Loading...
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2018 Intel Corporation */
3
4#include <linux/delay.h>
5
6#include "igc_hw.h"
7#include "igc_i225.h"
8#include "igc_mac.h"
9#include "igc_base.h"
10#include "igc.h"
11
12/**
13 * igc_reset_hw_base - Reset hardware
14 * @hw: pointer to the HW structure
15 *
16 * This resets the hardware into a known state. This is a
17 * function pointer entry point called by the api module.
18 */
19static s32 igc_reset_hw_base(struct igc_hw *hw)
20{
21 s32 ret_val;
22 u32 ctrl;
23
24 /* Prevent the PCI-E bus from sticking if there is no TLP connection
25 * on the last TLP read/write transaction when MAC is reset.
26 */
27 ret_val = igc_disable_pcie_master(hw);
28 if (ret_val)
29 hw_dbg("PCI-E Master disable polling has failed\n");
30
31 hw_dbg("Masking off all interrupts\n");
32 wr32(IGC_IMC, 0xffffffff);
33
34 wr32(IGC_RCTL, 0);
35 wr32(IGC_TCTL, IGC_TCTL_PSP);
36 wrfl();
37
38 usleep_range(10000, 20000);
39
40 ctrl = rd32(IGC_CTRL);
41
42 hw_dbg("Issuing a global reset to MAC\n");
43 wr32(IGC_CTRL, ctrl | IGC_CTRL_RST);
44
45 ret_val = igc_get_auto_rd_done(hw);
46 if (ret_val) {
47 /* When auto config read does not complete, do not
48 * return with an error. This can happen in situations
49 * where there is no eeprom and prevents getting link.
50 */
51 hw_dbg("Auto Read Done did not complete\n");
52 }
53
54 /* Clear any pending interrupt events. */
55 wr32(IGC_IMC, 0xffffffff);
56 rd32(IGC_ICR);
57
58 return ret_val;
59}
60
61/**
62 * igc_init_nvm_params_base - Init NVM func ptrs.
63 * @hw: pointer to the HW structure
64 */
65static s32 igc_init_nvm_params_base(struct igc_hw *hw)
66{
67 struct igc_nvm_info *nvm = &hw->nvm;
68 u32 eecd = rd32(IGC_EECD);
69 u16 size;
70
71 size = FIELD_GET(IGC_EECD_SIZE_EX_MASK, eecd);
72
73 /* Added to a constant, "size" becomes the left-shift value
74 * for setting word_size.
75 */
76 size += NVM_WORD_SIZE_BASE_SHIFT;
77
78 /* Just in case size is out of range, cap it to the largest
79 * EEPROM size supported
80 */
81 if (size > 15)
82 size = 15;
83
84 nvm->type = igc_nvm_eeprom_spi;
85 nvm->word_size = BIT(size);
86 nvm->opcode_bits = 8;
87 nvm->delay_usec = 1;
88
89 nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8;
90 nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ?
91 16 : 8;
92
93 if (nvm->word_size == BIT(15))
94 nvm->page_size = 128;
95
96 return 0;
97}
98
99/**
100 * igc_setup_copper_link_base - Configure copper link settings
101 * @hw: pointer to the HW structure
102 *
103 * Configures the link for auto-neg or forced speed and duplex. Then we check
104 * for link, once link is established calls to configure collision distance
105 * and flow control are called.
106 */
107static s32 igc_setup_copper_link_base(struct igc_hw *hw)
108{
109 s32 ret_val = 0;
110 u32 ctrl;
111
112 ctrl = rd32(IGC_CTRL);
113 ctrl |= IGC_CTRL_SLU;
114 ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
115 wr32(IGC_CTRL, ctrl);
116
117 ret_val = igc_setup_copper_link(hw);
118
119 return ret_val;
120}
121
122/**
123 * igc_init_mac_params_base - Init MAC func ptrs.
