Loading...
1/*
2 * Generic Generic NCR5380 driver
3 *
4 * Copyright 1993, Drew Eckhardt
5 * Visionary Computing
6 * (Unix and Linux consulting and custom programming)
7 * drew@colorado.edu
8 * +1 (303) 440-4894
9 *
10 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
11 * K.Lentin@cs.monash.edu.au
12 *
13 * NCR53C400A extensions (c) 1996, Ingmar Baumgart
14 * ingmar@gonzo.schwaben.de
15 *
16 * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg
17 * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl
18 *
19 * Added ISAPNP support for DTC436 adapters,
20 * Thomas Sailer, sailer@ife.ee.ethz.ch
21 *
22 * ALPHA RELEASE 1.
23 *
24 * For more information, please consult
25 *
26 * NCR 5380 Family
27 * SCSI Protocol Controller
28 * Databook
29 *
30 * NCR Microelectronics
31 * 1635 Aeroplaza Drive
32 * Colorado Springs, CO 80916
33 * 1+ (719) 578-3400
34 * 1+ (800) 334-5454
35 */
36
37/*
38 * TODO : flesh out DMA support, find some one actually using this (I have
39 * a memory mapped Trantor board that works fine)
40 */
41
42/*
43 * Options :
44 *
45 * PARITY - enable parity checking. Not supported.
46 *
47 * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
48 *
49 * USLEEP - enable support for devices that don't disconnect. Untested.
50 *
51 * The card is detected and initialized in one of several ways :
52 * 1. With command line overrides - NCR5380=port,irq may be
53 * used on the LILO command line to override the defaults.
54 *
55 * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is
56 * specified as an array of address, irq, dma, board tuples. Ie, for
57 * one board at 0x350, IRQ5, no dma, I could say
58 * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}
59 *
60 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an
61 * IRQ line if overridden on the command line.
62 *
63 * 3. When included as a module, with arguments passed on the command line:
64 * ncr_irq=xx the interrupt
65 * ncr_addr=xx the port or base address (for port or memory
66 * mapped, resp.)
67 * ncr_dma=xx the DMA
68 * ncr_5380=1 to set up for a NCR5380 board
69 * ncr_53c400=1 to set up for a NCR53C400 board
70 * e.g.
71 * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
72 * for a port mapped NCR5380 board or
73 * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
74 * for a memory mapped NCR53C400 board with interrupts disabled.
75 *
76 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an
77 * IRQ line if overridden on the command line.
78 *
79 */
80
81/*
82 * $Log: generic_NCR5380.c,v $
83 */
84
85/* settings for DTC3181E card with only Mustek scanner attached */
86#define USLEEP
87#define USLEEP_POLL 1
88#define USLEEP_SLEEP 20
89#define USLEEP_WAITLONG 500
90
91#define AUTOPROBE_IRQ
92#define AUTOSENSE
93
94
95#ifdef CONFIG_SCSI_GENERIC_NCR53C400
96#define NCR53C400_PSEUDO_DMA 1
97#define PSEUDO_DMA
98#define NCR53C400
99#define NCR5380_STATS
100#undef NCR5380_STAT_LIMIT
101#endif
102
103#include <asm/system.h>
104#include <asm/io.h>
105#include <linux/signal.h>
106#include <linux/blkdev.h>
107#include "scsi.h"
108#include <scsi/scsi_host.h>
109#include "g_NCR5380.h"
110#include "NCR5380.h"
111#include <linux/stat.h>
112#include <linux/init.h>
113#include <linux/ioport.h>
114#include <linux/isapnp.h>
115#include <linux/delay.h>
116#include <linux/interrupt.h>
117
118#define NCR_NOT_SET 0
119static int ncr_irq = NCR_NOT_SET;
120static int ncr_dma = NCR_NOT_SET;
121static int ncr_addr = NCR_NOT_SET;
122static int ncr_5380 = NCR_NOT_SET;
123static int ncr_53c400 = NCR_NOT_SET;
124static int ncr_53c400a = NCR_NOT_SET;
125static int dtc_3181e = NCR_NOT_SET;
126
127static struct override {
128 NCR5380_map_type NCR5380_map_name;
129 int irq;
130 int dma;
131 int board; /* Use NCR53c400, Ricoh, etc. extensions ? */
132} overrides
133#ifdef GENERIC_NCR5380_OVERRIDE
134[] __initdata = GENERIC_NCR5380_OVERRIDE;
135#else
136[1] __initdata = { { 0,},};
137#endif
138
139#define NO_OVERRIDES ARRAY_SIZE(overrides)
140
141#ifndef MODULE
142
143/**
144 * internal_setup - handle lilo command string override
145 * @board: BOARD_* identifier for the board
146 * @str: unused
147 * @ints: numeric parameters
148 *
149 * Do LILO command line initialization of the overrides array. Display
150 * errors when needed
151 *
152 * Locks: none
153 */
154
155static void __init internal_setup(int board, char *str, int *ints)
156{
157 static int commandline_current = 0;
158 switch (board) {
159 case BOARD_NCR5380:
160 if (ints[0] != 2 && ints[0] != 3) {
161 printk(KERN_ERR "generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");
162 return;
163 }
164 break;
165 case BOARD_NCR53C400:
166 if (ints[0] != 2) {
167 printk(KERN_ERR "generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");
168 return;
169 }
170 break;
171 case BOARD_NCR53C400A:
172 if (ints[0] != 2) {
173 printk(KERN_ERR "generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n");
174 return;
175 }
176 break;
177 case BOARD_DTC3181E:
178 if (ints[0] != 2) {
179 printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n");
180 return;
181 }
182 break;
183 }
184
185 if (commandline_current < NO_OVERRIDES) {
186 overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type) ints[1];
187 overrides[commandline_current].irq = ints[2];
188 if (ints[0] == 3)
189 overrides[commandline_current].dma = ints[3];
190 else
191 overrides[commandline_current].dma = DMA_NONE;
192 overrides[commandline_current].board = board;
193 ++commandline_current;
194 }
195}
196
197
198/**
199 * do_NCR53C80_setup - set up entry point
200 * @str: unused
201 *
202 * Setup function invoked at boot to parse the ncr5380= command
203 * line.
204 */
205
206static int __init do_NCR5380_setup(char *str)
207{
208 int ints[10];
209
210 get_options(str, ARRAY_SIZE(ints), ints);
211 internal_setup(BOARD_NCR5380, str, ints);
212 return 1;
213}
214
215/**
216 * do_NCR53C400_setup - set up entry point
217 * @str: unused
218 * @ints: integer parameters from kernel setup code
219 *
220 * Setup function invoked at boot to parse the ncr53c400= command
221 * line.
222 */
223
224static int __init do_NCR53C400_setup(char *str)
225{
226 int ints[10];
227
228 get_options(str, ARRAY_SIZE(ints), ints);
229 internal_setup(BOARD_NCR53C400, str, ints);
230 return 1;
231}
232
233/**
234 * do_NCR53C400A_setup - set up entry point
235 * @str: unused
236 * @ints: integer parameters from kernel setup code
237 *
238 * Setup function invoked at boot to parse the ncr53c400a= command
239 * line.
240 */
241
242static int __init do_NCR53C400A_setup(char *str)
243{
244 int ints[10];
245
246 get_options(str, ARRAY_SIZE(ints), ints);
247 internal_setup(BOARD_NCR53C400A, str, ints);
248 return 1;
249}
250
251/**
252 * do_DTC3181E_setup - set up entry point
253 * @str: unused
254 * @ints: integer parameters from kernel setup code
255 *
256 * Setup function invoked at boot to parse the dtc3181e= command
257 * line.
