Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Cadence UART driver (found in Xilinx Zynq)
4 *
5 * Copyright (c) 2011 - 2014 Xilinx, Inc.
6 *
7 * This driver has originally been pushed by Xilinx using a Zynq-branding. This
8 * still shows in the naming of this file, the kconfig symbols and some symbols
9 * in the code.
10 */
11
12#include <linux/platform_device.h>
13#include <linux/serial.h>
14#include <linux/console.h>
15#include <linux/serial_core.h>
16#include <linux/slab.h>
17#include <linux/tty.h>
18#include <linux/tty_flip.h>
19#include <linux/clk.h>
20#include <linux/irq.h>
21#include <linux/io.h>
22#include <linux/of.h>
23#include <linux/module.h>
24#include <linux/pm_runtime.h>
25#include <linux/iopoll.h>
26
27#define CDNS_UART_TTY_NAME "ttyPS"
28#define CDNS_UART_NAME "xuartps"
29#define CDNS_UART_MAJOR 0 /* use dynamic node allocation */
30#define CDNS_UART_MINOR 0 /* works best with devtmpfs */
31#define CDNS_UART_NR_PORTS 16
32#define CDNS_UART_FIFO_SIZE 64 /* FIFO size */
33#define CDNS_UART_REGISTER_SPACE 0x1000
34#define TX_TIMEOUT 500000
35
36/* Rx Trigger level */
37static int rx_trigger_level = 56;
38module_param(rx_trigger_level, uint, 0444);
39MODULE_PARM_DESC(rx_trigger_level, "Rx trigger level, 1-63 bytes");
40
41/* Rx Timeout */
42static int rx_timeout = 10;
43module_param(rx_timeout, uint, 0444);
44MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
45
46/* Register offsets for the UART. */
47#define CDNS_UART_CR 0x00 /* Control Register */
48#define CDNS_UART_MR 0x04 /* Mode Register */
49#define CDNS_UART_IER 0x08 /* Interrupt Enable */
50#define CDNS_UART_IDR 0x0C /* Interrupt Disable */
51#define CDNS_UART_IMR 0x10 /* Interrupt Mask */
52#define CDNS_UART_ISR 0x14 /* Interrupt Status */
53#define CDNS_UART_BAUDGEN 0x18 /* Baud Rate Generator */
54#define CDNS_UART_RXTOUT 0x1C /* RX Timeout */
55#define CDNS_UART_RXWM 0x20 /* RX FIFO Trigger Level */
56#define CDNS_UART_MODEMCR 0x24 /* Modem Control */
57#define CDNS_UART_MODEMSR 0x28 /* Modem Status */
58#define CDNS_UART_SR 0x2C /* Channel Status */
59#define CDNS_UART_FIFO 0x30 /* FIFO */
60#define CDNS_UART_BAUDDIV 0x34 /* Baud Rate Divider */
61#define CDNS_UART_FLOWDEL 0x38 /* Flow Delay */
62#define CDNS_UART_IRRX_PWIDTH 0x3C /* IR Min Received Pulse Width */
63#define CDNS_UART_IRTX_PWIDTH 0x40 /* IR Transmitted pulse Width */
64#define CDNS_UART_TXWM 0x44 /* TX FIFO Trigger Level */
65#define CDNS_UART_RXBS 0x48 /* RX FIFO byte status register */
66
67/* Control Register Bit Definitions */
68#define CDNS_UART_CR_STOPBRK 0x00000100 /* Stop TX break */
69#define CDNS_UART_CR_STARTBRK 0x00000080 /* Set TX break */
70#define CDNS_UART_CR_TX_DIS 0x00000020 /* TX disabled. */
71#define CDNS_UART_CR_TX_EN 0x00000010 /* TX enabled */
72#define CDNS_UART_CR_RX_DIS 0x00000008 /* RX disabled. */
73#define CDNS_UART_CR_RX_EN 0x00000004 /* RX enabled */
74#define CDNS_UART_CR_TXRST 0x00000002 /* TX logic reset */
75#define CDNS_UART_CR_RXRST 0x00000001 /* RX logic reset */
76#define CDNS_UART_CR_RST_TO 0x00000040 /* Restart Timeout Counter */
77#define CDNS_UART_RXBS_PARITY 0x00000001 /* Parity error status */
78#define CDNS_UART_RXBS_FRAMING 0x00000002 /* Framing error status */
79#define CDNS_UART_RXBS_BRK 0x00000004 /* Overrun error status */
80
81/*
82 * Mode Register:
83 * The mode register (MR) defines the mode of transfer as well as the data
84 * format. If this register is modified during transmission or reception,
85 * data validity cannot be guaranteed.
86 */
87#define CDNS_UART_MR_CLKSEL 0x00000001 /* Pre-scalar selection */
88#define CDNS_UART_MR_CHMODE_L_LOOP 0x00000200 /* Local loop back mode */
89#define CDNS_UART_MR_CHMODE_NORM 0x00000000 /* Normal mode */
90#define CDNS_UART_MR_CHMODE_MASK 0x00000300 /* Mask for mode bits */
91
92#define CDNS_UART_MR_STOPMODE_2_BIT 0x00000080 /* 2 stop bits */
93#define CDNS_UART_MR_STOPMODE_1_BIT 0x00000000 /* 1 stop bit */
94
95#define CDNS_UART_MR_PARITY_NONE 0x00000020 /* No parity mode */
96#define CDNS_UART_MR_PARITY_MARK 0x00000018 /* Mark parity mode */
97#define CDNS_UART_MR_PARITY_SPACE 0x00000010 /* Space parity mode */
98#define CDNS_UART_MR_PARITY_ODD 0x00000008 /* Odd parity mode */
99#define CDNS_UART_MR_PARITY_EVEN 0x00000000 /* Even parity mode */
100
101#define CDNS_UART_MR_CHARLEN_6_BIT 0x00000006 /* 6 bits data */
102#define CDNS_UART_MR_CHARLEN_7_BIT 0x00000004 /* 7 bits data */
103#define CDNS_UART_MR_CHARLEN_8_BIT 0x00000000 /* 8 bits data */
104
105/*
106 * Interrupt Registers:
107 * Interrupt control logic uses the interrupt enable register (IER) and the
108 * interrupt disable register (IDR) to set the value of the bits in the
109 * interrupt mask register (IMR). The IMR determines whether to pass an
110 * interrupt to the interrupt status register (ISR).
111 * Writing a 1 to IER Enables an interrupt, writing a 1 to IDR disables an
112 * interrupt. IMR and ISR are read only, and IER and IDR are write only.
113 * Reading either IER or IDR returns 0x00.
114 * All four registers have the same bit definitions.
115 */
116#define CDNS_UART_IXR_TOUT 0x00000100 /* RX Timeout error interrupt */
117#define CDNS_UART_IXR_PARITY 0x00000080 /* Parity error interrupt */
118#define CDNS_UART_IXR_FRAMING 0x00000040 /* Framing error interrupt */
119#define CDNS_UART_IXR_OVERRUN 0x00000020 /* Overrun error interrupt */
120#define CDNS_UART_IXR_TXFULL 0x00000010 /* TX FIFO Full interrupt */
121#define CDNS_UART_IXR_TXEMPTY 0x00000008 /* TX FIFO empty interrupt */
122#define CDNS_UART_ISR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt */
123#define CDNS_UART_IXR_RXTRIG 0x00000001 /* RX FIFO trigger interrupt */
124#define CDNS_UART_IXR_RXFULL 0x00000004 /* RX FIFO full interrupt. */
125#define CDNS_UART_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
126#define CDNS_UART_IXR_RXMASK 0x000021e7 /* Valid RX bit mask */
127
128 /*
129 * Do not enable parity error interrupt for the following
130 * reason: When parity error interrupt is enabled, each Rx
131 * parity error always results in 2 events. The first one
132 * being parity error interrupt and the second one with a
133 * proper Rx interrupt with the incoming data. Disabling
134 * parity error interrupt ensures better handling of parity
135 * error events. With this change, for a parity error case, we
136 * get a Rx interrupt with parity error set in ISR register
137 * and we still handle parity errors in the desired way.
138 */
139
140#define CDNS_UART_RX_IRQS (CDNS_UART_IXR_FRAMING | \
141 CDNS_UART_IXR_OVERRUN | \
142 CDNS_UART_IXR_RXTRIG | \
143 CDNS_UART_IXR_TOUT)
144
145/* Goes in read_status_mask for break detection as the HW doesn't do it*/
146#define CDNS_UART_IXR_BRK 0x00002000
147
148#define CDNS_UART_RXBS_SUPPORT BIT(1)
149/*
150 * Modem Control register:
151 * The read/write Modem Control register controls the interface with the modem
152 * or data set, or a peripheral device emulating a modem.
153 */
154#define CDNS_UART_MODEMCR_FCM 0x00000020 /* Automatic flow control mode */
155#define CDNS_UART_MODEMCR_RTS 0x00000002 /* Request to send output control */
156#define CDNS_UART_MODEMCR_DTR 0x00000001 /* Data Terminal Ready */
157
158/*
159 * Modem Status register:
160 * The read/write Modem Status register reports the interface with the modem
161 * or data set, or a peripheral device emulating a modem.
162 */
163#define CDNS_UART_MODEMSR_DCD BIT(7) /* Data Carrier Detect */
164#define CDNS_UART_MODEMSR_RI BIT(6) /* Ting Indicator */
165#define CDNS_UART_MODEMSR_DSR BIT(5) /* Data Set Ready */
166#define CDNS_UART_MODEMSR_CTS BIT(4) /* Clear To Send */
167
168/*
169 * Channel Status Register:
170 * The channel status register (CSR) is provided to enable the control logic
171 * to monitor the status of bits in the channel interrupt status register,
172 * even if these are masked out by the interrupt mask register.
173 */
174#define CDNS_UART_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
175#define CDNS_UART_SR_TXEMPTY 0x00000008 /* TX FIFO empty */
176#define CDNS_UART_SR_TXFULL 0x00000010 /* TX FIFO full */
177#define CDNS_UART_SR_RXTRIG 0x00000001 /* Rx Trigger */
178#define CDNS_UART_SR_TACTIVE 0x00000800 /* TX state machine active */
179
180/* baud dividers min/max values */
181#define CDNS_UART_BDIV_MIN 4
182#define CDNS_UART_BDIV_MAX 255
183#define CDNS_UART_CD_MAX 65535
184#define UART_AUTOSUSPEND_TIMEOUT 3000
185
186/**
187 * struct cdns_uart - device data
188 * @port: Pointer to the UART port
189 * @uartclk: Reference clock
190 * @pclk: APB clock
191 * @cdns_uart_driver: Pointer to UART driver
192 * @baud: Current baud rate
193 * @clk_rate_change_nb: Notifier block for clock changes
194 * @quirks: Flags for RXBS support.
195 * @cts_override: Modem control state override
196 */
197struct cdns_uart {
198 struct uart_port *port;
199 struct clk *uartclk;
200 struct clk *pclk;
201 struct uart_driver *cdns_uart_driver;
202 unsigned int baud;
203 struct notifier_block clk_rate_change_nb;
204 u32 quirks;
205 bool cts_override;
206};
207struct cdns_platform_data {
208 u32 quirks;
209};
210#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
211 clk_rate_change_nb)
212
213/**
214 * cdns_uart_handle_rx - Handle the received bytes along with Rx errors.
215 * @dev_id: Id of the UART port
216 * @isrstatus: The interrupt status register value as read
217 * Return: None
218 */
219static void cdns_uart_handle_rx(void *dev_id, unsigned int isrstatus)
220{
221 struct uart_port *port = (struct uart_port *)dev_id;
222 struct cdns_uart *cdns_uart = port->private_data;
223 unsigned int data;
224 unsigned int rxbs_status = 0;
225 unsigned int status_mask;
226 unsigned int framerrprocessed = 0;
227 char status = TTY_NORMAL;
228 bool is_rxbs_support;
229
230 is_rxbs_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
231
232 while ((readl(port->membase + CDNS_UART_SR) &
233 CDNS_UART_SR_RXEMPTY) != CDNS_UART_SR_RXEMPTY) {
234 if (is_rxbs_support)
235 rxbs_status = readl(port->membase + CDNS_UART_RXBS);
236 data = readl(port->membase + CDNS_UART_FIFO);
237 port->icount.rx++;
238 /*
239 * There is no hardware break detection in Zynq, so we interpret
240 * framing error with all-zeros data as a break sequence.
241 * Most of the time, there's another non-zero byte at the
242 * end of the sequence.
243 */
244 if (!is_rxbs_support && (isrstatus & CDNS_UART_IXR_FRAMING)) {
245 if (!data) {
246 port->read_status_mask |= CDNS_UART_IXR_BRK;
247 framerrprocessed = 1;
248 continue;
249 }
250 }
251 if (is_rxbs_support && (rxbs_status & CDNS_UART_RXBS_BRK)) {
252 port->icount.brk++;
253 status = TTY_BREAK;
254 if (uart_handle_break(port))
255 continue;
256 }
257
258 isrstatus &= port->read_status_mask;
259 isrstatus &= ~port->ignore_status_mask;
260 status_mask = port->read_status_mask;
261 status_mask &= ~port->ignore_status_mask;
262
263 if (data &&
264 (port->read_status_mask & CDNS_UART_IXR_BRK)) {
265 port->read_status_mask &= ~CDNS_UART_IXR_BRK;
266 port->icount.brk++;
267 if (uart_handle_break(port))
268 continue;
269 }
270
271 if (uart_handle_sysrq_char(port, data))
272 continue;
273
274 if (is_rxbs_support) {
275 if ((rxbs_status & CDNS_UART_RXBS_PARITY)
276 && (status_mask & CDNS_UART_IXR_PARITY)) {
277 port->icount.parity++;
278 status = TTY_PARITY;
279 }
280 if ((rxbs_status & CDNS_UART_RXBS_FRAMING)
281 && (status_mask & CDNS_UART_IXR_PARITY)) {
282 port->icount.frame++;
283 status = TTY_FRAME;
284 }
285 } else {
286 if (isrstatus & CDNS_UART_IXR_PARITY) {
287 port->icount.parity++;
288 status = TTY_PARITY;
289 }
290 if ((isrstatus & CDNS_UART_IXR_FRAMING) &&
291 !framerrprocessed) {
292 port->icount.frame++;
293 status = TTY_FRAME;
294 }
295 }
296 if (isrstatus & CDNS_UART_IXR_OVERRUN) {
297 port->icount.overrun++;
298 tty_insert_flip_char(&port->state->port, 0,
299 TTY_OVERRUN);
300 }
301 tty_insert_flip_char(&port->state->port, data, status);
302 isrstatus = 0;
303 }
304
305 tty_flip_buffer_push(&port->state->port);
306}
307
308/**
309 * cdns_uart_handle_tx - Handle the bytes to be Txed.
310 * @dev_id: Id of the UART port
311 * Return: None
312 */
313static void cdns_uart_handle_tx(void *dev_id)
314{
315 struct uart_port *port = (struct uart_port *)dev_id;
316 struct circ_buf *xmit = &port->state->xmit;
317 unsigned int numbytes;
318
319 if (uart_circ_empty(xmit)) {
320 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IDR);
321 return;
322 }
323
324 numbytes = port->fifosize;
325 while (numbytes && !uart_circ_empty(xmit) &&
326 !(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)) {
327
328 writel(xmit->buf[xmit->tail], port->membase + CDNS_UART_FIFO);
329 uart_xmit_advance(port, 1);
330 numbytes--;
331 }
332
333 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
334 uart_write_wakeup(port);
335}
336
337/**
338 * cdns_uart_isr - Interrupt handler
339 * @irq: Irq number
340 * @dev_id: Id of the port
341 *
342 * Return: IRQHANDLED
343 */
344static irqreturn_t cdns_uart_isr(int irq, void *dev_id)
345{
346 struct uart_port *port = (struct uart_port *)dev_id;
347 unsigned int isrstatus;
348
349 uart_port_lock(port);
350
351 /* Read the interrupt status register to determine which
352 * interrupt(s) is/are active and clear them.
353 */
354 isrstatus = readl(port->membase + CDNS_UART_ISR);
355 writel(isrstatus, port->membase + CDNS_UART_ISR);
356
357 if (isrstatus & CDNS_UART_IXR_TXEMPTY) {
358 cdns_uart_handle_tx(dev_id);
359 isrstatus &= ~CDNS_UART_IXR_TXEMPTY;
360 }
361
362 isrstatus &= port->read_status_mask;
363 isrstatus &= ~port->ignore_status_mask;
364 /*
365 * Skip RX processing if RX is disabled as RXEMPTY will never be set
366 * as read bytes will not be removed from the FIFO.
367 */
368 if (isrstatus & CDNS_UART_IXR_RXMASK &&
369 !(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_RX_DIS))
370 cdns_uart_handle_rx(dev_id, isrstatus);
371
372 uart_port_unlock(port);
373 return IRQ_HANDLED;
374}
375
376/**
377 * cdns_uart_calc_baud_divs - Calculate baud rate divisors
378 * @clk: UART module input clock
379 * @baud: Desired baud rate
380 * @rbdiv: BDIV value (return value)
381 * @rcd: CD value (return value)
382 * @div8: Value for clk_sel bit in mod (return value)
383 * Return: baud rate, requested baud when possible, or actual baud when there
384 * was too much error, zero if no valid divisors are found.
