Loading...
1/*
2 * rtc-ds1307.c - RTC driver for some mostly-compatible I2C chips.
3 *
4 * Copyright (C) 2005 James Chapman (ds1337 core)
5 * Copyright (C) 2006 David Brownell
6 * Copyright (C) 2009 Matthias Fuchs (rx8025 support)
7 * Copyright (C) 2012 Bertrand Achard (nvram access fixes)
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
12 */
13
14#include <linux/bcd.h>
15#include <linux/i2c.h>
16#include <linux/init.h>
17#include <linux/module.h>
18#include <linux/rtc/ds1307.h>
19#include <linux/rtc.h>
20#include <linux/slab.h>
21#include <linux/string.h>
22#include <linux/hwmon.h>
23#include <linux/hwmon-sysfs.h>
24#include <linux/clk-provider.h>
25
26/*
27 * We can't determine type by probing, but if we expect pre-Linux code
28 * to have set the chip up as a clock (turning on the oscillator and
29 * setting the date and time), Linux can ignore the non-clock features.
30 * That's a natural job for a factory or repair bench.
31 */
32enum ds_type {
33 ds_1307,
34 ds_1337,
35 ds_1338,
36 ds_1339,
37 ds_1340,
38 ds_1388,
39 ds_3231,
40 m41t00,
41 mcp794xx,
42 rx_8025,
43 last_ds_type /* always last */
44 /* rs5c372 too? different address... */
45};
46
47
48/* RTC registers don't differ much, except for the century flag */
49#define DS1307_REG_SECS 0x00 /* 00-59 */
50# define DS1307_BIT_CH 0x80
51# define DS1340_BIT_nEOSC 0x80
52# define MCP794XX_BIT_ST 0x80
53#define DS1307_REG_MIN 0x01 /* 00-59 */
54#define DS1307_REG_HOUR 0x02 /* 00-23, or 1-12{am,pm} */
55# define DS1307_BIT_12HR 0x40 /* in REG_HOUR */
56# define DS1307_BIT_PM 0x20 /* in REG_HOUR */
57# define DS1340_BIT_CENTURY_EN 0x80 /* in REG_HOUR */
58# define DS1340_BIT_CENTURY 0x40 /* in REG_HOUR */
59#define DS1307_REG_WDAY 0x03 /* 01-07 */
60# define MCP794XX_BIT_VBATEN 0x08
61#define DS1307_REG_MDAY 0x04 /* 01-31 */
62#define DS1307_REG_MONTH 0x05 /* 01-12 */
63# define DS1337_BIT_CENTURY 0x80 /* in REG_MONTH */
64#define DS1307_REG_YEAR 0x06 /* 00-99 */
65
66/*
67 * Other registers (control, status, alarms, trickle charge, NVRAM, etc)
68 * start at 7, and they differ a LOT. Only control and status matter for
69 * basic RTC date and time functionality; be careful using them.
70 */
71#define DS1307_REG_CONTROL 0x07 /* or ds1338 */
72# define DS1307_BIT_OUT 0x80
73# define DS1338_BIT_OSF 0x20
74# define DS1307_BIT_SQWE 0x10
75# define DS1307_BIT_RS1 0x02
76# define DS1307_BIT_RS0 0x01
77#define DS1337_REG_CONTROL 0x0e
78# define DS1337_BIT_nEOSC 0x80
79# define DS1339_BIT_BBSQI 0x20
80# define DS3231_BIT_BBSQW 0x40 /* same as BBSQI */
81# define DS1337_BIT_RS2 0x10
82# define DS1337_BIT_RS1 0x08
83# define DS1337_BIT_INTCN 0x04
84# define DS1337_BIT_A2IE 0x02
85# define DS1337_BIT_A1IE 0x01
86#define DS1340_REG_CONTROL 0x07
87# define DS1340_BIT_OUT 0x80
88# define DS1340_BIT_FT 0x40
89# define DS1340_BIT_CALIB_SIGN 0x20
90# define DS1340_M_CALIBRATION 0x1f
91#define DS1340_REG_FLAG 0x09
92# define DS1340_BIT_OSF 0x80
93#define DS1337_REG_STATUS 0x0f
94# define DS1337_BIT_OSF 0x80
95# define DS3231_BIT_EN32KHZ 0x08
96# define DS1337_BIT_A2I 0x02
97# define DS1337_BIT_A1I 0x01
98#define DS1339_REG_ALARM1_SECS 0x07
99
100#define DS13XX_TRICKLE_CHARGER_MAGIC 0xa0
101
102#define RX8025_REG_CTRL1 0x0e
103# define RX8025_BIT_2412 0x20
104#define RX8025_REG_CTRL2 0x0f
105# define RX8025_BIT_PON 0x10
106# define RX8025_BIT_VDET 0x40
107# define RX8025_BIT_XST 0x20
108
109
110struct ds1307 {
111 u8 offset; /* register's offset */
112 u8 regs[11];
113 u16 nvram_offset;
114 struct bin_attribute *nvram;
115 enum ds_type type;
116 unsigned long flags;
117#define HAS_NVRAM 0 /* bit 0 == sysfs file active */
118#define HAS_ALARM 1 /* bit 1 == irq claimed */
119 struct i2c_client *client;
120 struct rtc_device *rtc;
121 s32 (*read_block_data)(const struct i2c_client *client, u8 command,
122 u8 length, u8 *values);
123 s32 (*write_block_data)(const struct i2c_client *client, u8 command,
124 u8 length, const u8 *values);
125#ifdef CONFIG_COMMON_CLK
126 struct clk_hw clks[2];
127#endif
128};
129
130struct chip_desc {
131 unsigned alarm:1;
132 u16 nvram_offset;
133 u16 nvram_size;
134 u16 trickle_charger_reg;
135 u8 trickle_charger_setup;
136 u8 (*do_trickle_setup)(struct i2c_client *, uint32_t, bool);
137};
138
139static u8 do_trickle_setup_ds1339(struct i2c_client *,
140 uint32_t ohms, bool diode);
141
142static struct chip_desc chips[last_ds_type] = {
143 [ds_1307] = {
144 .nvram_offset = 8,
145 .nvram_size = 56,
146 },
147 [ds_1337] = {
148 .alarm = 1,
149 },
150 [ds_1338] = {
151 .nvram_offset = 8,
152 .nvram_size = 56,
153 },
154 [ds_1339] = {
155 .alarm = 1,
156 .trickle_charger_reg = 0x10,
157 .do_trickle_setup = &do_trickle_setup_ds1339,
158 },
159 [ds_1340] = {
160 .trickle_charger_reg = 0x08,
161 },
162 [ds_1388] = {
163 .trickle_charger_reg = 0x0a,
164 },
165 [ds_3231] = {
166 .alarm = 1,
167 },
168 [mcp794xx] = {
169 .alarm = 1,
170 /* this is battery backed SRAM */
171 .nvram_offset = 0x20,
172 .nvram_size = 0x40,
173 },
174};
175
176static const struct i2c_device_id ds1307_id[] = {
177 { "ds1307", ds_1307 },
178 { "ds1337", ds_1337 },
179 { "ds1338", ds_1338 },
180 { "ds1339", ds_1339 },
181 { "ds1388", ds_1388 },
182 { "ds1340", ds_1340 },
183 { "ds3231", ds_3231 },
184 { "m41t00", m41t00 },
185 { "mcp7940x", mcp794xx },
186 { "mcp7941x", mcp794xx },
187 { "pt7c4338", ds_1307 },
188 { "rx8025", rx_8025 },
189 { }
190};
191MODULE_DEVICE_TABLE(i2c, ds1307_id);
192
193/*----------------------------------------------------------------------*/
194
195#define BLOCK_DATA_MAX_TRIES 10
196
197static s32 ds1307_read_block_data_once(const struct i2c_client *client,
198 u8 command, u8 length, u8 *values)
199{
200 s32 i, data;
201
202 for (i = 0; i < length; i++) {
203 data = i2c_smbus_read_byte_data(client, command + i);
204 if (data < 0)
205 return data;
206 values[i] = data;
207 }
208 return i;
209}
210
211static s32 ds1307_read_block_data(const struct i2c_client *client, u8 command,
212 u8 length, u8 *values)
213{
214 u8 oldvalues[255];
215 s32 ret;
216 int tries = 0;
217
218 dev_dbg(&client->dev, "ds1307_read_block_data (length=%d)\n", length);
219 ret = ds1307_read_block_data_once(client, command, length, values);
220 if (ret < 0)
221 return ret;
222 do {
223 if (++tries > BLOCK_DATA_MAX_TRIES) {
224 dev_err(&client->dev,
225 "ds1307_read_block_data failed\n");
226 return -EIO;
227 }
228 memcpy(oldvalues, values, length);
229 ret = ds1307_read_block_data_once(client, command, length,
230 values);
231 if (ret < 0)
232 return ret;
233 } while (memcmp(oldvalues, values, length));
234 return length;
235}
236
237static s32 ds1307_write_block_data(const struct i2c_client *client, u8 command,
238 u8 length, const u8 *values)
239{
240 u8 currvalues[255];
241 int tries = 0;
242
243 dev_dbg(&client->dev, "ds1307_write_block_data (length=%d)\n", length);
244 do {
245 s32 i, ret;
246
247 if (++tries > BLOCK_DATA_MAX_TRIES) {
248 dev_err(&client->dev,
249 "ds1307_write_block_data failed\n");
250 return -EIO;
251 }
252 for (i = 0; i < length; i++) {
253 ret = i2c_smbus_write_byte_data(client, command + i,
254 values[i]);
255 if (ret < 0)
256 return ret;
257 }
258 ret = ds1307_read_block_data_once(client, command, length,
259 currvalues);
260 if (ret < 0)
261 return ret;
262 } while (memcmp(currvalues, values, length));
263 return length;
264}
265
266/*----------------------------------------------------------------------*/
267
268/* These RTC devices are not designed to be connected to a SMbus adapter.
269 SMbus limits block operations length to 32 bytes, whereas it's not
270 limited on I2C buses. As a result, accesses may exceed 32 bytes;
271 in that case, split them into smaller blocks */
272
273static s32 ds1307_native_smbus_write_block_data(const struct i2c_client *client,
274 u8 command, u8 length, const u8 *values)
275{
276 u8 suboffset = 0;
277
278 if (length <= I2C_SMBUS_BLOCK_MAX)
279 return i2c_smbus_write_i2c_block_data(client,
280 command, length, values);
281
282 while (suboffset < length) {
283 s32 retval = i2c_smbus_write_i2c_block_data(client,
284 command + suboffset,
285 min(I2C_SMBUS_BLOCK_MAX, length - suboffset),
286 values + suboffset);
287 if (retval < 0)
288 return retval;
289
290 suboffset += I2C_SMBUS_BLOCK_MAX;
291 }
292 return length;
293}
294
295static s32 ds1307_native_smbus_read_block_data(const struct i2c_client *client,
296 u8 command, u8 length, u8 *values)
297{
298 u8 suboffset = 0;
299
300 if (length <= I2C_SMBUS_BLOCK_MAX)
301 return i2c_smbus_read_i2c_block_data(client,
302 command, length, values);
303
304 while (suboffset < length) {
305 s32 retval = i2c_smbus_read_i2c_block_data(client,
306 command + suboffset,
307 min(I2C_SMBUS_BLOCK_MAX, length - suboffset),
308 values + suboffset);
309 if (retval < 0)
310 return retval;
311
312 suboffset += I2C_SMBUS_BLOCK_MAX;
313 }
314 return length;
315}
316
317/*----------------------------------------------------------------------*/
318
319/*
320 * The ds1337 and ds1339 both have two alarms, but we only use the first
321 * one (with a "seconds" field). For ds1337 we expect nINTA is our alarm
322 * signal; ds1339 chips have only one alarm signal.
323 */
324static irqreturn_t ds1307_irq(int irq, void *dev_id)
325{
326 struct i2c_client *client = dev_id;
327 struct ds1307 *ds1307 = i2c_get_clientdata(client);
328 struct mutex *lock = &ds1307->rtc->ops_lock;
329 int stat, control;
330
331 mutex_lock(lock);
332 stat = i2c_smbus_read_byte_data(client, DS1337_REG_STATUS);
333 if (stat < 0)
334 goto out;
335
336 if (stat & DS1337_BIT_A1I) {
337 stat &= ~DS1337_BIT_A1I;
338 i2c_smbus_write_byte_data(client, DS1337_REG_STATUS, stat);
339
340 control = i2c_smbus_read_byte_data(client, DS1337_REG_CONTROL);
341 if (control < 0)
342 goto out;
343
344 control &= ~DS1337_BIT_A1IE;
345 i2c_smbus_write_byte_data(client, DS1337_REG_CONTROL, control);
346
347 rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF);
348 }
349
350out:
351 mutex_unlock(lock);
352
353 return IRQ_HANDLED;
354}
355
356/*----------------------------------------------------------------------*/
357
358static int ds1307_get_time(struct device *dev, struct rtc_time *t)
359{
360 struct ds1307 *ds1307 = dev_get_drvdata(dev);
361 int tmp;
362
363 /* read the RTC date and time registers all at once */
364 tmp = ds1307->read_block_data(ds1307->client,
365 ds1307->offset, 7, ds1307->regs);
366 if (tmp != 7) {
367 dev_err(dev, "%s error %d\n", "read", tmp);
368 return -EIO;
369 }
370
371 dev_dbg(dev, "%s: %7ph\n", "read", ds1307->regs);
372
373 t->tm_sec = bcd2bin(ds1307->regs[DS1307_REG_SECS] & 0x7f);
374 t->tm_min = bcd2bin(ds1307->regs[DS1307_REG_MIN] & 0x7f);
375 tmp = ds1307->regs[DS1307_REG_HOUR] & 0x3f;
376 t->tm_hour = bcd2bin(tmp);
377 t->tm_wday = bcd2bin(ds1307->regs[DS1307_REG_WDAY] & 0x07) - 1;
378 t->tm_mday = bcd2bin(ds1307->regs[DS1307_REG_MDAY] & 0x3f);
379 tmp = ds1307->regs[DS1307_REG_MONTH] & 0x1f;
380 t->tm_mon = bcd2bin(tmp) - 1;
381
382 /* assume 20YY not 19YY, and ignore DS1337_BIT_CENTURY */
383 t->tm_year = bcd2bin(ds1307->regs[DS1307_REG_YEAR]) + 100;
384
385 dev_dbg(dev, "%s secs=%d, mins=%d, "
386 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n",
387 "read", t->tm_sec, t->tm_min,
388 t->tm_hour, t->tm_mday,
389 t->tm_mon, t->tm_year, t->tm_wday);
390
391 /* initial clock setting can be undefined */
392 return rtc_valid_tm(t);
393}
394
395static int ds1307_set_time(struct device *dev, struct rtc_time *t)
396{
397 struct ds1307 *ds1307 = dev_get_drvdata(dev);
398 int result;
399 int tmp;
400 u8 *buf = ds1307->regs;
401
402 dev_dbg(dev, "%s secs=%d, mins=%d, "
403 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n",
404 "write", t->tm_sec, t->tm_min,
405 t->tm_hour, t->tm_mday,
406 t->tm_mon, t->tm_year, t->tm_wday);
407
408 buf[DS1307_REG_SECS] = bin2bcd(t->tm_sec);
409 buf[DS1307_REG_MIN] = bin2bcd(t->tm_min);
410 buf[DS1307_REG_HOUR] = bin2bcd(t->tm_hour);
411 buf[DS1307_REG_WDAY] = bin2bcd(t->tm_wday + 1);
412 buf[DS1307_REG_MDAY] = bin2bcd(t->tm_mday);
413 buf[DS1307_REG_MONTH] = bin2bcd(t->tm_mon + 1);
414
415 /* assume 20YY not 19YY */
416 tmp = t->tm_year - 100;
417 buf[DS1307_REG_YEAR] = bin2bcd(tmp);
418
419 switch (ds1307->type) {
420 case ds_1337:
421 case ds_1339:
422 case ds_3231:
423 buf[DS1307_REG_MONTH] |= DS1337_BIT_CENTURY;
424 break;
425 case ds_1340:
426 buf[DS1307_REG_HOUR] |= DS1340_BIT_CENTURY_EN
427 | DS1340_BIT_CENTURY;
428 break;
429 case mcp794xx:
430 /*
431 * these bits were cleared when preparing the date/time
432 * values and need to be set again before writing the
433 * buffer out to the device.
