Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
4 *
5 * Copyright (C) 2002 - 2011 Paul Mundt
6 * Copyright (C) 2015 Glider bvba
7 * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
8 *
9 * based off of the old drivers/char/sh-sci.c by:
10 *
11 * Copyright (C) 1999, 2000 Niibe Yutaka
12 * Copyright (C) 2000 Sugioka Toshinobu
13 * Modified to support multiple serial ports. Stuart Menefy (May 2000).
14 * Modified to support SecureEdge. David McCullough (2002)
15 * Modified to support SH7300 SCIF. Takashi Kusuda (Jun 2003).
16 * Removed SH7300 support (Jul 2007).
17 */
18#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
19#define SUPPORT_SYSRQ
20#endif
21
22#undef DEBUG
23
24#include <linux/clk.h>
25#include <linux/console.h>
26#include <linux/ctype.h>
27#include <linux/cpufreq.h>
28#include <linux/delay.h>
29#include <linux/dmaengine.h>
30#include <linux/dma-mapping.h>
31#include <linux/err.h>
32#include <linux/errno.h>
33#include <linux/init.h>
34#include <linux/interrupt.h>
35#include <linux/ioport.h>
36#include <linux/ktime.h>
37#include <linux/major.h>
38#include <linux/module.h>
39#include <linux/mm.h>
40#include <linux/of.h>
41#include <linux/of_device.h>
42#include <linux/platform_device.h>
43#include <linux/pm_runtime.h>
44#include <linux/scatterlist.h>
45#include <linux/serial.h>
46#include <linux/serial_sci.h>
47#include <linux/sh_dma.h>
48#include <linux/slab.h>
49#include <linux/string.h>
50#include <linux/sysrq.h>
51#include <linux/timer.h>
52#include <linux/tty.h>
53#include <linux/tty_flip.h>
54
55#ifdef CONFIG_SUPERH
56#include <asm/sh_bios.h>
57#endif
58
59#include "serial_mctrl_gpio.h"
60#include "sh-sci.h"
61
62/* Offsets into the sci_port->irqs array */
63enum {
64 SCIx_ERI_IRQ,
65 SCIx_RXI_IRQ,
66 SCIx_TXI_IRQ,
67 SCIx_BRI_IRQ,
68 SCIx_DRI_IRQ,
69 SCIx_TEI_IRQ,
70 SCIx_NR_IRQS,
71
72 SCIx_MUX_IRQ = SCIx_NR_IRQS, /* special case */
73};
74
75#define SCIx_IRQ_IS_MUXED(port) \
76 ((port)->irqs[SCIx_ERI_IRQ] == \
77 (port)->irqs[SCIx_RXI_IRQ]) || \
78 ((port)->irqs[SCIx_ERI_IRQ] && \
79 ((port)->irqs[SCIx_RXI_IRQ] < 0))
80
81enum SCI_CLKS {
82 SCI_FCK, /* Functional Clock */
83 SCI_SCK, /* Optional External Clock */
84 SCI_BRG_INT, /* Optional BRG Internal Clock Source */
85 SCI_SCIF_CLK, /* Optional BRG External Clock Source */
86 SCI_NUM_CLKS
87};
88
89/* Bit x set means sampling rate x + 1 is supported */
90#define SCI_SR(x) BIT((x) - 1)
91#define SCI_SR_RANGE(x, y) GENMASK((y) - 1, (x) - 1)
92
93#define SCI_SR_SCIFAB SCI_SR(5) | SCI_SR(7) | SCI_SR(11) | \
94 SCI_SR(13) | SCI_SR(16) | SCI_SR(17) | \
95 SCI_SR(19) | SCI_SR(27)
96
97#define min_sr(_port) ffs((_port)->sampling_rate_mask)
98#define max_sr(_port) fls((_port)->sampling_rate_mask)
99
100/* Iterate over all supported sampling rates, from high to low */
101#define for_each_sr(_sr, _port) \
102 for ((_sr) = max_sr(_port); (_sr) >= min_sr(_port); (_sr)--) \
103 if ((_port)->sampling_rate_mask & SCI_SR((_sr)))
104
105struct plat_sci_reg {
106 u8 offset, size;
107};
108
109struct sci_port_params {
110 const struct plat_sci_reg regs[SCIx_NR_REGS];
111 unsigned int fifosize;
112 unsigned int overrun_reg;
113 unsigned int overrun_mask;
114 unsigned int sampling_rate_mask;
115 unsigned int error_mask;
116 unsigned int error_clear;
117};
118
119struct sci_port {
120 struct uart_port port;
121
122 /* Platform configuration */
123 const struct sci_port_params *params;
124 const struct plat_sci_port *cfg;
125 unsigned int sampling_rate_mask;
126 resource_size_t reg_size;
127 struct mctrl_gpios *gpios;
128
129 /* Clocks */
130 struct clk *clks[SCI_NUM_CLKS];
131 unsigned long clk_rates[SCI_NUM_CLKS];
132
133 int irqs[SCIx_NR_IRQS];
134 char *irqstr[SCIx_NR_IRQS];
135
136 struct dma_chan *chan_tx;
137 struct dma_chan *chan_rx;
138
139#ifdef CONFIG_SERIAL_SH_SCI_DMA
140 struct dma_chan *chan_tx_saved;
141 struct dma_chan *chan_rx_saved;
142 dma_cookie_t cookie_tx;
143 dma_cookie_t cookie_rx[2];
144 dma_cookie_t active_rx;
145 dma_addr_t tx_dma_addr;
146 unsigned int tx_dma_len;
147 struct scatterlist sg_rx[2];
148 void *rx_buf[2];
149 size_t buf_len_rx;
150 struct work_struct work_tx;
151 struct hrtimer rx_timer;
152 unsigned int rx_timeout; /* microseconds */
153#endif
154 unsigned int rx_frame;
155 int rx_trigger;
156 struct timer_list rx_fifo_timer;
157 int rx_fifo_timeout;
158 u16 hscif_tot;
159
160 bool has_rtscts;
161 bool autorts;
162};
163
164#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS
165
166static struct sci_port sci_ports[SCI_NPORTS];
167static unsigned long sci_ports_in_use;
168static struct uart_driver sci_uart_driver;
169
170static inline struct sci_port *
171to_sci_port(struct uart_port *uart)
172{
173 return container_of(uart, struct sci_port, port);
174}
175
176static const struct sci_port_params sci_port_params[SCIx_NR_REGTYPES] = {
177 /*
178 * Common SCI definitions, dependent on the port's regshift
179 * value.
180 */
181 [SCIx_SCI_REGTYPE] = {
182 .regs = {
183 [SCSMR] = { 0x00, 8 },
184 [SCBRR] = { 0x01, 8 },
185 [SCSCR] = { 0x02, 8 },
186 [SCxTDR] = { 0x03, 8 },
187 [SCxSR] = { 0x04, 8 },
188 [SCxRDR] = { 0x05, 8 },
189 },
190 .fifosize = 1,
191 .overrun_reg = SCxSR,
192 .overrun_mask = SCI_ORER,
193 .sampling_rate_mask = SCI_SR(32),
194 .error_mask = SCI_DEFAULT_ERROR_MASK | SCI_ORER,
195 .error_clear = SCI_ERROR_CLEAR & ~SCI_ORER,
196 },
197
198 /*
199 * Common definitions for legacy IrDA ports.
200 */
201 [SCIx_IRDA_REGTYPE] = {
202 .regs = {
203 [SCSMR] = { 0x00, 8 },
204 [SCBRR] = { 0x02, 8 },
205 [SCSCR] = { 0x04, 8 },
206 [SCxTDR] = { 0x06, 8 },
207 [SCxSR] = { 0x08, 16 },
208 [SCxRDR] = { 0x0a, 8 },
209 [SCFCR] = { 0x0c, 8 },
210 [SCFDR] = { 0x0e, 16 },
211 },
212 .fifosize = 1,
213 .overrun_reg = SCxSR,
214 .overrun_mask = SCI_ORER,
215 .sampling_rate_mask = SCI_SR(32),
216 .error_mask = SCI_DEFAULT_ERROR_MASK | SCI_ORER,
217 .error_clear = SCI_ERROR_CLEAR & ~SCI_ORER,
218 },
219
220 /*
221 * Common SCIFA definitions.
222 */
223 [SCIx_SCIFA_REGTYPE] = {
224 .regs = {
225 [SCSMR] = { 0x00, 16 },
226 [SCBRR] = { 0x04, 8 },
227 [SCSCR] = { 0x08, 16 },
228 [SCxTDR] = { 0x20, 8 },
229 [SCxSR] = { 0x14, 16 },
230 [SCxRDR] = { 0x24, 8 },
231 [SCFCR] = { 0x18, 16 },
232 [SCFDR] = { 0x1c, 16 },
233 [SCPCR] = { 0x30, 16 },
234 [SCPDR] = { 0x34, 16 },
235 },
236 .fifosize = 64,
237 .overrun_reg = SCxSR,
238 .overrun_mask = SCIFA_ORER,
239 .sampling_rate_mask = SCI_SR_SCIFAB,
240 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER,
241 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER,
242 },
243
244 /*
245 * Common SCIFB definitions.
246 */
247 [SCIx_SCIFB_REGTYPE] = {
248 .regs = {
249 [SCSMR] = { 0x00, 16 },
250 [SCBRR] = { 0x04, 8 },
251 [SCSCR] = { 0x08, 16 },
252 [SCxTDR] = { 0x40, 8 },
253 [SCxSR] = { 0x14, 16 },
254 [SCxRDR] = { 0x60, 8 },
255 [SCFCR] = { 0x18, 16 },
256 [SCTFDR] = { 0x38, 16 },
257 [SCRFDR] = { 0x3c, 16 },
258 [SCPCR] = { 0x30, 16 },
259 [SCPDR] = { 0x34, 16 },
260 },
261 .fifosize = 256,
262 .overrun_reg = SCxSR,
263 .overrun_mask = SCIFA_ORER,
264 .sampling_rate_mask = SCI_SR_SCIFAB,
265 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER,
266 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER,
267 },
268
269 /*
270 * Common SH-2(A) SCIF definitions for ports with FIFO data
271 * count registers.
272 */
273 [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
274 .regs = {
275 [SCSMR] = { 0x00, 16 },
276 [SCBRR] = { 0x04, 8 },
277 [SCSCR] = { 0x08, 16 },
278 [SCxTDR] = { 0x0c, 8 },
279 [SCxSR] = { 0x10, 16 },
280 [SCxRDR] = { 0x14, 8 },
281 [SCFCR] = { 0x18, 16 },
282 [SCFDR] = { 0x1c, 16 },
283 [SCSPTR] = { 0x20, 16 },
284 [SCLSR] = { 0x24, 16 },
285 },
286 .fifosize = 16,
287 .overrun_reg = SCLSR,
288 .overrun_mask = SCLSR_ORER,
289 .sampling_rate_mask = SCI_SR(32),
290 .error_mask = SCIF_DEFAULT_ERROR_MASK,
291 .error_clear = SCIF_ERROR_CLEAR,
292 },
293
294 /*
295 * The "SCIFA" that is in RZ/T and RZ/A2.
296 * It looks like a normal SCIF with FIFO data, but with a
297 * compressed address space. Also, the break out of interrupts
298 * are different: ERI/BRI, RXI, TXI, TEI, DRI.
299 */
300 [SCIx_RZ_SCIFA_REGTYPE] = {
301 .regs = {
302 [SCSMR] = { 0x00, 16 },
303 [SCBRR] = { 0x02, 8 },
304 [SCSCR] = { 0x04, 16 },
305 [SCxTDR] = { 0x06, 8 },
306 [SCxSR] = { 0x08, 16 },
307 [SCxRDR] = { 0x0A, 8 },
308 [SCFCR] = { 0x0C, 16 },
309 [SCFDR] = { 0x0E, 16 },
310 [SCSPTR] = { 0x10, 16 },
311 [SCLSR] = { 0x12, 16 },
312 },
313 .fifosize = 16,
314 .overrun_reg = SCLSR,
315 .overrun_mask = SCLSR_ORER,
316 .sampling_rate_mask = SCI_SR(32),
317 .error_mask = SCIF_DEFAULT_ERROR_MASK,
318 .error_clear = SCIF_ERROR_CLEAR,
319 },
320
321 /*
322 * Common SH-3 SCIF definitions.
323 */
324 [SCIx_SH3_SCIF_REGTYPE] = {
325 .regs = {
326 [SCSMR] = { 0x00, 8 },
327 [SCBRR] = { 0x02, 8 },
328 [SCSCR] = { 0x04, 8 },
329 [SCxTDR] = { 0x06, 8 },
330 [SCxSR] = { 0x08, 16 },
331 [SCxRDR] = { 0x0a, 8 },
332 [SCFCR] = { 0x0c, 8 },
333 [SCFDR] = { 0x0e, 16 },
334 },
335 .fifosize = 16,
336 .overrun_reg = SCLSR,
337 .overrun_mask = SCLSR_ORER,
338 .sampling_rate_mask = SCI_SR(32),
339 .error_mask = SCIF_DEFAULT_ERROR_MASK,
340 .error_clear = SCIF_ERROR_CLEAR,
341 },
342
343 /*
344 * Common SH-4(A) SCIF(B) definitions.
345 */
346 [SCIx_SH4_SCIF_REGTYPE] = {
347 .regs = {
348 [SCSMR] = { 0x00, 16 },
349 [SCBRR] = { 0x04, 8 },
350 [SCSCR] = { 0x08, 16 },
351 [SCxTDR] = { 0x0c, 8 },
352 [SCxSR] = { 0x10, 16 },
353 [SCxRDR] = { 0x14, 8 },
354 [SCFCR] = { 0x18, 16 },
355 [SCFDR] = { 0x1c, 16 },
356 [SCSPTR] = { 0x20, 16 },
357 [SCLSR] = { 0x24, 16 },
358 },
359 .fifosize = 16,
360 .overrun_reg = SCLSR,
361 .overrun_mask = SCLSR_ORER,
362 .sampling_rate_mask = SCI_SR(32),
363 .error_mask = SCIF_DEFAULT_ERROR_MASK,
364 .error_clear = SCIF_ERROR_CLEAR,
365 },
366
367 /*
368 * Common SCIF definitions for ports with a Baud Rate Generator for
369 * External Clock (BRG).
370 */
371 [SCIx_SH4_SCIF_BRG_REGTYPE] = {
372 .regs = {
373 [SCSMR] = { 0x00, 16 },
374 [SCBRR] = { 0x04, 8 },
375 [SCSCR] = { 0x08, 16 },
376 [SCxTDR] = { 0x0c, 8 },
377 [SCxSR] = { 0x10, 16 },
378 [SCxRDR] = { 0x14, 8 },
379 [SCFCR] = { 0x18, 16 },
380 [SCFDR] = { 0x1c, 16 },
381 [SCSPTR] = { 0x20, 16 },
382 [SCLSR] = { 0x24, 16 },
383 [SCDL] = { 0x30, 16 },
384 [SCCKS] = { 0x34, 16 },
385 },
386 .fifosize = 16,
387 .overrun_reg = SCLSR,
388 .overrun_mask = SCLSR_ORER,
389 .sampling_rate_mask = SCI_SR(32),
390 .error_mask = SCIF_DEFAULT_ERROR_MASK,
391 .error_clear = SCIF_ERROR_CLEAR,
392 },
393
394 /*
395 * Common HSCIF definitions.
396 */
397 [SCIx_HSCIF_REGTYPE] = {
398 .regs = {
399 [SCSMR] = { 0x00, 16 },
400 [SCBRR] = { 0x04, 8 },
401 [SCSCR] = { 0x08, 16 },
402 [SCxTDR] = { 0x0c, 8 },
403 [SCxSR] = { 0x10, 16 },
404 [SCxRDR] = { 0x14, 8 },
405 [SCFCR] = { 0x18, 16 },
406 [SCFDR] = { 0x1c, 16 },
407 [SCSPTR] = { 0x20, 16 },
408 [SCLSR] = { 0x24, 16 },
409 [HSSRR] = { 0x40, 16 },
410 [SCDL] = { 0x30, 16 },
411 [SCCKS] = { 0x34, 16 },
412 [HSRTRGR] = { 0x54, 16 },
413 [HSTTRGR] = { 0x58, 16 },
414 },
415 .fifosize = 128,
416 .overrun_reg = SCLSR,
417 .overrun_mask = SCLSR_ORER,
418 .sampling_rate_mask = SCI_SR_RANGE(8, 32),
419 .error_mask = SCIF_DEFAULT_ERROR_MASK,
420 .error_clear = SCIF_ERROR_CLEAR,
421 },
422
423 /*
424 * Common SH-4(A) SCIF(B) definitions for ports without an SCSPTR
425 * register.
426 */
427 [SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE] = {
428 .regs = {
429 [SCSMR] = { 0x00, 16 },
430 [SCBRR] = { 0x04, 8 },
431 [SCSCR] = { 0x08, 16 },
432 [SCxTDR] = { 0x0c, 8 },
433 [SCxSR] = { 0x10, 16 },
434 [SCxRDR] = { 0x14, 8 },
435 [SCFCR] = { 0x18, 16 },
436 [SCFDR] = { 0x1c, 16 },
437 [SCLSR] = { 0x24, 16 },
438 },
439 .fifosize = 16,
440 .overrun_reg = SCLSR,
441 .overrun_mask = SCLSR_ORER,
442 .sampling_rate_mask = SCI_SR(32),
443 .error_mask = SCIF_DEFAULT_ERROR_MASK,
444 .error_clear = SCIF_ERROR_CLEAR,
445 },
446
447 /*
448 * Common SH-4(A) SCIF(B) definitions for ports with FIFO data
449 * count registers.
450 */
451 [SCIx_SH4_SCIF_FIFODATA_REGTYPE] = {
452 .regs = {
453 [SCSMR] = { 0x00, 16 },
454 [SCBRR] = { 0x04, 8 },
455 [SCSCR] = { 0x08, 16 },
456 [SCxTDR] = { 0x0c, 8 },
457 [SCxSR] = { 0x10, 16 },
458 [SCxRDR] = { 0x14, 8 },
459 [SCFCR] = { 0x18, 16 },
460 [SCFDR] = { 0x1c, 16 },
461 [SCTFDR] = { 0x1c, 16 }, /* aliased to SCFDR */
462 [SCRFDR] = { 0x20, 16 },
463 [SCSPTR] = { 0x24, 16 },
464 [SCLSR] = { 0x28, 16 },
465 },
466 .fifosize = 16,
467 .overrun_reg = SCLSR,
468 .overrun_mask = SCLSR_ORER,
469 .sampling_rate_mask = SCI_SR(32),
470 .error_mask = SCIF_DEFAULT_ERROR_MASK,
471 .error_clear = SCIF_ERROR_CLEAR,
472 },
473
474 /*
475 * SH7705-style SCIF(B) ports, lacking both SCSPTR and SCLSR
476 * registers.
477 */
478 [SCIx_SH7705_SCIF_REGTYPE] = {
479 .regs = {
480 [SCSMR] = { 0x00, 16 },
481 [SCBRR] = { 0x04, 8 },
482 [SCSCR] = { 0x08, 16 },
483 [SCxTDR] = { 0x20, 8 },
484 [SCxSR] = { 0x14, 16 },
485 [SCxRDR] = { 0x24, 8 },
486 [SCFCR] = { 0x18, 16 },
487 [SCFDR] = { 0x1c, 16 },
488 },
489 .fifosize = 64,
490 .overrun_reg = SCxSR,
491 .overrun_mask = SCIFA_ORER,
492 .sampling_rate_mask = SCI_SR(16),
493 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER,
494 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER,
495 },
496};
497
498#define sci_getreg(up, offset) (&to_sci_port(up)->params->regs[offset])
499
500/*
501 * The "offset" here is rather misleading, in that it refers to an enum
502 * value relative to the port mapping rather than the fixed offset
503 * itself, which needs to be manually retrieved from the platform's
504 * register map for the given port.
505 */
506static unsigned int sci_serial_in(struct uart_port *p, int offset)
507{
508 const struct plat_sci_reg *reg = sci_getreg(p, offset);
509
510 if (reg->size == 8)
511 return ioread8(p->membase + (reg->offset << p->regshift));
512 else if (reg->size == 16)
513 return ioread16(p->membase + (reg->offset << p->regshift));
514 else
515 WARN(1, "Invalid register access\n");
516
517 return 0;
518}
519
520static void sci_serial_out(struct uart_port *p, int offset, int value)
521{
522 const struct plat_sci_reg *reg = sci_getreg(p, offset);
523
524 if (reg->size == 8)
525 iowrite8(value, p->membase + (reg->offset << p->regshift));
526 else if (reg->size == 16)
527 iowrite16(value, p->membase + (reg->offset << p->regshift));
528 else
529 WARN(1, "Invalid register access\n");
530}
531
532static void sci_port_enable(struct sci_port *sci_port)
533{
534 unsigned int i;
535
536 if (!sci_port->port.dev)
537 return;
538
539 pm_runtime_get_sync(sci_port->port.dev);
540
541 for (i = 0; i < SCI_NUM_CLKS; i++) {
542 clk_prepare_enable(sci_port->clks[i]);
543 sci_port->clk_rates[i] = clk_get_rate(sci_port->clks[i]);
544 }
545 sci_port->port.uartclk = sci_port->clk_rates[SCI_FCK];
546}
547
548static void sci_port_disable(struct sci_port *sci_port)
549{
550 unsigned int i;
551
552 if (!sci_port->port.dev)
553 return;
554
555 for (i = SCI_NUM_CLKS; i-- > 0; )
556 clk_disable_unprepare(sci_port->clks[i]);
557
558 pm_runtime_put_sync(sci_port->port.dev);
559}
560
561static inline unsigned long port_rx_irq_mask(struct uart_port *port)
562{
563 /*
564 * Not all ports (such as SCIFA) will support REIE. Rather than
565 * special-casing the port type, we check the port initialization
566 * IRQ enable mask to see whether the IRQ is desired at all. If
567 * it's unset, it's logically inferred that there's no point in
568 * testing for it.
569 */
570 return SCSCR_RIE | (to_sci_port(port)->cfg->scscr & SCSCR_REIE);
571}
572
573static void sci_start_tx(struct uart_port *port)
574{
575 struct sci_port *s = to_sci_port(port);
576 unsigned short ctrl;
577
578#ifdef CONFIG_SERIAL_SH_SCI_DMA
579 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
580 u16 new, scr = serial_port_in(port, SCSCR);
581 if (s->chan_tx)
582 new = scr | SCSCR_TDRQE;
583 else
584 new = scr & ~SCSCR_TDRQE;
585 if (new != scr)
586 serial_port_out(port, SCSCR, new);
587 }
588
589 if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) &&
590 dma_submit_error(s->cookie_tx)) {
591 s->cookie_tx = 0;
592 schedule_work(&s->work_tx);
593 }
594#endif
595
596 if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
597 /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
598 ctrl = serial_port_in(port, SCSCR);
599 serial_port_out(port, SCSCR, ctrl | SCSCR_TIE);
600 }
601}
602
603static void sci_stop_tx(struct uart_port *port)
604{
605 unsigned short ctrl;
606
607 /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
608 ctrl = serial_port_in(port, SCSCR);
609
610 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
611 ctrl &= ~SCSCR_TDRQE;
612
613 ctrl &= ~SCSCR_TIE;
614
615 serial_port_out(port, SCSCR, ctrl);
616}
617
618static void sci_start_rx(struct uart_port *port)
619{
620 unsigned short ctrl;
621
622 ctrl = serial_port_in(port, SCSCR) | port_rx_irq_mask(port);
623
624 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
625 ctrl &= ~SCSCR_RDRQE;
626
627 serial_port_out(port, SCSCR, ctrl);
628}
629
630static void sci_stop_rx(struct uart_port *port)
631{
632 unsigned short ctrl;
633
634 ctrl = serial_port_in(port, SCSCR);
635
636 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
637 ctrl &= ~SCSCR_RDRQE;
638
639 ctrl &= ~port_rx_irq_mask(port);
640
641 serial_port_out(port, SCSCR, ctrl);
642}
643
644static void sci_clear_SCxSR(struct uart_port *port, unsigned int mask)
645{
646 if (port->type == PORT_SCI) {
647 /* Just store the mask */
648 serial_port_out(port, SCxSR, mask);
649 } else if (to_sci_port(port)->params->overrun_mask == SCIFA_ORER) {
650 /* SCIFA/SCIFB and SCIF on SH7705/SH7720/SH7721 */
651 /* Only clear the status bits we want to clear */
652 serial_port_out(port, SCxSR,
653 serial_port_in(port, SCxSR) & mask);
654 } else {
655 /* Store the mask, clear parity/framing errors */
656 serial_port_out(port, SCxSR, mask & ~(SCIF_FERC | SCIF_PERC));
657 }
658}
659
660#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \
661 defined(CONFIG_SERIAL_SH_SCI_EARLYCON)
662
663#ifdef CONFIG_CONSOLE_POLL
664static int sci_poll_get_char(struct uart_port *port)
665{
666 unsigned short status;
667 int c;
668
669 do {
670 status = serial_port_in(port, SCxSR);
671 if (status & SCxSR_ERRORS(port)) {
672 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port));
673 continue;
674 }
675 break;
676 } while (1);
677
678 if (!(status & SCxSR_RDxF(port)))
679 return NO_POLL_CHAR;
680
681 c = serial_port_in(port, SCxRDR);
682
683 /* Dummy read */
684 serial_port_in(port, SCxSR);
685 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
686
687 return c;
688}
689#endif
690
691static void sci_poll_put_char(struct uart_port *port, unsigned char c)
692{
693 unsigned short status;
694
695 do {
696 status = serial_port_in(port, SCxSR);
697 } while (!(status & SCxSR_TDxE(port)));
698
699 serial_port_out(port, SCxTDR, c);
700 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
701}
702#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE ||
703 CONFIG_SERIAL_SH_SCI_EARLYCON */
704
705static void sci_init_pins(struct uart_port *port, unsigned int cflag)
706{
707 struct sci_port *s = to_sci_port(port);
708
709 /*
710 * Use port-specific handler if provided.
