1# SPDX-License-Identifier: GPL-2.0-only
  2#
  3# Tulip family network device configuration
  4#
  5
  6config NET_TULIP
  7	bool "DEC - Tulip devices"
  8	depends on (PCI || EISA || CARDBUS)
  9	help
 10	  This selects the "Tulip" family of EISA/PCI network cards.
 11
 12if NET_TULIP
 13
 14config DE2104X
 15	tristate "Early DECchip Tulip (dc2104x) PCI support"
 16	depends on PCI
 17	select CRC32
 18	help
 19	  This driver is developed for the SMC EtherPower series Ethernet
 20	  cards and also works with cards based on the DECchip
 21	  21040 (Tulip series) chips.  Some LinkSys PCI cards are
 22	  of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
 23	  (smc9332dst), you can also try the driver for "Generic DECchip"
 24	  cards, below.  However, most people with a network card of this type
 25	  will say Y here.)
 26
 27	  To compile this driver as a module, choose M here. The module will
 28	  be called de2104x.
 29
 30config DE2104X_DSL
 31	int "Descriptor Skip Length in 32 bit longwords"
 32	depends on DE2104X
 33	range 0 31
 34	default 0
 35	help
 36	  Setting this value allows to align ring buffer descriptors into their
 37	  own cache lines. Value of 4 corresponds to the typical 32 byte line
 38	  (the descriptor is 16 bytes). This is necessary on systems that lack
 39	  cache coherence, an example is PowerMac 5500. Otherwise 0 is safe.
 40	  Default is 0, and range is 0 to 31.
 41
 42config TULIP
 43	tristate "DECchip Tulip (dc2114x) PCI support"
 44	depends on PCI
 45	select CRC32
 46	help
 47	  This driver is developed for the SMC EtherPower series Ethernet
 48	  cards and also works with cards based on the DECchip 
 49	  21140 (Tulip series) chips.  Some LinkSys PCI cards are
 50	  of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
 51	  (smc9332dst), you can also try the driver for "Generic DECchip"
 52	  cards, above.  However, most people with a network card of this type
 53	  will say Y here.)
 54
 55	  To compile this driver as a module, choose M here. The module will
 56	  be called tulip.
 57
 58config TULIP_MWI
 59	bool "New bus configuration"
 60	depends on TULIP
 61	help
 62	  This configures your Tulip card specifically for the card and
 63	  system cache line size type you are using.
 64
 65	  This is experimental code, not yet tested on many boards.
 66
 67	  If unsure, say N.
 68
 69config TULIP_MMIO
 70	bool "Use PCI shared mem for NIC registers"
 71	depends on TULIP
 72	help
 73	  Use PCI shared memory for the NIC registers, rather than going through
 74	  the Tulip's PIO (programmed I/O ports).  Faster, but could produce
 75	  obscure bugs if your mainboard has memory controller timing issues.
 76	  If in doubt, say N.
 77
 78config TULIP_NAPI
 79	bool "Use RX polling (NAPI)"
 80	depends on TULIP
 81	help
 82	  NAPI is a new driver API designed to reduce CPU and interrupt load
 83	  when the driver is receiving lots of packets from the card. It is
 84	  still somewhat experimental and thus not yet enabled by default.
 85
 86	  If your estimated Rx load is 10kpps or more, or if the card will be
 87	  deployed on potentially unfriendly networks (e.g. in a firewall),
 88	  then say Y here.
 89
 90	  If in doubt, say N.
 91
 92config TULIP_NAPI_HW_MITIGATION
 93	bool "Use Interrupt Mitigation"
 94	depends on TULIP_NAPI
 95	help
 96	  Use HW to reduce RX interrupts. Not strictly necessary since NAPI
 97	  reduces RX interrupts by itself. Interrupt mitigation reduces RX
 98	  interrupts even at low levels of traffic at the cost of a small
 99	  latency.