434 */
435 buf[DS1307_REG_SECS] |= MCP794XX_BIT_ST;
436 buf[DS1307_REG_WDAY] |= MCP794XX_BIT_VBATEN;
437 break;
438 default:
439 break;
440 }
441
442 dev_dbg(dev, "%s: %7ph\n", "write", buf);
443
444 result = ds1307->write_block_data(ds1307->client,
445 ds1307->offset, 7, buf);
446 if (result < 0) {
447 dev_err(dev, "%s error %d\n", "write", result);
448 return result;
449 }
450 return 0;
451}
452
453static int ds1337_read_alarm(struct device *dev, struct rtc_wkalrm *t)
454{
455 struct i2c_client *client = to_i2c_client(dev);
456 struct ds1307 *ds1307 = i2c_get_clientdata(client);
457 int ret;
458
459 if (!test_bit(HAS_ALARM, &ds1307->flags))
460 return -EINVAL;
461
462 /* read all ALARM1, ALARM2, and status registers at once */
463 ret = ds1307->read_block_data(client,
464 DS1339_REG_ALARM1_SECS, 9, ds1307->regs);
465 if (ret != 9) {
466 dev_err(dev, "%s error %d\n", "alarm read", ret);
467 return -EIO;
468 }
469
470 dev_dbg(dev, "%s: %4ph, %3ph, %2ph\n", "alarm read",
471 &ds1307->regs[0], &ds1307->regs[4], &ds1307->regs[7]);
472
473 /*
474 * report alarm time (ALARM1); assume 24 hour and day-of-month modes,
475 * and that all four fields are checked matches
476 */
477 t->time.tm_sec = bcd2bin(ds1307->regs[0] & 0x7f);
478 t->time.tm_min = bcd2bin(ds1307->regs[1] & 0x7f);
479 t->time.tm_hour = bcd2bin(ds1307->regs[2] & 0x3f);
480 t->time.tm_mday = bcd2bin(ds1307->regs[3] & 0x3f);
481 t->time.tm_mon = -1;
482 t->time.tm_year = -1;
483 t->time.tm_wday = -1;
484 t->time.tm_yday = -1;
485 t->time.tm_isdst = -1;
486
487 /* ... and status */
488 t->enabled = !!(ds1307->regs[7] & DS1337_BIT_A1IE);
489 t->pending = !!(ds1307->regs[8] & DS1337_BIT_A1I);
490
491 dev_dbg(dev, "%s secs=%d, mins=%d, "
492 "hours=%d, mday=%d, enabled=%d, pending=%d\n",
493 "alarm read", t->time.tm_sec, t->time.tm_min,
494 t->time.tm_hour, t->time.tm_mday,
495 t->enabled, t->pending);
496
497 return 0;
498}
499
500static int ds1337_set_alarm(struct device *dev, struct rtc_wkalrm *t)
501{
502 struct i2c_client *client = to_i2c_client(dev);
503 struct ds1307 *ds1307 = i2c_get_clientdata(client);
504 unsigned char *buf = ds1307->regs;
505 u8 control, status;
506 int ret;
507
508 if (!test_bit(HAS_ALARM, &ds1307->flags))
509 return -EINVAL;
510
511 dev_dbg(dev, "%s secs=%d, mins=%d, "
512 "hours=%d, mday=%d, enabled=%d, pending=%d\n",
513 "alarm set", t->time.tm_sec, t->time.tm_min,
514 t->time.tm_hour, t->time.tm_mday,
515 t->enabled, t->pending);
516
517 /* read current status of both alarms and the chip */
518 ret = ds1307->read_block_data(client,
519 DS1339_REG_ALARM1_SECS, 9, buf);
520 if (ret != 9) {
521 dev_err(dev, "%s error %d\n", "alarm write", ret);
522 return -EIO;
523 }
524 control = ds1307->regs[7];
525 status = ds1307->regs[8];
526
527 dev_dbg(dev, "%s: %4ph, %3ph, %02x %02x\n", "alarm set (old status)",
528 &ds1307->regs[0], &ds1307->regs[4], control, status);
529
530 /* set ALARM1, using 24 hour and day-of-month modes */
531 buf[0] = bin2bcd(t->time.tm_sec);
532 buf[1] = bin2bcd(t->time.tm_min);
533 buf[2] = bin2bcd(t->time.tm_hour);
534 buf[3] = bin2bcd(t->time.tm_mday);
535
536 /* set ALARM2 to non-garbage */
537 buf[4] = 0;
538 buf[5] = 0;
539 buf[6] = 0;
540
541 /* optionally enable ALARM1 */
542 buf[7] = control & ~(DS1337_BIT_A1IE | DS1337_BIT_A2IE);
543 if (t->enabled) {
544 dev_dbg(dev, "alarm IRQ armed\n");
545 buf[7] |= DS1337_BIT_A1IE; /* only ALARM1 is used */
546 }
547 buf[8] = status & ~(DS1337_BIT_A1I | DS1337_BIT_A2I);
548
549 ret = ds1307->write_block_data(client,
550 DS1339_REG_ALARM1_SECS, 9, buf);
551 if (ret < 0) {
552 dev_err(dev, "can't set alarm time\n");
553 return ret;
554 }
555
556 return 0;
557}
558
559static int ds1307_alarm_irq_enable(struct device *dev, unsigned int enabled)
560{
561 struct i2c_client *client = to_i2c_client(dev);
562 struct ds1307 *ds1307 = i2c_get_clientdata(client);
563 int ret;
564
565 if (!test_bit(HAS_ALARM, &ds1307->flags))
566 return -ENOTTY;
567
568 ret = i2c_smbus_read_byte_data(client, DS1337_REG_CONTROL);
569 if (ret < 0)
570 return ret;
571
572 if (enabled)
573 ret |= DS1337_BIT_A1IE;
574 else
575 ret &= ~DS1337_BIT_A1IE;
576
577 ret = i2c_smbus_write_byte_data(client, DS1337_REG_CONTROL, ret);
578 if (ret < 0)
579 return ret;
580
581 return 0;
582}
583
584static const struct rtc_class_ops ds13xx_rtc_ops = {
585 .read_time = ds1307_get_time,
586 .set_time = ds1307_set_time,
587 .read_alarm = ds1337_read_alarm,
588 .set_alarm = ds1337_set_alarm,
589 .alarm_irq_enable = ds1307_alarm_irq_enable,
590};
591
592/*----------------------------------------------------------------------*/
593
594/*
595 * Alarm support for mcp794xx devices.
596 */
597
598#define MCP794XX_REG_CONTROL 0x07
599# define MCP794XX_BIT_ALM0_EN 0x10
600# define MCP794XX_BIT_ALM1_EN 0x20
601#define MCP794XX_REG_ALARM0_BASE 0x0a
602#define MCP794XX_REG_ALARM0_CTRL 0x0d
603#define MCP794XX_REG_ALARM1_BASE 0x11
604#define MCP794XX_REG_ALARM1_CTRL 0x14
605# define MCP794XX_BIT_ALMX_IF (1 << 3)
606# define MCP794XX_BIT_ALMX_C0 (1 << 4)
607# define MCP794XX_BIT_ALMX_C1 (1 << 5)
608# define MCP794XX_BIT_ALMX_C2 (1 << 6)
609# define MCP794XX_BIT_ALMX_POL (1 << 7)
610# define MCP794XX_MSK_ALMX_MATCH (MCP794XX_BIT_ALMX_C0 | \
611 MCP794XX_BIT_ALMX_C1 | \
612 MCP794XX_BIT_ALMX_C2)
613
614static irqreturn_t mcp794xx_irq(int irq, void *dev_id)
615{
616 struct i2c_client *client = dev_id;
617 struct ds1307 *ds1307 = i2c_get_clientdata(client);
618 struct mutex *lock = &ds1307->rtc->ops_lock;
619 int reg, ret;
620
621 mutex_lock(lock);
622
623 /* Check and clear alarm 0 interrupt flag. */
624 reg = i2c_smbus_read_byte_data(client, MCP794XX_REG_ALARM0_CTRL);
625 if (reg < 0)
626 goto out;
627 if (!(reg & MCP794XX_BIT_ALMX_IF))
628 goto out;
629 reg &= ~MCP794XX_BIT_ALMX_IF;
630 ret = i2c_smbus_write_byte_data(client, MCP794XX_REG_ALARM0_CTRL, reg);
631 if (ret < 0)
632 goto out;
633
634 /* Disable alarm 0. */
635 reg = i2c_smbus_read_byte_data(client, MCP794XX_REG_CONTROL);
636 if (reg < 0)
637 goto out;
638 reg &= ~MCP794XX_BIT_ALM0_EN;
639 ret = i2c_smbus_write_byte_data(client, MCP794XX_REG_CONTROL, reg);
640 if (ret < 0)
641 goto out;
642
643 rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF);
644
645out:
646 mutex_unlock(lock);
647
648 return IRQ_HANDLED;
649}
650
651static int mcp794xx_read_alarm(struct device *dev, struct rtc_wkalrm *t)
652{
653 struct i2c_client *client = to_i2c_client(dev);
654 struct ds1307 *ds1307 = i2c_get_clientdata(client);
655 u8 *regs = ds1307->regs;
656 int ret;
657
658 if (!test_bit(HAS_ALARM, &ds1307->flags))
659 return -EINVAL;
660
661 /* Read control and alarm 0 registers. */
662 ret = ds1307->read_block_data(client, MCP794XX_REG_CONTROL, 10, regs);
663 if (ret < 0)
664 return ret;
665
666 t->enabled = !!(regs[0] & MCP794XX_BIT_ALM0_EN);
667
668 /* Report alarm 0 time assuming 24-hour and day-of-month modes. */
669 t->time.tm_sec = bcd2bin(ds1307->regs[3] & 0x7f);
670 t->time.tm_min = bcd2bin(ds1307->regs[4] & 0x7f);
671 t->time.tm_hour = bcd2bin(ds1307->regs[5] & 0x3f);
672 t->time.tm_wday = bcd2bin(ds1307->regs[6] & 0x7) - 1;
673 t->time.tm_mday = bcd2bin(ds1307->regs[7] & 0x3f);
674 t->time.tm_mon = bcd2bin(ds1307->regs[8] & 0x1f) - 1;
675 t->time.tm_year = -1;
676 t->time.tm_yday = -1;
677 t->time.tm_isdst = -1;
678
679 dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d "
680 "enabled=%d polarity=%d irq=%d match=%d\n", __func__,
681 t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
682 t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, t->enabled,
683 !!(ds1307->regs[6] & MCP794XX_BIT_ALMX_POL),
684 !!(ds1307->regs[6] & MCP794XX_BIT_ALMX_IF),
685 (ds1307->regs[6] & MCP794XX_MSK_ALMX_MATCH) >> 4);
686
687 return 0;
688}
689
690static int mcp794xx_set_alarm(struct device *dev, struct rtc_wkalrm *t)
691{
692 struct i2c_client *client = to_i2c_client(dev);
693 struct ds1307 *ds1307 = i2c_get_clientdata(client);
694 unsigned char *regs = ds1307->regs;
695 int ret;
696
697 if (!test_bit(HAS_ALARM, &ds1307->flags))
698 return -EINVAL;
699
700 dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d "
701 "enabled=%d pending=%d\n", __func__,
702 t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
703 t->time.tm_wday, t->time.tm_mday, t->time.tm_mon,
704 t->enabled, t->pending);
705
706 /* Read control and alarm 0 registers. */
707 ret = ds1307->read_block_data(client, MCP794XX_REG_CONTROL, 10, regs);
708 if (ret < 0)
709 return ret;
710
711 /* Set alarm 0, using 24-hour and day-of-month modes. */
712 regs[3] = bin2bcd(t->time.tm_sec);
713 regs[4] = bin2bcd(t->time.tm_min);
714 regs[5] = bin2bcd(t->time.tm_hour);
715 regs[6] = bin2bcd(t->time.tm_wday + 1);
716 regs[7] = bin2bcd(t->time.tm_mday);
717 regs[8] = bin2bcd(t->time.tm_mon + 1);
718
719 /* Clear the alarm 0 interrupt flag. */
720 regs[6] &= ~MCP794XX_BIT_ALMX_IF;
721 /* Set alarm match: second, minute, hour, day, date, month. */
722 regs[6] |= MCP794XX_MSK_ALMX_MATCH;
723 /* Disable interrupt. We will not enable until completely programmed */
724 regs[0] &= ~MCP794XX_BIT_ALM0_EN;
725
726 ret = ds1307->write_block_data(client, MCP794XX_REG_CONTROL, 10, regs);
727 if (ret < 0)
728 return ret;
729
730 if (!t->enabled)
731 return 0;
732 regs[0] |= MCP794XX_BIT_ALM0_EN;
733 return i2c_smbus_write_byte_data(client, MCP794XX_REG_CONTROL, regs[0]);
734}
735
736static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled)
737{
738 struct i2c_client *client = to_i2c_client(dev);
739 struct ds1307 *ds1307 = i2c_get_clientdata(client);
740 int reg;
741
742 if (!test_bit(HAS_ALARM, &ds1307->flags))
743 return -EINVAL;
744
745 reg = i2c_smbus_read_byte_data(client, MCP794XX_REG_CONTROL);
746 if (reg < 0)
747 return reg;
748
749 if (enabled)
750 reg |= MCP794XX_BIT_ALM0_EN;
751 else
752 reg &= ~MCP794XX_BIT_ALM0_EN;
753
754 return i2c_smbus_write_byte_data(client, MCP794XX_REG_CONTROL, reg);
755}
756
757static const struct rtc_class_ops mcp794xx_rtc_ops = {
758 .read_time = ds1307_get_time,
759 .set_time = ds1307_set_time,
760 .read_alarm = mcp794xx_read_alarm,
761 .set_alarm = mcp794xx_set_alarm,
762 .alarm_irq_enable = mcp794xx_alarm_irq_enable,
763};
764
765/*----------------------------------------------------------------------*/
766
767static ssize_t
768ds1307_nvram_read(struct file *filp, struct kobject *kobj,
769 struct bin_attribute *attr,
770 char *buf, loff_t off, size_t count)
771{
772 struct i2c_client *client;
773 struct ds1307 *ds1307;
774 int result;
775
776 client = kobj_to_i2c_client(kobj);
777 ds1307 = i2c_get_clientdata(client);
778
779 result = ds1307->read_block_data(client, ds1307->nvram_offset + off,
780 count, buf);
781 if (result < 0)
782 dev_err(&client->dev, "%s error %d\n", "nvram read", result);
783 return result;
784}
785
786static ssize_t
787ds1307_nvram_write(struct file *filp, struct kobject *kobj,
788 struct bin_attribute *attr,
789 char *buf, loff_t off, size_t count)
790{
791 struct i2c_client *client;
792 struct ds1307 *ds1307;
793 int result;
794
795 client = kobj_to_i2c_client(kobj);
796 ds1307 = i2c_get_clientdata(client);
797
798 result = ds1307->write_block_data(client, ds1307->nvram_offset + off,
799 count, buf);
800 if (result < 0) {
801 dev_err(&client->dev, "%s error %d\n", "nvram write", result);
802 return result;
803 }
804 return count;
805}
806
807
808/*----------------------------------------------------------------------*/
809
810static u8 do_trickle_setup_ds1339(struct i2c_client *client,
811 uint32_t ohms, bool diode)
812{
813 u8 setup = (diode) ? DS1307_TRICKLE_CHARGER_DIODE :
814 DS1307_TRICKLE_CHARGER_NO_DIODE;
815
816 switch (ohms) {
817 case 250:
818 setup |= DS1307_TRICKLE_CHARGER_250_OHM;
819 break;
820 case 2000:
821 setup |= DS1307_TRICKLE_CHARGER_2K_OHM;
822 break;
823 case 4000:
824 setup |= DS1307_TRICKLE_CHARGER_4K_OHM;
825 break;
826 default:
827 dev_warn(&client->dev,
828 "Unsupported ohm value %u in dt\n", ohms);
829 return 0;
830 }
831 return setup;
832}
833
834static void ds1307_trickle_of_init(struct i2c_client *client,
835 struct chip_desc *chip)
836{
837 uint32_t ohms = 0;
838 bool diode = true;
839
840 if (!chip->do_trickle_setup)
841 goto out;
842 if (of_property_read_u32(client->dev.of_node, "trickle-resistor-ohms" , &ohms))
843 goto out;
844 if (of_property_read_bool(client->dev.of_node, "trickle-diode-disable"))
845 diode = false;
846 chip->trickle_charger_setup = chip->do_trickle_setup(client,
847 ohms, diode);
848out:
849 return;
850}
851
852/*----------------------------------------------------------------------*/
853
854#ifdef CONFIG_RTC_DRV_DS1307_HWMON
855
856/*
857 * Temperature sensor support for ds3231 devices.
858 */
859
860#define DS3231_REG_TEMPERATURE 0x11
861
862/*
863 * A user-initiated temperature conversion is not started by this function,
864 * so the temperature is updated once every 64 seconds.
865 */
866static int ds3231_hwmon_read_temp(struct device *dev, s32 *mC)
867{
868 struct ds1307 *ds1307 = dev_get_drvdata(dev);
869 u8 temp_buf[2];
870 s16 temp;
871 int ret;
872
873 ret = ds1307->read_block_data(ds1307->client, DS3231_REG_TEMPERATURE,
874 sizeof(temp_buf), temp_buf);
875 if (ret < 0)
876 return ret;
877 if (ret != sizeof(temp_buf))
878 return -EIO;
879
880 /*
881 * Temperature is represented as a 10-bit code with a resolution of
882 * 0.25 degree celsius and encoded in two's complement format.
