Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# PHY Layer Configuration
4#
5
6config PHYLINK
7 tristate
8 depends on NETDEVICES
9 select PHYLIB
10 select SWPHY
11 help
12 PHYlink models the link between the PHY and MAC, allowing fixed
13 configuration links, PHYs, and Serdes links with MAC level
14 autonegotiation modes.
15
16menuconfig PHYLIB
17 tristate "PHY Device support and infrastructure"
18 depends on NETDEVICES
19 select MDIO_DEVICE
20 select MDIO_DEVRES
21 help
22 Ethernet controllers are usually attached to PHY
23 devices. This option provides infrastructure for
24 managing PHY devices.
25
26if PHYLIB
27
28config SWPHY
29 bool
30
31config LED_TRIGGER_PHY
32 bool "Support LED triggers for tracking link state"
33 depends on LEDS_TRIGGERS
34 help
35 Adds support for a set of LED trigger events per-PHY. Link
36 state change will trigger the events, for consumption by an
37 LED class driver. There are triggers for each link speed currently
38 supported by the PHY and also a one common "link" trigger as a
39 logical-or of all the link speed ones.
40 All these triggers are named according to the following pattern:
41 <mii bus id>:<phy>:<speed>
42
43 Where speed is in the form:
44 <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link
45 for any speed known to the PHY.
46
47config PHYLIB_LEDS
48 def_bool OF
49 depends on LEDS_CLASS=y || LEDS_CLASS=PHYLIB
50 help
51 When LED class support is enabled, phylib can automatically
52 probe LED setting from device tree.
53
54config FIXED_PHY
55 tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
56 select SWPHY
57 help
58 Adds the platform "fixed" MDIO Bus to cover the boards that use
59 PHYs that are not connected to the real MDIO bus.
60
61 Currently tested with mpc866ads and mpc8349e-mitx.
62
63config RUST_PHYLIB_ABSTRACTIONS
64 bool "Rust PHYLIB abstractions support"
65 depends on RUST
66 depends on PHYLIB=y
67 help
68 Adds support needed for PHY drivers written in Rust. It provides
69 a wrapper around the C phylib core.
70
71config SFP
72 tristate "SFP cage support"
73 depends on I2C && PHYLINK
74 depends on HWMON || HWMON=n
75 select MDIO_I2C
76
77comment "MII PHY device drivers"
78
79config AMD_PHY
80 tristate "AMD and Altima PHYs"
81 help
82 Currently supports the AMD am79c874 and Altima AC101L.
83
84config MESON_GXL_PHY
85 tristate "Amlogic Meson GXL Internal PHY"
86 depends on ARCH_MESON || COMPILE_TEST
87 select SMSC_PHY
88 help
89 Currently has a driver for the Amlogic Meson GXL Internal PHY
90
91config ADIN_PHY
92 tristate "Analog Devices Industrial Ethernet PHYs"
93 help
94 Adds support for the Analog Devices Industrial Ethernet PHYs.
95 Currently supports the:
96 - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY
97 - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
98 Ethernet PHY
99
100config ADIN1100_PHY
101 tristate "Analog Devices Industrial Ethernet T1L PHYs"
102 help
103 Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
104 Currently supports the:
105 - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
106
107source "drivers/net/phy/aquantia/Kconfig"
108
109config AX88796B_PHY
110 tristate "Asix PHYs"
111 help
112 Currently supports the Asix Electronics PHY found in the X-Surf 100
113 AX88796B package.
114
115config AX88796B_RUST_PHY
116 bool "Rust reference driver for Asix PHYs"
117 depends on RUST_PHYLIB_ABSTRACTIONS && AX88796B_PHY
118 help
119 Uses the Rust reference driver for Asix PHYs (ax88796b_rust.ko).
120 The features are equivalent. It supports the Asix Electronics PHY
121 found in the X-Surf 100 AX88796B package.
122
123config BROADCOM_PHY
124 tristate "Broadcom 54XX PHYs"
125 select BCM_NET_PHYLIB
126 select BCM_NET_PHYPTP if NETWORK_PHY_TIMESTAMPING
127 depends on PTP_1588_CLOCK_OPTIONAL
128 help
129 Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
130 BCM5481, BCM54810 and BCM5482 PHYs.
131
132config BCM54140_PHY
133 tristate "Broadcom BCM54140 PHY"
134 depends on HWMON || HWMON=n
135 select BCM_NET_PHYLIB
136 help
137 Support the Broadcom BCM54140 Quad SGMII/QSGMII PHY.
138
139 This driver also supports the hardware monitoring of this PHY and
140 exposes voltage and temperature sensors.
