Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# USB Network devices configuration
4#
5comment "Host-side USB support is needed for USB Network Adapter support"
6 depends on !USB && NET
7
8menuconfig USB_NET_DRIVERS
9 tristate "USB Network Adapters"
10 default USB if USB
11 depends on USB && NET
12
13if USB_NET_DRIVERS
14
15config USB_CATC
16 tristate "USB CATC NetMate-based Ethernet device support"
17 select CRC32
18 help
19 Say Y if you want to use one of the following 10Mbps USB Ethernet
20 device based on the EL1210A chip. Supported devices are:
21 Belkin F5U011
22 Belkin F5U111
23 CATC NetMate
24 CATC NetMate II
25 smartBridges smartNIC
26
27 This driver makes the adapter appear as a normal Ethernet interface,
28 typically on eth0, if it is the only ethernet device, or perhaps on
29 eth1, if you have a PCI or ISA ethernet card installed.
30
31 To compile this driver as a module, choose M here: the
32 module will be called catc.
33
34config USB_KAWETH
35 tristate "USB KLSI KL5USB101-based ethernet device support"
36 help
37 Say Y here if you want to use one of the following 10Mbps only
38 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
39 3Com 3C19250
40 ADS USB-10BT
41 ATEN USB Ethernet
42 ASANTE USB To Ethernet Adapter
43 AOX Endpoints USB Ethernet
44 Correga K.K.
45 D-Link DSB-650C and DU-E10
46 Entrega / Portgear E45
47 I-O DATA USB-ET/T
48 Jaton USB Ethernet Device Adapter
49 Kingston Technology USB Ethernet Adapter
50 Linksys USB10T
51 Mobility USB-Ethernet Adapter
52 NetGear EA-101
53 Peracom Enet and Enet2
54 Portsmith Express Ethernet Adapter
55 Shark Pocket Adapter
56 SMC 2202USB
57 Sony Vaio port extender
58
59 This driver is likely to work with most 10Mbps only USB Ethernet
60 adapters, including some "no brand" devices. It does NOT work on
61 SmartBridges smartNIC or on Belkin F5U111 devices - you should use
62 the CATC NetMate driver for those. If you are not sure which one
63 you need, select both, and the correct one should be selected for
64 you.
65
66 This driver makes the adapter appear as a normal Ethernet interface,
67 typically on eth0, if it is the only ethernet device, or perhaps on
68 eth1, if you have a PCI or ISA ethernet card installed.
69
70 To compile this driver as a module, choose M here: the
71 module will be called kaweth.
72
73config USB_PEGASUS
74 tristate "USB Pegasus/Pegasus-II based ethernet device support"
75 select MII
76 help
77 Say Y here if you know you have Pegasus or Pegasus-II based adapter.
78 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
79 complete list of supported devices.
80
81 If your particular adapter is not in the list and you are _sure_ it
82 is Pegasus or Pegasus II based then send me
83 <petkan@users.sourceforge.net> vendor and device IDs.
84
85 To compile this driver as a module, choose M here: the
86 module will be called pegasus.
87
88config USB_RTL8150
89 tristate "USB RTL8150 based ethernet device support"
90 select MII
91 help
92 Say Y here if you have RTL8150 based usb-ethernet adapter.
93 Send me <petkan@users.sourceforge.net> any comments you may have.
94 You can also check for updates at <http://pegasus2.sourceforge.net/>.
95
96 To compile this driver as a module, choose M here: the
97 module will be called rtl8150.
98
99config USB_RTL8152
100 tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters"
101 select MII
102 select CRC32
103 select CRYPTO
104 select CRYPTO_HASH
105 select CRYPTO_SHA256
106 help
107 This option adds support for Realtek RTL8152 based USB 2.0
108 10/100 Ethernet adapters and RTL8153 based USB 3.0 10/100/1000
109 Ethernet adapters.
110
111 To compile this driver as a module, choose M here: the
112 module will be called r8152.
113
114config USB_LAN78XX
115 tristate "Microchip LAN78XX Based USB Ethernet Adapters"
116 select MII
117 select PHYLIB
118 select MICROCHIP_PHY
119 select FIXED_PHY
120 select CRC32
121 help
122 This option adds support for Microchip LAN78XX based USB 2
123 & USB 3 10/100/1000 Ethernet adapters.
124 LAN7800 : USB 3 to 10/100/1000 Ethernet adapter
125 LAN7850 : USB 2 to 10/100/1000 Ethernet adapter
126 LAN7801 : USB 3 to 10/100/1000 Ethernet adapter (MAC only)
127
128 Proper PHY driver is required for LAN7801.
129
130 To compile this driver as a module, choose M here: the
131 module will be called lan78xx.
132
133config USB_USBNET
134 tristate "Multi-purpose USB Networking Framework"
135 select MII
136 help
137 This driver supports several kinds of network links over USB,
138 with "minidrivers" built around a common network driver core
139 that supports deep queues for efficient transfers. (This gives
140 better performance with small packets and at high speeds).
141
142 The USB host runs "usbnet", and the other end of the link might be:
143
144 - Another USB host, when using USB "network" or "data transfer"
145 cables. These are often used to network laptops to PCs, like
146 "Laplink" parallel cables or some motherboards. These rely
147 on specialized chips from many suppliers.
148
149 - An intelligent USB gadget, perhaps embedding a Linux system.
150 These include PDAs running Linux (iPaq, Yopy, Zaurus, and
151 others), and devices that interoperate using the standard
152 CDC-Ethernet specification (including many cable modems).
153
154 - Network adapter hardware (like those for 10/100 Ethernet) which
155 uses this driver framework.
156
157 The link will appear with a name like "usb0", when the link is
158 a two-node link, or "eth0" for most CDC-Ethernet devices. Those
159 two-node links are most easily managed with Ethernet Bridging
160 (CONFIG_BRIDGE) instead of routing.
