Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
4 * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
5 * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
6 * Copyright (C) 2023 EMS Dr. Thomas Wuensche
7 */
8
9#include <linux/kernel.h>
10#include <linux/module.h>
11#include <linux/interrupt.h>
12#include <linux/netdevice.h>
13#include <linux/delay.h>
14#include <linux/slab.h>
15#include <linux/pci.h>
16#include <linux/can/dev.h>
17#include <linux/io.h>
18
19#include "sja1000.h"
20
21#define DRV_NAME "ems_pci"
22
23MODULE_AUTHOR("Sebastian Haas <support@ems-wuensche.com>");
24MODULE_AUTHOR("Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>");
25MODULE_DESCRIPTION("Socket-CAN driver for EMS CPC-PCI/PCIe/104P CAN cards");
26MODULE_LICENSE("GPL v2");
27
28#define EMS_PCI_V1_MAX_CHAN 2
29#define EMS_PCI_V2_MAX_CHAN 4
30#define EMS_PCI_V3_MAX_CHAN 4
31#define EMS_PCI_MAX_CHAN EMS_PCI_V2_MAX_CHAN
32
33struct ems_pci_card {
34 int version;
35 int channels;
36
37 struct pci_dev *pci_dev;
38 struct net_device *net_dev[EMS_PCI_MAX_CHAN];
39
40 void __iomem *conf_addr;
41 void __iomem *base_addr;
42};
43
44#define EMS_PCI_CAN_CLOCK (16000000 / 2)
45
46/* Register definitions and descriptions are from LinCAN 0.3.3.
47 *
48 * PSB4610 PITA-2 bridge control registers
49 */
50#define PITA2_ICR 0x00 /* Interrupt Control Register */
51#define PITA2_ICR_INT0 0x00000002 /* [RC] INT0 Active/Clear */
52#define PITA2_ICR_INT0_EN 0x00020000 /* [RW] Enable INT0 */
53
54#define PITA2_MISC 0x1c /* Miscellaneous Register */
55#define PITA2_MISC_CONFIG 0x04000000 /* Multiplexed parallel interface */
56
57/* Register definitions for the PLX 9030
58 */
59#define PLX_ICSR 0x4c /* Interrupt Control/Status register */
60#define PLX_ICSR_LINTI1_ENA 0x0001 /* LINTi1 Enable */
61#define PLX_ICSR_PCIINT_ENA 0x0040 /* PCI Interrupt Enable */
62#define PLX_ICSR_LINTI1_CLR 0x0400 /* Local Edge Triggerable Interrupt Clear */
63#define PLX_ICSR_ENA_CLR (PLX_ICSR_LINTI1_ENA | PLX_ICSR_PCIINT_ENA | \
64 PLX_ICSR_LINTI1_CLR)
65
66/* Register definitions for the ASIX99100
67 */
68#define ASIX_LINTSR 0x28 /* Interrupt Control/Status register */
69#define ASIX_LINTSR_INT0AC BIT(0) /* Writing 1 enables or clears interrupt */
70
71#define ASIX_LIEMR 0x24 /* Local Interrupt Enable / Miscellaneous Register */
72#define ASIX_LIEMR_L0EINTEN BIT(16) /* Local INT0 input assertion enable */
73#define ASIX_LIEMR_LRST BIT(14) /* Local Reset assert */
74
75/* The board configuration is probably following:
76 * RX1 is connected to ground.
77 * TX1 is not connected.
78 * CLKO is not connected.
79 * Setting the OCR register to 0xDA is a good idea.
80 * This means normal output mode, push-pull and the correct polarity.
81 */
82#define EMS_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
83
84/* In the CDR register, you should set CBP to 1.
85 * You will probably also want to set the clock divider value to 7
86 * (meaning direct oscillator output) because the second SJA1000 chip
87 * is driven by the first one CLKOUT output.
