Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Driver for CLPS711x serial ports
4 *
5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
6 *
7 * Copyright 1999 ARM Limited
8 * Copyright (C) 2000 Deep Blue Solutions Ltd.
9 */
10
11#include <linux/module.h>
12#include <linux/device.h>
13#include <linux/console.h>
14#include <linux/serial_core.h>
15#include <linux/serial.h>
16#include <linux/clk.h>
17#include <linux/io.h>
18#include <linux/tty.h>
19#include <linux/tty_flip.h>
20#include <linux/ioport.h>
21#include <linux/of.h>
22#include <linux/platform_device.h>
23#include <linux/regmap.h>
24
25#include <linux/mfd/syscon.h>
26#include <linux/mfd/syscon/clps711x.h>
27
28#include "serial_mctrl_gpio.h"
29
30#define UART_CLPS711X_DEVNAME "ttyCL"
31#define UART_CLPS711X_NR 2
32#define UART_CLPS711X_MAJOR 204
33#define UART_CLPS711X_MINOR 40
34
35#define UARTDR_OFFSET (0x00)
36#define UBRLCR_OFFSET (0x40)
37
38#define UARTDR_FRMERR (1 << 8)
39#define UARTDR_PARERR (1 << 9)
40#define UARTDR_OVERR (1 << 10)
41
42#define UBRLCR_BAUD_MASK ((1 << 12) - 1)
43#define UBRLCR_BREAK (1 << 12)
44#define UBRLCR_PRTEN (1 << 13)
45#define UBRLCR_EVENPRT (1 << 14)
46#define UBRLCR_XSTOP (1 << 15)
47#define UBRLCR_FIFOEN (1 << 16)
48#define UBRLCR_WRDLEN5 (0 << 17)
49#define UBRLCR_WRDLEN6 (1 << 17)
50#define UBRLCR_WRDLEN7 (2 << 17)
51#define UBRLCR_WRDLEN8 (3 << 17)
52#define UBRLCR_WRDLEN_MASK (3 << 17)
53
54struct clps711x_port {
55 struct uart_port port;
56 unsigned int tx_enabled;
57 int rx_irq;
58 struct regmap *syscon;
59 struct mctrl_gpios *gpios;
60};
61
62static struct uart_driver clps711x_uart = {
63 .owner = THIS_MODULE,
64 .driver_name = UART_CLPS711X_DEVNAME,
65 .dev_name = UART_CLPS711X_DEVNAME,
66 .major = UART_CLPS711X_MAJOR,
67 .minor = UART_CLPS711X_MINOR,
68 .nr = UART_CLPS711X_NR,
69};
70
71static void uart_clps711x_stop_tx(struct uart_port *port)
72{
73 struct clps711x_port *s = dev_get_drvdata(port->dev);
74
75 if (s->tx_enabled) {
76 disable_irq(port->irq);
77 s->tx_enabled = 0;
78 }
79}
80
81static void uart_clps711x_start_tx(struct uart_port *port)
82{
83 struct clps711x_port *s = dev_get_drvdata(port->dev);
84
85 if (!s->tx_enabled) {
86 s->tx_enabled = 1;
87 enable_irq(port->irq);
88 }
89}
90
91static irqreturn_t uart_clps711x_int_rx(int irq, void *dev_id)
92{
93 struct uart_port *port = dev_id;
94 struct clps711x_port *s = dev_get_drvdata(port->dev);
95 unsigned int status;
96 u16 ch;
97 u8 flg;
98
99 for (;;) {
100 u32 sysflg = 0;
101
102 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
103 if (sysflg & SYSFLG_URXFE)
104 break;
105
106 ch = readw(port->membase + UARTDR_OFFSET);
107 status = ch & (UARTDR_FRMERR | UARTDR_PARERR | UARTDR_OVERR);
108 ch &= 0xff;
109
110 port->icount.rx++;
111 flg = TTY_NORMAL;
112
113 if (unlikely(status)) {
114 if (status & UARTDR_PARERR)
115 port->icount.parity++;
116 else if (status & UARTDR_FRMERR)
117 port->icount.frame++;
118 else if (status & UARTDR_OVERR)
119 port->icount.overrun++;
120
121 status &= port->read_status_mask;
122
123 if (status & UARTDR_PARERR)
124 flg = TTY_PARITY;
125 else if (status & UARTDR_FRMERR)
126 flg = TTY_FRAME;
127 else if (status & UARTDR_OVERR)
128 flg = TTY_OVERRUN;
129 }
130
131 if (uart_handle_sysrq_char(port, ch))
132 continue;
133
134 if (status & port->ignore_status_mask)
135 continue;
136
137 uart_insert_char(port, status, UARTDR_OVERR, ch, flg);
138 }
139
140 tty_flip_buffer_push(&port->state->port);
141
142 return IRQ_HANDLED;
143}
144
145static irqreturn_t uart_clps711x_int_tx(int irq, void *dev_id)
146{
147 struct uart_port *port = dev_id;
148 struct clps711x_port *s = dev_get_drvdata(port->dev);
149 struct circ_buf *xmit = &port->state->xmit;
150
151 if (port->x_char) {
152 writew(port->x_char, port->membase + UARTDR_OFFSET);