161
162 For more information see <http://www.linux-usb.org/usbnet/>.
163
164 To compile this driver as a module, choose M here: the
165 module will be called usbnet.
166
167config USB_NET_AX8817X
168 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
169 depends on USB_USBNET
170 select CRC32
171 select PHYLINK
172 select AX88796B_PHY
173 imply NET_SELFTESTS
174 default y
175 help
176 This option adds support for ASIX AX88xxx based USB 2.0
177 10/100 Ethernet adapters.
178
179 This driver should work with at least the following devices:
180 * Aten UC210T
181 * ASIX AX88172
182 * Billionton Systems, USB2AR
183 * Billionton Systems, GUSB2AM-1G-B
184 * Buffalo LUA-U2-KTX
185 * Corega FEther USB2-TX
186 * D-Link DUB-E100
187 * Hawking UF200
188 * Linksys USB200M
189 * Netgear FA120
190 * Sitecom LN-029
191 * Sitecom LN-028
192 * Intellinet USB 2.0 Ethernet
193 * ST Lab USB 2.0 Ethernet
194 * TrendNet TU2-ET100
195
196 This driver creates an interface named "ethX", where X depends on
197 what other networking devices you have in use.
198
199config USB_NET_AX88179_178A
200 tristate "ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet"
201 depends on USB_USBNET
202 select CRC32
203 select PHYLIB
204 default y
205 help
206 This option adds support for ASIX AX88179 based USB 3.0/2.0
207 to Gigabit Ethernet adapters.
208
209 This driver should work with at least the following devices:
210 * ASIX AX88179
211 * ASIX AX88178A
212 * Sitcomm LN-032
213
214 This driver creates an interface named "ethX", where X depends on
215 what other networking devices you have in use.
216
217config USB_NET_CDCETHER
218 tristate "CDC Ethernet support (smart devices such as cable modems)"
219 depends on USB_USBNET
220 default y
221 help
222 This option supports devices conforming to the Communication Device
223 Class (CDC) Ethernet Control Model, a specification that's easy to
224 implement in device firmware. The CDC specifications are available
225 from <http://www.usb.org/>.
226
227 CDC Ethernet is an implementation option for DOCSIS cable modems
228 that support USB connectivity, used for non-Microsoft USB hosts.
229 The Linux-USB CDC Ethernet Gadget driver is an open implementation.
230 This driver should work with at least the following devices:
231
232 * Dell Wireless 5530 HSPA
233 * Ericsson PipeRider (all variants)
234 * Ericsson Mobile Broadband Module (all variants)
235 * Motorola (DM100 and SB4100)
236 * Broadcom Cable Modem (reference design)
237 * Toshiba (PCX1100U and F3507g/F3607gw)
238 * ...
239
240 This driver creates an interface named "ethX", where X depends on
241 what other networking devices you have in use. However, if the
242 IEEE 802 "local assignment" bit is set in the address, a "usbX"
243 name is used instead.
244
245config USB_NET_CDC_EEM
246 tristate "CDC EEM support"
247 depends on USB_USBNET
248 help
249 This option supports devices conforming to the Communication Device
250 Class (CDC) Ethernet Emulation Model, a specification that's easy to
251 implement in device firmware. The CDC EEM specifications are available
252 from <http://www.usb.org/>.
253
254 This driver creates an interface named "ethX", where X depends on
255 what other networking devices you have in use. However, if the
256 IEEE 802 "local assignment" bit is set in the address, a "usbX"
257 name is used instead.
258
259config USB_NET_CDC_NCM
260 tristate "CDC NCM support"
261 depends on USB_USBNET
262 select USB_NET_CDCETHER
263 default y
264 help
265 This driver provides support for CDC NCM (Network Control Model
266 Device USB Class Specification). The CDC NCM specification is
267 available from <http://www.usb.org/>.
268
269 Say "y" to link the driver statically, or "m" to build a
270 dynamically linked module.
271
272 This driver should work with at least the following devices:
273 * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
274 * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
275 * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
276 * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
277 * Ericsson F5521gw Mobile Broadband Module
278
279config USB_NET_HUAWEI_CDC_NCM
280 tristate "Huawei NCM embedded AT channel support"
281 depends on USB_USBNET
282 select USB_WDM
283 select USB_NET_CDC_NCM
284 help
285 This driver supports huawei-style NCM devices, that use NCM as a
286 transport for other protocols, usually an embedded AT channel.
287 Good examples are:
288 * Huawei E3131
289 * Huawei E3251
290
291 To compile this driver as a module, choose M here: the module will be
292 called huawei_cdc_ncm.ko.
293
294config USB_NET_CDC_MBIM
295 tristate "CDC MBIM support"
296 depends on USB_USBNET
297 select USB_WDM
298 select USB_NET_CDC_NCM
299 help
300 This driver provides support for CDC MBIM (Mobile Broadband
301 Interface Model) devices. The CDC MBIM specification is
302 available from <http://www.usb.org/>.
303
304 MBIM devices require configuration using the management
305 protocol defined by the MBIM specification. This driver
306 provides unfiltered access to the MBIM control channel
307 through the associated /dev/cdc-wdmx character device.
308
309 To compile this driver as a module, choose M here: the
310 module will be called cdc_mbim.
311
312config USB_NET_DM9601
313 tristate "Davicom DM96xx based USB 10/100 ethernet devices"
314 depends on USB_USBNET
315 select CRC32
316 help
317 This option adds support for Davicom DM9601/DM9620/DM9621A
318 based USB 10/100 Ethernet adapters.
319
320config USB_NET_SR9700
321 tristate "CoreChip-sz SR9700 based USB 1.1 10/100 ethernet devices"
322 depends on USB_USBNET
323 select CRC32
324 help
325 This option adds support for CoreChip-sz SR9700 based USB 1.1
326 10/100 Ethernet adapters.