883 */
884 temp = (temp_buf[0] << 8) | temp_buf[1];
885 temp >>= 6;
886 *mC = temp * 250;
887
888 return 0;
889}
890
891static ssize_t ds3231_hwmon_show_temp(struct device *dev,
892 struct device_attribute *attr, char *buf)
893{
894 int ret;
895 s32 temp;
896
897 ret = ds3231_hwmon_read_temp(dev, &temp);
898 if (ret)
899 return ret;
900
901 return sprintf(buf, "%d\n", temp);
902}
903static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, ds3231_hwmon_show_temp,
904 NULL, 0);
905
906static struct attribute *ds3231_hwmon_attrs[] = {
907 &sensor_dev_attr_temp1_input.dev_attr.attr,
908 NULL,
909};
910ATTRIBUTE_GROUPS(ds3231_hwmon);
911
912static void ds1307_hwmon_register(struct ds1307 *ds1307)
913{
914 struct device *dev;
915
916 if (ds1307->type != ds_3231)
917 return;
918
919 dev = devm_hwmon_device_register_with_groups(&ds1307->client->dev,
920 ds1307->client->name,
921 ds1307, ds3231_hwmon_groups);
922 if (IS_ERR(dev)) {
923 dev_warn(&ds1307->client->dev,
924 "unable to register hwmon device %ld\n", PTR_ERR(dev));
925 }
926}
927
928#else
929
930static void ds1307_hwmon_register(struct ds1307 *ds1307)
931{
932}
933
934#endif /* CONFIG_RTC_DRV_DS1307_HWMON */
935
936/*----------------------------------------------------------------------*/
937
938/*
939 * Square-wave output support for DS3231
940 * Datasheet: https://datasheets.maximintegrated.com/en/ds/DS3231.pdf
941 */
942#ifdef CONFIG_COMMON_CLK
943
944enum {
945 DS3231_CLK_SQW = 0,
946 DS3231_CLK_32KHZ,
947};
948
949#define clk_sqw_to_ds1307(clk) \
950 container_of(clk, struct ds1307, clks[DS3231_CLK_SQW])
951#define clk_32khz_to_ds1307(clk) \
952 container_of(clk, struct ds1307, clks[DS3231_CLK_32KHZ])
953
954static int ds3231_clk_sqw_rates[] = {
955 1,
956 1024,
957 4096,
958 8192,
959};
960
961static int ds1337_write_control(struct ds1307 *ds1307, u8 mask, u8 value)
962{
963 struct i2c_client *client = ds1307->client;
964 struct mutex *lock = &ds1307->rtc->ops_lock;
965 int control;
966 int ret;
967
968 mutex_lock(lock);
969
970 control = i2c_smbus_read_byte_data(client, DS1337_REG_CONTROL);
971 if (control < 0) {
972 ret = control;
973 goto out;
974 }
975
976 control &= ~mask;
977 control |= value;
978
979 ret = i2c_smbus_write_byte_data(client, DS1337_REG_CONTROL, control);
980out:
981 mutex_unlock(lock);
982
983 return ret;
984}
985
986static unsigned long ds3231_clk_sqw_recalc_rate(struct clk_hw *hw,
987 unsigned long parent_rate)
988{
989 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
990 int control;
991 int rate_sel = 0;
992
993 control = i2c_smbus_read_byte_data(ds1307->client, DS1337_REG_CONTROL);
994 if (control < 0)
995 return control;
996 if (control & DS1337_BIT_RS1)
997 rate_sel += 1;
998 if (control & DS1337_BIT_RS2)
999 rate_sel += 2;
1000
1001 return ds3231_clk_sqw_rates[rate_sel];
1002}
1003
1004static long ds3231_clk_sqw_round_rate(struct clk_hw *hw, unsigned long rate,
1005 unsigned long *prate)
1006{
1007 int i;
1008
1009 for (i = ARRAY_SIZE(ds3231_clk_sqw_rates) - 1; i >= 0; i--) {
1010 if (ds3231_clk_sqw_rates[i] <= rate)
1011 return ds3231_clk_sqw_rates[i];
1012 }
1013
1014 return 0;
1015}
1016
1017static int ds3231_clk_sqw_set_rate(struct clk_hw *hw, unsigned long rate,
1018 unsigned long parent_rate)
1019{
1020 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1021 int control = 0;
1022 int rate_sel;
1023
1024 for (rate_sel = 0; rate_sel < ARRAY_SIZE(ds3231_clk_sqw_rates);
1025 rate_sel++) {
1026 if (ds3231_clk_sqw_rates[rate_sel] == rate)
1027 break;
1028 }
1029
1030 if (rate_sel == ARRAY_SIZE(ds3231_clk_sqw_rates))
1031 return -EINVAL;
1032
1033 if (rate_sel & 1)
1034 control |= DS1337_BIT_RS1;
1035 if (rate_sel & 2)
1036 control |= DS1337_BIT_RS2;
1037
1038 return ds1337_write_control(ds1307, DS1337_BIT_RS1 | DS1337_BIT_RS2,
1039 control);
1040}
1041
1042static int ds3231_clk_sqw_prepare(struct clk_hw *hw)
1043{
1044 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1045
1046 return ds1337_write_control(ds1307, DS1337_BIT_INTCN, 0);
1047}
1048
1049static void ds3231_clk_sqw_unprepare(struct clk_hw *hw)
1050{
1051 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1052
1053 ds1337_write_control(ds1307, DS1337_BIT_INTCN, DS1337_BIT_INTCN);
1054}
1055
1056static int ds3231_clk_sqw_is_prepared(struct clk_hw *hw)
1057{
1058 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1059 int control;
1060
1061 control = i2c_smbus_read_byte_data(ds1307->client, DS1337_REG_CONTROL);
1062 if (control < 0)
1063 return control;
1064
1065 return !(control & DS1337_BIT_INTCN);
1066}
1067
1068static const struct clk_ops ds3231_clk_sqw_ops = {
1069 .prepare = ds3231_clk_sqw_prepare,
1070 .unprepare = ds3231_clk_sqw_unprepare,
1071 .is_prepared = ds3231_clk_sqw_is_prepared,
1072 .recalc_rate = ds3231_clk_sqw_recalc_rate,
1073 .round_rate = ds3231_clk_sqw_round_rate,
1074 .set_rate = ds3231_clk_sqw_set_rate,
1075};
1076
1077static unsigned long ds3231_clk_32khz_recalc_rate(struct clk_hw *hw,
1078 unsigned long parent_rate)
1079{
1080 return 32768;
1081}
1082
1083static int ds3231_clk_32khz_control(struct ds1307 *ds1307, bool enable)
1084{
1085 struct i2c_client *client = ds1307->client;
1086 struct mutex *lock = &ds1307->rtc->ops_lock;
1087 int status;
1088 int ret;
1089
1090 mutex_lock(lock);
1091
1092 status = i2c_smbus_read_byte_data(client, DS1337_REG_STATUS);
1093 if (status < 0) {
1094 ret = status;
1095 goto out;
1096 }
1097
1098 if (enable)
1099 status |= DS3231_BIT_EN32KHZ;
1100 else
1101 status &= ~DS3231_BIT_EN32KHZ;
1102
1103 ret = i2c_smbus_write_byte_data(client, DS1337_REG_STATUS, status);
1104out:
1105 mutex_unlock(lock);
1106
1107 return ret;
1108}
1109
1110static int ds3231_clk_32khz_prepare(struct clk_hw *hw)
1111{
1112 struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw);
1113
1114 return ds3231_clk_32khz_control(ds1307, true);
1115}
1116
1117static void ds3231_clk_32khz_unprepare(struct clk_hw *hw)
1118{
1119 struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw);
1120
1121 ds3231_clk_32khz_control(ds1307, false);
1122}
1123
1124static int ds3231_clk_32khz_is_prepared(struct clk_hw *hw)
1125{
1126 struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw);
1127 int status;
1128
1129 status = i2c_smbus_read_byte_data(ds1307->client, DS1337_REG_STATUS);
1130 if (status < 0)
1131 return status;
1132
1133 return !!(status & DS3231_BIT_EN32KHZ);
1134}
1135
1136static const struct clk_ops ds3231_clk_32khz_ops = {
1137 .prepare = ds3231_clk_32khz_prepare,
1138 .unprepare = ds3231_clk_32khz_unprepare,
1139 .is_prepared = ds3231_clk_32khz_is_prepared,
1140 .recalc_rate = ds3231_clk_32khz_recalc_rate,
1141};
1142
1143static struct clk_init_data ds3231_clks_init[] = {
1144 [DS3231_CLK_SQW] = {
1145 .name = "ds3231_clk_sqw",
1146 .ops = &ds3231_clk_sqw_ops,
1147 .flags = CLK_IS_ROOT,
1148 },
1149 [DS3231_CLK_32KHZ] = {
1150 .name = "ds3231_clk_32khz",
1151 .ops = &ds3231_clk_32khz_ops,
1152 .flags = CLK_IS_ROOT,
1153 },
1154};
1155
1156static int ds3231_clks_register(struct ds1307 *ds1307)
1157{
1158 struct i2c_client *client = ds1307->client;
1159 struct device_node *node = client->dev.of_node;
1160 struct clk_onecell_data *onecell;
1161 int i;
1162
1163 onecell = devm_kzalloc(&client->dev, sizeof(*onecell), GFP_KERNEL);
1164 if (!onecell)
1165 return -ENOMEM;
1166
1167 onecell->clk_num = ARRAY_SIZE(ds3231_clks_init);
1168 onecell->clks = devm_kcalloc(&client->dev, onecell->clk_num,
1169 sizeof(onecell->clks[0]), GFP_KERNEL);
1170 if (!onecell->clks)
1171 return -ENOMEM;
1172
1173 for (i = 0; i < ARRAY_SIZE(ds3231_clks_init); i++) {
1174 struct clk_init_data init = ds3231_clks_init[i];
1175
1176 /*
1177 * Interrupt signal due to alarm conditions and square-wave
1178 * output share same pin, so don't initialize both.
1179 */
1180 if (i == DS3231_CLK_SQW && test_bit(HAS_ALARM, &ds1307->flags))
1181 continue;
1182
1183 /* optional override of the clockname */
1184 of_property_read_string_index(node, "clock-output-names", i,
1185 &init.name);
1186 ds1307->clks[i].init = &init;
1187
1188 onecell->clks[i] = devm_clk_register(&client->dev,
1189 &ds1307->clks[i]);
1190 if (IS_ERR(onecell->clks[i]))
1191 return PTR_ERR(onecell->clks[i]);
1192 }
1193
1194 if (!node)
1195 return 0;
1196
1197 of_clk_add_provider(node, of_clk_src_onecell_get, onecell);
1198
1199 return 0;
1200}
1201
1202static void ds1307_clks_register(struct ds1307 *ds1307)
1203{
1204 int ret;
1205
1206 if (ds1307->type != ds_3231)
1207 return;
1208
1209 ret = ds3231_clks_register(ds1307);
1210 if (ret) {
1211 dev_warn(&ds1307->client->dev,
1212 "unable to register clock device %d\n", ret);
1213 }
1214}
1215
1216#else
1217
1218static void ds1307_clks_register(struct ds1307 *ds1307)
1219{
1220}
1221
1222#endif /* CONFIG_COMMON_CLK */
1223
1224static int ds1307_probe(struct i2c_client *client,
1225 const struct i2c_device_id *id)
1226{
1227 struct ds1307 *ds1307;
1228 int err = -ENODEV;
1229 int tmp;
1230 struct chip_desc *chip = &chips[id->driver_data];
1231 struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
1232 bool want_irq = false;
1233 bool ds1307_can_wakeup_device = false;
1234 unsigned char *buf;
1235 struct ds1307_platform_data *pdata = dev_get_platdata(&client->dev);
1236 irq_handler_t irq_handler = ds1307_irq;
1237
1238 static const int bbsqi_bitpos[] = {
1239 [ds_1337] = 0,
1240 [ds_1339] = DS1339_BIT_BBSQI,
1241 [ds_3231] = DS3231_BIT_BBSQW,
1242 };
1243 const struct rtc_class_ops *rtc_ops = &ds13xx_rtc_ops;
1244
1245 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)
1246 && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_I2C_BLOCK))
1247 return -EIO;
1248
1249 ds1307 = devm_kzalloc(&client->dev, sizeof(struct ds1307), GFP_KERNEL);
1250 if (!ds1307)
1251 return -ENOMEM;
1252
1253 i2c_set_clientdata(client, ds1307);
1254
1255 ds1307->client = client;
1256 ds1307->type = id->driver_data;
1257
1258 if (!pdata && client->dev.of_node)
1259 ds1307_trickle_of_init(client, chip);
1260 else if (pdata && pdata->trickle_charger_setup)
1261 chip->trickle_charger_setup = pdata->trickle_charger_setup;
1262
1263 if (chip->trickle_charger_setup && chip->trickle_charger_reg) {
1264 dev_dbg(&client->dev, "writing trickle charger info 0x%x to 0x%x\n",
1265 DS13XX_TRICKLE_CHARGER_MAGIC | chip->trickle_charger_setup,
1266 chip->trickle_charger_reg);
1267 i2c_smbus_write_byte_data(client, chip->trickle_charger_reg,
1268 DS13XX_TRICKLE_CHARGER_MAGIC |
1269 chip->trickle_charger_setup);
1270 }
1271
1272 buf = ds1307->regs;
1273 if (i2c_check_functionality(adapter, I2C_FUNC_SMBUS_I2C_BLOCK)) {
1274 ds1307->read_block_data = ds1307_native_smbus_read_block_data;
1275 ds1307->write_block_data = ds1307_native_smbus_write_block_data;
1276 } else {
1277 ds1307->read_block_data = ds1307_read_block_data;
1278 ds1307->write_block_data = ds1307_write_block_data;
1279 }
1280
1281#ifdef CONFIG_OF
1282/*
1283 * For devices with no IRQ directly connected to the SoC, the RTC chip
1284 * can be forced as a wakeup source by stating that explicitly in
1285 * the device's .dts file using the "wakeup-source" boolean property.
1286 * If the "wakeup-source" property is set, don't request an IRQ.
1287 * This will guarantee the 'wakealarm' sysfs entry is available on the device,
1288 * if supported by the RTC.
1289 */
1290 if (of_property_read_bool(client->dev.of_node, "wakeup-source")) {
1291 ds1307_can_wakeup_device = true;
1292 }
1293#endif
1294
1295 switch (ds1307->type) {
1296 case ds_1337:
1297 case ds_1339:
1298 case ds_3231:
1299 /* get registers that the "rtc" read below won't read... */
1300 tmp = ds1307->read_block_data(ds1307->client,
1301 DS1337_REG_CONTROL, 2, buf);
1302 if (tmp != 2) {
1303 dev_dbg(&client->dev, "read error %d\n", tmp);
1304 err = -EIO;
1305 goto exit;
1306 }
1307
1308 /* oscillator off? turn it on, so clock can tick. */
1309 if (ds1307->regs[0] & DS1337_BIT_nEOSC)
1310 ds1307->regs[0] &= ~DS1337_BIT_nEOSC;
1311
1312 /*
1313 * Using IRQ or defined as wakeup-source?
1314 * Disable the square wave and both alarms.
1315 * For some variants, be sure alarms can trigger when we're
1316 * running on Vbackup (BBSQI/BBSQW)
1317 */
1318 if (chip->alarm && (ds1307->client->irq > 0 ||
1319 ds1307_can_wakeup_device)) {
1320 ds1307->regs[0] |= DS1337_BIT_INTCN
1321 | bbsqi_bitpos[ds1307->type];
1322 ds1307->regs[0] &= ~(DS1337_BIT_A2IE | DS1337_BIT_A1IE);
1323
1324 want_irq = true;
1325 }
1326
1327 i2c_smbus_write_byte_data(client, DS1337_REG_CONTROL,
1328 ds1307->regs[0]);
1329
1330 /* oscillator fault? clear flag, and warn */
1331 if (ds1307->regs[1] & DS1337_BIT_OSF) {
1332 i2c_smbus_write_byte_data(client, DS1337_REG_STATUS,
1333 ds1307->regs[1] & ~DS1337_BIT_OSF);
1334 dev_warn(&client->dev, "SET TIME!\n");
1335 }
1336 break;
1337
1338 case rx_8025:
1339 tmp = i2c_smbus_read_i2c_block_data(ds1307->client,
1340 RX8025_REG_CTRL1 << 4 | 0x08, 2, buf);
1341 if (tmp != 2) {
1342 dev_dbg(&client->dev, "read error %d\n", tmp);
1343 err = -EIO;
1344 goto exit;
1345 }
1346
1347 /* oscillator off? turn it on, so clock can tick. */
1348 if (!(ds1307->regs[1] & RX8025_BIT_XST)) {
1349 ds1307->regs[1] |= RX8025_BIT_XST;
1350 i2c_smbus_write_byte_data(client,
1351 RX8025_REG_CTRL2 << 4 | 0x08,
1352 ds1307->regs[1]);
1353 dev_warn(&client->dev,
1354 "oscillator stop detected - SET TIME!\n");
1355 }
1356
1357 if (ds1307->regs[1] & RX8025_BIT_PON) {
1358 ds1307->regs[1] &= ~RX8025_BIT_PON;
1359 i2c_smbus_write_byte_data(client,
1360 RX8025_REG_CTRL2 << 4 | 0x08,
1361 ds1307->regs[1]);
1362 dev_warn(&client->dev, "power-on detected\n");
1363 }
1364
1365 if (ds1307->regs[1] & RX8025_BIT_VDET) {
1366 ds1307->regs[1] &= ~RX8025_BIT_VDET;
1367 i2c_smbus_write_byte_data(client,
1368 RX8025_REG_CTRL2 << 4 | 0x08,
1369 ds1307->regs[1]);
1370 dev_warn(&client->dev, "voltage drop detected\n");
1371 }
1372
1373 /* make sure we are running in 24hour mode */
1374 if (!(ds1307->regs[0] & RX8025_BIT_2412)) {
1375 u8 hour;
1376
1377 /* switch to 24 hour mode */
1378 i2c_smbus_write_byte_data(client,
1379 RX8025_REG_CTRL1 << 4 | 0x08,
1380 ds1307->regs[0] |
1381 RX8025_BIT_2412);
1382
1383 tmp = i2c_smbus_read_i2c_block_data(ds1307->client,
1384 RX8025_REG_CTRL1 << 4 | 0x08, 2, buf);
1385 if (tmp != 2) {
1386 dev_dbg(&client->dev, "read error %d\n", tmp);
1387 err = -EIO;
1388 goto exit;
1389 }
1390
1391 /* correct hour */
1392 hour = bcd2bin(ds1307->regs[DS1307_REG_HOUR]);
1393 if (hour == 12)
1394 hour = 0;
1395 if (ds1307->regs[DS1307_REG_HOUR] & DS1307_BIT_PM)
1396 hour += 12;
1397
1398 i2c_smbus_write_byte_data(client,
1399 DS1307_REG_HOUR << 4 | 0x08,
1400 hour);
1401 }
1402 break;
1403 case ds_1388:
1404 ds1307->offset = 1; /* Seconds starts at 1 */
1405 break;
1406 case mcp794xx:
1407 rtc_ops = &mcp794xx_rtc_ops;
1408 if (ds1307->client->irq > 0 && chip->alarm) {
1409 irq_handler = mcp794xx_irq;
1410 want_irq = true;
1411 }
1412 break;
1413 default:
1414 break;
1415 }
1416
1417read_rtc:
1418 /* read RTC registers */
1419 tmp = ds1307->read_block_data(ds1307->client, ds1307->offset, 8, buf);
1420 if (tmp != 8) {
1421 dev_dbg(&client->dev, "read error %d\n", tmp);
1422 err = -EIO;
1423 goto exit;
1424 }
1425
1426 /*
1427 * minimal sanity checking; some chips (like DS1340) don't
1428 * specify the extra bits as must-be-zero, but there are
1429 * still a few values that are clearly out-of-range.
