Loading...
1/*
2 * Generic Generic NCR5380 driver
3 *
4 * Copyright 1993, Drew Eckhardt
5 * Visionary Computing
6 * (Unix and Linux consulting and custom programming)
7 * drew@colorado.edu
8 * +1 (303) 440-4894
9 *
10 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
11 * K.Lentin@cs.monash.edu.au
12 *
13 * NCR53C400A extensions (c) 1996, Ingmar Baumgart
14 * ingmar@gonzo.schwaben.de
15 *
16 * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg
17 * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl
18 *
19 * Added ISAPNP support for DTC436 adapters,
20 * Thomas Sailer, sailer@ife.ee.ethz.ch
21 *
22 * ALPHA RELEASE 1.
23 *
24 * For more information, please consult
25 *
26 * NCR 5380 Family
27 * SCSI Protocol Controller
28 * Databook
29 *
30 * NCR Microelectronics
31 * 1635 Aeroplaza Drive
32 * Colorado Springs, CO 80916
33 * 1+ (719) 578-3400
34 * 1+ (800) 334-5454
35 */
36
37/*
38 * TODO : flesh out DMA support, find some one actually using this (I have
39 * a memory mapped Trantor board that works fine)
40 */
41
42/*
43 * Options :
44 *
45 * PARITY - enable parity checking. Not supported.
46 *
47 * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
48 *
49 * USLEEP - enable support for devices that don't disconnect. Untested.
50 *
51 * The card is detected and initialized in one of several ways :
52 * 1. With command line overrides - NCR5380=port,irq may be
53 * used on the LILO command line to override the defaults.
54 *
55 * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is
56 * specified as an array of address, irq, dma, board tuples. Ie, for
57 * one board at 0x350, IRQ5, no dma, I could say
58 * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}
59 *
60 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an
61 * IRQ line if overridden on the command line.
62 *
63 * 3. When included as a module, with arguments passed on the command line:
64 * ncr_irq=xx the interrupt
65 * ncr_addr=xx the port or base address (for port or memory
66 * mapped, resp.)
67 * ncr_dma=xx the DMA
68 * ncr_5380=1 to set up for a NCR5380 board
69 * ncr_53c400=1 to set up for a NCR53C400 board
70 * e.g.
71 * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
72 * for a port mapped NCR5380 board or
73 * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
74 * for a memory mapped NCR53C400 board with interrupts disabled.
75 *
76 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an
77 * IRQ line if overridden on the command line.
78 *
79 */
80
81/*
82 * $Log: generic_NCR5380.c,v $
83 */
84
85/* settings for DTC3181E card with only Mustek scanner attached */
86#define USLEEP
87#define USLEEP_POLL 1
88#define USLEEP_SLEEP 20
89#define USLEEP_WAITLONG 500
90
91#define AUTOPROBE_IRQ
92#define AUTOSENSE
93
94
95#ifdef CONFIG_SCSI_GENERIC_NCR53C400
96#define NCR53C400_PSEUDO_DMA 1
97#define PSEUDO_DMA
98#define NCR53C400
99#define NCR5380_STATS
100#undef NCR5380_STAT_LIMIT
101#endif
102
103#include <asm/system.h>
104#include <asm/io.h>
105#include <linux/signal.h>
106#include <linux/blkdev.h>
107#include "scsi.h"
108#include <scsi/scsi_host.h>
109#include "g_NCR5380.h"
110#include "NCR5380.h"
111#include <linux/stat.h>
112#include <linux/init.h>
113#include <linux/ioport.h>
114#include <linux/isapnp.h>
115#include <linux/delay.h>
116#include <linux/interrupt.h>
117
118#define NCR_NOT_SET 0
119static int ncr_irq = NCR_NOT_SET;
120static int ncr_dma = NCR_NOT_SET;
121static int ncr_addr = NCR_NOT_SET;
122static int ncr_5380 = NCR_NOT_SET;
123static int ncr_53c400 = NCR_NOT_SET;
124static int ncr_53c400a = NCR_NOT_SET;
125static int dtc_3181e = NCR_NOT_SET;
126
127static struct override {
128 NCR5380_map_type NCR5380_map_name;
129 int irq;
130 int dma;
131 int board; /* Use NCR53c400, Ricoh, etc. extensions ? */
132} overrides
133#ifdef GENERIC_NCR5380_OVERRIDE
134[] __initdata = GENERIC_NCR5380_OVERRIDE;
135#else
136[1] __initdata = { { 0,},};
137#endif
138
139#define NO_OVERRIDES ARRAY_SIZE(overrides)
140
141#ifndef MODULE
142
143/**
144 * internal_setup - handle lilo command string override
145 * @board: BOARD_* identifier for the board
146 * @str: unused
147 * @ints: numeric parameters
148 *
149 * Do LILO command line initialization of the overrides array. Display
150 * errors when needed
151 *
152 * Locks: none
153 */
154
155static void __init internal_setup(int board, char *str, int *ints)
156{
157 static int commandline_current = 0;
158 switch (board) {
159 case BOARD_NCR5380:
160 if (ints[0] != 2 && ints[0] != 3) {
161 printk(KERN_ERR "generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");
162 return;
163 }
164 break;
165 case BOARD_NCR53C400:
166 if (ints[0] != 2) {
167 printk(KERN_ERR "generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");
168 return;
169 }
170 break;
171 case BOARD_NCR53C400A:
172 if (ints[0] != 2) {
173 printk(KERN_ERR "generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n");
174 return;
175 }
176 break;
177 case BOARD_DTC3181E:
178 if (ints[0] != 2) {
179 printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n");
180 return;
181 }
182 break;
183 }
184
185 if (commandline_current < NO_OVERRIDES) {
186 overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type) ints[1];
187 overrides[commandline_current].irq = ints[2];
188 if (ints[0] == 3)
189 overrides[commandline_current].dma = ints[3];
190 else
191 overrides[commandline_current].dma = DMA_NONE;
192 overrides[commandline_current].board = board;
193 ++commandline_current;
194 }
195}
196
197
198/**
199 * do_NCR53C80_setup - set up entry point
200 * @str: unused
201 *
202 * Setup function invoked at boot to parse the ncr5380= command
203 * line.
204 */
205
206static int __init do_NCR5380_setup(char *str)
207{
208 int ints[10];
209
210 get_options(str, ARRAY_SIZE(ints), ints);
211 internal_setup(BOARD_NCR5380, str, ints);
212 return 1;
213}
214
215/**
216 * do_NCR53C400_setup - set up entry point
217 * @str: unused
218 * @ints: integer parameters from kernel setup code
219 *
220 * Setup function invoked at boot to parse the ncr53c400= command
221 * line.
222 */
223
224static int __init do_NCR53C400_setup(char *str)
225{
226 int ints[10];
227
228 get_options(str, ARRAY_SIZE(ints), ints);
229 internal_setup(BOARD_NCR53C400, str, ints);
230 return 1;
231}
232
233/**
234 * do_NCR53C400A_setup - set up entry point
235 * @str: unused
236 * @ints: integer parameters from kernel setup code
237 *
238 * Setup function invoked at boot to parse the ncr53c400a= command
239 * line.