327
328config USB_NET_SR9800
329 tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices"
330 depends on USB_USBNET
331 select CRC32
332 help
333 Say Y if you want to use one of the following 100Mbps USB Ethernet
334 device based on the CoreChip-sz SR9800 chip.
335
336 This driver makes the adapter appear as a normal Ethernet interface,
337 typically on eth0, if it is the only ethernet device, or perhaps on
338 eth1, if you have a PCI or ISA ethernet card installed.
339
340 To compile this driver as a module, choose M here: the
341 module will be called sr9800.
342
343config USB_NET_SMSC75XX
344 tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
345 depends on USB_USBNET
346 select BITREVERSE
347 select CRC16
348 select CRC32
349 help
350 This option adds support for SMSC LAN75XX based USB 2.0
351 Gigabit Ethernet adapters.
352
353config USB_NET_SMSC95XX
354 tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
355 depends on USB_USBNET
356 select PHYLIB
357 select SMSC_PHY
358 select BITREVERSE
359 select CRC16
360 select CRC32
361 imply NET_SELFTESTS
362 help
363 This option adds support for SMSC LAN95XX based USB 2.0
364 10/100 Ethernet adapters.
365
366config USB_NET_GL620A
367 tristate "GeneSys GL620USB-A based cables"
368 depends on USB_USBNET
369 help
370 Choose this option if you're using a host-to-host cable,
371 or PC2PC motherboard, with this chip.
372
373 Note that the half-duplex "GL620USB" is not supported.
374
375config USB_NET_NET1080
376 tristate "NetChip 1080 based cables (Laplink, ...)"
377 default y
378 depends on USB_USBNET
379 help
380 Choose this option if you're using a host-to-host cable based
381 on this design: one NetChip 1080 chip and supporting logic,
382 optionally with LEDs that indicate traffic
383
384config USB_NET_PLUSB
385 tristate "Prolific PL-2301/2302/25A1/27A1 based cables"
386 # if the handshake/init/reset problems, from original 'plusb',
387 # are ever resolved ... then remove "experimental"
388 depends on USB_USBNET
389 help
390 Choose this option if you're using a host-to-host cable
391 with one of these chips.
392
393config USB_NET_MCS7830
394 tristate "MosChip MCS7830 based Ethernet adapters"
395 depends on USB_USBNET
396 help
397 Choose this option if you're using a 10/100 Ethernet USB2
398 adapter based on the MosChip 7830 controller. This includes
399 adapters marketed under the DeLOCK brand.
400
401config USB_NET_RNDIS_HOST
402 tristate "Host for RNDIS and ActiveSync devices"
403 depends on USB_USBNET
404 select USB_NET_CDCETHER
405 help
406 This option enables hosting "Remote NDIS" USB networking links,
407 as encouraged by Microsoft (instead of CDC Ethernet!) for use in
408 various devices that may only support this protocol. A variant
409 of this protocol (with even less public documentation) seems to
410 be at the root of Microsoft's "ActiveSync" too.
411
412 Avoid using this protocol unless you have no better options.
413 The protocol specification is incomplete, and is controlled by
414 (and for) Microsoft; it isn't an "Open" ecosystem or market.
415
416config USB_NET_CDC_SUBSET_ENABLE
417 tristate
418 depends on USB_NET_CDC_SUBSET
419
420config USB_NET_CDC_SUBSET
421 tristate "Simple USB Network Links (CDC Ethernet subset)"
422 depends on USB_USBNET
423 default y
424 help
425 This driver module supports USB network devices that can work
426 without any device-specific information. Select it if you have
427 one of these drivers.
428
429 Note that while many USB host-to-host cables can work in this mode,
430 that may mean not being able to talk to Win32 systems or more
431 commonly not being able to handle certain events (like replugging
432 the host on the other end) very well. Also, these devices will
433 not generally have permanently assigned Ethernet addresses.
434
435config USB_ALI_M5632
436 bool "ALi M5632 based 'USB 2.0 Data Link' cables"
437 depends on USB_NET_CDC_SUBSET
438 select USB_NET_CDC_SUBSET_ENABLE
439 help
440 Choose this option if you're using a host-to-host cable
441 based on this design, which supports USB 2.0 high speed.
442
443config USB_AN2720
444 bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
445 depends on USB_NET_CDC_SUBSET
446 select USB_NET_CDC_SUBSET_ENABLE
447 help
448 Choose this option if you're using a host-to-host cable
449 based on this design. Note that AnchorChips is now a
450 Cypress brand.
451
452config USB_BELKIN
453 bool "eTEK based host-to-host cables (Advance, Belkin, ...)"
454 depends on USB_NET_CDC_SUBSET
455 select USB_NET_CDC_SUBSET_ENABLE
456 default y
457 help
458 Choose this option if you're using a host-to-host cable
459 based on this design: two NetChip 2890 chips and an Atmel
460 microcontroller, with LEDs that indicate traffic.
461
462config USB_ARMLINUX
463 bool "Embedded ARM Linux links (iPaq, ...)"
464 depends on USB_NET_CDC_SUBSET
465 select USB_NET_CDC_SUBSET_ENABLE
466 default y
467 help
468 Choose this option to support the "usb-eth" networking driver
469 used by most of the ARM Linux community with device controllers
470 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
471 in some PXA versions of the "blob" boot loader.
472
473 Linux-based "Gumstix" PXA-25x based systems use this protocol
474 to talk with other Linux systems.
475
476 Although the ROMs shipped with Sharp Zaurus products use a
477 different link level framing protocol, you can have them use
478 this simpler protocol by installing a different kernel.