1430 */
1431 tmp = ds1307->regs[DS1307_REG_SECS];
1432 switch (ds1307->type) {
1433 case ds_1307:
1434 case m41t00:
1435 /* clock halted? turn it on, so clock can tick. */
1436 if (tmp & DS1307_BIT_CH) {
1437 i2c_smbus_write_byte_data(client, DS1307_REG_SECS, 0);
1438 dev_warn(&client->dev, "SET TIME!\n");
1439 goto read_rtc;
1440 }
1441 break;
1442 case ds_1338:
1443 /* clock halted? turn it on, so clock can tick. */
1444 if (tmp & DS1307_BIT_CH)
1445 i2c_smbus_write_byte_data(client, DS1307_REG_SECS, 0);
1446
1447 /* oscillator fault? clear flag, and warn */
1448 if (ds1307->regs[DS1307_REG_CONTROL] & DS1338_BIT_OSF) {
1449 i2c_smbus_write_byte_data(client, DS1307_REG_CONTROL,
1450 ds1307->regs[DS1307_REG_CONTROL]
1451 & ~DS1338_BIT_OSF);
1452 dev_warn(&client->dev, "SET TIME!\n");
1453 goto read_rtc;
1454 }
1455 break;
1456 case ds_1340:
1457 /* clock halted? turn it on, so clock can tick. */
1458 if (tmp & DS1340_BIT_nEOSC)
1459 i2c_smbus_write_byte_data(client, DS1307_REG_SECS, 0);
1460
1461 tmp = i2c_smbus_read_byte_data(client, DS1340_REG_FLAG);
1462 if (tmp < 0) {
1463 dev_dbg(&client->dev, "read error %d\n", tmp);
1464 err = -EIO;
1465 goto exit;
1466 }
1467
1468 /* oscillator fault? clear flag, and warn */
1469 if (tmp & DS1340_BIT_OSF) {
1470 i2c_smbus_write_byte_data(client, DS1340_REG_FLAG, 0);
1471 dev_warn(&client->dev, "SET TIME!\n");
1472 }
1473 break;
1474 case mcp794xx:
1475 /* make sure that the backup battery is enabled */
1476 if (!(ds1307->regs[DS1307_REG_WDAY] & MCP794XX_BIT_VBATEN)) {
1477 i2c_smbus_write_byte_data(client, DS1307_REG_WDAY,
1478 ds1307->regs[DS1307_REG_WDAY]
1479 | MCP794XX_BIT_VBATEN);
1480 }
1481
1482 /* clock halted? turn it on, so clock can tick. */
1483 if (!(tmp & MCP794XX_BIT_ST)) {
1484 i2c_smbus_write_byte_data(client, DS1307_REG_SECS,
1485 MCP794XX_BIT_ST);
1486 dev_warn(&client->dev, "SET TIME!\n");
1487 goto read_rtc;
1488 }
1489
1490 break;
1491 default:
1492 break;
1493 }
1494
1495 tmp = ds1307->regs[DS1307_REG_HOUR];
1496 switch (ds1307->type) {
1497 case ds_1340:
1498 case m41t00:
1499 /*
1500 * NOTE: ignores century bits; fix before deploying
1501 * systems that will run through year 2100.
1502 */
1503 break;
1504 case rx_8025:
1505 break;
1506 default:
1507 if (!(tmp & DS1307_BIT_12HR))
1508 break;
1509
1510 /*
1511 * Be sure we're in 24 hour mode. Multi-master systems
1512 * take note...
1513 */
1514 tmp = bcd2bin(tmp & 0x1f);
1515 if (tmp == 12)
1516 tmp = 0;
1517 if (ds1307->regs[DS1307_REG_HOUR] & DS1307_BIT_PM)
1518 tmp += 12;
1519 i2c_smbus_write_byte_data(client,
1520 ds1307->offset + DS1307_REG_HOUR,
1521 bin2bcd(tmp));
1522 }
1523
1524 if (want_irq) {
1525 device_set_wakeup_capable(&client->dev, true);
1526 set_bit(HAS_ALARM, &ds1307->flags);
1527 }
1528 ds1307->rtc = devm_rtc_device_register(&client->dev, client->name,
1529 rtc_ops, THIS_MODULE);
1530 if (IS_ERR(ds1307->rtc)) {
1531 return PTR_ERR(ds1307->rtc);
1532 }
1533
1534 if (ds1307_can_wakeup_device && ds1307->client->irq <= 0) {
1535 /* Disable request for an IRQ */
1536 want_irq = false;
1537 dev_info(&client->dev, "'wakeup-source' is set, request for an IRQ is disabled!\n");
1538 /* We cannot support UIE mode if we do not have an IRQ line */
1539 ds1307->rtc->uie_unsupported = 1;
1540 }
1541
1542 if (want_irq) {
1543 err = devm_request_threaded_irq(&client->dev,
1544 client->irq, NULL, irq_handler,
1545 IRQF_SHARED | IRQF_ONESHOT,
1546 ds1307->rtc->name, client);
1547 if (err) {
1548 client->irq = 0;
1549 device_set_wakeup_capable(&client->dev, false);
1550 clear_bit(HAS_ALARM, &ds1307->flags);
1551 dev_err(&client->dev, "unable to request IRQ!\n");
1552 } else
1553 dev_dbg(&client->dev, "got IRQ %d\n", client->irq);
1554 }
1555
1556 if (chip->nvram_size) {
1557
1558 ds1307->nvram = devm_kzalloc(&client->dev,
1559 sizeof(struct bin_attribute),
1560 GFP_KERNEL);
1561 if (!ds1307->nvram) {
1562 dev_err(&client->dev, "cannot allocate memory for nvram sysfs\n");
1563 } else {
1564
1565 ds1307->nvram->attr.name = "nvram";
1566 ds1307->nvram->attr.mode = S_IRUGO | S_IWUSR;
1567
1568 sysfs_bin_attr_init(ds1307->nvram);
1569
1570 ds1307->nvram->read = ds1307_nvram_read;
1571 ds1307->nvram->write = ds1307_nvram_write;
1572 ds1307->nvram->size = chip->nvram_size;
1573 ds1307->nvram_offset = chip->nvram_offset;
1574
1575 err = sysfs_create_bin_file(&client->dev.kobj,
1576 ds1307->nvram);
1577 if (err) {
1578 dev_err(&client->dev,
1579 "unable to create sysfs file: %s\n",
1580 ds1307->nvram->attr.name);
1581 } else {
1582 set_bit(HAS_NVRAM, &ds1307->flags);
1583 dev_info(&client->dev, "%zu bytes nvram\n",
1584 ds1307->nvram->size);
1585 }
1586 }
1587 }
1588
1589 ds1307_hwmon_register(ds1307);
1590 ds1307_clks_register(ds1307);
1591
1592 return 0;
1593
1594exit:
1595 return err;
1596}
1597
1598static int ds1307_remove(struct i2c_client *client)
1599{
1600 struct ds1307 *ds1307 = i2c_get_clientdata(client);
1601
1602 if (test_and_clear_bit(HAS_NVRAM, &ds1307->flags))
1603 sysfs_remove_bin_file(&client->dev.kobj, ds1307->nvram);
1604
1605 return 0;
1606}
1607
1608static struct i2c_driver ds1307_driver = {
1609 .driver = {
1610 .name = "rtc-ds1307",
1611 },
1612 .probe = ds1307_probe,
1613 .remove = ds1307_remove,
1614 .id_table = ds1307_id,
1615};
1616
1617module_i2c_driver(ds1307_driver);
1618
1619MODULE_DESCRIPTION("RTC driver for DS1307 and similar chips");
1620MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * rtc-ds1307.c - RTC driver for some mostly-compatible I2C chips.
4 *
5 * Copyright (C) 2005 James Chapman (ds1337 core)
6 * Copyright (C) 2006 David Brownell
7 * Copyright (C) 2009 Matthias Fuchs (rx8025 support)
8 * Copyright (C) 2012 Bertrand Achard (nvram access fixes)
9 */
10
11#include <linux/bcd.h>
12#include <linux/i2c.h>
13#include <linux/init.h>
14#include <linux/kstrtox.h>
15#include <linux/mod_devicetable.h>
16#include <linux/module.h>
17#include <linux/property.h>
18#include <linux/rtc/ds1307.h>
19#include <linux/rtc.h>
20#include <linux/slab.h>
21#include <linux/string.h>
22#include <linux/hwmon.h>
23#include <linux/hwmon-sysfs.h>
24#include <linux/clk-provider.h>
25#include <linux/regmap.h>
26#include <linux/watchdog.h>
27
28/*
29 * We can't determine type by probing, but if we expect pre-Linux code
30 * to have set the chip up as a clock (turning on the oscillator and
31 * setting the date and time), Linux can ignore the non-clock features.
32 * That's a natural job for a factory or repair bench.
33 */
34enum ds_type {
35 unknown_ds_type, /* always first and 0 */
36 ds_1307,
37 ds_1308,
38 ds_1337,
39 ds_1338,
40 ds_1339,
41 ds_1340,
42 ds_1341,
43 ds_1388,
44 ds_3231,
45 m41t0,
46 m41t00,
47 m41t11,
48 mcp794xx,
49 rx_8025,
50 rx_8130,
51 last_ds_type /* always last */
52 /* rs5c372 too? different address... */
53};
54
55/* RTC registers don't differ much, except for the century flag */
56#define DS1307_REG_SECS 0x00 /* 00-59 */
57# define DS1307_BIT_CH 0x80
58# define DS1340_BIT_nEOSC 0x80
59# define MCP794XX_BIT_ST 0x80
60#define DS1307_REG_MIN 0x01 /* 00-59 */
61# define M41T0_BIT_OF 0x80
62#define DS1307_REG_HOUR 0x02 /* 00-23, or 1-12{am,pm} */
63# define DS1307_BIT_12HR 0x40 /* in REG_HOUR */
64# define DS1307_BIT_PM 0x20 /* in REG_HOUR */
65# define DS1340_BIT_CENTURY_EN 0x80 /* in REG_HOUR */
66# define DS1340_BIT_CENTURY 0x40 /* in REG_HOUR */
67#define DS1307_REG_WDAY 0x03 /* 01-07 */
68# define MCP794XX_BIT_OSCRUN BIT(5)
69# define MCP794XX_BIT_VBATEN 0x08
70#define DS1307_REG_MDAY 0x04 /* 01-31 */
71#define DS1307_REG_MONTH 0x05 /* 01-12 */
72# define DS1337_BIT_CENTURY 0x80 /* in REG_MONTH */
73#define DS1307_REG_YEAR 0x06 /* 00-99 */
74
75/*
76 * Other registers (control, status, alarms, trickle charge, NVRAM, etc)
77 * start at 7, and they differ a LOT. Only control and status matter for
78 * basic RTC date and time functionality; be careful using them.
79 */
80#define DS1307_REG_CONTROL 0x07 /* or ds1338 */
81# define DS1307_BIT_OUT 0x80
82# define DS1338_BIT_OSF 0x20
83# define DS1307_BIT_SQWE 0x10
84# define DS1307_BIT_RS1 0x02
85# define DS1307_BIT_RS0 0x01
86#define DS1337_REG_CONTROL 0x0e
87# define DS1337_BIT_nEOSC 0x80
88# define DS1339_BIT_BBSQI 0x20
89# define DS3231_BIT_BBSQW 0x40 /* same as BBSQI */
90# define DS1337_BIT_RS2 0x10
91# define DS1337_BIT_RS1 0x08
92# define DS1337_BIT_INTCN 0x04
93# define DS1337_BIT_A2IE 0x02
94# define DS1337_BIT_A1IE 0x01
95#define DS1340_REG_CONTROL 0x07
96# define DS1340_BIT_OUT 0x80
97# define DS1340_BIT_FT 0x40
98# define DS1340_BIT_CALIB_SIGN 0x20
99# define DS1340_M_CALIBRATION 0x1f
100#define DS1340_REG_FLAG 0x09
101# define DS1340_BIT_OSF 0x80
102#define DS1337_REG_STATUS 0x0f
103# define DS1337_BIT_OSF 0x80
104# define DS3231_BIT_EN32KHZ 0x08
105# define DS1337_BIT_A2I 0x02
106# define DS1337_BIT_A1I 0x01
107#define DS1339_REG_ALARM1_SECS 0x07
108
109#define DS13XX_TRICKLE_CHARGER_MAGIC 0xa0
110
111#define RX8025_REG_CTRL1 0x0e
112# define RX8025_BIT_2412 0x20
113#define RX8025_REG_CTRL2 0x0f
114# define RX8025_BIT_PON 0x10
115# define RX8025_BIT_VDET 0x40
116# define RX8025_BIT_XST 0x20
117
118#define RX8130_REG_ALARM_MIN 0x17
119#define RX8130_REG_ALARM_HOUR 0x18
120#define RX8130_REG_ALARM_WEEK_OR_DAY 0x19
121#define RX8130_REG_EXTENSION 0x1c
122#define RX8130_REG_EXTENSION_WADA BIT(3)
123#define RX8130_REG_FLAG 0x1d
124#define RX8130_REG_FLAG_VLF BIT(1)
125#define RX8130_REG_FLAG_AF BIT(3)
126#define RX8130_REG_CONTROL0 0x1e
127#define RX8130_REG_CONTROL0_AIE BIT(3)
128#define RX8130_REG_CONTROL1 0x1f
129#define RX8130_REG_CONTROL1_INIEN BIT(4)
130#define RX8130_REG_CONTROL1_CHGEN BIT(5)
131
132#define MCP794XX_REG_CONTROL 0x07
133# define MCP794XX_BIT_ALM0_EN 0x10
134# define MCP794XX_BIT_ALM1_EN 0x20
135#define MCP794XX_REG_ALARM0_BASE 0x0a
136#define MCP794XX_REG_ALARM0_CTRL 0x0d
137#define MCP794XX_REG_ALARM1_BASE 0x11
138#define MCP794XX_REG_ALARM1_CTRL 0x14
139# define MCP794XX_BIT_ALMX_IF BIT(3)
140# define MCP794XX_BIT_ALMX_C0 BIT(4)
141# define MCP794XX_BIT_ALMX_C1 BIT(5)
142# define MCP794XX_BIT_ALMX_C2 BIT(6)
143# define MCP794XX_BIT_ALMX_POL BIT(7)
144# define MCP794XX_MSK_ALMX_MATCH (MCP794XX_BIT_ALMX_C0 | \
145 MCP794XX_BIT_ALMX_C1 | \
146 MCP794XX_BIT_ALMX_C2)
147
148#define M41TXX_REG_CONTROL 0x07
149# define M41TXX_BIT_OUT BIT(7)
150# define M41TXX_BIT_FT BIT(6)
151# define M41TXX_BIT_CALIB_SIGN BIT(5)
152# define M41TXX_M_CALIBRATION GENMASK(4, 0)
153
154#define DS1388_REG_WDOG_HUN_SECS 0x08
155#define DS1388_REG_WDOG_SECS 0x09
156#define DS1388_REG_FLAG 0x0b
157# define DS1388_BIT_WF BIT(6)
158# define DS1388_BIT_OSF BIT(7)
159#define DS1388_REG_CONTROL 0x0c
160# define DS1388_BIT_RST BIT(0)
161# define DS1388_BIT_WDE BIT(1)
162# define DS1388_BIT_nEOSC BIT(7)
163
164/* negative offset step is -2.034ppm */
165#define M41TXX_NEG_OFFSET_STEP_PPB 2034
166/* positive offset step is +4.068ppm */
167#define M41TXX_POS_OFFSET_STEP_PPB 4068
168/* Min and max values supported with 'offset' interface by M41TXX */
169#define M41TXX_MIN_OFFSET ((-31) * M41TXX_NEG_OFFSET_STEP_PPB)
170#define M41TXX_MAX_OFFSET ((31) * M41TXX_POS_OFFSET_STEP_PPB)
171
172struct ds1307 {
173 enum ds_type type;
174 struct device *dev;
175 struct regmap *regmap;
176 const char *name;
177 struct rtc_device *rtc;
178#ifdef CONFIG_COMMON_CLK
179 struct clk_hw clks[2];
180#endif
181};
182
183struct chip_desc {
184 unsigned alarm:1;
185 u16 nvram_offset;
186 u16 nvram_size;
187 u8 offset; /* register's offset */
188 u8 century_reg;
189 u8 century_enable_bit;
190 u8 century_bit;
191 u8 bbsqi_bit;
192 irq_handler_t irq_handler;
193 const struct rtc_class_ops *rtc_ops;
194 u16 trickle_charger_reg;
195 u8 (*do_trickle_setup)(struct ds1307 *, u32,
196 bool);
197 /* Does the RTC require trickle-resistor-ohms to select the value of
198 * the resistor between Vcc and Vbackup?
