Loading...
1/*
2 * xHCI host controller driver
3 *
4 * Copyright (C) 2008 Intel Corp.
5 *
6 * Author: Sarah Sharp
7 * Some code borrowed from the Linux EHCI driver.
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
12 *
13 * This program is distributed in the hope that it will be useful, but
14 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
15 * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
16 * for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software Foundation,
20 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21 */
22
23#include <asm/unaligned.h>
24
25#include "xhci.h"
26
27#define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
28#define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
29 PORT_RC | PORT_PLC | PORT_PE)
30
31static void xhci_common_hub_descriptor(struct xhci_hcd *xhci,
32 struct usb_hub_descriptor *desc, int ports)
33{
34 u16 temp;
35
36 desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.9 says 20ms max */
37 desc->bHubContrCurrent = 0;
38
39 desc->bNbrPorts = ports;
40 /* Ugh, these should be #defines, FIXME */
41 /* Using table 11-13 in USB 2.0 spec. */
42 temp = 0;
43 /* Bits 1:0 - support port power switching, or power always on */
44 if (HCC_PPC(xhci->hcc_params))
45 temp |= 0x0001;
46 else
47 temp |= 0x0002;
48 /* Bit 2 - root hubs are not part of a compound device */
49 /* Bits 4:3 - individual port over current protection */
50 temp |= 0x0008;
51 /* Bits 6:5 - no TTs in root ports */
52 /* Bit 7 - no port indicators */
53 desc->wHubCharacteristics = cpu_to_le16(temp);
54}
55
56/* Fill in the USB 2.0 roothub descriptor */
57static void xhci_usb2_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
58 struct usb_hub_descriptor *desc)
59{
60 int ports;
61 u16 temp;
62 __u8 port_removable[(USB_MAXCHILDREN + 1 + 7) / 8];
63 u32 portsc;
64 unsigned int i;
65
66 ports = xhci->num_usb2_ports;
67
68 xhci_common_hub_descriptor(xhci, desc, ports);
69 desc->bDescriptorType = 0x29;
70 temp = 1 + (ports / 8);
71 desc->bDescLength = 7 + 2 * temp;
72
73 /* The Device Removable bits are reported on a byte granularity.
74 * If the port doesn't exist within that byte, the bit is set to 0.
75 */
76 memset(port_removable, 0, sizeof(port_removable));
77 for (i = 0; i < ports; i++) {
78 portsc = xhci_readl(xhci, xhci->usb3_ports[i]);
79 /* If a device is removable, PORTSC reports a 0, same as in the
80 * hub descriptor DeviceRemovable bits.
81 */
82 if (portsc & PORT_DEV_REMOVE)
83 /* This math is hairy because bit 0 of DeviceRemovable
84 * is reserved, and bit 1 is for port 1, etc.
85 */
86 port_removable[(i + 1) / 8] |= 1 << ((i + 1) % 8);
87 }
88
89 /* ch11.h defines a hub descriptor that has room for USB_MAXCHILDREN
90 * ports on it. The USB 2.0 specification says that there are two
91 * variable length fields at the end of the hub descriptor:
92 * DeviceRemovable and PortPwrCtrlMask. But since we can have less than
93 * USB_MAXCHILDREN ports, we may need to use the DeviceRemovable array
94 * to set PortPwrCtrlMask bits. PortPwrCtrlMask must always be set to
95 * 0xFF, so we initialize the both arrays (DeviceRemovable and
96 * PortPwrCtrlMask) to 0xFF. Then we set the DeviceRemovable for each
97 * set of ports that actually exist.
98 */
99 memset(desc->u.hs.DeviceRemovable, 0xff,
100 sizeof(desc->u.hs.DeviceRemovable));
101 memset(desc->u.hs.PortPwrCtrlMask, 0xff,
102 sizeof(desc->u.hs.PortPwrCtrlMask));
103
104 for (i = 0; i < (ports + 1 + 7) / 8; i++)
105 memset(&desc->u.hs.DeviceRemovable[i], port_removable[i],
106 sizeof(__u8));
107}
108
109/* Fill in the USB 3.0 roothub descriptor */
110static void xhci_usb3_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
111 struct usb_hub_descriptor *desc)
112{
113 int ports;
114 u16 port_removable;
115 u32 portsc;
116 unsigned int i;
117
118 ports = xhci->num_usb3_ports;
119 xhci_common_hub_descriptor(xhci, desc, ports);
120 desc->bDescriptorType = 0x2a;
121 desc->bDescLength = 12;
122
123 /* header decode latency should be zero for roothubs,
124 * see section 4.23.5.2.
125 */
126 desc->u.ss.bHubHdrDecLat = 0;
127 desc->u.ss.wHubDelay = 0;
128
129 port_removable = 0;
130 /* bit 0 is reserved, bit 1 is for port 1, etc. */
131 for (i = 0; i < ports; i++) {
132 portsc = xhci_readl(xhci, xhci->usb3_ports[i]);
133 if (portsc & PORT_DEV_REMOVE)
134 port_removable |= 1 << (i + 1);
135 }
136 memset(&desc->u.ss.DeviceRemovable,
137 (__force __u16) cpu_to_le16(port_removable),
138 sizeof(__u16));
139}
140
141static void xhci_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
142 struct usb_hub_descriptor *desc)
143{
144
145 if (hcd->speed == HCD_USB3)
146 xhci_usb3_hub_descriptor(hcd, xhci, desc);
147 else
148 xhci_usb2_hub_descriptor(hcd, xhci, desc);
149
150}
151
152static unsigned int xhci_port_speed(unsigned int port_status)
153{
154 if (DEV_LOWSPEED(port_status))
155 return USB_PORT_STAT_LOW_SPEED;
156 if (DEV_HIGHSPEED(port_status))
157 return USB_PORT_STAT_HIGH_SPEED;
158 /*
159 * FIXME: Yes, we should check for full speed, but the core uses that as
160 * a default in portspeed() in usb/core/hub.c (which is the only place
161 * USB_PORT_STAT_*_SPEED is used).
162 */
163 return 0;
164}
165
166/*
167 * These bits are Read Only (RO) and should be saved and written to the
168 * registers: 0, 3, 10:13, 30
169 * connect status, over-current status, port speed, and device removable.
170 * connect status and port speed are also sticky - meaning they're in
171 * the AUX well and they aren't changed by a hot, warm, or cold reset.
172 */
173#define XHCI_PORT_RO ((1<<0) | (1<<3) | (0xf<<10) | (1<<30))
174/*
175 * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit:
176 * bits 5:8, 9, 14:15, 25:27
177 * link state, port power, port indicator state, "wake on" enable state
178 */
179#define XHCI_PORT_RWS ((0xf<<5) | (1<<9) | (0x3<<14) | (0x7<<25))
180/*
181 * These bits are RW; writing a 1 sets the bit, writing a 0 has no effect:
182 * bit 4 (port reset)
183 */
184#define XHCI_PORT_RW1S ((1<<4))
185/*
186 * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect:
187 * bits 1, 17, 18, 19, 20, 21, 22, 23
188 * port enable/disable, and
189 * change bits: connect, PED, warm port reset changed (reserved zero for USB 2.0 ports),
190 * over-current, reset, link state, and L1 change
191 */
192#define XHCI_PORT_RW1CS ((1<<1) | (0x7f<<17))
193/*
194 * Bit 16 is RW, and writing a '1' to it causes the link state control to be
195 * latched in
196 */
197#define XHCI_PORT_RW ((1<<16))
198/*
199 * These bits are Reserved Zero (RsvdZ) and zero should be written to them:
200 * bits 2, 24, 28:31
201 */
202#define XHCI_PORT_RZ ((1<<2) | (1<<24) | (0xf<<28))
203
204/*
205 * Given a port state, this function returns a value that would result in the
206 * port being in the same state, if the value was written to the port status
207 * control register.
208 * Save Read Only (RO) bits and save read/write bits where
209 * writing a 0 clears the bit and writing a 1 sets the bit (RWS).
210 * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect.
211 */
212u32 xhci_port_state_to_neutral(u32 state)
213{
214 /* Save read-only status and port state */
215 return (state & XHCI_PORT_RO) | (state & XHCI_PORT_RWS);
216}
217
218/*
219 * find slot id based on port number.
220 * @port: The one-based port number from one of the two split roothubs.
221 */
222int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
223 u16 port)
224{
225 int slot_id;
226 int i;
227 enum usb_device_speed speed;
228
229 slot_id = 0;
230 for (i = 0; i < MAX_HC_SLOTS; i++) {
231 if (!xhci->devs[i])
232 continue;
233 speed = xhci->devs[i]->udev->speed;
234 if (((speed == USB_SPEED_SUPER) == (hcd->speed == HCD_USB3))
235 && xhci->devs[i]->port == port) {
236 slot_id = i;
237 break;
238 }
239 }
240
241 return slot_id;
242}
243
244/*
245 * Stop device
246 * It issues stop endpoint command for EP 0 to 30. And wait the last command
247 * to complete.
248 * suspend will set to 1, if suspend bit need to set in command.
249 */
250static int xhci_stop_device(struct xhci_hcd *xhci, int slot_id, int suspend)
251{
252 struct xhci_virt_device *virt_dev;
253 struct xhci_command *cmd;
254 unsigned long flags;
255 int timeleft;
256 int ret;
257 int i;
258
259 ret = 0;
260 virt_dev = xhci->devs[slot_id];
261 cmd = xhci_alloc_command(xhci, false, true, GFP_NOIO);
262 if (!cmd) {
263 xhci_dbg(xhci, "Couldn't allocate command structure.\n");
264 return -ENOMEM;
265 }
266
267 spin_lock_irqsave(&xhci->lock, flags);
268 for (i = LAST_EP_INDEX; i > 0; i--) {
269 if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
270 xhci_queue_stop_endpoint(xhci, slot_id, i, suspend);
271 }
272 cmd->command_trb = xhci->cmd_ring->enqueue;
273 list_add_tail(&cmd->cmd_list, &virt_dev->cmd_list);
274 xhci_queue_stop_endpoint(xhci, slot_id, 0, suspend);
275 xhci_ring_cmd_db(xhci);
276 spin_unlock_irqrestore(&xhci->lock, flags);
277
278 /* Wait for last stop endpoint command to finish */
279 timeleft = wait_for_completion_interruptible_timeout(
280 cmd->completion,
281 USB_CTRL_SET_TIMEOUT);
282 if (timeleft <= 0) {
283 xhci_warn(xhci, "%s while waiting for stop endpoint command\n",
284 timeleft == 0 ? "Timeout" : "Signal");
285 spin_lock_irqsave(&xhci->lock, flags);
286 /* The timeout might have raced with the event ring handler, so
287 * only delete from the list if the item isn't poisoned.
