Loading...
1#define AUTOSENSE
2#define PSEUDO_DMA
3
4/*
5 * Trantor T128/T128F/T228 driver
6 * Note : architecturally, the T100 and T130 are different and won't
7 * work
8 *
9 * Copyright 1993, Drew Eckhardt
10 * Visionary Computing
11 * (Unix and Linux consulting and custom programming)
12 * drew@colorado.edu
13 * +1 (303) 440-4894
14 *
15 * DISTRIBUTION RELEASE 3.
16 *
17 * For more information, please consult
18 *
19 * Trantor Systems, Ltd.
20 * T128/T128F/T228 SCSI Host Adapter
21 * Hardware Specifications
22 *
23 * Trantor Systems, Ltd.
24 * 5415 Randall Place
25 * Fremont, CA 94538
26 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910
27 *
28 * and
29 *
30 * NCR 5380 Family
31 * SCSI Protocol Controller
32 * Databook
33 *
34 * NCR Microelectronics
35 * 1635 Aeroplaza Drive
36 * Colorado Springs, CO 80916
37 * 1+ (719) 578-3400
38 * 1+ (800) 334-5454
39 */
40
41/*
42 * Options :
43 * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
44 * for commands that return with a CHECK CONDITION status.
45 *
46 * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
47 * increase compared to polled I/O.
48 *
49 * PARITY - enable parity checking. Not supported.
50 *
51 * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
52 *
53 *
54 * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. You
55 * only really want to use this if you're having a problem with
56 * dropped characters during high speed communications, and even
57 * then, you're going to be better off twiddling with transfersize.
58 *
59 * USLEEP - enable support for devices that don't disconnect. Untested.
60 *
61 * The card is detected and initialized in one of several ways :
62 * 1. Autoprobe (default) - since the board is memory mapped,
63 * a BIOS signature is scanned for to locate the registers.
64 * An interrupt is triggered to autoprobe for the interrupt
65 * line.
66 *
67 * 2. With command line overrides - t128=address,irq may be
68 * used on the LILO command line to override the defaults.
69 *
70 * 3. With the T128_OVERRIDE compile time define. This is
71 * specified as an array of address, irq tuples. Ie, for
72 * one board at the default 0xcc000 address, IRQ5, I could say
73 * -DT128_OVERRIDE={{0xcc000, 5}}
74 *
75 * Note that if the override methods are used, place holders must
76 * be specified for other boards in the system.
77 *
78 * T128/T128F jumper/dipswitch settings (note : on my sample, the switches
79 * were epoxy'd shut, meaning I couldn't change the 0xcc000 base address) :
80 *
81 * T128 Sw7 Sw8 Sw6 = 0ws Sw5 = boot
82 * T128F Sw6 Sw7 Sw5 = 0ws Sw4 = boot Sw8 = floppy disable
83 * cc000 off off
84 * c8000 off on
85 * dc000 on off
86 * d8000 on on
87 *
88 *
89 * Interrupts
90 * There is a 12 pin jumper block, jp1, numbered as follows :
91 * T128 (JP1) T128F (J5)
92 * 2 4 6 8 10 12 11 9 7 5 3 1
93 * 1 3 5 7 9 11 12 10 8 6 4 2
94 *
95 * 3 2-4
96 * 5 1-3
97 * 7 3-5
98 * T128F only
99 * 10 8-10
100 * 12 7-9
101 * 14 10-12
102 * 15 9-11
103 */
104
105/*
106 * $Log: t128.c,v $
107 */
108
109#include <asm/system.h>
110#include <linux/signal.h>
111#include <linux/io.h>
112#include <linux/blkdev.h>
113#include <linux/interrupt.h>
114#include <linux/stat.h>
115#include <linux/init.h>
116#include <linux/module.h>
117#include <linux/delay.h>
118
119#include "scsi.h"
120#include <scsi/scsi_host.h>
121#include "t128.h"
122#define AUTOPROBE_IRQ
123#include "NCR5380.h"
124
125static struct override {
126 unsigned long address;
127 int irq;
128} overrides
129#ifdef T128_OVERRIDE
130 [] __initdata = T128_OVERRIDE;
131#else
132 [4] __initdata = {{0, IRQ_AUTO}, {0, IRQ_AUTO},
133 {0 ,IRQ_AUTO}, {0, IRQ_AUTO}};
134#endif
135
136#define NO_OVERRIDES ARRAY_SIZE(overrides)
137
138static struct base {
139 unsigned int address;
140 int noauto;
141} bases[] __initdata = {
142 { 0xcc000, 0}, { 0xc8000, 0}, { 0xdc000, 0}, { 0xd8000, 0}
143};
144
145#define NO_BASES ARRAY_SIZE(bases)
146
147static struct signature {
148 const char *string;
149 int offset;
150} signatures[] __initdata = {
151{"TSROM: SCSI BIOS, Version 1.12", 0x36},
152};
153
154#define NO_SIGNATURES ARRAY_SIZE(signatures)
155
156/*
157 * Function : t128_setup(char *str, int *ints)
158 *
159 * Purpose : LILO command line initialization of the overrides array,
160 *
161 * Inputs : str - unused, ints - array of integer parameters with ints[0]
162 * equal to the number of ints.
