Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * This file contains code to reset and initialize USB host controllers.
4 * Some of it includes work-arounds for PCI hardware and BIOS quirks.
5 * It may need to run early during booting -- before USB would normally
6 * initialize -- to ensure that Linux doesn't use any legacy modes.
7 *
8 * Copyright (c) 1999 Martin Mares <mj@ucw.cz>
9 * (and others)
10 */
11
12#include <linux/types.h>
13#include <linux/kernel.h>
14#include <linux/pci.h>
15#include <linux/delay.h>
16#include <linux/export.h>
17#include <linux/acpi.h>
18#include <linux/dmi.h>
19#include <linux/of.h>
20#include <linux/iopoll.h>
21
22#include "pci-quirks.h"
23#include "xhci-ext-caps.h"
24
25
26#define UHCI_USBLEGSUP 0xc0 /* legacy support */
27#define UHCI_USBCMD 0 /* command register */
28#define UHCI_USBINTR 4 /* interrupt register */
29#define UHCI_USBLEGSUP_RWC 0x8f00 /* the R/WC bits */
30#define UHCI_USBLEGSUP_RO 0x5040 /* R/O and reserved bits */
31#define UHCI_USBCMD_RUN 0x0001 /* RUN/STOP bit */
32#define UHCI_USBCMD_HCRESET 0x0002 /* Host Controller reset */
33#define UHCI_USBCMD_EGSM 0x0008 /* Global Suspend Mode */
34#define UHCI_USBCMD_CONFIGURE 0x0040 /* Config Flag */
35#define UHCI_USBINTR_RESUME 0x0002 /* Resume interrupt enable */
36
37#define OHCI_CONTROL 0x04
38#define OHCI_CMDSTATUS 0x08
39#define OHCI_INTRSTATUS 0x0c
40#define OHCI_INTRENABLE 0x10
41#define OHCI_INTRDISABLE 0x14
42#define OHCI_FMINTERVAL 0x34
43#define OHCI_HCFS (3 << 6) /* hc functional state */
44#define OHCI_HCR (1 << 0) /* host controller reset */
45#define OHCI_OCR (1 << 3) /* ownership change request */
46#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */
47#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
48#define OHCI_INTR_OC (1 << 30) /* ownership change */
49
50#define EHCI_HCC_PARAMS 0x08 /* extended capabilities */
51#define EHCI_USBCMD 0 /* command register */
52#define EHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
53#define EHCI_USBSTS 4 /* status register */
54#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
55#define EHCI_USBINTR 8 /* interrupt register */
56#define EHCI_CONFIGFLAG 0x40 /* configured flag register */
57#define EHCI_USBLEGSUP 0 /* legacy support register */
58#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
59#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
60#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
61#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI on ownership change */
62
63/* ASMEDIA quirk use */
64#define ASMT_DATA_WRITE0_REG 0xF8
65#define ASMT_DATA_WRITE1_REG 0xFC
66#define ASMT_CONTROL_REG 0xE0
67#define ASMT_CONTROL_WRITE_BIT 0x02
68#define ASMT_WRITEREG_CMD 0x10423
69#define ASMT_FLOWCTL_ADDR 0xFA30
70#define ASMT_FLOWCTL_DATA 0xBA
71#define ASMT_PSEUDO_DATA 0
72
73/* Intel quirk use */
74#define USB_INTEL_XUSB2PR 0xD0
75#define USB_INTEL_USB2PRM 0xD4
76#define USB_INTEL_USB3_PSSEN 0xD8
77#define USB_INTEL_USB3PRM 0xDC
78
79#ifdef CONFIG_USB_PCI_AMD
80/* AMD quirk use */
81#define AB_REG_BAR_LOW 0xe0
82#define AB_REG_BAR_HIGH 0xe1
83#define AB_REG_BAR_SB700 0xf0
84#define AB_INDX(addr) ((addr) + 0x00)
85#define AB_DATA(addr) ((addr) + 0x04)
86#define AX_INDXC 0x30
87#define AX_DATAC 0x34
88
89#define PT_ADDR_INDX 0xE8
90#define PT_READ_INDX 0xE4
91#define PT_SIG_1_ADDR 0xA520
92#define PT_SIG_2_ADDR 0xA521
93#define PT_SIG_3_ADDR 0xA522
94#define PT_SIG_4_ADDR 0xA523
95#define PT_SIG_1_DATA 0x78
96#define PT_SIG_2_DATA 0x56
97#define PT_SIG_3_DATA 0x34
98#define PT_SIG_4_DATA 0x12
99#define PT4_P1_REG 0xB521
100#define PT4_P2_REG 0xB522
101#define PT2_P1_REG 0xD520
102#define PT2_P2_REG 0xD521
103#define PT1_P1_REG 0xD522
104#define PT1_P2_REG 0xD523
105
106#define NB_PCIE_INDX_ADDR 0xe0
107#define NB_PCIE_INDX_DATA 0xe4
108#define PCIE_P_CNTL 0x10040
109#define BIF_NB 0x10002
110#define NB_PIF0_PWRDOWN_0 0x01100012
111#define NB_PIF0_PWRDOWN_1 0x01100013
112
113/*
114 * amd_chipset_gen values represent AMD different chipset generations
115 */
116enum amd_chipset_gen {
117 NOT_AMD_CHIPSET = 0,
118 AMD_CHIPSET_SB600,
119 AMD_CHIPSET_SB700,
120 AMD_CHIPSET_SB800,
121 AMD_CHIPSET_HUDSON2,
122 AMD_CHIPSET_BOLTON,
123 AMD_CHIPSET_YANGTZE,
124 AMD_CHIPSET_TAISHAN,
125 AMD_CHIPSET_UNKNOWN,
126};
127
128struct amd_chipset_type {
129 enum amd_chipset_gen gen;
130 u8 rev;
131};
132
133static struct amd_chipset_info {
134 struct pci_dev *nb_dev;
135 struct pci_dev *smbus_dev;
136 int nb_type;
137 struct amd_chipset_type sb_type;
138 int isoc_reqs;
139 int probe_count;
140 bool need_pll_quirk;
141} amd_chipset;
142
143static DEFINE_SPINLOCK(amd_lock);
144
145/*
146 * amd_chipset_sb_type_init - initialize amd chipset southbridge type
147 *
148 * AMD FCH/SB generation and revision is identified by SMBus controller
149 * vendor, device and revision IDs.
150 *
151 * Returns: 1 if it is an AMD chipset, 0 otherwise.
152 */
153static int amd_chipset_sb_type_init(struct amd_chipset_info *pinfo)
154{
155 u8 rev = 0;
156 pinfo->sb_type.gen = AMD_CHIPSET_UNKNOWN;
157
158 pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI,
159 PCI_DEVICE_ID_ATI_SBX00_SMBUS, NULL);
160 if (pinfo->smbus_dev) {
161 rev = pinfo->smbus_dev->revision;
162 if (rev >= 0x10 && rev <= 0x1f)
163 pinfo->sb_type.gen = AMD_CHIPSET_SB600;
164 else if (rev >= 0x30 && rev <= 0x3f)
165 pinfo->sb_type.gen = AMD_CHIPSET_SB700;
166 else if (rev >= 0x40 && rev <= 0x4f)
167 pinfo->sb_type.gen = AMD_CHIPSET_SB800;
168 } else {
169 pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
170 PCI_DEVICE_ID_AMD_HUDSON2_SMBUS, NULL);
171
172 if (pinfo->smbus_dev) {
173 rev = pinfo->smbus_dev->revision;
174 if (rev >= 0x11 && rev <= 0x14)
175 pinfo->sb_type.gen = AMD_CHIPSET_HUDSON2;
176 else if (rev >= 0x15 && rev <= 0x18)
177 pinfo->sb_type.gen = AMD_CHIPSET_BOLTON;
178 else if (rev >= 0x39 && rev <= 0x3a)
179 pinfo->sb_type.gen = AMD_CHIPSET_YANGTZE;
180 } else {
181 pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
182 0x145c, NULL);
183 if (pinfo->smbus_dev) {
184 rev = pinfo->smbus_dev->revision;
185 pinfo->sb_type.gen = AMD_CHIPSET_TAISHAN;
186 } else {
187 pinfo->sb_type.gen = NOT_AMD_CHIPSET;
188 return 0;
189 }
190 }
191 }
192 pinfo->sb_type.rev = rev;
193 return 1;
194}
195
196void sb800_prefetch(struct device *dev, int on)
197{
198 u16 misc;
199 struct pci_dev *pdev = to_pci_dev(dev);
200
201 pci_read_config_word(pdev, 0x50, &misc);
202 if (on == 0)
203 pci_write_config_word(pdev, 0x50, misc & 0xfcff);
204 else
205 pci_write_config_word(pdev, 0x50, misc | 0x0300);
206}
207EXPORT_SYMBOL_GPL(sb800_prefetch);
208
209static void usb_amd_find_chipset_info(void)
210{
211 unsigned long flags;
212 struct amd_chipset_info info = { };
213
214 spin_lock_irqsave(&amd_lock, flags);
215
216 /* probe only once */
217 if (amd_chipset.probe_count > 0) {
218 amd_chipset.probe_count++;
219 spin_unlock_irqrestore(&amd_lock, flags);
220 return;
221 }
222 spin_unlock_irqrestore(&amd_lock, flags);
223
224 if (!amd_chipset_sb_type_init(&info)) {
225 goto commit;
226 }
227
228 switch (info.sb_type.gen) {
229 case AMD_CHIPSET_SB700:
230 info.need_pll_quirk = info.sb_type.rev <= 0x3B;
231 break;
232 case AMD_CHIPSET_SB800:
233 case AMD_CHIPSET_HUDSON2:
234 case AMD_CHIPSET_BOLTON:
235 info.need_pll_quirk = true;
236 break;
237 default:
238 info.need_pll_quirk = false;
239 break;
240 }
241
242 if (!info.need_pll_quirk) {
243 if (info.smbus_dev) {
244 pci_dev_put(info.smbus_dev);
245 info.smbus_dev = NULL;
246 }
247 goto commit;
248 }
249
250 info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x9601, NULL);
251 if (info.nb_dev) {
252 info.nb_type = 1;
253 } else {
254 info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL);
255 if (info.nb_dev) {
256 info.nb_type = 2;
257 } else {
258 info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD,
259 0x9600, NULL);
260 if (info.nb_dev)
261 info.nb_type = 3;
262 }
263 }
264
265 printk(KERN_DEBUG "QUIRK: Enable AMD PLL fix\n");
266
267commit:
268
269 spin_lock_irqsave(&amd_lock, flags);
270 if (amd_chipset.probe_count > 0) {
271 /* race - someone else was faster - drop devices */
272
273 /* Mark that we where here */
274 amd_chipset.probe_count++;
275
276 spin_unlock_irqrestore(&amd_lock, flags);
277
278 pci_dev_put(info.nb_dev);
279 pci_dev_put(info.smbus_dev);
280
281 } else {
282 /* no race - commit the result */
283 info.probe_count++;
284 amd_chipset = info;
285 spin_unlock_irqrestore(&amd_lock, flags);
286 }
287}
288
289int usb_hcd_amd_remote_wakeup_quirk(struct pci_dev *pdev)
290{
291 /* Make sure amd chipset type has already been initialized */
292 usb_amd_find_chipset_info();
293 if (amd_chipset.sb_type.gen == AMD_CHIPSET_YANGTZE ||
294 amd_chipset.sb_type.gen == AMD_CHIPSET_TAISHAN) {
295 dev_dbg(&pdev->dev, "QUIRK: Enable AMD remote wakeup fix\n");
296 return 1;
297 }
298 return 0;
299}
300EXPORT_SYMBOL_GPL(usb_hcd_amd_remote_wakeup_quirk);
301
302bool usb_amd_hang_symptom_quirk(void)
303{
304 u8 rev;
305
306 usb_amd_find_chipset_info();
307 rev = amd_chipset.sb_type.rev;
308 /* SB600 and old version of SB700 have hang symptom bug */
309 return amd_chipset.sb_type.gen == AMD_CHIPSET_SB600 ||
310 (amd_chipset.sb_type.gen == AMD_CHIPSET_SB700 &&
311 rev >= 0x3a && rev <= 0x3b);
312}
313EXPORT_SYMBOL_GPL(usb_amd_hang_symptom_quirk);
314
315bool usb_amd_prefetch_quirk(void)
316{
317 usb_amd_find_chipset_info();
318 /* SB800 needs pre-fetch fix */
319 return amd_chipset.sb_type.gen == AMD_CHIPSET_SB800;
320}
321EXPORT_SYMBOL_GPL(usb_amd_prefetch_quirk);
322
323bool usb_amd_quirk_pll_check(void)
324{
325 usb_amd_find_chipset_info();
326 return amd_chipset.need_pll_quirk;
327}
328EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_check);
329
330/*
331 * The hardware normally enables the A-link power management feature, which
332 * lets the system lower the power consumption in idle states.
