Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Driver for the Renesas R-Car I2C unit
4 *
5 * Copyright (C) 2014-19 Wolfram Sang <wsa@sang-engineering.com>
6 * Copyright (C) 2011-2019 Renesas Electronics Corporation
7 *
8 * Copyright (C) 2012-14 Renesas Solutions Corp.
9 * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
10 *
11 * This file is based on the drivers/i2c/busses/i2c-sh7760.c
12 * (c) 2005-2008 MSC Vertriebsges.m.b.H, Manuel Lauss <mlau@msc-ge.com>
13 */
14#include <linux/bitops.h>
15#include <linux/clk.h>
16#include <linux/delay.h>
17#include <linux/dmaengine.h>
18#include <linux/dma-mapping.h>
19#include <linux/err.h>
20#include <linux/interrupt.h>
21#include <linux/io.h>
22#include <linux/iopoll.h>
23#include <linux/i2c.h>
24#include <linux/i2c-smbus.h>
25#include <linux/kernel.h>
26#include <linux/module.h>
27#include <linux/of.h>
28#include <linux/platform_device.h>
29#include <linux/pm_runtime.h>
30#include <linux/reset.h>
31#include <linux/slab.h>
32
33/* register offsets */
34#define ICSCR 0x00 /* slave ctrl */
35#define ICMCR 0x04 /* master ctrl */
36#define ICSSR 0x08 /* slave status */
37#define ICMSR 0x0C /* master status */
38#define ICSIER 0x10 /* slave irq enable */
39#define ICMIER 0x14 /* master irq enable */
40#define ICCCR 0x18 /* clock dividers */
41#define ICSAR 0x1C /* slave address */
42#define ICMAR 0x20 /* master address */
43#define ICRXTX 0x24 /* data port */
44#define ICCCR2 0x28 /* Clock control 2 */
45#define ICMPR 0x2C /* SCL mask control */
46#define ICHPR 0x30 /* SCL HIGH control */
47#define ICLPR 0x34 /* SCL LOW control */
48#define ICFBSCR 0x38 /* first bit setup cycle (Gen3) */
49#define ICDMAER 0x3c /* DMA enable (Gen3) */
50
51/* ICSCR */
52#define SDBS BIT(3) /* slave data buffer select */
53#define SIE BIT(2) /* slave interface enable */
54#define GCAE BIT(1) /* general call address enable */
55#define FNA BIT(0) /* forced non acknowledgment */
56
57/* ICMCR */
58#define MDBS BIT(7) /* non-fifo mode switch */
59#define FSCL BIT(6) /* override SCL pin */
60#define FSDA BIT(5) /* override SDA pin */
61#define OBPC BIT(4) /* override pins */
62#define MIE BIT(3) /* master if enable */
63#define TSBE BIT(2)
64#define FSB BIT(1) /* force stop bit */
65#define ESG BIT(0) /* enable start bit gen */
66
67/* ICSSR (also for ICSIER) */
68#define GCAR BIT(6) /* general call received */
69#define STM BIT(5) /* slave transmit mode */
70#define SSR BIT(4) /* stop received */
71#define SDE BIT(3) /* slave data empty */
72#define SDT BIT(2) /* slave data transmitted */
73#define SDR BIT(1) /* slave data received */
74#define SAR BIT(0) /* slave addr received */
75
76/* ICMSR (also for ICMIE) */
77#define MNR BIT(6) /* nack received */
78#define MAL BIT(5) /* arbitration lost */
79#define MST BIT(4) /* sent a stop */
80#define MDE BIT(3)
81#define MDT BIT(2)
82#define MDR BIT(1)
83#define MAT BIT(0) /* slave addr xfer done */
84
85/* ICDMAER */
86#define RSDMAE BIT(3) /* DMA Slave Received Enable */
87#define TSDMAE BIT(2) /* DMA Slave Transmitted Enable */
88#define RMDMAE BIT(1) /* DMA Master Received Enable */
89#define TMDMAE BIT(0) /* DMA Master Transmitted Enable */
90
91/* ICCCR2 */
92#define FMPE BIT(7) /* Fast Mode Plus Enable */
93#define CDFD BIT(2) /* CDF Disable */
94#define HLSE BIT(1) /* HIGH/LOW Separate Control Enable */
95#define SME BIT(0) /* SCL Mask Enable */
96
97/* ICFBSCR */
98#define TCYC17 0x0f /* 17*Tcyc delay 1st bit between SDA and SCL */
99
100#define RCAR_MIN_DMA_LEN 8
101
102/* SCL low/high ratio 5:4 to meet all I2C timing specs (incl safety margin) */
103#define RCAR_SCLD_RATIO 5
104#define RCAR_SCHD_RATIO 4
105/*
106 * SMD should be smaller than SCLD/SCHD and is always around 20 in the docs.
107 * Thus, we simply use 20 which works for low and high speeds.
108 */
109#define RCAR_DEFAULT_SMD 20
110
111#define RCAR_BUS_PHASE_START (MDBS | MIE | ESG)
112#define RCAR_BUS_PHASE_DATA (MDBS | MIE)
113#define RCAR_BUS_PHASE_STOP (MDBS | MIE | FSB)
114
115#define RCAR_IRQ_SEND (MNR | MAL | MST | MAT | MDE)
116#define RCAR_IRQ_RECV (MNR | MAL | MST | MAT | MDR)
117#define RCAR_IRQ_STOP (MST)
118
119#define ID_LAST_MSG BIT(0)
120#define ID_REP_AFTER_RD BIT(1)
121#define ID_DONE BIT(2)
122#define ID_ARBLOST BIT(3)
123#define ID_NACK BIT(4)
124#define ID_EPROTO BIT(5)
125/* persistent flags */
126#define ID_P_FMPLUS BIT(27)
127#define ID_P_NOT_ATOMIC BIT(28)
128#define ID_P_HOST_NOTIFY BIT(29)
129#define ID_P_NO_RXDMA BIT(30) /* HW forbids RXDMA sometimes */
130#define ID_P_PM_BLOCKED BIT(31)
131#define ID_P_MASK GENMASK(31, 27)
132
133enum rcar_i2c_type {
134 I2C_RCAR_GEN1,
135 I2C_RCAR_GEN2,
136 I2C_RCAR_GEN3,
137 I2C_RCAR_GEN4,
138};
139
140struct rcar_i2c_priv {
141 u32 flags;
142 void __iomem *io;
143 struct i2c_adapter adap;
144 struct i2c_msg *msg;
145 int msgs_left;
146 struct clk *clk;
147
148 wait_queue_head_t wait;
149
150 int pos;
151 u32 icccr;
152 u16 schd;
153 u16 scld;
154 u8 smd;
155 u8 recovery_icmcr; /* protected by adapter lock */
156 enum rcar_i2c_type devtype;
157 struct i2c_client *slave;
158
159 struct resource *res;
160 struct dma_chan *dma_tx;
161 struct dma_chan *dma_rx;
162 struct scatterlist sg;
163 enum dma_data_direction dma_direction;
164
165 struct reset_control *rstc;
166 int irq;
167
168 struct i2c_client *host_notify_client;
169};
170
171#define rcar_i2c_priv_to_dev(p) ((p)->adap.dev.parent)
172#define rcar_i2c_is_recv(p) ((p)->msg->flags & I2C_M_RD)
173
174static void rcar_i2c_write(struct rcar_i2c_priv *priv, int reg, u32 val)
175{
176 writel(val, priv->io + reg);
177}
178
179static u32 rcar_i2c_read(struct rcar_i2c_priv *priv, int reg)
180{
181 return readl(priv->io + reg);
182}
183
184static void rcar_i2c_clear_irq(struct rcar_i2c_priv *priv, u32 val)
185{
186 writel(~val & 0x7f, priv->io + ICMSR);
187}
188
189static int rcar_i2c_get_scl(struct i2c_adapter *adap)
190{
191 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
192
193 return !!(rcar_i2c_read(priv, ICMCR) & FSCL);
194
195};
196
197static void rcar_i2c_set_scl(struct i2c_adapter *adap, int val)
198{
199 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
200
201 if (val)
202 priv->recovery_icmcr |= FSCL;
203 else
204 priv->recovery_icmcr &= ~FSCL;
205
206 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
207};
208
209static void rcar_i2c_set_sda(struct i2c_adapter *adap, int val)
210{
211 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
212
213 if (val)
214 priv->recovery_icmcr |= FSDA;
215 else
216 priv->recovery_icmcr &= ~FSDA;
217
218 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
219};
220
221static int rcar_i2c_get_bus_free(struct i2c_adapter *adap)
222{
223 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
224
225 return !(rcar_i2c_read(priv, ICMCR) & FSDA);
226
227};
228
229static struct i2c_bus_recovery_info rcar_i2c_bri = {
230 .get_scl = rcar_i2c_get_scl,
231 .set_scl = rcar_i2c_set_scl,
232 .set_sda = rcar_i2c_set_sda,
233 .get_bus_free = rcar_i2c_get_bus_free,
234 .recover_bus = i2c_generic_scl_recovery,
235};
236static void rcar_i2c_init(struct rcar_i2c_priv *priv)
237{
238 /* reset master mode */
239 rcar_i2c_write(priv, ICMIER, 0);
240 rcar_i2c_write(priv, ICMCR, MDBS);
241 rcar_i2c_write(priv, ICMSR, 0);
242 /* start clock */
243 if (priv->devtype < I2C_RCAR_GEN3) {
244 rcar_i2c_write(priv, ICCCR, priv->icccr);
245 } else {
246 u32 icccr2 = CDFD | HLSE | SME;
247
248 if (priv->flags & ID_P_FMPLUS)
249 icccr2 |= FMPE;
250
251 rcar_i2c_write(priv, ICCCR2, icccr2);
252 rcar_i2c_write(priv, ICCCR, priv->icccr);
253 rcar_i2c_write(priv, ICMPR, priv->smd);
254 rcar_i2c_write(priv, ICHPR, priv->schd);
255 rcar_i2c_write(priv, ICLPR, priv->scld);
256 rcar_i2c_write(priv, ICFBSCR, TCYC17);
257 }
258}
259
260static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
261{
262 int ret;
263 u32 val;
264
265 ret = readl_poll_timeout(priv->io + ICMCR, val, !(val & FSDA), 10,
266 priv->adap.timeout);
267 if (ret) {
268 /* Waiting did not help, try to recover */
269 priv->recovery_icmcr = MDBS | OBPC | FSDA | FSCL;
270 ret = i2c_recover_bus(&priv->adap);
271 }
272
273 return ret;
274}
275
276static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
277{
278 u32 cdf, round, ick, sum, scl, cdf_width;
279 unsigned long rate;
280 struct device *dev = rcar_i2c_priv_to_dev(priv);
281 struct i2c_timings t = {
282 .bus_freq_hz = I2C_MAX_STANDARD_MODE_FREQ,
283 .scl_fall_ns = 35,
284 .scl_rise_ns = 200,
285 .scl_int_delay_ns = 50,
286 };
287
288 /* Fall back to previously used values if not supplied */
289 i2c_parse_fw_timings(dev, &t, false);
290 priv->smd = RCAR_DEFAULT_SMD;
291
292 /*
293 * calculate SCL clock
294 * see
295 * ICCCR (and ICCCR2 for Gen3+)
296 *
297 * ick = clkp / (1 + CDF)
298 * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick])
299 *
300 * for Gen3+:
301 * SCL = clkp / (8 + SMD * 2 + SCLD + SCHD +F[(ticf + tr + intd) * clkp])
302 *
303 * ick : I2C internal clock < 20 MHz
304 * ticf : I2C SCL falling time
305 * tr : I2C SCL rising time
306 * intd : LSI internal delay
307 * clkp : peripheral_clk
308 * F[] : integer up-valuation
309 */
310 rate = clk_get_rate(priv->clk);
311 cdf = rate / 20000000;
312 cdf_width = (priv->devtype == I2C_RCAR_GEN1) ? 2 : 3;
313 if (cdf >= 1U << cdf_width)
314 goto err_no_val;
315
316 if (t.bus_freq_hz > I2C_MAX_FAST_MODE_FREQ && priv->devtype >= I2C_RCAR_GEN4)
317 priv->flags |= ID_P_FMPLUS;
318 else
319 priv->flags &= ~ID_P_FMPLUS;
320
321 /* On Gen3+, we use cdf only for the filters, not as a SCL divider */
322 ick = rate / (priv->devtype < I2C_RCAR_GEN3 ? (cdf + 1) : 1);
323
324 /*
325 * It is impossible to calculate a large scale number on u32. Separate it.