124 * @hw: pointer to the HW structure
125 */
126static s32 igc_init_mac_params_base(struct igc_hw *hw)
127{
128 struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base;
129 struct igc_mac_info *mac = &hw->mac;
130
131 /* Set mta register count */
132 mac->mta_reg_count = 128;
133 mac->rar_entry_count = IGC_RAR_ENTRIES;
134
135 /* reset */
136 mac->ops.reset_hw = igc_reset_hw_base;
137
138 mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225;
139 mac->ops.release_swfw_sync = igc_release_swfw_sync_i225;
140
141 /* Allow a single clear of the SW semaphore on I225 */
142 if (mac->type == igc_i225)
143 dev_spec->clear_semaphore_once = true;
144
145 /* physical interface link setup */
146 mac->ops.setup_physical_interface = igc_setup_copper_link_base;
147
148 return 0;
149}
150
151/**
152 * igc_init_phy_params_base - Init PHY func ptrs.
153 * @hw: pointer to the HW structure
154 */
155static s32 igc_init_phy_params_base(struct igc_hw *hw)
156{
157 struct igc_phy_info *phy = &hw->phy;
158 s32 ret_val = 0;
159
160 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
161 phy->reset_delay_us = 100;
162
163 /* set lan id */
164 hw->bus.func = FIELD_GET(IGC_STATUS_FUNC_MASK, rd32(IGC_STATUS));
165
166 /* Make sure the PHY is in a good state. Several people have reported
167 * firmware leaving the PHY's page select register set to something
168 * other than the default of zero, which causes the PHY ID read to
169 * access something other than the intended register.
170 */
171 ret_val = hw->phy.ops.reset(hw);
172 if (ret_val) {
173 hw_dbg("Error resetting the PHY\n");
174 goto out;
175 }
176
177 ret_val = igc_get_phy_id(hw);
178 if (ret_val)
179 return ret_val;
180
181 igc_check_for_copper_link(hw);
182
183out:
184 return ret_val;
185}
186
187static s32 igc_get_invariants_base(struct igc_hw *hw)
188{
189 struct igc_mac_info *mac = &hw->mac;
190 s32 ret_val = 0;
191
192 switch (hw->device_id) {
193 case IGC_DEV_ID_I225_LM:
194 case IGC_DEV_ID_I225_V:
195 case IGC_DEV_ID_I225_I:
196 case IGC_DEV_ID_I220_V:
197 case IGC_DEV_ID_I225_K:
198 case IGC_DEV_ID_I225_K2:
199 case IGC_DEV_ID_I226_K:
200 case IGC_DEV_ID_I225_LMVP:
201 case IGC_DEV_ID_I226_LMVP:
202 case IGC_DEV_ID_I225_IT:
203 case IGC_DEV_ID_I226_LM:
204 case IGC_DEV_ID_I226_V:
205 case IGC_DEV_ID_I226_IT:
206 case IGC_DEV_ID_I221_V:
207 case IGC_DEV_ID_I226_BLANK_NVM:
208 case IGC_DEV_ID_I225_BLANK_NVM:
209 mac->type = igc_i225;
210 break;
211 default:
212 return -IGC_ERR_MAC_INIT;
213 }
214
215 hw->phy.media_type = igc_media_type_copper;
216
217 /* mac initialization and operations */
218 ret_val = igc_init_mac_params_base(hw);
219 if (ret_val)
220 goto out;
221
222 /* NVM initialization */
223 ret_val = igc_init_nvm_params_base(hw);
224 switch (hw->mac.type) {
225 case igc_i225:
226 ret_val = igc_init_nvm_params_i225(hw);
227 break;
228 default:
229 break;
230 }
231
232 /* setup PHY parameters */
233 ret_val = igc_init_phy_params_base(hw);
234 if (ret_val)
235 goto out;
236
237out:
238 return ret_val;
239}
240
241/**
242 * igc_acquire_phy_base - Acquire rights to access PHY
243 * @hw: pointer to the HW structure
244 *
245 * Acquire access rights to the correct PHY. This is a
246 * function pointer entry point called by the api module.
247 */
248static s32 igc_acquire_phy_base(struct igc_hw *hw)
249{
250 u16 mask = IGC_SWFW_PHY0_SM;
251
252 return hw->mac.ops.acquire_swfw_sync(hw, mask);
253}
254
255/**
256 * igc_release_phy_base - Release rights to access PHY
257 * @hw: pointer to the HW structure
258 *
259 * A wrapper to release access rights to the correct PHY. This is a
260 * function pointer entry point called by the api module.