141
142config BCM63XX_PHY
143 tristate "Broadcom 63xx SOCs internal PHY"
144 depends on BCM63XX || COMPILE_TEST
145 select BCM_NET_PHYLIB
146 help
147 Currently supports the 6348 and 6358 PHYs.
148
149config BCM7XXX_PHY
150 tristate "Broadcom 7xxx SOCs internal PHYs"
151 select BCM_NET_PHYLIB
152 help
153 Currently supports the BCM7366, BCM7439, BCM7445, and
154 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
155
156config BCM84881_PHY
157 tristate "Broadcom BCM84881 PHY"
158 help
159 Support the Broadcom BCM84881 PHY.
160
161config BCM87XX_PHY
162 tristate "Broadcom BCM8706 and BCM8727 PHYs"
163 help
164 Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
165
166config BCM_CYGNUS_PHY
167 tristate "Broadcom Cygnus/Omega SoC internal PHY"
168 depends on ARCH_BCM_IPROC || COMPILE_TEST
169 depends on MDIO_BCM_IPROC
170 select BCM_NET_PHYLIB
171 help
172 This PHY driver is for the 1G internal PHYs of the Broadcom
173 Cygnus and Omega Family SoC.
174
175 Currently supports internal PHY's used in the BCM11300,
176 BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
177 BCM58303 & BCM58305 Broadcom Cygnus SoCs.
178
179config BCM_NET_PHYLIB
180 tristate
181
182config BCM_NET_PHYPTP
183 tristate
184
185config CICADA_PHY
186 tristate "Cicada PHYs"
187 help
188 Currently supports the cis8204
189
190config CORTINA_PHY
191 tristate "Cortina EDC CDR 10G Ethernet PHY"
192 help
193 Currently supports the CS4340 phy.
194
195config DAVICOM_PHY
196 tristate "Davicom PHYs"
197 help
198 Currently supports dm9161e and dm9131
199
200config ICPLUS_PHY
201 tristate "ICPlus PHYs"
202 help
203 Currently supports the IP175C and IP1001 PHYs.
204
205config LXT_PHY
206 tristate "Intel LXT PHYs"
207 help
208 Currently supports the lxt970, lxt971
209
210config INTEL_XWAY_PHY
211 tristate "Intel XWAY PHYs"
212 help
213 Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
214 These PHYs are marked as standalone chips under the names
215 PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
216 SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
217
218config LSI_ET1011C_PHY
219 tristate "LSI ET1011C PHY"
220 help
221 Supports the LSI ET1011C PHY.
222
223config MARVELL_PHY
224 tristate "Marvell Alaska PHYs"
225 help
226 Currently has a driver for the 88E1XXX
227
228config MARVELL_10G_PHY
229 tristate "Marvell Alaska 10Gbit PHYs"
230 help
231 Support for the Marvell Alaska MV88X3310 and compatible PHYs.
232
233config MARVELL_88Q2XXX_PHY
234 tristate "Marvell 88Q2XXX PHY"
235 help
236 Support for the Marvell 88Q2XXX 100/1000BASE-T1 Automotive Ethernet
237 PHYs.
238
239config MARVELL_88X2222_PHY
240 tristate "Marvell 88X2222 PHY"
241 help
242 Support for the Marvell 88X2222 Dual-port Multi-speed Ethernet
243 Transceiver.
244
245config MAXLINEAR_GPHY
246 tristate "Maxlinear Ethernet PHYs"
247 select POLYNOMIAL if HWMON
248 depends on HWMON || HWMON=n
249 help
250 Support for the Maxlinear GPY115, GPY211, GPY212, GPY215,
251 GPY241, GPY245 PHYs.
252
253config MEDIATEK_GE_PHY
254 tristate "MediaTek Gigabit Ethernet PHYs"
255 help
256 Supports the MediaTek Gigabit Ethernet PHYs.
257
258config MEDIATEK_GE_SOC_PHY
259 tristate "MediaTek SoC Ethernet PHYs"
260 depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST
261 depends on NVMEM_MTK_EFUSE
262 help
263 Supports MediaTek SoC built-in Gigabit Ethernet PHYs.
264
265 Include support for built-in Ethernet PHYs which are present in
266 the MT7981 and MT7988 SoCs. These PHYs need calibration data
267 present in the SoCs efuse and will dynamically calibrate VCM
268 (common-mode voltage) during startup.
