Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2#include <linux/types.h>
3#include <linux/init.h>
4#include <linux/interrupt.h>
5#include <linux/mm.h>
6#include <linux/slab.h>
7#include <linux/spinlock.h>
8#include <linux/zorro.h>
9#include <linux/module.h>
10
11#include <asm/page.h>
12#include <asm/amigaints.h>
13#include <asm/amigahw.h>
14
15#include <scsi/scsi.h>
16#include <scsi/scsi_cmnd.h>
17#include <scsi/scsi_device.h>
18#include <scsi/scsi_eh.h>
19#include <scsi/scsi_tcq.h>
20#include "wd33c93.h"
21#include "gvp11.h"
22
23
24#define CHECK_WD33C93
25
26struct gvp11_hostdata {
27 struct WD33C93_hostdata wh;
28 struct gvp11_scsiregs *regs;
29 struct device *dev;
30};
31
32#define DMA_DIR(d) ((d == DATA_OUT_DIR) ? DMA_TO_DEVICE : DMA_FROM_DEVICE)
33#define TO_DMA_MASK(m) (~((unsigned long long)m & 0xffffffff))
34
35static irqreturn_t gvp11_intr(int irq, void *data)
36{
37 struct Scsi_Host *instance = data;
38 struct gvp11_hostdata *hdata = shost_priv(instance);
39 unsigned int status = hdata->regs->CNTR;
40 unsigned long flags;
41
42 if (!(status & GVP11_DMAC_INT_PENDING))
43 return IRQ_NONE;
44
45 spin_lock_irqsave(instance->host_lock, flags);
46 wd33c93_intr(instance);
47 spin_unlock_irqrestore(instance->host_lock, flags);
48 return IRQ_HANDLED;
49}
50
51static int gvp11_xfer_mask = 0;
52
53static int dma_setup(struct scsi_cmnd *cmd, int dir_in)
54{
55 struct scsi_pointer *scsi_pointer = WD33C93_scsi_pointer(cmd);
56 unsigned long len = scsi_pointer->this_residual;
57 struct Scsi_Host *instance = cmd->device->host;
58 struct gvp11_hostdata *hdata = shost_priv(instance);
59 struct WD33C93_hostdata *wh = &hdata->wh;
60 struct gvp11_scsiregs *regs = hdata->regs;
61 unsigned short cntr = GVP11_DMAC_INT_ENABLE;
62 dma_addr_t addr;
63 int bank_mask;
64 static int scsi_alloc_out_of_range = 0;
65
66 addr = dma_map_single(hdata->dev, scsi_pointer->ptr,
67 len, DMA_DIR(dir_in));
68 if (dma_mapping_error(hdata->dev, addr)) {
69 dev_warn(hdata->dev, "cannot map SCSI data block %p\n",
70 scsi_pointer->ptr);
71 return 1;
72 }
73 scsi_pointer->dma_handle = addr;
74
75 /* use bounce buffer if the physical address is bad */
76 if (addr & wh->dma_xfer_mask) {
77 /* drop useless mapping */
78 dma_unmap_single(hdata->dev, scsi_pointer->dma_handle,
79 scsi_pointer->this_residual,
80 DMA_DIR(dir_in));
81 scsi_pointer->dma_handle = (dma_addr_t) NULL;
82
83 wh->dma_bounce_len = (scsi_pointer->this_residual + 511) & ~0x1ff;
84
85 if (!scsi_alloc_out_of_range) {
86 wh->dma_bounce_buffer =
87 kmalloc(wh->dma_bounce_len, GFP_KERNEL);
88 wh->dma_buffer_pool = BUF_SCSI_ALLOCED;
89 }
90
91 if (scsi_alloc_out_of_range ||
92 !wh->dma_bounce_buffer) {
93 wh->dma_bounce_buffer =
94 amiga_chip_alloc(wh->dma_bounce_len,
95 "GVP II SCSI Bounce Buffer");
96
97 if (!wh->dma_bounce_buffer) {
98 wh->dma_bounce_len = 0;
99 return 1;
100 }
101
102 wh->dma_buffer_pool = BUF_CHIP_ALLOCED;
103 }
104
105 if (!dir_in) {
106 /* copy to bounce buffer for a write */
107 memcpy(wh->dma_bounce_buffer, scsi_pointer->ptr,
108 scsi_pointer->this_residual);
109 }
110
111 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED) {
112 /* will flush/invalidate cache for us */
113 addr = dma_map_single(hdata->dev,
114 wh->dma_bounce_buffer,
115 wh->dma_bounce_len,
116 DMA_DIR(dir_in));
117 /* can't map buffer; use PIO */
118 if (dma_mapping_error(hdata->dev, addr)) {
119 dev_warn(hdata->dev,
120 "cannot map bounce buffer %p\n",
121 wh->dma_bounce_buffer);
122 return 1;
123 }
124 }
125
126 if (addr & wh->dma_xfer_mask) {
127 /* drop useless mapping */
128 dma_unmap_single(hdata->dev, scsi_pointer->dma_handle,