100
101	  If in doubt, say Y.
102
103config TULIP_DM910X
104	def_bool y
105	depends on TULIP && SPARC
106
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
107config WINBOND_840
108	tristate "Winbond W89c840 Ethernet support"
109	depends on PCI
110	select CRC32
111	select MII
112	help
113	  This driver is for the Winbond W89c840 chip.  It also works with 
114	  the TX9882 chip on the Compex RL100-ATX board.
115	  More specific information and updates are available from
116	  <http://www.scyld.com/network/drivers.html>.
117
118config DM9102
119	tristate "Davicom DM910x/DM980x support"
120	depends on PCI
121	select CRC32
122	help
123	  This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
124	  Davicom (<http://www.davicom.com.tw/>).  If you have such a network
125	  (Ethernet) card, say Y.  Some information is contained in the file
126	  <file:Documentation/networking/device_drivers/ethernet/dec/dmfe.rst>.
127
128	  To compile this driver as a module, choose M here. The module will
129	  be called dmfe.
130
131config ULI526X
132	tristate "ULi M526x controller support"
133	depends on PCI
134	select CRC32
135	help
136	  This driver is for ULi M5261/M5263 10/100M Ethernet Controller
137	  (<http://www.nvidia.com/page/uli_drivers.html>).
138
139	  To compile this driver as a module, choose M here. The module will
140	  be called uli526x.
141	  
142config PCMCIA_XIRCOM
143	tristate "Xircom CardBus support"
144	depends on CARDBUS
145	help
146	  This driver is for the Digital "Tulip" Ethernet CardBus adapters.
147	  It should work with most DEC 21*4*-based chips/ethercards, as well
148	  as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
149	  ASIX.
150
151	  To compile this driver as a module, choose M here. The module will
152	  be called xircom_cb.  If unsure, say N.
153
154endif # NET_TULIP

  1# SPDX-License-Identifier: GPL-2.0-only
  2#
  3# Tulip family network device configuration
  4#
  5
  6config NET_TULIP
  7	bool "DEC - Tulip devices"
  8	depends on (PCI || EISA || CARDBUS)
  9	help
 10	  This selects the "Tulip" family of EISA/PCI network cards.
 11
 12if NET_TULIP
 13
 14config DE2104X
 15	tristate "Early DECchip Tulip (dc2104x) PCI support"
 16	depends on PCI
 17	select CRC32
 18	help
 19	  This driver is developed for the SMC EtherPower series Ethernet
 20	  cards and also works with cards based on the DECchip
 21	  21040 (Tulip series) chips.  Some LinkSys PCI cards are
 22	  of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
 23	  (smc9332dst), you can also try the driver for "Generic DECchip"
 24	  cards, below.  However, most people with a network card of this type
 25	  will say Y here.)
 26
 27	  To compile this driver as a module, choose M here. The module will
 28	  be called de2104x.
 29
 30config DE2104X_DSL
 31	int "Descriptor Skip Length in 32 bit longwords"
 32	depends on DE2104X
 33	range 0 31
 34	default 0
 35	help
 36	  Setting this value allows to align ring buffer descriptors into their
 37	  own cache lines. Value of 4 corresponds to the typical 32 byte line
 38	  (the descriptor is 16 bytes). This is necessary on systems that lack
 39	  cache coherence, an example is PowerMac 5500. Otherwise 0 is safe.
 40	  Default is 0, and range is 0 to 31.
 41
 42config TULIP
 43	tristate "DECchip Tulip (dc2114x) PCI support"
 44	depends on PCI
 45	select CRC32
 46	help
 47	  This driver is developed for the SMC EtherPower series Ethernet
 48	  cards and also works with cards based on the DECchip 
 49	  21140 (Tulip series) chips.  Some LinkSys PCI cards are
 50	  of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
 51	  (smc9332dst), you can also try the driver for "Generic DECchip"
 52	  cards, above.  However, most people with a network card of this type
 53	  will say Y here.)
 54
 55	  To compile this driver as a module, choose M here. The module will
 56	  be called tulip.
 57
 58config TULIP_MWI
 59	bool "New bus configuration"
 60	depends on TULIP
 61	help
 62	  This configures your Tulip card specifically for the card and
 63	  system cache line size type you are using.