269
270config MICREL_PHY
271 tristate "Micrel PHYs"
272 depends on PTP_1588_CLOCK_OPTIONAL
273 help
274 Supports the KSZ9021, VSC8201, KS8001 PHYs.
275
276config MICROCHIP_T1S_PHY
277 tristate "Microchip 10BASE-T1S Ethernet PHYs"
278 help
279 Currently supports the LAN8670/1/2 Rev.B1 and LAN8650/1 Rev.B0 Internal
280 PHYs.
281
282config MICROCHIP_PHY
283 tristate "Microchip PHYs"
284 help
285 Supports the LAN88XX PHYs.
286
287config MICROCHIP_T1_PHY
288 tristate "Microchip T1 PHYs"
289 help
290 Supports the LAN87XX PHYs.
291
292config MICROSEMI_PHY
293 tristate "Microsemi PHYs"
294 depends on MACSEC || MACSEC=n
295 depends on PTP_1588_CLOCK_OPTIONAL || !NETWORK_PHY_TIMESTAMPING
296 select CRYPTO_LIB_AES if MACSEC
297 help
298 Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
299
300config MOTORCOMM_PHY
301 tristate "Motorcomm PHYs"
302 help
303 Enables support for Motorcomm network PHYs.
304 Currently supports YT85xx Gigabit Ethernet PHYs.
305
306config NATIONAL_PHY
307 tristate "National Semiconductor PHYs"
308 help
309 Currently supports the DP83865 PHY.
310
311config NXP_CBTX_PHY
312 tristate "NXP 100BASE-TX PHYs"
313 help
314 Support the 100BASE-TX PHY integrated on the SJA1110 automotive
315 switch family.
316
317config NXP_C45_TJA11XX_PHY
318 tristate "NXP C45 TJA11XX PHYs"
319 depends on PTP_1588_CLOCK_OPTIONAL
320 depends on MACSEC || !MACSEC
321 help
322 Enable support for NXP C45 TJA11XX PHYs.
323 Currently supports the TJA1103, TJA1104 and TJA1120 PHYs.
324
325config NXP_TJA11XX_PHY
326 tristate "NXP TJA11xx PHYs support"
327 depends on HWMON
328 help
329 Currently supports the NXP TJA1100 and TJA1101 PHY.
330
331config NCN26000_PHY
332 tristate "Onsemi 10BASE-T1S Ethernet PHY"
333 help
334 Adds support for the onsemi 10BASE-T1S Ethernet PHY.
335 Currently supports the NCN26000 10BASE-T1S Industrial PHY
336 with MII interface.
337
338config AT803X_PHY
339 tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
340 depends on REGULATOR
341 help
342 Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
343 QCA8337(Internal qca8k PHY) model
344
345config QSEMI_PHY
346 tristate "Quality Semiconductor PHYs"
347 help
348 Currently supports the qs6612
349
350config REALTEK_PHY
351 tristate "Realtek PHYs"
352 help
353 Supports the Realtek 821x PHY.
354
355config RENESAS_PHY
356 tristate "Renesas PHYs"
357 help
358 Supports the Renesas PHYs uPD60620 and uPD60620A.
359
360config ROCKCHIP_PHY
361 tristate "Rockchip Ethernet PHYs"
362 help
363 Currently supports the integrated Ethernet PHY.
364
365config SMSC_PHY
366 tristate "SMSC PHYs"
367 select CRC16
368 help
369 Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
370
371config STE10XP
372 tristate "STMicroelectronics STe10Xp PHYs"
373 help
374 This is the driver for the STe100p and STe101p PHYs.
375
376config TERANETICS_PHY
377 tristate "Teranetics PHYs"
378 help
379 Currently supports the Teranetics TN2020
380
381config DP83822_PHY
382 tristate "Texas Instruments DP83822/825/826 PHYs"