163 *
164 */
165
166void __init t128_setup(char *str, int *ints){
167 static int commandline_current = 0;
168 int i;
169 if (ints[0] != 2)
170 printk("t128_setup : usage t128=address,irq\n");
171 else
172 if (commandline_current < NO_OVERRIDES) {
173 overrides[commandline_current].address = ints[1];
174 overrides[commandline_current].irq = ints[2];
175 for (i = 0; i < NO_BASES; ++i)
176 if (bases[i].address == ints[1]) {
177 bases[i].noauto = 1;
178 break;
179 }
180 ++commandline_current;
181 }
182}
183
184/*
185 * Function : int t128_detect(struct scsi_host_template * tpnt)
186 *
187 * Purpose : detects and initializes T128,T128F, or T228 controllers
188 * that were autoprobed, overridden on the LILO command line,
189 * or specified at compile time.
190 *
191 * Inputs : tpnt - template for this SCSI adapter.
192 *
193 * Returns : 1 if a host adapter was found, 0 if not.
194 *
195 */
196
197int __init t128_detect(struct scsi_host_template * tpnt){
198 static int current_override = 0, current_base = 0;
199 struct Scsi_Host *instance;
200 unsigned long base;
201 void __iomem *p;
202 int sig, count;
203
204 tpnt->proc_name = "t128";
205 tpnt->proc_info = &t128_proc_info;
206
207 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
208 base = 0;
209 p = NULL;
210
211 if (overrides[current_override].address) {
212 base = overrides[current_override].address;
213 p = ioremap(bases[current_base].address, 0x2000);
214 if (!p)
215 base = 0;
216 } else
217 for (; !base && (current_base < NO_BASES); ++current_base) {
218#if (TDEBUG & TDEBUG_INIT)
219 printk("scsi-t128 : probing address %08x\n", bases[current_base].address);
220#endif
221 if (bases[current_base].noauto)
222 continue;
223 p = ioremap(bases[current_base].address, 0x2000);
224 if (!p)
225 continue;
226 for (sig = 0; sig < NO_SIGNATURES; ++sig)
227 if (check_signature(p + signatures[sig].offset,
228 signatures[sig].string,
229 strlen(signatures[sig].string))) {
230 base = bases[current_base].address;
231#if (TDEBUG & TDEBUG_INIT)
232 printk("scsi-t128 : detected board.\n");
233#endif
234 goto found;
235 }
236 iounmap(p);
237 }
238
239#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
240 printk("scsi-t128 : base = %08x\n", (unsigned int) base);
241#endif
242
243 if (!base)
244 break;
245
246found:
247 instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
248 if(instance == NULL)
249 break;
250
251 instance->base = base;
252 ((struct NCR5380_hostdata *)instance->hostdata)->base = p;
253
254 NCR5380_init(instance, 0);
255
256 if (overrides[current_override].irq != IRQ_AUTO)
257 instance->irq = overrides[current_override].irq;
258 else
259 instance->irq = NCR5380_probe_irq(instance, T128_IRQS);
260
261 if (instance->irq != SCSI_IRQ_NONE)
262 if (request_irq(instance->irq, t128_intr, IRQF_DISABLED, "t128",
263 instance)) {
264 printk("scsi%d : IRQ%d not free, interrupts disabled\n",
265 instance->host_no, instance->irq);
266 instance->irq = SCSI_IRQ_NONE;
267 }
268
269 if (instance->irq == SCSI_IRQ_NONE) {
270 printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
271 printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
272 }
273
274#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
275 printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
276#endif
277
278 printk("scsi%d : at 0x%08lx", instance->host_no, instance->base);
279 if (instance->irq == SCSI_IRQ_NONE)
280 printk (" interrupts disabled");
281 else
282 printk (" irq %d", instance->irq);
283 printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
284 CAN_QUEUE, CMD_PER_LUN, T128_PUBLIC_RELEASE);
285 NCR5380_print_options(instance);
286 printk("\n");
287
288 ++current_override;
289 ++count;
290 }
291 return count;
292}
293
294static int t128_release(struct Scsi_Host *shost)
295{
296 NCR5380_local_declare();
297 NCR5380_setup(shost);
298 if (shost->irq)
299 free_irq(shost->irq, shost);
300 NCR5380_exit(shost);
301 if (shost->io_port && shost->n_io_port)
302 release_region(shost->io_port, shost->n_io_port);
303 scsi_unregister(shost);
304 iounmap(base);
305 return 0;
306}
307
308/*
309 * Function : int t128_biosparam(Disk * disk, struct block_device *dev, int *ip)
310 *
311 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
312 * the specified device / size.