240 */
241
242static int __init do_NCR53C400A_setup(char *str)
243{
244 int ints[10];
245
246 get_options(str, ARRAY_SIZE(ints), ints);
247 internal_setup(BOARD_NCR53C400A, str, ints);
248 return 1;
249}
250
251/**
252 * do_DTC3181E_setup - set up entry point
253 * @str: unused
254 * @ints: integer parameters from kernel setup code
255 *
256 * Setup function invoked at boot to parse the dtc3181e= command
257 * line.
258 */
259
260static int __init do_DTC3181E_setup(char *str)
261{
262 int ints[10];
263
264 get_options(str, ARRAY_SIZE(ints), ints);
265 internal_setup(BOARD_DTC3181E, str, ints);
266 return 1;
267}
268
269#endif
270
271/**
272 * generic_NCR5380_detect - look for NCR5380 controllers
273 * @tpnt: the scsi template
274 *
275 * Scan for the present of NCR5380, NCR53C400, NCR53C400A, DTC3181E
276 * and DTC436(ISAPnP) controllers. If overrides have been set we use
277 * them.
278 *
279 * The caller supplied NCR5380_init function is invoked from here, before
280 * the interrupt line is taken.
281 *
282 * Locks: none
283 */
284
285int __init generic_NCR5380_detect(struct scsi_host_template * tpnt)
286{
287 static int current_override = 0;
288 int count;
289 unsigned int *ports;
290#ifndef SCSI_G_NCR5380_MEM
291 int i;
292 unsigned long region_size = 16;
293#endif
294 static unsigned int __initdata ncr_53c400a_ports[] = {
295 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
296 };
297 static unsigned int __initdata dtc_3181e_ports[] = {
298 0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0
299 };
300 int flags = 0;
301 struct Scsi_Host *instance;
302#ifdef SCSI_G_NCR5380_MEM
303 unsigned long base;
304 void __iomem *iomem;
305#endif
306
307 if (ncr_irq != NCR_NOT_SET)
308 overrides[0].irq = ncr_irq;
309 if (ncr_dma != NCR_NOT_SET)
310 overrides[0].dma = ncr_dma;
311 if (ncr_addr != NCR_NOT_SET)
312 overrides[0].NCR5380_map_name = (NCR5380_map_type) ncr_addr;
313 if (ncr_5380 != NCR_NOT_SET)
314 overrides[0].board = BOARD_NCR5380;
315 else if (ncr_53c400 != NCR_NOT_SET)
316 overrides[0].board = BOARD_NCR53C400;
317 else if (ncr_53c400a != NCR_NOT_SET)
318 overrides[0].board = BOARD_NCR53C400A;
319 else if (dtc_3181e != NCR_NOT_SET)
320 overrides[0].board = BOARD_DTC3181E;
321#ifndef SCSI_G_NCR5380_MEM
322 if (!current_override && isapnp_present()) {
323 struct pnp_dev *dev = NULL;
324 count = 0;
325 while ((dev = pnp_find_dev(NULL, ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e), dev))) {
326 if (count >= NO_OVERRIDES)
327 break;
328 if (pnp_device_attach(dev) < 0)
329 continue;
330 if (pnp_activate_dev(dev) < 0) {
331 printk(KERN_ERR "dtc436e probe: activate failed\n");
332 pnp_device_detach(dev);
333 continue;
334 }
335 if (!pnp_port_valid(dev, 0)) {
336 printk(KERN_ERR "dtc436e probe: no valid port\n");
337 pnp_device_detach(dev);
338 continue;
339 }
340 if (pnp_irq_valid(dev, 0))
341 overrides[count].irq = pnp_irq(dev, 0);
342 else
343 overrides[count].irq = SCSI_IRQ_NONE;
344 if (pnp_dma_valid(dev, 0))
345 overrides[count].dma = pnp_dma(dev, 0);
346 else
347 overrides[count].dma = DMA_NONE;
348 overrides[count].NCR5380_map_name = (NCR5380_map_type) pnp_port_start(dev, 0);
349 overrides[count].board = BOARD_DTC3181E;
350 count++;
351 }
352 }
353#endif
354 tpnt->proc_name = "g_NCR5380";
355
356 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
357 if (!(overrides[current_override].NCR5380_map_name))
358 continue;
359
360 ports = NULL;
361 switch (overrides[current_override].board) {
362 case BOARD_NCR5380:
363 flags = FLAG_NO_PSEUDO_DMA;
364 break;
365 case BOARD_NCR53C400:
366 flags = FLAG_NCR53C400;
367 break;
368 case BOARD_NCR53C400A:
369 flags = FLAG_NO_PSEUDO_DMA;
370 ports = ncr_53c400a_ports;
371 break;
372 case BOARD_DTC3181E:
373 flags = FLAG_NO_PSEUDO_DMA | FLAG_DTC3181E;
374 ports = dtc_3181e_ports;
375 break;
376 }
377
378#ifndef SCSI_G_NCR5380_MEM
379 if (ports) {
380 /* wakeup sequence for the NCR53C400A and DTC3181E */
381
382 /* Disable the adapter and look for a free io port */
383 outb(0x59, 0x779);
384 outb(0xb9, 0x379);
385 outb(0xc5, 0x379);
386 outb(0xae, 0x379);
387 outb(0xa6, 0x379);
388 outb(0x00, 0x379);
389
390 if (overrides[current_override].NCR5380_map_name != PORT_AUTO)
391 for (i = 0; ports[i]; i++) {
392 if (!request_region(ports[i], 16, "ncr53c80"))
393 continue;
394 if (overrides[current_override].NCR5380_map_name == ports[i])
395 break;
396 release_region(ports[i], 16);
397 } else
398 for (i = 0; ports[i]; i++) {
399 if (!request_region(ports[i], 16, "ncr53c80"))
400 continue;
401 if (inb(ports[i]) == 0xff)
402 break;
403 release_region(ports[i], 16);
404 }
405 if (ports[i]) {
406 /* At this point we have our region reserved */
407 outb(0x59, 0x779);
408 outb(0xb9, 0x379);
409 outb(0xc5, 0x379);
410 outb(0xae, 0x379);
411 outb(0xa6, 0x379);
412 outb(0x80 | i, 0x379); /* set io port to be used */
413 outb(0xc0, ports[i] + 9);
414 if (inb(ports[i] + 9) != 0x80)
415 continue;
416 else
417 overrides[current_override].NCR5380_map_name = ports[i];
418 } else
419 continue;
420 }
421 else
422 {
423 /* Not a 53C400A style setup - just grab */
424 if(!(request_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380")))
425 continue;
426 region_size = NCR5380_region_size;
427 }
428#else
429 base = overrides[current_override].NCR5380_map_name;
430 if (!request_mem_region(base, NCR5380_region_size, "ncr5380"))
431 continue;
432 iomem = ioremap(base, NCR5380_region_size);
433 if (!iomem) {
434 release_mem_region(base, NCR5380_region_size);
435 continue;
436 }
437#endif
438 instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
439 if (instance == NULL) {
440#ifndef SCSI_G_NCR5380_MEM
441 release_region(overrides[current_override].NCR5380_map_name, region_size);
442#else
443 iounmap(iomem);
444 release_mem_region(base, NCR5380_region_size);
445#endif
446 continue;
447 }
448
449 instance->NCR5380_instance_name = overrides[current_override].NCR5380_map_name;
450#ifndef SCSI_G_NCR5380_MEM
451 instance->n_io_port = region_size;
452#else
453 ((struct NCR5380_hostdata *)instance->hostdata)->iomem = iomem;
454#endif
455
456 NCR5380_init(instance, flags);
457
458 if (overrides[current_override].irq != IRQ_AUTO)
459 instance->irq = overrides[current_override].irq;
460 else
461 instance->irq = NCR5380_probe_irq(instance, 0xffff);
462
463 if (instance->irq != SCSI_IRQ_NONE)
464 if (request_irq(instance->irq, generic_NCR5380_intr,
465 IRQF_DISABLED, "NCR5380", instance)) {
466 printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
467 instance->irq = SCSI_IRQ_NONE;
468 }
469
470 if (instance->irq == SCSI_IRQ_NONE) {
471 printk(KERN_INFO "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
472 printk(KERN_INFO "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
473 }
474
475 printk(KERN_INFO "scsi%d : at " STRVAL(NCR5380_map_name) " 0x%x", instance->host_no, (unsigned int) instance->NCR5380_instance_name);
476 if (instance->irq == SCSI_IRQ_NONE)
477 printk(" interrupts disabled");
478 else
479 printk(" irq %d", instance->irq);
480 printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, GENERIC_NCR5380_PUBLIC_RELEASE);
481 NCR5380_print_options(instance);
482 printk("\n");
483
484 ++current_override;
485 ++count;
486 }
487 return count;
488}
489
490/**
491 * generic_NCR5380_info - reporting string
492 * @host: NCR5380 to report on
493 *
494 * Report driver information for the NCR5380
495 */
496
497const char *generic_NCR5380_info(struct Scsi_Host *host)
498{
499 static const char string[] = "Generic NCR5380/53C400 Driver";
500 return string;
501}
502
503/**
504 * generic_NCR5380_release_resources - free resources
505 * @instance: host adapter to clean up
506 *
507 * Free the generic interface resources from this adapter.