479
480config USB_EPSON2888
481 bool "Epson 2888 based firmware (DEVELOPMENT)"
482 depends on USB_NET_CDC_SUBSET
483 select USB_NET_CDC_SUBSET_ENABLE
484 help
485 Choose this option to support the usb networking links used
486 by some sample firmware from Epson.
487
488config USB_KC2190
489 bool "KT Technology KC2190 based cables (InstaNet)"
490 depends on USB_NET_CDC_SUBSET
491 select USB_NET_CDC_SUBSET_ENABLE
492 help
493 Choose this option if you're using a host-to-host cable
494 with one of these chips.
495
496config USB_NET_ZAURUS
497 tristate "Sharp Zaurus (stock ROMs) and compatible"
498 depends on USB_USBNET
499 select USB_NET_CDCETHER
500 select CRC32
501 default y
502 help
503 Choose this option to support the usb networking links used by
504 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
505 This also supports some related device firmware, as used in some
506 PDAs from Olympus and some cell phones from Motorola.
507
508 If you install an alternate image, such as the Linux 2.6 based
509 versions of OpenZaurus, you should no longer need to support this
510 protocol. Only the "eth-fd" or "net_fd" drivers in these devices
511 really need this non-conformant variant of CDC Ethernet (or in
512 some cases CDC MDLM) protocol, not "g_ether".
513
514config USB_NET_CX82310_ETH
515 tristate "Conexant CX82310 USB ethernet port"
516 depends on USB_USBNET
517 help
518 Choose this option if you're using a Conexant CX82310-based ADSL
519 router with USB ethernet port. This driver is for routers only,
520 it will not work with ADSL modems (use cxacru driver instead).
521
522config USB_NET_KALMIA
523 tristate "Samsung Kalmia based LTE USB modem"
524 depends on USB_USBNET
525 help
526 Choose this option if you have a Samsung Kalmia based USB modem
527 as Samsung GT-B3730.
528
529 To compile this driver as a module, choose M here: the
530 module will be called kalmia.
531
532config USB_NET_QMI_WWAN
533 tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems"
534 depends on USB_USBNET
535 select USB_WDM
536 help
537 Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem
538 (MDM) chipsets. Examples of such devices are
539 * Huawei E392/E398
540
541 This driver will only drive the ethernet part of the chips.
542 The devices require additional configuration to be usable.
543 Multiple management interfaces with linux drivers are
544 available:
545
546 * option: AT commands on /dev/ttyUSBx
547 * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx
548
549 A modem manager with support for QMI is recommended.
550
551 To compile this driver as a module, choose M here: the
552 module will be called qmi_wwan.
553
554config USB_HSO
555 tristate "Option USB High Speed Mobile Devices"
556 depends on USB && RFKILL && TTY
557 default n
558 help
559 Choose this option if you have an Option HSDPA/HSUPA card.
560 These cards support downlink speeds of 7.2Mbps or greater.
561
562 To compile this driver as a module, choose M here: the
563 module will be called hso.
564
565config USB_NET_INT51X1
566 tristate "Intellon PLC based usb adapter"
567 depends on USB_USBNET
568 help
569 Choose this option if you're using a 14Mb USB-based PLC
570 (Powerline Communications) solution with an Intellon
571 INT51x1/INT5200 chip, like the "devolo dLan duo".
572
573config USB_CDC_PHONET
574 tristate "CDC Phonet support"
575 depends on PHONET && USB_USBNET
576 help
577 Choose this option to support the Phonet interface to a Nokia
578 cellular modem, as found on most Nokia handsets with the
579 "PC suite" USB profile.
580
581config USB_IPHETH
582 tristate "Apple iPhone USB Ethernet driver"
583 default n
584 help
585 Module used to share Internet connection (tethering) from your
586 iPhone to your system.
587 Note that you need a corresponding userspace library/program
588 to pair your device with your system, for example usbmuxd
589 <https://github.com/libimobiledevice/usbmuxd>.
590
591config USB_SIERRA_NET
592 tristate "USB-to-WWAN Driver for Sierra Wireless modems"
593 depends on USB_USBNET
594 help
595 Choose this option if you have a Sierra Wireless USB-to-WWAN device.
596
597 To compile this driver as a module, choose M here: the
598 module will be called sierra_net.
599
600config USB_VL600
601 tristate "LG VL600 modem dongle"
602 depends on USB_NET_CDCETHER && TTY
603 select USB_ACM
604 help
605 Select this if you want to use an LG Electronics 4G/LTE usb modem
606 called VL600. This driver only handles the ethernet
607 interface exposed by the modem firmware. To establish a connection
608 you will first need a userspace program that sends the right
609 command to the modem through its CDC ACM port, and most
610 likely also a DHCP client. See this thread about using the
611 4G modem from Verizon:
612
613 http://ubuntuforums.org/showpost.php?p=10589647&postcount=17
614
615config USB_NET_CH9200
616 tristate "QingHeng CH9200 USB ethernet support"
617 depends on USB_USBNET
618 select MII
619 help
620 Choose this option if you have a USB ethernet adapter with a QinHeng
621 CH9200 chipset.
622
623 To compile this driver as a module, choose M here: the
624 module will be called ch9200.
625
626config USB_NET_AQC111
627 tristate "Aquantia AQtion USB to 5/2.5GbE Controllers support"
628 depends on USB_USBNET
629 select CRC32
630 help
631 This option adds support for Aquantia AQtion USB
632 Ethernet adapters based on AQC111U/AQC112 chips.
633
634 This driver should work with at least the following devices:
635 * Aquantia AQtion USB to 5GbE
636
637config USB_RTL8153_ECM
638 tristate
639 depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
640 default y
641 help
642 This option supports ECM mode for RTL8153 ethernet adapter, when
643 CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
644 supported by r8152 driver.