88 */
89#define EMS_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
90
91#define EMS_PCI_V1_BASE_BAR 1
92#define EMS_PCI_V1_CONF_BAR 0
93#define EMS_PCI_V1_CONF_SIZE 4096 /* size of PITA control area */
94#define EMS_PCI_V1_CAN_BASE_OFFSET 0x400 /* offset where the controllers start */
95#define EMS_PCI_V1_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
96
97#define EMS_PCI_V2_BASE_BAR 2
98#define EMS_PCI_V2_CONF_BAR 0
99#define EMS_PCI_V2_CONF_SIZE 128 /* size of PLX control area */
100#define EMS_PCI_V2_CAN_BASE_OFFSET 0x400 /* offset where the controllers start */
101#define EMS_PCI_V2_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
102
103#define EMS_PCI_V3_BASE_BAR 0
104#define EMS_PCI_V3_CONF_BAR 5
105#define EMS_PCI_V3_CONF_SIZE 128 /* size of ASIX control area */
106#define EMS_PCI_V3_CAN_BASE_OFFSET 0x00 /* offset where the controllers starts */
107#define EMS_PCI_V3_CAN_CTRL_SIZE 0x100 /* memory size for each controller */
108
109#define EMS_PCI_BASE_SIZE 4096 /* size of controller area */
110
111#define PCI_SUBDEVICE_ID_EMS 0x4010
112
113static const struct pci_device_id ems_pci_tbl[] = {
114 /* CPC-PCI v1 */
115 {PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,},
116 /* CPC-PCI v2 */
117 {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4000},
118 /* CPC-104P v2 */
119 {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4002},
120 /* CPC-PCIe v3 */
121 {PCI_VENDOR_ID_ASIX, PCI_DEVICE_ID_ASIX_AX99100_LB, 0xa000, PCI_SUBDEVICE_ID_EMS},
122 {0,}
123};
124MODULE_DEVICE_TABLE(pci, ems_pci_tbl);
125
126/* Helper to read internal registers from card logic (not CAN)
127 */
128static u8 ems_pci_v1_readb(struct ems_pci_card *card, unsigned int port)
129{
130 return readb(card->base_addr + (port * 4));
131}
132
133static u8 ems_pci_v1_read_reg(const struct sja1000_priv *priv, int port)
134{
135 return readb(priv->reg_base + (port * 4));
136}
137
138static void ems_pci_v1_write_reg(const struct sja1000_priv *priv,
139 int port, u8 val)
140{
141 writeb(val, priv->reg_base + (port * 4));
142}
143
144static void ems_pci_v1_post_irq(const struct sja1000_priv *priv)
145{
146 struct ems_pci_card *card = priv->priv;
147
148 /* reset int flag of pita */
149 writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
150 card->conf_addr + PITA2_ICR);
151}
152
153static u8 ems_pci_v2_read_reg(const struct sja1000_priv *priv, int port)
154{
155 return readb(priv->reg_base + port);
156}
157
158static void ems_pci_v2_write_reg(const struct sja1000_priv *priv,
159 int port, u8 val)
160{
161 writeb(val, priv->reg_base + port);
162}
163
164static void ems_pci_v2_post_irq(const struct sja1000_priv *priv)
165{
166 struct ems_pci_card *card = priv->priv;
167
168 writel(PLX_ICSR_ENA_CLR, card->conf_addr + PLX_ICSR);
169}
170
171static u8 ems_pci_v3_read_reg(const struct sja1000_priv *priv, int port)
172{
173 return readb(priv->reg_base + port);
174}
175
176static void ems_pci_v3_write_reg(const struct sja1000_priv *priv,
177 int port, u8 val)
178{
179 writeb(val, priv->reg_base + port);
180}
181
182static void ems_pci_v3_post_irq(const struct sja1000_priv *priv)
183{
184 struct ems_pci_card *card = priv->priv;
185
186 writel(ASIX_LINTSR_INT0AC, card->conf_addr + ASIX_LINTSR);
187}
188
189/* Check if a CAN controller is present at the specified location
190 * by trying to set 'em into the PeliCAN mode
191 */
192static inline int ems_pci_check_chan(const struct sja1000_priv *priv)
193{
194 unsigned char res;
195
196 /* Make sure SJA1000 is in reset mode */
197 priv->write_reg(priv, SJA1000_MOD, 1);
198
199 priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
200
201 /* read reset-values */
202 res = priv->read_reg(priv, SJA1000_CDR);
203
204 if (res == CDR_PELICAN)
205 return 1;
206
207 return 0;
208}
209
210static void ems_pci_del_card(struct pci_dev *pdev)
211{
212 struct ems_pci_card *card = pci_get_drvdata(pdev);
213 struct net_device *dev;
214 int i = 0;
215
216 for (i = 0; i < card->channels; i++) {
217 dev = card->net_dev[i];
218
219 if (!dev)
220 continue;
221
222 dev_info(&pdev->dev, "Removing %s.\n", dev->name);
223 unregister_sja1000dev(dev);
224 free_sja1000dev(dev);
225 }
226
227 if (card->base_addr)
228 pci_iounmap(card->pci_dev, card->base_addr);
229
230 if (card->conf_addr)
231 pci_iounmap(card->pci_dev, card->conf_addr);
232
233 kfree(card);
234
235 pci_disable_device(pdev);
236}
237
238static void ems_pci_card_reset(struct ems_pci_card *card)
239{
240 /* Request board reset */
241 writeb(0, card->base_addr);
242}
243
244/* Probe PCI device for EMS CAN signature and register each available
245 * CAN channel to SJA1000 Socket-CAN subsystem.