153 port->icount.tx++;
154 port->x_char = 0;
155 return IRQ_HANDLED;
156 }
157
158 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
159 if (s->tx_enabled) {
160 disable_irq_nosync(port->irq);
161 s->tx_enabled = 0;
162 }
163 return IRQ_HANDLED;
164 }
165
166 while (!uart_circ_empty(xmit)) {
167 u32 sysflg = 0;
168
169 writew(xmit->buf[xmit->tail], port->membase + UARTDR_OFFSET);
170 uart_xmit_advance(port, 1);
171
172 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
173 if (sysflg & SYSFLG_UTXFF)
174 break;
175 }
176
177 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
178 uart_write_wakeup(port);
179
180 return IRQ_HANDLED;
181}
182
183static unsigned int uart_clps711x_tx_empty(struct uart_port *port)
184{
185 struct clps711x_port *s = dev_get_drvdata(port->dev);
186 u32 sysflg = 0;
187
188 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
189
190 return (sysflg & SYSFLG_UBUSY) ? 0 : TIOCSER_TEMT;
191}
192
193static unsigned int uart_clps711x_get_mctrl(struct uart_port *port)
194{
195 unsigned int result = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
196 struct clps711x_port *s = dev_get_drvdata(port->dev);
197
198 return mctrl_gpio_get(s->gpios, &result);
199}
200
201static void uart_clps711x_set_mctrl(struct uart_port *port, unsigned int mctrl)
202{
203 struct clps711x_port *s = dev_get_drvdata(port->dev);
204
205 mctrl_gpio_set(s->gpios, mctrl);
206}
207
208static void uart_clps711x_break_ctl(struct uart_port *port, int break_state)
209{
210 unsigned int ubrlcr;
211
212 ubrlcr = readl(port->membase + UBRLCR_OFFSET);
213 if (break_state)
214 ubrlcr |= UBRLCR_BREAK;
215 else
216 ubrlcr &= ~UBRLCR_BREAK;
217 writel(ubrlcr, port->membase + UBRLCR_OFFSET);
218}
219
220static void uart_clps711x_set_ldisc(struct uart_port *port,
221 struct ktermios *termios)
222{
223 if (!port->line) {
224 struct clps711x_port *s = dev_get_drvdata(port->dev);
225
226 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON1_SIREN,
227 (termios->c_line == N_IRDA) ? SYSCON1_SIREN : 0);
228 }
229}
230
231static int uart_clps711x_startup(struct uart_port *port)
232{
233 struct clps711x_port *s = dev_get_drvdata(port->dev);
234
235 /* Disable break */
236 writel(readl(port->membase + UBRLCR_OFFSET) & ~UBRLCR_BREAK,
237 port->membase + UBRLCR_OFFSET);
238
239 /* Enable the port */
240 return regmap_update_bits(s->syscon, SYSCON_OFFSET,
241 SYSCON_UARTEN, SYSCON_UARTEN);
242}
243
244static void uart_clps711x_shutdown(struct uart_port *port)
245{
246 struct clps711x_port *s = dev_get_drvdata(port->dev);
247
248 /* Disable the port */
249 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
250}
251
252static void uart_clps711x_set_termios(struct uart_port *port,
253 struct ktermios *termios,
254 const struct ktermios *old)
255{
256 u32 ubrlcr;
257 unsigned int baud, quot;
258
259 /* Mask termios capabilities we don't support */
260 termios->c_cflag &= ~CMSPAR;
261 termios->c_iflag &= ~(BRKINT | IGNBRK);
262
263 /* Ask the core to calculate the divisor for us */
264 baud = uart_get_baud_rate(port, termios, old, port->uartclk / 4096,
265 port->uartclk / 16);
266 quot = uart_get_divisor(port, baud);
267
268 switch (termios->c_cflag & CSIZE) {
269 case CS5:
270 ubrlcr = UBRLCR_WRDLEN5;
271 break;
272 case CS6:
273 ubrlcr = UBRLCR_WRDLEN6;
274 break;
275 case CS7:
276 ubrlcr = UBRLCR_WRDLEN7;
277 break;
278 case CS8:
279 default:
280 ubrlcr = UBRLCR_WRDLEN8;
281 break;
282 }
283
284 if (termios->c_cflag & CSTOPB)
285 ubrlcr |= UBRLCR_XSTOP;
286
287 if (termios->c_cflag & PARENB) {
288 ubrlcr |= UBRLCR_PRTEN;
289 if (!(termios->c_cflag & PARODD))
290 ubrlcr |= UBRLCR_EVENPRT;
291 }
292
293 /* Enable FIFO */
294 ubrlcr |= UBRLCR_FIFOEN;
295
296 /* Set read status mask */
297 port->read_status_mask = UARTDR_OVERR;
298 if (termios->c_iflag & INPCK)