711 */
712 if (s->cfg->ops && s->cfg->ops->init_pins) {
713 s->cfg->ops->init_pins(port, cflag);
714 return;
715 }
716
717 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
718 u16 data = serial_port_in(port, SCPDR);
719 u16 ctrl = serial_port_in(port, SCPCR);
720
721 /* Enable RXD and TXD pin functions */
722 ctrl &= ~(SCPCR_RXDC | SCPCR_TXDC);
723 if (to_sci_port(port)->has_rtscts) {
724 /* RTS# is output, active low, unless autorts */
725 if (!(port->mctrl & TIOCM_RTS)) {
726 ctrl |= SCPCR_RTSC;
727 data |= SCPDR_RTSD;
728 } else if (!s->autorts) {
729 ctrl |= SCPCR_RTSC;
730 data &= ~SCPDR_RTSD;
731 } else {
732 /* Enable RTS# pin function */
733 ctrl &= ~SCPCR_RTSC;
734 }
735 /* Enable CTS# pin function */
736 ctrl &= ~SCPCR_CTSC;
737 }
738 serial_port_out(port, SCPDR, data);
739 serial_port_out(port, SCPCR, ctrl);
740 } else if (sci_getreg(port, SCSPTR)->size) {
741 u16 status = serial_port_in(port, SCSPTR);
742
743 /* RTS# is always output; and active low, unless autorts */
744 status |= SCSPTR_RTSIO;
745 if (!(port->mctrl & TIOCM_RTS))
746 status |= SCSPTR_RTSDT;
747 else if (!s->autorts)
748 status &= ~SCSPTR_RTSDT;
749 /* CTS# and SCK are inputs */
750 status &= ~(SCSPTR_CTSIO | SCSPTR_SCKIO);
751 serial_port_out(port, SCSPTR, status);
752 }
753}
754
755static int sci_txfill(struct uart_port *port)
756{
757 struct sci_port *s = to_sci_port(port);
758 unsigned int fifo_mask = (s->params->fifosize << 1) - 1;
759 const struct plat_sci_reg *reg;
760
761 reg = sci_getreg(port, SCTFDR);
762 if (reg->size)
763 return serial_port_in(port, SCTFDR) & fifo_mask;
764
765 reg = sci_getreg(port, SCFDR);
766 if (reg->size)
767 return serial_port_in(port, SCFDR) >> 8;
768
769 return !(serial_port_in(port, SCxSR) & SCI_TDRE);
770}
771
772static int sci_txroom(struct uart_port *port)
773{
774 return port->fifosize - sci_txfill(port);
775}
776
777static int sci_rxfill(struct uart_port *port)
778{
779 struct sci_port *s = to_sci_port(port);
780 unsigned int fifo_mask = (s->params->fifosize << 1) - 1;
781 const struct plat_sci_reg *reg;
782
783 reg = sci_getreg(port, SCRFDR);
784 if (reg->size)
785 return serial_port_in(port, SCRFDR) & fifo_mask;
786
787 reg = sci_getreg(port, SCFDR);
788 if (reg->size)
789 return serial_port_in(port, SCFDR) & fifo_mask;
790
791 return (serial_port_in(port, SCxSR) & SCxSR_RDxF(port)) != 0;
792}
793
794/* ********************************************************************** *
795 * the interrupt related routines *
796 * ********************************************************************** */
797
798static void sci_transmit_chars(struct uart_port *port)
799{
800 struct circ_buf *xmit = &port->state->xmit;
801 unsigned int stopped = uart_tx_stopped(port);
802 unsigned short status;
803 unsigned short ctrl;
804 int count;
805
806 status = serial_port_in(port, SCxSR);
807 if (!(status & SCxSR_TDxE(port))) {
808 ctrl = serial_port_in(port, SCSCR);
809 if (uart_circ_empty(xmit))
810 ctrl &= ~SCSCR_TIE;
811 else
812 ctrl |= SCSCR_TIE;
813 serial_port_out(port, SCSCR, ctrl);
814 return;
815 }
816
817 count = sci_txroom(port);
818
819 do {
820 unsigned char c;
821
822 if (port->x_char) {
823 c = port->x_char;
824 port->x_char = 0;
825 } else if (!uart_circ_empty(xmit) && !stopped) {
826 c = xmit->buf[xmit->tail];
827 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
828 } else {
829 break;
830 }
831
832 serial_port_out(port, SCxTDR, c);
833
834 port->icount.tx++;
835 } while (--count > 0);
836
837 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port));
838
839 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
840 uart_write_wakeup(port);
841 if (uart_circ_empty(xmit))
842 sci_stop_tx(port);
843
844}
845
846/* On SH3, SCIF may read end-of-break as a space->mark char */
847#define STEPFN(c) ({int __c = (c); (((__c-1)|(__c)) == -1); })
848
849static void sci_receive_chars(struct uart_port *port)
850{
851 struct tty_port *tport = &port->state->port;
852 int i, count, copied = 0;
853 unsigned short status;
854 unsigned char flag;
855
856 status = serial_port_in(port, SCxSR);
857 if (!(status & SCxSR_RDxF(port)))
858 return;
859
860 while (1) {
861 /* Don't copy more bytes than there is room for in the buffer */
862 count = tty_buffer_request_room(tport, sci_rxfill(port));
863
864 /* If for any reason we can't copy more data, we're done! */
865 if (count == 0)
866 break;
867
868 if (port->type == PORT_SCI) {
869 char c = serial_port_in(port, SCxRDR);
870 if (uart_handle_sysrq_char(port, c))
871 count = 0;
872 else
873 tty_insert_flip_char(tport, c, TTY_NORMAL);
874 } else {
875 for (i = 0; i < count; i++) {
876 char c = serial_port_in(port, SCxRDR);
877
878 status = serial_port_in(port, SCxSR);
879 if (uart_handle_sysrq_char(port, c)) {
880 count--; i--;
881 continue;
882 }
883
884 /* Store data and status */
885 if (status & SCxSR_FER(port)) {
886 flag = TTY_FRAME;
887 port->icount.frame++;
888 dev_notice(port->dev, "frame error\n");
889 } else if (status & SCxSR_PER(port)) {
890 flag = TTY_PARITY;
891 port->icount.parity++;
892 dev_notice(port->dev, "parity error\n");
893 } else
894 flag = TTY_NORMAL;
895
896 tty_insert_flip_char(tport, c, flag);
897 }
898 }
899
900 serial_port_in(port, SCxSR); /* dummy read */
901 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
902
903 copied += count;
904 port->icount.rx += count;
905 }
906
907 if (copied) {
908 /* Tell the rest of the system the news. New characters! */
909 tty_flip_buffer_push(tport);
910 } else {
911 /* TTY buffers full; read from RX reg to prevent lockup */
912 serial_port_in(port, SCxRDR);
913 serial_port_in(port, SCxSR); /* dummy read */
914 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
915 }
916}
917
918static int sci_handle_errors(struct uart_port *port)
919{
920 int copied = 0;
921 unsigned short status = serial_port_in(port, SCxSR);
922 struct tty_port *tport = &port->state->port;
923 struct sci_port *s = to_sci_port(port);
924
925 /* Handle overruns */
926 if (status & s->params->overrun_mask) {
927 port->icount.overrun++;
928
929 /* overrun error */
930 if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
931 copied++;
932
933 dev_notice(port->dev, "overrun error\n");
934 }
935
936 if (status & SCxSR_FER(port)) {
937 /* frame error */
938 port->icount.frame++;
939
940 if (tty_insert_flip_char(tport, 0, TTY_FRAME))
941 copied++;
942
943 dev_notice(port->dev, "frame error\n");
944 }
945
946 if (status & SCxSR_PER(port)) {
947 /* parity error */
948 port->icount.parity++;
949
950 if (tty_insert_flip_char(tport, 0, TTY_PARITY))
951 copied++;
952
953 dev_notice(port->dev, "parity error\n");
954 }
955
956 if (copied)
957 tty_flip_buffer_push(tport);
958
959 return copied;
960}
961
962static int sci_handle_fifo_overrun(struct uart_port *port)
963{
964 struct tty_port *tport = &port->state->port;
965 struct sci_port *s = to_sci_port(port);
966 const struct plat_sci_reg *reg;
967 int copied = 0;
968 u16 status;
969
970 reg = sci_getreg(port, s->params->overrun_reg);
971 if (!reg->size)
972 return 0;
973
974 status = serial_port_in(port, s->params->overrun_reg);
975 if (status & s->params->overrun_mask) {
976 status &= ~s->params->overrun_mask;
977 serial_port_out(port, s->params->overrun_reg, status);
978
979 port->icount.overrun++;
980
981 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
982 tty_flip_buffer_push(tport);
983
984 dev_dbg(port->dev, "overrun error\n");
985 copied++;
986 }
987
988 return copied;
989}
990
991static int sci_handle_breaks(struct uart_port *port)
992{
993 int copied = 0;
994 unsigned short status = serial_port_in(port, SCxSR);
995 struct tty_port *tport = &port->state->port;
996
997 if (uart_handle_break(port))
998 return 0;
999
1000 if (status & SCxSR_BRK(port)) {
1001 port->icount.brk++;
1002
1003 /* Notify of BREAK */
1004 if (tty_insert_flip_char(tport, 0, TTY_BREAK))
1005 copied++;
1006
1007 dev_dbg(port->dev, "BREAK detected\n");
1008 }
1009
1010 if (copied)
1011 tty_flip_buffer_push(tport);
1012
1013 copied += sci_handle_fifo_overrun(port);
1014
1015 return copied;
1016}
1017
1018static int scif_set_rtrg(struct uart_port *port, int rx_trig)
1019{
1020 unsigned int bits;
1021
1022 if (rx_trig < 1)
1023 rx_trig = 1;
1024 if (rx_trig >= port->fifosize)
1025 rx_trig = port->fifosize;
1026
1027 /* HSCIF can be set to an arbitrary level. */
1028 if (sci_getreg(port, HSRTRGR)->size) {
1029 serial_port_out(port, HSRTRGR, rx_trig);
1030 return rx_trig;
1031 }
1032
1033 switch (port->type) {
1034 case PORT_SCIF:
1035 if (rx_trig < 4) {
1036 bits = 0;
1037 rx_trig = 1;
1038 } else if (rx_trig < 8) {
1039 bits = SCFCR_RTRG0;
1040 rx_trig = 4;
1041 } else if (rx_trig < 14) {
1042 bits = SCFCR_RTRG1;
1043 rx_trig = 8;
1044 } else {
1045 bits = SCFCR_RTRG0 | SCFCR_RTRG1;
1046 rx_trig = 14;
1047 }
1048 break;
1049 case PORT_SCIFA:
1050 case PORT_SCIFB:
1051 if (rx_trig < 16) {
1052 bits = 0;
1053 rx_trig = 1;
1054 } else if (rx_trig < 32) {
1055 bits = SCFCR_RTRG0;
1056 rx_trig = 16;
1057 } else if (rx_trig < 48) {
1058 bits = SCFCR_RTRG1;
1059 rx_trig = 32;
1060 } else {
1061 bits = SCFCR_RTRG0 | SCFCR_RTRG1;
1062 rx_trig = 48;
1063 }
1064 break;
1065 default:
1066 WARN(1, "unknown FIFO configuration");
1067 return 1;
1068 }
1069
1070 serial_port_out(port, SCFCR,
1071 (serial_port_in(port, SCFCR) &
1072 ~(SCFCR_RTRG1 | SCFCR_RTRG0)) | bits);
1073
1074 return rx_trig;
1075}
1076
1077static int scif_rtrg_enabled(struct uart_port *port)
1078{
1079 if (sci_getreg(port, HSRTRGR)->size)
1080 return serial_port_in(port, HSRTRGR) != 0;
1081 else
1082 return (serial_port_in(port, SCFCR) &
1083 (SCFCR_RTRG0 | SCFCR_RTRG1)) != 0;
1084}
1085
1086static void rx_fifo_timer_fn(struct timer_list *t)
1087{
1088 struct sci_port *s = from_timer(s, t, rx_fifo_timer);
1089 struct uart_port *port = &s->port;
1090
1091 dev_dbg(port->dev, "Rx timed out\n");
1092 scif_set_rtrg(port, 1);
1093}
1094
1095static ssize_t rx_fifo_trigger_show(struct device *dev,
1096 struct device_attribute *attr, char *buf)
1097{
1098 struct uart_port *port = dev_get_drvdata(dev);
1099 struct sci_port *sci = to_sci_port(port);
1100
1101 return sprintf(buf, "%d\n", sci->rx_trigger);
1102}
1103
1104static ssize_t rx_fifo_trigger_store(struct device *dev,
1105 struct device_attribute *attr,
1106 const char *buf, size_t count)
1107{
1108 struct uart_port *port = dev_get_drvdata(dev);
1109 struct sci_port *sci = to_sci_port(port);
1110 int ret;
1111 long r;
1112
1113 ret = kstrtol(buf, 0, &r);
1114 if (ret)
1115 return ret;
1116
1117 sci->rx_trigger = scif_set_rtrg(port, r);
1118 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1119 scif_set_rtrg(port, 1);
1120
1121 return count;
1122}
1123
1124static DEVICE_ATTR_RW(rx_fifo_trigger);
1125
1126static ssize_t rx_fifo_timeout_show(struct device *dev,
1127 struct device_attribute *attr,
1128 char *buf)
1129{
1130 struct uart_port *port = dev_get_drvdata(dev);
1131 struct sci_port *sci = to_sci_port(port);
1132 int v;
1133
1134 if (port->type == PORT_HSCIF)
1135 v = sci->hscif_tot >> HSSCR_TOT_SHIFT;
1136 else
1137 v = sci->rx_fifo_timeout;
1138
1139 return sprintf(buf, "%d\n", v);
1140}
1141
1142static ssize_t rx_fifo_timeout_store(struct device *dev,
1143 struct device_attribute *attr,
1144 const char *buf,
1145 size_t count)
1146{
1147 struct uart_port *port = dev_get_drvdata(dev);
1148 struct sci_port *sci = to_sci_port(port);
1149 int ret;
1150 long r;
1151
1152 ret = kstrtol(buf, 0, &r);
1153 if (ret)
1154 return ret;
1155
1156 if (port->type == PORT_HSCIF) {
1157 if (r < 0 || r > 3)
1158 return -EINVAL;
1159 sci->hscif_tot = r << HSSCR_TOT_SHIFT;
1160 } else {
1161 sci->rx_fifo_timeout = r;
1162 scif_set_rtrg(port, 1);
1163 if (r > 0)
1164 timer_setup(&sci->rx_fifo_timer, rx_fifo_timer_fn, 0);
1165 }
1166
1167 return count;
1168}
1169
1170static DEVICE_ATTR_RW(rx_fifo_timeout);
1171
1172
1173#ifdef CONFIG_SERIAL_SH_SCI_DMA
1174static void sci_dma_tx_complete(void *arg)
1175{
1176 struct sci_port *s = arg;
1177 struct uart_port *port = &s->port;
1178 struct circ_buf *xmit = &port->state->xmit;
1179 unsigned long flags;
1180
1181 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1182
1183 spin_lock_irqsave(&port->lock, flags);
1184
1185 xmit->tail += s->tx_dma_len;
1186 xmit->tail &= UART_XMIT_SIZE - 1;
1187
1188 port->icount.tx += s->tx_dma_len;
1189
1190 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1191 uart_write_wakeup(port);
1192
1193 if (!uart_circ_empty(xmit)) {
1194 s->cookie_tx = 0;
1195 schedule_work(&s->work_tx);
1196 } else {
1197 s->cookie_tx = -EINVAL;
1198 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1199 u16 ctrl = serial_port_in(port, SCSCR);
1200 serial_port_out(port, SCSCR, ctrl & ~SCSCR_TIE);
1201 }
1202 }
1203
1204 spin_unlock_irqrestore(&port->lock, flags);
1205}
1206
1207/* Locking: called with port lock held */
1208static int sci_dma_rx_push(struct sci_port *s, void *buf, size_t count)
1209{
1210 struct uart_port *port = &s->port;
1211 struct tty_port *tport = &port->state->port;
1212 int copied;
1213
1214 copied = tty_insert_flip_string(tport, buf, count);
1215 if (copied < count)
1216 port->icount.buf_overrun++;
1217
1218 port->icount.rx += copied;
1219
1220 return copied;
1221}
1222
1223static int sci_dma_rx_find_active(struct sci_port *s)
1224{
1225 unsigned int i;
1226
1227 for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++)
1228 if (s->active_rx == s->cookie_rx[i])
1229 return i;
1230
1231 return -1;
1232}
1233
1234static void sci_dma_rx_chan_invalidate(struct sci_port *s)
1235{
1236 unsigned int i;
1237
1238 s->chan_rx = NULL;
1239 for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++)
1240 s->cookie_rx[i] = -EINVAL;
1241 s->active_rx = 0;
1242}
1243
1244static void sci_dma_rx_release(struct sci_port *s)
1245{
1246 struct dma_chan *chan = s->chan_rx_saved;
1247
1248 s->chan_rx_saved = NULL;
1249 sci_dma_rx_chan_invalidate(s);
1250 dmaengine_terminate_sync(chan);
1251 dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0],
1252 sg_dma_address(&s->sg_rx[0]));
1253 dma_release_channel(chan);
1254}
1255
1256static void start_hrtimer_us(struct hrtimer *hrt, unsigned long usec)
1257{
1258 long sec = usec / 1000000;
1259 long nsec = (usec % 1000000) * 1000;
1260 ktime_t t = ktime_set(sec, nsec);
1261
1262 hrtimer_start(hrt, t, HRTIMER_MODE_REL);
1263}
1264
1265static void sci_dma_rx_reenable_irq(struct sci_port *s)
1266{
1267 struct uart_port *port = &s->port;
1268 u16 scr;
1269
1270 /* Direct new serial port interrupts back to CPU */
1271 scr = serial_port_in(port, SCSCR);
1272 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1273 scr &= ~SCSCR_RDRQE;
1274 enable_irq(s->irqs[SCIx_RXI_IRQ]);
1275 }
1276 serial_port_out(port, SCSCR, scr | SCSCR_RIE);
1277}
1278
1279static void sci_dma_rx_complete(void *arg)
1280{
1281 struct sci_port *s = arg;
1282 struct dma_chan *chan = s->chan_rx;
1283 struct uart_port *port = &s->port;
1284 struct dma_async_tx_descriptor *desc;
1285 unsigned long flags;
1286 int active, count = 0;
1287
1288 dev_dbg(port->dev, "%s(%d) active cookie %d\n", __func__, port->line,
1289 s->active_rx);
1290
1291 spin_lock_irqsave(&port->lock, flags);
1292
1293 active = sci_dma_rx_find_active(s);
1294 if (active >= 0)
1295 count = sci_dma_rx_push(s, s->rx_buf[active], s->buf_len_rx);
1296
1297 start_hrtimer_us(&s->rx_timer, s->rx_timeout);
1298
1299 if (count)
1300 tty_flip_buffer_push(&port->state->port);
1301
1302 desc = dmaengine_prep_slave_sg(s->chan_rx, &s->sg_rx[active], 1,
1303 DMA_DEV_TO_MEM,
1304 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1305 if (!desc)
1306 goto fail;
1307
1308 desc->callback = sci_dma_rx_complete;
1309 desc->callback_param = s;
1310 s->cookie_rx[active] = dmaengine_submit(desc);
1311 if (dma_submit_error(s->cookie_rx[active]))
1312 goto fail;
1313
1314 s->active_rx = s->cookie_rx[!active];
1315
1316 dma_async_issue_pending(chan);
1317
1318 spin_unlock_irqrestore(&port->lock, flags);
1319 dev_dbg(port->dev, "%s: cookie %d #%d, new active cookie %d\n",
1320 __func__, s->cookie_rx[active], active, s->active_rx);
1321 return;
1322
1323fail:
1324 spin_unlock_irqrestore(&port->lock, flags);
1325 dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
1326 /* Switch to PIO */
1327 spin_lock_irqsave(&port->lock, flags);
1328 dmaengine_terminate_async(chan);
1329 sci_dma_rx_chan_invalidate(s);
1330 sci_dma_rx_reenable_irq(s);
1331 spin_unlock_irqrestore(&port->lock, flags);
1332}
1333
1334static void sci_dma_tx_release(struct sci_port *s)
1335{
1336 struct dma_chan *chan = s->chan_tx_saved;
1337
1338 cancel_work_sync(&s->work_tx);
1339 s->chan_tx_saved = s->chan_tx = NULL;
1340 s->cookie_tx = -EINVAL;
1341 dmaengine_terminate_sync(chan);
1342 dma_unmap_single(chan->device->dev, s->tx_dma_addr, UART_XMIT_SIZE,
1343 DMA_TO_DEVICE);
1344 dma_release_channel(chan);
1345}
1346
1347static int sci_dma_rx_submit(struct sci_port *s, bool port_lock_held)
1348{
1349 struct dma_chan *chan = s->chan_rx;
1350 struct uart_port *port = &s->port;
1351 unsigned long flags;
1352 int i;
1353
1354 for (i = 0; i < 2; i++) {
1355 struct scatterlist *sg = &s->sg_rx[i];
1356 struct dma_async_tx_descriptor *desc;
1357
1358 desc = dmaengine_prep_slave_sg(chan,
1359 sg, 1, DMA_DEV_TO_MEM,
1360 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1361 if (!desc)
1362 goto fail;
1363
1364 desc->callback = sci_dma_rx_complete;
1365 desc->callback_param = s;
1366 s->cookie_rx[i] = dmaengine_submit(desc);
1367 if (dma_submit_error(s->cookie_rx[i]))
1368 goto fail;
1369
1370 }
1371
1372 s->active_rx = s->cookie_rx[0];
1373
1374 dma_async_issue_pending(chan);
1375 return 0;
1376
1377fail:
1378 /* Switch to PIO */
1379 if (!port_lock_held)
1380 spin_lock_irqsave(&port->lock, flags);
1381 if (i)
1382 dmaengine_terminate_async(chan);
1383 sci_dma_rx_chan_invalidate(s);
1384 sci_start_rx(port);
1385 if (!port_lock_held)
1386 spin_unlock_irqrestore(&port->lock, flags);
1387 return -EAGAIN;
1388}
1389
1390static void sci_dma_tx_work_fn(struct work_struct *work)
1391{
1392 struct sci_port *s = container_of(work, struct sci_port, work_tx);
1393 struct dma_async_tx_descriptor *desc;
1394 struct dma_chan *chan = s->chan_tx;
1395 struct uart_port *port = &s->port;
1396 struct circ_buf *xmit = &port->state->xmit;
1397 unsigned long flags;
1398 dma_addr_t buf;
1399 int head, tail;
1400
1401 /*
1402 * DMA is idle now.
1403 * Port xmit buffer is already mapped, and it is one page... Just adjust
1404 * offsets and lengths. Since it is a circular buffer, we have to
1405 * transmit till the end, and then the rest. Take the port lock to get a
1406 * consistent xmit buffer state.
1407 */
1408 spin_lock_irq(&port->lock);
1409 head = xmit->head;
1410 tail = xmit->tail;
1411 buf = s->tx_dma_addr + (tail & (UART_XMIT_SIZE - 1));
1412 s->tx_dma_len = min_t(unsigned int,
1413 CIRC_CNT(head, tail, UART_XMIT_SIZE),
1414 CIRC_CNT_TO_END(head, tail, UART_XMIT_SIZE));
1415 if (!s->tx_dma_len) {
1416 /* Transmit buffer has been flushed */
1417 spin_unlock_irq(&port->lock);
1418 return;
1419 }
1420
1421 desc = dmaengine_prep_slave_single(chan, buf, s->tx_dma_len,
1422 DMA_MEM_TO_DEV,
1423 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1424 if (!desc) {
1425 spin_unlock_irq(&port->lock);
1426 dev_warn(port->dev, "Failed preparing Tx DMA descriptor\n");
1427 goto switch_to_pio;
1428 }
1429
1430 dma_sync_single_for_device(chan->device->dev, buf, s->tx_dma_len,
1431 DMA_TO_DEVICE);
1432
1433 desc->callback = sci_dma_tx_complete;
1434 desc->callback_param = s;
1435 s->cookie_tx = dmaengine_submit(desc);
1436 if (dma_submit_error(s->cookie_tx)) {
1437 spin_unlock_irq(&port->lock);
1438 dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n");
1439 goto switch_to_pio;
1440 }
1441
1442 spin_unlock_irq(&port->lock);
1443 dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n",
1444 __func__, xmit->buf, tail, head, s->cookie_tx);
1445
1446 dma_async_issue_pending(chan);
1447 return;
1448
1449switch_to_pio:
1450 spin_lock_irqsave(&port->lock, flags);
1451 s->chan_tx = NULL;
1452 sci_start_tx(port);
1453 spin_unlock_irqrestore(&port->lock, flags);
1454 return;
1455}
1456
1457static enum hrtimer_restart sci_dma_rx_timer_fn(struct hrtimer *t)
1458{
1459 struct sci_port *s = container_of(t, struct sci_port, rx_timer);
1460 struct dma_chan *chan = s->chan_rx;
1461 struct uart_port *port = &s->port;
1462 struct dma_tx_state state;
1463 enum dma_status status;
1464 unsigned long flags;
1465 unsigned int read;
1466 int active, count;
1467
1468 dev_dbg(port->dev, "DMA Rx timed out\n");
1469
1470 spin_lock_irqsave(&port->lock, flags);
1471
1472 active = sci_dma_rx_find_active(s);
1473 if (active < 0) {
1474 spin_unlock_irqrestore(&port->lock, flags);
1475 return HRTIMER_NORESTART;
1476 }
1477
1478 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state);
1479 if (status == DMA_COMPLETE) {
1480 spin_unlock_irqrestore(&port->lock, flags);
1481 dev_dbg(port->dev, "Cookie %d #%d has already completed\n",
1482 s->active_rx, active);
1483
1484 /* Let packet complete handler take care of the packet */
1485 return HRTIMER_NORESTART;
1486 }
1487
1488 dmaengine_pause(chan);
1489
1490 /*
1491 * sometimes DMA transfer doesn't stop even if it is stopped and
1492 * data keeps on coming until transaction is complete so check
1493 * for DMA_COMPLETE again
1494 * Let packet complete handler take care of the packet
1495 */
1496 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state);
1497 if (status == DMA_COMPLETE) {
1498 spin_unlock_irqrestore(&port->lock, flags);
1499 dev_dbg(port->dev, "Transaction complete after DMA engine was stopped");
1500 return HRTIMER_NORESTART;
1501 }
1502
1503 /* Handle incomplete DMA receive */
1504 dmaengine_terminate_async(s->chan_rx);
1505 read = sg_dma_len(&s->sg_rx[active]) - state.residue;
1506
1507 if (read) {
1508 count = sci_dma_rx_push(s, s->rx_buf[active], read);
1509 if (count)
1510 tty_flip_buffer_push(&port->state->port);
1511 }
1512
1513 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1514 sci_dma_rx_submit(s, true);
1515
1516 sci_dma_rx_reenable_irq(s);
1517
1518 spin_unlock_irqrestore(&port->lock, flags);
1519
1520 return HRTIMER_NORESTART;
1521}
1522
1523static struct dma_chan *sci_request_dma_chan(struct uart_port *port,
1524 enum dma_transfer_direction dir)
1525{
1526 struct dma_chan *chan;
1527 struct dma_slave_config cfg;
1528 int ret;
1529
1530 chan = dma_request_slave_channel(port->dev,
1531 dir == DMA_MEM_TO_DEV ? "tx" : "rx");
1532 if (!chan) {
1533 dev_dbg(port->dev, "dma_request_slave_channel failed\n");
1534 return NULL;
1535 }
1536
1537 memset(&cfg, 0, sizeof(cfg));
1538 cfg.direction = dir;
1539 if (dir == DMA_MEM_TO_DEV) {
1540 cfg.dst_addr = port->mapbase +
1541 (sci_getreg(port, SCxTDR)->offset << port->regshift);
1542 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1543 } else {
1544 cfg.src_addr = port->mapbase +
1545 (sci_getreg(port, SCxRDR)->offset << port->regshift);
1546 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1547 }
1548
1549 ret = dmaengine_slave_config(chan, &cfg);
1550 if (ret) {
1551 dev_warn(port->dev, "dmaengine_slave_config failed %d\n", ret);
1552 dma_release_channel(chan);
1553 return NULL;
1554 }
1555
1556 return chan;
1557}
1558
1559static void sci_request_dma(struct uart_port *port)
1560{
1561 struct sci_port *s = to_sci_port(port);
1562 struct dma_chan *chan;
1563
1564 dev_dbg(port->dev, "%s: port %d\n", __func__, port->line);
1565
1566 /*
1567 * DMA on console may interfere with Kernel log messages which use
1568 * plain putchar(). So, simply don't use it with a console.
1569 */
1570 if (uart_console(port))
1571 return;
1572
1573 if (!port->dev->of_node)
1574 return;
1575
1576 s->cookie_tx = -EINVAL;
1577
1578 /*
1579 * Don't request a dma channel if no channel was specified
1580 * in the device tree.
1581 */
1582 if (!of_find_property(port->dev->of_node, "dmas", NULL))
1583 return;
1584
1585 chan = sci_request_dma_chan(port, DMA_MEM_TO_DEV);
1586 dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan);
1587 if (chan) {
1588 /* UART circular tx buffer is an aligned page. */
1589 s->tx_dma_addr = dma_map_single(chan->device->dev,
1590 port->state->xmit.buf,
1591 UART_XMIT_SIZE,
1592 DMA_TO_DEVICE);
1593 if (dma_mapping_error(chan->device->dev, s->tx_dma_addr)) {
1594 dev_warn(port->dev, "Failed mapping Tx DMA descriptor\n");
1595 dma_release_channel(chan);
1596 } else {
1597 dev_dbg(port->dev, "%s: mapped %lu@%p to %pad\n",
1598 __func__, UART_XMIT_SIZE,
1599 port->state->xmit.buf, &s->tx_dma_addr);
1600
1601 INIT_WORK(&s->work_tx, sci_dma_tx_work_fn);
1602 s->chan_tx_saved = s->chan_tx = chan;
1603 }
1604 }
1605
1606 chan = sci_request_dma_chan(port, DMA_DEV_TO_MEM);
1607 dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan);
1608 if (chan) {
1609 unsigned int i;
1610 dma_addr_t dma;
1611 void *buf;
1612
1613 s->buf_len_rx = 2 * max_t(size_t, 16, port->fifosize);
1614 buf = dma_alloc_coherent(chan->device->dev, s->buf_len_rx * 2,
1615 &dma, GFP_KERNEL);
1616 if (!buf) {
1617 dev_warn(port->dev,
1618 "Failed to allocate Rx dma buffer, using PIO\n");
1619 dma_release_channel(chan);
1620 return;
1621 }
1622
1623 for (i = 0; i < 2; i++) {
1624 struct scatterlist *sg = &s->sg_rx[i];
1625
1626 sg_init_table(sg, 1);
1627 s->rx_buf[i] = buf;
1628 sg_dma_address(sg) = dma;
1629 sg_dma_len(sg) = s->buf_len_rx;
1630
1631 buf += s->buf_len_rx;
1632 dma += s->buf_len_rx;
1633 }
1634
1635 hrtimer_init(&s->rx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
1636 s->rx_timer.function = sci_dma_rx_timer_fn;
1637
1638 s->chan_rx_saved = s->chan_rx = chan;
1639
1640 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1641 sci_dma_rx_submit(s, false);
1642 }
1643}
1644
1645static void sci_free_dma(struct uart_port *port)
1646{
1647 struct sci_port *s = to_sci_port(port);
1648
1649 if (s->chan_tx_saved)
1650 sci_dma_tx_release(s);
1651 if (s->chan_rx_saved)
1652 sci_dma_rx_release(s);
1653}
1654
1655static void sci_flush_buffer(struct uart_port *port)
1656{
1657 struct sci_port *s = to_sci_port(port);
1658
1659 /*
1660 * In uart_flush_buffer(), the xmit circular buffer has just been
1661 * cleared, so we have to reset tx_dma_len accordingly, and stop any
1662 * pending transfers
1663 */
1664 s->tx_dma_len = 0;
1665 if (s->chan_tx) {
1666 dmaengine_terminate_async(s->chan_tx);
1667 s->cookie_tx = -EINVAL;
1668 }
1669}
1670#else /* !CONFIG_SERIAL_SH_SCI_DMA */
1671static inline void sci_request_dma(struct uart_port *port)
1672{
1673}
1674
1675static inline void sci_free_dma(struct uart_port *port)
1676{
1677}
1678
1679#define sci_flush_buffer NULL
1680#endif /* !CONFIG_SERIAL_SH_SCI_DMA */
1681
1682static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
1683{
1684 struct uart_port *port = ptr;
1685 struct sci_port *s = to_sci_port(port);
1686
1687#ifdef CONFIG_SERIAL_SH_SCI_DMA
1688 if (s->chan_rx) {
1689 u16 scr = serial_port_in(port, SCSCR);
1690 u16 ssr = serial_port_in(port, SCxSR);
1691
1692 /* Disable future Rx interrupts */
1693 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1694 disable_irq_nosync(irq);
1695 scr |= SCSCR_RDRQE;
1696 } else {
1697 if (sci_dma_rx_submit(s, false) < 0)
1698 goto handle_pio;
1699
1700 scr &= ~SCSCR_RIE;
1701 }
1702 serial_port_out(port, SCSCR, scr);
1703 /* Clear current interrupt */
1704 serial_port_out(port, SCxSR,
1705 ssr & ~(SCIF_DR | SCxSR_RDxF(port)));
1706 dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u us\n",
1707 jiffies, s->rx_timeout);
1708 start_hrtimer_us(&s->rx_timer, s->rx_timeout);
1709
1710 return IRQ_HANDLED;
1711 }
1712
1713handle_pio:
1714#endif
1715
1716 if (s->rx_trigger > 1 && s->rx_fifo_timeout > 0) {
1717 if (!scif_rtrg_enabled(port))
1718 scif_set_rtrg(port, s->rx_trigger);
1719
1720 mod_timer(&s->rx_fifo_timer, jiffies + DIV_ROUND_UP(
1721 s->rx_frame * HZ * s->rx_fifo_timeout, 1000000));
1722 }
1723
1724 /* I think sci_receive_chars has to be called irrespective
1725 * of whether the I_IXOFF is set, otherwise, how is the interrupt
1726 * to be disabled?
