Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * TUSB6010 USB 2.0 OTG Dual Role controller
4 *
5 * Copyright (C) 2006 Nokia Corporation
6 * Tony Lindgren <tony@atomide.com>
7 *
8 * Notes:
9 * - Driver assumes that interface to external host (main CPU) is
10 * configured for NOR FLASH interface instead of VLYNQ serial
11 * interface.
12 */
13
14#include <linux/gpio/consumer.h>
15#include <linux/delay.h>
16#include <linux/module.h>
17#include <linux/kernel.h>
18#include <linux/errno.h>
19#include <linux/err.h>
20#include <linux/prefetch.h>
21#include <linux/usb.h>
22#include <linux/irq.h>
23#include <linux/io.h>
24#include <linux/iopoll.h>
25#include <linux/device.h>
26#include <linux/platform_device.h>
27#include <linux/dma-mapping.h>
28#include <linux/usb/usb_phy_generic.h>
29
30#include "musb_core.h"
31
32struct tusb6010_glue {
33 struct device *dev;
34 struct platform_device *musb;
35 struct platform_device *phy;
36 struct gpio_desc *enable;
37 struct gpio_desc *intpin;
38};
39
40static void tusb_musb_set_vbus(struct musb *musb, int is_on);
41
42#define TUSB_REV_MAJOR(reg_val) ((reg_val >> 4) & 0xf)
43#define TUSB_REV_MINOR(reg_val) (reg_val & 0xf)
44
45/*
46 * Checks the revision. We need to use the DMA register as 3.0 does not
47 * have correct versions for TUSB_PRCM_REV or TUSB_INT_CTRL_REV.
48 */
49static u8 tusb_get_revision(struct musb *musb)
50{
51 void __iomem *tbase = musb->ctrl_base;
52 u32 die_id;
53 u8 rev;
54
55 rev = musb_readl(tbase, TUSB_DMA_CTRL_REV) & 0xff;
56 if (TUSB_REV_MAJOR(rev) == 3) {
57 die_id = TUSB_DIDR1_HI_CHIP_REV(musb_readl(tbase,
58 TUSB_DIDR1_HI));
59 if (die_id >= TUSB_DIDR1_HI_REV_31)
60 rev |= 1;
61 }
62
63 return rev;
64}
65
66static void tusb_print_revision(struct musb *musb)
67{
68 void __iomem *tbase = musb->ctrl_base;
69 u8 rev;
70
71 rev = musb->tusb_revision;
72
73 pr_info("tusb: %s%i.%i %s%i.%i %s%i.%i %s%i.%i %s%i %s%i.%i\n",
74 "prcm",
75 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_PRCM_REV)),
76 TUSB_REV_MINOR(musb_readl(tbase, TUSB_PRCM_REV)),
77 "int",
78 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_INT_CTRL_REV)),
79 TUSB_REV_MINOR(musb_readl(tbase, TUSB_INT_CTRL_REV)),
80 "gpio",
81 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_GPIO_REV)),
82 TUSB_REV_MINOR(musb_readl(tbase, TUSB_GPIO_REV)),
83 "dma",
84 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_DMA_CTRL_REV)),
85 TUSB_REV_MINOR(musb_readl(tbase, TUSB_DMA_CTRL_REV)),
86 "dieid",
87 TUSB_DIDR1_HI_CHIP_REV(musb_readl(tbase, TUSB_DIDR1_HI)),
88 "rev",
89 TUSB_REV_MAJOR(rev), TUSB_REV_MINOR(rev));
90}
91
92#define WBUS_QUIRK_MASK (TUSB_PHY_OTG_CTRL_TESTM2 | TUSB_PHY_OTG_CTRL_TESTM1 \
93 | TUSB_PHY_OTG_CTRL_TESTM0)
94
95/*
96 * Workaround for spontaneous WBUS wake-up issue #2 for tusb3.0.
97 * Disables power detection in PHY for the duration of idle.
98 */
99static void tusb_wbus_quirk(struct musb *musb, int enabled)
100{
101 void __iomem *tbase = musb->ctrl_base;
102 static u32 phy_otg_ctrl, phy_otg_ena;
103 u32 tmp;
104
105 if (enabled) {
106 phy_otg_ctrl = musb_readl(tbase, TUSB_PHY_OTG_CTRL);
107 phy_otg_ena = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE);
108 tmp = TUSB_PHY_OTG_CTRL_WRPROTECT
109 | phy_otg_ena | WBUS_QUIRK_MASK;
110 musb_writel(tbase, TUSB_PHY_OTG_CTRL, tmp);
111 tmp = phy_otg_ena & ~WBUS_QUIRK_MASK;
112 tmp |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_TESTM2;
113 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, tmp);
114 dev_dbg(musb->controller, "Enabled tusb wbus quirk ctrl %08x ena %08x\n",
115 musb_readl(tbase, TUSB_PHY_OTG_CTRL),
116 musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE));
117 } else if (musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE)
118 & TUSB_PHY_OTG_CTRL_TESTM2) {
119 tmp = TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ctrl;
120 musb_writel(tbase, TUSB_PHY_OTG_CTRL, tmp);
121 tmp = TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ena;
122 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, tmp);
123 dev_dbg(musb->controller, "Disabled tusb wbus quirk ctrl %08x ena %08x\n",
124 musb_readl(tbase, TUSB_PHY_OTG_CTRL),
125 musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE));
126 phy_otg_ctrl = 0;
127 phy_otg_ena = 0;
128 }
129}
130
131static u32 tusb_fifo_offset(u8 epnum)
132{
133 return 0x200 + (epnum * 0x20);
134}
135
136static u32 tusb_ep_offset(u8 epnum, u16 offset)
137{
138 return 0x10 + offset;
139}
140
141/* TUSB mapping: "flat" plus ep0 special cases */
142static void tusb_ep_select(void __iomem *mbase, u8 epnum)
143{
144 musb_writeb(mbase, MUSB_INDEX, epnum);
145}
146
147/*
148 * TUSB6010 doesn't allow 8-bit access; 16-bit access is the minimum.
149 */
150static u8 tusb_readb(void __iomem *addr, u32 offset)
151{
152 u16 tmp;
153 u8 val;
154
155 tmp = __raw_readw(addr + (offset & ~1));
156 if (offset & 1)
157 val = (tmp >> 8);
158 else
159 val = tmp & 0xff;
160
161 return val;
162}
163
164static void tusb_writeb(void __iomem *addr, u32 offset, u8 data)
165{
166 u16 tmp;
167
168 tmp = __raw_readw(addr + (offset & ~1));
169 if (offset & 1)
170 tmp = (data << 8) | (tmp & 0xff);
171 else
172 tmp = (tmp & 0xff00) | data;
173
174 __raw_writew(tmp, addr + (offset & ~1));
175}
176
177/*
178 * TUSB 6010 may use a parallel bus that doesn't support byte ops;
179 * so both loading and unloading FIFOs need explicit byte counts.
180 */
181
182static inline void
183tusb_fifo_write_unaligned(void __iomem *fifo, const u8 *buf, u16 len)
184{
185 u32 val;
186 int i;
187
188 if (len > 4) {
189 for (i = 0; i < (len >> 2); i++) {
190 memcpy(&val, buf, 4);
191 musb_writel(fifo, 0, val);
192 buf += 4;
193 }
194 len %= 4;
195 }
196 if (len > 0) {
197 /* Write the rest 1 - 3 bytes to FIFO */
198 val = 0;
199 memcpy(&val, buf, len);
200 musb_writel(fifo, 0, val);
201 }
202}
203
204static inline void tusb_fifo_read_unaligned(void __iomem *fifo,
205 void *buf, u16 len)
206{
207 u32 val;
208 int i;
209
210 if (len > 4) {
211 for (i = 0; i < (len >> 2); i++) {
212 val = musb_readl(fifo, 0);
213 memcpy(buf, &val, 4);
214 buf += 4;
215 }
216 len %= 4;
217 }
218 if (len > 0) {
219 /* Read the rest 1 - 3 bytes from FIFO */
220 val = musb_readl(fifo, 0);
221 memcpy(buf, &val, len);
222 }
223}
224
225static void tusb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *buf)
226{
227 struct musb *musb = hw_ep->musb;
228 void __iomem *ep_conf = hw_ep->conf;
229 void __iomem *fifo = hw_ep->fifo;
230 u8 epnum = hw_ep->epnum;
231
232 prefetch(buf);
233
234 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
235 'T', epnum, fifo, len, buf);
236
237 if (epnum)
238 musb_writel(ep_conf, TUSB_EP_TX_OFFSET,
239 TUSB_EP_CONFIG_XFR_SIZE(len));
240 else
241 musb_writel(ep_conf, 0, TUSB_EP0_CONFIG_DIR_TX |
242 TUSB_EP0_CONFIG_XFR_SIZE(len));
243
244 if (likely((0x01 & (unsigned long) buf) == 0)) {
245
246 /* Best case is 32bit-aligned destination address */
247 if ((0x02 & (unsigned long) buf) == 0) {
248 if (len >= 4) {
249 iowrite32_rep(fifo, buf, len >> 2);
250 buf += (len & ~0x03);
251 len &= 0x03;
252 }
253 } else {
254 if (len >= 2) {
255 u32 val;
256 int i;
257
258 /* Cannot use writesw, fifo is 32-bit */
259 for (i = 0; i < (len >> 2); i++) {
260 val = (u32)(*(u16 *)buf);
261 buf += 2;
262 val |= (*(u16 *)buf) << 16;
263 buf += 2;
264 musb_writel(fifo, 0, val);
265 }
266 len &= 0x03;
267 }
268 }
269 }
270
271 if (len > 0)
272 tusb_fifo_write_unaligned(fifo, buf, len);
273}
274
275static void tusb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *buf)
276{
277 struct musb *musb = hw_ep->musb;
278 void __iomem *ep_conf = hw_ep->conf;
279 void __iomem *fifo = hw_ep->fifo;
280 u8 epnum = hw_ep->epnum;
281
282 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
283 'R', epnum, fifo, len, buf);
284
285 if (epnum)
286 musb_writel(ep_conf, TUSB_EP_RX_OFFSET,
287 TUSB_EP_CONFIG_XFR_SIZE(len));
288 else
289 musb_writel(ep_conf, 0, TUSB_EP0_CONFIG_XFR_SIZE(len));
290
291 if (likely((0x01 & (unsigned long) buf) == 0)) {
292
293 /* Best case is 32bit-aligned destination address */
294 if ((0x02 & (unsigned long) buf) == 0) {
295 if (len >= 4) {
296 ioread32_rep(fifo, buf, len >> 2);
297 buf += (len & ~0x03);
298 len &= 0x03;
299 }
300 } else {
301 if (len >= 2) {
302 u32 val;
303 int i;
304
305 /* Cannot use readsw, fifo is 32-bit */
306 for (i = 0; i < (len >> 2); i++) {
307 val = musb_readl(fifo, 0);
308 *(u16 *)buf = (u16)(val & 0xffff);
309 buf += 2;
310 *(u16 *)buf = (u16)(val >> 16);
311 buf += 2;
312 }
313 len &= 0x03;
314 }
315 }
316 }
317
318 if (len > 0)
319 tusb_fifo_read_unaligned(fifo, buf, len);
320}
321
322static struct musb *the_musb;
323
324/* This is used by gadget drivers, and OTG transceiver logic, allowing
325 * at most mA current to be drawn from VBUS during a Default-B session
326 * (that is, while VBUS exceeds 4.4V). In Default-A (including pure host
327 * mode), or low power Default-B sessions, something else supplies power.
328 * Caller must take care of locking.
329 */
330static int tusb_draw_power(struct usb_phy *x, unsigned mA)
331{
332 struct musb *musb = the_musb;
333 void __iomem *tbase = musb->ctrl_base;
334 u32 reg;
335
336 /* tps65030 seems to consume max 100mA, with maybe 60mA available
337 * (measured on one board) for things other than tps and tusb.
338 *
339 * Boards sharing the CPU clock with CLKIN will need to prevent
340 * certain idle sleep states while the USB link is active.
341 *
342 * REVISIT we could use VBUS to supply only _one_ of { 1.5V, 3.3V }.
343 * The actual current usage would be very board-specific. For now,
344 * it's simpler to just use an aggregate (also board-specific).