326 *
327 * F[(ticf + tr + intd) * ick] with sum = (ticf + tr + intd)
328 * = F[sum * ick / 1000000000]
329 * = F[(ick / 1000000) * sum / 1000]
330 */
331 sum = t.scl_fall_ns + t.scl_rise_ns + t.scl_int_delay_ns;
332 round = DIV_ROUND_CLOSEST(ick, 1000000);
333 round = DIV_ROUND_CLOSEST(round * sum, 1000);
334
335 if (priv->devtype < I2C_RCAR_GEN3) {
336 u32 scgd;
337 /*
338 * SCL = ick / (20 + 8 * SCGD + F[(ticf + tr + intd) * ick])
339 * 20 + 8 * SCGD + F[...] = ick / SCL
340 * SCGD = ((ick / SCL) - 20 - F[...]) / 8
341 * Result (= SCL) should be less than bus_speed for hardware safety
342 */
343 scgd = DIV_ROUND_UP(ick, t.bus_freq_hz ?: 1);
344 scgd = DIV_ROUND_UP(scgd - 20 - round, 8);
345 scl = ick / (20 + 8 * scgd + round);
346
347 if (scgd > 0x3f)
348 goto err_no_val;
349
350 dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u, SCGD: %u\n",
351 scl, t.bus_freq_hz, rate, round, cdf, scgd);
352
353 priv->icccr = scgd << cdf_width | cdf;
354 } else {
355 u32 x, sum_ratio = RCAR_SCHD_RATIO + RCAR_SCLD_RATIO;
356 /*
357 * SCLD/SCHD ratio and SMD default value are explained above
358 * where they are defined. With these definitions, we can compute
359 * x as a base value for the SCLD/SCHD ratio:
360 *
361 * SCL = clkp / (8 + 2 * SMD + SCLD + SCHD + F[(ticf + tr + intd) * clkp])
362 * SCL = clkp / (8 + 2 * SMD + RCAR_SCLD_RATIO * x
363 * + RCAR_SCHD_RATIO * x + F[...])
364 *
365 * with: sum_ratio = RCAR_SCLD_RATIO + RCAR_SCHD_RATIO
366 *
367 * SCL = clkp / (8 + 2 * smd + sum_ratio * x + F[...])
368 * 8 + 2 * smd + sum_ratio * x + F[...] = clkp / SCL
369 * x = ((clkp / SCL) - 8 - 2 * smd - F[...]) / sum_ratio
370 */
371 x = DIV_ROUND_UP(rate, t.bus_freq_hz ?: 1);
372 x = DIV_ROUND_UP(x - 8 - 2 * priv->smd - round, sum_ratio);
373 scl = rate / (8 + 2 * priv->smd + sum_ratio * x + round);
374
375 if (x == 0 || x * RCAR_SCLD_RATIO > 0xffff)
376 goto err_no_val;
377
378 priv->icccr = cdf;
379 priv->schd = RCAR_SCHD_RATIO * x;
380 priv->scld = RCAR_SCLD_RATIO * x;
381 if (priv->smd >= priv->schd)
382 priv->smd = priv->schd - 1;
383
384 dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u SCHD %u SCLD %u SMD %u\n",
385 scl, t.bus_freq_hz, rate, round, cdf, priv->schd, priv->scld, priv->smd);
386 }
387
388 return 0;
389
390err_no_val:
391 dev_err(dev, "it is impossible to calculate best SCL\n");
392 return -EINVAL;
393}
394
395/*
396 * We don't have a test case but the HW engineers say that the write order of
397 * ICMSR and ICMCR depends on whether we issue START or REP_START. So, ICMSR
398 * handling is outside of this function. First messages clear ICMSR before this
399 * function, interrupt handlers clear the relevant bits after this function.
400 */
401static void rcar_i2c_prepare_msg(struct rcar_i2c_priv *priv)
402{
403 int read = !!rcar_i2c_is_recv(priv);
404 bool rep_start = !(priv->flags & ID_REP_AFTER_RD);
405
406 priv->pos = 0;
407 priv->flags &= ID_P_MASK;
408
409 if (priv->msgs_left == 1)
410 priv->flags |= ID_LAST_MSG;
411
412 rcar_i2c_write(priv, ICMAR, i2c_8bit_addr_from_msg(priv->msg));
413 if (priv->flags & ID_P_NOT_ATOMIC)
414 rcar_i2c_write(priv, ICMIER, read ? RCAR_IRQ_RECV : RCAR_IRQ_SEND);
415
416 if (rep_start)
417 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
418}
419
420static void rcar_i2c_first_msg(struct rcar_i2c_priv *priv,
421 struct i2c_msg *msgs, int num)
422{
423 priv->msg = msgs;
424 priv->msgs_left = num;
425 rcar_i2c_write(priv, ICMSR, 0); /* must be before preparing msg */
426 rcar_i2c_prepare_msg(priv);
427}
428
429static void rcar_i2c_next_msg(struct rcar_i2c_priv *priv)
430{
431 priv->msg++;
432 priv->msgs_left--;
433 rcar_i2c_prepare_msg(priv);
434 /* ICMSR handling must come afterwards in the irq handler */
435}
436
437static void rcar_i2c_cleanup_dma(struct rcar_i2c_priv *priv, bool terminate)
438{
439 struct dma_chan *chan = priv->dma_direction == DMA_FROM_DEVICE
440 ? priv->dma_rx : priv->dma_tx;
441
442 /* only allowed from thread context! */
443 if (terminate)
444 dmaengine_terminate_sync(chan);
445
446 dma_unmap_single(chan->device->dev, sg_dma_address(&priv->sg),
447 sg_dma_len(&priv->sg), priv->dma_direction);
448
449 /* Gen3+ can only do one RXDMA per transfer and we just completed it */
450 if (priv->devtype >= I2C_RCAR_GEN3 &&
451 priv->dma_direction == DMA_FROM_DEVICE)
452 priv->flags |= ID_P_NO_RXDMA;
453
454 priv->dma_direction = DMA_NONE;
455
456 /* Disable DMA Master Received/Transmitted, must be last! */
457 rcar_i2c_write(priv, ICDMAER, 0);
458}
459
460static void rcar_i2c_dma_callback(void *data)
461{
462 struct rcar_i2c_priv *priv = data;
463
464 priv->pos += sg_dma_len(&priv->sg);
465
466 rcar_i2c_cleanup_dma(priv, false);
467}
468
469static bool rcar_i2c_dma(struct rcar_i2c_priv *priv)
470{
471 struct device *dev = rcar_i2c_priv_to_dev(priv);
472 struct i2c_msg *msg = priv->msg;
473 bool read = msg->flags & I2C_M_RD;
474 enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
475 struct dma_chan *chan = read ? priv->dma_rx : priv->dma_tx;
476 struct dma_async_tx_descriptor *txdesc;
477 dma_addr_t dma_addr;
478 dma_cookie_t cookie;
479 unsigned char *buf;
480 int len;
481
482 /* Do various checks to see if DMA is feasible at all */
483 if (!(priv->flags & ID_P_NOT_ATOMIC) || IS_ERR(chan) || msg->len < RCAR_MIN_DMA_LEN ||
484 !(msg->flags & I2C_M_DMA_SAFE) || (read && priv->flags & ID_P_NO_RXDMA))
485 return false;
486
487 if (read) {
488 /*
489 * The last two bytes needs to be fetched using PIO in
490 * order for the STOP phase to work.
491 */
492 buf = priv->msg->buf;
493 len = priv->msg->len - 2;
494 } else {
495 /*
496 * First byte in message was sent using PIO.
497 */
498 buf = priv->msg->buf + 1;
499 len = priv->msg->len - 1;
500 }
501
502 dma_addr = dma_map_single(chan->device->dev, buf, len, dir);
503 if (dma_mapping_error(chan->device->dev, dma_addr)) {
504 dev_dbg(dev, "dma map failed, using PIO\n");
505 return false;
506 }
507
508 sg_dma_len(&priv->sg) = len;
509 sg_dma_address(&priv->sg) = dma_addr;
510
511 priv->dma_direction = dir;
512
513 txdesc = dmaengine_prep_slave_sg(chan, &priv->sg, 1,
514 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV,
515 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
516 if (!txdesc) {
517 dev_dbg(dev, "dma prep slave sg failed, using PIO\n");
518 rcar_i2c_cleanup_dma(priv, false);
519 return false;
520 }
521
522 txdesc->callback = rcar_i2c_dma_callback;
523 txdesc->callback_param = priv;
524
525 cookie = dmaengine_submit(txdesc);
526 if (dma_submit_error(cookie)) {
527 dev_dbg(dev, "submitting dma failed, using PIO\n");
528 rcar_i2c_cleanup_dma(priv, false);
529 return false;
530 }
531
532 /* Enable DMA Master Received/Transmitted */
533 if (read)
534 rcar_i2c_write(priv, ICDMAER, RMDMAE);
535 else
536 rcar_i2c_write(priv, ICDMAER, TMDMAE);
537
538 dma_async_issue_pending(chan);
539 return true;
540}
541
542static void rcar_i2c_irq_send(struct rcar_i2c_priv *priv, u32 msr)
543{
544 struct i2c_msg *msg = priv->msg;
545 u32 irqs_to_clear = MDE;
546
547 /* FIXME: sometimes, unknown interrupt happened. Do nothing */
548 if (!(msr & MDE))
549 return;
550
551 if (msr & MAT)
552 irqs_to_clear |= MAT;
553
554 /* Check if DMA can be enabled and take over */
555 if (priv->pos == 1 && rcar_i2c_dma(priv))
556 return;
557
558 if (priv->pos < msg->len) {
559 /*
560 * Prepare next data to ICRXTX register.