129 scsi_pointer->this_residual,
130 DMA_DIR(dir_in));
131 /* fall back to Chip RAM if address out of range */
132 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED) {
133 kfree(wh->dma_bounce_buffer);
134 scsi_alloc_out_of_range = 1;
135 } else {
136 amiga_chip_free(wh->dma_bounce_buffer);
137 }
138
139 wh->dma_bounce_buffer =
140 amiga_chip_alloc(wh->dma_bounce_len,
141 "GVP II SCSI Bounce Buffer");
142
143 if (!wh->dma_bounce_buffer) {
144 wh->dma_bounce_len = 0;
145 return 1;
146 }
147
148 if (!dir_in) {
149 /* copy to bounce buffer for a write */
150 memcpy(wh->dma_bounce_buffer, scsi_pointer->ptr,
151 scsi_pointer->this_residual);
152 }
153 /* chip RAM can be mapped to phys. address directly */
154 addr = virt_to_phys(wh->dma_bounce_buffer);
155 /* no need to flush/invalidate cache */
156 wh->dma_buffer_pool = BUF_CHIP_ALLOCED;
157 }
158 /* finally, have OK mapping (punted for PIO else) */
159 scsi_pointer->dma_handle = addr;
160
161 }
162
163 /* setup dma direction */
164 if (!dir_in)
165 cntr |= GVP11_DMAC_DIR_WRITE;
166
167 wh->dma_dir = dir_in;
168 regs->CNTR = cntr;
169
170 /* setup DMA *physical* address */
171 regs->ACR = addr;
172
173 /* no more cache flush here - dma_map_single() takes care */
174
175 bank_mask = (~wh->dma_xfer_mask >> 18) & 0x01c0;
176 if (bank_mask)
177 regs->BANK = bank_mask & (addr >> 18);
178
179 /* start DMA */
180 regs->ST_DMA = 1;
181
182 /* return success */
183 return 0;
184}
185
186static void dma_stop(struct Scsi_Host *instance, struct scsi_cmnd *SCpnt,
187 int status)
188{
189 struct scsi_pointer *scsi_pointer = WD33C93_scsi_pointer(SCpnt);
190 struct gvp11_hostdata *hdata = shost_priv(instance);
191 struct WD33C93_hostdata *wh = &hdata->wh;
192 struct gvp11_scsiregs *regs = hdata->regs;
193
194 /* stop DMA */
195 regs->SP_DMA = 1;
196 /* remove write bit from CONTROL bits */
197 regs->CNTR = GVP11_DMAC_INT_ENABLE;
198
199 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED)
200 dma_unmap_single(hdata->dev, scsi_pointer->dma_handle,
201 scsi_pointer->this_residual,
202 DMA_DIR(wh->dma_dir));
203
204 /* copy from a bounce buffer, if necessary */
205 if (status && wh->dma_bounce_buffer) {
206 if (wh->dma_dir && SCpnt)
207 memcpy(scsi_pointer->ptr, wh->dma_bounce_buffer,
208 scsi_pointer->this_residual);
209
210 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED)
211 kfree(wh->dma_bounce_buffer);
212 else
213 amiga_chip_free(wh->dma_bounce_buffer);
214
215 wh->dma_bounce_buffer = NULL;
216 wh->dma_bounce_len = 0;
217 }
218}
219
220static const struct scsi_host_template gvp11_scsi_template = {
221 .module = THIS_MODULE,
222 .name = "GVP Series II SCSI",
223 .show_info = wd33c93_show_info,
224 .write_info = wd33c93_write_info,
225 .proc_name = "GVP11",
226 .queuecommand = wd33c93_queuecommand,
227 .eh_abort_handler = wd33c93_abort,
228 .eh_host_reset_handler = wd33c93_host_reset,
229 .can_queue = CAN_QUEUE,
230 .this_id = 7,
231 .sg_tablesize = SG_ALL,
232 .cmd_per_lun = CMD_PER_LUN,
233 .dma_boundary = PAGE_SIZE - 1,
234 .cmd_size = sizeof(struct scsi_pointer),
235};
236
237static int check_wd33c93(struct gvp11_scsiregs *regs)
238{
239#ifdef CHECK_WD33C93
240 volatile unsigned char *sasr_3393, *scmd_3393;
241 unsigned char save_sasr;
242 unsigned char q, qq;
243
244 /*
245 * These darn GVP boards are a problem - it can be tough to tell
246 * whether or not they include a SCSI controller. This is the
247 * ultimate Yet-Another-GVP-Detection-Hack in that it actually
248 * probes for a WD33c93 chip: If we find one, it's extremely
249 * likely that this card supports SCSI, regardless of Product_
250 * Code, Board_Size, etc.
