# SPDX-License-Identifier: GPL-2.0
#
# Makefile for the Linux kernel device drivers.
#
# 15 Sep 2000, Christoph Hellwig <hch@infradead.org>
# Rewritten to use lists instead of if-statements.
#

# Some driver Makefiles miss $(srctree)/ for include directive.
ifdef building_out_of_srctree
MAKEFLAGS += --include-dir=$(srctree)
endif

obj-y				+= cache
obj-y				+= irqchip
obj-y				+= bus

obj-$(CONFIG_GENERIC_PHY)	+= phy

# GPIO must come after pinctrl as gpios may need to mux pins etc
obj-$(CONFIG_PINCTRL)		+= pinctrl
obj-$(CONFIG_GPIOLIB)		+= gpio
obj-y				+= pwm

obj-y				+= pci

obj-$(CONFIG_PARISC)		+= parisc
obj-$(CONFIG_RAPIDIO)		+= rapidio
obj-y				+= video
obj-y				+= idle

# IPMI must come before ACPI in order to provide IPMI opregion support
obj-y				+= char/ipmi

obj-$(CONFIG_ACPI)		+= acpi

# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP)		+= pnp
obj-y				+= amba

obj-y				+= clk
# Many drivers will want to use DMA so this has to be made available
# really early.
obj-$(CONFIG_DMADEVICES)	+= dma

# SOC specific infrastructure drivers.
obj-y				+= soc
obj-$(CONFIG_PM_GENERIC_DOMAINS)	+= pmdomain

obj-y				+= virtio
obj-$(CONFIG_VDPA)		+= vdpa
obj-$(CONFIG_XEN)		+= xen

# regulators early, since some subsystems rely on them to initialize
obj-$(CONFIG_REGULATOR)		+= regulator

# reset controllers early, since gpu drivers might rely on them to initialize
obj-$(CONFIG_RESET_CONTROLLER)	+= reset

# tty comes before char so that the VT console is the boot-time
# default.
obj-y				+= tty
obj-y				+= char

# iommu comes before gpu as gpu are using iommu controllers
obj-y				+= iommu

# gpu comes after char for AGP vs DRM startup and after iommu
obj-y				+= gpu

obj-$(CONFIG_CONNECTOR)		+= connector

# i810fb depends on char/agp
obj-$(CONFIG_FB_I810)           += video/fbdev/i810

obj-$(CONFIG_PARPORT)		+= parport
obj-y				+= base block misc mfd nfc
obj-$(CONFIG_LIBNVDIMM)		+= nvdimm
obj-y				+= dax
obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf
obj-$(CONFIG_NUBUS)		+= nubus
obj-y				+= cxl
obj-y				+= macintosh
obj-y				+= scsi
obj-y				+= nvme
obj-$(CONFIG_ATA)		+= ata
obj-$(CONFIG_TARGET_CORE)	+= target
obj-$(CONFIG_MTD)		+= mtd
obj-$(CONFIG_SPI)		+= spi
obj-$(CONFIG_SPMI)		+= spmi
obj-$(CONFIG_HSI)		+= hsi
obj-$(CONFIG_SLIMBUS)		+= slimbus
obj-y				+= net
obj-$(CONFIG_ATM)		+= atm
obj-$(CONFIG_FUSION)		+= message
obj-y				+= firewire
obj-$(CONFIG_UIO)		+= uio
obj-$(CONFIG_VFIO)		+= vfio
obj-y				+= cdrom
obj-y				+= auxdisplay
obj-$(CONFIG_PCCARD)		+= pcmcia
obj-$(CONFIG_DIO)		+= dio
obj-$(CONFIG_SBUS)		+= sbus
obj-$(CONFIG_ZORRO)		+= zorro
obj-$(CONFIG_ATA_OVER_ETH)	+= block/aoe
obj-$(CONFIG_TC)		+= tc
obj-$(CONFIG_USB_PHY)		+= usb
obj-$(CONFIG_USB)		+= usb
obj-$(CONFIG_USB_SUPPORT)	+= usb
obj-$(CONFIG_PCI)		+= usb
obj-$(CONFIG_USB_GADGET)	+= usb
obj-$(CONFIG_OF)		+= usb
obj-$(CONFIG_SERIO)		+= input/serio
obj-$(CONFIG_GAMEPORT)		+= input/gameport
obj-$(CONFIG_INPUT)		+= input
obj-$(CONFIG_RTC_LIB)		+= rtc
obj-y				+= i2c i3c media
obj-$(CONFIG_PPS)		+= pps
obj-y				+= ptp
obj-$(CONFIG_W1)		+= w1
obj-y				+= power
obj-$(CONFIG_HWMON)		+= hwmon
obj-$(CONFIG_THERMAL)		+= thermal
obj-$(CONFIG_WATCHDOG)		+= watchdog
obj-$(CONFIG_MD)		+= md
obj-$(CONFIG_BT)		+= bluetooth
obj-$(CONFIG_ACCESSIBILITY)	+= accessibility
obj-$(CONFIG_ISDN)		+= isdn
obj-$(CONFIG_EDAC)		+= edac
obj-$(CONFIG_EISA)		+= eisa
obj-$(CONFIG_PM_OPP)		+= opp
obj-$(CONFIG_CPU_FREQ)		+= cpufreq
obj-$(CONFIG_CPU_IDLE)		+= cpuidle
obj-y				+= mmc
obj-y				+= ufs
obj-$(CONFIG_MEMSTICK)		+= memstick
obj-$(CONFIG_NEW_LEDS)		+= leds
obj-$(CONFIG_INFINIBAND)	+= infiniband
obj-y				+= firmware
obj-$(CONFIG_CRYPTO)		+= crypto
obj-$(CONFIG_SUPERH)		+= sh
obj-y				+= clocksource
obj-$(CONFIG_DCA)		+= dca
obj-$(CONFIG_HID_SUPPORT)	+= hid
obj-$(CONFIG_PPC_PS3)		+= ps3
obj-$(CONFIG_OF)		+= of
obj-$(CONFIG_SSB)		+= ssb
obj-$(CONFIG_BCMA)		+= bcma
obj-$(CONFIG_VHOST_RING)	+= vhost
obj-$(CONFIG_VHOST_IOTLB)	+= vhost
obj-$(CONFIG_VHOST)		+= vhost
obj-$(CONFIG_GREYBUS)		+= greybus
obj-$(CONFIG_COMEDI)		+= comedi
obj-$(CONFIG_STAGING)		+= staging
obj-y				+= platform