561 * This data will go to _SHIFT_ register.
562 *
563 * *
564 * [ICRXTX] -> [SHIFT] -> [I2C bus]
565 */
566 rcar_i2c_write(priv, ICRXTX, msg->buf[priv->pos]);
567 priv->pos++;
568 } else {
569 /*
570 * The last data was pushed to ICRXTX on _PREV_ empty irq.
571 * It is on _SHIFT_ register, and will sent to I2C bus.
572 *
573 * *
574 * [ICRXTX] -> [SHIFT] -> [I2C bus]
575 */
576
577 if (priv->flags & ID_LAST_MSG)
578 /*
579 * If current msg is the _LAST_ msg,
580 * prepare stop condition here.
581 * ID_DONE will be set on STOP irq.
582 */
583 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
584 else
585 rcar_i2c_next_msg(priv);
586 }
587
588 rcar_i2c_clear_irq(priv, irqs_to_clear);
589}
590
591static void rcar_i2c_irq_recv(struct rcar_i2c_priv *priv, u32 msr)
592{
593 struct i2c_msg *msg = priv->msg;
594 bool recv_len_init = priv->pos == 0 && msg->flags & I2C_M_RECV_LEN;
595 u32 irqs_to_clear = MDR;
596
597 /* FIXME: sometimes, unknown interrupt happened. Do nothing */
598 if (!(msr & MDR))
599 return;
600
601 if (msr & MAT) {
602 irqs_to_clear |= MAT;
603 /*
604 * Address transfer phase finished, but no data at this point.
605 * Try to use DMA to receive data.
606 */
607 rcar_i2c_dma(priv);
608 } else if (priv->pos < msg->len) {
609 /* get received data */
610 u8 data = rcar_i2c_read(priv, ICRXTX);
611
612 msg->buf[priv->pos] = data;
613 if (recv_len_init) {
614 if (data == 0 || data > I2C_SMBUS_BLOCK_MAX) {
615 priv->flags |= ID_DONE | ID_EPROTO;
616 return;
617 }
618 msg->len += msg->buf[0];
619 /* Enough data for DMA? */
620 if (rcar_i2c_dma(priv))
621 return;
622 /* new length after RECV_LEN now properly initialized */
623 recv_len_init = false;
624 }
625 priv->pos++;
626 }
627
628 /*
629 * If next received data is the _LAST_ and we are not waiting for a new
630 * length because of RECV_LEN, then go to a new phase.
631 */
632 if (priv->pos + 1 == msg->len && !recv_len_init) {
633 if (priv->flags & ID_LAST_MSG) {
634 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
635 } else {
636 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
637 priv->flags |= ID_REP_AFTER_RD;
638 }
639 }
640
641 if (priv->pos == msg->len && !(priv->flags & ID_LAST_MSG))
642 rcar_i2c_next_msg(priv);
643
644 rcar_i2c_clear_irq(priv, irqs_to_clear);
645}
646
647static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
648{
649 u32 ssr_raw, ssr_filtered;
650 u8 value;
651
652 ssr_raw = rcar_i2c_read(priv, ICSSR) & 0xff;
653 ssr_filtered = ssr_raw & rcar_i2c_read(priv, ICSIER);
654
655 if (!ssr_filtered)
656 return false;
657
658 /* address detected */
659 if (ssr_filtered & SAR) {
660 /* read or write request */
661 if (ssr_raw & STM) {
662 i2c_slave_event(priv->slave, I2C_SLAVE_READ_REQUESTED, &value);
663 rcar_i2c_write(priv, ICRXTX, value);
664 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR);
665 } else {
666 i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
667 rcar_i2c_read(priv, ICRXTX); /* dummy read */
668 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR);
669 }
670
671 /* Clear SSR, too, because of old STOPs to other clients than us */
672 rcar_i2c_write(priv, ICSSR, ~(SAR | SSR) & 0xff);
673 }
674
675 /* master sent stop */
676 if (ssr_filtered & SSR) {
677 i2c_slave_event(priv->slave, I2C_SLAVE_STOP, &value);
678 rcar_i2c_write(priv, ICSCR, SIE | SDBS); /* clear our NACK */
679 rcar_i2c_write(priv, ICSIER, SAR);
680 rcar_i2c_write(priv, ICSSR, ~SSR & 0xff);
681 }
682
683 /* master wants to write to us */
684 if (ssr_filtered & SDR) {
685 int ret;
686
687 value = rcar_i2c_read(priv, ICRXTX);
688 ret = i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
689 /* Send NACK in case of error */
690 rcar_i2c_write(priv, ICSCR, SIE | SDBS | (ret < 0 ? FNA : 0));
691 rcar_i2c_write(priv, ICSSR, ~SDR & 0xff);
692 }
693
694 /* master wants to read from us */
695 if (ssr_filtered & SDE) {
696 i2c_slave_event(priv->slave, I2C_SLAVE_READ_PROCESSED, &value);
697 rcar_i2c_write(priv, ICRXTX, value);
698 rcar_i2c_write(priv, ICSSR, ~SDE & 0xff);
699 }
700
701 return true;
702}
703
704/*
705 * This driver has a lock-free design because there are IP cores (at least
706 * R-Car Gen2) which have an inherent race condition in their hardware design.
707 * There, we need to switch to RCAR_BUS_PHASE_DATA as soon as possible after
708 * the interrupt was generated, otherwise an unwanted repeated message gets
709 * generated. It turned out that taking a spinlock at the beginning of the ISR
710 * was already causing repeated messages. Thus, this driver was converted to
711 * the now lockless behaviour. Please keep this in mind when hacking the driver.
712 * R-Car Gen3 seems to have this fixed but earlier versions than R-Car Gen2 are
713 * likely affected. Therefore, we have different interrupt handler entries.
714 */
715static irqreturn_t rcar_i2c_irq(int irq, struct rcar_i2c_priv *priv, u32 msr)
716{
717 if (!msr) {
718 if (rcar_i2c_slave_irq(priv))
719 return IRQ_HANDLED;
720
721 return IRQ_NONE;
722 }
723
724 /* Arbitration lost */
725 if (msr & MAL) {
726 priv->flags |= ID_DONE | ID_ARBLOST;
727 goto out;
728 }
729
730 /* Nack */
731 if (msr & MNR) {
732 /* HW automatically sends STOP after received NACK */
733 if (priv->flags & ID_P_NOT_ATOMIC)
734 rcar_i2c_write(priv, ICMIER, RCAR_IRQ_STOP);
735 priv->flags |= ID_NACK;
736 goto out;
737 }
738
739 /* Stop */
740 if (msr & MST) {
741 priv->msgs_left--; /* The last message also made it */
742 priv->flags |= ID_DONE;
743 goto out;
744 }
745
746 if (rcar_i2c_is_recv(priv))
747 rcar_i2c_irq_recv(priv, msr);
748 else
749 rcar_i2c_irq_send(priv, msr);
750
751out:
752 if (priv->flags & ID_DONE) {
753 rcar_i2c_write(priv, ICMIER, 0);
754 rcar_i2c_write(priv, ICMSR, 0);
755 if (priv->flags & ID_P_NOT_ATOMIC)
756 wake_up(&priv->wait);
757 }
758
759 return IRQ_HANDLED;
760}
761
762static irqreturn_t rcar_i2c_gen2_irq(int irq, void *ptr)
763{
764 struct rcar_i2c_priv *priv = ptr;
765 u32 msr;
766
767 /* Clear START or STOP immediately, except for REPSTART after read */
768 if (likely(!(priv->flags & ID_REP_AFTER_RD)))
769 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA);
770
771 /* Only handle interrupts that are currently enabled */
772 msr = rcar_i2c_read(priv, ICMSR);
773 if (priv->flags & ID_P_NOT_ATOMIC)
774 msr &= rcar_i2c_read(priv, ICMIER);
775
776 return rcar_i2c_irq(irq, priv, msr);
777}
778
779static irqreturn_t rcar_i2c_gen3_irq(int irq, void *ptr)
780{
781 struct rcar_i2c_priv *priv = ptr;
782 u32 msr;
783
784 /* Only handle interrupts that are currently enabled */
785 msr = rcar_i2c_read(priv, ICMSR);
786 if (priv->flags & ID_P_NOT_ATOMIC)
787 msr &= rcar_i2c_read(priv, ICMIER);
788
789 /*
790 * Clear START or STOP immediately, except for REPSTART after read or
791 * if a spurious interrupt was detected.