251 */
252
253 /* Get pointers to the presumed register locations and save contents */
254
255 sasr_3393 = ®s->SASR;
256 scmd_3393 = ®s->SCMD;
257 save_sasr = *sasr_3393;
258
259 /* First test the AuxStatus Reg */
260
261 q = *sasr_3393; /* read it */
262 if (q & 0x08) /* bit 3 should always be clear */
263 return -ENODEV;
264 *sasr_3393 = WD_AUXILIARY_STATUS; /* setup indirect address */
265 if (*sasr_3393 == WD_AUXILIARY_STATUS) { /* shouldn't retain the write */
266 *sasr_3393 = save_sasr; /* Oops - restore this byte */
267 return -ENODEV;
268 }
269 if (*sasr_3393 != q) { /* should still read the same */
270 *sasr_3393 = save_sasr; /* Oops - restore this byte */
271 return -ENODEV;
272 }
273 if (*scmd_3393 != q) /* and so should the image at 0x1f */
274 return -ENODEV;
275
276 /*
277 * Ok, we probably have a wd33c93, but let's check a few other places
278 * for good measure. Make sure that this works for both 'A and 'B
279 * chip versions.
280 */
281
282 *sasr_3393 = WD_SCSI_STATUS;
283 q = *scmd_3393;
284 *sasr_3393 = WD_SCSI_STATUS;
285 *scmd_3393 = ~q;
286 *sasr_3393 = WD_SCSI_STATUS;
287 qq = *scmd_3393;
288 *sasr_3393 = WD_SCSI_STATUS;
289 *scmd_3393 = q;
290 if (qq != q) /* should be read only */
291 return -ENODEV;
292 *sasr_3393 = 0x1e; /* this register is unimplemented */
293 q = *scmd_3393;
294 *sasr_3393 = 0x1e;
295 *scmd_3393 = ~q;
296 *sasr_3393 = 0x1e;
297 qq = *scmd_3393;
298 *sasr_3393 = 0x1e;
299 *scmd_3393 = q;
300 if (qq != q || qq != 0xff) /* should be read only, all 1's */
301 return -ENODEV;
302 *sasr_3393 = WD_TIMEOUT_PERIOD;
303 q = *scmd_3393;
304 *sasr_3393 = WD_TIMEOUT_PERIOD;
305 *scmd_3393 = ~q;
306 *sasr_3393 = WD_TIMEOUT_PERIOD;
307 qq = *scmd_3393;
308 *sasr_3393 = WD_TIMEOUT_PERIOD;
309 *scmd_3393 = q;
310 if (qq != (~q & 0xff)) /* should be read/write */
311 return -ENODEV;
312#endif /* CHECK_WD33C93 */
313
314 return 0;
315}
316
317static int gvp11_probe(struct zorro_dev *z, const struct zorro_device_id *ent)
318{
319 struct Scsi_Host *instance;
320 unsigned long address;
321 int error;
322 unsigned int epc;
323 unsigned int default_dma_xfer_mask;
324 struct gvp11_hostdata *hdata;
325 struct gvp11_scsiregs *regs;
326 wd33c93_regs wdregs;
327
328 default_dma_xfer_mask = ent->driver_data;
329
330 if (dma_set_mask_and_coherent(&z->dev,
331 TO_DMA_MASK(default_dma_xfer_mask))) {
332 dev_warn(&z->dev, "cannot use DMA mask %llx\n",
333 TO_DMA_MASK(default_dma_xfer_mask));
334 return -ENODEV;
335 }
336
337 /*
338 * Rumors state that some GVP ram boards use the same product
339 * code as the SCSI controllers. Therefore if the board-size
340 * is not 64KB we assume it is a ram board and bail out.
