Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Xilinx SPI controller driver (host mode only)
4 *
5 * Author: MontaVista Software, Inc.
6 * source@mvista.com
7 *
8 * Copyright (c) 2010 Secret Lab Technologies, Ltd.
9 * Copyright (c) 2009 Intel Corporation
10 * 2002-2007 (c) MontaVista Software, Inc.
11
12 */
13
14#include <linux/module.h>
15#include <linux/interrupt.h>
16#include <linux/of.h>
17#include <linux/platform_device.h>
18#include <linux/spi/spi.h>
19#include <linux/spi/spi_bitbang.h>
20#include <linux/spi/xilinx_spi.h>
21#include <linux/io.h>
22
23#define XILINX_SPI_MAX_CS 32
24
25#define XILINX_SPI_NAME "xilinx_spi"
26
27/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
28 * Product Specification", DS464
29 */
30#define XSPI_CR_OFFSET 0x60 /* Control Register */
31
32#define XSPI_CR_LOOP 0x01
33#define XSPI_CR_ENABLE 0x02
34#define XSPI_CR_MASTER_MODE 0x04
35#define XSPI_CR_CPOL 0x08
36#define XSPI_CR_CPHA 0x10
37#define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL | \
38 XSPI_CR_LSB_FIRST | XSPI_CR_LOOP)
39#define XSPI_CR_TXFIFO_RESET 0x20
40#define XSPI_CR_RXFIFO_RESET 0x40
41#define XSPI_CR_MANUAL_SSELECT 0x80
42#define XSPI_CR_TRANS_INHIBIT 0x100
43#define XSPI_CR_LSB_FIRST 0x200
44
45#define XSPI_SR_OFFSET 0x64 /* Status Register */
46
47#define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */
48#define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */
49#define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */
50#define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */
51#define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */
52
53#define XSPI_TXD_OFFSET 0x68 /* Data Transmit Register */
54#define XSPI_RXD_OFFSET 0x6c /* Data Receive Register */
55
56#define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */
57
58/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
59 * IPIF registers are 32 bit
60 */
61#define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */
62#define XIPIF_V123B_GINTR_ENABLE 0x80000000
63
64#define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */
65#define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */
66
67#define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */
68#define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while
69 * disabled */
70#define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */
71#define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */
72#define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */
73#define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */
74#define XSPI_INTR_TX_HALF_EMPTY 0x40 /* TxFIFO is half empty */
75
76#define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */
77#define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */
78
79struct xilinx_spi {
80 /* bitbang has to be first */
81 struct spi_bitbang bitbang;
82 struct completion done;
83 void __iomem *regs; /* virt. address of the control registers */
84
85 int irq;
86 bool force_irq; /* force irq to setup host inhibit */
87 u8 *rx_ptr; /* pointer in the Tx buffer */
88 const u8 *tx_ptr; /* pointer in the Rx buffer */
89 u8 bytes_per_word;
90 int buffer_size; /* buffer size in words */
91 u32 cs_inactive; /* Level of the CS pins when inactive*/
92 unsigned int (*read_fn)(void __iomem *);
93 void (*write_fn)(u32, void __iomem *);
94};
95
96static void xspi_write32(u32 val, void __iomem *addr)
97{
98 iowrite32(val, addr);
99}
100
101static unsigned int xspi_read32(void __iomem *addr)
102{
103 return ioread32(addr);
104}
105
106static void xspi_write32_be(u32 val, void __iomem *addr)
107{
108 iowrite32be(val, addr);
109}
110
111static unsigned int xspi_read32_be(void __iomem *addr)
112{
113 return ioread32be(addr);
114}
115
116static void xilinx_spi_tx(struct xilinx_spi *xspi)
117{
118 u32 data = 0;
119
120 if (!xspi->tx_ptr) {
121 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
122 return;
123 }
124
125 switch (xspi->bytes_per_word) {
126 case 1:
127 data = *(u8 *)(xspi->tx_ptr);
128 break;
129 case 2:
130 data = *(u16 *)(xspi->tx_ptr);
131 break;
132 case 4:
133 data = *(u32 *)(xspi->tx_ptr);
134 break;
135 }
136
137 xspi->write_fn(data, xspi->regs + XSPI_TXD_OFFSET);
138 xspi->tx_ptr += xspi->bytes_per_word;
139}
140
141static void xilinx_spi_rx(struct xilinx_spi *xspi)
142{
143 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
144
145 if (!xspi->rx_ptr)
146 return;
147
148 switch (xspi->bytes_per_word) {
149 case 1:
150 *(u8 *)(xspi->rx_ptr) = data;
151 break;
152 case 2:
153 *(u16 *)(xspi->rx_ptr) = data;
154 break;
155 case 4:
156 *(u32 *)(xspi->rx_ptr) = data;
157 break;
158 }
159
160 xspi->rx_ptr += xspi->bytes_per_word;
161}
162
163static void xspi_init_hw(struct xilinx_spi *xspi)
164{
165 void __iomem *regs_base = xspi->regs;
166
167 /* Reset the SPI device */
168 xspi->write_fn(XIPIF_V123B_RESET_MASK,
169 regs_base + XIPIF_V123B_RESETR_OFFSET);
170 /* Enable the transmit empty interrupt, which we use to determine
171 * progress on the transmission.