645
646endif # USB_NET_DRIVERS
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# USB Network devices configuration
4#
5comment "Host-side USB support is needed for USB Network Adapter support"
6 depends on !USB && NET
7
8menuconfig USB_NET_DRIVERS
9 tristate "USB Network Adapters"
10 default USB if USB
11 depends on USB && NET
12
13if USB_NET_DRIVERS
14
15config USB_CATC
16 tristate "USB CATC NetMate-based Ethernet device support"
17 select CRC32
18 help
19 Say Y if you want to use one of the following 10Mbps USB Ethernet
20 device based on the EL1210A chip. Supported devices are:
21 Belkin F5U011
22 Belkin F5U111
23 CATC NetMate
24 CATC NetMate II
25 smartBridges smartNIC
26
27 This driver makes the adapter appear as a normal Ethernet interface,
28 typically on eth0, if it is the only ethernet device, or perhaps on
29 eth1, if you have a PCI or ISA ethernet card installed.
30
31 To compile this driver as a module, choose M here: the
32 module will be called catc.
33
34config USB_KAWETH
35 tristate "USB KLSI KL5USB101-based ethernet device support"
36 help
37 Say Y here if you want to use one of the following 10Mbps only
38 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
39 3Com 3C19250
40 ADS USB-10BT
41 ATEN USB Ethernet
42 ASANTE USB To Ethernet Adapter
43 AOX Endpoints USB Ethernet
44 Correga K.K.
45 D-Link DSB-650C and DU-E10
46 Entrega / Portgear E45
47 I-O DATA USB-ET/T
48 Jaton USB Ethernet Device Adapter
49 Kingston Technology USB Ethernet Adapter
50 Linksys USB10T
51 Mobility USB-Ethernet Adapter
52 NetGear EA-101
53 Peracom Enet and Enet2
54 Portsmith Express Ethernet Adapter
55 Shark Pocket Adapter
56 SMC 2202USB
57 Sony Vaio port extender
58
59 This driver is likely to work with most 10Mbps only USB Ethernet
60 adapters, including some "no brand" devices. It does NOT work on
61 SmartBridges smartNIC or on Belkin F5U111 devices - you should use
62 the CATC NetMate driver for those. If you are not sure which one
63 you need, select both, and the correct one should be selected for
64 you.
65
66 This driver makes the adapter appear as a normal Ethernet interface,
67 typically on eth0, if it is the only ethernet device, or perhaps on
68 eth1, if you have a PCI or ISA ethernet card installed.
69
70 To compile this driver as a module, choose M here: the
71 module will be called kaweth.
72
73config USB_PEGASUS
74 tristate "USB Pegasus/Pegasus-II based ethernet device support"
75 select MII
76 help
77 Say Y here if you know you have Pegasus or Pegasus-II based adapter.
78 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
79 complete list of supported devices.
80
81 If your particular adapter is not in the list and you are _sure_ it
82 is Pegasus or Pegasus II based then send me
83 <petkan@users.sourceforge.net> vendor and device IDs.
84
85 To compile this driver as a module, choose M here: the
86 module will be called pegasus.
87
88config USB_RTL8150
89 tristate "USB RTL8150 based ethernet device support"
90 select MII
91 help
92 Say Y here if you have RTL8150 based usb-ethernet adapter.
93 Send me <petkan@users.sourceforge.net> any comments you may have.
94 You can also check for updates at <http://pegasus2.sourceforge.net/>.
95
96 To compile this driver as a module, choose M here: the
97 module will be called rtl8150.
98
99config USB_RTL8152
100 tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters"
101 select MII
102 select CRC32
103 select CRYPTO
104 select CRYPTO_HASH
105 select CRYPTO_SHA256
106 help
107 This option adds support for Realtek RTL8152 based USB 2.0
108 10/100 Ethernet adapters and RTL8153 based USB 3.0 10/100/1000
109 Ethernet adapters.
110
111 To compile this driver as a module, choose M here: the
112 module will be called r8152.
113
114config USB_LAN78XX
115 tristate "Microchip LAN78XX Based USB Ethernet Adapters"
116 select MII
117 select PHYLIB
118 select MICROCHIP_PHY
119 select FIXED_PHY
120 select CRC32
121 help
122 This option adds support for Microchip LAN78XX based USB 2
123 & USB 3 10/100/1000 Ethernet adapters.
124 LAN7800 : USB 3 to 10/100/1000 Ethernet adapter
125 LAN7850 : USB 2 to 10/100/1000 Ethernet adapter
126 LAN7801 : USB 3 to 10/100/1000 Ethernet adapter (MAC only)
127
128 Proper PHY driver is required for LAN7801.
129
130 To compile this driver as a module, choose M here: the
131 module will be called lan78xx.
132
133config USB_USBNET
134 tristate "Multi-purpose USB Networking Framework"
135 select MII
136 help
137 This driver supports several kinds of network links over USB,
138 with "minidrivers" built around a common network driver core
139 that supports deep queues for efficient transfers. (This gives
140 better performance with small packets and at high speeds).
141
142 The USB host runs "usbnet", and the other end of the link might be:
143
144 - Another USB host, when using USB "network" or "data transfer"
145 cables. These are often used to network laptops to PCs, like
146 "Laplink" parallel cables or some motherboards. These rely
147 on specialized chips from many suppliers.
148
149 - An intelligent USB gadget, perhaps embedding a Linux system.
150 These include PDAs running Linux (iPaq, Yopy, Zaurus, and
151 others), and devices that interoperate using the standard
152 CDC-Ethernet specification (including many cable modems).
153
154 - Network adapter hardware (like those for 10/100 Ethernet) which
155 uses this driver framework.
156
157 The link will appear with a name like "usb0", when the link is
158 a two-node link, or "eth0" for most CDC-Ethernet devices. Those
159 two-node links are most easily managed with Ethernet Bridging
160 (CONFIG_BRIDGE) instead of routing.