341 */
342 if (zorro_resource_len(z) != 0x10000)
343 return -ENODEV;
344
345 address = z->resource.start;
346 if (!request_mem_region(address, 256, "wd33c93"))
347 return -EBUSY;
348
349 regs = ZTWO_VADDR(address);
350
351 error = check_wd33c93(regs);
352 if (error)
353 goto fail_check_or_alloc;
354
355 instance = scsi_host_alloc(&gvp11_scsi_template,
356 sizeof(struct gvp11_hostdata));
357 if (!instance) {
358 error = -ENOMEM;
359 goto fail_check_or_alloc;
360 }
361
362 instance->irq = IRQ_AMIGA_PORTS;
363 instance->unique_id = z->slotaddr;
364
365 regs->secret2 = 1;
366 regs->secret1 = 0;
367 regs->secret3 = 15;
368 while (regs->CNTR & GVP11_DMAC_BUSY)
369 ;
370 regs->CNTR = 0;
371 regs->BANK = 0;
372
373 wdregs.SASR = ®s->SASR;
374 wdregs.SCMD = ®s->SCMD;
375
376 hdata = shost_priv(instance);
377 if (gvp11_xfer_mask) {
378 hdata->wh.dma_xfer_mask = gvp11_xfer_mask;
379 if (dma_set_mask_and_coherent(&z->dev,
380 TO_DMA_MASK(gvp11_xfer_mask))) {
381 dev_warn(&z->dev, "cannot use DMA mask %llx\n",
382 TO_DMA_MASK(gvp11_xfer_mask));
383 error = -ENODEV;
384 goto fail_check_or_alloc;
385 }
386 } else
387 hdata->wh.dma_xfer_mask = default_dma_xfer_mask;
388
389 hdata->wh.no_sync = 0xff;
390 hdata->wh.fast = 0;
391 hdata->wh.dma_mode = CTRL_DMA;
392 hdata->regs = regs;
393
394 /*
395 * Check for 14MHz SCSI clock
396 */
397 epc = *(unsigned short *)(ZTWO_VADDR(address) + 0x8000);
398 wd33c93_init(instance, wdregs, dma_setup, dma_stop,
399 (epc & GVP_SCSICLKMASK) ? WD33C93_FS_8_10
400 : WD33C93_FS_12_15);
401
402 error = request_irq(IRQ_AMIGA_PORTS, gvp11_intr, IRQF_SHARED,
403 "GVP11 SCSI", instance);
404 if (error)
405 goto fail_irq;
406
407 regs->CNTR = GVP11_DMAC_INT_ENABLE;
408
409 error = scsi_add_host(instance, NULL);
410 if (error)
411 goto fail_host;
412
413 zorro_set_drvdata(z, instance);
414 scsi_scan_host(instance);
415 return 0;
416
417fail_host:
418 free_irq(IRQ_AMIGA_PORTS, instance);
419fail_irq:
420 scsi_host_put(instance);
421fail_check_or_alloc:
422 release_mem_region(address, 256);
423 return error;
424}
425
426static void gvp11_remove(struct zorro_dev *z)
427{
428 struct Scsi_Host *instance = zorro_get_drvdata(z);
429 struct gvp11_hostdata *hdata = shost_priv(instance);
430
431 hdata->regs->CNTR = 0;
432 scsi_remove_host(instance);
433 free_irq(IRQ_AMIGA_PORTS, instance);
434 scsi_host_put(instance);
435 release_mem_region(z->resource.start, 256);
436}
437
438 /*
439 * This should (hopefully) be the correct way to identify
440 * all the different GVP SCSI controllers (except for the
441 * SERIES I though).
442 */
443
444static struct zorro_device_id gvp11_zorro_tbl[] = {
445 { ZORRO_PROD_GVP_COMBO_030_R3_SCSI, ~0x00ffffff },
446 { ZORRO_PROD_GVP_SERIES_II, ~0x00ffffff },
447 { ZORRO_PROD_GVP_GFORCE_030_SCSI, ~0x01ffffff },
448 { ZORRO_PROD_GVP_A530_SCSI, ~0x01ffffff },
449 { ZORRO_PROD_GVP_COMBO_030_R4_SCSI, ~0x01ffffff },
450 { ZORRO_PROD_GVP_A1291, ~0x07ffffff },
451 { ZORRO_PROD_GVP_GFORCE_040_SCSI_1, ~0x07ffffff },
452 { 0 }
453};
454MODULE_DEVICE_TABLE(zorro, gvp11_zorro_tbl);
455
456static struct zorro_driver gvp11_driver = {
457 .name = "gvp11",
458 .id_table = gvp11_zorro_tbl,
459 .probe = gvp11_probe,
460 .remove = gvp11_remove,
461};
462
463static int __init gvp11_init(void)
464{
465 return zorro_register_driver(&gvp11_driver);
466}
467module_init(gvp11_init);
468
469static void __exit gvp11_exit(void)
470{
471 zorro_unregister_driver(&gvp11_driver);
472}
473module_exit(gvp11_exit);
474
475MODULE_DESCRIPTION("GVP Series II SCSI");
476MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0-only
2#include <linux/types.h>
3#include <linux/init.h>