345 */
346 if (x->otg->default_a || mA < (musb->min_power << 1))
347 mA = 0;
348
349 reg = musb_readl(tbase, TUSB_PRCM_MNGMT);
350 if (mA) {
351 musb->is_bus_powered = 1;
352 reg |= TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN;
353 } else {
354 musb->is_bus_powered = 0;
355 reg &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN);
356 }
357 musb_writel(tbase, TUSB_PRCM_MNGMT, reg);
358
359 dev_dbg(musb->controller, "draw max %d mA VBUS\n", mA);
360 return 0;
361}
362
363/* workaround for issue 13: change clock during chip idle
364 * (to be fixed in rev3 silicon) ... symptoms include disconnect
365 * or looping suspend/resume cycles
366 */
367static void tusb_set_clock_source(struct musb *musb, unsigned mode)
368{
369 void __iomem *tbase = musb->ctrl_base;
370 u32 reg;
371
372 reg = musb_readl(tbase, TUSB_PRCM_CONF);
373 reg &= ~TUSB_PRCM_CONF_SYS_CLKSEL(0x3);
374
375 /* 0 = refclk (clkin, XI)
376 * 1 = PHY 60 MHz (internal PLL)
377 * 2 = not supported
378 * 3 = what?
379 */
380 if (mode > 0)
381 reg |= TUSB_PRCM_CONF_SYS_CLKSEL(mode & 0x3);
382
383 musb_writel(tbase, TUSB_PRCM_CONF, reg);
384
385 /* FIXME tusb6010_platform_retime(mode == 0); */
386}
387
388/*
389 * Idle TUSB6010 until next wake-up event; NOR access always wakes.
390 * Other code ensures that we idle unless we're connected _and_ the
391 * USB link is not suspended ... and tells us the relevant wakeup
392 * events. SW_EN for voltage is handled separately.
393 */
394static void tusb_allow_idle(struct musb *musb, u32 wakeup_enables)
395{
396 void __iomem *tbase = musb->ctrl_base;
397 u32 reg;
398
399 if ((wakeup_enables & TUSB_PRCM_WBUS)
400 && (musb->tusb_revision == TUSB_REV_30))
401 tusb_wbus_quirk(musb, 1);
402
403 tusb_set_clock_source(musb, 0);
404
405 wakeup_enables |= TUSB_PRCM_WNORCS;
406 musb_writel(tbase, TUSB_PRCM_WAKEUP_MASK, ~wakeup_enables);
407
408 /* REVISIT writeup of WID implies that if WID set and ID is grounded,
409 * TUSB_PHY_OTG_CTRL.TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP must be cleared.
410 * Presumably that's mostly to save power, hence WID is immaterial ...
411 */
412
413 reg = musb_readl(tbase, TUSB_PRCM_MNGMT);
414 /* issue 4: when driving vbus, use hipower (vbus_det) comparator */
415 if (is_host_active(musb)) {
416 reg |= TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN;
417 reg &= ~TUSB_PRCM_MNGMT_OTG_SESS_END_EN;
418 } else {
419 reg |= TUSB_PRCM_MNGMT_OTG_SESS_END_EN;
420 reg &= ~TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN;
421 }
422 reg |= TUSB_PRCM_MNGMT_PM_IDLE | TUSB_PRCM_MNGMT_DEV_IDLE;
423 musb_writel(tbase, TUSB_PRCM_MNGMT, reg);
424
425 dev_dbg(musb->controller, "idle, wake on %02x\n", wakeup_enables);
426}
427
428/*
429 * Updates cable VBUS status. Caller must take care of locking.
430 */
431static int tusb_musb_vbus_status(struct musb *musb)
432{
433 void __iomem *tbase = musb->ctrl_base;
434 u32 otg_stat, prcm_mngmt;
435 int ret = 0;
436
437 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
438 prcm_mngmt = musb_readl(tbase, TUSB_PRCM_MNGMT);
439
440 /* Temporarily enable VBUS detection if it was disabled for
441 * suspend mode. Unless it's enabled otg_stat and devctl will
442 * not show correct VBUS state.
443 */
444 if (!(prcm_mngmt & TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN)) {
445 u32 tmp = prcm_mngmt;
446 tmp |= TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN;
447 musb_writel(tbase, TUSB_PRCM_MNGMT, tmp);
448 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
449 musb_writel(tbase, TUSB_PRCM_MNGMT, prcm_mngmt);
450 }
451
452 if (otg_stat & TUSB_DEV_OTG_STAT_VBUS_VALID)
453 ret = 1;
454
455 return ret;
456}
457
458static void musb_do_idle(struct timer_list *t)
459{
460 struct musb *musb = from_timer(musb, t, dev_timer);
461 unsigned long flags;
462
463 spin_lock_irqsave(&musb->lock, flags);
464
465 switch (musb->xceiv->otg->state) {
466 case OTG_STATE_A_WAIT_BCON:
467 if ((musb->a_wait_bcon != 0)
468 && (musb->idle_timeout == 0
469 || time_after(jiffies, musb->idle_timeout))) {
470 dev_dbg(musb->controller, "Nothing connected %s, turning off VBUS\n",
471 usb_otg_state_string(musb->xceiv->otg->state));
472 }
473 fallthrough;
474 case OTG_STATE_A_IDLE:
475 tusb_musb_set_vbus(musb, 0);
476 break;
477 default:
478 break;
479 }
480
481 if (!musb->is_active) {
482 u32 wakeups;
483
484 /* wait until hub_wq handles port change status */
485 if (is_host_active(musb) && (musb->port1_status >> 16))
486 goto done;
487
488 if (!musb->gadget_driver) {
489 wakeups = 0;
490 } else {
491 wakeups = TUSB_PRCM_WHOSTDISCON
492 | TUSB_PRCM_WBUS
493 | TUSB_PRCM_WVBUS;
494 wakeups |= TUSB_PRCM_WID;
495 }
496 tusb_allow_idle(musb, wakeups);
497 }
498done:
499 spin_unlock_irqrestore(&musb->lock, flags);
500}
501
502/*
503 * Maybe put TUSB6010 into idle mode depending on USB link status,
504 * like "disconnected" or "suspended". We'll be woken out of it by
505 * connect, resume, or disconnect.
506 *
507 * Needs to be called as the last function everywhere where there is
508 * register access to TUSB6010 because of NOR flash wake-up.
509 * Caller should own controller spinlock.
510 *
511 * Delay because peripheral enables D+ pullup 3msec after SE0, and
512 * we don't want to treat that full speed J as a wakeup event.
513 * ... peripherals must draw only suspend current after 10 msec.
514 */
515static void tusb_musb_try_idle(struct musb *musb, unsigned long timeout)
516{
517 unsigned long default_timeout = jiffies + msecs_to_jiffies(3);
518 static unsigned long last_timer;
519
520 if (timeout == 0)
521 timeout = default_timeout;
522
523 /* Never idle if active, or when VBUS timeout is not set as host */
524 if (musb->is_active || ((musb->a_wait_bcon == 0)
525 && (musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON))) {
526 dev_dbg(musb->controller, "%s active, deleting timer\n",
527 usb_otg_state_string(musb->xceiv->otg->state));
528 del_timer(&musb->dev_timer);
529 last_timer = jiffies;
530 return;
531 }
532
533 if (time_after(last_timer, timeout)) {
534 if (!timer_pending(&musb->dev_timer))
535 last_timer = timeout;
536 else {
537 dev_dbg(musb->controller, "Longer idle timer already pending, ignoring\n");
538 return;
539 }
540 }
541 last_timer = timeout;
542
543 dev_dbg(musb->controller, "%s inactive, for idle timer for %lu ms\n",
544 usb_otg_state_string(musb->xceiv->otg->state),
545 (unsigned long)jiffies_to_msecs(timeout - jiffies));
546 mod_timer(&musb->dev_timer, timeout);
547}
548
549/* ticks of 60 MHz clock */
550#define DEVCLOCK 60000000
551#define OTG_TIMER_MS(msecs) ((msecs) \
552 ? (TUSB_DEV_OTG_TIMER_VAL((DEVCLOCK/1000)*(msecs)) \
553 | TUSB_DEV_OTG_TIMER_ENABLE) \
554 : 0)
555
556static void tusb_musb_set_vbus(struct musb *musb, int is_on)
557{
558 void __iomem *tbase = musb->ctrl_base;
559 u32 conf, prcm, timer;
560 u8 devctl;
561 struct usb_otg *otg = musb->xceiv->otg;
562
563 /* HDRC controls CPEN, but beware current surges during device
564 * connect. They can trigger transient overcurrent conditions
565 * that must be ignored.
566 */
567
568 prcm = musb_readl(tbase, TUSB_PRCM_MNGMT);
569 conf = musb_readl(tbase, TUSB_DEV_CONF);
570 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
571
572 if (is_on) {
573 timer = OTG_TIMER_MS(OTG_TIME_A_WAIT_VRISE);
574 otg->default_a = 1;
575 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
576 devctl |= MUSB_DEVCTL_SESSION;
577
578 conf |= TUSB_DEV_CONF_USB_HOST_MODE;
579 MUSB_HST_MODE(musb);
580 } else {
581 u32 otg_stat;
582
583 timer = 0;
584
585 /* If ID pin is grounded, we want to be a_idle */
586 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
587 if (!(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS)) {
588 switch (musb->xceiv->otg->state) {
589 case OTG_STATE_A_WAIT_VRISE:
590 case OTG_STATE_A_WAIT_BCON:
591 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
592 break;
593 case OTG_STATE_A_WAIT_VFALL:
594 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
595 break;
596 default:
597 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
598 }
599 musb->is_active = 0;
600 otg->default_a = 1;
601 MUSB_HST_MODE(musb);
602 } else {
603 musb->is_active = 0;
604 otg->default_a = 0;
605 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
606 MUSB_DEV_MODE(musb);
607 }
608
609 devctl &= ~MUSB_DEVCTL_SESSION;
610 conf &= ~TUSB_DEV_CONF_USB_HOST_MODE;
611 }
612 prcm &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN);
613
614 musb_writel(tbase, TUSB_PRCM_MNGMT, prcm);
615 musb_writel(tbase, TUSB_DEV_OTG_TIMER, timer);
616 musb_writel(tbase, TUSB_DEV_CONF, conf);
617 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
618
619 dev_dbg(musb->controller, "VBUS %s, devctl %02x otg %3x conf %08x prcm %08x\n",
620 usb_otg_state_string(musb->xceiv->otg->state),
621 musb_readb(musb->mregs, MUSB_DEVCTL),
622 musb_readl(tbase, TUSB_DEV_OTG_STAT),
623 conf, prcm);
624}
625
626/*
627 * Sets the mode to OTG, peripheral or host by changing the ID detection.
628 * Caller must take care of locking.
629 *
630 * Note that if a mini-A cable is plugged in the ID line will stay down as
631 * the weak ID pull-up is not able to pull the ID up.