261 */
262static void igc_release_phy_base(struct igc_hw *hw)
263{
264 u16 mask = IGC_SWFW_PHY0_SM;
265
266 hw->mac.ops.release_swfw_sync(hw, mask);
267}
268
269/**
270 * igc_init_hw_base - Initialize hardware
271 * @hw: pointer to the HW structure
272 *
273 * This inits the hardware readying it for operation.
274 */
275static s32 igc_init_hw_base(struct igc_hw *hw)
276{
277 struct igc_mac_info *mac = &hw->mac;
278 u16 i, rar_count = mac->rar_entry_count;
279 s32 ret_val = 0;
280
281 /* Setup the receive address */
282 igc_init_rx_addrs(hw, rar_count);
283
284 /* Zero out the Multicast HASH table */
285 hw_dbg("Zeroing the MTA\n");
286 for (i = 0; i < mac->mta_reg_count; i++)
287 array_wr32(IGC_MTA, i, 0);
288
289 /* Zero out the Unicast HASH table */
290 hw_dbg("Zeroing the UTA\n");
291 for (i = 0; i < mac->uta_reg_count; i++)
292 array_wr32(IGC_UTA, i, 0);
293
294 /* Setup link and flow control */
295 ret_val = igc_setup_link(hw);
296
297 /* Clear all of the statistics registers (clear on read). It is
298 * important that we do this after we have tried to establish link
299 * because the symbol error count will increment wildly if there
300 * is no link.
301 */
302 igc_clear_hw_cntrs_base(hw);
303
304 return ret_val;
305}
306
307/**
308 * igc_power_down_phy_copper_base - Remove link during PHY power down
309 * @hw: pointer to the HW structure
310 *
311 * In the case of a PHY power down to save power, or to turn off link during a
312 * driver unload, or wake on lan is not enabled, remove the link.
313 */
314void igc_power_down_phy_copper_base(struct igc_hw *hw)
315{
316 /* If the management interface is not enabled, then power down */
317 if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
318 igc_power_down_phy_copper(hw);
319}
320
321/**
322 * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
323 * @hw: pointer to the HW structure
324 *
325 * After Rx enable, if manageability is enabled then there is likely some
326 * bad data at the start of the fifo and possibly in the DMA fifo. This
327 * function clears the fifos and flushes any packets that came in as rx was
328 * being enabled.
329 */
330void igc_rx_fifo_flush_base(struct igc_hw *hw)
331{
332 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
333 int i, ms_wait;
334
335 /* disable IPv6 options as per hardware errata */
336 rfctl = rd32(IGC_RFCTL);
337 rfctl |= IGC_RFCTL_IPV6_EX_DIS;
338 wr32(IGC_RFCTL, rfctl);
339
340 if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN))
341 return;
342
343 /* Disable all Rx queues */
344 for (i = 0; i < 4; i++) {
345 rxdctl[i] = rd32(IGC_RXDCTL(i));
346 wr32(IGC_RXDCTL(i),
347 rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE);
348 }
349 /* Poll all queues to verify they have shut down */
350 for (ms_wait = 0; ms_wait < 10; ms_wait++) {
351 usleep_range(1000, 2000);
352 rx_enabled = 0;
353 for (i = 0; i < 4; i++)
354 rx_enabled |= rd32(IGC_RXDCTL(i));
355 if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE))
356 break;
357 }
358
359 if (ms_wait == 10)
360 hw_dbg("Queue disable timed out after 10ms\n");
361
362 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
363 * incoming packets are rejected. Set enable and wait 2ms so that
364 * any packet that was coming in as RCTL.EN was set is flushed
365 */
366 wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF);