792 */
793 if (likely(!(priv->flags & ID_REP_AFTER_RD) && msr))
794 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA);
795
796 return rcar_i2c_irq(irq, priv, msr);
797}
798
799static struct dma_chan *rcar_i2c_request_dma_chan(struct device *dev,
800 enum dma_transfer_direction dir,
801 dma_addr_t port_addr)
802{
803 struct dma_chan *chan;
804 struct dma_slave_config cfg;
805 char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx";
806 int ret;
807
808 chan = dma_request_chan(dev, chan_name);
809 if (IS_ERR(chan)) {
810 dev_dbg(dev, "request_channel failed for %s (%ld)\n",
811 chan_name, PTR_ERR(chan));
812 return chan;
813 }
814
815 memset(&cfg, 0, sizeof(cfg));
816 cfg.direction = dir;
817 if (dir == DMA_MEM_TO_DEV) {
818 cfg.dst_addr = port_addr;
819 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
820 } else {
821 cfg.src_addr = port_addr;
822 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
823 }
824
825 ret = dmaengine_slave_config(chan, &cfg);
826 if (ret) {
827 dev_dbg(dev, "slave_config failed for %s (%d)\n",
828 chan_name, ret);
829 dma_release_channel(chan);
830 return ERR_PTR(ret);
831 }
832
833 dev_dbg(dev, "got DMA channel for %s\n", chan_name);
834 return chan;
835}
836
837static void rcar_i2c_request_dma(struct rcar_i2c_priv *priv,
838 struct i2c_msg *msg)
839{
840 struct device *dev = rcar_i2c_priv_to_dev(priv);
841 bool read;
842 struct dma_chan *chan;
843 enum dma_transfer_direction dir;
844
845 read = msg->flags & I2C_M_RD;
846
847 chan = read ? priv->dma_rx : priv->dma_tx;
848 if (PTR_ERR(chan) != -EPROBE_DEFER)
849 return;
850
851 dir = read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV;
852 chan = rcar_i2c_request_dma_chan(dev, dir, priv->res->start + ICRXTX);
853
854 if (read)
855 priv->dma_rx = chan;
856 else
857 priv->dma_tx = chan;
858}
859
860static void rcar_i2c_release_dma(struct rcar_i2c_priv *priv)
861{
862 if (!IS_ERR(priv->dma_tx)) {
863 dma_release_channel(priv->dma_tx);
864 priv->dma_tx = ERR_PTR(-EPROBE_DEFER);
865 }
866
867 if (!IS_ERR(priv->dma_rx)) {
868 dma_release_channel(priv->dma_rx);
869 priv->dma_rx = ERR_PTR(-EPROBE_DEFER);
870 }
871}
872
873/* I2C is a special case, we need to poll the status of a reset */
874static int rcar_i2c_do_reset(struct rcar_i2c_priv *priv)
875{
876 int ret;
877
878 ret = reset_control_reset(priv->rstc);
879 if (ret)
880 return ret;
881
882 return read_poll_timeout_atomic(reset_control_status, ret, ret == 0, 1,
883 100, false, priv->rstc);
884}
885
886static int rcar_i2c_master_xfer(struct i2c_adapter *adap,
887 struct i2c_msg *msgs,
888 int num)
889{
890 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
891 struct device *dev = rcar_i2c_priv_to_dev(priv);
892 int i, ret;
893 long time_left;
894
895 priv->flags |= ID_P_NOT_ATOMIC;
896
897 pm_runtime_get_sync(dev);
898
899 /* Check bus state before init otherwise bus busy info will be lost */
900 ret = rcar_i2c_bus_barrier(priv);
901 if (ret < 0)
902 goto out;
903
904 /* Gen3+ needs a reset. That also allows RXDMA once */
905 if (priv->devtype >= I2C_RCAR_GEN3) {
906 priv->flags &= ~ID_P_NO_RXDMA;
907 ret = rcar_i2c_do_reset(priv);
908 if (ret)
909 goto out;
910 }
911
912 rcar_i2c_init(priv);
913
914 for (i = 0; i < num; i++)
915 rcar_i2c_request_dma(priv, msgs + i);
916
917 rcar_i2c_first_msg(priv, msgs, num);
918
919 time_left = wait_event_timeout(priv->wait, priv->flags & ID_DONE,
920 num * adap->timeout);
921
922 /* cleanup DMA if it couldn't complete properly due to an error */
923 if (priv->dma_direction != DMA_NONE)
924 rcar_i2c_cleanup_dma(priv, true);
925
926 if (!time_left) {
927 rcar_i2c_init(priv);
928 ret = -ETIMEDOUT;
929 } else if (priv->flags & ID_NACK) {
930 ret = -ENXIO;
931 } else if (priv->flags & ID_ARBLOST) {
932 ret = -EAGAIN;
933 } else if (priv->flags & ID_EPROTO) {
934 ret = -EPROTO;
935 } else {
936 ret = num - priv->msgs_left; /* The number of transfer */
937 }
938out:
939 pm_runtime_put(dev);
940
941 if (ret < 0 && ret != -ENXIO)
942 dev_err(dev, "error %d : %x\n", ret, priv->flags);
943
944 return ret;
945}
946
947static int rcar_i2c_master_xfer_atomic(struct i2c_adapter *adap,
948 struct i2c_msg *msgs,
949 int num)
950{
951 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
952 struct device *dev = rcar_i2c_priv_to_dev(priv);
953 unsigned long j;
954 bool time_left;
955 int ret;
956
957 priv->flags &= ~ID_P_NOT_ATOMIC;
958
959 pm_runtime_get_sync(dev);
960
961 /* Check bus state before init otherwise bus busy info will be lost */
962 ret = rcar_i2c_bus_barrier(priv);
963 if (ret < 0)
964 goto out;
965
966 rcar_i2c_init(priv);
967 rcar_i2c_first_msg(priv, msgs, num);
968
969 j = jiffies + num * adap->timeout;
970 do {
971 u32 msr = rcar_i2c_read(priv, ICMSR);
972
973 msr &= (rcar_i2c_is_recv(priv) ? RCAR_IRQ_RECV : RCAR_IRQ_SEND) | RCAR_IRQ_STOP;
974
975 if (msr) {
976 if (priv->devtype < I2C_RCAR_GEN3)
977 rcar_i2c_gen2_irq(0, priv);
978 else
979 rcar_i2c_gen3_irq(0, priv);
980 }
981
982 time_left = time_before_eq(jiffies, j);
983 } while (!(priv->flags & ID_DONE) && time_left);
984
985 if (!time_left) {
986 rcar_i2c_init(priv);
987 ret = -ETIMEDOUT;
988 } else if (priv->flags & ID_NACK) {
989 ret = -ENXIO;
990 } else if (priv->flags & ID_ARBLOST) {
991 ret = -EAGAIN;
992 } else if (priv->flags & ID_EPROTO) {
993 ret = -EPROTO;
994 } else {
995 ret = num - priv->msgs_left; /* The number of transfer */
996 }
997out:
998 pm_runtime_put(dev);
999
1000 if (ret < 0 && ret != -ENXIO)
1001 dev_err(dev, "error %d : %x\n", ret, priv->flags);
1002
1003 return ret;
1004}
1005
1006static int rcar_reg_slave(struct i2c_client *slave)
1007{
1008 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter);
1009
1010 if (priv->slave)
1011 return -EBUSY;
1012
1013 if (slave->flags & I2C_CLIENT_TEN)
1014 return -EAFNOSUPPORT;
1015
1016 /* Keep device active for slave address detection logic */
1017 pm_runtime_get_sync(rcar_i2c_priv_to_dev(priv));
1018
1019 priv->slave = slave;
1020 rcar_i2c_write(priv, ICSAR, slave->addr);
1021 rcar_i2c_write(priv, ICSSR, 0);
1022 rcar_i2c_write(priv, ICSIER, SAR);
1023 rcar_i2c_write(priv, ICSCR, SIE | SDBS);
1024
1025 return 0;
1026}
1027
1028static int rcar_unreg_slave(struct i2c_client *slave)
1029{
1030 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter);
1031
1032 WARN_ON(!priv->slave);
1033
1034 /* ensure no irq is running before clearing ptr */
1035 disable_irq(priv->irq);
1036 rcar_i2c_write(priv, ICSIER, 0);
1037 rcar_i2c_write(priv, ICSSR, 0);
1038 enable_irq(priv->irq);
1039 rcar_i2c_write(priv, ICSCR, SDBS);
1040 rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
1041
1042 priv->slave = NULL;
1043
1044 pm_runtime_put(rcar_i2c_priv_to_dev(priv));
1045
1046 return 0;
1047}
1048
1049static u32 rcar_i2c_func(struct i2c_adapter *adap)
1050{
1051 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
1052
1053 /*
1054 * This HW can't do:
1055 * I2C_SMBUS_QUICK (setting FSB during START didn't work)
1056 * I2C_M_NOSTART (automatically sends address after START)
1057 * I2C_M_IGNORE_NAK (automatically sends STOP after NAK)
1058 */
1059 u32 func = I2C_FUNC_I2C | I2C_FUNC_SLAVE |
1060 (I2C_FUNC_SMBUS_EMUL_ALL & ~I2C_FUNC_SMBUS_QUICK);
1061
1062 if (priv->flags & ID_P_HOST_NOTIFY)
1063 func |= I2C_FUNC_SMBUS_HOST_NOTIFY;
1064
1065 return func;
1066}
1067
1068static const struct i2c_algorithm rcar_i2c_algo = {
1069 .master_xfer = rcar_i2c_master_xfer,
1070 .master_xfer_atomic = rcar_i2c_master_xfer_atomic,
1071 .functionality = rcar_i2c_func,
1072 .reg_slave = rcar_reg_slave,
1073 .unreg_slave = rcar_unreg_slave,
1074};
1075
1076static const struct i2c_adapter_quirks rcar_i2c_quirks = {
1077 .flags = I2C_AQ_NO_ZERO_LEN,
1078};
1079
1080static const struct of_device_id rcar_i2c_dt_ids[] = {
1081 { .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 },
1082 { .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 },
1083 { .compatible = "renesas,i2c-r8a7790", .data = (void *)I2C_RCAR_GEN2 },
1084 { .compatible = "renesas,i2c-r8a7791", .data = (void *)I2C_RCAR_GEN2 },
1085 { .compatible = "renesas,i2c-r8a7792", .data = (void *)I2C_RCAR_GEN2 },
1086 { .compatible = "renesas,i2c-r8a7793", .data = (void *)I2C_RCAR_GEN2 },
1087 { .compatible = "renesas,i2c-r8a7794", .data = (void *)I2C_RCAR_GEN2 },
1088 { .compatible = "renesas,i2c-r8a7795", .data = (void *)I2C_RCAR_GEN3 },
1089 { .compatible = "renesas,i2c-r8a7796", .data = (void *)I2C_RCAR_GEN3 },
1090 /* S4 has no FM+ bit */
1091 { .compatible = "renesas,i2c-r8a779f0", .data = (void *)I2C_RCAR_GEN3 },
1092 { .compatible = "renesas,rcar-gen1-i2c", .data = (void *)I2C_RCAR_GEN1 },
1093 { .compatible = "renesas,rcar-gen2-i2c", .data = (void *)I2C_RCAR_GEN2 },
1094 { .compatible = "renesas,rcar-gen3-i2c", .data = (void *)I2C_RCAR_GEN3 },
1095 { .compatible = "renesas,rcar-gen4-i2c", .data = (void *)I2C_RCAR_GEN4 },
1096 {},
1097};
1098MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids);
1099
1100static int rcar_i2c_probe(struct platform_device *pdev)
1101{
1102 struct rcar_i2c_priv *priv;
1103 struct i2c_adapter *adap;
1104 struct device *dev = &pdev->dev;
1105 unsigned long irqflags = 0;
1106 irqreturn_t (*irqhandler)(int irq, void *ptr) = rcar_i2c_gen3_irq;
1107 int ret;
1108
1109 /* Otherwise logic will break because some bytes must always use PIO */
1110 BUILD_BUG_ON_MSG(RCAR_MIN_DMA_LEN < 3, "Invalid min DMA length");
1111