258 */
259
260static int __init do_DTC3181E_setup(char *str)
261{
262 int ints[10];
263
264 get_options(str, ARRAY_SIZE(ints), ints);
265 internal_setup(BOARD_DTC3181E, str, ints);
266 return 1;
267}
268
269#endif
270
271/**
272 * generic_NCR5380_detect - look for NCR5380 controllers
273 * @tpnt: the scsi template
274 *
275 * Scan for the present of NCR5380, NCR53C400, NCR53C400A, DTC3181E
276 * and DTC436(ISAPnP) controllers. If overrides have been set we use
277 * them.
278 *
279 * The caller supplied NCR5380_init function is invoked from here, before
280 * the interrupt line is taken.
281 *
282 * Locks: none
283 */
284
285int __init generic_NCR5380_detect(struct scsi_host_template * tpnt)
286{
287 static int current_override = 0;
288 int count;
289 unsigned int *ports;
290#ifndef SCSI_G_NCR5380_MEM
291 int i;
292 unsigned long region_size = 16;
293#endif
294 static unsigned int __initdata ncr_53c400a_ports[] = {
295 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
296 };
297 static unsigned int __initdata dtc_3181e_ports[] = {
298 0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0
299 };
300 int flags = 0;
301 struct Scsi_Host *instance;
302#ifdef SCSI_G_NCR5380_MEM
303 unsigned long base;
304 void __iomem *iomem;
305#endif
306
307 if (ncr_irq != NCR_NOT_SET)
308 overrides[0].irq = ncr_irq;
309 if (ncr_dma != NCR_NOT_SET)
310 overrides[0].dma = ncr_dma;
311 if (ncr_addr != NCR_NOT_SET)
312 overrides[0].NCR5380_map_name = (NCR5380_map_type) ncr_addr;
313 if (ncr_5380 != NCR_NOT_SET)
314 overrides[0].board = BOARD_NCR5380;
315 else if (ncr_53c400 != NCR_NOT_SET)
316 overrides[0].board = BOARD_NCR53C400;
317 else if (ncr_53c400a != NCR_NOT_SET)
318 overrides[0].board = BOARD_NCR53C400A;
319 else if (dtc_3181e != NCR_NOT_SET)
320 overrides[0].board = BOARD_DTC3181E;
321#ifndef SCSI_G_NCR5380_MEM
322 if (!current_override && isapnp_present()) {
323 struct pnp_dev *dev = NULL;
324 count = 0;
325 while ((dev = pnp_find_dev(NULL, ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e), dev))) {
326 if (count >= NO_OVERRIDES)
327 break;
328 if (pnp_device_attach(dev) < 0)
329 continue;
330 if (pnp_activate_dev(dev) < 0) {
331 printk(KERN_ERR "dtc436e probe: activate failed\n");
332 pnp_device_detach(dev);
333 continue;
334 }
335 if (!pnp_port_valid(dev, 0)) {
336 printk(KERN_ERR "dtc436e probe: no valid port\n");
337 pnp_device_detach(dev);
338 continue;
339 }
340 if (pnp_irq_valid(dev, 0))
341 overrides[count].irq = pnp_irq(dev, 0);
342 else
343 overrides[count].irq = SCSI_IRQ_NONE;
344 if (pnp_dma_valid(dev, 0))
345 overrides[count].dma = pnp_dma(dev, 0);
346 else
347 overrides[count].dma = DMA_NONE;
348 overrides[count].NCR5380_map_name = (NCR5380_map_type) pnp_port_start(dev, 0);
349 overrides[count].board = BOARD_DTC3181E;
350 count++;
351 }
352 }
353#endif
354 tpnt->proc_name = "g_NCR5380";
355
356 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
357 if (!(overrides[current_override].NCR5380_map_name))
358 continue;
359
360 ports = NULL;
361 switch (overrides[current_override].board) {
362 case BOARD_NCR5380:
363 flags = FLAG_NO_PSEUDO_DMA;
364 break;
365 case BOARD_NCR53C400:
366 flags = FLAG_NCR53C400;
367 break;
368 case BOARD_NCR53C400A:
369 flags = FLAG_NO_PSEUDO_DMA;
370 ports = ncr_53c400a_ports;
371 break;
372 case BOARD_DTC3181E:
373 flags = FLAG_NO_PSEUDO_DMA | FLAG_DTC3181E;
374 ports = dtc_3181e_ports;
375 break;
376 }
377
378#ifndef SCSI_G_NCR5380_MEM
379 if (ports) {
380 /* wakeup sequence for the NCR53C400A and DTC3181E */
381
382 /* Disable the adapter and look for a free io port */
383 outb(0x59, 0x779);
384 outb(0xb9, 0x379);
385 outb(0xc5, 0x379);
386 outb(0xae, 0x379);
387 outb(0xa6, 0x379);
388 outb(0x00, 0x379);
389
390 if (overrides[current_override].NCR5380_map_name != PORT_AUTO)
391 for (i = 0; ports[i]; i++) {
392 if (!request_region(ports[i], 16, "ncr53c80"))
393 continue;
394 if (overrides[current_override].NCR5380_map_name == ports[i])
395 break;
396 release_region(ports[i], 16);
397 } else
398 for (i = 0; ports[i]; i++) {
399 if (!request_region(ports[i], 16, "ncr53c80"))
400 continue;
401 if (inb(ports[i]) == 0xff)
402 break;
403 release_region(ports[i], 16);
404 }
405 if (ports[i]) {
406 /* At this point we have our region reserved */
407 outb(0x59, 0x779);
408 outb(0xb9, 0x379);
409 outb(0xc5, 0x379);
410 outb(0xae, 0x379);
411 outb(0xa6, 0x379);
412 outb(0x80 | i, 0x379); /* set io port to be used */
413 outb(0xc0, ports[i] + 9);
414 if (inb(ports[i] + 9) != 0x80)
415 continue;
416 else
417 overrides[current_override].NCR5380_map_name = ports[i];
418 } else
419 continue;
420 }
421 else
422 {
423 /* Not a 53C400A style setup - just grab */
424 if(!(request_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380")))
425 continue;
426 region_size = NCR5380_region_size;
427 }
428#else
429 base = overrides[current_override].NCR5380_map_name;
430 if (!request_mem_region(base, NCR5380_region_size, "ncr5380"))
431 continue;
432 iomem = ioremap(base, NCR5380_region_size);
433 if (!iomem) {
434 release_mem_region(base, NCR5380_region_size);
435 continue;
436 }
437#endif
438 instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
439 if (instance == NULL) {
440#ifndef SCSI_G_NCR5380_MEM
441 release_region(overrides[current_override].NCR5380_map_name, region_size);
442#else
443 iounmap(iomem);
444 release_mem_region(base, NCR5380_region_size);
445#endif
446 continue;
447 }
448
449 instance->NCR5380_instance_name = overrides[current_override].NCR5380_map_name;
450#ifndef SCSI_G_NCR5380_MEM
451 instance->n_io_port = region_size;
452#else
453 ((struct NCR5380_hostdata *)instance->hostdata)->iomem = iomem;
454#endif
455
456 NCR5380_init(instance, flags);
457
458 if (overrides[current_override].irq != IRQ_AUTO)
459 instance->irq = overrides[current_override].irq;
460 else
461 instance->irq = NCR5380_probe_irq(instance, 0xffff);
462
463 if (instance->irq != SCSI_IRQ_NONE)
464 if (request_irq(instance->irq, generic_NCR5380_intr,
465 IRQF_DISABLED, "NCR5380", instance)) {
466 printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
467 instance->irq = SCSI_IRQ_NONE;
468 }
469
470 if (instance->irq == SCSI_IRQ_NONE) {
471 printk(KERN_INFO "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
472 printk(KERN_INFO "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
473 }
474
475 printk(KERN_INFO "scsi%d : at " STRVAL(NCR5380_map_name) " 0x%x", instance->host_no, (unsigned int) instance->NCR5380_instance_name);
476 if (instance->irq == SCSI_IRQ_NONE)
477 printk(" interrupts disabled");
478 else
479 printk(" irq %d", instance->irq);
480 printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, GENERIC_NCR5380_PUBLIC_RELEASE);
481 NCR5380_print_options(instance);
482 printk("\n");
483
484 ++current_override;
485 ++count;
486 }
487 return count;
488}
489
490/**
491 * generic_NCR5380_info - reporting string
492 * @host: NCR5380 to report on
493 *
494 * Report driver information for the NCR5380
495 */
496
497const char *generic_NCR5380_info(struct Scsi_Host *host)
498{
499 static const char string[] = "Generic NCR5380/53C400 Driver";
500 return string;
501}
502
503/**
504 * generic_NCR5380_release_resources - free resources
505 * @instance: host adapter to clean up
506 *
507 * Free the generic interface resources from this adapter.