1727 */
1728 sci_receive_chars(port);
1729
1730 return IRQ_HANDLED;
1731}
1732
1733static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
1734{
1735 struct uart_port *port = ptr;
1736 unsigned long flags;
1737
1738 spin_lock_irqsave(&port->lock, flags);
1739 sci_transmit_chars(port);
1740 spin_unlock_irqrestore(&port->lock, flags);
1741
1742 return IRQ_HANDLED;
1743}
1744
1745static irqreturn_t sci_br_interrupt(int irq, void *ptr)
1746{
1747 struct uart_port *port = ptr;
1748
1749 /* Handle BREAKs */
1750 sci_handle_breaks(port);
1751 sci_clear_SCxSR(port, SCxSR_BREAK_CLEAR(port));
1752
1753 return IRQ_HANDLED;
1754}
1755
1756static irqreturn_t sci_er_interrupt(int irq, void *ptr)
1757{
1758 struct uart_port *port = ptr;
1759 struct sci_port *s = to_sci_port(port);
1760
1761 if (s->irqs[SCIx_ERI_IRQ] == s->irqs[SCIx_BRI_IRQ]) {
1762 /* Break and Error interrupts are muxed */
1763 unsigned short ssr_status = serial_port_in(port, SCxSR);
1764
1765 /* Break Interrupt */
1766 if (ssr_status & SCxSR_BRK(port))
1767 sci_br_interrupt(irq, ptr);
1768
1769 /* Break only? */
1770 if (!(ssr_status & SCxSR_ERRORS(port)))
1771 return IRQ_HANDLED;
1772 }
1773
1774 /* Handle errors */
1775 if (port->type == PORT_SCI) {
1776 if (sci_handle_errors(port)) {
1777 /* discard character in rx buffer */
1778 serial_port_in(port, SCxSR);
1779 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
1780 }
1781 } else {
1782 sci_handle_fifo_overrun(port);
1783 if (!s->chan_rx)
1784 sci_receive_chars(port);
1785 }
1786
1787 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port));
1788
1789 /* Kick the transmission */
1790 if (!s->chan_tx)
1791 sci_tx_interrupt(irq, ptr);
1792
1793 return IRQ_HANDLED;
1794}
1795
1796static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
1797{
1798 unsigned short ssr_status, scr_status, err_enabled, orer_status = 0;
1799 struct uart_port *port = ptr;
1800 struct sci_port *s = to_sci_port(port);
1801 irqreturn_t ret = IRQ_NONE;
1802
1803 ssr_status = serial_port_in(port, SCxSR);
1804 scr_status = serial_port_in(port, SCSCR);
1805 if (s->params->overrun_reg == SCxSR)
1806 orer_status = ssr_status;
1807 else if (sci_getreg(port, s->params->overrun_reg)->size)
1808 orer_status = serial_port_in(port, s->params->overrun_reg);
1809
1810 err_enabled = scr_status & port_rx_irq_mask(port);
1811
1812 /* Tx Interrupt */
1813 if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) &&
1814 !s->chan_tx)
1815 ret = sci_tx_interrupt(irq, ptr);
1816
1817 /*
1818 * Rx Interrupt: if we're using DMA, the DMA controller clears RDF /
1819 * DR flags
1820 */
1821 if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) &&
1822 (scr_status & SCSCR_RIE))
1823 ret = sci_rx_interrupt(irq, ptr);
1824
1825 /* Error Interrupt */
1826 if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled)
1827 ret = sci_er_interrupt(irq, ptr);
1828
1829 /* Break Interrupt */
1830 if ((ssr_status & SCxSR_BRK(port)) && err_enabled)
1831 ret = sci_br_interrupt(irq, ptr);
1832
1833 /* Overrun Interrupt */
1834 if (orer_status & s->params->overrun_mask) {
1835 sci_handle_fifo_overrun(port);
1836 ret = IRQ_HANDLED;
1837 }
1838
1839 return ret;
1840}
1841
1842static const struct sci_irq_desc {
1843 const char *desc;
1844 irq_handler_t handler;
1845} sci_irq_desc[] = {
1846 /*
1847 * Split out handlers, the default case.
1848 */
1849 [SCIx_ERI_IRQ] = {
1850 .desc = "rx err",
1851 .handler = sci_er_interrupt,
1852 },
1853
1854 [SCIx_RXI_IRQ] = {
1855 .desc = "rx full",
1856 .handler = sci_rx_interrupt,
1857 },
1858
1859 [SCIx_TXI_IRQ] = {
1860 .desc = "tx empty",
1861 .handler = sci_tx_interrupt,
1862 },
1863
1864 [SCIx_BRI_IRQ] = {
1865 .desc = "break",
1866 .handler = sci_br_interrupt,
1867 },
1868
1869 [SCIx_DRI_IRQ] = {
1870 .desc = "rx ready",
1871 .handler = sci_rx_interrupt,
1872 },
1873
1874 [SCIx_TEI_IRQ] = {
1875 .desc = "tx end",
1876 .handler = sci_tx_interrupt,
1877 },
1878
1879 /*
1880 * Special muxed handler.
1881 */
1882 [SCIx_MUX_IRQ] = {
1883 .desc = "mux",
1884 .handler = sci_mpxed_interrupt,
1885 },
1886};
1887
1888static int sci_request_irq(struct sci_port *port)
1889{
1890 struct uart_port *up = &port->port;
1891 int i, j, w, ret = 0;
1892
1893 for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
1894 const struct sci_irq_desc *desc;
1895 int irq;
1896
1897 /* Check if already registered (muxed) */
1898 for (w = 0; w < i; w++)
1899 if (port->irqs[w] == port->irqs[i])
1900 w = i + 1;
1901 if (w > i)
1902 continue;
1903
1904 if (SCIx_IRQ_IS_MUXED(port)) {
1905 i = SCIx_MUX_IRQ;
1906 irq = up->irq;
1907 } else {
1908 irq = port->irqs[i];
1909
1910 /*
1911 * Certain port types won't support all of the
1912 * available interrupt sources.
1913 */
1914 if (unlikely(irq < 0))
1915 continue;
1916 }
1917
1918 desc = sci_irq_desc + i;
1919 port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
1920 dev_name(up->dev), desc->desc);
1921 if (!port->irqstr[j]) {
1922 ret = -ENOMEM;
1923 goto out_nomem;
1924 }
1925
1926 ret = request_irq(irq, desc->handler, up->irqflags,
1927 port->irqstr[j], port);
1928 if (unlikely(ret)) {
1929 dev_err(up->dev, "Can't allocate %s IRQ\n", desc->desc);
1930 goto out_noirq;
1931 }
1932 }
1933
1934 return 0;
1935
1936out_noirq:
1937 while (--i >= 0)
1938 free_irq(port->irqs[i], port);
1939
1940out_nomem:
1941 while (--j >= 0)
1942 kfree(port->irqstr[j]);
1943
1944 return ret;
1945}
1946
1947static void sci_free_irq(struct sci_port *port)
1948{
1949 int i, j;
1950
1951 /*
1952 * Intentionally in reverse order so we iterate over the muxed
1953 * IRQ first.
1954 */
1955 for (i = 0; i < SCIx_NR_IRQS; i++) {
1956 int irq = port->irqs[i];
1957
1958 /*
1959 * Certain port types won't support all of the available
1960 * interrupt sources.
1961 */
1962 if (unlikely(irq < 0))
1963 continue;
1964
1965 /* Check if already freed (irq was muxed) */
1966 for (j = 0; j < i; j++)
1967 if (port->irqs[j] == irq)
1968 j = i + 1;
1969 if (j > i)
1970 continue;
1971
1972 free_irq(port->irqs[i], port);
1973 kfree(port->irqstr[i]);
1974
1975 if (SCIx_IRQ_IS_MUXED(port)) {
1976 /* If there's only one IRQ, we're done. */
1977 return;
1978 }
1979 }
1980}
1981
1982static unsigned int sci_tx_empty(struct uart_port *port)
1983{
1984 unsigned short status = serial_port_in(port, SCxSR);
1985 unsigned short in_tx_fifo = sci_txfill(port);
1986
1987 return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
1988}
1989
1990static void sci_set_rts(struct uart_port *port, bool state)
1991{
1992 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1993 u16 data = serial_port_in(port, SCPDR);
1994
1995 /* Active low */
1996 if (state)
1997 data &= ~SCPDR_RTSD;
1998 else
1999 data |= SCPDR_RTSD;
2000 serial_port_out(port, SCPDR, data);
2001
2002 /* RTS# is output */
2003 serial_port_out(port, SCPCR,
2004 serial_port_in(port, SCPCR) | SCPCR_RTSC);
2005 } else if (sci_getreg(port, SCSPTR)->size) {
2006 u16 ctrl = serial_port_in(port, SCSPTR);
2007
2008 /* Active low */
2009 if (state)
2010 ctrl &= ~SCSPTR_RTSDT;
2011 else
2012 ctrl |= SCSPTR_RTSDT;
2013 serial_port_out(port, SCSPTR, ctrl);
2014 }
2015}
2016
2017static bool sci_get_cts(struct uart_port *port)
2018{
2019 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
2020 /* Active low */
2021 return !(serial_port_in(port, SCPDR) & SCPDR_CTSD);
2022 } else if (sci_getreg(port, SCSPTR)->size) {
2023 /* Active low */
2024 return !(serial_port_in(port, SCSPTR) & SCSPTR_CTSDT);
2025 }
2026
2027 return true;
2028}
2029
2030/*
2031 * Modem control is a bit of a mixed bag for SCI(F) ports. Generally
2032 * CTS/RTS is supported in hardware by at least one port and controlled
2033 * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently
2034 * handled via the ->init_pins() op, which is a bit of a one-way street,
2035 * lacking any ability to defer pin control -- this will later be
2036 * converted over to the GPIO framework).
2037 *
2038 * Other modes (such as loopback) are supported generically on certain
2039 * port types, but not others. For these it's sufficient to test for the
2040 * existence of the support register and simply ignore the port type.
2041 */
2042static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
2043{
2044 struct sci_port *s = to_sci_port(port);
2045
2046 if (mctrl & TIOCM_LOOP) {
2047 const struct plat_sci_reg *reg;
2048
2049 /*
2050 * Standard loopback mode for SCFCR ports.
2051 */
2052 reg = sci_getreg(port, SCFCR);
2053 if (reg->size)
2054 serial_port_out(port, SCFCR,
2055 serial_port_in(port, SCFCR) |
2056 SCFCR_LOOP);
2057 }
2058
2059 mctrl_gpio_set(s->gpios, mctrl);
2060
2061 if (!s->has_rtscts)
2062 return;
2063
2064 if (!(mctrl & TIOCM_RTS)) {
2065 /* Disable Auto RTS */
2066 serial_port_out(port, SCFCR,
2067 serial_port_in(port, SCFCR) & ~SCFCR_MCE);
2068
2069 /* Clear RTS */
2070 sci_set_rts(port, 0);
2071 } else if (s->autorts) {
2072 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
2073 /* Enable RTS# pin function */
2074 serial_port_out(port, SCPCR,
2075 serial_port_in(port, SCPCR) & ~SCPCR_RTSC);
2076 }
2077
2078 /* Enable Auto RTS */
2079 serial_port_out(port, SCFCR,
2080 serial_port_in(port, SCFCR) | SCFCR_MCE);
2081 } else {
2082 /* Set RTS */
2083 sci_set_rts(port, 1);
2084 }
2085}
2086
2087static unsigned int sci_get_mctrl(struct uart_port *port)
2088{
2089 struct sci_port *s = to_sci_port(port);
2090 struct mctrl_gpios *gpios = s->gpios;
2091 unsigned int mctrl = 0;
2092
2093 mctrl_gpio_get(gpios, &mctrl);
2094
2095 /*
2096 * CTS/RTS is handled in hardware when supported, while nothing
2097 * else is wired up.
2098 */
2099 if (s->autorts) {
2100 if (sci_get_cts(port))
2101 mctrl |= TIOCM_CTS;
2102 } else if (!mctrl_gpio_to_gpiod(gpios, UART_GPIO_CTS)) {
2103 mctrl |= TIOCM_CTS;
2104 }
2105 if (!mctrl_gpio_to_gpiod(gpios, UART_GPIO_DSR))
2106 mctrl |= TIOCM_DSR;
2107 if (!mctrl_gpio_to_gpiod(gpios, UART_GPIO_DCD))
2108 mctrl |= TIOCM_CAR;
2109
2110 return mctrl;
2111}
2112
2113static void sci_enable_ms(struct uart_port *port)
2114{
2115 mctrl_gpio_enable_ms(to_sci_port(port)->gpios);
2116}
2117
2118static void sci_break_ctl(struct uart_port *port, int break_state)
2119{
2120 unsigned short scscr, scsptr;
2121 unsigned long flags;
2122
2123 /* check wheter the port has SCSPTR */
2124 if (!sci_getreg(port, SCSPTR)->size) {
2125 /*
2126 * Not supported by hardware. Most parts couple break and rx
2127 * interrupts together, with break detection always enabled.
2128 */
2129 return;
2130 }
2131
2132 spin_lock_irqsave(&port->lock, flags);
2133 scsptr = serial_port_in(port, SCSPTR);
2134 scscr = serial_port_in(port, SCSCR);
2135
2136 if (break_state == -1) {
2137 scsptr = (scsptr | SCSPTR_SPB2IO) & ~SCSPTR_SPB2DT;
2138 scscr &= ~SCSCR_TE;
2139 } else {
2140 scsptr = (scsptr | SCSPTR_SPB2DT) & ~SCSPTR_SPB2IO;
2141 scscr |= SCSCR_TE;
2142 }
2143
2144 serial_port_out(port, SCSPTR, scsptr);
2145 serial_port_out(port, SCSCR, scscr);
2146 spin_unlock_irqrestore(&port->lock, flags);
2147}
2148
2149static int sci_startup(struct uart_port *port)
2150{
2151 struct sci_port *s = to_sci_port(port);
2152 int ret;
2153
2154 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
2155
2156 sci_request_dma(port);
2157
2158 ret = sci_request_irq(s);
2159 if (unlikely(ret < 0)) {
2160 sci_free_dma(port);
2161 return ret;
2162 }
2163
2164 return 0;
2165}
2166
2167static void sci_shutdown(struct uart_port *port)
2168{
2169 struct sci_port *s = to_sci_port(port);
2170 unsigned long flags;
2171 u16 scr;
2172
2173 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
2174
2175 s->autorts = false;
2176 mctrl_gpio_disable_ms(to_sci_port(port)->gpios);
2177
2178 spin_lock_irqsave(&port->lock, flags);
2179 sci_stop_rx(port);
2180 sci_stop_tx(port);
2181 /*
2182 * Stop RX and TX, disable related interrupts, keep clock source
2183 * and HSCIF TOT bits
2184 */
2185 scr = serial_port_in(port, SCSCR);
2186 serial_port_out(port, SCSCR, scr &
2187 (SCSCR_CKE1 | SCSCR_CKE0 | s->hscif_tot));
2188 spin_unlock_irqrestore(&port->lock, flags);
2189
2190#ifdef CONFIG_SERIAL_SH_SCI_DMA
2191 if (s->chan_rx_saved) {
2192 dev_dbg(port->dev, "%s(%d) deleting rx_timer\n", __func__,
2193 port->line);
2194 hrtimer_cancel(&s->rx_timer);
2195 }
2196#endif
2197
2198 if (s->rx_trigger > 1 && s->rx_fifo_timeout > 0)
2199 del_timer_sync(&s->rx_fifo_timer);
2200 sci_free_irq(s);
2201 sci_free_dma(port);
2202}
2203
2204static int sci_sck_calc(struct sci_port *s, unsigned int bps,
2205 unsigned int *srr)
2206{
2207 unsigned long freq = s->clk_rates[SCI_SCK];
2208 int err, min_err = INT_MAX;
2209 unsigned int sr;
2210
2211 if (s->port.type != PORT_HSCIF)
2212 freq *= 2;
2213
2214 for_each_sr(sr, s) {
2215 err = DIV_ROUND_CLOSEST(freq, sr) - bps;
2216 if (abs(err) >= abs(min_err))
2217 continue;
2218
2219 min_err = err;
2220 *srr = sr - 1;
2221
2222 if (!err)
2223 break;
2224 }
2225
2226 dev_dbg(s->port.dev, "SCK: %u%+d bps using SR %u\n", bps, min_err,
2227 *srr + 1);
2228 return min_err;
2229}
2230
2231static int sci_brg_calc(struct sci_port *s, unsigned int bps,
2232 unsigned long freq, unsigned int *dlr,
2233 unsigned int *srr)
2234{
2235 int err, min_err = INT_MAX;
2236 unsigned int sr, dl;
2237
2238 if (s->port.type != PORT_HSCIF)
2239 freq *= 2;
2240
2241 for_each_sr(sr, s) {
2242 dl = DIV_ROUND_CLOSEST(freq, sr * bps);
2243 dl = clamp(dl, 1U, 65535U);
2244
2245 err = DIV_ROUND_CLOSEST(freq, sr * dl) - bps;
2246 if (abs(err) >= abs(min_err))
2247 continue;
2248
2249 min_err = err;
2250 *dlr = dl;
2251 *srr = sr - 1;
2252
2253 if (!err)
2254 break;
2255 }
2256
2257 dev_dbg(s->port.dev, "BRG: %u%+d bps using DL %u SR %u\n", bps,
2258 min_err, *dlr, *srr + 1);
2259 return min_err;
2260}
2261
2262/* calculate sample rate, BRR, and clock select */
2263static int sci_scbrr_calc(struct sci_port *s, unsigned int bps,
2264 unsigned int *brr, unsigned int *srr,
2265 unsigned int *cks)
2266{
2267 unsigned long freq = s->clk_rates[SCI_FCK];
2268 unsigned int sr, br, prediv, scrate, c;
2269 int err, min_err = INT_MAX;
2270
2271 if (s->port.type != PORT_HSCIF)
2272 freq *= 2;
2273
2274 /*
2275 * Find the combination of sample rate and clock select with the
2276 * smallest deviation from the desired baud rate.
2277 * Prefer high sample rates to maximise the receive margin.
2278 *
2279 * M: Receive margin (%)
2280 * N: Ratio of bit rate to clock (N = sampling rate)
2281 * D: Clock duty (D = 0 to 1.0)
2282 * L: Frame length (L = 9 to 12)
2283 * F: Absolute value of clock frequency deviation
2284 *
2285 * M = |(0.5 - 1 / 2 * N) - ((L - 0.5) * F) -
2286 * (|D - 0.5| / N * (1 + F))|
2287 * NOTE: Usually, treat D for 0.5, F is 0 by this calculation.
2288 */
2289 for_each_sr(sr, s) {
2290 for (c = 0; c <= 3; c++) {
2291 /* integerized formulas from HSCIF documentation */
2292 prediv = sr * (1 << (2 * c + 1));
2293
2294 /*
2295 * We need to calculate:
2296 *
2297 * br = freq / (prediv * bps) clamped to [1..256]
2298 * err = freq / (br * prediv) - bps
2299 *
2300 * Watch out for overflow when calculating the desired
2301 * sampling clock rate!
2302 */
2303 if (bps > UINT_MAX / prediv)
2304 break;
2305
2306 scrate = prediv * bps;
2307 br = DIV_ROUND_CLOSEST(freq, scrate);
2308 br = clamp(br, 1U, 256U);
2309
2310 err = DIV_ROUND_CLOSEST(freq, br * prediv) - bps;
2311 if (abs(err) >= abs(min_err))
2312 continue;
2313
2314 min_err = err;
2315 *brr = br - 1;
2316 *srr = sr - 1;
2317 *cks = c;
2318
2319 if (!err)
2320 goto found;
2321 }
2322 }
2323
2324found:
2325 dev_dbg(s->port.dev, "BRR: %u%+d bps using N %u SR %u cks %u\n", bps,
2326 min_err, *brr, *srr + 1, *cks);
2327 return min_err;
2328}
2329
2330static void sci_reset(struct uart_port *port)
2331{
2332 const struct plat_sci_reg *reg;
2333 unsigned int status;
2334 struct sci_port *s = to_sci_port(port);
2335
2336 serial_port_out(port, SCSCR, s->hscif_tot); /* TE=0, RE=0, CKE1=0 */
2337
2338 reg = sci_getreg(port, SCFCR);
2339 if (reg->size)
2340 serial_port_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
2341
2342 sci_clear_SCxSR(port,
2343 SCxSR_RDxF_CLEAR(port) & SCxSR_ERROR_CLEAR(port) &
2344 SCxSR_BREAK_CLEAR(port));
2345 if (sci_getreg(port, SCLSR)->size) {
2346 status = serial_port_in(port, SCLSR);
2347 status &= ~(SCLSR_TO | SCLSR_ORER);
2348 serial_port_out(port, SCLSR, status);
2349 }
2350
2351 if (s->rx_trigger > 1) {
2352 if (s->rx_fifo_timeout) {
2353 scif_set_rtrg(port, 1);
2354 timer_setup(&s->rx_fifo_timer, rx_fifo_timer_fn, 0);
2355 } else {
2356 if (port->type == PORT_SCIFA ||
2357 port->type == PORT_SCIFB)
2358 scif_set_rtrg(port, 1);
2359 else
2360 scif_set_rtrg(port, s->rx_trigger);
2361 }
2362 }
2363}
2364
2365static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
2366 struct ktermios *old)
2367{
2368 unsigned int baud, smr_val = SCSMR_ASYNC, scr_val = 0, i, bits;
2369 unsigned int brr = 255, cks = 0, srr = 15, dl = 0, sccks = 0;
2370 unsigned int brr1 = 255, cks1 = 0, srr1 = 15, dl1 = 0;
2371 struct sci_port *s = to_sci_port(port);
2372 const struct plat_sci_reg *reg;
2373 int min_err = INT_MAX, err;
2374 unsigned long max_freq = 0;
2375 int best_clk = -1;
2376 unsigned long flags;
2377
2378 if ((termios->c_cflag & CSIZE) == CS7)
2379 smr_val |= SCSMR_CHR;
2380 if (termios->c_cflag & PARENB)
2381 smr_val |= SCSMR_PE;
2382 if (termios->c_cflag & PARODD)
2383 smr_val |= SCSMR_PE | SCSMR_ODD;
2384 if (termios->c_cflag & CSTOPB)
2385 smr_val |= SCSMR_STOP;
2386
2387 /*
2388 * earlyprintk comes here early on with port->uartclk set to zero.
2389 * the clock framework is not up and running at this point so here
2390 * we assume that 115200 is the maximum baud rate. please note that
2391 * the baud rate is not programmed during earlyprintk - it is assumed
2392 * that the previous boot loader has enabled required clocks and
2393 * setup the baud rate generator hardware for us already.
2394 */
2395 if (!port->uartclk) {
2396 baud = uart_get_baud_rate(port, termios, old, 0, 115200);
2397 goto done;
2398 }
2399
2400 for (i = 0; i < SCI_NUM_CLKS; i++)
2401 max_freq = max(max_freq, s->clk_rates[i]);
2402
2403 baud = uart_get_baud_rate(port, termios, old, 0, max_freq / min_sr(s));
2404 if (!baud)
2405 goto done;
2406
2407 /*
2408 * There can be multiple sources for the sampling clock. Find the one
2409 * that gives us the smallest deviation from the desired baud rate.
2410 */
2411
2412 /* Optional Undivided External Clock */
2413 if (s->clk_rates[SCI_SCK] && port->type != PORT_SCIFA &&
2414 port->type != PORT_SCIFB) {
2415 err = sci_sck_calc(s, baud, &srr1);
2416 if (abs(err) < abs(min_err)) {
2417 best_clk = SCI_SCK;
2418 scr_val = SCSCR_CKE1;
2419 sccks = SCCKS_CKS;
2420 min_err = err;
2421 srr = srr1;
2422 if (!err)
2423 goto done;
2424 }
2425 }
2426
2427 /* Optional BRG Frequency Divided External Clock */
2428 if (s->clk_rates[SCI_SCIF_CLK] && sci_getreg(port, SCDL)->size) {
2429 err = sci_brg_calc(s, baud, s->clk_rates[SCI_SCIF_CLK], &dl1,
2430 &srr1);
2431 if (abs(err) < abs(min_err)) {
2432 best_clk = SCI_SCIF_CLK;
2433 scr_val = SCSCR_CKE1;
2434 sccks = 0;
2435 min_err = err;
2436 dl = dl1;
2437 srr = srr1;
2438 if (!err)
2439 goto done;
2440 }
2441 }
2442
2443 /* Optional BRG Frequency Divided Internal Clock */
2444 if (s->clk_rates[SCI_BRG_INT] && sci_getreg(port, SCDL)->size) {
2445 err = sci_brg_calc(s, baud, s->clk_rates[SCI_BRG_INT], &dl1,
2446 &srr1);
2447 if (abs(err) < abs(min_err)) {
2448 best_clk = SCI_BRG_INT;
2449 scr_val = SCSCR_CKE1;
2450 sccks = SCCKS_XIN;
2451 min_err = err;
2452 dl = dl1;
2453 srr = srr1;
2454 if (!min_err)
2455 goto done;
2456 }
2457 }
2458
2459 /* Divided Functional Clock using standard Bit Rate Register */
2460 err = sci_scbrr_calc(s, baud, &brr1, &srr1, &cks1);
2461 if (abs(err) < abs(min_err)) {
2462 best_clk = SCI_FCK;
2463 scr_val = 0;
2464 min_err = err;
2465 brr = brr1;
2466 srr = srr1;
2467 cks = cks1;
2468 }
2469
2470done:
2471 if (best_clk >= 0)
2472 dev_dbg(port->dev, "Using clk %pC for %u%+d bps\n",
2473 s->clks[best_clk], baud, min_err);
2474
2475 sci_port_enable(s);
2476
2477 /*
2478 * Program the optional External Baud Rate Generator (BRG) first.
2479 * It controls the mux to select (H)SCK or frequency divided clock.
2480 */
2481 if (best_clk >= 0 && sci_getreg(port, SCCKS)->size) {
2482 serial_port_out(port, SCDL, dl);
2483 serial_port_out(port, SCCKS, sccks);
2484 }
2485
2486 spin_lock_irqsave(&port->lock, flags);
2487
2488 sci_reset(port);
2489
2490 uart_update_timeout(port, termios->c_cflag, baud);
2491
2492 /* byte size and parity */
2493 switch (termios->c_cflag & CSIZE) {
2494 case CS5:
2495 bits = 7;
2496 break;
2497 case CS6:
2498 bits = 8;
2499 break;
2500 case CS7:
2501 bits = 9;
2502 break;
2503 default:
2504 bits = 10;
2505 break;
2506 }
2507
2508 if (termios->c_cflag & CSTOPB)
2509 bits++;
2510 if (termios->c_cflag & PARENB)
2511 bits++;
2512
2513 if (best_clk >= 0) {
2514 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
2515 switch (srr + 1) {
2516 case 5: smr_val |= SCSMR_SRC_5; break;
2517 case 7: smr_val |= SCSMR_SRC_7; break;
2518 case 11: smr_val |= SCSMR_SRC_11; break;
2519 case 13: smr_val |= SCSMR_SRC_13; break;
2520 case 16: smr_val |= SCSMR_SRC_16; break;
2521 case 17: smr_val |= SCSMR_SRC_17; break;
2522 case 19: smr_val |= SCSMR_SRC_19; break;
2523 case 27: smr_val |= SCSMR_SRC_27; break;
2524 }
2525 smr_val |= cks;
2526 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
2527 serial_port_out(port, SCSMR, smr_val);
2528 serial_port_out(port, SCBRR, brr);
2529 if (sci_getreg(port, HSSRR)->size) {
2530 unsigned int hssrr = srr | HSCIF_SRE;
2531 /* Calculate deviation from intended rate at the
2532 * center of the last stop bit in sampling clocks.