385 *
386 * Formula to obtain baud rate is
387 * baud_tx/rx rate = clk/CD * (BDIV + 1)
388 * input_clk = (Uart User Defined Clock or Apb Clock)
389 * depends on UCLKEN in MR Reg
390 * clk = input_clk or input_clk/8;
391 * depends on CLKS in MR reg
392 * CD and BDIV depends on values in
393 * baud rate generate register
394 * baud rate clock divisor register
395 */
396static unsigned int cdns_uart_calc_baud_divs(unsigned int clk,
397 unsigned int baud, u32 *rbdiv, u32 *rcd, int *div8)
398{
399 u32 cd, bdiv;
400 unsigned int calc_baud;
401 unsigned int bestbaud = 0;
402 unsigned int bauderror;
403 unsigned int besterror = ~0;
404
405 if (baud < clk / ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX)) {
406 *div8 = 1;
407 clk /= 8;
408 } else {
409 *div8 = 0;
410 }
411
412 for (bdiv = CDNS_UART_BDIV_MIN; bdiv <= CDNS_UART_BDIV_MAX; bdiv++) {
413 cd = DIV_ROUND_CLOSEST(clk, baud * (bdiv + 1));
414 if (cd < 1 || cd > CDNS_UART_CD_MAX)
415 continue;
416
417 calc_baud = clk / (cd * (bdiv + 1));
418
419 if (baud > calc_baud)
420 bauderror = baud - calc_baud;
421 else
422 bauderror = calc_baud - baud;
423
424 if (besterror > bauderror) {
425 *rbdiv = bdiv;
426 *rcd = cd;
427 bestbaud = calc_baud;
428 besterror = bauderror;
429 }
430 }
431 /* use the values when percent error is acceptable */
432 if (((besterror * 100) / baud) < 3)
433 bestbaud = baud;
434
435 return bestbaud;
436}
437
438/**
439 * cdns_uart_set_baud_rate - Calculate and set the baud rate
440 * @port: Handle to the uart port structure
441 * @baud: Baud rate to set
442 * Return: baud rate, requested baud when possible, or actual baud when there
443 * was too much error, zero if no valid divisors are found.
444 */
445static unsigned int cdns_uart_set_baud_rate(struct uart_port *port,
446 unsigned int baud)
447{
448 unsigned int calc_baud;
449 u32 cd = 0, bdiv = 0;
450 u32 mreg;
451 int div8;
452 struct cdns_uart *cdns_uart = port->private_data;
453
454 calc_baud = cdns_uart_calc_baud_divs(port->uartclk, baud, &bdiv, &cd,
455 &div8);
456
457 /* Write new divisors to hardware */
458 mreg = readl(port->membase + CDNS_UART_MR);
459 if (div8)
460 mreg |= CDNS_UART_MR_CLKSEL;
461 else
462 mreg &= ~CDNS_UART_MR_CLKSEL;
463 writel(mreg, port->membase + CDNS_UART_MR);
464 writel(cd, port->membase + CDNS_UART_BAUDGEN);
465 writel(bdiv, port->membase + CDNS_UART_BAUDDIV);
466 cdns_uart->baud = baud;
467
468 return calc_baud;
469}
470
471#ifdef CONFIG_COMMON_CLK
472/**
473 * cdns_uart_clk_notifier_cb - Clock notifier callback
474 * @nb: Notifier block
475 * @event: Notify event
476 * @data: Notifier data
477 * Return: NOTIFY_OK or NOTIFY_DONE on success, NOTIFY_BAD on error.
478 */
479static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
480 unsigned long event, void *data)
481{
482 u32 ctrl_reg;
483 struct uart_port *port;
484 int locked = 0;
485 struct clk_notifier_data *ndata = data;
486 struct cdns_uart *cdns_uart = to_cdns_uart(nb);
487 unsigned long flags;
488
489 port = cdns_uart->port;
490 if (port->suspended)
491 return NOTIFY_OK;
492
493 switch (event) {
494 case PRE_RATE_CHANGE:
495 {
496 u32 bdiv, cd;
497 int div8;
498
499 /*
500 * Find out if current baud-rate can be achieved with new clock
501 * frequency.
502 */
503 if (!cdns_uart_calc_baud_divs(ndata->new_rate, cdns_uart->baud,
504 &bdiv, &cd, &div8)) {
505 dev_warn(port->dev, "clock rate change rejected\n");
506 return NOTIFY_BAD;
507 }
508
509 uart_port_lock_irqsave(cdns_uart->port, &flags);
510
511 /* Disable the TX and RX to set baud rate */
512 ctrl_reg = readl(port->membase + CDNS_UART_CR);
513 ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
514 writel(ctrl_reg, port->membase + CDNS_UART_CR);
515
516 uart_port_unlock_irqrestore(cdns_uart->port, flags);
517
518 return NOTIFY_OK;
519 }
520 case POST_RATE_CHANGE:
521 /*
522 * Set clk dividers to generate correct baud with new clock
523 * frequency.
524 */
525
526 uart_port_lock_irqsave(cdns_uart->port, &flags);
527
528 locked = 1;
529 port->uartclk = ndata->new_rate;
530
531 cdns_uart->baud = cdns_uart_set_baud_rate(cdns_uart->port,
532 cdns_uart->baud);
533 fallthrough;
534 case ABORT_RATE_CHANGE:
535 if (!locked)
536 uart_port_lock_irqsave(cdns_uart->port, &flags);
537
538 /* Set TX/RX Reset */
539 ctrl_reg = readl(port->membase + CDNS_UART_CR);
540 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
541 writel(ctrl_reg, port->membase + CDNS_UART_CR);
542
543 while (readl(port->membase + CDNS_UART_CR) &
544 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
545 cpu_relax();
546
547 /*
548 * Clear the RX disable and TX disable bits and then set the TX
549 * enable bit and RX enable bit to enable the transmitter and
550 * receiver.
551 */
552 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
553 ctrl_reg = readl(port->membase + CDNS_UART_CR);
554 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
555 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
556 writel(ctrl_reg, port->membase + CDNS_UART_CR);
557
558 uart_port_unlock_irqrestore(cdns_uart->port, flags);
559
560 return NOTIFY_OK;
561 default:
562 return NOTIFY_DONE;
563 }
564}
565#endif
566
567/**
568 * cdns_uart_start_tx - Start transmitting bytes
569 * @port: Handle to the uart port structure
570 */
571static void cdns_uart_start_tx(struct uart_port *port)
572{
573 unsigned int status;
574
575 if (uart_tx_stopped(port))
576 return;
577
578 /*
579 * Set the TX enable bit and clear the TX disable bit to enable the
580 * transmitter.
581 */
582 status = readl(port->membase + CDNS_UART_CR);
583 status &= ~CDNS_UART_CR_TX_DIS;
584 status |= CDNS_UART_CR_TX_EN;
585 writel(status, port->membase + CDNS_UART_CR);
586
587 if (uart_circ_empty(&port->state->xmit))
588 return;
589
590 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR);
591
592 cdns_uart_handle_tx(port);
593
594 /* Enable the TX Empty interrupt */
595 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER);
596}
597
598/**
599 * cdns_uart_stop_tx - Stop TX
600 * @port: Handle to the uart port structure
601 */
602static void cdns_uart_stop_tx(struct uart_port *port)
603{
604 unsigned int regval;
605
606 regval = readl(port->membase + CDNS_UART_CR);
607 regval |= CDNS_UART_CR_TX_DIS;
608 /* Disable the transmitter */
609 writel(regval, port->membase + CDNS_UART_CR);
610}
611
612/**
613 * cdns_uart_stop_rx - Stop RX
614 * @port: Handle to the uart port structure
615 */
616static void cdns_uart_stop_rx(struct uart_port *port)
617{
618 unsigned int regval;
619
620 /* Disable RX IRQs */
621 writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IDR);
622
623 /* Disable the receiver */
624 regval = readl(port->membase + CDNS_UART_CR);
625 regval |= CDNS_UART_CR_RX_DIS;
626 writel(regval, port->membase + CDNS_UART_CR);
627}
628
629/**
630 * cdns_uart_tx_empty - Check whether TX is empty
631 * @port: Handle to the uart port structure
632 *
633 * Return: TIOCSER_TEMT on success, 0 otherwise
634 */
635static unsigned int cdns_uart_tx_empty(struct uart_port *port)
636{
637 unsigned int status;
638
639 status = readl(port->membase + CDNS_UART_SR) &
640 (CDNS_UART_SR_TXEMPTY | CDNS_UART_SR_TACTIVE);
641 return (status == CDNS_UART_SR_TXEMPTY) ? TIOCSER_TEMT : 0;
642}
643
644/**
645 * cdns_uart_break_ctl - Based on the input ctl we have to start or stop
646 * transmitting char breaks
647 * @port: Handle to the uart port structure
648 * @ctl: Value based on which start or stop decision is taken
649 */
650static void cdns_uart_break_ctl(struct uart_port *port, int ctl)
651{
652 unsigned int status;
653 unsigned long flags;
654
655 uart_port_lock_irqsave(port, &flags);
656
657 status = readl(port->membase + CDNS_UART_CR);
658
659 if (ctl == -1)
660 writel(CDNS_UART_CR_STARTBRK | (~CDNS_UART_CR_STOPBRK & status),
661 port->membase + CDNS_UART_CR);
662 else {
663 if ((status & CDNS_UART_CR_STOPBRK) == 0)
664 writel(CDNS_UART_CR_STOPBRK | status,
665 port->membase + CDNS_UART_CR);
666 }
667 uart_port_unlock_irqrestore(port, flags);
668}
669
670/**
671 * cdns_uart_set_termios - termios operations, handling data length, parity,
672 * stop bits, flow control, baud rate
673 * @port: Handle to the uart port structure
674 * @termios: Handle to the input termios structure
675 * @old: Values of the previously saved termios structure
676 */
677static void cdns_uart_set_termios(struct uart_port *port,
678 struct ktermios *termios,
679 const struct ktermios *old)
680{
681 u32 cval = 0;
682 unsigned int baud, minbaud, maxbaud;
683 unsigned long flags;
684 unsigned int ctrl_reg, mode_reg;
685
686 uart_port_lock_irqsave(port, &flags);
687
688 /* Disable the TX and RX to set baud rate */
689 ctrl_reg = readl(port->membase + CDNS_UART_CR);
690 ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
691 writel(ctrl_reg, port->membase + CDNS_UART_CR);
692
693 /*
694 * Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
695 * min and max baud should be calculated here based on port->uartclk.
696 * this way we get a valid baud and can safely call set_baud()
697 */
698 minbaud = port->uartclk /
699 ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX * 8);
700 maxbaud = port->uartclk / (CDNS_UART_BDIV_MIN + 1);
701 baud = uart_get_baud_rate(port, termios, old, minbaud, maxbaud);
702 baud = cdns_uart_set_baud_rate(port, baud);
703 if (tty_termios_baud_rate(termios))
704 tty_termios_encode_baud_rate(termios, baud, baud);
705
706 /* Update the per-port timeout. */
707 uart_update_timeout(port, termios->c_cflag, baud);
708
709 /* Set TX/RX Reset */
710 ctrl_reg = readl(port->membase + CDNS_UART_CR);
711 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
712 writel(ctrl_reg, port->membase + CDNS_UART_CR);
713
714 while (readl(port->membase + CDNS_UART_CR) &
715 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
716 cpu_relax();
717
718 /*
719 * Clear the RX disable and TX disable bits and then set the TX enable
720 * bit and RX enable bit to enable the transmitter and receiver.
721 */
722 ctrl_reg = readl(port->membase + CDNS_UART_CR);
723 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
724 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
725 writel(ctrl_reg, port->membase + CDNS_UART_CR);
726
727 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
728
729 port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
730 CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
731 port->ignore_status_mask = 0;
732
733 if (termios->c_iflag & INPCK)
734 port->read_status_mask |= CDNS_UART_IXR_PARITY |
735 CDNS_UART_IXR_FRAMING;
736
737 if (termios->c_iflag & IGNPAR)
738 port->ignore_status_mask |= CDNS_UART_IXR_PARITY |
739 CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
740
741 /* ignore all characters if CREAD is not set */
742 if ((termios->c_cflag & CREAD) == 0)
743 port->ignore_status_mask |= CDNS_UART_IXR_RXTRIG |
744 CDNS_UART_IXR_TOUT | CDNS_UART_IXR_PARITY |
745 CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
746
747 mode_reg = readl(port->membase + CDNS_UART_MR);
748
749 /* Handling Data Size */
750 switch (termios->c_cflag & CSIZE) {
751 case CS6:
752 cval |= CDNS_UART_MR_CHARLEN_6_BIT;
753 break;
754 case CS7:
755 cval |= CDNS_UART_MR_CHARLEN_7_BIT;
756 break;
757 default:
758 case CS8:
759 cval |= CDNS_UART_MR_CHARLEN_8_BIT;
760 termios->c_cflag &= ~CSIZE;
761 termios->c_cflag |= CS8;
762 break;
763 }
764
765 /* Handling Parity and Stop Bits length */
766 if (termios->c_cflag & CSTOPB)
767 cval |= CDNS_UART_MR_STOPMODE_2_BIT; /* 2 STOP bits */
768 else
769 cval |= CDNS_UART_MR_STOPMODE_1_BIT; /* 1 STOP bit */
770
771 if (termios->c_cflag & PARENB) {
772 /* Mark or Space parity */
773 if (termios->c_cflag & CMSPAR) {
774 if (termios->c_cflag & PARODD)
775 cval |= CDNS_UART_MR_PARITY_MARK;
776 else
777 cval |= CDNS_UART_MR_PARITY_SPACE;
778 } else {
779 if (termios->c_cflag & PARODD)
780 cval |= CDNS_UART_MR_PARITY_ODD;
781 else
782 cval |= CDNS_UART_MR_PARITY_EVEN;
783 }
784 } else {
785 cval |= CDNS_UART_MR_PARITY_NONE;
786 }
787 cval |= mode_reg & 1;
788 writel(cval, port->membase + CDNS_UART_MR);
789
790 cval = readl(port->membase + CDNS_UART_MODEMCR);
791 if (termios->c_cflag & CRTSCTS)
792 cval |= CDNS_UART_MODEMCR_FCM;
793 else
794 cval &= ~CDNS_UART_MODEMCR_FCM;
795 writel(cval, port->membase + CDNS_UART_MODEMCR);
796
797 uart_port_unlock_irqrestore(port, flags);
798}
799
800/**
801 * cdns_uart_startup - Called when an application opens a cdns_uart port
802 * @port: Handle to the uart port structure
803 *
804 * Return: 0 on success, negative errno otherwise
805 */
806static int cdns_uart_startup(struct uart_port *port)
807{
808 struct cdns_uart *cdns_uart = port->private_data;
809 bool is_brk_support;
810 int ret;
811 unsigned long flags;
812 unsigned int status = 0;
813
814 is_brk_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
815
816 uart_port_lock_irqsave(port, &flags);
817
818 /* Disable the TX and RX */
819 writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
820 port->membase + CDNS_UART_CR);
821
822 /* Set the Control Register with TX/RX Enable, TX/RX Reset,
823 * no break chars.
824 */
825 writel(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST,
826 port->membase + CDNS_UART_CR);
827
828 while (readl(port->membase + CDNS_UART_CR) &
829 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
830 cpu_relax();
831
832 /*
833 * Clear the RX disable bit and then set the RX enable bit to enable
834 * the receiver.
835 */
836 status = readl(port->membase + CDNS_UART_CR);
837 status &= ~CDNS_UART_CR_RX_DIS;
838 status |= CDNS_UART_CR_RX_EN;
839 writel(status, port->membase + CDNS_UART_CR);
840
841 /* Set the Mode Register with normal mode,8 data bits,1 stop bit,
842 * no parity.