333 *
334 * This USB quirk prevents the link going into that lower power state
335 * during isochronous transfers.
336 *
337 * Without this quirk, isochronous stream on OHCI/EHCI/xHCI controllers of
338 * some AMD platforms may stutter or have breaks occasionally.
339 */
340static void usb_amd_quirk_pll(int disable)
341{
342 u32 addr, addr_low, addr_high, val;
343 u32 bit = disable ? 0 : 1;
344 unsigned long flags;
345
346 spin_lock_irqsave(&amd_lock, flags);
347
348 if (disable) {
349 amd_chipset.isoc_reqs++;
350 if (amd_chipset.isoc_reqs > 1) {
351 spin_unlock_irqrestore(&amd_lock, flags);
352 return;
353 }
354 } else {
355 amd_chipset.isoc_reqs--;
356 if (amd_chipset.isoc_reqs > 0) {
357 spin_unlock_irqrestore(&amd_lock, flags);
358 return;
359 }
360 }
361
362 if (amd_chipset.sb_type.gen == AMD_CHIPSET_SB800 ||
363 amd_chipset.sb_type.gen == AMD_CHIPSET_HUDSON2 ||
364 amd_chipset.sb_type.gen == AMD_CHIPSET_BOLTON) {
365 outb_p(AB_REG_BAR_LOW, 0xcd6);
366 addr_low = inb_p(0xcd7);
367 outb_p(AB_REG_BAR_HIGH, 0xcd6);
368 addr_high = inb_p(0xcd7);
369 addr = addr_high << 8 | addr_low;
370
371 outl_p(0x30, AB_INDX(addr));
372 outl_p(0x40, AB_DATA(addr));
373 outl_p(0x34, AB_INDX(addr));
374 val = inl_p(AB_DATA(addr));
375 } else if (amd_chipset.sb_type.gen == AMD_CHIPSET_SB700 &&
376 amd_chipset.sb_type.rev <= 0x3b) {
377 pci_read_config_dword(amd_chipset.smbus_dev,
378 AB_REG_BAR_SB700, &addr);
379 outl(AX_INDXC, AB_INDX(addr));
380 outl(0x40, AB_DATA(addr));
381 outl(AX_DATAC, AB_INDX(addr));
382 val = inl(AB_DATA(addr));
383 } else {
384 spin_unlock_irqrestore(&amd_lock, flags);
385 return;
386 }
387
388 if (disable) {
389 val &= ~0x08;
390 val |= (1 << 4) | (1 << 9);
391 } else {
392 val |= 0x08;
393 val &= ~((1 << 4) | (1 << 9));
394 }
395 outl_p(val, AB_DATA(addr));
396
397 if (!amd_chipset.nb_dev) {
398 spin_unlock_irqrestore(&amd_lock, flags);
399 return;
400 }
401
402 if (amd_chipset.nb_type == 1 || amd_chipset.nb_type == 3) {
403 addr = PCIE_P_CNTL;
404 pci_write_config_dword(amd_chipset.nb_dev,
405 NB_PCIE_INDX_ADDR, addr);
406 pci_read_config_dword(amd_chipset.nb_dev,
407 NB_PCIE_INDX_DATA, &val);
408
409 val &= ~(1 | (1 << 3) | (1 << 4) | (1 << 9) | (1 << 12));
410 val |= bit | (bit << 3) | (bit << 12);
411 val |= ((!bit) << 4) | ((!bit) << 9);
412 pci_write_config_dword(amd_chipset.nb_dev,
413 NB_PCIE_INDX_DATA, val);
414
415 addr = BIF_NB;
416 pci_write_config_dword(amd_chipset.nb_dev,
417 NB_PCIE_INDX_ADDR, addr);
418 pci_read_config_dword(amd_chipset.nb_dev,
419 NB_PCIE_INDX_DATA, &val);
420 val &= ~(1 << 8);
421 val |= bit << 8;
422
423 pci_write_config_dword(amd_chipset.nb_dev,
424 NB_PCIE_INDX_DATA, val);
425 } else if (amd_chipset.nb_type == 2) {
426 addr = NB_PIF0_PWRDOWN_0;
427 pci_write_config_dword(amd_chipset.nb_dev,
428 NB_PCIE_INDX_ADDR, addr);
429 pci_read_config_dword(amd_chipset.nb_dev,
430 NB_PCIE_INDX_DATA, &val);
431 if (disable)
432 val &= ~(0x3f << 7);
433 else
434 val |= 0x3f << 7;
435
436 pci_write_config_dword(amd_chipset.nb_dev,
437 NB_PCIE_INDX_DATA, val);
438
439 addr = NB_PIF0_PWRDOWN_1;
440 pci_write_config_dword(amd_chipset.nb_dev,
441 NB_PCIE_INDX_ADDR, addr);
442 pci_read_config_dword(amd_chipset.nb_dev,
443 NB_PCIE_INDX_DATA, &val);
444 if (disable)
445 val &= ~(0x3f << 7);
446 else
447 val |= 0x3f << 7;
448
449 pci_write_config_dword(amd_chipset.nb_dev,
450 NB_PCIE_INDX_DATA, val);
451 }
452
453 spin_unlock_irqrestore(&amd_lock, flags);
454 return;
455}
456
457void usb_amd_quirk_pll_disable(void)
458{
459 usb_amd_quirk_pll(1);
460}
461EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_disable);
462
463void usb_amd_quirk_pll_enable(void)
464{
465 usb_amd_quirk_pll(0);
466}
467EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_enable);
468
469void usb_amd_dev_put(void)
470{
471 struct pci_dev *nb, *smbus;
472 unsigned long flags;
473
474 spin_lock_irqsave(&amd_lock, flags);
475
476 amd_chipset.probe_count--;
477 if (amd_chipset.probe_count > 0) {
478 spin_unlock_irqrestore(&amd_lock, flags);
479 return;
480 }
481
482 /* save them to pci_dev_put outside of spinlock */
483 nb = amd_chipset.nb_dev;
484 smbus = amd_chipset.smbus_dev;
485
486 amd_chipset.nb_dev = NULL;
487 amd_chipset.smbus_dev = NULL;
488 amd_chipset.nb_type = 0;
489 memset(&amd_chipset.sb_type, 0, sizeof(amd_chipset.sb_type));
490 amd_chipset.isoc_reqs = 0;
491 amd_chipset.need_pll_quirk = false;
492
493 spin_unlock_irqrestore(&amd_lock, flags);
494
495 pci_dev_put(nb);
496 pci_dev_put(smbus);
497}
498EXPORT_SYMBOL_GPL(usb_amd_dev_put);
499
500/*
501 * Check if port is disabled in BIOS on AMD Promontory host.
502 * BIOS Disabled ports may wake on connect/disconnect and need
503 * driver workaround to keep them disabled.
504 * Returns true if port is marked disabled.
505 */
506bool usb_amd_pt_check_port(struct device *device, int port)
507{
508 unsigned char value, port_shift;
509 struct pci_dev *pdev;
510 u16 reg;
511
512 pdev = to_pci_dev(device);
513 pci_write_config_word(pdev, PT_ADDR_INDX, PT_SIG_1_ADDR);
514
515 pci_read_config_byte(pdev, PT_READ_INDX, &value);
516 if (value != PT_SIG_1_DATA)
517 return false;
518
519 pci_write_config_word(pdev, PT_ADDR_INDX, PT_SIG_2_ADDR);
520
521 pci_read_config_byte(pdev, PT_READ_INDX, &value);
522 if (value != PT_SIG_2_DATA)
523 return false;
524
525 pci_write_config_word(pdev, PT_ADDR_INDX, PT_SIG_3_ADDR);
526
527 pci_read_config_byte(pdev, PT_READ_INDX, &value);
528 if (value != PT_SIG_3_DATA)
529 return false;
530
531 pci_write_config_word(pdev, PT_ADDR_INDX, PT_SIG_4_ADDR);
532
533 pci_read_config_byte(pdev, PT_READ_INDX, &value);
534 if (value != PT_SIG_4_DATA)
535 return false;
536
537 /* Check disabled port setting, if bit is set port is enabled */
538 switch (pdev->device) {
539 case 0x43b9:
540 case 0x43ba:
541 /*
542 * device is AMD_PROMONTORYA_4(0x43b9) or PROMONTORYA_3(0x43ba)
543 * PT4_P1_REG bits[7..1] represents USB2.0 ports 6 to 0
544 * PT4_P2_REG bits[6..0] represents ports 13 to 7
545 */
546 if (port > 6) {
547 reg = PT4_P2_REG;
548 port_shift = port - 7;
549 } else {
550 reg = PT4_P1_REG;
551 port_shift = port + 1;
552 }
553 break;
554 case 0x43bb:
555 /*
556 * device is AMD_PROMONTORYA_2(0x43bb)
557 * PT2_P1_REG bits[7..5] represents USB2.0 ports 2 to 0
558 * PT2_P2_REG bits[5..0] represents ports 9 to 3
559 */
560 if (port > 2) {
561 reg = PT2_P2_REG;
562 port_shift = port - 3;
563 } else {
564 reg = PT2_P1_REG;
565 port_shift = port + 5;
566 }
567 break;
568 case 0x43bc:
569 /*
570 * device is AMD_PROMONTORYA_1(0x43bc)
571 * PT1_P1_REG[7..4] represents USB2.0 ports 3 to 0
572 * PT1_P2_REG[5..0] represents ports 9 to 4
573 */
574 if (port > 3) {
575 reg = PT1_P2_REG;
576 port_shift = port - 4;
577 } else {
578 reg = PT1_P1_REG;
579 port_shift = port + 4;
580 }
581 break;
582 default:
583 return false;
584 }
585 pci_write_config_word(pdev, PT_ADDR_INDX, reg);
586 pci_read_config_byte(pdev, PT_READ_INDX, &value);
587
588 return !(value & BIT(port_shift));
589}
590EXPORT_SYMBOL_GPL(usb_amd_pt_check_port);
591#endif /* CONFIG_USB_PCI_AMD */
592
593static int usb_asmedia_wait_write(struct pci_dev *pdev)
594{
595 unsigned long retry_count;
596 unsigned char value;
597
598 for (retry_count = 1000; retry_count > 0; --retry_count) {
599
600 pci_read_config_byte(pdev, ASMT_CONTROL_REG, &value);
601
602 if (value == 0xff) {
603 dev_err(&pdev->dev, "%s: check_ready ERROR", __func__);
604 return -EIO;
605 }
606
607 if ((value & ASMT_CONTROL_WRITE_BIT) == 0)
608 return 0;
609
610 udelay(50);
611 }
612
613 dev_warn(&pdev->dev, "%s: check_write_ready timeout", __func__);
614 return -ETIMEDOUT;
615}
616
617void usb_asmedia_modifyflowcontrol(struct pci_dev *pdev)
618{
619 if (usb_asmedia_wait_write(pdev) != 0)
620 return;
621
622 /* send command and address to device */
623 pci_write_config_dword(pdev, ASMT_DATA_WRITE0_REG, ASMT_WRITEREG_CMD);
624 pci_write_config_dword(pdev, ASMT_DATA_WRITE1_REG, ASMT_FLOWCTL_ADDR);
625 pci_write_config_byte(pdev, ASMT_CONTROL_REG, ASMT_CONTROL_WRITE_BIT);
626
627 if (usb_asmedia_wait_write(pdev) != 0)
628 return;
629
630 /* send data to device */
631 pci_write_config_dword(pdev, ASMT_DATA_WRITE0_REG, ASMT_FLOWCTL_DATA);
632 pci_write_config_dword(pdev, ASMT_DATA_WRITE1_REG, ASMT_PSEUDO_DATA);
633 pci_write_config_byte(pdev, ASMT_CONTROL_REG, ASMT_CONTROL_WRITE_BIT);
634}
635EXPORT_SYMBOL_GPL(usb_asmedia_modifyflowcontrol);
636
637static inline int io_type_enabled(struct pci_dev *pdev, unsigned int mask)
638{
639 u16 cmd;
640
641 return !pci_read_config_word(pdev, PCI_COMMAND, &cmd) && (cmd & mask);
642}
643
644#define mmio_enabled(dev) io_type_enabled(dev, PCI_COMMAND_MEMORY)
645
646#if defined(CONFIG_HAS_IOPORT) && IS_ENABLED(CONFIG_USB_UHCI_HCD)
647/*
648 * Make sure the controller is completely inactive, unable to
649 * generate interrupts or do DMA.