2533 */
2534 int last_stop = bits * 2 - 1;
2535 int deviation = DIV_ROUND_CLOSEST(min_err * last_stop *
2536 (int)(srr + 1),
2537 2 * (int)baud);
2538
2539 if (abs(deviation) >= 2) {
2540 /* At least two sampling clocks off at the
2541 * last stop bit; we can increase the error
2542 * margin by shifting the sampling point.
2543 */
2544 int shift = clamp(deviation / 2, -8, 7);
2545
2546 hssrr |= (shift << HSCIF_SRHP_SHIFT) &
2547 HSCIF_SRHP_MASK;
2548 hssrr |= HSCIF_SRDE;
2549 }
2550 serial_port_out(port, HSSRR, hssrr);
2551 }
2552
2553 /* Wait one bit interval */
2554 udelay((1000000 + (baud - 1)) / baud);
2555 } else {
2556 /* Don't touch the bit rate configuration */
2557 scr_val = s->cfg->scscr & (SCSCR_CKE1 | SCSCR_CKE0);
2558 smr_val |= serial_port_in(port, SCSMR) &
2559 (SCSMR_CKEDG | SCSMR_SRC_MASK | SCSMR_CKS);
2560 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
2561 serial_port_out(port, SCSMR, smr_val);
2562 }
2563
2564 sci_init_pins(port, termios->c_cflag);
2565
2566 port->status &= ~UPSTAT_AUTOCTS;
2567 s->autorts = false;
2568 reg = sci_getreg(port, SCFCR);
2569 if (reg->size) {
2570 unsigned short ctrl = serial_port_in(port, SCFCR);
2571
2572 if ((port->flags & UPF_HARD_FLOW) &&
2573 (termios->c_cflag & CRTSCTS)) {
2574 /* There is no CTS interrupt to restart the hardware */
2575 port->status |= UPSTAT_AUTOCTS;
2576 /* MCE is enabled when RTS is raised */
2577 s->autorts = true;
2578 }
2579
2580 /*
2581 * As we've done a sci_reset() above, ensure we don't
2582 * interfere with the FIFOs while toggling MCE. As the
2583 * reset values could still be set, simply mask them out.
2584 */
2585 ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST);
2586
2587 serial_port_out(port, SCFCR, ctrl);
2588 }
2589 if (port->flags & UPF_HARD_FLOW) {
2590 /* Refresh (Auto) RTS */
2591 sci_set_mctrl(port, port->mctrl);
2592 }
2593
2594 scr_val |= SCSCR_RE | SCSCR_TE |
2595 (s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0));
2596 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
2597 if ((srr + 1 == 5) &&
2598 (port->type == PORT_SCIFA || port->type == PORT_SCIFB)) {
2599 /*
2600 * In asynchronous mode, when the sampling rate is 1/5, first
2601 * received data may become invalid on some SCIFA and SCIFB.
2602 * To avoid this problem wait more than 1 serial data time (1
2603 * bit time x serial data number) after setting SCSCR.RE = 1.
2604 */
2605 udelay(DIV_ROUND_UP(10 * 1000000, baud));
2606 }
2607
2608 /*
2609 * Calculate delay for 2 DMA buffers (4 FIFO).
2610 * See serial_core.c::uart_update_timeout().
2611 * With 10 bits (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above
2612 * function calculates 1 jiffie for the data plus 5 jiffies for the
2613 * "slop(e)." Then below we calculate 5 jiffies (20ms) for 2 DMA
2614 * buffers (4 FIFO sizes), but when performing a faster transfer, the
2615 * value obtained by this formula is too small. Therefore, if the value
2616 * is smaller than 20ms, use 20ms as the timeout value for DMA.
2617 */
2618 s->rx_frame = (10000 * bits) / (baud / 100);
2619#ifdef CONFIG_SERIAL_SH_SCI_DMA
2620 s->rx_timeout = s->buf_len_rx * 2 * s->rx_frame;
2621 if (s->rx_timeout < 20)
2622 s->rx_timeout = 20;
2623#endif
2624
2625 if ((termios->c_cflag & CREAD) != 0)
2626 sci_start_rx(port);
2627
2628 spin_unlock_irqrestore(&port->lock, flags);
2629
2630 sci_port_disable(s);
2631
2632 if (UART_ENABLE_MS(port, termios->c_cflag))
2633 sci_enable_ms(port);
2634}
2635
2636static void sci_pm(struct uart_port *port, unsigned int state,
2637 unsigned int oldstate)
2638{
2639 struct sci_port *sci_port = to_sci_port(port);
2640
2641 switch (state) {
2642 case UART_PM_STATE_OFF:
2643 sci_port_disable(sci_port);
2644 break;
2645 default:
2646 sci_port_enable(sci_port);
2647 break;
2648 }
2649}
2650
2651static const char *sci_type(struct uart_port *port)
2652{
2653 switch (port->type) {
2654 case PORT_IRDA:
2655 return "irda";
2656 case PORT_SCI:
2657 return "sci";
2658 case PORT_SCIF:
2659 return "scif";
2660 case PORT_SCIFA:
2661 return "scifa";
2662 case PORT_SCIFB:
2663 return "scifb";
2664 case PORT_HSCIF:
2665 return "hscif";
2666 }
2667
2668 return NULL;
2669}
2670
2671static int sci_remap_port(struct uart_port *port)
2672{
2673 struct sci_port *sport = to_sci_port(port);
2674
2675 /*
2676 * Nothing to do if there's already an established membase.
2677 */
2678 if (port->membase)
2679 return 0;
2680
2681 if (port->dev->of_node || (port->flags & UPF_IOREMAP)) {
2682 port->membase = ioremap_nocache(port->mapbase, sport->reg_size);
2683 if (unlikely(!port->membase)) {
2684 dev_err(port->dev, "can't remap port#%d\n", port->line);
2685 return -ENXIO;
2686 }
2687 } else {
2688 /*
2689 * For the simple (and majority of) cases where we don't
2690 * need to do any remapping, just cast the cookie
2691 * directly.
2692 */
2693 port->membase = (void __iomem *)(uintptr_t)port->mapbase;
2694 }
2695
2696 return 0;
2697}
2698
2699static void sci_release_port(struct uart_port *port)
2700{
2701 struct sci_port *sport = to_sci_port(port);
2702
2703 if (port->dev->of_node || (port->flags & UPF_IOREMAP)) {
2704 iounmap(port->membase);
2705 port->membase = NULL;
2706 }
2707
2708 release_mem_region(port->mapbase, sport->reg_size);
2709}
2710
2711static int sci_request_port(struct uart_port *port)
2712{
2713 struct resource *res;
2714 struct sci_port *sport = to_sci_port(port);
2715 int ret;
2716
2717 res = request_mem_region(port->mapbase, sport->reg_size,
2718 dev_name(port->dev));
2719 if (unlikely(res == NULL)) {
2720 dev_err(port->dev, "request_mem_region failed.");
2721 return -EBUSY;
2722 }
2723
2724 ret = sci_remap_port(port);
2725 if (unlikely(ret != 0)) {
2726 release_resource(res);
2727 return ret;
2728 }
2729
2730 return 0;
2731}
2732
2733static void sci_config_port(struct uart_port *port, int flags)
2734{
2735 if (flags & UART_CONFIG_TYPE) {
2736 struct sci_port *sport = to_sci_port(port);
2737
2738 port->type = sport->cfg->type;
2739 sci_request_port(port);
2740 }
2741}
2742
2743static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
2744{
2745 if (ser->baud_base < 2400)
2746 /* No paper tape reader for Mitch.. */
2747 return -EINVAL;
2748
2749 return 0;
2750}
2751
2752static const struct uart_ops sci_uart_ops = {
2753 .tx_empty = sci_tx_empty,
2754 .set_mctrl = sci_set_mctrl,
2755 .get_mctrl = sci_get_mctrl,
2756 .start_tx = sci_start_tx,
2757 .stop_tx = sci_stop_tx,
2758 .stop_rx = sci_stop_rx,
2759 .enable_ms = sci_enable_ms,
2760 .break_ctl = sci_break_ctl,
2761 .startup = sci_startup,
2762 .shutdown = sci_shutdown,
2763 .flush_buffer = sci_flush_buffer,
2764 .set_termios = sci_set_termios,
2765 .pm = sci_pm,
2766 .type = sci_type,
2767 .release_port = sci_release_port,
2768 .request_port = sci_request_port,
2769 .config_port = sci_config_port,
2770 .verify_port = sci_verify_port,
2771#ifdef CONFIG_CONSOLE_POLL
2772 .poll_get_char = sci_poll_get_char,
2773 .poll_put_char = sci_poll_put_char,
2774#endif
2775};
2776
2777static int sci_init_clocks(struct sci_port *sci_port, struct device *dev)
2778{
2779 const char *clk_names[] = {
2780 [SCI_FCK] = "fck",
2781 [SCI_SCK] = "sck",
2782 [SCI_BRG_INT] = "brg_int",
2783 [SCI_SCIF_CLK] = "scif_clk",
2784 };
2785 struct clk *clk;
2786 unsigned int i;
2787
2788 if (sci_port->cfg->type == PORT_HSCIF)
2789 clk_names[SCI_SCK] = "hsck";
2790
2791 for (i = 0; i < SCI_NUM_CLKS; i++) {
2792 clk = devm_clk_get(dev, clk_names[i]);
2793 if (PTR_ERR(clk) == -EPROBE_DEFER)
2794 return -EPROBE_DEFER;
2795
2796 if (IS_ERR(clk) && i == SCI_FCK) {
2797 /*
2798 * "fck" used to be called "sci_ick", and we need to
2799 * maintain DT backward compatibility.
2800 */
2801 clk = devm_clk_get(dev, "sci_ick");
2802 if (PTR_ERR(clk) == -EPROBE_DEFER)
2803 return -EPROBE_DEFER;
2804
2805 if (!IS_ERR(clk))
2806 goto found;
2807
2808 /*
2809 * Not all SH platforms declare a clock lookup entry
2810 * for SCI devices, in which case we need to get the
2811 * global "peripheral_clk" clock.
2812 */
2813 clk = devm_clk_get(dev, "peripheral_clk");
2814 if (!IS_ERR(clk))
2815 goto found;
2816
2817 dev_err(dev, "failed to get %s (%ld)\n", clk_names[i],
2818 PTR_ERR(clk));
2819 return PTR_ERR(clk);
2820 }
2821
2822found:
2823 if (IS_ERR(clk))
2824 dev_dbg(dev, "failed to get %s (%ld)\n", clk_names[i],
2825 PTR_ERR(clk));
2826 else
2827 dev_dbg(dev, "clk %s is %pC rate %lu\n", clk_names[i],
2828 clk, clk_get_rate(clk));
2829 sci_port->clks[i] = IS_ERR(clk) ? NULL : clk;
2830 }
2831 return 0;
2832}
2833
2834static const struct sci_port_params *
2835sci_probe_regmap(const struct plat_sci_port *cfg)
2836{
2837 unsigned int regtype;
2838
2839 if (cfg->regtype != SCIx_PROBE_REGTYPE)
2840 return &sci_port_params[cfg->regtype];
2841
2842 switch (cfg->type) {
2843 case PORT_SCI:
2844 regtype = SCIx_SCI_REGTYPE;
2845 break;
2846 case PORT_IRDA:
2847 regtype = SCIx_IRDA_REGTYPE;
2848 break;
2849 case PORT_SCIFA:
2850 regtype = SCIx_SCIFA_REGTYPE;
2851 break;
2852 case PORT_SCIFB:
2853 regtype = SCIx_SCIFB_REGTYPE;
2854 break;
2855 case PORT_SCIF:
2856 /*
2857 * The SH-4 is a bit of a misnomer here, although that's
2858 * where this particular port layout originated. This
2859 * configuration (or some slight variation thereof)
2860 * remains the dominant model for all SCIFs.
2861 */
2862 regtype = SCIx_SH4_SCIF_REGTYPE;
2863 break;
2864 case PORT_HSCIF:
2865 regtype = SCIx_HSCIF_REGTYPE;
2866 break;
2867 default:
2868 pr_err("Can't probe register map for given port\n");
2869 return NULL;
2870 }
2871
2872 return &sci_port_params[regtype];
2873}
2874
2875static int sci_init_single(struct platform_device *dev,
2876 struct sci_port *sci_port, unsigned int index,
2877 const struct plat_sci_port *p, bool early)
2878{
2879 struct uart_port *port = &sci_port->port;
2880 const struct resource *res;
2881 unsigned int i;
2882 int ret;
2883
2884 sci_port->cfg = p;
2885
2886 port->ops = &sci_uart_ops;
2887 port->iotype = UPIO_MEM;
2888 port->line = index;
2889
2890 res = platform_get_resource(dev, IORESOURCE_MEM, 0);
2891 if (res == NULL)
2892 return -ENOMEM;
2893
2894 port->mapbase = res->start;
2895 sci_port->reg_size = resource_size(res);
2896
2897 for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i) {
2898 if (i)
2899 sci_port->irqs[i] = platform_get_irq_optional(dev, i);
2900 else
2901 sci_port->irqs[i] = platform_get_irq(dev, i);
2902 }
2903
2904 /* The SCI generates several interrupts. They can be muxed together or
2905 * connected to different interrupt lines. In the muxed case only one
2906 * interrupt resource is specified as there is only one interrupt ID.
2907 * In the non-muxed case, up to 6 interrupt signals might be generated
2908 * from the SCI, however those signals might have their own individual
2909 * interrupt ID numbers, or muxed together with another interrupt.
2910 */
2911 if (sci_port->irqs[0] < 0)
2912 return -ENXIO;
2913
2914 if (sci_port->irqs[1] < 0)
2915 for (i = 1; i < ARRAY_SIZE(sci_port->irqs); i++)
2916 sci_port->irqs[i] = sci_port->irqs[0];
2917
2918 sci_port->params = sci_probe_regmap(p);
2919 if (unlikely(sci_port->params == NULL))
2920 return -EINVAL;
2921
2922 switch (p->type) {
2923 case PORT_SCIFB:
2924 sci_port->rx_trigger = 48;
2925 break;
2926 case PORT_HSCIF:
2927 sci_port->rx_trigger = 64;
2928 break;
2929 case PORT_SCIFA:
2930 sci_port->rx_trigger = 32;
2931 break;
2932 case PORT_SCIF:
2933 if (p->regtype == SCIx_SH7705_SCIF_REGTYPE)
2934 /* RX triggering not implemented for this IP */
2935 sci_port->rx_trigger = 1;
2936 else
2937 sci_port->rx_trigger = 8;
2938 break;
2939 default:
2940 sci_port->rx_trigger = 1;
2941 break;
2942 }
2943
2944 sci_port->rx_fifo_timeout = 0;
2945 sci_port->hscif_tot = 0;
2946
2947 /* SCIFA on sh7723 and sh7724 need a custom sampling rate that doesn't
2948 * match the SoC datasheet, this should be investigated. Let platform
2949 * data override the sampling rate for now.
2950 */
2951 sci_port->sampling_rate_mask = p->sampling_rate
2952 ? SCI_SR(p->sampling_rate)
2953 : sci_port->params->sampling_rate_mask;
2954
2955 if (!early) {
2956 ret = sci_init_clocks(sci_port, &dev->dev);
2957 if (ret < 0)
2958 return ret;
2959
2960 port->dev = &dev->dev;
2961
2962 pm_runtime_enable(&dev->dev);
2963 }
2964
2965 port->type = p->type;
2966 port->flags = UPF_FIXED_PORT | UPF_BOOT_AUTOCONF | p->flags;
2967 port->fifosize = sci_port->params->fifosize;
2968
2969 if (port->type == PORT_SCI) {
2970 if (sci_port->reg_size >= 0x20)
2971 port->regshift = 2;
2972 else
2973 port->regshift = 1;
2974 }
2975
2976 /*
2977 * The UART port needs an IRQ value, so we peg this to the RX IRQ
2978 * for the multi-IRQ ports, which is where we are primarily
2979 * concerned with the shutdown path synchronization.
2980 *
2981 * For the muxed case there's nothing more to do.
2982 */
2983 port->irq = sci_port->irqs[SCIx_RXI_IRQ];
2984 port->irqflags = 0;
2985
2986 port->serial_in = sci_serial_in;
2987 port->serial_out = sci_serial_out;
2988
2989 return 0;
2990}
2991
2992static void sci_cleanup_single(struct sci_port *port)
2993{
2994 pm_runtime_disable(port->port.dev);
2995}
2996
2997#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \
2998 defined(CONFIG_SERIAL_SH_SCI_EARLYCON)
2999static void serial_console_putchar(struct uart_port *port, int ch)
3000{
3001 sci_poll_put_char(port, ch);
3002}
3003
3004/*
3005 * Print a string to the serial port trying not to disturb
3006 * any possible real use of the port...
3007 */
3008static void serial_console_write(struct console *co, const char *s,
3009 unsigned count)
3010{
3011 struct sci_port *sci_port = &sci_ports[co->index];
3012 struct uart_port *port = &sci_port->port;
3013 unsigned short bits, ctrl, ctrl_temp;
3014 unsigned long flags;
3015 int locked = 1;
3016
3017#if defined(SUPPORT_SYSRQ)
3018 if (port->sysrq)
3019 locked = 0;
3020 else
3021#endif
3022 if (oops_in_progress)
3023 locked = spin_trylock_irqsave(&port->lock, flags);
3024 else
3025 spin_lock_irqsave(&port->lock, flags);
3026
3027 /* first save SCSCR then disable interrupts, keep clock source */
3028 ctrl = serial_port_in(port, SCSCR);
3029 ctrl_temp = SCSCR_RE | SCSCR_TE |
3030 (sci_port->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0)) |
3031 (ctrl & (SCSCR_CKE1 | SCSCR_CKE0));
3032 serial_port_out(port, SCSCR, ctrl_temp | sci_port->hscif_tot);
3033
3034 uart_console_write(port, s, count, serial_console_putchar);
3035
3036 /* wait until fifo is empty and last bit has been transmitted */
3037 bits = SCxSR_TDxE(port) | SCxSR_TEND(port);
3038 while ((serial_port_in(port, SCxSR) & bits) != bits)
3039 cpu_relax();
3040
3041 /* restore the SCSCR */
3042 serial_port_out(port, SCSCR, ctrl);
3043
3044 if (locked)
3045 spin_unlock_irqrestore(&port->lock, flags);
3046}
3047
3048static int serial_console_setup(struct console *co, char *options)
3049{
3050 struct sci_port *sci_port;
3051 struct uart_port *port;
3052 int baud = 115200;
3053 int bits = 8;
3054 int parity = 'n';
3055 int flow = 'n';
3056 int ret;
3057
3058 /*
3059 * Refuse to handle any bogus ports.
3060 */
3061 if (co->index < 0 || co->index >= SCI_NPORTS)
3062 return -ENODEV;
3063
3064 sci_port = &sci_ports[co->index];
3065 port = &sci_port->port;
3066
3067 /*
3068 * Refuse to handle uninitialized ports.
3069 */
3070 if (!port->ops)
3071 return -ENODEV;
3072
3073 ret = sci_remap_port(port);
3074 if (unlikely(ret != 0))
3075 return ret;
3076
3077 if (options)
3078 uart_parse_options(options, &baud, &parity, &bits, &flow);
3079
3080 return uart_set_options(port, co, baud, parity, bits, flow);
3081}
3082
3083static struct console serial_console = {
3084 .name = "ttySC",
3085 .device = uart_console_device,
3086 .write = serial_console_write,
3087 .setup = serial_console_setup,
3088 .flags = CON_PRINTBUFFER,
3089 .index = -1,
3090 .data = &sci_uart_driver,
3091};
3092
3093static struct console early_serial_console = {
3094 .name = "early_ttySC",
3095 .write = serial_console_write,
3096 .flags = CON_PRINTBUFFER,
3097 .index = -1,
3098};
3099
3100static char early_serial_buf[32];
3101
3102static int sci_probe_earlyprintk(struct platform_device *pdev)
3103{
3104 const struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev);
3105
3106 if (early_serial_console.data)
3107 return -EEXIST;
3108
3109 early_serial_console.index = pdev->id;
3110
3111 sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true);
3112
3113 serial_console_setup(&early_serial_console, early_serial_buf);
3114
3115 if (!strstr(early_serial_buf, "keep"))
3116 early_serial_console.flags |= CON_BOOT;
3117
3118 register_console(&early_serial_console);
3119 return 0;
3120}
3121
3122#define SCI_CONSOLE (&serial_console)
3123
3124#else
3125static inline int sci_probe_earlyprintk(struct platform_device *pdev)
3126{
3127 return -EINVAL;
3128}
3129
3130#define SCI_CONSOLE NULL
3131
3132#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE || CONFIG_SERIAL_SH_SCI_EARLYCON */
3133
3134static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized";
3135
3136static DEFINE_MUTEX(sci_uart_registration_lock);
3137static struct uart_driver sci_uart_driver = {
3138 .owner = THIS_MODULE,
3139 .driver_name = "sci",
3140 .dev_name = "ttySC",
3141 .major = SCI_MAJOR,
3142 .minor = SCI_MINOR_START,
3143 .nr = SCI_NPORTS,
3144 .cons = SCI_CONSOLE,
3145};
3146
3147static int sci_remove(struct platform_device *dev)
3148{
3149 struct sci_port *port = platform_get_drvdata(dev);
3150 unsigned int type = port->port.type; /* uart_remove_... clears it */
3151
3152 sci_ports_in_use &= ~BIT(port->port.line);
3153 uart_remove_one_port(&sci_uart_driver, &port->port);
3154
3155 sci_cleanup_single(port);
3156
3157 if (port->port.fifosize > 1)
3158 device_remove_file(&dev->dev, &dev_attr_rx_fifo_trigger);
3159 if (type == PORT_SCIFA || type == PORT_SCIFB || type == PORT_HSCIF)
3160 device_remove_file(&dev->dev, &dev_attr_rx_fifo_timeout);
3161
3162 return 0;
3163}
3164
3165
3166#define SCI_OF_DATA(type, regtype) (void *)((type) << 16 | (regtype))
3167#define SCI_OF_TYPE(data) ((unsigned long)(data) >> 16)
3168#define SCI_OF_REGTYPE(data) ((unsigned long)(data) & 0xffff)
3169
3170static const struct of_device_id of_sci_match[] = {
3171 /* SoC-specific types */
3172 {
3173 .compatible = "renesas,scif-r7s72100",
3174 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH2_SCIF_FIFODATA_REGTYPE),
3175 },
3176 {
3177 .compatible = "renesas,scif-r7s9210",
3178 .data = SCI_OF_DATA(PORT_SCIF, SCIx_RZ_SCIFA_REGTYPE),
3179 },
3180 /* Family-specific types */
3181 {
3182 .compatible = "renesas,rcar-gen1-scif",
3183 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
3184 }, {
3185 .compatible = "renesas,rcar-gen2-scif",
3186 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
3187 }, {
3188 .compatible = "renesas,rcar-gen3-scif",
3189 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
3190 },
3191 /* Generic types */
3192 {
3193 .compatible = "renesas,scif",
3194 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_REGTYPE),
3195 }, {
3196 .compatible = "renesas,scifa",
3197 .data = SCI_OF_DATA(PORT_SCIFA, SCIx_SCIFA_REGTYPE),
3198 }, {
3199 .compatible = "renesas,scifb",
3200 .data = SCI_OF_DATA(PORT_SCIFB, SCIx_SCIFB_REGTYPE),
3201 }, {
3202 .compatible = "renesas,hscif",
3203 .data = SCI_OF_DATA(PORT_HSCIF, SCIx_HSCIF_REGTYPE),
3204 }, {
3205 .compatible = "renesas,sci",
3206 .data = SCI_OF_DATA(PORT_SCI, SCIx_SCI_REGTYPE),
3207 }, {
3208 /* Terminator */
3209 },
3210};
3211MODULE_DEVICE_TABLE(of, of_sci_match);
3212
3213static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev,
3214 unsigned int *dev_id)
3215{
3216 struct device_node *np = pdev->dev.of_node;
3217 struct plat_sci_port *p;
3218 struct sci_port *sp;
3219 const void *data;
3220 int id;
3221
3222 if (!IS_ENABLED(CONFIG_OF) || !np)
3223 return NULL;
3224
3225 data = of_device_get_match_data(&pdev->dev);
3226
3227 p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
3228 if (!p)
3229 return NULL;
3230
3231 /* Get the line number from the aliases node. */
3232 id = of_alias_get_id(np, "serial");
3233 if (id < 0 && ~sci_ports_in_use)
3234 id = ffz(sci_ports_in_use);
3235 if (id < 0) {
3236 dev_err(&pdev->dev, "failed to get alias id (%d)\n", id);
3237 return NULL;
3238 }
3239 if (id >= ARRAY_SIZE(sci_ports)) {
3240 dev_err(&pdev->dev, "serial%d out of range\n", id);
3241 return NULL;
3242 }
3243
3244 sp = &sci_ports[id];
3245 *dev_id = id;
3246
3247 p->type = SCI_OF_TYPE(data);
3248 p->regtype = SCI_OF_REGTYPE(data);
3249
3250 sp->has_rtscts = of_property_read_bool(np, "uart-has-rtscts");
3251
3252 return p;
3253}
3254
3255static int sci_probe_single(struct platform_device *dev,
3256 unsigned int index,
3257 struct plat_sci_port *p,
3258 struct sci_port *sciport)
3259{
3260 int ret;
3261
3262 /* Sanity check */
3263 if (unlikely(index >= SCI_NPORTS)) {
3264 dev_notice(&dev->dev, "Attempting to register port %d when only %d are available\n",
3265 index+1, SCI_NPORTS);
3266 dev_notice(&dev->dev, "Consider bumping CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
3267 return -EINVAL;
3268 }
3269 BUILD_BUG_ON(SCI_NPORTS > sizeof(sci_ports_in_use) * 8);
3270 if (sci_ports_in_use & BIT(index))
3271 return -EBUSY;
3272
3273 mutex_lock(&sci_uart_registration_lock);
3274 if (!sci_uart_driver.state) {
3275 ret = uart_register_driver(&sci_uart_driver);
3276 if (ret) {
3277 mutex_unlock(&sci_uart_registration_lock);
3278 return ret;
3279 }
3280 }
3281 mutex_unlock(&sci_uart_registration_lock);
3282
3283 ret = sci_init_single(dev, sciport, index, p, false);
3284 if (ret)
3285 return ret;
3286
3287 sciport->gpios = mctrl_gpio_init(&sciport->port, 0);
3288 if (IS_ERR(sciport->gpios))
3289 return PTR_ERR(sciport->gpios);
3290
3291 if (sciport->has_rtscts) {
3292 if (mctrl_gpio_to_gpiod(sciport->gpios, UART_GPIO_CTS) ||
3293 mctrl_gpio_to_gpiod(sciport->gpios, UART_GPIO_RTS)) {
3294 dev_err(&dev->dev, "Conflicting RTS/CTS config\n");
3295 return -EINVAL;
3296 }
3297 sciport->port.flags |= UPF_HARD_FLOW;
3298 }
3299
3300 ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
3301 if (ret) {
3302 sci_cleanup_single(sciport);
3303 return ret;
3304 }
3305
3306 return 0;
3307}
3308
3309static int sci_probe(struct platform_device *dev)
3310{
3311 struct plat_sci_port *p;
3312 struct sci_port *sp;
3313 unsigned int dev_id;
3314 int ret;
3315
3316 /*
3317 * If we've come here via earlyprintk initialization, head off to
3318 * the special early probe. We don't have sufficient device state
3319 * to make it beyond this yet.