367
368 rlpml = rd32(IGC_RLPML);
369 wr32(IGC_RLPML, 0);
370
371 rctl = rd32(IGC_RCTL);
372 temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP);
373 temp_rctl |= IGC_RCTL_LPE;
374
375 wr32(IGC_RCTL, temp_rctl);
376 wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN);
377 wrfl();
378 usleep_range(2000, 3000);
379
380 /* Enable Rx queues that were previously enabled and restore our
381 * previous state
382 */
383 for (i = 0; i < 4; i++)
384 wr32(IGC_RXDCTL(i), rxdctl[i]);
385 wr32(IGC_RCTL, rctl);
386 wrfl();
387
388 wr32(IGC_RLPML, rlpml);
389 wr32(IGC_RFCTL, rfctl);
390
391 /* Flush receive errors generated by workaround */
392 rd32(IGC_ROC);
393 rd32(IGC_RNBC);
394 rd32(IGC_MPC);
395}
396
397bool igc_is_device_id_i225(struct igc_hw *hw)
398{
399 switch (hw->device_id) {
400 case IGC_DEV_ID_I225_LM:
401 case IGC_DEV_ID_I225_V:
402 case IGC_DEV_ID_I225_I:
403 case IGC_DEV_ID_I225_K:
404 case IGC_DEV_ID_I225_K2:
405 case IGC_DEV_ID_I225_LMVP:
406 case IGC_DEV_ID_I225_IT:
407 return true;
408 default:
409 return false;
410 }
411}
412
413bool igc_is_device_id_i226(struct igc_hw *hw)
414{
415 switch (hw->device_id) {
416 case IGC_DEV_ID_I226_LM:
417 case IGC_DEV_ID_I226_V:
418 case IGC_DEV_ID_I226_K:
419 case IGC_DEV_ID_I226_IT:
420 return true;
421 default:
422 return false;
423 }
424}
425
426static struct igc_mac_operations igc_mac_ops_base = {
427 .init_hw = igc_init_hw_base,
428 .check_for_link = igc_check_for_copper_link,
429 .rar_set = igc_rar_set,
430 .read_mac_addr = igc_read_mac_addr,
431 .get_speed_and_duplex = igc_get_speed_and_duplex_copper,
432};
433
434static const struct igc_phy_operations igc_phy_ops_base = {
435 .acquire = igc_acquire_phy_base,
436 .release = igc_release_phy_base,
437 .reset = igc_phy_hw_reset,
438 .read_reg = igc_read_phy_reg_gpy,
439 .write_reg = igc_write_phy_reg_gpy,
440};
441
442const struct igc_info igc_base_info = {
443 .get_invariants = igc_get_invariants_base,
444 .mac_ops = &igc_mac_ops_base,
445 .phy_ops = &igc_phy_ops_base,
446};
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2018 Intel Corporation */
3
4#include <linux/delay.h>
5
6#include "igc_hw.h"
7#include "igc_i225.h"
8#include "igc_mac.h"
9#include "igc_base.h"
10#include "igc.h"
11
12/**
13 * igc_reset_hw_base - Reset hardware
14 * @hw: pointer to the HW structure
15 *
16 * This resets the hardware into a known state. This is a
17 * function pointer entry point called by the api module.
18 */
19static s32 igc_reset_hw_base(struct igc_hw *hw)
20{
21 s32 ret_val;
22 u32 ctrl;
23
24 /* Prevent the PCI-E bus from sticking if there is no TLP connection
25 * on the last TLP read/write transaction when MAC is reset.
26 */
27 ret_val = igc_disable_pcie_master(hw);
28 if (ret_val)
29 hw_dbg("PCI-E Master disable polling has failed.\n");
30
31 hw_dbg("Masking off all interrupts\n");
32 wr32(IGC_IMC, 0xffffffff);
33
34 wr32(IGC_RCTL, 0);
35 wr32(IGC_TCTL, IGC_TCTL_PSP);
36 wrfl();
37
38 usleep_range(10000, 20000);
39
40 ctrl = rd32(IGC_CTRL);
41
42 hw_dbg("Issuing a global reset to MAC\n");
43 wr32(IGC_CTRL, ctrl | IGC_CTRL_DEV_RST);
44
45 ret_val = igc_get_auto_rd_done(hw);
46 if (ret_val) {
47 /* When auto config read does not complete, do not
48 * return with an error. This can happen in situations
49 * where there is no eeprom and prevents getting link.