650 */
651void uhci_reset_hc(struct pci_dev *pdev, unsigned long base)
652{
653 /* Turn off PIRQ enable and SMI enable. (This also turns off the
654 * BIOS's USB Legacy Support.) Turn off all the R/WC bits too.
655 */
656 pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_RWC);
657
658 /* Reset the HC - this will force us to get a
659 * new notification of any already connected
660 * ports due to the virtual disconnect that it
661 * implies.
662 */
663 outw(UHCI_USBCMD_HCRESET, base + UHCI_USBCMD);
664 mb();
665 udelay(5);
666 if (inw(base + UHCI_USBCMD) & UHCI_USBCMD_HCRESET)
667 dev_warn(&pdev->dev, "HCRESET not completed yet!\n");
668
669 /* Just to be safe, disable interrupt requests and
670 * make sure the controller is stopped.
671 */
672 outw(0, base + UHCI_USBINTR);
673 outw(0, base + UHCI_USBCMD);
674}
675EXPORT_SYMBOL_GPL(uhci_reset_hc);
676
677/*
678 * Initialize a controller that was newly discovered or has just been
679 * resumed. In either case we can't be sure of its previous state.
680 *
681 * Returns: 1 if the controller was reset, 0 otherwise.
682 */
683int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base)
684{
685 u16 legsup;
686 unsigned int cmd, intr;
687
688 /*
689 * When restarting a suspended controller, we expect all the
690 * settings to be the same as we left them:
691 *
692 * PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
693 * Controller is stopped and configured with EGSM set;
694 * No interrupts enabled except possibly Resume Detect.
695 *
696 * If any of these conditions are violated we do a complete reset.
697 */
698 pci_read_config_word(pdev, UHCI_USBLEGSUP, &legsup);
699 if (legsup & ~(UHCI_USBLEGSUP_RO | UHCI_USBLEGSUP_RWC)) {
700 dev_dbg(&pdev->dev, "%s: legsup = 0x%04x\n",
701 __func__, legsup);
702 goto reset_needed;
703 }
704
705 cmd = inw(base + UHCI_USBCMD);
706 if ((cmd & UHCI_USBCMD_RUN) || !(cmd & UHCI_USBCMD_CONFIGURE) ||
707 !(cmd & UHCI_USBCMD_EGSM)) {
708 dev_dbg(&pdev->dev, "%s: cmd = 0x%04x\n",
709 __func__, cmd);
710 goto reset_needed;
711 }
712
713 intr = inw(base + UHCI_USBINTR);
714 if (intr & (~UHCI_USBINTR_RESUME)) {
715 dev_dbg(&pdev->dev, "%s: intr = 0x%04x\n",
716 __func__, intr);
717 goto reset_needed;
718 }
719 return 0;
720
721reset_needed:
722 dev_dbg(&pdev->dev, "Performing full reset\n");
723 uhci_reset_hc(pdev, base);
724 return 1;
725}
726EXPORT_SYMBOL_GPL(uhci_check_and_reset_hc);
727
728#define pio_enabled(dev) io_type_enabled(dev, PCI_COMMAND_IO)
729
730static void quirk_usb_handoff_uhci(struct pci_dev *pdev)
731{
732 unsigned long base = 0;
733 int i;
734
735 if (!pio_enabled(pdev))
736 return;
737
738 for (i = 0; i < PCI_STD_NUM_BARS; i++)
739 if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
740 base = pci_resource_start(pdev, i);
741 break;
742 }
743
744 if (base)
745 uhci_check_and_reset_hc(pdev, base);
746}
747
748#else /* defined(CONFIG_HAS_IOPORT && IS_ENABLED(CONFIG_USB_UHCI_HCD) */
749
750static void quirk_usb_handoff_uhci(struct pci_dev *pdev) {}
751
752#endif /* defined(CONFIG_HAS_IOPORT && IS_ENABLED(CONFIG_USB_UHCI_HCD) */
753
754static int mmio_resource_enabled(struct pci_dev *pdev, int idx)
755{
756 return pci_resource_start(pdev, idx) && mmio_enabled(pdev);
757}
758
759static void quirk_usb_handoff_ohci(struct pci_dev *pdev)
760{
761 void __iomem *base;
762 u32 control;
763 u32 fminterval = 0;
764 bool no_fminterval = false;
765 int cnt;
766
767 if (!mmio_resource_enabled(pdev, 0))
768 return;
769
770 base = pci_ioremap_bar(pdev, 0);
771 if (base == NULL)
772 return;
773
774 /*
775 * ULi M5237 OHCI controller locks the whole system when accessing
776 * the OHCI_FMINTERVAL offset.
777 */
778 if (pdev->vendor == PCI_VENDOR_ID_AL && pdev->device == 0x5237)
779 no_fminterval = true;
780
781 control = readl(base + OHCI_CONTROL);
782
783/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
784#ifdef __hppa__
785#define OHCI_CTRL_MASK (OHCI_CTRL_RWC | OHCI_CTRL_IR)
786#else
787#define OHCI_CTRL_MASK OHCI_CTRL_RWC
788
789 if (control & OHCI_CTRL_IR) {
790 int wait_time = 500; /* arbitrary; 5 seconds */
791 writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
792 writel(OHCI_OCR, base + OHCI_CMDSTATUS);
793 while (wait_time > 0 &&
794 readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
795 wait_time -= 10;
796 msleep(10);
797 }
798 if (wait_time <= 0)
799 dev_warn(&pdev->dev,
800 "OHCI: BIOS handoff failed (BIOS bug?) %08x\n",
801 readl(base + OHCI_CONTROL));
802 }
803#endif
804
805 /* disable interrupts */
806 writel((u32) ~0, base + OHCI_INTRDISABLE);
807
808 /* Go into the USB_RESET state, preserving RWC (and possibly IR) */
809 writel(control & OHCI_CTRL_MASK, base + OHCI_CONTROL);
810 readl(base + OHCI_CONTROL);
811
812 /* software reset of the controller, preserving HcFmInterval */
813 if (!no_fminterval)
814 fminterval = readl(base + OHCI_FMINTERVAL);
815
816 writel(OHCI_HCR, base + OHCI_CMDSTATUS);
817
818 /* reset requires max 10 us delay */
819 for (cnt = 30; cnt > 0; --cnt) { /* ... allow extra time */
820 if ((readl(base + OHCI_CMDSTATUS) & OHCI_HCR) == 0)
821 break;
822 udelay(1);
823 }
824
825 if (!no_fminterval)
826 writel(fminterval, base + OHCI_FMINTERVAL);
827
828 /* Now the controller is safely in SUSPEND and nothing can wake it up */
829 iounmap(base);
830}
831
832static const struct dmi_system_id ehci_dmi_nohandoff_table[] = {
833 {
834 /* Pegatron Lucid (ExoPC) */
835 .matches = {
836 DMI_MATCH(DMI_BOARD_NAME, "EXOPG06411"),
837 DMI_MATCH(DMI_BIOS_VERSION, "Lucid-CE-133"),
838 },
839 },
840 {
841 /* Pegatron Lucid (Ordissimo AIRIS) */
842 .matches = {
843 DMI_MATCH(DMI_BOARD_NAME, "M11JB"),
844 DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
845 },
846 },
847 {
848 /* Pegatron Lucid (Ordissimo) */
849 .matches = {
850 DMI_MATCH(DMI_BOARD_NAME, "Ordissimo"),
851 DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
852 },
853 },
854 {
855 /* HASEE E200 */
856 .matches = {
857 DMI_MATCH(DMI_BOARD_VENDOR, "HASEE"),
858 DMI_MATCH(DMI_BOARD_NAME, "E210"),
859 DMI_MATCH(DMI_BIOS_VERSION, "6.00"),
860 },
861 },
862 { }
863};
864
865static void ehci_bios_handoff(struct pci_dev *pdev,
866 void __iomem *op_reg_base,
867 u32 cap, u8 offset)
868{
869 int try_handoff = 1, tried_handoff = 0;
870
871 /*
872 * The Pegatron Lucid tablet sporadically waits for 98 seconds trying
873 * the handoff on its unused controller. Skip it.
874 *
875 * The HASEE E200 hangs when the semaphore is set (bugzilla #77021).
876 */
877 if (pdev->vendor == 0x8086 && (pdev->device == 0x283a ||
878 pdev->device == 0x27cc)) {
879 if (dmi_check_system(ehci_dmi_nohandoff_table))
880 try_handoff = 0;
881 }
882
883 if (try_handoff && (cap & EHCI_USBLEGSUP_BIOS)) {
884 dev_dbg(&pdev->dev, "EHCI: BIOS handoff\n");
885
886#if 0
887/* aleksey_gorelov@phoenix.com reports that some systems need SMI forced on,
888 * but that seems dubious in general (the BIOS left it off intentionally)
889 * and is known to prevent some systems from booting. so we won't do this
890 * unless maybe we can determine when we're on a system that needs SMI forced.
891 */
892 /* BIOS workaround (?): be sure the pre-Linux code
893 * receives the SMI
894 */
895 pci_read_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, &val);
896 pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS,
897 val | EHCI_USBLEGCTLSTS_SOOE);
898#endif
899
900 /* some systems get upset if this semaphore is
901 * set for any other reason than forcing a BIOS
902 * handoff..