3320 */
3321 if (is_early_platform_device(dev))
3322 return sci_probe_earlyprintk(dev);
3323
3324 if (dev->dev.of_node) {
3325 p = sci_parse_dt(dev, &dev_id);
3326 if (p == NULL)
3327 return -EINVAL;
3328 } else {
3329 p = dev->dev.platform_data;
3330 if (p == NULL) {
3331 dev_err(&dev->dev, "no platform data supplied\n");
3332 return -EINVAL;
3333 }
3334
3335 dev_id = dev->id;
3336 }
3337
3338 sp = &sci_ports[dev_id];
3339 platform_set_drvdata(dev, sp);
3340
3341 ret = sci_probe_single(dev, dev_id, p, sp);
3342 if (ret)
3343 return ret;
3344
3345 if (sp->port.fifosize > 1) {
3346 ret = device_create_file(&dev->dev, &dev_attr_rx_fifo_trigger);
3347 if (ret)
3348 return ret;
3349 }
3350 if (sp->port.type == PORT_SCIFA || sp->port.type == PORT_SCIFB ||
3351 sp->port.type == PORT_HSCIF) {
3352 ret = device_create_file(&dev->dev, &dev_attr_rx_fifo_timeout);
3353 if (ret) {
3354 if (sp->port.fifosize > 1) {
3355 device_remove_file(&dev->dev,
3356 &dev_attr_rx_fifo_trigger);
3357 }
3358 return ret;
3359 }
3360 }
3361
3362#ifdef CONFIG_SH_STANDARD_BIOS
3363 sh_bios_gdb_detach();
3364#endif
3365
3366 sci_ports_in_use |= BIT(dev_id);
3367 return 0;
3368}
3369
3370static __maybe_unused int sci_suspend(struct device *dev)
3371{
3372 struct sci_port *sport = dev_get_drvdata(dev);
3373
3374 if (sport)
3375 uart_suspend_port(&sci_uart_driver, &sport->port);
3376
3377 return 0;
3378}
3379
3380static __maybe_unused int sci_resume(struct device *dev)
3381{
3382 struct sci_port *sport = dev_get_drvdata(dev);
3383
3384 if (sport)
3385 uart_resume_port(&sci_uart_driver, &sport->port);
3386
3387 return 0;
3388}
3389
3390static SIMPLE_DEV_PM_OPS(sci_dev_pm_ops, sci_suspend, sci_resume);
3391
3392static struct platform_driver sci_driver = {
3393 .probe = sci_probe,
3394 .remove = sci_remove,
3395 .driver = {
3396 .name = "sh-sci",
3397 .pm = &sci_dev_pm_ops,
3398 .of_match_table = of_match_ptr(of_sci_match),
3399 },
3400};
3401
3402static int __init sci_init(void)
3403{
3404 pr_info("%s\n", banner);
3405
3406 return platform_driver_register(&sci_driver);
3407}
3408
3409static void __exit sci_exit(void)
3410{
3411 platform_driver_unregister(&sci_driver);
3412
3413 if (sci_uart_driver.state)
3414 uart_unregister_driver(&sci_uart_driver);
3415}
3416
3417#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
3418early_platform_init_buffer("earlyprintk", &sci_driver,
3419 early_serial_buf, ARRAY_SIZE(early_serial_buf));
3420#endif
3421#ifdef CONFIG_SERIAL_SH_SCI_EARLYCON
3422static struct plat_sci_port port_cfg __initdata;
3423
3424static int __init early_console_setup(struct earlycon_device *device,
3425 int type)
3426{
3427 if (!device->port.membase)
3428 return -ENODEV;
3429
3430 device->port.serial_in = sci_serial_in;
3431 device->port.serial_out = sci_serial_out;
3432 device->port.type = type;
3433 memcpy(&sci_ports[0].port, &device->port, sizeof(struct uart_port));
3434 port_cfg.type = type;
3435 sci_ports[0].cfg = &port_cfg;
3436 sci_ports[0].params = sci_probe_regmap(&port_cfg);
3437 port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR);
3438 sci_serial_out(&sci_ports[0].port, SCSCR,
3439 SCSCR_RE | SCSCR_TE | port_cfg.scscr);
3440
3441 device->con->write = serial_console_write;
3442 return 0;
3443}
3444static int __init sci_early_console_setup(struct earlycon_device *device,
3445 const char *opt)
3446{
3447 return early_console_setup(device, PORT_SCI);
3448}
3449static int __init scif_early_console_setup(struct earlycon_device *device,
3450 const char *opt)
3451{
3452 return early_console_setup(device, PORT_SCIF);
3453}
3454static int __init rzscifa_early_console_setup(struct earlycon_device *device,
3455 const char *opt)
3456{
3457 port_cfg.regtype = SCIx_RZ_SCIFA_REGTYPE;
3458 return early_console_setup(device, PORT_SCIF);
3459}
3460static int __init scifa_early_console_setup(struct earlycon_device *device,
3461 const char *opt)
3462{
3463 return early_console_setup(device, PORT_SCIFA);
3464}
3465static int __init scifb_early_console_setup(struct earlycon_device *device,
3466 const char *opt)
3467{
3468 return early_console_setup(device, PORT_SCIFB);
3469}
3470static int __init hscif_early_console_setup(struct earlycon_device *device,
3471 const char *opt)
3472{
3473 return early_console_setup(device, PORT_HSCIF);
3474}
3475
3476OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup);
3477OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup);
3478OF_EARLYCON_DECLARE(scif, "renesas,scif-r7s9210", rzscifa_early_console_setup);
3479OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup);
3480OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup);
3481OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup);
3482#endif /* CONFIG_SERIAL_SH_SCI_EARLYCON */
3483
3484module_init(sci_init);
3485module_exit(sci_exit);
3486
3487MODULE_LICENSE("GPL");
3488MODULE_ALIAS("platform:sh-sci");
3489MODULE_AUTHOR("Paul Mundt");
3490MODULE_DESCRIPTION("SuperH (H)SCI(F) serial driver");
1/*
2 * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
3 *
4 * Copyright (C) 2002 - 2011 Paul Mundt
5 * Copyright (C) 2015 Glider bvba
6 * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
7 *
8 * based off of the old drivers/char/sh-sci.c by:
9 *
10 * Copyright (C) 1999, 2000 Niibe Yutaka
11 * Copyright (C) 2000 Sugioka Toshinobu
12 * Modified to support multiple serial ports. Stuart Menefy (May 2000).
13 * Modified to support SecureEdge. David McCullough (2002)
14 * Modified to support SH7300 SCIF. Takashi Kusuda (Jun 2003).
15 * Removed SH7300 support (Jul 2007).
16 *
17 * This file is subject to the terms and conditions of the GNU General Public
18 * License. See the file "COPYING" in the main directory of this archive
19 * for more details.
20 */
21#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
22#define SUPPORT_SYSRQ
23#endif
24
25#undef DEBUG
26
27#include <linux/clk.h>
28#include <linux/console.h>
29#include <linux/ctype.h>
30#include <linux/cpufreq.h>
31#include <linux/delay.h>
32#include <linux/dmaengine.h>
33#include <linux/dma-mapping.h>
34#include <linux/err.h>
35#include <linux/errno.h>
36#include <linux/init.h>
37#include <linux/interrupt.h>
38#include <linux/ioport.h>
39#include <linux/major.h>
40#include <linux/module.h>
41#include <linux/mm.h>
42#include <linux/of.h>
43#include <linux/platform_device.h>
44#include <linux/pm_runtime.h>
45#include <linux/scatterlist.h>
46#include <linux/serial.h>
47#include <linux/serial_sci.h>
48#include <linux/sh_dma.h>
49#include <linux/slab.h>
50#include <linux/string.h>
51#include <linux/sysrq.h>
52#include <linux/timer.h>
53#include <linux/tty.h>
54#include <linux/tty_flip.h>
55
56#ifdef CONFIG_SUPERH
57#include <asm/sh_bios.h>
58#endif
59
60#include "serial_mctrl_gpio.h"
61#include "sh-sci.h"
62
63/* Offsets into the sci_port->irqs array */
64enum {
65 SCIx_ERI_IRQ,
66 SCIx_RXI_IRQ,
67 SCIx_TXI_IRQ,
68 SCIx_BRI_IRQ,
69 SCIx_NR_IRQS,
70
71 SCIx_MUX_IRQ = SCIx_NR_IRQS, /* special case */
72};
73
74#define SCIx_IRQ_IS_MUXED(port) \
75 ((port)->irqs[SCIx_ERI_IRQ] == \
76 (port)->irqs[SCIx_RXI_IRQ]) || \
77 ((port)->irqs[SCIx_ERI_IRQ] && \
78 ((port)->irqs[SCIx_RXI_IRQ] < 0))
79
80enum SCI_CLKS {
81 SCI_FCK, /* Functional Clock */
82 SCI_SCK, /* Optional External Clock */
83 SCI_BRG_INT, /* Optional BRG Internal Clock Source */
84 SCI_SCIF_CLK, /* Optional BRG External Clock Source */
85 SCI_NUM_CLKS
86};
87
88/* Bit x set means sampling rate x + 1 is supported */
89#define SCI_SR(x) BIT((x) - 1)
90#define SCI_SR_RANGE(x, y) GENMASK((y) - 1, (x) - 1)
91
92#define SCI_SR_SCIFAB SCI_SR(5) | SCI_SR(7) | SCI_SR(11) | \
93 SCI_SR(13) | SCI_SR(16) | SCI_SR(17) | \
94 SCI_SR(19) | SCI_SR(27)
95
96#define min_sr(_port) ffs((_port)->sampling_rate_mask)
97#define max_sr(_port) fls((_port)->sampling_rate_mask)
98
99/* Iterate over all supported sampling rates, from high to low */
100#define for_each_sr(_sr, _port) \
101 for ((_sr) = max_sr(_port); (_sr) >= min_sr(_port); (_sr)--) \
102 if ((_port)->sampling_rate_mask & SCI_SR((_sr)))
103
104struct sci_port {
105 struct uart_port port;
106
107 /* Platform configuration */
108 struct plat_sci_port *cfg;
109 unsigned int overrun_reg;
110 unsigned int overrun_mask;
111 unsigned int error_mask;
112 unsigned int error_clear;
113 unsigned int sampling_rate_mask;
114 resource_size_t reg_size;
115 struct mctrl_gpios *gpios;
116
117 /* Break timer */
118 struct timer_list break_timer;
119 int break_flag;
120
121 /* Clocks */
122 struct clk *clks[SCI_NUM_CLKS];
123 unsigned long clk_rates[SCI_NUM_CLKS];
124
125 int irqs[SCIx_NR_IRQS];
126 char *irqstr[SCIx_NR_IRQS];
127
128 struct dma_chan *chan_tx;
129 struct dma_chan *chan_rx;
130
131#ifdef CONFIG_SERIAL_SH_SCI_DMA
132 dma_cookie_t cookie_tx;
133 dma_cookie_t cookie_rx[2];
134 dma_cookie_t active_rx;
135 dma_addr_t tx_dma_addr;
136 unsigned int tx_dma_len;
137 struct scatterlist sg_rx[2];
138 void *rx_buf[2];
139 size_t buf_len_rx;
140 struct work_struct work_tx;
141 struct timer_list rx_timer;
142 unsigned int rx_timeout;
143#endif
144
145 bool autorts;
146};
147
148#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS
149
150static struct sci_port sci_ports[SCI_NPORTS];
151static struct uart_driver sci_uart_driver;
152
153static inline struct sci_port *
154to_sci_port(struct uart_port *uart)
155{
156 return container_of(uart, struct sci_port, port);
157}
158
159struct plat_sci_reg {
160 u8 offset, size;
161};
162
163/* Helper for invalidating specific entries of an inherited map. */
164#define sci_reg_invalid { .offset = 0, .size = 0 }
165
166static const struct plat_sci_reg sci_regmap[SCIx_NR_REGTYPES][SCIx_NR_REGS] = {
167 [SCIx_PROBE_REGTYPE] = {
168 [0 ... SCIx_NR_REGS - 1] = sci_reg_invalid,
169 },
170
171 /*
172 * Common SCI definitions, dependent on the port's regshift
173 * value.
174 */
175 [SCIx_SCI_REGTYPE] = {
176 [SCSMR] = { 0x00, 8 },
177 [SCBRR] = { 0x01, 8 },
178 [SCSCR] = { 0x02, 8 },
179 [SCxTDR] = { 0x03, 8 },
180 [SCxSR] = { 0x04, 8 },
181 [SCxRDR] = { 0x05, 8 },
182 [SCFCR] = sci_reg_invalid,
183 [SCFDR] = sci_reg_invalid,
184 [SCTFDR] = sci_reg_invalid,
185 [SCRFDR] = sci_reg_invalid,
186 [SCSPTR] = sci_reg_invalid,
187 [SCLSR] = sci_reg_invalid,
188 [HSSRR] = sci_reg_invalid,
189 [SCPCR] = sci_reg_invalid,
190 [SCPDR] = sci_reg_invalid,
191 [SCDL] = sci_reg_invalid,
192 [SCCKS] = sci_reg_invalid,
193 },
194
195 /*
196 * Common definitions for legacy IrDA ports, dependent on
197 * regshift value.
198 */
199 [SCIx_IRDA_REGTYPE] = {
200 [SCSMR] = { 0x00, 8 },
201 [SCBRR] = { 0x01, 8 },
202 [SCSCR] = { 0x02, 8 },
203 [SCxTDR] = { 0x03, 8 },
204 [SCxSR] = { 0x04, 8 },
205 [SCxRDR] = { 0x05, 8 },
206 [SCFCR] = { 0x06, 8 },
207 [SCFDR] = { 0x07, 16 },
208 [SCTFDR] = sci_reg_invalid,
209 [SCRFDR] = sci_reg_invalid,
210 [SCSPTR] = sci_reg_invalid,
211 [SCLSR] = sci_reg_invalid,
212 [HSSRR] = sci_reg_invalid,
213 [SCPCR] = sci_reg_invalid,
214 [SCPDR] = sci_reg_invalid,
215 [SCDL] = sci_reg_invalid,
216 [SCCKS] = sci_reg_invalid,
217 },
218
219 /*
220 * Common SCIFA definitions.
221 */
222 [SCIx_SCIFA_REGTYPE] = {
223 [SCSMR] = { 0x00, 16 },
224 [SCBRR] = { 0x04, 8 },
225 [SCSCR] = { 0x08, 16 },
226 [SCxTDR] = { 0x20, 8 },
227 [SCxSR] = { 0x14, 16 },
228 [SCxRDR] = { 0x24, 8 },
229 [SCFCR] = { 0x18, 16 },
230 [SCFDR] = { 0x1c, 16 },
231 [SCTFDR] = sci_reg_invalid,
232 [SCRFDR] = sci_reg_invalid,
233 [SCSPTR] = sci_reg_invalid,
234 [SCLSR] = sci_reg_invalid,
235 [HSSRR] = sci_reg_invalid,
236 [SCPCR] = { 0x30, 16 },
237 [SCPDR] = { 0x34, 16 },
238 [SCDL] = sci_reg_invalid,
239 [SCCKS] = sci_reg_invalid,
240 },
241
242 /*
243 * Common SCIFB definitions.
244 */
245 [SCIx_SCIFB_REGTYPE] = {
246 [SCSMR] = { 0x00, 16 },
247 [SCBRR] = { 0x04, 8 },
248 [SCSCR] = { 0x08, 16 },
249 [SCxTDR] = { 0x40, 8 },
250 [SCxSR] = { 0x14, 16 },
251 [SCxRDR] = { 0x60, 8 },
252 [SCFCR] = { 0x18, 16 },
253 [SCFDR] = sci_reg_invalid,
254 [SCTFDR] = { 0x38, 16 },
255 [SCRFDR] = { 0x3c, 16 },
256 [SCSPTR] = sci_reg_invalid,
257 [SCLSR] = sci_reg_invalid,
258 [HSSRR] = sci_reg_invalid,
259 [SCPCR] = { 0x30, 16 },
260 [SCPDR] = { 0x34, 16 },
261 [SCDL] = sci_reg_invalid,
262 [SCCKS] = sci_reg_invalid,
263 },
264
265 /*
266 * Common SH-2(A) SCIF definitions for ports with FIFO data
267 * count registers.
268 */
269 [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
270 [SCSMR] = { 0x00, 16 },
271 [SCBRR] = { 0x04, 8 },
272 [SCSCR] = { 0x08, 16 },
273 [SCxTDR] = { 0x0c, 8 },
274 [SCxSR] = { 0x10, 16 },
275 [SCxRDR] = { 0x14, 8 },
276 [SCFCR] = { 0x18, 16 },
277 [SCFDR] = { 0x1c, 16 },
278 [SCTFDR] = sci_reg_invalid,
279 [SCRFDR] = sci_reg_invalid,
280 [SCSPTR] = { 0x20, 16 },
281 [SCLSR] = { 0x24, 16 },
282 [HSSRR] = sci_reg_invalid,
283 [SCPCR] = sci_reg_invalid,
284 [SCPDR] = sci_reg_invalid,
285 [SCDL] = sci_reg_invalid,
286 [SCCKS] = sci_reg_invalid,
287 },
288
289 /*
290 * Common SH-3 SCIF definitions.
291 */
292 [SCIx_SH3_SCIF_REGTYPE] = {
293 [SCSMR] = { 0x00, 8 },
294 [SCBRR] = { 0x02, 8 },
295 [SCSCR] = { 0x04, 8 },
296 [SCxTDR] = { 0x06, 8 },
297 [SCxSR] = { 0x08, 16 },
298 [SCxRDR] = { 0x0a, 8 },
299 [SCFCR] = { 0x0c, 8 },
300 [SCFDR] = { 0x0e, 16 },
301 [SCTFDR] = sci_reg_invalid,
302 [SCRFDR] = sci_reg_invalid,
303 [SCSPTR] = sci_reg_invalid,
304 [SCLSR] = sci_reg_invalid,
305 [HSSRR] = sci_reg_invalid,
306 [SCPCR] = sci_reg_invalid,
307 [SCPDR] = sci_reg_invalid,
308 [SCDL] = sci_reg_invalid,
309 [SCCKS] = sci_reg_invalid,
310 },
311
312 /*
313 * Common SH-4(A) SCIF(B) definitions.
314 */
315 [SCIx_SH4_SCIF_REGTYPE] = {
316 [SCSMR] = { 0x00, 16 },
317 [SCBRR] = { 0x04, 8 },
318 [SCSCR] = { 0x08, 16 },
319 [SCxTDR] = { 0x0c, 8 },
320 [SCxSR] = { 0x10, 16 },
321 [SCxRDR] = { 0x14, 8 },
322 [SCFCR] = { 0x18, 16 },
323 [SCFDR] = { 0x1c, 16 },
324 [SCTFDR] = sci_reg_invalid,
325 [SCRFDR] = sci_reg_invalid,
326 [SCSPTR] = { 0x20, 16 },
327 [SCLSR] = { 0x24, 16 },
328 [HSSRR] = sci_reg_invalid,
329 [SCPCR] = sci_reg_invalid,
330 [SCPDR] = sci_reg_invalid,
331 [SCDL] = sci_reg_invalid,
332 [SCCKS] = sci_reg_invalid,
333 },
334
335 /*
336 * Common SCIF definitions for ports with a Baud Rate Generator for
337 * External Clock (BRG).
338 */
339 [SCIx_SH4_SCIF_BRG_REGTYPE] = {
340 [SCSMR] = { 0x00, 16 },
341 [SCBRR] = { 0x04, 8 },
342 [SCSCR] = { 0x08, 16 },
343 [SCxTDR] = { 0x0c, 8 },
344 [SCxSR] = { 0x10, 16 },
345 [SCxRDR] = { 0x14, 8 },
346 [SCFCR] = { 0x18, 16 },
347 [SCFDR] = { 0x1c, 16 },
348 [SCTFDR] = sci_reg_invalid,
349 [SCRFDR] = sci_reg_invalid,
350 [SCSPTR] = { 0x20, 16 },
351 [SCLSR] = { 0x24, 16 },
352 [HSSRR] = sci_reg_invalid,
353 [SCPCR] = sci_reg_invalid,
354 [SCPDR] = sci_reg_invalid,
355 [SCDL] = { 0x30, 16 },
356 [SCCKS] = { 0x34, 16 },
357 },
358
359 /*
360 * Common HSCIF definitions.
361 */
362 [SCIx_HSCIF_REGTYPE] = {
363 [SCSMR] = { 0x00, 16 },
364 [SCBRR] = { 0x04, 8 },
365 [SCSCR] = { 0x08, 16 },
366 [SCxTDR] = { 0x0c, 8 },
367 [SCxSR] = { 0x10, 16 },
368 [SCxRDR] = { 0x14, 8 },
369 [SCFCR] = { 0x18, 16 },
370 [SCFDR] = { 0x1c, 16 },
371 [SCTFDR] = sci_reg_invalid,
372 [SCRFDR] = sci_reg_invalid,
373 [SCSPTR] = { 0x20, 16 },
374 [SCLSR] = { 0x24, 16 },
375 [HSSRR] = { 0x40, 16 },
376 [SCPCR] = sci_reg_invalid,
377 [SCPDR] = sci_reg_invalid,
378 [SCDL] = { 0x30, 16 },
379 [SCCKS] = { 0x34, 16 },
380 },
381
382 /*
383 * Common SH-4(A) SCIF(B) definitions for ports without an SCSPTR
384 * register.
385 */
386 [SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE] = {
387 [SCSMR] = { 0x00, 16 },
388 [SCBRR] = { 0x04, 8 },
389 [SCSCR] = { 0x08, 16 },
390 [SCxTDR] = { 0x0c, 8 },
391 [SCxSR] = { 0x10, 16 },
392 [SCxRDR] = { 0x14, 8 },
393 [SCFCR] = { 0x18, 16 },
394 [SCFDR] = { 0x1c, 16 },
395 [SCTFDR] = sci_reg_invalid,
396 [SCRFDR] = sci_reg_invalid,
397 [SCSPTR] = sci_reg_invalid,
398 [SCLSR] = { 0x24, 16 },
399 [HSSRR] = sci_reg_invalid,
400 [SCPCR] = sci_reg_invalid,
401 [SCPDR] = sci_reg_invalid,
402 [SCDL] = sci_reg_invalid,
403 [SCCKS] = sci_reg_invalid,
404 },
405
406 /*
407 * Common SH-4(A) SCIF(B) definitions for ports with FIFO data
408 * count registers.
409 */
410 [SCIx_SH4_SCIF_FIFODATA_REGTYPE] = {
411 [SCSMR] = { 0x00, 16 },
412 [SCBRR] = { 0x04, 8 },
413 [SCSCR] = { 0x08, 16 },
414 [SCxTDR] = { 0x0c, 8 },
415 [SCxSR] = { 0x10, 16 },
416 [SCxRDR] = { 0x14, 8 },
417 [SCFCR] = { 0x18, 16 },
418 [SCFDR] = { 0x1c, 16 },
419 [SCTFDR] = { 0x1c, 16 }, /* aliased to SCFDR */
420 [SCRFDR] = { 0x20, 16 },
421 [SCSPTR] = { 0x24, 16 },
422 [SCLSR] = { 0x28, 16 },
423 [HSSRR] = sci_reg_invalid,
424 [SCPCR] = sci_reg_invalid,
425 [SCPDR] = sci_reg_invalid,
426 [SCDL] = sci_reg_invalid,
427 [SCCKS] = sci_reg_invalid,
428 },
429
430 /*
431 * SH7705-style SCIF(B) ports, lacking both SCSPTR and SCLSR
432 * registers.
433 */
434 [SCIx_SH7705_SCIF_REGTYPE] = {
435 [SCSMR] = { 0x00, 16 },
436 [SCBRR] = { 0x04, 8 },
437 [SCSCR] = { 0x08, 16 },
438 [SCxTDR] = { 0x20, 8 },
439 [SCxSR] = { 0x14, 16 },
440 [SCxRDR] = { 0x24, 8 },
441 [SCFCR] = { 0x18, 16 },
442 [SCFDR] = { 0x1c, 16 },
443 [SCTFDR] = sci_reg_invalid,
444 [SCRFDR] = sci_reg_invalid,
445 [SCSPTR] = sci_reg_invalid,
446 [SCLSR] = sci_reg_invalid,
447 [HSSRR] = sci_reg_invalid,
448 [SCPCR] = sci_reg_invalid,
449 [SCPDR] = sci_reg_invalid,
450 [SCDL] = sci_reg_invalid,
451 [SCCKS] = sci_reg_invalid,
452 },
453};
454
455#define sci_getreg(up, offset) (sci_regmap[to_sci_port(up)->cfg->regtype] + offset)
456
457/*
458 * The "offset" here is rather misleading, in that it refers to an enum
459 * value relative to the port mapping rather than the fixed offset
460 * itself, which needs to be manually retrieved from the platform's
461 * register map for the given port.
462 */
463static unsigned int sci_serial_in(struct uart_port *p, int offset)
464{
465 const struct plat_sci_reg *reg = sci_getreg(p, offset);
466
467 if (reg->size == 8)
468 return ioread8(p->membase + (reg->offset << p->regshift));
469 else if (reg->size == 16)
470 return ioread16(p->membase + (reg->offset << p->regshift));
471 else
472 WARN(1, "Invalid register access\n");
473
474 return 0;
475}
476
477static void sci_serial_out(struct uart_port *p, int offset, int value)
478{
479 const struct plat_sci_reg *reg = sci_getreg(p, offset);
480
481 if (reg->size == 8)
482 iowrite8(value, p->membase + (reg->offset << p->regshift));
483 else if (reg->size == 16)
484 iowrite16(value, p->membase + (reg->offset << p->regshift));
485 else
486 WARN(1, "Invalid register access\n");
487}
488
489static int sci_probe_regmap(struct plat_sci_port *cfg)
490{
491 switch (cfg->type) {
492 case PORT_SCI:
493 cfg->regtype = SCIx_SCI_REGTYPE;
494 break;
495 case PORT_IRDA:
496 cfg->regtype = SCIx_IRDA_REGTYPE;
497 break;
498 case PORT_SCIFA:
499 cfg->regtype = SCIx_SCIFA_REGTYPE;
500 break;
501 case PORT_SCIFB:
502 cfg->regtype = SCIx_SCIFB_REGTYPE;
503 break;
504 case PORT_SCIF:
505 /*
506 * The SH-4 is a bit of a misnomer here, although that's
507 * where this particular port layout originated. This
508 * configuration (or some slight variation thereof)
509 * remains the dominant model for all SCIFs.
510 */
511 cfg->regtype = SCIx_SH4_SCIF_REGTYPE;
512 break;
513 case PORT_HSCIF:
514 cfg->regtype = SCIx_HSCIF_REGTYPE;
515 break;
516 default:
517 pr_err("Can't probe register map for given port\n");
518 return -EINVAL;
519 }
520
521 return 0;
522}
523
524static void sci_port_enable(struct sci_port *sci_port)
525{
526 unsigned int i;
527
528 if (!sci_port->port.dev)
529 return;
530
531 pm_runtime_get_sync(sci_port->port.dev);
532
533 for (i = 0; i < SCI_NUM_CLKS; i++) {
534 clk_prepare_enable(sci_port->clks[i]);
535 sci_port->clk_rates[i] = clk_get_rate(sci_port->clks[i]);
536 }
537 sci_port->port.uartclk = sci_port->clk_rates[SCI_FCK];
538}
539
540static void sci_port_disable(struct sci_port *sci_port)
541{
542 unsigned int i;
543
544 if (!sci_port->port.dev)
545 return;
546
547 /* Cancel the break timer to ensure that the timer handler will not try
548 * to access the hardware with clocks and power disabled. Reset the
549 * break flag to make the break debouncing state machine ready for the
550 * next break.
551 */
552 del_timer_sync(&sci_port->break_timer);
553 sci_port->break_flag = 0;
554
555 for (i = SCI_NUM_CLKS; i-- > 0; )
556 clk_disable_unprepare(sci_port->clks[i]);
557
558 pm_runtime_put_sync(sci_port->port.dev);
559}
560
561static inline unsigned long port_rx_irq_mask(struct uart_port *port)
562{
563 /*
564 * Not all ports (such as SCIFA) will support REIE. Rather than
565 * special-casing the port type, we check the port initialization
566 * IRQ enable mask to see whether the IRQ is desired at all. If
567 * it's unset, it's logically inferred that there's no point in
568 * testing for it.