4#include <linux/interrupt.h>
5#include <linux/mm.h>
6#include <linux/slab.h>
7#include <linux/spinlock.h>
8#include <linux/zorro.h>
9#include <linux/module.h>
10
11#include <asm/page.h>
12#include <asm/amigaints.h>
13#include <asm/amigahw.h>
14
15#include <scsi/scsi.h>
16#include <scsi/scsi_cmnd.h>
17#include <scsi/scsi_device.h>
18#include <scsi/scsi_eh.h>
19#include <scsi/scsi_tcq.h>
20#include "wd33c93.h"
21#include "gvp11.h"
22
23
24#define CHECK_WD33C93
25
26struct gvp11_hostdata {
27 struct WD33C93_hostdata wh;
28 struct gvp11_scsiregs *regs;
29 struct device *dev;
30};
31
32#define DMA_DIR(d) ((d == DATA_OUT_DIR) ? DMA_TO_DEVICE : DMA_FROM_DEVICE)
33#define TO_DMA_MASK(m) (~((unsigned long long)m & 0xffffffff))
34
35static irqreturn_t gvp11_intr(int irq, void *data)
36{
37 struct Scsi_Host *instance = data;
38 struct gvp11_hostdata *hdata = shost_priv(instance);
39 unsigned int status = hdata->regs->CNTR;
40 unsigned long flags;
41
42 if (!(status & GVP11_DMAC_INT_PENDING))
43 return IRQ_NONE;
44
45 spin_lock_irqsave(instance->host_lock, flags);
46 wd33c93_intr(instance);
47 spin_unlock_irqrestore(instance->host_lock, flags);
48 return IRQ_HANDLED;
49}
50
51static int gvp11_xfer_mask = 0;
52
53void gvp11_setup(char *str, int *ints)
54{
55 gvp11_xfer_mask = ints[1];
56}
57
58static int dma_setup(struct scsi_cmnd *cmd, int dir_in)
59{
60 struct scsi_pointer *scsi_pointer = WD33C93_scsi_pointer(cmd);
61 unsigned long len = scsi_pointer->this_residual;
62 struct Scsi_Host *instance = cmd->device->host;
63 struct gvp11_hostdata *hdata = shost_priv(instance);
64 struct WD33C93_hostdata *wh = &hdata->wh;
65 struct gvp11_scsiregs *regs = hdata->regs;
66 unsigned short cntr = GVP11_DMAC_INT_ENABLE;
67 dma_addr_t addr;
68 int bank_mask;
69 static int scsi_alloc_out_of_range = 0;
70
71 addr = dma_map_single(hdata->dev, scsi_pointer->ptr,
72 len, DMA_DIR(dir_in));
73 if (dma_mapping_error(hdata->dev, addr)) {
74 dev_warn(hdata->dev, "cannot map SCSI data block %p\n",
75 scsi_pointer->ptr);
76 return 1;
77 }
78 scsi_pointer->dma_handle = addr;
79
80 /* use bounce buffer if the physical address is bad */
81 if (addr & wh->dma_xfer_mask) {
82 /* drop useless mapping */
83 dma_unmap_single(hdata->dev, scsi_pointer->dma_handle,
84 scsi_pointer->this_residual,
85 DMA_DIR(dir_in));
86 scsi_pointer->dma_handle = (dma_addr_t) NULL;
87
88 wh->dma_bounce_len = (scsi_pointer->this_residual + 511) & ~0x1ff;
89
90 if (!scsi_alloc_out_of_range) {
91 wh->dma_bounce_buffer =
92 kmalloc(wh->dma_bounce_len, GFP_KERNEL);
93 wh->dma_buffer_pool = BUF_SCSI_ALLOCED;
94 }
95
96 if (scsi_alloc_out_of_range ||
97 !wh->dma_bounce_buffer) {
98 wh->dma_bounce_buffer =
99 amiga_chip_alloc(wh->dma_bounce_len,
100 "GVP II SCSI Bounce Buffer");
101
102 if (!wh->dma_bounce_buffer) {
103 wh->dma_bounce_len = 0;
104 return 1;
105 }
106
107 wh->dma_buffer_pool = BUF_CHIP_ALLOCED;
108 }
109
110 if (!dir_in) {
111 /* copy to bounce buffer for a write */
112 memcpy(wh->dma_bounce_buffer, scsi_pointer->ptr,
113 scsi_pointer->this_residual);
114 }
115
116 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED) {
117 /* will flush/invalidate cache for us */
118 addr = dma_map_single(hdata->dev,
119 wh->dma_bounce_buffer,
120 wh->dma_bounce_len,
121 DMA_DIR(dir_in));
122 /* can't map buffer; use PIO */
123 if (dma_mapping_error(hdata->dev, addr)) {
124 dev_warn(hdata->dev,
125 "cannot map bounce buffer %p\n",
126 wh->dma_bounce_buffer);
127 return 1;
128 }
129 }
130
131 if (addr & wh->dma_xfer_mask) {
132 /* drop useless mapping */
133 dma_unmap_single(hdata->dev, scsi_pointer->dma_handle,