199 */
200 bool requires_trickle_resistor;
201 /* Some RTC's batteries and supercaps were charged by default, others
202 * allow charging but were not configured previously to do so.
203 * Remember this behavior to stay backwards compatible.
204 */
205 bool charge_default;
206};
207
208static const struct chip_desc chips[last_ds_type];
209
210static int ds1307_get_time(struct device *dev, struct rtc_time *t)
211{
212 struct ds1307 *ds1307 = dev_get_drvdata(dev);
213 int tmp, ret;
214 const struct chip_desc *chip = &chips[ds1307->type];
215 u8 regs[7];
216
217 if (ds1307->type == rx_8130) {
218 unsigned int regflag;
219 ret = regmap_read(ds1307->regmap, RX8130_REG_FLAG, ®flag);
220 if (ret) {
221 dev_err(dev, "%s error %d\n", "read", ret);
222 return ret;
223 }
224
225 if (regflag & RX8130_REG_FLAG_VLF) {
226 dev_warn_once(dev, "oscillator failed, set time!\n");
227 return -EINVAL;
228 }
229 }
230
231 /* read the RTC date and time registers all at once */
232 ret = regmap_bulk_read(ds1307->regmap, chip->offset, regs,
233 sizeof(regs));
234 if (ret) {
235 dev_err(dev, "%s error %d\n", "read", ret);
236 return ret;
237 }
238
239 dev_dbg(dev, "%s: %7ph\n", "read", regs);
240
241 /* if oscillator fail bit is set, no data can be trusted */
242 if (ds1307->type == m41t0 &&
243 regs[DS1307_REG_MIN] & M41T0_BIT_OF) {
244 dev_warn_once(dev, "oscillator failed, set time!\n");
245 return -EINVAL;
246 } else if (ds1307->type == mcp794xx &&
247 !(regs[DS1307_REG_WDAY] & MCP794XX_BIT_OSCRUN)) {
248 dev_warn_once(dev, "oscillator failed, set time!\n");
249 return -EINVAL;
250 }
251
252 tmp = regs[DS1307_REG_SECS];
253 switch (ds1307->type) {
254 case ds_1307:
255 case m41t0:
256 case m41t00:
257 case m41t11:
258 if (tmp & DS1307_BIT_CH)
259 return -EINVAL;
260 break;
261 case ds_1308:
262 case ds_1338:
263 if (tmp & DS1307_BIT_CH)
264 return -EINVAL;
265
266 ret = regmap_read(ds1307->regmap, DS1307_REG_CONTROL, &tmp);
267 if (ret)
268 return ret;
269 if (tmp & DS1338_BIT_OSF)
270 return -EINVAL;
271 break;
272 case ds_1340:
273 if (tmp & DS1340_BIT_nEOSC)
274 return -EINVAL;
275
276 ret = regmap_read(ds1307->regmap, DS1340_REG_FLAG, &tmp);
277 if (ret)
278 return ret;
279 if (tmp & DS1340_BIT_OSF)
280 return -EINVAL;
281 break;
282 case ds_1388:
283 ret = regmap_read(ds1307->regmap, DS1388_REG_FLAG, &tmp);
284 if (ret)
285 return ret;
286 if (tmp & DS1388_BIT_OSF)
287 return -EINVAL;
288 break;
289 case mcp794xx:
290 if (!(tmp & MCP794XX_BIT_ST))
291 return -EINVAL;
292
293 break;
294 default:
295 break;
296 }
297
298 t->tm_sec = bcd2bin(regs[DS1307_REG_SECS] & 0x7f);
299 t->tm_min = bcd2bin(regs[DS1307_REG_MIN] & 0x7f);
300 tmp = regs[DS1307_REG_HOUR] & 0x3f;
301 t->tm_hour = bcd2bin(tmp);
302 /* rx8130 is bit position, not BCD */
303 if (ds1307->type == rx_8130)
304 t->tm_wday = fls(regs[DS1307_REG_WDAY] & 0x7f);
305 else
306 t->tm_wday = bcd2bin(regs[DS1307_REG_WDAY] & 0x07) - 1;
307 t->tm_mday = bcd2bin(regs[DS1307_REG_MDAY] & 0x3f);
308 tmp = regs[DS1307_REG_MONTH] & 0x1f;
309 t->tm_mon = bcd2bin(tmp) - 1;
310 t->tm_year = bcd2bin(regs[DS1307_REG_YEAR]) + 100;
311
312 if (regs[chip->century_reg] & chip->century_bit &&
313 IS_ENABLED(CONFIG_RTC_DRV_DS1307_CENTURY))
314 t->tm_year += 100;
315
316 dev_dbg(dev, "%s secs=%d, mins=%d, "
317 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n",
318 "read", t->tm_sec, t->tm_min,
319 t->tm_hour, t->tm_mday,
320 t->tm_mon, t->tm_year, t->tm_wday);
321
322 return 0;
323}
324
325static int ds1307_set_time(struct device *dev, struct rtc_time *t)
326{
327 struct ds1307 *ds1307 = dev_get_drvdata(dev);
328 const struct chip_desc *chip = &chips[ds1307->type];
329 int result;
330 int tmp;
331 u8 regs[7];
332
333 dev_dbg(dev, "%s secs=%d, mins=%d, "
334 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n",
335 "write", t->tm_sec, t->tm_min,
336 t->tm_hour, t->tm_mday,
337 t->tm_mon, t->tm_year, t->tm_wday);
338
339 if (t->tm_year < 100)
340 return -EINVAL;
341
342#ifdef CONFIG_RTC_DRV_DS1307_CENTURY
343 if (t->tm_year > (chip->century_bit ? 299 : 199))
344 return -EINVAL;
345#else
346 if (t->tm_year > 199)
347 return -EINVAL;
348#endif
349
350 regs[DS1307_REG_SECS] = bin2bcd(t->tm_sec);
351 regs[DS1307_REG_MIN] = bin2bcd(t->tm_min);
352 regs[DS1307_REG_HOUR] = bin2bcd(t->tm_hour);
353 /* rx8130 is bit position, not BCD */
354 if (ds1307->type == rx_8130)
355 regs[DS1307_REG_WDAY] = 1 << t->tm_wday;
356 else
357 regs[DS1307_REG_WDAY] = bin2bcd(t->tm_wday + 1);
358 regs[DS1307_REG_MDAY] = bin2bcd(t->tm_mday);
359 regs[DS1307_REG_MONTH] = bin2bcd(t->tm_mon + 1);
360
361 /* assume 20YY not 19YY */
362 tmp = t->tm_year % 100;
363 regs[DS1307_REG_YEAR] = bin2bcd(tmp);
364
365 if (chip->century_enable_bit)
366 regs[chip->century_reg] |= chip->century_enable_bit;
367 if (t->tm_year > 199 && chip->century_bit)
368 regs[chip->century_reg] |= chip->century_bit;
369
370 switch (ds1307->type) {
371 case ds_1308:
372 case ds_1338:
373 regmap_update_bits(ds1307->regmap, DS1307_REG_CONTROL,
374 DS1338_BIT_OSF, 0);
375 break;
376 case ds_1340:
377 regmap_update_bits(ds1307->regmap, DS1340_REG_FLAG,
378 DS1340_BIT_OSF, 0);
379 break;
380 case ds_1388:
381 regmap_update_bits(ds1307->regmap, DS1388_REG_FLAG,
382 DS1388_BIT_OSF, 0);
383 break;
384 case mcp794xx:
385 /*
386 * these bits were cleared when preparing the date/time
387 * values and need to be set again before writing the
388 * regsfer out to the device.
389 */
390 regs[DS1307_REG_SECS] |= MCP794XX_BIT_ST;
391 regs[DS1307_REG_WDAY] |= MCP794XX_BIT_VBATEN;
392 break;
393 default:
394 break;
395 }
396
397 dev_dbg(dev, "%s: %7ph\n", "write", regs);
398
399 result = regmap_bulk_write(ds1307->regmap, chip->offset, regs,
400 sizeof(regs));
401 if (result) {
402 dev_err(dev, "%s error %d\n", "write", result);
403 return result;
404 }
405
406 if (ds1307->type == rx_8130) {
407 /* clear Voltage Loss Flag as data is available now */
408 result = regmap_write(ds1307->regmap, RX8130_REG_FLAG,
409 ~(u8)RX8130_REG_FLAG_VLF);
410 if (result) {
411 dev_err(dev, "%s error %d\n", "write", result);
412 return result;
413 }
414 }
415
416 return 0;
417}
418
419static int ds1337_read_alarm(struct device *dev, struct rtc_wkalrm *t)
420{
421 struct ds1307 *ds1307 = dev_get_drvdata(dev);
422 int ret;
423 u8 regs[9];
424
425 /* read all ALARM1, ALARM2, and status registers at once */
426 ret = regmap_bulk_read(ds1307->regmap, DS1339_REG_ALARM1_SECS,
427 regs, sizeof(regs));
428 if (ret) {
429 dev_err(dev, "%s error %d\n", "alarm read", ret);
430 return ret;
431 }
432
433 dev_dbg(dev, "%s: %4ph, %3ph, %2ph\n", "alarm read",
434 ®s[0], ®s[4], ®s[7]);
435
436 /*
437 * report alarm time (ALARM1); assume 24 hour and day-of-month modes,
438 * and that all four fields are checked matches
439 */
440 t->time.tm_sec = bcd2bin(regs[0] & 0x7f);
441 t->time.tm_min = bcd2bin(regs[1] & 0x7f);
442 t->time.tm_hour = bcd2bin(regs[2] & 0x3f);
443 t->time.tm_mday = bcd2bin(regs[3] & 0x3f);
444
445 /* ... and status */
446 t->enabled = !!(regs[7] & DS1337_BIT_A1IE);
447 t->pending = !!(regs[8] & DS1337_BIT_A1I);
448
449 dev_dbg(dev, "%s secs=%d, mins=%d, "
450 "hours=%d, mday=%d, enabled=%d, pending=%d\n",
451 "alarm read", t->time.tm_sec, t->time.tm_min,
452 t->time.tm_hour, t->time.tm_mday,
453 t->enabled, t->pending);
454
455 return 0;
456}
457
458static int ds1337_set_alarm(struct device *dev, struct rtc_wkalrm *t)
459{
460 struct ds1307 *ds1307 = dev_get_drvdata(dev);
461 unsigned char regs[9];
462 u8 control, status;
463 int ret;
464
465 dev_dbg(dev, "%s secs=%d, mins=%d, "
466 "hours=%d, mday=%d, enabled=%d, pending=%d\n",
467 "alarm set", t->time.tm_sec, t->time.tm_min,
468 t->time.tm_hour, t->time.tm_mday,
469 t->enabled, t->pending);
470
471 /* read current status of both alarms and the chip */
472 ret = regmap_bulk_read(ds1307->regmap, DS1339_REG_ALARM1_SECS, regs,
473 sizeof(regs));
474 if (ret) {
475 dev_err(dev, "%s error %d\n", "alarm write", ret);
476 return ret;
477 }
478 control = regs[7];
479 status = regs[8];
480
481 dev_dbg(dev, "%s: %4ph, %3ph, %02x %02x\n", "alarm set (old status)",
482 ®s[0], ®s[4], control, status);
483
484 /* set ALARM1, using 24 hour and day-of-month modes */
485 regs[0] = bin2bcd(t->time.tm_sec);
486 regs[1] = bin2bcd(t->time.tm_min);
487 regs[2] = bin2bcd(t->time.tm_hour);
488 regs[3] = bin2bcd(t->time.tm_mday);
489
490 /* set ALARM2 to non-garbage */
491 regs[4] = 0;
492 regs[5] = 0;
493 regs[6] = 0;
494
495 /* disable alarms */
496 regs[7] = control & ~(DS1337_BIT_A1IE | DS1337_BIT_A2IE);
497 regs[8] = status & ~(DS1337_BIT_A1I | DS1337_BIT_A2I);
498
499 ret = regmap_bulk_write(ds1307->regmap, DS1339_REG_ALARM1_SECS, regs,
500 sizeof(regs));
501 if (ret) {
502 dev_err(dev, "can't set alarm time\n");
503 return ret;
504 }
505
506 /* optionally enable ALARM1 */
507 if (t->enabled) {
508 dev_dbg(dev, "alarm IRQ armed\n");
509 regs[7] |= DS1337_BIT_A1IE; /* only ALARM1 is used */
510 regmap_write(ds1307->regmap, DS1337_REG_CONTROL, regs[7]);
511 }
512
513 return 0;
514}
515
516static int ds1307_alarm_irq_enable(struct device *dev, unsigned int enabled)
517{
518 struct ds1307 *ds1307 = dev_get_drvdata(dev);
519
520 return regmap_update_bits(ds1307->regmap, DS1337_REG_CONTROL,
521 DS1337_BIT_A1IE,
522 enabled ? DS1337_BIT_A1IE : 0);
523}
524
525static u8 do_trickle_setup_ds1339(struct ds1307 *ds1307, u32 ohms, bool diode)
526{
527 u8 setup = (diode) ? DS1307_TRICKLE_CHARGER_DIODE :
528 DS1307_TRICKLE_CHARGER_NO_DIODE;
529
530 setup |= DS13XX_TRICKLE_CHARGER_MAGIC;
531
532 switch (ohms) {
533 case 250:
534 setup |= DS1307_TRICKLE_CHARGER_250_OHM;
535 break;
536 case 2000:
537 setup |= DS1307_TRICKLE_CHARGER_2K_OHM;
538 break;
539 case 4000:
540 setup |= DS1307_TRICKLE_CHARGER_4K_OHM;
541 break;
542 default:
543 dev_warn(ds1307->dev,
544 "Unsupported ohm value %u in dt\n", ohms);
545 return 0;
546 }
547 return setup;
548}
549
550static u8 do_trickle_setup_rx8130(struct ds1307 *ds1307, u32 ohms, bool diode)
551{
552 /* make sure that the backup battery is enabled */
553 u8 setup = RX8130_REG_CONTROL1_INIEN;
554 if (diode)
555 setup |= RX8130_REG_CONTROL1_CHGEN;
556
557 return setup;
558}
559
560static irqreturn_t rx8130_irq(int irq, void *dev_id)
561{
562 struct ds1307 *ds1307 = dev_id;
563 u8 ctl[3];
564 int ret;
565
566 rtc_lock(ds1307->rtc);
567
568 /* Read control registers. */
569 ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_EXTENSION, ctl,
570 sizeof(ctl));
571 if (ret < 0)
572 goto out;
573 if (!(ctl[1] & RX8130_REG_FLAG_AF))
574 goto out;
575 ctl[1] &= ~RX8130_REG_FLAG_AF;
576 ctl[2] &= ~RX8130_REG_CONTROL0_AIE;
577
578 ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_EXTENSION, ctl,
579 sizeof(ctl));
580 if (ret < 0)
581 goto out;
582
583 rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF);
584
585out:
586 rtc_unlock(ds1307->rtc);
587
588 return IRQ_HANDLED;
589}
590
591static int rx8130_read_alarm(struct device *dev, struct rtc_wkalrm *t)
592{
593 struct ds1307 *ds1307 = dev_get_drvdata(dev);
594 u8 ald[3], ctl[3];
595 int ret;
596
597 /* Read alarm registers. */
598 ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_ALARM_MIN, ald,
599 sizeof(ald));
600 if (ret < 0)
601 return ret;
602
603 /* Read control registers. */
604 ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_EXTENSION, ctl,
605 sizeof(ctl));
606 if (ret < 0)
607 return ret;
608
609 t->enabled = !!(ctl[2] & RX8130_REG_CONTROL0_AIE);
610 t->pending = !!(ctl[1] & RX8130_REG_FLAG_AF);
611
612 /* Report alarm 0 time assuming 24-hour and day-of-month modes. */
613 t->time.tm_sec = -1;
614 t->time.tm_min = bcd2bin(ald[0] & 0x7f);
615 t->time.tm_hour = bcd2bin(ald[1] & 0x7f);
616 t->time.tm_wday = -1;
617 t->time.tm_mday = bcd2bin(ald[2] & 0x7f);
618 t->time.tm_mon = -1;
619 t->time.tm_year = -1;
620 t->time.tm_yday = -1;
621 t->time.tm_isdst = -1;
622
623 dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d enabled=%d\n",
624 __func__, t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
625 t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, t->enabled);
626
627 return 0;
628}
629
630static int rx8130_set_alarm(struct device *dev, struct rtc_wkalrm *t)
631{
632 struct ds1307 *ds1307 = dev_get_drvdata(dev);
633 u8 ald[3], ctl[3];
634 int ret;
635
636 dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d "
637 "enabled=%d pending=%d\n", __func__,
638 t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
639 t->time.tm_wday, t->time.tm_mday, t->time.tm_mon,
640 t->enabled, t->pending);
641
642 /* Read control registers. */
643 ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_EXTENSION, ctl,
644 sizeof(ctl));
645 if (ret < 0)
646 return ret;
647
648 ctl[0] &= RX8130_REG_EXTENSION_WADA;
649 ctl[1] &= ~RX8130_REG_FLAG_AF;
650 ctl[2] &= ~RX8130_REG_CONTROL0_AIE;
651
652 ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_EXTENSION, ctl,
653 sizeof(ctl));
654 if (ret < 0)
655 return ret;
656
657 /* Hardware alarm precision is 1 minute! */
658 ald[0] = bin2bcd(t->time.tm_min);
659 ald[1] = bin2bcd(t->time.tm_hour);
660 ald[2] = bin2bcd(t->time.tm_mday);
661
662 ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_ALARM_MIN, ald,
663 sizeof(ald));
664 if (ret < 0)
665 return ret;
666
667 if (!t->enabled)
668 return 0;
669
670 ctl[2] |= RX8130_REG_CONTROL0_AIE;
671
