits) != bits)
2297 cpu_relax();
2298
2299 /* restore the SCSCR */
2300 serial_port_out(port, SCSCR, ctrl);
2301
2302 if (locked)
2303 spin_unlock(&port->lock);
2304 local_irq_restore(flags);
2305}
2306
2307static int serial_console_setup(struct console *co, char *options)
2308{
2309 struct sci_port *sci_port;
2310 struct uart_port *port;
2311 int baud = 115200;
2312 int bits = 8;
2313 int parity = 'n';
2314 int flow = 'n';
2315 int ret;
2316
2317 /*
2318 * Refuse to handle any bogus ports.
2319 */
2320 if (co->index < 0 || co->index >= SCI_NPORTS)
2321 return -ENODEV;
2322
2323 sci_port = &sci_ports[co->index];
2324 port = &sci_port->port;
2325
2326 /*
2327 * Refuse to handle uninitialized ports.
2328 */
2329 if (!port->ops)
2330 return -ENODEV;
2331
2332 ret = sci_remap_port(port);
2333 if (unlikely(ret != 0))
2334 return ret;
2335
2336 if (options)
2337 uart_parse_options(options, &baud, &parity, &bits, &flow);
2338
2339 return uart_set_options(port, co, baud, parity, bits, flow);
2340}
2341
2342static struct console serial_console = {
2343 .name = "ttySC",
2344 .device = uart_console_device,
2345 .write = serial_console_write,
2346 .setup = serial_console_setup,
2347 .flags = CON_PRINTBUFFER,
2348 .index = -1,
2349 .data = &sci_uart_driver,
2350};
2351
2352static struct console early_serial_console = {
2353 .name = "early_ttySC",
2354 .write = serial_console_write,
2355 .flags = CON_PRINTBUFFER,
2356 .index = -1,
2357};
2358
2359static char early_serial_buf[32];
2360
2361static int sci_probe_earlyprintk(struct platform_device *pdev)
2362{
2363 struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev);
2364
2365 if (early_serial_console.data)
2366 return -EEXIST;
2367
2368 early_serial_console.index = pdev->id;
2369
2370 sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true);
2371
2372 serial_console_setup(&early_serial_console, early_serial_buf);
2373
2374 if (!strstr(early_serial_buf, "keep"))
2375 early_serial_console.flags |= CON_BOOT;
2376
2377 register_console(&early_serial_console);
2378 return 0;
2379}
2380
2381#define SCI_CONSOLE (&serial_console)
2382
2383#else
2384static inline int sci_probe_earlyprintk(struct platform_device *pdev)
2385{
2386 return -EINVAL;
2387}
2388
2389#define SCI_CONSOLE NULL
2390
2391#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
2392
2393static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized";
2394
2395static struct uart_driver sci_uart_driver = {
2396 .owner = THIS_MODULE,
2397 .driver_name = "sci",
2398 .dev_name = "ttySC",
2399 .major = SCI_MAJOR,
2400 .minor = SCI_MINOR_START,
2401 .nr = SCI_NPORTS,
2402 .cons = SCI_CONSOLE,
2403};
2404
2405static int sci_remove(struct platform_device *dev)
2406{
2407 struct sci_port *port = platform_get_drvdata(dev);
2408
2409 cpufreq_unregister_notifier(&port->freq_transition,
2410 CPUFREQ_TRANSITION_NOTIFIER);
2411
2412 uart_remove_one_port(&sci_uart_driver, &port->port);
2413
2414 sci_cleanup_single(port);
2415
2416 return 0;
2417}
2418
2419struct sci_port_info {
2420 unsigned int type;
2421 unsigned int regtype;
2422};
2423
2424static const struct of_device_id of_sci_match[] = {
2425 {
2426 .compatible = "renesas,scif",
2427 .data = &(const struct sci_port_info) {
2428 .type = PORT_SCIF,
2429 .regtype = SCIx_SH4_SCIF_REGTYPE,
2430 },
2431 }, {
2432 .compatible = "renesas,scifa",
2433 .data = &(const struct sci_port_info) {
2434 .type = PORT_SCIFA,
2435 .regtype = SCIx_SCIFA_REGTYPE,
2436 },
2437 }, {
2438 .compatible = "renesas,scifb",
2439 .data = &(const struct sci_port_info) {
2440 .type = PORT_SCIFB,
2441 .regtype = SCIx_SCIFB_REGTYPE,
2442 },
2443 }, {
2444 .compatible = "renesas,hscif",
2445 .data = &(const struct sci_port_info) {
2446 .type = PORT_HSCIF,
2447 .regtype = SCIx_HSCIF_REGTYPE,
2448 },
2449 }, {
2450 /* Terminator */
2451 },
2452};
2453MODULE_DEVICE_TABLE(of, of_sci_match);
2454
2455static struct plat_sci_port *
2456sci_parse_dt(struct platform_device *pdev, unsigned int *dev_id)
2457{
2458 struct device_node *np = pdev->dev.of_node;
2459 const struct of_device_id *match;
2460 const struct sci_port_info *info;
2461 struct plat_sci_port *p;
2462 int id;
2463
2464 if (!IS_ENABLED(CONFIG_OF) || !np)
2465 return NULL;
2466
2467 match = of_match_node(of_sci_match, pdev->dev.of_node);
2468 if (!match)
2469 return NULL;
2470
2471 info = match->data;