508 *
509 * Locks: none
510 */
511
512int generic_NCR5380_release_resources(struct Scsi_Host *instance)
513{
514 NCR5380_local_declare();
515 NCR5380_setup(instance);
516
517 if (instance->irq != SCSI_IRQ_NONE)
518 free_irq(instance->irq, instance);
519 NCR5380_exit(instance);
520
521#ifndef SCSI_G_NCR5380_MEM
522 release_region(instance->NCR5380_instance_name, instance->n_io_port);
523#else
524 iounmap(((struct NCR5380_hostdata *)instance->hostdata)->iomem);
525 release_mem_region(instance->NCR5380_instance_name, NCR5380_region_size);
526#endif
527
528
529 return 0;
530}
531
532#ifdef BIOSPARAM
533/**
534 * generic_NCR5380_biosparam
535 * @disk: disk to compute geometry for
536 * @dev: device identifier for this disk
537 * @ip: sizes to fill in
538 *
539 * Generates a BIOS / DOS compatible H-C-S mapping for the specified
540 * device / size.
541 *
542 * XXX Most SCSI boards use this mapping, I could be incorrect. Someone
543 * using hard disks on a trantor should verify that this mapping
544 * corresponds to that used by the BIOS / ASPI driver by running the linux
545 * fdisk program and matching the H_C_S coordinates to what DOS uses.
546 *
547 * Locks: none
548 */
549
550static int
551generic_NCR5380_biosparam(struct scsi_device *sdev, struct block_device *bdev,
552 sector_t capacity, int *ip)
553{
554 ip[0] = 64;
555 ip[1] = 32;
556 ip[2] = capacity >> 11;
557 return 0;
558}
559#endif
560
561#ifdef NCR53C400_PSEUDO_DMA
562
563/**
564 * NCR5380_pread - pseudo DMA read
565 * @instance: adapter to read from
566 * @dst: buffer to read into
567 * @len: buffer length
568 *
569 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
570 * controller
571 */
572
573static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
574{
575 int blocks = len / 128;
576 int start = 0;
577 int bl;
578
579 NCR5380_local_declare();
580 NCR5380_setup(instance);
581
582 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE | CSR_TRANS_DIR);
583 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
584 while (1) {
585 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
586 break;
587 }
588 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
589 printk(KERN_ERR "53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
590 return -1;
591 }
592 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY);
593
594#ifndef SCSI_G_NCR5380_MEM
595 {
596 int i;
597 for (i = 0; i < 128; i++)
598 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
599 }
600#else
601 /* implies SCSI_G_NCR5380_MEM */
602 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
603#endif
604 start += 128;
605 blocks--;
606 }
607
608 if (blocks) {
609 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
610 {
611 // FIXME - no timeout
612 }
613
614#ifndef SCSI_G_NCR5380_MEM
615 {
616 int i;
617 for (i = 0; i < 128; i++)
618 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
619 }
620#else
621 /* implies SCSI_G_NCR5380_MEM */
622 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
623#endif
624 start += 128;
625 blocks--;
626 }
627
628 if (!(NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
629 printk("53C400r: no 53C80 gated irq after transfer");
630
631#if 0
632 /*
633 * DON'T DO THIS - THEY NEVER ARRIVE!
634 */
635 printk("53C400r: Waiting for 53C80 registers\n");
636 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG)
637 ;
638#endif
639 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
640 printk(KERN_ERR "53C400r: no end dma signal\n");
641
642 NCR5380_write(MODE_REG, MR_BASE);
643 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
644 return 0;
645}
646
647/**
648 * NCR5380_write - pseudo DMA write
649 * @instance: adapter to read from
650 * @dst: buffer to read into
651 * @len: buffer length
652 *
653 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
654 * controller
655 */
656
657static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
658{
659 int blocks = len / 128;
660 int start = 0;
661 int bl;
662 int i;
663
664 NCR5380_local_declare();
665 NCR5380_setup(instance);
666
667 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);
668 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
669 while (1) {
670 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
671 printk(KERN_ERR "53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
672 return -1;
673 }
674
675 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
676 break;
677 }
678 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
679 ; // FIXME - timeout
680#ifndef SCSI_G_NCR5380_MEM
681 {
682 for (i = 0; i < 128; i++)
683 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
684 }
685#else
686 /* implies SCSI_G_NCR5380_MEM */
687 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
688#endif
689 start += 128;
690 blocks--;
691 }
692 if (blocks) {
693 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
694 ; // FIXME - no timeout
695
696#ifndef SCSI_G_NCR5380_MEM
697 {
698 for (i = 0; i < 128; i++)
699 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
700 }
701#else
702 /* implies SCSI_G_NCR5380_MEM */
703 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
704#endif
705 start += 128;
706 blocks--;
707 }
708
709#if 0
710 printk("53C400w: waiting for registers to be available\n");
711 THEY NEVER DO ! while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG);
712 printk("53C400w: Got em\n");
713#endif
714
715 /* Let's wait for this instead - could be ugly */
716 /* All documentation says to check for this. Maybe my hardware is too
717 * fast. Waiting for it seems to work fine! KLL
718 */
719 while (!(i = NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
720 ; // FIXME - no timeout
721
722 /*
723 * I know. i is certainly != 0 here but the loop is new. See previous
724 * comment.