569 */
570 return SCSCR_RIE | (to_sci_port(port)->cfg->scscr & SCSCR_REIE);
571}
572
573static void sci_start_tx(struct uart_port *port)
574{
575 struct sci_port *s = to_sci_port(port);
576 unsigned short ctrl;
577
578#ifdef CONFIG_SERIAL_SH_SCI_DMA
579 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
580 u16 new, scr = serial_port_in(port, SCSCR);
581 if (s->chan_tx)
582 new = scr | SCSCR_TDRQE;
583 else
584 new = scr & ~SCSCR_TDRQE;
585 if (new != scr)
586 serial_port_out(port, SCSCR, new);
587 }
588
589 if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) &&
590 dma_submit_error(s->cookie_tx)) {
591 s->cookie_tx = 0;
592 schedule_work(&s->work_tx);
593 }
594#endif
595
596 if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
597 /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
598 ctrl = serial_port_in(port, SCSCR);
599 serial_port_out(port, SCSCR, ctrl | SCSCR_TIE);
600 }
601}
602
603static void sci_stop_tx(struct uart_port *port)
604{
605 unsigned short ctrl;
606
607 /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
608 ctrl = serial_port_in(port, SCSCR);
609
610 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
611 ctrl &= ~SCSCR_TDRQE;
612
613 ctrl &= ~SCSCR_TIE;
614
615 serial_port_out(port, SCSCR, ctrl);
616}
617
618static void sci_start_rx(struct uart_port *port)
619{
620 unsigned short ctrl;
621
622 ctrl = serial_port_in(port, SCSCR) | port_rx_irq_mask(port);
623
624 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
625 ctrl &= ~SCSCR_RDRQE;
626
627 serial_port_out(port, SCSCR, ctrl);
628}
629
630static void sci_stop_rx(struct uart_port *port)
631{
632 unsigned short ctrl;
633
634 ctrl = serial_port_in(port, SCSCR);
635
636 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
637 ctrl &= ~SCSCR_RDRQE;
638
639 ctrl &= ~port_rx_irq_mask(port);
640
641 serial_port_out(port, SCSCR, ctrl);
642}
643
644static void sci_clear_SCxSR(struct uart_port *port, unsigned int mask)
645{
646 if (port->type == PORT_SCI) {
647 /* Just store the mask */
648 serial_port_out(port, SCxSR, mask);
649 } else if (to_sci_port(port)->overrun_mask == SCIFA_ORER) {
650 /* SCIFA/SCIFB and SCIF on SH7705/SH7720/SH7721 */
651 /* Only clear the status bits we want to clear */
652 serial_port_out(port, SCxSR,
653 serial_port_in(port, SCxSR) & mask);
654 } else {
655 /* Store the mask, clear parity/framing errors */
656 serial_port_out(port, SCxSR, mask & ~(SCIF_FERC | SCIF_PERC));
657 }
658}
659
660#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \
661 defined(CONFIG_SERIAL_SH_SCI_EARLYCON)
662
663#ifdef CONFIG_CONSOLE_POLL
664static int sci_poll_get_char(struct uart_port *port)
665{
666 unsigned short status;
667 int c;
668
669 do {
670 status = serial_port_in(port, SCxSR);
671 if (status & SCxSR_ERRORS(port)) {
672 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port));
673 continue;
674 }
675 break;
676 } while (1);
677
678 if (!(status & SCxSR_RDxF(port)))
679 return NO_POLL_CHAR;
680
681 c = serial_port_in(port, SCxRDR);
682
683 /* Dummy read */
684 serial_port_in(port, SCxSR);
685 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
686
687 return c;
688}
689#endif
690
691static void sci_poll_put_char(struct uart_port *port, unsigned char c)
692{
693 unsigned short status;
694
695 do {
696 status = serial_port_in(port, SCxSR);
697 } while (!(status & SCxSR_TDxE(port)));
698
699 serial_port_out(port, SCxTDR, c);
700 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
701}
702#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE ||
703 CONFIG_SERIAL_SH_SCI_EARLYCON */
704
705static void sci_init_pins(struct uart_port *port, unsigned int cflag)
706{
707 struct sci_port *s = to_sci_port(port);
708
709 /*
710 * Use port-specific handler if provided.
711 */
712 if (s->cfg->ops && s->cfg->ops->init_pins) {
713 s->cfg->ops->init_pins(port, cflag);
714 return;
715 }
716
717 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
718 u16 ctrl = serial_port_in(port, SCPCR);
719
720 /* Enable RXD and TXD pin functions */
721 ctrl &= ~(SCPCR_RXDC | SCPCR_TXDC);
722 if (to_sci_port(port)->cfg->capabilities & SCIx_HAVE_RTSCTS) {
723 /* RTS# is output, driven 1 */
724 ctrl |= SCPCR_RTSC;
725 serial_port_out(port, SCPDR,
726 serial_port_in(port, SCPDR) | SCPDR_RTSD);
727 /* Enable CTS# pin function */
728 ctrl &= ~SCPCR_CTSC;
729 }
730 serial_port_out(port, SCPCR, ctrl);
731 } else if (sci_getreg(port, SCSPTR)->size) {
732 u16 status = serial_port_in(port, SCSPTR);
733
734 /* RTS# is output, driven 1 */
735 status |= SCSPTR_RTSIO | SCSPTR_RTSDT;
736 /* CTS# and SCK are inputs */
737 status &= ~(SCSPTR_CTSIO | SCSPTR_SCKIO);
738 serial_port_out(port, SCSPTR, status);
739 }
740}
741
742static int sci_txfill(struct uart_port *port)
743{
744 const struct plat_sci_reg *reg;
745
746 reg = sci_getreg(port, SCTFDR);
747 if (reg->size)
748 return serial_port_in(port, SCTFDR) & ((port->fifosize << 1) - 1);
749
750 reg = sci_getreg(port, SCFDR);
751 if (reg->size)
752 return serial_port_in(port, SCFDR) >> 8;
753
754 return !(serial_port_in(port, SCxSR) & SCI_TDRE);
755}
756
757static int sci_txroom(struct uart_port *port)
758{
759 return port->fifosize - sci_txfill(port);
760}
761
762static int sci_rxfill(struct uart_port *port)
763{
764 const struct plat_sci_reg *reg;
765
766 reg = sci_getreg(port, SCRFDR);
767 if (reg->size)
768 return serial_port_in(port, SCRFDR) & ((port->fifosize << 1) - 1);
769
770 reg = sci_getreg(port, SCFDR);
771 if (reg->size)
772 return serial_port_in(port, SCFDR) & ((port->fifosize << 1) - 1);
773
774 return (serial_port_in(port, SCxSR) & SCxSR_RDxF(port)) != 0;
775}
776
777/*
778 * SCI helper for checking the state of the muxed port/RXD pins.
779 */
780static inline int sci_rxd_in(struct uart_port *port)
781{
782 struct sci_port *s = to_sci_port(port);
783
784 if (s->cfg->port_reg <= 0)
785 return 1;
786
787 /* Cast for ARM damage */
788 return !!__raw_readb((void __iomem *)(uintptr_t)s->cfg->port_reg);
789}
790
791/* ********************************************************************** *
792 * the interrupt related routines *
793 * ********************************************************************** */
794
795static void sci_transmit_chars(struct uart_port *port)
796{
797 struct circ_buf *xmit = &port->state->xmit;
798 unsigned int stopped = uart_tx_stopped(port);
799 unsigned short status;
800 unsigned short ctrl;
801 int count;
802
803 status = serial_port_in(port, SCxSR);
804 if (!(status & SCxSR_TDxE(port))) {
805 ctrl = serial_port_in(port, SCSCR);
806 if (uart_circ_empty(xmit))
807 ctrl &= ~SCSCR_TIE;
808 else
809 ctrl |= SCSCR_TIE;
810 serial_port_out(port, SCSCR, ctrl);
811 return;
812 }
813
814 count = sci_txroom(port);
815
816 do {
817 unsigned char c;
818
819 if (port->x_char) {
820 c = port->x_char;
821 port->x_char = 0;
822 } else if (!uart_circ_empty(xmit) && !stopped) {
823 c = xmit->buf[xmit->tail];
824 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
825 } else {
826 break;
827 }
828
829 serial_port_out(port, SCxTDR, c);
830
831 port->icount.tx++;
832 } while (--count > 0);
833
834 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port));
835
836 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
837 uart_write_wakeup(port);
838 if (uart_circ_empty(xmit)) {
839 sci_stop_tx(port);
840 } else {
841 ctrl = serial_port_in(port, SCSCR);
842
843 if (port->type != PORT_SCI) {
844 serial_port_in(port, SCxSR); /* Dummy read */
845 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port));
846 }
847
848 ctrl |= SCSCR_TIE;
849 serial_port_out(port, SCSCR, ctrl);
850 }
851}
852
853/* On SH3, SCIF may read end-of-break as a space->mark char */
854#define STEPFN(c) ({int __c = (c); (((__c-1)|(__c)) == -1); })
855
856static void sci_receive_chars(struct uart_port *port)
857{
858 struct sci_port *sci_port = to_sci_port(port);
859 struct tty_port *tport = &port->state->port;
860 int i, count, copied = 0;
861 unsigned short status;
862 unsigned char flag;
863
864 status = serial_port_in(port, SCxSR);
865 if (!(status & SCxSR_RDxF(port)))
866 return;
867
868 while (1) {
869 /* Don't copy more bytes than there is room for in the buffer */
870 count = tty_buffer_request_room(tport, sci_rxfill(port));
871
872 /* If for any reason we can't copy more data, we're done! */
873 if (count == 0)
874 break;
875
876 if (port->type == PORT_SCI) {
877 char c = serial_port_in(port, SCxRDR);
878 if (uart_handle_sysrq_char(port, c) ||
879 sci_port->break_flag)
880 count = 0;
881 else
882 tty_insert_flip_char(tport, c, TTY_NORMAL);
883 } else {
884 for (i = 0; i < count; i++) {
885 char c = serial_port_in(port, SCxRDR);
886
887 status = serial_port_in(port, SCxSR);
888#if defined(CONFIG_CPU_SH3)
889 /* Skip "chars" during break */
890 if (sci_port->break_flag) {
891 if ((c == 0) &&
892 (status & SCxSR_FER(port))) {
893 count--; i--;
894 continue;
895 }
896
897 /* Nonzero => end-of-break */
898 dev_dbg(port->dev, "debounce<%02x>\n", c);
899 sci_port->break_flag = 0;
900
901 if (STEPFN(c)) {
902 count--; i--;
903 continue;
904 }
905 }
906#endif /* CONFIG_CPU_SH3 */
907 if (uart_handle_sysrq_char(port, c)) {
908 count--; i--;
909 continue;
910 }
911
912 /* Store data and status */
913 if (status & SCxSR_FER(port)) {
914 flag = TTY_FRAME;
915 port->icount.frame++;
916 dev_notice(port->dev, "frame error\n");
917 } else if (status & SCxSR_PER(port)) {
918 flag = TTY_PARITY;
919 port->icount.parity++;
920 dev_notice(port->dev, "parity error\n");
921 } else
922 flag = TTY_NORMAL;
923
924 tty_insert_flip_char(tport, c, flag);
925 }
926 }
927
928 serial_port_in(port, SCxSR); /* dummy read */
929 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
930
931 copied += count;
932 port->icount.rx += count;
933 }
934
935 if (copied) {
936 /* Tell the rest of the system the news. New characters! */
937 tty_flip_buffer_push(tport);
938 } else {
939 serial_port_in(port, SCxSR); /* dummy read */
940 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
941 }
942}
943
944#define SCI_BREAK_JIFFIES (HZ/20)
945
946/*
947 * The sci generates interrupts during the break,
948 * 1 per millisecond or so during the break period, for 9600 baud.
949 * So dont bother disabling interrupts.
950 * But dont want more than 1 break event.
951 * Use a kernel timer to periodically poll the rx line until
952 * the break is finished.
953 */
954static inline void sci_schedule_break_timer(struct sci_port *port)
955{
956 mod_timer(&port->break_timer, jiffies + SCI_BREAK_JIFFIES);
957}
958
959/* Ensure that two consecutive samples find the break over. */
960static void sci_break_timer(unsigned long data)
961{
962 struct sci_port *port = (struct sci_port *)data;
963
964 if (sci_rxd_in(&port->port) == 0) {
965 port->break_flag = 1;
966 sci_schedule_break_timer(port);
967 } else if (port->break_flag == 1) {
968 /* break is over. */
969 port->break_flag = 2;
970 sci_schedule_break_timer(port);
971 } else
972 port->break_flag = 0;
973}
974
975static int sci_handle_errors(struct uart_port *port)
976{
977 int copied = 0;
978 unsigned short status = serial_port_in(port, SCxSR);
979 struct tty_port *tport = &port->state->port;
980 struct sci_port *s = to_sci_port(port);
981
982 /* Handle overruns */
983 if (status & s->overrun_mask) {
984 port->icount.overrun++;
985
986 /* overrun error */
987 if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
988 copied++;
989
990 dev_notice(port->dev, "overrun error\n");
991 }
992
993 if (status & SCxSR_FER(port)) {
994 if (sci_rxd_in(port) == 0) {
995 /* Notify of BREAK */
996 struct sci_port *sci_port = to_sci_port(port);
997
998 if (!sci_port->break_flag) {
999 port->icount.brk++;
1000
1001 sci_port->break_flag = 1;
1002 sci_schedule_break_timer(sci_port);
1003
1004 /* Do sysrq handling. */
1005 if (uart_handle_break(port))
1006 return 0;
1007
1008 dev_dbg(port->dev, "BREAK detected\n");
1009
1010 if (tty_insert_flip_char(tport, 0, TTY_BREAK))
1011 copied++;
1012 }
1013
1014 } else {
1015 /* frame error */
1016 port->icount.frame++;
1017
1018 if (tty_insert_flip_char(tport, 0, TTY_FRAME))
1019 copied++;
1020
1021 dev_notice(port->dev, "frame error\n");
1022 }
1023 }
1024
1025 if (status & SCxSR_PER(port)) {
1026 /* parity error */
1027 port->icount.parity++;
1028
1029 if (tty_insert_flip_char(tport, 0, TTY_PARITY))
1030 copied++;
1031
1032 dev_notice(port->dev, "parity error\n");
1033 }
1034
1035 if (copied)
1036 tty_flip_buffer_push(tport);
1037
1038 return copied;
1039}
1040
1041static int sci_handle_fifo_overrun(struct uart_port *port)
1042{
1043 struct tty_port *tport = &port->state->port;
1044 struct sci_port *s = to_sci_port(port);
1045 const struct plat_sci_reg *reg;
1046 int copied = 0;
1047 u16 status;
1048
1049 reg = sci_getreg(port, s->overrun_reg);
1050 if (!reg->size)
1051 return 0;
1052
1053 status = serial_port_in(port, s->overrun_reg);
1054 if (status & s->overrun_mask) {
1055 status &= ~s->overrun_mask;
1056 serial_port_out(port, s->overrun_reg, status);
1057
1058 port->icount.overrun++;
1059
1060 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
1061 tty_flip_buffer_push(tport);
1062
1063 dev_dbg(port->dev, "overrun error\n");
1064 copied++;
1065 }
1066
1067 return copied;
1068}
1069
1070static int sci_handle_breaks(struct uart_port *port)
1071{
1072 int copied = 0;
1073 unsigned short status = serial_port_in(port, SCxSR);
1074 struct tty_port *tport = &port->state->port;
1075 struct sci_port *s = to_sci_port(port);
1076
1077 if (uart_handle_break(port))
1078 return 0;
1079
1080 if (!s->break_flag && status & SCxSR_BRK(port)) {
1081#if defined(CONFIG_CPU_SH3)
1082 /* Debounce break */
1083 s->break_flag = 1;
1084#endif
1085
1086 port->icount.brk++;
1087
1088 /* Notify of BREAK */
1089 if (tty_insert_flip_char(tport, 0, TTY_BREAK))
1090 copied++;
1091
1092 dev_dbg(port->dev, "BREAK detected\n");
1093 }
1094
1095 if (copied)
1096 tty_flip_buffer_push(tport);
1097
1098 copied += sci_handle_fifo_overrun(port);
1099
1100 return copied;
1101}
1102
1103#ifdef CONFIG_SERIAL_SH_SCI_DMA
1104static void sci_dma_tx_complete(void *arg)
1105{
1106 struct sci_port *s = arg;
1107 struct uart_port *port = &s->port;
1108 struct circ_buf *xmit = &port->state->xmit;
1109 unsigned long flags;
1110
1111 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1112
1113 spin_lock_irqsave(&port->lock, flags);
1114
1115 xmit->tail += s->tx_dma_len;
1116 xmit->tail &= UART_XMIT_SIZE - 1;
1117
1118 port->icount.tx += s->tx_dma_len;
1119
1120 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1121 uart_write_wakeup(port);
1122
1123 if (!uart_circ_empty(xmit)) {
1124 s->cookie_tx = 0;
1125 schedule_work(&s->work_tx);
1126 } else {
1127 s->cookie_tx = -EINVAL;
1128 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1129 u16 ctrl = serial_port_in(port, SCSCR);
1130 serial_port_out(port, SCSCR, ctrl & ~SCSCR_TIE);
1131 }
1132 }
1133
1134 spin_unlock_irqrestore(&port->lock, flags);
1135}
1136
1137/* Locking: called with port lock held */
1138static int sci_dma_rx_push(struct sci_port *s, void *buf, size_t count)
1139{
1140 struct uart_port *port = &s->port;
1141 struct tty_port *tport = &port->state->port;
1142 int copied;
1143
1144 copied = tty_insert_flip_string(tport, buf, count);
1145 if (copied < count)
1146 port->icount.buf_overrun++;
1147
1148 port->icount.rx += copied;
1149
1150 return copied;
1151}
1152
1153static int sci_dma_rx_find_active(struct sci_port *s)
1154{
1155 unsigned int i;
1156
1157 for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++)
1158 if (s->active_rx == s->cookie_rx[i])
1159 return i;
1160
1161 return -1;
1162}
1163
1164static void sci_rx_dma_release(struct sci_port *s, bool enable_pio)
1165{
1166 struct dma_chan *chan = s->chan_rx;
1167 struct uart_port *port = &s->port;
1168 unsigned long flags;
1169
1170 spin_lock_irqsave(&port->lock, flags);
1171 s->chan_rx = NULL;
1172 s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL;
1173 spin_unlock_irqrestore(&port->lock, flags);
1174 dmaengine_terminate_all(chan);
1175 dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0],
1176 sg_dma_address(&s->sg_rx[0]));
1177 dma_release_channel(chan);
1178 if (enable_pio)
1179 sci_start_rx(port);
1180}
1181
1182static void sci_dma_rx_complete(void *arg)
1183{
1184 struct sci_port *s = arg;
1185 struct dma_chan *chan = s->chan_rx;
1186 struct uart_port *port = &s->port;
1187 struct dma_async_tx_descriptor *desc;
1188 unsigned long flags;
1189 int active, count = 0;
1190
1191 dev_dbg(port->dev, "%s(%d) active cookie %d\n", __func__, port->line,
1192 s->active_rx);
1193
1194 spin_lock_irqsave(&port->lock, flags);
1195
1196 active = sci_dma_rx_find_active(s);
1197 if (active >= 0)
1198 count = sci_dma_rx_push(s, s->rx_buf[active], s->buf_len_rx);
1199
1200 mod_timer(&s->rx_timer, jiffies + s->rx_timeout);
1201
1202 if (count)
1203 tty_flip_buffer_push(&port->state->port);
1204
1205 desc = dmaengine_prep_slave_sg(s->chan_rx, &s->sg_rx[active], 1,
1206 DMA_DEV_TO_MEM,
1207 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1208 if (!desc)
1209 goto fail;
1210
1211 desc->callback = sci_dma_rx_complete;
1212 desc->callback_param = s;
1213 s->cookie_rx[active] = dmaengine_submit(desc);
1214 if (dma_submit_error(s->cookie_rx[active]))
1215 goto fail;
1216
1217 s->active_rx = s->cookie_rx[!active];
1218
1219 dma_async_issue_pending(chan);
1220
1221 spin_unlock_irqrestore(&port->lock, flags);
1222 dev_dbg(port->dev, "%s: cookie %d #%d, new active cookie %d\n",
1223 __func__, s->cookie_rx[active], active, s->active_rx);
1224 return;
1225
1226fail:
1227 spin_unlock_irqrestore(&port->lock, flags);
1228 dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
1229 sci_rx_dma_release(s, true);
1230}
1231
1232static void sci_tx_dma_release(struct sci_port *s, bool enable_pio)
1233{
1234 struct dma_chan *chan = s->chan_tx;
1235 struct uart_port *port = &s->port;
1236 unsigned long flags;
1237
1238 spin_lock_irqsave(&port->lock, flags);
1239 s->chan_tx = NULL;
1240 s->cookie_tx = -EINVAL;
1241 spin_unlock_irqrestore(&port->lock, flags);
1242 dmaengine_terminate_all(chan);
1243 dma_unmap_single(chan->device->dev, s->tx_dma_addr, UART_XMIT_SIZE,
1244 DMA_TO_DEVICE);
1245 dma_release_channel(chan);
1246 if (enable_pio)
1247 sci_start_tx(port);
1248}
1249
1250static void sci_submit_rx(struct sci_port *s)
1251{
1252 struct dma_chan *chan = s->chan_rx;
1253 int i;
1254
1255 for (i = 0; i < 2; i++) {
1256 struct scatterlist *sg = &s->sg_rx[i];
1257 struct dma_async_tx_descriptor *desc;
1258
1259 desc = dmaengine_prep_slave_sg(chan,
1260 sg, 1, DMA_DEV_TO_MEM,
1261 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1262 if (!desc)
1263 goto fail;
1264
1265 desc->callback = sci_dma_rx_complete;
1266 desc->callback_param = s;
1267 s->cookie_rx[i] = dmaengine_submit(desc);
1268 if (dma_submit_error(s->cookie_rx[i]))
1269 goto fail;
1270
1271 }
1272
1273 s->active_rx = s->cookie_rx[0];
1274
1275 dma_async_issue_pending(chan);
1276 return;
1277
1278fail:
1279 if (i)
1280 dmaengine_terminate_all(chan);
1281 for (i = 0; i < 2; i++)
1282 s->cookie_rx[i] = -EINVAL;
1283 s->active_rx = -EINVAL;
1284 sci_rx_dma_release(s, true);
1285}
1286
1287static void work_fn_tx(struct work_struct *work)
1288{
1289 struct sci_port *s = container_of(work, struct sci_port, work_tx);
1290 struct dma_async_tx_descriptor *desc;
1291 struct dma_chan *chan = s->chan_tx;
1292 struct uart_port *port = &s->port;
1293 struct circ_buf *xmit = &port->state->xmit;
1294 dma_addr_t buf;
1295
1296 /*
1297 * DMA is idle now.
1298 * Port xmit buffer is already mapped, and it is one page... Just adjust
1299 * offsets and lengths. Since it is a circular buffer, we have to
1300 * transmit till the end, and then the rest. Take the port lock to get a
1301 * consistent xmit buffer state.
1302 */
1303 spin_lock_irq(&port->lock);
1304 buf = s->tx_dma_addr + (xmit->tail & (UART_XMIT_SIZE - 1));
1305 s->tx_dma_len = min_t(unsigned int,
1306 CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE),
1307 CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE));
1308 spin_unlock_irq(&port->lock);
1309
1310 desc = dmaengine_prep_slave_single(chan, buf, s->tx_dma_len,
1311 DMA_MEM_TO_DEV,
1312 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1313 if (!desc) {
1314 dev_warn(port->dev, "Failed preparing Tx DMA descriptor\n");
1315 /* switch to PIO */
1316 sci_tx_dma_release(s, true);
1317 return;
1318 }
1319
1320 dma_sync_single_for_device(chan->device->dev, buf, s->tx_dma_len,
1321 DMA_TO_DEVICE);
1322
1323 spin_lock_irq(&port->lock);
1324 desc->callback = sci_dma_tx_complete;
1325 desc->callback_param = s;
1326 spin_unlock_irq(&port->lock);
1327 s->cookie_tx = dmaengine_submit(desc);
1328 if (dma_submit_error(s->cookie_tx)) {
1329 dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n");
1330 /* switch to PIO */
1331 sci_tx_dma_release(s, true);
1332 return;
1333 }
1334
1335 dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n",
1336 __func__, xmit->buf, xmit->tail, xmit->head, s->cookie_tx);
1337
1338 dma_async_issue_pending(chan);
1339}
1340
1341static void rx_timer_fn(unsigned long arg)
1342{
1343 struct sci_port *s = (struct sci_port *)arg;
1344 struct dma_chan *chan = s->chan_rx;
1345 struct uart_port *port = &s->port;
1346 struct dma_tx_state state;
1347 enum dma_status status;
1348 unsigned long flags;
1349 unsigned int read;
1350 int active, count;
1351 u16 scr;
1352
1353 dev_dbg(port->dev, "DMA Rx timed out\n");
1354
1355 spin_lock_irqsave(&port->lock, flags);
1356
1357 active = sci_dma_rx_find_active(s);
1358 if (active < 0) {
1359 spin_unlock_irqrestore(&port->lock, flags);
1360 return;
1361 }
1362
1363 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state);
1364 if (status == DMA_COMPLETE) {
1365 spin_unlock_irqrestore(&port->lock, flags);
1366 dev_dbg(port->dev, "Cookie %d #%d has already completed\n",
1367 s->active_rx, active);
1368
1369 /* Let packet complete handler take care of the packet */
1370 return;
1371 }
1372
1373 dmaengine_pause(chan);
1374
1375 /*
1376 * sometimes DMA transfer doesn't stop even if it is stopped and
1377 * data keeps on coming until transaction is complete so check
1378 * for DMA_COMPLETE again
1379 * Let packet complete handler take care of the packet
1380 */
1381 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state);
1382 if (status == DMA_COMPLETE) {
1383 spin_unlock_irqrestore(&port->lock, flags);
1384 dev_dbg(port->dev, "Transaction complete after DMA engine was stopped");
1385 return;
1386 }
1387
1388 /* Handle incomplete DMA receive */
1389 dmaengine_terminate_all(s->chan_rx);
1390 read = sg_dma_len(&s->sg_rx[active]) - state.residue;
1391
1392 if (read) {
1393 count = sci_dma_rx_push(s, s->rx_buf[active], read);
1394 if (count)
1395 tty_flip_buffer_push(&port->state->port);
1396 }
1397
1398 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1399 sci_submit_rx(s);
1400
1401 /* Direct new serial port interrupts back to CPU */
1402 scr = serial_port_in(port, SCSCR);
1403 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1404 scr &= ~SCSCR_RDRQE;
1405 enable_irq(s->irqs[SCIx_RXI_IRQ]);
1406 }
1407 serial_port_out(port, SCSCR, scr | SCSCR_RIE);
1408
1409 spin_unlock_irqrestore(&port->lock, flags);
1410}
1411
1412static struct dma_chan *sci_request_dma_chan(struct uart_port *port,
1413 enum dma_transfer_direction dir,
1414 unsigned int id)
1415{
1416 dma_cap_mask_t mask;
1417 struct dma_chan *chan;
1418 struct dma_slave_config cfg;
1419 int ret;
1420
1421 dma_cap_zero(mask);
1422 dma_cap_set(DMA_SLAVE, mask);
1423
1424 chan = dma_request_slave_channel_compat(mask, shdma_chan_filter,
1425 (void *)(unsigned long)id, port->dev,
1426 dir == DMA_MEM_TO_DEV ? "tx" : "rx");
1427 if (!chan) {
1428 dev_warn(port->dev,
1429 "dma_request_slave_channel_compat failed\n");
1430 return NULL;
1431 }
1432
1433 memset(&cfg, 0, sizeof(cfg));
1434 cfg.direction = dir;
1435 if (dir == DMA_MEM_TO_DEV) {
1436 cfg.dst_addr = port->mapbase +
1437 (sci_getreg(port, SCxTDR)->offset << port->regshift);
1438 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1439 } else {
1440 cfg.src_addr = port->mapbase +
1441 (sci_getreg(port, SCxRDR)->offset << port->regshift);
1442 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1443 }
1444
1445 ret = dmaengine_slave_config(chan, &cfg);
1446 if (ret) {
1447 dev_warn(port->dev, "dmaengine_slave_config failed %d\n", ret);
1448 dma_release_channel(chan);
1449 return NULL;
1450 }
1451
1452 return chan;
1453}
1454
1455static void sci_request_dma(struct uart_port *port)
1456{
1457 struct sci_port *s = to_sci_port(port);
1458 struct dma_chan *chan;
1459
1460 dev_dbg(port->dev, "%s: port %d\n", __func__, port->line);
1461
1462 if (!port->dev->of_node &&
1463 (s->cfg->dma_slave_tx <= 0 || s->cfg->dma_slave_rx <= 0))
1464 return;
1465
1466 s->cookie_tx = -EINVAL;
1467 chan = sci_request_dma_chan(port, DMA_MEM_TO_DEV, s->cfg->dma_slave_tx);
1468 dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan);
1469 if (chan) {
1470 s->chan_tx = chan;
1471 /* UART circular tx buffer is an aligned page. */
1472 s->tx_dma_addr = dma_map_single(chan->device->dev,
1473 port->state->xmit.buf,
1474 UART_XMIT_SIZE,
1475 DMA_TO_DEVICE);
1476 if (dma_mapping_error(chan->device->dev, s->tx_dma_addr)) {
1477 dev_warn(port->dev, "Failed mapping Tx DMA descriptor\n");
1478 dma_release_channel(chan);
1479 s->chan_tx = NULL;
1480 } else {
1481 dev_dbg(port->dev, "%s: mapped %lu@%p to %pad\n",
1482 __func__, UART_XMIT_SIZE,
1483 port->state->xmit.buf, &s->tx_dma_addr);
1484 }
1485
1486 INIT_WORK(&s->work_tx, work_fn_tx);
1487 }
1488
1489 chan = sci_request_dma_chan(port, DMA_DEV_TO_MEM, s->cfg->dma_slave_rx);
1490 dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan);
1491 if (chan) {
1492 unsigned int i;
1493 dma_addr_t dma;
1494 void *buf;
1495
1496 s->chan_rx = chan;
1497
1498 s->buf_len_rx = 2 * max_t(size_t, 16, port->fifosize);
1499 buf = dma_alloc_coherent(chan->device->dev, s->buf_len_rx * 2,
1500 &dma, GFP_KERNEL);
1501 if (!buf) {
1502 dev_warn(port->dev,
1503 "Failed to allocate Rx dma buffer, using PIO\n");
1504 dma_release_channel(chan);
1505 s->chan_rx = NULL;
1506 return;
1507 }
1508
1509 for (i = 0; i < 2; i++) {
1510 struct scatterlist *sg = &s->sg_rx[i];
1511
1512 sg_init_table(sg, 1);
1513 s->rx_buf[i] = buf;
1514 sg_dma_address(sg) = dma;
1515 sg_dma_len(sg) = s->buf_len_rx;
1516
1517 buf += s->buf_len_rx;
1518 dma += s->buf_len_rx;
1519 }
1520
1521 setup_timer(&s->rx_timer, rx_timer_fn, (unsigned long)s);
1522
1523 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
1524 sci_submit_rx(s);
1525 }
1526}
1527
1528static void sci_free_dma(struct uart_port *port)
1529{
1530 struct sci_port *s = to_sci_port(port);
1531
1532 if (s->chan_tx)
1533 sci_tx_dma_release(s, false);
1534 if (s->chan_rx)
1535 sci_rx_dma_release(s, false);
1536}
1537#else
1538static inline void sci_request_dma(struct uart_port *port)
1539{
1540}
1541
1542static inline void sci_free_dma(struct uart_port *port)
1543{
1544}
1545#endif
1546
1547static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
1548{
1549#ifdef CONFIG_SERIAL_SH_SCI_DMA
1550 struct uart_port *port = ptr;
1551 struct sci_port *s = to_sci_port(port);
1552
1553 if (s->chan_rx) {
1554 u16 scr = serial_port_in(port, SCSCR);
1555 u16 ssr = serial_port_in(port, SCxSR);
1556
1557 /* Disable future Rx interrupts */
1558 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1559 disable_irq_nosync(irq);
1560 scr |= SCSCR_RDRQE;
1561 } else {
1562 scr &= ~SCSCR_RIE;
1563 sci_submit_rx(s);
1564 }
1565 serial_port_out(port, SCSCR, scr);
1566 /* Clear current interrupt */
1567 serial_port_out(port, SCxSR,
1568 ssr & ~(SCIF_DR | SCxSR_RDxF(port)));
1569 dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u jiffies\n",
1570 jiffies, s->rx_timeout);
1571 mod_timer(&s->rx_timer, jiffies + s->rx_timeout);
1572
1573 return IRQ_HANDLED;
1574 }
1575#endif
1576
1577 /* I think sci_receive_chars has to be called irrespective
1578 * of whether the I_IXOFF is set, otherwise, how is the interrupt
1579 * to be disabled?