1112 priv = devm_kzalloc(dev, sizeof(struct rcar_i2c_priv), GFP_KERNEL);
1113 if (!priv)
1114 return -ENOMEM;
1115
1116 priv->clk = devm_clk_get(dev, NULL);
1117 if (IS_ERR(priv->clk)) {
1118 dev_err(dev, "cannot get clock\n");
1119 return PTR_ERR(priv->clk);
1120 }
1121
1122 priv->io = devm_platform_get_and_ioremap_resource(pdev, 0, &priv->res);
1123 if (IS_ERR(priv->io))
1124 return PTR_ERR(priv->io);
1125
1126 priv->devtype = (enum rcar_i2c_type)of_device_get_match_data(dev);
1127 init_waitqueue_head(&priv->wait);
1128
1129 adap = &priv->adap;
1130 adap->nr = pdev->id;
1131 adap->algo = &rcar_i2c_algo;
1132 adap->class = I2C_CLASS_DEPRECATED;
1133 adap->retries = 3;
1134 adap->dev.parent = dev;
1135 adap->dev.of_node = dev->of_node;
1136 adap->bus_recovery_info = &rcar_i2c_bri;
1137 adap->quirks = &rcar_i2c_quirks;
1138 i2c_set_adapdata(adap, priv);
1139 strscpy(adap->name, pdev->name, sizeof(adap->name));
1140
1141 /* Init DMA */
1142 sg_init_table(&priv->sg, 1);
1143 priv->dma_direction = DMA_NONE;
1144 priv->dma_rx = priv->dma_tx = ERR_PTR(-EPROBE_DEFER);
1145
1146 /* Activate device for clock calculation */
1147 pm_runtime_enable(dev);
1148 pm_runtime_get_sync(dev);
1149 ret = rcar_i2c_clock_calculate(priv);
1150 if (ret < 0) {
1151 pm_runtime_put(dev);
1152 goto out_pm_disable;
1153 }
1154
1155 rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
1156
1157 if (priv->devtype < I2C_RCAR_GEN3) {
1158 irqflags |= IRQF_NO_THREAD;
1159 irqhandler = rcar_i2c_gen2_irq;
1160 }
1161
1162 /* Stay always active when multi-master to keep arbitration working */
1163 if (of_property_read_bool(dev->of_node, "multi-master"))
1164 priv->flags |= ID_P_PM_BLOCKED;
1165 else
1166 pm_runtime_put(dev);
1167
1168 if (of_property_read_bool(dev->of_node, "smbus"))
1169 priv->flags |= ID_P_HOST_NOTIFY;
1170
1171 if (priv->devtype >= I2C_RCAR_GEN3) {
1172 priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
1173 if (IS_ERR(priv->rstc)) {
1174 ret = PTR_ERR(priv->rstc);
1175 goto out_pm_put;
1176 }
1177
1178 ret = reset_control_status(priv->rstc);
1179 if (ret < 0)
1180 goto out_pm_put;
1181 }
1182
1183 ret = platform_get_irq(pdev, 0);
1184 if (ret < 0)
1185 goto out_pm_put;
1186 priv->irq = ret;
1187 ret = devm_request_irq(dev, priv->irq, irqhandler, irqflags, dev_name(dev), priv);
1188 if (ret < 0) {
1189 dev_err(dev, "cannot get irq %d\n", priv->irq);
1190 goto out_pm_put;
1191 }
1192
1193 platform_set_drvdata(pdev, priv);
1194
1195 ret = i2c_add_numbered_adapter(adap);
1196 if (ret < 0)
1197 goto out_pm_put;
1198
1199 if (priv->flags & ID_P_HOST_NOTIFY) {
1200 priv->host_notify_client = i2c_new_slave_host_notify_device(adap);
1201 if (IS_ERR(priv->host_notify_client)) {
1202 ret = PTR_ERR(priv->host_notify_client);
1203 goto out_del_device;
1204 }
1205 }
1206
1207 dev_info(dev, "probed\n");
1208
1209 return 0;
1210
1211 out_del_device:
1212 i2c_del_adapter(&priv->adap);
1213 out_pm_put:
1214 if (priv->flags & ID_P_PM_BLOCKED)
1215 pm_runtime_put(dev);
1216 out_pm_disable:
1217 pm_runtime_disable(dev);
1218 return ret;
1219}
1220
1221static void rcar_i2c_remove(struct platform_device *pdev)
1222{
1223 struct rcar_i2c_priv *priv = platform_get_drvdata(pdev);
1224 struct device *dev = &pdev->dev;
1225
1226 if (priv->host_notify_client)
1227 i2c_free_slave_host_notify_device(priv->host_notify_client);
1228 i2c_del_adapter(&priv->adap);
1229 rcar_i2c_release_dma(priv);
1230 if (priv->flags & ID_P_PM_BLOCKED)
1231 pm_runtime_put(dev);
1232 pm_runtime_disable(dev);
1233}
1234
1235static int rcar_i2c_suspend(struct device *dev)
1236{
1237 struct rcar_i2c_priv *priv = dev_get_drvdata(dev);
1238
1239 i2c_mark_adapter_suspended(&priv->adap);
1240 return 0;
1241}
1242
1243static int rcar_i2c_resume(struct device *dev)
1244{
1245 struct rcar_i2c_priv *priv = dev_get_drvdata(dev);
1246
1247 i2c_mark_adapter_resumed(&priv->adap);
1248 return 0;
1249}
1250
1251static const struct dev_pm_ops rcar_i2c_pm_ops = {
1252 NOIRQ_SYSTEM_SLEEP_PM_OPS(rcar_i2c_suspend, rcar_i2c_resume)
1253};
1254
1255static struct platform_driver rcar_i2c_driver = {
1256 .driver = {
1257 .name = "i2c-rcar",
1258 .of_match_table = rcar_i2c_dt_ids,
1259 .pm = pm_sleep_ptr(&rcar_i2c_pm_ops),
1260 },
1261 .probe = rcar_i2c_probe,
1262 .remove_new = rcar_i2c_remove,
1263};
1264
1265module_platform_driver(rcar_i2c_driver);
1266
1267MODULE_LICENSE("GPL v2");
1268MODULE_DESCRIPTION("Renesas R-Car I2C bus driver");
1269MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Driver for the Renesas R-Car I2C unit
4 *
5 * Copyright (C) 2014-19 Wolfram Sang <wsa@sang-engineering.com>
6 * Copyright (C) 2011-2019 Renesas Electronics Corporation
7 *
8 * Copyright (C) 2012-14 Renesas Solutions Corp.
9 * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
10 *
11 * This file is based on the drivers/i2c/busses/i2c-sh7760.c
12 * (c) 2005-2008 MSC Vertriebsges.m.b.H, Manuel Lauss <mlau@msc-ge.com>
13 */
14#include <linux/bitops.h>
15#include <linux/clk.h>
16#include <linux/delay.h>
17#include <linux/dmaengine.h>
18#include <linux/dma-mapping.h>
19#include <linux/err.h>
20#include <linux/interrupt.h>
21#include <linux/io.h>
22#include <linux/i2c.h>
23#include <linux/kernel.h>
24#include <linux/module.h>
25#include <linux/of_device.h>
26#include <linux/platform_device.h>
27#include <linux/pm_runtime.h>
28#include <linux/reset.h>
29#include <linux/slab.h>
30
31/* register offsets */
32#define ICSCR 0x00 /* slave ctrl */
33#define ICMCR 0x04 /* master ctrl */
34#define ICSSR 0x08 /* slave status */
35#define ICMSR 0x0C /* master status */
36#define ICSIER 0x10 /* slave irq enable */
37#define ICMIER 0x14 /* master irq enable */
38#define ICCCR 0x18 /* clock dividers */
39#define ICSAR 0x1C /* slave address */
40#define ICMAR 0x20 /* master address */
41#define ICRXTX 0x24 /* data port */
42#define ICFBSCR 0x38 /* first bit setup cycle (Gen3) */
43#define ICDMAER 0x3c /* DMA enable (Gen3) */
44
45/* ICSCR */
46#define SDBS (1 << 3) /* slave data buffer select */
47#define SIE (1 << 2) /* slave interface enable */
48#define GCAE (1 << 1) /* general call address enable */
49#define FNA (1 << 0) /* forced non acknowledgment */
50
51/* ICMCR */
52#define MDBS (1 << 7) /* non-fifo mode switch */
53#define FSCL (1 << 6) /* override SCL pin */
54#define FSDA (1 << 5) /* override SDA pin */
55#define OBPC (1 << 4) /* override pins */
56#define MIE (1 << 3) /* master if enable */
57#define TSBE (1 << 2)
58#define FSB (1 << 1) /* force stop bit */
59#define ESG (1 << 0) /* enable start bit gen */
60
61/* ICSSR (also for ICSIER) */
62#define GCAR (1 << 6) /* general call received */
63#define STM (1 << 5) /* slave transmit mode */
64#define SSR (1 << 4) /* stop received */
65#define SDE (1 << 3) /* slave data empty */
66#define SDT (1 << 2) /* slave data transmitted */
67#define SDR (1 << 1) /* slave data received */
68#define SAR (1 << 0) /* slave addr received */
69
70/* ICMSR (also for ICMIE) */
71#define MNR (1 << 6) /* nack received */
72#define MAL (1 << 5) /* arbitration lost */
73#define MST (1 << 4) /* sent a stop */
74#define MDE (1 << 3)
75#define MDT (1 << 2)
76#define MDR (1 << 1)
77#define MAT (1 << 0) /* slave addr xfer done */
78
79/* ICDMAER */
80#define RSDMAE (1 << 3) /* DMA Slave Received Enable */
81#define TSDMAE (1 << 2) /* DMA Slave Transmitted Enable */
82#define RMDMAE (1 << 1) /* DMA Master Received Enable */
83#define TMDMAE (1 << 0) /* DMA Master Transmitted Enable */
84
85/* ICFBSCR */
86#define TCYC17 0x0f /* 17*Tcyc delay 1st bit between SDA and SCL */
87
88#define RCAR_MIN_DMA_LEN 8
89
90#define RCAR_BUS_PHASE_START (MDBS | MIE | ESG)
91#define RCAR_BUS_PHASE_DATA (MDBS | MIE)
92#define RCAR_BUS_MASK_DATA (~(ESG | FSB) & 0xFF)
93#define RCAR_BUS_PHASE_STOP (MDBS | MIE | FSB)
94
95#define RCAR_IRQ_SEND (MNR | MAL | MST | MAT | MDE)
96#define RCAR_IRQ_RECV (MNR | MAL | MST | MAT | MDR)
97#define RCAR_IRQ_STOP (MST)
98
99#define RCAR_IRQ_ACK_SEND (~(MAT | MDE) & 0x7F)
100#define RCAR_IRQ_ACK_RECV (~(MAT | MDR) & 0x7F)
101
102#define ID_LAST_MSG (1 << 0)
103#define ID_FIRST_MSG (1 << 1)
104#define ID_DONE (1 << 2)
105#define ID_ARBLOST (1 << 3)
106#define ID_NACK (1 << 4)
107/* persistent flags */
108#define ID_P_REP_AFTER_RD BIT(29)
109#define ID_P_NO_RXDMA BIT(30) /* HW forbids RXDMA sometimes */
110#define ID_P_PM_BLOCKED BIT(31)
111#define ID_P_MASK GENMASK(31, 29)
112
113enum rcar_i2c_type {
114 I2C_RCAR_GEN1,
115 I2C_RCAR_GEN2,
116 I2C_RCAR_GEN3,
117};
118
119struct rcar_i2c_priv {
120 void __iomem *io;
121 struct i2c_adapter adap;
122 struct i2c_msg *msg;
123 int msgs_left;
124 struct clk *clk;
125
126 wait_queue_head_t wait;
127
128 int pos;
129 u32 icccr;
130 u32 flags;
131 u8 recovery_icmcr; /* protected by adapter lock */
132 enum rcar_i2c_type devtype;
133 struct i2c_client *slave;
134
135 struct resource *res;
136 struct dma_chan *dma_tx;
137 struct dma_chan *dma_rx;
138 struct scatterlist sg;
139 enum dma_data_direction dma_direction;
140
141 struct reset_control *rstc;
142 int irq;
143};
144
145#define rcar_i2c_priv_to_dev(p) ((p)->adap.dev.parent)
146#define rcar_i2c_is_recv(p) ((p)->msg->flags & I2C_M_RD)
147
148#define LOOP_TIMEOUT 1024
149
150
151static void rcar_i2c_write(struct rcar_i2c_priv *priv, int reg, u32 val)
152{
153 writel(val, priv->io + reg);
154}
155
156static u32 rcar_i2c_read(struct rcar_i2c_priv *priv, int reg)
157{