725 */
726 if (i) {
727 if (!((i = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER))
728 printk(KERN_ERR "53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i);
729 } else
730 printk(KERN_ERR "53C400w: no 53C80 gated irq after transfer (last block)\n");
731
732#if 0
733 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) {
734 printk(KERN_ERR "53C400w: no end dma signal\n");
735 }
736#endif
737 while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
738 ; // TIMEOUT
739 return 0;
740}
741#endif /* PSEUDO_DMA */
742
743/*
744 * Include the NCR5380 core code that we build our driver around
745 */
746
747#include "NCR5380.c"
748
749#define PRINTP(x) len += sprintf(buffer+len, x)
750#define ANDP ,
751
752static int sprint_opcode(char *buffer, int len, int opcode)
753{
754 int start = len;
755 PRINTP("0x%02x " ANDP opcode);
756 return len - start;
757}
758
759static int sprint_command(char *buffer, int len, unsigned char *command)
760{
761 int i, s, start = len;
762 len += sprint_opcode(buffer, len, command[0]);
763 for (i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i)
764 PRINTP("%02x " ANDP command[i]);
765 PRINTP("\n");
766 return len - start;
767}
768
769/**
770 * sprintf_Scsi_Cmnd - print a scsi command
771 * @buffer: buffr to print into
772 * @len: buffer length
773 * @cmd: SCSI command block
774 *
775 * Print out the target and command data in hex
776 */
777
778static int sprint_Scsi_Cmnd(char *buffer, int len, Scsi_Cmnd * cmd)
779{
780 int start = len;
781 PRINTP("host number %d destination target %d, lun %d\n" ANDP cmd->device->host->host_no ANDP cmd->device->id ANDP cmd->device->lun);
782 PRINTP(" command = ");
783 len += sprint_command(buffer, len, cmd->cmnd);
784 return len - start;
785}
786
787/**
788 * generic_NCR5380_proc_info - /proc for NCR5380 driver
789 * @buffer: buffer to print into
790 * @start: start position
791 * @offset: offset into buffer
792 * @len: length
793 * @hostno: instance to affect
794 * @inout: read/write
795 *
796 * Provide the procfs information for the 5380 controller. We fill
797 * this with useful debugging information including the commands
798 * being executed, disconnected command queue and the statistical
799 * data
800 *
801 * Locks: global cli/lock for queue walk
802 */
803
804static int generic_NCR5380_proc_info(struct Scsi_Host *scsi_ptr, char *buffer, char **start, off_t offset, int length, int inout)
805{
806 int len = 0;
807 NCR5380_local_declare();
808 unsigned long flags;
809 unsigned char status;
810 int i;
811 Scsi_Cmnd *ptr;
812 struct NCR5380_hostdata *hostdata;
813#ifdef NCR5380_STATS
814 struct scsi_device *dev;
815#endif
816
817 NCR5380_setup(scsi_ptr);
818 hostdata = (struct NCR5380_hostdata *) scsi_ptr->hostdata;
819
820 spin_lock_irqsave(scsi_ptr->host_lock, flags);
821 PRINTP("SCSI host number %d : %s\n" ANDP scsi_ptr->host_no ANDP scsi_ptr->hostt->name);
822 PRINTP("Generic NCR5380 driver version %d\n" ANDP GENERIC_NCR5380_PUBLIC_RELEASE);
823 PRINTP("NCR5380 core version %d\n" ANDP NCR5380_PUBLIC_RELEASE);
824#ifdef NCR53C400
825 PRINTP("NCR53C400 extension version %d\n" ANDP NCR53C400_PUBLIC_RELEASE);
826 PRINTP("NCR53C400 card%s detected\n" ANDP(((struct NCR5380_hostdata *) scsi_ptr->hostdata)->flags & FLAG_NCR53C400) ? "" : " not");
827# if NCR53C400_PSEUDO_DMA
828 PRINTP("NCR53C400 pseudo DMA used\n");
829# endif
830#else
831 PRINTP("NO NCR53C400 driver extensions\n");
832#endif
833 PRINTP("Using %s mapping at %s 0x%lx, " ANDP STRVAL(NCR5380_map_config) ANDP STRVAL(NCR5380_map_name) ANDP scsi_ptr->NCR5380_instance_name);
834 if (scsi_ptr->irq == SCSI_IRQ_NONE)
835 PRINTP("no interrupt\n");
836 else
837 PRINTP("on interrupt %d\n" ANDP scsi_ptr->irq);
838
839#ifdef NCR5380_STATS
840 if (hostdata->connected || hostdata->issue_queue || hostdata->disconnected_queue)
841 PRINTP("There are commands pending, transfer rates may be crud\n");
842 if (hostdata->pendingr)
843 PRINTP(" %d pending reads" ANDP hostdata->pendingr);
844 if (hostdata->pendingw)
845 PRINTP(" %d pending writes" ANDP hostdata->pendingw);
846 if (hostdata->pendingr || hostdata->pendingw)
847 PRINTP("\n");
848 shost_for_each_device(dev, scsi_ptr) {
849 unsigned long br = hostdata->bytes_read[dev->id];
850 unsigned long bw = hostdata->bytes_write[dev->id];
851 long tr = hostdata->time_read[dev->id] / HZ;
852 long tw = hostdata->time_write[dev->id] / HZ;
853
854 PRINTP(" T:%d %s " ANDP dev->id ANDP scsi_device_type(dev->type));
855 for (i = 0; i < 8; i++)
856 if (dev->vendor[i] >= 0x20)
857 *(buffer + (len++)) = dev->vendor[i];
858 *(buffer + (len++)) = ' ';
859 for (i = 0; i < 16; i++)
860 if (dev->model[i] >= 0x20)
861 *(buffer + (len++)) = dev->model[i];
862 *(buffer + (len++)) = ' ';
863 for (i = 0; i < 4; i++)
864 if (dev->rev[i] >= 0x20)
865 *(buffer + (len++)) = dev->rev[i];
866 *(buffer + (len++)) = ' ';
867
868 PRINTP("\n%10ld kb read in %5ld secs" ANDP br / 1024 ANDP tr);
869 if (tr)
870 PRINTP(" @ %5ld bps" ANDP br / tr);
871
872 PRINTP("\n%10ld kb written in %5ld secs" ANDP bw / 1024 ANDP tw);
873 if (tw)
874 PRINTP(" @ %5ld bps" ANDP bw / tw);
875 PRINTP("\n");
876 }
877#endif
878
879 status = NCR5380_read(STATUS_REG);
880 if (!(status & SR_REQ))
881 PRINTP("REQ not asserted, phase unknown.\n");
882 else {
883 for (i = 0; (phases[i].value != PHASE_UNKNOWN) && (phases[i].value != (status & PHASE_MASK)); ++i);
884 PRINTP("Phase %s\n" ANDP phases[i].name);
885 }
886
887 if (!hostdata->connected) {
888 PRINTP("No currently connected command\n");
889 } else {
890 len += sprint_Scsi_Cmnd(buffer, len, (Scsi_Cmnd *) hostdata->connected);
891 }
892
893 PRINTP("issue_queue\n");
894
895 for (ptr = (Scsi_Cmnd *) hostdata->issue_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
896 len += sprint_Scsi_Cmnd(buffer, len, ptr);
897
898 PRINTP("disconnected_queue\n");
899
900 for (ptr = (Scsi_Cmnd *) hostdata->disconnected_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
901 len += sprint_Scsi_Cmnd(buffer, len, ptr);
902
903 *start = buffer + offset;
904 len -= offset;
905 if (len > length)
906 len = length;