672 return regmap_write(ds1307->regmap, RX8130_REG_CONTROL0, ctl[2]);
673}
674
675static int rx8130_alarm_irq_enable(struct device *dev, unsigned int enabled)
676{
677 struct ds1307 *ds1307 = dev_get_drvdata(dev);
678 int ret, reg;
679
680 ret = regmap_read(ds1307->regmap, RX8130_REG_CONTROL0, ®);
681 if (ret < 0)
682 return ret;
683
684 if (enabled)
685 reg |= RX8130_REG_CONTROL0_AIE;
686 else
687 reg &= ~RX8130_REG_CONTROL0_AIE;
688
689 return regmap_write(ds1307->regmap, RX8130_REG_CONTROL0, reg);
690}
691
692static irqreturn_t mcp794xx_irq(int irq, void *dev_id)
693{
694 struct ds1307 *ds1307 = dev_id;
695 struct mutex *lock = &ds1307->rtc->ops_lock;
696 int reg, ret;
697
698 mutex_lock(lock);
699
700 /* Check and clear alarm 0 interrupt flag. */
701 ret = regmap_read(ds1307->regmap, MCP794XX_REG_ALARM0_CTRL, ®);
702 if (ret)
703 goto out;
704 if (!(reg & MCP794XX_BIT_ALMX_IF))
705 goto out;
706 reg &= ~MCP794XX_BIT_ALMX_IF;
707 ret = regmap_write(ds1307->regmap, MCP794XX_REG_ALARM0_CTRL, reg);
708 if (ret)
709 goto out;
710
711 /* Disable alarm 0. */
712 ret = regmap_update_bits(ds1307->regmap, MCP794XX_REG_CONTROL,
713 MCP794XX_BIT_ALM0_EN, 0);
714 if (ret)
715 goto out;
716
717 rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF);
718
719out:
720 mutex_unlock(lock);
721
722 return IRQ_HANDLED;
723}
724
725static int mcp794xx_read_alarm(struct device *dev, struct rtc_wkalrm *t)
726{
727 struct ds1307 *ds1307 = dev_get_drvdata(dev);
728 u8 regs[10];
729 int ret;
730
731 /* Read control and alarm 0 registers. */
732 ret = regmap_bulk_read(ds1307->regmap, MCP794XX_REG_CONTROL, regs,
733 sizeof(regs));
734 if (ret)
735 return ret;
736
737 t->enabled = !!(regs[0] & MCP794XX_BIT_ALM0_EN);
738
739 /* Report alarm 0 time assuming 24-hour and day-of-month modes. */
740 t->time.tm_sec = bcd2bin(regs[3] & 0x7f);
741 t->time.tm_min = bcd2bin(regs[4] & 0x7f);
742 t->time.tm_hour = bcd2bin(regs[5] & 0x3f);
743 t->time.tm_wday = bcd2bin(regs[6] & 0x7) - 1;
744 t->time.tm_mday = bcd2bin(regs[7] & 0x3f);
745 t->time.tm_mon = bcd2bin(regs[8] & 0x1f) - 1;
746 t->time.tm_year = -1;
747 t->time.tm_yday = -1;
748 t->time.tm_isdst = -1;
749
750 dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d "
751 "enabled=%d polarity=%d irq=%d match=%lu\n", __func__,
752 t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
753 t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, t->enabled,
754 !!(regs[6] & MCP794XX_BIT_ALMX_POL),
755 !!(regs[6] & MCP794XX_BIT_ALMX_IF),
756 (regs[6] & MCP794XX_MSK_ALMX_MATCH) >> 4);
757
758 return 0;
759}
760
761/*
762 * We may have a random RTC weekday, therefore calculate alarm weekday based
763 * on current weekday we read from the RTC timekeeping regs
764 */
765static int mcp794xx_alm_weekday(struct device *dev, struct rtc_time *tm_alarm)
766{
767 struct rtc_time tm_now;
768 int days_now, days_alarm, ret;
769
770 ret = ds1307_get_time(dev, &tm_now);
771 if (ret)
772 return ret;
773
774 days_now = div_s64(rtc_tm_to_time64(&tm_now), 24 * 60 * 60);
775 days_alarm = div_s64(rtc_tm_to_time64(tm_alarm), 24 * 60 * 60);
776
777 return (tm_now.tm_wday + days_alarm - days_now) % 7 + 1;
778}
779
780static int mcp794xx_set_alarm(struct device *dev, struct rtc_wkalrm *t)
781{
782 struct ds1307 *ds1307 = dev_get_drvdata(dev);
783 unsigned char regs[10];
784 int wday, ret;
785
786 wday = mcp794xx_alm_weekday(dev, &t->time);
787 if (wday < 0)
788 return wday;
789
790 dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d "
791 "enabled=%d pending=%d\n", __func__,
792 t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
793 t->time.tm_wday, t->time.tm_mday, t->time.tm_mon,
794 t->enabled, t->pending);
795
796 /* Read control and alarm 0 registers. */
797 ret = regmap_bulk_read(ds1307->regmap, MCP794XX_REG_CONTROL, regs,
798 sizeof(regs));
799 if (ret)
800 return ret;
801
802 /* Set alarm 0, using 24-hour and day-of-month modes. */
803 regs[3] = bin2bcd(t->time.tm_sec);
804 regs[4] = bin2bcd(t->time.tm_min);
805 regs[5] = bin2bcd(t->time.tm_hour);
806 regs[6] = wday;
807 regs[7] = bin2bcd(t->time.tm_mday);
808 regs[8] = bin2bcd(t->time.tm_mon + 1);
809
810 /* Clear the alarm 0 interrupt flag. */
811 regs[6] &= ~MCP794XX_BIT_ALMX_IF;
812 /* Set alarm match: second, minute, hour, day, date, month. */
813 regs[6] |= MCP794XX_MSK_ALMX_MATCH;
814 /* Disable interrupt. We will not enable until completely programmed */
815 regs[0] &= ~MCP794XX_BIT_ALM0_EN;
816
817 ret = regmap_bulk_write(ds1307->regmap, MCP794XX_REG_CONTROL, regs,
818 sizeof(regs));
819 if (ret)
820 return ret;
821
822 if (!t->enabled)
823 return 0;
824 regs[0] |= MCP794XX_BIT_ALM0_EN;
825 return regmap_write(ds1307->regmap, MCP794XX_REG_CONTROL, regs[0]);
826}
827
828static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled)
829{
830 struct ds1307 *ds1307 = dev_get_drvdata(dev);
831
832 return regmap_update_bits(ds1307->regmap, MCP794XX_REG_CONTROL,
833 MCP794XX_BIT_ALM0_EN,
834 enabled ? MCP794XX_BIT_ALM0_EN : 0);
835}
836
837static int m41txx_rtc_read_offset(struct device *dev, long *offset)
838{
839 struct ds1307 *ds1307 = dev_get_drvdata(dev);
840 unsigned int ctrl_reg;
841 u8 val;
842
843 regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg);
844
845 val = ctrl_reg & M41TXX_M_CALIBRATION;
846
847 /* check if positive */
848 if (ctrl_reg & M41TXX_BIT_CALIB_SIGN)
849 *offset = (val * M41TXX_POS_OFFSET_STEP_PPB);
850 else
851 *offset = -(val * M41TXX_NEG_OFFSET_STEP_PPB);
852
853 return 0;
854}
855
856static int m41txx_rtc_set_offset(struct device *dev, long offset)
857{
858 struct ds1307 *ds1307 = dev_get_drvdata(dev);
859 unsigned int ctrl_reg;
860
861 if ((offset < M41TXX_MIN_OFFSET) || (offset > M41TXX_MAX_OFFSET))
862 return -ERANGE;
863
864 if (offset >= 0) {
865 ctrl_reg = DIV_ROUND_CLOSEST(offset,
866 M41TXX_POS_OFFSET_STEP_PPB);
867 ctrl_reg |= M41TXX_BIT_CALIB_SIGN;
868 } else {
869 ctrl_reg = DIV_ROUND_CLOSEST(abs(offset),
870 M41TXX_NEG_OFFSET_STEP_PPB);
871 }
872
873 return regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL,
874 M41TXX_M_CALIBRATION | M41TXX_BIT_CALIB_SIGN,
875 ctrl_reg);
876}
877
878#ifdef CONFIG_WATCHDOG_CORE
879static int ds1388_wdt_start(struct watchdog_device *wdt_dev)
880{
881 struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev);
882 u8 regs[2];
883 int ret;
884
885 ret = regmap_update_bits(ds1307->regmap, DS1388_REG_FLAG,
886 DS1388_BIT_WF, 0);
887 if (ret)
888 return ret;
889
890 ret = regmap_update_bits(ds1307->regmap, DS1388_REG_CONTROL,
891 DS1388_BIT_WDE | DS1388_BIT_RST, 0);
892 if (ret)
893 return ret;
894
895 /*
896 * watchdog timeouts are measured in seconds. So ignore hundredths of
897 * seconds field.
898 */
899 regs[0] = 0;
900 regs[1] = bin2bcd(wdt_dev->timeout);
901
902 ret = regmap_bulk_write(ds1307->regmap, DS1388_REG_WDOG_HUN_SECS, regs,
903 sizeof(regs));
904 if (ret)
905 return ret;
906
907 return regmap_update_bits(ds1307->regmap, DS1388_REG_CONTROL,
908 DS1388_BIT_WDE | DS1388_BIT_RST,
909 DS1388_BIT_WDE | DS1388_BIT_RST);
910}
911
912static int ds1388_wdt_stop(struct watchdog_device *wdt_dev)
913{
914 struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev);
915
916 return regmap_update_bits(ds1307->regmap, DS1388_REG_CONTROL,
917 DS1388_BIT_WDE | DS1388_BIT_RST, 0);
918}
919
920static int ds1388_wdt_ping(struct watchdog_device *wdt_dev)
921{
922 struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev);
923 u8 regs[2];
924
925 return regmap_bulk_read(ds1307->regmap, DS1388_REG_WDOG_HUN_SECS, regs,
926 sizeof(regs));
927}
928
929static int ds1388_wdt_set_timeout(struct watchdog_device *wdt_dev,
930 unsigned int val)
931{
932 struct ds1307 *ds1307 = watchdog_get_drvdata(wdt_dev);
933 u8 regs[2];
934
935 wdt_dev->timeout = val;
936 regs[0] = 0;
937 regs[1] = bin2bcd(wdt_dev->timeout);
938
939 return regmap_bulk_write(ds1307->regmap, DS1388_REG_WDOG_HUN_SECS, regs,
940 sizeof(regs));
941}
942#endif
943
944static const struct rtc_class_ops rx8130_rtc_ops = {
945 .read_time = ds1307_get_time,
946 .set_time = ds1307_set_time,
947 .read_alarm = rx8130_read_alarm,
948 .set_alarm = rx8130_set_alarm,
949 .alarm_irq_enable = rx8130_alarm_irq_enable,
950};
951
952static const struct rtc_class_ops mcp794xx_rtc_ops = {
953 .read_time = ds1307_get_time,
954 .set_time = ds1307_set_time,
955 .read_alarm = mcp794xx_read_alarm,
956 .set_alarm = mcp794xx_set_alarm,
957 .alarm_irq_enable = mcp794xx_alarm_irq_enable,
958};
959
960static const struct rtc_class_ops m41txx_rtc_ops = {
961 .read_time = ds1307_get_time,
962 .set_time = ds1307_set_time,
963 .read_alarm = ds1337_read_alarm,
964 .set_alarm = ds1337_set_alarm,
965 .alarm_irq_enable = ds1307_alarm_irq_enable,
966 .read_offset = m41txx_rtc_read_offset,
967 .set_offset = m41txx_rtc_set_offset,
968};
969
970static const struct chip_desc chips[last_ds_type] = {
971 [ds_1307] = {
972 .nvram_offset = 8,
973 .nvram_size = 56,
974 },
975 [ds_1308] = {
976 .nvram_offset = 8,
977 .nvram_size = 56,
978 },
979 [ds_1337] = {
980 .alarm = 1,
981 .century_reg = DS1307_REG_MONTH,
982 .century_bit = DS1337_BIT_CENTURY,
983 },
984 [ds_1338] = {
985 .nvram_offset = 8,
986 .nvram_size = 56,
987 },
988 [ds_1339] = {
989 .alarm = 1,
990 .century_reg = DS1307_REG_MONTH,
991 .century_bit = DS1337_BIT_CENTURY,
992 .bbsqi_bit = DS1339_BIT_BBSQI,
993 .trickle_charger_reg = 0x10,
994 .do_trickle_setup = &do_trickle_setup_ds1339,
995 .requires_trickle_resistor = true,
996 .charge_default = true,
997 },
998 [ds_1340] = {
999 .century_reg = DS1307_REG_HOUR,
1000 .century_enable_bit = DS1340_BIT_CENTURY_EN,
1001 .century_bit = DS1340_BIT_CENTURY,
1002 .do_trickle_setup = &do_trickle_setup_ds1339,
1003 .trickle_charger_reg = 0x08,
1004 .requires_trickle_resistor = true,
1005 .charge_default = true,
1006 },
1007 [ds_1341] = {
1008 .century_reg = DS1307_REG_MONTH,
1009 .century_bit = DS1337_BIT_CENTURY,
1010 },
1011 [ds_1388] = {
1012 .offset = 1,
1013 .trickle_charger_reg = 0x0a,
1014 },
1015 [ds_3231] = {
1016 .alarm = 1,
1017 .century_reg = DS1307_REG_MONTH,
1018 .century_bit = DS1337_BIT_CENTURY,
1019 .bbsqi_bit = DS3231_BIT_BBSQW,
1020 },
1021 [rx_8130] = {
1022 .alarm = 1,
1023 /* this is battery backed SRAM */
1024 .nvram_offset = 0x20,
1025 .nvram_size = 4, /* 32bit (4 word x 8 bit) */
1026 .offset = 0x10,
1027 .irq_handler = rx8130_irq,
1028 .rtc_ops = &rx8130_rtc_ops,
1029 .trickle_charger_reg = RX8130_REG_CONTROL1,
1030 .do_trickle_setup = &do_trickle_setup_rx8130,
1031 },
1032 [m41t0] = {
1033 .rtc_ops = &m41txx_rtc_ops,
1034 },
1035 [m41t00] = {
1036 .rtc_ops = &m41txx_rtc_ops,
1037 },
1038 [m41t11] = {
1039 /* this is battery backed SRAM */
1040 .nvram_offset = 8,
1041 .nvram_size = 56,
1042 .rtc_ops = &m41txx_rtc_ops,
1043 },
1044 [mcp794xx] = {
1045 .alarm = 1,
1046 /* this is battery backed SRAM */
1047 .nvram_offset = 0x20,
1048 .nvram_size = 0x40,
1049 .irq_handler = mcp794xx_irq,
1050 .rtc_ops = &mcp794xx_rtc_ops,
1051 },
1052};
1053
1054static const struct i2c_device_id ds1307_id[] = {
1055 { "ds1307", ds_1307 },
1056 { "ds1308", ds_1308 },
1057 { "ds1337", ds_1337 },
1058 { "ds1338", ds_1338 },
1059 { "ds1339", ds_1339 },
1060 { "ds1388", ds_1388 },
1061 { "ds1340", ds_1340 },
1062 { "ds1341", ds_1341 },
1063 { "ds3231", ds_3231 },
1064 { "m41t0", m41t0 },
1065 { "m41t00", m41t00 },
1066 { "m41t11", m41t11 },
1067 { "mcp7940x", mcp794xx },
1068 { "mcp7941x", mcp794xx },
1069 { "pt7c4338", ds_1307 },
1070 { "rx8025", rx_8025 },
1071 { "isl12057", ds_1337 },
1072 { "rx8130", rx_8130 },
1073 { }
1074};
1075MODULE_DEVICE_TABLE(i2c, ds1307_id);
1076
1077static const struct of_device_id ds1307_of_match[] = {
1078 {
1079 .compatible = "dallas,ds1307",
1080 .data = (void *)ds_1307
1081 },
1082 {
1083 .compatible = "dallas,ds1308",
1084 .data = (void *)ds_1308
1085 },
1086 {
1087 .compatible = "dallas,ds1337",
1088 .data = (void *)ds_1337
1089 },
1090 {
1091 .compatible = "dallas,ds1338",
1092 .data = (void *)ds_1338
1093 },
1094 {
1095 .compatible = "dallas,ds1339",
1096 .data = (void *)ds_1339
1097 },
1098 {
1099 .compatible = "dallas,ds1388",
1100 .data = (void *)ds_1388
1101 },
1102 {
1103 .compatible = "dallas,ds1340",
1104 .data = (void *)ds_1340
1105 },
1106 {
1107 .compatible = "dallas,ds1341",
1108 .data = (void *)ds_1341
1109 },
1110 {
1111 .compatible = "maxim,ds3231",
1112 .data = (void *)ds_3231
1113 },
1114 {
1115 .compatible = "st,m41t0",
1116 .data = (void *)m41t0
1117 },
1118 {
1119 .compatible = "st,m41t00",
1120 .data = (void *)m41t00
1121 },
1122 {
1123 .compatible = "st,m41t11",
1124 .data = (void *)m41t11
1125 },
1126 {
1127 .compatible = "microchip,mcp7940x",
1128 .data = (void *)mcp794xx
1129 },
1130 {
1131 .compatible = "microchip,mcp7941x",
1132 .data = (void *)mcp794xx
1133 },
1134 {
1135 .compatible = "pericom,pt7c4338",
1136 .data = (void *)ds_1307
1137 },
1138 {
1139 .compatible = "epson,rx8025",
1140 .data = (void *)rx_8025
1141 },
1142 {
1143 .compatible = "isil,isl12057",
1144 .data = (void *)ds_1337
1145 },
1146 {
1147 .compatible = "epson,rx8130",
1148 .data = (void *)rx_8130
1149 },
1150 { }
1151};
1152MODULE_DEVICE_TABLE(of, ds1307_of_match);
1153
1154/*
1155 * The ds1337 and ds1339 both have two alarms, but we only use the first
1156 * one (with a "seconds" field). For ds1337 we expect nINTA is our alarm
1157 * signal; ds1339 chips have only one alarm signal.