903 */
904 pci_write_config_byte(pdev, offset + 3, 1);
905 }
906
907 /* if boot firmware now owns EHCI, spin till it hands it over. */
908 if (try_handoff) {
909 int msec = 1000;
910 while ((cap & EHCI_USBLEGSUP_BIOS) && (msec > 0)) {
911 tried_handoff = 1;
912 msleep(10);
913 msec -= 10;
914 pci_read_config_dword(pdev, offset, &cap);
915 }
916 }
917
918 if (cap & EHCI_USBLEGSUP_BIOS) {
919 /* well, possibly buggy BIOS... try to shut it down,
920 * and hope nothing goes too wrong
921 */
922 if (try_handoff)
923 dev_warn(&pdev->dev,
924 "EHCI: BIOS handoff failed (BIOS bug?) %08x\n",
925 cap);
926 pci_write_config_byte(pdev, offset + 2, 0);
927 }
928
929 /* just in case, always disable EHCI SMIs */
930 pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, 0);
931
932 /* If the BIOS ever owned the controller then we can't expect
933 * any power sessions to remain intact.
934 */
935 if (tried_handoff)
936 writel(0, op_reg_base + EHCI_CONFIGFLAG);
937}
938
939static void quirk_usb_disable_ehci(struct pci_dev *pdev)
940{
941 void __iomem *base, *op_reg_base;
942 u32 hcc_params, cap, val;
943 u8 offset, cap_length;
944 int wait_time, count = 256/4;
945
946 if (!mmio_resource_enabled(pdev, 0))
947 return;
948
949 base = pci_ioremap_bar(pdev, 0);
950 if (base == NULL)
951 return;
952
953 cap_length = readb(base);
954 op_reg_base = base + cap_length;
955
956 /* EHCI 0.96 and later may have "extended capabilities"
957 * spec section 5.1 explains the bios handoff, e.g. for
958 * booting from USB disk or using a usb keyboard
959 */
960 hcc_params = readl(base + EHCI_HCC_PARAMS);
961 offset = (hcc_params >> 8) & 0xff;
962 while (offset && --count) {
963 pci_read_config_dword(pdev, offset, &cap);
964
965 switch (cap & 0xff) {
966 case 1:
967 ehci_bios_handoff(pdev, op_reg_base, cap, offset);
968 break;
969 case 0: /* Illegal reserved cap, set cap=0 so we exit */
970 cap = 0;
971 fallthrough;
972 default:
973 dev_warn(&pdev->dev,
974 "EHCI: unrecognized capability %02x\n",
975 cap & 0xff);
976 }
977 offset = (cap >> 8) & 0xff;
978 }
979 if (!count)
980 dev_printk(KERN_DEBUG, &pdev->dev, "EHCI: capability loop?\n");
981
982 /*
983 * halt EHCI & disable its interrupts in any case
984 */
985 val = readl(op_reg_base + EHCI_USBSTS);
986 if ((val & EHCI_USBSTS_HALTED) == 0) {
987 val = readl(op_reg_base + EHCI_USBCMD);
988 val &= ~EHCI_USBCMD_RUN;
989 writel(val, op_reg_base + EHCI_USBCMD);
990
991 wait_time = 2000;
992 do {
993 writel(0x3f, op_reg_base + EHCI_USBSTS);
994 udelay(100);
995 wait_time -= 100;
996 val = readl(op_reg_base + EHCI_USBSTS);
997 if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
998 break;
999 }
1000 } while (wait_time > 0);
1001 }
1002 writel(0, op_reg_base + EHCI_USBINTR);
1003 writel(0x3f, op_reg_base + EHCI_USBSTS);
1004
1005 iounmap(base);
1006}
1007
1008/*
1009 * handshake - spin reading a register until handshake completes
1010 * @ptr: address of hc register to be read
1011 * @mask: bits to look at in result of read
1012 * @done: value of those bits when handshake succeeds
1013 * @wait_usec: timeout in microseconds
1014 * @delay_usec: delay in microseconds to wait between polling
1015 *
1016 * Polls a register every delay_usec microseconds.
1017 * Returns 0 when the mask bits have the value done.
1018 * Returns -ETIMEDOUT if this condition is not true after
1019 * wait_usec microseconds have passed.
1020 */
1021static int handshake(void __iomem *ptr, u32 mask, u32 done,
1022 int wait_usec, int delay_usec)
1023{
1024 u32 result;
1025
1026 return readl_poll_timeout_atomic(ptr, result,
1027 ((result & mask) == done),
1028 delay_usec, wait_usec);
1029}
1030
1031/*
1032 * Intel's Panther Point chipset has two host controllers (EHCI and xHCI) that
1033 * share some number of ports. These ports can be switched between either
1034 * controller. Not all of the ports under the EHCI host controller may be
1035 * switchable.
1036 *
1037 * The ports should be switched over to xHCI before PCI probes for any device
1038 * start. This avoids active devices under EHCI being disconnected during the
1039 * port switchover, which could cause loss of data on USB storage devices, or
1040 * failed boot when the root file system is on a USB mass storage device and is
1041 * enumerated under EHCI first.
1042 *
1043 * We write into the xHC's PCI configuration space in some Intel-specific
1044 * registers to switch the ports over. The USB 3.0 terminations and the USB
1045 * 2.0 data wires are switched separately. We want to enable the SuperSpeed
1046 * terminations before switching the USB 2.0 wires over, so that USB 3.0
1047 * devices connect at SuperSpeed, rather than at USB 2.0 speeds.
1048 */
1049void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
1050{
1051 u32 ports_available;
1052 bool ehci_found = false;
1053 struct pci_dev *companion = NULL;
1054
1055 /* Sony VAIO t-series with subsystem device ID 90a8 is not capable of
1056 * switching ports from EHCI to xHCI
1057 */
1058 if (xhci_pdev->subsystem_vendor == PCI_VENDOR_ID_SONY &&
1059 xhci_pdev->subsystem_device == 0x90a8)
1060 return;
1061
1062 /* make sure an intel EHCI controller exists */
1063 for_each_pci_dev(companion) {
1064 if (companion->class == PCI_CLASS_SERIAL_USB_EHCI &&
1065 companion->vendor == PCI_VENDOR_ID_INTEL) {
1066 ehci_found = true;
1067 break;
1068 }
1069 }
1070
1071 if (!ehci_found)
1072 return;
1073
1074 /* Don't switchover the ports if the user hasn't compiled the xHCI
1075 * driver. Otherwise they will see "dead" USB ports that don't power
1076 * the devices.
1077 */
1078 if (!IS_ENABLED(CONFIG_USB_XHCI_HCD)) {
1079 dev_warn(&xhci_pdev->dev,
1080 "CONFIG_USB_XHCI_HCD is turned off, defaulting to EHCI.\n");
1081 dev_warn(&xhci_pdev->dev,
1082 "USB 3.0 devices will work at USB 2.0 speeds.\n");
1083 usb_disable_xhci_ports(xhci_pdev);
1084 return;
1085 }
1086
1087 /* Read USB3PRM, the USB 3.0 Port Routing Mask Register
1088 * Indicate the ports that can be changed from OS.
1089 */
1090 pci_read_config_dword(xhci_pdev, USB_INTEL_USB3PRM,
1091 &ports_available);
1092
1093 dev_dbg(&xhci_pdev->dev, "Configurable ports to enable SuperSpeed: 0x%x\n",
1094 ports_available);
1095
1096 /* Write USB3_PSSEN, the USB 3.0 Port SuperSpeed Enable
1097 * Register, to turn on SuperSpeed terminations for the
1098 * switchable ports.
1099 */
1100 pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
1101 ports_available);
1102
1103 pci_read_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
1104 &ports_available);
1105 dev_dbg(&xhci_pdev->dev,
1106 "USB 3.0 ports that are now enabled under xHCI: 0x%x\n",
1107 ports_available);
1108
1109 /* Read XUSB2PRM, xHCI USB 2.0 Port Routing Mask Register
1110 * Indicate the USB 2.0 ports to be controlled by the xHCI host.
1111 */
1112
1113 pci_read_config_dword(xhci_pdev, USB_INTEL_USB2PRM,
1114 &ports_available);
1115
1116 dev_dbg(&xhci_pdev->dev, "Configurable USB 2.0 ports to hand over to xCHI: 0x%x\n",
1117 ports_available);
1118
1119 /* Write XUSB2PR, the xHC USB 2.0 Port Routing Register, to
1120 * switch the USB 2.0 power and data lines over to the xHCI
1121 * host.
1122 */
1123 pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
1124 ports_available);
1125
1126 pci_read_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
1127 &ports_available);
1128 dev_dbg(&xhci_pdev->dev,
1129 "USB 2.0 ports that are now switched over to xHCI: 0x%x\n",
1130 ports_available);
1131}
1132EXPORT_SYMBOL_GPL(usb_enable_intel_xhci_ports);
1133
1134void usb_disable_xhci_ports(struct pci_dev *xhci_pdev)
1135{
1136 pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN, 0x0);
1137 pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR, 0x0);
1138}
1139EXPORT_SYMBOL_GPL(usb_disable_xhci_ports);
1140
1141/*
1142 * PCI Quirks for xHCI.
1143 *
1144 * Takes care of the handoff between the Pre-OS (i.e. BIOS) and the OS.
1145 * It signals to the BIOS that the OS wants control of the host controller,
1146 * and then waits 1 second for the BIOS to hand over control.
1147 * If we timeout, assume the BIOS is broken and take control anyway.
1148 */
1149static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
1150{
1151 void __iomem *base;
1152 int ext_cap_offset;
1153 void __iomem *op_reg_base;
1154 u32 val;
1155 int timeout;
1156 int len = pci_resource_len(pdev, 0);
1157
1158 if (!mmio_resource_enabled(pdev, 0))
1159 return;
1160
1161 base = ioremap(pci_resource_start(pdev, 0), len);
1162 if (base == NULL)
1163 return;
1164
1165 /*
1166 * Find the Legacy Support Capability register -
1167 * this is optional for xHCI host controllers.
1168 */
1169 ext_cap_offset = xhci_find_next_ext_cap(base, 0, XHCI_EXT_CAPS_LEGACY);
1170
1171 if (!ext_cap_offset)
1172 goto hc_init;
1173
1174 if ((ext_cap_offset + sizeof(val)) > len) {
1175 /* We're reading garbage from the controller */
1176 dev_warn(&pdev->dev, "xHCI controller failing to respond");
1177 goto iounmap;
1178 }
1179 val = readl(base + ext_cap_offset);
1180
1181 /* Auto handoff never worked for these devices. Force it and continue */
1182 if ((pdev->vendor == PCI_VENDOR_ID_TI && pdev->device == 0x8241) ||
1183 (pdev->vendor == PCI_VENDOR_ID_RENESAS
1184 && pdev->device == 0x0014)) {
1185 val = (val | XHCI_HC_OS_OWNED) & ~XHCI_HC_BIOS_OWNED;
1186 writel(val, base + ext_cap_offset);
1187 }
1188
1189 /* If the BIOS owns the HC, signal that the OS wants it, and wait */
1190 if (val & XHCI_HC_BIOS_OWNED) {
1191 writel(val | XHCI_HC_OS_OWNED, base + ext_cap_offset);
1192
1193 /* Wait for 1 second with 10 microsecond polling interval */
1194 timeout = handshake(base + ext_cap_offset, XHCI_HC_BIOS_OWNED,
1195 0, 1000000, 10);
1196
1197 /* Assume a buggy BIOS and take HC ownership anyway */
1198 if (timeout) {
1199 dev_warn(&pdev->dev,
1200 "xHCI BIOS handoff failed (BIOS bug ?) %08x\n",
1201 val);
1202 writel(val & ~XHCI_HC_BIOS_OWNED, base + ext_cap_offset);
1203 }
1204 }
1205
1206 val = readl(base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
1207 /* Mask off (turn off) any enabled SMIs */
1208 val &= XHCI_LEGACY_DISABLE_SMI;
1209 /* Mask all SMI events bits, RW1C */
1210 val |= XHCI_LEGACY_SMI_EVENTS;
1211 /* Disable any BIOS SMIs and clear all SMI events*/
1212 writel(val, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
1213
1214hc_init:
1215 if (pdev->vendor == PCI_VENDOR_ID_INTEL)
1216 usb_enable_intel_xhci_ports(pdev);
1217
1218 op_reg_base = base + XHCI_HC_LENGTH(readl(base));
1219
1220 /* Wait for the host controller to be ready before writing any
1221 * operational or runtime registers. Wait 5 seconds and no more.
