Loading...
1/*
2 * linux/arch/arm/mach-omap1/board-osk.c
3 *
4 * Board specific init for OMAP5912 OSK
5 *
6 * Written by Dirk Behme <dirk.behme@de.bosch.com>
7 *
8 * This program is free software; you can redistribute it and/or modify it
9 * under the terms of the GNU General Public License as published by the
10 * Free Software Foundation; either version 2 of the License, or (at your
11 * option) any later version.
12 *
13 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
14 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
15 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
16 * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
17 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
18 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
19 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
20 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
21 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
22 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
23 *
24 * You should have received a copy of the GNU General Public License along
25 * with this program; if not, write to the Free Software Foundation, Inc.,
26 * 675 Mass Ave, Cambridge, MA 02139, USA.
27 */
28#include <linux/gpio.h>
29#include <linux/kernel.h>
30#include <linux/init.h>
31#include <linux/platform_device.h>
32#include <linux/interrupt.h>
33#include <linux/irq.h>
34#include <linux/i2c.h>
35#include <linux/leds.h>
36#include <linux/smc91x.h>
37#include <linux/omapfb.h>
38#include <linux/mtd/mtd.h>
39#include <linux/mtd/partitions.h>
40#include <linux/mtd/physmap.h>
41#include <linux/i2c/tps65010.h>
42#include <linux/platform_data/gpio-omap.h>
43#include <linux/platform_data/omap1_bl.h>
44
45#include <asm/mach-types.h>
46#include <asm/mach/arch.h>
47#include <asm/mach/map.h>
48
49#include <mach/flash.h>
50#include <mach/mux.h>
51#include <mach/tc.h>
52
53#include <mach/hardware.h>
54#include <mach/usb.h>
55
56#include "common.h"
57
58/* At OMAP5912 OSK the Ethernet is directly connected to CS1 */
59#define OMAP_OSK_ETHR_START 0x04800300
60
61/* TPS65010 has four GPIOs. nPG and LED2 can be treated like GPIOs with
62 * alternate pin configurations for hardware-controlled blinking.
63 */
64#define OSK_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
65# define OSK_TPS_GPIO_USB_PWR_EN (OSK_TPS_GPIO_BASE + 0)
66# define OSK_TPS_GPIO_LED_D3 (OSK_TPS_GPIO_BASE + 1)
67# define OSK_TPS_GPIO_LAN_RESET (OSK_TPS_GPIO_BASE + 2)
68# define OSK_TPS_GPIO_DSP_PWR_EN (OSK_TPS_GPIO_BASE + 3)
69# define OSK_TPS_GPIO_LED_D9 (OSK_TPS_GPIO_BASE + 4)
70# define OSK_TPS_GPIO_LED_D2 (OSK_TPS_GPIO_BASE + 5)
71
72static struct mtd_partition osk_partitions[] = {
73 /* bootloader (U-Boot, etc) in first sector */
74 {
75 .name = "bootloader",
76 .offset = 0,
77 .size = SZ_128K,
78 .mask_flags = MTD_WRITEABLE, /* force read-only */
79 },
80 /* bootloader params in the next sector */
81 {
82 .name = "params",
83 .offset = MTDPART_OFS_APPEND,
84 .size = SZ_128K,
85 .mask_flags = 0,
86 }, {
87 .name = "kernel",
88 .offset = MTDPART_OFS_APPEND,
89 .size = SZ_2M,
90 .mask_flags = 0
91 }, {
92 .name = "filesystem",
93 .offset = MTDPART_OFS_APPEND,
94 .size = MTDPART_SIZ_FULL,
95 .mask_flags = 0
96 }
97};
98
99static struct physmap_flash_data osk_flash_data = {
100 .width = 2,
101 .set_vpp = omap1_set_vpp,
102 .parts = osk_partitions,
103 .nr_parts = ARRAY_SIZE(osk_partitions),
104};
105
106static struct resource osk_flash_resource = {
107 /* this is on CS3, wherever it's mapped */
108 .flags = IORESOURCE_MEM,
109};
110
111static struct platform_device osk5912_flash_device = {
112 .name = "physmap-flash",
113 .id = 0,
114 .dev = {
115 .platform_data = &osk_flash_data,
116 },
117 .num_resources = 1,
118 .resource = &osk_flash_resource,
119};
120
121static struct smc91x_platdata osk5912_smc91x_info = {
122 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
123 .leda = RPC_LED_100_10,
124 .ledb = RPC_LED_TX_RX,
125};
126
127static struct resource osk5912_smc91x_resources[] = {
128 [0] = {
129 .start = OMAP_OSK_ETHR_START, /* Physical */
130 .end = OMAP_OSK_ETHR_START + 0xf,
131 .flags = IORESOURCE_MEM,
132 },
133 [1] = {
134 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
135 },
136};
137
138static struct platform_device osk5912_smc91x_device = {
139 .name = "smc91x",
140 .id = -1,
141 .dev = {
142 .platform_data = &osk5912_smc91x_info,
143 },
144 .num_resources = ARRAY_SIZE(osk5912_smc91x_resources),
145 .resource = osk5912_smc91x_resources,
146};
147
148static struct resource osk5912_cf_resources[] = {
149 [0] = {
150 .flags = IORESOURCE_IRQ,
151 },
152};
153
154static struct platform_device osk5912_cf_device = {
155 .name = "omap_cf",
156 .id = -1,
157 .dev = {
158 .platform_data = (void *) 2 /* CS2 */,
159 },
160 .num_resources = ARRAY_SIZE(osk5912_cf_resources),
161 .resource = osk5912_cf_resources,
162};
163
164static struct platform_device *osk5912_devices[] __initdata = {
165 &osk5912_flash_device,
166 &osk5912_smc91x_device,
167 &osk5912_cf_device,
168};
169
170static struct gpio_led tps_leds[] = {
171 /* NOTE: D9 and D2 have hardware blink support.