1158 */
1159static irqreturn_t ds1307_irq(int irq, void *dev_id)
1160{
1161 struct ds1307 *ds1307 = dev_id;
1162 struct mutex *lock = &ds1307->rtc->ops_lock;
1163 int stat, ret;
1164
1165 mutex_lock(lock);
1166 ret = regmap_read(ds1307->regmap, DS1337_REG_STATUS, &stat);
1167 if (ret)
1168 goto out;
1169
1170 if (stat & DS1337_BIT_A1I) {
1171 stat &= ~DS1337_BIT_A1I;
1172 regmap_write(ds1307->regmap, DS1337_REG_STATUS, stat);
1173
1174 ret = regmap_update_bits(ds1307->regmap, DS1337_REG_CONTROL,
1175 DS1337_BIT_A1IE, 0);
1176 if (ret)
1177 goto out;
1178
1179 rtc_update_irq(ds1307->rtc, 1, RTC_AF | RTC_IRQF);
1180 }
1181
1182out:
1183 mutex_unlock(lock);
1184
1185 return IRQ_HANDLED;
1186}
1187
1188/*----------------------------------------------------------------------*/
1189
1190static const struct rtc_class_ops ds13xx_rtc_ops = {
1191 .read_time = ds1307_get_time,
1192 .set_time = ds1307_set_time,
1193 .read_alarm = ds1337_read_alarm,
1194 .set_alarm = ds1337_set_alarm,
1195 .alarm_irq_enable = ds1307_alarm_irq_enable,
1196};
1197
1198static ssize_t frequency_test_store(struct device *dev,
1199 struct device_attribute *attr,
1200 const char *buf, size_t count)
1201{
1202 struct ds1307 *ds1307 = dev_get_drvdata(dev->parent);
1203 bool freq_test_en;
1204 int ret;
1205
1206 ret = kstrtobool(buf, &freq_test_en);
1207 if (ret) {
1208 dev_err(dev, "Failed to store RTC Frequency Test attribute\n");
1209 return ret;
1210 }
1211
1212 regmap_update_bits(ds1307->regmap, M41TXX_REG_CONTROL, M41TXX_BIT_FT,
1213 freq_test_en ? M41TXX_BIT_FT : 0);
1214
1215 return count;
1216}
1217
1218static ssize_t frequency_test_show(struct device *dev,
1219 struct device_attribute *attr,
1220 char *buf)
1221{
1222 struct ds1307 *ds1307 = dev_get_drvdata(dev->parent);
1223 unsigned int ctrl_reg;
1224
1225 regmap_read(ds1307->regmap, M41TXX_REG_CONTROL, &ctrl_reg);
1226
1227 return sysfs_emit(buf, (ctrl_reg & M41TXX_BIT_FT) ? "on\n" : "off\n");
1228}
1229
1230static DEVICE_ATTR_RW(frequency_test);
1231
1232static struct attribute *rtc_freq_test_attrs[] = {
1233 &dev_attr_frequency_test.attr,
1234 NULL,
1235};
1236
1237static const struct attribute_group rtc_freq_test_attr_group = {
1238 .attrs = rtc_freq_test_attrs,
1239};
1240
1241static int ds1307_add_frequency_test(struct ds1307 *ds1307)
1242{
1243 int err;
1244
1245 switch (ds1307->type) {
1246 case m41t0:
1247 case m41t00:
1248 case m41t11:
1249 err = rtc_add_group(ds1307->rtc, &rtc_freq_test_attr_group);
1250 if (err)
1251 return err;
1252 break;
1253 default:
1254 break;
1255 }
1256
1257 return 0;
1258}
1259
1260/*----------------------------------------------------------------------*/
1261
1262static int ds1307_nvram_read(void *priv, unsigned int offset, void *val,
1263 size_t bytes)
1264{
1265 struct ds1307 *ds1307 = priv;
1266 const struct chip_desc *chip = &chips[ds1307->type];
1267
1268 return regmap_bulk_read(ds1307->regmap, chip->nvram_offset + offset,
1269 val, bytes);
1270}
1271
1272static int ds1307_nvram_write(void *priv, unsigned int offset, void *val,
1273 size_t bytes)
1274{
1275 struct ds1307 *ds1307 = priv;
1276 const struct chip_desc *chip = &chips[ds1307->type];
1277
1278 return regmap_bulk_write(ds1307->regmap, chip->nvram_offset + offset,
1279 val, bytes);
1280}
1281
1282/*----------------------------------------------------------------------*/
1283
1284static u8 ds1307_trickle_init(struct ds1307 *ds1307,
1285 const struct chip_desc *chip)
1286{
1287 u32 ohms, chargeable;
1288 bool diode = chip->charge_default;
1289
1290 if (!chip->do_trickle_setup)
1291 return 0;
1292
1293 if (device_property_read_u32(ds1307->dev, "trickle-resistor-ohms",
1294 &ohms) && chip->requires_trickle_resistor)
1295 return 0;
1296
1297 /* aux-voltage-chargeable takes precedence over the deprecated
1298 * trickle-diode-disable
1299 */
1300 if (!device_property_read_u32(ds1307->dev, "aux-voltage-chargeable",
1301 &chargeable)) {
1302 switch (chargeable) {
1303 case 0:
1304 diode = false;
1305 break;
1306 case 1:
1307 diode = true;
1308 break;
1309 default:
1310 dev_warn(ds1307->dev,
1311 "unsupported aux-voltage-chargeable value\n");
1312 break;
1313 }
1314 } else if (device_property_read_bool(ds1307->dev,
1315 "trickle-diode-disable")) {
1316 diode = false;
1317 }
1318
1319 return chip->do_trickle_setup(ds1307, ohms, diode);
1320}
1321
1322/*----------------------------------------------------------------------*/
1323
1324#if IS_REACHABLE(CONFIG_HWMON)
1325
1326/*
1327 * Temperature sensor support for ds3231 devices.
1328 */
1329
1330#define DS3231_REG_TEMPERATURE 0x11
1331
1332/*
1333 * A user-initiated temperature conversion is not started by this function,
1334 * so the temperature is updated once every 64 seconds.
1335 */
1336static int ds3231_hwmon_read_temp(struct device *dev, s32 *mC)
1337{
1338 struct ds1307 *ds1307 = dev_get_drvdata(dev);
1339 u8 temp_buf[2];
1340 s16 temp;
1341 int ret;
1342
1343 ret = regmap_bulk_read(ds1307->regmap, DS3231_REG_TEMPERATURE,
1344 temp_buf, sizeof(temp_buf));
1345 if (ret)
1346 return ret;
1347 /*
1348 * Temperature is represented as a 10-bit code with a resolution of
1349 * 0.25 degree celsius and encoded in two's complement format.
1350 */
1351 temp = (temp_buf[0] << 8) | temp_buf[1];
1352 temp >>= 6;
1353 *mC = temp * 250;
1354
1355 return 0;
1356}
1357
1358static ssize_t ds3231_hwmon_show_temp(struct device *dev,
1359 struct device_attribute *attr, char *buf)
1360{
1361 int ret;
1362 s32 temp;
1363
1364 ret = ds3231_hwmon_read_temp(dev, &temp);
1365 if (ret)
1366 return ret;
1367
1368 return sprintf(buf, "%d\n", temp);
1369}
1370static SENSOR_DEVICE_ATTR(temp1_input, 0444, ds3231_hwmon_show_temp,
1371 NULL, 0);
1372
1373static struct attribute *ds3231_hwmon_attrs[] = {
1374 &sensor_dev_attr_temp1_input.dev_attr.attr,
1375 NULL,
1376};
1377ATTRIBUTE_GROUPS(ds3231_hwmon);
1378
1379static void ds1307_hwmon_register(struct ds1307 *ds1307)
1380{
1381 struct device *dev;
1382
1383 if (ds1307->type != ds_3231)
1384 return;
1385
1386 dev = devm_hwmon_device_register_with_groups(ds1307->dev, ds1307->name,
1387 ds1307,
1388 ds3231_hwmon_groups);
1389 if (IS_ERR(dev)) {
1390 dev_warn(ds1307->dev, "unable to register hwmon device %ld\n",
1391 PTR_ERR(dev));
1392 }
1393}
1394
1395#else
1396
1397static void ds1307_hwmon_register(struct ds1307 *ds1307)
1398{
1399}
1400
1401#endif /* CONFIG_RTC_DRV_DS1307_HWMON */
1402
1403/*----------------------------------------------------------------------*/
1404
1405/*
1406 * Square-wave output support for DS3231
1407 * Datasheet: https://datasheets.maximintegrated.com/en/ds/DS3231.pdf
1408 */
1409#ifdef CONFIG_COMMON_CLK
1410
1411enum {
1412 DS3231_CLK_SQW = 0,
1413 DS3231_CLK_32KHZ,
1414};
1415
1416#define clk_sqw_to_ds1307(clk) \
1417 container_of(clk, struct ds1307, clks[DS3231_CLK_SQW])
1418#define clk_32khz_to_ds1307(clk) \
1419 container_of(clk, struct ds1307, clks[DS3231_CLK_32KHZ])
1420
1421static int ds3231_clk_sqw_rates[] = {
1422 1,
1423 1024,
1424 4096,
1425 8192,
1426};
1427
1428static int ds1337_write_control(struct ds1307 *ds1307, u8 mask, u8 value)
1429{
1430 struct mutex *lock = &ds1307->rtc->ops_lock;
1431 int ret;
1432
1433 mutex_lock(lock);
1434 ret = regmap_update_bits(ds1307->regmap, DS1337_REG_CONTROL,
1435 mask, value);
1436 mutex_unlock(lock);
1437
1438 return ret;
1439}
1440
1441static unsigned long ds3231_clk_sqw_recalc_rate(struct clk_hw *hw,
1442 unsigned long parent_rate)
1443{
1444 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1445 int control, ret;
1446 int rate_sel = 0;
1447
1448 ret = regmap_read(ds1307->regmap, DS1337_REG_CONTROL, &control);
1449 if (ret)
1450 return ret;
1451 if (control & DS1337_BIT_RS1)
1452 rate_sel += 1;
1453 if (control & DS1337_BIT_RS2)
1454 rate_sel += 2;
1455
1456 return ds3231_clk_sqw_rates[rate_sel];
1457}
1458
1459static long ds3231_clk_sqw_round_rate(struct clk_hw *hw, unsigned long rate,
1460 unsigned long *prate)
1461{
1462 int i;
1463
1464 for (i = ARRAY_SIZE(ds3231_clk_sqw_rates) - 1; i >= 0; i--) {
1465 if (ds3231_clk_sqw_rates[i] <= rate)
1466 return ds3231_clk_sqw_rates[i];
1467 }
1468
1469 return 0;
1470}
1471
1472static int ds3231_clk_sqw_set_rate(struct clk_hw *hw, unsigned long rate,
1473 unsigned long parent_rate)
1474{
1475 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1476 int control = 0;
1477 int rate_sel;
1478
1479 for (rate_sel = 0; rate_sel < ARRAY_SIZE(ds3231_clk_sqw_rates);
1480 rate_sel++) {
1481 if (ds3231_clk_sqw_rates[rate_sel] == rate)
1482 break;
1483 }
1484
1485 if (rate_sel == ARRAY_SIZE(ds3231_clk_sqw_rates))
1486 return -EINVAL;
1487
1488 if (rate_sel & 1)
1489 control |= DS1337_BIT_RS1;
1490 if (rate_sel & 2)
1491 control |= DS1337_BIT_RS2;
1492
1493 return ds1337_write_control(ds1307, DS1337_BIT_RS1 | DS1337_BIT_RS2,
1494 control);
1495}
1496
1497static int ds3231_clk_sqw_prepare(struct clk_hw *hw)
1498{
1499 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1500
1501 return ds1337_write_control(ds1307, DS1337_BIT_INTCN, 0);
1502}
1503
1504static void ds3231_clk_sqw_unprepare(struct clk_hw *hw)
1505{
1506 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1507
1508 ds1337_write_control(ds1307, DS1337_BIT_INTCN, DS1337_BIT_INTCN);
1509}
1510
1511static int ds3231_clk_sqw_is_prepared(struct clk_hw *hw)
1512{
1513 struct ds1307 *ds1307 = clk_sqw_to_ds1307(hw);
1514 int control, ret;
1515
1516 ret = regmap_read(ds1307->regmap, DS1337_REG_CONTROL, &control);
1517 if (ret)
1518 return ret;
1519
1520 return !(control & DS1337_BIT_INTCN);
1521}
1522
1523static const struct clk_ops ds3231_clk_sqw_ops = {
1524 .prepare = ds3231_clk_sqw_prepare,
1525 .unprepare = ds3231_clk_sqw_unprepare,
1526 .is_prepared = ds3231_clk_sqw_is_prepared,
1527 .recalc_rate = ds3231_clk_sqw_recalc_rate,
1528 .round_rate = ds3231_clk_sqw_round_rate,
1529 .set_rate = ds3231_clk_sqw_set_rate,
1530};
1531
1532static unsigned long ds3231_clk_32khz_recalc_rate(struct clk_hw *hw,
1533 unsigned long parent_rate)
1534{
1535 return 32768;
1536}
1537
1538static int ds3231_clk_32khz_control(struct ds1307 *ds1307, bool enable)
1539{
1540 struct mutex *lock = &ds1307->rtc->ops_lock;
1541 int ret;
1542
1543 mutex_lock(lock);
1544 ret = regmap_update_bits(ds1307->regmap, DS1337_REG_STATUS,
1545 DS3231_BIT_EN32KHZ,
1546 enable ? DS3231_BIT_EN32KHZ : 0);
1547 mutex_unlock(lock);
1548
1549 return ret;
1550}
1551
1552static int ds3231_clk_32khz_prepare(struct clk_hw *hw)
1553{
1554 struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw);
1555
1556 return ds3231_clk_32khz_control(ds1307, true);
1557}
1558
1559static void ds3231_clk_32khz_unprepare(struct clk_hw *hw)
1560{
1561 struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw);
1562
1563 ds3231_clk_32khz_control(ds1307, false);
1564}
1565
1566static int ds3231_clk_32khz_is_prepared(struct clk_hw *hw)
1567{
1568 struct ds1307 *ds1307 = clk_32khz_to_ds1307(hw);
1569 int status, ret;
1570
1571 ret = regmap_read(ds1307->regmap, DS1337_REG_STATUS, &status);
1572 if (ret)
1573 return ret;
1574
1575 return !!(status & DS3231_BIT_EN32KHZ);
1576}
1577
1578static const struct clk_ops ds3231_clk_32khz_ops = {
1579 .prepare = ds3231_clk_32khz_prepare,
1580 .unprepare = ds3231_clk_32khz_unprepare,
1581 .is_prepared = ds3231_clk_32khz_is_prepared,
1582 .recalc_rate = ds3231_clk_32khz_recalc_rate,
1583};
1584
1585static const char *ds3231_clks_names[] = {
1586 [DS3231_CLK_SQW] = "ds3231_clk_sqw",
1587 [DS3231_CLK_32KHZ] = "ds3231_clk_32khz",
1588};
1589
1590static struct clk_init_data ds3231_clks_init[] = {
1591 [DS3231_CLK_SQW] = {
1592 .ops = &ds3231_clk_sqw_ops,
1593 },
1594 [DS3231_CLK_32KHZ] = {
1595 .ops = &ds3231_clk_32khz_ops,
1596 },
1597};
1598
1599static int ds3231_clks_register(struct ds1307 *ds1307)
1600{
1601 struct device_node *node = ds1307->dev->of_node;
1602 struct clk_onecell_data *onecell;
1603 int i;
1604
1605 onecell = devm_kzalloc(ds1307->dev, sizeof(*onecell), GFP_KERNEL);
1606 if (!onecell)
1607 return -ENOMEM;
1608
1609 onecell->clk_num = ARRAY_SIZE(ds3231_clks_init);
1610 onecell->clks = devm_kcalloc(ds1307->dev, onecell->clk_num,
1611 sizeof(onecell->clks[0]), GFP_KERNEL);
1612 if (!onecell->clks)
1613 return -ENOMEM;
1614
1615 /* optional override of the clockname */
1616 device_property_read_string_array(ds1307->dev, "clock-output-names",
1617 ds3231_clks_names,
1618 ARRAY_SIZE(ds3231_clks_names));
1619
1620 for (i = 0; i < ARRAY_SIZE(ds3231_clks_init); i++) {
1621 struct clk_init_data init = ds3231_clks_init[i];
1622
1623 /*
1624 * Interrupt signal due to alarm conditions and square-wave
1625 * output share same pin, so don't initialize both.