508 *
509 * Locks: none
510 */
511
512int generic_NCR5380_release_resources(struct Scsi_Host *instance)
513{
514 NCR5380_local_declare();
515 NCR5380_setup(instance);
516
517 if (instance->irq != SCSI_IRQ_NONE)
518 free_irq(instance->irq, instance);
519 NCR5380_exit(instance);
520
521#ifndef SCSI_G_NCR5380_MEM
522 release_region(instance->NCR5380_instance_name, instance->n_io_port);
523#else
524 iounmap(((struct NCR5380_hostdata *)instance->hostdata)->iomem);
525 release_mem_region(instance->NCR5380_instance_name, NCR5380_region_size);
526#endif
527
528
529 return 0;
530}
531
532#ifdef BIOSPARAM
533/**
534 * generic_NCR5380_biosparam
535 * @disk: disk to compute geometry for
536 * @dev: device identifier for this disk
537 * @ip: sizes to fill in
538 *
539 * Generates a BIOS / DOS compatible H-C-S mapping for the specified
540 * device / size.
541 *
542 * XXX Most SCSI boards use this mapping, I could be incorrect. Someone
543 * using hard disks on a trantor should verify that this mapping
544 * corresponds to that used by the BIOS / ASPI driver by running the linux
545 * fdisk program and matching the H_C_S coordinates to what DOS uses.
546 *
547 * Locks: none
548 */
549
550static int
551generic_NCR5380_biosparam(struct scsi_device *sdev, struct block_device *bdev,
552 sector_t capacity, int *ip)
553{
554 ip[0] = 64;
555 ip[1] = 32;
556 ip[2] = capacity >> 11;
557 return 0;
558}
559#endif
560
561#ifdef NCR53C400_PSEUDO_DMA
562
563/**
564 * NCR5380_pread - pseudo DMA read
565 * @instance: adapter to read from
566 * @dst: buffer to read into
567 * @len: buffer length
568 *
569 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
570 * controller
571 */
572
573static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
574{
575 int blocks = len / 128;
576 int start = 0;
577 int bl;
578
579 NCR5380_local_declare();
580 NCR5380_setup(instance);
581
582 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE | CSR_TRANS_DIR);
583 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
584 while (1) {
585 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
586 break;
587 }
588 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
589 printk(KERN_ERR "53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
590 return -1;
591 }
592 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY);
593
594#ifndef SCSI_G_NCR5380_MEM
595 {
596 int i;
597 for (i = 0; i < 128; i++)
598 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
599 }
600#else
601 /* implies SCSI_G_NCR5380_MEM */
602 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
603#endif
604 start += 128;
605 blocks--;
606 }
607
608 if (blocks) {
609 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
610 {
611 // FIXME - no timeout
612 }
613
614#ifndef SCSI_G_NCR5380_MEM
615 {
616 int i;
617 for (i = 0; i < 128; i++)
618 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
619 }
620#else
621 /* implies SCSI_G_NCR5380_MEM */
622 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
623#endif
624 start += 128;
625 blocks--;
626 }
627
628 if (!(NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
629 printk("53C400r: no 53C80 gated irq after transfer");
630
631#if 0
632 /*
633 * DON'T DO THIS - THEY NEVER ARRIVE!
634 */
635 printk("53C400r: Waiting for 53C80 registers\n");
636 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG)
637 ;
638#endif
639 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
640 printk(KERN_ERR "53C400r: no end dma signal\n");
641
642 NCR5380_write(MODE_REG, MR_BASE);
643 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
644 return 0;
645}
646
647/**
648 * NCR5380_write - pseudo DMA write
649 * @instance: adapter to read from
650 * @dst: buffer to read into
651 * @len: buffer length
652 *
653 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
654 * controller
655 */
656
657static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
658{
659 int blocks = len / 128;
660 int start = 0;
661 int bl;
662 int i;
663
664 NCR5380_local_declare();
665 NCR5380_setup(instance);
666
667 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);
668 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
669 while (1) {
670 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
671 printk(KERN_ERR "53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
672 return -1;
673 }
674
675 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
676 break;
677 }
678 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
679 ; // FIXME - timeout
680#ifndef SCSI_G_NCR5380_MEM
681 {
682 for (i = 0; i < 128; i++)
683 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
684 }
685#else
686 /* implies SCSI_G_NCR5380_MEM */
687 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
688#endif
689 start += 128;
690 blocks--;
691 }
692 if (blocks) {
693 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
694 ; // FIXME - no timeout
695
696#ifndef SCSI_G_NCR5380_MEM
697 {
698 for (i = 0; i < 128; i++)
699 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
700 }
701#else
702 /* implies SCSI_G_NCR5380_MEM */
703 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
704#endif
705 start += 128;
706 blocks--;
707 }
708
709#if 0
710 printk("53C400w: waiting for registers to be available\n");
711 THEY NEVER DO ! while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG);
712 printk("53C400w: Got em\n");
713#endif
714
715 /* Let's wait for this instead - could be ugly */
716 /* All documentation says to check for this. Maybe my hardware is too
717 * fast. Waiting for it seems to work fine! KLL
718 */
719 while (!(i = NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
720 ; // FIXME - no timeout
721
722 /*
723 * I know. i is certainly != 0 here but the loop is new. See previous
724 * comment.
