Linux Audio

Check our new training course

Loading...
Note: File does not exist in v3.1.
   1/*******************************************************************************
   2
   3  Intel 10 Gigabit PCI Express Linux driver
   4  Copyright(c) 1999 - 2015 Intel Corporation.
   5
   6  This program is free software; you can redistribute it and/or modify it
   7  under the terms and conditions of the GNU General Public License,
   8  version 2, as published by the Free Software Foundation.
   9
  10  This program is distributed in the hope it will be useful, but WITHOUT
  11  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  12  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  13  more details.
  14
  15  You should have received a copy of the GNU General Public License along with
  16  this program; if not, write to the Free Software Foundation, Inc.,
  17  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
  18
  19  The full GNU General Public License is included in this distribution in
  20  the file called "COPYING".
  21
  22  Contact Information:
  23  Linux NICS <linux.nics@intel.com>
  24  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
  25  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
  26
  27*******************************************************************************/
  28
  29#include <linux/types.h>
  30#include <linux/module.h>
  31#include <linux/pci.h>
  32#include <linux/netdevice.h>
  33#include <linux/vmalloc.h>
  34#include <linux/string.h>
  35#include <linux/in.h>
  36#include <linux/ip.h>
  37#include <linux/tcp.h>
  38#include <linux/ipv6.h>
  39#include <linux/if_bridge.h>
  40#ifdef NETIF_F_HW_VLAN_CTAG_TX
  41#include <linux/if_vlan.h>
  42#endif
  43
  44#include "ixgbe.h"
  45#include "ixgbe_type.h"
  46#include "ixgbe_sriov.h"
  47
  48#ifdef CONFIG_PCI_IOV
  49static int __ixgbe_enable_sriov(struct ixgbe_adapter *adapter)
  50{
  51	struct ixgbe_hw *hw = &adapter->hw;
  52	int num_vf_macvlans, i;
  53	struct vf_macvlans *mv_list;
  54
  55	adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED;
  56	e_info(probe, "SR-IOV enabled with %d VFs\n", adapter->num_vfs);
  57
  58	/* Enable VMDq flag so device will be set in VM mode */
  59	adapter->flags |= IXGBE_FLAG_VMDQ_ENABLED;
  60	if (!adapter->ring_feature[RING_F_VMDQ].limit)
  61		adapter->ring_feature[RING_F_VMDQ].limit = 1;
  62	adapter->ring_feature[RING_F_VMDQ].offset = adapter->num_vfs;
  63
  64	num_vf_macvlans = hw->mac.num_rar_entries -
  65	(IXGBE_MAX_PF_MACVLANS + 1 + adapter->num_vfs);
  66
  67	adapter->mv_list = mv_list = kcalloc(num_vf_macvlans,
  68					     sizeof(struct vf_macvlans),
  69					     GFP_KERNEL);
  70	if (mv_list) {
  71		/* Initialize list of VF macvlans */
  72		INIT_LIST_HEAD(&adapter->vf_mvs.l);
  73		for (i = 0; i < num_vf_macvlans; i++) {
  74			mv_list->vf = -1;
  75			mv_list->free = true;
  76			list_add(&mv_list->l, &adapter->vf_mvs.l);
  77			mv_list++;
  78		}
  79	}
  80
  81	/* Initialize default switching mode VEB */
  82	IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, IXGBE_PFDTXGSWC_VT_LBEN);
  83	adapter->bridge_mode = BRIDGE_MODE_VEB;
  84
  85	/* If call to enable VFs succeeded then allocate memory
  86	 * for per VF control structures.
  87	 */
  88	adapter->vfinfo =
  89		kcalloc(adapter->num_vfs,
  90			sizeof(struct vf_data_storage), GFP_KERNEL);
  91	if (adapter->vfinfo) {
  92		/* limit trafffic classes based on VFs enabled */
  93		if ((adapter->hw.mac.type == ixgbe_mac_82599EB) &&
  94		    (adapter->num_vfs < 16)) {
  95			adapter->dcb_cfg.num_tcs.pg_tcs = MAX_TRAFFIC_CLASS;
  96			adapter->dcb_cfg.num_tcs.pfc_tcs = MAX_TRAFFIC_CLASS;
  97		} else if (adapter->num_vfs < 32) {
  98			adapter->dcb_cfg.num_tcs.pg_tcs = 4;
  99			adapter->dcb_cfg.num_tcs.pfc_tcs = 4;
 100		} else {
 101			adapter->dcb_cfg.num_tcs.pg_tcs = 1;
 102			adapter->dcb_cfg.num_tcs.pfc_tcs = 1;
 103		}
 104
 105		/* Disable RSC when in SR-IOV mode */
 106		adapter->flags2 &= ~(IXGBE_FLAG2_RSC_CAPABLE |
 107				     IXGBE_FLAG2_RSC_ENABLED);
 108
 109		for (i = 0; i < adapter->num_vfs; i++) {
 110			/* enable spoof checking for all VFs */
 111			adapter->vfinfo[i].spoofchk_enabled = true;
 112
 113			/* We support VF RSS querying only for 82599 and x540
 114			 * devices at the moment. These devices share RSS
 115			 * indirection table and RSS hash key with PF therefore
 116			 * we want to disable the querying by default.
 117			 */
 118			adapter->vfinfo[i].rss_query_enabled = 0;
 119
 120			/* Untrust all VFs */
 121			adapter->vfinfo[i].trusted = false;
 122
 123			/* set the default xcast mode */
 124			adapter->vfinfo[i].xcast_mode = IXGBEVF_XCAST_MODE_NONE;
 125		}
 126
 127		return 0;
 128	}
 129
 130	return -ENOMEM;
 131}
 132
 133/**
 134 * ixgbe_get_vfs - Find and take references to all vf devices
 135 * @adapter: Pointer to adapter struct
 136 */
 137static void ixgbe_get_vfs(struct ixgbe_adapter *adapter)
 138{
 139	struct pci_dev *pdev = adapter->pdev;
 140	u16 vendor = pdev->vendor;
 141	struct pci_dev *vfdev;
 142	int vf = 0;
 143	u16 vf_id;
 144	int pos;
 145
 146	pos = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_SRIOV);
 147	if (!pos)
 148		return;
 149	pci_read_config_word(pdev, pos + PCI_SRIOV_VF_DID, &vf_id);
 150
 151	vfdev = pci_get_device(vendor, vf_id, NULL);
 152	for (; vfdev; vfdev = pci_get_device(vendor, vf_id, vfdev)) {
 153		if (!vfdev->is_virtfn)
 154			continue;
 155		if (vfdev->physfn != pdev)
 156			continue;
 157		if (vf >= adapter->num_vfs)
 158			continue;
 159		pci_dev_get(vfdev);
 160		adapter->vfinfo[vf].vfdev = vfdev;
 161		++vf;
 162	}
 163}
 164
 165/* Note this function is called when the user wants to enable SR-IOV
 166 * VFs using the now deprecated module parameter
 167 */
 168void ixgbe_enable_sriov(struct ixgbe_adapter *adapter)
 169{
 170	int pre_existing_vfs = 0;
 171
 172	pre_existing_vfs = pci_num_vf(adapter->pdev);
 173	if (!pre_existing_vfs && !adapter->num_vfs)
 174		return;
 175
 176	/* If there are pre-existing VFs then we have to force
 177	 * use of that many - over ride any module parameter value.
 178	 * This may result from the user unloading the PF driver
 179	 * while VFs were assigned to guest VMs or because the VFs
 180	 * have been created via the new PCI SR-IOV sysfs interface.
 181	 */
 182	if (pre_existing_vfs) {
 183		adapter->num_vfs = pre_existing_vfs;
 184		dev_warn(&adapter->pdev->dev,
 185			 "Virtual Functions already enabled for this device - Please reload all VF drivers to avoid spoofed packet errors\n");
 186	} else {
 187		int err;
 188		/*
 189		 * The 82599 supports up to 64 VFs per physical function
 190		 * but this implementation limits allocation to 63 so that
 191		 * basic networking resources are still available to the
 192		 * physical function.  If the user requests greater than
 193		 * 63 VFs then it is an error - reset to default of zero.