299 port->read_status_mask |= UARTDR_PARERR | UARTDR_FRMERR;
300
301 /* Set status ignore mask */
302 port->ignore_status_mask = 0;
303 if (!(termios->c_cflag & CREAD))
304 port->ignore_status_mask |= UARTDR_OVERR | UARTDR_PARERR |
305 UARTDR_FRMERR;
306
307 uart_update_timeout(port, termios->c_cflag, baud);
308
309 writel(ubrlcr | (quot - 1), port->membase + UBRLCR_OFFSET);
310}
311
312static const char *uart_clps711x_type(struct uart_port *port)
313{
314 return (port->type == PORT_CLPS711X) ? "CLPS711X" : NULL;
315}
316
317static void uart_clps711x_config_port(struct uart_port *port, int flags)
318{
319 if (flags & UART_CONFIG_TYPE)
320 port->type = PORT_CLPS711X;
321}
322
323static void uart_clps711x_nop_void(struct uart_port *port)
324{
325}
326
327static int uart_clps711x_nop_int(struct uart_port *port)
328{
329 return 0;
330}
331
332static const struct uart_ops uart_clps711x_ops = {
333 .tx_empty = uart_clps711x_tx_empty,
334 .set_mctrl = uart_clps711x_set_mctrl,
335 .get_mctrl = uart_clps711x_get_mctrl,
336 .stop_tx = uart_clps711x_stop_tx,
337 .start_tx = uart_clps711x_start_tx,
338 .stop_rx = uart_clps711x_nop_void,
339 .break_ctl = uart_clps711x_break_ctl,
340 .set_ldisc = uart_clps711x_set_ldisc,
341 .startup = uart_clps711x_startup,
342 .shutdown = uart_clps711x_shutdown,
343 .set_termios = uart_clps711x_set_termios,
344 .type = uart_clps711x_type,
345 .config_port = uart_clps711x_config_port,
346 .release_port = uart_clps711x_nop_void,
347 .request_port = uart_clps711x_nop_int,
348};
349
350#ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
351static void uart_clps711x_console_putchar(struct uart_port *port, unsigned char ch)
352{
353 struct clps711x_port *s = dev_get_drvdata(port->dev);
354 u32 sysflg = 0;
355
356 /* Wait for FIFO is not full */
357 do {
358 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
359 } while (sysflg & SYSFLG_UTXFF);
360
361 writew(ch, port->membase + UARTDR_OFFSET);
362}
363
364static void uart_clps711x_console_write(struct console *co, const char *c,
365 unsigned n)
366{
367 struct uart_port *port = clps711x_uart.state[co->index].uart_port;
368 struct clps711x_port *s = dev_get_drvdata(port->dev);
369 u32 sysflg = 0;
370
371 uart_console_write(port, c, n, uart_clps711x_console_putchar);
372
373 /* Wait for transmitter to become empty */
374 do {
375 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
376 } while (sysflg & SYSFLG_UBUSY);
377}
378
379static int uart_clps711x_console_setup(struct console *co, char *options)
380{
381 int baud = 38400, bits = 8, parity = 'n', flow = 'n';
382 int ret, index = co->index;
383 struct clps711x_port *s;
384 struct uart_port *port;
385 unsigned int quot;
386 u32 ubrlcr;
387
388 if (index < 0 || index >= UART_CLPS711X_NR)
389 return -EINVAL;
390
391 port = clps711x_uart.state[index].uart_port;
392 if (!port)
393 return -ENODEV;
394
395 s = dev_get_drvdata(port->dev);
396
397 if (!options) {
398 u32 syscon = 0;
399
400 regmap_read(s->syscon, SYSCON_OFFSET, &syscon);
401 if (syscon & SYSCON_UARTEN) {
402 ubrlcr = readl(port->membase + UBRLCR_OFFSET);
403
404 if (ubrlcr & UBRLCR_PRTEN) {
405 if (ubrlcr & UBRLCR_EVENPRT)
406 parity = 'e';
407 else
408 parity = 'o';
409 }
410
411 if ((ubrlcr & UBRLCR_WRDLEN_MASK) == UBRLCR_WRDLEN7)
412 bits = 7;
413
414 quot = ubrlcr & UBRLCR_BAUD_MASK;
415 baud = port->uartclk / (16 * (quot + 1));
416 }
417 } else
418 uart_parse_options(options, &baud, &parity, &bits, &flow);
419
420 ret = uart_set_options(port, co, baud, parity, bits, flow);
421 if (ret)
422 return ret;
423
424 return regmap_update_bits(s->syscon, SYSCON_OFFSET,
425 SYSCON_UARTEN, SYSCON_UARTEN);
426}
427
428static struct console clps711x_console = {
429 .name = UART_CLPS711X_DEVNAME,
430 .device = uart_console_device,
431 .write = uart_clps711x_console_write,