172 * Also, D9 requires non-battery power.
173 */
174 { .gpio = OSK_TPS_GPIO_LED_D9, .name = "d9",
175 .default_trigger = "ide-disk", },
176 { .gpio = OSK_TPS_GPIO_LED_D2, .name = "d2", },
177 { .gpio = OSK_TPS_GPIO_LED_D3, .name = "d3", .active_low = 1,
178 .default_trigger = "heartbeat", },
179};
180
181static struct gpio_led_platform_data tps_leds_data = {
182 .num_leds = 3,
183 .leds = tps_leds,
184};
185
186static struct platform_device osk5912_tps_leds = {
187 .name = "leds-gpio",
188 .id = 0,
189 .dev.platform_data = &tps_leds_data,
190};
191
192static int osk_tps_setup(struct i2c_client *client, void *context)
193{
194 if (!IS_BUILTIN(CONFIG_TPS65010))
195 return -ENOSYS;
196
197 /* Set GPIO 1 HIGH to disable VBUS power supply;
198 * OHCI driver powers it up/down as needed.
199 */
200 gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
201 gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
202
203 /* Set GPIO 2 high so LED D3 is off by default */
204 tps65010_set_gpio_out_value(GPIO2, HIGH);
205
206 /* Set GPIO 3 low to take ethernet out of reset */
207 gpio_request(OSK_TPS_GPIO_LAN_RESET, "smc_reset");
208 gpio_direction_output(OSK_TPS_GPIO_LAN_RESET, 0);
209
210 /* GPIO4 is VDD_DSP */
211 gpio_request(OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power");
212 gpio_direction_output(OSK_TPS_GPIO_DSP_PWR_EN, 1);
213 /* REVISIT if DSP support isn't configured, power it off ... */
214
215 /* Let LED1 (D9) blink; leds-gpio may override it */
216 tps65010_set_led(LED1, BLINK);
217
218 /* Set LED2 off by default */
219 tps65010_set_led(LED2, OFF);
220
221 /* Enable LOW_PWR handshake */
222 tps65010_set_low_pwr(ON);
223
224 /* Switch VLDO2 to 3.0V for AIC23 */
225 tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
226 | TPS_LDO1_ENABLE);
227
228 /* register these three LEDs */
229 osk5912_tps_leds.dev.parent = &client->dev;
230 platform_device_register(&osk5912_tps_leds);
231
232 return 0;
233}
234
235static struct tps65010_board tps_board = {
236 .base = OSK_TPS_GPIO_BASE,
237 .outmask = 0x0f,
238 .setup = osk_tps_setup,
239};
240
241static struct i2c_board_info __initdata osk_i2c_board_info[] = {
242 {
243 I2C_BOARD_INFO("tps65010", 0x48),
244 .platform_data = &tps_board,
245
246 },
247 {
248 I2C_BOARD_INFO("tlv320aic23", 0x1B),
249 },
250 /* TODO when driver support is ready:
251 * - optionally on Mistral, ov9640 camera sensor at 0x30
252 */
253};
254
255static void __init osk_init_smc91x(void)
256{
257 u32 l;
258
259 if ((gpio_request(0, "smc_irq")) < 0) {
260 printk("Error requesting gpio 0 for smc91x irq\n");
261 return;
262 }
263
264 /* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
265 l = omap_readl(EMIFS_CCS(1));
266 l |= 0x3;
267 omap_writel(l, EMIFS_CCS(1));
268}
269
270static void __init osk_init_cf(void)
271{
272 omap_cfg_reg(M7_1610_GPIO62);
273 if ((gpio_request(62, "cf_irq")) < 0) {
274 printk("Error requesting gpio 62 for CF irq\n");
275 return;
276 }
277 /* the CF I/O IRQ is really active-low */
278 irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING);
279}
280
281static struct omap_usb_config osk_usb_config __initdata = {
282 /* has usb host connector (A) ... for development it can also
283 * be used, with a NONSTANDARD gender-bending cable/dongle, as
284 * a peripheral.