383 help
384 Supports the DP83822, DP83825I, DP83825CM, DP83825CS, DP83825S,
385 DP83826C and DP83826NC PHYs.
386
387config DP83TC811_PHY
388 tristate "Texas Instruments DP83TC811 PHY"
389 help
390 Supports the DP83TC811 PHY.
391
392config DP83848_PHY
393 tristate "Texas Instruments DP83848 PHY"
394 help
395 Supports the DP83848 PHY.
396
397config DP83867_PHY
398 tristate "Texas Instruments DP83867 Gigabit PHY"
399 help
400 Currently supports the DP83867 PHY.
401
402config DP83869_PHY
403 tristate "Texas Instruments DP83869 Gigabit PHY"
404 help
405 Currently supports the DP83869 PHY. This PHY supports copper and
406 fiber connections.
407
408config DP83TD510_PHY
409 tristate "Texas Instruments DP83TD510 Ethernet 10Base-T1L PHY"
410 help
411 Support for the DP83TD510 Ethernet 10Base-T1L PHY. This PHY supports
412 a 10M single pair Ethernet connection for up to 1000 meter cable.
413
414config DP83TG720_PHY
415 tristate "Texas Instruments DP83TG720 Ethernet 1000Base-T1 PHY"
416 help
417 The DP83TG720S-Q1 is an automotive Ethernet physical layer
418 transceiver compliant with IEEE 802.3bp and Open Alliance
419 standards. It supports key functions necessary for
420 transmitting and receiving data over both unshielded and
421 shielded single twisted-pair cables. This device offers
422 flexible xMII interface options, including support for both
423 RGMII and SGMII MAC interfaces. It's suitable for applications
424 requiring high-speed data transmission in automotive
425 networking environments.
426
427config VITESSE_PHY
428 tristate "Vitesse PHYs"
429 help
430 Currently supports the vsc8244
431
432config XILINX_GMII2RGMII
433 tristate "Xilinx GMII2RGMII converter driver"
434 help
435 This driver support xilinx GMII to RGMII IP core it provides
436 the Reduced Gigabit Media Independent Interface(RGMII) between
437 Ethernet physical media devices and the Gigabit Ethernet controller.
438
439endif # PHYLIB
440
441config MICREL_KS8995MA
442 tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
443 depends on SPI
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# PHY Layer Configuration
4#
5
6menuconfig MDIO_DEVICE
7 tristate "MDIO bus device drivers"
8 help
9 MDIO devices and driver infrastructure code.
10
11if MDIO_DEVICE
12
13config MDIO_BUS
14 tristate
15 default m if PHYLIB=m
16 default MDIO_DEVICE
17 help
18 This internal symbol is used for link time dependencies and it
19 reflects whether the mdio_bus/mdio_device code is built as a
20 loadable module or built-in.
21
22if MDIO_BUS
23
24config MDIO_DEVRES
25 tristate
26
27config MDIO_ASPEED
28 tristate "ASPEED MDIO bus controller"
29 depends on ARCH_ASPEED || COMPILE_TEST
30 depends on OF_MDIO && HAS_IOMEM
31 help
32 This module provides a driver for the independent MDIO bus
33 controllers found in the ASPEED AST2600 SoC. This is a driver for the
34 third revision of the ASPEED MDIO register interface - the first two
35 revisions are the "old" and "new" interfaces found in the AST2400 and
36 AST2500, embedded in the MAC. For legacy reasons, FTGMAC100 driver
37 continues to drive the embedded MDIO controller for the AST2400 and
38 AST2500 SoCs, so say N if AST2600 support is not required.
39
40config MDIO_BCM_IPROC
41 tristate "Broadcom iProc MDIO bus controller"
42 depends on ARCH_BCM_IPROC || COMPILE_TEST
43 depends on HAS_IOMEM && OF_MDIO
44 default ARCH_BCM_IPROC
45 help
46 This module provides a driver for the MDIO busses found in the
47 Broadcom iProc SoC's.
48
49config MDIO_BCM_UNIMAC
50 tristate "Broadcom UniMAC MDIO bus controller"
51 depends on HAS_IOMEM
52 help
53 This module provides a driver for the Broadcom UniMAC MDIO busses.
54 This hardware can be found in the Broadcom GENET Ethernet MAC
55 controllers as well as some Broadcom Ethernet switches such as the
56 Starfighter 2 switches.
57
58config MDIO_BITBANG
59 tristate "Bitbanged MDIO buses"
60 help
61 This module implements the MDIO bus protocol in software,
62 for use by low level drivers that export the ability to
63 drive the relevant pins.