1222 */
1223 timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_CNR, 0,
1224 5000000, 10);
1225 /* Assume a buggy HC and start HC initialization anyway */
1226 if (timeout) {
1227 val = readl(op_reg_base + XHCI_STS_OFFSET);
1228 dev_warn(&pdev->dev,
1229 "xHCI HW not ready after 5 sec (HC bug?) status = 0x%x\n",
1230 val);
1231 }
1232
1233 /* Send the halt and disable interrupts command */
1234 val = readl(op_reg_base + XHCI_CMD_OFFSET);
1235 val &= ~(XHCI_CMD_RUN | XHCI_IRQS);
1236 writel(val, op_reg_base + XHCI_CMD_OFFSET);
1237
1238 /* Wait for the HC to halt - poll every 125 usec (one microframe). */
1239 timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_HALT, 1,
1240 XHCI_MAX_HALT_USEC, 125);
1241 if (timeout) {
1242 val = readl(op_reg_base + XHCI_STS_OFFSET);
1243 dev_warn(&pdev->dev,
1244 "xHCI HW did not halt within %d usec status = 0x%x\n",
1245 XHCI_MAX_HALT_USEC, val);
1246 }
1247
1248iounmap:
1249 iounmap(base);
1250}
1251
1252static void quirk_usb_early_handoff(struct pci_dev *pdev)
1253{
1254 struct device_node *parent;
1255 bool is_rpi;
1256
1257 /* Skip Netlogic mips SoC's internal PCI USB controller.
1258 * This device does not need/support EHCI/OHCI handoff
1259 */
1260 if (pdev->vendor == 0x184e) /* vendor Netlogic */
1261 return;
1262
1263 /*
1264 * Bypass the Raspberry Pi 4 controller xHCI controller, things are
1265 * taken care of by the board's co-processor.
1266 */
1267 if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == 0x3483) {
1268 parent = of_get_parent(pdev->bus->dev.of_node);
1269 is_rpi = of_device_is_compatible(parent, "brcm,bcm2711-pcie");
1270 of_node_put(parent);
1271 if (is_rpi)
1272 return;
1273 }
1274
1275 if (pdev->class != PCI_CLASS_SERIAL_USB_UHCI &&
1276 pdev->class != PCI_CLASS_SERIAL_USB_OHCI &&
1277 pdev->class != PCI_CLASS_SERIAL_USB_EHCI &&
1278 pdev->class != PCI_CLASS_SERIAL_USB_XHCI)
1279 return;
1280
1281 if (pci_enable_device(pdev) < 0) {
1282 dev_warn(&pdev->dev,
1283 "Can't enable PCI device, BIOS handoff failed.\n");
1284 return;
1285 }
1286 if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
1287 quirk_usb_handoff_uhci(pdev);
1288 else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
1289 quirk_usb_handoff_ohci(pdev);
1290 else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
1291 quirk_usb_disable_ehci(pdev);
1292 else if (pdev->class == PCI_CLASS_SERIAL_USB_XHCI)
1293 quirk_usb_handoff_xhci(pdev);
1294 pci_disable_device(pdev);
1295}
1296DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
1297 PCI_CLASS_SERIAL_USB, 8, quirk_usb_early_handoff);
1/*
2 * This file contains code to reset and initialize USB host controllers.
3 * Some of it includes work-arounds for PCI hardware and BIOS quirks.
4 * It may need to run early during booting -- before USB would normally
5 * initialize -- to ensure that Linux doesn't use any legacy modes.
6 *
7 * Copyright (c) 1999 Martin Mares <mj@ucw.cz>
8 * (and others)
9 */
10
11#include <linux/types.h>
12#include <linux/kernel.h>
13#include <linux/pci.h>
14#include <linux/delay.h>
15#include <linux/export.h>
16#include <linux/acpi.h>
17#include <linux/dmi.h>
18#include "pci-quirks.h"
19#include "xhci-ext-caps.h"
20
21
22#define UHCI_USBLEGSUP 0xc0 /* legacy support */
23#define UHCI_USBCMD 0 /* command register */
24#define UHCI_USBINTR 4 /* interrupt register */
25#define UHCI_USBLEGSUP_RWC 0x8f00 /* the R/WC bits */
26#define UHCI_USBLEGSUP_RO 0x5040 /* R/O and reserved bits */
27#define UHCI_USBCMD_RUN 0x0001 /* RUN/STOP bit */
28#define UHCI_USBCMD_HCRESET 0x0002 /* Host Controller reset */
29#define UHCI_USBCMD_EGSM 0x0008 /* Global Suspend Mode */
30#define UHCI_USBCMD_CONFIGURE 0x0040 /* Config Flag */
31#define UHCI_USBINTR_RESUME 0x0002 /* Resume interrupt enable */
32
33#define OHCI_CONTROL 0x04
34#define OHCI_CMDSTATUS 0x08
35#define OHCI_INTRSTATUS 0x0c
36#define OHCI_INTRENABLE 0x10
37#define OHCI_INTRDISABLE 0x14
38#define OHCI_FMINTERVAL 0x34
39#define OHCI_HCFS (3 << 6) /* hc functional state */
40#define OHCI_HCR (1 << 0) /* host controller reset */
41#define OHCI_OCR (1 << 3) /* ownership change request */
42#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */
43#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
44#define OHCI_INTR_OC (1 << 30) /* ownership change */
45
46#define EHCI_HCC_PARAMS 0x08 /* extended capabilities */
47#define EHCI_USBCMD 0 /* command register */
48#define EHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
49#define EHCI_USBSTS 4 /* status register */
50#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
51#define EHCI_USBINTR 8 /* interrupt register */
52#define EHCI_CONFIGFLAG 0x40 /* configured flag register */
53#define EHCI_USBLEGSUP 0 /* legacy support register */
54#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
55#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
56#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
57#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI on ownership change */
58
59/* AMD quirk use */
60#define AB_REG_BAR_LOW 0xe0
61#define AB_REG_BAR_HIGH 0xe1
62#define AB_REG_BAR_SB700 0xf0
63#define AB_INDX(addr) ((addr) + 0x00)
64#define AB_DATA(addr) ((addr) + 0x04)
65#define AX_INDXC 0x30
66#define AX_DATAC 0x34
67
68#define NB_PCIE_INDX_ADDR 0xe0
69#define NB_PCIE_INDX_DATA 0xe4
70#define PCIE_P_CNTL 0x10040
71#define BIF_NB 0x10002
72#define NB_PIF0_PWRDOWN_0 0x01100012
73#define NB_PIF0_PWRDOWN_1 0x01100013
74
75#define USB_INTEL_XUSB2PR 0xD0
76#define USB_INTEL_USB2PRM 0xD4
77#define USB_INTEL_USB3_PSSEN 0xD8
78#define USB_INTEL_USB3PRM 0xDC
79
80/*
81 * amd_chipset_gen values represent AMD different chipset generations
82 */
83enum amd_chipset_gen {
84 NOT_AMD_CHIPSET = 0,
85 AMD_CHIPSET_SB600,
86 AMD_CHIPSET_SB700,
87 AMD_CHIPSET_SB800,
88 AMD_CHIPSET_HUDSON2,
89 AMD_CHIPSET_BOLTON,
90 AMD_CHIPSET_YANGTZE,
91 AMD_CHIPSET_UNKNOWN,
92};
93
94struct amd_chipset_type {
95 enum amd_chipset_gen gen;
96 u8 rev;
97};
98
99static struct amd_chipset_info {
100 struct pci_dev *nb_dev;
101 struct pci_dev *smbus_dev;
102 int nb_type;
103 struct amd_chipset_type sb_type;
104 int isoc_reqs;
105 int probe_count;
106 int probe_result;
107} amd_chipset;
108
109static DEFINE_SPINLOCK(amd_lock);
110
111/*
112 * amd_chipset_sb_type_init - initialize amd chipset southbridge type
113 *
114 * AMD FCH/SB generation and revision is identified by SMBus controller
115 * vendor, device and revision IDs.
116 *
117 * Returns: 1 if it is an AMD chipset, 0 otherwise.