843 */
844 writel(CDNS_UART_MR_CHMODE_NORM | CDNS_UART_MR_STOPMODE_1_BIT
845 | CDNS_UART_MR_PARITY_NONE | CDNS_UART_MR_CHARLEN_8_BIT,
846 port->membase + CDNS_UART_MR);
847
848 /*
849 * Set the RX FIFO Trigger level to use most of the FIFO, but it
850 * can be tuned with a module parameter
851 */
852 writel(rx_trigger_level, port->membase + CDNS_UART_RXWM);
853
854 /*
855 * Receive Timeout register is enabled but it
856 * can be tuned with a module parameter
857 */
858 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
859
860 /* Clear out any pending interrupts before enabling them */
861 writel(readl(port->membase + CDNS_UART_ISR),
862 port->membase + CDNS_UART_ISR);
863
864 uart_port_unlock_irqrestore(port, flags);
865
866 ret = request_irq(port->irq, cdns_uart_isr, 0, CDNS_UART_NAME, port);
867 if (ret) {
868 dev_err(port->dev, "request_irq '%d' failed with %d\n",
869 port->irq, ret);
870 return ret;
871 }
872
873 /* Set the Interrupt Registers with desired interrupts */
874 if (is_brk_support)
875 writel(CDNS_UART_RX_IRQS | CDNS_UART_IXR_BRK,
876 port->membase + CDNS_UART_IER);
877 else
878 writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IER);
879
880 return 0;
881}
882
883/**
884 * cdns_uart_shutdown - Called when an application closes a cdns_uart port
885 * @port: Handle to the uart port structure
886 */
887static void cdns_uart_shutdown(struct uart_port *port)
888{
889 int status;
890 unsigned long flags;
891
892 uart_port_lock_irqsave(port, &flags);
893
894 /* Disable interrupts */
895 status = readl(port->membase + CDNS_UART_IMR);
896 writel(status, port->membase + CDNS_UART_IDR);
897 writel(0xffffffff, port->membase + CDNS_UART_ISR);
898
899 /* Disable the TX and RX */
900 writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
901 port->membase + CDNS_UART_CR);
902
903 uart_port_unlock_irqrestore(port, flags);
904
905 free_irq(port->irq, port);
906}
907
908/**
909 * cdns_uart_type - Set UART type to cdns_uart port
910 * @port: Handle to the uart port structure
911 *
912 * Return: string on success, NULL otherwise
913 */
914static const char *cdns_uart_type(struct uart_port *port)
915{
916 return port->type == PORT_XUARTPS ? CDNS_UART_NAME : NULL;
917}
918
919/**
920 * cdns_uart_verify_port - Verify the port params
921 * @port: Handle to the uart port structure
922 * @ser: Handle to the structure whose members are compared
923 *
924 * Return: 0 on success, negative errno otherwise.
925 */
926static int cdns_uart_verify_port(struct uart_port *port,
927 struct serial_struct *ser)
928{
929 if (ser->type != PORT_UNKNOWN && ser->type != PORT_XUARTPS)
930 return -EINVAL;
931 if (port->irq != ser->irq)
932 return -EINVAL;
933 if (ser->io_type != UPIO_MEM)
934 return -EINVAL;
935 if (port->iobase != ser->port)
936 return -EINVAL;
937 if (ser->hub6 != 0)
938 return -EINVAL;
939 return 0;
940}
941
942/**
943 * cdns_uart_request_port - Claim the memory region attached to cdns_uart port,
944 * called when the driver adds a cdns_uart port via
945 * uart_add_one_port()
946 * @port: Handle to the uart port structure
947 *
948 * Return: 0 on success, negative errno otherwise.
949 */
950static int cdns_uart_request_port(struct uart_port *port)
951{
952 if (!request_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE,
953 CDNS_UART_NAME)) {
954 return -ENOMEM;
955 }
956
957 port->membase = ioremap(port->mapbase, CDNS_UART_REGISTER_SPACE);
958 if (!port->membase) {
959 dev_err(port->dev, "Unable to map registers\n");
960 release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
961 return -ENOMEM;
962 }
963 return 0;
964}
965
966/**
967 * cdns_uart_release_port - Release UART port
968 * @port: Handle to the uart port structure
969 *
970 * Release the memory region attached to a cdns_uart port. Called when the
971 * driver removes a cdns_uart port via uart_remove_one_port().
972 */
973static void cdns_uart_release_port(struct uart_port *port)
974{
975 release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
976 iounmap(port->membase);
977 port->membase = NULL;
978}
979
980/**
981 * cdns_uart_config_port - Configure UART port
982 * @port: Handle to the uart port structure
983 * @flags: If any
984 */
985static void cdns_uart_config_port(struct uart_port *port, int flags)
986{
987 if (flags & UART_CONFIG_TYPE && cdns_uart_request_port(port) == 0)
988 port->type = PORT_XUARTPS;
989}
990
991/**
992 * cdns_uart_get_mctrl - Get the modem control state
993 * @port: Handle to the uart port structure
994 *
995 * Return: the modem control state
996 */
997static unsigned int cdns_uart_get_mctrl(struct uart_port *port)
998{
999 u32 val;
1000 unsigned int mctrl = 0;
1001 struct cdns_uart *cdns_uart_data = port->private_data;
1002
1003 if (cdns_uart_data->cts_override)
1004 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
1005
1006 val = readl(port->membase + CDNS_UART_MODEMSR);
1007 if (val & CDNS_UART_MODEMSR_CTS)
1008 mctrl |= TIOCM_CTS;
1009 if (val & CDNS_UART_MODEMSR_DSR)
1010 mctrl |= TIOCM_DSR;
1011 if (val & CDNS_UART_MODEMSR_RI)
1012 mctrl |= TIOCM_RNG;
1013 if (val & CDNS_UART_MODEMSR_DCD)
1014 mctrl |= TIOCM_CAR;
1015
1016 return mctrl;
1017}
1018
1019static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1020{
1021 u32 val;
1022 u32 mode_reg;
1023 struct cdns_uart *cdns_uart_data = port->private_data;
1024
1025 if (cdns_uart_data->cts_override)
1026 return;
1027
1028 val = readl(port->membase + CDNS_UART_MODEMCR);
1029 mode_reg = readl(port->membase + CDNS_UART_MR);
1030
1031 val &= ~(CDNS_UART_MODEMCR_RTS | CDNS_UART_MODEMCR_DTR);
1032 mode_reg &= ~CDNS_UART_MR_CHMODE_MASK;
1033
1034 if (mctrl & TIOCM_RTS)
1035 val |= CDNS_UART_MODEMCR_RTS;
1036 if (mctrl & TIOCM_DTR)
1037 val |= CDNS_UART_MODEMCR_DTR;
1038 if (mctrl & TIOCM_LOOP)
1039 mode_reg |= CDNS_UART_MR_CHMODE_L_LOOP;
1040 else
1041 mode_reg |= CDNS_UART_MR_CHMODE_NORM;
1042
1043 writel(val, port->membase + CDNS_UART_MODEMCR);
1044 writel(mode_reg, port->membase + CDNS_UART_MR);
1045}
1046
1047#ifdef CONFIG_CONSOLE_POLL
1048static int cdns_uart_poll_get_char(struct uart_port *port)
1049{
1050 int c;
1051 unsigned long flags;
1052
1053 uart_port_lock_irqsave(port, &flags);
1054
1055 /* Check if FIFO is empty */
1056 if (readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY)
1057 c = NO_POLL_CHAR;
1058 else /* Read a character */
1059 c = (unsigned char) readl(port->membase + CDNS_UART_FIFO);
1060
1061 uart_port_unlock_irqrestore(port, flags);
1062
1063 return c;
1064}
1065
1066static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c)
1067{
1068 unsigned long flags;
1069
1070 uart_port_lock_irqsave(port, &flags);
1071
1072 /* Wait until FIFO is empty */
1073 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1074 cpu_relax();
1075
1076 /* Write a character */
1077 writel(c, port->membase + CDNS_UART_FIFO);
1078
1079 /* Wait until FIFO is empty */
1080 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1081 cpu_relax();
1082
1083 uart_port_unlock_irqrestore(port, flags);
1084}
1085#endif
1086
1087static void cdns_uart_pm(struct uart_port *port, unsigned int state,
1088 unsigned int oldstate)
1089{
1090 switch (state) {
1091 case UART_PM_STATE_OFF:
1092 pm_runtime_mark_last_busy(port->dev);
1093 pm_runtime_put_autosuspend(port->dev);
1094 break;
1095 default:
1096 pm_runtime_get_sync(port->dev);
1097 break;
1098 }
1099}
1100
1101static const struct uart_ops cdns_uart_ops = {
1102 .set_mctrl = cdns_uart_set_mctrl,
1103 .get_mctrl = cdns_uart_get_mctrl,
1104 .start_tx = cdns_uart_start_tx,
1105 .stop_tx = cdns_uart_stop_tx,
1106 .stop_rx = cdns_uart_stop_rx,
1107 .tx_empty = cdns_uart_tx_empty,
1108 .break_ctl = cdns_uart_break_ctl,
1109 .set_termios = cdns_uart_set_termios,
1110 .startup = cdns_uart_startup,
1111 .shutdown = cdns_uart_shutdown,
1112 .pm = cdns_uart_pm,
1113 .type = cdns_uart_type,
1114 .verify_port = cdns_uart_verify_port,
1115 .request_port = cdns_uart_request_port,
1116 .release_port = cdns_uart_release_port,
1117 .config_port = cdns_uart_config_port,
1118#ifdef CONFIG_CONSOLE_POLL
1119 .poll_get_char = cdns_uart_poll_get_char,
1120 .poll_put_char = cdns_uart_poll_put_char,
1121#endif
1122};
1123
1124static struct uart_driver cdns_uart_uart_driver;
1125
1126#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1127/**
1128 * cdns_uart_console_putchar - write the character to the FIFO buffer
1129 * @port: Handle to the uart port structure
1130 * @ch: Character to be written
1131 */
1132static void cdns_uart_console_putchar(struct uart_port *port, unsigned char ch)
1133{
1134 unsigned int ctrl_reg;
1135 unsigned long timeout;
1136
1137 timeout = jiffies + msecs_to_jiffies(1000);
1138 while (1) {
1139 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1140 if (!(ctrl_reg & CDNS_UART_CR_TX_DIS))
1141 break;
1142 if (time_after(jiffies, timeout)) {
1143 dev_warn(port->dev,
1144 "timeout waiting for Enable\n");
1145 return;
1146 }
1147 cpu_relax();
1148 }
1149
1150 timeout = jiffies + msecs_to_jiffies(1000);
1151 while (1) {
1152 ctrl_reg = readl(port->membase + CDNS_UART_SR);
1153
1154 if (!(ctrl_reg & CDNS_UART_SR_TXFULL))
1155 break;
1156 if (time_after(jiffies, timeout)) {
1157 dev_warn(port->dev,
1158 "timeout waiting for TX fifo\n");
1159 return;
1160 }
1161 cpu_relax();
1162 }
1163 writel(ch, port->membase + CDNS_UART_FIFO);
1164}
1165
1166static void cdns_early_write(struct console *con, const char *s,
1167 unsigned int n)
1168{
1169 struct earlycon_device *dev = con->data;
1170
1171 uart_console_write(&dev->port, s, n, cdns_uart_console_putchar);
1172}
1173
1174static int __init cdns_early_console_setup(struct earlycon_device *device,
1175 const char *opt)
1176{
1177 struct uart_port *port = &device->port;
1178
1179 if (!port->membase)
1180 return -ENODEV;
1181
1182 /* initialise control register */
1183 writel(CDNS_UART_CR_TX_EN|CDNS_UART_CR_TXRST|CDNS_UART_CR_RXRST,
1184 port->membase + CDNS_UART_CR);
1185
1186 /* only set baud if specified on command line - otherwise
1187 * assume it has been initialized by a boot loader.
1188 */
1189 if (port->uartclk && device->baud) {
1190 u32 cd = 0, bdiv = 0;
1191 u32 mr;
1192 int div8;
1193
1194 cdns_uart_calc_baud_divs(port->uartclk, device->baud,
1195 &bdiv, &cd, &div8);
1196 mr = CDNS_UART_MR_PARITY_NONE;
1197 if (div8)
1198 mr |= CDNS_UART_MR_CLKSEL;
1199
1200 writel(mr, port->membase + CDNS_UART_MR);
1201 writel(cd, port->membase + CDNS_UART_BAUDGEN);
1202 writel(bdiv, port->membase + CDNS_UART_BAUDDIV);
1203 }
1204
1205 device->con->write = cdns_early_write;
1206
1207 return 0;
1208}
1209OF_EARLYCON_DECLARE(cdns, "xlnx,xuartps", cdns_early_console_setup);
1210OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup);
1211OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup);
1212OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
1213
1214
1215/* Static pointer to console port */
1216static struct uart_port *console_port;
1217
1218/**
1219 * cdns_uart_console_write - perform write operation
1220 * @co: Console handle
1221 * @s: Pointer to character array
1222 * @count: No of characters
1223 */
1224static void cdns_uart_console_write(struct console *co, const char *s,
1225 unsigned int count)
1226{
1227 struct uart_port *port = console_port;
1228 unsigned long flags;
1229 unsigned int imr, ctrl;
1230 int locked = 1;
1231
1232 if (port->sysrq)
1233 locked = 0;
1234 else if (oops_in_progress)
1235 locked = uart_port_trylock_irqsave(port, &flags);
1236 else
1237 uart_port_lock_irqsave(port, &flags);
1238
1239 /* save and disable interrupt */
1240 imr = readl(port->membase + CDNS_UART_IMR);
1241 writel(imr, port->membase + CDNS_UART_IDR);
1242
1243 /*
1244 * Make sure that the tx part is enabled. Set the TX enable bit and
1245 * clear the TX disable bit to enable the transmitter.
1246 */
1247 ctrl = readl(port->membase + CDNS_UART_CR);
1248 ctrl &= ~CDNS_UART_CR_TX_DIS;
1249 ctrl |= CDNS_UART_CR_TX_EN;
1250 writel(ctrl, port->membase + CDNS_UART_CR);
1251
1252 uart_console_write(port, s, count, cdns_uart_console_putchar);
1253 while (cdns_uart_tx_empty(port) != TIOCSER_TEMT)
1254 cpu_relax();
1255
1256 /* restore interrupt state */
1257 writel(imr, port->membase + CDNS_UART_IER);
1258
1259 if (locked)
1260 uart_port_unlock_irqrestore(port, flags);
1261}
1262
1263/**
1264 * cdns_uart_console_setup - Initialize the uart to default config
1265 * @co: Console handle
1266 * @options: Initial settings of uart
1267 *
1268 * Return: 0 on success, negative errno otherwise.
1269 */
1270static int cdns_uart_console_setup(struct console *co, char *options)
1271{
1272 struct uart_port *port = console_port;
1273
1274 int baud = 9600;
1275 int bits = 8;
1276 int parity = 'n';
1277 int flow = 'n';
1278 unsigned long time_out;
1279
1280 if (!port->membase) {
1281 pr_debug("console on " CDNS_UART_TTY_NAME "%i not present\n",
1282 co->index);
1283 return -ENODEV;
1284 }
1285
1286 if (options)
1287 uart_parse_options(options, &baud, &parity, &bits, &flow);
1288
1289 /* Wait for tx_empty before setting up the console */
1290 time_out = jiffies + usecs_to_jiffies(TX_TIMEOUT);
1291
1292 while (time_before(jiffies, time_out) &&
1293 cdns_uart_tx_empty(port) != TIOCSER_TEMT)
1294 cpu_relax();
1295
1296 return uart_set_options(port, co, baud, parity, bits, flow);
1297}
1298
1299static struct console cdns_uart_console = {
1300 .name = CDNS_UART_TTY_NAME,
1301 .write = cdns_uart_console_write,
1302 .device = uart_console_device,
1303 .setup = cdns_uart_console_setup,
1304 .flags = CON_PRINTBUFFER,
1305 .index = -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
1306 .data = &cdns_uart_uart_driver,
1307};
1308#endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
1309
1310#ifdef CONFIG_PM_SLEEP
1311/**
1312 * cdns_uart_suspend - suspend event
1313 * @device: Pointer to the device structure
1314 *
1315 * Return: 0
1316 */
1317static int cdns_uart_suspend(struct device *device)
1318{
1319 struct uart_port *port = dev_get_drvdata(device);
1320 struct cdns_uart *cdns_uart = port->private_data;
1321 int may_wake;
1322
1323 may_wake = device_may_wakeup(device);
1324
1325 if (console_suspend_enabled && uart_console(port) && may_wake) {
1326 unsigned long flags;
1327
1328 uart_port_lock_irqsave(port, &flags);
1329 /* Empty the receive FIFO 1st before making changes */
1330 while (!(readl(port->membase + CDNS_UART_SR) &
1331 CDNS_UART_SR_RXEMPTY))
1332 readl(port->membase + CDNS_UART_FIFO);
1333 /* set RX trigger level to 1 */
1334 writel(1, port->membase + CDNS_UART_RXWM);
1335 /* disable RX timeout interrups */
1336 writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IDR);
1337 uart_port_unlock_irqrestore(port, flags);
1338 }
1339
1340 /*
1341 * Call the API provided in serial_core.c file which handles
1342 * the suspend.