907 spin_unlock_irqrestore(scsi_ptr->host_lock, flags);
908 return len;
909}
910
911#undef PRINTP
912#undef ANDP
913
914static struct scsi_host_template driver_template = {
915 .proc_info = generic_NCR5380_proc_info,
916 .name = "Generic NCR5380/NCR53C400 Scsi Driver",
917 .detect = generic_NCR5380_detect,
918 .release = generic_NCR5380_release_resources,
919 .info = generic_NCR5380_info,
920 .queuecommand = generic_NCR5380_queue_command,
921 .eh_abort_handler = generic_NCR5380_abort,
922 .eh_bus_reset_handler = generic_NCR5380_bus_reset,
923 .bios_param = NCR5380_BIOSPARAM,
924 .can_queue = CAN_QUEUE,
925 .this_id = 7,
926 .sg_tablesize = SG_ALL,
927 .cmd_per_lun = CMD_PER_LUN,
928 .use_clustering = DISABLE_CLUSTERING,
929};
930#include <linux/module.h>
931#include "scsi_module.c"
932
933module_param(ncr_irq, int, 0);
934module_param(ncr_dma, int, 0);
935module_param(ncr_addr, int, 0);
936module_param(ncr_5380, int, 0);
937module_param(ncr_53c400, int, 0);
938module_param(ncr_53c400a, int, 0);
939module_param(dtc_3181e, int, 0);
940MODULE_LICENSE("GPL");
941
942#ifndef SCSI_G_NCR5380_MEM
943static struct isapnp_device_id id_table[] __devinitdata = {
944 {
945 ISAPNP_ANY_ID, ISAPNP_ANY_ID,
946 ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e),
947 0},
948 {0}
949};
950
951MODULE_DEVICE_TABLE(isapnp, id_table);
952#endif
953
954__setup("ncr5380=", do_NCR5380_setup);
955__setup("ncr53c400=", do_NCR53C400_setup);
956__setup("ncr53c400a=", do_NCR53C400A_setup);
957__setup("dtc3181e=", do_DTC3181E_setup);
1/*
2 * Generic Generic NCR5380 driver
3 *
4 * Copyright 1993, Drew Eckhardt
5 * Visionary Computing
6 * (Unix and Linux consulting and custom programming)
7 * drew@colorado.edu
8 * +1 (303) 440-4894
9 *
10 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
11 * K.Lentin@cs.monash.edu.au
12 *
13 * NCR53C400A extensions (c) 1996, Ingmar Baumgart
14 * ingmar@gonzo.schwaben.de
15 *
16 * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg
17 * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl
18 *
19 * Added ISAPNP support for DTC436 adapters,
20 * Thomas Sailer, sailer@ife.ee.ethz.ch
21 */
22
23/*
24 * TODO : flesh out DMA support, find some one actually using this (I have
25 * a memory mapped Trantor board that works fine)
26 */
27
28/*
29 * The card is detected and initialized in one of several ways :
30 * 1. With command line overrides - NCR5380=port,irq may be
31 * used on the LILO command line to override the defaults.
32 *
33 * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is
34 * specified as an array of address, irq, dma, board tuples. Ie, for
35 * one board at 0x350, IRQ5, no dma, I could say
36 * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}
37 *
38 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an
39 * IRQ line if overridden on the command line.
40 *
41 * 3. When included as a module, with arguments passed on the command line:
42 * ncr_irq=xx the interrupt
43 * ncr_addr=xx the port or base address (for port or memory
44 * mapped, resp.)
45 * ncr_dma=xx the DMA
46 * ncr_5380=1 to set up for a NCR5380 board
47 * ncr_53c400=1 to set up for a NCR53C400 board
48 * e.g.
49 * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
50 * for a port mapped NCR5380 board or
51 * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
52 * for a memory mapped NCR53C400 board with interrupts disabled.
53 *
54 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an
55 * IRQ line if overridden on the command line.
56 *
57 */
58
59#define AUTOPROBE_IRQ
60
61#ifdef CONFIG_SCSI_GENERIC_NCR53C400
62#define PSEUDO_DMA
63#endif
64
65#include <asm/io.h>
66#include <linux/blkdev.h>
67#include <linux/module.h>
68#include <scsi/scsi_host.h>
69#include "g_NCR5380.h"
70#include "NCR5380.h"
71#include <linux/init.h>
72#include <linux/ioport.h>
73#include <linux/isapnp.h>
74#include <linux/interrupt.h>
75
76static int ncr_irq;
77static int ncr_dma;
78static int ncr_addr;
79static int ncr_5380;
80static int ncr_53c400;
81static int ncr_53c400a;
82static int dtc_3181e;
83static int hp_c2502;
84
85static struct override {
86 NCR5380_map_type NCR5380_map_name;
87 int irq;
88 int dma;
89 int board; /* Use NCR53c400, Ricoh, etc. extensions ? */
90} overrides
91#ifdef GENERIC_NCR5380_OVERRIDE
92[] __initdata = GENERIC_NCR5380_OVERRIDE;
93#else
94[1] __initdata = { { 0,},};
95#endif
96
97#define NO_OVERRIDES ARRAY_SIZE(overrides)
98
99#ifndef MODULE
100
101/**
102 * internal_setup - handle lilo command string override
103 * @board: BOARD_* identifier for the board
104 * @str: unused
105 * @ints: numeric parameters
106 *
107 * Do LILO command line initialization of the overrides array. Display
108 * errors when needed
109 *
110 * Locks: none
111 */
112
113static void __init internal_setup(int board, char *str, int *ints)
114{
115 static int commandline_current;
116 switch (board) {
117 case BOARD_NCR5380:
118 if (ints[0] != 2 && ints[0] != 3) {
119 printk(KERN_ERR "generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");
120 return;
121 }
122 break;
123 case BOARD_NCR53C400:
124 if (ints[0] != 2) {
125 printk(KERN_ERR "generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");
126 return;
127 }
128 break;
129 case BOARD_NCR53C400A:
130 if (ints[0] != 2) {
131 printk(KERN_ERR "generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n");
132 return;
133 }
134 break;
135 case BOARD_DTC3181E:
136 if (ints[0] != 2) {
137 printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n");
138 return;
139 }
140 break;
141 }
142
143 if (commandline_current < NO_OVERRIDES) {
144 overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type) ints[1];
145 overrides[commandline_current].irq = ints[2];
146 if (ints[0] == 3)
147 overrides[commandline_current].dma = ints[3];
148 else
149 overrides[commandline_current].dma = DMA_NONE;
150 overrides[commandline_current].board = board;
151 ++commandline_current;
152 }
153}
154
155
156/**
157 * do_NCR53C80_setup - set up entry point
158 * @str: unused
159 *
160 * Setup function invoked at boot to parse the ncr5380= command
161 * line.