725 */
726 if (i) {
727 if (!((i = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER))
728 printk(KERN_ERR "53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i);
729 } else
730 printk(KERN_ERR "53C400w: no 53C80 gated irq after transfer (last block)\n");
731
732#if 0
733 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) {
734 printk(KERN_ERR "53C400w: no end dma signal\n");
735 }
736#endif
737 while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
738 ; // TIMEOUT
739 return 0;
740}
741#endif /* PSEUDO_DMA */
742
743/*
744 * Include the NCR5380 core code that we build our driver around
745 */
746
747#include "NCR5380.c"
748
749#define PRINTP(x) len += sprintf(buffer+len, x)
750#define ANDP ,
751
752static int sprint_opcode(char *buffer, int len, int opcode)
753{
754 int start = len;
755 PRINTP("0x%02x " ANDP opcode);
756 return len - start;
757}
758
759static int sprint_command(char *buffer, int len, unsigned char *command)
760{
761 int i, s, start = len;
762 len += sprint_opcode(buffer, len, command[0]);
763 for (i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i)
764 PRINTP("%02x " ANDP command[i]);
765 PRINTP("\n");
766 return len - start;
767}
768
769/**
770 * sprintf_Scsi_Cmnd - print a scsi command
771 * @buffer: buffr to print into
772 * @len: buffer length
773 * @cmd: SCSI command block
774 *
775 * Print out the target and command data in hex
776 */
777
778static int sprint_Scsi_Cmnd(char *buffer, int len, Scsi_Cmnd * cmd)
779{
780 int start = len;
781 PRINTP("host number %d destination target %d, lun %d\n" ANDP cmd->device->host->host_no ANDP cmd->device->id ANDP cmd->device->lun);
782 PRINTP(" command = ");
783 len += sprint_command(buffer, len, cmd->cmnd);
784 return len - start;
785}
786
787/**
788 * generic_NCR5380_proc_info - /proc for NCR5380 driver
789 * @buffer: buffer to print into
790 * @start: start position
791 * @offset: offset into buffer
792 * @len: length
793 * @hostno: instance to affect
794 * @inout: read/write
795 *
796 * Provide the procfs information for the 5380 controller. We fill
797 * this with useful debugging information including the commands
798 * being executed, disconnected command queue and the statistical
799 * data
800 *
801 * Locks: global cli/lock for queue walk
802 */
803
804static int generic_NCR5380_proc_info(struct Scsi_Host *scsi_ptr, char *buffer, char **start, off_t offset, int length, int inout)
805{
806 int len = 0;
807 NCR5380_local_declare();
808 unsigned long flags;
809 unsigned char status;
810 int i;
811 Scsi_Cmnd *ptr;
812 struct NCR5380_hostdata *hostdata;
813#ifdef NCR5380_STATS
814 struct scsi_device *dev;
815#endif
816
817 NCR5380_setup(scsi_ptr);
818 hostdata = (struct NCR5380_hostdata *) scsi_ptr->hostdata;
819
820 spin_lock_irqsave(scsi_ptr->host_lock, flags);
821 PRINTP("SCSI host number %d : %s\n" ANDP scsi_ptr->host_no ANDP scsi_ptr->hostt->name);
822 PRINTP("Generic NCR5380 driver version %d\n" ANDP GENERIC_NCR5380_PUBLIC_RELEASE);
823 PRINTP("NCR5380 core version %d\n" ANDP NCR5380_PUBLIC_RELEASE);
824#ifdef NCR53C400
825 PRINTP("NCR53C400 extension version %d\n" ANDP NCR53C400_PUBLIC_RELEASE);
826 PRINTP("NCR53C400 card%s detected\n" ANDP(((struct NCR5380_hostdata *) scsi_ptr->hostdata)->flags & FLAG_NCR53C400) ? "" : " not");
827# if NCR53C400_PSEUDO_DMA
828 PRINTP("NCR53C400 pseudo DMA used\n");
829# endif
830#else
831 PRINTP("NO NCR53C400 driver extensions\n");
832#endif
833 PRINTP("Using %s mapping at %s 0x%lx, " ANDP STRVAL(NCR5380_map_config) ANDP STRVAL(NCR5380_map_name) ANDP scsi_ptr->NCR5380_instance_name);
834 if (scsi_ptr->irq == SCSI_IRQ_NONE)
835 PRINTP("no interrupt\n");
836 else
837 PRINTP("on interrupt %d\n" ANDP scsi_ptr->irq);
838
839#ifdef NCR5380_STATS
840 if (hostdata->connected || hostdata->issue_queue || hostdata->disconnected_queue)
841 PRINTP("There are commands pending, transfer rates may be crud\n");
842 if (hostdata->pendingr)
843 PRINTP(" %d pending reads" ANDP hostdata->pendingr);
844 if (hostdata->pendingw)
845 PRINTP(" %d pending writes" ANDP hostdata->pendingw);
846 if (hostdata->pendingr || hostdata->pendingw)
847 PRINTP("\n");
848 shost_for_each_device(dev, scsi_ptr) {
849 unsigned long br = hostdata->bytes_read[dev->id];
850 unsigned long bw = hostdata->bytes_write[dev->id];
851 long tr = hostdata->time_read[dev->id] / HZ;
852 long tw = hostdata->time_write[dev->id] / HZ;
853
854 PRINTP(" T:%d %s " ANDP dev->id ANDP scsi_device_type(dev->type));
855 for (i = 0; i < 8; i++)
856 if (dev->vendor[i] >= 0x20)
857 *(buffer + (len++)) = dev->vendor[i];
858 *(buffer + (len++)) = ' ';
859 for (i = 0; i < 16; i++)
860 if (dev->model[i] >= 0x20)
861 *(buffer + (len++)) = dev->model[i];
862 *(buffer + (len++)) = ' ';
863 for (i = 0; i < 4; i++)
864 if (dev->rev[i] >= 0x20)
865 *(buffer + (len++)) = dev->rev[i];
866 *(buffer + (len++)) = ' ';
867
868 PRINTP("\n%10ld kb read in %5ld secs" ANDP br / 1024 ANDP tr);
869 if (tr)
870 PRINTP(" @ %5ld bps" ANDP br / tr);
871
872 PRINTP("\n%10ld kb written in %5ld secs" ANDP bw / 1024 ANDP tw);
873 if (tw)
874 PRINTP(" @ %5ld bps" ANDP bw / tw);
875 PRINTP("\n");
876 }
877#endif
878
879 status = NCR5380_read(STATUS_REG);
880 if (!(status & SR_REQ))
881 PRINTP("REQ not asserted, phase unknown.\n");
882 else {
883 for (i = 0; (phases[i].value != PHASE_UNKNOWN) && (phases[i].value != (status & PHASE_MASK)); ++i);
884 PRINTP("Phase %s\n" ANDP phases[i].name);
885 }
886
887 if (!hostdata->connected) {
888 PRINTP("No currently connected command\n");
889 } else {
890 len += sprint_Scsi_Cmnd(buffer, len, (Scsi_Cmnd *) hostdata->connected);
891 }
892
893 PRINTP("issue_queue\n");
894
895 for (ptr = (Scsi_Cmnd *) hostdata->issue_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
896 len += sprint_Scsi_Cmnd(buffer, len, ptr);
897
898 PRINTP("disconnected_queue\n");
899
900 for (ptr = (Scsi_Cmnd *) hostdata->disconnected_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
901 len += sprint_Scsi_Cmnd(buffer, len, ptr);
902
903 *start = buffer + offset;
904 len -= offset;
905 if (len > length)
906 len = length;
907 spin_unlock_irqrestore(scsi_ptr->host_lock, flags);
908 return len;
909}
910
911#undef PRINTP
912#undef ANDP
913
914static struct scsi_host_template driver_template = {
915 .proc_info = generic_NCR5380_proc_info,
916 .name = "Generic NCR5380/NCR53C400 Scsi Driver",
917 .detect = generic_NCR5380_detect,
918 .release = generic_NCR5380_release_resources,
919 .info = generic_NCR5380_info,
920 .queuecommand = generic_NCR5380_queue_command,
921 .eh_abort_handler = generic_NCR5380_abort,
922 .eh_bus_reset_handler = generic_NCR5380_bus_reset,
923 .bios_param = NCR5380_BIOSPARAM,
924 .can_queue = CAN_QUEUE,
925 .this_id = 7,
926 .sg_tablesize = SG_ALL,
927 .cmd_per_lun = CMD_PER_LUN,
928 .use_clustering = DISABLE_CLUSTERING,
929};
930#include <linux/module.h>
931#include "scsi_module.c"
932
933module_param(ncr_irq, int, 0);
934module_param(ncr_dma, int, 0);
935module_param(ncr_addr, int, 0);
936module_param(ncr_5380, int, 0);
937module_param(ncr_53c400, int, 0);
938module_param(ncr_53c400a, int, 0);
939module_param(dtc_3181e, int, 0);
940MODULE_LICENSE("GPL");
941
942#ifndef SCSI_G_NCR5380_MEM
943static struct isapnp_device_id id_table[] __devinitdata = {
944 {
945 ISAPNP_ANY_ID, ISAPNP_ANY_ID,
946 ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e),
947 0},
948 {0}
949};
950
951MODULE_DEVICE_TABLE(isapnp, id_table);
952#endif
953
954__setup("ncr5380=", do_NCR5380_setup);
955__setup("ncr53c400=", do_NCR53C400_setup);
956__setup("ncr53c400a=", do_NCR53C400A_setup);
957__setup("dtc3181e=", do_DTC3181E_setup);
1/*
2 * Generic Generic NCR5380 driver
3 *
4 * Copyright 1993, Drew Eckhardt
5 * Visionary Computing
6 * (Unix and Linux consulting and custom programming)
7 * drew@colorado.edu
8 * +1 (303) 440-4894
9 *
10 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
11 * K.Lentin@cs.monash.edu.au
12 *
13 * NCR53C400A extensions (c) 1996, Ingmar Baumgart
14 * ingmar@gonzo.schwaben.de
15 *
16 * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg
17 * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl
18 *
19 * Added ISAPNP support for DTC436 adapters,
20 * Thomas Sailer, sailer@ife.ee.ethz.ch
21 *
22 * ALPHA RELEASE 1.