632 */
633static int tusb_musb_set_mode(struct musb *musb, u8 musb_mode)
634{
635 void __iomem *tbase = musb->ctrl_base;
636 u32 otg_stat, phy_otg_ctrl, phy_otg_ena, dev_conf;
637
638 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
639 phy_otg_ctrl = musb_readl(tbase, TUSB_PHY_OTG_CTRL);
640 phy_otg_ena = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE);
641 dev_conf = musb_readl(tbase, TUSB_DEV_CONF);
642
643 switch (musb_mode) {
644
645 case MUSB_HOST: /* Disable PHY ID detect, ground ID */
646 phy_otg_ctrl &= ~TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
647 phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
648 dev_conf |= TUSB_DEV_CONF_ID_SEL;
649 dev_conf &= ~TUSB_DEV_CONF_SOFT_ID;
650 break;
651 case MUSB_PERIPHERAL: /* Disable PHY ID detect, keep ID pull-up on */
652 phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
653 phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
654 dev_conf |= (TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID);
655 break;
656 case MUSB_OTG: /* Use PHY ID detection */
657 phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
658 phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
659 dev_conf &= ~(TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID);
660 break;
661
662 default:
663 dev_dbg(musb->controller, "Trying to set mode %i\n", musb_mode);
664 return -EINVAL;
665 }
666
667 musb_writel(tbase, TUSB_PHY_OTG_CTRL,
668 TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ctrl);
669 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE,
670 TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ena);
671 musb_writel(tbase, TUSB_DEV_CONF, dev_conf);
672
673 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
674 if ((musb_mode == MUSB_PERIPHERAL) &&
675 !(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS))
676 INFO("Cannot be peripheral with mini-A cable "
677 "otg_stat: %08x\n", otg_stat);
678
679 return 0;
680}
681
682static inline unsigned long
683tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
684{
685 u32 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
686 unsigned long idle_timeout = 0;
687 struct usb_otg *otg = musb->xceiv->otg;
688
689 /* ID pin */
690 if ((int_src & TUSB_INT_SRC_ID_STATUS_CHNG)) {
691 int default_a;
692
693 default_a = !(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS);
694 dev_dbg(musb->controller, "Default-%c\n", default_a ? 'A' : 'B');
695 otg->default_a = default_a;
696 tusb_musb_set_vbus(musb, default_a);
697
698 /* Don't allow idling immediately */
699 if (default_a)
700 idle_timeout = jiffies + (HZ * 3);
701 }
702
703 /* VBUS state change */
704 if (int_src & TUSB_INT_SRC_VBUS_SENSE_CHNG) {
705
706 /* B-dev state machine: no vbus ~= disconnect */
707 if (!otg->default_a) {
708 /* ? musb_root_disconnect(musb); */
709 musb->port1_status &=
710 ~(USB_PORT_STAT_CONNECTION
711 | USB_PORT_STAT_ENABLE
712 | USB_PORT_STAT_LOW_SPEED
713 | USB_PORT_STAT_HIGH_SPEED
714 | USB_PORT_STAT_TEST
715 );
716
717 if (otg_stat & TUSB_DEV_OTG_STAT_SESS_END) {
718 dev_dbg(musb->controller, "Forcing disconnect (no interrupt)\n");
719 if (musb->xceiv->otg->state != OTG_STATE_B_IDLE) {
720 /* INTR_DISCONNECT can hide... */
721 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
722 musb->int_usb |= MUSB_INTR_DISCONNECT;
723 }
724 musb->is_active = 0;
725 }
726 dev_dbg(musb->controller, "vbus change, %s, otg %03x\n",
727 usb_otg_state_string(musb->xceiv->otg->state), otg_stat);
728 idle_timeout = jiffies + (1 * HZ);
729 schedule_delayed_work(&musb->irq_work, 0);
730
731 } else /* A-dev state machine */ {
732 dev_dbg(musb->controller, "vbus change, %s, otg %03x\n",
733 usb_otg_state_string(musb->xceiv->otg->state), otg_stat);
734
735 switch (musb->xceiv->otg->state) {
736 case OTG_STATE_A_IDLE:
737 dev_dbg(musb->controller, "Got SRP, turning on VBUS\n");
738 musb_platform_set_vbus(musb, 1);
739
740 /* CONNECT can wake if a_wait_bcon is set */
741 if (musb->a_wait_bcon != 0)
742 musb->is_active = 0;
743 else
744 musb->is_active = 1;
745
746 /*
747 * OPT FS A TD.4.6 needs few seconds for
748 * A_WAIT_VRISE
749 */
750 idle_timeout = jiffies + (2 * HZ);
751
752 break;
753 case OTG_STATE_A_WAIT_VRISE:
754 /* ignore; A-session-valid < VBUS_VALID/2,
755 * we monitor this with the timer
756 */
757 break;
758 case OTG_STATE_A_WAIT_VFALL:
759 /* REVISIT this irq triggers during short
760 * spikes caused by enumeration ...
761 */
762 if (musb->vbuserr_retry) {
763 musb->vbuserr_retry--;
764 tusb_musb_set_vbus(musb, 1);
765 } else {
766 musb->vbuserr_retry
767 = VBUSERR_RETRY_COUNT;
768 tusb_musb_set_vbus(musb, 0);
769 }
770 break;
771 default:
772 break;
773 }
774 }
775 }
776
777 /* OTG timer expiration */
778 if (int_src & TUSB_INT_SRC_OTG_TIMEOUT) {
779 u8 devctl;
780
781 dev_dbg(musb->controller, "%s timer, %03x\n",
782 usb_otg_state_string(musb->xceiv->otg->state), otg_stat);
783
784 switch (musb->xceiv->otg->state) {
785 case OTG_STATE_A_WAIT_VRISE:
786 /* VBUS has probably been valid for a while now,
787 * but may well have bounced out of range a bit
788 */
789 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
790 if (otg_stat & TUSB_DEV_OTG_STAT_VBUS_VALID) {
791 if ((devctl & MUSB_DEVCTL_VBUS)
792 != MUSB_DEVCTL_VBUS) {
793 dev_dbg(musb->controller, "devctl %02x\n", devctl);
794 break;
795 }
796 musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
797 musb->is_active = 0;
798 idle_timeout = jiffies
799 + msecs_to_jiffies(musb->a_wait_bcon);
800 } else {
801 /* REVISIT report overcurrent to hub? */
802 ERR("vbus too slow, devctl %02x\n", devctl);
803 tusb_musb_set_vbus(musb, 0);
804 }
805 break;
806 case OTG_STATE_A_WAIT_BCON:
807 if (musb->a_wait_bcon != 0)
808 idle_timeout = jiffies
809 + msecs_to_jiffies(musb->a_wait_bcon);
810 break;
811 case OTG_STATE_A_SUSPEND:
812 break;
813 case OTG_STATE_B_WAIT_ACON:
814 break;
815 default:
816 break;
817 }
818 }
819 schedule_delayed_work(&musb->irq_work, 0);
820
821 return idle_timeout;
822}
823
824static irqreturn_t tusb_musb_interrupt(int irq, void *__hci)
825{
826 struct musb *musb = __hci;
827 void __iomem *tbase = musb->ctrl_base;
828 unsigned long flags, idle_timeout = 0;
829 u32 int_mask, int_src;
830
831 spin_lock_irqsave(&musb->lock, flags);
832
833 /* Mask all interrupts to allow using both edge and level GPIO irq */
834 int_mask = musb_readl(tbase, TUSB_INT_MASK);
835 musb_writel(tbase, TUSB_INT_MASK, ~TUSB_INT_MASK_RESERVED_BITS);
836
837 int_src = musb_readl(tbase, TUSB_INT_SRC) & ~TUSB_INT_SRC_RESERVED_BITS;
838 dev_dbg(musb->controller, "TUSB IRQ %08x\n", int_src);
839
840 musb->int_usb = (u8) int_src;
841
842 /* Acknowledge wake-up source interrupts */
843 if (int_src & TUSB_INT_SRC_DEV_WAKEUP) {
844 u32 reg;
845 u32 i;
846
847 if (musb->tusb_revision == TUSB_REV_30)
848 tusb_wbus_quirk(musb, 0);
849
850 /* there are issues re-locking the PLL on wakeup ... */
851
852 /* work around issue 8 */
853 for (i = 0xf7f7f7; i > 0xf7f7f7 - 1000; i--) {
854 musb_writel(tbase, TUSB_SCRATCH_PAD, 0);
855 musb_writel(tbase, TUSB_SCRATCH_PAD, i);
856 reg = musb_readl(tbase, TUSB_SCRATCH_PAD);
857 if (reg == i)
858 break;
859 dev_dbg(musb->controller, "TUSB NOR not ready\n");
860 }
861
862 /* work around issue 13 (2nd half) */
863 tusb_set_clock_source(musb, 1);
864
865 reg = musb_readl(tbase, TUSB_PRCM_WAKEUP_SOURCE);
866 musb_writel(tbase, TUSB_PRCM_WAKEUP_CLEAR, reg);
867 if (reg & ~TUSB_PRCM_WNORCS) {
868 musb->is_active = 1;
869 schedule_delayed_work(&musb->irq_work, 0);
870 }
871 dev_dbg(musb->controller, "wake %sactive %02x\n",
872 musb->is_active ? "" : "in", reg);
873
874 /* REVISIT host side TUSB_PRCM_WHOSTDISCON, TUSB_PRCM_WBUS */
875 }
876
877 if (int_src & TUSB_INT_SRC_USB_IP_CONN)
878 del_timer(&musb->dev_timer);
879
880 /* OTG state change reports (annoyingly) not issued by Mentor core */
881 if (int_src & (TUSB_INT_SRC_VBUS_SENSE_CHNG
882 | TUSB_INT_SRC_OTG_TIMEOUT
883 | TUSB_INT_SRC_ID_STATUS_CHNG))
884 idle_timeout = tusb_otg_ints(musb, int_src, tbase);
885
886 /*
887 * Just clear the DMA interrupt if it comes as the completion for both
888 * TX and RX is handled by the DMA callback in tusb6010_omap
889 */
890 if ((int_src & TUSB_INT_SRC_TXRX_DMA_DONE)) {
891 u32 dma_src = musb_readl(tbase, TUSB_DMA_INT_SRC);
892
893 dev_dbg(musb->controller, "DMA IRQ %08x\n", dma_src);
894 musb_writel(tbase, TUSB_DMA_INT_CLEAR, dma_src);
895 }
896
897 /* EP interrupts. In OCP mode tusb6010 mirrors the MUSB interrupts */
898 if (int_src & (TUSB_INT_SRC_USB_IP_TX | TUSB_INT_SRC_USB_IP_RX)) {
899 u32 musb_src = musb_readl(tbase, TUSB_USBIP_INT_SRC);
900
901 musb_writel(tbase, TUSB_USBIP_INT_CLEAR, musb_src);
902 musb->int_rx = (((musb_src >> 16) & 0xffff) << 1);
903 musb->int_tx = (musb_src & 0xffff);
904 } else {
905 musb->int_rx = 0;
906 musb->int_tx = 0;
907 }
908
909 if (int_src & (TUSB_INT_SRC_USB_IP_TX | TUSB_INT_SRC_USB_IP_RX | 0xff))
910 musb_interrupt(musb);
911
912 /* Acknowledge TUSB interrupts. Clear only non-reserved bits */
913 musb_writel(tbase, TUSB_INT_SRC_CLEAR,
914 int_src & ~TUSB_INT_MASK_RESERVED_BITS);
915
916 tusb_musb_try_idle(musb, idle_timeout);
917
918 musb_writel(tbase, TUSB_INT_MASK, int_mask);
919 spin_unlock_irqrestore(&musb->lock, flags);
920
921 return IRQ_HANDLED;
922}
923
924static int dma_off;
925
926/*
927 * Enables TUSB6010. Caller must take care of locking.
928 * REVISIT:
929 * - Check what is unnecessary in MGC_HdrcStart()
930 */
931static void tusb_musb_enable(struct musb *musb)
932{
933 void __iomem *tbase = musb->ctrl_base;
934
935 /* Setup TUSB6010 main interrupt mask. Enable all interrupts except SOF.
936 * REVISIT: Enable and deal with TUSB_INT_SRC_USB_IP_SOF */
937 musb_writel(tbase, TUSB_INT_MASK, TUSB_INT_SRC_USB_IP_SOF);
938
939 /* Setup TUSB interrupt, disable DMA and GPIO interrupts */
940 musb_writel(tbase, TUSB_USBIP_INT_MASK, 0);
941 musb_writel(tbase, TUSB_DMA_INT_MASK, 0x7fffffff);
942 musb_writel(tbase, TUSB_GPIO_INT_MASK, 0x1ff);
943
944 /* Clear all subsystem interrups */
945 musb_writel(tbase, TUSB_USBIP_INT_CLEAR, 0x7fffffff);
946 musb_writel(tbase, TUSB_DMA_INT_CLEAR, 0x7fffffff);
947 musb_writel(tbase, TUSB_GPIO_INT_CLEAR, 0x1ff);
948
949 /* Acknowledge pending interrupt(s) */
950 musb_writel(tbase, TUSB_INT_SRC_CLEAR, ~TUSB_INT_MASK_RESERVED_BITS);
951
952 /* Only 0 clock cycles for minimum interrupt de-assertion time and
953 * interrupt polarity active low seems to work reliably here */
954 musb_writel(tbase, TUSB_INT_CTRL_CONF,
955 TUSB_INT_CTRL_CONF_INT_RELCYC(0));
956
957 irq_set_irq_type(musb->nIrq, IRQ_TYPE_LEVEL_LOW);
958
959 /* maybe force into the Default-A OTG state machine */
960 if (!(musb_readl(tbase, TUSB_DEV_OTG_STAT)
961 & TUSB_DEV_OTG_STAT_ID_STATUS))
962 musb_writel(tbase, TUSB_INT_SRC_SET,
963 TUSB_INT_SRC_ID_STATUS_CHNG);
964
965 if (is_dma_capable() && dma_off)
966 printk(KERN_WARNING "%s %s: dma not reactivated\n",
967 __FILE__, __func__);
968 else
969 dma_off = 1;
970}
971
972/*
973 * Disables TUSB6010. Caller must take care of locking.