246 */
247static int ems_pci_add_card(struct pci_dev *pdev,
248 const struct pci_device_id *ent)
249{
250 struct sja1000_priv *priv;
251 struct net_device *dev;
252 struct ems_pci_card *card;
253 int max_chan, conf_size, base_bar, conf_bar;
254 int err, i;
255
256 /* Enabling PCI device */
257 if (pci_enable_device(pdev) < 0) {
258 dev_err(&pdev->dev, "Enabling PCI device failed\n");
259 return -ENODEV;
260 }
261
262 /* Allocating card structures to hold addresses, ... */
263 card = kzalloc(sizeof(*card), GFP_KERNEL);
264 if (!card) {
265 pci_disable_device(pdev);
266 return -ENOMEM;
267 }
268
269 pci_set_drvdata(pdev, card);
270
271 card->pci_dev = pdev;
272
273 card->channels = 0;
274
275 if (pdev->vendor == PCI_VENDOR_ID_ASIX) {
276 card->version = 3; /* CPC-PCI v3 */
277 max_chan = EMS_PCI_V3_MAX_CHAN;
278 base_bar = EMS_PCI_V3_BASE_BAR;
279 conf_bar = EMS_PCI_V3_CONF_BAR;
280 conf_size = EMS_PCI_V3_CONF_SIZE;
281 } else if (pdev->vendor == PCI_VENDOR_ID_PLX) {
282 card->version = 2; /* CPC-PCI v2 */
283 max_chan = EMS_PCI_V2_MAX_CHAN;
284 base_bar = EMS_PCI_V2_BASE_BAR;
285 conf_bar = EMS_PCI_V2_CONF_BAR;
286 conf_size = EMS_PCI_V2_CONF_SIZE;
287 } else {
288 card->version = 1; /* CPC-PCI v1 */
289 max_chan = EMS_PCI_V1_MAX_CHAN;
290 base_bar = EMS_PCI_V1_BASE_BAR;
291 conf_bar = EMS_PCI_V1_CONF_BAR;
292 conf_size = EMS_PCI_V1_CONF_SIZE;
293 }
294
295 /* Remap configuration space and controller memory area */
296 card->conf_addr = pci_iomap(pdev, conf_bar, conf_size);
297 if (!card->conf_addr) {
298 err = -ENOMEM;
299 goto failure_cleanup;
300 }
301
302 card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE);
303 if (!card->base_addr) {
304 err = -ENOMEM;
305 goto failure_cleanup;
306 }
307
308 if (card->version == 1) {
309 /* Configure PITA-2 parallel interface (enable MUX) */
310 writel(PITA2_MISC_CONFIG, card->conf_addr + PITA2_MISC);
311
312 /* Check for unique EMS CAN signature */
313 if (ems_pci_v1_readb(card, 0) != 0x55 ||
314 ems_pci_v1_readb(card, 1) != 0xAA ||
315 ems_pci_v1_readb(card, 2) != 0x01 ||
316 ems_pci_v1_readb(card, 3) != 0xCB ||
317 ems_pci_v1_readb(card, 4) != 0x11) {
318 dev_err(&pdev->dev,
319 "Not EMS Dr. Thomas Wuensche interface\n");
320 err = -ENODEV;
321 goto failure_cleanup;
322 }
323 }
324
325 if (card->version == 3) {
326 /* ASIX chip asserts local reset to CAN controllers
327 * after bootup until it is deasserted
328 */
329 writel(readl(card->conf_addr + ASIX_LIEMR) & ~ASIX_LIEMR_LRST,
330 card->conf_addr + ASIX_LIEMR);
331 }
332
333 ems_pci_card_reset(card);
334
335 /* Detect available channels */