288 */
289 if (cmd->cmd_list.next != LIST_POISON1)
290 list_del(&cmd->cmd_list);
291 spin_unlock_irqrestore(&xhci->lock, flags);
292 ret = -ETIME;
293 goto command_cleanup;
294 }
295
296command_cleanup:
297 xhci_free_command(xhci, cmd);
298 return ret;
299}
300
301/*
302 * Ring device, it rings the all doorbells unconditionally.
303 */
304void xhci_ring_device(struct xhci_hcd *xhci, int slot_id)
305{
306 int i;
307
308 for (i = 0; i < LAST_EP_INDEX + 1; i++)
309 if (xhci->devs[slot_id]->eps[i].ring &&
310 xhci->devs[slot_id]->eps[i].ring->dequeue)
311 xhci_ring_ep_doorbell(xhci, slot_id, i, 0);
312
313 return;
314}
315
316static void xhci_disable_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
317 u16 wIndex, __le32 __iomem *addr, u32 port_status)
318{
319 /* Don't allow the USB core to disable SuperSpeed ports. */
320 if (hcd->speed == HCD_USB3) {
321 xhci_dbg(xhci, "Ignoring request to disable "
322 "SuperSpeed port.\n");
323 return;
324 }
325
326 /* Write 1 to disable the port */
327 xhci_writel(xhci, port_status | PORT_PE, addr);
328 port_status = xhci_readl(xhci, addr);
329 xhci_dbg(xhci, "disable port, actual port %d status = 0x%x\n",
330 wIndex, port_status);
331}
332
333static void xhci_clear_port_change_bit(struct xhci_hcd *xhci, u16 wValue,
334 u16 wIndex, __le32 __iomem *addr, u32 port_status)
335{
336 char *port_change_bit;
337 u32 status;
338
339 switch (wValue) {
340 case USB_PORT_FEAT_C_RESET:
341 status = PORT_RC;
342 port_change_bit = "reset";
343 break;
344 case USB_PORT_FEAT_C_BH_PORT_RESET:
345 status = PORT_WRC;
346 port_change_bit = "warm(BH) reset";
347 break;
348 case USB_PORT_FEAT_C_CONNECTION:
349 status = PORT_CSC;
350 port_change_bit = "connect";
351 break;
352 case USB_PORT_FEAT_C_OVER_CURRENT:
353 status = PORT_OCC;
354 port_change_bit = "over-current";
355 break;
356 case USB_PORT_FEAT_C_ENABLE:
357 status = PORT_PEC;
358 port_change_bit = "enable/disable";
359 break;
360 case USB_PORT_FEAT_C_SUSPEND:
361 status = PORT_PLC;
362 port_change_bit = "suspend/resume";
363 break;
364 case USB_PORT_FEAT_C_PORT_LINK_STATE:
365 status = PORT_PLC;
366 port_change_bit = "link state";
367 break;
368 default:
369 /* Should never happen */
370 return;
371 }
372 /* Change bits are all write 1 to clear */
373 xhci_writel(xhci, port_status | status, addr);
374 port_status = xhci_readl(xhci, addr);
375 xhci_dbg(xhci, "clear port %s change, actual port %d status = 0x%x\n",
376 port_change_bit, wIndex, port_status);
377}
378
379static int xhci_get_ports(struct usb_hcd *hcd, __le32 __iomem ***port_array)
380{
381 int max_ports;
382 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
383
384 if (hcd->speed == HCD_USB3) {
385 max_ports = xhci->num_usb3_ports;
386 *port_array = xhci->usb3_ports;
387 } else {
388 max_ports = xhci->num_usb2_ports;
389 *port_array = xhci->usb2_ports;
390 }
391
392 return max_ports;
393}
394
395int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
396 u16 wIndex, char *buf, u16 wLength)
397{
398 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
399 int max_ports;
400 unsigned long flags;
401 u32 temp, temp1, status;
402 int retval = 0;
403 __le32 __iomem **port_array;
404 int slot_id;
405 struct xhci_bus_state *bus_state;
406 u16 link_state = 0;
407
408 max_ports = xhci_get_ports(hcd, &port_array);
409 bus_state = &xhci->bus_state[hcd_index(hcd)];
410
411 spin_lock_irqsave(&xhci->lock, flags);
412 switch (typeReq) {
413 case GetHubStatus:
414 /* No power source, over-current reported per port */
415 memset(buf, 0, 4);
416 break;
417 case GetHubDescriptor:
418 /* Check to make sure userspace is asking for the USB 3.0 hub
419 * descriptor for the USB 3.0 roothub. If not, we stall the
420 * endpoint, like external hubs do.
421 */
422 if (hcd->speed == HCD_USB3 &&
423 (wLength < USB_DT_SS_HUB_SIZE ||
424 wValue != (USB_DT_SS_HUB << 8))) {
425 xhci_dbg(xhci, "Wrong hub descriptor type for "
426 "USB 3.0 roothub.\n");
427 goto error;
428 }
429 xhci_hub_descriptor(hcd, xhci,
430 (struct usb_hub_descriptor *) buf);
431 break;
432 case GetPortStatus:
433 if (!wIndex || wIndex > max_ports)
434 goto error;
435 wIndex--;
436 status = 0;
437 temp = xhci_readl(xhci, port_array[wIndex]);
438 if (temp == 0xffffffff) {
439 retval = -ENODEV;
440 break;
441 }
442 xhci_dbg(xhci, "get port status, actual port %d status = 0x%x\n", wIndex, temp);
443
444 /* wPortChange bits */
445 if (temp & PORT_CSC)
446 status |= USB_PORT_STAT_C_CONNECTION << 16;
447 if (temp & PORT_PEC)
448 status |= USB_PORT_STAT_C_ENABLE << 16;
449 if ((temp & PORT_OCC))
450 status |= USB_PORT_STAT_C_OVERCURRENT << 16;
451 if ((temp & PORT_RC))
452 status |= USB_PORT_STAT_C_RESET << 16;
453 /* USB3.0 only */
454 if (hcd->speed == HCD_USB3) {
455 if ((temp & PORT_PLC))
456 status |= USB_PORT_STAT_C_LINK_STATE << 16;
457 if ((temp & PORT_WRC))
458 status |= USB_PORT_STAT_C_BH_RESET << 16;
459 }
460
461 if (hcd->speed != HCD_USB3) {
462 if ((temp & PORT_PLS_MASK) == XDEV_U3
463 && (temp & PORT_POWER))
464 status |= USB_PORT_STAT_SUSPEND;
465 }
466 if ((temp & PORT_PLS_MASK) == XDEV_RESUME &&
467 !DEV_SUPERSPEED(temp)) {
468 if ((temp & PORT_RESET) || !(temp & PORT_PE))
469 goto error;
470 if (time_after_eq(jiffies,
471 bus_state->resume_done[wIndex])) {
472 xhci_dbg(xhci, "Resume USB2 port %d\n",
473 wIndex + 1);
474 bus_state->resume_done[wIndex] = 0;
475 temp1 = xhci_port_state_to_neutral(temp);
476 temp1 &= ~PORT_PLS_MASK;
477 temp1 |= PORT_LINK_STROBE | XDEV_U0;
478 xhci_writel(xhci, temp1, port_array[wIndex]);
479
480 xhci_dbg(xhci, "set port %d resume\n",
481 wIndex + 1);
482 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
483 wIndex + 1);
484 if (!slot_id) {
485 xhci_dbg(xhci, "slot_id is zero\n");
486 goto error;
487 }
488 xhci_ring_device(xhci, slot_id);
489 bus_state->port_c_suspend |= 1 << wIndex;
490 bus_state->suspended_ports &= ~(1 << wIndex);
491 } else {
492 /*
493 * The resume has been signaling for less than
494 * 20ms. Report the port status as SUSPEND,
495 * let the usbcore check port status again
496 * and clear resume signaling later.
497 */
498 status |= USB_PORT_STAT_SUSPEND;
499 }
500 }
501 if ((temp & PORT_PLS_MASK) == XDEV_U0
502 && (temp & PORT_POWER)
503 && (bus_state->suspended_ports & (1 << wIndex))) {
504 bus_state->suspended_ports &= ~(1 << wIndex);
505 if (hcd->speed != HCD_USB3)
506 bus_state->port_c_suspend |= 1 << wIndex;
507 }
508 if (temp & PORT_CONNECT) {
509 status |= USB_PORT_STAT_CONNECTION;
510 status |= xhci_port_speed(temp);
511 }
512 if (temp & PORT_PE)
513 status |= USB_PORT_STAT_ENABLE;
514 if (temp & PORT_OC)
515 status |= USB_PORT_STAT_OVERCURRENT;
516 if (temp & PORT_RESET)
517 status |= USB_PORT_STAT_RESET;
518 if (temp & PORT_POWER) {
519 if (hcd->speed == HCD_USB3)
520 status |= USB_SS_PORT_STAT_POWER;
521 else
522 status |= USB_PORT_STAT_POWER;
523 }
524 /* Port Link State */
525 if (hcd->speed == HCD_USB3) {
526 /* resume state is a xHCI internal state.
527 * Do not report it to usb core.