432 .setup = uart_clps711x_console_setup,
433 .flags = CON_PRINTBUFFER,
434 .index = -1,
435};
436#endif
437
438static int uart_clps711x_probe(struct platform_device *pdev)
439{
440 struct device_node *np = pdev->dev.of_node;
441 struct clps711x_port *s;
442 struct resource *res;
443 struct clk *uart_clk;
444 int irq, ret;
445
446 s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL);
447 if (!s)
448 return -ENOMEM;
449
450 uart_clk = devm_clk_get(&pdev->dev, NULL);
451 if (IS_ERR(uart_clk))
452 return PTR_ERR(uart_clk);
453
454 s->port.membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
455 if (IS_ERR(s->port.membase))
456 return PTR_ERR(s->port.membase);
457
458 irq = platform_get_irq(pdev, 0);
459 if (irq < 0)
460 return irq;
461 s->port.irq = irq;
462
463 s->rx_irq = platform_get_irq(pdev, 1);
464 if (s->rx_irq < 0)
465 return s->rx_irq;
466
467 s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon");
468 if (IS_ERR(s->syscon))
469 return PTR_ERR(s->syscon);
470
471 s->port.line = of_alias_get_id(np, "serial");
472 s->port.dev = &pdev->dev;
473 s->port.iotype = UPIO_MEM32;
474 s->port.mapbase = res->start;
475 s->port.type = PORT_CLPS711X;
476 s->port.fifosize = 16;
477 s->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_CLPS711X_CONSOLE);
478 s->port.flags = UPF_SKIP_TEST | UPF_FIXED_TYPE;
479 s->port.uartclk = clk_get_rate(uart_clk);
480 s->port.ops = &uart_clps711x_ops;
481
482 platform_set_drvdata(pdev, s);
483
484 s->gpios = mctrl_gpio_init_noauto(&pdev->dev, 0);
485 if (IS_ERR(s->gpios))
486 return PTR_ERR(s->gpios);
487
488 ret = uart_add_one_port(&clps711x_uart, &s->port);
489 if (ret)
490 return ret;
491
492 /* Disable port */
493 if (!uart_console(&s->port))
494 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
495
496 s->tx_enabled = 1;
497
498 ret = devm_request_irq(&pdev->dev, s->port.irq, uart_clps711x_int_tx, 0,
499 dev_name(&pdev->dev), &s->port);
500 if (ret) {
501 uart_remove_one_port(&clps711x_uart, &s->port);
502 return ret;
503 }
504
505 ret = devm_request_irq(&pdev->dev, s->rx_irq, uart_clps711x_int_rx, 0,
506 dev_name(&pdev->dev), &s->port);
507 if (ret)
508 uart_remove_one_port(&clps711x_uart, &s->port);
509
510 return ret;
511}
512
513static void uart_clps711x_remove(struct platform_device *pdev)
514{
515 struct clps711x_port *s = platform_get_drvdata(pdev);
516
517 uart_remove_one_port(&clps711x_uart, &s->port);
518}
519
520static const struct of_device_id __maybe_unused clps711x_uart_dt_ids[] = {
521 { .compatible = "cirrus,ep7209-uart", },
522 { }
523};
524MODULE_DEVICE_TABLE(of, clps711x_uart_dt_ids);
525
526static struct platform_driver clps711x_uart_platform = {
527 .driver = {
528 .name = "clps711x-uart",
529 .of_match_table = of_match_ptr(clps711x_uart_dt_ids),
530 },
531 .probe = uart_clps711x_probe,
532 .remove_new = uart_clps711x_remove,
533};
534
535static int __init uart_clps711x_init(void)
536{
537 int ret;
538
539#ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
540 clps711x_uart.cons = &clps711x_console;
541 clps711x_console.data = &clps711x_uart;
542#endif
543
544 ret = uart_register_driver(&clps711x_uart);
545 if (ret)
546 return ret;
547
548 return platform_driver_register(&clps711x_uart_platform);
549}
550module_init(uart_clps711x_init);
551
552static void __exit uart_clps711x_exit(void)
553{
554 platform_driver_unregister(&clps711x_uart_platform);
555 uart_unregister_driver(&clps711x_uart);
556}
557module_exit(uart_clps711x_exit);
558
559MODULE_AUTHOR("Deep Blue Solutions Ltd");
560MODULE_DESCRIPTION("CLPS711X serial driver");
561MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Driver for CLPS711x serial ports
4 *
5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
6 *
7 * Copyright 1999 ARM Limited
8 * Copyright (C) 2000 Deep Blue Solutions Ltd.