 194		 */
 195		adapter->num_vfs = min_t(unsigned int, adapter->num_vfs, IXGBE_MAX_VFS_DRV_LIMIT);
 196
 197		err = pci_enable_sriov(adapter->pdev, adapter->num_vfs);
 198		if (err) {
 199			e_err(probe, "Failed to enable PCI sriov: %d\n", err);
 200			adapter->num_vfs = 0;
 201			return;
 202		}
 203	}
 204
 205	if (!__ixgbe_enable_sriov(adapter)) {
 206		ixgbe_get_vfs(adapter);
 207		return;
 208	}
 209
 210	/* If we have gotten to this point then there is no memory available
 211	 * to manage the VF devices - print message and bail.
 212	 */
 213	e_err(probe, "Unable to allocate memory for VF Data Storage - "
 214	      "SRIOV disabled\n");
 215	ixgbe_disable_sriov(adapter);
 216}
 217
 218#endif /* #ifdef CONFIG_PCI_IOV */
 219int ixgbe_disable_sriov(struct ixgbe_adapter *adapter)
 220{
 221	unsigned int num_vfs = adapter->num_vfs, vf;
 222	struct ixgbe_hw *hw = &adapter->hw;
 223	u32 gpie;
 224	u32 vmdctl;
 225	int rss;
 226
 227	/* set num VFs to 0 to prevent access to vfinfo */
 228	adapter->num_vfs = 0;
 229
 230	/* put the reference to all of the vf devices */
 231	for (vf = 0; vf < num_vfs; ++vf) {
 232		struct pci_dev *vfdev = adapter->vfinfo[vf].vfdev;
 233
 234		if (!vfdev)
 235			continue;
 236		adapter->vfinfo[vf].vfdev = NULL;
 237		pci_dev_put(vfdev);
 238	}
 239
 240	/* free VF control structures */
 241	kfree(adapter->vfinfo);
 242	adapter->vfinfo = NULL;
 243
 244	/* free macvlan list */
 245	kfree(adapter->mv_list);
 246	adapter->mv_list = NULL;
 247
 248	/* if SR-IOV is already disabled then there is nothing to do */
 249	if (!(adapter->flags & IXGBE_FLAG_SRIOV_ENABLED))
 250		return 0;
 251
 252#ifdef CONFIG_PCI_IOV
 253	/*
 254	 * If our VFs are assigned we cannot shut down SR-IOV
 255	 * without causing issues, so just leave the hardware
 256	 * available but disabled
 257	 */
 258	if (pci_vfs_assigned(adapter->pdev)) {
 259		e_dev_warn("Unloading driver while VFs are assigned - VFs will not be deallocated\n");
 260		return -EPERM;
 261	}
 262	/* disable iov and allow time for transactions to clear */
 263	pci_disable_sriov(adapter->pdev);
 264#endif
 265
 266	/* turn off device IOV mode */
 267	IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, 0);
 268	gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
 269	gpie &= ~IXGBE_GPIE_VTMODE_MASK;
 270	IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
 271
 272	/* set default pool back to 0 */
 273	vmdctl = IXGBE_READ_REG(hw, IXGBE_VT_CTL);
 274	vmdctl &= ~IXGBE_VT_CTL_POOL_MASK;
 275	IXGBE_WRITE_REG(hw, IXGBE_VT_CTL, vmdctl);
 276	IXGBE_WRITE_FLUSH(hw);
 277
 278	/* Disable VMDq flag so device will be set in VM mode */
 279	if (adapter->ring_feature[RING_F_VMDQ].limit == 1) {
 280		adapter->flags &= ~IXGBE_FLAG_VMDQ_ENABLED;
 281		adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED;
 282		rss = min_t(int, ixgbe_max_rss_indices(adapter),
 283			    num_online_cpus());
 284	} else {
 285		rss = min_t(int, IXGBE_MAX_L2A_QUEUES, num_online_cpus());
 286	}
 287
 288	adapter->ring_feature[RING_F_VMDQ].offset = 0;
 289	adapter->ring_feature[RING_F_RSS].limit = rss;
 290
 291	/* take a breather then clean up driver data */
 292	msleep(100);
 293	return 0;
 294}
 295
 296static int ixgbe_pci_sriov_enable(struct pci_dev *dev, int num_vfs)
 297{
 298#ifdef CONFIG_PCI_IOV
 299	struct ixgbe_adapter *adapter = pci_get_drvdata(dev);
 300	int err = 0;
 301	int i;
 302	int pre_existing_vfs = pci_num_vf(dev);
 303
 304	if (pre_existing_vfs && pre_existing_vfs != num_vfs)
 305		err = ixgbe_disable_sriov(adapter);
 306	else if (pre_existing_vfs && pre_existing_vfs == num_vfs)
 307		return num_vfs;
 308
 309	if (err)
 310		return err;
 311
 312	/* While the SR-IOV capability structure reports total VFs to be 64,
 313	 * we have to limit the actual number allocated based on two factors.
 314	 * First, we reserve some transmit/receive resources for the PF.
 315	 * Second, VMDQ also uses the same pools that SR-IOV does. We need to
 316	 * account for this, so that we don't accidentally allocate more VFs
 317	 * than we have available pools. The PCI bus driver already checks for
 318	 * other values out of range.
 319	 */
 320	if ((num_vfs + adapter->num_rx_pools) > IXGBE_MAX_VF_FUNCTIONS)
 321		return -EPERM;
 322
 323	adapter->num_vfs = num_vfs;
 324
 325	err = __ixgbe_enable_sriov(adapter);
 326	if (err)
 327		return  err;
 328
 329	for (i = 0; i < adapter->num_vfs; i++)
 330		ixgbe_vf_configuration(dev, (i | 0x10000000));
 331
 332	err = pci_enable_sriov(dev, num_vfs);
 333	if (err) {
 334		e_dev_warn("Failed to enable PCI sriov: %d\n", err);
 335		return err;
 336	}
 337	ixgbe_get_vfs(adapter);
 338	ixgbe_sriov_reinit(adapter);
 339
 340	return num_vfs;
 341#else
 342	return 0;
 343#endif
 344}
 345
 346static int ixgbe_pci_sriov_disable(struct pci_dev *dev)
 347{
 348	struct ixgbe_adapter *adapter = pci_get_drvdata(dev);
 349	int err;
 350#ifdef CONFIG_PCI_IOV
 351	u32 current_flags = adapter->flags;
 352#endif
 353
 354	err = ixgbe_disable_sriov(adapter);
 355
 356	/* Only reinit if no error and state changed */
 357#ifdef CONFIG_PCI_IOV
 358	if (!err && current_flags != adapter->flags)
 359		ixgbe_sriov_reinit(adapter);
 360#endif
 361
 362	return err;
 363}
 364
 365int ixgbe_pci_sriov_configure(struct pci_dev *dev, int num_vfs)
 366{
 367	if (num_vfs == 0)
 368		return ixgbe_pci_sriov_disable(dev);
 369	else
 370		return ixgbe_pci_sriov_enable(dev, num_vfs);
 371}
 372
 373static int ixgbe_set_vf_multicasts(struct ixgbe_adapter *adapter,
 374				   u32 *msgbuf, u32 vf)
 375{
 376	int entries = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK)
 377		       >> IXGBE_VT_MSGINFO_SHIFT;
 378	u16 *hash_list = (u16 *)&msgbuf[1];
 379	struct vf_data_storage *vfinfo = &adapter->vfinfo[vf];
 380	struct ixgbe_hw *hw = &adapter->hw;
 381	int i;
 382	u32 vector_bit;
 383	u32 vector_reg;
 384	u32 mta_reg;
 385	u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf));
 386
 387	/* only so many hash values supported */
 388	entries = min(entries, IXGBE_MAX_VF_MC_ENTRIES);
 389
 390	/*
 391	 * salt away the number of multi cast addresses assigned
 392	 * to this VF for later use to restore when the PF multi cast
 393	 * list changes
 394	 */
 395	vfinfo->num_vf_mc_hashes = entries;
 396
 397	/*
 398	 * VFs are limited to using the MTA hash table for their multicast
 399	 * addresses
 400	 */
 401	for (i = 0; i < entries; i++) {
 402		vfinfo->vf_mc_hashes[i] = hash_list[i];
 403	}
 404
 405	for (i = 0; i < vfinfo->num_vf_mc_hashes; i++) {
 406		vector_reg = (vfinfo->vf_mc_hashes[i] >> 5) & 0x7F;