336 for (i = 0; i < max_chan; i++) {
337 dev = alloc_sja1000dev(0);
338 if (!dev) {
339 err = -ENOMEM;
340 goto failure_cleanup;
341 }
342
343 card->net_dev[i] = dev;
344 priv = netdev_priv(dev);
345 priv->priv = card;
346 priv->irq_flags = IRQF_SHARED;
347
348 dev->irq = pdev->irq;
349
350 if (card->version == 1) {
351 priv->read_reg = ems_pci_v1_read_reg;
352 priv->write_reg = ems_pci_v1_write_reg;
353 priv->post_irq = ems_pci_v1_post_irq;
354 priv->reg_base = card->base_addr + EMS_PCI_V1_CAN_BASE_OFFSET
355 + (i * EMS_PCI_V1_CAN_CTRL_SIZE);
356 } else if (card->version == 2) {
357 priv->read_reg = ems_pci_v2_read_reg;
358 priv->write_reg = ems_pci_v2_write_reg;
359 priv->post_irq = ems_pci_v2_post_irq;
360 priv->reg_base = card->base_addr + EMS_PCI_V2_CAN_BASE_OFFSET
361 + (i * EMS_PCI_V2_CAN_CTRL_SIZE);
362 } else {
363 priv->read_reg = ems_pci_v3_read_reg;
364 priv->write_reg = ems_pci_v3_write_reg;
365 priv->post_irq = ems_pci_v3_post_irq;
366 priv->reg_base = card->base_addr + EMS_PCI_V3_CAN_BASE_OFFSET
367 + (i * EMS_PCI_V3_CAN_CTRL_SIZE);
368 }
369
370 /* Check if channel is present */
371 if (ems_pci_check_chan(priv)) {
372 priv->can.clock.freq = EMS_PCI_CAN_CLOCK;
373 priv->ocr = EMS_PCI_OCR;
374 priv->cdr = EMS_PCI_CDR;
375
376 SET_NETDEV_DEV(dev, &pdev->dev);
377 dev->dev_id = i;
378
379 if (card->version == 1) {
380 /* reset int flag of pita */
381 writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
382 card->conf_addr + PITA2_ICR);
383 } else if (card->version == 2) {
384 /* enable IRQ in PLX 9030 */
385 writel(PLX_ICSR_ENA_CLR,
386 card->conf_addr + PLX_ICSR);
387 } else {
388 /* Enable IRQ in AX99100 */
389 writel(ASIX_LINTSR_INT0AC, card->conf_addr + ASIX_LINTSR);
390 /* Enable local INT0 input enable */
391 writel(readl(card->conf_addr + ASIX_LIEMR) | ASIX_LIEMR_L0EINTEN,
392 card->conf_addr + ASIX_LIEMR);
393 }
394
395 /* Register SJA1000 device */
396 err = register_sja1000dev(dev);
397 if (err) {
398 dev_err(&pdev->dev,
399 "Registering device failed: %pe\n",
400 ERR_PTR(err));
401 free_sja1000dev(dev);
402 goto failure_cleanup;
403 }
404
405 card->channels++;
406
407 dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d\n",
408 i + 1, priv->reg_base, dev->irq);
409 } else {
410 free_sja1000dev(dev);
411 }
412 }
413
414 return 0;
415
416failure_cleanup:
417 dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
418
419 ems_pci_del_card(pdev);
420
421 return err;
422}
423
424static struct pci_driver ems_pci_driver = {
425 .name = DRV_NAME,
426 .id_table = ems_pci_tbl,
427 .probe = ems_pci_add_card,
428 .remove = ems_pci_del_card,