161
162 For more information see <http://www.linux-usb.org/usbnet/>.
163
164 To compile this driver as a module, choose M here: the
165 module will be called usbnet.
166
167config USB_NET_AX8817X
168 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
169 depends on USB_USBNET
170 select CRC32
171 select PHYLINK
172 select AX88796B_PHY
173 imply NET_SELFTESTS
174 default y
175 help
176 This option adds support for ASIX AX88xxx based USB 2.0
177 10/100 Ethernet adapters.
178
179 This driver should work with at least the following devices:
180 * Aten UC210T
181 * ASIX AX88172
182 * Billionton Systems, USB2AR
183 * Billionton Systems, GUSB2AM-1G-B
184 * Buffalo LUA-U2-KTX
185 * Corega FEther USB2-TX
186 * D-Link DUB-E100
187 * Hawking UF200
188 * Linksys USB200M
189 * Netgear FA120
190 * Sitecom LN-029
191 * Sitecom LN-028
192 * Intellinet USB 2.0 Ethernet
193 * ST Lab USB 2.0 Ethernet
194 * TrendNet TU2-ET100
195
196 This driver creates an interface named "ethX", where X depends on
197 what other networking devices you have in use.
198
199config USB_NET_AX88179_178A
200 tristate "ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet"
201 depends on USB_USBNET
202 select CRC32
203 select PHYLIB
204 default y
205 help
206 This option adds support for ASIX AX88179 based USB 3.0/2.0
207 to Gigabit Ethernet adapters.
208
209 This driver should work with at least the following devices:
210 * ASIX AX88179
211 * ASIX AX88178A
212 * Sitcomm LN-032
213
214 This driver creates an interface named "ethX", where X depends on
215 what other networking devices you have in use.
216
217config USB_NET_CDCETHER
218 tristate "CDC Ethernet support (smart devices such as cable modems)"
219 depends on USB_USBNET
220 default y
221 help
222 This option supports devices conforming to the Communication Device
223 Class (CDC) Ethernet Control Model, a specification that's easy to
224 implement in device firmware. The CDC specifications are available
225 from <http://www.usb.org/>.
226
227 CDC Ethernet is an implementation option for DOCSIS cable modems
228 that support USB connectivity, used for non-Microsoft USB hosts.
229 The Linux-USB CDC Ethernet Gadget driver is an open implementation.
230 This driver should work with at least the following devices:
231
232 * Dell Wireless 5530 HSPA
233 * Ericsson PipeRider (all variants)
234 * Ericsson Mobile Broadband Module (all variants)
235 * Motorola (DM100 and SB4100)
236 * Broadcom Cable Modem (reference design)
237 * Toshiba (PCX1100U and F3507g/F3607gw)
238 * ...
239
240 This driver creates an interface named "ethX", where X depends on
241 what other networking devices you have in use. However, if the
242 IEEE 802 "local assignment" bit is set in the address, a "usbX"
243 name is used instead.
244
245config USB_NET_CDC_EEM
246 tristate "CDC EEM support"
247 depends on USB_USBNET
248 help
249 This option supports devices conforming to the Communication Device
250 Class (CDC) Ethernet Emulation Model, a specification that's easy to
251 implement in device firmware. The CDC EEM specifications are available
252 from <http://www.usb.org/>.
253
254 This driver creates an interface named "ethX", where X depends on
255 what other networking devices you have in use. However, if the
256 IEEE 802 "local assignment" bit is set in the address, a "usbX"
257 name is used instead.
258
259config USB_NET_CDC_NCM
260 tristate "CDC NCM support"
261 depends on USB_USBNET
262 select USB_NET_CDCETHER
263 default y
264 help
265 This driver provides support for CDC NCM (Network Control Model
266 Device USB Class Specification). The CDC NCM specification is
267 available from <http://www.usb.org/>.
268
269 Say "y" to link the driver statically, or "m" to build a
270 dynamically linked module.
271
272 This driver should work with at least the following devices:
273 * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
274 * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
275 * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
276 * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
277 * Ericsson F5521gw Mobile Broadband Module
278
279config USB_NET_HUAWEI_CDC_NCM
280 tristate "Huawei NCM embedded AT channel support"
281 depends on USB_USBNET
282 select USB_WDM
283 select USB_NET_CDC_NCM
284 help
285 This driver supports huawei-style NCM devices, that use NCM as a
286 transport for other protocols, usually an embedded AT channel.
287 Good examples are:
288 * Huawei E3131
289 * Huawei E3251
290
291 To compile this driver as a module, choose M here: the module will be
292 called huawei_cdc_ncm.ko.
293
294config USB_NET_CDC_MBIM
295 tristate "CDC MBIM support"
296 depends on USB_USBNET
297 select USB_WDM
298 select USB_NET_CDC_NCM
299 help
300 This driver provides support for CDC MBIM (Mobile Broadband
301 Interface Model) devices. The CDC MBIM specification is
302 available from <http://www.usb.org/>.
303
304 MBIM devices require configuration using the management
305 protocol defined by the MBIM specification. This driver
306 provides unfiltered access to the MBIM control channel
307 through the associated /dev/cdc-wdmx character device.
308
309 To compile this driver as a module, choose M here: the
310 module will be called cdc_mbim.
311
312config USB_NET_DM9601
313 tristate "Davicom DM96xx based USB 10/100 ethernet devices"
314 depends on USB_USBNET
315 select CRC32
316 help
317 This option adds support for Davicom DM9601/DM9620/DM9621A
318 based USB 10/100 Ethernet adapters.
319
320config USB_NET_SR9700
321 tristate "CoreChip-sz SR9700 based USB 1.1 10/100 ethernet devices"
322 depends on USB_USBNET
323 select CRC32
324 help
325 This option adds support for CoreChip-sz SR9700 based USB 1.1
326 10/100 Ethernet adapters.