974 */
975static void tusb_musb_disable(struct musb *musb)
976{
977 void __iomem *tbase = musb->ctrl_base;
978
979 /* FIXME stop DMA, IRQs, timers, ... */
980
981 /* disable all IRQs */
982 musb_writel(tbase, TUSB_INT_MASK, ~TUSB_INT_MASK_RESERVED_BITS);
983 musb_writel(tbase, TUSB_USBIP_INT_MASK, 0x7fffffff);
984 musb_writel(tbase, TUSB_DMA_INT_MASK, 0x7fffffff);
985 musb_writel(tbase, TUSB_GPIO_INT_MASK, 0x1ff);
986
987 del_timer(&musb->dev_timer);
988
989 if (is_dma_capable() && !dma_off) {
990 printk(KERN_WARNING "%s %s: dma still active\n",
991 __FILE__, __func__);
992 dma_off = 1;
993 }
994}
995
996/*
997 * Sets up TUSB6010 CPU interface specific signals and registers
998 * Note: Settings optimized for OMAP24xx
999 */
1000static void tusb_setup_cpu_interface(struct musb *musb)
1001{
1002 void __iomem *tbase = musb->ctrl_base;
1003
1004 /*
1005 * Disable GPIO[5:0] pullups (used as output DMA requests)
1006 * Don't disable GPIO[7:6] as they are needed for wake-up.
1007 */
1008 musb_writel(tbase, TUSB_PULLUP_1_CTRL, 0x0000003F);
1009
1010 /* Disable all pullups on NOR IF, DMAREQ0 and DMAREQ1 */
1011 musb_writel(tbase, TUSB_PULLUP_2_CTRL, 0x01FFFFFF);
1012
1013 /* Turn GPIO[5:0] to DMAREQ[5:0] signals */
1014 musb_writel(tbase, TUSB_GPIO_CONF, TUSB_GPIO_CONF_DMAREQ(0x3f));
1015
1016 /* Burst size 16x16 bits, all six DMA requests enabled, DMA request
1017 * de-assertion time 2 system clocks p 62 */
1018 musb_writel(tbase, TUSB_DMA_REQ_CONF,
1019 TUSB_DMA_REQ_CONF_BURST_SIZE(2) |
1020 TUSB_DMA_REQ_CONF_DMA_REQ_EN(0x3f) |
1021 TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(2));
1022
1023 /* Set 0 wait count for synchronous burst access */
1024 musb_writel(tbase, TUSB_WAIT_COUNT, 1);
1025}
1026
1027static int tusb_musb_start(struct musb *musb)
1028{
1029 struct tusb6010_glue *glue = dev_get_drvdata(musb->controller->parent);
1030 void __iomem *tbase = musb->ctrl_base;
1031 unsigned long flags;
1032 u32 reg;
1033 int ret;
1034
1035 /*
1036 * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
1037 * 1.5 V voltage regulators of PM companion chip. Companion chip will then
1038 * provide then PGOOD signal to TUSB6010 which will release it from reset.
1039 */
1040 gpiod_set_value(glue->enable, 1);
1041
1042 /* Wait for 100ms until TUSB6010 pulls INT pin down */
1043 ret = read_poll_timeout(gpiod_get_value, reg, !reg, 5000, 100000, true,
1044 glue->intpin);
1045 if (ret) {
1046 pr_err("tusb: Powerup response failed\n");
1047 return ret;
1048 }
1049
1050 spin_lock_irqsave(&musb->lock, flags);
1051
1052 if (musb_readl(tbase, TUSB_PROD_TEST_RESET) !=
1053 TUSB_PROD_TEST_RESET_VAL) {
1054 printk(KERN_ERR "tusb: Unable to detect TUSB6010\n");
1055 goto err;
1056 }
1057
1058 musb->tusb_revision = tusb_get_revision(musb);
1059 tusb_print_revision(musb);
1060 if (musb->tusb_revision < 2) {
1061 printk(KERN_ERR "tusb: Unsupported TUSB6010 revision %i\n",
1062 musb->tusb_revision);
1063 goto err;
1064 }
1065
1066 /* The uint bit for "USB non-PDR interrupt enable" has to be 1 when
1067 * NOR FLASH interface is used */
1068 musb_writel(tbase, TUSB_VLYNQ_CTRL, 8);
1069
1070 /* Select PHY free running 60MHz as a system clock */
1071 tusb_set_clock_source(musb, 1);
1072
1073 /* VBus valid timer 1us, disable DFT/Debug and VLYNQ clocks for
1074 * power saving, enable VBus detect and session end comparators,
1075 * enable IDpullup, enable VBus charging */
1076 musb_writel(tbase, TUSB_PRCM_MNGMT,
1077 TUSB_PRCM_MNGMT_VBUS_VALID_TIMER(0xa) |
1078 TUSB_PRCM_MNGMT_VBUS_VALID_FLT_EN |
1079 TUSB_PRCM_MNGMT_OTG_SESS_END_EN |
1080 TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN |
1081 TUSB_PRCM_MNGMT_OTG_ID_PULLUP);
1082 tusb_setup_cpu_interface(musb);
1083
1084 /* simplify: always sense/pullup ID pins, as if in OTG mode */
1085 reg = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE);
1086 reg |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
1087 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, reg);
1088
1089 reg = musb_readl(tbase, TUSB_PHY_OTG_CTRL);
1090 reg |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
1091 musb_writel(tbase, TUSB_PHY_OTG_CTRL, reg);
1092
1093 spin_unlock_irqrestore(&musb->lock, flags);
1094
1095 return 0;
1096
1097err:
1098 spin_unlock_irqrestore(&musb->lock, flags);
1099
1100 gpiod_set_value(glue->enable, 0);
1101 msleep(10);
1102
1103 return -ENODEV;
1104}
1105
1106static int tusb_musb_init(struct musb *musb)
1107{
1108 struct platform_device *pdev;
1109 struct resource *mem;
1110 void __iomem *sync = NULL;
1111 int ret;
1112
1113 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
1114 if (IS_ERR_OR_NULL(musb->xceiv))
1115 return -EPROBE_DEFER;
1116
1117 pdev = to_platform_device(musb->controller);
1118
1119 /* dma address for async dma */
1120 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1121 if (!mem) {
1122 pr_debug("no async dma resource?\n");
1123 ret = -ENODEV;
1124 goto done;
1125 }
1126 musb->async = mem->start;
1127
1128 /* dma address for sync dma */
1129 mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
1130 if (!mem) {
1131 pr_debug("no sync dma resource?\n");
1132 ret = -ENODEV;
1133 goto done;
1134 }
1135 musb->sync = mem->start;
1136
1137 sync = ioremap(mem->start, resource_size(mem));
1138 if (!sync) {
1139 pr_debug("ioremap for sync failed\n");
1140 ret = -ENOMEM;
1141 goto done;
1142 }
1143 musb->sync_va = sync;
1144
1145 /* Offsets from base: VLYNQ at 0x000, MUSB regs at 0x400,
1146 * FIFOs at 0x600, TUSB at 0x800
1147 */
1148 musb->mregs += TUSB_BASE_OFFSET;
1149
1150 ret = tusb_musb_start(musb);
1151 if (ret) {
1152 printk(KERN_ERR "Could not start tusb6010 (%d)\n",
1153 ret);
1154 goto done;
1155 }
1156 musb->isr = tusb_musb_interrupt;
1157
1158 musb->xceiv->set_power = tusb_draw_power;
1159 the_musb = musb;
1160
1161 timer_setup(&musb->dev_timer, musb_do_idle, 0);
1162
1163done:
1164 if (ret < 0) {
1165 if (sync)
1166 iounmap(sync);
1167
1168 usb_put_phy(musb->xceiv);
1169 }
1170 return ret;
1171}
1172
1173static int tusb_musb_exit(struct musb *musb)
1174{
1175 struct tusb6010_glue *glue = dev_get_drvdata(musb->controller->parent);
1176
1177 del_timer_sync(&musb->dev_timer);
1178 the_musb = NULL;
1179
1180 gpiod_set_value(glue->enable, 0);
1181 msleep(10);
1182
1183 iounmap(musb->sync_va);
1184
1185 usb_put_phy(musb->xceiv);
1186 return 0;
1187}
1188
1189static const struct musb_platform_ops tusb_ops = {
1190 .quirks = MUSB_DMA_TUSB_OMAP | MUSB_IN_TUSB |
1191 MUSB_G_NO_SKB_RESERVE,
1192 .init = tusb_musb_init,
1193 .exit = tusb_musb_exit,
1194
1195 .ep_offset = tusb_ep_offset,
1196 .ep_select = tusb_ep_select,
1197 .fifo_offset = tusb_fifo_offset,
1198 .readb = tusb_readb,
1199 .writeb = tusb_writeb,
1200 .read_fifo = tusb_read_fifo,
1201 .write_fifo = tusb_write_fifo,
1202#ifdef CONFIG_USB_TUSB_OMAP_DMA
1203 .dma_init = tusb_dma_controller_create,
1204 .dma_exit = tusb_dma_controller_destroy,
1205#endif
1206 .enable = tusb_musb_enable,
1207 .disable = tusb_musb_disable,
1208
1209 .set_mode = tusb_musb_set_mode,
1210 .try_idle = tusb_musb_try_idle,
1211
1212 .vbus_status = tusb_musb_vbus_status,
1213 .set_vbus = tusb_musb_set_vbus,
1214};
1215
1216static const struct platform_device_info tusb_dev_info = {
1217 .name = "musb-hdrc",
1218 .id = PLATFORM_DEVID_AUTO,
1219 .dma_mask = DMA_BIT_MASK(32),
1220};
1221
1222static int tusb_probe(struct platform_device *pdev)
1223{
1224 struct resource musb_resources[3];
1225 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
1226 struct platform_device *musb;
1227 struct tusb6010_glue *glue;
1228 struct platform_device_info pinfo;
1229 int ret;
1230
1231 glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
1232 if (!glue)
1233 return -ENOMEM;
1234
1235 glue->dev = &pdev->dev;
1236
1237 glue->enable = devm_gpiod_get(glue->dev, "enable", GPIOD_OUT_LOW);
1238 if (IS_ERR(glue->enable))
1239 return dev_err_probe(glue->dev, PTR_ERR(glue->enable),
1240 "could not obtain power on/off GPIO\n");
1241 glue->intpin = devm_gpiod_get(glue->dev, "int", GPIOD_IN);
1242 if (IS_ERR(glue->intpin))
1243 return dev_err_probe(glue->dev, PTR_ERR(glue->intpin),
1244 "could not obtain INT GPIO\n");
1245
1246 pdata->platform_ops = &tusb_ops;
1247
1248 usb_phy_generic_register();
1249 platform_set_drvdata(pdev, glue);
1250
1251 memset(musb_resources, 0x00, sizeof(*musb_resources) *
1252 ARRAY_SIZE(musb_resources));
1253
1254 musb_resources[0].name = pdev->resource[0].name;
1255 musb_resources[0].start = pdev->resource[0].start;
1256 musb_resources[0].end = pdev->resource[0].end;
1257 musb_resources[0].flags = pdev->resource[0].flags;
1258
1259 musb_resources[1].name = pdev->resource[1].name;
1260 musb_resources[1].start = pdev->resource[1].start;
1261 musb_resources[1].end = pdev->resource[1].end;
1262 musb_resources[1].flags = pdev->resource[1].flags;
1263
1264 musb_resources[2] = DEFINE_RES_IRQ_NAMED(gpiod_to_irq(glue->intpin), "mc");
1265
1266 pinfo = tusb_dev_info;
1267 pinfo.parent = &pdev->dev;
1268 pinfo.res = musb_resources;
1269 pinfo.num_res = ARRAY_SIZE(musb_resources);
1270 pinfo.data = pdata;
1271 pinfo.size_data = sizeof(*pdata);
1272
1273 glue->musb = musb = platform_device_register_full(&pinfo);
1274 if (IS_ERR(musb)) {
1275 ret = PTR_ERR(musb);
1276 dev_err(&pdev->dev, "failed to register musb device: %d\n", ret);
1277 return ret;
1278 }
1279
1280 return 0;
1281}
1282
1283static void tusb_remove(struct platform_device *pdev)
1284{
1285 struct tusb6010_glue *glue = platform_get_drvdata(pdev);
1286
1287 platform_device_unregister(glue->musb);
1288 usb_phy_generic_unregister(glue->phy);
1289}
1290
1291static struct platform_driver tusb_driver = {
1292 .probe = tusb_probe,
1293 .remove_new = tusb_remove,
1294 .driver = {
1295 .name = "musb-tusb",
1296 },
1297};
1298
1299MODULE_DESCRIPTION("TUSB6010 MUSB Glue Layer");
1300MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
1301MODULE_LICENSE("GPL v2");
1302module_platform_driver(tusb_driver);
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * TUSB6010 USB 2.0 OTG Dual Role controller
4 *
5 * Copyright (C) 2006 Nokia Corporation
6 * Tony Lindgren <tony@atomide.com>
7 *
8 * Notes:
9 * - Driver assumes that interface to external host (main CPU) is
10 * configured for NOR FLASH interface instead of VLYNQ serial
11 * interface.