64
65 If in doubt, say N.
66
67config MDIO_BUS_MUX
68 tristate
69 depends on OF_MDIO
70 help
71 This module provides a driver framework for MDIO bus
72 multiplexers which connect one of several child MDIO busses
73 to a parent bus. Switching between child busses is done by
74 device specific drivers.
75
76config MDIO_BUS_MUX_BCM_IPROC
77 tristate "Broadcom iProc based MDIO bus multiplexers"
78 depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
79 select MDIO_BUS_MUX
80 default ARCH_BCM_IPROC
81 help
82 This module provides a driver for MDIO bus multiplexers found in
83 iProc based Broadcom SoCs. This multiplexer connects one of several
84 child MDIO bus to a parent bus. Buses could be internal as well as
85 external and selection logic lies inside the same multiplexer.
86
87config MDIO_BUS_MUX_GPIO
88 tristate "GPIO controlled MDIO bus multiplexers"
89 depends on OF_GPIO && OF_MDIO
90 select MDIO_BUS_MUX
91 help
92 This module provides a driver for MDIO bus multiplexers that
93 are controlled via GPIO lines. The multiplexer connects one of
94 several child MDIO busses to a parent bus. Child bus
95 selection is under the control of GPIO lines.
96
97config MDIO_BUS_MUX_MESON_G12A
98 tristate "Amlogic G12a based MDIO bus multiplexer"
99 depends on ARCH_MESON || COMPILE_TEST
100 depends on OF_MDIO && HAS_IOMEM && COMMON_CLK
101 select MDIO_BUS_MUX
102 default m if ARCH_MESON
103 help
104 This module provides a driver for the MDIO multiplexer/glue of
105 the amlogic g12a SoC. The multiplexers connects either the external
106 or the internal MDIO bus to the parent bus.
107
108config MDIO_BUS_MUX_MMIOREG
109 tristate "MMIO device-controlled MDIO bus multiplexers"
110 depends on OF_MDIO && HAS_IOMEM
111 select MDIO_BUS_MUX
112 help
113 This module provides a driver for MDIO bus multiplexers that
114 are controlled via a simple memory-mapped device, like an FPGA.
115 The multiplexer connects one of several child MDIO busses to a
116 parent bus. Child bus selection is under the control of one of
117 the FPGA's registers.
118
119 Currently, only 8/16/32 bits registers are supported.
120
121config MDIO_BUS_MUX_MULTIPLEXER
122 tristate "MDIO bus multiplexer using kernel multiplexer subsystem"
123 depends on OF_MDIO
124 select MULTIPLEXER
125 select MDIO_BUS_MUX
126 help
127 This module provides a driver for MDIO bus multiplexer
128 that is controlled via the kernel multiplexer subsystem. The
129 bus multiplexer connects one of several child MDIO busses to
130 a parent bus. Child bus selection is under the control of
131 the kernel multiplexer subsystem.
132
133config MDIO_CAVIUM
134 tristate
135
136config MDIO_GPIO
137 tristate "GPIO lib-based bitbanged MDIO buses"
138 depends on MDIO_BITBANG
139 depends on GPIOLIB || COMPILE_TEST
140 help
141 Supports GPIO lib-based MDIO busses.
142
143 To compile this driver as a module, choose M here: the module
144 will be called mdio-gpio.
145
146config MDIO_HISI_FEMAC
147 tristate "Hisilicon FEMAC MDIO bus controller"
148 depends on HAS_IOMEM && OF_MDIO
149 help
150 This module provides a driver for the MDIO busses found in the
151 Hisilicon SoC that have an Fast Ethernet MAC.
152
153config MDIO_I2C
154 tristate
155 depends on I2C
156 help
157 Support I2C based PHYs. This provides a MDIO bus bridged
158 to I2C to allow PHYs connected in I2C mode to be accessed
159 using the existing infrastructure.