285 */
286#ifdef CONFIG_USB_GADGET_OMAP
287 .register_dev = 1,
288 .hmc_mode = 0,
289#else
290 .register_host = 1,
291 .hmc_mode = 16,
292 .rwc = 1,
293#endif
294 .pins[0] = 2,
295};
296
297#ifdef CONFIG_OMAP_OSK_MISTRAL
298static struct omap_lcd_config osk_lcd_config __initdata = {
299 .ctrl_name = "internal",
300};
301#endif
302
303#ifdef CONFIG_OMAP_OSK_MISTRAL
304
305#include <linux/input.h>
306#include <linux/platform_data/at24.h>
307#include <linux/spi/spi.h>
308#include <linux/spi/ads7846.h>
309
310#include <linux/platform_data/keypad-omap.h>
311
312static struct at24_platform_data at24c04 = {
313 .byte_len = SZ_4K / 8,
314 .page_size = 16,
315};
316
317static struct i2c_board_info __initdata mistral_i2c_board_info[] = {
318 {
319 /* NOTE: powered from LCD supply */
320 I2C_BOARD_INFO("24c04", 0x50),
321 .platform_data = &at24c04,
322 },
323 /* TODO when driver support is ready:
324 * - optionally ov9640 camera sensor at 0x30
325 */
326};
327
328static const unsigned int osk_keymap[] = {
329 /* KEY(col, row, code) */
330 KEY(0, 0, KEY_F1), /* SW4 */
331 KEY(3, 0, KEY_UP), /* (sw2/up) */
332 KEY(1, 1, KEY_LEFTCTRL), /* SW5 */
333 KEY(2, 1, KEY_LEFT), /* (sw2/left) */
334 KEY(0, 2, KEY_SPACE), /* SW3 */
335 KEY(1, 2, KEY_ESC), /* SW6 */
336 KEY(2, 2, KEY_DOWN), /* (sw2/down) */
337 KEY(2, 3, KEY_ENTER), /* (sw2/select) */
338 KEY(3, 3, KEY_RIGHT), /* (sw2/right) */
339};
340
341static const struct matrix_keymap_data osk_keymap_data = {
342 .keymap = osk_keymap,
343 .keymap_size = ARRAY_SIZE(osk_keymap),
344};
345
346static struct omap_kp_platform_data osk_kp_data = {
347 .rows = 8,
348 .cols = 8,
349 .keymap_data = &osk_keymap_data,
350 .delay = 9,
351};
352
353static struct resource osk5912_kp_resources[] = {
354 [0] = {
355 .start = INT_KEYBOARD,
356 .end = INT_KEYBOARD,
357 .flags = IORESOURCE_IRQ,
358 },
359};
360
361static struct platform_device osk5912_kp_device = {
362 .name = "omap-keypad",
363 .id = -1,
364 .dev = {
365 .platform_data = &osk_kp_data,
366 },
367 .num_resources = ARRAY_SIZE(osk5912_kp_resources),
368 .resource = osk5912_kp_resources,
369};
370
371static struct omap_backlight_config mistral_bl_data = {
372 .default_intensity = 0xa0,
373};
374
375static struct platform_device mistral_bl_device = {
376 .name = "omap-bl",
377 .id = -1,
378 .dev = {
379 .platform_data = &mistral_bl_data,
380 },
381};
382
383static struct platform_device osk5912_lcd_device = {
384 .name = "lcd_osk",
385 .id = -1,
386};
387
388static struct gpio_led mistral_gpio_led_pins[] = {
389 {
390 .name = "mistral:red",
391 .default_trigger = "heartbeat",
392 .gpio = 3,
393 },
394 {
395 .name = "mistral:green",
396 .default_trigger = "cpu0",
397 .gpio = OMAP_MPUIO(4),
398 },
399};
400
401static struct gpio_led_platform_data mistral_gpio_led_data = {
402 .leds = mistral_gpio_led_pins,
403 .num_leds = ARRAY_SIZE(mistral_gpio_led_pins),
404};
405
406static struct platform_device mistral_gpio_leds = {
407 .name = "leds-gpio",
408 .id = -1,
409 .dev = {
410 .platform_data = &mistral_gpio_led_data,
411 },
412};
413
414static struct platform_device *mistral_devices[] __initdata = {
415 &osk5912_kp_device,
416 &mistral_bl_device,
417 &osk5912_lcd_device,
418 &mistral_gpio_leds,
419};
420
421static int mistral_get_pendown_state(void)
422{
423 return !gpio_get_value(4);
424}
425
426static const struct ads7846_platform_data mistral_ts_info = {
427 .model = 7846,
428 .vref_delay_usecs = 100, /* internal, no capacitor */
429 .x_plate_ohms = 419,
430 .y_plate_ohms = 486,
431 .get_pendown_state = mistral_get_pendown_state,
432};
433
434static struct spi_board_info __initdata mistral_boardinfo[] = { {
435 /* MicroWire (bus 2) CS0 has an ads7846e */
436 .modalias = "ads7846",
437 .platform_data = &mistral_ts_info,
438 .max_speed_hz = 120000 /* max sample rate at 3V */
439 * 26 /* command + data + overhead */,
440 .bus_num = 2,
441 .chip_select = 0,
442} };
443
444#ifdef CONFIG_PM
445static irqreturn_t
446osk_mistral_wake_interrupt(int irq, void *ignored)
447{
448 return IRQ_HANDLED;
449}
450#endif
451
452static void __init osk_mistral_init(void)
453{
454 /* NOTE: we could actually tell if there's a Mistral board
455 * attached, e.g. by trying to read something from the ads7846.