12 */
13
14#include <linux/module.h>
15#include <linux/kernel.h>
16#include <linux/errno.h>
17#include <linux/err.h>
18#include <linux/prefetch.h>
19#include <linux/usb.h>
20#include <linux/irq.h>
21#include <linux/io.h>
22#include <linux/device.h>
23#include <linux/platform_device.h>
24#include <linux/dma-mapping.h>
25#include <linux/usb/usb_phy_generic.h>
26
27#include "musb_core.h"
28
29struct tusb6010_glue {
30 struct device *dev;
31 struct platform_device *musb;
32 struct platform_device *phy;
33};
34
35static void tusb_musb_set_vbus(struct musb *musb, int is_on);
36
37#define TUSB_REV_MAJOR(reg_val) ((reg_val >> 4) & 0xf)
38#define TUSB_REV_MINOR(reg_val) (reg_val & 0xf)
39
40/*
41 * Checks the revision. We need to use the DMA register as 3.0 does not
42 * have correct versions for TUSB_PRCM_REV or TUSB_INT_CTRL_REV.
43 */
44static u8 tusb_get_revision(struct musb *musb)
45{
46 void __iomem *tbase = musb->ctrl_base;
47 u32 die_id;
48 u8 rev;
49
50 rev = musb_readl(tbase, TUSB_DMA_CTRL_REV) & 0xff;
51 if (TUSB_REV_MAJOR(rev) == 3) {
52 die_id = TUSB_DIDR1_HI_CHIP_REV(musb_readl(tbase,
53 TUSB_DIDR1_HI));
54 if (die_id >= TUSB_DIDR1_HI_REV_31)
55 rev |= 1;
56 }
57
58 return rev;
59}
60
61static void tusb_print_revision(struct musb *musb)
62{
63 void __iomem *tbase = musb->ctrl_base;
64 u8 rev;
65
66 rev = musb->tusb_revision;
67
68 pr_info("tusb: %s%i.%i %s%i.%i %s%i.%i %s%i.%i %s%i %s%i.%i\n",
69 "prcm",
70 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_PRCM_REV)),
71 TUSB_REV_MINOR(musb_readl(tbase, TUSB_PRCM_REV)),
72 "int",
73 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_INT_CTRL_REV)),
74 TUSB_REV_MINOR(musb_readl(tbase, TUSB_INT_CTRL_REV)),
75 "gpio",
76 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_GPIO_REV)),
77 TUSB_REV_MINOR(musb_readl(tbase, TUSB_GPIO_REV)),
78 "dma",
79 TUSB_REV_MAJOR(musb_readl(tbase, TUSB_DMA_CTRL_REV)),
80 TUSB_REV_MINOR(musb_readl(tbase, TUSB_DMA_CTRL_REV)),
81 "dieid",
82 TUSB_DIDR1_HI_CHIP_REV(musb_readl(tbase, TUSB_DIDR1_HI)),
83 "rev",
84 TUSB_REV_MAJOR(rev), TUSB_REV_MINOR(rev));
85}
86
87#define WBUS_QUIRK_MASK (TUSB_PHY_OTG_CTRL_TESTM2 | TUSB_PHY_OTG_CTRL_TESTM1 \
88 | TUSB_PHY_OTG_CTRL_TESTM0)
89
90/*
91 * Workaround for spontaneous WBUS wake-up issue #2 for tusb3.0.
92 * Disables power detection in PHY for the duration of idle.
93 */
94static void tusb_wbus_quirk(struct musb *musb, int enabled)
95{
96 void __iomem *tbase = musb->ctrl_base;
97 static u32 phy_otg_ctrl, phy_otg_ena;
98 u32 tmp;
99
100 if (enabled) {
101 phy_otg_ctrl = musb_readl(tbase, TUSB_PHY_OTG_CTRL);
102 phy_otg_ena = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE);
103 tmp = TUSB_PHY_OTG_CTRL_WRPROTECT
104 | phy_otg_ena | WBUS_QUIRK_MASK;
105 musb_writel(tbase, TUSB_PHY_OTG_CTRL, tmp);
106 tmp = phy_otg_ena & ~WBUS_QUIRK_MASK;
107 tmp |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_TESTM2;
108 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, tmp);
109 dev_dbg(musb->controller, "Enabled tusb wbus quirk ctrl %08x ena %08x\n",
110 musb_readl(tbase, TUSB_PHY_OTG_CTRL),
111 musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE));
112 } else if (musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE)
113 & TUSB_PHY_OTG_CTRL_TESTM2) {
114 tmp = TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ctrl;
115 musb_writel(tbase, TUSB_PHY_OTG_CTRL, tmp);
116 tmp = TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ena;
117 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, tmp);
118 dev_dbg(musb->controller, "Disabled tusb wbus quirk ctrl %08x ena %08x\n",
119 musb_readl(tbase, TUSB_PHY_OTG_CTRL),
120 musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE));
121 phy_otg_ctrl = 0;
122 phy_otg_ena = 0;
123 }
124}
125
126static u32 tusb_fifo_offset(u8 epnum)
127{
128 return 0x200 + (epnum * 0x20);
129}
130
131static u32 tusb_ep_offset(u8 epnum, u16 offset)
132{
133 return 0x10 + offset;
134}
135
136/* TUSB mapping: "flat" plus ep0 special cases */
137static void tusb_ep_select(void __iomem *mbase, u8 epnum)
138{
139 musb_writeb(mbase, MUSB_INDEX, epnum);
140}
141
142/*
143 * TUSB6010 doesn't allow 8-bit access; 16-bit access is the minimum.
144 */
145static u8 tusb_readb(void __iomem *addr, u32 offset)
146{
147 u16 tmp;
148 u8 val;
149
150 tmp = __raw_readw(addr + (offset & ~1));
151 if (offset & 1)
152 val = (tmp >> 8);
153 else
154 val = tmp & 0xff;
155
156 return val;
157}
158
159static void tusb_writeb(void __iomem *addr, u32 offset, u8 data)
160{
161 u16 tmp;
162
163 tmp = __raw_readw(addr + (offset & ~1));
164 if (offset & 1)
165 tmp = (data << 8) | (tmp & 0xff);
166 else
167 tmp = (tmp & 0xff00) | data;
168
169 __raw_writew(tmp, addr + (offset & ~1));
170}
171
172/*
173 * TUSB 6010 may use a parallel bus that doesn't support byte ops;
174 * so both loading and unloading FIFOs need explicit byte counts.
175 */
176
177static inline void
178tusb_fifo_write_unaligned(void __iomem *fifo, const u8 *buf, u16 len)
179{
180 u32 val;
181 int i;
182
183 if (len > 4) {
184 for (i = 0; i < (len >> 2); i++) {
185 memcpy(&val, buf, 4);
186 musb_writel(fifo, 0, val);
187 buf += 4;
188 }
189 len %= 4;
190 }
191 if (len > 0) {
192 /* Write the rest 1 - 3 bytes to FIFO */
193 val = 0;
194 memcpy(&val, buf, len);
195 musb_writel(fifo, 0, val);
196 }
197}
198
199static inline void tusb_fifo_read_unaligned(void __iomem *fifo,
200 void *buf, u16 len)
201{
202 u32 val;
203 int i;
204
205 if (len > 4) {
206 for (i = 0; i < (len >> 2); i++) {
207 val = musb_readl(fifo, 0);
208 memcpy(buf, &val, 4);
209 buf += 4;
210 }
211 len %= 4;
212 }
213 if (len > 0) {
214 /* Read the rest 1 - 3 bytes from FIFO */
215 val = musb_readl(fifo, 0);
216 memcpy(buf, &val, len);
217 }
218}
219
220static void tusb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *buf)
221{
222 struct musb *musb = hw_ep->musb;
223 void __iomem *ep_conf = hw_ep->conf;
224 void __iomem *fifo = hw_ep->fifo;
225 u8 epnum = hw_ep->epnum;
226
227 prefetch(buf);
228
229 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
230 'T', epnum, fifo, len, buf);
231
232 if (epnum)
233 musb_writel(ep_conf, TUSB_EP_TX_OFFSET,
234 TUSB_EP_CONFIG_XFR_SIZE(len));
235 else
236 musb_writel(ep_conf, 0, TUSB_EP0_CONFIG_DIR_TX |
237 TUSB_EP0_CONFIG_XFR_SIZE(len));
238
239 if (likely((0x01 & (unsigned long) buf) == 0)) {
240
241 /* Best case is 32bit-aligned destination address */
242 if ((0x02 & (unsigned long) buf) == 0) {
243 if (len >= 4) {
244 iowrite32_rep(fifo, buf, len >> 2);
245 buf += (len & ~0x03);
246 len &= 0x03;
247 }
248 } else {
249 if (len >= 2) {
250 u32 val;
251 int i;
252
253 /* Cannot use writesw, fifo is 32-bit */
254 for (i = 0; i < (len >> 2); i++) {
255 val = (u32)(*(u16 *)buf);
256 buf += 2;
257 val |= (*(u16 *)buf) << 16;
258 buf += 2;
259 musb_writel(fifo, 0, val);
260 }
261 len &= 0x03;
262 }
263 }
264 }
265
266 if (len > 0)
267 tusb_fifo_write_unaligned(fifo, buf, len);
268}
269
270static void tusb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *buf)
271{
272 struct musb *musb = hw_ep->musb;
273 void __iomem *ep_conf = hw_ep->conf;
274 void __iomem *fifo = hw_ep->fifo;
275 u8 epnum = hw_ep->epnum;
276
277 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
278 'R', epnum, fifo, len, buf);
279
280 if (epnum)
281 musb_writel(ep_conf, TUSB_EP_RX_OFFSET,
282 TUSB_EP_CONFIG_XFR_SIZE(len));
283 else
284 musb_writel(ep_conf, 0, TUSB_EP0_CONFIG_XFR_SIZE(len));
285
286 if (likely((0x01 & (unsigned long) buf) == 0)) {
287
288 /* Best case is 32bit-aligned destination address */
289 if ((0x02 & (unsigned long) buf) == 0) {
290 if (len >= 4) {
291 ioread32_rep(fifo, buf, len >> 2);
292 buf += (len & ~0x03);
293 len &= 0x03;
294 }
295 } else {
296 if (len >= 2) {
297 u32 val;
298 int i;
299
300 /* Cannot use readsw, fifo is 32-bit */
301 for (i = 0; i < (len >> 2); i++) {
302 val = musb_readl(fifo, 0);
303 *(u16 *)buf = (u16)(val & 0xffff);
304 buf += 2;
305 *(u16 *)buf = (u16)(val >> 16);
306 buf += 2;
307 }
308 len &= 0x03;
309 }
310 }
311 }
312
313 if (len > 0)
314 tusb_fifo_read_unaligned(fifo, buf, len);
315}
316
317static struct musb *the_musb;
318
319/* This is used by gadget drivers, and OTG transceiver logic, allowing
320 * at most mA current to be drawn from VBUS during a Default-B session
321 * (that is, while VBUS exceeds 4.4V). In Default-A (including pure host
322 * mode), or low power Default-B sessions, something else supplies power.
323 * Caller must take care of locking.
324 */
325static int tusb_draw_power(struct usb_phy *x, unsigned mA)
326{
327 struct musb *musb = the_musb;
328 void __iomem *tbase = musb->ctrl_base;
329 u32 reg;
330
331 /* tps65030 seems to consume max 100mA, with maybe 60mA available
332 * (measured on one board) for things other than tps and tusb.
333 *
334 * Boards sharing the CPU clock with CLKIN will need to prevent
335 * certain idle sleep states while the USB link is active.