23 *
24 * For more information, please consult
25 *
26 * NCR 5380 Family
27 * SCSI Protocol Controller
28 * Databook
29 *
30 * NCR Microelectronics
31 * 1635 Aeroplaza Drive
32 * Colorado Springs, CO 80916
33 * 1+ (719) 578-3400
34 * 1+ (800) 334-5454
35 */
36
37/*
38 * TODO : flesh out DMA support, find some one actually using this (I have
39 * a memory mapped Trantor board that works fine)
40 */
41
42/*
43 * Options :
44 *
45 * PARITY - enable parity checking. Not supported.
46 *
47 * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
48 *
49 * USLEEP - enable support for devices that don't disconnect. Untested.
50 *
51 * The card is detected and initialized in one of several ways :
52 * 1. With command line overrides - NCR5380=port,irq may be
53 * used on the LILO command line to override the defaults.
54 *
55 * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is
56 * specified as an array of address, irq, dma, board tuples. Ie, for
57 * one board at 0x350, IRQ5, no dma, I could say
58 * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}
59 *
60 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an
61 * IRQ line if overridden on the command line.
62 *
63 * 3. When included as a module, with arguments passed on the command line:
64 * ncr_irq=xx the interrupt
65 * ncr_addr=xx the port or base address (for port or memory
66 * mapped, resp.)
67 * ncr_dma=xx the DMA
68 * ncr_5380=1 to set up for a NCR5380 board
69 * ncr_53c400=1 to set up for a NCR53C400 board
70 * e.g.
71 * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
72 * for a port mapped NCR5380 board or
73 * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
74 * for a memory mapped NCR53C400 board with interrupts disabled.
75 *
76 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an
77 * IRQ line if overridden on the command line.
78 *
79 */
80
81/*
82 * $Log: generic_NCR5380.c,v $
83 */
84
85/* settings for DTC3181E card with only Mustek scanner attached */
86#define USLEEP
87#define USLEEP_POLL 1
88#define USLEEP_SLEEP 20
89#define USLEEP_WAITLONG 500
90
91#define AUTOPROBE_IRQ
92#define AUTOSENSE
93
94
95#ifdef CONFIG_SCSI_GENERIC_NCR53C400
96#define NCR53C400_PSEUDO_DMA 1
97#define PSEUDO_DMA
98#define NCR53C400
99#define NCR5380_STATS
100#undef NCR5380_STAT_LIMIT
101#endif
102
103#include <asm/io.h>
104#include <linux/signal.h>
105#include <linux/blkdev.h>
106#include "scsi.h"
107#include <scsi/scsi_host.h>
108#include "g_NCR5380.h"
109#include "NCR5380.h"
110#include <linux/stat.h>
111#include <linux/init.h>
112#include <linux/ioport.h>
113#include <linux/isapnp.h>
114#include <linux/delay.h>
115#include <linux/interrupt.h>
116
117#define NCR_NOT_SET 0
118static int ncr_irq = NCR_NOT_SET;
119static int ncr_dma = NCR_NOT_SET;
120static int ncr_addr = NCR_NOT_SET;
121static int ncr_5380 = NCR_NOT_SET;
122static int ncr_53c400 = NCR_NOT_SET;
123static int ncr_53c400a = NCR_NOT_SET;
124static int dtc_3181e = NCR_NOT_SET;
125
126static struct override {
127 NCR5380_map_type NCR5380_map_name;
128 int irq;
129 int dma;
130 int board; /* Use NCR53c400, Ricoh, etc. extensions ? */
131} overrides
132#ifdef GENERIC_NCR5380_OVERRIDE
133[] __initdata = GENERIC_NCR5380_OVERRIDE;
134#else
135[1] __initdata = { { 0,},};
136#endif
137
138#define NO_OVERRIDES ARRAY_SIZE(overrides)
139
140#ifndef MODULE
141
142/**
143 * internal_setup - handle lilo command string override
144 * @board: BOARD_* identifier for the board
145 * @str: unused
146 * @ints: numeric parameters
147 *
148 * Do LILO command line initialization of the overrides array. Display
149 * errors when needed
150 *
151 * Locks: none
152 */
153
154static void __init internal_setup(int board, char *str, int *ints)
155{
156 static int commandline_current = 0;
157 switch (board) {
158 case BOARD_NCR5380:
159 if (ints[0] != 2 && ints[0] != 3) {
160 printk(KERN_ERR "generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");
161 return;
162 }
163 break;
164 case BOARD_NCR53C400:
165 if (ints[0] != 2) {
166 printk(KERN_ERR "generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");
167 return;
168 }
169 break;
170 case BOARD_NCR53C400A:
171 if (ints[0] != 2) {
172 printk(KERN_ERR "generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n");
173 return;
174 }
175 break;
176 case BOARD_DTC3181E:
177 if (ints[0] != 2) {
178 printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n");
179 return;
180 }
181 break;
182 }
183
184 if (commandline_current < NO_OVERRIDES) {
185 overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type) ints[1];
186 overrides[commandline_current].irq = ints[2];
187 if (ints[0] == 3)
188 overrides[commandline_current].dma = ints[3];
189 else
190 overrides[commandline_current].dma = DMA_NONE;
191 overrides[commandline_current].board = board;
192 ++commandline_current;
193 }
194}
195
196
197/**
198 * do_NCR53C80_setup - set up entry point
199 * @str: unused
200 *
201 * Setup function invoked at boot to parse the ncr5380= command
202 * line.
203 */
204
205static int __init do_NCR5380_setup(char *str)
206{
207 int ints[10];
208
209 get_options(str, ARRAY_SIZE(ints), ints);
210 internal_setup(BOARD_NCR5380, str, ints);
211 return 1;
212}
213
214/**
215 * do_NCR53C400_setup - set up entry point
216 * @str: unused
217 * @ints: integer parameters from kernel setup code
218 *
219 * Setup function invoked at boot to parse the ncr53c400= command
220 * line.
221 */
222
223static int __init do_NCR53C400_setup(char *str)
224{
225 int ints[10];
226
227 get_options(str, ARRAY_SIZE(ints), ints);
228 internal_setup(BOARD_NCR53C400, str, ints);
229 return 1;
230}
231
232/**
233 * do_NCR53C400A_setup - set up entry point
234 * @str: unused
235 * @ints: integer parameters from kernel setup code
236 *
237 * Setup function invoked at boot to parse the ncr53c400a= command
238 * line.
239 */
240
241static int __init do_NCR53C400A_setup(char *str)
242{
243 int ints[10];
244
245 get_options(str, ARRAY_SIZE(ints), ints);
246 internal_setup(BOARD_NCR53C400A, str, ints);
247 return 1;
248}
249
250/**
251 * do_DTC3181E_setup - set up entry point
252 * @str: unused
253 * @ints: integer parameters from kernel setup code
254 *
255 * Setup function invoked at boot to parse the dtc3181e= command
256 * line.