456 * But this arch_init() code is too early for that, since we
457 * can't talk to the ads or even the i2c eeprom.
458 */
459
460 /* parallel camera interface */
461 omap_cfg_reg(J15_1610_CAM_LCLK);
462 omap_cfg_reg(J18_1610_CAM_D7);
463 omap_cfg_reg(J19_1610_CAM_D6);
464 omap_cfg_reg(J14_1610_CAM_D5);
465 omap_cfg_reg(K18_1610_CAM_D4);
466 omap_cfg_reg(K19_1610_CAM_D3);
467 omap_cfg_reg(K15_1610_CAM_D2);
468 omap_cfg_reg(K14_1610_CAM_D1);
469 omap_cfg_reg(L19_1610_CAM_D0);
470 omap_cfg_reg(L18_1610_CAM_VS);
471 omap_cfg_reg(L15_1610_CAM_HS);
472 omap_cfg_reg(M19_1610_CAM_RSTZ);
473 omap_cfg_reg(Y15_1610_CAM_OUTCLK);
474
475 /* serial camera interface */
476 omap_cfg_reg(H19_1610_CAM_EXCLK);
477 omap_cfg_reg(W13_1610_CCP_CLKM);
478 omap_cfg_reg(Y12_1610_CCP_CLKP);
479 /* CCP_DATAM CONFLICTS WITH UART1.TX (and serial console) */
480 /* omap_cfg_reg(Y14_1610_CCP_DATAM); */
481 omap_cfg_reg(W14_1610_CCP_DATAP);
482
483 /* CAM_PWDN */
484 if (gpio_request(11, "cam_pwdn") == 0) {
485 omap_cfg_reg(N20_1610_GPIO11);
486 gpio_direction_output(11, 0);
487 } else
488 pr_debug("OSK+Mistral: CAM_PWDN is awol\n");
489
490
491 /* omap_cfg_reg(P19_1610_GPIO6); */ /* BUSY */
492 gpio_request(6, "ts_busy");
493 gpio_direction_input(6);
494
495 omap_cfg_reg(P20_1610_GPIO4); /* PENIRQ */
496 gpio_request(4, "ts_int");
497 gpio_direction_input(4);
498 irq_set_irq_type(gpio_to_irq(4), IRQ_TYPE_EDGE_FALLING);
499
500 mistral_boardinfo[0].irq = gpio_to_irq(4);
501 spi_register_board_info(mistral_boardinfo,
502 ARRAY_SIZE(mistral_boardinfo));
503
504 /* the sideways button (SW1) is for use as a "wakeup" button
505 *
506 * NOTE: The Mistral board has the wakeup button (SW1) wired
507 * to the LCD 3.3V rail, which is powered down during suspend.
508 * To allow this button to wake up the omap, work around this
509 * HW bug by rewiring SW1 to use the main 3.3V rail.
510 */
511 omap_cfg_reg(N15_1610_MPUIO2);
512 if (gpio_request(OMAP_MPUIO(2), "wakeup") == 0) {
513 int ret = 0;
514 int irq = gpio_to_irq(OMAP_MPUIO(2));
515
516 gpio_direction_input(OMAP_MPUIO(2));
517 irq_set_irq_type(irq, IRQ_TYPE_EDGE_RISING);
518#ifdef CONFIG_PM
519 /* share the IRQ in case someone wants to use the
520 * button for more than wakeup from system sleep.
521 */
522 ret = request_irq(irq,
523 &osk_mistral_wake_interrupt,
524 IRQF_SHARED, "mistral_wakeup",
525 &osk_mistral_wake_interrupt);
526 if (ret != 0) {
527 gpio_free(OMAP_MPUIO(2));
528 printk(KERN_ERR "OSK+Mistral: no wakeup irq, %d?\n",
529 ret);
530 } else
531 enable_irq_wake(irq);
532#endif
533 } else
534 printk(KERN_ERR "OSK+Mistral: wakeup button is awol\n");
535
536 /* LCD: backlight, and power; power controls other devices on the
537 * board, like the touchscreen, EEPROM, and wakeup (!) switch.