160
161 This is library mode.
162
163config MDIO_IPQ4019
164 tristate "Qualcomm IPQ4019 MDIO interface support"
165 depends on HAS_IOMEM && OF_MDIO
166 help
167 This driver supports the MDIO interface found in Qualcomm
168 IPQ40xx series Soc-s.
169
170config MDIO_IPQ8064
171 tristate "Qualcomm IPQ8064 MDIO interface support"
172 depends on HAS_IOMEM && OF_MDIO
173 depends on MFD_SYSCON
174 help
175 This driver supports the MDIO interface found in the network
176 interface units of the IPQ8064 SoC
177
178config MDIO_MOXART
179 tristate "MOXA ART MDIO interface support"
180 depends on ARCH_MOXART || COMPILE_TEST
181 help
182 This driver supports the MDIO interface found in the network
183 interface units of the MOXA ART SoC
184
185config MDIO_MSCC_MIIM
186 tristate "Microsemi MIIM interface support"
187 depends on HAS_IOMEM
188 select MDIO_DEVRES
189 help
190 This driver supports the MIIM (MDIO) interface found in the network
191 switches of the Microsemi SoCs; it is recommended to switch on
192 CONFIG_HIGH_RES_TIMERS
193
194config MDIO_MVUSB
195 tristate "Marvell USB to MDIO Adapter"
196 depends on USB
197 select MDIO_DEVRES
198 help
199 A USB to MDIO converter present on development boards for
200 Marvell's Link Street family of Ethernet switches.
201
202config MDIO_OCTEON
203 tristate "Octeon and some ThunderX SOCs MDIO buses"
204 depends on (64BIT && OF_MDIO) || COMPILE_TEST
205 depends on HAS_IOMEM
206 select MDIO_CAVIUM
207 help
208 This module provides a driver for the Octeon and ThunderX MDIO
209 buses. It is required by the Octeon and ThunderX ethernet device
210 drivers on some systems.
211
212config MDIO_SUN4I
213 tristate "Allwinner sun4i MDIO interface support"
214 depends on ARCH_SUNXI || COMPILE_TEST
215 help
216 This driver supports the MDIO interface found in the network
217 interface units of the Allwinner SoC that have an EMAC (A10,
218 A12, A10s, etc.)
219
220config MDIO_THUNDER
221 tristate "ThunderX SOCs MDIO buses"
222 depends on 64BIT
223 depends on PCI
224 select MDIO_CAVIUM
225 select MDIO_DEVRES
226 help
227 This driver supports the MDIO interfaces found on Cavium
228 ThunderX SoCs when the MDIO bus device appears as a PCI
229 device.
230
231config MDIO_XGENE
232 tristate "APM X-Gene SoC MDIO bus controller"
233 depends on ARCH_XGENE || COMPILE_TEST
234 help
235 This module provides a driver for the MDIO busses found in the
236 APM X-Gene SoC's.
237
238config MDIO_XPCS
239 tristate "Synopsys DesignWare XPCS controller"
240 help
241 This module provides helper functions for Synopsys DesignWare XPCS
242 controllers.
243
244endif
245endif
246
247config PHYLINK
248 tristate
249 depends on NETDEVICES
250 select PHYLIB
251 select SWPHY
252 help
253 PHYlink models the link between the PHY and MAC, allowing fixed
254 configuration links, PHYs, and Serdes links with MAC level
255 autonegotiation modes.
256
257menuconfig PHYLIB
258 tristate "PHY Device support and infrastructure"
259 depends on NETDEVICES
260 select MDIO_DEVICE
261 select MDIO_DEVRES
262 help
263 Ethernet controllers are usually attached to PHY
264 devices. This option provides infrastructure for
265 managing PHY devices.
266
267if PHYLIB
268
269config SWPHY
270 bool
271
272config LED_TRIGGER_PHY
273 bool "Support LED triggers for tracking link state"
274 depends on LEDS_TRIGGERS
275 help
276 Adds support for a set of LED trigger events per-PHY. Link
277 state change will trigger the events, for consumption by an
278 LED class driver. There are triggers for each link speed currently
279 supported by the PHY and also a one common "link" trigger as a
280 logical-or of all the link speed ones.
281 All these triggers are named according to the following pattern:
282 <mii bus id>:<phy>:<speed>
283
284 Where speed is in the form:
285 <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link
286 for any speed known to the PHY.