9 */
10
11#include <linux/module.h>
12#include <linux/device.h>
13#include <linux/console.h>
14#include <linux/serial_core.h>
15#include <linux/serial.h>
16#include <linux/clk.h>
17#include <linux/io.h>
18#include <linux/tty.h>
19#include <linux/tty_flip.h>
20#include <linux/ioport.h>
21#include <linux/of.h>
22#include <linux/platform_device.h>
23#include <linux/regmap.h>
24
25#include <linux/mfd/syscon.h>
26#include <linux/mfd/syscon/clps711x.h>
27
28#include "serial_mctrl_gpio.h"
29
30#define UART_CLPS711X_DEVNAME "ttyCL"
31#define UART_CLPS711X_NR 2
32#define UART_CLPS711X_MAJOR 204
33#define UART_CLPS711X_MINOR 40
34
35#define UARTDR_OFFSET (0x00)
36#define UBRLCR_OFFSET (0x40)
37
38#define UARTDR_FRMERR (1 << 8)
39#define UARTDR_PARERR (1 << 9)
40#define UARTDR_OVERR (1 << 10)
41
42#define UBRLCR_BAUD_MASK ((1 << 12) - 1)
43#define UBRLCR_BREAK (1 << 12)
44#define UBRLCR_PRTEN (1 << 13)
45#define UBRLCR_EVENPRT (1 << 14)
46#define UBRLCR_XSTOP (1 << 15)
47#define UBRLCR_FIFOEN (1 << 16)
48#define UBRLCR_WRDLEN5 (0 << 17)
49#define UBRLCR_WRDLEN6 (1 << 17)
50#define UBRLCR_WRDLEN7 (2 << 17)
51#define UBRLCR_WRDLEN8 (3 << 17)
52#define UBRLCR_WRDLEN_MASK (3 << 17)
53
54struct clps711x_port {
55 struct uart_port port;
56 unsigned int tx_enabled;
57 int rx_irq;
58 struct regmap *syscon;
59 struct mctrl_gpios *gpios;
60};
61
62static struct uart_driver clps711x_uart = {
63 .owner = THIS_MODULE,
64 .driver_name = UART_CLPS711X_DEVNAME,
65 .dev_name = UART_CLPS711X_DEVNAME,
66 .major = UART_CLPS711X_MAJOR,
67 .minor = UART_CLPS711X_MINOR,
68 .nr = UART_CLPS711X_NR,
69};
70
71static void uart_clps711x_stop_tx(struct uart_port *port)
72{
73 struct clps711x_port *s = dev_get_drvdata(port->dev);
74
75 if (s->tx_enabled) {
76 disable_irq(port->irq);
77 s->tx_enabled = 0;
78 }
79}
80
81static void uart_clps711x_start_tx(struct uart_port *port)
82{
83 struct clps711x_port *s = dev_get_drvdata(port->dev);
84
85 if (!s->tx_enabled) {
86 s->tx_enabled = 1;
87 enable_irq(port->irq);
88 }
89}
90
91static irqreturn_t uart_clps711x_int_rx(int irq, void *dev_id)
92{
93 struct uart_port *port = dev_id;
94 struct clps711x_port *s = dev_get_drvdata(port->dev);
95 unsigned int status, flg;
96 u16 ch;
97
98 for (;;) {
99 u32 sysflg = 0;
100
101 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
102 if (sysflg & SYSFLG_URXFE)
103 break;
104
105 ch = readw(port->membase + UARTDR_OFFSET);
106 status = ch & (UARTDR_FRMERR | UARTDR_PARERR | UARTDR_OVERR);
107 ch &= 0xff;
108
109 port->icount.rx++;
110 flg = TTY_NORMAL;
111
112 if (unlikely(status)) {
113 if (status & UARTDR_PARERR)
114 port->icount.parity++;
115 else if (status & UARTDR_FRMERR)
116 port->icount.frame++;
117 else if (status & UARTDR_OVERR)
118 port->icount.overrun++;
119
120 status &= port->read_status_mask;
121
122 if (status & UARTDR_PARERR)
123 flg = TTY_PARITY;
124 else if (status & UARTDR_FRMERR)
125 flg = TTY_FRAME;
126 else if (status & UARTDR_OVERR)
127 flg = TTY_OVERRUN;
128 }
129
130 if (uart_handle_sysrq_char(port, ch))
131 continue;
132
133 if (status & port->ignore_status_mask)
134 continue;
135
136 uart_insert_char(port, status, UARTDR_OVERR, ch, flg);
137 }
138
139 tty_flip_buffer_push(&port->state->port);
140
141 return IRQ_HANDLED;
142}
143
144static irqreturn_t uart_clps711x_int_tx(int irq, void *dev_id)
145{
146 struct uart_port *port = dev_id;
147 struct clps711x_port *s = dev_get_drvdata(port->dev);
148 struct circ_buf *xmit = &port->state->xmit;
149
150 if (port->x_char) {
151 writew(port->x_char, port->membase + UARTDR_OFFSET);
152 port->icount.tx++;
153 port->x_char = 0;
154 return IRQ_HANDLED;
155 }
156
157 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