172 */
173 xspi->write_fn(XSPI_INTR_TX_EMPTY,
174 regs_base + XIPIF_V123B_IIER_OFFSET);
175 /* Disable the global IPIF interrupt */
176 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
177 /* Deselect the Target on the SPI bus */
178 xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
179 /* Disable the transmitter, enable Manual Target Select Assertion,
180 * put SPI controller into host mode, and enable it */
181 xspi->write_fn(XSPI_CR_MANUAL_SSELECT | XSPI_CR_MASTER_MODE |
182 XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET | XSPI_CR_RXFIFO_RESET,
183 regs_base + XSPI_CR_OFFSET);
184}
185
186static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
187{
188 struct xilinx_spi *xspi = spi_controller_get_devdata(spi->controller);
189 u16 cr;
190 u32 cs;
191
192 if (is_on == BITBANG_CS_INACTIVE) {
193 /* Deselect the target on the SPI bus */
194 xspi->write_fn(xspi->cs_inactive, xspi->regs + XSPI_SSR_OFFSET);
195 return;
196 }
197
198 /* Set the SPI clock phase and polarity */
199 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_MODE_MASK;
200 if (spi->mode & SPI_CPHA)
201 cr |= XSPI_CR_CPHA;
202 if (spi->mode & SPI_CPOL)
203 cr |= XSPI_CR_CPOL;
204 if (spi->mode & SPI_LSB_FIRST)
205 cr |= XSPI_CR_LSB_FIRST;
206 if (spi->mode & SPI_LOOP)
207 cr |= XSPI_CR_LOOP;
208 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
209
210 /* We do not check spi->max_speed_hz here as the SPI clock
211 * frequency is not software programmable (the IP block design
212 * parameter)
213 */
214
215 cs = xspi->cs_inactive;
216 cs ^= BIT(spi_get_chipselect(spi, 0));
217
218 /* Activate the chip select */
219 xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET);
220}
221
222/* spi_bitbang requires custom setup_transfer() to be defined if there is a
223 * custom txrx_bufs().
224 */
225static int xilinx_spi_setup_transfer(struct spi_device *spi,
226 struct spi_transfer *t)
227{
228 struct xilinx_spi *xspi = spi_controller_get_devdata(spi->controller);
229
230 if (spi->mode & SPI_CS_HIGH)
231 xspi->cs_inactive &= ~BIT(spi_get_chipselect(spi, 0));
232 else
233 xspi->cs_inactive |= BIT(spi_get_chipselect(spi, 0));
234
235 return 0;
236}
237
238static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
239{
240 struct xilinx_spi *xspi = spi_controller_get_devdata(spi->controller);
241 int remaining_words; /* the number of words left to transfer */
242 bool use_irq = false;
243 u16 cr = 0;
244
245 /* We get here with transmitter inhibited */
246
247 xspi->tx_ptr = t->tx_buf;
248 xspi->rx_ptr = t->rx_buf;
249 remaining_words = t->len / xspi->bytes_per_word;
250
251 if (xspi->irq >= 0 &&
252 (xspi->force_irq || remaining_words > xspi->buffer_size)) {
253 u32 isr;
254 use_irq = true;
255 /* Inhibit irq to avoid spurious irqs on tx_empty*/
256 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
257 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
258 xspi->regs + XSPI_CR_OFFSET);
259 /* ACK old irqs (if any) */
260 isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
261 if (isr)
262 xspi->write_fn(isr,
263 xspi->regs + XIPIF_V123B_IISR_OFFSET);
264 /* Enable the global IPIF interrupt */
265 xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
266 xspi->regs + XIPIF_V123B_DGIER_OFFSET);
267 reinit_completion(&xspi->done);
268 }
269
270 while (remaining_words) {
271 int n_words, tx_words, rx_words;
272 u32 sr;
273 int stalled;
274
275 n_words = min(remaining_words, xspi->buffer_size);
276
277 tx_words = n_words;
278 while (tx_words--)
279 xilinx_spi_tx(xspi);
280
281 /* Start the transfer by not inhibiting the transmitter any
282 * longer
283 */
284
285 if (use_irq) {
286 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
287 wait_for_completion(&xspi->done);
288 /* A transmit has just completed. Process received data
289 * and check for more data to transmit. Always inhibit
290 * the transmitter while the Isr refills the transmit
291 * register/FIFO, or make sure it is stopped if we're
292 * done.