257 */
258
259static int __init do_DTC3181E_setup(char *str)
260{
261 int ints[10];
262
263 get_options(str, ARRAY_SIZE(ints), ints);
264 internal_setup(BOARD_DTC3181E, str, ints);
265 return 1;
266}
267
268#endif
269
270/**
271 * generic_NCR5380_detect - look for NCR5380 controllers
272 * @tpnt: the scsi template
273 *
274 * Scan for the present of NCR5380, NCR53C400, NCR53C400A, DTC3181E
275 * and DTC436(ISAPnP) controllers. If overrides have been set we use
276 * them.
277 *
278 * The caller supplied NCR5380_init function is invoked from here, before
279 * the interrupt line is taken.
280 *
281 * Locks: none
282 */
283
284int __init generic_NCR5380_detect(struct scsi_host_template * tpnt)
285{
286 static int current_override = 0;
287 int count;
288 unsigned int *ports;
289#ifndef SCSI_G_NCR5380_MEM
290 int i;
291 unsigned long region_size = 16;
292#endif
293 static unsigned int __initdata ncr_53c400a_ports[] = {
294 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
295 };
296 static unsigned int __initdata dtc_3181e_ports[] = {
297 0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0
298 };
299 int flags = 0;
300 struct Scsi_Host *instance;
301#ifdef SCSI_G_NCR5380_MEM
302 unsigned long base;
303 void __iomem *iomem;
304#endif
305
306 if (ncr_irq != NCR_NOT_SET)
307 overrides[0].irq = ncr_irq;
308 if (ncr_dma != NCR_NOT_SET)
309 overrides[0].dma = ncr_dma;
310 if (ncr_addr != NCR_NOT_SET)
311 overrides[0].NCR5380_map_name = (NCR5380_map_type) ncr_addr;
312 if (ncr_5380 != NCR_NOT_SET)
313 overrides[0].board = BOARD_NCR5380;
314 else if (ncr_53c400 != NCR_NOT_SET)
315 overrides[0].board = BOARD_NCR53C400;
316 else if (ncr_53c400a != NCR_NOT_SET)
317 overrides[0].board = BOARD_NCR53C400A;
318 else if (dtc_3181e != NCR_NOT_SET)
319 overrides[0].board = BOARD_DTC3181E;
320#ifndef SCSI_G_NCR5380_MEM
321 if (!current_override && isapnp_present()) {
322 struct pnp_dev *dev = NULL;
323 count = 0;
324 while ((dev = pnp_find_dev(NULL, ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e), dev))) {
325 if (count >= NO_OVERRIDES)
326 break;
327 if (pnp_device_attach(dev) < 0)
328 continue;
329 if (pnp_activate_dev(dev) < 0) {
330 printk(KERN_ERR "dtc436e probe: activate failed\n");
331 pnp_device_detach(dev);
332 continue;
333 }
334 if (!pnp_port_valid(dev, 0)) {
335 printk(KERN_ERR "dtc436e probe: no valid port\n");
336 pnp_device_detach(dev);
337 continue;
338 }
339 if (pnp_irq_valid(dev, 0))
340 overrides[count].irq = pnp_irq(dev, 0);
341 else
342 overrides[count].irq = SCSI_IRQ_NONE;
343 if (pnp_dma_valid(dev, 0))
344 overrides[count].dma = pnp_dma(dev, 0);
345 else
346 overrides[count].dma = DMA_NONE;
347 overrides[count].NCR5380_map_name = (NCR5380_map_type) pnp_port_start(dev, 0);
348 overrides[count].board = BOARD_DTC3181E;
349 count++;
350 }
351 }
352#endif
353 tpnt->proc_name = "g_NCR5380";
354
355 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
356 if (!(overrides[current_override].NCR5380_map_name))
357 continue;
358
359 ports = NULL;
360 switch (overrides[current_override].board) {
361 case BOARD_NCR5380:
362 flags = FLAG_NO_PSEUDO_DMA;
363 break;
364 case BOARD_NCR53C400:
365 flags = FLAG_NCR53C400;
366 break;
367 case BOARD_NCR53C400A:
368 flags = FLAG_NO_PSEUDO_DMA;
369 ports = ncr_53c400a_ports;
370 break;
371 case BOARD_DTC3181E:
372 flags = FLAG_NO_PSEUDO_DMA | FLAG_DTC3181E;
373 ports = dtc_3181e_ports;
374 break;
375 }
376
377#ifndef SCSI_G_NCR5380_MEM
378 if (ports) {
379 /* wakeup sequence for the NCR53C400A and DTC3181E */
380
381 /* Disable the adapter and look for a free io port */
382 outb(0x59, 0x779);
383 outb(0xb9, 0x379);
384 outb(0xc5, 0x379);
385 outb(0xae, 0x379);
386 outb(0xa6, 0x379);
387 outb(0x00, 0x379);
388
389 if (overrides[current_override].NCR5380_map_name != PORT_AUTO)
390 for (i = 0; ports[i]; i++) {
391 if (!request_region(ports[i], 16, "ncr53c80"))
392 continue;
393 if (overrides[current_override].NCR5380_map_name == ports[i])
394 break;
395 release_region(ports[i], 16);
396 } else
397 for (i = 0; ports[i]; i++) {
398 if (!request_region(ports[i], 16, "ncr53c80"))
399 continue;
400 if (inb(ports[i]) == 0xff)
401 break;
402 release_region(ports[i], 16);
403 }
404 if (ports[i]) {
405 /* At this point we have our region reserved */
406 outb(0x59, 0x779);
407 outb(0xb9, 0x379);
408 outb(0xc5, 0x379);
409 outb(0xae, 0x379);
410 outb(0xa6, 0x379);
411 outb(0x80 | i, 0x379); /* set io port to be used */
412 outb(0xc0, ports[i] + 9);
413 if (inb(ports[i] + 9) != 0x80)
414 continue;
415 else
416 overrides[current_override].NCR5380_map_name = ports[i];
417 } else
418 continue;
419 }
420 else
421 {
422 /* Not a 53C400A style setup - just grab */
423 if(!(request_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380")))
424 continue;
425 region_size = NCR5380_region_size;
426 }
427#else
428 base = overrides[current_override].NCR5380_map_name;
429 if (!request_mem_region(base, NCR5380_region_size, "ncr5380"))
430 continue;
431 iomem = ioremap(base, NCR5380_region_size);
432 if (!iomem) {
433 release_mem_region(base, NCR5380_region_size);
434 continue;
435 }
436#endif
437 instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
438 if (instance == NULL) {
439#ifndef SCSI_G_NCR5380_MEM
440 release_region(overrides[current_override].NCR5380_map_name, region_size);
441#else
442 iounmap(iomem);
443 release_mem_region(base, NCR5380_region_size);
444#endif
445 continue;
446 }
447
448 instance->NCR5380_instance_name = overrides[current_override].NCR5380_map_name;
449#ifndef SCSI_G_NCR5380_MEM
450 instance->n_io_port = region_size;
451#else
452 ((struct NCR5380_hostdata *)instance->hostdata)->iomem = iomem;
453#endif
454
455 NCR5380_init(instance, flags);
456
457 if (overrides[current_override].irq != IRQ_AUTO)
458 instance->irq = overrides[current_override].irq;
459 else
460 instance->irq = NCR5380_probe_irq(instance, 0xffff);
461
462 if (instance->irq != SCSI_IRQ_NONE)
463 if (request_irq(instance->irq, generic_NCR5380_intr,
464 0, "NCR5380", instance)) {
465 printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
466 instance->irq = SCSI_IRQ_NONE;
467 }
468
469 if (instance->irq == SCSI_IRQ_NONE) {
470 printk(KERN_INFO "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
471 printk(KERN_INFO "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
472 }
473
474 printk(KERN_INFO "scsi%d : at " STRVAL(NCR5380_map_name) " 0x%x", instance->host_no, (unsigned int) instance->NCR5380_instance_name);
475 if (instance->irq == SCSI_IRQ_NONE)
476 printk(" interrupts disabled");
477 else
478 printk(" irq %d", instance->irq);
479 printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, GENERIC_NCR5380_PUBLIC_RELEASE);
480 NCR5380_print_options(instance);
481 printk("\n");
482
483 ++current_override;
484 ++count;
485 }
486 return count;
487}
488
489/**
490 * generic_NCR5380_info - reporting string
491 * @host: NCR5380 to report on
492 *
493 * Report driver information for the NCR5380
494 */
495
496const char *generic_NCR5380_info(struct Scsi_Host *host)
497{
498 static const char string[] = "Generic NCR5380/53C400 Driver";
499 return string;
500}
501
502/**
503 * generic_NCR5380_release_resources - free resources
504 * @instance: host adapter to clean up
505 *
506 * Free the generic interface resources from this adapter.