158 if (s->tx_enabled) {
159 disable_irq_nosync(port->irq);
160 s->tx_enabled = 0;
161 }
162 return IRQ_HANDLED;
163 }
164
165 while (!uart_circ_empty(xmit)) {
166 u32 sysflg = 0;
167
168 writew(xmit->buf[xmit->tail], port->membase + UARTDR_OFFSET);
169 uart_xmit_advance(port, 1);
170
171 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
172 if (sysflg & SYSFLG_UTXFF)
173 break;
174 }
175
176 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
177 uart_write_wakeup(port);
178
179 return IRQ_HANDLED;
180}
181
182static unsigned int uart_clps711x_tx_empty(struct uart_port *port)
183{
184 struct clps711x_port *s = dev_get_drvdata(port->dev);
185 u32 sysflg = 0;
186
187 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
188
189 return (sysflg & SYSFLG_UBUSY) ? 0 : TIOCSER_TEMT;
190}
191
192static unsigned int uart_clps711x_get_mctrl(struct uart_port *port)
193{
194 unsigned int result = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
195 struct clps711x_port *s = dev_get_drvdata(port->dev);
196
197 return mctrl_gpio_get(s->gpios, &result);
198}
199
200static void uart_clps711x_set_mctrl(struct uart_port *port, unsigned int mctrl)
201{
202 struct clps711x_port *s = dev_get_drvdata(port->dev);
203
204 mctrl_gpio_set(s->gpios, mctrl);
205}
206
207static void uart_clps711x_break_ctl(struct uart_port *port, int break_state)
208{
209 unsigned int ubrlcr;
210
211 ubrlcr = readl(port->membase + UBRLCR_OFFSET);
212 if (break_state)
213 ubrlcr |= UBRLCR_BREAK;
214 else
215 ubrlcr &= ~UBRLCR_BREAK;
216 writel(ubrlcr, port->membase + UBRLCR_OFFSET);
217}
218
219static void uart_clps711x_set_ldisc(struct uart_port *port,
220 struct ktermios *termios)
221{
222 if (!port->line) {
223 struct clps711x_port *s = dev_get_drvdata(port->dev);
224
225 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON1_SIREN,
226 (termios->c_line == N_IRDA) ? SYSCON1_SIREN : 0);
227 }
228}
229
230static int uart_clps711x_startup(struct uart_port *port)
231{
232 struct clps711x_port *s = dev_get_drvdata(port->dev);
233
234 /* Disable break */
235 writel(readl(port->membase + UBRLCR_OFFSET) & ~UBRLCR_BREAK,
236 port->membase + UBRLCR_OFFSET);
237
238 /* Enable the port */
239 return regmap_update_bits(s->syscon, SYSCON_OFFSET,
240 SYSCON_UARTEN, SYSCON_UARTEN);
241}
242
243static void uart_clps711x_shutdown(struct uart_port *port)
244{
245 struct clps711x_port *s = dev_get_drvdata(port->dev);
246
247 /* Disable the port */
248 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
249}
250
251static void uart_clps711x_set_termios(struct uart_port *port,
252 struct ktermios *termios,
253 const struct ktermios *old)
254{
255 u32 ubrlcr;
256 unsigned int baud, quot;
257
258 /* Mask termios capabilities we don't support */
259 termios->c_cflag &= ~CMSPAR;
260 termios->c_iflag &= ~(BRKINT | IGNBRK);
261
262 /* Ask the core to calculate the divisor for us */
263 baud = uart_get_baud_rate(port, termios, old, port->uartclk / 4096,
264 port->uartclk / 16);
265 quot = uart_get_divisor(port, baud);
266
267 switch (termios->c_cflag & CSIZE) {
268 case CS5:
269 ubrlcr = UBRLCR_WRDLEN5;
270 break;
271 case CS6:
272 ubrlcr = UBRLCR_WRDLEN6;
273 break;
274 case CS7:
275 ubrlcr = UBRLCR_WRDLEN7;
276 break;
277 case CS8:
278 default:
279 ubrlcr = UBRLCR_WRDLEN8;
280 break;
281 }
282
283 if (termios->c_cflag & CSTOPB)
284 ubrlcr |= UBRLCR_XSTOP;
285
286 if (termios->c_cflag & PARENB) {
287 ubrlcr |= UBRLCR_PRTEN;
288 if (!(termios->c_cflag & PARODD))
289 ubrlcr |= UBRLCR_EVENPRT;
290 }
291
292 /* Enable FIFO */
293 ubrlcr |= UBRLCR_FIFOEN;
294
295 /* Set read status mask */
296 port->read_status_mask = UARTDR_OVERR;
297 if (termios->c_iflag & INPCK)
298 port->read_status_mask |= UARTDR_PARERR | UARTDR_FRMERR;