1343 */
1344 return uart_suspend_port(cdns_uart->cdns_uart_driver, port);
1345}
1346
1347/**
1348 * cdns_uart_resume - Resume after a previous suspend
1349 * @device: Pointer to the device structure
1350 *
1351 * Return: 0
1352 */
1353static int cdns_uart_resume(struct device *device)
1354{
1355 struct uart_port *port = dev_get_drvdata(device);
1356 struct cdns_uart *cdns_uart = port->private_data;
1357 unsigned long flags;
1358 u32 ctrl_reg;
1359 int may_wake;
1360 int ret;
1361
1362 may_wake = device_may_wakeup(device);
1363
1364 if (console_suspend_enabled && uart_console(port) && !may_wake) {
1365 ret = clk_enable(cdns_uart->pclk);
1366 if (ret)
1367 return ret;
1368
1369 ret = clk_enable(cdns_uart->uartclk);
1370 if (ret) {
1371 clk_disable(cdns_uart->pclk);
1372 return ret;
1373 }
1374
1375 uart_port_lock_irqsave(port, &flags);
1376
1377 /* Set TX/RX Reset */
1378 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1379 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
1380 writel(ctrl_reg, port->membase + CDNS_UART_CR);
1381 while (readl(port->membase + CDNS_UART_CR) &
1382 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
1383 cpu_relax();
1384
1385 /* restore rx timeout value */
1386 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
1387 /* Enable Tx/Rx */
1388 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1389 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
1390 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
1391 writel(ctrl_reg, port->membase + CDNS_UART_CR);
1392
1393 clk_disable(cdns_uart->uartclk);
1394 clk_disable(cdns_uart->pclk);
1395 uart_port_unlock_irqrestore(port, flags);
1396 } else {
1397 uart_port_lock_irqsave(port, &flags);
1398 /* restore original rx trigger level */
1399 writel(rx_trigger_level, port->membase + CDNS_UART_RXWM);
1400 /* enable RX timeout interrupt */
1401 writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IER);
1402 uart_port_unlock_irqrestore(port, flags);
1403 }
1404
1405 return uart_resume_port(cdns_uart->cdns_uart_driver, port);
1406}
1407#endif /* ! CONFIG_PM_SLEEP */
1408static int __maybe_unused cdns_runtime_suspend(struct device *dev)
1409{
1410 struct uart_port *port = dev_get_drvdata(dev);
1411 struct cdns_uart *cdns_uart = port->private_data;
1412
1413 clk_disable(cdns_uart->uartclk);
1414 clk_disable(cdns_uart->pclk);
1415 return 0;
1416};
1417
1418static int __maybe_unused cdns_runtime_resume(struct device *dev)
1419{
1420 struct uart_port *port = dev_get_drvdata(dev);
1421 struct cdns_uart *cdns_uart = port->private_data;
1422 int ret;
1423
1424 ret = clk_enable(cdns_uart->pclk);
1425 if (ret)
1426 return ret;
1427
1428 ret = clk_enable(cdns_uart->uartclk);
1429 if (ret) {
1430 clk_disable(cdns_uart->pclk);
1431 return ret;
1432 }
1433 return 0;
1434};
1435
1436static const struct dev_pm_ops cdns_uart_dev_pm_ops = {
1437 SET_SYSTEM_SLEEP_PM_OPS(cdns_uart_suspend, cdns_uart_resume)
1438 SET_RUNTIME_PM_OPS(cdns_runtime_suspend,
1439 cdns_runtime_resume, NULL)
1440};
1441
1442static const struct cdns_platform_data zynqmp_uart_def = {
1443 .quirks = CDNS_UART_RXBS_SUPPORT, };
1444
1445/* Match table for of_platform binding */
1446static const struct of_device_id cdns_uart_of_match[] = {
1447 { .compatible = "xlnx,xuartps", },
1448 { .compatible = "cdns,uart-r1p8", },
1449 { .compatible = "cdns,uart-r1p12", .data = &zynqmp_uart_def },
1450 { .compatible = "xlnx,zynqmp-uart", .data = &zynqmp_uart_def },
1451 {}
1452};
1453MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
1454
1455/* Temporary variable for storing number of instances */
1456static int instances;
1457
1458/**
1459 * cdns_uart_probe - Platform driver probe
1460 * @pdev: Pointer to the platform device structure
1461 *
1462 * Return: 0 on success, negative errno otherwise
1463 */
1464static int cdns_uart_probe(struct platform_device *pdev)
1465{
1466 int rc, id, irq;
1467 struct uart_port *port;
1468 struct resource *res;
1469 struct cdns_uart *cdns_uart_data;
1470 const struct of_device_id *match;
1471
1472 cdns_uart_data = devm_kzalloc(&pdev->dev, sizeof(*cdns_uart_data),
1473 GFP_KERNEL);
1474 if (!cdns_uart_data)
1475 return -ENOMEM;
1476 port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
1477 if (!port)
1478 return -ENOMEM;
1479
1480 /* Look for a serialN alias */
1481 id = of_alias_get_id(pdev->dev.of_node, "serial");
1482 if (id < 0)
1483 id = 0;
1484
1485 if (id >= CDNS_UART_NR_PORTS) {
1486 dev_err(&pdev->dev, "Cannot get uart_port structure\n");
1487 return -ENODEV;
1488 }
1489
1490 if (!cdns_uart_uart_driver.state) {
1491 cdns_uart_uart_driver.owner = THIS_MODULE;
1492 cdns_uart_uart_driver.driver_name = CDNS_UART_NAME;
1493 cdns_uart_uart_driver.dev_name = CDNS_UART_TTY_NAME;
1494 cdns_uart_uart_driver.major = CDNS_UART_MAJOR;
1495 cdns_uart_uart_driver.minor = CDNS_UART_MINOR;
1496 cdns_uart_uart_driver.nr = CDNS_UART_NR_PORTS;
1497#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1498 cdns_uart_uart_driver.cons = &cdns_uart_console;
1499#endif
1500
1501 rc = uart_register_driver(&cdns_uart_uart_driver);
1502 if (rc < 0) {
1503 dev_err(&pdev->dev, "Failed to register driver\n");
1504 return rc;
1505 }
1506 }
1507
1508 cdns_uart_data->cdns_uart_driver = &cdns_uart_uart_driver;
1509
1510 match = of_match_node(cdns_uart_of_match, pdev->dev.of_node);
1511 if (match && match->data) {
1512 const struct cdns_platform_data *data = match->data;
1513
1514 cdns_uart_data->quirks = data->quirks;
1515 }
1516
1517 cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "pclk");
1518 if (PTR_ERR(cdns_uart_data->pclk) == -EPROBE_DEFER) {
1519 rc = PTR_ERR(cdns_uart_data->pclk);
1520 goto err_out_unregister_driver;
1521 }
1522
1523 if (IS_ERR(cdns_uart_data->pclk)) {
1524 cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk");
1525 if (IS_ERR(cdns_uart_data->pclk)) {
1526 rc = PTR_ERR(cdns_uart_data->pclk);
1527 goto err_out_unregister_driver;
1528 }
1529 dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n");
1530 }
1531
1532 cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk");
1533 if (PTR_ERR(cdns_uart_data->uartclk) == -EPROBE_DEFER) {
1534 rc = PTR_ERR(cdns_uart_data->uartclk);
1535 goto err_out_unregister_driver;
1536 }
1537
1538 if (IS_ERR(cdns_uart_data->uartclk)) {
1539 cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk");
1540 if (IS_ERR(cdns_uart_data->uartclk)) {
1541 rc = PTR_ERR(cdns_uart_data->uartclk);
1542 goto err_out_unregister_driver;
1543 }
1544 dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
1545 }
1546
1547 rc = clk_prepare_enable(cdns_uart_data->pclk);
1548 if (rc) {
1549 dev_err(&pdev->dev, "Unable to enable pclk clock.\n");
1550 goto err_out_unregister_driver;
1551 }
1552 rc = clk_prepare_enable(cdns_uart_data->uartclk);
1553 if (rc) {
1554 dev_err(&pdev->dev, "Unable to enable device clock.\n");
1555 goto err_out_clk_dis_pclk;
1556 }
1557
1558 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1559 if (!res) {
1560 rc = -ENODEV;
1561 goto err_out_clk_disable;
1562 }
1563
1564 irq = platform_get_irq(pdev, 0);
1565 if (irq < 0) {
1566 rc = irq;
1567 goto err_out_clk_disable;
1568 }
1569
1570#ifdef CONFIG_COMMON_CLK
1571 cdns_uart_data->clk_rate_change_nb.notifier_call =
1572 cdns_uart_clk_notifier_cb;
1573 if (clk_notifier_register(cdns_uart_data->uartclk,
1574 &cdns_uart_data->clk_rate_change_nb))
1575 dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
1576#endif
1577
1578 /* At this point, we've got an empty uart_port struct, initialize it */
1579 spin_lock_init(&port->lock);
1580 port->type = PORT_UNKNOWN;
1581 port->iotype = UPIO_MEM32;
1582 port->flags = UPF_BOOT_AUTOCONF;
1583 port->ops = &cdns_uart_ops;
1584 port->fifosize = CDNS_UART_FIFO_SIZE;
1585 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE);
1586 port->line = id;
1587
1588 /*
1589 * Register the port.
1590 * This function also registers this device with the tty layer
1591 * and triggers invocation of the config_port() entry point.
1592 */
1593 port->mapbase = res->start;
1594 port->irq = irq;
1595 port->dev = &pdev->dev;
1596 port->uartclk = clk_get_rate(cdns_uart_data->uartclk);
1597 port->private_data = cdns_uart_data;
1598 port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
1599 CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
1600 cdns_uart_data->port = port;
1601 platform_set_drvdata(pdev, port);
1602
1603 pm_runtime_use_autosuspend(&pdev->dev);
1604 pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
1605 pm_runtime_set_active(&pdev->dev);
1606 pm_runtime_enable(&pdev->dev);
1607 device_init_wakeup(port->dev, true);
1608
1609#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1610 /*
1611 * If console hasn't been found yet try to assign this port
1612 * because it is required to be assigned for console setup function.
1613 * If register_console() don't assign value, then console_port pointer
1614 * is cleanup.
1615 */
1616 if (!console_port) {
1617 cdns_uart_console.index = id;
1618 console_port = port;
1619 }
1620#endif
1621
1622 rc = uart_add_one_port(&cdns_uart_uart_driver, port);
1623 if (rc) {
1624 dev_err(&pdev->dev,
1625 "uart_add_one_port() failed; err=%i\n", rc);
1626 goto err_out_pm_disable;
1627 }
1628
1629#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1630 /* This is not port which is used for console that's why clean it up */
1631 if (console_port == port &&
1632 !console_is_registered(cdns_uart_uart_driver.cons)) {
1633 console_port = NULL;
1634 cdns_uart_console.index = -1;
1635 }
1636#endif
1637
1638 cdns_uart_data->cts_override = of_property_read_bool(pdev->dev.of_node,
1639 "cts-override");
1640
1641 instances++;
1642
1643 return 0;
1644
1645err_out_pm_disable:
1646 pm_runtime_disable(&pdev->dev);
1647 pm_runtime_set_suspended(&pdev->dev);
1648 pm_runtime_dont_use_autosuspend(&pdev->dev);
1649#ifdef CONFIG_COMMON_CLK
1650 clk_notifier_unregister(cdns_uart_data->uartclk,
1651 &cdns_uart_data->clk_rate_change_nb);
1652#endif
1653err_out_clk_disable:
1654 clk_disable_unprepare(cdns_uart_data->uartclk);
1655err_out_clk_dis_pclk:
1656 clk_disable_unprepare(cdns_uart_data->pclk);
1657err_out_unregister_driver:
1658 if (!instances)
1659 uart_unregister_driver(cdns_uart_data->cdns_uart_driver);
1660 return rc;
1661}
1662
1663/**
1664 * cdns_uart_remove - called when the platform driver is unregistered
1665 * @pdev: Pointer to the platform device structure
1666 */
1667static void cdns_uart_remove(struct platform_device *pdev)
1668{
1669 struct uart_port *port = platform_get_drvdata(pdev);
1670 struct cdns_uart *cdns_uart_data = port->private_data;
1671
1672 /* Remove the cdns_uart port from the serial core */
1673#ifdef CONFIG_COMMON_CLK
1674 clk_notifier_unregister(cdns_uart_data->uartclk,
1675 &cdns_uart_data->clk_rate_change_nb);
1676#endif
1677 uart_remove_one_port(cdns_uart_data->cdns_uart_driver, port);
1678 port->mapbase = 0;
1679 clk_disable_unprepare(cdns_uart_data->uartclk);
1680 clk_disable_unprepare(cdns_uart_data->pclk);
1681 pm_runtime_disable(&pdev->dev);
1682 pm_runtime_set_suspended(&pdev->dev);
1683 pm_runtime_dont_use_autosuspend(&pdev->dev);
1684 device_init_wakeup(&pdev->dev, false);
1685
1686#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1687 if (console_port == port)
1688 console_port = NULL;
1689#endif
1690
1691 if (!--instances)
1692 uart_unregister_driver(cdns_uart_data->cdns_uart_driver);
1693}
1694
1695static struct platform_driver cdns_uart_platform_driver = {
1696 .probe = cdns_uart_probe,
1697 .remove_new = cdns_uart_remove,
1698 .driver = {
1699 .name = CDNS_UART_NAME,
1700 .of_match_table = cdns_uart_of_match,
1701 .pm = &cdns_uart_dev_pm_ops,
1702 .suppress_bind_attrs = IS_BUILTIN(CONFIG_SERIAL_XILINX_PS_UART),
1703 },
1704};
1705
1706static int __init cdns_uart_init(void)
1707{
1708 /* Register the platform driver */
1709 return platform_driver_register(&cdns_uart_platform_driver);
1710}
1711
1712static void __exit cdns_uart_exit(void)
1713{
1714 /* Unregister the platform driver */
1715 platform_driver_unregister(&cdns_uart_platform_driver);
1716}
1717
1718arch_initcall(cdns_uart_init);
1719module_exit(cdns_uart_exit);
1720
1721MODULE_DESCRIPTION("Driver for Cadence UART");
1722MODULE_AUTHOR("Xilinx Inc.");
1723MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Cadence UART driver (found in Xilinx Zynq)
4 *
5 * Copyright (c) 2011 - 2014 Xilinx, Inc.
6 *
7 * This driver has originally been pushed by Xilinx using a Zynq-branding. This
8 * still shows in the naming of this file, the kconfig symbols and some symbols
9 * in the code.
10 */
11
12#include <linux/platform_device.h>
13#include <linux/serial.h>
14#include <linux/console.h>
15#include <linux/serial_core.h>
16#include <linux/slab.h>
17#include <linux/tty.h>
18#include <linux/tty_flip.h>
19#include <linux/clk.h>
20#include <linux/irq.h>
21#include <linux/io.h>
22#include <linux/of.h>
23#include <linux/module.h>
24#include <linux/pm_runtime.h>
25#include <linux/gpio.h>
26#include <linux/gpio/consumer.h>
27#include <linux/delay.h>
28
29#define CDNS_UART_TTY_NAME "ttyPS"
30#define CDNS_UART_NAME "xuartps"
31#define CDNS_UART_MAJOR 0 /* use dynamic node allocation */
32#define CDNS_UART_MINOR 0 /* works best with devtmpfs */
33#define CDNS_UART_NR_PORTS 16
34#define CDNS_UART_FIFO_SIZE 64 /* FIFO size */
35#define CDNS_UART_REGISTER_SPACE 0x1000
36#define TX_TIMEOUT 500000
37
38/* Rx Trigger level */
39static int rx_trigger_level = 56;
40module_param(rx_trigger_level, uint, 0444);
41MODULE_PARM_DESC(rx_trigger_level, "Rx trigger level, 1-63 bytes");
42
43/* Rx Timeout */
44static int rx_timeout = 10;
45module_param(rx_timeout, uint, 0444);
46MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
47
48/* Register offsets for the UART. */
49#define CDNS_UART_CR 0x00 /* Control Register */
50#define CDNS_UART_MR 0x04 /* Mode Register */
51#define CDNS_UART_IER 0x08 /* Interrupt Enable */
52#define CDNS_UART_IDR 0x0C /* Interrupt Disable */
53#define CDNS_UART_IMR 0x10 /* Interrupt Mask */
54#define CDNS_UART_ISR 0x14 /* Interrupt Status */
55#define CDNS_UART_BAUDGEN 0x18 /* Baud Rate Generator */
56#define CDNS_UART_RXTOUT 0x1C /* RX Timeout */
57#define CDNS_UART_RXWM 0x20 /* RX FIFO Trigger Level */
58#define CDNS_UART_MODEMCR 0x24 /* Modem Control */
59#define CDNS_UART_MODEMSR 0x28 /* Modem Status */
60#define CDNS_UART_SR 0x2C /* Channel Status */
61#define CDNS_UART_FIFO 0x30 /* FIFO */
62#define CDNS_UART_BAUDDIV 0x34 /* Baud Rate Divider */
63#define CDNS_UART_FLOWDEL 0x38 /* Flow Delay */
64#define CDNS_UART_IRRX_PWIDTH 0x3C /* IR Min Received Pulse Width */
65#define CDNS_UART_IRTX_PWIDTH 0x40 /* IR Transmitted pulse Width */
66#define CDNS_UART_TXWM 0x44 /* TX FIFO Trigger Level */
67#define CDNS_UART_RXBS 0x48 /* RX FIFO byte status register */
68
69/* Control Register Bit Definitions */
70#define CDNS_UART_CR_STOPBRK 0x00000100 /* Stop TX break */
71#define CDNS_UART_CR_STARTBRK 0x00000080 /* Set TX break */
72#define CDNS_UART_CR_TX_DIS 0x00000020 /* TX disabled. */
73#define CDNS_UART_CR_TX_EN 0x00000010 /* TX enabled */
74#define CDNS_UART_CR_RX_DIS 0x00000008 /* RX disabled. */
75#define CDNS_UART_CR_RX_EN 0x00000004 /* RX enabled */
76#define CDNS_UART_CR_TXRST 0x00000002 /* TX logic reset */
77#define CDNS_UART_CR_RXRST 0x00000001 /* RX logic reset */
78#define CDNS_UART_CR_RST_TO 0x00000040 /* Restart Timeout Counter */
79#define CDNS_UART_RXBS_PARITY 0x00000001 /* Parity error status */
80#define CDNS_UART_RXBS_FRAMING 0x00000002 /* Framing error status */
81#define CDNS_UART_RXBS_BRK 0x00000004 /* Overrun error status */
82
83/*
84 * Mode Register:
85 * The mode register (MR) defines the mode of transfer as well as the data
86 * format. If this register is modified during transmission or reception,
87 * data validity cannot be guaranteed.