293 */
294 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
295 xspi->regs + XSPI_CR_OFFSET);
296 sr = XSPI_SR_TX_EMPTY_MASK;
297 } else
298 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
299
300 /* Read out all the data from the Rx FIFO */
301 rx_words = n_words;
302 stalled = 10;
303 while (rx_words) {
304 if (rx_words == n_words && !(stalled--) &&
305 !(sr & XSPI_SR_TX_EMPTY_MASK) &&
306 (sr & XSPI_SR_RX_EMPTY_MASK)) {
307 dev_err(&spi->dev,
308 "Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n");
309 xspi_init_hw(xspi);
310 return -EIO;
311 }
312
313 if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
314 xilinx_spi_rx(xspi);
315 rx_words--;
316 continue;
317 }
318
319 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
320 if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
321 xilinx_spi_rx(xspi);
322 rx_words--;
323 }
324 }
325
326 remaining_words -= n_words;
327 }
328
329 if (use_irq) {
330 xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
331 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
332 }
333
334 return t->len;
335}
336
337
338/* This driver supports single host mode only. Hence Tx FIFO Empty
339 * is the only interrupt we care about.
340 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Target Mode
341 * Fault are not to happen.
342 */
343static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
344{
345 struct xilinx_spi *xspi = dev_id;
346 u32 ipif_isr;
347
348 /* Get the IPIF interrupts, and clear them immediately */
349 ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
350 xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
351
352 if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */
353 complete(&xspi->done);
354 return IRQ_HANDLED;
355 }
356
357 return IRQ_NONE;
358}
359
360static int xilinx_spi_find_buffer_size(struct xilinx_spi *xspi)
361{
362 u8 sr;
363 int n_words = 0;
364
365 /*
366 * Before the buffer_size detection we reset the core
367 * to make sure we start with a clean state.
368 */
369 xspi->write_fn(XIPIF_V123B_RESET_MASK,
370 xspi->regs + XIPIF_V123B_RESETR_OFFSET);
371
372 /* Fill the Tx FIFO with as many words as possible */
373 do {
374 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
375 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
376 n_words++;
377 } while (!(sr & XSPI_SR_TX_FULL_MASK));
378
379 return n_words;
380}
381
382static const struct of_device_id xilinx_spi_of_match[] = {
383 { .compatible = "xlnx,axi-quad-spi-1.00.a", },
384 { .compatible = "xlnx,xps-spi-2.00.a", },
385 { .compatible = "xlnx,xps-spi-2.00.b", },
386 {}
387};
388MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
389
390static int xilinx_spi_probe(struct platform_device *pdev)
391{
392 struct xilinx_spi *xspi;
393 struct xspi_platform_data *pdata;
394 struct resource *res;
395 int ret, num_cs = 0, bits_per_word;
396 struct spi_controller *host;
397 bool force_irq = false;
398 u32 tmp;
399 u8 i;
400
401 pdata = dev_get_platdata(&pdev->dev);
402 if (pdata) {
403 num_cs = pdata->num_chipselect;
404 bits_per_word = pdata->bits_per_word;
405 force_irq = pdata->force_irq;
406 } else {
407 of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits",
408 &num_cs);
409 ret = of_property_read_u32(pdev->dev.of_node,
410 "xlnx,num-transfer-bits",
411 &bits_per_word);
412 if (ret)
413 bits_per_word = 8;
414 }
415
416 if (!num_cs) {
417 dev_err(&pdev->dev,
418 "Missing target select configuration data\n");
419 return -EINVAL;
420 }
421
422 if (num_cs > XILINX_SPI_MAX_CS) {
423 dev_err(&pdev->dev, "Invalid number of spi targets\n");
424 return -EINVAL;
425 }