299
300 /* Set status ignore mask */
301 port->ignore_status_mask = 0;
302 if (!(termios->c_cflag & CREAD))
303 port->ignore_status_mask |= UARTDR_OVERR | UARTDR_PARERR |
304 UARTDR_FRMERR;
305
306 uart_update_timeout(port, termios->c_cflag, baud);
307
308 writel(ubrlcr | (quot - 1), port->membase + UBRLCR_OFFSET);
309}
310
311static const char *uart_clps711x_type(struct uart_port *port)
312{
313 return (port->type == PORT_CLPS711X) ? "CLPS711X" : NULL;
314}
315
316static void uart_clps711x_config_port(struct uart_port *port, int flags)
317{
318 if (flags & UART_CONFIG_TYPE)
319 port->type = PORT_CLPS711X;
320}
321
322static void uart_clps711x_nop_void(struct uart_port *port)
323{
324}
325
326static int uart_clps711x_nop_int(struct uart_port *port)
327{
328 return 0;
329}
330
331static const struct uart_ops uart_clps711x_ops = {
332 .tx_empty = uart_clps711x_tx_empty,
333 .set_mctrl = uart_clps711x_set_mctrl,
334 .get_mctrl = uart_clps711x_get_mctrl,
335 .stop_tx = uart_clps711x_stop_tx,
336 .start_tx = uart_clps711x_start_tx,
337 .stop_rx = uart_clps711x_nop_void,
338 .break_ctl = uart_clps711x_break_ctl,
339 .set_ldisc = uart_clps711x_set_ldisc,
340 .startup = uart_clps711x_startup,
341 .shutdown = uart_clps711x_shutdown,
342 .set_termios = uart_clps711x_set_termios,
343 .type = uart_clps711x_type,
344 .config_port = uart_clps711x_config_port,
345 .release_port = uart_clps711x_nop_void,
346 .request_port = uart_clps711x_nop_int,
347};
348
349#ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
350static void uart_clps711x_console_putchar(struct uart_port *port, unsigned char ch)
351{
352 struct clps711x_port *s = dev_get_drvdata(port->dev);
353 u32 sysflg = 0;
354
355 /* Wait for FIFO is not full */
356 do {
357 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
358 } while (sysflg & SYSFLG_UTXFF);
359
360 writew(ch, port->membase + UARTDR_OFFSET);
361}
362
363static void uart_clps711x_console_write(struct console *co, const char *c,
364 unsigned n)
365{
366 struct uart_port *port = clps711x_uart.state[co->index].uart_port;
367 struct clps711x_port *s = dev_get_drvdata(port->dev);
368 u32 sysflg = 0;
369
370 uart_console_write(port, c, n, uart_clps711x_console_putchar);
371
372 /* Wait for transmitter to become empty */
373 do {
374 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
375 } while (sysflg & SYSFLG_UBUSY);
376}
377
378static int uart_clps711x_console_setup(struct console *co, char *options)
379{
380 int baud = 38400, bits = 8, parity = 'n', flow = 'n';
381 int ret, index = co->index;
382 struct clps711x_port *s;
383 struct uart_port *port;
384 unsigned int quot;
385 u32 ubrlcr;
386
387 if (index < 0 || index >= UART_CLPS711X_NR)
388 return -EINVAL;
389
390 port = clps711x_uart.state[index].uart_port;
391 if (!port)
392 return -ENODEV;
393
394 s = dev_get_drvdata(port->dev);
395
396 if (!options) {
397 u32 syscon = 0;
398
399 regmap_read(s->syscon, SYSCON_OFFSET, &syscon);
400 if (syscon & SYSCON_UARTEN) {
401 ubrlcr = readl(port->membase + UBRLCR_OFFSET);
402
403 if (ubrlcr & UBRLCR_PRTEN) {
404 if (ubrlcr & UBRLCR_EVENPRT)
405 parity = 'e';
406 else
407 parity = 'o';
408 }
409
410 if ((ubrlcr & UBRLCR_WRDLEN_MASK) == UBRLCR_WRDLEN7)
411 bits = 7;
412
413 quot = ubrlcr & UBRLCR_BAUD_MASK;
414 baud = port->uartclk / (16 * (quot + 1));
415 }
416 } else
417 uart_parse_options(options, &baud, &parity, &bits, &flow);
418
419 ret = uart_set_options(port, co, baud, parity, bits, flow);
420 if (ret)
421 return ret;
422
423 return regmap_update_bits(s->syscon, SYSCON_OFFSET,
424 SYSCON_UARTEN, SYSCON_UARTEN);
425}
426
427static struct console clps711x_console = {
428 .name = UART_CLPS711X_DEVNAME,