88 */
89#define CDNS_UART_MR_CLKSEL 0x00000001 /* Pre-scalar selection */
90#define CDNS_UART_MR_CHMODE_L_LOOP 0x00000200 /* Local loop back mode */
91#define CDNS_UART_MR_CHMODE_NORM 0x00000000 /* Normal mode */
92#define CDNS_UART_MR_CHMODE_MASK 0x00000300 /* Mask for mode bits */
93
94#define CDNS_UART_MR_STOPMODE_2_BIT 0x00000080 /* 2 stop bits */
95#define CDNS_UART_MR_STOPMODE_1_BIT 0x00000000 /* 1 stop bit */
96
97#define CDNS_UART_MR_PARITY_NONE 0x00000020 /* No parity mode */
98#define CDNS_UART_MR_PARITY_MARK 0x00000018 /* Mark parity mode */
99#define CDNS_UART_MR_PARITY_SPACE 0x00000010 /* Space parity mode */
100#define CDNS_UART_MR_PARITY_ODD 0x00000008 /* Odd parity mode */
101#define CDNS_UART_MR_PARITY_EVEN 0x00000000 /* Even parity mode */
102
103#define CDNS_UART_MR_CHARLEN_6_BIT 0x00000006 /* 6 bits data */
104#define CDNS_UART_MR_CHARLEN_7_BIT 0x00000004 /* 7 bits data */
105#define CDNS_UART_MR_CHARLEN_8_BIT 0x00000000 /* 8 bits data */
106
107/*
108 * Interrupt Registers:
109 * Interrupt control logic uses the interrupt enable register (IER) and the
110 * interrupt disable register (IDR) to set the value of the bits in the
111 * interrupt mask register (IMR). The IMR determines whether to pass an
112 * interrupt to the interrupt status register (ISR).
113 * Writing a 1 to IER Enables an interrupt, writing a 1 to IDR disables an
114 * interrupt. IMR and ISR are read only, and IER and IDR are write only.
115 * Reading either IER or IDR returns 0x00.
116 * All four registers have the same bit definitions.
117 */
118#define CDNS_UART_IXR_TOUT 0x00000100 /* RX Timeout error interrupt */
119#define CDNS_UART_IXR_PARITY 0x00000080 /* Parity error interrupt */
120#define CDNS_UART_IXR_FRAMING 0x00000040 /* Framing error interrupt */
121#define CDNS_UART_IXR_OVERRUN 0x00000020 /* Overrun error interrupt */
122#define CDNS_UART_IXR_TXFULL 0x00000010 /* TX FIFO Full interrupt */
123#define CDNS_UART_IXR_TXEMPTY 0x00000008 /* TX FIFO empty interrupt */
124#define CDNS_UART_ISR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt */
125#define CDNS_UART_IXR_RXTRIG 0x00000001 /* RX FIFO trigger interrupt */
126#define CDNS_UART_IXR_RXFULL 0x00000004 /* RX FIFO full interrupt. */
127#define CDNS_UART_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
128#define CDNS_UART_IXR_RXMASK 0x000021e7 /* Valid RX bit mask */
129
130 /*
131 * Do not enable parity error interrupt for the following
132 * reason: When parity error interrupt is enabled, each Rx
133 * parity error always results in 2 events. The first one
134 * being parity error interrupt and the second one with a
135 * proper Rx interrupt with the incoming data. Disabling
136 * parity error interrupt ensures better handling of parity
137 * error events. With this change, for a parity error case, we
138 * get a Rx interrupt with parity error set in ISR register
139 * and we still handle parity errors in the desired way.
140 */
141
142#define CDNS_UART_RX_IRQS (CDNS_UART_IXR_FRAMING | \
143 CDNS_UART_IXR_OVERRUN | \
144 CDNS_UART_IXR_RXTRIG | \
145 CDNS_UART_IXR_TOUT)
146
147/* Goes in read_status_mask for break detection as the HW doesn't do it*/
148#define CDNS_UART_IXR_BRK 0x00002000
149
150#define CDNS_UART_RXBS_SUPPORT BIT(1)
151/*
152 * Modem Control register:
153 * The read/write Modem Control register controls the interface with the modem
154 * or data set, or a peripheral device emulating a modem.
155 */
156#define CDNS_UART_MODEMCR_FCM 0x00000020 /* Automatic flow control mode */
157#define CDNS_UART_MODEMCR_RTS 0x00000002 /* Request to send output control */
158#define CDNS_UART_MODEMCR_DTR 0x00000001 /* Data Terminal Ready */
159
160/*
161 * Modem Status register:
162 * The read/write Modem Status register reports the interface with the modem
163 * or data set, or a peripheral device emulating a modem.
164 */
165#define CDNS_UART_MODEMSR_DCD BIT(7) /* Data Carrier Detect */
166#define CDNS_UART_MODEMSR_RI BIT(6) /* Ting Indicator */
167#define CDNS_UART_MODEMSR_DSR BIT(5) /* Data Set Ready */
168#define CDNS_UART_MODEMSR_CTS BIT(4) /* Clear To Send */
169
170/*
171 * Channel Status Register:
172 * The channel status register (CSR) is provided to enable the control logic
173 * to monitor the status of bits in the channel interrupt status register,
174 * even if these are masked out by the interrupt mask register.
175 */
176#define CDNS_UART_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
177#define CDNS_UART_SR_TXEMPTY 0x00000008 /* TX FIFO empty */
178#define CDNS_UART_SR_TXFULL 0x00000010 /* TX FIFO full */
179#define CDNS_UART_SR_RXTRIG 0x00000001 /* Rx Trigger */
180#define CDNS_UART_SR_TACTIVE 0x00000800 /* TX state machine active */
181
182/* baud dividers min/max values */
183#define CDNS_UART_BDIV_MIN 4
184#define CDNS_UART_BDIV_MAX 255
185#define CDNS_UART_CD_MAX 65535
186#define UART_AUTOSUSPEND_TIMEOUT 3000
187
188/**
189 * struct cdns_uart - device data
190 * @port: Pointer to the UART port
191 * @uartclk: Reference clock
192 * @pclk: APB clock
193 * @cdns_uart_driver: Pointer to UART driver
194 * @baud: Current baud rate
195 * @clk_rate_change_nb: Notifier block for clock changes
196 * @quirks: Flags for RXBS support.
197 * @cts_override: Modem control state override
198 * @gpiod_rts: Pointer to the gpio descriptor
199 * @rs485_tx_started: RS485 tx state
200 * @tx_timer: Timer for tx
201 */
202struct cdns_uart {
203 struct uart_port *port;
204 struct clk *uartclk;
205 struct clk *pclk;
206 struct uart_driver *cdns_uart_driver;
207 unsigned int baud;
208 struct notifier_block clk_rate_change_nb;
209 u32 quirks;
210 bool cts_override;
211 struct gpio_desc *gpiod_rts;
212 bool rs485_tx_started;
213 struct hrtimer tx_timer;
214};
215struct cdns_platform_data {
216 u32 quirks;
217};
218
219struct serial_rs485 cdns_rs485_supported = {
220 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
221 SER_RS485_RTS_AFTER_SEND,
222 .delay_rts_before_send = 1,
223 .delay_rts_after_send = 1,
224};
225
226#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
227 clk_rate_change_nb)
228
229/**
230 * cdns_uart_handle_rx - Handle the received bytes along with Rx errors.
231 * @dev_id: Id of the UART port
232 * @isrstatus: The interrupt status register value as read
233 * Return: None
234 */
235static void cdns_uart_handle_rx(void *dev_id, unsigned int isrstatus)
236{
237 struct uart_port *port = (struct uart_port *)dev_id;
238 struct cdns_uart *cdns_uart = port->private_data;
239 unsigned int data;
240 unsigned int rxbs_status = 0;
241 unsigned int status_mask;
242 unsigned int framerrprocessed = 0;
243 char status = TTY_NORMAL;
244 bool is_rxbs_support;
245
246 is_rxbs_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
247
248 while ((readl(port->membase + CDNS_UART_SR) &
249 CDNS_UART_SR_RXEMPTY) != CDNS_UART_SR_RXEMPTY) {
250 if (is_rxbs_support)
251 rxbs_status = readl(port->membase + CDNS_UART_RXBS);
252 data = readl(port->membase + CDNS_UART_FIFO);
253 port->icount.rx++;
254 /*
255 * There is no hardware break detection in Zynq, so we interpret
256 * framing error with all-zeros data as a break sequence.
257 * Most of the time, there's another non-zero byte at the
258 * end of the sequence.
259 */
260 if (!is_rxbs_support && (isrstatus & CDNS_UART_IXR_FRAMING)) {
261 if (!data) {
262 port->read_status_mask |= CDNS_UART_IXR_BRK;
263 framerrprocessed = 1;
264 continue;
265 }
266 }
267 if (is_rxbs_support && (rxbs_status & CDNS_UART_RXBS_BRK)) {
268 port->icount.brk++;
269 status = TTY_BREAK;
270 if (uart_handle_break(port))
271 continue;
272 }
273
274 isrstatus &= port->read_status_mask;
275 isrstatus &= ~port->ignore_status_mask;
276 status_mask = port->read_status_mask;
277 status_mask &= ~port->ignore_status_mask;
278
279 if (data &&
280 (port->read_status_mask & CDNS_UART_IXR_BRK)) {
281 port->read_status_mask &= ~CDNS_UART_IXR_BRK;
282 port->icount.brk++;
283 if (uart_handle_break(port))
284 continue;
285 }
286
287 if (uart_handle_sysrq_char(port, data))
288 continue;
289
290 if (is_rxbs_support) {
291 if ((rxbs_status & CDNS_UART_RXBS_PARITY)
292 && (status_mask & CDNS_UART_IXR_PARITY)) {
293 port->icount.parity++;
294 status = TTY_PARITY;
295 }
296 if ((rxbs_status & CDNS_UART_RXBS_FRAMING)
297 && (status_mask & CDNS_UART_IXR_PARITY)) {
298 port->icount.frame++;
299 status = TTY_FRAME;
300 }
301 } else {
302 if (isrstatus & CDNS_UART_IXR_PARITY) {
303 port->icount.parity++;
304 status = TTY_PARITY;
305 }
306 if ((isrstatus & CDNS_UART_IXR_FRAMING) &&
307 !framerrprocessed) {
308 port->icount.frame++;
309 status = TTY_FRAME;
310 }
311 }
312 if (isrstatus & CDNS_UART_IXR_OVERRUN) {
313 port->icount.overrun++;
314 tty_insert_flip_char(&port->state->port, 0,
315 TTY_OVERRUN);
316 }
317 tty_insert_flip_char(&port->state->port, data, status);
318 isrstatus = 0;
319 }
320
321 tty_flip_buffer_push(&port->state->port);
322}
323
324/**
325 * cdns_rts_gpio_enable - Configure RTS/GPIO to high/low
326 * @cdns_uart: Handle to the cdns_uart
327 * @enable: Value to be set to RTS/GPIO
328 */
329static void cdns_rts_gpio_enable(struct cdns_uart *cdns_uart, bool enable)
330{
331 u32 val;
332
333 if (cdns_uart->gpiod_rts) {
334 gpiod_set_value(cdns_uart->gpiod_rts, enable);
335 } else {
336 val = readl(cdns_uart->port->membase + CDNS_UART_MODEMCR);
337 if (enable)
338 val |= CDNS_UART_MODEMCR_RTS;
339 else
340 val &= ~CDNS_UART_MODEMCR_RTS;
341 writel(val, cdns_uart->port->membase + CDNS_UART_MODEMCR);
342 }
343}
344
345/**
346 * cdns_rs485_tx_setup - Tx setup specific to rs485
347 * @cdns_uart: Handle to the cdns_uart
348 */
349static void cdns_rs485_tx_setup(struct cdns_uart *cdns_uart)
350{
351 bool enable;
352
353 enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_ON_SEND;
354 cdns_rts_gpio_enable(cdns_uart, enable);
355
356 cdns_uart->rs485_tx_started = true;
357}
358
359/**
360 * cdns_rs485_rx_setup - Rx setup specific to rs485
361 * @cdns_uart: Handle to the cdns_uart
362 */
363static void cdns_rs485_rx_setup(struct cdns_uart *cdns_uart)
364{
365 bool enable;
366
367 enable = cdns_uart->port->rs485.flags & SER_RS485_RTS_AFTER_SEND;
368 cdns_rts_gpio_enable(cdns_uart, enable);
369
370 cdns_uart->rs485_tx_started = false;
371}
372
373/**
374 * cdns_uart_tx_empty - Check whether TX is empty
375 * @port: Handle to the uart port structure
376 *
377 * Return: TIOCSER_TEMT on success, 0 otherwise
378 */
379static unsigned int cdns_uart_tx_empty(struct uart_port *port)
380{
381 unsigned int status;
382
383 status = readl(port->membase + CDNS_UART_SR);
384 status &= (CDNS_UART_SR_TXEMPTY | CDNS_UART_SR_TACTIVE);
385 return (status == CDNS_UART_SR_TXEMPTY) ? TIOCSER_TEMT : 0;
386}
387
388/**
389 * cdns_rs485_rx_callback - Timer rx callback handler for rs485.
390 * @t: Handle to the hrtimer structure
391 */
392static enum hrtimer_restart cdns_rs485_rx_callback(struct hrtimer *t)
393{
394 struct cdns_uart *cdns_uart = container_of(t, struct cdns_uart, tx_timer);
395
396 /*
397 * Default Rx should be setup, because Rx signaling path
398 * need to enable to receive data.
399 */
400 cdns_rs485_rx_setup(cdns_uart);
401
402 return HRTIMER_NORESTART;
403}
404
405/**
406 * cdns_calc_after_tx_delay - calculate delay required for after tx.
407 * @cdns_uart: Handle to the cdns_uart
408 */
409static u64 cdns_calc_after_tx_delay(struct cdns_uart *cdns_uart)
410{
411 /*
412 * Frame time + stop bit time + rs485.delay_rts_after_send
413 */
414 return cdns_uart->port->frame_time
415 + DIV_ROUND_UP(cdns_uart->port->frame_time, 7)
416 + (u64)cdns_uart->port->rs485.delay_rts_after_send * NSEC_PER_MSEC;
417}
418
419/**
420 * cdns_uart_handle_tx - Handle the bytes to be transmitted.
421 * @dev_id: Id of the UART port
422 * Return: None
423 */
424static void cdns_uart_handle_tx(void *dev_id)
425{
426 struct uart_port *port = (struct uart_port *)dev_id;
427 struct cdns_uart *cdns_uart = port->private_data;
428 struct circ_buf *xmit = &port->state->xmit;
429 unsigned int numbytes;
430
431 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
432 /* Disable the TX Empty interrupt */
433 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IDR);
434 return;
435 }
436
437 numbytes = port->fifosize;
438 while (numbytes && !uart_circ_empty(xmit) &&
439 !(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)) {
440
441 writel(xmit->buf[xmit->tail], port->membase + CDNS_UART_FIFO);
442 uart_xmit_advance(port, 1);
443 numbytes--;
444 }
445
446 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
447 uart_write_wakeup(port);
448
449 /* Enable the TX Empty interrupt */
450 writel(CDNS_UART_IXR_TXEMPTY, cdns_uart->port->membase + CDNS_UART_IER);
451
452 if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED &&
453 (uart_circ_empty(xmit) || uart_tx_stopped(port))) {
454 cdns_uart->tx_timer.function = &cdns_rs485_rx_callback;
455 hrtimer_start(&cdns_uart->tx_timer,
456 ns_to_ktime(cdns_calc_after_tx_delay(cdns_uart)), HRTIMER_MODE_REL);
457 }
458}
459
460/**
461 * cdns_uart_isr - Interrupt handler
462 * @irq: Irq number
463 * @dev_id: Id of the port
464 *
465 * Return: IRQHANDLED
466 */
467static irqreturn_t cdns_uart_isr(int irq, void *dev_id)
468{
469 struct uart_port *port = (struct uart_port *)dev_id;
470 unsigned int isrstatus;
471
472 uart_port_lock(port);
473
474 /* Read the interrupt status register to determine which
475 * interrupt(s) is/are active and clear them.
476 */
477 isrstatus = readl(port->membase + CDNS_UART_ISR);
478 writel(isrstatus, port->membase + CDNS_UART_ISR);
479
480 if (isrstatus & CDNS_UART_IXR_TXEMPTY) {
481 cdns_uart_handle_tx(dev_id);
482 isrstatus &= ~CDNS_UART_IXR_TXEMPTY;
483 }
484
485 isrstatus &= port->read_status_mask;
486 isrstatus &= ~port->ignore_status_mask;
487 /*
488 * Skip RX processing if RX is disabled as RXEMPTY will never be set
489 * as read bytes will not be removed from the FIFO.