2472
2473 p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
2474 if (!p) {
2475 dev_err(&pdev->dev, "failed to allocate DT config data\n");
2476 return NULL;
2477 }
2478
2479 /* Get the line number for the aliases node. */
2480 id = of_alias_get_id(np, "serial");
2481 if (id < 0) {
2482 dev_err(&pdev->dev, "failed to get alias id (%d)\n", id);
2483 return NULL;
2484 }
2485
2486 *dev_id = id;
2487
2488 p->flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
2489 p->type = info->type;
2490 p->regtype = info->regtype;
2491 p->scscr = SCSCR_RE | SCSCR_TE;
2492
2493 return p;
2494}
2495
2496static int sci_probe_single(struct platform_device *dev,
2497 unsigned int index,
2498 struct plat_sci_port *p,
2499 struct sci_port *sciport)
2500{
2501 int ret;
2502
2503 /* Sanity check */
2504 if (unlikely(index >= SCI_NPORTS)) {
2505 dev_notice(&dev->dev, "Attempting to register port %d when only %d are available\n",
2506 index+1, SCI_NPORTS);
2507 dev_notice(&dev->dev, "Consider bumping CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
2508 return -EINVAL;
2509 }
2510
2511 ret = sci_init_single(dev, sciport, index, p, false);
2512 if (ret)
2513 return ret;
2514
2515 ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
2516 if (ret) {
2517 sci_cleanup_single(sciport);
2518 return ret;
2519 }
2520
2521 return 0;
2522}
2523
2524static int sci_probe(struct platform_device *dev)
2525{
2526 struct plat_sci_port *p;
2527 struct sci_port *sp;
2528 unsigned int dev_id;
2529 int ret;
2530
2531 /*
2532 * If we've come here via earlyprintk initialization, head off to
2533 * the special early probe. We don't have sufficient device state
2534 * to make it beyond this yet.
2535 */
2536 if (is_early_platform_device(dev))
2537 return sci_probe_earlyprintk(dev);
2538
2539 if (dev->dev.of_node) {
2540 p = sci_parse_dt(dev, &dev_id);
2541 if (p == NULL)
2542 return -EINVAL;
2543 } else {
2544 p = dev->dev.platform_data;
2545 if (p == NULL) {
2546 dev_err(&dev->dev, "no platform data supplied\n");
2547 return -EINVAL;
2548 }
2549
2550 dev_id = dev->id;
2551 }
2552
2553 sp = &sci_ports[dev_id];
2554 platform_set_drvdata(dev, sp);
2555
2556 ret = sci_probe_single(dev, dev_id, p, sp);
2557 if (ret)
2558 return ret;
2559
2560 sp->freq_transition.notifier_call = sci_notifier;
2561
2562 ret = cpufreq_register_notifier(&sp->freq_transition,
2563 CPUFREQ_TRANSITION_NOTIFIER);
2564 if (unlikely(ret < 0)) {
2565 uart_remove_one_port(&sci_uart_driver, &sp->port);
2566 sci_cleanup_single(sp);
2567 return ret;
2568 }
2569
2570#ifdef CONFIG_SH_STANDARD_BIOS
2571 sh_bios_gdb_detach();
2572#endif
2573
2574 return 0;
2575}
2576
2577static int sci_suspend(struct device *dev)
2578{
2579 struct sci_port *sport = dev_get_drvdata(dev);
2580
2581 if (sport)
2582 uart_suspend_port(&sci_uart_driver, &sport->port);
2583
2584 return 0;
2585}
2586
2587static int sci_resume(struct device *dev)
2588{
2589 struct sci_port *sport = dev_get_drvdata(dev);
2590
2591 if (sport)
2592 uart_resume_port(&sci_uart_driver, &sport->port);
2593
2594 return 0;
2595}
2596
2597static const struct dev_pm_ops sci_dev_pm_ops = {
2598 .suspend = sci_suspend,
2599 .resume = sci_resume,
2600};
2601
2602static struct platform_driver sci_driver = {
2603 .probe = sci_probe,
2604 .remove = sci_remove,
2605 .driver = {
2606 .name = "sh-sci",
2607 .owner = THIS_MODULE,
2608 .pm = &sci_dev_pm_ops,
2609 .of_match_table = of_match_ptr(of_sci_match),
2610 },
2611};
2612
2613static int __init sci_init(void)
2614{
2615 int ret;
2616
2617 pr_info("%s\n", banner);
2618
2619 ret = uart_register_driver(&sci_uart_driver);
2620 if (likely(ret == 0)) {
2621 ret = platform_driver_register(&sci_driver);
2622 if (unlikely(ret))
2623 uart_unregister_driver(&sci_uart_driver);
2624 }
2625
2626 return ret;
2627}
2628
2629static void __exit sci_exit(void)
2630{
2631 platform_driver_unregister(&sci_driver);
2632 uart_unregister_driver(&sci_uart_driver);
2633}
2634
2635#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
2636early_platform_init_buffer("earlyprintk", &sci_driver,
2637 early_serial_buf, ARRAY_SIZE(early_serial_buf));
2638#endif
2639module_init(sci_init);
2640module_exit(sci_exit);
2641
2642MODULE_LICENSE("GPL");
2643MODULE_ALIAS("platform:sh-sci");
2644MODULE_AUTHOR("Paul Mundt");
2645MODULE_DESCRIPTION("SuperH (H)SCI(F) serial driver");