528 */
529 if ((temp & PORT_PLS_MASK) != XDEV_RESUME)
530 status |= (temp & PORT_PLS_MASK);
531 }
532 if (bus_state->port_c_suspend & (1 << wIndex))
533 status |= 1 << USB_PORT_FEAT_C_SUSPEND;
534 xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
535 put_unaligned(cpu_to_le32(status), (__le32 *) buf);
536 break;
537 case SetPortFeature:
538 if (wValue == USB_PORT_FEAT_LINK_STATE)
539 link_state = (wIndex & 0xff00) >> 3;
540 wIndex &= 0xff;
541 if (!wIndex || wIndex > max_ports)
542 goto error;
543 wIndex--;
544 temp = xhci_readl(xhci, port_array[wIndex]);
545 if (temp == 0xffffffff) {
546 retval = -ENODEV;
547 break;
548 }
549 temp = xhci_port_state_to_neutral(temp);
550 /* FIXME: What new port features do we need to support? */
551 switch (wValue) {
552 case USB_PORT_FEAT_SUSPEND:
553 temp = xhci_readl(xhci, port_array[wIndex]);
554 /* In spec software should not attempt to suspend
555 * a port unless the port reports that it is in the
556 * enabled (PED = ‘1’,PLS < ‘3’) state.
557 */
558 if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
559 || (temp & PORT_PLS_MASK) >= XDEV_U3) {
560 xhci_warn(xhci, "USB core suspending device "
561 "not in U0/U1/U2.\n");
562 goto error;
563 }
564
565 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
566 wIndex + 1);
567 if (!slot_id) {
568 xhci_warn(xhci, "slot_id is zero\n");
569 goto error;
570 }
571 /* unlock to execute stop endpoint commands */
572 spin_unlock_irqrestore(&xhci->lock, flags);
573 xhci_stop_device(xhci, slot_id, 1);
574 spin_lock_irqsave(&xhci->lock, flags);
575
576 temp = xhci_port_state_to_neutral(temp);
577 temp &= ~PORT_PLS_MASK;
578 temp |= PORT_LINK_STROBE | XDEV_U3;
579 xhci_writel(xhci, temp, port_array[wIndex]);
580
581 spin_unlock_irqrestore(&xhci->lock, flags);
582 msleep(10); /* wait device to enter */
583 spin_lock_irqsave(&xhci->lock, flags);
584
585 temp = xhci_readl(xhci, port_array[wIndex]);
586 bus_state->suspended_ports |= 1 << wIndex;
587 break;
588 case USB_PORT_FEAT_LINK_STATE:
589 temp = xhci_readl(xhci, port_array[wIndex]);
590 /* Software should not attempt to set
591 * port link state above '5' (Rx.Detect) and the port
592 * must be enabled.
593 */
594 if ((temp & PORT_PE) == 0 ||
595 (link_state > USB_SS_PORT_LS_RX_DETECT)) {
596 xhci_warn(xhci, "Cannot set link state.\n");
597 goto error;
598 }
599
600 if (link_state == USB_SS_PORT_LS_U3) {
601 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
602 wIndex + 1);
603 if (slot_id) {
604 /* unlock to execute stop endpoint
605 * commands */
606 spin_unlock_irqrestore(&xhci->lock,
607 flags);
608 xhci_stop_device(xhci, slot_id, 1);
609 spin_lock_irqsave(&xhci->lock, flags);
610 }
611 }
612
613 temp = xhci_port_state_to_neutral(temp);
614 temp &= ~PORT_PLS_MASK;
615 temp |= PORT_LINK_STROBE | link_state;
616 xhci_writel(xhci, temp, port_array[wIndex]);
617
618 spin_unlock_irqrestore(&xhci->lock, flags);
619 msleep(20); /* wait device to enter */
620 spin_lock_irqsave(&xhci->lock, flags);
621
622 temp = xhci_readl(xhci, port_array[wIndex]);
623 if (link_state == USB_SS_PORT_LS_U3)
624 bus_state->suspended_ports |= 1 << wIndex;
625 break;
626 case USB_PORT_FEAT_POWER:
627 /*
628 * Turn on ports, even if there isn't per-port switching.
629 * HC will report connect events even before this is set.
630 * However, khubd will ignore the roothub events until
631 * the roothub is registered.
632 */
633 xhci_writel(xhci, temp | PORT_POWER,
634 port_array[wIndex]);
635
636 temp = xhci_readl(xhci, port_array[wIndex]);
637 xhci_dbg(xhci, "set port power, actual port %d status = 0x%x\n", wIndex, temp);
638 break;
639 case USB_PORT_FEAT_RESET:
640 temp = (temp | PORT_RESET);
641 xhci_writel(xhci, temp, port_array[wIndex]);
642
643 temp = xhci_readl(xhci, port_array[wIndex]);
644 xhci_dbg(xhci, "set port reset, actual port %d status = 0x%x\n", wIndex, temp);
645 break;
646 case USB_PORT_FEAT_BH_PORT_RESET:
647 temp |= PORT_WR;
648 xhci_writel(xhci, temp, port_array[wIndex]);
649
650 temp = xhci_readl(xhci, port_array[wIndex]);
651 break;
652 default:
653 goto error;
654 }
655 /* unblock any posted writes */
656 temp = xhci_readl(xhci, port_array[wIndex]);
657 break;
658 case ClearPortFeature:
659 if (!wIndex || wIndex > max_ports)
660 goto error;
661 wIndex--;
662 temp = xhci_readl(xhci, port_array[wIndex]);
663 if (temp == 0xffffffff) {
664 retval = -ENODEV;
665 break;
666 }
667 /* FIXME: What new port features do we need to support? */
668 temp = xhci_port_state_to_neutral(temp);
669 switch (wValue) {
670 case USB_PORT_FEAT_SUSPEND:
671 temp = xhci_readl(xhci, port_array[wIndex]);
672 xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
673 xhci_dbg(xhci, "PORTSC %04x\n", temp);
674 if (temp & PORT_RESET)
675 goto error;
676 if ((temp & PORT_PLS_MASK) == XDEV_U3) {
677 if ((temp & PORT_PE) == 0)
678 goto error;
679
680 temp = xhci_port_state_to_neutral(temp);
681 temp &= ~PORT_PLS_MASK;
682 temp |= PORT_LINK_STROBE | XDEV_RESUME;
683 xhci_writel(xhci, temp,
684 port_array[wIndex]);
685
686 spin_unlock_irqrestore(&xhci->lock,
687 flags);
688 msleep(20);
689 spin_lock_irqsave(&xhci->lock, flags);
690
691 temp = xhci_readl(xhci,
692 port_array[wIndex]);
693 temp = xhci_port_state_to_neutral(temp);
694 temp &= ~PORT_PLS_MASK;
695 temp |= PORT_LINK_STROBE | XDEV_U0;
696 xhci_writel(xhci, temp,
697 port_array[wIndex]);
698 }
699 bus_state->port_c_suspend |= 1 << wIndex;
700
701 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
702 wIndex + 1);
703 if (!slot_id) {
704 xhci_dbg(xhci, "slot_id is zero\n");
705 goto error;
706 }
707 xhci_ring_device(xhci, slot_id);
708 break;
709 case USB_PORT_FEAT_C_SUSPEND:
710 bus_state->port_c_suspend &= ~(1 << wIndex);
711 case USB_PORT_FEAT_C_RESET:
712 case USB_PORT_FEAT_C_BH_PORT_RESET:
713 case USB_PORT_FEAT_C_CONNECTION:
714 case USB_PORT_FEAT_C_OVER_CURRENT:
715 case USB_PORT_FEAT_C_ENABLE:
716 case USB_PORT_FEAT_C_PORT_LINK_STATE:
717 xhci_clear_port_change_bit(xhci, wValue, wIndex,
718 port_array[wIndex], temp);
719 break;
720 case USB_PORT_FEAT_ENABLE:
721 xhci_disable_port(hcd, xhci, wIndex,
722 port_array[wIndex], temp);
723 break;
724 default:
725 goto error;
726 }
727 break;
728 default:
729error:
730 /* "stall" on error */
731 retval = -EPIPE;
732 }
733 spin_unlock_irqrestore(&xhci->lock, flags);
734 return retval;
735}
736
737/*
738 * Returns 0 if the status hasn't changed, or the number of bytes in buf.
739 * Ports are 0-indexed from the HCD point of view,
740 * and 1-indexed from the USB core pointer of view.
741 *
742 * Note that the status change bits will be cleared as soon as a port status
743 * change event is generated, so we use the saved status from that event.
744 */
745int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
746{
747 unsigned long flags;
748 u32 temp, status;
749 u32 mask;
750 int i, retval;
751 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
752 int max_ports;
753 __le32 __iomem **port_array;
754 struct xhci_bus_state *bus_state;
755
756 max_ports = xhci_get_ports(hcd, &port_array);
757 bus_state = &xhci->bus_state[hcd_index(hcd)];
758
759 /* Initial status is no changes */
760 retval = (max_ports + 8) / 8;
761 memset(buf, 0, retval);
762 status = 0;
763
764 mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC;
765
766 spin_lock_irqsave(&xhci->lock, flags);
767 /* For each port, did anything change? If so, set that bit in buf. */
768 for (i = 0; i < max_ports; i++) {
769 temp = xhci_readl(xhci, port_array[i]);
770 if (temp == 0xffffffff) {
771 retval = -ENODEV;
772 break;
773 }
774 if ((temp & mask) != 0 ||
775 (bus_state->port_c_suspend & 1 << i) ||
776 (bus_state->resume_done[i] && time_after_eq(
777 jiffies, bus_state->resume_done[i]))) {
778 buf[(i + 1) / 8] |= 1 << (i + 1) % 8;
779 status = 1;
780 }
781 }
782 spin_unlock_irqrestore(&xhci->lock, flags);
783 return status ? retval : 0;
784}
785
786#ifdef CONFIG_PM
787
788int xhci_bus_suspend(struct usb_hcd *hcd)
789{
790 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
791 int max_ports, port_index;
792 __le32 __iomem **port_array;
793 struct xhci_bus_state *bus_state;
794 unsigned long flags;
795
796 max_ports = xhci_get_ports(hcd, &port_array);
797 bus_state = &xhci->bus_state[hcd_index(hcd)];
798
799 spin_lock_irqsave(&xhci->lock, flags);
800
801 if (hcd->self.root_hub->do_remote_wakeup) {
802 port_index = max_ports;
803 while (port_index--) {
804 if (bus_state->resume_done[port_index] != 0) {
805 spin_unlock_irqrestore(&xhci->lock, flags);
806 xhci_dbg(xhci, "suspend failed because "
807 "port %d is resuming\n",
808 port_index + 1);
809 return -EBUSY;
810 }
811 }
812 }
813
814 port_index = max_ports;
815 bus_state->bus_suspended = 0;
816 while (port_index--) {
817 /* suspend the port if the port is not suspended */
818 u32 t1, t2;
819 int slot_id;
820
821 t1 = xhci_readl(xhci, port_array[port_index]);
822 t2 = xhci_port_state_to_neutral(t1);
823
824 if ((t1 & PORT_PE) && !(t1 & PORT_PLS_MASK)) {
825 xhci_dbg(xhci, "port %d not suspended\n", port_index);
826 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
827 port_index + 1);
828 if (slot_id) {
829 spin_unlock_irqrestore(&xhci->lock, flags);
830 xhci_stop_device(xhci, slot_id, 1);
831 spin_lock_irqsave(&xhci->lock, flags);
832 }
833 t2 &= ~PORT_PLS_MASK;
834 t2 |= PORT_LINK_STROBE | XDEV_U3;
835 set_bit(port_index, &bus_state->bus_suspended);
836 }
837 if (hcd->self.root_hub->do_remote_wakeup) {
838 if (t1 & PORT_CONNECT) {
839 t2 |= PORT_WKOC_E | PORT_WKDISC_E;
840 t2 &= ~PORT_WKCONN_E;
841 } else {
842 t2 |= PORT_WKOC_E | PORT_WKCONN_E;
843 t2 &= ~PORT_WKDISC_E;
844 }
845 } else
846 t2 &= ~PORT_WAKE_BITS;
847
848 t1 = xhci_port_state_to_neutral(t1);
849 if (t1 != t2)
850 xhci_writel(xhci, t2, port_array[port_index]);
851
852 if (hcd->speed != HCD_USB3) {
853 /* enable remote wake up for USB 2.0 */
854 __le32 __iomem *addr;
855 u32 tmp;
856
857 /* Add one to the port status register address to get
858 * the port power control register address.
