Loading...
1#ifndef CYPRESS_M8_H
2#define CYPRESS_M8_H
3
4/*
5 * definitions and function prototypes used for the cypress USB to Serial
6 * controller
7 */
8
9/*
10 * For sending our feature buffer - controlling serial communication states.
11 * Linux HID has no support for serial devices so we do this through the driver
12 */
13#define HID_REQ_GET_REPORT 0x01
14#define HID_REQ_SET_REPORT 0x09
15
16/* List other cypress USB to Serial devices here, and add them to the id_table */
17
18/* DeLorme Earthmate USB - a GPS device */
19#define VENDOR_ID_DELORME 0x1163
20#define PRODUCT_ID_EARTHMATEUSB 0x0100
21#define PRODUCT_ID_EARTHMATEUSB_LT20 0x0200
22
23/* Cypress HID->COM RS232 Adapter */
24#define VENDOR_ID_CYPRESS 0x04b4
25#define PRODUCT_ID_CYPHIDCOM 0x5500
26
27/* Powercom UPS, chip CY7C63723 */
28#define VENDOR_ID_POWERCOM 0x0d9f
29#define PRODUCT_ID_UPS 0x0002
30
31/* Nokia CA-42 USB to serial cable */
32#define VENDOR_ID_DAZZLE 0x07d0
33#define PRODUCT_ID_CA42 0x4101
34/* End of device listing */
35
36/* Used for setting / requesting serial line settings */
37#define CYPRESS_SET_CONFIG 0x01
38#define CYPRESS_GET_CONFIG 0x02
39
40/* Used for throttle control */
41#define THROTTLED 0x1
42#define ACTUALLY_THROTTLED 0x2
43
44/*
45 * chiptypes - used in case firmware differs from the generic form ... offering
46 * different baud speeds/etc.
47 */
48#define CT_EARTHMATE 0x01
49#define CT_CYPHIDCOM 0x02
50#define CT_CA42V2 0x03
51#define CT_GENERIC 0x0F
52/* End of chiptype definitions */
53
54/* RS-232 serial data communication protocol definitions */
55/* these are sent / read at byte 0 of the input/output hid reports */
56/* You can find these values defined in the CY4601 USB to Serial design notes */
57
58#define CONTROL_DTR 0x20 /* data terminal ready - flow control - host to device */
59#define UART_DSR 0x20 /* data set ready - flow control - device to host */
60#define CONTROL_RTS 0x10 /* request to send - flow control - host to device */
61#define UART_CTS 0x10 /* clear to send - flow control - device to host */
62#define UART_RI 0x10 /* ring indicator - modem - device to host */
63#define UART_CD 0x40 /* carrier detect - modem - device to host */
64#define CYP_ERROR 0x08 /* received from input report - device to host */
65/* Note - the below has nothing to do with the "feature report" reset */
66#define CONTROL_RESET 0x08 /* sent with output report - host to device */
67
68/* End of RS-232 protocol definitions */
69
70#endif /* CYPRESS_M8_H */
1/* SPDX-License-Identifier: GPL-2.0 */
2#ifndef CYPRESS_M8_H
3#define CYPRESS_M8_H
4
5/*
6 * definitions and function prototypes used for the cypress USB to Serial
7 * controller
8 */
9
10/*
11 * For sending our feature buffer - controlling serial communication states.
12 * Linux HID has no support for serial devices so we do this through the driver
13 */
14#define HID_REQ_GET_REPORT 0x01
15#define HID_REQ_SET_REPORT 0x09
16
17/* List other cypress USB to Serial devices here, and add them to the id_table */
18
19/* DeLorme Earthmate USB - a GPS device */
20#define VENDOR_ID_DELORME 0x1163
21#define PRODUCT_ID_EARTHMATEUSB 0x0100
22#define PRODUCT_ID_EARTHMATEUSB_LT20 0x0200
23
24/* Cypress HID->COM RS232 Adapter */
25#define VENDOR_ID_CYPRESS 0x04b4
26#define PRODUCT_ID_CYPHIDCOM 0x5500
27
28/* FRWD Dongle - a GPS sports watch */
29#define VENDOR_ID_FRWD 0x6737
30#define PRODUCT_ID_CYPHIDCOM_FRWD 0x0001
31
32/* Powercom UPS, chip CY7C63723 */
33#define VENDOR_ID_POWERCOM 0x0d9f
34#define PRODUCT_ID_UPS 0x0002
35
36/* Nokia CA-42 USB to serial cable */
37#define VENDOR_ID_DAZZLE 0x07d0
38#define PRODUCT_ID_CA42 0x4101
39/* End of device listing */
40
41/* Used for setting / requesting serial line settings */
42#define CYPRESS_SET_CONFIG 0x01
43#define CYPRESS_GET_CONFIG 0x02
44
45/* Used for throttle control */
46#define THROTTLED 0x1
47#define ACTUALLY_THROTTLED 0x2
48
49/*
50 * chiptypes - used in case firmware differs from the generic form ... offering
51 * different baud speeds/etc.
52 */
53#define CT_EARTHMATE 0x01
54#define CT_CYPHIDCOM 0x02
55#define CT_CA42V2 0x03
56#define CT_GENERIC 0x0F
57/* End of chiptype definitions */
58
59/*
60 * RS-232 serial data communication protocol definitions.
61 *
62 * These are sent / read at byte 0 of the input/output hid reports.
63 * You can find these values defined in the CY4601 USB to Serial design notes.
64 */
65
66#define CONTROL_DTR 0x20 /* data terminal ready */
67#define CONTROL_RTS 0x10 /* request to send */
68#define CONTROL_RESET 0x08 /* sent with output report */
69
70#define UART_MSR_MASK 0xf0
71#define UART_RI 0x80 /* ring indicator */
72#define UART_CD 0x40 /* carrier detect */
73#define UART_DSR 0x20 /* data set ready */
74#define UART_CTS 0x10 /* clear to send */
75#define CYP_ERROR 0x08 /* received from input report */
76
77/* End of RS-232 protocol definitions */
78
79#endif /* CYPRESS_M8_H */