538 */
539 omap_cfg_reg(PWL);
540 if (gpio_request(2, "lcd_pwr") == 0)
541 gpio_direction_output(2, 1);
542
543 /*
544 * GPIO based LEDs
545 */
546 omap_cfg_reg(P18_1610_GPIO3);
547 omap_cfg_reg(MPUIO4);
548
549 i2c_register_board_info(1, mistral_i2c_board_info,
550 ARRAY_SIZE(mistral_i2c_board_info));
551
552 platform_add_devices(mistral_devices, ARRAY_SIZE(mistral_devices));
553}
554#else
555static void __init osk_mistral_init(void) { }
556#endif
557
558#define EMIFS_CS3_VAL (0x88013141)
559
560static void __init osk_init(void)
561{
562 u32 l;
563
564 osk_init_smc91x();
565 osk_init_cf();
566
567 /* Workaround for wrong CS3 (NOR flash) timing
568 * There are some U-Boot versions out there which configure
569 * wrong CS3 memory timings. This mainly leads to CRC
570 * or similar errors if you use NOR flash (e.g. with JFFS2)
571 */
572 l = omap_readl(EMIFS_CCS(3));
573 if (l != EMIFS_CS3_VAL)
574 omap_writel(EMIFS_CS3_VAL, EMIFS_CCS(3));
575
576 osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
577 osk_flash_resource.end += SZ_32M - 1;
578 osk5912_smc91x_resources[1].start = gpio_to_irq(0);
579 osk5912_smc91x_resources[1].end = gpio_to_irq(0);
580 osk5912_cf_resources[0].start = gpio_to_irq(62);
581 osk5912_cf_resources[0].end = gpio_to_irq(62);
582 platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
583
584 l = omap_readl(USB_TRANSCEIVER_CTRL);
585 l |= (3 << 1);
586 omap_writel(l, USB_TRANSCEIVER_CTRL);
587
588 omap1_usb_init(&osk_usb_config);
589
590 /* irq for tps65010 chip */
591 /* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
592 if (gpio_request(OMAP_MPUIO(1), "tps65010") == 0)
593 gpio_direction_input(OMAP_MPUIO(1));
594
595 omap_serial_init();
596 osk_i2c_board_info[0].irq = gpio_to_irq(OMAP_MPUIO(1));
597 omap_register_i2c_bus(1, 400, osk_i2c_board_info,
598 ARRAY_SIZE(osk_i2c_board_info));
599 osk_mistral_init();
600
601#ifdef CONFIG_OMAP_OSK_MISTRAL
602 omapfb_set_lcd_config(&osk_lcd_config);
603#endif
604
605}
606
607MACHINE_START(OMAP_OSK, "TI-OSK")
608 /* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
609 .atag_offset = 0x100,
610 .map_io = omap16xx_map_io,
611 .init_early = omap1_init_early,
612 .init_irq = omap1_init_irq,
613 .init_machine = osk_init,
614 .init_late = omap1_init_late,
615 .init_time = omap1_timer_init,
616 .restart = omap1_restart,
617MACHINE_END
1/*
2 * linux/arch/arm/mach-omap1/board-osk.c
3 *
4 * Board specific init for OMAP5912 OSK
5 *
6 * Written by Dirk Behme <dirk.behme@de.bosch.com>
7 *
8 * This program is free software; you can redistribute it and/or modify it
9 * under the terms of the GNU General Public License as published by the
10 * Free Software Foundation; either version 2 of the License, or (at your
11 * option) any later version.
12 *
13 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
14 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
15 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
16 * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
17 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
18 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
19 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
20 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
21 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
22 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
23 *
24 * You should have received a copy of the GNU General Public License along
25 * with this program; if not, write to the Free Software Foundation, Inc.,
26 * 675 Mass Ave, Cambridge, MA 02139, USA.
27 */
28#include <linux/gpio/consumer.h>
29#include <linux/gpio/driver.h>
30#include <linux/gpio/machine.h>
31#include <linux/kernel.h>
32#include <linux/init.h>
33#include <linux/platform_device.h>
34#include <linux/interrupt.h>
35#include <linux/irq.h>
36#include <linux/i2c.h>
37#include <linux/leds.h>
38#include <linux/smc91x.h>
39#include <linux/omapfb.h>
40#include <linux/mtd/mtd.h>
41#include <linux/mtd/partitions.h>
42#include <linux/mtd/physmap.h>
43#include <linux/mfd/tps65010.h>
44#include <linux/platform_data/gpio-omap.h>
45#include <linux/platform_data/omap1_bl.h>
46#include <linux/soc/ti/omap1-io.h>
47
48#include <asm/mach-types.h>
49#include <asm/mach/arch.h>
50#include <asm/mach/map.h>
51
52#include "tc.h"
53#include "flash.h"
54#include "mux.h"
55#include "hardware.h"
56#include "usb.h"
57#include "common.h"
58
59/* Name of the GPIO chip used by the OMAP for GPIOs 0..15 */
60#define OMAP_GPIO_LABEL "gpio-0-15"
61
62/* At OMAP5912 OSK the Ethernet is directly connected to CS1 */
63#define OMAP_OSK_ETHR_START 0x04800300
64
65/* TPS65010 has four GPIOs. nPG and LED2 can be treated like GPIOs with
66 * alternate pin configurations for hardware-controlled blinking.