313 *
314 * Inputs : size = size of device in sectors (512 bytes), dev = block device
315 * major / minor, ip[] = {heads, sectors, cylinders}
316 *
317 * Returns : always 0 (success), initializes ip
318 *
319 */
320
321/*
322 * XXX Most SCSI boards use this mapping, I could be incorrect. Some one
323 * using hard disks on a trantor should verify that this mapping corresponds
324 * to that used by the BIOS / ASPI driver by running the linux fdisk program
325 * and matching the H_C_S coordinates to what DOS uses.
326 */
327
328int t128_biosparam(struct scsi_device *sdev, struct block_device *bdev,
329 sector_t capacity, int * ip)
330{
331 ip[0] = 64;
332 ip[1] = 32;
333 ip[2] = capacity >> 11;
334 return 0;
335}
336
337/*
338 * Function : int NCR5380_pread (struct Scsi_Host *instance,
339 * unsigned char *dst, int len)
340 *
341 * Purpose : Fast 5380 pseudo-dma read function, transfers len bytes to
342 * dst
343 *
344 * Inputs : dst = destination, len = length in bytes
345 *
346 * Returns : 0 on success, non zero on a failure such as a watchdog
347 * timeout.
348 */
349
350static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst,
351 int len) {
352 NCR5380_local_declare();
353 void __iomem *reg;
354 unsigned char *d = dst;
355 register int i = len;
356
357 NCR5380_setup(instance);
358 reg = base + T_DATA_REG_OFFSET;
359
360#if 0
361 for (; i; --i) {
362 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
363#else
364 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
365 for (; i; --i) {
366#endif
367 *d++ = readb(reg);
368 }
369
370 if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
371 unsigned char tmp;
372 void __iomem *foo = base + T_CONTROL_REG_OFFSET;
373 tmp = readb(foo);
374 writeb(tmp | T_CR_CT, foo);
375 writeb(tmp, foo);
376 printk("scsi%d : watchdog timer fired in NCR5380_pread()\n",
377 instance->host_no);
378 return -1;
379 } else
380 return 0;
381}
382
383/*
384 * Function : int NCR5380_pwrite (struct Scsi_Host *instance,
385 * unsigned char *src, int len)
386 *
387 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
388 * src
389 *
390 * Inputs : src = source, len = length in bytes
391 *
392 * Returns : 0 on success, non zero on a failure such as a watchdog
393 * timeout.
394 */
395
396static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src,
397 int len) {
398 NCR5380_local_declare();
399 void __iomem *reg;
400 unsigned char *s = src;
401 register int i = len;
402
403 NCR5380_setup(instance);
404 reg = base + T_DATA_REG_OFFSET;
405
406#if 0
407 for (; i; --i) {
408 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
409#else
410 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
411 for (; i; --i) {
412#endif
413 writeb(*s++, reg);
414 }
415
416 if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
417 unsigned char tmp;
418 void __iomem *foo = base + T_CONTROL_REG_OFFSET;
419 tmp = readb(foo);
420 writeb(tmp | T_CR_CT, foo);
421 writeb(tmp, foo);
422 printk("scsi%d : watchdog timer fired in NCR5380_pwrite()\n",
423 instance->host_no);
424 return -1;
425 } else
426 return 0;
427}
428
429MODULE_LICENSE("GPL");
430
431#include "NCR5380.c"
432
433static struct scsi_host_template driver_template = {
434 .name = "Trantor T128/T128F/T228",
435 .detect = t128_detect,
436 .release = t128_release,
437 .queuecommand = t128_queue_command,
438 .eh_abort_handler = t128_abort,
439 .eh_bus_reset_handler = t128_bus_reset,
440 .bios_param = t128_biosparam,
441 .can_queue = CAN_QUEUE,
442 .this_id = 7,
443 .sg_tablesize = SG_ALL,
444 .cmd_per_lun = CMD_PER_LUN,
445 .use_clustering = DISABLE_CLUSTERING,
446};
447#include "scsi_module.c"
1#define PSEUDO_DMA
2
3/*
4 * Trantor T128/T128F/T228 driver
5 * Note : architecturally, the T100 and T130 are different and won't
6 * work
7 *
8 * Copyright 1993, Drew Eckhardt
9 * Visionary Computing
10 * (Unix and Linux consulting and custom programming)
11 * drew@colorado.edu
12 * +1 (303) 440-4894
13 *
14 * For more information, please consult
15 *
16 * Trantor Systems, Ltd.