429};
430
431module_pci_driver(ems_pci_driver);
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
4 * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
5 * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
6 */
7
8#include <linux/kernel.h>
9#include <linux/module.h>
10#include <linux/interrupt.h>
11#include <linux/netdevice.h>
12#include <linux/delay.h>
13#include <linux/slab.h>
14#include <linux/pci.h>
15#include <linux/can/dev.h>
16#include <linux/io.h>
17
18#include "sja1000.h"
19
20#define DRV_NAME "ems_pci"
21
22MODULE_AUTHOR("Sebastian Haas <haas@ems-wuenche.com>");
23MODULE_DESCRIPTION("Socket-CAN driver for EMS CPC-PCI/PCIe/104P CAN cards");
24MODULE_SUPPORTED_DEVICE("EMS CPC-PCI/PCIe/104P CAN card");
25MODULE_LICENSE("GPL v2");
26
27#define EMS_PCI_V1_MAX_CHAN 2
28#define EMS_PCI_V2_MAX_CHAN 4
29#define EMS_PCI_MAX_CHAN EMS_PCI_V2_MAX_CHAN
30
31struct ems_pci_card {
32 int version;
33 int channels;
34
35 struct pci_dev *pci_dev;
36 struct net_device *net_dev[EMS_PCI_MAX_CHAN];
37
38 void __iomem *conf_addr;
39 void __iomem *base_addr;
40};
41
42#define EMS_PCI_CAN_CLOCK (16000000 / 2)
43
44/*
45 * Register definitions and descriptions are from LinCAN 0.3.3.
46 *
47 * PSB4610 PITA-2 bridge control registers
48 */
49#define PITA2_ICR 0x00 /* Interrupt Control Register */
50#define PITA2_ICR_INT0 0x00000002 /* [RC] INT0 Active/Clear */
51#define PITA2_ICR_INT0_EN 0x00020000 /* [RW] Enable INT0 */
52
53#define PITA2_MISC 0x1c /* Miscellaneous Register */
54#define PITA2_MISC_CONFIG 0x04000000 /* Multiplexed parallel interface */
55
56/*
57 * Register definitions for the PLX 9030
58 */
59#define PLX_ICSR 0x4c /* Interrupt Control/Status register */
60#define PLX_ICSR_LINTI1_ENA 0x0001 /* LINTi1 Enable */
61#define PLX_ICSR_PCIINT_ENA 0x0040 /* PCI Interrupt Enable */
62#define PLX_ICSR_LINTI1_CLR 0x0400 /* Local Edge Triggerable Interrupt Clear */
63#define PLX_ICSR_ENA_CLR (PLX_ICSR_LINTI1_ENA | PLX_ICSR_PCIINT_ENA | \
64 PLX_ICSR_LINTI1_CLR)
65
66/*
67 * The board configuration is probably following:
68 * RX1 is connected to ground.
69 * TX1 is not connected.
70 * CLKO is not connected.
71 * Setting the OCR register to 0xDA is a good idea.
72 * This means normal output mode, push-pull and the correct polarity.
73 */
74#define EMS_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
75
76/*
77 * In the CDR register, you should set CBP to 1.
78 * You will probably also want to set the clock divider value to 7
79 * (meaning direct oscillator output) because the second SJA1000 chip
80 * is driven by the first one CLKOUT output.