67 */
68#define OSK_TPS_GPIO_USB_PWR_EN 0
69#define OSK_TPS_GPIO_LED_D3 1
70#define OSK_TPS_GPIO_LAN_RESET 2
71#define OSK_TPS_GPIO_DSP_PWR_EN 3
72#define OSK_TPS_GPIO_LED_D9 4
73#define OSK_TPS_GPIO_LED_D2 5
74
75static struct mtd_partition osk_partitions[] = {
76 /* bootloader (U-Boot, etc) in first sector */
77 {
78 .name = "bootloader",
79 .offset = 0,
80 .size = SZ_128K,
81 .mask_flags = MTD_WRITEABLE, /* force read-only */
82 },
83 /* bootloader params in the next sector */
84 {
85 .name = "params",
86 .offset = MTDPART_OFS_APPEND,
87 .size = SZ_128K,
88 .mask_flags = 0,
89 }, {
90 .name = "kernel",
91 .offset = MTDPART_OFS_APPEND,
92 .size = SZ_2M,
93 .mask_flags = 0
94 }, {
95 .name = "filesystem",
96 .offset = MTDPART_OFS_APPEND,
97 .size = MTDPART_SIZ_FULL,
98 .mask_flags = 0
99 }
100};
101
102static struct physmap_flash_data osk_flash_data = {
103 .width = 2,
104 .set_vpp = omap1_set_vpp,
105 .parts = osk_partitions,
106 .nr_parts = ARRAY_SIZE(osk_partitions),
107};
108
109static struct resource osk_flash_resource = {
110 /* this is on CS3, wherever it's mapped */
111 .flags = IORESOURCE_MEM,
112};
113
114static struct platform_device osk5912_flash_device = {
115 .name = "physmap-flash",
116 .id = 0,
117 .dev = {
118 .platform_data = &osk_flash_data,
119 },
120 .num_resources = 1,
121 .resource = &osk_flash_resource,
122};
123
124static struct smc91x_platdata osk5912_smc91x_info = {
125 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
126 .leda = RPC_LED_100_10,
127 .ledb = RPC_LED_TX_RX,
128};
129
130static struct resource osk5912_smc91x_resources[] = {
131 [0] = {
132 .start = OMAP_OSK_ETHR_START, /* Physical */
133 .end = OMAP_OSK_ETHR_START + 0xf,
134 .flags = IORESOURCE_MEM,
135 },
136 [1] = {
137 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
138 },
139};
140
141static struct platform_device osk5912_smc91x_device = {
142 .name = "smc91x",
143 .id = -1,
144 .dev = {
145 .platform_data = &osk5912_smc91x_info,
146 },
147 .num_resources = ARRAY_SIZE(osk5912_smc91x_resources),
148 .resource = osk5912_smc91x_resources,
149};
150
151static struct resource osk5912_cf_resources[] = {
152 [0] = {
153 .flags = IORESOURCE_IRQ,
154 },
155 [1] = {
156 .flags = IORESOURCE_MEM,
157 },
158};
159
160static struct platform_device osk5912_cf_device = {
161 .name = "omap_cf",
162 .id = -1,
163 .num_resources = ARRAY_SIZE(osk5912_cf_resources),
164 .resource = osk5912_cf_resources,
165};
166
167static struct platform_device *osk5912_devices[] __initdata = {
168 &osk5912_flash_device,
169 &osk5912_smc91x_device,
170 &osk5912_cf_device,
171};
172
173static const struct gpio_led tps_leds[] = {
174 /* NOTE: D9 and D2 have hardware blink support.
175 * Also, D9 requires non-battery power.
176 */
177 { .name = "d9", .default_trigger = "disk-activity", },
178 { .name = "d2", },
179 { .name = "d3", .default_trigger = "heartbeat", },
180};
181
182static struct gpiod_lookup_table tps_leds_gpio_table = {
183 .dev_id = "leds-gpio",
184 .table = {
185 /* Use local offsets on TPS65010 */
186 GPIO_LOOKUP_IDX("tps65010", OSK_TPS_GPIO_LED_D9, NULL, 0, GPIO_ACTIVE_HIGH),
187 GPIO_LOOKUP_IDX("tps65010", OSK_TPS_GPIO_LED_D2, NULL, 1, GPIO_ACTIVE_HIGH),
188 GPIO_LOOKUP_IDX("tps65010", OSK_TPS_GPIO_LED_D3, NULL, 2, GPIO_ACTIVE_LOW),
189 { }
190 },
191};
192
193static struct gpio_led_platform_data tps_leds_data = {
194 .num_leds = 3,
195 .leds = tps_leds,
196};
197
198static struct platform_device osk5912_tps_leds = {
199 .name = "leds-gpio",
200 .id = 0,
201 .dev.platform_data = &tps_leds_data,
202};
203
204/* The board just hold these GPIOs hogged from setup to teardown */
205static struct gpio_desc *eth_reset;
206static struct gpio_desc *vdd_dsp;
207
208static int osk_tps_setup(struct i2c_client *client, struct gpio_chip *gc)
209{
210 struct gpio_desc *d;
211 if (!IS_BUILTIN(CONFIG_TPS65010))
212 return -ENOSYS;
213
214 /* Set GPIO 1 HIGH to disable VBUS power supply;
215 * OHCI driver powers it up/down as needed.