118 */
119static int amd_chipset_sb_type_init(struct amd_chipset_info *pinfo)
120{
121 u8 rev = 0;
122 pinfo->sb_type.gen = AMD_CHIPSET_UNKNOWN;
123
124 pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI,
125 PCI_DEVICE_ID_ATI_SBX00_SMBUS, NULL);
126 if (pinfo->smbus_dev) {
127 rev = pinfo->smbus_dev->revision;
128 if (rev >= 0x10 && rev <= 0x1f)
129 pinfo->sb_type.gen = AMD_CHIPSET_SB600;
130 else if (rev >= 0x30 && rev <= 0x3f)
131 pinfo->sb_type.gen = AMD_CHIPSET_SB700;
132 else if (rev >= 0x40 && rev <= 0x4f)
133 pinfo->sb_type.gen = AMD_CHIPSET_SB800;
134 } else {
135 pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
136 PCI_DEVICE_ID_AMD_HUDSON2_SMBUS, NULL);
137
138 if (!pinfo->smbus_dev) {
139 pinfo->sb_type.gen = NOT_AMD_CHIPSET;
140 return 0;
141 }
142
143 rev = pinfo->smbus_dev->revision;
144 if (rev >= 0x11 && rev <= 0x14)
145 pinfo->sb_type.gen = AMD_CHIPSET_HUDSON2;
146 else if (rev >= 0x15 && rev <= 0x18)
147 pinfo->sb_type.gen = AMD_CHIPSET_BOLTON;
148 else if (rev >= 0x39 && rev <= 0x3a)
149 pinfo->sb_type.gen = AMD_CHIPSET_YANGTZE;
150 }
151
152 pinfo->sb_type.rev = rev;
153 return 1;
154}
155
156void sb800_prefetch(struct device *dev, int on)
157{
158 u16 misc;
159 struct pci_dev *pdev = to_pci_dev(dev);
160
161 pci_read_config_word(pdev, 0x50, &misc);
162 if (on == 0)
163 pci_write_config_word(pdev, 0x50, misc & 0xfcff);
164 else
165 pci_write_config_word(pdev, 0x50, misc | 0x0300);
166}
167EXPORT_SYMBOL_GPL(sb800_prefetch);
168
169int usb_amd_find_chipset_info(void)
170{
171 unsigned long flags;
172 struct amd_chipset_info info;
173 int ret;
174
175 spin_lock_irqsave(&amd_lock, flags);
176
177 /* probe only once */
178 if (amd_chipset.probe_count > 0) {
179 amd_chipset.probe_count++;
180 spin_unlock_irqrestore(&amd_lock, flags);
181 return amd_chipset.probe_result;
182 }
183 memset(&info, 0, sizeof(info));
184 spin_unlock_irqrestore(&amd_lock, flags);
185
186 if (!amd_chipset_sb_type_init(&info)) {
187 ret = 0;
188 goto commit;
189 }
190
191 /* Below chipset generations needn't enable AMD PLL quirk */
192 if (info.sb_type.gen == AMD_CHIPSET_UNKNOWN ||
193 info.sb_type.gen == AMD_CHIPSET_SB600 ||
194 info.sb_type.gen == AMD_CHIPSET_YANGTZE ||
195 (info.sb_type.gen == AMD_CHIPSET_SB700 &&
196 info.sb_type.rev > 0x3b)) {
197 if (info.smbus_dev) {
198 pci_dev_put(info.smbus_dev);
199 info.smbus_dev = NULL;
200 }
201 ret = 0;
202 goto commit;
203 }
204
205 info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x9601, NULL);
206 if (info.nb_dev) {
207 info.nb_type = 1;
208 } else {
209 info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL);
210 if (info.nb_dev) {
211 info.nb_type = 2;
212 } else {
213 info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD,
214 0x9600, NULL);
215 if (info.nb_dev)
216 info.nb_type = 3;
217 }
218 }
219
220 ret = info.probe_result = 1;
221 printk(KERN_DEBUG "QUIRK: Enable AMD PLL fix\n");
222
223commit:
224
225 spin_lock_irqsave(&amd_lock, flags);
226 if (amd_chipset.probe_count > 0) {
227 /* race - someone else was faster - drop devices */
228
229 /* Mark that we where here */
230 amd_chipset.probe_count++;
231 ret = amd_chipset.probe_result;
232
233 spin_unlock_irqrestore(&amd_lock, flags);
234
235 pci_dev_put(info.nb_dev);
236 pci_dev_put(info.smbus_dev);
237
238 } else {
239 /* no race - commit the result */
240 info.probe_count++;
241 amd_chipset = info;
242 spin_unlock_irqrestore(&amd_lock, flags);
243 }
244
245 return ret;
246}
247EXPORT_SYMBOL_GPL(usb_amd_find_chipset_info);
248
249int usb_hcd_amd_remote_wakeup_quirk(struct pci_dev *pdev)
250{
251 /* Make sure amd chipset type has already been initialized */
252 usb_amd_find_chipset_info();
253 if (amd_chipset.sb_type.gen != AMD_CHIPSET_YANGTZE)
254 return 0;
255
256 dev_dbg(&pdev->dev, "QUIRK: Enable AMD remote wakeup fix\n");
257 return 1;
258}
259EXPORT_SYMBOL_GPL(usb_hcd_amd_remote_wakeup_quirk);
260
261bool usb_amd_hang_symptom_quirk(void)
262{
263 u8 rev;
264
265 usb_amd_find_chipset_info();
266 rev = amd_chipset.sb_type.rev;
267 /* SB600 and old version of SB700 have hang symptom bug */
268 return amd_chipset.sb_type.gen == AMD_CHIPSET_SB600 ||
269 (amd_chipset.sb_type.gen == AMD_CHIPSET_SB700 &&
270 rev >= 0x3a && rev <= 0x3b);
271}
272EXPORT_SYMBOL_GPL(usb_amd_hang_symptom_quirk);
273
274bool usb_amd_prefetch_quirk(void)
275{
276 usb_amd_find_chipset_info();
277 /* SB800 needs pre-fetch fix */
278 return amd_chipset.sb_type.gen == AMD_CHIPSET_SB800;
279}
280EXPORT_SYMBOL_GPL(usb_amd_prefetch_quirk);
281
282/*
283 * The hardware normally enables the A-link power management feature, which
284 * lets the system lower the power consumption in idle states.
285 *
286 * This USB quirk prevents the link going into that lower power state
287 * during isochronous transfers.
288 *
289 * Without this quirk, isochronous stream on OHCI/EHCI/xHCI controllers of
290 * some AMD platforms may stutter or have breaks occasionally.
291 */
292static void usb_amd_quirk_pll(int disable)
293{
294 u32 addr, addr_low, addr_high, val;
295 u32 bit = disable ? 0 : 1;
296 unsigned long flags;
297
298 spin_lock_irqsave(&amd_lock, flags);
299
300 if (disable) {
301 amd_chipset.isoc_reqs++;
302 if (amd_chipset.isoc_reqs > 1) {
303 spin_unlock_irqrestore(&amd_lock, flags);
304 return;
305 }
306 } else {
307 amd_chipset.isoc_reqs--;
308 if (amd_chipset.isoc_reqs > 0) {
309 spin_unlock_irqrestore(&amd_lock, flags);
310 return;
311 }
312 }
313
314 if (amd_chipset.sb_type.gen == AMD_CHIPSET_SB800 ||
315 amd_chipset.sb_type.gen == AMD_CHIPSET_HUDSON2 ||
316 amd_chipset.sb_type.gen == AMD_CHIPSET_BOLTON) {
317 outb_p(AB_REG_BAR_LOW, 0xcd6);
318 addr_low = inb_p(0xcd7);
319 outb_p(AB_REG_BAR_HIGH, 0xcd6);
320 addr_high = inb_p(0xcd7);
321 addr = addr_high << 8 | addr_low;
322
323 outl_p(0x30, AB_INDX(addr));
324 outl_p(0x40, AB_DATA(addr));
325 outl_p(0x34, AB_INDX(addr));
326 val = inl_p(AB_DATA(addr));
327 } else if (amd_chipset.sb_type.gen == AMD_CHIPSET_SB700 &&
328 amd_chipset.sb_type.rev <= 0x3b) {
329 pci_read_config_dword(amd_chipset.smbus_dev,
330 AB_REG_BAR_SB700, &addr);
331 outl(AX_INDXC, AB_INDX(addr));
332 outl(0x40, AB_DATA(addr));
333 outl(AX_DATAC, AB_INDX(addr));
334 val = inl(AB_DATA(addr));
335 } else {
336 spin_unlock_irqrestore(&amd_lock, flags);
337 return;
338 }
339
340 if (disable) {
341 val &= ~0x08;
342 val |= (1 << 4) | (1 << 9);
343 } else {
344 val |= 0x08;
345 val &= ~((1 << 4) | (1 << 9));
346 }
347 outl_p(val, AB_DATA(addr));
348
349 if (!amd_chipset.nb_dev) {
350 spin_unlock_irqrestore(&amd_lock, flags);
351 return;
352 }
353
354 if (amd_chipset.nb_type == 1 || amd_chipset.nb_type == 3) {
355 addr = PCIE_P_CNTL;
356 pci_write_config_dword(amd_chipset.nb_dev,
357 NB_PCIE_INDX_ADDR, addr);
358 pci_read_config_dword(amd_chipset.nb_dev,
359 NB_PCIE_INDX_DATA, &val);
360
361 val &= ~(1 | (1 << 3) | (1 << 4) | (1 << 9) | (1 << 12));
362 val |= bit | (bit << 3) | (bit << 12);
363 val |= ((!bit) << 4) | ((!bit) << 9);
364 pci_write_config_dword(amd_chipset.nb_dev,
365 NB_PCIE_INDX_DATA, val);
366
367 addr = BIF_NB;
368 pci_write_config_dword(amd_chipset.nb_dev,
369 NB_PCIE_INDX_ADDR, addr);
370 pci_read_config_dword(amd_chipset.nb_dev,
371 NB_PCIE_INDX_DATA, &val);
372 val &= ~(1 << 8);
373 val |= bit << 8;
374
375 pci_write_config_dword(amd_chipset.nb_dev,
376 NB_PCIE_INDX_DATA, val);
377 } else if (amd_chipset.nb_type == 2) {
378 addr = NB_PIF0_PWRDOWN_0;
379 pci_write_config_dword(amd_chipset.nb_dev,
380 NB_PCIE_INDX_ADDR, addr);
381 pci_read_config_dword(amd_chipset.nb_dev,
382 NB_PCIE_INDX_DATA, &val);
383 if (disable)
384 val &= ~(0x3f << 7);
385 else
386 val |= 0x3f << 7;
387
388 pci_write_config_dword(amd_chipset.nb_dev,
389 NB_PCIE_INDX_DATA, val);
390
391 addr = NB_PIF0_PWRDOWN_1;
392 pci_write_config_dword(amd_chipset.nb_dev,
393 NB_PCIE_INDX_ADDR, addr);
394 pci_read_config_dword(amd_chipset.nb_dev,
395 NB_PCIE_INDX_DATA, &val);
396 if (disable)
397 val &= ~(0x3f << 7);
398 else
399 val |= 0x3f << 7;
400
401 pci_write_config_dword(amd_chipset.nb_dev,
402 NB_PCIE_INDX_DATA, val);
403 }
404
405 spin_unlock_irqrestore(&amd_lock, flags);
406 return;
407}
408
409void usb_amd_quirk_pll_disable(void)
410{
411 usb_amd_quirk_pll(1);
412}
413EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_disable);
414
415void usb_amd_quirk_pll_enable(void)
416{
417 usb_amd_quirk_pll(0);
418}
419EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_enable);
420
421void usb_amd_dev_put(void)
422{
423 struct pci_dev *nb, *smbus;
424 unsigned long flags;
425
426 spin_lock_irqsave(&amd_lock, flags);
427
428 amd_chipset.probe_count--;
429 if (amd_chipset.probe_count > 0) {
430 spin_unlock_irqrestore(&amd_lock, flags);
431 return;
432 }
433
434 /* save them to pci_dev_put outside of spinlock */
435 nb = amd_chipset.nb_dev;
436 smbus = amd_chipset.smbus_dev;
437
438 amd_chipset.nb_dev = NULL;
439 amd_chipset.smbus_dev = NULL;
440 amd_chipset.nb_type = 0;
441 memset(&amd_chipset.sb_type, 0, sizeof(amd_chipset.sb_type));
442 amd_chipset.isoc_reqs = 0;
443 amd_chipset.probe_result = 0;
444
445 spin_unlock_irqrestore(&amd_lock, flags);
446
447 pci_dev_put(nb);
448 pci_dev_put(smbus);
449}
450EXPORT_SYMBOL_GPL(usb_amd_dev_put);
451
452/*
453 * Make sure the controller is completely inactive, unable to
454 * generate interrupts or do DMA.
455 */
456void uhci_reset_hc(struct pci_dev *pdev, unsigned long base)
457{
458 /* Turn off PIRQ enable and SMI enable. (This also turns off the
459 * BIOS's USB Legacy Support.) Turn off all the R/WC bits too.
460 */
461 pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_RWC);
462
463 /* Reset the HC - this will force us to get a
464 * new notification of any already connected
465 * ports due to the virtual disconnect that it
466 * implies.
467 */
468 outw(UHCI_USBCMD_HCRESET, base + UHCI_USBCMD);
469 mb();
470 udelay(5);
471 if (inw(base + UHCI_USBCMD) & UHCI_USBCMD_HCRESET)
472 dev_warn(&pdev->dev, "HCRESET not completed yet!\n");
473
474 /* Just to be safe, disable interrupt requests and
475 * make sure the controller is stopped.
476 */
477 outw(0, base + UHCI_USBINTR);
478 outw(0, base + UHCI_USBCMD);
479}
480EXPORT_SYMBOL_GPL(uhci_reset_hc);
481
482/*
483 * Initialize a controller that was newly discovered or has just been
484 * resumed. In either case we can't be sure of its previous state.