859 */
860 addr = port_array[port_index] + 1;
861 tmp = xhci_readl(xhci, addr);
862 tmp |= PORT_RWE;
863 xhci_writel(xhci, tmp, addr);
864 }
865 }
866 hcd->state = HC_STATE_SUSPENDED;
867 bus_state->next_statechange = jiffies + msecs_to_jiffies(10);
868 spin_unlock_irqrestore(&xhci->lock, flags);
869 return 0;
870}
871
872int xhci_bus_resume(struct usb_hcd *hcd)
873{
874 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
875 int max_ports, port_index;
876 __le32 __iomem **port_array;
877 struct xhci_bus_state *bus_state;
878 u32 temp;
879 unsigned long flags;
880
881 max_ports = xhci_get_ports(hcd, &port_array);
882 bus_state = &xhci->bus_state[hcd_index(hcd)];
883
884 if (time_before(jiffies, bus_state->next_statechange))
885 msleep(5);
886
887 spin_lock_irqsave(&xhci->lock, flags);
888 if (!HCD_HW_ACCESSIBLE(hcd)) {
889 spin_unlock_irqrestore(&xhci->lock, flags);
890 return -ESHUTDOWN;
891 }
892
893 /* delay the irqs */
894 temp = xhci_readl(xhci, &xhci->op_regs->command);
895 temp &= ~CMD_EIE;
896 xhci_writel(xhci, temp, &xhci->op_regs->command);
897
898 port_index = max_ports;
899 while (port_index--) {
900 /* Check whether need resume ports. If needed
901 resume port and disable remote wakeup */
902 u32 temp;
903 int slot_id;
904
905 temp = xhci_readl(xhci, port_array[port_index]);
906 if (DEV_SUPERSPEED(temp))
907 temp &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
908 else
909 temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
910 if (test_bit(port_index, &bus_state->bus_suspended) &&
911 (temp & PORT_PLS_MASK)) {
912 if (DEV_SUPERSPEED(temp)) {
913 temp = xhci_port_state_to_neutral(temp);
914 temp &= ~PORT_PLS_MASK;
915 temp |= PORT_LINK_STROBE | XDEV_U0;
916 xhci_writel(xhci, temp, port_array[port_index]);
917 } else {
918 temp = xhci_port_state_to_neutral(temp);
919 temp &= ~PORT_PLS_MASK;
920 temp |= PORT_LINK_STROBE | XDEV_RESUME;
921 xhci_writel(xhci, temp, port_array[port_index]);
922
923 spin_unlock_irqrestore(&xhci->lock, flags);
924 msleep(20);
925 spin_lock_irqsave(&xhci->lock, flags);
926
927 temp = xhci_readl(xhci, port_array[port_index]);
928 temp = xhci_port_state_to_neutral(temp);
929 temp &= ~PORT_PLS_MASK;
930 temp |= PORT_LINK_STROBE | XDEV_U0;
931 xhci_writel(xhci, temp, port_array[port_index]);
932 }
933 /* wait for the port to enter U0 and report port link
934 * state change.
935 */
936 spin_unlock_irqrestore(&xhci->lock, flags);
937 msleep(20);
938 spin_lock_irqsave(&xhci->lock, flags);
939
940 /* Clear PLC */
941 temp = xhci_readl(xhci, port_array[port_index]);
942 if (temp & PORT_PLC) {
943 temp = xhci_port_state_to_neutral(temp);
944 temp |= PORT_PLC;
945 xhci_writel(xhci, temp, port_array[port_index]);
946 }
947
948 slot_id = xhci_find_slot_id_by_port(hcd,
949 xhci, port_index + 1);
950 if (slot_id)
951 xhci_ring_device(xhci, slot_id);
952 } else
953 xhci_writel(xhci, temp, port_array[port_index]);
954
955 if (hcd->speed != HCD_USB3) {
956 /* disable remote wake up for USB 2.0 */
957 __le32 __iomem *addr;
958 u32 tmp;
959
960 /* Add one to the port status register address to get
961 * the port power control register address.
962 */
963 addr = port_array[port_index] + 1;
964 tmp = xhci_readl(xhci, addr);
965 tmp &= ~PORT_RWE;
966 xhci_writel(xhci, tmp, addr);
967 }
968 }
969
970 (void) xhci_readl(xhci, &xhci->op_regs->command);
971
972 bus_state->next_statechange = jiffies + msecs_to_jiffies(5);
973 /* re-enable irqs */
974 temp = xhci_readl(xhci, &xhci->op_regs->command);
975 temp |= CMD_EIE;
976 xhci_writel(xhci, temp, &xhci->op_regs->command);
977 temp = xhci_readl(xhci, &xhci->op_regs->command);
978
979 spin_unlock_irqrestore(&xhci->lock, flags);
980 return 0;
981}
982
983#endif /* CONFIG_PM */
1/*
2 * xHCI host controller driver
3 *
4 * Copyright (C) 2008 Intel Corp.
5 *
6 * Author: Sarah Sharp
7 * Some code borrowed from the Linux EHCI driver.
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
12 *
13 * This program is distributed in the hope that it will be useful, but
14 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
15 * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
16 * for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software Foundation,
20 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21 */
22
23#include <linux/gfp.h>
24#include <asm/unaligned.h>
25
26#include "xhci.h"
27
28#define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
29#define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
30 PORT_RC | PORT_PLC | PORT_PE)
31
32/* usb 1.1 root hub device descriptor */
33static u8 usb_bos_descriptor [] = {
34 USB_DT_BOS_SIZE, /* __u8 bLength, 5 bytes */
35 USB_DT_BOS, /* __u8 bDescriptorType */
36 0x0F, 0x00, /* __le16 wTotalLength, 15 bytes */
37 0x1, /* __u8 bNumDeviceCaps */
38 /* First device capability */
39 USB_DT_USB_SS_CAP_SIZE, /* __u8 bLength, 10 bytes */
40 USB_DT_DEVICE_CAPABILITY, /* Device Capability */
41 USB_SS_CAP_TYPE, /* bDevCapabilityType, SUPERSPEED_USB */
42 0x00, /* bmAttributes, LTM off by default */
43 USB_5GBPS_OPERATION, 0x00, /* wSpeedsSupported, 5Gbps only */
44 0x03, /* bFunctionalitySupport,
45 USB 3.0 speed only */
46 0x00, /* bU1DevExitLat, set later. */
47 0x00, 0x00 /* __le16 bU2DevExitLat, set later. */
48};
49
50
51static void xhci_common_hub_descriptor(struct xhci_hcd *xhci,
52 struct usb_hub_descriptor *desc, int ports)
53{
54 u16 temp;
55
56 desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.9 says 20ms max */
57 desc->bHubContrCurrent = 0;
58
59 desc->bNbrPorts = ports;
60 temp = 0;
61 /* Bits 1:0 - support per-port power switching, or power always on */
62 if (HCC_PPC(xhci->hcc_params))
63 temp |= HUB_CHAR_INDV_PORT_LPSM;
64 else
65 temp |= HUB_CHAR_NO_LPSM;
66 /* Bit 2 - root hubs are not part of a compound device */
67 /* Bits 4:3 - individual port over current protection */
68 temp |= HUB_CHAR_INDV_PORT_OCPM;
69 /* Bits 6:5 - no TTs in root ports */
70 /* Bit 7 - no port indicators */
71 desc->wHubCharacteristics = cpu_to_le16(temp);
72}
73
74/* Fill in the USB 2.0 roothub descriptor */
75static void xhci_usb2_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
76 struct usb_hub_descriptor *desc)
77{
78 int ports;
79 u16 temp;
80 __u8 port_removable[(USB_MAXCHILDREN + 1 + 7) / 8];
81 u32 portsc;
82 unsigned int i;
83
84 ports = xhci->num_usb2_ports;
85
86 xhci_common_hub_descriptor(xhci, desc, ports);
87 desc->bDescriptorType = USB_DT_HUB;
88 temp = 1 + (ports / 8);
89 desc->bDescLength = USB_DT_HUB_NONVAR_SIZE + 2 * temp;
90
91 /* The Device Removable bits are reported on a byte granularity.
92 * If the port doesn't exist within that byte, the bit is set to 0.
93 */
94 memset(port_removable, 0, sizeof(port_removable));
95 for (i = 0; i < ports; i++) {
96 portsc = xhci_readl(xhci, xhci->usb2_ports[i]);
97 /* If a device is removable, PORTSC reports a 0, same as in the
98 * hub descriptor DeviceRemovable bits.