50 */
51 hw_dbg("Auto Read Done did not complete\n");
52 }
53
54 /* Clear any pending interrupt events. */
55 wr32(IGC_IMC, 0xffffffff);
56 rd32(IGC_ICR);
57
58 return ret_val;
59}
60
61/**
62 * igc_init_nvm_params_base - Init NVM func ptrs.
63 * @hw: pointer to the HW structure
64 */
65static s32 igc_init_nvm_params_base(struct igc_hw *hw)
66{
67 struct igc_nvm_info *nvm = &hw->nvm;
68 u32 eecd = rd32(IGC_EECD);
69 u16 size;
70
71 size = (u16)((eecd & IGC_EECD_SIZE_EX_MASK) >>
72 IGC_EECD_SIZE_EX_SHIFT);
73
74 /* Added to a constant, "size" becomes the left-shift value
75 * for setting word_size.
76 */
77 size += NVM_WORD_SIZE_BASE_SHIFT;
78
79 /* Just in case size is out of range, cap it to the largest
80 * EEPROM size supported
81 */
82 if (size > 15)
83 size = 15;
84
85 nvm->type = igc_nvm_eeprom_spi;
86 nvm->word_size = BIT(size);
87 nvm->opcode_bits = 8;
88 nvm->delay_usec = 1;
89
90 nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8;
91 nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ?
92 16 : 8;
93
94 if (nvm->word_size == BIT(15))
95 nvm->page_size = 128;
96
97 return 0;
98}
99
100/**
101 * igc_setup_copper_link_base - Configure copper link settings
102 * @hw: pointer to the HW structure
103 *
104 * Configures the link for auto-neg or forced speed and duplex. Then we check
105 * for link, once link is established calls to configure collision distance
106 * and flow control are called.
107 */
108static s32 igc_setup_copper_link_base(struct igc_hw *hw)
109{
110 s32 ret_val = 0;
111 u32 ctrl;
112
113 ctrl = rd32(IGC_CTRL);
114 ctrl |= IGC_CTRL_SLU;
115 ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
116 wr32(IGC_CTRL, ctrl);
117
118 ret_val = igc_setup_copper_link(hw);
119
120 return ret_val;
121}
122
123/**
124 * igc_init_mac_params_base - Init MAC func ptrs.
125 * @hw: pointer to the HW structure
126 */
127static s32 igc_init_mac_params_base(struct igc_hw *hw)
128{
129 struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base;
130 struct igc_mac_info *mac = &hw->mac;
131
132 /* Set mta register count */
133 mac->mta_reg_count = 128;
134 mac->rar_entry_count = IGC_RAR_ENTRIES;
135
136 /* reset */
137 mac->ops.reset_hw = igc_reset_hw_base;
138
139 mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225;
140 mac->ops.release_swfw_sync = igc_release_swfw_sync_i225;
141
142 /* Allow a single clear of the SW semaphore on I225 */
143 if (mac->type == igc_i225)
144 dev_spec->clear_semaphore_once = true;
145
146 /* physical interface link setup */
147 mac->ops.setup_physical_interface = igc_setup_copper_link_base;
148
149 return 0;
150}
151
152/**
153 * igc_init_phy_params_base - Init PHY func ptrs.
154 * @hw: pointer to the HW structure
155 */
156static s32 igc_init_phy_params_base(struct igc_hw *hw)
157{
158 struct igc_phy_info *phy = &hw->phy;
159 s32 ret_val = 0;
160
161 if (hw->phy.media_type != igc_media_type_copper) {
162 phy->type = igc_phy_none;
163 goto out;
164 }
165
166 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
167 phy->reset_delay_us = 100;
168
169 /* set lan id */
170 hw->bus.func = (rd32(IGC_STATUS) & IGC_STATUS_FUNC_MASK) >>
171 IGC_STATUS_FUNC_SHIFT;
172
173 /* Make sure the PHY is in a good state. Several people have reported
174 * firmware leaving the PHY's page select register set to something
175 * other than the default of zero, which causes the PHY ID read to
176 * access something other than the intended register.