134 scsi_pointer->this_residual,
135 DMA_DIR(dir_in));
136 /* fall back to Chip RAM if address out of range */
137 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED) {
138 kfree(wh->dma_bounce_buffer);
139 scsi_alloc_out_of_range = 1;
140 } else {
141 amiga_chip_free(wh->dma_bounce_buffer);
142 }
143
144 wh->dma_bounce_buffer =
145 amiga_chip_alloc(wh->dma_bounce_len,
146 "GVP II SCSI Bounce Buffer");
147
148 if (!wh->dma_bounce_buffer) {
149 wh->dma_bounce_len = 0;
150 return 1;
151 }
152
153 if (!dir_in) {
154 /* copy to bounce buffer for a write */
155 memcpy(wh->dma_bounce_buffer, scsi_pointer->ptr,
156 scsi_pointer->this_residual);
157 }
158 /* chip RAM can be mapped to phys. address directly */
159 addr = virt_to_phys(wh->dma_bounce_buffer);
160 /* no need to flush/invalidate cache */
161 wh->dma_buffer_pool = BUF_CHIP_ALLOCED;
162 }
163 /* finally, have OK mapping (punted for PIO else) */
164 scsi_pointer->dma_handle = addr;
165
166 }
167
168 /* setup dma direction */
169 if (!dir_in)
170 cntr |= GVP11_DMAC_DIR_WRITE;
171
172 wh->dma_dir = dir_in;
173 regs->CNTR = cntr;
174
175 /* setup DMA *physical* address */
176 regs->ACR = addr;
177
178 /* no more cache flush here - dma_map_single() takes care */
179
180 bank_mask = (~wh->dma_xfer_mask >> 18) & 0x01c0;
181 if (bank_mask)
182 regs->BANK = bank_mask & (addr >> 18);
183
184 /* start DMA */
185 regs->ST_DMA = 1;
186
187 /* return success */
188 return 0;
189}
190
191static void dma_stop(struct Scsi_Host *instance, struct scsi_cmnd *SCpnt,
192 int status)
193{
194 struct scsi_pointer *scsi_pointer = WD33C93_scsi_pointer(SCpnt);
195 struct gvp11_hostdata *hdata = shost_priv(instance);
196 struct WD33C93_hostdata *wh = &hdata->wh;
197 struct gvp11_scsiregs *regs = hdata->regs;
198
199 /* stop DMA */
200 regs->SP_DMA = 1;
201 /* remove write bit from CONTROL bits */
202 regs->CNTR = GVP11_DMAC_INT_ENABLE;
203
204 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED)
205 dma_unmap_single(hdata->dev, scsi_pointer->dma_handle,
206 scsi_pointer->this_residual,
207 DMA_DIR(wh->dma_dir));
208
209 /* copy from a bounce buffer, if necessary */
210 if (status && wh->dma_bounce_buffer) {
211 if (wh->dma_dir && SCpnt)
212 memcpy(scsi_pointer->ptr, wh->dma_bounce_buffer,
213 scsi_pointer->this_residual);
214
215 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED)
216 kfree(wh->dma_bounce_buffer);
217 else
218 amiga_chip_free(wh->dma_bounce_buffer);
219
220 wh->dma_bounce_buffer = NULL;
221 wh->dma_bounce_len = 0;
222 }
223}
224
225static struct scsi_host_template gvp11_scsi_template = {
226 .module = THIS_MODULE,
227 .name = "GVP Series II SCSI",
228 .show_info = wd33c93_show_info,
229 .write_info = wd33c93_write_info,
230 .proc_name = "GVP11",
231 .queuecommand = wd33c93_queuecommand,
232 .eh_abort_handler = wd33c93_abort,
233 .eh_host_reset_handler = wd33c93_host_reset,
234 .can_queue = CAN_QUEUE,
235 .this_id = 7,
236 .sg_tablesize = SG_ALL,
237 .cmd_per_lun = CMD_PER_LUN,
238 .dma_boundary = PAGE_SIZE - 1,
239 .cmd_size = sizeof(struct scsi_pointer),
240};
241
242static int check_wd33c93(struct gvp11_scsiregs *regs)
243{
244#ifdef CHECK_WD33C93
245 volatile unsigned char *sasr_3393, *scmd_3393;
246 unsigned char save_sasr;
247 unsigned char q, qq;
248
249 /*
250 * These darn GVP boards are a problem - it can be tough to tell
251 * whether or not they include a SCSI controller. This is the
252 * ultimate Yet-Another-GVP-Detection-Hack in that it actually
253 * probes for a WD33c93 chip: If we find one, it's extremely
254 * likely that this card supports SCSI, regardless of Product_
255 * Code, Board_Size, etc.