429 .device = uart_console_device,
430 .write = uart_clps711x_console_write,
431 .setup = uart_clps711x_console_setup,
432 .flags = CON_PRINTBUFFER,
433 .index = -1,
434};
435#endif
436
437static int uart_clps711x_probe(struct platform_device *pdev)
438{
439 struct device_node *np = pdev->dev.of_node;
440 struct clps711x_port *s;
441 struct resource *res;
442 struct clk *uart_clk;
443 int irq, ret;
444
445 s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL);
446 if (!s)
447 return -ENOMEM;
448
449 uart_clk = devm_clk_get(&pdev->dev, NULL);
450 if (IS_ERR(uart_clk))
451 return PTR_ERR(uart_clk);
452
453 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
454 s->port.membase = devm_ioremap_resource(&pdev->dev, res);
455 if (IS_ERR(s->port.membase))
456 return PTR_ERR(s->port.membase);
457
458 irq = platform_get_irq(pdev, 0);
459 if (irq < 0)
460 return irq;
461 s->port.irq = irq;
462
463 s->rx_irq = platform_get_irq(pdev, 1);
464 if (s->rx_irq < 0)
465 return s->rx_irq;
466
467 s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon");
468 if (IS_ERR(s->syscon))
469 return PTR_ERR(s->syscon);
470
471 s->port.line = of_alias_get_id(np, "serial");
472 s->port.dev = &pdev->dev;
473 s->port.iotype = UPIO_MEM32;
474 s->port.mapbase = res->start;
475 s->port.type = PORT_CLPS711X;
476 s->port.fifosize = 16;
477 s->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_CLPS711X_CONSOLE);
478 s->port.flags = UPF_SKIP_TEST | UPF_FIXED_TYPE;
479 s->port.uartclk = clk_get_rate(uart_clk);
480 s->port.ops = &uart_clps711x_ops;
481
482 platform_set_drvdata(pdev, s);
483
484 s->gpios = mctrl_gpio_init_noauto(&pdev->dev, 0);
485 if (IS_ERR(s->gpios))
486 return PTR_ERR(s->gpios);
487
488 ret = uart_add_one_port(&clps711x_uart, &s->port);
489 if (ret)
490 return ret;
491
492 /* Disable port */
493 if (!uart_console(&s->port))
494 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
495
496 s->tx_enabled = 1;
497
498 ret = devm_request_irq(&pdev->dev, s->port.irq, uart_clps711x_int_tx, 0,
499 dev_name(&pdev->dev), &s->port);
500 if (ret) {
501 uart_remove_one_port(&clps711x_uart, &s->port);
502 return ret;
503 }
504
505 ret = devm_request_irq(&pdev->dev, s->rx_irq, uart_clps711x_int_rx, 0,
506 dev_name(&pdev->dev), &s->port);
507 if (ret)
508 uart_remove_one_port(&clps711x_uart, &s->port);
509
510 return ret;
511}
512
513static int uart_clps711x_remove(struct platform_device *pdev)
514{
515 struct clps711x_port *s = platform_get_drvdata(pdev);
516
517 return uart_remove_one_port(&clps711x_uart, &s->port);
518}
519
520static const struct of_device_id __maybe_unused clps711x_uart_dt_ids[] = {
521 { .compatible = "cirrus,ep7209-uart", },
522 { }
523};
524MODULE_DEVICE_TABLE(of, clps711x_uart_dt_ids);
525
526static struct platform_driver clps711x_uart_platform = {
527 .driver = {
528 .name = "clps711x-uart",
529 .of_match_table = of_match_ptr(clps711x_uart_dt_ids),
530 },
531 .probe = uart_clps711x_probe,
532 .remove = uart_clps711x_remove,
533};
534
535static int __init uart_clps711x_init(void)
536{
537 int ret;
538
539#ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
540 clps711x_uart.cons = &clps711x_console;
541 clps711x_console.data = &clps711x_uart;
542#endif
543
544 ret = uart_register_driver(&clps711x_uart);
545 if (ret)
546 return ret;
547
548 return platform_driver_register(&clps711x_uart_platform);
549}
550module_init(uart_clps711x_init);
551
552static void __exit uart_clps711x_exit(void)
553{
554 platform_driver_unregister(&clps711x_uart_platform);
555 uart_unregister_driver(&clps711x_uart);
556}
557module_exit(uart_clps711x_exit);
558
559MODULE_AUTHOR("Deep Blue Solutions Ltd");
560MODULE_DESCRIPTION("CLPS711X serial driver");
561MODULE_LICENSE("GPL");