1580 */
1581 sci_receive_chars(ptr);
1582
1583 return IRQ_HANDLED;
1584}
1585
1586static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
1587{
1588 struct uart_port *port = ptr;
1589 unsigned long flags;
1590
1591 spin_lock_irqsave(&port->lock, flags);
1592 sci_transmit_chars(port);
1593 spin_unlock_irqrestore(&port->lock, flags);
1594
1595 return IRQ_HANDLED;
1596}
1597
1598static irqreturn_t sci_er_interrupt(int irq, void *ptr)
1599{
1600 struct uart_port *port = ptr;
1601 struct sci_port *s = to_sci_port(port);
1602
1603 /* Handle errors */
1604 if (port->type == PORT_SCI) {
1605 if (sci_handle_errors(port)) {
1606 /* discard character in rx buffer */
1607 serial_port_in(port, SCxSR);
1608 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port));
1609 }
1610 } else {
1611 sci_handle_fifo_overrun(port);
1612 if (!s->chan_rx)
1613 sci_receive_chars(ptr);
1614 }
1615
1616 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port));
1617
1618 /* Kick the transmission */
1619 if (!s->chan_tx)
1620 sci_tx_interrupt(irq, ptr);
1621
1622 return IRQ_HANDLED;
1623}
1624
1625static irqreturn_t sci_br_interrupt(int irq, void *ptr)
1626{
1627 struct uart_port *port = ptr;
1628
1629 /* Handle BREAKs */
1630 sci_handle_breaks(port);
1631 sci_clear_SCxSR(port, SCxSR_BREAK_CLEAR(port));
1632
1633 return IRQ_HANDLED;
1634}
1635
1636static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
1637{
1638 unsigned short ssr_status, scr_status, err_enabled, orer_status = 0;
1639 struct uart_port *port = ptr;
1640 struct sci_port *s = to_sci_port(port);
1641 irqreturn_t ret = IRQ_NONE;
1642
1643 ssr_status = serial_port_in(port, SCxSR);
1644 scr_status = serial_port_in(port, SCSCR);
1645 if (s->overrun_reg == SCxSR)
1646 orer_status = ssr_status;
1647 else {
1648 if (sci_getreg(port, s->overrun_reg)->size)
1649 orer_status = serial_port_in(port, s->overrun_reg);
1650 }
1651
1652 err_enabled = scr_status & port_rx_irq_mask(port);
1653
1654 /* Tx Interrupt */
1655 if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) &&
1656 !s->chan_tx)
1657 ret = sci_tx_interrupt(irq, ptr);
1658
1659 /*
1660 * Rx Interrupt: if we're using DMA, the DMA controller clears RDF /
1661 * DR flags
1662 */
1663 if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) &&
1664 (scr_status & SCSCR_RIE))
1665 ret = sci_rx_interrupt(irq, ptr);
1666
1667 /* Error Interrupt */
1668 if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled)
1669 ret = sci_er_interrupt(irq, ptr);
1670
1671 /* Break Interrupt */
1672 if ((ssr_status & SCxSR_BRK(port)) && err_enabled)
1673 ret = sci_br_interrupt(irq, ptr);
1674
1675 /* Overrun Interrupt */
1676 if (orer_status & s->overrun_mask) {
1677 sci_handle_fifo_overrun(port);
1678 ret = IRQ_HANDLED;
1679 }
1680
1681 return ret;
1682}
1683
1684static const struct sci_irq_desc {
1685 const char *desc;
1686 irq_handler_t handler;
1687} sci_irq_desc[] = {
1688 /*
1689 * Split out handlers, the default case.
1690 */
1691 [SCIx_ERI_IRQ] = {
1692 .desc = "rx err",
1693 .handler = sci_er_interrupt,
1694 },
1695
1696 [SCIx_RXI_IRQ] = {
1697 .desc = "rx full",
1698 .handler = sci_rx_interrupt,
1699 },
1700
1701 [SCIx_TXI_IRQ] = {
1702 .desc = "tx empty",
1703 .handler = sci_tx_interrupt,
1704 },
1705
1706 [SCIx_BRI_IRQ] = {
1707 .desc = "break",
1708 .handler = sci_br_interrupt,
1709 },
1710
1711 /*
1712 * Special muxed handler.
1713 */
1714 [SCIx_MUX_IRQ] = {
1715 .desc = "mux",
1716 .handler = sci_mpxed_interrupt,
1717 },
1718};
1719
1720static int sci_request_irq(struct sci_port *port)
1721{
1722 struct uart_port *up = &port->port;
1723 int i, j, ret = 0;
1724
1725 for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
1726 const struct sci_irq_desc *desc;
1727 int irq;
1728
1729 if (SCIx_IRQ_IS_MUXED(port)) {
1730 i = SCIx_MUX_IRQ;
1731 irq = up->irq;
1732 } else {
1733 irq = port->irqs[i];
1734
1735 /*
1736 * Certain port types won't support all of the
1737 * available interrupt sources.
1738 */
1739 if (unlikely(irq < 0))
1740 continue;
1741 }
1742
1743 desc = sci_irq_desc + i;
1744 port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
1745 dev_name(up->dev), desc->desc);
1746 if (!port->irqstr[j])
1747 goto out_nomem;
1748
1749 ret = request_irq(irq, desc->handler, up->irqflags,
1750 port->irqstr[j], port);
1751 if (unlikely(ret)) {
1752 dev_err(up->dev, "Can't allocate %s IRQ\n", desc->desc);
1753 goto out_noirq;
1754 }
1755 }
1756
1757 return 0;
1758
1759out_noirq:
1760 while (--i >= 0)
1761 free_irq(port->irqs[i], port);
1762
1763out_nomem:
1764 while (--j >= 0)
1765 kfree(port->irqstr[j]);
1766
1767 return ret;
1768}
1769
1770static void sci_free_irq(struct sci_port *port)
1771{
1772 int i;
1773
1774 /*
1775 * Intentionally in reverse order so we iterate over the muxed
1776 * IRQ first.
1777 */
1778 for (i = 0; i < SCIx_NR_IRQS; i++) {
1779 int irq = port->irqs[i];
1780
1781 /*
1782 * Certain port types won't support all of the available
1783 * interrupt sources.
1784 */
1785 if (unlikely(irq < 0))
1786 continue;
1787
1788 free_irq(port->irqs[i], port);
1789 kfree(port->irqstr[i]);
1790
1791 if (SCIx_IRQ_IS_MUXED(port)) {
1792 /* If there's only one IRQ, we're done. */
1793 return;
1794 }
1795 }
1796}
1797
1798static unsigned int sci_tx_empty(struct uart_port *port)
1799{
1800 unsigned short status = serial_port_in(port, SCxSR);
1801 unsigned short in_tx_fifo = sci_txfill(port);
1802
1803 return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
1804}
1805
1806static void sci_set_rts(struct uart_port *port, bool state)
1807{
1808 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1809 u16 data = serial_port_in(port, SCPDR);
1810
1811 /* Active low */
1812 if (state)
1813 data &= ~SCPDR_RTSD;
1814 else
1815 data |= SCPDR_RTSD;
1816 serial_port_out(port, SCPDR, data);
1817
1818 /* RTS# is output */
1819 serial_port_out(port, SCPCR,
1820 serial_port_in(port, SCPCR) | SCPCR_RTSC);
1821 } else if (sci_getreg(port, SCSPTR)->size) {
1822 u16 ctrl = serial_port_in(port, SCSPTR);
1823
1824 /* Active low */
1825 if (state)
1826 ctrl &= ~SCSPTR_RTSDT;
1827 else
1828 ctrl |= SCSPTR_RTSDT;
1829 serial_port_out(port, SCSPTR, ctrl);
1830 }
1831}
1832
1833static bool sci_get_cts(struct uart_port *port)
1834{
1835 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1836 /* Active low */
1837 return !(serial_port_in(port, SCPDR) & SCPDR_CTSD);
1838 } else if (sci_getreg(port, SCSPTR)->size) {
1839 /* Active low */
1840 return !(serial_port_in(port, SCSPTR) & SCSPTR_CTSDT);
1841 }
1842
1843 return true;
1844}
1845
1846/*
1847 * Modem control is a bit of a mixed bag for SCI(F) ports. Generally
1848 * CTS/RTS is supported in hardware by at least one port and controlled
1849 * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently
1850 * handled via the ->init_pins() op, which is a bit of a one-way street,
1851 * lacking any ability to defer pin control -- this will later be
1852 * converted over to the GPIO framework).
1853 *
1854 * Other modes (such as loopback) are supported generically on certain
1855 * port types, but not others. For these it's sufficient to test for the
1856 * existence of the support register and simply ignore the port type.
1857 */
1858static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
1859{
1860 struct sci_port *s = to_sci_port(port);
1861
1862 if (mctrl & TIOCM_LOOP) {
1863 const struct plat_sci_reg *reg;
1864
1865 /*
1866 * Standard loopback mode for SCFCR ports.
1867 */
1868 reg = sci_getreg(port, SCFCR);
1869 if (reg->size)
1870 serial_port_out(port, SCFCR,
1871 serial_port_in(port, SCFCR) |
1872 SCFCR_LOOP);
1873 }
1874
1875 mctrl_gpio_set(s->gpios, mctrl);
1876
1877 if (!(s->cfg->capabilities & SCIx_HAVE_RTSCTS))
1878 return;
1879
1880 if (!(mctrl & TIOCM_RTS)) {
1881 /* Disable Auto RTS */
1882 serial_port_out(port, SCFCR,
1883 serial_port_in(port, SCFCR) & ~SCFCR_MCE);
1884
1885 /* Clear RTS */
1886 sci_set_rts(port, 0);
1887 } else if (s->autorts) {
1888 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
1889 /* Enable RTS# pin function */
1890 serial_port_out(port, SCPCR,
1891 serial_port_in(port, SCPCR) & ~SCPCR_RTSC);
1892 }
1893
1894 /* Enable Auto RTS */
1895 serial_port_out(port, SCFCR,
1896 serial_port_in(port, SCFCR) | SCFCR_MCE);
1897 } else {
1898 /* Set RTS */
1899 sci_set_rts(port, 1);
1900 }
1901}
1902
1903static unsigned int sci_get_mctrl(struct uart_port *port)
1904{
1905 struct sci_port *s = to_sci_port(port);
1906 struct mctrl_gpios *gpios = s->gpios;
1907 unsigned int mctrl = 0;
1908
1909 mctrl_gpio_get(gpios, &mctrl);
1910
1911 /*
1912 * CTS/RTS is handled in hardware when supported, while nothing
1913 * else is wired up.
1914 */
1915 if (s->autorts) {
1916 if (sci_get_cts(port))
1917 mctrl |= TIOCM_CTS;
1918 } else if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_CTS))) {
1919 mctrl |= TIOCM_CTS;
1920 }
1921 if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_DSR)))
1922 mctrl |= TIOCM_DSR;
1923 if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_DCD)))
1924 mctrl |= TIOCM_CAR;
1925
1926 return mctrl;
1927}
1928
1929static void sci_enable_ms(struct uart_port *port)
1930{
1931 mctrl_gpio_enable_ms(to_sci_port(port)->gpios);
1932}
1933
1934static void sci_break_ctl(struct uart_port *port, int break_state)
1935{
1936 unsigned short scscr, scsptr;
1937
1938 /* check wheter the port has SCSPTR */
1939 if (!sci_getreg(port, SCSPTR)->size) {
1940 /*
1941 * Not supported by hardware. Most parts couple break and rx
1942 * interrupts together, with break detection always enabled.
1943 */
1944 return;
1945 }
1946
1947 scsptr = serial_port_in(port, SCSPTR);
1948 scscr = serial_port_in(port, SCSCR);
1949
1950 if (break_state == -1) {
1951 scsptr = (scsptr | SCSPTR_SPB2IO) & ~SCSPTR_SPB2DT;
1952 scscr &= ~SCSCR_TE;
1953 } else {
1954 scsptr = (scsptr | SCSPTR_SPB2DT) & ~SCSPTR_SPB2IO;
1955 scscr |= SCSCR_TE;
1956 }
1957
1958 serial_port_out(port, SCSPTR, scsptr);
1959 serial_port_out(port, SCSCR, scscr);
1960}
1961
1962static int sci_startup(struct uart_port *port)
1963{
1964 struct sci_port *s = to_sci_port(port);
1965 int ret;
1966
1967 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1968
1969 ret = sci_request_irq(s);
1970 if (unlikely(ret < 0))
1971 return ret;
1972
1973 sci_request_dma(port);
1974
1975 return 0;
1976}
1977
1978static void sci_shutdown(struct uart_port *port)
1979{
1980 struct sci_port *s = to_sci_port(port);
1981 unsigned long flags;
1982 u16 scr;
1983
1984 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
1985
1986 s->autorts = false;
1987 mctrl_gpio_disable_ms(to_sci_port(port)->gpios);
1988
1989 spin_lock_irqsave(&port->lock, flags);
1990 sci_stop_rx(port);
1991 sci_stop_tx(port);
1992 /* Stop RX and TX, disable related interrupts, keep clock source */
1993 scr = serial_port_in(port, SCSCR);
1994 serial_port_out(port, SCSCR, scr & (SCSCR_CKE1 | SCSCR_CKE0));
1995 spin_unlock_irqrestore(&port->lock, flags);
1996
1997#ifdef CONFIG_SERIAL_SH_SCI_DMA
1998 if (s->chan_rx) {
1999 dev_dbg(port->dev, "%s(%d) deleting rx_timer\n", __func__,
2000 port->line);
2001 del_timer_sync(&s->rx_timer);
2002 }
2003#endif
2004
2005 sci_free_dma(port);
2006 sci_free_irq(s);
2007}
2008
2009static int sci_sck_calc(struct sci_port *s, unsigned int bps,
2010 unsigned int *srr)
2011{
2012 unsigned long freq = s->clk_rates[SCI_SCK];
2013 int err, min_err = INT_MAX;
2014 unsigned int sr;
2015
2016 if (s->port.type != PORT_HSCIF)
2017 freq *= 2;
2018
2019 for_each_sr(sr, s) {
2020 err = DIV_ROUND_CLOSEST(freq, sr) - bps;
2021 if (abs(err) >= abs(min_err))
2022 continue;
2023
2024 min_err = err;
2025 *srr = sr - 1;
2026
2027 if (!err)
2028 break;
2029 }
2030
2031 dev_dbg(s->port.dev, "SCK: %u%+d bps using SR %u\n", bps, min_err,
2032 *srr + 1);
2033 return min_err;
2034}
2035
2036static int sci_brg_calc(struct sci_port *s, unsigned int bps,
2037 unsigned long freq, unsigned int *dlr,
2038 unsigned int *srr)
2039{
2040 int err, min_err = INT_MAX;
2041 unsigned int sr, dl;
2042
2043 if (s->port.type != PORT_HSCIF)
2044 freq *= 2;
2045
2046 for_each_sr(sr, s) {
2047 dl = DIV_ROUND_CLOSEST(freq, sr * bps);
2048 dl = clamp(dl, 1U, 65535U);
2049
2050 err = DIV_ROUND_CLOSEST(freq, sr * dl) - bps;
2051 if (abs(err) >= abs(min_err))
2052 continue;
2053
2054 min_err = err;
2055 *dlr = dl;
2056 *srr = sr - 1;
2057
2058 if (!err)
2059 break;
2060 }
2061
2062 dev_dbg(s->port.dev, "BRG: %u%+d bps using DL %u SR %u\n", bps,
2063 min_err, *dlr, *srr + 1);
2064 return min_err;
2065}
2066
2067/* calculate sample rate, BRR, and clock select */
2068static int sci_scbrr_calc(struct sci_port *s, unsigned int bps,
2069 unsigned int *brr, unsigned int *srr,
2070 unsigned int *cks)
2071{
2072 unsigned long freq = s->clk_rates[SCI_FCK];
2073 unsigned int sr, br, prediv, scrate, c;
2074 int err, min_err = INT_MAX;
2075
2076 if (s->port.type != PORT_HSCIF)
2077 freq *= 2;
2078
2079 /*
2080 * Find the combination of sample rate and clock select with the
2081 * smallest deviation from the desired baud rate.
2082 * Prefer high sample rates to maximise the receive margin.
2083 *
2084 * M: Receive margin (%)
2085 * N: Ratio of bit rate to clock (N = sampling rate)
2086 * D: Clock duty (D = 0 to 1.0)
2087 * L: Frame length (L = 9 to 12)
2088 * F: Absolute value of clock frequency deviation
2089 *
2090 * M = |(0.5 - 1 / 2 * N) - ((L - 0.5) * F) -
2091 * (|D - 0.5| / N * (1 + F))|
2092 * NOTE: Usually, treat D for 0.5, F is 0 by this calculation.
2093 */
2094 for_each_sr(sr, s) {
2095 for (c = 0; c <= 3; c++) {
2096 /* integerized formulas from HSCIF documentation */
2097 prediv = sr * (1 << (2 * c + 1));
2098
2099 /*
2100 * We need to calculate:
2101 *
2102 * br = freq / (prediv * bps) clamped to [1..256]
2103 * err = freq / (br * prediv) - bps
2104 *
2105 * Watch out for overflow when calculating the desired
2106 * sampling clock rate!
2107 */
2108 if (bps > UINT_MAX / prediv)
2109 break;
2110
2111 scrate = prediv * bps;
2112 br = DIV_ROUND_CLOSEST(freq, scrate);
2113 br = clamp(br, 1U, 256U);
2114
2115 err = DIV_ROUND_CLOSEST(freq, br * prediv) - bps;
2116 if (abs(err) >= abs(min_err))
2117 continue;
2118
2119 min_err = err;
2120 *brr = br - 1;
2121 *srr = sr - 1;
2122 *cks = c;
2123
2124 if (!err)
2125 goto found;
2126 }
2127 }
2128
2129found:
2130 dev_dbg(s->port.dev, "BRR: %u%+d bps using N %u SR %u cks %u\n", bps,
2131 min_err, *brr, *srr + 1, *cks);
2132 return min_err;
2133}
2134
2135static void sci_reset(struct uart_port *port)
2136{
2137 const struct plat_sci_reg *reg;
2138 unsigned int status;
2139
2140 do {
2141 status = serial_port_in(port, SCxSR);
2142 } while (!(status & SCxSR_TEND(port)));
2143
2144 serial_port_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
2145
2146 reg = sci_getreg(port, SCFCR);
2147 if (reg->size)
2148 serial_port_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
2149
2150 sci_clear_SCxSR(port,
2151 SCxSR_RDxF_CLEAR(port) & SCxSR_ERROR_CLEAR(port) &
2152 SCxSR_BREAK_CLEAR(port));
2153 if (sci_getreg(port, SCLSR)->size) {
2154 status = serial_port_in(port, SCLSR);
2155 status &= ~(SCLSR_TO | SCLSR_ORER);
2156 serial_port_out(port, SCLSR, status);
2157 }
2158}
2159
2160static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
2161 struct ktermios *old)
2162{
2163 unsigned int baud, smr_val = SCSMR_ASYNC, scr_val = 0, i;
2164 unsigned int brr = 255, cks = 0, srr = 15, dl = 0, sccks = 0;
2165 unsigned int brr1 = 255, cks1 = 0, srr1 = 15, dl1 = 0;
2166 struct sci_port *s = to_sci_port(port);
2167 const struct plat_sci_reg *reg;
2168 int min_err = INT_MAX, err;
2169 unsigned long max_freq = 0;
2170 int best_clk = -1;
2171
2172 if ((termios->c_cflag & CSIZE) == CS7)
2173 smr_val |= SCSMR_CHR;
2174 if (termios->c_cflag & PARENB)
2175 smr_val |= SCSMR_PE;
2176 if (termios->c_cflag & PARODD)
2177 smr_val |= SCSMR_PE | SCSMR_ODD;
2178 if (termios->c_cflag & CSTOPB)
2179 smr_val |= SCSMR_STOP;
2180
2181 /*
2182 * earlyprintk comes here early on with port->uartclk set to zero.
2183 * the clock framework is not up and running at this point so here
2184 * we assume that 115200 is the maximum baud rate. please note that
2185 * the baud rate is not programmed during earlyprintk - it is assumed
2186 * that the previous boot loader has enabled required clocks and
2187 * setup the baud rate generator hardware for us already.
2188 */
2189 if (!port->uartclk) {
2190 baud = uart_get_baud_rate(port, termios, old, 0, 115200);
2191 goto done;
2192 }
2193
2194 for (i = 0; i < SCI_NUM_CLKS; i++)
2195 max_freq = max(max_freq, s->clk_rates[i]);
2196
2197 baud = uart_get_baud_rate(port, termios, old, 0, max_freq / min_sr(s));
2198 if (!baud)
2199 goto done;
2200
2201 /*
2202 * There can be multiple sources for the sampling clock. Find the one
2203 * that gives us the smallest deviation from the desired baud rate.
2204 */
2205
2206 /* Optional Undivided External Clock */
2207 if (s->clk_rates[SCI_SCK] && port->type != PORT_SCIFA &&
2208 port->type != PORT_SCIFB) {
2209 err = sci_sck_calc(s, baud, &srr1);
2210 if (abs(err) < abs(min_err)) {
2211 best_clk = SCI_SCK;
2212 scr_val = SCSCR_CKE1;
2213 sccks = SCCKS_CKS;
2214 min_err = err;
2215 srr = srr1;
2216 if (!err)
2217 goto done;
2218 }
2219 }
2220
2221 /* Optional BRG Frequency Divided External Clock */
2222 if (s->clk_rates[SCI_SCIF_CLK] && sci_getreg(port, SCDL)->size) {
2223 err = sci_brg_calc(s, baud, s->clk_rates[SCI_SCIF_CLK], &dl1,
2224 &srr1);
2225 if (abs(err) < abs(min_err)) {
2226 best_clk = SCI_SCIF_CLK;
2227 scr_val = SCSCR_CKE1;
2228 sccks = 0;
2229 min_err = err;
2230 dl = dl1;
2231 srr = srr1;
2232 if (!err)
2233 goto done;
2234 }
2235 }
2236
2237 /* Optional BRG Frequency Divided Internal Clock */
2238 if (s->clk_rates[SCI_BRG_INT] && sci_getreg(port, SCDL)->size) {
2239 err = sci_brg_calc(s, baud, s->clk_rates[SCI_BRG_INT], &dl1,
2240 &srr1);
2241 if (abs(err) < abs(min_err)) {
2242 best_clk = SCI_BRG_INT;
2243 scr_val = SCSCR_CKE1;
2244 sccks = SCCKS_XIN;
2245 min_err = err;
2246 dl = dl1;
2247 srr = srr1;
2248 if (!min_err)
2249 goto done;
2250 }
2251 }
2252
2253 /* Divided Functional Clock using standard Bit Rate Register */
2254 err = sci_scbrr_calc(s, baud, &brr1, &srr1, &cks1);
2255 if (abs(err) < abs(min_err)) {
2256 best_clk = SCI_FCK;
2257 scr_val = 0;
2258 min_err = err;
2259 brr = brr1;
2260 srr = srr1;
2261 cks = cks1;
2262 }
2263
2264done:
2265 if (best_clk >= 0)
2266 dev_dbg(port->dev, "Using clk %pC for %u%+d bps\n",
2267 s->clks[best_clk], baud, min_err);
2268
2269 sci_port_enable(s);
2270
2271 /*
2272 * Program the optional External Baud Rate Generator (BRG) first.
2273 * It controls the mux to select (H)SCK or frequency divided clock.
2274 */
2275 if (best_clk >= 0 && sci_getreg(port, SCCKS)->size) {
2276 serial_port_out(port, SCDL, dl);
2277 serial_port_out(port, SCCKS, sccks);
2278 }
2279
2280 sci_reset(port);
2281
2282 uart_update_timeout(port, termios->c_cflag, baud);
2283
2284 if (best_clk >= 0) {
2285 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
2286 switch (srr + 1) {
2287 case 5: smr_val |= SCSMR_SRC_5; break;
2288 case 7: smr_val |= SCSMR_SRC_7; break;
2289 case 11: smr_val |= SCSMR_SRC_11; break;
2290 case 13: smr_val |= SCSMR_SRC_13; break;
2291 case 16: smr_val |= SCSMR_SRC_16; break;
2292 case 17: smr_val |= SCSMR_SRC_17; break;
2293 case 19: smr_val |= SCSMR_SRC_19; break;
2294 case 27: smr_val |= SCSMR_SRC_27; break;
2295 }
2296 smr_val |= cks;
2297 dev_dbg(port->dev,
2298 "SCR 0x%x SMR 0x%x BRR %u CKS 0x%x DL %u SRR %u\n",
2299 scr_val, smr_val, brr, sccks, dl, srr);
2300 serial_port_out(port, SCSCR, scr_val);
2301 serial_port_out(port, SCSMR, smr_val);
2302 serial_port_out(port, SCBRR, brr);
2303 if (sci_getreg(port, HSSRR)->size)
2304 serial_port_out(port, HSSRR, srr | HSCIF_SRE);
2305
2306 /* Wait one bit interval */
2307 udelay((1000000 + (baud - 1)) / baud);
2308 } else {
2309 /* Don't touch the bit rate configuration */
2310 scr_val = s->cfg->scscr & (SCSCR_CKE1 | SCSCR_CKE0);
2311 smr_val |= serial_port_in(port, SCSMR) &
2312 (SCSMR_CKEDG | SCSMR_SRC_MASK | SCSMR_CKS);
2313 dev_dbg(port->dev, "SCR 0x%x SMR 0x%x\n", scr_val, smr_val);
2314 serial_port_out(port, SCSCR, scr_val);
2315 serial_port_out(port, SCSMR, smr_val);
2316 }
2317
2318 sci_init_pins(port, termios->c_cflag);
2319
2320 port->status &= ~UPSTAT_AUTOCTS;
2321 s->autorts = false;
2322 reg = sci_getreg(port, SCFCR);
2323 if (reg->size) {
2324 unsigned short ctrl = serial_port_in(port, SCFCR);
2325
2326 if ((port->flags & UPF_HARD_FLOW) &&
2327 (termios->c_cflag & CRTSCTS)) {
2328 /* There is no CTS interrupt to restart the hardware */
2329 port->status |= UPSTAT_AUTOCTS;
2330 /* MCE is enabled when RTS is raised */
2331 s->autorts = true;
2332 }
2333
2334 /*
2335 * As we've done a sci_reset() above, ensure we don't
2336 * interfere with the FIFOs while toggling MCE. As the
2337 * reset values could still be set, simply mask them out.
2338 */
2339 ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST);
2340
2341 serial_port_out(port, SCFCR, ctrl);
2342 }
2343
2344 scr_val |= s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0);
2345 dev_dbg(port->dev, "SCSCR 0x%x\n", scr_val);
2346 serial_port_out(port, SCSCR, scr_val);
2347 if ((srr + 1 == 5) &&
2348 (port->type == PORT_SCIFA || port->type == PORT_SCIFB)) {
2349 /*
2350 * In asynchronous mode, when the sampling rate is 1/5, first
2351 * received data may become invalid on some SCIFA and SCIFB.