 407		vector_bit = vfinfo->vf_mc_hashes[i] & 0x1F;
 408		mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg));
 409		mta_reg |= (1 << vector_bit);
 410		IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg);
 411	}
 412	vmolr |= IXGBE_VMOLR_ROMPE;
 413	IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr);
 414
 415	return 0;
 416}
 417
 418#ifdef CONFIG_PCI_IOV
 419void ixgbe_restore_vf_multicasts(struct ixgbe_adapter *adapter)
 420{
 421	struct ixgbe_hw *hw = &adapter->hw;
 422	struct vf_data_storage *vfinfo;
 423	int i, j;
 424	u32 vector_bit;
 425	u32 vector_reg;
 426	u32 mta_reg;
 427
 428	for (i = 0; i < adapter->num_vfs; i++) {
 429		u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(i));
 430		vfinfo = &adapter->vfinfo[i];
 431		for (j = 0; j < vfinfo->num_vf_mc_hashes; j++) {
 432			hw->addr_ctrl.mta_in_use++;
 433			vector_reg = (vfinfo->vf_mc_hashes[j] >> 5) & 0x7F;
 434			vector_bit = vfinfo->vf_mc_hashes[j] & 0x1F;
 435			mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg));
 436			mta_reg |= (1 << vector_bit);
 437			IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg);
 438		}
 439
 440		if (vfinfo->num_vf_mc_hashes)
 441			vmolr |= IXGBE_VMOLR_ROMPE;
 442		else
 443			vmolr &= ~IXGBE_VMOLR_ROMPE;
 444		IXGBE_WRITE_REG(hw, IXGBE_VMOLR(i), vmolr);
 445	}
 446
 447	/* Restore any VF macvlans */
 448	ixgbe_full_sync_mac_table(adapter);
 449}
 450#endif
 451
 452static int ixgbe_set_vf_vlan(struct ixgbe_adapter *adapter, int add, int vid,
 453			     u32 vf)
 454{
 455	struct ixgbe_hw *hw = &adapter->hw;
 456	int err;
 457
 458	/* If VLAN overlaps with one the PF is currently monitoring make
 459	 * sure that we are able to allocate a VLVF entry.  This may be
 460	 * redundant but it guarantees PF will maintain visibility to
 461	 * the VLAN.
 462	 */
 463	if (add && test_bit(vid, adapter->active_vlans)) {
 464		err = hw->mac.ops.set_vfta(hw, vid, VMDQ_P(0), true, false);
 465		if (err)
 466			return err;
 467	}
 468
 469	err = hw->mac.ops.set_vfta(hw, vid, vf, !!add, false);
 470
 471	if (add && !err)
 472		return err;
 473
 474	/* If we failed to add the VF VLAN or we are removing the VF VLAN
 475	 * we may need to drop the PF pool bit in order to allow us to free
 476	 * up the VLVF resources.
 477	 */
 478	if (test_bit(vid, adapter->active_vlans) ||
 479	    (adapter->flags2 & IXGBE_FLAG2_VLAN_PROMISC))
 480		ixgbe_update_pf_promisc_vlvf(adapter, vid);
 481
 482	return err;
 483}
 484
 485static s32 ixgbe_set_vf_lpe(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
 486{
 487	struct ixgbe_hw *hw = &adapter->hw;
 488	int max_frame = msgbuf[1];
 489	u32 max_frs;
 490
 491	/*
 492	 * For 82599EB we have to keep all PFs and VFs operating with
 493	 * the same max_frame value in order to avoid sending an oversize
 494	 * frame to a VF.  In order to guarantee this is handled correctly
 495	 * for all cases we have several special exceptions to take into
 496	 * account before we can enable the VF for receive
 497	 */
 498	if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
 499		struct net_device *dev = adapter->netdev;
 500		int pf_max_frame = dev->mtu + ETH_HLEN;
 501		u32 reg_offset, vf_shift, vfre;
 502		s32 err = 0;
 503
 504#ifdef CONFIG_FCOE
 505		if (dev->features & NETIF_F_FCOE_MTU)
 506			pf_max_frame = max_t(int, pf_max_frame,
 507					     IXGBE_FCOE_JUMBO_FRAME_SIZE);
 508
 509#endif /* CONFIG_FCOE */
 510		switch (adapter->vfinfo[vf].vf_api) {
 511		case ixgbe_mbox_api_11:
 512		case ixgbe_mbox_api_12:
 513			/*
 514			 * Version 1.1 supports jumbo frames on VFs if PF has
 515			 * jumbo frames enabled which means legacy VFs are
 516			 * disabled
 517			 */
 518			if (pf_max_frame > ETH_FRAME_LEN)
 519				break;
 520		default:
 521			/*
 522			 * If the PF or VF are running w/ jumbo frames enabled
 523			 * we need to shut down the VF Rx path as we cannot
 524			 * support jumbo frames on legacy VFs
 525			 */
 526			if ((pf_max_frame > ETH_FRAME_LEN) ||
 527			    (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)))
 528				err = -EINVAL;
 529			break;
 530		}
 531
 532		/* determine VF receive enable location */
 533		vf_shift = vf % 32;
 534		reg_offset = vf / 32;
 535
 536		/* enable or disable receive depending on error */
 537		vfre = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset));
 538		if (err)
 539			vfre &= ~(1 << vf_shift);
 540		else
 541			vfre |= 1 << vf_shift;
 542		IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), vfre);
 543
 544		if (err) {
 545			e_err(drv, "VF max_frame %d out of range\n", max_frame);
 546			return err;
 547		}
 548	}
 549
 550	/* MTU < 68 is an error and causes problems on some kernels */
 551	if (max_frame > IXGBE_MAX_JUMBO_FRAME_SIZE) {
 552		e_err(drv, "VF max_frame %d out of range\n", max_frame);
 553		return -EINVAL;
 554	}
 555
 556	/* pull current max frame size from hardware */
 557	max_frs = IXGBE_READ_REG(hw, IXGBE_MAXFRS);
 558	max_frs &= IXGBE_MHADD_MFS_MASK;
 559	max_frs >>= IXGBE_MHADD_MFS_SHIFT;
 560
 561	if (max_frs < max_frame) {
 562		max_frs = max_frame << IXGBE_MHADD_MFS_SHIFT;
 563		IXGBE_WRITE_REG(hw, IXGBE_MAXFRS, max_frs);
 564	}
 565
 566	e_info(hw, "VF requests change max MTU to %d\n", max_frame);
 567
 568	return 0;
 569}
 570
 571static void ixgbe_set_vmolr(struct ixgbe_hw *hw, u32 vf, bool aupe)
 572{
 573	u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf));
 574	vmolr |= IXGBE_VMOLR_BAM;
 575	if (aupe)
 576		vmolr |= IXGBE_VMOLR_AUPE;
 577	else
 578		vmolr &= ~IXGBE_VMOLR_AUPE;
 579	IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr);
 580}
 581
 582static void ixgbe_clear_vmvir(struct ixgbe_adapter *adapter, u32 vf)
 583{
 584	struct ixgbe_hw *hw = &adapter->hw;
 585
 586	IXGBE_WRITE_REG(hw, IXGBE_VMVIR(vf), 0);
 587}
 588
 589static void ixgbe_clear_vf_vlans(struct ixgbe_adapter *adapter, u32 vf)
 590{
 591	struct ixgbe_hw *hw = &adapter->hw;
 592	u32 i;
 593
 594	/* post increment loop, covers VLVF_ENTRIES - 1 to 0 */
 595	for (i = IXGBE_VLVF_ENTRIES; i--;) {
 596		u32 bits[2], vlvfb, vid, vfta, vlvf;
 597		u32 word = i * 2 + vf / 32;
 598		u32 mask = 1 << (vf % 32);
 599
 600		vlvfb = IXGBE_READ_REG(hw, IXGBE_VLVFB(word));
 601
 602		/* if our bit isn't set we can skip it */
 603		if (!(vlvfb & mask))
 604			continue;
 605
 606		/* clear our bit from vlvfb */
 607		vlvfb ^= mask;
 608
 609		/* create 64b mask to chedk to see if we should clear VLVF */
 610		bits[word % 2] = vlvfb;
 611		bits[~word % 2] = IXGBE_READ_REG(hw, IXGBE_VLVFB(word ^ 1));
 612