17 * T128/T128F/T228 SCSI Host Adapter
18 * Hardware Specifications
19 *
20 * Trantor Systems, Ltd.
21 * 5415 Randall Place
22 * Fremont, CA 94538
23 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910
24 */
25
26/*
27 * The card is detected and initialized in one of several ways :
28 * 1. Autoprobe (default) - since the board is memory mapped,
29 * a BIOS signature is scanned for to locate the registers.
30 * An interrupt is triggered to autoprobe for the interrupt
31 * line.
32 *
33 * 2. With command line overrides - t128=address,irq may be
34 * used on the LILO command line to override the defaults.
35 *
36 * 3. With the T128_OVERRIDE compile time define. This is
37 * specified as an array of address, irq tuples. Ie, for
38 * one board at the default 0xcc000 address, IRQ5, I could say
39 * -DT128_OVERRIDE={{0xcc000, 5}}
40 *
41 * Note that if the override methods are used, place holders must
42 * be specified for other boards in the system.
43 *
44 * T128/T128F jumper/dipswitch settings (note : on my sample, the switches
45 * were epoxy'd shut, meaning I couldn't change the 0xcc000 base address) :
46 *
47 * T128 Sw7 Sw8 Sw6 = 0ws Sw5 = boot
48 * T128F Sw6 Sw7 Sw5 = 0ws Sw4 = boot Sw8 = floppy disable
49 * cc000 off off
50 * c8000 off on
51 * dc000 on off
52 * d8000 on on
53 *
54 *
55 * Interrupts
56 * There is a 12 pin jumper block, jp1, numbered as follows :
57 * T128 (JP1) T128F (J5)
58 * 2 4 6 8 10 12 11 9 7 5 3 1
59 * 1 3 5 7 9 11 12 10 8 6 4 2
60 *
61 * 3 2-4
62 * 5 1-3
63 * 7 3-5
64 * T128F only
65 * 10 8-10
66 * 12 7-9
67 * 14 10-12
68 * 15 9-11
69 */
70
71#include <linux/io.h>
72#include <linux/blkdev.h>
73#include <linux/interrupt.h>
74#include <linux/init.h>
75#include <linux/module.h>
76
77#include <scsi/scsi_host.h>
78#include "t128.h"
79#define AUTOPROBE_IRQ
80#include "NCR5380.h"
81
82static struct override {
83 unsigned long address;
84 int irq;
85} overrides
86#ifdef T128_OVERRIDE
87 [] __initdata = T128_OVERRIDE;
88#else
89 [4] __initdata = {{0, IRQ_AUTO}, {0, IRQ_AUTO},
90 {0 ,IRQ_AUTO}, {0, IRQ_AUTO}};
91#endif
92
93#define NO_OVERRIDES ARRAY_SIZE(overrides)
94
95static struct base {
96 unsigned int address;
97 int noauto;
98} bases[] __initdata = {
99 { 0xcc000, 0}, { 0xc8000, 0}, { 0xdc000, 0}, { 0xd8000, 0}
100};
101
102#define NO_BASES ARRAY_SIZE(bases)
103
104static struct signature {
105 const char *string;
106 int offset;
107} signatures[] __initdata = {
108{"TSROM: SCSI BIOS, Version 1.12", 0x36},
109};
110
111#define NO_SIGNATURES ARRAY_SIZE(signatures)
112
113#ifndef MODULE
114/*
115 * Function : t128_setup(char *str, int *ints)
116 *
117 * Purpose : LILO command line initialization of the overrides array,
118 *
119 * Inputs : str - unused, ints - array of integer parameters with ints[0]
120 * equal to the number of ints.