256 */
257
258 /* Get pointers to the presumed register locations and save contents */
259
260 sasr_3393 = ®s->SASR;
261 scmd_3393 = ®s->SCMD;
262 save_sasr = *sasr_3393;
263
264 /* First test the AuxStatus Reg */
265
266 q = *sasr_3393; /* read it */
267 if (q & 0x08) /* bit 3 should always be clear */
268 return -ENODEV;
269 *sasr_3393 = WD_AUXILIARY_STATUS; /* setup indirect address */
270 if (*sasr_3393 == WD_AUXILIARY_STATUS) { /* shouldn't retain the write */
271 *sasr_3393 = save_sasr; /* Oops - restore this byte */
272 return -ENODEV;
273 }
274 if (*sasr_3393 != q) { /* should still read the same */
275 *sasr_3393 = save_sasr; /* Oops - restore this byte */
276 return -ENODEV;
277 }
278 if (*scmd_3393 != q) /* and so should the image at 0x1f */
279 return -ENODEV;
280
281 /*
282 * Ok, we probably have a wd33c93, but let's check a few other places
283 * for good measure. Make sure that this works for both 'A and 'B
284 * chip versions.
285 */
286
287 *sasr_3393 = WD_SCSI_STATUS;
288 q = *scmd_3393;
289 *sasr_3393 = WD_SCSI_STATUS;
290 *scmd_3393 = ~q;
291 *sasr_3393 = WD_SCSI_STATUS;
292 qq = *scmd_3393;
293 *sasr_3393 = WD_SCSI_STATUS;
294 *scmd_3393 = q;
295 if (qq != q) /* should be read only */
296 return -ENODEV;
297 *sasr_3393 = 0x1e; /* this register is unimplemented */
298 q = *scmd_3393;
299 *sasr_3393 = 0x1e;
300 *scmd_3393 = ~q;
301 *sasr_3393 = 0x1e;
302 qq = *scmd_3393;
303 *sasr_3393 = 0x1e;
304 *scmd_3393 = q;
305 if (qq != q || qq != 0xff) /* should be read only, all 1's */
306 return -ENODEV;
307 *sasr_3393 = WD_TIMEOUT_PERIOD;
308 q = *scmd_3393;
309 *sasr_3393 = WD_TIMEOUT_PERIOD;
310 *scmd_3393 = ~q;
311 *sasr_3393 = WD_TIMEOUT_PERIOD;
312 qq = *scmd_3393;
313 *sasr_3393 = WD_TIMEOUT_PERIOD;
314 *scmd_3393 = q;
315 if (qq != (~q & 0xff)) /* should be read/write */
316 return -ENODEV;
317#endif /* CHECK_WD33C93 */
318
319 return 0;
320}
321
322static int gvp11_probe(struct zorro_dev *z, const struct zorro_device_id *ent)
323{
324 struct Scsi_Host *instance;
325 unsigned long address;
326 int error;
327 unsigned int epc;
328 unsigned int default_dma_xfer_mask;
329 struct gvp11_hostdata *hdata;
330 struct gvp11_scsiregs *regs;
331 wd33c93_regs wdregs;
332
333 default_dma_xfer_mask = ent->driver_data;
334
335 if (dma_set_mask_and_coherent(&z->dev,
336 TO_DMA_MASK(default_dma_xfer_mask))) {
337 dev_warn(&z->dev, "cannot use DMA mask %llx\n",
338 TO_DMA_MASK(default_dma_xfer_mask));
339 return -ENODEV;
340 }
341
342 /*
343 * Rumors state that some GVP ram boards use the same product
344 * code as the SCSI controllers. Therefore if the board-size
345 * is not 64KB we assume it is a ram board and bail out.