490 */
491 if (isrstatus & CDNS_UART_IXR_RXMASK &&
492 !(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_RX_DIS))
493 cdns_uart_handle_rx(dev_id, isrstatus);
494
495 uart_port_unlock(port);
496 return IRQ_HANDLED;
497}
498
499/**
500 * cdns_uart_calc_baud_divs - Calculate baud rate divisors
501 * @clk: UART module input clock
502 * @baud: Desired baud rate
503 * @rbdiv: BDIV value (return value)
504 * @rcd: CD value (return value)
505 * @div8: Value for clk_sel bit in mod (return value)
506 * Return: baud rate, requested baud when possible, or actual baud when there
507 * was too much error, zero if no valid divisors are found.
508 *
509 * Formula to obtain baud rate is
510 * baud_tx/rx rate = clk/CD * (BDIV + 1)
511 * input_clk = (Uart User Defined Clock or Apb Clock)
512 * depends on UCLKEN in MR Reg
513 * clk = input_clk or input_clk/8;
514 * depends on CLKS in MR reg
515 * CD and BDIV depends on values in
516 * baud rate generate register
517 * baud rate clock divisor register
518 */
519static unsigned int cdns_uart_calc_baud_divs(unsigned int clk,
520 unsigned int baud, u32 *rbdiv, u32 *rcd, int *div8)
521{
522 u32 cd, bdiv;
523 unsigned int calc_baud;
524 unsigned int bestbaud = 0;
525 unsigned int bauderror;
526 unsigned int besterror = ~0;
527
528 if (baud < clk / ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX)) {
529 *div8 = 1;
530 clk /= 8;
531 } else {
532 *div8 = 0;
533 }
534
535 for (bdiv = CDNS_UART_BDIV_MIN; bdiv <= CDNS_UART_BDIV_MAX; bdiv++) {
536 cd = DIV_ROUND_CLOSEST(clk, baud * (bdiv + 1));
537 if (cd < 1 || cd > CDNS_UART_CD_MAX)
538 continue;
539
540 calc_baud = clk / (cd * (bdiv + 1));
541
542 if (baud > calc_baud)
543 bauderror = baud - calc_baud;
544 else
545 bauderror = calc_baud - baud;
546
547 if (besterror > bauderror) {
548 *rbdiv = bdiv;
549 *rcd = cd;
550 bestbaud = calc_baud;
551 besterror = bauderror;
552 }
553 }
554 /* use the values when percent error is acceptable */
555 if (((besterror * 100) / baud) < 3)
556 bestbaud = baud;
557
558 return bestbaud;
559}
560
561/**
562 * cdns_uart_set_baud_rate - Calculate and set the baud rate
563 * @port: Handle to the uart port structure
564 * @baud: Baud rate to set
565 * Return: baud rate, requested baud when possible, or actual baud when there
566 * was too much error, zero if no valid divisors are found.
567 */
568static unsigned int cdns_uart_set_baud_rate(struct uart_port *port,
569 unsigned int baud)
570{
571 unsigned int calc_baud;
572 u32 cd = 0, bdiv = 0;
573 u32 mreg;
574 int div8;
575 struct cdns_uart *cdns_uart = port->private_data;
576
577 calc_baud = cdns_uart_calc_baud_divs(port->uartclk, baud, &bdiv, &cd,
578 &div8);
579
580 /* Write new divisors to hardware */
581 mreg = readl(port->membase + CDNS_UART_MR);
582 if (div8)
583 mreg |= CDNS_UART_MR_CLKSEL;
584 else
585 mreg &= ~CDNS_UART_MR_CLKSEL;
586 writel(mreg, port->membase + CDNS_UART_MR);
587 writel(cd, port->membase + CDNS_UART_BAUDGEN);
588 writel(bdiv, port->membase + CDNS_UART_BAUDDIV);
589 cdns_uart->baud = baud;
590
591 return calc_baud;
592}
593
594#ifdef CONFIG_COMMON_CLK
595/**
596 * cdns_uart_clk_notifier_cb - Clock notifier callback
597 * @nb: Notifier block
598 * @event: Notify event
599 * @data: Notifier data
600 * Return: NOTIFY_OK or NOTIFY_DONE on success, NOTIFY_BAD on error.
601 */
602static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
603 unsigned long event, void *data)
604{
605 u32 ctrl_reg;
606 struct uart_port *port;
607 int locked = 0;
608 struct clk_notifier_data *ndata = data;
609 struct cdns_uart *cdns_uart = to_cdns_uart(nb);
610 unsigned long flags;
611
612 port = cdns_uart->port;
613 if (port->suspended)
614 return NOTIFY_OK;
615
616 switch (event) {
617 case PRE_RATE_CHANGE:
618 {
619 u32 bdiv, cd;
620 int div8;
621
622 /*
623 * Find out if current baud-rate can be achieved with new clock
624 * frequency.
625 */
626 if (!cdns_uart_calc_baud_divs(ndata->new_rate, cdns_uart->baud,
627 &bdiv, &cd, &div8)) {
628 dev_warn(port->dev, "clock rate change rejected\n");
629 return NOTIFY_BAD;
630 }
631
632 uart_port_lock_irqsave(cdns_uart->port, &flags);
633
634 /* Disable the TX and RX to set baud rate */
635 ctrl_reg = readl(port->membase + CDNS_UART_CR);
636 ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
637 writel(ctrl_reg, port->membase + CDNS_UART_CR);
638
639 uart_port_unlock_irqrestore(cdns_uart->port, flags);
640
641 return NOTIFY_OK;
642 }
643 case POST_RATE_CHANGE:
644 /*
645 * Set clk dividers to generate correct baud with new clock
646 * frequency.
647 */
648
649 uart_port_lock_irqsave(cdns_uart->port, &flags);
650
651 locked = 1;
652 port->uartclk = ndata->new_rate;
653
654 cdns_uart->baud = cdns_uart_set_baud_rate(cdns_uart->port,
655 cdns_uart->baud);
656 fallthrough;
657 case ABORT_RATE_CHANGE:
658 if (!locked)
659 uart_port_lock_irqsave(cdns_uart->port, &flags);
660
661 /* Set TX/RX Reset */
662 ctrl_reg = readl(port->membase + CDNS_UART_CR);
663 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
664 writel(ctrl_reg, port->membase + CDNS_UART_CR);
665
666 while (readl(port->membase + CDNS_UART_CR) &
667 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
668 cpu_relax();
669
670 /*
671 * Clear the RX disable and TX disable bits and then set the TX
672 * enable bit and RX enable bit to enable the transmitter and
673 * receiver.
674 */
675 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
676 ctrl_reg = readl(port->membase + CDNS_UART_CR);
677 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
678 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
679 writel(ctrl_reg, port->membase + CDNS_UART_CR);
680
681 uart_port_unlock_irqrestore(cdns_uart->port, flags);
682
683 return NOTIFY_OK;
684 default:
685 return NOTIFY_DONE;
686 }
687}
688#endif
689
690/**
691 * cdns_rs485_tx_callback - Timer tx callback handler for rs485.
692 * @t: Handle to the hrtimer structure
693 */
694static enum hrtimer_restart cdns_rs485_tx_callback(struct hrtimer *t)
695{
696 struct cdns_uart *cdns_uart = container_of(t, struct cdns_uart, tx_timer);
697
698 uart_port_lock(cdns_uart->port);
699 cdns_uart_handle_tx(cdns_uart->port);
700 uart_port_unlock(cdns_uart->port);
701
702 return HRTIMER_NORESTART;
703}
704
705/**
706 * cdns_uart_start_tx - Start transmitting bytes
707 * @port: Handle to the uart port structure
708 */
709static void cdns_uart_start_tx(struct uart_port *port)
710{
711 unsigned int status;
712 struct cdns_uart *cdns_uart = port->private_data;
713
714 if (uart_tx_stopped(port))
715 return;
716
717 /*
718 * Set the TX enable bit and clear the TX disable bit to enable the
719 * transmitter.
720 */
721 status = readl(port->membase + CDNS_UART_CR);
722 status &= ~CDNS_UART_CR_TX_DIS;
723 status |= CDNS_UART_CR_TX_EN;
724 writel(status, port->membase + CDNS_UART_CR);
725
726 if (uart_circ_empty(&port->state->xmit))
727 return;
728
729 /* Clear the TX Empty interrupt */
730 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR);
731
732 if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED) {
733 if (!cdns_uart->rs485_tx_started) {
734 cdns_uart->tx_timer.function = &cdns_rs485_tx_callback;
735 cdns_rs485_tx_setup(cdns_uart);
736 return hrtimer_start(&cdns_uart->tx_timer,
737 ms_to_ktime(port->rs485.delay_rts_before_send),
738 HRTIMER_MODE_REL);
739 }
740 }
741 cdns_uart_handle_tx(port);
742}
743
744/**
745 * cdns_uart_stop_tx - Stop TX
746 * @port: Handle to the uart port structure
747 */
748static void cdns_uart_stop_tx(struct uart_port *port)
749{
750 unsigned int regval;
751 struct cdns_uart *cdns_uart = port->private_data;
752
753 if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
754 cdns_rs485_rx_setup(cdns_uart);
755
756 regval = readl(port->membase + CDNS_UART_CR);
757 regval |= CDNS_UART_CR_TX_DIS;
758 /* Disable the transmitter */
759 writel(regval, port->membase + CDNS_UART_CR);
760}
761
762/**
763 * cdns_uart_stop_rx - Stop RX
764 * @port: Handle to the uart port structure
765 */
766static void cdns_uart_stop_rx(struct uart_port *port)
767{
768 unsigned int regval;
769
770 /* Disable RX IRQs */
771 writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IDR);
772
773 /* Disable the receiver */
774 regval = readl(port->membase + CDNS_UART_CR);
775 regval |= CDNS_UART_CR_RX_DIS;
776 writel(regval, port->membase + CDNS_UART_CR);
777}
778
779/**
780 * cdns_uart_break_ctl - Based on the input ctl we have to start or stop
781 * transmitting char breaks
782 * @port: Handle to the uart port structure
783 * @ctl: Value based on which start or stop decision is taken
784 */
785static void cdns_uart_break_ctl(struct uart_port *port, int ctl)
786{
787 unsigned int status;
788 unsigned long flags;
789
790 uart_port_lock_irqsave(port, &flags);
791
792 status = readl(port->membase + CDNS_UART_CR);
793
794 if (ctl == -1)
795 writel(CDNS_UART_CR_STARTBRK | (~CDNS_UART_CR_STOPBRK & status),
796 port->membase + CDNS_UART_CR);
797 else {
798 if ((status & CDNS_UART_CR_STOPBRK) == 0)
799 writel(CDNS_UART_CR_STOPBRK | status,
800 port->membase + CDNS_UART_CR);
801 }
802 uart_port_unlock_irqrestore(port, flags);
803}
804
805/**
806 * cdns_uart_set_termios - termios operations, handling data length, parity,
807 * stop bits, flow control, baud rate
808 * @port: Handle to the uart port structure
809 * @termios: Handle to the input termios structure
810 * @old: Values of the previously saved termios structure
811 */
812static void cdns_uart_set_termios(struct uart_port *port,
813 struct ktermios *termios,
814 const struct ktermios *old)
815{
816 u32 cval = 0;
817 unsigned int baud, minbaud, maxbaud;
818 unsigned long flags;
819 unsigned int ctrl_reg, mode_reg;
820
821 uart_port_lock_irqsave(port, &flags);
822
823 /* Disable the TX and RX to set baud rate */
824 ctrl_reg = readl(port->membase + CDNS_UART_CR);
825 ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
826 writel(ctrl_reg, port->membase + CDNS_UART_CR);
827
828 /*
829 * Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
830 * min and max baud should be calculated here based on port->uartclk.
831 * this way we get a valid baud and can safely call set_baud()
832 */
833 minbaud = port->uartclk /
834 ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX * 8);
835 maxbaud = port->uartclk / (CDNS_UART_BDIV_MIN + 1);
836 baud = uart_get_baud_rate(port, termios, old, minbaud, maxbaud);
837 baud = cdns_uart_set_baud_rate(port, baud);
838 if (tty_termios_baud_rate(termios))
839 tty_termios_encode_baud_rate(termios, baud, baud);
840
841 /* Update the per-port timeout. */
842 uart_update_timeout(port, termios->c_cflag, baud);
843
844 /* Set TX/RX Reset */
845 ctrl_reg = readl(port->membase + CDNS_UART_CR);
846 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
847 writel(ctrl_reg, port->membase + CDNS_UART_CR);
848
849 while (readl(port->membase + CDNS_UART_CR) &
850 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
851 cpu_relax();
852
853 /*
854 * Clear the RX disable and TX disable bits and then set the TX enable
855 * bit and RX enable bit to enable the transmitter and receiver.
856 */
857 ctrl_reg = readl(port->membase + CDNS_UART_CR);
858 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
859 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
860 writel(ctrl_reg, port->membase + CDNS_UART_CR);
861
862 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
863
864 port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
865 CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
866 port->ignore_status_mask = 0;
867
868 if (termios->c_iflag & INPCK)
869 port->read_status_mask |= CDNS_UART_IXR_PARITY |
870 CDNS_UART_IXR_FRAMING;
871
872 if (termios->c_iflag & IGNPAR)
873 port->ignore_status_mask |= CDNS_UART_IXR_PARITY |
874 CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
875
876 /* ignore all characters if CREAD is not set */
877 if ((termios->c_cflag & CREAD) == 0)
878 port->ignore_status_mask |= CDNS_UART_IXR_RXTRIG |
879 CDNS_UART_IXR_TOUT | CDNS_UART_IXR_PARITY |
880 CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
881
882 mode_reg = readl(port->membase + CDNS_UART_MR);
883
884 /* Handling Data Size */
885 switch (termios->c_cflag & CSIZE) {
886 case CS6:
887 cval |= CDNS_UART_MR_CHARLEN_6_BIT;
888 break;
889 case CS7:
890 cval |= CDNS_UART_MR_CHARLEN_7_BIT;
891 break;
892 default:
893 case CS8:
894 cval |= CDNS_UART_MR_CHARLEN_8_BIT;
895 termios->c_cflag &= ~CSIZE;
896 termios->c_cflag |= CS8;
897 break;
898 }
899
900 /* Handling Parity and Stop Bits length */
901 if (termios->c_cflag & CSTOPB)
902 cval |= CDNS_UART_MR_STOPMODE_2_BIT; /* 2 STOP bits */
903 else
904 cval |= CDNS_UART_MR_STOPMODE_1_BIT; /* 1 STOP bit */
905
906 if (termios->c_cflag & PARENB) {
907 /* Mark or Space parity */
908 if (termios->c_cflag & CMSPAR) {
909 if (termios->c_cflag & PARODD)
910 cval |= CDNS_UART_MR_PARITY_MARK;
911 else
912 cval |= CDNS_UART_MR_PARITY_SPACE;
913 } else {
914 if (termios->c_cflag & PARODD)
915 cval |= CDNS_UART_MR_PARITY_ODD;
916 else
917 cval |= CDNS_UART_MR_PARITY_EVEN;
918 }
919 } else {
920 cval |= CDNS_UART_MR_PARITY_NONE;
921 }
922 cval |= mode_reg & 1;
923 writel(cval, port->membase + CDNS_UART_MR);
924
925 cval = readl(port->membase + CDNS_UART_MODEMCR);
926 if (termios->c_cflag & CRTSCTS)
927 cval |= CDNS_UART_MODEMCR_FCM;
928 else
929 cval &= ~CDNS_UART_MODEMCR_FCM;
930 writel(cval, port->membase + CDNS_UART_MODEMCR);
931
932 uart_port_unlock_irqrestore(port, flags);
933}
934
935/**
936 * cdns_uart_startup - Called when an application opens a cdns_uart port
937 * @port: Handle to the uart port structure
938 *
939 * Return: 0 on success, negative errno otherwise
940 */
941static int cdns_uart_startup(struct uart_port *port)
942{
943 struct cdns_uart *cdns_uart = port->private_data;
944 bool is_brk_support;
945 int ret;
946 unsigned long flags;
947 unsigned int status = 0;
948
949 is_brk_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
950
951 uart_port_lock_irqsave(port, &flags);
952
953 /* Disable the TX and RX */
954 writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
955 port->membase + CDNS_UART_CR);
956
957 /* Set the Control Register with TX/RX Enable, TX/RX Reset,
958 * no break chars.
959 */
960 writel(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST,
961 port->membase + CDNS_UART_CR);
962
963 while (readl(port->membase + CDNS_UART_CR) &
964 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
965 cpu_relax();
966
967 if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
968 cdns_rs485_rx_setup(cdns_uart);
969
970 /*
971 * Clear the RX disable bit and then set the RX enable bit to enable
972 * the receiver.
973 */
974 status = readl(port->membase + CDNS_UART_CR);
975 status &= ~CDNS_UART_CR_RX_DIS;
976 status |= CDNS_UART_CR_RX_EN;
977 writel(status, port->membase + CDNS_UART_CR);
978
979 /* Set the Mode Register with normal mode,8 data bits,1 stop bit,
980 * no parity.