1626 */
1627 if (i == DS3231_CLK_SQW && test_bit(RTC_FEATURE_ALARM, ds1307->rtc->features))
1628 continue;
1629
1630 init.name = ds3231_clks_names[i];
1631 ds1307->clks[i].init = &init;
1632
1633 onecell->clks[i] = devm_clk_register(ds1307->dev,
1634 &ds1307->clks[i]);
1635 if (IS_ERR(onecell->clks[i]))
1636 return PTR_ERR(onecell->clks[i]);
1637 }
1638
1639 if (node)
1640 of_clk_add_provider(node, of_clk_src_onecell_get, onecell);
1641
1642 return 0;
1643}
1644
1645static void ds1307_clks_register(struct ds1307 *ds1307)
1646{
1647 int ret;
1648
1649 if (ds1307->type != ds_3231)
1650 return;
1651
1652 ret = ds3231_clks_register(ds1307);
1653 if (ret) {
1654 dev_warn(ds1307->dev, "unable to register clock device %d\n",
1655 ret);
1656 }
1657}
1658
1659#else
1660
1661static void ds1307_clks_register(struct ds1307 *ds1307)
1662{
1663}
1664
1665#endif /* CONFIG_COMMON_CLK */
1666
1667#ifdef CONFIG_WATCHDOG_CORE
1668static const struct watchdog_info ds1388_wdt_info = {
1669 .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE,
1670 .identity = "DS1388 watchdog",
1671};
1672
1673static const struct watchdog_ops ds1388_wdt_ops = {
1674 .owner = THIS_MODULE,
1675 .start = ds1388_wdt_start,
1676 .stop = ds1388_wdt_stop,
1677 .ping = ds1388_wdt_ping,
1678 .set_timeout = ds1388_wdt_set_timeout,
1679
1680};
1681
1682static void ds1307_wdt_register(struct ds1307 *ds1307)
1683{
1684 struct watchdog_device *wdt;
1685 int err;
1686 int val;
1687
1688 if (ds1307->type != ds_1388)
1689 return;
1690
1691 wdt = devm_kzalloc(ds1307->dev, sizeof(*wdt), GFP_KERNEL);
1692 if (!wdt)
1693 return;
1694
1695 err = regmap_read(ds1307->regmap, DS1388_REG_FLAG, &val);
1696 if (!err && val & DS1388_BIT_WF)
1697 wdt->bootstatus = WDIOF_CARDRESET;
1698
1699 wdt->info = &ds1388_wdt_info;
1700 wdt->ops = &ds1388_wdt_ops;
1701 wdt->timeout = 99;
1702 wdt->max_timeout = 99;
1703 wdt->min_timeout = 1;
1704
1705 watchdog_init_timeout(wdt, 0, ds1307->dev);
1706 watchdog_set_drvdata(wdt, ds1307);
1707 devm_watchdog_register_device(ds1307->dev, wdt);
1708}
1709#else
1710static void ds1307_wdt_register(struct ds1307 *ds1307)
1711{
1712}
1713#endif /* CONFIG_WATCHDOG_CORE */
1714
1715static const struct regmap_config regmap_config = {
1716 .reg_bits = 8,
1717 .val_bits = 8,
1718};
1719
1720static int ds1307_probe(struct i2c_client *client)
1721{
1722 const struct i2c_device_id *id = i2c_client_get_device_id(client);
1723 struct ds1307 *ds1307;
1724 const void *match;
1725 int err = -ENODEV;
1726 int tmp;
1727 const struct chip_desc *chip;
1728 bool want_irq;
1729 bool ds1307_can_wakeup_device = false;
1730 unsigned char regs[8];
1731 struct ds1307_platform_data *pdata = dev_get_platdata(&client->dev);
1732 u8 trickle_charger_setup = 0;
1733
1734 ds1307 = devm_kzalloc(&client->dev, sizeof(struct ds1307), GFP_KERNEL);
1735 if (!ds1307)
1736 return -ENOMEM;
1737
1738 dev_set_drvdata(&client->dev, ds1307);
1739 ds1307->dev = &client->dev;
1740 ds1307->name = client->name;
1741
1742 ds1307->regmap = devm_regmap_init_i2c(client, ®map_config);
1743 if (IS_ERR(ds1307->regmap)) {
1744 dev_err(ds1307->dev, "regmap allocation failed\n");
1745 return PTR_ERR(ds1307->regmap);
1746 }
1747
1748 i2c_set_clientdata(client, ds1307);
1749
1750 match = device_get_match_data(&client->dev);
1751 if (match) {
1752 ds1307->type = (uintptr_t)match;
1753 chip = &chips[ds1307->type];
1754 } else if (id) {
1755 chip = &chips[id->driver_data];
1756 ds1307->type = id->driver_data;
1757 } else {
1758 return -ENODEV;
1759 }
1760
1761 want_irq = client->irq > 0 && chip->alarm;
1762
1763 if (!pdata)
1764 trickle_charger_setup = ds1307_trickle_init(ds1307, chip);
1765 else if (pdata->trickle_charger_setup)
1766 trickle_charger_setup = pdata->trickle_charger_setup;
1767
1768 if (trickle_charger_setup && chip->trickle_charger_reg) {
1769 dev_dbg(ds1307->dev,
1770 "writing trickle charger info 0x%x to 0x%x\n",
1771 trickle_charger_setup, chip->trickle_charger_reg);
1772 regmap_write(ds1307->regmap, chip->trickle_charger_reg,
1773 trickle_charger_setup);
1774 }
1775
1776/*
1777 * For devices with no IRQ directly connected to the SoC, the RTC chip
1778 * can be forced as a wakeup source by stating that explicitly in
1779 * the device's .dts file using the "wakeup-source" boolean property.
1780 * If the "wakeup-source" property is set, don't request an IRQ.
1781 * This will guarantee the 'wakealarm' sysfs entry is available on the device,
1782 * if supported by the RTC.
1783 */
1784 if (chip->alarm && device_property_read_bool(&client->dev, "wakeup-source"))
1785 ds1307_can_wakeup_device = true;
1786
1787 switch (ds1307->type) {
1788 case ds_1337:
1789 case ds_1339:
1790 case ds_1341:
1791 case ds_3231:
1792 /* get registers that the "rtc" read below won't read... */
1793 err = regmap_bulk_read(ds1307->regmap, DS1337_REG_CONTROL,
1794 regs, 2);
1795 if (err) {
1796 dev_dbg(ds1307->dev, "read error %d\n", err);
1797 goto exit;
1798 }
1799
1800 /* oscillator off? turn it on, so clock can tick. */
1801 if (regs[0] & DS1337_BIT_nEOSC)
1802 regs[0] &= ~DS1337_BIT_nEOSC;
1803
1804 /*
1805 * Using IRQ or defined as wakeup-source?
1806 * Disable the square wave and both alarms.
1807 * For some variants, be sure alarms can trigger when we're
1808 * running on Vbackup (BBSQI/BBSQW)
1809 */
1810 if (want_irq || ds1307_can_wakeup_device) {
1811 regs[0] |= DS1337_BIT_INTCN | chip->bbsqi_bit;
1812 regs[0] &= ~(DS1337_BIT_A2IE | DS1337_BIT_A1IE);
1813 }
1814
1815 regmap_write(ds1307->regmap, DS1337_REG_CONTROL,
1816 regs[0]);
1817
1818 /* oscillator fault? clear flag, and warn */
1819 if (regs[1] & DS1337_BIT_OSF) {
1820 regmap_write(ds1307->regmap, DS1337_REG_STATUS,
1821 regs[1] & ~DS1337_BIT_OSF);
1822 dev_warn(ds1307->dev, "SET TIME!\n");
1823 }
1824 break;
1825
1826 case rx_8025:
1827 err = regmap_bulk_read(ds1307->regmap,
1828 RX8025_REG_CTRL1 << 4 | 0x08, regs, 2);
1829 if (err) {
1830 dev_dbg(ds1307->dev, "read error %d\n", err);
1831 goto exit;
1832 }
1833
1834 /* oscillator off? turn it on, so clock can tick. */
1835 if (!(regs[1] & RX8025_BIT_XST)) {
1836 regs[1] |= RX8025_BIT_XST;
1837 regmap_write(ds1307->regmap,
1838 RX8025_REG_CTRL2 << 4 | 0x08,
1839 regs[1]);
1840 dev_warn(ds1307->dev,
1841 "oscillator stop detected - SET TIME!\n");
1842 }
1843
1844 if (regs[1] & RX8025_BIT_PON) {
1845 regs[1] &= ~RX8025_BIT_PON;
1846 regmap_write(ds1307->regmap,
1847 RX8025_REG_CTRL2 << 4 | 0x08,
1848 regs[1]);
1849 dev_warn(ds1307->dev, "power-on detected\n");
1850 }
1851
1852 if (regs[1] & RX8025_BIT_VDET) {
1853 regs[1] &= ~RX8025_BIT_VDET;
1854 regmap_write(ds1307->regmap,
1855 RX8025_REG_CTRL2 << 4 | 0x08,
1856 regs[1]);
1857 dev_warn(ds1307->dev, "voltage drop detected\n");
1858 }
1859
1860 /* make sure we are running in 24hour mode */
1861 if (!(regs[0] & RX8025_BIT_2412)) {
1862 u8 hour;
1863
1864 /* switch to 24 hour mode */
1865 regmap_write(ds1307->regmap,
1866 RX8025_REG_CTRL1 << 4 | 0x08,
1867 regs[0] | RX8025_BIT_2412);
1868
1869 err = regmap_bulk_read(ds1307->regmap,
1870 RX8025_REG_CTRL1 << 4 | 0x08,
1871 regs, 2);
1872 if (err) {
1873 dev_dbg(ds1307->dev, "read error %d\n", err);
1874 goto exit;
1875 }
1876
1877 /* correct hour */
1878 hour = bcd2bin(regs[DS1307_REG_HOUR]);
1879 if (hour == 12)
1880 hour = 0;
1881 if (regs[DS1307_REG_HOUR] & DS1307_BIT_PM)
1882 hour += 12;
1883
1884 regmap_write(ds1307->regmap,
1885 DS1307_REG_HOUR << 4 | 0x08, hour);
1886 }
1887 break;
1888 case ds_1388:
1889 err = regmap_read(ds1307->regmap, DS1388_REG_CONTROL, &tmp);
1890 if (err) {
1891 dev_dbg(ds1307->dev, "read error %d\n", err);
1892 goto exit;
1893 }
1894
1895 /* oscillator off? turn it on, so clock can tick. */
1896 if (tmp & DS1388_BIT_nEOSC) {
1897 tmp &= ~DS1388_BIT_nEOSC;
1898 regmap_write(ds1307->regmap, DS1388_REG_CONTROL, tmp);
1899 }
1900 break;
1901 default:
1902 break;
1903 }
1904
1905 /* read RTC registers */
1906 err = regmap_bulk_read(ds1307->regmap, chip->offset, regs,
1907 sizeof(regs));
1908 if (err) {
1909 dev_dbg(ds1307->dev, "read error %d\n", err);
1910 goto exit;
1911 }
1912
1913 if (ds1307->type == mcp794xx &&
1914 !(regs[DS1307_REG_WDAY] & MCP794XX_BIT_VBATEN)) {
1915 regmap_write(ds1307->regmap, DS1307_REG_WDAY,
1916 regs[DS1307_REG_WDAY] |
1917 MCP794XX_BIT_VBATEN);
1918 }
1919
1920 tmp = regs[DS1307_REG_HOUR];
1921 switch (ds1307->type) {
1922 case ds_1340:
1923 case m41t0:
1924 case m41t00:
1925 case m41t11:
1926 /*
1927 * NOTE: ignores century bits; fix before deploying
1928 * systems that will run through year 2100.
1929 */
1930 break;
1931 case rx_8025:
1932 break;
1933 default:
1934 if (!(tmp & DS1307_BIT_12HR))
1935 break;
1936
1937 /*
1938 * Be sure we're in 24 hour mode. Multi-master systems
1939 * take note...
1940 */
1941 tmp = bcd2bin(tmp & 0x1f);
1942 if (tmp == 12)
1943 tmp = 0;
1944 if (regs[DS1307_REG_HOUR] & DS1307_BIT_PM)
1945 tmp += 12;
1946 regmap_write(ds1307->regmap, chip->offset + DS1307_REG_HOUR,
1947 bin2bcd(tmp));
1948 }
1949
1950 ds1307->rtc = devm_rtc_allocate_device(ds1307->dev);
1951 if (IS_ERR(ds1307->rtc))
1952 return PTR_ERR(ds1307->rtc);
1953
1954 if (want_irq || ds1307_can_wakeup_device)
1955 device_set_wakeup_capable(ds1307->dev, true);
1956 else
1957 clear_bit(RTC_FEATURE_ALARM, ds1307->rtc->features);
1958
1959 if (ds1307_can_wakeup_device && !want_irq) {
1960 dev_info(ds1307->dev,
1961 "'wakeup-source' is set, request for an IRQ is disabled!\n");
1962 /* We cannot support UIE mode if we do not have an IRQ line */
1963 clear_bit(RTC_FEATURE_UPDATE_INTERRUPT, ds1307->rtc->features);
1964 }
1965
1966 if (want_irq) {
1967 err = devm_request_threaded_irq(ds1307->dev, client->irq, NULL,
1968 chip->irq_handler ?: ds1307_irq,
1969 IRQF_SHARED | IRQF_ONESHOT,
1970 ds1307->name, ds1307);
1971 if (err) {
1972 client->irq = 0;
1973 device_set_wakeup_capable(ds1307->dev, false);
1974 clear_bit(RTC_FEATURE_ALARM, ds1307->rtc->features);
1975 dev_err(ds1307->dev, "unable to request IRQ!\n");
1976 } else {
1977 dev_dbg(ds1307->dev, "got IRQ %d\n", client->irq);
1978 }
1979 }
1980
1981 ds1307->rtc->ops = chip->rtc_ops ?: &ds13xx_rtc_ops;
1982 err = ds1307_add_frequency_test(ds1307);
1983 if (err)
1984 return err;
1985
1986 err = devm_rtc_register_device(ds1307->rtc);
1987 if (err)
1988 return err;
1989
1990 if (chip->nvram_size) {
1991 struct nvmem_config nvmem_cfg = {
1992 .name = "ds1307_nvram",
1993 .word_size = 1,
1994 .stride = 1,
1995 .size = chip->nvram_size,
1996 .reg_read = ds1307_nvram_read,
1997 .reg_write = ds1307_nvram_write,
1998 .priv = ds1307,
1999 };
2000
2001 devm_rtc_nvmem_register(ds1307->rtc, &nvmem_cfg);
2002 }
2003
2004 ds1307_hwmon_register(ds1307);
2005 ds1307_clks_register(ds1307);
2006 ds1307_wdt_register(ds1307);
2007
2008 return 0;
2009
2010exit:
2011 return err;
2012}
2013
2014static struct i2c_driver ds1307_driver = {
2015 .driver = {
2016 .name = "rtc-ds1307",
2017 .of_match_table = ds1307_of_match,
2018 },
2019 .probe = ds1307_probe,
2020 .id_table = ds1307_id,
2021};
2022
2023module_i2c_driver(ds1307_driver);
2024
2025MODULE_DESCRIPTION("RTC driver for DS1307 and similar chips");
2026MODULE_LICENSE("GPL");