162 */
163
164static int __init do_NCR5380_setup(char *str)
165{
166 int ints[10];
167
168 get_options(str, ARRAY_SIZE(ints), ints);
169 internal_setup(BOARD_NCR5380, str, ints);
170 return 1;
171}
172
173/**
174 * do_NCR53C400_setup - set up entry point
175 * @str: unused
176 * @ints: integer parameters from kernel setup code
177 *
178 * Setup function invoked at boot to parse the ncr53c400= command
179 * line.
180 */
181
182static int __init do_NCR53C400_setup(char *str)
183{
184 int ints[10];
185
186 get_options(str, ARRAY_SIZE(ints), ints);
187 internal_setup(BOARD_NCR53C400, str, ints);
188 return 1;
189}
190
191/**
192 * do_NCR53C400A_setup - set up entry point
193 * @str: unused
194 * @ints: integer parameters from kernel setup code
195 *
196 * Setup function invoked at boot to parse the ncr53c400a= command
197 * line.
198 */
199
200static int __init do_NCR53C400A_setup(char *str)
201{
202 int ints[10];
203
204 get_options(str, ARRAY_SIZE(ints), ints);
205 internal_setup(BOARD_NCR53C400A, str, ints);
206 return 1;
207}
208
209/**
210 * do_DTC3181E_setup - set up entry point
211 * @str: unused
212 * @ints: integer parameters from kernel setup code
213 *
214 * Setup function invoked at boot to parse the dtc3181e= command
215 * line.
216 */
217
218static int __init do_DTC3181E_setup(char *str)
219{
220 int ints[10];
221
222 get_options(str, ARRAY_SIZE(ints), ints);
223 internal_setup(BOARD_DTC3181E, str, ints);
224 return 1;
225}
226
227#endif
228
229#ifndef SCSI_G_NCR5380_MEM
230/*
231 * Configure I/O address of 53C400A or DTC436 by writing magic numbers
232 * to ports 0x779 and 0x379.
233 */
234static void magic_configure(int idx, u8 irq, u8 magic[])
235{
236 u8 cfg = 0;
237
238 outb(magic[0], 0x779);
239 outb(magic[1], 0x379);
240 outb(magic[2], 0x379);
241 outb(magic[3], 0x379);
242 outb(magic[4], 0x379);
243
244 /* allowed IRQs for HP C2502 */
245 if (irq != 2 && irq != 3 && irq != 4 && irq != 5 && irq != 7)
246 irq = 0;
247 if (idx >= 0 && idx <= 7)
248 cfg = 0x80 | idx | (irq << 4);
249 outb(cfg, 0x379);
250}
251#endif
252
253/**
254 * generic_NCR5380_detect - look for NCR5380 controllers
255 * @tpnt: the scsi template
256 *
257 * Scan for the present of NCR5380, NCR53C400, NCR53C400A, DTC3181E
258 * and DTC436(ISAPnP) controllers. If overrides have been set we use
259 * them.
260 *
261 * Locks: none
262 */
263
264static int __init generic_NCR5380_detect(struct scsi_host_template *tpnt)
265{
266 static int current_override;
267 int count;
268 unsigned int *ports;
269 u8 *magic = NULL;
270#ifndef SCSI_G_NCR5380_MEM
271 int i;
272 int port_idx = -1;
273 unsigned long region_size = 16;
274#endif
275 static unsigned int __initdata ncr_53c400a_ports[] = {
276 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
277 };
278 static unsigned int __initdata dtc_3181e_ports[] = {
279 0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0
280 };
281 static u8 ncr_53c400a_magic[] __initdata = { /* 53C400A & DTC436 */
282 0x59, 0xb9, 0xc5, 0xae, 0xa6
283 };
284 static u8 hp_c2502_magic[] __initdata = { /* HP C2502 */
285 0x0f, 0x22, 0xf0, 0x20, 0x80
286 };
287 int flags;
288 struct Scsi_Host *instance;
289 struct NCR5380_hostdata *hostdata;
290#ifdef SCSI_G_NCR5380_MEM
291 unsigned long base;
292 void __iomem *iomem;
293#endif
294
295 if (ncr_irq)
296 overrides[0].irq = ncr_irq;
297 if (ncr_dma)
298 overrides[0].dma = ncr_dma;
299 if (ncr_addr)
300 overrides[0].NCR5380_map_name = (NCR5380_map_type) ncr_addr;
301 if (ncr_5380)
302 overrides[0].board = BOARD_NCR5380;
303 else if (ncr_53c400)
304 overrides[0].board = BOARD_NCR53C400;
305 else if (ncr_53c400a)
306 overrides[0].board = BOARD_NCR53C400A;
307 else if (dtc_3181e)
308 overrides[0].board = BOARD_DTC3181E;
309 else if (hp_c2502)
310 overrides[0].board = BOARD_HP_C2502;
311#ifndef SCSI_G_NCR5380_MEM
312 if (!current_override && isapnp_present()) {
313 struct pnp_dev *dev = NULL;
314 count = 0;
315 while ((dev = pnp_find_dev(NULL, ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e), dev))) {
316 if (count >= NO_OVERRIDES)
317 break;
318 if (pnp_device_attach(dev) < 0)
319 continue;
320 if (pnp_activate_dev(dev) < 0) {
321 printk(KERN_ERR "dtc436e probe: activate failed\n");
322 pnp_device_detach(dev);
323 continue;
324 }
325 if (!pnp_port_valid(dev, 0)) {
326 printk(KERN_ERR "dtc436e probe: no valid port\n");
327 pnp_device_detach(dev);
328 continue;
329 }
330 if (pnp_irq_valid(dev, 0))
331 overrides[count].irq = pnp_irq(dev, 0);
332 else
333 overrides[count].irq = NO_IRQ;
334 if (pnp_dma_valid(dev, 0))
335 overrides[count].dma = pnp_dma(dev, 0);
336 else
337 overrides[count].dma = DMA_NONE;
338 overrides[count].NCR5380_map_name = (NCR5380_map_type) pnp_port_start(dev, 0);
339 overrides[count].board = BOARD_DTC3181E;
340 count++;
341 }
342 }
343#endif
344
345 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
346 if (!(overrides[current_override].NCR5380_map_name))
347 continue;
348
349 ports = NULL;
350 flags = 0;
351 switch (overrides[current_override].board) {
352 case BOARD_NCR5380:
353 flags = FLAG_NO_PSEUDO_DMA;
354 break;
355 case BOARD_NCR53C400:
356#ifdef PSEUDO_DMA
357 flags = FLAG_NO_DMA_FIXUP;
358#endif
359 break;
360 case BOARD_NCR53C400A:
361 flags = FLAG_NO_DMA_FIXUP;
362 ports = ncr_53c400a_ports;
363 magic = ncr_53c400a_magic;
364 break;
365 case BOARD_HP_C2502:
366 flags = FLAG_NO_DMA_FIXUP;
367 ports = ncr_53c400a_ports;
368 magic = hp_c2502_magic;
369 break;
370 case BOARD_DTC3181E:
371 flags = FLAG_NO_DMA_FIXUP;
372 ports = dtc_3181e_ports;
373 magic = ncr_53c400a_magic;
374 break;
375 }
376
377#ifndef SCSI_G_NCR5380_MEM
378 if (ports && magic) {
379 /* wakeup sequence for the NCR53C400A and DTC3181E */
380
381 /* Disable the adapter and look for a free io port */
382 magic_configure(-1, 0, magic);
383
384 if (overrides[current_override].NCR5380_map_name != PORT_AUTO)
385 for (i = 0; ports[i]; i++) {
386 if (!request_region(ports[i], 16, "ncr53c80"))
387 continue;
388 if (overrides[current_override].NCR5380_map_name == ports[i])
389 break;
390 release_region(ports[i], 16);
391 } else
392 for (i = 0; ports[i]; i++) {
393 if (!request_region(ports[i], 16, "ncr53c80"))
394 continue;
395 if (inb(ports[i]) == 0xff)
396 break;
397 release_region(ports[i], 16);
398 }
399 if (ports[i]) {
400 /* At this point we have our region reserved */
401 magic_configure(i, 0, magic); /* no IRQ yet */
402 outb(0xc0, ports[i] + 9);
403 if (inb(ports[i] + 9) != 0x80)
404 continue;
405 overrides[current_override].NCR5380_map_name = ports[i];
406 port_idx = i;
407 } else
408 continue;
409 }
410 else
411 {
412 /* Not a 53C400A style setup - just grab */
413 if(!(request_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380")))
414 continue;
415 region_size = NCR5380_region_size;
416 }
417#else
418 base = overrides[current_override].NCR5380_map_name;
419 if (!request_mem_region(base, NCR5380_region_size, "ncr5380"))
420 continue;
421 iomem = ioremap(base, NCR5380_region_size);
422 if (!iomem) {
423 release_mem_region(base, NCR5380_region_size);
424 continue;
425 }
426#endif
427 instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
428 if (instance == NULL)
429 goto out_release;
430 hostdata = shost_priv(instance);
431
432#ifndef SCSI_G_NCR5380_MEM
433 instance->io_port = overrides[current_override].NCR5380_map_name;
434 instance->n_io_port = region_size;
435 hostdata->io_width = 1; /* 8-bit PDMA by default */
436
437 /*
438 * On NCR53C400 boards, NCR5380 registers are mapped 8 past
439 * the base address.