981 */
982 writel(CDNS_UART_MR_CHMODE_NORM | CDNS_UART_MR_STOPMODE_1_BIT
983 | CDNS_UART_MR_PARITY_NONE | CDNS_UART_MR_CHARLEN_8_BIT,
984 port->membase + CDNS_UART_MR);
985
986 /*
987 * Set the RX FIFO Trigger level to use most of the FIFO, but it
988 * can be tuned with a module parameter
989 */
990 writel(rx_trigger_level, port->membase + CDNS_UART_RXWM);
991
992 /*
993 * Receive Timeout register is enabled but it
994 * can be tuned with a module parameter
995 */
996 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
997
998 /* Clear out any pending interrupts before enabling them */
999 writel(readl(port->membase + CDNS_UART_ISR),
1000 port->membase + CDNS_UART_ISR);
1001
1002 uart_port_unlock_irqrestore(port, flags);
1003
1004 ret = request_irq(port->irq, cdns_uart_isr, 0, CDNS_UART_NAME, port);
1005 if (ret) {
1006 dev_err(port->dev, "request_irq '%d' failed with %d\n",
1007 port->irq, ret);
1008 return ret;
1009 }
1010
1011 /* Set the Interrupt Registers with desired interrupts */
1012 if (is_brk_support)
1013 writel(CDNS_UART_RX_IRQS | CDNS_UART_IXR_BRK,
1014 port->membase + CDNS_UART_IER);
1015 else
1016 writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IER);
1017
1018 return 0;
1019}
1020
1021/**
1022 * cdns_uart_shutdown - Called when an application closes a cdns_uart port
1023 * @port: Handle to the uart port structure
1024 */
1025static void cdns_uart_shutdown(struct uart_port *port)
1026{
1027 int status;
1028 unsigned long flags;
1029 struct cdns_uart *cdns_uart = port->private_data;
1030
1031 if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED)
1032 hrtimer_cancel(&cdns_uart->tx_timer);
1033
1034 uart_port_lock_irqsave(port, &flags);
1035
1036 /* Disable interrupts */
1037 status = readl(port->membase + CDNS_UART_IMR);
1038 writel(status, port->membase + CDNS_UART_IDR);
1039 writel(0xffffffff, port->membase + CDNS_UART_ISR);
1040
1041 /* Disable the TX and RX */
1042 writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
1043 port->membase + CDNS_UART_CR);
1044
1045 uart_port_unlock_irqrestore(port, flags);
1046
1047 free_irq(port->irq, port);
1048}
1049
1050/**
1051 * cdns_uart_type - Set UART type to cdns_uart port
1052 * @port: Handle to the uart port structure
1053 *
1054 * Return: string on success, NULL otherwise
1055 */
1056static const char *cdns_uart_type(struct uart_port *port)
1057{
1058 return port->type == PORT_XUARTPS ? CDNS_UART_NAME : NULL;
1059}
1060
1061/**
1062 * cdns_uart_verify_port - Verify the port params
1063 * @port: Handle to the uart port structure
1064 * @ser: Handle to the structure whose members are compared
1065 *
1066 * Return: 0 on success, negative errno otherwise.
1067 */
1068static int cdns_uart_verify_port(struct uart_port *port,
1069 struct serial_struct *ser)
1070{
1071 if (ser->type != PORT_UNKNOWN && ser->type != PORT_XUARTPS)
1072 return -EINVAL;
1073 if (port->irq != ser->irq)
1074 return -EINVAL;
1075 if (ser->io_type != UPIO_MEM)
1076 return -EINVAL;
1077 if (port->iobase != ser->port)
1078 return -EINVAL;
1079 if (ser->hub6 != 0)
1080 return -EINVAL;
1081 return 0;
1082}
1083
1084/**
1085 * cdns_uart_request_port - Claim the memory region attached to cdns_uart port,
1086 * called when the driver adds a cdns_uart port via
1087 * uart_add_one_port()
1088 * @port: Handle to the uart port structure
1089 *
1090 * Return: 0 on success, negative errno otherwise.
1091 */
1092static int cdns_uart_request_port(struct uart_port *port)
1093{
1094 if (!request_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE,
1095 CDNS_UART_NAME)) {
1096 return -ENOMEM;
1097 }
1098
1099 port->membase = ioremap(port->mapbase, CDNS_UART_REGISTER_SPACE);
1100 if (!port->membase) {
1101 dev_err(port->dev, "Unable to map registers\n");
1102 release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
1103 return -ENOMEM;
1104 }
1105 return 0;
1106}
1107
1108/**
1109 * cdns_uart_release_port - Release UART port
1110 * @port: Handle to the uart port structure
1111 *
1112 * Release the memory region attached to a cdns_uart port. Called when the
1113 * driver removes a cdns_uart port via uart_remove_one_port().
1114 */
1115static void cdns_uart_release_port(struct uart_port *port)
1116{
1117 release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
1118 iounmap(port->membase);
1119 port->membase = NULL;
1120}
1121
1122/**
1123 * cdns_uart_config_port - Configure UART port
1124 * @port: Handle to the uart port structure
1125 * @flags: If any
1126 */
1127static void cdns_uart_config_port(struct uart_port *port, int flags)
1128{
1129 if (flags & UART_CONFIG_TYPE && cdns_uart_request_port(port) == 0)
1130 port->type = PORT_XUARTPS;
1131}
1132
1133/**
1134 * cdns_uart_get_mctrl - Get the modem control state
1135 * @port: Handle to the uart port structure
1136 *
1137 * Return: the modem control state
1138 */
1139static unsigned int cdns_uart_get_mctrl(struct uart_port *port)
1140{
1141 u32 val;
1142 unsigned int mctrl = 0;
1143 struct cdns_uart *cdns_uart_data = port->private_data;
1144
1145 if (cdns_uart_data->cts_override)
1146 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
1147
1148 val = readl(port->membase + CDNS_UART_MODEMSR);
1149 if (val & CDNS_UART_MODEMSR_CTS)
1150 mctrl |= TIOCM_CTS;
1151 if (val & CDNS_UART_MODEMSR_DSR)
1152 mctrl |= TIOCM_DSR;
1153 if (val & CDNS_UART_MODEMSR_RI)
1154 mctrl |= TIOCM_RNG;
1155 if (val & CDNS_UART_MODEMSR_DCD)
1156 mctrl |= TIOCM_CAR;
1157
1158 return mctrl;
1159}
1160
1161static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1162{
1163 u32 val;
1164 u32 mode_reg;
1165 struct cdns_uart *cdns_uart_data = port->private_data;
1166
1167 if (cdns_uart_data->cts_override)
1168 return;
1169
1170 val = readl(port->membase + CDNS_UART_MODEMCR);
1171 mode_reg = readl(port->membase + CDNS_UART_MR);
1172
1173 val &= ~(CDNS_UART_MODEMCR_RTS | CDNS_UART_MODEMCR_DTR);
1174 mode_reg &= ~CDNS_UART_MR_CHMODE_MASK;
1175
1176 if (mctrl & TIOCM_RTS)
1177 val |= CDNS_UART_MODEMCR_RTS;
1178 if (cdns_uart_data->gpiod_rts)
1179 gpiod_set_value(cdns_uart_data->gpiod_rts, !(mctrl & TIOCM_RTS));
1180 if (mctrl & TIOCM_DTR)
1181 val |= CDNS_UART_MODEMCR_DTR;
1182 if (mctrl & TIOCM_LOOP)
1183 mode_reg |= CDNS_UART_MR_CHMODE_L_LOOP;
1184 else
1185 mode_reg |= CDNS_UART_MR_CHMODE_NORM;
1186
1187 writel(val, port->membase + CDNS_UART_MODEMCR);
1188 writel(mode_reg, port->membase + CDNS_UART_MR);
1189}
1190
1191#ifdef CONFIG_CONSOLE_POLL
1192static int cdns_uart_poll_get_char(struct uart_port *port)
1193{
1194 int c;
1195 unsigned long flags;
1196
1197 uart_port_lock_irqsave(port, &flags);
1198
1199 /* Check if FIFO is empty */
1200 if (readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY)
1201 c = NO_POLL_CHAR;
1202 else /* Read a character */
1203 c = (unsigned char) readl(port->membase + CDNS_UART_FIFO);
1204
1205 uart_port_unlock_irqrestore(port, flags);
1206
1207 return c;
1208}
1209
1210static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c)
1211{
1212 unsigned long flags;
1213
1214 uart_port_lock_irqsave(port, &flags);
1215
1216 /* Wait until FIFO is empty */
1217 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1218 cpu_relax();
1219
1220 /* Write a character */
1221 writel(c, port->membase + CDNS_UART_FIFO);
1222
1223 /* Wait until FIFO is empty */
1224 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1225 cpu_relax();
1226
1227 uart_port_unlock_irqrestore(port, flags);
1228}
1229#endif
1230
1231static void cdns_uart_pm(struct uart_port *port, unsigned int state,
1232 unsigned int oldstate)
1233{
1234 switch (state) {
1235 case UART_PM_STATE_OFF:
1236 pm_runtime_mark_last_busy(port->dev);
1237 pm_runtime_put_autosuspend(port->dev);
1238 break;
1239 default:
1240 pm_runtime_get_sync(port->dev);
1241 break;
1242 }
1243}
1244
1245static const struct uart_ops cdns_uart_ops = {
1246 .set_mctrl = cdns_uart_set_mctrl,
1247 .get_mctrl = cdns_uart_get_mctrl,
1248 .start_tx = cdns_uart_start_tx,
1249 .stop_tx = cdns_uart_stop_tx,
1250 .stop_rx = cdns_uart_stop_rx,
1251 .tx_empty = cdns_uart_tx_empty,
1252 .break_ctl = cdns_uart_break_ctl,
1253 .set_termios = cdns_uart_set_termios,
1254 .startup = cdns_uart_startup,
1255 .shutdown = cdns_uart_shutdown,
1256 .pm = cdns_uart_pm,
1257 .type = cdns_uart_type,
1258 .verify_port = cdns_uart_verify_port,
1259 .request_port = cdns_uart_request_port,
1260 .release_port = cdns_uart_release_port,
1261 .config_port = cdns_uart_config_port,
1262#ifdef CONFIG_CONSOLE_POLL
1263 .poll_get_char = cdns_uart_poll_get_char,
1264 .poll_put_char = cdns_uart_poll_put_char,
1265#endif
1266};
1267
1268static struct uart_driver cdns_uart_uart_driver;
1269
1270#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1271/**
1272 * cdns_uart_console_putchar - write the character to the FIFO buffer
1273 * @port: Handle to the uart port structure
1274 * @ch: Character to be written
1275 */
1276static void cdns_uart_console_putchar(struct uart_port *port, unsigned char ch)
1277{
1278 unsigned int ctrl_reg;
1279 unsigned long timeout;
1280
1281 timeout = jiffies + msecs_to_jiffies(1000);
1282 while (1) {
1283 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1284 if (!(ctrl_reg & CDNS_UART_CR_TX_DIS))
1285 break;
1286 if (time_after(jiffies, timeout)) {
1287 dev_warn(port->dev,
1288 "timeout waiting for Enable\n");
1289 return;
1290 }
1291 cpu_relax();
1292 }
1293
1294 timeout = jiffies + msecs_to_jiffies(1000);
1295 while (1) {
1296 ctrl_reg = readl(port->membase + CDNS_UART_SR);
1297
1298 if (!(ctrl_reg & CDNS_UART_SR_TXFULL))
1299 break;
1300 if (time_after(jiffies, timeout)) {
1301 dev_warn(port->dev,
1302 "timeout waiting for TX fifo\n");
1303 return;
1304 }
1305 cpu_relax();
1306 }
1307 writel(ch, port->membase + CDNS_UART_FIFO);
1308}
1309
1310static void cdns_early_write(struct console *con, const char *s,
1311 unsigned int n)
1312{
1313 struct earlycon_device *dev = con->data;
1314
1315 uart_console_write(&dev->port, s, n, cdns_uart_console_putchar);
1316}
1317
1318static int __init cdns_early_console_setup(struct earlycon_device *device,
1319 const char *opt)
1320{
1321 struct uart_port *port = &device->port;
1322
1323 if (!port->membase)
1324 return -ENODEV;
1325
1326 /* initialise control register */
1327 writel(CDNS_UART_CR_TX_EN|CDNS_UART_CR_TXRST|CDNS_UART_CR_RXRST,
1328 port->membase + CDNS_UART_CR);
1329
1330 /* only set baud if specified on command line - otherwise
1331 * assume it has been initialized by a boot loader.
1332 */
1333 if (port->uartclk && device->baud) {
1334 u32 cd = 0, bdiv = 0;
1335 u32 mr;
1336 int div8;
1337
1338 cdns_uart_calc_baud_divs(port->uartclk, device->baud,
1339 &bdiv, &cd, &div8);
1340 mr = CDNS_UART_MR_PARITY_NONE;
1341 if (div8)
1342 mr |= CDNS_UART_MR_CLKSEL;
1343
1344 writel(mr, port->membase + CDNS_UART_MR);
1345 writel(cd, port->membase + CDNS_UART_BAUDGEN);
1346 writel(bdiv, port->membase + CDNS_UART_BAUDDIV);
1347 }
1348
1349 device->con->write = cdns_early_write;
1350
1351 return 0;
1352}
1353OF_EARLYCON_DECLARE(cdns, "xlnx,xuartps", cdns_early_console_setup);
1354OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup);
1355OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup);
1356OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
1357
1358
1359/* Static pointer to console port */
1360static struct uart_port *console_port;
1361
1362/**
1363 * cdns_uart_console_write - perform write operation
1364 * @co: Console handle
1365 * @s: Pointer to character array
1366 * @count: No of characters
1367 */
1368static void cdns_uart_console_write(struct console *co, const char *s,
1369 unsigned int count)
1370{
1371 struct uart_port *port = console_port;
1372 unsigned long flags;
1373 unsigned int imr, ctrl;
1374 int locked = 1;
1375
1376 if (port->sysrq)
1377 locked = 0;
1378 else if (oops_in_progress)
1379 locked = uart_port_trylock_irqsave(port, &flags);
1380 else
1381 uart_port_lock_irqsave(port, &flags);
1382
1383 /* save and disable interrupt */
1384 imr = readl(port->membase + CDNS_UART_IMR);
1385 writel(imr, port->membase + CDNS_UART_IDR);
1386
1387 /*
1388 * Make sure that the tx part is enabled. Set the TX enable bit and
1389 * clear the TX disable bit to enable the transmitter.
1390 */
1391 ctrl = readl(port->membase + CDNS_UART_CR);
1392 ctrl &= ~CDNS_UART_CR_TX_DIS;
1393 ctrl |= CDNS_UART_CR_TX_EN;
1394 writel(ctrl, port->membase + CDNS_UART_CR);
1395
1396 uart_console_write(port, s, count, cdns_uart_console_putchar);
1397 while (cdns_uart_tx_empty(port) != TIOCSER_TEMT)
1398 cpu_relax();
1399
1400 /* restore interrupt state */
1401 writel(imr, port->membase + CDNS_UART_IER);
1402
1403 if (locked)
1404 uart_port_unlock_irqrestore(port, flags);
1405}
1406
1407/**
1408 * cdns_uart_console_setup - Initialize the uart to default config
1409 * @co: Console handle
1410 * @options: Initial settings of uart
1411 *
1412 * Return: 0 on success, negative errno otherwise.
1413 */
1414static int cdns_uart_console_setup(struct console *co, char *options)
1415{
1416 struct uart_port *port = console_port;
1417
1418 int baud = 9600;
1419 int bits = 8;
1420 int parity = 'n';
1421 int flow = 'n';
1422 unsigned long time_out;
1423
1424 if (!port->membase) {
1425 pr_debug("console on " CDNS_UART_TTY_NAME "%i not present\n",
1426 co->index);
1427 return -ENODEV;
1428 }
1429
1430 if (options)
1431 uart_parse_options(options, &baud, &parity, &bits, &flow);
1432
1433 /* Wait for tx_empty before setting up the console */
1434 time_out = jiffies + usecs_to_jiffies(TX_TIMEOUT);
1435
1436 while (time_before(jiffies, time_out) &&
1437 cdns_uart_tx_empty(port) != TIOCSER_TEMT)
1438 cpu_relax();
1439
1440 return uart_set_options(port, co, baud, parity, bits, flow);
1441}
1442
1443static struct console cdns_uart_console = {
1444 .name = CDNS_UART_TTY_NAME,
1445 .write = cdns_uart_console_write,
1446 .device = uart_console_device,
1447 .setup = cdns_uart_console_setup,
1448 .flags = CON_PRINTBUFFER,
1449 .index = -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
1450 .data = &cdns_uart_uart_driver,
1451};
1452#endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
1453
1454#ifdef CONFIG_PM_SLEEP
1455/**
1456 * cdns_uart_suspend - suspend event
1457 * @device: Pointer to the device structure
1458 *
1459 * Return: 0
1460 */
1461static int cdns_uart_suspend(struct device *device)
1462{
1463 struct uart_port *port = dev_get_drvdata(device);
1464 struct cdns_uart *cdns_uart = port->private_data;
1465 int may_wake;
1466
1467 may_wake = device_may_wakeup(device);
1468
1469 if (console_suspend_enabled && uart_console(port) && may_wake) {
1470 unsigned long flags;
1471
1472 uart_port_lock_irqsave(port, &flags);
1473 /* Empty the receive FIFO 1st before making changes */
1474 while (!(readl(port->membase + CDNS_UART_SR) &
1475 CDNS_UART_SR_RXEMPTY))
1476 readl(port->membase + CDNS_UART_FIFO);
1477 /* set RX trigger level to 1 */
1478 writel(1, port->membase + CDNS_UART_RXWM);
1479 /* disable RX timeout interrups */
1480 writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IDR);
1481 uart_port_unlock_irqrestore(port, flags);
1482 }
1483
1484 /*
1485 * Call the API provided in serial_core.c file which handles
1486 * the suspend.