81 */
82#define EMS_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
83
84#define EMS_PCI_V1_BASE_BAR 1
85#define EMS_PCI_V1_CONF_SIZE 4096 /* size of PITA control area */
86#define EMS_PCI_V2_BASE_BAR 2
87#define EMS_PCI_V2_CONF_SIZE 128 /* size of PLX control area */
88#define EMS_PCI_CAN_BASE_OFFSET 0x400 /* offset where the controllers starts */
89#define EMS_PCI_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
90
91#define EMS_PCI_BASE_SIZE 4096 /* size of controller area */
92
93static const struct pci_device_id ems_pci_tbl[] = {
94 /* CPC-PCI v1 */
95 {PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,},
96 /* CPC-PCI v2 */
97 {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4000},
98 /* CPC-104P v2 */
99 {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4002},
100 {0,}
101};
102MODULE_DEVICE_TABLE(pci, ems_pci_tbl);
103
104/*
105 * Helper to read internal registers from card logic (not CAN)
106 */
107static u8 ems_pci_v1_readb(struct ems_pci_card *card, unsigned int port)
108{
109 return readb(card->base_addr + (port * 4));
110}
111
112static u8 ems_pci_v1_read_reg(const struct sja1000_priv *priv, int port)
113{
114 return readb(priv->reg_base + (port * 4));
115}
116
117static void ems_pci_v1_write_reg(const struct sja1000_priv *priv,
118 int port, u8 val)
119{
120 writeb(val, priv->reg_base + (port * 4));
121}
122
123static void ems_pci_v1_post_irq(const struct sja1000_priv *priv)
124{
125 struct ems_pci_card *card = (struct ems_pci_card *)priv->priv;
126
127 /* reset int flag of pita */
128 writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
129 card->conf_addr + PITA2_ICR);
130}
131
132static u8 ems_pci_v2_read_reg(const struct sja1000_priv *priv, int port)
133{
134 return readb(priv->reg_base + port);
135}
136
137static void ems_pci_v2_write_reg(const struct sja1000_priv *priv,
138 int port, u8 val)
139{
140 writeb(val, priv->reg_base + port);
141}
142
143static void ems_pci_v2_post_irq(const struct sja1000_priv *priv)
144{
145 struct ems_pci_card *card = (struct ems_pci_card *)priv->priv;
146
147 writel(PLX_ICSR_ENA_CLR, card->conf_addr + PLX_ICSR);
148}
149
150/*
151 * Check if a CAN controller is present at the specified location
152 * by trying to set 'em into the PeliCAN mode
153 */
154static inline int ems_pci_check_chan(const struct sja1000_priv *priv)
155{
156 unsigned char res;
157
158 /* Make sure SJA1000 is in reset mode */
159 priv->write_reg(priv, SJA1000_MOD, 1);
160
161 priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
162
163 /* read reset-values */
164 res = priv->read_reg(priv, SJA1000_CDR);
165
166 if (res == CDR_PELICAN)
167 return 1;
168
169 return 0;
170}
171
172static void ems_pci_del_card(struct pci_dev *pdev)
173{
174 struct ems_pci_card *card = pci_get_drvdata(pdev);
175 struct net_device *dev;
176 int i = 0;
177
178 for (i = 0; i < card->channels; i++) {
179 dev = card->net_dev[i];
180
181 if (!dev)
182 continue;
183
184 dev_info(&pdev->dev, "Removing %s.\n", dev->name);
185 unregister_sja1000dev(dev);
186 free_sja1000dev(dev);
187 }
188
189 if (card->base_addr != NULL)
190 pci_iounmap(card->pci_dev, card->base_addr);
191
192 if (card->conf_addr != NULL)
193 pci_iounmap(card->pci_dev, card->conf_addr);
194
195 kfree(card);
196
197 pci_disable_device(pdev);
198}
199
200static void ems_pci_card_reset(struct ems_pci_card *card)
201{
202 /* Request board reset */
203 writeb(0, card->base_addr);
204}
205
206/*
207 * Probe PCI device for EMS CAN signature and register each available
208 * CAN channel to SJA1000 Socket-CAN subsystem.