485 *
486 * Returns: 1 if the controller was reset, 0 otherwise.
487 */
488int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base)
489{
490 u16 legsup;
491 unsigned int cmd, intr;
492
493 /*
494 * When restarting a suspended controller, we expect all the
495 * settings to be the same as we left them:
496 *
497 * PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
498 * Controller is stopped and configured with EGSM set;
499 * No interrupts enabled except possibly Resume Detect.
500 *
501 * If any of these conditions are violated we do a complete reset.
502 */
503 pci_read_config_word(pdev, UHCI_USBLEGSUP, &legsup);
504 if (legsup & ~(UHCI_USBLEGSUP_RO | UHCI_USBLEGSUP_RWC)) {
505 dev_dbg(&pdev->dev, "%s: legsup = 0x%04x\n",
506 __func__, legsup);
507 goto reset_needed;
508 }
509
510 cmd = inw(base + UHCI_USBCMD);
511 if ((cmd & UHCI_USBCMD_RUN) || !(cmd & UHCI_USBCMD_CONFIGURE) ||
512 !(cmd & UHCI_USBCMD_EGSM)) {
513 dev_dbg(&pdev->dev, "%s: cmd = 0x%04x\n",
514 __func__, cmd);
515 goto reset_needed;
516 }
517
518 intr = inw(base + UHCI_USBINTR);
519 if (intr & (~UHCI_USBINTR_RESUME)) {
520 dev_dbg(&pdev->dev, "%s: intr = 0x%04x\n",
521 __func__, intr);
522 goto reset_needed;
523 }
524 return 0;
525
526reset_needed:
527 dev_dbg(&pdev->dev, "Performing full reset\n");
528 uhci_reset_hc(pdev, base);
529 return 1;
530}
531EXPORT_SYMBOL_GPL(uhci_check_and_reset_hc);
532
533static inline int io_type_enabled(struct pci_dev *pdev, unsigned int mask)
534{
535 u16 cmd;
536 return !pci_read_config_word(pdev, PCI_COMMAND, &cmd) && (cmd & mask);
537}
538
539#define pio_enabled(dev) io_type_enabled(dev, PCI_COMMAND_IO)
540#define mmio_enabled(dev) io_type_enabled(dev, PCI_COMMAND_MEMORY)
541
542static void quirk_usb_handoff_uhci(struct pci_dev *pdev)
543{
544 unsigned long base = 0;
545 int i;
546
547 if (!pio_enabled(pdev))
548 return;
549
550 for (i = 0; i < PCI_ROM_RESOURCE; i++)
551 if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
552 base = pci_resource_start(pdev, i);
553 break;
554 }
555
556 if (base)
557 uhci_check_and_reset_hc(pdev, base);
558}
559
560static int mmio_resource_enabled(struct pci_dev *pdev, int idx)
561{
562 return pci_resource_start(pdev, idx) && mmio_enabled(pdev);
563}
564
565static void quirk_usb_handoff_ohci(struct pci_dev *pdev)
566{
567 void __iomem *base;
568 u32 control;
569 u32 fminterval = 0;
570 bool no_fminterval = false;
571 int cnt;
572
573 if (!mmio_resource_enabled(pdev, 0))
574 return;
575
576 base = pci_ioremap_bar(pdev, 0);
577 if (base == NULL)
578 return;
579
580 /*
581 * ULi M5237 OHCI controller locks the whole system when accessing
582 * the OHCI_FMINTERVAL offset.
583 */
584 if (pdev->vendor == PCI_VENDOR_ID_AL && pdev->device == 0x5237)
585 no_fminterval = true;
586
587 control = readl(base + OHCI_CONTROL);
588
589/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
590#ifdef __hppa__
591#define OHCI_CTRL_MASK (OHCI_CTRL_RWC | OHCI_CTRL_IR)
592#else
593#define OHCI_CTRL_MASK OHCI_CTRL_RWC
594
595 if (control & OHCI_CTRL_IR) {
596 int wait_time = 500; /* arbitrary; 5 seconds */
597 writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
598 writel(OHCI_OCR, base + OHCI_CMDSTATUS);
599 while (wait_time > 0 &&
600 readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
601 wait_time -= 10;
602 msleep(10);
603 }
604 if (wait_time <= 0)
605 dev_warn(&pdev->dev,
606 "OHCI: BIOS handoff failed (BIOS bug?) %08x\n",
607 readl(base + OHCI_CONTROL));
608 }
609#endif
610
611 /* disable interrupts */
612 writel((u32) ~0, base + OHCI_INTRDISABLE);
613
614 /* Reset the USB bus, if the controller isn't already in RESET */
615 if (control & OHCI_HCFS) {
616 /* Go into RESET, preserving RWC (and possibly IR) */
617 writel(control & OHCI_CTRL_MASK, base + OHCI_CONTROL);
618 readl(base + OHCI_CONTROL);
619
620 /* drive bus reset for at least 50 ms (7.1.7.5) */
621 msleep(50);
622 }
623
624 /* software reset of the controller, preserving HcFmInterval */
625 if (!no_fminterval)
626 fminterval = readl(base + OHCI_FMINTERVAL);
627
628 writel(OHCI_HCR, base + OHCI_CMDSTATUS);
629
630 /* reset requires max 10 us delay */
631 for (cnt = 30; cnt > 0; --cnt) { /* ... allow extra time */
632 if ((readl(base + OHCI_CMDSTATUS) & OHCI_HCR) == 0)
633 break;
634 udelay(1);
635 }
636
637 if (!no_fminterval)
638 writel(fminterval, base + OHCI_FMINTERVAL);
639
640 /* Now the controller is safely in SUSPEND and nothing can wake it up */
641 iounmap(base);
642}
643
644static const struct dmi_system_id ehci_dmi_nohandoff_table[] = {
645 {
646 /* Pegatron Lucid (ExoPC) */
647 .matches = {
648 DMI_MATCH(DMI_BOARD_NAME, "EXOPG06411"),
649 DMI_MATCH(DMI_BIOS_VERSION, "Lucid-CE-133"),
650 },
651 },
652 {
653 /* Pegatron Lucid (Ordissimo AIRIS) */
654 .matches = {
655 DMI_MATCH(DMI_BOARD_NAME, "M11JB"),
656 DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
657 },
658 },
659 {
660 /* Pegatron Lucid (Ordissimo) */
661 .matches = {
662 DMI_MATCH(DMI_BOARD_NAME, "Ordissimo"),
663 DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
664 },
665 },
666 {
667 /* HASEE E200 */
668 .matches = {
669 DMI_MATCH(DMI_BOARD_VENDOR, "HASEE"),
670 DMI_MATCH(DMI_BOARD_NAME, "E210"),
671 DMI_MATCH(DMI_BIOS_VERSION, "6.00"),
672 },
673 },
674 { }
675};
676
677static void ehci_bios_handoff(struct pci_dev *pdev,
678 void __iomem *op_reg_base,
679 u32 cap, u8 offset)
680{
681 int try_handoff = 1, tried_handoff = 0;
682
683 /*
684 * The Pegatron Lucid tablet sporadically waits for 98 seconds trying
685 * the handoff on its unused controller. Skip it.
686 *
687 * The HASEE E200 hangs when the semaphore is set (bugzilla #77021).
688 */
689 if (pdev->vendor == 0x8086 && (pdev->device == 0x283a ||
690 pdev->device == 0x27cc)) {
691 if (dmi_check_system(ehci_dmi_nohandoff_table))
692 try_handoff = 0;
693 }
694
695 if (try_handoff && (cap & EHCI_USBLEGSUP_BIOS)) {
696 dev_dbg(&pdev->dev, "EHCI: BIOS handoff\n");
697
698#if 0
699/* aleksey_gorelov@phoenix.com reports that some systems need SMI forced on,
700 * but that seems dubious in general (the BIOS left it off intentionally)
701 * and is known to prevent some systems from booting. so we won't do this
702 * unless maybe we can determine when we're on a system that needs SMI forced.
703 */
704 /* BIOS workaround (?): be sure the pre-Linux code
705 * receives the SMI
706 */
707 pci_read_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, &val);
708 pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS,
709 val | EHCI_USBLEGCTLSTS_SOOE);
710#endif
711
712 /* some systems get upset if this semaphore is
713 * set for any other reason than forcing a BIOS
714 * handoff..
715 */
716 pci_write_config_byte(pdev, offset + 3, 1);
717 }
718
719 /* if boot firmware now owns EHCI, spin till it hands it over. */
720 if (try_handoff) {
721 int msec = 1000;
722 while ((cap & EHCI_USBLEGSUP_BIOS) && (msec > 0)) {
723 tried_handoff = 1;
724 msleep(10);
725 msec -= 10;
726 pci_read_config_dword(pdev, offset, &cap);
727 }
728 }
729
730 if (cap & EHCI_USBLEGSUP_BIOS) {
731 /* well, possibly buggy BIOS... try to shut it down,
732 * and hope nothing goes too wrong
733 */
734 if (try_handoff)
735 dev_warn(&pdev->dev,
736 "EHCI: BIOS handoff failed (BIOS bug?) %08x\n",
737 cap);
738 pci_write_config_byte(pdev, offset + 2, 0);
739 }
740
741 /* just in case, always disable EHCI SMIs */
742 pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, 0);
743
744 /* If the BIOS ever owned the controller then we can't expect
745 * any power sessions to remain intact.
746 */
747 if (tried_handoff)
748 writel(0, op_reg_base + EHCI_CONFIGFLAG);
749}
750
751static void quirk_usb_disable_ehci(struct pci_dev *pdev)
752{
753 void __iomem *base, *op_reg_base;
754 u32 hcc_params, cap, val;
755 u8 offset, cap_length;
756 int wait_time, count = 256/4;
757
758 if (!mmio_resource_enabled(pdev, 0))
759 return;
760
761 base = pci_ioremap_bar(pdev, 0);
762 if (base == NULL)
763 return;
764
765 cap_length = readb(base);
766 op_reg_base = base + cap_length;
767
768 /* EHCI 0.96 and later may have "extended capabilities"
769 * spec section 5.1 explains the bios handoff, e.g. for
770 * booting from USB disk or using a usb keyboard
771 */
772 hcc_params = readl(base + EHCI_HCC_PARAMS);
773 offset = (hcc_params >> 8) & 0xff;
774 while (offset && --count) {
775 pci_read_config_dword(pdev, offset, &cap);
776
777 switch (cap & 0xff) {
778 case 1:
779 ehci_bios_handoff(pdev, op_reg_base, cap, offset);
780 break;
781 case 0: /* Illegal reserved cap, set cap=0 so we exit */
782 cap = 0; /* then fallthrough... */
783 default:
784 dev_warn(&pdev->dev,
785 "EHCI: unrecognized capability %02x\n",
786 cap & 0xff);
787 }
788 offset = (cap >> 8) & 0xff;
789 }
790 if (!count)
791 dev_printk(KERN_DEBUG, &pdev->dev, "EHCI: capability loop?\n");
792
793 /*
794 * halt EHCI & disable its interrupts in any case
795 */
796 val = readl(op_reg_base + EHCI_USBSTS);
797 if ((val & EHCI_USBSTS_HALTED) == 0) {
798 val = readl(op_reg_base + EHCI_USBCMD);
799 val &= ~EHCI_USBCMD_RUN;
800 writel(val, op_reg_base + EHCI_USBCMD);
801
802 wait_time = 2000;
803 do {
804 writel(0x3f, op_reg_base + EHCI_USBSTS);
805 udelay(100);
806 wait_time -= 100;
807 val = readl(op_reg_base + EHCI_USBSTS);
808 if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
809 break;
810 }
811 } while (wait_time > 0);
812 }
813 writel(0, op_reg_base + EHCI_USBINTR);
814 writel(0x3f, op_reg_base + EHCI_USBSTS);
815
816 iounmap(base);
817}
818
819/*
820 * handshake - spin reading a register until handshake completes
821 * @ptr: address of hc register to be read
822 * @mask: bits to look at in result of read
823 * @done: value of those bits when handshake succeeds
824 * @wait_usec: timeout in microseconds
825 * @delay_usec: delay in microseconds to wait between polling
826 *
827 * Polls a register every delay_usec microseconds.