1487 */
1488 return uart_suspend_port(cdns_uart->cdns_uart_driver, port);
1489}
1490
1491/**
1492 * cdns_uart_resume - Resume after a previous suspend
1493 * @device: Pointer to the device structure
1494 *
1495 * Return: 0
1496 */
1497static int cdns_uart_resume(struct device *device)
1498{
1499 struct uart_port *port = dev_get_drvdata(device);
1500 struct cdns_uart *cdns_uart = port->private_data;
1501 unsigned long flags;
1502 u32 ctrl_reg;
1503 int may_wake;
1504 int ret;
1505
1506 may_wake = device_may_wakeup(device);
1507
1508 if (console_suspend_enabled && uart_console(port) && !may_wake) {
1509 ret = clk_enable(cdns_uart->pclk);
1510 if (ret)
1511 return ret;
1512
1513 ret = clk_enable(cdns_uart->uartclk);
1514 if (ret) {
1515 clk_disable(cdns_uart->pclk);
1516 return ret;
1517 }
1518
1519 uart_port_lock_irqsave(port, &flags);
1520
1521 /* Set TX/RX Reset */
1522 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1523 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
1524 writel(ctrl_reg, port->membase + CDNS_UART_CR);
1525 while (readl(port->membase + CDNS_UART_CR) &
1526 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
1527 cpu_relax();
1528
1529 /* restore rx timeout value */
1530 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
1531 /* Enable Tx/Rx */
1532 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1533 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
1534 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
1535 writel(ctrl_reg, port->membase + CDNS_UART_CR);
1536
1537 clk_disable(cdns_uart->uartclk);
1538 clk_disable(cdns_uart->pclk);
1539 uart_port_unlock_irqrestore(port, flags);
1540 } else {
1541 uart_port_lock_irqsave(port, &flags);
1542 /* restore original rx trigger level */
1543 writel(rx_trigger_level, port->membase + CDNS_UART_RXWM);
1544 /* enable RX timeout interrupt */
1545 writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IER);
1546 uart_port_unlock_irqrestore(port, flags);
1547 }
1548
1549 return uart_resume_port(cdns_uart->cdns_uart_driver, port);
1550}
1551#endif /* ! CONFIG_PM_SLEEP */
1552static int __maybe_unused cdns_runtime_suspend(struct device *dev)
1553{
1554 struct uart_port *port = dev_get_drvdata(dev);
1555 struct cdns_uart *cdns_uart = port->private_data;
1556
1557 clk_disable(cdns_uart->uartclk);
1558 clk_disable(cdns_uart->pclk);
1559 return 0;
1560};
1561
1562static int __maybe_unused cdns_runtime_resume(struct device *dev)
1563{
1564 struct uart_port *port = dev_get_drvdata(dev);
1565 struct cdns_uart *cdns_uart = port->private_data;
1566 int ret;
1567
1568 ret = clk_enable(cdns_uart->pclk);
1569 if (ret)
1570 return ret;
1571
1572 ret = clk_enable(cdns_uart->uartclk);
1573 if (ret) {
1574 clk_disable(cdns_uart->pclk);
1575 return ret;
1576 }
1577 return 0;
1578};
1579
1580static const struct dev_pm_ops cdns_uart_dev_pm_ops = {
1581 SET_SYSTEM_SLEEP_PM_OPS(cdns_uart_suspend, cdns_uart_resume)
1582 SET_RUNTIME_PM_OPS(cdns_runtime_suspend,
1583 cdns_runtime_resume, NULL)
1584};
1585
1586static const struct cdns_platform_data zynqmp_uart_def = {
1587 .quirks = CDNS_UART_RXBS_SUPPORT, };
1588
1589/* Match table for of_platform binding */
1590static const struct of_device_id cdns_uart_of_match[] = {
1591 { .compatible = "xlnx,xuartps", },
1592 { .compatible = "cdns,uart-r1p8", },
1593 { .compatible = "cdns,uart-r1p12", .data = &zynqmp_uart_def },
1594 { .compatible = "xlnx,zynqmp-uart", .data = &zynqmp_uart_def },
1595 {}
1596};
1597MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
1598
1599/* Temporary variable for storing number of instances */
1600static int instances;
1601
1602/**
1603 * cdns_rs485_config - Called when an application calls TIOCSRS485 ioctl.
1604 * @port: Pointer to the uart_port structure
1605 * @termios: Pointer to the ktermios structure
1606 * @rs485: Pointer to the serial_rs485 structure
1607 *
1608 * Return: 0
1609 */
1610static int cdns_rs485_config(struct uart_port *port, struct ktermios *termios,
1611 struct serial_rs485 *rs485)
1612{
1613 u32 val;
1614 struct cdns_uart *cdns_uart = port->private_data;
1615
1616 if (rs485->flags & SER_RS485_ENABLED) {
1617 dev_dbg(port->dev, "Setting UART to RS485\n");
1618 /* Make sure auto RTS is disabled */
1619 val = readl(port->membase + CDNS_UART_MODEMCR);
1620 val &= ~CDNS_UART_MODEMCR_FCM;
1621 writel(val, port->membase + CDNS_UART_MODEMCR);
1622
1623 /* Timer setup */
1624 hrtimer_init(&cdns_uart->tx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
1625 cdns_uart->tx_timer.function = &cdns_rs485_tx_callback;
1626
1627 /* Disable transmitter and make Rx setup*/
1628 cdns_uart_stop_tx(port);
1629 } else {
1630 hrtimer_cancel(&cdns_uart->tx_timer);
1631 }
1632 return 0;
1633}
1634
1635/**
1636 * cdns_uart_probe - Platform driver probe
1637 * @pdev: Pointer to the platform device structure
1638 *
1639 * Return: 0 on success, negative errno otherwise
1640 */
1641static int cdns_uart_probe(struct platform_device *pdev)
1642{
1643 int rc, id, irq;
1644 struct uart_port *port;
1645 struct resource *res;
1646 struct cdns_uart *cdns_uart_data;
1647 const struct of_device_id *match;
1648
1649 cdns_uart_data = devm_kzalloc(&pdev->dev, sizeof(*cdns_uart_data),
1650 GFP_KERNEL);
1651 if (!cdns_uart_data)
1652 return -ENOMEM;
1653 port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
1654 if (!port)
1655 return -ENOMEM;
1656
1657 /* Look for a serialN alias */
1658 id = of_alias_get_id(pdev->dev.of_node, "serial");
1659 if (id < 0)
1660 id = 0;
1661
1662 if (id >= CDNS_UART_NR_PORTS) {
1663 dev_err(&pdev->dev, "Cannot get uart_port structure\n");
1664 return -ENODEV;
1665 }
1666
1667 if (!cdns_uart_uart_driver.state) {
1668 cdns_uart_uart_driver.owner = THIS_MODULE;
1669 cdns_uart_uart_driver.driver_name = CDNS_UART_NAME;
1670 cdns_uart_uart_driver.dev_name = CDNS_UART_TTY_NAME;
1671 cdns_uart_uart_driver.major = CDNS_UART_MAJOR;
1672 cdns_uart_uart_driver.minor = CDNS_UART_MINOR;
1673 cdns_uart_uart_driver.nr = CDNS_UART_NR_PORTS;
1674#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1675 cdns_uart_uart_driver.cons = &cdns_uart_console;
1676#endif
1677
1678 rc = uart_register_driver(&cdns_uart_uart_driver);
1679 if (rc < 0) {
1680 dev_err(&pdev->dev, "Failed to register driver\n");
1681 return rc;
1682 }
1683 }
1684
1685 cdns_uart_data->cdns_uart_driver = &cdns_uart_uart_driver;
1686
1687 match = of_match_node(cdns_uart_of_match, pdev->dev.of_node);
1688 if (match && match->data) {
1689 const struct cdns_platform_data *data = match->data;
1690
1691 cdns_uart_data->quirks = data->quirks;
1692 }
1693
1694 cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "pclk");
1695 if (PTR_ERR(cdns_uart_data->pclk) == -EPROBE_DEFER) {
1696 rc = PTR_ERR(cdns_uart_data->pclk);
1697 goto err_out_unregister_driver;
1698 }
1699
1700 if (IS_ERR(cdns_uart_data->pclk)) {
1701 cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk");
1702 if (IS_ERR(cdns_uart_data->pclk)) {
1703 rc = PTR_ERR(cdns_uart_data->pclk);
1704 goto err_out_unregister_driver;
1705 }
1706 dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n");
1707 }
1708
1709 cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk");
1710 if (PTR_ERR(cdns_uart_data->uartclk) == -EPROBE_DEFER) {
1711 rc = PTR_ERR(cdns_uart_data->uartclk);
1712 goto err_out_unregister_driver;
1713 }
1714
1715 if (IS_ERR(cdns_uart_data->uartclk)) {
1716 cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk");
1717 if (IS_ERR(cdns_uart_data->uartclk)) {
1718 rc = PTR_ERR(cdns_uart_data->uartclk);
1719 goto err_out_unregister_driver;
1720 }
1721 dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
1722 }
1723
1724 rc = clk_prepare_enable(cdns_uart_data->pclk);
1725 if (rc) {
1726 dev_err(&pdev->dev, "Unable to enable pclk clock.\n");
1727 goto err_out_unregister_driver;
1728 }
1729 rc = clk_prepare_enable(cdns_uart_data->uartclk);
1730 if (rc) {
1731 dev_err(&pdev->dev, "Unable to enable device clock.\n");
1732 goto err_out_clk_dis_pclk;
1733 }
1734
1735 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1736 if (!res) {
1737 rc = -ENODEV;
1738 goto err_out_clk_disable;
1739 }
1740
1741 irq = platform_get_irq(pdev, 0);
1742 if (irq < 0) {
1743 rc = irq;
1744 goto err_out_clk_disable;
1745 }
1746
1747#ifdef CONFIG_COMMON_CLK
1748 cdns_uart_data->clk_rate_change_nb.notifier_call =
1749 cdns_uart_clk_notifier_cb;
1750 if (clk_notifier_register(cdns_uart_data->uartclk,
1751 &cdns_uart_data->clk_rate_change_nb))
1752 dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
1753#endif
1754
1755 /* At this point, we've got an empty uart_port struct, initialize it */
1756 spin_lock_init(&port->lock);
1757 port->type = PORT_UNKNOWN;
1758 port->iotype = UPIO_MEM32;
1759 port->flags = UPF_BOOT_AUTOCONF;
1760 port->ops = &cdns_uart_ops;
1761 port->fifosize = CDNS_UART_FIFO_SIZE;
1762 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE);
1763 port->line = id;
1764
1765 /*
1766 * Register the port.
1767 * This function also registers this device with the tty layer
1768 * and triggers invocation of the config_port() entry point.
1769 */
1770 port->mapbase = res->start;
1771 port->irq = irq;
1772 port->dev = &pdev->dev;
1773 port->uartclk = clk_get_rate(cdns_uart_data->uartclk);
1774 port->private_data = cdns_uart_data;
1775 port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
1776 CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
1777 port->rs485_config = cdns_rs485_config;
1778 port->rs485_supported = cdns_rs485_supported;
1779 cdns_uart_data->port = port;
1780 platform_set_drvdata(pdev, port);
1781
1782 rc = uart_get_rs485_mode(port);
1783 if (rc)
1784 goto err_out_clk_notifier;
1785
1786 cdns_uart_data->gpiod_rts = devm_gpiod_get_optional(&pdev->dev, "rts",
1787 GPIOD_OUT_LOW);
1788 if (IS_ERR(cdns_uart_data->gpiod_rts)) {
1789 rc = PTR_ERR(cdns_uart_data->gpiod_rts);
1790 dev_err(port->dev, "xuartps: devm_gpiod_get_optional failed\n");
1791 goto err_out_clk_notifier;
1792 }
1793
1794 pm_runtime_use_autosuspend(&pdev->dev);
1795 pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
1796 pm_runtime_set_active(&pdev->dev);
1797 pm_runtime_enable(&pdev->dev);
1798 device_init_wakeup(port->dev, true);
1799
1800#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1801 /*
1802 * If console hasn't been found yet try to assign this port
1803 * because it is required to be assigned for console setup function.
1804 * If register_console() don't assign value, then console_port pointer
1805 * is cleanup.
1806 */
1807 if (!console_port) {
1808 cdns_uart_console.index = id;
1809 console_port = port;
1810 }
1811#endif
1812 if (cdns_uart_data->port->rs485.flags & SER_RS485_ENABLED)
1813 cdns_rs485_rx_setup(cdns_uart_data);
1814
1815 rc = uart_add_one_port(&cdns_uart_uart_driver, port);
1816 if (rc) {
1817 dev_err(&pdev->dev,
1818 "uart_add_one_port() failed; err=%i\n", rc);
1819 goto err_out_pm_disable;
1820 }
1821
1822#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1823 /* This is not port which is used for console that's why clean it up */
1824 if (console_port == port &&
1825 !console_is_registered(cdns_uart_uart_driver.cons)) {
1826 console_port = NULL;
1827 cdns_uart_console.index = -1;
1828 }
1829#endif
1830
1831 cdns_uart_data->cts_override = of_property_read_bool(pdev->dev.of_node,
1832 "cts-override");
1833
1834 instances++;
1835
1836 return 0;
1837
1838err_out_pm_disable:
1839 pm_runtime_disable(&pdev->dev);
1840 pm_runtime_set_suspended(&pdev->dev);
1841 pm_runtime_dont_use_autosuspend(&pdev->dev);
1842err_out_clk_notifier:
1843#ifdef CONFIG_COMMON_CLK
1844 clk_notifier_unregister(cdns_uart_data->uartclk,
1845 &cdns_uart_data->clk_rate_change_nb);
1846#endif
1847err_out_clk_disable:
1848 clk_disable_unprepare(cdns_uart_data->uartclk);
1849err_out_clk_dis_pclk:
1850 clk_disable_unprepare(cdns_uart_data->pclk);
1851err_out_unregister_driver:
1852 if (!instances)
1853 uart_unregister_driver(cdns_uart_data->cdns_uart_driver);
1854 return rc;
1855}
1856
1857/**
1858 * cdns_uart_remove - called when the platform driver is unregistered
1859 * @pdev: Pointer to the platform device structure
1860 */
1861static void cdns_uart_remove(struct platform_device *pdev)
1862{
1863 struct uart_port *port = platform_get_drvdata(pdev);
1864 struct cdns_uart *cdns_uart_data = port->private_data;
1865
1866 /* Remove the cdns_uart port from the serial core */
1867#ifdef CONFIG_COMMON_CLK
1868 clk_notifier_unregister(cdns_uart_data->uartclk,
1869 &cdns_uart_data->clk_rate_change_nb);
1870#endif
1871 uart_remove_one_port(cdns_uart_data->cdns_uart_driver, port);
1872 port->mapbase = 0;
1873 clk_disable_unprepare(cdns_uart_data->uartclk);
1874 clk_disable_unprepare(cdns_uart_data->pclk);
1875 pm_runtime_disable(&pdev->dev);
1876 pm_runtime_set_suspended(&pdev->dev);
1877 pm_runtime_dont_use_autosuspend(&pdev->dev);
1878 device_init_wakeup(&pdev->dev, false);
1879
1880#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1881 if (console_port == port)
1882 console_port = NULL;
1883#endif
1884
1885 if (!--instances)
1886 uart_unregister_driver(cdns_uart_data->cdns_uart_driver);
1887}
1888
1889static struct platform_driver cdns_uart_platform_driver = {
1890 .probe = cdns_uart_probe,
1891 .remove_new = cdns_uart_remove,
1892 .driver = {
1893 .name = CDNS_UART_NAME,
1894 .of_match_table = cdns_uart_of_match,
1895 .pm = &cdns_uart_dev_pm_ops,
1896 .suppress_bind_attrs = IS_BUILTIN(CONFIG_SERIAL_XILINX_PS_UART),
1897 },
1898};
1899
1900static int __init cdns_uart_init(void)
1901{
1902 /* Register the platform driver */
1903 return platform_driver_register(&cdns_uart_platform_driver);
1904}
1905
1906static void __exit cdns_uart_exit(void)
1907{
1908 /* Unregister the platform driver */
1909 platform_driver_unregister(&cdns_uart_platform_driver);
1910}
1911
1912arch_initcall(cdns_uart_init);
1913module_exit(cdns_uart_exit);
1914
1915MODULE_DESCRIPTION("Driver for Cadence UART");
1916MODULE_AUTHOR("Xilinx Inc.");
1917MODULE_LICENSE("GPL");