 613		/* if promisc is enabled, PF will be present, leave VFTA */
 614		if (adapter->flags2 & IXGBE_FLAG2_VLAN_PROMISC) {
 615			bits[VMDQ_P(0) / 32] &= ~(1 << (VMDQ_P(0) % 32));
 616
 617			if (bits[0] || bits[1])
 618				goto update_vlvfb;
 619			goto update_vlvf;
 620		}
 621
 622		/* if other pools are present, just remove ourselves */
 623		if (bits[0] || bits[1])
 624			goto update_vlvfb;
 625
 626		/* if we cannot determine VLAN just remove ourselves */
 627		vlvf = IXGBE_READ_REG(hw, IXGBE_VLVF(i));
 628		if (!vlvf)
 629			goto update_vlvfb;
 630
 631		vid = vlvf & VLAN_VID_MASK;
 632		mask = 1 << (vid % 32);
 633
 634		/* clear bit from VFTA */
 635		vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(vid / 32));
 636		if (vfta & mask)
 637			IXGBE_WRITE_REG(hw, IXGBE_VFTA(vid / 32), vfta ^ mask);
 638update_vlvf:
 639		/* clear POOL selection enable */
 640		IXGBE_WRITE_REG(hw, IXGBE_VLVF(i), 0);
 641update_vlvfb:
 642		/* clear pool bits */
 643		IXGBE_WRITE_REG(hw, IXGBE_VLVFB(word), vlvfb);
 644	}
 645}
 646
 647static inline void ixgbe_vf_reset_event(struct ixgbe_adapter *adapter, u32 vf)
 648{
 649	struct ixgbe_hw *hw = &adapter->hw;
 650	struct vf_data_storage *vfinfo = &adapter->vfinfo[vf];
 651	u8 num_tcs = netdev_get_num_tc(adapter->netdev);
 652
 653	/* remove VLAN filters beloning to this VF */
 654	ixgbe_clear_vf_vlans(adapter, vf);
 655
 656	/* add back PF assigned VLAN or VLAN 0 */
 657	ixgbe_set_vf_vlan(adapter, true, vfinfo->pf_vlan, vf);
 658
 659	/* reset offloads to defaults */
 660	ixgbe_set_vmolr(hw, vf, !vfinfo->pf_vlan);
 661
 662	/* set outgoing tags for VFs */
 663	if (!vfinfo->pf_vlan && !vfinfo->pf_qos && !num_tcs) {
 664		ixgbe_clear_vmvir(adapter, vf);
 665	} else {
 666		if (vfinfo->pf_qos || !num_tcs)
 667			ixgbe_set_vmvir(adapter, vfinfo->pf_vlan,
 668					vfinfo->pf_qos, vf);
 669		else
 670			ixgbe_set_vmvir(adapter, vfinfo->pf_vlan,
 671					adapter->default_up, vf);
 672
 673		if (vfinfo->spoofchk_enabled)
 674			hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf);
 675	}
 676
 677	/* reset multicast table array for vf */
 678	adapter->vfinfo[vf].num_vf_mc_hashes = 0;
 679
 680	/* Flush and reset the mta with the new values */
 681	ixgbe_set_rx_mode(adapter->netdev);
 682
 683	ixgbe_del_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf);
 684
 685	/* reset VF api back to unknown */
 686	adapter->vfinfo[vf].vf_api = ixgbe_mbox_api_10;
 687}
 688
 689static int ixgbe_set_vf_mac(struct ixgbe_adapter *adapter,
 690			    int vf, unsigned char *mac_addr)
 691{
 692	ixgbe_del_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf);
 693	memcpy(adapter->vfinfo[vf].vf_mac_addresses, mac_addr, ETH_ALEN);
 694	ixgbe_add_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf);
 695
 696	return 0;
 697}
 698
 699static int ixgbe_set_vf_macvlan(struct ixgbe_adapter *adapter,
 700				int vf, int index, unsigned char *mac_addr)
 701{
 702	struct list_head *pos;
 703	struct vf_macvlans *entry;
 704
 705	if (index <= 1) {
 706		list_for_each(pos, &adapter->vf_mvs.l) {
 707			entry = list_entry(pos, struct vf_macvlans, l);
 708			if (entry->vf == vf) {
 709				entry->vf = -1;
 710				entry->free = true;
 711				entry->is_macvlan = false;
 712				ixgbe_del_mac_filter(adapter,
 713						     entry->vf_macvlan, vf);
 714			}
 715		}
 716	}
 717
 718	/*
 719	 * If index was zero then we were asked to clear the uc list
 720	 * for the VF.  We're done.
 721	 */
 722	if (!index)
 723		return 0;
 724
 725	entry = NULL;
 726
 727	list_for_each(pos, &adapter->vf_mvs.l) {
 728		entry = list_entry(pos, struct vf_macvlans, l);
 729		if (entry->free)
 730			break;
 731	}
 732
 733	/*
 734	 * If we traversed the entire list and didn't find a free entry
 735	 * then we're out of space on the RAR table.  Also entry may
 736	 * be NULL because the original memory allocation for the list
 737	 * failed, which is not fatal but does mean we can't support
 738	 * VF requests for MACVLAN because we couldn't allocate
 739	 * memory for the list management required.
 740	 */
 741	if (!entry || !entry->free)
 742		return -ENOSPC;
 743
 744	entry->free = false;
 745	entry->is_macvlan = true;
 746	entry->vf = vf;
 747	memcpy(entry->vf_macvlan, mac_addr, ETH_ALEN);
 748
 749	ixgbe_add_mac_filter(adapter, mac_addr, vf);
 750
 751	return 0;
 752}
 753
 754int ixgbe_vf_configuration(struct pci_dev *pdev, unsigned int event_mask)
 755{
 756	struct ixgbe_adapter *adapter = pci_get_drvdata(pdev);
 757	unsigned int vfn = (event_mask & 0x3f);
 758
 759	bool enable = ((event_mask & 0x10000000U) != 0);
 760
 761	if (enable)
 762		eth_zero_addr(adapter->vfinfo[vfn].vf_mac_addresses);
 763
 764	return 0;
 765}
 766
 767static inline void ixgbe_write_qde(struct ixgbe_adapter *adapter, u32 vf,
 768				   u32 qde)
 769{
 770	struct ixgbe_hw *hw = &adapter->hw;
 771	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
 772	u32 q_per_pool = __ALIGN_MASK(1, ~vmdq->mask);
 773	int i;
 774
 775	for (i = vf * q_per_pool; i < ((vf + 1) * q_per_pool); i++) {
 776		u32 reg;
 777
 778		/* flush previous write */
 779		IXGBE_WRITE_FLUSH(hw);
 780
 781		/* indicate to hardware that we want to set drop enable */
 782		reg = IXGBE_QDE_WRITE | IXGBE_QDE_ENABLE;
 783		reg |= i <<  IXGBE_QDE_IDX_SHIFT;
 784		IXGBE_WRITE_REG(hw, IXGBE_QDE, reg);
 785	}
 786}
 787
 788static int ixgbe_vf_reset_msg(struct ixgbe_adapter *adapter, u32 vf)
 789{
 790	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
 791	struct ixgbe_hw *hw = &adapter->hw;
 792	unsigned char *vf_mac = adapter->vfinfo[vf].vf_mac_addresses;
 793	u32 reg, reg_offset, vf_shift;
 794	u32 msgbuf[4] = {0, 0, 0, 0};
 795	u8 *addr = (u8 *)(&msgbuf[1]);
 796	u32 q_per_pool = __ALIGN_MASK(1, ~vmdq->mask);
 797	int i;
 798
 799	e_info(probe, "VF Reset msg received from vf %d\n", vf);
 800
 801	/* reset the filters for the device */
 802	ixgbe_vf_reset_event(adapter, vf);
 803
 804	/* set vf mac address */
 805	if (!is_zero_ether_addr(vf_mac))
 806		ixgbe_set_vf_mac(adapter, vf, vf_mac);
 807
 808	vf_shift = vf % 32;
 809	reg_offset = vf / 32;
 810
 811	/* enable transmit for vf */
 812	reg = IXGBE_READ_REG(hw, IXGBE_VFTE(reg_offset));
 813	reg |= 1 << vf_shift;
 814	IXGBE_WRITE_REG(hw, IXGBE_VFTE(reg_offset), reg);
 815
 816	/* force drop enable for all VF Rx queues */
 817	ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE);
 818
 819	/* enable receive for vf */
 820	reg = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset));
 821	reg |= 1 << vf_shift;
 822	/*
 823	 * The 82599 cannot support a mix of jumbo and non-jumbo PF/VFs.