 64
 65	  This is experimental code, not yet tested on many boards.
 66
 67	  If unsure, say N.
 68
 69config TULIP_MMIO
 70	bool "Use PCI shared mem for NIC registers"
 71	depends on TULIP
 72	help
 73	  Use PCI shared memory for the NIC registers, rather than going through
 74	  the Tulip's PIO (programmed I/O ports).  Faster, but could produce
 75	  obscure bugs if your mainboard has memory controller timing issues.
 76	  If in doubt, say N.
 77
 78config TULIP_NAPI
 79	bool "Use RX polling (NAPI)"
 80	depends on TULIP
 81	help
 82	  NAPI is a new driver API designed to reduce CPU and interrupt load
 83	  when the driver is receiving lots of packets from the card. It is
 84	  still somewhat experimental and thus not yet enabled by default.
 85
 86	  If your estimated Rx load is 10kpps or more, or if the card will be
 87	  deployed on potentially unfriendly networks (e.g. in a firewall),
 88	  then say Y here.
 89
 90	  If in doubt, say N.
 91
 92config TULIP_NAPI_HW_MITIGATION
 93	bool "Use Interrupt Mitigation"
 94	depends on TULIP_NAPI
 95	help
 96	  Use HW to reduce RX interrupts. Not strictly necessary since NAPI
 97	  reduces RX interrupts by itself. Interrupt mitigation reduces RX
 98	  interrupts even at low levels of traffic at the cost of a small
 99	  latency.
100
101	  If in doubt, say Y.
102
103config TULIP_DM910X
104	def_bool y
105	depends on TULIP && SPARC
106
107config DE4X5
108	tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
109	depends on (PCI || EISA)
110	depends on VIRT_TO_BUS || ALPHA || PPC || SPARC
111	select CRC32
112	help
113	  This is support for the DIGITAL series of PCI/EISA Ethernet cards.
114	  These include the DE425, DE434, DE435, DE450 and DE500 models.  If
115	  you have a network card of this type, say Y.  More specific
116	  information is contained in
117	  <file:Documentation/networking/device_drivers/ethernet/dec/de4x5.rst>.
118
119	  To compile this driver as a module, choose M here. The module will
120	  be called de4x5.
121
122config WINBOND_840
123	tristate "Winbond W89c840 Ethernet support"
124	depends on PCI
125	select CRC32
126	select MII
127	help
128	  This driver is for the Winbond W89c840 chip.  It also works with 
129	  the TX9882 chip on the Compex RL100-ATX board.
130	  More specific information and updates are available from
131	  <http://www.scyld.com/network/drivers.html>.
132
133config DM9102
134	tristate "Davicom DM910x/DM980x support"
135	depends on PCI
136	select CRC32
137	help
138	  This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
139	  Davicom (<http://www.davicom.com.tw/>).  If you have such a network
140	  (Ethernet) card, say Y.  Some information is contained in the file
141	  <file:Documentation/networking/device_drivers/ethernet/dec/dmfe.rst>.
142
143	  To compile this driver as a module, choose M here. The module will
144	  be called dmfe.
145
146config ULI526X
147	tristate "ULi M526x controller support"
148	depends on PCI
149	select CRC32
150	help
151	  This driver is for ULi M5261/M5263 10/100M Ethernet Controller
152	  (<http://www.nvidia.com/page/uli_drivers.html>).
153
154	  To compile this driver as a module, choose M here. The module will
155	  be called uli526x.
156	  
157config PCMCIA_XIRCOM
158	tristate "Xircom CardBus support"
159	depends on CARDBUS
160	help
161	  This driver is for the Digital "Tulip" Ethernet CardBus adapters.
162	  It should work with most DEC 21*4*-based chips/ethercards, as well
163	  as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
164	  ASIX.
165
166	  To compile this driver as a module, choose M here. The module will
167	  be called xircom_cb.  If unsure, say N.
168
169endif # NET_TULIP