209 */
210static int ems_pci_add_card(struct pci_dev *pdev,
211 const struct pci_device_id *ent)
212{
213 struct sja1000_priv *priv;
214 struct net_device *dev;
215 struct ems_pci_card *card;
216 int max_chan, conf_size, base_bar;
217 int err, i;
218
219 /* Enabling PCI device */
220 if (pci_enable_device(pdev) < 0) {
221 dev_err(&pdev->dev, "Enabling PCI device failed\n");
222 return -ENODEV;
223 }
224
225 /* Allocating card structures to hold addresses, ... */
226 card = kzalloc(sizeof(struct ems_pci_card), GFP_KERNEL);
227 if (card == NULL) {
228 pci_disable_device(pdev);
229 return -ENOMEM;
230 }
231
232 pci_set_drvdata(pdev, card);
233
234 card->pci_dev = pdev;
235
236 card->channels = 0;
237
238 if (pdev->vendor == PCI_VENDOR_ID_PLX) {
239 card->version = 2; /* CPC-PCI v2 */
240 max_chan = EMS_PCI_V2_MAX_CHAN;
241 base_bar = EMS_PCI_V2_BASE_BAR;
242 conf_size = EMS_PCI_V2_CONF_SIZE;
243 } else {
244 card->version = 1; /* CPC-PCI v1 */
245 max_chan = EMS_PCI_V1_MAX_CHAN;
246 base_bar = EMS_PCI_V1_BASE_BAR;
247 conf_size = EMS_PCI_V1_CONF_SIZE;
248 }
249
250 /* Remap configuration space and controller memory area */
251 card->conf_addr = pci_iomap(pdev, 0, conf_size);
252 if (card->conf_addr == NULL) {
253 err = -ENOMEM;
254 goto failure_cleanup;
255 }
256
257 card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE);
258 if (card->base_addr == NULL) {
259 err = -ENOMEM;
260 goto failure_cleanup;
261 }
262
263 if (card->version == 1) {
264 /* Configure PITA-2 parallel interface (enable MUX) */
265 writel(PITA2_MISC_CONFIG, card->conf_addr + PITA2_MISC);
266
267 /* Check for unique EMS CAN signature */
268 if (ems_pci_v1_readb(card, 0) != 0x55 ||
269 ems_pci_v1_readb(card, 1) != 0xAA ||
270 ems_pci_v1_readb(card, 2) != 0x01 ||
271 ems_pci_v1_readb(card, 3) != 0xCB ||
272 ems_pci_v1_readb(card, 4) != 0x11) {
273 dev_err(&pdev->dev,
274 "Not EMS Dr. Thomas Wuensche interface\n");
275 err = -ENODEV;
276 goto failure_cleanup;
277 }
278 }
279
280 ems_pci_card_reset(card);
281
282 /* Detect available channels */
283 for (i = 0; i < max_chan; i++) {
284 dev = alloc_sja1000dev(0);
285 if (dev == NULL) {
286 err = -ENOMEM;
287 goto failure_cleanup;
288 }
289
290 card->net_dev[i] = dev;
291 priv = netdev_priv(dev);
292 priv->priv = card;
293 priv->irq_flags = IRQF_SHARED;
294
295 dev->irq = pdev->irq;
296 priv->reg_base = card->base_addr + EMS_PCI_CAN_BASE_OFFSET
297 + (i * EMS_PCI_CAN_CTRL_SIZE);
298 if (card->version == 1) {
299 priv->read_reg = ems_pci_v1_read_reg;
300 priv->write_reg = ems_pci_v1_write_reg;
301 priv->post_irq = ems_pci_v1_post_irq;
302 } else {
303 priv->read_reg = ems_pci_v2_read_reg;
304 priv->write_reg = ems_pci_v2_write_reg;
305 priv->post_irq = ems_pci_v2_post_irq;
306 }
307
308 /* Check if channel is present */
309 if (ems_pci_check_chan(priv)) {
310 priv->can.clock.freq = EMS_PCI_CAN_CLOCK;
311 priv->ocr = EMS_PCI_OCR;
312 priv->cdr = EMS_PCI_CDR;
313
314 SET_NETDEV_DEV(dev, &pdev->dev);
315 dev->dev_id = i;
316
317 if (card->version == 1)
318 /* reset int flag of pita */
319 writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
320 card->conf_addr + PITA2_ICR);
321 else
322 /* enable IRQ in PLX 9030 */
323 writel(PLX_ICSR_ENA_CLR,
324 card->conf_addr + PLX_ICSR);
325
326 /* Register SJA1000 device */
327 err = register_sja1000dev(dev);
328 if (err) {
329 dev_err(&pdev->dev, "Registering device failed "
330 "(err=%d)\n", err);
331 free_sja1000dev(dev);
332 goto failure_cleanup;
333 }
334
335 card->channels++;
336
337 dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d\n",
338 i + 1, priv->reg_base, dev->irq);
339 } else {
340 free_sja1000dev(dev);
341 }
342 }
343
344 return 0;
345
346failure_cleanup:
347 dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
348
349 ems_pci_del_card(pdev);
350
351 return err;
352}
353
354static struct pci_driver ems_pci_driver = {
355 .name = DRV_NAME,
356 .id_table = ems_pci_tbl,
357 .probe = ems_pci_add_card,
358 .remove = ems_pci_del_card,
359};
360
361module_pci_driver(ems_pci_driver);