336 *
337 * REVISIT we could use VBUS to supply only _one_ of { 1.5V, 3.3V }.
338 * The actual current usage would be very board-specific. For now,
339 * it's simpler to just use an aggregate (also board-specific).
340 */
341 if (x->otg->default_a || mA < (musb->min_power << 1))
342 mA = 0;
343
344 reg = musb_readl(tbase, TUSB_PRCM_MNGMT);
345 if (mA) {
346 musb->is_bus_powered = 1;
347 reg |= TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN;
348 } else {
349 musb->is_bus_powered = 0;
350 reg &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN);
351 }
352 musb_writel(tbase, TUSB_PRCM_MNGMT, reg);
353
354 dev_dbg(musb->controller, "draw max %d mA VBUS\n", mA);
355 return 0;
356}
357
358/* workaround for issue 13: change clock during chip idle
359 * (to be fixed in rev3 silicon) ... symptoms include disconnect
360 * or looping suspend/resume cycles
361 */
362static void tusb_set_clock_source(struct musb *musb, unsigned mode)
363{
364 void __iomem *tbase = musb->ctrl_base;
365 u32 reg;
366
367 reg = musb_readl(tbase, TUSB_PRCM_CONF);
368 reg &= ~TUSB_PRCM_CONF_SYS_CLKSEL(0x3);
369
370 /* 0 = refclk (clkin, XI)
371 * 1 = PHY 60 MHz (internal PLL)
372 * 2 = not supported
373 * 3 = what?
374 */
375 if (mode > 0)
376 reg |= TUSB_PRCM_CONF_SYS_CLKSEL(mode & 0x3);
377
378 musb_writel(tbase, TUSB_PRCM_CONF, reg);
379
380 /* FIXME tusb6010_platform_retime(mode == 0); */
381}
382
383/*
384 * Idle TUSB6010 until next wake-up event; NOR access always wakes.
385 * Other code ensures that we idle unless we're connected _and_ the
386 * USB link is not suspended ... and tells us the relevant wakeup
387 * events. SW_EN for voltage is handled separately.
388 */
389static void tusb_allow_idle(struct musb *musb, u32 wakeup_enables)
390{
391 void __iomem *tbase = musb->ctrl_base;
392 u32 reg;
393
394 if ((wakeup_enables & TUSB_PRCM_WBUS)
395 && (musb->tusb_revision == TUSB_REV_30))
396 tusb_wbus_quirk(musb, 1);
397
398 tusb_set_clock_source(musb, 0);
399
400 wakeup_enables |= TUSB_PRCM_WNORCS;
401 musb_writel(tbase, TUSB_PRCM_WAKEUP_MASK, ~wakeup_enables);
402
403 /* REVISIT writeup of WID implies that if WID set and ID is grounded,
404 * TUSB_PHY_OTG_CTRL.TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP must be cleared.
405 * Presumably that's mostly to save power, hence WID is immaterial ...
406 */
407
408 reg = musb_readl(tbase, TUSB_PRCM_MNGMT);
409 /* issue 4: when driving vbus, use hipower (vbus_det) comparator */
410 if (is_host_active(musb)) {
411 reg |= TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN;
412 reg &= ~TUSB_PRCM_MNGMT_OTG_SESS_END_EN;
413 } else {
414 reg |= TUSB_PRCM_MNGMT_OTG_SESS_END_EN;
415 reg &= ~TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN;
416 }
417 reg |= TUSB_PRCM_MNGMT_PM_IDLE | TUSB_PRCM_MNGMT_DEV_IDLE;
418 musb_writel(tbase, TUSB_PRCM_MNGMT, reg);
419
420 dev_dbg(musb->controller, "idle, wake on %02x\n", wakeup_enables);
421}
422
423/*
424 * Updates cable VBUS status. Caller must take care of locking.
425 */
426static int tusb_musb_vbus_status(struct musb *musb)
427{
428 void __iomem *tbase = musb->ctrl_base;
429 u32 otg_stat, prcm_mngmt;
430 int ret = 0;
431
432 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
433 prcm_mngmt = musb_readl(tbase, TUSB_PRCM_MNGMT);
434
435 /* Temporarily enable VBUS detection if it was disabled for
436 * suspend mode. Unless it's enabled otg_stat and devctl will
437 * not show correct VBUS state.
438 */
439 if (!(prcm_mngmt & TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN)) {
440 u32 tmp = prcm_mngmt;
441 tmp |= TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN;
442 musb_writel(tbase, TUSB_PRCM_MNGMT, tmp);
443 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
444 musb_writel(tbase, TUSB_PRCM_MNGMT, prcm_mngmt);
445 }
446
447 if (otg_stat & TUSB_DEV_OTG_STAT_VBUS_VALID)
448 ret = 1;
449
450 return ret;
451}
452
453static void musb_do_idle(struct timer_list *t)
454{
455 struct musb *musb = from_timer(musb, t, dev_timer);
456 unsigned long flags;
457
458 spin_lock_irqsave(&musb->lock, flags);
459
460 switch (musb->xceiv->otg->state) {
461 case OTG_STATE_A_WAIT_BCON:
462 if ((musb->a_wait_bcon != 0)
463 && (musb->idle_timeout == 0
464 || time_after(jiffies, musb->idle_timeout))) {
465 dev_dbg(musb->controller, "Nothing connected %s, turning off VBUS\n",
466 usb_otg_state_string(musb->xceiv->otg->state));
467 }
468 fallthrough;
469 case OTG_STATE_A_IDLE:
470 tusb_musb_set_vbus(musb, 0);
471 break;
472 default:
473 break;
474 }
475
476 if (!musb->is_active) {
477 u32 wakeups;
478
479 /* wait until hub_wq handles port change status */
480 if (is_host_active(musb) && (musb->port1_status >> 16))
481 goto done;
482
483 if (!musb->gadget_driver) {
484 wakeups = 0;
485 } else {
486 wakeups = TUSB_PRCM_WHOSTDISCON
487 | TUSB_PRCM_WBUS
488 | TUSB_PRCM_WVBUS;
489 wakeups |= TUSB_PRCM_WID;
490 }
491 tusb_allow_idle(musb, wakeups);
492 }
493done:
494 spin_unlock_irqrestore(&musb->lock, flags);
495}
496
497/*
498 * Maybe put TUSB6010 into idle mode depending on USB link status,
499 * like "disconnected" or "suspended". We'll be woken out of it by
500 * connect, resume, or disconnect.
501 *
502 * Needs to be called as the last function everywhere where there is
503 * register access to TUSB6010 because of NOR flash wake-up.
504 * Caller should own controller spinlock.
505 *
506 * Delay because peripheral enables D+ pullup 3msec after SE0, and
507 * we don't want to treat that full speed J as a wakeup event.
508 * ... peripherals must draw only suspend current after 10 msec.
509 */
510static void tusb_musb_try_idle(struct musb *musb, unsigned long timeout)
511{
512 unsigned long default_timeout = jiffies + msecs_to_jiffies(3);
513 static unsigned long last_timer;
514
515 if (timeout == 0)
516 timeout = default_timeout;
517
518 /* Never idle if active, or when VBUS timeout is not set as host */
519 if (musb->is_active || ((musb->a_wait_bcon == 0)
520 && (musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON))) {
521 dev_dbg(musb->controller, "%s active, deleting timer\n",
522 usb_otg_state_string(musb->xceiv->otg->state));
523 del_timer(&musb->dev_timer);
524 last_timer = jiffies;
525 return;
526 }
527
528 if (time_after(last_timer, timeout)) {
529 if (!timer_pending(&musb->dev_timer))
530 last_timer = timeout;
531 else {
532 dev_dbg(musb->controller, "Longer idle timer already pending, ignoring\n");
533 return;
534 }
535 }
536 last_timer = timeout;
537
538 dev_dbg(musb->controller, "%s inactive, for idle timer for %lu ms\n",
539 usb_otg_state_string(musb->xceiv->otg->state),
540 (unsigned long)jiffies_to_msecs(timeout - jiffies));
541 mod_timer(&musb->dev_timer, timeout);
542}
543
544/* ticks of 60 MHz clock */
545#define DEVCLOCK 60000000
546#define OTG_TIMER_MS(msecs) ((msecs) \
547 ? (TUSB_DEV_OTG_TIMER_VAL((DEVCLOCK/1000)*(msecs)) \
548 | TUSB_DEV_OTG_TIMER_ENABLE) \
549 : 0)
550
551static void tusb_musb_set_vbus(struct musb *musb, int is_on)
552{
553 void __iomem *tbase = musb->ctrl_base;
554 u32 conf, prcm, timer;
555 u8 devctl;
556 struct usb_otg *otg = musb->xceiv->otg;
557
558 /* HDRC controls CPEN, but beware current surges during device
559 * connect. They can trigger transient overcurrent conditions
560 * that must be ignored.
561 */
562
563 prcm = musb_readl(tbase, TUSB_PRCM_MNGMT);
564 conf = musb_readl(tbase, TUSB_DEV_CONF);
565 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
566
567 if (is_on) {
568 timer = OTG_TIMER_MS(OTG_TIME_A_WAIT_VRISE);
569 otg->default_a = 1;
570 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
571 devctl |= MUSB_DEVCTL_SESSION;
572
573 conf |= TUSB_DEV_CONF_USB_HOST_MODE;
574 MUSB_HST_MODE(musb);
575 } else {
576 u32 otg_stat;
577
578 timer = 0;
579
580 /* If ID pin is grounded, we want to be a_idle */
581 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
582 if (!(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS)) {
583 switch (musb->xceiv->otg->state) {
584 case OTG_STATE_A_WAIT_VRISE:
585 case OTG_STATE_A_WAIT_BCON:
586 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
587 break;
588 case OTG_STATE_A_WAIT_VFALL:
589 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
590 break;
591 default:
592 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
593 }
594 musb->is_active = 0;
595 otg->default_a = 1;
596 MUSB_HST_MODE(musb);
597 } else {
598 musb->is_active = 0;
599 otg->default_a = 0;
600 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
601 MUSB_DEV_MODE(musb);
602 }
603
604 devctl &= ~MUSB_DEVCTL_SESSION;
605 conf &= ~TUSB_DEV_CONF_USB_HOST_MODE;
606 }
607 prcm &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN);
608
609 musb_writel(tbase, TUSB_PRCM_MNGMT, prcm);
610 musb_writel(tbase, TUSB_DEV_OTG_TIMER, timer);
611 musb_writel(tbase, TUSB_DEV_CONF, conf);
612 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
613
614 dev_dbg(musb->controller, "VBUS %s, devctl %02x otg %3x conf %08x prcm %08x\n",
615 usb_otg_state_string(musb->xceiv->otg->state),
616 musb_readb(musb->mregs, MUSB_DEVCTL),
617 musb_readl(tbase, TUSB_DEV_OTG_STAT),
618 conf, prcm);
619}
620
621/*
622 * Sets the mode to OTG, peripheral or host by changing the ID detection.
623 * Caller must take care of locking.
624 *
625 * Note that if a mini-A cable is plugged in the ID line will stay down as
626 * the weak ID pull-up is not able to pull the ID up.