 824	 * For more info take a look at ixgbe_set_vf_lpe
 825	 */
 826	if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
 827		struct net_device *dev = adapter->netdev;
 828		int pf_max_frame = dev->mtu + ETH_HLEN;
 829
 830#ifdef CONFIG_FCOE
 831		if (dev->features & NETIF_F_FCOE_MTU)
 832			pf_max_frame = max_t(int, pf_max_frame,
 833					     IXGBE_FCOE_JUMBO_FRAME_SIZE);
 834
 835#endif /* CONFIG_FCOE */
 836		if (pf_max_frame > ETH_FRAME_LEN)
 837			reg &= ~(1 << vf_shift);
 838	}
 839	IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), reg);
 840
 841	/* enable VF mailbox for further messages */
 842	adapter->vfinfo[vf].clear_to_send = true;
 843
 844	/* Enable counting of spoofed packets in the SSVPC register */
 845	reg = IXGBE_READ_REG(hw, IXGBE_VMECM(reg_offset));
 846	reg |= (1 << vf_shift);
 847	IXGBE_WRITE_REG(hw, IXGBE_VMECM(reg_offset), reg);
 848
 849	/*
 850	 * Reset the VFs TDWBAL and TDWBAH registers
 851	 * which are not cleared by an FLR
 852	 */
 853	for (i = 0; i < q_per_pool; i++) {
 854		IXGBE_WRITE_REG(hw, IXGBE_PVFTDWBAHn(q_per_pool, vf, i), 0);
 855		IXGBE_WRITE_REG(hw, IXGBE_PVFTDWBALn(q_per_pool, vf, i), 0);
 856	}
 857
 858	/* reply to reset with ack and vf mac address */
 859	msgbuf[0] = IXGBE_VF_RESET;
 860	if (!is_zero_ether_addr(vf_mac)) {
 861		msgbuf[0] |= IXGBE_VT_MSGTYPE_ACK;
 862		memcpy(addr, vf_mac, ETH_ALEN);
 863	} else {
 864		msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK;
 865		dev_warn(&adapter->pdev->dev,
 866			 "VF %d has no MAC address assigned, you may have to assign one manually\n",
 867			 vf);
 868	}
 869
 870	/*
 871	 * Piggyback the multicast filter type so VF can compute the
 872	 * correct vectors
 873	 */
 874	msgbuf[3] = hw->mac.mc_filter_type;
 875	ixgbe_write_mbx(hw, msgbuf, IXGBE_VF_PERMADDR_MSG_LEN, vf);
 876
 877	return 0;
 878}
 879
 880static int ixgbe_set_vf_mac_addr(struct ixgbe_adapter *adapter,
 881				 u32 *msgbuf, u32 vf)
 882{
 883	u8 *new_mac = ((u8 *)(&msgbuf[1]));
 884
 885	if (!is_valid_ether_addr(new_mac)) {
 886		e_warn(drv, "VF %d attempted to set invalid mac\n", vf);
 887		return -1;
 888	}
 889
 890	if (adapter->vfinfo[vf].pf_set_mac &&
 891	    !ether_addr_equal(adapter->vfinfo[vf].vf_mac_addresses, new_mac)) {
 892		e_warn(drv,
 893		       "VF %d attempted to override administratively set MAC address\n"
 894		       "Reload the VF driver to resume operations\n",
 895		       vf);
 896		return -1;
 897	}
 898
 899	return ixgbe_set_vf_mac(adapter, vf, new_mac) < 0;
 900}
 901
 902static int ixgbe_set_vf_vlan_msg(struct ixgbe_adapter *adapter,
 903				 u32 *msgbuf, u32 vf)
 904{
 905	u32 add = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >> IXGBE_VT_MSGINFO_SHIFT;
 906	u32 vid = (msgbuf[1] & IXGBE_VLVF_VLANID_MASK);
 907	u8 tcs = netdev_get_num_tc(adapter->netdev);
 908	struct ixgbe_hw *hw = &adapter->hw;
 909	int err;
 910
 911	if (adapter->vfinfo[vf].pf_vlan || tcs) {
 912		e_warn(drv,
 913		       "VF %d attempted to override administratively set VLAN configuration\n"
 914		       "Reload the VF driver to resume operations\n",
 915		       vf);
 916		return -1;
 917	}
 918
 919	/* VLAN 0 is a special case, don't allow it to be removed */
 920	if (!vid && !add)
 921		return 0;
 922
 923	err = ixgbe_set_vf_vlan(adapter, add, vid, vf);
 924	if (err)
 925		return err;
 926
 927	if (adapter->vfinfo[vf].spoofchk_enabled)
 928		hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf);
 929
 930	if (add)
 931		adapter->vfinfo[vf].vlan_count++;
 932	else if (adapter->vfinfo[vf].vlan_count)
 933		adapter->vfinfo[vf].vlan_count--;
 934
 935	return 0;
 936}
 937
 938static int ixgbe_set_vf_macvlan_msg(struct ixgbe_adapter *adapter,
 939				    u32 *msgbuf, u32 vf)
 940{
 941	u8 *new_mac = ((u8 *)(&msgbuf[1]));
 942	int index = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >>
 943		    IXGBE_VT_MSGINFO_SHIFT;
 944	int err;
 945
 946	if (adapter->vfinfo[vf].pf_set_mac && index > 0) {
 947		e_warn(drv,
 948		       "VF %d requested MACVLAN filter but is administratively denied\n",
 949		       vf);
 950		return -1;
 951	}
 952
 953	/* An non-zero index indicates the VF is setting a filter */
 954	if (index) {
 955		if (!is_valid_ether_addr(new_mac)) {
 956			e_warn(drv, "VF %d attempted to set invalid mac\n", vf);
 957			return -1;
 958		}
 959
 960		/*
 961		 * If the VF is allowed to set MAC filters then turn off
 962		 * anti-spoofing to avoid false positives.