177 */
178 ret_val = hw->phy.ops.reset(hw);
179 if (ret_val) {
180 hw_dbg("Error resetting the PHY.\n");
181 goto out;
182 }
183
184 ret_val = igc_get_phy_id(hw);
185 if (ret_val)
186 return ret_val;
187
188 igc_check_for_copper_link(hw);
189
190 /* Verify phy id and set remaining function pointers */
191 switch (phy->id) {
192 case I225_I_PHY_ID:
193 phy->type = igc_phy_i225;
194 break;
195 default:
196 ret_val = -IGC_ERR_PHY;
197 goto out;
198 }
199
200out:
201 return ret_val;
202}
203
204static s32 igc_get_invariants_base(struct igc_hw *hw)
205{
206 struct igc_mac_info *mac = &hw->mac;
207 s32 ret_val = 0;
208
209 switch (hw->device_id) {
210 case IGC_DEV_ID_I225_LM:
211 case IGC_DEV_ID_I225_V:
212 case IGC_DEV_ID_I225_I:
213 case IGC_DEV_ID_I220_V:
214 case IGC_DEV_ID_I225_K:
215 mac->type = igc_i225;
216 break;
217 default:
218 return -IGC_ERR_MAC_INIT;
219 }
220
221 hw->phy.media_type = igc_media_type_copper;
222
223 /* mac initialization and operations */
224 ret_val = igc_init_mac_params_base(hw);
225 if (ret_val)
226 goto out;
227
228 /* NVM initialization */
229 ret_val = igc_init_nvm_params_base(hw);
230 switch (hw->mac.type) {
231 case igc_i225:
232 ret_val = igc_init_nvm_params_i225(hw);
233 break;
234 default:
235 break;
236 }
237
238 /* setup PHY parameters */
239 ret_val = igc_init_phy_params_base(hw);
240 if (ret_val)
241 goto out;
242
243out:
244 return ret_val;
245}
246
247/**
248 * igc_acquire_phy_base - Acquire rights to access PHY
249 * @hw: pointer to the HW structure
250 *
251 * Acquire access rights to the correct PHY. This is a
252 * function pointer entry point called by the api module.
253 */
254static s32 igc_acquire_phy_base(struct igc_hw *hw)
255{
256 u16 mask = IGC_SWFW_PHY0_SM;
257
258 return hw->mac.ops.acquire_swfw_sync(hw, mask);
259}
260
261/**
262 * igc_release_phy_base - Release rights to access PHY
263 * @hw: pointer to the HW structure
264 *
265 * A wrapper to release access rights to the correct PHY. This is a
266 * function pointer entry point called by the api module.
267 */
268static void igc_release_phy_base(struct igc_hw *hw)
269{
270 u16 mask = IGC_SWFW_PHY0_SM;
271
272 hw->mac.ops.release_swfw_sync(hw, mask);
273}
274
275/**
276 * igc_init_hw_base - Initialize hardware
277 * @hw: pointer to the HW structure
278 *
279 * This inits the hardware readying it for operation.
280 */
281static s32 igc_init_hw_base(struct igc_hw *hw)
282{
283 struct igc_mac_info *mac = &hw->mac;
284 u16 i, rar_count = mac->rar_entry_count;
285 s32 ret_val = 0;
286
287 /* Setup the receive address */
288 igc_init_rx_addrs(hw, rar_count);
289
290 /* Zero out the Multicast HASH table */
291 hw_dbg("Zeroing the MTA\n");
292 for (i = 0; i < mac->mta_reg_count; i++)
293 array_wr32(IGC_MTA, i, 0);
294
295 /* Zero out the Unicast HASH table */
296 hw_dbg("Zeroing the UTA\n");
297 for (i = 0; i < mac->uta_reg_count; i++)
298 array_wr32(IGC_UTA, i, 0);
299
300 /* Setup link and flow control */
301 ret_val = igc_setup_link(hw);
302
303 /* Clear all of the statistics registers (clear on read). It is
304 * important that we do this after we have tried to establish link
305 * because the symbol error count will increment wildly if there
306 * is no link.