327
328config USB_NET_SR9800
329 tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices"
330 depends on USB_USBNET
331 select CRC32
332 help
333 Say Y if you want to use one of the following 100Mbps USB Ethernet
334 device based on the CoreChip-sz SR9800 chip.
335
336 This driver makes the adapter appear as a normal Ethernet interface,
337 typically on eth0, if it is the only ethernet device, or perhaps on
338 eth1, if you have a PCI or ISA ethernet card installed.
339
340 To compile this driver as a module, choose M here: the
341 module will be called sr9800.
342
343config USB_NET_SMSC75XX
344 tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
345 depends on USB_USBNET
346 select BITREVERSE
347 select CRC16
348 select CRC32
349 help
350 This option adds support for SMSC LAN75XX based USB 2.0
351 Gigabit Ethernet adapters.
352
353config USB_NET_SMSC95XX
354 tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
355 depends on USB_USBNET
356 select PHYLIB
357 select SMSC_PHY
358 select BITREVERSE
359 select CRC16
360 select CRC32
361 imply NET_SELFTESTS
362 help
363 This option adds support for SMSC LAN95XX based USB 2.0
364 10/100 Ethernet adapters.
365
366config USB_NET_GL620A
367 tristate "GeneSys GL620USB-A based cables"
368 depends on USB_USBNET
369 help
370 Choose this option if you're using a host-to-host cable,
371 or PC2PC motherboard, with this chip.
372
373 Note that the half-duplex "GL620USB" is not supported.
374
375config USB_NET_NET1080
376 tristate "NetChip 1080 based cables (Laplink, ...)"
377 default y
378 depends on USB_USBNET
379 help
380 Choose this option if you're using a host-to-host cable based
381 on this design: one NetChip 1080 chip and supporting logic,
382 optionally with LEDs that indicate traffic
383
384config USB_NET_PLUSB
385 tristate "Prolific PL-2301/2302/25A1/27A1 based cables"
386 # if the handshake/init/reset problems, from original 'plusb',
387 # are ever resolved ... then remove "experimental"
388 depends on USB_USBNET
389 help
390 Choose this option if you're using a host-to-host cable
391 with one of these chips.
392
393config USB_NET_MCS7830
394 tristate "MosChip MCS7830 based Ethernet adapters"
395 depends on USB_USBNET
396 help
397 Choose this option if you're using a 10/100 Ethernet USB2
398 adapter based on the MosChip 7830 controller. This includes
399 adapters marketed under the DeLOCK brand.
400
401config USB_NET_RNDIS_HOST
402 tristate "Host for RNDIS and ActiveSync devices"
403 depends on USB_USBNET
404 select USB_NET_CDCETHER
405 help
406 This option enables hosting "Remote NDIS" USB networking links,
407 as encouraged by Microsoft (instead of CDC Ethernet!) for use in
408 various devices that may only support this protocol. A variant
409 of this protocol (with even less public documentation) seems to
410 be at the root of Microsoft's "ActiveSync" too.
411
412 Avoid using this protocol unless you have no better options.
413 The protocol specification is incomplete, and is controlled by
414 (and for) Microsoft; it isn't an "Open" ecosystem or market.
415
416config USB_NET_CDC_SUBSET_ENABLE
417 tristate
418 depends on USB_NET_CDC_SUBSET
419
420config USB_NET_CDC_SUBSET
421 tristate "Simple USB Network Links (CDC Ethernet subset)"
422 depends on USB_USBNET
423 default y
424 help
425 This driver module supports USB network devices that can work
426 without any device-specific information. Select it if you have
427 one of these drivers.
428
429 Note that while many USB host-to-host cables can work in this mode,
430 that may mean not being able to talk to Win32 systems or more
431 commonly not being able to handle certain events (like replugging
432 the host on the other end) very well. Also, these devices will
433 not generally have permanently assigned Ethernet addresses.
434
435config USB_ALI_M5632
436 bool "ALi M5632 based 'USB 2.0 Data Link' cables"
437 depends on USB_NET_CDC_SUBSET
438 select USB_NET_CDC_SUBSET_ENABLE
439 help
440 Choose this option if you're using a host-to-host cable
441 based on this design, which supports USB 2.0 high speed.
442
443config USB_AN2720
444 bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
445 depends on USB_NET_CDC_SUBSET
446 select USB_NET_CDC_SUBSET_ENABLE
447 help
448 Choose this option if you're using a host-to-host cable
449 based on this design. Note that AnchorChips is now a
450 Cypress brand.
451
452config USB_BELKIN
453 bool "eTEK based host-to-host cables (Advance, Belkin, ...)"
454 depends on USB_NET_CDC_SUBSET
455 select USB_NET_CDC_SUBSET_ENABLE
456 default y
457 help
458 Choose this option if you're using a host-to-host cable
459 based on this design: two NetChip 2890 chips and an Atmel
460 microcontroller, with LEDs that indicate traffic.
461
462config USB_ARMLINUX
463 bool "Embedded ARM Linux links (iPaq, ...)"
464 depends on USB_NET_CDC_SUBSET
465 select USB_NET_CDC_SUBSET_ENABLE
466 default y
467 help
468 Choose this option to support the "usb-eth" networking driver
469 used by most of the ARM Linux community with device controllers
470 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
471 in some PXA versions of the "blob" boot loader.
472
473 Linux-based "Gumstix" PXA-25x based systems use this protocol
474 to talk with other Linux systems.
475
476 Although the ROMs shipped with Sharp Zaurus products use a
477 different link level framing protocol, you can have them use
478 this simpler protocol by installing a different kernel.