121 *
122 */
123
124static int __init t128_setup(char *str)
125{
126 static int commandline_current;
127 int i;
128 int ints[10];
129
130 get_options(str, ARRAY_SIZE(ints), ints);
131 if (ints[0] != 2)
132 printk("t128_setup : usage t128=address,irq\n");
133 else
134 if (commandline_current < NO_OVERRIDES) {
135 overrides[commandline_current].address = ints[1];
136 overrides[commandline_current].irq = ints[2];
137 for (i = 0; i < NO_BASES; ++i)
138 if (bases[i].address == ints[1]) {
139 bases[i].noauto = 1;
140 break;
141 }
142 ++commandline_current;
143 }
144 return 1;
145}
146
147__setup("t128=", t128_setup);
148#endif
149
150/*
151 * Function : int t128_detect(struct scsi_host_template * tpnt)
152 *
153 * Purpose : detects and initializes T128,T128F, or T228 controllers
154 * that were autoprobed, overridden on the LILO command line,
155 * or specified at compile time.
156 *
157 * Inputs : tpnt - template for this SCSI adapter.
158 *
159 * Returns : 1 if a host adapter was found, 0 if not.
160 *
161 */
162
163static int __init t128_detect(struct scsi_host_template *tpnt)
164{
165 static int current_override, current_base;
166 struct Scsi_Host *instance;
167 unsigned long base;
168 void __iomem *p;
169 int sig, count;
170
171 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
172 base = 0;
173 p = NULL;
174
175 if (overrides[current_override].address) {
176 base = overrides[current_override].address;
177 p = ioremap(bases[current_base].address, 0x2000);
178 if (!p)
179 base = 0;
180 } else
181 for (; !base && (current_base < NO_BASES); ++current_base) {
182 dprintk(NDEBUG_INIT, "t128: probing address 0x%08x\n",
183 bases[current_base].address);
184 if (bases[current_base].noauto)
185 continue;
186 p = ioremap(bases[current_base].address, 0x2000);
187 if (!p)
188 continue;
189 for (sig = 0; sig < NO_SIGNATURES; ++sig)
190 if (check_signature(p + signatures[sig].offset,
191 signatures[sig].string,
192 strlen(signatures[sig].string))) {
193 base = bases[current_base].address;
194 dprintk(NDEBUG_INIT, "t128: detected board\n");
195 goto found;
196 }
197 iounmap(p);
198 }
199
200 dprintk(NDEBUG_INIT, "t128: base = 0x%08x\n", (unsigned int)base);
201
202 if (!base)
203 break;
204
205found:
206 instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
207 if(instance == NULL)
208 goto out_unmap;
209
210 instance->base = base;
211 ((struct NCR5380_hostdata *)instance->hostdata)->base = p;
212
213 if (NCR5380_init(instance, 0))
214 goto out_unregister;
215
216 NCR5380_maybe_reset_bus(instance);
217
218 if (overrides[current_override].irq != IRQ_AUTO)
219 instance->irq = overrides[current_override].irq;
220 else
221 instance->irq = NCR5380_probe_irq(instance, T128_IRQS);
222
223 /* Compatibility with documented NCR5380 kernel parameters */
224 if (instance->irq == 255)
225 instance->irq = NO_IRQ;
226
227 if (instance->irq != NO_IRQ)
228 if (request_irq(instance->irq, t128_intr, 0, "t128",
229 instance)) {
230 printk("scsi%d : IRQ%d not free, interrupts disabled\n",
231 instance->host_no, instance->irq);
232 instance->irq = NO_IRQ;
233 }
234
235 if (instance->irq == NO_IRQ) {
236 printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
237 printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
238 }
239
240 dprintk(NDEBUG_INIT, "scsi%d: irq = %d\n",
241 instance->host_no, instance->irq);
242
243 ++current_override;
244 ++count;
245 }
246 return count;
247
248out_unregister:
249 scsi_unregister(instance);
250out_unmap:
251 iounmap(p);
252 return count;
253}
254
255static int t128_release(struct Scsi_Host *shost)
256{
257 struct NCR5380_hostdata *hostdata = shost_priv(shost);
258
259 if (shost->irq != NO_IRQ)
260 free_irq(shost->irq, shost);
261 NCR5380_exit(shost);
262 scsi_unregister(shost);
263 iounmap(hostdata->base);
264 return 0;
265}
266
267/*
268 * Function : int t128_biosparam(Disk * disk, struct block_device *dev, int *ip)
269 *
270 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
271 * the specified device / size.