 963		 */
 964		if (adapter->vfinfo[vf].spoofchk_enabled)
 965			ixgbe_ndo_set_vf_spoofchk(adapter->netdev, vf, false);
 966	}
 967
 968	err = ixgbe_set_vf_macvlan(adapter, vf, index, new_mac);
 969	if (err == -ENOSPC)
 970		e_warn(drv,
 971		       "VF %d has requested a MACVLAN filter but there is no space for it\n",
 972		       vf);
 973
 974	return err < 0;
 975}
 976
 977static int ixgbe_negotiate_vf_api(struct ixgbe_adapter *adapter,
 978				  u32 *msgbuf, u32 vf)
 979{
 980	int api = msgbuf[1];
 981
 982	switch (api) {
 983	case ixgbe_mbox_api_10:
 984	case ixgbe_mbox_api_11:
 985	case ixgbe_mbox_api_12:
 986		adapter->vfinfo[vf].vf_api = api;
 987		return 0;
 988	default:
 989		break;
 990	}
 991
 992	e_info(drv, "VF %d requested invalid api version %u\n", vf, api);
 993
 994	return -1;
 995}
 996
 997static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter,
 998			       u32 *msgbuf, u32 vf)
 999{
1000	struct net_device *dev = adapter->netdev;
1001	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
1002	unsigned int default_tc = 0;
1003	u8 num_tcs = netdev_get_num_tc(dev);
1004
1005	/* verify the PF is supporting the correct APIs */
1006	switch (adapter->vfinfo[vf].vf_api) {
1007	case ixgbe_mbox_api_20:
1008	case ixgbe_mbox_api_11:
1009	case ixgbe_mbox_api_12:
1010		break;
1011	default:
1012		return -1;
1013	}
1014
1015	/* only allow 1 Tx queue for bandwidth limiting */
1016	msgbuf[IXGBE_VF_TX_QUEUES] = __ALIGN_MASK(1, ~vmdq->mask);
1017	msgbuf[IXGBE_VF_RX_QUEUES] = __ALIGN_MASK(1, ~vmdq->mask);
1018
1019	/* if TCs > 1 determine which TC belongs to default user priority */
1020	if (num_tcs > 1)
1021		default_tc = netdev_get_prio_tc_map(dev, adapter->default_up);
1022
1023	/* notify VF of need for VLAN tag stripping, and correct queue */
1024	if (num_tcs)
1025		msgbuf[IXGBE_VF_TRANS_VLAN] = num_tcs;
1026	else if (adapter->vfinfo[vf].pf_vlan || adapter->vfinfo[vf].pf_qos)
1027		msgbuf[IXGBE_VF_TRANS_VLAN] = 1;
1028	else
1029		msgbuf[IXGBE_VF_TRANS_VLAN] = 0;
1030
1031	/* notify VF of default queue */
1032	msgbuf[IXGBE_VF_DEF_QUEUE] = default_tc;
1033
1034	return 0;
1035}
1036
1037static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
1038{
1039	u32 i, j;
1040	u32 *out_buf = &msgbuf[1];
1041	const u8 *reta = adapter->rss_indir_tbl;
1042	u32 reta_size = ixgbe_rss_indir_tbl_entries(adapter);
1043
1044	/* Check if operation is permitted */
1045	if (!adapter->vfinfo[vf].rss_query_enabled)
1046		return -EPERM;
1047
1048	/* verify the PF is supporting the correct API */
1049	if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
1050		return -EOPNOTSUPP;
1051
1052	/* This mailbox command is supported (required) only for 82599 and x540
1053	 * VFs which support up to 4 RSS queues. Therefore we will compress the
1054	 * RETA by saving only 2 bits from each entry. This way we will be able
1055	 * to transfer the whole RETA in a single mailbox operation.
1056	 */
1057	for (i = 0; i < reta_size / 16; i++) {
1058		out_buf[i] = 0;
1059		for (j = 0; j < 16; j++)
1060			out_buf[i] |= (u32)(reta[16 * i + j] & 0x3) << (2 * j);
1061	}
1062
1063	return 0;
1064}
1065
1066static int ixgbe_get_vf_rss_key(struct ixgbe_adapter *adapter,
1067				u32 *msgbuf, u32 vf)
1068{
1069	u32 *rss_key = &msgbuf[1];
1070
1071	/* Check if the operation is permitted */
1072	if (!adapter->vfinfo[vf].rss_query_enabled)
1073		return -EPERM;
1074
1075	/* verify the PF is supporting the correct API */
1076	if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
1077		return -EOPNOTSUPP;
1078
1079	memcpy(rss_key, adapter->rss_key, sizeof(adapter->rss_key));
1080
1081	return 0;
1082}
1083
1084static int ixgbe_update_vf_xcast_mode(struct ixgbe_adapter *adapter,
1085				      u32 *msgbuf, u32 vf)
1086{
1087	struct ixgbe_hw *hw = &adapter->hw;
1088	int xcast_mode = msgbuf[1];
1089	u32 vmolr, disable, enable;
1090
1091	/* verify the PF is supporting the correct APIs */
1092	switch (adapter->vfinfo[vf].vf_api) {
1093	case ixgbe_mbox_api_12:
1094		break;
1095	default:
1096		return -EOPNOTSUPP;
1097	}
1098
1099	if (xcast_mode > IXGBEVF_XCAST_MODE_MULTI &&
1100	    !adapter->vfinfo[vf].trusted) {
1101		xcast_mode = IXGBEVF_XCAST_MODE_MULTI;
1102	}
1103
1104	if (adapter->vfinfo[vf].xcast_mode == xcast_mode)
1105		goto out;
1106
1107	switch (xcast_mode) {
1108	case IXGBEVF_XCAST_MODE_NONE:
1109		disable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE | IXGBE_VMOLR_MPE;
1110		enable = 0;
1111		break;
1112	case IXGBEVF_XCAST_MODE_MULTI:
1113		disable = IXGBE_VMOLR_MPE;
1114		enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE;
1115		break;
1116	case IXGBEVF_XCAST_MODE_ALLMULTI:
1117		disable = 0;
1118		enable = IXGBE_VMOLR_BAM | IXGBE_VMOLR_ROMPE | IXGBE_VMOLR_MPE;
1119		break;
1120	default:
1121		return -EOPNOTSUPP;
1122	}
1123
1124	vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf));
1125	vmolr &= ~disable;
1126	vmolr |= enable;
1127	IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr);
1128
1129	adapter->vfinfo[vf].xcast_mode = xcast_mode;
1130
1131out:
1132	msgbuf[1] = xcast_mode;
1133
1134	return 0;
1135}
1136
1137static int ixgbe_rcv_msg_from_vf(struct ixgbe_adapter *adapter, u32 vf)
1138{
1139	u32 mbx_size = IXGBE_VFMAILBOX_SIZE;
1140	u32 msgbuf[IXGBE_VFMAILBOX_SIZE];
1141	struct ixgbe_hw *hw = &adapter->hw;
1142	s32 retval;
1143
1144	retval = ixgbe_read_mbx(hw, msgbuf, mbx_size, vf);
1145
1146	if (retval) {
1147		pr_err("Error receiving message from VF\n");
1148		return retval;
1149	}
1150
1151	/* this is a message we already processed, do nothing */
1152	if (msgbuf[0] & (IXGBE_VT_MSGTYPE_ACK | IXGBE_VT_MSGTYPE_NACK))
1153		return 0;
1154
1155	/* flush the ack before we write any messages back */
1156	IXGBE_WRITE_FLUSH(hw);
1157
1158	if (msgbuf[0] == IXGBE_VF_RESET)
1159		return ixgbe_vf_reset_msg(adapter, vf);
1160
1161	/*
1162	 * until the vf completes a virtual function reset it should not be
1163	 * allowed to start any configuration.