440 */
441 switch (overrides[current_override].board) {
442 case BOARD_NCR53C400:
443 instance->io_port += 8;
444 hostdata->c400_ctl_status = 0;
445 hostdata->c400_blk_cnt = 1;
446 hostdata->c400_host_buf = 4;
447 break;
448 case BOARD_DTC3181E:
449 hostdata->io_width = 2; /* 16-bit PDMA */
450 /* fall through */
451 case BOARD_NCR53C400A:
452 case BOARD_HP_C2502:
453 hostdata->c400_ctl_status = 9;
454 hostdata->c400_blk_cnt = 10;
455 hostdata->c400_host_buf = 8;
456 break;
457 }
458#else
459 instance->base = overrides[current_override].NCR5380_map_name;
460 hostdata->iomem = iomem;
461 switch (overrides[current_override].board) {
462 case BOARD_NCR53C400:
463 hostdata->c400_ctl_status = 0x100;
464 hostdata->c400_blk_cnt = 0x101;
465 hostdata->c400_host_buf = 0x104;
466 break;
467 case BOARD_DTC3181E:
468 case BOARD_NCR53C400A:
469 case BOARD_HP_C2502:
470 pr_err(DRV_MODULE_NAME ": unknown register offsets\n");
471 goto out_unregister;
472 }
473#endif
474
475 if (NCR5380_init(instance, flags))
476 goto out_unregister;
477
478 switch (overrides[current_override].board) {
479 case BOARD_NCR53C400:
480 case BOARD_DTC3181E:
481 case BOARD_NCR53C400A:
482 case BOARD_HP_C2502:
483 NCR5380_write(hostdata->c400_ctl_status, CSR_BASE);
484 }
485
486 NCR5380_maybe_reset_bus(instance);
487
488 if (overrides[current_override].irq != IRQ_AUTO)
489 instance->irq = overrides[current_override].irq;
490 else
491 instance->irq = NCR5380_probe_irq(instance, 0xffff);
492
493 /* Compatibility with documented NCR5380 kernel parameters */
494 if (instance->irq == 255)
495 instance->irq = NO_IRQ;
496
497 if (instance->irq != NO_IRQ) {
498#ifndef SCSI_G_NCR5380_MEM
499 /* set IRQ for HP C2502 */
500 if (overrides[current_override].board == BOARD_HP_C2502)
501 magic_configure(port_idx, instance->irq, magic);
502#endif
503 if (request_irq(instance->irq, generic_NCR5380_intr,
504 0, "NCR5380", instance)) {
505 printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
506 instance->irq = NO_IRQ;
507 }
508 }
509
510 if (instance->irq == NO_IRQ) {
511 printk(KERN_INFO "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
512 printk(KERN_INFO "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
513 }
514
515 ++current_override;
516 ++count;
517 }
518 return count;
519
520out_unregister:
521 scsi_unregister(instance);
522out_release:
523#ifndef SCSI_G_NCR5380_MEM
524 release_region(overrides[current_override].NCR5380_map_name, region_size);
525#else
526 iounmap(iomem);
527 release_mem_region(base, NCR5380_region_size);
528#endif
529 return count;
530}
531
532/**
533 * generic_NCR5380_release_resources - free resources
534 * @instance: host adapter to clean up
535 *
536 * Free the generic interface resources from this adapter.
537 *
538 * Locks: none
539 */
540
541static int generic_NCR5380_release_resources(struct Scsi_Host *instance)
542{
543 if (instance->irq != NO_IRQ)
544 free_irq(instance->irq, instance);
545 NCR5380_exit(instance);
546#ifndef SCSI_G_NCR5380_MEM
547 release_region(instance->io_port, instance->n_io_port);
548#else
549 iounmap(((struct NCR5380_hostdata *)instance->hostdata)->iomem);
550 release_mem_region(instance->base, NCR5380_region_size);
551#endif
552 return 0;
553}
554
555#ifdef BIOSPARAM
556/**
557 * generic_NCR5380_biosparam
558 * @disk: disk to compute geometry for
559 * @dev: device identifier for this disk
560 * @ip: sizes to fill in
561 *
562 * Generates a BIOS / DOS compatible H-C-S mapping for the specified
563 * device / size.
564 *
565 * XXX Most SCSI boards use this mapping, I could be incorrect. Someone
566 * using hard disks on a trantor should verify that this mapping
567 * corresponds to that used by the BIOS / ASPI driver by running the linux
568 * fdisk program and matching the H_C_S coordinates to what DOS uses.