99 */
100 if (portsc & PORT_DEV_REMOVE)
101 /* This math is hairy because bit 0 of DeviceRemovable
102 * is reserved, and bit 1 is for port 1, etc.
103 */
104 port_removable[(i + 1) / 8] |= 1 << ((i + 1) % 8);
105 }
106
107 /* ch11.h defines a hub descriptor that has room for USB_MAXCHILDREN
108 * ports on it. The USB 2.0 specification says that there are two
109 * variable length fields at the end of the hub descriptor:
110 * DeviceRemovable and PortPwrCtrlMask. But since we can have less than
111 * USB_MAXCHILDREN ports, we may need to use the DeviceRemovable array
112 * to set PortPwrCtrlMask bits. PortPwrCtrlMask must always be set to
113 * 0xFF, so we initialize the both arrays (DeviceRemovable and
114 * PortPwrCtrlMask) to 0xFF. Then we set the DeviceRemovable for each
115 * set of ports that actually exist.
116 */
117 memset(desc->u.hs.DeviceRemovable, 0xff,
118 sizeof(desc->u.hs.DeviceRemovable));
119 memset(desc->u.hs.PortPwrCtrlMask, 0xff,
120 sizeof(desc->u.hs.PortPwrCtrlMask));
121
122 for (i = 0; i < (ports + 1 + 7) / 8; i++)
123 memset(&desc->u.hs.DeviceRemovable[i], port_removable[i],
124 sizeof(__u8));
125}
126
127/* Fill in the USB 3.0 roothub descriptor */
128static void xhci_usb3_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
129 struct usb_hub_descriptor *desc)
130{
131 int ports;
132 u16 port_removable;
133 u32 portsc;
134 unsigned int i;
135
136 ports = xhci->num_usb3_ports;
137 xhci_common_hub_descriptor(xhci, desc, ports);
138 desc->bDescriptorType = USB_DT_SS_HUB;
139 desc->bDescLength = USB_DT_SS_HUB_SIZE;
140
141 /* header decode latency should be zero for roothubs,
142 * see section 4.23.5.2.
143 */
144 desc->u.ss.bHubHdrDecLat = 0;
145 desc->u.ss.wHubDelay = 0;
146
147 port_removable = 0;
148 /* bit 0 is reserved, bit 1 is for port 1, etc. */
149 for (i = 0; i < ports; i++) {
150 portsc = xhci_readl(xhci, xhci->usb3_ports[i]);
151 if (portsc & PORT_DEV_REMOVE)
152 port_removable |= 1 << (i + 1);
153 }
154 memset(&desc->u.ss.DeviceRemovable,
155 (__force __u16) cpu_to_le16(port_removable),
156 sizeof(__u16));
157}
158
159static void xhci_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
160 struct usb_hub_descriptor *desc)
161{
162
163 if (hcd->speed == HCD_USB3)
164 xhci_usb3_hub_descriptor(hcd, xhci, desc);
165 else
166 xhci_usb2_hub_descriptor(hcd, xhci, desc);
167
168}
169
170static unsigned int xhci_port_speed(unsigned int port_status)
171{
172 if (DEV_LOWSPEED(port_status))
173 return USB_PORT_STAT_LOW_SPEED;
174 if (DEV_HIGHSPEED(port_status))
175 return USB_PORT_STAT_HIGH_SPEED;
176 /*
177 * FIXME: Yes, we should check for full speed, but the core uses that as
178 * a default in portspeed() in usb/core/hub.c (which is the only place
179 * USB_PORT_STAT_*_SPEED is used).
180 */
181 return 0;
182}
183
184/*
185 * These bits are Read Only (RO) and should be saved and written to the
186 * registers: 0, 3, 10:13, 30
187 * connect status, over-current status, port speed, and device removable.
188 * connect status and port speed are also sticky - meaning they're in
189 * the AUX well and they aren't changed by a hot, warm, or cold reset.
190 */
191#define XHCI_PORT_RO ((1<<0) | (1<<3) | (0xf<<10) | (1<<30))
192/*
193 * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit:
194 * bits 5:8, 9, 14:15, 25:27
195 * link state, port power, port indicator state, "wake on" enable state
196 */
197#define XHCI_PORT_RWS ((0xf<<5) | (1<<9) | (0x3<<14) | (0x7<<25))
198/*
199 * These bits are RW; writing a 1 sets the bit, writing a 0 has no effect:
200 * bit 4 (port reset)
201 */
202#define XHCI_PORT_RW1S ((1<<4))
203/*
204 * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect:
205 * bits 1, 17, 18, 19, 20, 21, 22, 23
206 * port enable/disable, and
207 * change bits: connect, PED, warm port reset changed (reserved zero for USB 2.0 ports),
208 * over-current, reset, link state, and L1 change
209 */
210#define XHCI_PORT_RW1CS ((1<<1) | (0x7f<<17))
211/*
212 * Bit 16 is RW, and writing a '1' to it causes the link state control to be
213 * latched in
214 */
215#define XHCI_PORT_RW ((1<<16))
216/*
217 * These bits are Reserved Zero (RsvdZ) and zero should be written to them:
218 * bits 2, 24, 28:31
219 */
220#define XHCI_PORT_RZ ((1<<2) | (1<<24) | (0xf<<28))
221
222/*
223 * Given a port state, this function returns a value that would result in the
224 * port being in the same state, if the value was written to the port status
225 * control register.
226 * Save Read Only (RO) bits and save read/write bits where
227 * writing a 0 clears the bit and writing a 1 sets the bit (RWS).
228 * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect.
229 */
230u32 xhci_port_state_to_neutral(u32 state)
231{
232 /* Save read-only status and port state */
233 return (state & XHCI_PORT_RO) | (state & XHCI_PORT_RWS);
234}
235
236/*
237 * find slot id based on port number.
238 * @port: The one-based port number from one of the two split roothubs.
239 */
240int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
241 u16 port)
242{
243 int slot_id;
244 int i;
245 enum usb_device_speed speed;
246
247 slot_id = 0;
248 for (i = 0; i < MAX_HC_SLOTS; i++) {
249 if (!xhci->devs[i])
250 continue;
251 speed = xhci->devs[i]->udev->speed;
252 if (((speed == USB_SPEED_SUPER) == (hcd->speed == HCD_USB3))
253 && xhci->devs[i]->fake_port == port) {
254 slot_id = i;
255 break;
256 }
257 }
258
259 return slot_id;
260}
261
262/*
263 * Stop device
264 * It issues stop endpoint command for EP 0 to 30. And wait the last command
265 * to complete.
266 * suspend will set to 1, if suspend bit need to set in command.
267 */
268static int xhci_stop_device(struct xhci_hcd *xhci, int slot_id, int suspend)
269{
270 struct xhci_virt_device *virt_dev;
271 struct xhci_command *cmd;
272 unsigned long flags;
273 int timeleft;
274 int ret;
275 int i;
276
277 ret = 0;
278 virt_dev = xhci->devs[slot_id];
279 cmd = xhci_alloc_command(xhci, false, true, GFP_NOIO);
280 if (!cmd) {
281 xhci_dbg(xhci, "Couldn't allocate command structure.\n");
282 return -ENOMEM;
283 }
284
285 spin_lock_irqsave(&xhci->lock, flags);
286 for (i = LAST_EP_INDEX; i > 0; i--) {
287 if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
288 xhci_queue_stop_endpoint(xhci, slot_id, i, suspend);
289 }
290 cmd->command_trb = xhci->cmd_ring->enqueue;
291 list_add_tail(&cmd->cmd_list, &virt_dev->cmd_list);
292 xhci_queue_stop_endpoint(xhci, slot_id, 0, suspend);
293 xhci_ring_cmd_db(xhci);
294 spin_unlock_irqrestore(&xhci->lock, flags);
295
296 /* Wait for last stop endpoint command to finish */
297 timeleft = wait_for_completion_interruptible_timeout(
298 cmd->completion,
299 USB_CTRL_SET_TIMEOUT);
300 if (timeleft <= 0) {
301 xhci_warn(xhci, "%s while waiting for stop endpoint command\n",
302 timeleft == 0 ? "Timeout" : "Signal");
303 spin_lock_irqsave(&xhci->lock, flags);
304 /* The timeout might have raced with the event ring handler, so
305 * only delete from the list if the item isn't poisoned.
306 */
307 if (cmd->cmd_list.next != LIST_POISON1)
308 list_del(&cmd->cmd_list);
309 spin_unlock_irqrestore(&xhci->lock, flags);
310 ret = -ETIME;
311 goto command_cleanup;
312 }
313
314command_cleanup:
315 xhci_free_command(xhci, cmd);
316 return ret;
317}
318
319/*
320 * Ring device, it rings the all doorbells unconditionally.