627 */
628static int tusb_musb_set_mode(struct musb *musb, u8 musb_mode)
629{
630 void __iomem *tbase = musb->ctrl_base;
631 u32 otg_stat, phy_otg_ctrl, phy_otg_ena, dev_conf;
632
633 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
634 phy_otg_ctrl = musb_readl(tbase, TUSB_PHY_OTG_CTRL);
635 phy_otg_ena = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE);
636 dev_conf = musb_readl(tbase, TUSB_DEV_CONF);
637
638 switch (musb_mode) {
639
640 case MUSB_HOST: /* Disable PHY ID detect, ground ID */
641 phy_otg_ctrl &= ~TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
642 phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
643 dev_conf |= TUSB_DEV_CONF_ID_SEL;
644 dev_conf &= ~TUSB_DEV_CONF_SOFT_ID;
645 break;
646 case MUSB_PERIPHERAL: /* Disable PHY ID detect, keep ID pull-up on */
647 phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
648 phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
649 dev_conf |= (TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID);
650 break;
651 case MUSB_OTG: /* Use PHY ID detection */
652 phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
653 phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
654 dev_conf &= ~(TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID);
655 break;
656
657 default:
658 dev_dbg(musb->controller, "Trying to set mode %i\n", musb_mode);
659 return -EINVAL;
660 }
661
662 musb_writel(tbase, TUSB_PHY_OTG_CTRL,
663 TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ctrl);
664 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE,
665 TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ena);
666 musb_writel(tbase, TUSB_DEV_CONF, dev_conf);
667
668 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
669 if ((musb_mode == MUSB_PERIPHERAL) &&
670 !(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS))
671 INFO("Cannot be peripheral with mini-A cable "
672 "otg_stat: %08x\n", otg_stat);
673
674 return 0;
675}
676
677static inline unsigned long
678tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
679{
680 u32 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
681 unsigned long idle_timeout = 0;
682 struct usb_otg *otg = musb->xceiv->otg;
683
684 /* ID pin */
685 if ((int_src & TUSB_INT_SRC_ID_STATUS_CHNG)) {
686 int default_a;
687
688 default_a = !(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS);
689 dev_dbg(musb->controller, "Default-%c\n", default_a ? 'A' : 'B');
690 otg->default_a = default_a;
691 tusb_musb_set_vbus(musb, default_a);
692
693 /* Don't allow idling immediately */
694 if (default_a)
695 idle_timeout = jiffies + (HZ * 3);
696 }
697
698 /* VBUS state change */
699 if (int_src & TUSB_INT_SRC_VBUS_SENSE_CHNG) {
700
701 /* B-dev state machine: no vbus ~= disconnect */
702 if (!otg->default_a) {
703 /* ? musb_root_disconnect(musb); */
704 musb->port1_status &=
705 ~(USB_PORT_STAT_CONNECTION
706 | USB_PORT_STAT_ENABLE
707 | USB_PORT_STAT_LOW_SPEED
708 | USB_PORT_STAT_HIGH_SPEED
709 | USB_PORT_STAT_TEST
710 );
711
712 if (otg_stat & TUSB_DEV_OTG_STAT_SESS_END) {
713 dev_dbg(musb->controller, "Forcing disconnect (no interrupt)\n");
714 if (musb->xceiv->otg->state != OTG_STATE_B_IDLE) {
715 /* INTR_DISCONNECT can hide... */
716 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
717 musb->int_usb |= MUSB_INTR_DISCONNECT;
718 }
719 musb->is_active = 0;
720 }
721 dev_dbg(musb->controller, "vbus change, %s, otg %03x\n",
722 usb_otg_state_string(musb->xceiv->otg->state), otg_stat);
723 idle_timeout = jiffies + (1 * HZ);
724 schedule_delayed_work(&musb->irq_work, 0);
725
726 } else /* A-dev state machine */ {
727 dev_dbg(musb->controller, "vbus change, %s, otg %03x\n",
728 usb_otg_state_string(musb->xceiv->otg->state), otg_stat);
729
730 switch (musb->xceiv->otg->state) {
731 case OTG_STATE_A_IDLE:
732 dev_dbg(musb->controller, "Got SRP, turning on VBUS\n");
733 musb_platform_set_vbus(musb, 1);
734
735 /* CONNECT can wake if a_wait_bcon is set */
736 if (musb->a_wait_bcon != 0)
737 musb->is_active = 0;
738 else
739 musb->is_active = 1;
740
741 /*
742 * OPT FS A TD.4.6 needs few seconds for
743 * A_WAIT_VRISE
744 */
745 idle_timeout = jiffies + (2 * HZ);
746
747 break;
748 case OTG_STATE_A_WAIT_VRISE:
749 /* ignore; A-session-valid < VBUS_VALID/2,
750 * we monitor this with the timer
751 */
752 break;
753 case OTG_STATE_A_WAIT_VFALL:
754 /* REVISIT this irq triggers during short
755 * spikes caused by enumeration ...
756 */
757 if (musb->vbuserr_retry) {
758 musb->vbuserr_retry--;
759 tusb_musb_set_vbus(musb, 1);
760 } else {
761 musb->vbuserr_retry
762 = VBUSERR_RETRY_COUNT;
763 tusb_musb_set_vbus(musb, 0);
764 }
765 break;
766 default:
767 break;
768 }
769 }
770 }
771
772 /* OTG timer expiration */
773 if (int_src & TUSB_INT_SRC_OTG_TIMEOUT) {
774 u8 devctl;
775
776 dev_dbg(musb->controller, "%s timer, %03x\n",
777 usb_otg_state_string(musb->xceiv->otg->state), otg_stat);
778
779 switch (musb->xceiv->otg->state) {
780 case OTG_STATE_A_WAIT_VRISE:
781 /* VBUS has probably been valid for a while now,
782 * but may well have bounced out of range a bit
783 */
784 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
785 if (otg_stat & TUSB_DEV_OTG_STAT_VBUS_VALID) {
786 if ((devctl & MUSB_DEVCTL_VBUS)
787 != MUSB_DEVCTL_VBUS) {
788 dev_dbg(musb->controller, "devctl %02x\n", devctl);
789 break;
790 }
791 musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
792 musb->is_active = 0;
793 idle_timeout = jiffies
794 + msecs_to_jiffies(musb->a_wait_bcon);
795 } else {
796 /* REVISIT report overcurrent to hub? */
797 ERR("vbus too slow, devctl %02x\n", devctl);
798 tusb_musb_set_vbus(musb, 0);
799 }
800 break;
801 case OTG_STATE_A_WAIT_BCON:
802 if (musb->a_wait_bcon != 0)
803 idle_timeout = jiffies
804 + msecs_to_jiffies(musb->a_wait_bcon);
805 break;
806 case OTG_STATE_A_SUSPEND:
807 break;
808 case OTG_STATE_B_WAIT_ACON:
809 break;
810 default:
811 break;
812 }
813 }
814 schedule_delayed_work(&musb->irq_work, 0);
815
816 return idle_timeout;
817}
818
819static irqreturn_t tusb_musb_interrupt(int irq, void *__hci)
820{
821 struct musb *musb = __hci;
822 void __iomem *tbase = musb->ctrl_base;
823 unsigned long flags, idle_timeout = 0;
824 u32 int_mask, int_src;
825
826 spin_lock_irqsave(&musb->lock, flags);
827
828 /* Mask all interrupts to allow using both edge and level GPIO irq */
829 int_mask = musb_readl(tbase, TUSB_INT_MASK);
830 musb_writel(tbase, TUSB_INT_MASK, ~TUSB_INT_MASK_RESERVED_BITS);
831
832 int_src = musb_readl(tbase, TUSB_INT_SRC) & ~TUSB_INT_SRC_RESERVED_BITS;
833 dev_dbg(musb->controller, "TUSB IRQ %08x\n", int_src);
834
835 musb->int_usb = (u8) int_src;
836
837 /* Acknowledge wake-up source interrupts */
838 if (int_src & TUSB_INT_SRC_DEV_WAKEUP) {
839 u32 reg;
840 u32 i;
841
842 if (musb->tusb_revision == TUSB_REV_30)
843 tusb_wbus_quirk(musb, 0);
844
845 /* there are issues re-locking the PLL on wakeup ... */
846
847 /* work around issue 8 */
848 for (i = 0xf7f7f7; i > 0xf7f7f7 - 1000; i--) {
849 musb_writel(tbase, TUSB_SCRATCH_PAD, 0);
850 musb_writel(tbase, TUSB_SCRATCH_PAD, i);
851 reg = musb_readl(tbase, TUSB_SCRATCH_PAD);
852 if (reg == i)
853 break;
854 dev_dbg(musb->controller, "TUSB NOR not ready\n");
855 }
856
857 /* work around issue 13 (2nd half) */
858 tusb_set_clock_source(musb, 1);
859
860 reg = musb_readl(tbase, TUSB_PRCM_WAKEUP_SOURCE);
861 musb_writel(tbase, TUSB_PRCM_WAKEUP_CLEAR, reg);
862 if (reg & ~TUSB_PRCM_WNORCS) {
863 musb->is_active = 1;
864 schedule_delayed_work(&musb->irq_work, 0);
865 }
866 dev_dbg(musb->controller, "wake %sactive %02x\n",
867 musb->is_active ? "" : "in", reg);
868
869 /* REVISIT host side TUSB_PRCM_WHOSTDISCON, TUSB_PRCM_WBUS */
870 }
871
872 if (int_src & TUSB_INT_SRC_USB_IP_CONN)
873 del_timer(&musb->dev_timer);
874
875 /* OTG state change reports (annoyingly) not issued by Mentor core */
876 if (int_src & (TUSB_INT_SRC_VBUS_SENSE_CHNG
877 | TUSB_INT_SRC_OTG_TIMEOUT
878 | TUSB_INT_SRC_ID_STATUS_CHNG))
879 idle_timeout = tusb_otg_ints(musb, int_src, tbase);
880
881 /*
882 * Just clear the DMA interrupt if it comes as the completion for both
883 * TX and RX is handled by the DMA callback in tusb6010_omap
884 */
885 if ((int_src & TUSB_INT_SRC_TXRX_DMA_DONE)) {
886 u32 dma_src = musb_readl(tbase, TUSB_DMA_INT_SRC);
887
888 dev_dbg(musb->controller, "DMA IRQ %08x\n", dma_src);
889 musb_writel(tbase, TUSB_DMA_INT_CLEAR, dma_src);
890 }
891
892 /* EP interrupts. In OCP mode tusb6010 mirrors the MUSB interrupts */
893 if (int_src & (TUSB_INT_SRC_USB_IP_TX | TUSB_INT_SRC_USB_IP_RX)) {
894 u32 musb_src = musb_readl(tbase, TUSB_USBIP_INT_SRC);
895
896 musb_writel(tbase, TUSB_USBIP_INT_CLEAR, musb_src);
897 musb->int_rx = (((musb_src >> 16) & 0xffff) << 1);
898 musb->int_tx = (musb_src & 0xffff);
899 } else {
900 musb->int_rx = 0;
901 musb->int_tx = 0;
902 }
903
904 if (int_src & (TUSB_INT_SRC_USB_IP_TX | TUSB_INT_SRC_USB_IP_RX | 0xff))
905 musb_interrupt(musb);
906
907 /* Acknowledge TUSB interrupts. Clear only non-reserved bits */
908 musb_writel(tbase, TUSB_INT_SRC_CLEAR,
909 int_src & ~TUSB_INT_MASK_RESERVED_BITS);
910
911 tusb_musb_try_idle(musb, idle_timeout);
912
913 musb_writel(tbase, TUSB_INT_MASK, int_mask);
914 spin_unlock_irqrestore(&musb->lock, flags);
915
916 return IRQ_HANDLED;
917}
918
919static int dma_off;
920
921/*
922 * Enables TUSB6010. Caller must take care of locking.
923 * REVISIT:
924 * - Check what is unnecessary in MGC_HdrcStart()
925 */
926static void tusb_musb_enable(struct musb *musb)
927{
928 void __iomem *tbase = musb->ctrl_base;
929
930 /* Setup TUSB6010 main interrupt mask. Enable all interrupts except SOF.
931 * REVISIT: Enable and deal with TUSB_INT_SRC_USB_IP_SOF */
932 musb_writel(tbase, TUSB_INT_MASK, TUSB_INT_SRC_USB_IP_SOF);
933
934 /* Setup TUSB interrupt, disable DMA and GPIO interrupts */
935 musb_writel(tbase, TUSB_USBIP_INT_MASK, 0);
936 musb_writel(tbase, TUSB_DMA_INT_MASK, 0x7fffffff);
937 musb_writel(tbase, TUSB_GPIO_INT_MASK, 0x1ff);
938
939 /* Clear all subsystem interrups */
940 musb_writel(tbase, TUSB_USBIP_INT_CLEAR, 0x7fffffff);
941 musb_writel(tbase, TUSB_DMA_INT_CLEAR, 0x7fffffff);
942 musb_writel(tbase, TUSB_GPIO_INT_CLEAR, 0x1ff);
943
944 /* Acknowledge pending interrupt(s) */
945 musb_writel(tbase, TUSB_INT_SRC_CLEAR, ~TUSB_INT_MASK_RESERVED_BITS);
946
947 /* Only 0 clock cycles for minimum interrupt de-assertion time and
948 * interrupt polarity active low seems to work reliably here */
949 musb_writel(tbase, TUSB_INT_CTRL_CONF,
950 TUSB_INT_CTRL_CONF_INT_RELCYC(0));
951
952 irq_set_irq_type(musb->nIrq, IRQ_TYPE_LEVEL_LOW);
953
954 /* maybe force into the Default-A OTG state machine */
955 if (!(musb_readl(tbase, TUSB_DEV_OTG_STAT)
956 & TUSB_DEV_OTG_STAT_ID_STATUS))
957 musb_writel(tbase, TUSB_INT_SRC_SET,
958 TUSB_INT_SRC_ID_STATUS_CHNG);
959
960 if (is_dma_capable() && dma_off)
961 printk(KERN_WARNING "%s %s: dma not reactivated\n",
962 __FILE__, __func__);
963 else
964 dma_off = 1;
965}
966
967/*
968 * Disables TUSB6010. Caller must take care of locking.