2352 * To avoid this problem wait more than 1 serial data time (1
2353 * bit time x serial data number) after setting SCSCR.RE = 1.
2354 */
2355 udelay(DIV_ROUND_UP(10 * 1000000, baud));
2356 }
2357
2358#ifdef CONFIG_SERIAL_SH_SCI_DMA
2359 /*
2360 * Calculate delay for 2 DMA buffers (4 FIFO).
2361 * See serial_core.c::uart_update_timeout().
2362 * With 10 bits (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above
2363 * function calculates 1 jiffie for the data plus 5 jiffies for the
2364 * "slop(e)." Then below we calculate 5 jiffies (20ms) for 2 DMA
2365 * buffers (4 FIFO sizes), but when performing a faster transfer, the
2366 * value obtained by this formula is too small. Therefore, if the value
2367 * is smaller than 20ms, use 20ms as the timeout value for DMA.
2368 */
2369 if (s->chan_rx) {
2370 unsigned int bits;
2371
2372 /* byte size and parity */
2373 switch (termios->c_cflag & CSIZE) {
2374 case CS5:
2375 bits = 7;
2376 break;
2377 case CS6:
2378 bits = 8;
2379 break;
2380 case CS7:
2381 bits = 9;
2382 break;
2383 default:
2384 bits = 10;
2385 break;
2386 }
2387
2388 if (termios->c_cflag & CSTOPB)
2389 bits++;
2390 if (termios->c_cflag & PARENB)
2391 bits++;
2392 s->rx_timeout = DIV_ROUND_UP((s->buf_len_rx * 2 * bits * HZ) /
2393 (baud / 10), 10);
2394 dev_dbg(port->dev, "DMA Rx t-out %ums, tty t-out %u jiffies\n",
2395 s->rx_timeout * 1000 / HZ, port->timeout);
2396 if (s->rx_timeout < msecs_to_jiffies(20))
2397 s->rx_timeout = msecs_to_jiffies(20);
2398 }
2399#endif
2400
2401 if ((termios->c_cflag & CREAD) != 0)
2402 sci_start_rx(port);
2403
2404 sci_port_disable(s);
2405
2406 if (UART_ENABLE_MS(port, termios->c_cflag))
2407 sci_enable_ms(port);
2408}
2409
2410static void sci_pm(struct uart_port *port, unsigned int state,
2411 unsigned int oldstate)
2412{
2413 struct sci_port *sci_port = to_sci_port(port);
2414
2415 switch (state) {
2416 case UART_PM_STATE_OFF:
2417 sci_port_disable(sci_port);
2418 break;
2419 default:
2420 sci_port_enable(sci_port);
2421 break;
2422 }
2423}
2424
2425static const char *sci_type(struct uart_port *port)
2426{
2427 switch (port->type) {
2428 case PORT_IRDA:
2429 return "irda";
2430 case PORT_SCI:
2431 return "sci";
2432 case PORT_SCIF:
2433 return "scif";
2434 case PORT_SCIFA:
2435 return "scifa";
2436 case PORT_SCIFB:
2437 return "scifb";
2438 case PORT_HSCIF:
2439 return "hscif";
2440 }
2441
2442 return NULL;
2443}
2444
2445static int sci_remap_port(struct uart_port *port)
2446{
2447 struct sci_port *sport = to_sci_port(port);
2448
2449 /*
2450 * Nothing to do if there's already an established membase.
2451 */
2452 if (port->membase)
2453 return 0;
2454
2455 if (port->flags & UPF_IOREMAP) {
2456 port->membase = ioremap_nocache(port->mapbase, sport->reg_size);
2457 if (unlikely(!port->membase)) {
2458 dev_err(port->dev, "can't remap port#%d\n", port->line);
2459 return -ENXIO;
2460 }
2461 } else {
2462 /*
2463 * For the simple (and majority of) cases where we don't
2464 * need to do any remapping, just cast the cookie
2465 * directly.
2466 */
2467 port->membase = (void __iomem *)(uintptr_t)port->mapbase;
2468 }
2469
2470 return 0;
2471}
2472
2473static void sci_release_port(struct uart_port *port)
2474{
2475 struct sci_port *sport = to_sci_port(port);
2476
2477 if (port->flags & UPF_IOREMAP) {
2478 iounmap(port->membase);
2479 port->membase = NULL;
2480 }
2481
2482 release_mem_region(port->mapbase, sport->reg_size);
2483}
2484
2485static int sci_request_port(struct uart_port *port)
2486{
2487 struct resource *res;
2488 struct sci_port *sport = to_sci_port(port);
2489 int ret;
2490
2491 res = request_mem_region(port->mapbase, sport->reg_size,
2492 dev_name(port->dev));
2493 if (unlikely(res == NULL)) {
2494 dev_err(port->dev, "request_mem_region failed.");
2495 return -EBUSY;
2496 }
2497
2498 ret = sci_remap_port(port);
2499 if (unlikely(ret != 0)) {
2500 release_resource(res);
2501 return ret;
2502 }
2503
2504 return 0;
2505}
2506
2507static void sci_config_port(struct uart_port *port, int flags)
2508{
2509 if (flags & UART_CONFIG_TYPE) {
2510 struct sci_port *sport = to_sci_port(port);
2511
2512 port->type = sport->cfg->type;
2513 sci_request_port(port);
2514 }
2515}
2516
2517static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
2518{
2519 if (ser->baud_base < 2400)
2520 /* No paper tape reader for Mitch.. */
2521 return -EINVAL;
2522
2523 return 0;
2524}
2525
2526static const struct uart_ops sci_uart_ops = {
2527 .tx_empty = sci_tx_empty,
2528 .set_mctrl = sci_set_mctrl,
2529 .get_mctrl = sci_get_mctrl,
2530 .start_tx = sci_start_tx,
2531 .stop_tx = sci_stop_tx,
2532 .stop_rx = sci_stop_rx,
2533 .enable_ms = sci_enable_ms,
2534 .break_ctl = sci_break_ctl,
2535 .startup = sci_startup,
2536 .shutdown = sci_shutdown,
2537 .set_termios = sci_set_termios,
2538 .pm = sci_pm,
2539 .type = sci_type,
2540 .release_port = sci_release_port,
2541 .request_port = sci_request_port,
2542 .config_port = sci_config_port,
2543 .verify_port = sci_verify_port,
2544#ifdef CONFIG_CONSOLE_POLL
2545 .poll_get_char = sci_poll_get_char,
2546 .poll_put_char = sci_poll_put_char,
2547#endif
2548};
2549
2550static int sci_init_clocks(struct sci_port *sci_port, struct device *dev)
2551{
2552 const char *clk_names[] = {
2553 [SCI_FCK] = "fck",
2554 [SCI_SCK] = "sck",
2555 [SCI_BRG_INT] = "brg_int",
2556 [SCI_SCIF_CLK] = "scif_clk",
2557 };
2558 struct clk *clk;
2559 unsigned int i;
2560
2561 if (sci_port->cfg->type == PORT_HSCIF)
2562 clk_names[SCI_SCK] = "hsck";
2563
2564 for (i = 0; i < SCI_NUM_CLKS; i++) {
2565 clk = devm_clk_get(dev, clk_names[i]);
2566 if (PTR_ERR(clk) == -EPROBE_DEFER)
2567 return -EPROBE_DEFER;
2568
2569 if (IS_ERR(clk) && i == SCI_FCK) {
2570 /*
2571 * "fck" used to be called "sci_ick", and we need to
2572 * maintain DT backward compatibility.
2573 */
2574 clk = devm_clk_get(dev, "sci_ick");
2575 if (PTR_ERR(clk) == -EPROBE_DEFER)
2576 return -EPROBE_DEFER;
2577
2578 if (!IS_ERR(clk))
2579 goto found;
2580
2581 /*
2582 * Not all SH platforms declare a clock lookup entry
2583 * for SCI devices, in which case we need to get the
2584 * global "peripheral_clk" clock.
2585 */
2586 clk = devm_clk_get(dev, "peripheral_clk");
2587 if (!IS_ERR(clk))
2588 goto found;
2589
2590 dev_err(dev, "failed to get %s (%ld)\n", clk_names[i],
2591 PTR_ERR(clk));
2592 return PTR_ERR(clk);
2593 }
2594
2595found:
2596 if (IS_ERR(clk))
2597 dev_dbg(dev, "failed to get %s (%ld)\n", clk_names[i],
2598 PTR_ERR(clk));
2599 else
2600 dev_dbg(dev, "clk %s is %pC rate %pCr\n", clk_names[i],
2601 clk, clk);
2602 sci_port->clks[i] = IS_ERR(clk) ? NULL : clk;
2603 }
2604 return 0;
2605}
2606
2607static int sci_init_single(struct platform_device *dev,
2608 struct sci_port *sci_port, unsigned int index,
2609 struct plat_sci_port *p, bool early)
2610{
2611 struct uart_port *port = &sci_port->port;
2612 const struct resource *res;
2613 unsigned int i;
2614 int ret;
2615
2616 sci_port->cfg = p;
2617
2618 port->ops = &sci_uart_ops;
2619 port->iotype = UPIO_MEM;
2620 port->line = index;
2621
2622 res = platform_get_resource(dev, IORESOURCE_MEM, 0);
2623 if (res == NULL)
2624 return -ENOMEM;
2625
2626 port->mapbase = res->start;
2627 sci_port->reg_size = resource_size(res);
2628
2629 for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i)
2630 sci_port->irqs[i] = platform_get_irq(dev, i);
2631
2632 /* The SCI generates several interrupts. They can be muxed together or
2633 * connected to different interrupt lines. In the muxed case only one
2634 * interrupt resource is specified. In the non-muxed case three or four
2635 * interrupt resources are specified, as the BRI interrupt is optional.
2636 */
2637 if (sci_port->irqs[0] < 0)
2638 return -ENXIO;
2639
2640 if (sci_port->irqs[1] < 0) {
2641 sci_port->irqs[1] = sci_port->irqs[0];
2642 sci_port->irqs[2] = sci_port->irqs[0];
2643 sci_port->irqs[3] = sci_port->irqs[0];
2644 }
2645
2646 if (p->regtype == SCIx_PROBE_REGTYPE) {
2647 ret = sci_probe_regmap(p);
2648 if (unlikely(ret))
2649 return ret;
2650 }
2651
2652 switch (p->type) {
2653 case PORT_SCIFB:
2654 port->fifosize = 256;
2655 sci_port->overrun_reg = SCxSR;
2656 sci_port->overrun_mask = SCIFA_ORER;
2657 sci_port->sampling_rate_mask = SCI_SR_SCIFAB;
2658 break;
2659 case PORT_HSCIF:
2660 port->fifosize = 128;
2661 sci_port->overrun_reg = SCLSR;
2662 sci_port->overrun_mask = SCLSR_ORER;
2663 sci_port->sampling_rate_mask = SCI_SR_RANGE(8, 32);
2664 break;
2665 case PORT_SCIFA:
2666 port->fifosize = 64;
2667 sci_port->overrun_reg = SCxSR;
2668 sci_port->overrun_mask = SCIFA_ORER;
2669 sci_port->sampling_rate_mask = SCI_SR_SCIFAB;
2670 break;
2671 case PORT_SCIF:
2672 port->fifosize = 16;
2673 if (p->regtype == SCIx_SH7705_SCIF_REGTYPE) {
2674 sci_port->overrun_reg = SCxSR;
2675 sci_port->overrun_mask = SCIFA_ORER;
2676 sci_port->sampling_rate_mask = SCI_SR(16);
2677 } else {
2678 sci_port->overrun_reg = SCLSR;
2679 sci_port->overrun_mask = SCLSR_ORER;
2680 sci_port->sampling_rate_mask = SCI_SR(32);
2681 }
2682 break;
2683 default:
2684 port->fifosize = 1;
2685 sci_port->overrun_reg = SCxSR;
2686 sci_port->overrun_mask = SCI_ORER;
2687 sci_port->sampling_rate_mask = SCI_SR(32);
2688 break;
2689 }
2690
2691 /* SCIFA on sh7723 and sh7724 need a custom sampling rate that doesn't
2692 * match the SoC datasheet, this should be investigated. Let platform
2693 * data override the sampling rate for now.
2694 */
2695 if (p->sampling_rate)
2696 sci_port->sampling_rate_mask = SCI_SR(p->sampling_rate);
2697
2698 if (!early) {
2699 ret = sci_init_clocks(sci_port, &dev->dev);
2700 if (ret < 0)
2701 return ret;
2702
2703 port->dev = &dev->dev;
2704
2705 pm_runtime_enable(&dev->dev);
2706 }
2707
2708 sci_port->break_timer.data = (unsigned long)sci_port;
2709 sci_port->break_timer.function = sci_break_timer;
2710 init_timer(&sci_port->break_timer);
2711
2712 /*
2713 * Establish some sensible defaults for the error detection.
2714 */
2715 if (p->type == PORT_SCI) {
2716 sci_port->error_mask = SCI_DEFAULT_ERROR_MASK;
2717 sci_port->error_clear = SCI_ERROR_CLEAR;
2718 } else {
2719 sci_port->error_mask = SCIF_DEFAULT_ERROR_MASK;
2720 sci_port->error_clear = SCIF_ERROR_CLEAR;
2721 }
2722
2723 /*
2724 * Make the error mask inclusive of overrun detection, if
2725 * supported.
2726 */
2727 if (sci_port->overrun_reg == SCxSR) {
2728 sci_port->error_mask |= sci_port->overrun_mask;
2729 sci_port->error_clear &= ~sci_port->overrun_mask;
2730 }
2731
2732 port->type = p->type;
2733 port->flags = UPF_FIXED_PORT | p->flags;
2734 port->regshift = p->regshift;
2735
2736 /*
2737 * The UART port needs an IRQ value, so we peg this to the RX IRQ
2738 * for the multi-IRQ ports, which is where we are primarily
2739 * concerned with the shutdown path synchronization.
2740 *
2741 * For the muxed case there's nothing more to do.
2742 */
2743 port->irq = sci_port->irqs[SCIx_RXI_IRQ];
2744 port->irqflags = 0;
2745
2746 port->serial_in = sci_serial_in;
2747 port->serial_out = sci_serial_out;
2748
2749 if (p->dma_slave_tx > 0 && p->dma_slave_rx > 0)
2750 dev_dbg(port->dev, "DMA tx %d, rx %d\n",
2751 p->dma_slave_tx, p->dma_slave_rx);
2752
2753 return 0;
2754}
2755
2756static void sci_cleanup_single(struct sci_port *port)
2757{
2758 pm_runtime_disable(port->port.dev);
2759}
2760
2761#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \
2762 defined(CONFIG_SERIAL_SH_SCI_EARLYCON)
2763static void serial_console_putchar(struct uart_port *port, int ch)
2764{
2765 sci_poll_put_char(port, ch);
2766}
2767
2768/*
2769 * Print a string to the serial port trying not to disturb
2770 * any possible real use of the port...
2771 */
2772static void serial_console_write(struct console *co, const char *s,
2773 unsigned count)
2774{
2775 struct sci_port *sci_port = &sci_ports[co->index];
2776 struct uart_port *port = &sci_port->port;
2777 unsigned short bits, ctrl, ctrl_temp;
2778 unsigned long flags;
2779 int locked = 1;
2780
2781 local_irq_save(flags);
2782#if defined(SUPPORT_SYSRQ)
2783 if (port->sysrq)
2784 locked = 0;
2785 else
2786#endif
2787 if (oops_in_progress)
2788 locked = spin_trylock(&port->lock);
2789 else
2790 spin_lock(&port->lock);
2791
2792 /* first save SCSCR then disable interrupts, keep clock source */
2793 ctrl = serial_port_in(port, SCSCR);
2794 ctrl_temp = (sci_port->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0)) |
2795 (ctrl & (SCSCR_CKE1 | SCSCR_CKE0));
2796 serial_port_out(port, SCSCR, ctrl_temp);
2797
2798 uart_console_write(port, s, count, serial_console_putchar);
2799
2800 /* wait until fifo is empty and last bit has been transmitted */
2801 bits = SCxSR_TDxE(port) | SCxSR_TEND(port);
2802 while ((serial_port_in(port, SCxSR) & bits) != bits)
2803 cpu_relax();
2804
2805 /* restore the SCSCR */
2806 serial_port_out(port, SCSCR, ctrl);
2807
2808 if (locked)
2809 spin_unlock(&port->lock);
2810 local_irq_restore(flags);
2811}
2812
2813static int serial_console_setup(struct console *co, char *options)
2814{
2815 struct sci_port *sci_port;
2816 struct uart_port *port;
2817 int baud = 115200;
2818 int bits = 8;
2819 int parity = 'n';
2820 int flow = 'n';
2821 int ret;
2822
2823 /*
2824 * Refuse to handle any bogus ports.
2825 */
2826 if (co->index < 0 || co->index >= SCI_NPORTS)
2827 return -ENODEV;
2828
2829 sci_port = &sci_ports[co->index];
2830 port = &sci_port->port;
2831
2832 /*
2833 * Refuse to handle uninitialized ports.
2834 */
2835 if (!port->ops)
2836 return -ENODEV;
2837
2838 ret = sci_remap_port(port);
2839 if (unlikely(ret != 0))
2840 return ret;
2841
2842 if (options)
2843 uart_parse_options(options, &baud, &parity, &bits, &flow);
2844
2845 return uart_set_options(port, co, baud, parity, bits, flow);
2846}
2847
2848static struct console serial_console = {
2849 .name = "ttySC",
2850 .device = uart_console_device,
2851 .write = serial_console_write,
2852 .setup = serial_console_setup,
2853 .flags = CON_PRINTBUFFER,
2854 .index = -1,
2855 .data = &sci_uart_driver,
2856};
2857
2858static struct console early_serial_console = {
2859 .name = "early_ttySC",
2860 .write = serial_console_write,
2861 .flags = CON_PRINTBUFFER,
2862 .index = -1,
2863};
2864
2865static char early_serial_buf[32];
2866
2867static int sci_probe_earlyprintk(struct platform_device *pdev)
2868{
2869 struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev);
2870
2871 if (early_serial_console.data)
2872 return -EEXIST;
2873
2874 early_serial_console.index = pdev->id;
2875
2876 sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true);
2877
2878 serial_console_setup(&early_serial_console, early_serial_buf);
2879
2880 if (!strstr(early_serial_buf, "keep"))
2881 early_serial_console.flags |= CON_BOOT;
2882
2883 register_console(&early_serial_console);
2884 return 0;
2885}
2886
2887#define SCI_CONSOLE (&serial_console)
2888
2889#else
2890static inline int sci_probe_earlyprintk(struct platform_device *pdev)
2891{
2892 return -EINVAL;
2893}
2894
2895#define SCI_CONSOLE NULL
2896
2897#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE || CONFIG_SERIAL_SH_SCI_EARLYCON */
2898
2899static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized";
2900
2901static struct uart_driver sci_uart_driver = {
2902 .owner = THIS_MODULE,
2903 .driver_name = "sci",
2904 .dev_name = "ttySC",
2905 .major = SCI_MAJOR,
2906 .minor = SCI_MINOR_START,
2907 .nr = SCI_NPORTS,
2908 .cons = SCI_CONSOLE,
2909};
2910
2911static int sci_remove(struct platform_device *dev)
2912{
2913 struct sci_port *port = platform_get_drvdata(dev);
2914
2915 uart_remove_one_port(&sci_uart_driver, &port->port);
2916
2917 sci_cleanup_single(port);
2918
2919 return 0;
2920}
2921
2922
2923#define SCI_OF_DATA(type, regtype) (void *)((type) << 16 | (regtype))
2924#define SCI_OF_TYPE(data) ((unsigned long)(data) >> 16)
2925#define SCI_OF_REGTYPE(data) ((unsigned long)(data) & 0xffff)
2926
2927static const struct of_device_id of_sci_match[] = {
2928 /* SoC-specific types */
2929 {
2930 .compatible = "renesas,scif-r7s72100",
2931 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH2_SCIF_FIFODATA_REGTYPE),
2932 },
2933 /* Family-specific types */
2934 {
2935 .compatible = "renesas,rcar-gen1-scif",
2936 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
2937 }, {
2938 .compatible = "renesas,rcar-gen2-scif",
2939 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
2940 }, {
2941 .compatible = "renesas,rcar-gen3-scif",
2942 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE),
2943 },
2944 /* Generic types */
2945 {
2946 .compatible = "renesas,scif",
2947 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_REGTYPE),
2948 }, {
2949 .compatible = "renesas,scifa",
2950 .data = SCI_OF_DATA(PORT_SCIFA, SCIx_SCIFA_REGTYPE),
2951 }, {
2952 .compatible = "renesas,scifb",
2953 .data = SCI_OF_DATA(PORT_SCIFB, SCIx_SCIFB_REGTYPE),
2954 }, {
2955 .compatible = "renesas,hscif",
2956 .data = SCI_OF_DATA(PORT_HSCIF, SCIx_HSCIF_REGTYPE),
2957 }, {
2958 .compatible = "renesas,sci",
2959 .data = SCI_OF_DATA(PORT_SCI, SCIx_SCI_REGTYPE),
2960 }, {
2961 /* Terminator */
2962 },
2963};
2964MODULE_DEVICE_TABLE(of, of_sci_match);
2965
2966static struct plat_sci_port *
2967sci_parse_dt(struct platform_device *pdev, unsigned int *dev_id)
2968{
2969 struct device_node *np = pdev->dev.of_node;
2970 const struct of_device_id *match;
2971 struct plat_sci_port *p;
2972 int id;
2973
2974 if (!IS_ENABLED(CONFIG_OF) || !np)
2975 return NULL;
2976
2977 match = of_match_node(of_sci_match, np);
2978 if (!match)
2979 return NULL;
2980
2981 p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
2982 if (!p)
2983 return NULL;
2984
2985 /* Get the line number from the aliases node. */
2986 id = of_alias_get_id(np, "serial");
2987 if (id < 0) {
2988 dev_err(&pdev->dev, "failed to get alias id (%d)\n", id);
2989 return NULL;
2990 }
2991
2992 *dev_id = id;
2993
2994 p->flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
2995 p->type = SCI_OF_TYPE(match->data);
2996 p->regtype = SCI_OF_REGTYPE(match->data);
2997 p->scscr = SCSCR_RE | SCSCR_TE;
2998
2999 if (of_find_property(np, "uart-has-rtscts", NULL))
3000 p->capabilities |= SCIx_HAVE_RTSCTS;
3001
3002 return p;
3003}
3004
3005static int sci_probe_single(struct platform_device *dev,
3006 unsigned int index,
3007 struct plat_sci_port *p,
3008 struct sci_port *sciport)
3009{
3010 int ret;
3011
3012 /* Sanity check */
3013 if (unlikely(index >= SCI_NPORTS)) {
3014 dev_notice(&dev->dev, "Attempting to register port %d when only %d are available\n",
3015 index+1, SCI_NPORTS);
3016 dev_notice(&dev->dev, "Consider bumping CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
3017 return -EINVAL;
3018 }
3019
3020 ret = sci_init_single(dev, sciport, index, p, false);
3021 if (ret)
3022 return ret;
3023
3024 sciport->gpios = mctrl_gpio_init(&sciport->port, 0);
3025 if (IS_ERR(sciport->gpios) && PTR_ERR(sciport->gpios) != -ENOSYS)
3026 return PTR_ERR(sciport->gpios);
3027
3028 if (p->capabilities & SCIx_HAVE_RTSCTS) {
3029 if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(sciport->gpios,
3030 UART_GPIO_CTS)) ||
3031 !IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(sciport->gpios,
3032 UART_GPIO_RTS))) {
3033 dev_err(&dev->dev, "Conflicting RTS/CTS config\n");
3034 return -EINVAL;
3035 }
3036 sciport->port.flags |= UPF_HARD_FLOW;
3037 }
3038
3039 ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
3040 if (ret) {
3041 sci_cleanup_single(sciport);
3042 return ret;
3043 }
3044
3045 return 0;
3046}
3047
3048static int sci_probe(struct platform_device *dev)
3049{
3050 struct plat_sci_port *p;
3051 struct sci_port *sp;
3052 unsigned int dev_id;
3053 int ret;
3054
3055 /*
3056 * If we've come here via earlyprintk initialization, head off to
3057 * the special early probe. We don't have sufficient device state
3058 * to make it beyond this yet.
3059 */
3060 if (is_early_platform_device(dev))
3061 return sci_probe_earlyprintk(dev);
3062
3063 if (dev->dev.of_node) {
3064 p = sci_parse_dt(dev, &dev_id);
3065 if (p == NULL)
3066 return -EINVAL;
3067 } else {
3068 p = dev->dev.platform_data;
3069 if (p == NULL) {
3070 dev_err(&dev->dev, "no platform data supplied\n");
3071 return -EINVAL;
3072 }
3073
3074 dev_id = dev->id;
3075 }
3076
3077 sp = &sci_ports[dev_id];
3078 platform_set_drvdata(dev, sp);
3079
3080 ret = sci_probe_single(dev, dev_id, p, sp);
3081 if (ret)
3082 return ret;
3083
3084#ifdef CONFIG_SH_STANDARD_BIOS
3085 sh_bios_gdb_detach();
3086#endif
3087
3088 return 0;
3089}
3090
3091static __maybe_unused int sci_suspend(struct device *dev)
3092{
3093 struct sci_port *sport = dev_get_drvdata(dev);
3094
3095 if (sport)
3096 uart_suspend_port(&sci_uart_driver, &sport->port);
3097
3098 return 0;
3099}
3100
3101static __maybe_unused int sci_resume(struct device *dev)
3102{
3103 struct sci_port *sport = dev_get_drvdata(dev);
3104
3105 if (sport)
3106 uart_resume_port(&sci_uart_driver, &sport->port);
3107
3108 return 0;
3109}
3110
3111static SIMPLE_DEV_PM_OPS(sci_dev_pm_ops, sci_suspend, sci_resume);
3112
3113static struct platform_driver sci_driver = {
3114 .probe = sci_probe,
3115 .remove = sci_remove,
3116 .driver = {
3117 .name = "sh-sci",
3118 .pm = &sci_dev_pm_ops,
3119 .of_match_table = of_match_ptr(of_sci_match),
3120 },
3121};
3122
3123static int __init sci_init(void)
3124{
3125 int ret;
3126
3127 pr_info("%s\n", banner);
3128
3129 ret = uart_register_driver(&sci_uart_driver);
3130 if (likely(ret == 0)) {
3131 ret = platform_driver_register(&sci_driver);
3132 if (unlikely(ret))
3133 uart_unregister_driver(&sci_uart_driver);
3134 }
3135
3136 return ret;
3137}
3138
3139static void __exit sci_exit(void)
3140{
3141 platform_driver_unregister(&sci_driver);
3142 uart_unregister_driver(&sci_uart_driver);
3143}
3144
3145#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
3146early_platform_init_buffer("earlyprintk", &sci_driver,
3147 early_serial_buf, ARRAY_SIZE(early_serial_buf));
3148#endif
3149#ifdef CONFIG_SERIAL_SH_SCI_EARLYCON
3150static struct __init plat_sci_port port_cfg;
3151
3152static int __init early_console_setup(struct earlycon_device *device,
3153 int type)
3154{
3155 if (!device->port.membase)
3156 return -ENODEV;
3157
3158 device->port.serial_in = sci_serial_in;
3159 device->port.serial_out = sci_serial_out;
3160 device->port.type = type;
3161 memcpy(&sci_ports[0].port, &device->port, sizeof(struct uart_port));
3162 sci_ports[0].cfg = &port_cfg;
3163 sci_ports[0].cfg->type = type;
3164 sci_probe_regmap(sci_ports[0].cfg);
3165 port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR) |
3166 SCSCR_RE | SCSCR_TE;
3167 sci_serial_out(&sci_ports[0].port, SCSCR, port_cfg.scscr);
3168
3169 device->con->write = serial_console_write;
3170 return 0;
3171}
3172static int __init sci_early_console_setup(struct earlycon_device *device,
3173 const char *opt)
3174{
3175 return early_console_setup(device, PORT_SCI);
3176}
3177static int __init scif_early_console_setup(struct earlycon_device *device,
3178 const char *opt)
3179{
3180 return early_console_setup(device, PORT_SCIF);
3181}
3182static int __init scifa_early_console_setup(struct earlycon_device *device,
3183 const char *opt)
3184{
3185 return early_console_setup(device, PORT_SCIFA);
3186}
3187static int __init scifb_early_console_setup(struct earlycon_device *device,
3188 const char *opt)
3189{
3190 return early_console_setup(device, PORT_SCIFB);
3191}
3192static int __init hscif_early_console_setup(struct earlycon_device *device,
3193 const char *opt)
3194{
3195 return early_console_setup(device, PORT_HSCIF);
3196}
3197
3198OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup);
3199OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup);
3200OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup);
3201OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup);
3202OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup);
3203#endif /* CONFIG_SERIAL_SH_SCI_EARLYCON */
3204
3205module_init(sci_init);
3206module_exit(sci_exit);
3207
3208MODULE_LICENSE("GPL");
3209MODULE_ALIAS("platform:sh-sci");
3210MODULE_AUTHOR("Paul Mundt");
3211MODULE_DESCRIPTION("SuperH (H)SCI(F) serial driver");