321 */
322void xhci_ring_device(struct xhci_hcd *xhci, int slot_id)
323{
324 int i;
325
326 for (i = 0; i < LAST_EP_INDEX + 1; i++)
327 if (xhci->devs[slot_id]->eps[i].ring &&
328 xhci->devs[slot_id]->eps[i].ring->dequeue)
329 xhci_ring_ep_doorbell(xhci, slot_id, i, 0);
330
331 return;
332}
333
334static void xhci_disable_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
335 u16 wIndex, __le32 __iomem *addr, u32 port_status)
336{
337 /* Don't allow the USB core to disable SuperSpeed ports. */
338 if (hcd->speed == HCD_USB3) {
339 xhci_dbg(xhci, "Ignoring request to disable "
340 "SuperSpeed port.\n");
341 return;
342 }
343
344 /* Write 1 to disable the port */
345 xhci_writel(xhci, port_status | PORT_PE, addr);
346 port_status = xhci_readl(xhci, addr);
347 xhci_dbg(xhci, "disable port, actual port %d status = 0x%x\n",
348 wIndex, port_status);
349}
350
351static void xhci_clear_port_change_bit(struct xhci_hcd *xhci, u16 wValue,
352 u16 wIndex, __le32 __iomem *addr, u32 port_status)
353{
354 char *port_change_bit;
355 u32 status;
356
357 switch (wValue) {
358 case USB_PORT_FEAT_C_RESET:
359 status = PORT_RC;
360 port_change_bit = "reset";
361 break;
362 case USB_PORT_FEAT_C_BH_PORT_RESET:
363 status = PORT_WRC;
364 port_change_bit = "warm(BH) reset";
365 break;
366 case USB_PORT_FEAT_C_CONNECTION:
367 status = PORT_CSC;
368 port_change_bit = "connect";
369 break;
370 case USB_PORT_FEAT_C_OVER_CURRENT:
371 status = PORT_OCC;
372 port_change_bit = "over-current";
373 break;
374 case USB_PORT_FEAT_C_ENABLE:
375 status = PORT_PEC;
376 port_change_bit = "enable/disable";
377 break;
378 case USB_PORT_FEAT_C_SUSPEND:
379 status = PORT_PLC;
380 port_change_bit = "suspend/resume";
381 break;
382 case USB_PORT_FEAT_C_PORT_LINK_STATE:
383 status = PORT_PLC;
384 port_change_bit = "link state";
385 break;
386 default:
387 /* Should never happen */
388 return;
389 }
390 /* Change bits are all write 1 to clear */
391 xhci_writel(xhci, port_status | status, addr);
392 port_status = xhci_readl(xhci, addr);
393 xhci_dbg(xhci, "clear port %s change, actual port %d status = 0x%x\n",
394 port_change_bit, wIndex, port_status);
395}
396
397static int xhci_get_ports(struct usb_hcd *hcd, __le32 __iomem ***port_array)
398{
399 int max_ports;
400 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
401
402 if (hcd->speed == HCD_USB3) {
403 max_ports = xhci->num_usb3_ports;
404 *port_array = xhci->usb3_ports;
405 } else {
406 max_ports = xhci->num_usb2_ports;
407 *port_array = xhci->usb2_ports;
408 }
409
410 return max_ports;
411}
412
413void xhci_set_link_state(struct xhci_hcd *xhci, __le32 __iomem **port_array,
414 int port_id, u32 link_state)
415{
416 u32 temp;
417
418 temp = xhci_readl(xhci, port_array[port_id]);
419 temp = xhci_port_state_to_neutral(temp);
420 temp &= ~PORT_PLS_MASK;
421 temp |= PORT_LINK_STROBE | link_state;
422 xhci_writel(xhci, temp, port_array[port_id]);
423}
424
425void xhci_set_remote_wake_mask(struct xhci_hcd *xhci,
426 __le32 __iomem **port_array, int port_id, u16 wake_mask)
427{
428 u32 temp;
429
430 temp = xhci_readl(xhci, port_array[port_id]);
431 temp = xhci_port_state_to_neutral(temp);
432
433 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_CONNECT)
434 temp |= PORT_WKCONN_E;
435 else
436 temp &= ~PORT_WKCONN_E;
437
438 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT)
439 temp |= PORT_WKDISC_E;
440 else
441 temp &= ~PORT_WKDISC_E;
442
443 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT)
444 temp |= PORT_WKOC_E;
445 else
446 temp &= ~PORT_WKOC_E;
447
448 xhci_writel(xhci, temp, port_array[port_id]);
449}
450
451/* Test and clear port RWC bit */
452void xhci_test_and_clear_bit(struct xhci_hcd *xhci, __le32 __iomem **port_array,
453 int port_id, u32 port_bit)
454{
455 u32 temp;
456
457 temp = xhci_readl(xhci, port_array[port_id]);
458 if (temp & port_bit) {
459 temp = xhci_port_state_to_neutral(temp);
460 temp |= port_bit;
461 xhci_writel(xhci, temp, port_array[port_id]);
462 }
463}
464
465/* Updates Link Status for super Speed port */
466static void xhci_hub_report_link_state(u32 *status, u32 status_reg)
467{
468 u32 pls = status_reg & PORT_PLS_MASK;
469
470 /* resume state is a xHCI internal state.
471 * Do not report it to usb core.
472 */
473 if (pls == XDEV_RESUME)
474 return;
475
476 /* When the CAS bit is set then warm reset
477 * should be performed on port
478 */
479 if (status_reg & PORT_CAS) {
480 /* The CAS bit can be set while the port is
481 * in any link state.
482 * Only roothubs have CAS bit, so we
483 * pretend to be in compliance mode
484 * unless we're already in compliance
485 * or the inactive state.
486 */
487 if (pls != USB_SS_PORT_LS_COMP_MOD &&
488 pls != USB_SS_PORT_LS_SS_INACTIVE) {
489 pls = USB_SS_PORT_LS_COMP_MOD;
490 }
491 /* Return also connection bit -
492 * hub state machine resets port
493 * when this bit is set.
494 */
495 pls |= USB_PORT_STAT_CONNECTION;
496 } else {
497 /*
498 * If CAS bit isn't set but the Port is already at
499 * Compliance Mode, fake a connection so the USB core
500 * notices the Compliance state and resets the port.
501 * This resolves an issue generated by the SN65LVPE502CP
502 * in which sometimes the port enters compliance mode
503 * caused by a delay on the host-device negotiation.
504 */
505 if (pls == USB_SS_PORT_LS_COMP_MOD)
506 pls |= USB_PORT_STAT_CONNECTION;
507 }
508
509 /* update status field */
510 *status |= pls;
511}
512
513/*
514 * Function for Compliance Mode Quirk.
515 *
516 * This Function verifies if all xhc USB3 ports have entered U0, if so,
517 * the compliance mode timer is deleted. A port won't enter
518 * compliance mode if it has previously entered U0.
519 */
520void xhci_del_comp_mod_timer(struct xhci_hcd *xhci, u32 status, u16 wIndex)
521{
522 u32 all_ports_seen_u0 = ((1 << xhci->num_usb3_ports)-1);
523 bool port_in_u0 = ((status & PORT_PLS_MASK) == XDEV_U0);
524
525 if (!(xhci->quirks & XHCI_COMP_MODE_QUIRK))
526 return;
527
528 if ((xhci->port_status_u0 != all_ports_seen_u0) && port_in_u0) {
529 xhci->port_status_u0 |= 1 << wIndex;
530 if (xhci->port_status_u0 == all_ports_seen_u0) {
531 del_timer_sync(&xhci->comp_mode_recovery_timer);
532 xhci_dbg(xhci, "All USB3 ports have entered U0 already!\n");
533 xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted.\n");
534 }
535 }
536}
537
538int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
539 u16 wIndex, char *buf, u16 wLength)
540{
541 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
542 int max_ports;
543 unsigned long flags;
544 u32 temp, status;
545 int retval = 0;
546 __le32 __iomem **port_array;
547 int slot_id;
548 struct xhci_bus_state *bus_state;
549 u16 link_state = 0;
550 u16 wake_mask = 0;
551 u16 timeout = 0;
552
553 max_ports = xhci_get_ports(hcd, &port_array);
554 bus_state = &xhci->bus_state[hcd_index(hcd)];
555
556 spin_lock_irqsave(&xhci->lock, flags);
557 switch (typeReq) {
558 case GetHubStatus:
559 /* No power source, over-current reported per port */
560 memset(buf, 0, 4);
561 break;
562 case GetHubDescriptor:
563 /* Check to make sure userspace is asking for the USB 3.0 hub
564 * descriptor for the USB 3.0 roothub. If not, we stall the
565 * endpoint, like external hubs do.
566 */
567 if (hcd->speed == HCD_USB3 &&
568 (wLength < USB_DT_SS_HUB_SIZE ||
569 wValue != (USB_DT_SS_HUB << 8))) {
570 xhci_dbg(xhci, "Wrong hub descriptor type for "
571 "USB 3.0 roothub.\n");
572 goto error;
573 }
574 xhci_hub_descriptor(hcd, xhci,
575 (struct usb_hub_descriptor *) buf);
576 break;
577 case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
578 if ((wValue & 0xff00) != (USB_DT_BOS << 8))
579 goto error;
580
581 if (hcd->speed != HCD_USB3)
582 goto error;
583
584 memcpy(buf, &usb_bos_descriptor,
585 USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE);
586 temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
587 buf[12] = HCS_U1_LATENCY(temp);
588 put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
589
590 spin_unlock_irqrestore(&xhci->lock, flags);
591 return USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
592 case GetPortStatus:
593 if (!wIndex || wIndex > max_ports)
594 goto error;
595 wIndex--;
596 status = 0;
597 temp = xhci_readl(xhci, port_array[wIndex]);
598 if (temp == 0xffffffff) {
599 retval = -ENODEV;
600 break;
601 }
602 xhci_dbg(xhci, "get port status, actual port %d status = 0x%x\n", wIndex, temp);
603
604 /* wPortChange bits */
605 if (temp & PORT_CSC)
606 status |= USB_PORT_STAT_C_CONNECTION << 16;
607 if (temp & PORT_PEC)
608 status |= USB_PORT_STAT_C_ENABLE << 16;
609 if ((temp & PORT_OCC))
610 status |= USB_PORT_STAT_C_OVERCURRENT << 16;
611 if ((temp & PORT_RC))
612 status |= USB_PORT_STAT_C_RESET << 16;
613 /* USB3.0 only */
614 if (hcd->speed == HCD_USB3) {
615 if ((temp & PORT_PLC))
616 status |= USB_PORT_STAT_C_LINK_STATE << 16;
617 if ((temp & PORT_WRC))
618 status |= USB_PORT_STAT_C_BH_RESET << 16;
619 }
620
621 if (hcd->speed != HCD_USB3) {
622 if ((temp & PORT_PLS_MASK) == XDEV_U3
623 && (temp & PORT_POWER))
624 status |= USB_PORT_STAT_SUSPEND;
625 }
626 if ((temp & PORT_PLS_MASK) == XDEV_RESUME &&
627 !DEV_SUPERSPEED(temp)) {
628 if ((temp & PORT_RESET) || !(temp & PORT_PE))
629 goto error;
630 if (time_after_eq(jiffies,
631 bus_state->resume_done[wIndex])) {
632 xhci_dbg(xhci, "Resume USB2 port %d\n",
633 wIndex + 1);
634 bus_state->resume_done[wIndex] = 0;
635 clear_bit(wIndex, &bus_state->resuming_ports);
636 xhci_set_link_state(xhci, port_array, wIndex,
637 XDEV_U0);
638 xhci_dbg(xhci, "set port %d resume\n",
639 wIndex + 1);
640 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
641 wIndex + 1);
642 if (!slot_id) {
643 xhci_dbg(xhci, "slot_id is zero\n");
644 goto error;
645 }
646 xhci_ring_device(xhci, slot_id);
647 bus_state->port_c_suspend |= 1 << wIndex;
648 bus_state->suspended_ports &= ~(1 << wIndex);
649 } else {
650 /*
651 * The resume has been signaling for less than
652 * 20ms. Report the port status as SUSPEND,
653 * let the usbcore check port status again
654 * and clear resume signaling later.