1164	 */
1165	if (!adapter->vfinfo[vf].clear_to_send) {
1166		msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK;
1167		ixgbe_write_mbx(hw, msgbuf, 1, vf);
1168		return 0;
1169	}
1170
1171	switch ((msgbuf[0] & 0xFFFF)) {
1172	case IXGBE_VF_SET_MAC_ADDR:
1173		retval = ixgbe_set_vf_mac_addr(adapter, msgbuf, vf);
1174		break;
1175	case IXGBE_VF_SET_MULTICAST:
1176		retval = ixgbe_set_vf_multicasts(adapter, msgbuf, vf);
1177		break;
1178	case IXGBE_VF_SET_VLAN:
1179		retval = ixgbe_set_vf_vlan_msg(adapter, msgbuf, vf);
1180		break;
1181	case IXGBE_VF_SET_LPE:
1182		retval = ixgbe_set_vf_lpe(adapter, msgbuf, vf);
1183		break;
1184	case IXGBE_VF_SET_MACVLAN:
1185		retval = ixgbe_set_vf_macvlan_msg(adapter, msgbuf, vf);
1186		break;
1187	case IXGBE_VF_API_NEGOTIATE:
1188		retval = ixgbe_negotiate_vf_api(adapter, msgbuf, vf);
1189		break;
1190	case IXGBE_VF_GET_QUEUES:
1191		retval = ixgbe_get_vf_queues(adapter, msgbuf, vf);
1192		break;
1193	case IXGBE_VF_GET_RETA:
1194		retval = ixgbe_get_vf_reta(adapter, msgbuf, vf);
1195		break;
1196	case IXGBE_VF_GET_RSS_KEY:
1197		retval = ixgbe_get_vf_rss_key(adapter, msgbuf, vf);
1198		break;
1199	case IXGBE_VF_UPDATE_XCAST_MODE:
1200		retval = ixgbe_update_vf_xcast_mode(adapter, msgbuf, vf);
1201		break;
1202	default:
1203		e_err(drv, "Unhandled Msg %8.8x\n", msgbuf[0]);
1204		retval = IXGBE_ERR_MBX;
1205		break;
1206	}
1207
1208	/* notify the VF of the results of what it sent us */
1209	if (retval)
1210		msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK;
1211	else
1212		msgbuf[0] |= IXGBE_VT_MSGTYPE_ACK;
1213
1214	msgbuf[0] |= IXGBE_VT_MSGTYPE_CTS;
1215
1216	ixgbe_write_mbx(hw, msgbuf, mbx_size, vf);
1217
1218	return retval;
1219}
1220
1221static void ixgbe_rcv_ack_from_vf(struct ixgbe_adapter *adapter, u32 vf)
1222{
1223	struct ixgbe_hw *hw = &adapter->hw;
1224	u32 msg = IXGBE_VT_MSGTYPE_NACK;
1225
1226	/* if device isn't clear to send it shouldn't be reading either */
1227	if (!adapter->vfinfo[vf].clear_to_send)
1228		ixgbe_write_mbx(hw, &msg, 1, vf);
1229}
1230
1231void ixgbe_msg_task(struct ixgbe_adapter *adapter)
1232{
1233	struct ixgbe_hw *hw = &adapter->hw;
1234	u32 vf;
1235
1236	for (vf = 0; vf < adapter->num_vfs; vf++) {
1237		/* process any reset requests */
1238		if (!ixgbe_check_for_rst(hw, vf))
1239			ixgbe_vf_reset_event(adapter, vf);
1240
1241		/* process any messages pending */
1242		if (!ixgbe_check_for_msg(hw, vf))
1243			ixgbe_rcv_msg_from_vf(adapter, vf);
1244
1245		/* process any acks */
1246		if (!ixgbe_check_for_ack(hw, vf))
1247			ixgbe_rcv_ack_from_vf(adapter, vf);
1248	}
1249}
1250
1251void ixgbe_disable_tx_rx(struct ixgbe_adapter *adapter)
1252{
1253	struct ixgbe_hw *hw = &adapter->hw;
1254
1255	/* disable transmit and receive for all vfs */
1256	IXGBE_WRITE_REG(hw, IXGBE_VFTE(0), 0);
1257	IXGBE_WRITE_REG(hw, IXGBE_VFTE(1), 0);
1258
1259	IXGBE_WRITE_REG(hw, IXGBE_VFRE(0), 0);
1260	IXGBE_WRITE_REG(hw, IXGBE_VFRE(1), 0);
1261}
1262
1263static inline void ixgbe_ping_vf(struct ixgbe_adapter *adapter, int vf)
1264{
1265	struct ixgbe_hw *hw = &adapter->hw;
1266	u32 ping;
1267
1268	ping = IXGBE_PF_CONTROL_MSG;
1269	if (adapter->vfinfo[vf].clear_to_send)
1270		ping |= IXGBE_VT_MSGTYPE_CTS;
1271	ixgbe_write_mbx(hw, &ping, 1, vf);
1272}
1273
1274void ixgbe_ping_all_vfs(struct ixgbe_adapter *adapter)
1275{
1276	struct ixgbe_hw *hw = &adapter->hw;
1277	u32 ping;
1278	int i;
1279
1280	for (i = 0 ; i < adapter->num_vfs; i++) {
1281		ping = IXGBE_PF_CONTROL_MSG;
1282		if (adapter->vfinfo[i].clear_to_send)
1283			ping |= IXGBE_VT_MSGTYPE_CTS;
1284		ixgbe_write_mbx(hw, &ping, 1, i);
1285	}
1286}
1287
1288int ixgbe_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac)
1289{
1290	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1291	if (!is_valid_ether_addr(mac) || (vf >= adapter->num_vfs))
1292		return -EINVAL;
1293	adapter->vfinfo[vf].pf_set_mac = true;
1294	dev_info(&adapter->pdev->dev, "setting MAC %pM on VF %d\n", mac, vf);
1295	dev_info(&adapter->pdev->dev, "Reload the VF driver to make this"
1296				      " change effective.");
1297	if (test_bit(__IXGBE_DOWN, &adapter->state)) {
1298		dev_warn(&adapter->pdev->dev, "The VF MAC address has been set,"
1299			 " but the PF device is not up.\n");
1300		dev_warn(&adapter->pdev->dev, "Bring the PF device up before"
1301			 " attempting to use the VF device.\n");
1302	}
1303	return ixgbe_set_vf_mac(adapter, vf, mac);
1304}
1305
1306static int ixgbe_enable_port_vlan(struct ixgbe_adapter *adapter, int vf,
1307				  u16 vlan, u8 qos)
1308{
1309	struct ixgbe_hw *hw = &adapter->hw;
1310	int err;
1311
1312	err = ixgbe_set_vf_vlan(adapter, true, vlan, vf);
1313	if (err)
1314		goto out;
1315
1316	/* Revoke tagless access via VLAN 0 */
1317	ixgbe_set_vf_vlan(adapter, false, 0, vf);
1318
1319	ixgbe_set_vmvir(adapter, vlan, qos, vf);
1320	ixgbe_set_vmolr(hw, vf, false);
1321	if (adapter->vfinfo[vf].spoofchk_enabled)
1322		hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf);
1323	adapter->vfinfo[vf].vlan_count++;
1324
1325	/* enable hide vlan on X550 */
1326	if (hw->mac.type >= ixgbe_mac_X550)
1327		ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE |
1328				IXGBE_QDE_HIDE_VLAN);
1329
1330	adapter->vfinfo[vf].pf_vlan = vlan;
1331	adapter->vfinfo[vf].pf_qos = qos;
1332	dev_info(&adapter->pdev->dev,
1333		 "Setting VLAN %d, QOS 0x%x on VF %d\n", vlan, qos, vf);
1334	if (test_bit(__IXGBE_DOWN, &adapter->state)) {
1335		dev_warn(&adapter->pdev->dev,
1336			 "The VF VLAN has been set, but the PF device is not up.\n");
1337		dev_warn(&adapter->pdev->dev,
1338			 "Bring the PF device up before attempting to use the VF device.\n");
1339	}
1340
1341out:
1342	return err;
1343}
1344
1345static int ixgbe_disable_port_vlan(struct ixgbe_adapter *adapter, int vf)
1346{
1347	struct ixgbe_hw *hw = &adapter->hw;
1348	int err;
1349
1350	err = ixgbe_set_vf_vlan(adapter, false,
1351				adapter->vfinfo[vf].pf_vlan, vf);
1352	/* Restore tagless access via VLAN 0 */
1353	ixgbe_set_vf_vlan(adapter, true, 0, vf);
1354	ixgbe_clear_vmvir(adapter, vf);
1355	ixgbe_set_vmolr(hw, vf, true);
1356	hw->mac.ops.set_vlan_anti_spoofing(hw, false, vf);
1357	if (adapter->vfinfo[vf].vlan_count)
1358		adapter->vfinfo[vf].vlan_count--;
1359
1360	/* disable hide VLAN on X550 */
1361	if (hw->mac.type >= ixgbe_mac_X550)
1362		ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE);
1363
1364	adapter->vfinfo[vf].pf_vlan = 0;
1365	adapter->vfinfo[vf].pf_qos = 0;
1366
1367	return err;
1368}
1369
1370int ixgbe_ndo_set_vf_vlan(struct net_device *netdev, int vf, u16 vlan, u8 qos)
1371{
1372	int err = 0;
1373	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1374
1375	if ((vf >= adapter->num_vfs) || (vlan > 4095) || (qos > 7))
1376		return -EINVAL;
1377	if (vlan || qos) {
1378		/* Check if there is already a port VLAN set, if so
1379		 * we have to delete the old one first before we
1380		 * can set the new one.  The usage model had
1381		 * previously assumed the user would delete the
1382		 * old port VLAN before setting a new one but this
1383		 * is not necessarily the case.