obj-$(CONFIG_MAILBOX)		+= mailbox
obj-$(CONFIG_HWSPINLOCK)	+= hwspinlock
obj-$(CONFIG_REMOTEPROC)	+= remoteproc
obj-$(CONFIG_RPMSG)		+= rpmsg
obj-$(CONFIG_SOUNDWIRE)		+= soundwire

# Virtualization drivers
obj-$(CONFIG_VIRT_DRIVERS)	+= virt
obj-$(subst m,y,$(CONFIG_HYPERV))	+= hv

obj-$(CONFIG_PM_DEVFREQ)	+= devfreq
obj-$(CONFIG_EXTCON)		+= extcon
obj-$(CONFIG_MEMORY)		+= memory
obj-$(CONFIG_IIO)		+= iio
obj-$(CONFIG_IPACK_BUS)		+= ipack
obj-$(CONFIG_NTB)		+= ntb
obj-$(CONFIG_POWERCAP)		+= powercap
obj-$(CONFIG_MCB)		+= mcb
obj-$(CONFIG_PERF_EVENTS)	+= perf
obj-$(CONFIG_RAS)		+= ras
obj-$(CONFIG_USB4)		+= thunderbolt
obj-$(CONFIG_CORESIGHT)		+= hwtracing/coresight
obj-y				+= hwtracing/intel_th
obj-$(CONFIG_STM)		+= hwtracing/stm
obj-$(CONFIG_HISI_PTT)		+= hwtracing/ptt
obj-y				+= android
obj-$(CONFIG_NVMEM)		+= nvmem
obj-$(CONFIG_FPGA)		+= fpga
obj-$(CONFIG_FSI)		+= fsi
obj-$(CONFIG_TEE)		+= tee
obj-$(CONFIG_MULTIPLEXER)	+= mux
obj-$(CONFIG_SIOX)		+= siox
obj-$(CONFIG_GNSS)		+= gnss
obj-$(CONFIG_INTERCONNECT)	+= interconnect
obj-$(CONFIG_COUNTER)		+= counter
obj-$(CONFIG_MOST)		+= most
obj-$(CONFIG_PECI)		+= peci
obj-$(CONFIG_HTE)		+= hte
obj-$(CONFIG_DRM_ACCEL)		+= accel
obj-$(CONFIG_CDX_BUS)		+= cdx
obj-$(CONFIG_DPLL)		+= dpll

obj-$(CONFIG_S390)		+= s390