426
427 host = devm_spi_alloc_host(&pdev->dev, sizeof(struct xilinx_spi));
428 if (!host)
429 return -ENODEV;
430
431 /* the spi->mode bits understood by this driver: */
432 host->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP |
433 SPI_CS_HIGH;
434
435 xspi = spi_controller_get_devdata(host);
436 xspi->cs_inactive = 0xffffffff;
437 xspi->bitbang.master = host;
438 xspi->bitbang.chipselect = xilinx_spi_chipselect;
439 xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
440 xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
441 init_completion(&xspi->done);
442
443 xspi->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
444 if (IS_ERR(xspi->regs))
445 return PTR_ERR(xspi->regs);
446
447 host->bus_num = pdev->id;
448 host->num_chipselect = num_cs;
449 host->dev.of_node = pdev->dev.of_node;
450
451 /*
452 * Detect endianess on the IP via loop bit in CR. Detection
453 * must be done before reset is sent because incorrect reset
454 * value generates error interrupt.
455 * Setup little endian helper functions first and try to use them
456 * and check if bit was correctly setup or not.
457 */
458 xspi->read_fn = xspi_read32;
459 xspi->write_fn = xspi_write32;
460
461 xspi->write_fn(XSPI_CR_LOOP, xspi->regs + XSPI_CR_OFFSET);
462 tmp = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
463 tmp &= XSPI_CR_LOOP;
464 if (tmp != XSPI_CR_LOOP) {
465 xspi->read_fn = xspi_read32_be;
466 xspi->write_fn = xspi_write32_be;
467 }
468
469 host->bits_per_word_mask = SPI_BPW_MASK(bits_per_word);
470 xspi->bytes_per_word = bits_per_word / 8;
471 xspi->buffer_size = xilinx_spi_find_buffer_size(xspi);
472
473 xspi->irq = platform_get_irq(pdev, 0);
474 if (xspi->irq < 0 && xspi->irq != -ENXIO) {
475 return xspi->irq;
476 } else if (xspi->irq >= 0) {
477 /* Register for SPI Interrupt */
478 ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0,
479 dev_name(&pdev->dev), xspi);
480 if (ret)
481 return ret;
482
483 xspi->force_irq = force_irq;
484 }
485
486 /* SPI controller initializations */
487 xspi_init_hw(xspi);
488
489 ret = spi_bitbang_start(&xspi->bitbang);
490 if (ret) {
491 dev_err(&pdev->dev, "spi_bitbang_start FAILED\n");
492 return ret;
493 }
494
495 dev_info(&pdev->dev, "at %pR, irq=%d\n", res, xspi->irq);
496
497 if (pdata) {
498 for (i = 0; i < pdata->num_devices; i++)
499 spi_new_device(host, pdata->devices + i);
500 }
501
502 platform_set_drvdata(pdev, host);
503 return 0;
504}
505
506static void xilinx_spi_remove(struct platform_device *pdev)
507{
508 struct spi_controller *host = platform_get_drvdata(pdev);
509 struct xilinx_spi *xspi = spi_controller_get_devdata(host);
510 void __iomem *regs_base = xspi->regs;
511
512 spi_bitbang_stop(&xspi->bitbang);
513
514 /* Disable all the interrupts just in case */
515 xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
516 /* Disable the global IPIF interrupt */
517 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
518
519 spi_controller_put(xspi->bitbang.master);
520}
521
522/* work with hotplug and coldplug */
523MODULE_ALIAS("platform:" XILINX_SPI_NAME);
524
525static struct platform_driver xilinx_spi_driver = {
526 .probe = xilinx_spi_probe,
527 .remove_new = xilinx_spi_remove,
528 .driver = {
529 .name = XILINX_SPI_NAME,
530 .of_match_table = xilinx_spi_of_match,
531 },
532};
533module_platform_driver(xilinx_spi_driver);
534
535MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
536MODULE_DESCRIPTION("Xilinx SPI driver");
537MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Xilinx SPI controller driver (master mode only)
4 *
5 * Author: MontaVista Software, Inc.