216 */
217 d = gpiochip_request_own_desc(gc, OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en",
218 GPIO_ACTIVE_HIGH, GPIOD_OUT_HIGH);
219 /* Free the GPIO again as the driver will request it */
220 gpiochip_free_own_desc(d);
221
222 /* Set GPIO 2 high so LED D3 is off by default */
223 tps65010_set_gpio_out_value(GPIO2, HIGH);
224
225 /* Set GPIO 3 low to take ethernet out of reset */
226 eth_reset = gpiochip_request_own_desc(gc, OSK_TPS_GPIO_LAN_RESET, "smc_reset",
227 GPIO_ACTIVE_HIGH, GPIOD_OUT_LOW);
228
229 /* GPIO4 is VDD_DSP */
230 vdd_dsp = gpiochip_request_own_desc(gc, OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power",
231 GPIO_ACTIVE_HIGH, GPIOD_OUT_HIGH);
232 /* REVISIT if DSP support isn't configured, power it off ... */
233
234 /* Let LED1 (D9) blink; leds-gpio may override it */
235 tps65010_set_led(LED1, BLINK);
236
237 /* Set LED2 off by default */
238 tps65010_set_led(LED2, OFF);
239
240 /* Enable LOW_PWR handshake */
241 tps65010_set_low_pwr(ON);
242
243 /* Switch VLDO2 to 3.0V for AIC23 */
244 tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
245 | TPS_LDO1_ENABLE);
246
247 /* register these three LEDs */
248 osk5912_tps_leds.dev.parent = &client->dev;
249 gpiod_add_lookup_table(&tps_leds_gpio_table);
250 platform_device_register(&osk5912_tps_leds);
251
252 return 0;
253}
254
255static void osk_tps_teardown(struct i2c_client *client, struct gpio_chip *gc)
256{
257 gpiochip_free_own_desc(eth_reset);
258 gpiochip_free_own_desc(vdd_dsp);
259}
260
261static struct tps65010_board tps_board = {
262 .outmask = 0x0f,
263 .setup = osk_tps_setup,
264 .teardown = osk_tps_teardown,
265};
266
267static struct i2c_board_info __initdata osk_i2c_board_info[] = {
268 {
269 /* This device will get the name "i2c-tps65010" */
270 I2C_BOARD_INFO("tps65010", 0x48),
271 .dev_name = "tps65010",
272 .platform_data = &tps_board,
273
274 },
275 {
276 I2C_BOARD_INFO("tlv320aic23", 0x1B),
277 },
278 /* TODO when driver support is ready:
279 * - optionally on Mistral, ov9640 camera sensor at 0x30
280 */
281};
282
283static void __init osk_init_smc91x(void)
284{
285 u32 l;
286
287 /* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
288 l = omap_readl(EMIFS_CCS(1));
289 l |= 0x3;
290 omap_writel(l, EMIFS_CCS(1));
291}
292
293static void __init osk_init_cf(int seg)
294{
295 struct resource *res = &osk5912_cf_resources[1];
296
297 omap_cfg_reg(M7_1610_GPIO62);
298
299 switch (seg) {
300 /* NOTE: CS0 could be configured too ... */
301 case 1:
302 res->start = OMAP_CS1_PHYS;
303 break;
304 case 2:
305 res->start = OMAP_CS2_PHYS;
306 break;
307 case 3:
308 res->start = omap_cs3_phys();
309 break;
310 }
311
312 res->end = res->start + SZ_8K - 1;
313 osk5912_cf_device.dev.platform_data = (void *)(uintptr_t)seg;
314
315 /* NOTE: better EMIFS setup might support more cards; but the
316 * TRM only shows how to affect regular flash signals, not their
317 * CF/PCMCIA variants...
318 */
319 pr_debug("%s: cs%d, previous ccs %08x acs %08x\n", __func__,
320 seg, omap_readl(EMIFS_CCS(seg)), omap_readl(EMIFS_ACS(seg)));
321 omap_writel(0x0004a1b3, EMIFS_CCS(seg)); /* synch mode 4 etc */
322 omap_writel(0x00000000, EMIFS_ACS(seg)); /* OE hold/setup */
323}
324
325static struct gpiod_lookup_table osk_usb_gpio_table = {
326 .dev_id = "ohci",
327 .table = {
328 /* Power GPIO on the I2C-attached TPS65010 */
329 GPIO_LOOKUP("tps65010", OSK_TPS_GPIO_USB_PWR_EN, "power",
330 GPIO_ACTIVE_HIGH),
331 GPIO_LOOKUP(OMAP_GPIO_LABEL, 9, "overcurrent",
332 GPIO_ACTIVE_HIGH),
333 { }
334 },
335};
336
337static struct omap_usb_config osk_usb_config __initdata = {
338 /* has usb host connector (A) ... for development it can also
339 * be used, with a NONSTANDARD gender-bending cable/dongle, as
340 * a peripheral.