158 return readl(priv->io + reg);
159}
160
161static int rcar_i2c_get_scl(struct i2c_adapter *adap)
162{
163 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
164
165 return !!(rcar_i2c_read(priv, ICMCR) & FSCL);
166
167};
168
169static void rcar_i2c_set_scl(struct i2c_adapter *adap, int val)
170{
171 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
172
173 if (val)
174 priv->recovery_icmcr |= FSCL;
175 else
176 priv->recovery_icmcr &= ~FSCL;
177
178 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
179};
180
181static void rcar_i2c_set_sda(struct i2c_adapter *adap, int val)
182{
183 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
184
185 if (val)
186 priv->recovery_icmcr |= FSDA;
187 else
188 priv->recovery_icmcr &= ~FSDA;
189
190 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
191};
192
193static int rcar_i2c_get_bus_free(struct i2c_adapter *adap)
194{
195 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
196
197 return !(rcar_i2c_read(priv, ICMCR) & FSDA);
198
199};
200
201static struct i2c_bus_recovery_info rcar_i2c_bri = {
202 .get_scl = rcar_i2c_get_scl,
203 .set_scl = rcar_i2c_set_scl,
204 .set_sda = rcar_i2c_set_sda,
205 .get_bus_free = rcar_i2c_get_bus_free,
206 .recover_bus = i2c_generic_scl_recovery,
207};
208static void rcar_i2c_init(struct rcar_i2c_priv *priv)
209{
210 /* reset master mode */
211 rcar_i2c_write(priv, ICMIER, 0);
212 rcar_i2c_write(priv, ICMCR, MDBS);
213 rcar_i2c_write(priv, ICMSR, 0);
214 /* start clock */
215 rcar_i2c_write(priv, ICCCR, priv->icccr);
216
217 if (priv->devtype == I2C_RCAR_GEN3)
218 rcar_i2c_write(priv, ICFBSCR, TCYC17);
219
220}
221
222static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
223{
224 int i;
225
226 for (i = 0; i < LOOP_TIMEOUT; i++) {
227 /* make sure that bus is not busy */
228 if (!(rcar_i2c_read(priv, ICMCR) & FSDA))
229 return 0;
230 udelay(1);
231 }
232
233 /* Waiting did not help, try to recover */
234 priv->recovery_icmcr = MDBS | OBPC | FSDA | FSCL;
235 return i2c_recover_bus(&priv->adap);
236}
237
238static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
239{
240 u32 scgd, cdf, round, ick, sum, scl, cdf_width;
241 unsigned long rate;
242 struct device *dev = rcar_i2c_priv_to_dev(priv);
243 struct i2c_timings t = {
244 .bus_freq_hz = I2C_MAX_STANDARD_MODE_FREQ,
245 .scl_fall_ns = 35,
246 .scl_rise_ns = 200,
247 .scl_int_delay_ns = 50,
248 };
249
250 /* Fall back to previously used values if not supplied */
251 i2c_parse_fw_timings(dev, &t, false);
252
253 switch (priv->devtype) {
254 case I2C_RCAR_GEN1:
255 cdf_width = 2;
256 break;
257 case I2C_RCAR_GEN2:
258 case I2C_RCAR_GEN3:
259 cdf_width = 3;
260 break;
261 default:
262 dev_err(dev, "device type error\n");
263 return -EIO;
264 }
265
266 /*
267 * calculate SCL clock
268 * see
269 * ICCCR
270 *
271 * ick = clkp / (1 + CDF)
272 * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick])
273 *
274 * ick : I2C internal clock < 20 MHz
275 * ticf : I2C SCL falling time
276 * tr : I2C SCL rising time
277 * intd : LSI internal delay
278 * clkp : peripheral_clk
279 * F[] : integer up-valuation
280 */
281 rate = clk_get_rate(priv->clk);
282 cdf = rate / 20000000;
283 if (cdf >= 1U << cdf_width) {
284 dev_err(dev, "Input clock %lu too high\n", rate);
285 return -EIO;
286 }
287 ick = rate / (cdf + 1);
288
289 /*
290 * it is impossible to calculate large scale
291 * number on u32. separate it
292 *
293 * F[(ticf + tr + intd) * ick] with sum = (ticf + tr + intd)
294 * = F[sum * ick / 1000000000]
295 * = F[(ick / 1000000) * sum / 1000]
296 */
297 sum = t.scl_fall_ns + t.scl_rise_ns + t.scl_int_delay_ns;
298 round = (ick + 500000) / 1000000 * sum;
299 round = (round + 500) / 1000;
300
301 /*
302 * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick])
303 *
304 * Calculation result (= SCL) should be less than
305 * bus_speed for hardware safety
306 *
307 * We could use something along the lines of
308 * div = ick / (bus_speed + 1) + 1;
309 * scgd = (div - 20 - round + 7) / 8;
310 * scl = ick / (20 + (scgd * 8) + round);
311 * (not fully verified) but that would get pretty involved
312 */
313 for (scgd = 0; scgd < 0x40; scgd++) {
314 scl = ick / (20 + (scgd * 8) + round);
315 if (scl <= t.bus_freq_hz)
316 goto scgd_find;
317 }
318 dev_err(dev, "it is impossible to calculate best SCL\n");
319 return -EIO;
320
321scgd_find:
322 dev_dbg(dev, "clk %d/%d(%lu), round %u, CDF:0x%x, SCGD: 0x%x\n",
323 scl, t.bus_freq_hz, rate, round, cdf, scgd);
324
325 /* keep icccr value */
326 priv->icccr = scgd << cdf_width | cdf;
327
328 return 0;
329}
330
331static void rcar_i2c_prepare_msg(struct rcar_i2c_priv *priv)
332{
333 int read = !!rcar_i2c_is_recv(priv);
334
335 priv->pos = 0;
336 if (priv->msgs_left == 1)
337 priv->flags |= ID_LAST_MSG;
338
339 rcar_i2c_write(priv, ICMAR, i2c_8bit_addr_from_msg(priv->msg));
340 /*
341 * We don't have a test case but the HW engineers say that the write order
342 * of ICMSR and ICMCR depends on whether we issue START or REP_START. Since
343 * it didn't cause a drawback for me, let's rather be safe than sorry.
344 */
345 if (priv->flags & ID_FIRST_MSG) {
346 rcar_i2c_write(priv, ICMSR, 0);
347 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
348 } else {
349 if (priv->flags & ID_P_REP_AFTER_RD)
350 priv->flags &= ~ID_P_REP_AFTER_RD;
351 else
352 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
353 rcar_i2c_write(priv, ICMSR, 0);
354 }
355 rcar_i2c_write(priv, ICMIER, read ? RCAR_IRQ_RECV : RCAR_IRQ_SEND);
356}
357
358static void rcar_i2c_next_msg(struct rcar_i2c_priv *priv)
359{
360 priv->msg++;
361 priv->msgs_left--;
362 priv->flags &= ID_P_MASK;
363 rcar_i2c_prepare_msg(priv);
364}
365
366static void rcar_i2c_dma_unmap(struct rcar_i2c_priv *priv)
367{
368 struct dma_chan *chan = priv->dma_direction == DMA_FROM_DEVICE
369 ? priv->dma_rx : priv->dma_tx;
370
371 dma_unmap_single(chan->device->dev, sg_dma_address(&priv->sg),
372 sg_dma_len(&priv->sg), priv->dma_direction);
373
374 /* Gen3 can only do one RXDMA per transfer and we just completed it */
375 if (priv->devtype == I2C_RCAR_GEN3 &&
376 priv->dma_direction == DMA_FROM_DEVICE)
377 priv->flags |= ID_P_NO_RXDMA;
378
379 priv->dma_direction = DMA_NONE;
380
381 /* Disable DMA Master Received/Transmitted, must be last! */
382 rcar_i2c_write(priv, ICDMAER, 0);
383}
384
385static void rcar_i2c_cleanup_dma(struct rcar_i2c_priv *priv)
386{
387 if (priv->dma_direction == DMA_NONE)
388 return;
389 else if (priv->dma_direction == DMA_FROM_DEVICE)
390 dmaengine_terminate_all(priv->dma_rx);
391 else if (priv->dma_direction == DMA_TO_DEVICE)
392 dmaengine_terminate_all(priv->dma_tx);
393
394 rcar_i2c_dma_unmap(priv);
395}
396
397static void rcar_i2c_dma_callback(void *data)
398{
399 struct rcar_i2c_priv *priv = data;
400
401 priv->pos += sg_dma_len(&priv->sg);
402
403 rcar_i2c_dma_unmap(priv);
404}
405
406static bool rcar_i2c_dma(struct rcar_i2c_priv *priv)
407{
408 struct device *dev = rcar_i2c_priv_to_dev(priv);
409 struct i2c_msg *msg = priv->msg;
410 bool read = msg->flags & I2C_M_RD;
411 enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
412 struct dma_chan *chan = read ? priv->dma_rx : priv->dma_tx;
413 struct dma_async_tx_descriptor *txdesc;
414 dma_addr_t dma_addr;
415 dma_cookie_t cookie;
416 unsigned char *buf;
417 int len;
418
419 /* Do various checks to see if DMA is feasible at all */
420 if (IS_ERR(chan) || msg->len < RCAR_MIN_DMA_LEN ||
421 !(msg->flags & I2C_M_DMA_SAFE) || (read && priv->flags & ID_P_NO_RXDMA))
422 return false;
423
424 if (read) {
425 /*
426 * The last two bytes needs to be fetched using PIO in
427 * order for the STOP phase to work.
428 */
429 buf = priv->msg->buf;
430 len = priv->msg->len - 2;
431 } else {
432 /*
433 * First byte in message was sent using PIO.
434 */
435 buf = priv->msg->buf + 1;
436 len = priv->msg->len - 1;
437 }
438
439 dma_addr = dma_map_single(chan->device->dev, buf, len, dir);
440 if (dma_mapping_error(chan->device->dev, dma_addr)) {
441 dev_dbg(dev, "dma map failed, using PIO\n");
442 return false;
443 }
444
445 sg_dma_len(&priv->sg) = len;
446 sg_dma_address(&priv->sg) = dma_addr;
447
448 priv->dma_direction = dir;
449
450 txdesc = dmaengine_prep_slave_sg(chan, &priv->sg, 1,
451 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV,
452 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
453 if (!txdesc) {
454 dev_dbg(dev, "dma prep slave sg failed, using PIO\n");
455 rcar_i2c_cleanup_dma(priv);
456 return false;
457 }
458
459 txdesc->callback = rcar_i2c_dma_callback;
460 txdesc->callback_param = priv;
461
462 cookie = dmaengine_submit(txdesc);
463 if (dma_submit_error(cookie)) {
464 dev_dbg(dev, "submitting dma failed, using PIO\n");
465 rcar_i2c_cleanup_dma(priv);
466 return false;
467 }
468
469 /* Enable DMA Master Received/Transmitted */
470 if (read)
471 rcar_i2c_write(priv, ICDMAER, RMDMAE);
472 else
473 rcar_i2c_write(priv, ICDMAER, TMDMAE);
474
475 dma_async_issue_pending(chan);
476 return true;
477}
478
479static void rcar_i2c_irq_send(struct rcar_i2c_priv *priv, u32 msr)
480{
481 struct i2c_msg *msg = priv->msg;
482
483 /* FIXME: sometimes, unknown interrupt happened. Do nothing */
484 if (!(msr & MDE))
485 return;
486
487 /* Check if DMA can be enabled and take over */
488 if (priv->pos == 1 && rcar_i2c_dma(priv))
489 return;
490
491 if (priv->pos < msg->len) {
492 /*
493 * Prepare next data to ICRXTX register.