479
480config USB_EPSON2888
481 bool "Epson 2888 based firmware (DEVELOPMENT)"
482 depends on USB_NET_CDC_SUBSET
483 select USB_NET_CDC_SUBSET_ENABLE
484 help
485 Choose this option to support the usb networking links used
486 by some sample firmware from Epson.
487
488config USB_KC2190
489 bool "KT Technology KC2190 based cables (InstaNet)"
490 depends on USB_NET_CDC_SUBSET
491 select USB_NET_CDC_SUBSET_ENABLE
492 help
493 Choose this option if you're using a host-to-host cable
494 with one of these chips.
495
496config USB_NET_ZAURUS
497 tristate "Sharp Zaurus (stock ROMs) and compatible"
498 depends on USB_USBNET
499 select USB_NET_CDCETHER
500 select CRC32
501 default y
502 help
503 Choose this option to support the usb networking links used by
504 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
505 This also supports some related device firmware, as used in some
506 PDAs from Olympus and some cell phones from Motorola.
507
508 If you install an alternate image, such as the Linux 2.6 based
509 versions of OpenZaurus, you should no longer need to support this
510 protocol. Only the "eth-fd" or "net_fd" drivers in these devices
511 really need this non-conformant variant of CDC Ethernet (or in
512 some cases CDC MDLM) protocol, not "g_ether".
513
514config USB_NET_CX82310_ETH
515 tristate "Conexant CX82310 USB ethernet port"
516 depends on USB_USBNET
517 help
518 Choose this option if you're using a Conexant CX82310-based ADSL
519 router with USB ethernet port. This driver is for routers only,
520 it will not work with ADSL modems (use cxacru driver instead).
521
522config USB_NET_KALMIA
523 tristate "Samsung Kalmia based LTE USB modem"
524 depends on USB_USBNET
525 help
526 Choose this option if you have a Samsung Kalmia based USB modem
527 as Samsung GT-B3730.
528
529 To compile this driver as a module, choose M here: the
530 module will be called kalmia.
531
532config USB_NET_QMI_WWAN
533 tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems"
534 depends on USB_USBNET
535 select USB_WDM
536 help
537 Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem
538 (MDM) chipsets. Examples of such devices are
539 * Huawei E392/E398
540
541 This driver will only drive the ethernet part of the chips.
542 The devices require additional configuration to be usable.
543 Multiple management interfaces with linux drivers are
544 available:
545
546 * option: AT commands on /dev/ttyUSBx
547 * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx
548
549 A modem manager with support for QMI is recommended.
550
551 To compile this driver as a module, choose M here: the
552 module will be called qmi_wwan.
553
554config USB_HSO
555 tristate "Option USB High Speed Mobile Devices"
556 depends on USB && RFKILL && TTY
557 default n
558 help
559 Choose this option if you have an Option HSDPA/HSUPA card.
560 These cards support downlink speeds of 7.2Mbps or greater.
561
562 To compile this driver as a module, choose M here: the
563 module will be called hso.
564
565config USB_NET_INT51X1
566 tristate "Intellon PLC based usb adapter"
567 depends on USB_USBNET
568 help
569 Choose this option if you're using a 14Mb USB-based PLC
570 (Powerline Communications) solution with an Intellon
571 INT51x1/INT5200 chip, like the "devolo dLan duo".
572
573config USB_CDC_PHONET
574 tristate "CDC Phonet support"
575 depends on PHONET && USB_USBNET
576 help
577 Choose this option to support the Phonet interface to a Nokia
578 cellular modem, as found on most Nokia handsets with the
579 "PC suite" USB profile.
580
581config USB_IPHETH
582 tristate "Apple iPhone USB Ethernet driver"
583 default n
584 help
585 Module used to share Internet connection (tethering) from your
586 iPhone (Original, 3G and 3GS) to your system.
587 Note that you need userspace libraries and programs that are needed
588 to pair your device with your system and that understand the iPhone
589 protocol.
590
591 For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver
592
593config USB_SIERRA_NET
594 tristate "USB-to-WWAN Driver for Sierra Wireless modems"
595 depends on USB_USBNET
596 help
597 Choose this option if you have a Sierra Wireless USB-to-WWAN device.
598
599 To compile this driver as a module, choose M here: the
600 module will be called sierra_net.
601
602config USB_VL600
603 tristate "LG VL600 modem dongle"
604 depends on USB_NET_CDCETHER && TTY
605 select USB_ACM
606 help
607 Select this if you want to use an LG Electronics 4G/LTE usb modem
608 called VL600. This driver only handles the ethernet
609 interface exposed by the modem firmware. To establish a connection
610 you will first need a userspace program that sends the right
611 command to the modem through its CDC ACM port, and most
612 likely also a DHCP client. See this thread about using the
613 4G modem from Verizon:
614
615 http://ubuntuforums.org/showpost.php?p=10589647&postcount=17
616
617config USB_NET_CH9200
618 tristate "QingHeng CH9200 USB ethernet support"
619 depends on USB_USBNET
620 select MII
621 help
622 Choose this option if you have a USB ethernet adapter with a QinHeng
623 CH9200 chipset.
624
625 To compile this driver as a module, choose M here: the
626 module will be called ch9200.
627
628config USB_NET_AQC111
629 tristate "Aquantia AQtion USB to 5/2.5GbE Controllers support"
630 depends on USB_USBNET
631 select CRC32
632 help
633 This option adds support for Aquantia AQtion USB
634 Ethernet adapters based on AQC111U/AQC112 chips.
635
636 This driver should work with at least the following devices:
637 * Aquantia AQtion USB to 5GbE
638
639config USB_RTL8153_ECM
640 tristate
641 depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
642 default y
643 help
644 This option supports ECM mode for RTL8153 ethernet adapter, when
645 CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
646 supported by r8152 driver.
647
648endif # USB_NET_DRIVERS