6 * source@mvista.com
7 *
8 * Copyright (c) 2010 Secret Lab Technologies, Ltd.
9 * Copyright (c) 2009 Intel Corporation
10 * 2002-2007 (c) MontaVista Software, Inc.
11
12 */
13
14#include <linux/module.h>
15#include <linux/interrupt.h>
16#include <linux/of.h>
17#include <linux/platform_device.h>
18#include <linux/spi/spi.h>
19#include <linux/spi/spi_bitbang.h>
20#include <linux/spi/xilinx_spi.h>
21#include <linux/io.h>
22
23#define XILINX_SPI_MAX_CS 32
24
25#define XILINX_SPI_NAME "xilinx_spi"
26
27/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
28 * Product Specification", DS464
29 */
30#define XSPI_CR_OFFSET 0x60 /* Control Register */
31
32#define XSPI_CR_LOOP 0x01
33#define XSPI_CR_ENABLE 0x02
34#define XSPI_CR_MASTER_MODE 0x04
35#define XSPI_CR_CPOL 0x08
36#define XSPI_CR_CPHA 0x10
37#define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL | \
38 XSPI_CR_LSB_FIRST | XSPI_CR_LOOP)
39#define XSPI_CR_TXFIFO_RESET 0x20
40#define XSPI_CR_RXFIFO_RESET 0x40
41#define XSPI_CR_MANUAL_SSELECT 0x80
42#define XSPI_CR_TRANS_INHIBIT 0x100
43#define XSPI_CR_LSB_FIRST 0x200
44
45#define XSPI_SR_OFFSET 0x64 /* Status Register */
46
47#define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */
48#define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */
49#define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */
50#define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */
51#define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */
52
53#define XSPI_TXD_OFFSET 0x68 /* Data Transmit Register */
54#define XSPI_RXD_OFFSET 0x6c /* Data Receive Register */
55
56#define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */
57
58/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
59 * IPIF registers are 32 bit
60 */
61#define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */
62#define XIPIF_V123B_GINTR_ENABLE 0x80000000
63
64#define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */
65#define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */
66
67#define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */
68#define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while
69 * disabled */
70#define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */
71#define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */
72#define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */
73#define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */
74#define XSPI_INTR_TX_HALF_EMPTY 0x40 /* TxFIFO is half empty */
75
76#define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */
77#define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */
78
79struct xilinx_spi {
80 /* bitbang has to be first */
81 struct spi_bitbang bitbang;
82 struct completion done;
83 void __iomem *regs; /* virt. address of the control registers */
84
85 int irq;
86
87 u8 *rx_ptr; /* pointer in the Tx buffer */
88 const u8 *tx_ptr; /* pointer in the Rx buffer */
89 u8 bytes_per_word;
90 int buffer_size; /* buffer size in words */
91 u32 cs_inactive; /* Level of the CS pins when inactive*/
92 unsigned int (*read_fn)(void __iomem *);
93 void (*write_fn)(u32, void __iomem *);
94};
95
96static void xspi_write32(u32 val, void __iomem *addr)
97{
98 iowrite32(val, addr);
99}
100
101static unsigned int xspi_read32(void __iomem *addr)
102{
103 return ioread32(addr);
104}
105
106static void xspi_write32_be(u32 val, void __iomem *addr)
107{
108 iowrite32be(val, addr);
109}
110
111static unsigned int xspi_read32_be(void __iomem *addr)
112{
113 return ioread32be(addr);
114}
115
116static void xilinx_spi_tx(struct xilinx_spi *xspi)
117{
118 u32 data = 0;
119
120 if (!xspi->tx_ptr) {
121 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
122 return;
123 }
124
125 switch (xspi->bytes_per_word) {
126 case 1:
127 data = *(u8 *)(xspi->tx_ptr);
128 break;
129 case 2:
130 data = *(u16 *)(xspi->tx_ptr);
131 break;
132 case 4:
133 data = *(u32 *)(xspi->tx_ptr);
134 break;
135 }
136
137 xspi->write_fn(data, xspi->regs + XSPI_TXD_OFFSET);
138 xspi->tx_ptr += xspi->bytes_per_word;
139}
140
141static void xilinx_spi_rx(struct xilinx_spi *xspi)
142{
143 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
144
145 if (!xspi->rx_ptr)
146 return;
147
148 switch (xspi->bytes_per_word) {
149 case 1:
150 *(u8 *)(xspi->rx_ptr) = data;
151 break;
152 case 2:
153 *(u16 *)(xspi->rx_ptr) = data;
154 break;
155 case 4:
156 *(u32 *)(xspi->rx_ptr) = data;
157 break;
158 }
159
160 xspi->rx_ptr += xspi->bytes_per_word;
161}
162
163static void xspi_init_hw(struct xilinx_spi *xspi)
164{
165 void __iomem *regs_base = xspi->regs;
166
167 /* Reset the SPI device */
168 xspi->write_fn(XIPIF_V123B_RESET_MASK,
169 regs_base + XIPIF_V123B_RESETR_OFFSET);
170 /* Enable the transmit empty interrupt, which we use to determine
171 * progress on the transmission.