272 *
273 * Inputs : size = size of device in sectors (512 bytes), dev = block device
274 * major / minor, ip[] = {heads, sectors, cylinders}
275 *
276 * Returns : always 0 (success), initializes ip
277 *
278 */
279
280/*
281 * XXX Most SCSI boards use this mapping, I could be incorrect. Some one
282 * using hard disks on a trantor should verify that this mapping corresponds
283 * to that used by the BIOS / ASPI driver by running the linux fdisk program
284 * and matching the H_C_S coordinates to what DOS uses.
285 */
286
287static int t128_biosparam(struct scsi_device *sdev, struct block_device *bdev,
288 sector_t capacity, int *ip)
289{
290 ip[0] = 64;
291 ip[1] = 32;
292 ip[2] = capacity >> 11;
293 return 0;
294}
295
296/*
297 * Function : int NCR5380_pread (struct Scsi_Host *instance,
298 * unsigned char *dst, int len)
299 *
300 * Purpose : Fast 5380 pseudo-dma read function, transfers len bytes to
301 * dst
302 *
303 * Inputs : dst = destination, len = length in bytes
304 *
305 * Returns : 0 on success, non zero on a failure such as a watchdog
306 * timeout.
307 */
308
309static inline int
310NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
311{
312 struct NCR5380_hostdata *hostdata = shost_priv(instance);
313 void __iomem *reg, *base = hostdata->base;
314 unsigned char *d = dst;
315 register int i = len;
316
317 reg = base + T_DATA_REG_OFFSET;
318
319#if 0
320 for (; i; --i) {
321 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
322#else
323 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
324 for (; i; --i) {
325#endif
326 *d++ = readb(reg);
327 }
328
329 if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
330 unsigned char tmp;
331 void __iomem *foo = base + T_CONTROL_REG_OFFSET;
332 tmp = readb(foo);
333 writeb(tmp | T_CR_CT, foo);
334 writeb(tmp, foo);
335 printk("scsi%d : watchdog timer fired in NCR5380_pread()\n",
336 instance->host_no);
337 return -1;
338 } else
339 return 0;
340}
341
342/*
343 * Function : int NCR5380_pwrite (struct Scsi_Host *instance,
344 * unsigned char *src, int len)
345 *
346 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
347 * src
348 *
349 * Inputs : src = source, len = length in bytes
350 *
351 * Returns : 0 on success, non zero on a failure such as a watchdog
352 * timeout.
353 */
354
355static inline int
356NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
357{
358 struct NCR5380_hostdata *hostdata = shost_priv(instance);
359 void __iomem *reg, *base = hostdata->base;
360 unsigned char *s = src;
361 register int i = len;
362
363 reg = base + T_DATA_REG_OFFSET;
364
365#if 0
366 for (; i; --i) {
367 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
368#else
369 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
370 for (; i; --i) {
371#endif
372 writeb(*s++, reg);
373 }
374
375 if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
376 unsigned char tmp;
377 void __iomem *foo = base + T_CONTROL_REG_OFFSET;
378 tmp = readb(foo);
379 writeb(tmp | T_CR_CT, foo);
380 writeb(tmp, foo);
381 printk("scsi%d : watchdog timer fired in NCR5380_pwrite()\n",
382 instance->host_no);
383 return -1;
384 } else
385 return 0;
386}
387
388MODULE_LICENSE("GPL");
389
390#include "NCR5380.c"
391
392static struct scsi_host_template driver_template = {
393 .name = "Trantor T128/T128F/T228",
394 .detect = t128_detect,
395 .release = t128_release,
396 .proc_name = "t128",
397 .show_info = t128_show_info,
398 .write_info = t128_write_info,
399 .info = t128_info,
400 .queuecommand = t128_queue_command,
401 .eh_abort_handler = t128_abort,
402 .eh_bus_reset_handler = t128_bus_reset,
403 .bios_param = t128_biosparam,
404 .can_queue = 32,
405 .this_id = 7,
406 .sg_tablesize = SG_ALL,
407 .cmd_per_lun = 2,
408 .use_clustering = DISABLE_CLUSTERING,
409 .cmd_size = NCR5380_CMD_SIZE,
410 .max_sectors = 128,
411};
412#include "scsi_module.c"