655 */
656 status |= USB_PORT_STAT_SUSPEND;
657 }
658 }
659 if ((temp & PORT_PLS_MASK) == XDEV_U0
660 && (temp & PORT_POWER)
661 && (bus_state->suspended_ports & (1 << wIndex))) {
662 bus_state->suspended_ports &= ~(1 << wIndex);
663 if (hcd->speed != HCD_USB3)
664 bus_state->port_c_suspend |= 1 << wIndex;
665 }
666 if (temp & PORT_CONNECT) {
667 status |= USB_PORT_STAT_CONNECTION;
668 status |= xhci_port_speed(temp);
669 }
670 if (temp & PORT_PE)
671 status |= USB_PORT_STAT_ENABLE;
672 if (temp & PORT_OC)
673 status |= USB_PORT_STAT_OVERCURRENT;
674 if (temp & PORT_RESET)
675 status |= USB_PORT_STAT_RESET;
676 if (temp & PORT_POWER) {
677 if (hcd->speed == HCD_USB3)
678 status |= USB_SS_PORT_STAT_POWER;
679 else
680 status |= USB_PORT_STAT_POWER;
681 }
682 /* Update Port Link State for super speed ports*/
683 if (hcd->speed == HCD_USB3) {
684 xhci_hub_report_link_state(&status, temp);
685 /*
686 * Verify if all USB3 Ports Have entered U0 already.
687 * Delete Compliance Mode Timer if so.
688 */
689 xhci_del_comp_mod_timer(xhci, temp, wIndex);
690 }
691 if (bus_state->port_c_suspend & (1 << wIndex))
692 status |= 1 << USB_PORT_FEAT_C_SUSPEND;
693 xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
694 put_unaligned(cpu_to_le32(status), (__le32 *) buf);
695 break;
696 case SetPortFeature:
697 if (wValue == USB_PORT_FEAT_LINK_STATE)
698 link_state = (wIndex & 0xff00) >> 3;
699 if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK)
700 wake_mask = wIndex & 0xff00;
701 /* The MSB of wIndex is the U1/U2 timeout */
702 timeout = (wIndex & 0xff00) >> 8;
703 wIndex &= 0xff;
704 if (!wIndex || wIndex > max_ports)
705 goto error;
706 wIndex--;
707 temp = xhci_readl(xhci, port_array[wIndex]);
708 if (temp == 0xffffffff) {
709 retval = -ENODEV;
710 break;
711 }
712 temp = xhci_port_state_to_neutral(temp);
713 /* FIXME: What new port features do we need to support? */
714 switch (wValue) {
715 case USB_PORT_FEAT_SUSPEND:
716 temp = xhci_readl(xhci, port_array[wIndex]);
717 if ((temp & PORT_PLS_MASK) != XDEV_U0) {
718 /* Resume the port to U0 first */
719 xhci_set_link_state(xhci, port_array, wIndex,
720 XDEV_U0);
721 spin_unlock_irqrestore(&xhci->lock, flags);
722 msleep(10);
723 spin_lock_irqsave(&xhci->lock, flags);
724 }
725 /* In spec software should not attempt to suspend
726 * a port unless the port reports that it is in the
727 * enabled (PED = ‘1’,PLS < ‘3’) state.
728 */
729 temp = xhci_readl(xhci, port_array[wIndex]);
730 if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
731 || (temp & PORT_PLS_MASK) >= XDEV_U3) {
732 xhci_warn(xhci, "USB core suspending device "
733 "not in U0/U1/U2.\n");
734 goto error;
735 }
736
737 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
738 wIndex + 1);
739 if (!slot_id) {
740 xhci_warn(xhci, "slot_id is zero\n");
741 goto error;
742 }
743 /* unlock to execute stop endpoint commands */
744 spin_unlock_irqrestore(&xhci->lock, flags);
745 xhci_stop_device(xhci, slot_id, 1);
746 spin_lock_irqsave(&xhci->lock, flags);
747
748 xhci_set_link_state(xhci, port_array, wIndex, XDEV_U3);
749
750 spin_unlock_irqrestore(&xhci->lock, flags);
751 msleep(10); /* wait device to enter */
752 spin_lock_irqsave(&xhci->lock, flags);
753
754 temp = xhci_readl(xhci, port_array[wIndex]);
755 bus_state->suspended_ports |= 1 << wIndex;
756 break;
757 case USB_PORT_FEAT_LINK_STATE:
758 temp = xhci_readl(xhci, port_array[wIndex]);
759 /* Software should not attempt to set
760 * port link state above '5' (Rx.Detect) and the port
761 * must be enabled.
762 */
763 if ((temp & PORT_PE) == 0 ||
764 (link_state > USB_SS_PORT_LS_RX_DETECT)) {
765 xhci_warn(xhci, "Cannot set link state.\n");
766 goto error;
767 }
768
769 if (link_state == USB_SS_PORT_LS_U3) {
770 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
771 wIndex + 1);
772 if (slot_id) {
773 /* unlock to execute stop endpoint
774 * commands */
775 spin_unlock_irqrestore(&xhci->lock,
776 flags);
777 xhci_stop_device(xhci, slot_id, 1);
778 spin_lock_irqsave(&xhci->lock, flags);
779 }
780 }
781
782 xhci_set_link_state(xhci, port_array, wIndex,
783 link_state);
784
785 spin_unlock_irqrestore(&xhci->lock, flags);
786 msleep(20); /* wait device to enter */
787 spin_lock_irqsave(&xhci->lock, flags);
788
789 temp = xhci_readl(xhci, port_array[wIndex]);
790 if (link_state == USB_SS_PORT_LS_U3)
791 bus_state->suspended_ports |= 1 << wIndex;
792 break;
793 case USB_PORT_FEAT_POWER:
794 /*
795 * Turn on ports, even if there isn't per-port switching.
796 * HC will report connect events even before this is set.
797 * However, khubd will ignore the roothub events until
798 * the roothub is registered.
799 */
800 xhci_writel(xhci, temp | PORT_POWER,
801 port_array[wIndex]);
802
803 temp = xhci_readl(xhci, port_array[wIndex]);
804 xhci_dbg(xhci, "set port power, actual port %d status = 0x%x\n", wIndex, temp);
805 break;
806 case USB_PORT_FEAT_RESET:
807 temp = (temp | PORT_RESET);
808 xhci_writel(xhci, temp, port_array[wIndex]);
809
810 temp = xhci_readl(xhci, port_array[wIndex]);
811 xhci_dbg(xhci, "set port reset, actual port %d status = 0x%x\n", wIndex, temp);
812 break;
813 case USB_PORT_FEAT_REMOTE_WAKE_MASK:
814 xhci_set_remote_wake_mask(xhci, port_array,
815 wIndex, wake_mask);
816 temp = xhci_readl(xhci, port_array[wIndex]);
817 xhci_dbg(xhci, "set port remote wake mask, "
818 "actual port %d status = 0x%x\n",
819 wIndex, temp);
820 break;
821 case USB_PORT_FEAT_BH_PORT_RESET:
822 temp |= PORT_WR;
823 xhci_writel(xhci, temp, port_array[wIndex]);
824
825 temp = xhci_readl(xhci, port_array[wIndex]);
826 break;
827 case USB_PORT_FEAT_U1_TIMEOUT:
828 if (hcd->speed != HCD_USB3)
829 goto error;
830 temp = xhci_readl(xhci, port_array[wIndex] + 1);
831 temp &= ~PORT_U1_TIMEOUT_MASK;
832 temp |= PORT_U1_TIMEOUT(timeout);
833 xhci_writel(xhci, temp, port_array[wIndex] + 1);
834 break;
835 case USB_PORT_FEAT_U2_TIMEOUT:
836 if (hcd->speed != HCD_USB3)
837 goto error;
838 temp = xhci_readl(xhci, port_array[wIndex] + 1);
839 temp &= ~PORT_U2_TIMEOUT_MASK;
840 temp |= PORT_U2_TIMEOUT(timeout);
841 xhci_writel(xhci, temp, port_array[wIndex] + 1);
842 break;
843 default:
844 goto error;
845 }
846 /* unblock any posted writes */
847 temp = xhci_readl(xhci, port_array[wIndex]);
848 break;
849 case ClearPortFeature:
850 if (!wIndex || wIndex > max_ports)
851 goto error;
852 wIndex--;
853 temp = xhci_readl(xhci, port_array[wIndex]);
854 if (temp == 0xffffffff) {
855 retval = -ENODEV;
856 break;
857 }
858 /* FIXME: What new port features do we need to support? */
859 temp = xhci_port_state_to_neutral(temp);
860 switch (wValue) {
861 case USB_PORT_FEAT_SUSPEND:
862 temp = xhci_readl(xhci, port_array[wIndex]);
863 xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
864 xhci_dbg(xhci, "PORTSC %04x\n", temp);
865 if (temp & PORT_RESET)
866 goto error;
867 if ((temp & PORT_PLS_MASK) == XDEV_U3) {
868 if ((temp & PORT_PE) == 0)
869 goto error;
870
871 xhci_set_link_state(xhci, port_array, wIndex,
872 XDEV_RESUME);
873 spin_unlock_irqrestore(&xhci->lock, flags);
874 msleep(20);
875 spin_lock_irqsave(&xhci->lock, flags);
876 xhci_set_link_state(xhci, port_array, wIndex,
877 XDEV_U0);
878 }
879 bus_state->port_c_suspend |= 1 << wIndex;
880
881 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
882 wIndex + 1);
883 if (!slot_id) {
884 xhci_dbg(xhci, "slot_id is zero\n");
885 goto error;
886 }
887 xhci_ring_device(xhci, slot_id);
888 break;
889 case USB_PORT_FEAT_C_SUSPEND:
890 bus_state->port_c_suspend &= ~(1 << wIndex);
891 case USB_PORT_FEAT_C_RESET:
892 case USB_PORT_FEAT_C_BH_PORT_RESET:
893 case USB_PORT_FEAT_C_CONNECTION:
894 case USB_PORT_FEAT_C_OVER_CURRENT:
895 case USB_PORT_FEAT_C_ENABLE:
896 case USB_PORT_FEAT_C_PORT_LINK_STATE:
897 xhci_clear_port_change_bit(xhci, wValue, wIndex,
898 port_array[wIndex], temp);
899 break;
900 case USB_PORT_FEAT_ENABLE:
901 xhci_disable_port(hcd, xhci, wIndex,
902 port_array[wIndex], temp);
903 break;
904 default:
905 goto error;
906 }
907 break;
908 default:
909error:
910 /* "stall" on error */
911 retval = -EPIPE;
912 }
913 spin_unlock_irqrestore(&xhci->lock, flags);
914 return retval;
915}
916
917/*
918 * Returns 0 if the status hasn't changed, or the number of bytes in buf.