569 *
570 * Locks: none
571 */
572
573static int
574generic_NCR5380_biosparam(struct scsi_device *sdev, struct block_device *bdev,
575 sector_t capacity, int *ip)
576{
577 ip[0] = 64;
578 ip[1] = 32;
579 ip[2] = capacity >> 11;
580 return 0;
581}
582#endif
583
584#ifdef PSEUDO_DMA
585
586/**
587 * NCR5380_pread - pseudo DMA read
588 * @instance: adapter to read from
589 * @dst: buffer to read into
590 * @len: buffer length
591 *
592 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
593 * controller
594 */
595
596static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
597{
598 struct NCR5380_hostdata *hostdata = shost_priv(instance);
599 int blocks = len / 128;
600 int start = 0;
601
602 NCR5380_write(hostdata->c400_ctl_status, CSR_BASE | CSR_TRANS_DIR);
603 NCR5380_write(hostdata->c400_blk_cnt, blocks);
604 while (1) {
605 if (NCR5380_read(hostdata->c400_blk_cnt) == 0)
606 break;
607 if (NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ) {
608 printk(KERN_ERR "53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
609 return -1;
610 }
611 while (NCR5380_read(hostdata->c400_ctl_status) & CSR_HOST_BUF_NOT_RDY)
612 ; /* FIXME - no timeout */
613
614#ifndef SCSI_G_NCR5380_MEM
615 if (hostdata->io_width == 2)
616 insw(instance->io_port + hostdata->c400_host_buf,
617 dst + start, 64);
618 else
619 insb(instance->io_port + hostdata->c400_host_buf,
620 dst + start, 128);
621#else
622 /* implies SCSI_G_NCR5380_MEM */
623 memcpy_fromio(dst + start,
624 hostdata->iomem + NCR53C400_host_buffer, 128);
625#endif
626 start += 128;
627 blocks--;
628 }
629
630 if (blocks) {
631 while (NCR5380_read(hostdata->c400_ctl_status) & CSR_HOST_BUF_NOT_RDY)
632 ; /* FIXME - no timeout */
633
634#ifndef SCSI_G_NCR5380_MEM
635 if (hostdata->io_width == 2)
636 insw(instance->io_port + hostdata->c400_host_buf,
637 dst + start, 64);
638 else
639 insb(instance->io_port + hostdata->c400_host_buf,
640 dst + start, 128);
641#else
642 /* implies SCSI_G_NCR5380_MEM */
643 memcpy_fromio(dst + start,
644 hostdata->iomem + NCR53C400_host_buffer, 128);
645#endif
646 start += 128;
647 blocks--;
648 }
649
650 if (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ))
651 printk("53C400r: no 53C80 gated irq after transfer");
652
653 /* wait for 53C80 registers to be available */
654 while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG))
655 ;
656
657 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
658 printk(KERN_ERR "53C400r: no end dma signal\n");
659
660 return 0;
661}
662
663/**
664 * NCR5380_write - pseudo DMA write
665 * @instance: adapter to read from
666 * @dst: buffer to read into
667 * @len: buffer length
668 *
669 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
670 * controller
671 */
672
673static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
674{
675 struct NCR5380_hostdata *hostdata = shost_priv(instance);
676 int blocks = len / 128;
677 int start = 0;
678
679 NCR5380_write(hostdata->c400_ctl_status, CSR_BASE);
680 NCR5380_write(hostdata->c400_blk_cnt, blocks);
681 while (1) {
682 if (NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ) {
683 printk(KERN_ERR "53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
684 return -1;
685 }
686
687 if (NCR5380_read(hostdata->c400_blk_cnt) == 0)
688 break;
689 while (NCR5380_read(hostdata->c400_ctl_status) & CSR_HOST_BUF_NOT_RDY)
690 ; // FIXME - timeout
691#ifndef SCSI_G_NCR5380_MEM
692 if (hostdata->io_width == 2)
693 outsw(instance->io_port + hostdata->c400_host_buf,
694 src + start, 64);
695 else
696 outsb(instance->io_port + hostdata->c400_host_buf,
697 src + start, 128);
698#else
699 /* implies SCSI_G_NCR5380_MEM */
700 memcpy_toio(hostdata->iomem + NCR53C400_host_buffer,
701 src + start, 128);
702#endif
703 start += 128;
704 blocks--;
705 }
706 if (blocks) {
707 while (NCR5380_read(hostdata->c400_ctl_status) & CSR_HOST_BUF_NOT_RDY)
708 ; // FIXME - no timeout
709
710#ifndef SCSI_G_NCR5380_MEM
711 if (hostdata->io_width == 2)
712 outsw(instance->io_port + hostdata->c400_host_buf,
713 src + start, 64);
714 else
715 outsb(instance->io_port + hostdata->c400_host_buf,
716 src + start, 128);
717#else
718 /* implies SCSI_G_NCR5380_MEM */
719 memcpy_toio(hostdata->iomem + NCR53C400_host_buffer,
720 src + start, 128);
721#endif
722 start += 128;
723 blocks--;
724 }
725
726 /* wait for 53C80 registers to be available */
727 while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) {
728 udelay(4); /* DTC436 chip hangs without this */
729 /* FIXME - no timeout */
730 }
731
732 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) {
733 printk(KERN_ERR "53C400w: no end dma signal\n");
734 }
735
736 while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
737 ; // TIMEOUT
738 return 0;
739}
740
741static int generic_NCR5380_dma_xfer_len(struct scsi_cmnd *cmd)
742{
743 int transfersize = cmd->transfersize;
744
745 /* Limit transfers to 32K, for xx400 & xx406
746 * pseudoDMA that transfers in 128 bytes blocks.
747 */
748 if (transfersize > 32 * 1024 && cmd->SCp.this_residual &&
749 !(cmd->SCp.this_residual % transfersize))
750 transfersize = 32 * 1024;
751
752 /* 53C400 datasheet: non-modulo-128-byte transfers should use PIO */
753 if (transfersize % 128)
754 transfersize = 0;
755
756 return transfersize;
757}
758
759#endif /* PSEUDO_DMA */
760
761/*
762 * Include the NCR5380 core code that we build our driver around
763 */
764
765#include "NCR5380.c"
766
767static struct scsi_host_template driver_template = {
768 .proc_name = DRV_MODULE_NAME,
769 .name = "Generic NCR5380/NCR53C400 SCSI",
770 .detect = generic_NCR5380_detect,
771 .release = generic_NCR5380_release_resources,
772 .info = generic_NCR5380_info,
773 .queuecommand = generic_NCR5380_queue_command,
774 .eh_abort_handler = generic_NCR5380_abort,
775 .eh_bus_reset_handler = generic_NCR5380_bus_reset,
776 .bios_param = NCR5380_BIOSPARAM,
777 .can_queue = 16,
778 .this_id = 7,
779 .sg_tablesize = SG_ALL,
780 .cmd_per_lun = 2,
781 .use_clustering = DISABLE_CLUSTERING,
782 .cmd_size = NCR5380_CMD_SIZE,
783 .max_sectors = 128,
784};
785
786#include "scsi_module.c"
787
788module_param(ncr_irq, int, 0);
789module_param(ncr_dma, int, 0);
790module_param(ncr_addr, int, 0);
791module_param(ncr_5380, int, 0);
792module_param(ncr_53c400, int, 0);
793module_param(ncr_53c400a, int, 0);
794module_param(dtc_3181e, int, 0);
795module_param(hp_c2502, int, 0);
796MODULE_LICENSE("GPL");
797
798#if !defined(SCSI_G_NCR5380_MEM) && defined(MODULE)
799static struct isapnp_device_id id_table[] = {
800 {
801 ISAPNP_ANY_ID, ISAPNP_ANY_ID,
802 ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e),
803 0},
804 {0}
805};
806
807MODULE_DEVICE_TABLE(isapnp, id_table);
808#endif
809
810__setup("ncr5380=", do_NCR5380_setup);
811__setup("ncr53c400=", do_NCR53C400_setup);
812__setup("ncr53c400a=", do_NCR53C400A_setup);
813__setup("dtc3181e=", do_DTC3181E_setup);