507 *
508 * Locks: none
509 */
510
511int generic_NCR5380_release_resources(struct Scsi_Host *instance)
512{
513 NCR5380_local_declare();
514 NCR5380_setup(instance);
515
516 if (instance->irq != SCSI_IRQ_NONE)
517 free_irq(instance->irq, instance);
518 NCR5380_exit(instance);
519
520#ifndef SCSI_G_NCR5380_MEM
521 release_region(instance->NCR5380_instance_name, instance->n_io_port);
522#else
523 iounmap(((struct NCR5380_hostdata *)instance->hostdata)->iomem);
524 release_mem_region(instance->NCR5380_instance_name, NCR5380_region_size);
525#endif
526
527
528 return 0;
529}
530
531#ifdef BIOSPARAM
532/**
533 * generic_NCR5380_biosparam
534 * @disk: disk to compute geometry for
535 * @dev: device identifier for this disk
536 * @ip: sizes to fill in
537 *
538 * Generates a BIOS / DOS compatible H-C-S mapping for the specified
539 * device / size.
540 *
541 * XXX Most SCSI boards use this mapping, I could be incorrect. Someone
542 * using hard disks on a trantor should verify that this mapping
543 * corresponds to that used by the BIOS / ASPI driver by running the linux
544 * fdisk program and matching the H_C_S coordinates to what DOS uses.
545 *
546 * Locks: none
547 */
548
549static int
550generic_NCR5380_biosparam(struct scsi_device *sdev, struct block_device *bdev,
551 sector_t capacity, int *ip)
552{
553 ip[0] = 64;
554 ip[1] = 32;
555 ip[2] = capacity >> 11;
556 return 0;
557}
558#endif
559
560#ifdef NCR53C400_PSEUDO_DMA
561
562/**
563 * NCR5380_pread - pseudo DMA read
564 * @instance: adapter to read from
565 * @dst: buffer to read into
566 * @len: buffer length
567 *
568 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
569 * controller
570 */
571
572static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
573{
574 int blocks = len / 128;
575 int start = 0;
576 int bl;
577
578 NCR5380_local_declare();
579 NCR5380_setup(instance);
580
581 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE | CSR_TRANS_DIR);
582 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
583 while (1) {
584 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
585 break;
586 }
587 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
588 printk(KERN_ERR "53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
589 return -1;
590 }
591 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY);
592
593#ifndef SCSI_G_NCR5380_MEM
594 {
595 int i;
596 for (i = 0; i < 128; i++)
597 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
598 }
599#else
600 /* implies SCSI_G_NCR5380_MEM */
601 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
602#endif
603 start += 128;
604 blocks--;
605 }
606
607 if (blocks) {
608 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
609 {
610 // FIXME - no timeout
611 }
612
613#ifndef SCSI_G_NCR5380_MEM
614 {
615 int i;
616 for (i = 0; i < 128; i++)
617 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
618 }
619#else
620 /* implies SCSI_G_NCR5380_MEM */
621 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
622#endif
623 start += 128;
624 blocks--;
625 }
626
627 if (!(NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
628 printk("53C400r: no 53C80 gated irq after transfer");
629
630#if 0
631 /*
632 * DON'T DO THIS - THEY NEVER ARRIVE!
633 */
634 printk("53C400r: Waiting for 53C80 registers\n");
635 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG)
636 ;
637#endif
638 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
639 printk(KERN_ERR "53C400r: no end dma signal\n");
640
641 NCR5380_write(MODE_REG, MR_BASE);
642 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
643 return 0;
644}
645
646/**
647 * NCR5380_write - pseudo DMA write
648 * @instance: adapter to read from
649 * @dst: buffer to read into
650 * @len: buffer length
651 *
652 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
653 * controller
654 */
655
656static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
657{
658 int blocks = len / 128;
659 int start = 0;
660 int bl;
661 int i;
662
663 NCR5380_local_declare();
664 NCR5380_setup(instance);
665
666 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);
667 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
668 while (1) {
669 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
670 printk(KERN_ERR "53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
671 return -1;
672 }
673
674 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
675 break;
676 }
677 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
678 ; // FIXME - timeout
679#ifndef SCSI_G_NCR5380_MEM
680 {
681 for (i = 0; i < 128; i++)
682 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
683 }
684#else
685 /* implies SCSI_G_NCR5380_MEM */
686 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
687#endif
688 start += 128;
689 blocks--;
690 }
691 if (blocks) {
692 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
693 ; // FIXME - no timeout
694
695#ifndef SCSI_G_NCR5380_MEM
696 {
697 for (i = 0; i < 128; i++)
698 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
699 }
700#else
701 /* implies SCSI_G_NCR5380_MEM */
702 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
703#endif
704 start += 128;
705 blocks--;
706 }
707
708#if 0
709 printk("53C400w: waiting for registers to be available\n");
710 THEY NEVER DO ! while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG);
711 printk("53C400w: Got em\n");
712#endif
713
714 /* Let's wait for this instead - could be ugly */
715 /* All documentation says to check for this. Maybe my hardware is too
716 * fast. Waiting for it seems to work fine! KLL
717 */
718 while (!(i = NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
719 ; // FIXME - no timeout
720
721 /*
722 * I know. i is certainly != 0 here but the loop is new. See previous
723 * comment.