919 * Ports are 0-indexed from the HCD point of view,
920 * and 1-indexed from the USB core pointer of view.
921 *
922 * Note that the status change bits will be cleared as soon as a port status
923 * change event is generated, so we use the saved status from that event.
924 */
925int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
926{
927 unsigned long flags;
928 u32 temp, status;
929 u32 mask;
930 int i, retval;
931 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
932 int max_ports;
933 __le32 __iomem **port_array;
934 struct xhci_bus_state *bus_state;
935
936 max_ports = xhci_get_ports(hcd, &port_array);
937 bus_state = &xhci->bus_state[hcd_index(hcd)];
938
939 /* Initial status is no changes */
940 retval = (max_ports + 8) / 8;
941 memset(buf, 0, retval);
942
943 /*
944 * Inform the usbcore about resume-in-progress by returning
945 * a non-zero value even if there are no status changes.
946 */
947 status = bus_state->resuming_ports;
948
949 mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC;
950
951 spin_lock_irqsave(&xhci->lock, flags);
952 /* For each port, did anything change? If so, set that bit in buf. */
953 for (i = 0; i < max_ports; i++) {
954 temp = xhci_readl(xhci, port_array[i]);
955 if (temp == 0xffffffff) {
956 retval = -ENODEV;
957 break;
958 }
959 if ((temp & mask) != 0 ||
960 (bus_state->port_c_suspend & 1 << i) ||
961 (bus_state->resume_done[i] && time_after_eq(
962 jiffies, bus_state->resume_done[i]))) {
963 buf[(i + 1) / 8] |= 1 << (i + 1) % 8;
964 status = 1;
965 }
966 }
967 spin_unlock_irqrestore(&xhci->lock, flags);
968 return status ? retval : 0;
969}
970
971#ifdef CONFIG_PM
972
973int xhci_bus_suspend(struct usb_hcd *hcd)
974{
975 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
976 int max_ports, port_index;
977 __le32 __iomem **port_array;
978 struct xhci_bus_state *bus_state;
979 unsigned long flags;
980
981 max_ports = xhci_get_ports(hcd, &port_array);
982 bus_state = &xhci->bus_state[hcd_index(hcd)];
983
984 spin_lock_irqsave(&xhci->lock, flags);
985
986 if (hcd->self.root_hub->do_remote_wakeup) {
987 if (bus_state->resuming_ports) {
988 spin_unlock_irqrestore(&xhci->lock, flags);
989 xhci_dbg(xhci, "suspend failed because "
990 "a port is resuming\n");
991 return -EBUSY;
992 }
993 }
994
995 port_index = max_ports;
996 bus_state->bus_suspended = 0;
997 while (port_index--) {
998 /* suspend the port if the port is not suspended */
999 u32 t1, t2;
1000 int slot_id;
1001
1002 t1 = xhci_readl(xhci, port_array[port_index]);
1003 t2 = xhci_port_state_to_neutral(t1);
1004
1005 if ((t1 & PORT_PE) && !(t1 & PORT_PLS_MASK)) {
1006 xhci_dbg(xhci, "port %d not suspended\n", port_index);
1007 slot_id = xhci_find_slot_id_by_port(hcd, xhci,
1008 port_index + 1);
1009 if (slot_id) {
1010 spin_unlock_irqrestore(&xhci->lock, flags);
1011 xhci_stop_device(xhci, slot_id, 1);
1012 spin_lock_irqsave(&xhci->lock, flags);
1013 }
1014 t2 &= ~PORT_PLS_MASK;
1015 t2 |= PORT_LINK_STROBE | XDEV_U3;
1016 set_bit(port_index, &bus_state->bus_suspended);
1017 }
1018 /* USB core sets remote wake mask for USB 3.0 hubs,
1019 * including the USB 3.0 roothub, but only if CONFIG_USB_SUSPEND
1020 * is enabled, so also enable remote wake here.
1021 */
1022 if (hcd->self.root_hub->do_remote_wakeup) {
1023 if (t1 & PORT_CONNECT) {
1024 t2 |= PORT_WKOC_E | PORT_WKDISC_E;
1025 t2 &= ~PORT_WKCONN_E;
1026 } else {
1027 t2 |= PORT_WKOC_E | PORT_WKCONN_E;
1028 t2 &= ~PORT_WKDISC_E;
1029 }
1030 } else
1031 t2 &= ~PORT_WAKE_BITS;
1032
1033 t1 = xhci_port_state_to_neutral(t1);
1034 if (t1 != t2)
1035 xhci_writel(xhci, t2, port_array[port_index]);
1036
1037 if (hcd->speed != HCD_USB3) {
1038 /* enable remote wake up for USB 2.0 */
1039 __le32 __iomem *addr;
1040 u32 tmp;
1041
1042 /* Add one to the port status register address to get
1043 * the port power control register address.
1044 */
1045 addr = port_array[port_index] + 1;
1046 tmp = xhci_readl(xhci, addr);
1047 tmp |= PORT_RWE;
1048 xhci_writel(xhci, tmp, addr);
1049 }
1050 }
1051 hcd->state = HC_STATE_SUSPENDED;
1052 bus_state->next_statechange = jiffies + msecs_to_jiffies(10);
1053 spin_unlock_irqrestore(&xhci->lock, flags);
1054 return 0;
1055}
1056
1057int xhci_bus_resume(struct usb_hcd *hcd)
1058{
1059 struct xhci_hcd *xhci = hcd_to_xhci(hcd);
1060 int max_ports, port_index;
1061 __le32 __iomem **port_array;
1062 struct xhci_bus_state *bus_state;
1063 u32 temp;
1064 unsigned long flags;
1065
1066 max_ports = xhci_get_ports(hcd, &port_array);
1067 bus_state = &xhci->bus_state[hcd_index(hcd)];
1068
1069 if (time_before(jiffies, bus_state->next_statechange))
1070 msleep(5);
1071
1072 spin_lock_irqsave(&xhci->lock, flags);
1073 if (!HCD_HW_ACCESSIBLE(hcd)) {
1074 spin_unlock_irqrestore(&xhci->lock, flags);
1075 return -ESHUTDOWN;
1076 }
1077
1078 /* delay the irqs */
1079 temp = xhci_readl(xhci, &xhci->op_regs->command);
1080 temp &= ~CMD_EIE;
1081 xhci_writel(xhci, temp, &xhci->op_regs->command);
1082
1083 port_index = max_ports;
1084 while (port_index--) {
1085 /* Check whether need resume ports. If needed
1086 resume port and disable remote wakeup */
1087 u32 temp;
1088 int slot_id;
1089
1090 temp = xhci_readl(xhci, port_array[port_index]);
1091 if (DEV_SUPERSPEED(temp))
1092 temp &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
1093 else
1094 temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
1095 if (test_bit(port_index, &bus_state->bus_suspended) &&
1096 (temp & PORT_PLS_MASK)) {
1097 if (DEV_SUPERSPEED(temp)) {
1098 xhci_set_link_state(xhci, port_array,
1099 port_index, XDEV_U0);
1100 } else {
1101 xhci_set_link_state(xhci, port_array,
1102 port_index, XDEV_RESUME);
1103
1104 spin_unlock_irqrestore(&xhci->lock, flags);
1105 msleep(20);
1106 spin_lock_irqsave(&xhci->lock, flags);
1107
1108 xhci_set_link_state(xhci, port_array,
1109 port_index, XDEV_U0);
1110 }
1111 /* wait for the port to enter U0 and report port link
1112 * state change.
1113 */
1114 spin_unlock_irqrestore(&xhci->lock, flags);
1115 msleep(20);
1116 spin_lock_irqsave(&xhci->lock, flags);
1117
1118 /* Clear PLC */
1119 xhci_test_and_clear_bit(xhci, port_array, port_index,
1120 PORT_PLC);
1121
1122 slot_id = xhci_find_slot_id_by_port(hcd,
1123 xhci, port_index + 1);
1124 if (slot_id)
1125 xhci_ring_device(xhci, slot_id);
1126 } else
1127 xhci_writel(xhci, temp, port_array[port_index]);
1128
1129 if (hcd->speed != HCD_USB3) {
1130 /* disable remote wake up for USB 2.0 */
1131 __le32 __iomem *addr;
1132 u32 tmp;
1133
1134 /* Add one to the port status register address to get
1135 * the port power control register address.
1136 */
1137 addr = port_array[port_index] + 1;
1138 tmp = xhci_readl(xhci, addr);
1139 tmp &= ~PORT_RWE;
1140 xhci_writel(xhci, tmp, addr);
1141 }
1142 }
1143
1144 (void) xhci_readl(xhci, &xhci->op_regs->command);
1145
1146 bus_state->next_statechange = jiffies + msecs_to_jiffies(5);
1147 /* re-enable irqs */
1148 temp = xhci_readl(xhci, &xhci->op_regs->command);
1149 temp |= CMD_EIE;
1150 xhci_writel(xhci, temp, &xhci->op_regs->command);
1151 temp = xhci_readl(xhci, &xhci->op_regs->command);
1152
1153 spin_unlock_irqrestore(&xhci->lock, flags);
1154 return 0;
1155}
1156
1157#endif /* CONFIG_PM */