494 * This data will go to _SHIFT_ register.
495 *
496 * *
497 * [ICRXTX] -> [SHIFT] -> [I2C bus]
498 */
499 rcar_i2c_write(priv, ICRXTX, msg->buf[priv->pos]);
500 priv->pos++;
501 } else {
502 /*
503 * The last data was pushed to ICRXTX on _PREV_ empty irq.
504 * It is on _SHIFT_ register, and will sent to I2C bus.
505 *
506 * *
507 * [ICRXTX] -> [SHIFT] -> [I2C bus]
508 */
509
510 if (priv->flags & ID_LAST_MSG) {
511 /*
512 * If current msg is the _LAST_ msg,
513 * prepare stop condition here.
514 * ID_DONE will be set on STOP irq.
515 */
516 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
517 } else {
518 rcar_i2c_next_msg(priv);
519 return;
520 }
521 }
522
523 rcar_i2c_write(priv, ICMSR, RCAR_IRQ_ACK_SEND);
524}
525
526static void rcar_i2c_irq_recv(struct rcar_i2c_priv *priv, u32 msr)
527{
528 struct i2c_msg *msg = priv->msg;
529
530 /* FIXME: sometimes, unknown interrupt happened. Do nothing */
531 if (!(msr & MDR))
532 return;
533
534 if (msr & MAT) {
535 /*
536 * Address transfer phase finished, but no data at this point.
537 * Try to use DMA to receive data.
538 */
539 rcar_i2c_dma(priv);
540 } else if (priv->pos < msg->len) {
541 /* get received data */
542 msg->buf[priv->pos] = rcar_i2c_read(priv, ICRXTX);
543 priv->pos++;
544 }
545
546 /* If next received data is the _LAST_, go to new phase. */
547 if (priv->pos + 1 == msg->len) {
548 if (priv->flags & ID_LAST_MSG) {
549 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
550 } else {
551 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
552 priv->flags |= ID_P_REP_AFTER_RD;
553 }
554 }
555
556 if (priv->pos == msg->len && !(priv->flags & ID_LAST_MSG))
557 rcar_i2c_next_msg(priv);
558 else
559 rcar_i2c_write(priv, ICMSR, RCAR_IRQ_ACK_RECV);
560}
561
562static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
563{
564 u32 ssr_raw, ssr_filtered;
565 u8 value;
566
567 ssr_raw = rcar_i2c_read(priv, ICSSR) & 0xff;
568 ssr_filtered = ssr_raw & rcar_i2c_read(priv, ICSIER);
569
570 if (!ssr_filtered)
571 return false;
572
573 /* address detected */
574 if (ssr_filtered & SAR) {
575 /* read or write request */
576 if (ssr_raw & STM) {
577 i2c_slave_event(priv->slave, I2C_SLAVE_READ_REQUESTED, &value);
578 rcar_i2c_write(priv, ICRXTX, value);
579 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR);
580 } else {
581 i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
582 rcar_i2c_read(priv, ICRXTX); /* dummy read */
583 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR);
584 }
585
586 /* Clear SSR, too, because of old STOPs to other clients than us */
587 rcar_i2c_write(priv, ICSSR, ~(SAR | SSR) & 0xff);
588 }
589
590 /* master sent stop */
591 if (ssr_filtered & SSR) {
592 i2c_slave_event(priv->slave, I2C_SLAVE_STOP, &value);
593 rcar_i2c_write(priv, ICSCR, SIE | SDBS); /* clear our NACK */
594 rcar_i2c_write(priv, ICSIER, SAR);
595 rcar_i2c_write(priv, ICSSR, ~SSR & 0xff);
596 }
597
598 /* master wants to write to us */
599 if (ssr_filtered & SDR) {
600 int ret;
601
602 value = rcar_i2c_read(priv, ICRXTX);
603 ret = i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
604 /* Send NACK in case of error */
605 rcar_i2c_write(priv, ICSCR, SIE | SDBS | (ret < 0 ? FNA : 0));
606 rcar_i2c_write(priv, ICSSR, ~SDR & 0xff);
607 }
608
609 /* master wants to read from us */
610 if (ssr_filtered & SDE) {
611 i2c_slave_event(priv->slave, I2C_SLAVE_READ_PROCESSED, &value);
612 rcar_i2c_write(priv, ICRXTX, value);
613 rcar_i2c_write(priv, ICSSR, ~SDE & 0xff);
614 }
615
616 return true;
617}
618
619/*
620 * This driver has a lock-free design because there are IP cores (at least
621 * R-Car Gen2) which have an inherent race condition in their hardware design.
622 * There, we need to clear RCAR_BUS_MASK_DATA bits as soon as possible after
623 * the interrupt was generated, otherwise an unwanted repeated message gets
624 * generated. It turned out that taking a spinlock at the beginning of the ISR
625 * was already causing repeated messages. Thus, this driver was converted to
626 * the now lockless behaviour. Please keep this in mind when hacking the driver.
627 */
628static irqreturn_t rcar_i2c_irq(int irq, void *ptr)
629{
630 struct rcar_i2c_priv *priv = ptr;
631 u32 msr, val;
632
633 /* Clear START or STOP immediately, except for REPSTART after read */
634 if (likely(!(priv->flags & ID_P_REP_AFTER_RD))) {
635 val = rcar_i2c_read(priv, ICMCR);
636 rcar_i2c_write(priv, ICMCR, val & RCAR_BUS_MASK_DATA);
637 }
638
639 msr = rcar_i2c_read(priv, ICMSR);
640
641 /* Only handle interrupts that are currently enabled */
642 msr &= rcar_i2c_read(priv, ICMIER);
643 if (!msr) {
644 if (rcar_i2c_slave_irq(priv))
645 return IRQ_HANDLED;
646
647 return IRQ_NONE;
648 }
649
650 /* Arbitration lost */
651 if (msr & MAL) {
652 priv->flags |= ID_DONE | ID_ARBLOST;
653 goto out;
654 }
655
656 /* Nack */
657 if (msr & MNR) {
658 /* HW automatically sends STOP after received NACK */
659 rcar_i2c_write(priv, ICMIER, RCAR_IRQ_STOP);
660 priv->flags |= ID_NACK;
661 goto out;
662 }
663
664 /* Stop */
665 if (msr & MST) {
666 priv->msgs_left--; /* The last message also made it */
667 priv->flags |= ID_DONE;
668 goto out;
669 }
670
671 if (rcar_i2c_is_recv(priv))
672 rcar_i2c_irq_recv(priv, msr);
673 else
674 rcar_i2c_irq_send(priv, msr);
675
676out:
677 if (priv->flags & ID_DONE) {
678 rcar_i2c_write(priv, ICMIER, 0);
679 rcar_i2c_write(priv, ICMSR, 0);
680 wake_up(&priv->wait);
681 }
682
683 return IRQ_HANDLED;
684}
685
686static struct dma_chan *rcar_i2c_request_dma_chan(struct device *dev,
687 enum dma_transfer_direction dir,
688 dma_addr_t port_addr)
689{
690 struct dma_chan *chan;
691 struct dma_slave_config cfg;
692 char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx";
693 int ret;
694
695 chan = dma_request_chan(dev, chan_name);
696 if (IS_ERR(chan)) {
697 dev_dbg(dev, "request_channel failed for %s (%ld)\n",
698 chan_name, PTR_ERR(chan));
699 return chan;
700 }
701
702 memset(&cfg, 0, sizeof(cfg));
703 cfg.direction = dir;
704 if (dir == DMA_MEM_TO_DEV) {
705 cfg.dst_addr = port_addr;
706 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
707 } else {
708 cfg.src_addr = port_addr;
709 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
710 }
711
712 ret = dmaengine_slave_config(chan, &cfg);
713 if (ret) {
714 dev_dbg(dev, "slave_config failed for %s (%d)\n",
715 chan_name, ret);
716 dma_release_channel(chan);
717 return ERR_PTR(ret);
718 }
719
720 dev_dbg(dev, "got DMA channel for %s\n", chan_name);
721 return chan;
722}
723
724static void rcar_i2c_request_dma(struct rcar_i2c_priv *priv,
725 struct i2c_msg *msg)
726{
727 struct device *dev = rcar_i2c_priv_to_dev(priv);
728 bool read;
729 struct dma_chan *chan;
730 enum dma_transfer_direction dir;
731
732 read = msg->flags & I2C_M_RD;
733
734 chan = read ? priv->dma_rx : priv->dma_tx;
735 if (PTR_ERR(chan) != -EPROBE_DEFER)
736 return;
737
738 dir = read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV;
739 chan = rcar_i2c_request_dma_chan(dev, dir, priv->res->start + ICRXTX);
740
741 if (read)
742 priv->dma_rx = chan;
743 else
744 priv->dma_tx = chan;
745}
746
747static void rcar_i2c_release_dma(struct rcar_i2c_priv *priv)
748{
749 if (!IS_ERR(priv->dma_tx)) {
750 dma_release_channel(priv->dma_tx);
751 priv->dma_tx = ERR_PTR(-EPROBE_DEFER);
752 }
753
754 if (!IS_ERR(priv->dma_rx)) {
755 dma_release_channel(priv->dma_rx);
756 priv->dma_rx = ERR_PTR(-EPROBE_DEFER);
757 }
758}
759
760/* I2C is a special case, we need to poll the status of a reset */
761static int rcar_i2c_do_reset(struct rcar_i2c_priv *priv)
762{
763 int i, ret;
764
765 ret = reset_control_reset(priv->rstc);
766 if (ret)
767 return ret;
768
769 for (i = 0; i < LOOP_TIMEOUT; i++) {
770 ret = reset_control_status(priv->rstc);
771 if (ret == 0)
772 return 0;
773 udelay(1);
774 }
775
776 return -ETIMEDOUT;
777}
778
779static int rcar_i2c_master_xfer(struct i2c_adapter *adap,
780 struct i2c_msg *msgs,
781 int num)
782{
783 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
784 struct device *dev = rcar_i2c_priv_to_dev(priv);
785 int i, ret;
786 long time_left;
787
788 pm_runtime_get_sync(dev);
789
790 /* Check bus state before init otherwise bus busy info will be lost */
791 ret = rcar_i2c_bus_barrier(priv);
792 if (ret < 0)
793 goto out;
794