172 */
173 xspi->write_fn(XSPI_INTR_TX_EMPTY,
174 regs_base + XIPIF_V123B_IIER_OFFSET);
175 /* Disable the global IPIF interrupt */
176 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
177 /* Deselect the slave on the SPI bus */
178 xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
179 /* Disable the transmitter, enable Manual Slave Select Assertion,
180 * put SPI controller into master mode, and enable it */
181 xspi->write_fn(XSPI_CR_MANUAL_SSELECT | XSPI_CR_MASTER_MODE |
182 XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET | XSPI_CR_RXFIFO_RESET,
183 regs_base + XSPI_CR_OFFSET);
184}
185
186static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
187{
188 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
189 u16 cr;
190 u32 cs;
191
192 if (is_on == BITBANG_CS_INACTIVE) {
193 /* Deselect the slave on the SPI bus */
194 xspi->write_fn(xspi->cs_inactive, xspi->regs + XSPI_SSR_OFFSET);
195 return;
196 }
197
198 /* Set the SPI clock phase and polarity */
199 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_MODE_MASK;
200 if (spi->mode & SPI_CPHA)
201 cr |= XSPI_CR_CPHA;
202 if (spi->mode & SPI_CPOL)
203 cr |= XSPI_CR_CPOL;
204 if (spi->mode & SPI_LSB_FIRST)
205 cr |= XSPI_CR_LSB_FIRST;
206 if (spi->mode & SPI_LOOP)
207 cr |= XSPI_CR_LOOP;
208 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
209
210 /* We do not check spi->max_speed_hz here as the SPI clock
211 * frequency is not software programmable (the IP block design
212 * parameter)
213 */
214
215 cs = xspi->cs_inactive;
216 cs ^= BIT(spi->chip_select);
217
218 /* Activate the chip select */
219 xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET);
220}
221
222/* spi_bitbang requires custom setup_transfer() to be defined if there is a
223 * custom txrx_bufs().
224 */
225static int xilinx_spi_setup_transfer(struct spi_device *spi,
226 struct spi_transfer *t)
227{
228 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
229
230 if (spi->mode & SPI_CS_HIGH)
231 xspi->cs_inactive &= ~BIT(spi->chip_select);
232 else
233 xspi->cs_inactive |= BIT(spi->chip_select);
234
235 return 0;
236}
237
238static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
239{
240 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
241 int remaining_words; /* the number of words left to transfer */
242 bool use_irq = false;
243 u16 cr = 0;
244
245 /* We get here with transmitter inhibited */
246
247 xspi->tx_ptr = t->tx_buf;
248 xspi->rx_ptr = t->rx_buf;
249 remaining_words = t->len / xspi->bytes_per_word;
250
251 if (xspi->irq >= 0 && remaining_words > xspi->buffer_size) {
252 u32 isr;
253 use_irq = true;
254 /* Inhibit irq to avoid spurious irqs on tx_empty*/
255 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
256 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
257 xspi->regs + XSPI_CR_OFFSET);
258 /* ACK old irqs (if any) */
259 isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
260 if (isr)
261 xspi->write_fn(isr,
262 xspi->regs + XIPIF_V123B_IISR_OFFSET);
263 /* Enable the global IPIF interrupt */
264 xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
265 xspi->regs + XIPIF_V123B_DGIER_OFFSET);
266 reinit_completion(&xspi->done);
267 }
268
269 while (remaining_words) {
270 int n_words, tx_words, rx_words;
271 u32 sr;
272 int stalled;
273
274 n_words = min(remaining_words, xspi->buffer_size);
275
276 tx_words = n_words;
277 while (tx_words--)
278 xilinx_spi_tx(xspi);
279
280 /* Start the transfer by not inhibiting the transmitter any
281 * longer
282 */
283
284 if (use_irq) {
285 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
286 wait_for_completion(&xspi->done);
287 /* A transmit has just completed. Process received data
288 * and check for more data to transmit. Always inhibit
289 * the transmitter while the Isr refills the transmit
290 * register/FIFO, or make sure it is stopped if we're
291 * done.