287
288
289comment "MII PHY device drivers"
290
291config SFP
292 tristate "SFP cage support"
293 depends on I2C && PHYLINK
294 depends on HWMON || HWMON=n
295 select MDIO_I2C
296
297config ADIN_PHY
298 tristate "Analog Devices Industrial Ethernet PHYs"
299 help
300 Adds support for the Analog Devices Industrial Ethernet PHYs.
301 Currently supports the:
302 - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY
303 - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
304 Ethernet PHY
305
306config AMD_PHY
307 tristate "AMD PHYs"
308 help
309 Currently supports the am79c874
310
311config AQUANTIA_PHY
312 tristate "Aquantia PHYs"
313 help
314 Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405
315
316config AX88796B_PHY
317 tristate "Asix PHYs"
318 help
319 Currently supports the Asix Electronics PHY found in the X-Surf 100
320 AX88796B package.
321
322config BCM63XX_PHY
323 tristate "Broadcom 63xx SOCs internal PHY"
324 depends on BCM63XX || COMPILE_TEST
325 select BCM_NET_PHYLIB
326 help
327 Currently supports the 6348 and 6358 PHYs.
328
329config BCM7XXX_PHY
330 tristate "Broadcom 7xxx SOCs internal PHYs"
331 select BCM_NET_PHYLIB
332 help
333 Currently supports the BCM7366, BCM7439, BCM7445, and
334 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
335
336config BCM87XX_PHY
337 tristate "Broadcom BCM8706 and BCM8727 PHYs"
338 help
339 Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
340
341config BCM_CYGNUS_PHY
342 tristate "Broadcom Cygnus/Omega SoC internal PHY"
343 depends on ARCH_BCM_IPROC || COMPILE_TEST
344 depends on MDIO_BCM_IPROC
345 select BCM_NET_PHYLIB
346 help
347 This PHY driver is for the 1G internal PHYs of the Broadcom
348 Cygnus and Omega Family SoC.
349
350 Currently supports internal PHY's used in the BCM11300,
351 BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
352 BCM58303 & BCM58305 Broadcom Cygnus SoCs.
353
354config BCM_NET_PHYLIB
355 tristate
356
357config BROADCOM_PHY
358 tristate "Broadcom PHYs"
359 select BCM_NET_PHYLIB
360 help
361 Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
362 BCM5481, BCM54810 and BCM5482 PHYs.
363
364config BCM54140_PHY
365 tristate "Broadcom BCM54140 PHY"
366 depends on PHYLIB
367 depends on HWMON || HWMON=n
368 select BCM_NET_PHYLIB
369 help
370 Support the Broadcom BCM54140 Quad SGMII/QSGMII PHY.
371
372 This driver also supports the hardware monitoring of this PHY and
373 exposes voltage and temperature sensors.
374
375config BCM84881_PHY
376 tristate "Broadcom BCM84881 PHY"
377 depends on PHYLIB
378 help
379 Support the Broadcom BCM84881 PHY.
380
381config CICADA_PHY
382 tristate "Cicada PHYs"
383 help
384 Currently supports the cis8204
385
386config CORTINA_PHY
387 tristate "Cortina EDC CDR 10G Ethernet PHY"
388 help
389 Currently supports the CS4340 phy.
390
391config DAVICOM_PHY
392 tristate "Davicom PHYs"
393 help
394 Currently supports dm9161e and dm9131
395
396config DP83822_PHY
397 tristate "Texas Instruments DP83822/825/826 PHYs"
398 help
399 Supports the DP83822, DP83825I, DP83825CM, DP83825CS, DP83825S,
400 DP83826C and DP83826NC PHYs.
401
402config DP83TC811_PHY
403 tristate "Texas Instruments DP83TC811 PHY"
404 help
405 Supports the DP83TC811 PHY.
406
407config DP83848_PHY
408 tristate "Texas Instruments DP83848 PHY"
409 help
410 Supports the DP83848 PHY.
411
412config DP83867_PHY
413 tristate "Texas Instruments DP83867 Gigabit PHY"
414 help
415 Currently supports the DP83867 PHY.
416
417config DP83869_PHY
418 tristate "Texas Instruments DP83869 Gigabit PHY"
419 help
420 Currently supports the DP83869 PHY. This PHY supports copper and
421 fiber connections.