795 /* Gen3 needs a reset before allowing RXDMA once */
796 if (priv->devtype == I2C_RCAR_GEN3) {
797 priv->flags |= ID_P_NO_RXDMA;
798 if (!IS_ERR(priv->rstc)) {
799 ret = rcar_i2c_do_reset(priv);
800 if (ret == 0)
801 priv->flags &= ~ID_P_NO_RXDMA;
802 }
803 }
804
805 rcar_i2c_init(priv);
806
807 for (i = 0; i < num; i++)
808 rcar_i2c_request_dma(priv, msgs + i);
809
810 /* init first message */
811 priv->msg = msgs;
812 priv->msgs_left = num;
813 priv->flags = (priv->flags & ID_P_MASK) | ID_FIRST_MSG;
814 rcar_i2c_prepare_msg(priv);
815
816 time_left = wait_event_timeout(priv->wait, priv->flags & ID_DONE,
817 num * adap->timeout);
818
819 /* cleanup DMA if it couldn't complete properly due to an error */
820 if (priv->dma_direction != DMA_NONE)
821 rcar_i2c_cleanup_dma(priv);
822
823 if (!time_left) {
824 rcar_i2c_init(priv);
825 ret = -ETIMEDOUT;
826 } else if (priv->flags & ID_NACK) {
827 ret = -ENXIO;
828 } else if (priv->flags & ID_ARBLOST) {
829 ret = -EAGAIN;
830 } else {
831 ret = num - priv->msgs_left; /* The number of transfer */
832 }
833out:
834 pm_runtime_put(dev);
835
836 if (ret < 0 && ret != -ENXIO)
837 dev_err(dev, "error %d : %x\n", ret, priv->flags);
838
839 return ret;
840}
841
842static int rcar_reg_slave(struct i2c_client *slave)
843{
844 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter);
845
846 if (priv->slave)
847 return -EBUSY;
848
849 if (slave->flags & I2C_CLIENT_TEN)
850 return -EAFNOSUPPORT;
851
852 /* Keep device active for slave address detection logic */
853 pm_runtime_get_sync(rcar_i2c_priv_to_dev(priv));
854
855 priv->slave = slave;
856 rcar_i2c_write(priv, ICSAR, slave->addr);
857 rcar_i2c_write(priv, ICSSR, 0);
858 rcar_i2c_write(priv, ICSIER, SAR);
859 rcar_i2c_write(priv, ICSCR, SIE | SDBS);
860
861 return 0;
862}
863
864static int rcar_unreg_slave(struct i2c_client *slave)
865{
866 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter);
867
868 WARN_ON(!priv->slave);
869
870 /* ensure no irq is running before clearing ptr */
871 disable_irq(priv->irq);
872 rcar_i2c_write(priv, ICSIER, 0);
873 rcar_i2c_write(priv, ICSSR, 0);
874 enable_irq(priv->irq);
875 rcar_i2c_write(priv, ICSCR, SDBS);
876 rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
877
878 priv->slave = NULL;
879
880 pm_runtime_put(rcar_i2c_priv_to_dev(priv));
881
882 return 0;
883}
884
885static u32 rcar_i2c_func(struct i2c_adapter *adap)
886{
887 /*
888 * This HW can't do:
889 * I2C_SMBUS_QUICK (setting FSB during START didn't work)
890 * I2C_M_NOSTART (automatically sends address after START)
891 * I2C_M_IGNORE_NAK (automatically sends STOP after NAK)
892 */
893 return I2C_FUNC_I2C | I2C_FUNC_SLAVE |
894 (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
895}
896
897static const struct i2c_algorithm rcar_i2c_algo = {
898 .master_xfer = rcar_i2c_master_xfer,
899 .functionality = rcar_i2c_func,
900 .reg_slave = rcar_reg_slave,
901 .unreg_slave = rcar_unreg_slave,
902};
903
904static const struct i2c_adapter_quirks rcar_i2c_quirks = {
905 .flags = I2C_AQ_NO_ZERO_LEN,
906};
907
908static const struct of_device_id rcar_i2c_dt_ids[] = {
909 { .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 },
910 { .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 },
911 { .compatible = "renesas,i2c-r8a7790", .data = (void *)I2C_RCAR_GEN2 },
912 { .compatible = "renesas,i2c-r8a7791", .data = (void *)I2C_RCAR_GEN2 },
913 { .compatible = "renesas,i2c-r8a7792", .data = (void *)I2C_RCAR_GEN2 },
914 { .compatible = "renesas,i2c-r8a7793", .data = (void *)I2C_RCAR_GEN2 },
915 { .compatible = "renesas,i2c-r8a7794", .data = (void *)I2C_RCAR_GEN2 },
916 { .compatible = "renesas,i2c-r8a7795", .data = (void *)I2C_RCAR_GEN3 },
917 { .compatible = "renesas,i2c-r8a7796", .data = (void *)I2C_RCAR_GEN3 },
918 { .compatible = "renesas,i2c-rcar", .data = (void *)I2C_RCAR_GEN1 }, /* Deprecated */
919 { .compatible = "renesas,rcar-gen1-i2c", .data = (void *)I2C_RCAR_GEN1 },
920 { .compatible = "renesas,rcar-gen2-i2c", .data = (void *)I2C_RCAR_GEN2 },
921 { .compatible = "renesas,rcar-gen3-i2c", .data = (void *)I2C_RCAR_GEN3 },
922 {},
923};
924MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids);
925
926static int rcar_i2c_probe(struct platform_device *pdev)
927{
928 struct rcar_i2c_priv *priv;
929 struct i2c_adapter *adap;
930 struct device *dev = &pdev->dev;
931 int ret;
932
933 /* Otherwise logic will break because some bytes must always use PIO */
934 BUILD_BUG_ON_MSG(RCAR_MIN_DMA_LEN < 3, "Invalid min DMA length");
935
936 priv = devm_kzalloc(dev, sizeof(struct rcar_i2c_priv), GFP_KERNEL);
937 if (!priv)
938 return -ENOMEM;
939
940 priv->clk = devm_clk_get(dev, NULL);
941 if (IS_ERR(priv->clk)) {
942 dev_err(dev, "cannot get clock\n");
943 return PTR_ERR(priv->clk);
944 }
945
946 priv->io = devm_platform_get_and_ioremap_resource(pdev, 0, &priv->res);
947 if (IS_ERR(priv->io))
948 return PTR_ERR(priv->io);
949
950 priv->devtype = (enum rcar_i2c_type)of_device_get_match_data(dev);
951 init_waitqueue_head(&priv->wait);
952
953 adap = &priv->adap;
954 adap->nr = pdev->id;
955 adap->algo = &rcar_i2c_algo;
956 adap->class = I2C_CLASS_DEPRECATED;
957 adap->retries = 3;
958 adap->dev.parent = dev;
959 adap->dev.of_node = dev->of_node;
960 adap->bus_recovery_info = &rcar_i2c_bri;
961 adap->quirks = &rcar_i2c_quirks;
962 i2c_set_adapdata(adap, priv);
963 strlcpy(adap->name, pdev->name, sizeof(adap->name));
964
965 /* Init DMA */
966 sg_init_table(&priv->sg, 1);
967 priv->dma_direction = DMA_NONE;
968 priv->dma_rx = priv->dma_tx = ERR_PTR(-EPROBE_DEFER);
969
970 /* Activate device for clock calculation */
971 pm_runtime_enable(dev);
972 pm_runtime_get_sync(dev);
973 ret = rcar_i2c_clock_calculate(priv);
974 if (ret < 0)
975 goto out_pm_put;
976
977 rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
978
979 if (priv->devtype == I2C_RCAR_GEN3) {
980 priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
981 if (!IS_ERR(priv->rstc)) {
982 ret = reset_control_status(priv->rstc);
983 if (ret < 0)
984 priv->rstc = ERR_PTR(-ENOTSUPP);
985 }
986 }
987
988 /* Stay always active when multi-master to keep arbitration working */
989 if (of_property_read_bool(dev->of_node, "multi-master"))
990 priv->flags |= ID_P_PM_BLOCKED;
991 else
992 pm_runtime_put(dev);
993
994
995 priv->irq = platform_get_irq(pdev, 0);
996 ret = devm_request_irq(dev, priv->irq, rcar_i2c_irq, 0, dev_name(dev), priv);
997 if (ret < 0) {
998 dev_err(dev, "cannot get irq %d\n", priv->irq);
999 goto out_pm_disable;
1000 }
1001
1002 platform_set_drvdata(pdev, priv);
1003
1004 ret = i2c_add_numbered_adapter(adap);
1005 if (ret < 0)
1006 goto out_pm_disable;
1007
1008 dev_info(dev, "probed\n");
1009
1010 return 0;
1011
1012 out_pm_put:
1013 pm_runtime_put(dev);
1014 out_pm_disable:
1015 pm_runtime_disable(dev);
1016 return ret;
1017}
1018
1019static int rcar_i2c_remove(struct platform_device *pdev)
1020{
1021 struct rcar_i2c_priv *priv = platform_get_drvdata(pdev);
1022 struct device *dev = &pdev->dev;
1023
1024 i2c_del_adapter(&priv->adap);
1025 rcar_i2c_release_dma(priv);
1026 if (priv->flags & ID_P_PM_BLOCKED)
1027 pm_runtime_put(dev);
1028 pm_runtime_disable(dev);
1029
1030 return 0;
1031}
1032
1033#ifdef CONFIG_PM_SLEEP
1034static int rcar_i2c_suspend(struct device *dev)
1035{
1036 struct rcar_i2c_priv *priv = dev_get_drvdata(dev);
1037
1038 i2c_mark_adapter_suspended(&priv->adap);
1039 return 0;
1040}
1041
1042static int rcar_i2c_resume(struct device *dev)
1043{
1044 struct rcar_i2c_priv *priv = dev_get_drvdata(dev);
1045
1046 i2c_mark_adapter_resumed(&priv->adap);
1047 return 0;
1048}
1049
1050static const struct dev_pm_ops rcar_i2c_pm_ops = {
1051 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(rcar_i2c_suspend, rcar_i2c_resume)
1052};
1053
1054#define DEV_PM_OPS (&rcar_i2c_pm_ops)
1055#else
1056#define DEV_PM_OPS NULL
1057#endif /* CONFIG_PM_SLEEP */
1058
1059static struct platform_driver rcar_i2c_driver = {
1060 .driver = {
1061 .name = "i2c-rcar",
1062 .of_match_table = rcar_i2c_dt_ids,
1063 .pm = DEV_PM_OPS,
1064 },
1065 .probe = rcar_i2c_probe,
1066 .remove = rcar_i2c_remove,
1067};
1068
1069module_platform_driver(rcar_i2c_driver);
1070
1071MODULE_LICENSE("GPL v2");
1072MODULE_DESCRIPTION("Renesas R-Car I2C bus driver");
1073MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");