724 */
725 if (i) {
726 if (!((i = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER))
727 printk(KERN_ERR "53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i);
728 } else
729 printk(KERN_ERR "53C400w: no 53C80 gated irq after transfer (last block)\n");
730
731#if 0
732 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) {
733 printk(KERN_ERR "53C400w: no end dma signal\n");
734 }
735#endif
736 while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
737 ; // TIMEOUT
738 return 0;
739}
740#endif /* PSEUDO_DMA */
741
742/*
743 * Include the NCR5380 core code that we build our driver around
744 */
745
746#include "NCR5380.c"
747
748#define PRINTP(x) seq_printf(m, x)
749#define ANDP ,
750
751static void sprint_opcode(struct seq_file *m, int opcode)
752{
753 PRINTP("0x%02x " ANDP opcode);
754}
755
756static void sprint_command(struct seq_file *m, unsigned char *command)
757{
758 int i, s;
759 sprint_opcode(m, command[0]);
760 for (i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i)
761 PRINTP("%02x " ANDP command[i]);
762 PRINTP("\n");
763}
764
765/**
766 * sprintf_Scsi_Cmnd - print a scsi command
767 * @m: seq_fil to print into
768 * @cmd: SCSI command block
769 *
770 * Print out the target and command data in hex
771 */
772
773static void sprint_Scsi_Cmnd(struct seq_file *m, Scsi_Cmnd * cmd)
774{
775 PRINTP("host number %d destination target %d, lun %d\n" ANDP cmd->device->host->host_no ANDP cmd->device->id ANDP cmd->device->lun);
776 PRINTP(" command = ");
777 sprint_command(m, cmd->cmnd);
778}
779
780/**
781 * generic_NCR5380_proc_info - /proc for NCR5380 driver
782 * @buffer: buffer to print into
783 * @start: start position
784 * @offset: offset into buffer
785 * @len: length
786 * @hostno: instance to affect
787 * @inout: read/write
788 *
789 * Provide the procfs information for the 5380 controller. We fill
790 * this with useful debugging information including the commands
791 * being executed, disconnected command queue and the statistical
792 * data
793 *
794 * Locks: global cli/lock for queue walk
795 */
796
797static int generic_NCR5380_show_info(struct seq_file *m, struct Scsi_Host *scsi_ptr)
798{
799 NCR5380_local_declare();
800 unsigned long flags;
801 unsigned char status;
802 int i;
803 Scsi_Cmnd *ptr;
804 struct NCR5380_hostdata *hostdata;
805#ifdef NCR5380_STATS
806 struct scsi_device *dev;
807#endif
808
809 NCR5380_setup(scsi_ptr);
810 hostdata = (struct NCR5380_hostdata *) scsi_ptr->hostdata;
811
812 spin_lock_irqsave(scsi_ptr->host_lock, flags);
813 PRINTP("SCSI host number %d : %s\n" ANDP scsi_ptr->host_no ANDP scsi_ptr->hostt->name);
814 PRINTP("Generic NCR5380 driver version %d\n" ANDP GENERIC_NCR5380_PUBLIC_RELEASE);
815 PRINTP("NCR5380 core version %d\n" ANDP NCR5380_PUBLIC_RELEASE);
816#ifdef NCR53C400
817 PRINTP("NCR53C400 extension version %d\n" ANDP NCR53C400_PUBLIC_RELEASE);
818 PRINTP("NCR53C400 card%s detected\n" ANDP(((struct NCR5380_hostdata *) scsi_ptr->hostdata)->flags & FLAG_NCR53C400) ? "" : " not");
819# if NCR53C400_PSEUDO_DMA
820 PRINTP("NCR53C400 pseudo DMA used\n");
821# endif
822#else
823 PRINTP("NO NCR53C400 driver extensions\n");
824#endif
825 PRINTP("Using %s mapping at %s 0x%lx, " ANDP STRVAL(NCR5380_map_config) ANDP STRVAL(NCR5380_map_name) ANDP scsi_ptr->NCR5380_instance_name);
826 if (scsi_ptr->irq == SCSI_IRQ_NONE)
827 PRINTP("no interrupt\n");
828 else
829 PRINTP("on interrupt %d\n" ANDP scsi_ptr->irq);
830
831#ifdef NCR5380_STATS
832 if (hostdata->connected || hostdata->issue_queue || hostdata->disconnected_queue)
833 PRINTP("There are commands pending, transfer rates may be crud\n");
834 if (hostdata->pendingr)
835 PRINTP(" %d pending reads" ANDP hostdata->pendingr);
836 if (hostdata->pendingw)
837 PRINTP(" %d pending writes" ANDP hostdata->pendingw);
838 if (hostdata->pendingr || hostdata->pendingw)
839 PRINTP("\n");
840 shost_for_each_device(dev, scsi_ptr) {
841 unsigned long br = hostdata->bytes_read[dev->id];
842 unsigned long bw = hostdata->bytes_write[dev->id];
843 long tr = hostdata->time_read[dev->id] / HZ;
844 long tw = hostdata->time_write[dev->id] / HZ;
845
846 PRINTP(" T:%d %s " ANDP dev->id ANDP scsi_device_type(dev->type));
847 for (i = 0; i < 8; i++)
848 if (dev->vendor[i] >= 0x20)
849 seq_putc(m, dev->vendor[i]);
850 seq_putc(m, ' ');
851 for (i = 0; i < 16; i++)
852 if (dev->model[i] >= 0x20)
853 seq_putc(m, dev->model[i]);
854 seq_putc(m, ' ');
855 for (i = 0; i < 4; i++)
856 if (dev->rev[i] >= 0x20)
857 seq_putc(m, dev->rev[i]);
858 seq_putc(m, ' ');
859
860 PRINTP("\n%10ld kb read in %5ld secs" ANDP br / 1024 ANDP tr);
861 if (tr)
862 PRINTP(" @ %5ld bps" ANDP br / tr);
863
864 PRINTP("\n%10ld kb written in %5ld secs" ANDP bw / 1024 ANDP tw);
865 if (tw)
866 PRINTP(" @ %5ld bps" ANDP bw / tw);
867 PRINTP("\n");
868 }
869#endif
870
871 status = NCR5380_read(STATUS_REG);
872 if (!(status & SR_REQ))
873 PRINTP("REQ not asserted, phase unknown.\n");
874 else {
875 for (i = 0; (phases[i].value != PHASE_UNKNOWN) && (phases[i].value != (status & PHASE_MASK)); ++i);
876 PRINTP("Phase %s\n" ANDP phases[i].name);
877 }
878
879 if (!hostdata->connected) {
880 PRINTP("No currently connected command\n");
881 } else {
882 sprint_Scsi_Cmnd(m, (Scsi_Cmnd *) hostdata->connected);
883 }
884
885 PRINTP("issue_queue\n");
886
887 for (ptr = (Scsi_Cmnd *) hostdata->issue_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
888 sprint_Scsi_Cmnd(m, ptr);
889
890 PRINTP("disconnected_queue\n");
891
892 for (ptr = (Scsi_Cmnd *) hostdata->disconnected_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
893 sprint_Scsi_Cmnd(m, ptr);
894
895 spin_unlock_irqrestore(scsi_ptr->host_lock, flags);
896 return 0;
897}
898
899#undef PRINTP
900#undef ANDP
901
902static struct scsi_host_template driver_template = {
903 .show_info = generic_NCR5380_show_info,
904 .name = "Generic NCR5380/NCR53C400 Scsi Driver",
905 .detect = generic_NCR5380_detect,
906 .release = generic_NCR5380_release_resources,
907 .info = generic_NCR5380_info,
908 .queuecommand = generic_NCR5380_queue_command,
909 .eh_abort_handler = generic_NCR5380_abort,
910 .eh_bus_reset_handler = generic_NCR5380_bus_reset,
911 .bios_param = NCR5380_BIOSPARAM,
912 .can_queue = CAN_QUEUE,
913 .this_id = 7,
914 .sg_tablesize = SG_ALL,
915 .cmd_per_lun = CMD_PER_LUN,
916 .use_clustering = DISABLE_CLUSTERING,
917};
918#include <linux/module.h>
919#include "scsi_module.c"
920
921module_param(ncr_irq, int, 0);
922module_param(ncr_dma, int, 0);
923module_param(ncr_addr, int, 0);
924module_param(ncr_5380, int, 0);
925module_param(ncr_53c400, int, 0);
926module_param(ncr_53c400a, int, 0);
927module_param(dtc_3181e, int, 0);
928MODULE_LICENSE("GPL");
929
930#ifndef SCSI_G_NCR5380_MEM
931static struct isapnp_device_id id_table[] = {
932 {
933 ISAPNP_ANY_ID, ISAPNP_ANY_ID,
934 ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e),
935 0},
936 {0}
937};
938
939MODULE_DEVICE_TABLE(isapnp, id_table);
940#endif
941
942__setup("ncr5380=", do_NCR5380_setup);
943__setup("ncr53c400=", do_NCR53C400_setup);
944__setup("ncr53c400a=", do_NCR53C400A_setup);
945__setup("dtc3181e=", do_DTC3181E_setup);