307 */
308 igc_clear_hw_cntrs_base(hw);
309
310 return ret_val;
311}
312
313/**
314 * igc_power_down_phy_copper_base - Remove link during PHY power down
315 * @hw: pointer to the HW structure
316 *
317 * In the case of a PHY power down to save power, or to turn off link during a
318 * driver unload, or wake on lan is not enabled, remove the link.
319 */
320void igc_power_down_phy_copper_base(struct igc_hw *hw)
321{
322 /* If the management interface is not enabled, then power down */
323 if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
324 igc_power_down_phy_copper(hw);
325}
326
327/**
328 * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
329 * @hw: pointer to the HW structure
330 *
331 * After Rx enable, if manageability is enabled then there is likely some
332 * bad data at the start of the fifo and possibly in the DMA fifo. This
333 * function clears the fifos and flushes any packets that came in as rx was
334 * being enabled.
335 */
336void igc_rx_fifo_flush_base(struct igc_hw *hw)
337{
338 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
339 int i, ms_wait;
340
341 /* disable IPv6 options as per hardware errata */
342 rfctl = rd32(IGC_RFCTL);
343 rfctl |= IGC_RFCTL_IPV6_EX_DIS;
344 wr32(IGC_RFCTL, rfctl);
345
346 if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN))
347 return;
348
349 /* Disable all Rx queues */
350 for (i = 0; i < 4; i++) {
351 rxdctl[i] = rd32(IGC_RXDCTL(i));
352 wr32(IGC_RXDCTL(i),
353 rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE);
354 }
355 /* Poll all queues to verify they have shut down */
356 for (ms_wait = 0; ms_wait < 10; ms_wait++) {
357 usleep_range(1000, 2000);
358 rx_enabled = 0;
359 for (i = 0; i < 4; i++)
360 rx_enabled |= rd32(IGC_RXDCTL(i));
361 if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE))
362 break;
363 }
364
365 if (ms_wait == 10)
366 pr_debug("Queue disable timed out after 10ms\n");
367
368 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
369 * incoming packets are rejected. Set enable and wait 2ms so that
370 * any packet that was coming in as RCTL.EN was set is flushed
371 */
372 wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF);
373
374 rlpml = rd32(IGC_RLPML);
375 wr32(IGC_RLPML, 0);
376
377 rctl = rd32(IGC_RCTL);
378 temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP);
379 temp_rctl |= IGC_RCTL_LPE;
380
381 wr32(IGC_RCTL, temp_rctl);
382 wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN);
383 wrfl();
384 usleep_range(2000, 3000);
385
386 /* Enable Rx queues that were previously enabled and restore our
387 * previous state
388 */
389 for (i = 0; i < 4; i++)
390 wr32(IGC_RXDCTL(i), rxdctl[i]);
391 wr32(IGC_RCTL, rctl);
392 wrfl();
393
394 wr32(IGC_RLPML, rlpml);
395 wr32(IGC_RFCTL, rfctl);
396
397 /* Flush receive errors generated by workaround */
398 rd32(IGC_ROC);
399 rd32(IGC_RNBC);
400 rd32(IGC_MPC);
401}
402
403static struct igc_mac_operations igc_mac_ops_base = {
404 .init_hw = igc_init_hw_base,
405 .check_for_link = igc_check_for_copper_link,
406 .rar_set = igc_rar_set,
407 .read_mac_addr = igc_read_mac_addr,
408 .get_speed_and_duplex = igc_get_speed_and_duplex_copper,
409};
410
411static const struct igc_phy_operations igc_phy_ops_base = {
412 .acquire = igc_acquire_phy_base,
413 .release = igc_release_phy_base,
414 .reset = igc_phy_hw_reset,
415 .read_reg = igc_read_phy_reg_gpy,
416 .write_reg = igc_write_phy_reg_gpy,
417};
418
419const struct igc_info igc_base_info = {
420 .get_invariants = igc_get_invariants_base,
421 .mac_ops = &igc_mac_ops_base,
422 .phy_ops = &igc_phy_ops_base,
423};