292 */
293 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
294 xspi->regs + XSPI_CR_OFFSET);
295 sr = XSPI_SR_TX_EMPTY_MASK;
296 } else
297 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
298
299 /* Read out all the data from the Rx FIFO */
300 rx_words = n_words;
301 stalled = 10;
302 while (rx_words) {
303 if (rx_words == n_words && !(stalled--) &&
304 !(sr & XSPI_SR_TX_EMPTY_MASK) &&
305 (sr & XSPI_SR_RX_EMPTY_MASK)) {
306 dev_err(&spi->dev,
307 "Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n");
308 xspi_init_hw(xspi);
309 return -EIO;
310 }
311
312 if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
313 xilinx_spi_rx(xspi);
314 rx_words--;
315 continue;
316 }
317
318 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
319 if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
320 xilinx_spi_rx(xspi);
321 rx_words--;
322 }
323 }
324
325 remaining_words -= n_words;
326 }
327
328 if (use_irq) {
329 xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
330 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
331 }
332
333 return t->len;
334}
335
336
337/* This driver supports single master mode only. Hence Tx FIFO Empty
338 * is the only interrupt we care about.
339 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
340 * Fault are not to happen.
341 */
342static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
343{
344 struct xilinx_spi *xspi = dev_id;
345 u32 ipif_isr;
346
347 /* Get the IPIF interrupts, and clear them immediately */
348 ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
349 xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
350
351 if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */
352 complete(&xspi->done);
353 return IRQ_HANDLED;
354 }
355
356 return IRQ_NONE;
357}
358
359static int xilinx_spi_find_buffer_size(struct xilinx_spi *xspi)
360{
361 u8 sr;
362 int n_words = 0;
363
364 /*
365 * Before the buffer_size detection we reset the core
366 * to make sure we start with a clean state.
367 */
368 xspi->write_fn(XIPIF_V123B_RESET_MASK,
369 xspi->regs + XIPIF_V123B_RESETR_OFFSET);
370
371 /* Fill the Tx FIFO with as many words as possible */
372 do {
373 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
374 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
375 n_words++;
376 } while (!(sr & XSPI_SR_TX_FULL_MASK));
377
378 return n_words;
379}
380
381static const struct of_device_id xilinx_spi_of_match[] = {
382 { .compatible = "xlnx,axi-quad-spi-1.00.a", },
383 { .compatible = "xlnx,xps-spi-2.00.a", },
384 { .compatible = "xlnx,xps-spi-2.00.b", },
385 {}
386};
387MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
388
389static int xilinx_spi_probe(struct platform_device *pdev)
390{
391 struct xilinx_spi *xspi;
392 struct xspi_platform_data *pdata;
393 struct resource *res;
394 int ret, num_cs = 0, bits_per_word;
395 struct spi_master *master;
396 u32 tmp;
397 u8 i;
398
399 pdata = dev_get_platdata(&pdev->dev);
400 if (pdata) {
401 num_cs = pdata->num_chipselect;
402 bits_per_word = pdata->bits_per_word;
403 } else {
404 of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits",
405 &num_cs);
406 ret = of_property_read_u32(pdev->dev.of_node,
407 "xlnx,num-transfer-bits",
408 &bits_per_word);
409 if (ret)
410 bits_per_word = 8;
411 }
412
413 if (!num_cs) {
414 dev_err(&pdev->dev,
415 "Missing slave select configuration data\n");
416 return -EINVAL;
417 }
418
419 if (num_cs > XILINX_SPI_MAX_CS) {
420 dev_err(&pdev->dev, "Invalid number of spi slaves\n");
421 return -EINVAL;
422 }