422
423config FIXED_PHY
424 tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
425 depends on PHYLIB
426 select SWPHY
427 help
428 Adds the platform "fixed" MDIO Bus to cover the boards that use
429 PHYs that are not connected to the real MDIO bus.
430
431 Currently tested with mpc866ads and mpc8349e-mitx.
432
433config ICPLUS_PHY
434 tristate "ICPlus PHYs"
435 help
436 Currently supports the IP175C and IP1001 PHYs.
437
438config INTEL_XWAY_PHY
439 tristate "Intel XWAY PHYs"
440 help
441 Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
442 These PHYs are marked as standalone chips under the names
443 PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
444 SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
445
446config LSI_ET1011C_PHY
447 tristate "LSI ET1011C PHY"
448 help
449 Supports the LSI ET1011C PHY.
450
451config LXT_PHY
452 tristate "Intel LXT PHYs"
453 help
454 Currently supports the lxt970, lxt971
455
456config MARVELL_PHY
457 tristate "Marvell PHYs"
458 help
459 Currently has a driver for the 88E1011S
460
461config MARVELL_10G_PHY
462 tristate "Marvell Alaska 10Gbit PHYs"
463 help
464 Support for the Marvell Alaska MV88X3310 and compatible PHYs.
465
466config MESON_GXL_PHY
467 tristate "Amlogic Meson GXL Internal PHY"
468 depends on ARCH_MESON || COMPILE_TEST
469 help
470 Currently has a driver for the Amlogic Meson GXL Internal PHY
471
472config MICREL_PHY
473 tristate "Micrel PHYs"
474 help
475 Supports the KSZ9021, VSC8201, KS8001 PHYs.
476
477config MICROCHIP_PHY
478 tristate "Microchip PHYs"
479 help
480 Supports the LAN88XX PHYs.
481
482config MICROCHIP_T1_PHY
483 tristate "Microchip T1 PHYs"
484 help
485 Supports the LAN87XX PHYs.
486
487config MICROSEMI_PHY
488 tristate "Microsemi PHYs"
489 depends on MACSEC || MACSEC=n
490 select CRYPTO_LIB_AES if MACSEC
491 help
492 Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
493
494config NATIONAL_PHY
495 tristate "National Semiconductor PHYs"
496 help
497 Currently supports the DP83865 PHY.
498
499config NXP_TJA11XX_PHY
500 tristate "NXP TJA11xx PHYs support"
501 depends on HWMON
502 help
503 Currently supports the NXP TJA1100 and TJA1101 PHY.
504
505config AT803X_PHY
506 tristate "Qualcomm Atheros AR803X PHYs"
507 depends on REGULATOR
508 help
509 Currently supports the AR8030, AR8031, AR8033 and AR8035 model
510
511config QSEMI_PHY
512 tristate "Quality Semiconductor PHYs"
513 help
514 Currently supports the qs6612
515
516config REALTEK_PHY
517 tristate "Realtek PHYs"
518 help
519 Supports the Realtek 821x PHY.
520
521config RENESAS_PHY
522 tristate "Driver for Renesas PHYs"
523 help
524 Supports the Renesas PHYs uPD60620 and uPD60620A.
525
526config ROCKCHIP_PHY
527 tristate "Driver for Rockchip Ethernet PHYs"
528 help
529 Currently supports the integrated Ethernet PHY.
530
531config SMSC_PHY
532 tristate "SMSC PHYs"
533 help
534 Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
535
536config STE10XP
537 tristate "STMicroelectronics STe10Xp PHYs"
538 help
539 This is the driver for the STe100p and STe101p PHYs.
540
541config TERANETICS_PHY
542 tristate "Teranetics PHYs"
543 help
544 Currently supports the Teranetics TN2020
545
546config VITESSE_PHY
547 tristate "Vitesse PHYs"
548 help
549 Currently supports the vsc8244
550
551config XILINX_GMII2RGMII
552 tristate "Xilinx GMII2RGMII converter driver"
553 help
554 This driver support xilinx GMII to RGMII IP core it provides
555 the Reduced Gigabit Media Independent Interface(RGMII) between
556 Ethernet physical media devices and the Gigabit Ethernet controller.
557
558endif # PHYLIB
559
560config MICREL_KS8995MA
561 tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
562 depends on SPI