969 */
970static void tusb_musb_disable(struct musb *musb)
971{
972 void __iomem *tbase = musb->ctrl_base;
973
974 /* FIXME stop DMA, IRQs, timers, ... */
975
976 /* disable all IRQs */
977 musb_writel(tbase, TUSB_INT_MASK, ~TUSB_INT_MASK_RESERVED_BITS);
978 musb_writel(tbase, TUSB_USBIP_INT_MASK, 0x7fffffff);
979 musb_writel(tbase, TUSB_DMA_INT_MASK, 0x7fffffff);
980 musb_writel(tbase, TUSB_GPIO_INT_MASK, 0x1ff);
981
982 del_timer(&musb->dev_timer);
983
984 if (is_dma_capable() && !dma_off) {
985 printk(KERN_WARNING "%s %s: dma still active\n",
986 __FILE__, __func__);
987 dma_off = 1;
988 }
989}
990
991/*
992 * Sets up TUSB6010 CPU interface specific signals and registers
993 * Note: Settings optimized for OMAP24xx
994 */
995static void tusb_setup_cpu_interface(struct musb *musb)
996{
997 void __iomem *tbase = musb->ctrl_base;
998
999 /*
1000 * Disable GPIO[5:0] pullups (used as output DMA requests)
1001 * Don't disable GPIO[7:6] as they are needed for wake-up.
1002 */
1003 musb_writel(tbase, TUSB_PULLUP_1_CTRL, 0x0000003F);
1004
1005 /* Disable all pullups on NOR IF, DMAREQ0 and DMAREQ1 */
1006 musb_writel(tbase, TUSB_PULLUP_2_CTRL, 0x01FFFFFF);
1007
1008 /* Turn GPIO[5:0] to DMAREQ[5:0] signals */
1009 musb_writel(tbase, TUSB_GPIO_CONF, TUSB_GPIO_CONF_DMAREQ(0x3f));
1010
1011 /* Burst size 16x16 bits, all six DMA requests enabled, DMA request
1012 * de-assertion time 2 system clocks p 62 */
1013 musb_writel(tbase, TUSB_DMA_REQ_CONF,
1014 TUSB_DMA_REQ_CONF_BURST_SIZE(2) |
1015 TUSB_DMA_REQ_CONF_DMA_REQ_EN(0x3f) |
1016 TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(2));
1017
1018 /* Set 0 wait count for synchronous burst access */
1019 musb_writel(tbase, TUSB_WAIT_COUNT, 1);
1020}
1021
1022static int tusb_musb_start(struct musb *musb)
1023{
1024 void __iomem *tbase = musb->ctrl_base;
1025 int ret = 0;
1026 unsigned long flags;
1027 u32 reg;
1028
1029 if (musb->board_set_power)
1030 ret = musb->board_set_power(1);
1031 if (ret != 0) {
1032 printk(KERN_ERR "tusb: Cannot enable TUSB6010\n");
1033 return ret;
1034 }
1035
1036 spin_lock_irqsave(&musb->lock, flags);
1037
1038 if (musb_readl(tbase, TUSB_PROD_TEST_RESET) !=
1039 TUSB_PROD_TEST_RESET_VAL) {
1040 printk(KERN_ERR "tusb: Unable to detect TUSB6010\n");
1041 goto err;
1042 }
1043
1044 musb->tusb_revision = tusb_get_revision(musb);
1045 tusb_print_revision(musb);
1046 if (musb->tusb_revision < 2) {
1047 printk(KERN_ERR "tusb: Unsupported TUSB6010 revision %i\n",
1048 musb->tusb_revision);
1049 goto err;
1050 }
1051
1052 /* The uint bit for "USB non-PDR interrupt enable" has to be 1 when
1053 * NOR FLASH interface is used */
1054 musb_writel(tbase, TUSB_VLYNQ_CTRL, 8);
1055
1056 /* Select PHY free running 60MHz as a system clock */
1057 tusb_set_clock_source(musb, 1);
1058
1059 /* VBus valid timer 1us, disable DFT/Debug and VLYNQ clocks for
1060 * power saving, enable VBus detect and session end comparators,
1061 * enable IDpullup, enable VBus charging */
1062 musb_writel(tbase, TUSB_PRCM_MNGMT,
1063 TUSB_PRCM_MNGMT_VBUS_VALID_TIMER(0xa) |
1064 TUSB_PRCM_MNGMT_VBUS_VALID_FLT_EN |
1065 TUSB_PRCM_MNGMT_OTG_SESS_END_EN |
1066 TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN |
1067 TUSB_PRCM_MNGMT_OTG_ID_PULLUP);
1068 tusb_setup_cpu_interface(musb);
1069
1070 /* simplify: always sense/pullup ID pins, as if in OTG mode */
1071 reg = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE);
1072 reg |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
1073 musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, reg);
1074
1075 reg = musb_readl(tbase, TUSB_PHY_OTG_CTRL);
1076 reg |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
1077 musb_writel(tbase, TUSB_PHY_OTG_CTRL, reg);
1078
1079 spin_unlock_irqrestore(&musb->lock, flags);
1080
1081 return 0;
1082
1083err:
1084 spin_unlock_irqrestore(&musb->lock, flags);
1085
1086 if (musb->board_set_power)
1087 musb->board_set_power(0);
1088
1089 return -ENODEV;
1090}
1091
1092static int tusb_musb_init(struct musb *musb)
1093{
1094 struct platform_device *pdev;
1095 struct resource *mem;
1096 void __iomem *sync = NULL;
1097 int ret;
1098
1099 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
1100 if (IS_ERR_OR_NULL(musb->xceiv))
1101 return -EPROBE_DEFER;
1102
1103 pdev = to_platform_device(musb->controller);
1104
1105 /* dma address for async dma */
1106 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1107 if (!mem) {
1108 pr_debug("no async dma resource?\n");
1109 ret = -ENODEV;
1110 goto done;
1111 }
1112 musb->async = mem->start;
1113
1114 /* dma address for sync dma */
1115 mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
1116 if (!mem) {
1117 pr_debug("no sync dma resource?\n");
1118 ret = -ENODEV;
1119 goto done;
1120 }
1121 musb->sync = mem->start;
1122
1123 sync = ioremap(mem->start, resource_size(mem));
1124 if (!sync) {
1125 pr_debug("ioremap for sync failed\n");
1126 ret = -ENOMEM;
1127 goto done;
1128 }
1129 musb->sync_va = sync;
1130
1131 /* Offsets from base: VLYNQ at 0x000, MUSB regs at 0x400,
1132 * FIFOs at 0x600, TUSB at 0x800
1133 */
1134 musb->mregs += TUSB_BASE_OFFSET;
1135
1136 ret = tusb_musb_start(musb);
1137 if (ret) {
1138 printk(KERN_ERR "Could not start tusb6010 (%d)\n",
1139 ret);
1140 goto done;
1141 }
1142 musb->isr = tusb_musb_interrupt;
1143
1144 musb->xceiv->set_power = tusb_draw_power;
1145 the_musb = musb;
1146
1147 timer_setup(&musb->dev_timer, musb_do_idle, 0);
1148
1149done:
1150 if (ret < 0) {
1151 if (sync)
1152 iounmap(sync);
1153
1154 usb_put_phy(musb->xceiv);
1155 }
1156 return ret;
1157}
1158
1159static int tusb_musb_exit(struct musb *musb)
1160{
1161 del_timer_sync(&musb->dev_timer);
1162 the_musb = NULL;
1163
1164 if (musb->board_set_power)
1165 musb->board_set_power(0);
1166
1167 iounmap(musb->sync_va);
1168
1169 usb_put_phy(musb->xceiv);
1170 return 0;
1171}
1172
1173static const struct musb_platform_ops tusb_ops = {
1174 .quirks = MUSB_DMA_TUSB_OMAP | MUSB_IN_TUSB |
1175 MUSB_G_NO_SKB_RESERVE,
1176 .init = tusb_musb_init,
1177 .exit = tusb_musb_exit,
1178
1179 .ep_offset = tusb_ep_offset,
1180 .ep_select = tusb_ep_select,
1181 .fifo_offset = tusb_fifo_offset,
1182 .readb = tusb_readb,
1183 .writeb = tusb_writeb,
1184 .read_fifo = tusb_read_fifo,
1185 .write_fifo = tusb_write_fifo,
1186#ifdef CONFIG_USB_TUSB_OMAP_DMA
1187 .dma_init = tusb_dma_controller_create,
1188 .dma_exit = tusb_dma_controller_destroy,
1189#endif
1190 .enable = tusb_musb_enable,
1191 .disable = tusb_musb_disable,
1192
1193 .set_mode = tusb_musb_set_mode,
1194 .try_idle = tusb_musb_try_idle,
1195
1196 .vbus_status = tusb_musb_vbus_status,
1197 .set_vbus = tusb_musb_set_vbus,
1198};
1199
1200static const struct platform_device_info tusb_dev_info = {
1201 .name = "musb-hdrc",
1202 .id = PLATFORM_DEVID_AUTO,
1203 .dma_mask = DMA_BIT_MASK(32),
1204};
1205
1206static int tusb_probe(struct platform_device *pdev)
1207{
1208 struct resource musb_resources[3];
1209 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
1210 struct platform_device *musb;
1211 struct tusb6010_glue *glue;
1212 struct platform_device_info pinfo;
1213 int ret;
1214
1215 glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
1216 if (!glue)
1217 return -ENOMEM;
1218
1219 glue->dev = &pdev->dev;
1220
1221 pdata->platform_ops = &tusb_ops;
1222
1223 usb_phy_generic_register();
1224 platform_set_drvdata(pdev, glue);
1225
1226 memset(musb_resources, 0x00, sizeof(*musb_resources) *
1227 ARRAY_SIZE(musb_resources));
1228
1229 musb_resources[0].name = pdev->resource[0].name;
1230 musb_resources[0].start = pdev->resource[0].start;
1231 musb_resources[0].end = pdev->resource[0].end;
1232 musb_resources[0].flags = pdev->resource[0].flags;
1233
1234 musb_resources[1].name = pdev->resource[1].name;
1235 musb_resources[1].start = pdev->resource[1].start;
1236 musb_resources[1].end = pdev->resource[1].end;
1237 musb_resources[1].flags = pdev->resource[1].flags;
1238
1239 musb_resources[2].name = pdev->resource[2].name;
1240 musb_resources[2].start = pdev->resource[2].start;
1241 musb_resources[2].end = pdev->resource[2].end;
1242 musb_resources[2].flags = pdev->resource[2].flags;
1243
1244 pinfo = tusb_dev_info;
1245 pinfo.parent = &pdev->dev;
1246 pinfo.res = musb_resources;
1247 pinfo.num_res = ARRAY_SIZE(musb_resources);
1248 pinfo.data = pdata;
1249 pinfo.size_data = sizeof(*pdata);
1250
1251 glue->musb = musb = platform_device_register_full(&pinfo);
1252 if (IS_ERR(musb)) {
1253 ret = PTR_ERR(musb);
1254 dev_err(&pdev->dev, "failed to register musb device: %d\n", ret);
1255 return ret;
1256 }
1257
1258 return 0;
1259}
1260
1261static int tusb_remove(struct platform_device *pdev)
1262{
1263 struct tusb6010_glue *glue = platform_get_drvdata(pdev);
1264
1265 platform_device_unregister(glue->musb);
1266 usb_phy_generic_unregister(glue->phy);
1267
1268 return 0;
1269}
1270
1271static struct platform_driver tusb_driver = {
1272 .probe = tusb_probe,
1273 .remove = tusb_remove,
1274 .driver = {
1275 .name = "musb-tusb",
1276 },
1277};
1278
1279MODULE_DESCRIPTION("TUSB6010 MUSB Glue Layer");
1280MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
1281MODULE_LICENSE("GPL v2");
1282module_platform_driver(tusb_driver);