1384		 */
1385		if (adapter->vfinfo[vf].pf_vlan)
1386			err = ixgbe_disable_port_vlan(adapter, vf);
1387		if (err)
1388			goto out;
1389		err = ixgbe_enable_port_vlan(adapter, vf, vlan, qos);
1390	} else {
1391		err = ixgbe_disable_port_vlan(adapter, vf);
1392	}
1393
1394out:
1395	return err;
1396}
1397
1398static int ixgbe_link_mbps(struct ixgbe_adapter *adapter)
1399{
1400	switch (adapter->link_speed) {
1401	case IXGBE_LINK_SPEED_100_FULL:
1402		return 100;
1403	case IXGBE_LINK_SPEED_1GB_FULL:
1404		return 1000;
1405	case IXGBE_LINK_SPEED_10GB_FULL:
1406		return 10000;
1407	default:
1408		return 0;
1409	}
1410}
1411
1412static void ixgbe_set_vf_rate_limit(struct ixgbe_adapter *adapter, int vf)
1413{
1414	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
1415	struct ixgbe_hw *hw = &adapter->hw;
1416	u32 bcnrc_val = 0;
1417	u16 queue, queues_per_pool;
1418	u16 tx_rate = adapter->vfinfo[vf].tx_rate;
1419
1420	if (tx_rate) {
1421		/* start with base link speed value */
1422		bcnrc_val = adapter->vf_rate_link_speed;
1423
1424		/* Calculate the rate factor values to set */
1425		bcnrc_val <<= IXGBE_RTTBCNRC_RF_INT_SHIFT;
1426		bcnrc_val /= tx_rate;
1427
1428		/* clear everything but the rate factor */
1429		bcnrc_val &= IXGBE_RTTBCNRC_RF_INT_MASK |
1430			     IXGBE_RTTBCNRC_RF_DEC_MASK;
1431
1432		/* enable the rate scheduler */
1433		bcnrc_val |= IXGBE_RTTBCNRC_RS_ENA;
1434	}
1435
1436	/*
1437	 * Set global transmit compensation time to the MMW_SIZE in RTTBCNRM
1438	 * register. Typically MMW_SIZE=0x014 if 9728-byte jumbo is supported
1439	 * and 0x004 otherwise.
1440	 */
1441	switch (hw->mac.type) {
1442	case ixgbe_mac_82599EB:
1443		IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRM, 0x4);
1444		break;
1445	case ixgbe_mac_X540:
1446		IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRM, 0x14);
1447		break;
1448	default:
1449		break;
1450	}
1451
1452	/* determine how many queues per pool based on VMDq mask */
1453	queues_per_pool = __ALIGN_MASK(1, ~vmdq->mask);
1454
1455	/* write value for all Tx queues belonging to VF */
1456	for (queue = 0; queue < queues_per_pool; queue++) {
1457		unsigned int reg_idx = (vf * queues_per_pool) + queue;
1458
1459		IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, reg_idx);
1460		IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, bcnrc_val);
1461	}
1462}
1463
1464void ixgbe_check_vf_rate_limit(struct ixgbe_adapter *adapter)
1465{
1466	int i;
1467
1468	/* VF Tx rate limit was not set */
1469	if (!adapter->vf_rate_link_speed)
1470		return;
1471
1472	if (ixgbe_link_mbps(adapter) != adapter->vf_rate_link_speed) {
1473		adapter->vf_rate_link_speed = 0;
1474		dev_info(&adapter->pdev->dev,
1475			 "Link speed has been changed. VF Transmit rate is disabled\n");
1476	}
1477
1478	for (i = 0; i < adapter->num_vfs; i++) {
1479		if (!adapter->vf_rate_link_speed)
1480			adapter->vfinfo[i].tx_rate = 0;
1481
1482		ixgbe_set_vf_rate_limit(adapter, i);
1483	}
1484}
1485
1486int ixgbe_ndo_set_vf_bw(struct net_device *netdev, int vf, int min_tx_rate,
1487			int max_tx_rate)
1488{
1489	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1490	int link_speed;
1491
1492	/* verify VF is active */
1493	if (vf >= adapter->num_vfs)
1494		return -EINVAL;
1495
1496	/* verify link is up */
1497	if (!adapter->link_up)
1498		return -EINVAL;
1499
1500	/* verify we are linked at 10Gbps */
1501	link_speed = ixgbe_link_mbps(adapter);
1502	if (link_speed != 10000)
1503		return -EINVAL;
1504
1505	if (min_tx_rate)
1506		return -EINVAL;
1507
1508	/* rate limit cannot be less than 10Mbs or greater than link speed */
1509	if (max_tx_rate && ((max_tx_rate <= 10) || (max_tx_rate > link_speed)))
1510		return -EINVAL;
1511
1512	/* store values */
1513	adapter->vf_rate_link_speed = link_speed;
1514	adapter->vfinfo[vf].tx_rate = max_tx_rate;
1515
1516	/* update hardware configuration */
1517	ixgbe_set_vf_rate_limit(adapter, vf);
1518
1519	return 0;
1520}
1521
1522int ixgbe_ndo_set_vf_spoofchk(struct net_device *netdev, int vf, bool setting)
1523{
1524	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1525	int vf_target_reg = vf >> 3;
1526	int vf_target_shift = vf % 8;
1527	struct ixgbe_hw *hw = &adapter->hw;
1528	u32 regval;
1529
1530	if (vf >= adapter->num_vfs)
1531		return -EINVAL;
1532
1533	adapter->vfinfo[vf].spoofchk_enabled = setting;
1534
1535	regval = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
1536	regval &= ~(1 << vf_target_shift);
1537	regval |= (setting << vf_target_shift);
1538	IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), regval);
1539
1540	if (adapter->vfinfo[vf].vlan_count) {
1541		vf_target_shift += IXGBE_SPOOF_VLANAS_SHIFT;
1542		regval = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
1543		regval &= ~(1 << vf_target_shift);
1544		regval |= (setting << vf_target_shift);
1545		IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), regval);
1546	}
1547
1548	return 0;
1549}
1550
1551int ixgbe_ndo_set_vf_rss_query_en(struct net_device *netdev, int vf,
1552				  bool setting)
1553{
1554	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1555
1556	/* This operation is currently supported only for 82599 and x540
1557	 * devices.
1558	 */
1559	if (adapter->hw.mac.type < ixgbe_mac_82599EB ||
1560	    adapter->hw.mac.type >= ixgbe_mac_X550)
1561		return -EOPNOTSUPP;
1562
1563	if (vf >= adapter->num_vfs)
1564		return -EINVAL;
1565
1566	adapter->vfinfo[vf].rss_query_enabled = setting;
1567
1568	return 0;
1569}
1570
1571int ixgbe_ndo_set_vf_trust(struct net_device *netdev, int vf, bool setting)
1572{
1573	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1574
1575	if (vf >= adapter->num_vfs)
1576		return -EINVAL;
1577
1578	/* nothing to do */
1579	if (adapter->vfinfo[vf].trusted == setting)
1580		return 0;
1581
1582	adapter->vfinfo[vf].trusted = setting;
1583
1584	/* reset VF to reconfigure features */
1585	adapter->vfinfo[vf].clear_to_send = false;
1586	ixgbe_ping_vf(adapter, vf);
1587
1588	e_info(drv, "VF %u is %strusted\n", vf, setting ? "" : "not ");
1589
1590	return 0;
1591}
1592
1593int ixgbe_ndo_get_vf_config(struct net_device *netdev,
1594			    int vf, struct ifla_vf_info *ivi)
1595{
1596	struct ixgbe_adapter *adapter = netdev_priv(netdev);
1597	if (vf >= adapter->num_vfs)
1598		return -EINVAL;
1599	ivi->vf = vf;
1600	memcpy(&ivi->mac, adapter->vfinfo[vf].vf_mac_addresses, ETH_ALEN);
1601	ivi->max_tx_rate = adapter->vfinfo[vf].tx_rate;
1602	ivi->min_tx_rate = 0;
1603	ivi->vlan = adapter->vfinfo[vf].pf_vlan;
1604	ivi->qos = adapter->vfinfo[vf].pf_qos;
1605	ivi->spoofchk = adapter->vfinfo[vf].spoofchk_enabled;
1606	ivi->rss_query_en = adapter->vfinfo[vf].rss_query_enabled;
1607	ivi->trusted = adapter->vfinfo[vf].trusted;
1608	return 0;
1609}