341 */
342#if IS_ENABLED(CONFIG_USB_OMAP)
343 .register_dev = 1,
344 .hmc_mode = 0,
345#else
346 .register_host = 1,
347 .hmc_mode = 16,
348 .rwc = 1,
349#endif
350 .pins[0] = 2,
351};
352
353#define EMIFS_CS3_VAL (0x88013141)
354
355static struct gpiod_lookup_table osk_irq_gpio_table = {
356 .dev_id = NULL,
357 .table = {
358 /* GPIO used for SMC91x IRQ */
359 GPIO_LOOKUP(OMAP_GPIO_LABEL, 0, "smc_irq",
360 GPIO_ACTIVE_HIGH),
361 /* GPIO used for CF IRQ */
362 GPIO_LOOKUP("gpio-48-63", 14, "cf_irq",
363 GPIO_ACTIVE_HIGH),
364 /* GPIO used by the TPS65010 chip */
365 GPIO_LOOKUP("mpuio", 1, "tps65010",
366 GPIO_ACTIVE_HIGH),
367 /* GPIOs used for serial wakeup IRQs */
368 GPIO_LOOKUP_IDX("gpio-32-47", 5, "wakeup", 0,
369 GPIO_ACTIVE_HIGH),
370 GPIO_LOOKUP_IDX("gpio-16-31", 2, "wakeup", 1,
371 GPIO_ACTIVE_HIGH),
372 GPIO_LOOKUP_IDX("gpio-48-63", 1, "wakeup", 2,
373 GPIO_ACTIVE_HIGH),
374 { }
375 },
376};
377
378static void __init osk_init(void)
379{
380 struct gpio_desc *d;
381 u32 l;
382
383 osk_init_smc91x();
384 osk_init_cf(2); /* CS2 */
385
386 /* Workaround for wrong CS3 (NOR flash) timing
387 * There are some U-Boot versions out there which configure
388 * wrong CS3 memory timings. This mainly leads to CRC
389 * or similar errors if you use NOR flash (e.g. with JFFS2)
390 */
391 l = omap_readl(EMIFS_CCS(3));
392 if (l != EMIFS_CS3_VAL)
393 omap_writel(EMIFS_CS3_VAL, EMIFS_CCS(3));
394
395 osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
396 osk_flash_resource.end += SZ_32M - 1;
397
398 /*
399 * Add the GPIOs to be used as IRQs and immediately look them up
400 * to be passed as an IRQ resource. This is ugly but should work
401 * until the day we convert to device tree.
402 */
403 gpiod_add_lookup_table(&osk_irq_gpio_table);
404
405 d = gpiod_get(NULL, "smc_irq", GPIOD_IN);
406 if (IS_ERR(d)) {
407 pr_err("Unable to get SMC IRQ GPIO descriptor\n");
408 } else {
409 irq_set_irq_type(gpiod_to_irq(d), IRQ_TYPE_EDGE_RISING);
410 osk5912_smc91x_resources[1] = DEFINE_RES_IRQ(gpiod_to_irq(d));
411 }
412
413 d = gpiod_get(NULL, "cf_irq", GPIOD_IN);
414 if (IS_ERR(d)) {
415 pr_err("Unable to get CF IRQ GPIO descriptor\n");
416 } else {
417 /* the CF I/O IRQ is really active-low */
418 irq_set_irq_type(gpiod_to_irq(d), IRQ_TYPE_EDGE_FALLING);
419 osk5912_cf_resources[0] = DEFINE_RES_IRQ(gpiod_to_irq(d));
420 }
421
422 platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
423
424 l = omap_readl(USB_TRANSCEIVER_CTRL);
425 l |= (3 << 1);
426 omap_writel(l, USB_TRANSCEIVER_CTRL);
427
428 gpiod_add_lookup_table(&osk_usb_gpio_table);
429 omap1_usb_init(&osk_usb_config);
430
431 omap_serial_init();
432
433 /* irq for tps65010 chip */
434 /* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
435 d = gpiod_get(NULL, "tps65010", GPIOD_IN);
436 if (IS_ERR(d))
437 pr_err("Unable to get TPS65010 IRQ GPIO descriptor\n");
438 else
439 osk_i2c_board_info[0].irq = gpiod_to_irq(d);
440 omap_register_i2c_bus(1, 400, osk_i2c_board_info,
441 ARRAY_SIZE(osk_i2c_board_info));
442}
443
444MACHINE_START(OMAP_OSK, "TI-OSK")
445 /* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
446 .atag_offset = 0x100,
447 .map_io = omap1_map_io,
448 .init_early = omap1_init_early,
449 .init_irq = omap1_init_irq,
450 .init_machine = osk_init,
451 .init_late = omap1_init_late,
452 .init_time = omap1_timer_init,
453 .restart = omap1_restart,
454MACHINE_END