423
424 master = devm_spi_alloc_master(&pdev->dev, sizeof(struct xilinx_spi));
425 if (!master)
426 return -ENODEV;
427
428 /* the spi->mode bits understood by this driver: */
429 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP |
430 SPI_CS_HIGH;
431
432 xspi = spi_master_get_devdata(master);
433 xspi->cs_inactive = 0xffffffff;
434 xspi->bitbang.master = master;
435 xspi->bitbang.chipselect = xilinx_spi_chipselect;
436 xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
437 xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
438 init_completion(&xspi->done);
439
440 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
441 xspi->regs = devm_ioremap_resource(&pdev->dev, res);
442 if (IS_ERR(xspi->regs))
443 return PTR_ERR(xspi->regs);
444
445 master->bus_num = pdev->id;
446 master->num_chipselect = num_cs;
447 master->dev.of_node = pdev->dev.of_node;
448
449 /*
450 * Detect endianess on the IP via loop bit in CR. Detection
451 * must be done before reset is sent because incorrect reset
452 * value generates error interrupt.
453 * Setup little endian helper functions first and try to use them
454 * and check if bit was correctly setup or not.
455 */
456 xspi->read_fn = xspi_read32;
457 xspi->write_fn = xspi_write32;
458
459 xspi->write_fn(XSPI_CR_LOOP, xspi->regs + XSPI_CR_OFFSET);
460 tmp = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
461 tmp &= XSPI_CR_LOOP;
462 if (tmp != XSPI_CR_LOOP) {
463 xspi->read_fn = xspi_read32_be;
464 xspi->write_fn = xspi_write32_be;
465 }
466
467 master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word);
468 xspi->bytes_per_word = bits_per_word / 8;
469 xspi->buffer_size = xilinx_spi_find_buffer_size(xspi);
470
471 xspi->irq = platform_get_irq(pdev, 0);
472 if (xspi->irq < 0 && xspi->irq != -ENXIO) {
473 return xspi->irq;
474 } else if (xspi->irq >= 0) {
475 /* Register for SPI Interrupt */
476 ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0,
477 dev_name(&pdev->dev), xspi);
478 if (ret)
479 return ret;
480 }
481
482 /* SPI controller initializations */
483 xspi_init_hw(xspi);
484
485 ret = spi_bitbang_start(&xspi->bitbang);
486 if (ret) {
487 dev_err(&pdev->dev, "spi_bitbang_start FAILED\n");
488 return ret;
489 }
490
491 dev_info(&pdev->dev, "at %pR, irq=%d\n", res, xspi->irq);
492
493 if (pdata) {
494 for (i = 0; i < pdata->num_devices; i++)
495 spi_new_device(master, pdata->devices + i);
496 }
497
498 platform_set_drvdata(pdev, master);
499 return 0;
500}
501
502static int xilinx_spi_remove(struct platform_device *pdev)
503{
504 struct spi_master *master = platform_get_drvdata(pdev);
505 struct xilinx_spi *xspi = spi_master_get_devdata(master);
506 void __iomem *regs_base = xspi->regs;
507
508 spi_bitbang_stop(&xspi->bitbang);
509
510 /* Disable all the interrupts just in case */
511 xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
512 /* Disable the global IPIF interrupt */
513 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
514
515 spi_master_put(xspi->bitbang.master);
516
517 return 0;
518}
519
520/* work with hotplug and coldplug */
521MODULE_ALIAS("platform:" XILINX_SPI_NAME);
522
523static struct platform_driver xilinx_spi_driver = {
524 .probe = xilinx_spi_probe,
525 .remove = xilinx_spi_remove,
526 .driver = {
527 .name = XILINX_SPI_NAME,
528 .of_match_table = xilinx_spi_of_match,
529 },
530};
531module_platform_driver(xilinx_spi_driver);
532
533MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
534MODULE_DESCRIPTION("Xilinx SPI driver");
535MODULE_LICENSE("GPL");