346 */
347 if (zorro_resource_len(z) != 0x10000)
348 return -ENODEV;
349
350 address = z->resource.start;
351 if (!request_mem_region(address, 256, "wd33c93"))
352 return -EBUSY;
353
354 regs = ZTWO_VADDR(address);
355
356 error = check_wd33c93(regs);
357 if (error)
358 goto fail_check_or_alloc;
359
360 instance = scsi_host_alloc(&gvp11_scsi_template,
361 sizeof(struct gvp11_hostdata));
362 if (!instance) {
363 error = -ENOMEM;
364 goto fail_check_or_alloc;
365 }
366
367 instance->irq = IRQ_AMIGA_PORTS;
368 instance->unique_id = z->slotaddr;
369
370 regs->secret2 = 1;
371 regs->secret1 = 0;
372 regs->secret3 = 15;
373 while (regs->CNTR & GVP11_DMAC_BUSY)
374 ;
375 regs->CNTR = 0;
376 regs->BANK = 0;
377
378 wdregs.SASR = ®s->SASR;
379 wdregs.SCMD = ®s->SCMD;
380
381 hdata = shost_priv(instance);
382 if (gvp11_xfer_mask) {
383 hdata->wh.dma_xfer_mask = gvp11_xfer_mask;
384 if (dma_set_mask_and_coherent(&z->dev,
385 TO_DMA_MASK(gvp11_xfer_mask))) {
386 dev_warn(&z->dev, "cannot use DMA mask %llx\n",
387 TO_DMA_MASK(gvp11_xfer_mask));
388 error = -ENODEV;
389 goto fail_check_or_alloc;
390 }
391 } else
392 hdata->wh.dma_xfer_mask = default_dma_xfer_mask;
393
394 hdata->wh.no_sync = 0xff;
395 hdata->wh.fast = 0;
396 hdata->wh.dma_mode = CTRL_DMA;
397 hdata->regs = regs;
398
399 /*
400 * Check for 14MHz SCSI clock
401 */
402 epc = *(unsigned short *)(ZTWO_VADDR(address) + 0x8000);
403 wd33c93_init(instance, wdregs, dma_setup, dma_stop,
404 (epc & GVP_SCSICLKMASK) ? WD33C93_FS_8_10
405 : WD33C93_FS_12_15);
406
407 error = request_irq(IRQ_AMIGA_PORTS, gvp11_intr, IRQF_SHARED,
408 "GVP11 SCSI", instance);
409 if (error)
410 goto fail_irq;
411
412 regs->CNTR = GVP11_DMAC_INT_ENABLE;
413
414 error = scsi_add_host(instance, NULL);
415 if (error)
416 goto fail_host;
417
418 zorro_set_drvdata(z, instance);
419 scsi_scan_host(instance);
420 return 0;
421
422fail_host:
423 free_irq(IRQ_AMIGA_PORTS, instance);
424fail_irq:
425 scsi_host_put(instance);
426fail_check_or_alloc:
427 release_mem_region(address, 256);
428 return error;
429}
430
431static void gvp11_remove(struct zorro_dev *z)
432{
433 struct Scsi_Host *instance = zorro_get_drvdata(z);
434 struct gvp11_hostdata *hdata = shost_priv(instance);
435
436 hdata->regs->CNTR = 0;
437 scsi_remove_host(instance);
438 free_irq(IRQ_AMIGA_PORTS, instance);
439 scsi_host_put(instance);
440 release_mem_region(z->resource.start, 256);
441}
442
443 /*
444 * This should (hopefully) be the correct way to identify
445 * all the different GVP SCSI controllers (except for the
446 * SERIES I though).
447 */
448
449static struct zorro_device_id gvp11_zorro_tbl[] = {
450 { ZORRO_PROD_GVP_COMBO_030_R3_SCSI, ~0x00ffffff },
451 { ZORRO_PROD_GVP_SERIES_II, ~0x00ffffff },
452 { ZORRO_PROD_GVP_GFORCE_030_SCSI, ~0x01ffffff },
453 { ZORRO_PROD_GVP_A530_SCSI, ~0x01ffffff },
454 { ZORRO_PROD_GVP_COMBO_030_R4_SCSI, ~0x01ffffff },
455 { ZORRO_PROD_GVP_A1291, ~0x07ffffff },
456 { ZORRO_PROD_GVP_GFORCE_040_SCSI_1, ~0x07ffffff },
457 { 0 }
458};
459MODULE_DEVICE_TABLE(zorro, gvp11_zorro_tbl);
460
461static struct zorro_driver gvp11_driver = {
462 .name = "gvp11",
463 .id_table = gvp11_zorro_tbl,
464 .probe = gvp11_probe,
465 .remove = gvp11_remove,
466};
467
468static int __init gvp11_init(void)
469{
470 return zorro_register_driver(&gvp11_driver);
471}
472module_init(gvp11_init);
473
474static void __exit gvp11_exit(void)
475{
476 zorro_unregister_driver(&gvp11_driver);
477}
478module_exit(gvp11_exit);
479
480MODULE_DESCRIPTION("GVP Series II SCSI");
481MODULE_LICENSE("GPL");