828 * Returns 0 when the mask bits have the value done.
829 * Returns -ETIMEDOUT if this condition is not true after
830 * wait_usec microseconds have passed.
831 */
832static int handshake(void __iomem *ptr, u32 mask, u32 done,
833 int wait_usec, int delay_usec)
834{
835 u32 result;
836
837 do {
838 result = readl(ptr);
839 result &= mask;
840 if (result == done)
841 return 0;
842 udelay(delay_usec);
843 wait_usec -= delay_usec;
844 } while (wait_usec > 0);
845 return -ETIMEDOUT;
846}
847
848/*
849 * Intel's Panther Point chipset has two host controllers (EHCI and xHCI) that
850 * share some number of ports. These ports can be switched between either
851 * controller. Not all of the ports under the EHCI host controller may be
852 * switchable.
853 *
854 * The ports should be switched over to xHCI before PCI probes for any device
855 * start. This avoids active devices under EHCI being disconnected during the
856 * port switchover, which could cause loss of data on USB storage devices, or
857 * failed boot when the root file system is on a USB mass storage device and is
858 * enumerated under EHCI first.
859 *
860 * We write into the xHC's PCI configuration space in some Intel-specific
861 * registers to switch the ports over. The USB 3.0 terminations and the USB
862 * 2.0 data wires are switched separately. We want to enable the SuperSpeed
863 * terminations before switching the USB 2.0 wires over, so that USB 3.0
864 * devices connect at SuperSpeed, rather than at USB 2.0 speeds.
865 */
866void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
867{
868 u32 ports_available;
869 bool ehci_found = false;
870 struct pci_dev *companion = NULL;
871
872 /* Sony VAIO t-series with subsystem device ID 90a8 is not capable of
873 * switching ports from EHCI to xHCI
874 */
875 if (xhci_pdev->subsystem_vendor == PCI_VENDOR_ID_SONY &&
876 xhci_pdev->subsystem_device == 0x90a8)
877 return;
878
879 /* make sure an intel EHCI controller exists */
880 for_each_pci_dev(companion) {
881 if (companion->class == PCI_CLASS_SERIAL_USB_EHCI &&
882 companion->vendor == PCI_VENDOR_ID_INTEL) {
883 ehci_found = true;
884 break;
885 }
886 }
887
888 if (!ehci_found)
889 return;
890
891 /* Don't switchover the ports if the user hasn't compiled the xHCI
892 * driver. Otherwise they will see "dead" USB ports that don't power
893 * the devices.
894 */
895 if (!IS_ENABLED(CONFIG_USB_XHCI_HCD)) {
896 dev_warn(&xhci_pdev->dev,
897 "CONFIG_USB_XHCI_HCD is turned off, defaulting to EHCI.\n");
898 dev_warn(&xhci_pdev->dev,
899 "USB 3.0 devices will work at USB 2.0 speeds.\n");
900 usb_disable_xhci_ports(xhci_pdev);
901 return;
902 }
903
904 /* Read USB3PRM, the USB 3.0 Port Routing Mask Register
905 * Indicate the ports that can be changed from OS.
906 */
907 pci_read_config_dword(xhci_pdev, USB_INTEL_USB3PRM,
908 &ports_available);
909
910 dev_dbg(&xhci_pdev->dev, "Configurable ports to enable SuperSpeed: 0x%x\n",
911 ports_available);
912
913 /* Write USB3_PSSEN, the USB 3.0 Port SuperSpeed Enable
914 * Register, to turn on SuperSpeed terminations for the
915 * switchable ports.
916 */
917 pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
918 ports_available);
919
920 pci_read_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
921 &ports_available);
922 dev_dbg(&xhci_pdev->dev,
923 "USB 3.0 ports that are now enabled under xHCI: 0x%x\n",
924 ports_available);
925
926 /* Read XUSB2PRM, xHCI USB 2.0 Port Routing Mask Register
927 * Indicate the USB 2.0 ports to be controlled by the xHCI host.
928 */
929
930 pci_read_config_dword(xhci_pdev, USB_INTEL_USB2PRM,
931 &ports_available);
932
933 dev_dbg(&xhci_pdev->dev, "Configurable USB 2.0 ports to hand over to xCHI: 0x%x\n",
934 ports_available);
935
936 /* Write XUSB2PR, the xHC USB 2.0 Port Routing Register, to
937 * switch the USB 2.0 power and data lines over to the xHCI
938 * host.
939 */
940 pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
941 ports_available);
942
943 pci_read_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
944 &ports_available);
945 dev_dbg(&xhci_pdev->dev,
946 "USB 2.0 ports that are now switched over to xHCI: 0x%x\n",
947 ports_available);
948}
949EXPORT_SYMBOL_GPL(usb_enable_intel_xhci_ports);
950
951void usb_disable_xhci_ports(struct pci_dev *xhci_pdev)
952{
953 pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN, 0x0);
954 pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR, 0x0);
955}
956EXPORT_SYMBOL_GPL(usb_disable_xhci_ports);
957
958/**
959 * PCI Quirks for xHCI.
960 *
961 * Takes care of the handoff between the Pre-OS (i.e. BIOS) and the OS.
962 * It signals to the BIOS that the OS wants control of the host controller,
963 * and then waits 5 seconds for the BIOS to hand over control.
964 * If we timeout, assume the BIOS is broken and take control anyway.
965 */
966static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
967{
968 void __iomem *base;
969 int ext_cap_offset;
970 void __iomem *op_reg_base;
971 u32 val;
972 int timeout;
973 int len = pci_resource_len(pdev, 0);
974
975 if (!mmio_resource_enabled(pdev, 0))
976 return;
977
978 base = ioremap_nocache(pci_resource_start(pdev, 0), len);
979 if (base == NULL)
980 return;
981
982 /*
983 * Find the Legacy Support Capability register -
984 * this is optional for xHCI host controllers.
985 */
986 ext_cap_offset = xhci_find_next_ext_cap(base, 0, XHCI_EXT_CAPS_LEGACY);
987
988 if (!ext_cap_offset)
989 goto hc_init;
990
991 if ((ext_cap_offset + sizeof(val)) > len) {
992 /* We're reading garbage from the controller */
993 dev_warn(&pdev->dev, "xHCI controller failing to respond");
994 goto iounmap;
995 }
996 val = readl(base + ext_cap_offset);
997
998 /* Auto handoff never worked for these devices. Force it and continue */
999 if ((pdev->vendor == PCI_VENDOR_ID_TI && pdev->device == 0x8241) ||
1000 (pdev->vendor == PCI_VENDOR_ID_RENESAS
1001 && pdev->device == 0x0014)) {
1002 val = (val | XHCI_HC_OS_OWNED) & ~XHCI_HC_BIOS_OWNED;
1003 writel(val, base + ext_cap_offset);
1004 }
1005
1006 /* If the BIOS owns the HC, signal that the OS wants it, and wait */
1007 if (val & XHCI_HC_BIOS_OWNED) {
1008 writel(val | XHCI_HC_OS_OWNED, base + ext_cap_offset);
1009
1010 /* Wait for 5 seconds with 10 microsecond polling interval */
1011 timeout = handshake(base + ext_cap_offset, XHCI_HC_BIOS_OWNED,
1012 0, 5000, 10);
1013
1014 /* Assume a buggy BIOS and take HC ownership anyway */
1015 if (timeout) {
1016 dev_warn(&pdev->dev,
1017 "xHCI BIOS handoff failed (BIOS bug ?) %08x\n",
1018 val);
1019 writel(val & ~XHCI_HC_BIOS_OWNED, base + ext_cap_offset);
1020 }
1021 }
1022
1023 val = readl(base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
1024 /* Mask off (turn off) any enabled SMIs */
1025 val &= XHCI_LEGACY_DISABLE_SMI;
1026 /* Mask all SMI events bits, RW1C */
1027 val |= XHCI_LEGACY_SMI_EVENTS;
1028 /* Disable any BIOS SMIs and clear all SMI events*/
1029 writel(val, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
1030
1031hc_init:
1032 if (pdev->vendor == PCI_VENDOR_ID_INTEL)
1033 usb_enable_intel_xhci_ports(pdev);
1034
1035 op_reg_base = base + XHCI_HC_LENGTH(readl(base));
1036
1037 /* Wait for the host controller to be ready before writing any
1038 * operational or runtime registers. Wait 5 seconds and no more.
1039 */
1040 timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_CNR, 0,
1041 5000, 10);
1042 /* Assume a buggy HC and start HC initialization anyway */
1043 if (timeout) {
1044 val = readl(op_reg_base + XHCI_STS_OFFSET);
1045 dev_warn(&pdev->dev,
1046 "xHCI HW not ready after 5 sec (HC bug?) status = 0x%x\n",
1047 val);
1048 }
1049
1050 /* Send the halt and disable interrupts command */
1051 val = readl(op_reg_base + XHCI_CMD_OFFSET);
1052 val &= ~(XHCI_CMD_RUN | XHCI_IRQS);
1053 writel(val, op_reg_base + XHCI_CMD_OFFSET);
1054
1055 /* Wait for the HC to halt - poll every 125 usec (one microframe). */
1056 timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_HALT, 1,
1057 XHCI_MAX_HALT_USEC, 125);
1058 if (timeout) {
1059 val = readl(op_reg_base + XHCI_STS_OFFSET);
1060 dev_warn(&pdev->dev,
1061 "xHCI HW did not halt within %d usec status = 0x%x\n",
1062 XHCI_MAX_HALT_USEC, val);
1063 }
1064
1065iounmap:
1066 iounmap(base);
1067}
1068
1069static void quirk_usb_early_handoff(struct pci_dev *pdev)
1070{
1071 /* Skip Netlogic mips SoC's internal PCI USB controller.
1072 * This device does not need/support EHCI/OHCI handoff
1073 */
1074 if (pdev->vendor == 0x184e) /* vendor Netlogic */
1075 return;
1076 if (pdev->class != PCI_CLASS_SERIAL_USB_UHCI &&
1077 pdev->class != PCI_CLASS_SERIAL_USB_OHCI &&
1078 pdev->class != PCI_CLASS_SERIAL_USB_EHCI &&
1079 pdev->class != PCI_CLASS_SERIAL_USB_XHCI)
1080 return;
1081
1082 if (pci_enable_device(pdev) < 0) {
1083 dev_warn(&pdev->dev,
1084 "Can't enable PCI device, BIOS handoff failed.\n");
1085 return;
1086 }
1087 if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
1088 quirk_usb_handoff_uhci(pdev);
1089 else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
1090 quirk_usb_handoff_ohci(pdev);
1091 else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
1092 quirk_usb_disable_ehci(pdev);
1093 else if (pdev->class == PCI_CLASS_SERIAL_USB_XHCI)
1094 quirk_usb_handoff_xhci(pdev);
1095 pci_disable_device(pdev);
1096}
1097DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
1098 PCI_CLASS_SERIAL_USB, 8, quirk_usb_early_handoff);