Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * linux/drivers/spi/spi-loopback-test.c
4 *
5 * (c) Martin Sperl <kernel@martin.sperl.org>
6 *
7 * Loopback test driver to test several typical spi_message conditions
8 * that a spi_master driver may encounter
9 * this can also get used for regression testing
10 */
11
12#include <linux/delay.h>
13#include <linux/kernel.h>
14#include <linux/ktime.h>
15#include <linux/list.h>
16#include <linux/list_sort.h>
17#include <linux/mod_devicetable.h>
18#include <linux/module.h>
19#include <linux/printk.h>
20#include <linux/vmalloc.h>
21#include <linux/spi/spi.h>
22
23#include "spi-test.h"
24
25/* flag to only simulate transfers */
26static int simulate_only;
27module_param(simulate_only, int, 0);
28MODULE_PARM_DESC(simulate_only, "if not 0 do not execute the spi message");
29
30/* dump spi messages */
31static int dump_messages;
32module_param(dump_messages, int, 0);
33MODULE_PARM_DESC(dump_messages,
34 "=1 dump the basic spi_message_structure, " \
35 "=2 dump the spi_message_structure including data, " \
36 "=3 dump the spi_message structure before and after execution");
37/* the device is jumpered for loopback - enabling some rx_buf tests */
38static int loopback;
39module_param(loopback, int, 0);
40MODULE_PARM_DESC(loopback,
41 "if set enable loopback mode, where the rx_buf " \
42 "is checked to match tx_buf after the spi_message " \
43 "is executed");
44
45static int loop_req;
46module_param(loop_req, int, 0);
47MODULE_PARM_DESC(loop_req,
48 "if set controller will be asked to enable test loop mode. " \
49 "If controller supported it, MISO and MOSI will be connected");
50
51static int no_cs;
52module_param(no_cs, int, 0);
53MODULE_PARM_DESC(no_cs,
54 "if set Chip Select (CS) will not be used");
55
56/* run tests only for a specific length */
57static int run_only_iter_len = -1;
58module_param(run_only_iter_len, int, 0);
59MODULE_PARM_DESC(run_only_iter_len,
60 "only run tests for a length of this number in iterate_len list");
61
62/* run only a specific test */
63static int run_only_test = -1;
64module_param(run_only_test, int, 0);
65MODULE_PARM_DESC(run_only_test,
66 "only run the test with this number (0-based !)");
67
68/* use vmalloc'ed buffers */
69static int use_vmalloc;
70module_param(use_vmalloc, int, 0644);
71MODULE_PARM_DESC(use_vmalloc,
72 "use vmalloc'ed buffers instead of kmalloc'ed");
73
74/* check rx ranges */
75static int check_ranges = 1;
76module_param(check_ranges, int, 0644);
77MODULE_PARM_DESC(check_ranges,
78 "checks rx_buffer pattern are valid");
79
80static unsigned int delay_ms = 100;
81module_param(delay_ms, uint, 0644);
82MODULE_PARM_DESC(delay_ms,
83 "delay between tests, in milliseconds (default: 100)");
84
85/* the actual tests to execute */
86static struct spi_test spi_tests[] = {
87 {
88 .description = "tx/rx-transfer - start of page",
89 .fill_option = FILL_COUNT_8,
90 .iterate_len = { ITERATE_MAX_LEN },
91 .iterate_tx_align = ITERATE_ALIGN,
92 .iterate_rx_align = ITERATE_ALIGN,
93 .transfer_count = 1,
94 .transfers = {
95 {
96 .tx_buf = TX(0),
97 .rx_buf = RX(0),
98 },
99 },
100 },
101 {
102 .description = "tx/rx-transfer - crossing PAGE_SIZE",
103 .fill_option = FILL_COUNT_8,
104 .iterate_len = { ITERATE_LEN },
105 .iterate_tx_align = ITERATE_ALIGN,
106 .iterate_rx_align = ITERATE_ALIGN,
107 .transfer_count = 1,
108 .transfers = {
109 {
110 .tx_buf = TX(PAGE_SIZE - 4),
111 .rx_buf = RX(PAGE_SIZE - 4),
112 },
113 },
114 },
115 {
116 .description = "tx-transfer - only",
117 .fill_option = FILL_COUNT_8,
118 .iterate_len = { ITERATE_MAX_LEN },
119 .iterate_tx_align = ITERATE_ALIGN,
120 .transfer_count = 1,
121 .transfers = {
122 {
123 .tx_buf = TX(0),
124 },
125 },
126 },
127 {
128 .description = "rx-transfer - only",
129 .fill_option = FILL_COUNT_8,
130 .iterate_len = { ITERATE_MAX_LEN },
131 .iterate_rx_align = ITERATE_ALIGN,
132 .transfer_count = 1,
133 .transfers = {
134 {
135 .rx_buf = RX(0),
136 },
137 },
138 },
139 {
140 .description = "two tx-transfers - alter both",
141 .fill_option = FILL_COUNT_8,
142 .iterate_len = { ITERATE_LEN },
143 .iterate_tx_align = ITERATE_ALIGN,
144 .iterate_transfer_mask = BIT(0) | BIT(1),
145 .transfer_count = 2,
146 .transfers = {
147 {
148 .tx_buf = TX(0),
149 },
150 {
151 /* this is why we cant use ITERATE_MAX_LEN */
152 .tx_buf = TX(SPI_TEST_MAX_SIZE_HALF),
153 },
154 },
155 },
156 {
157 .description = "two tx-transfers - alter first",
158 .fill_option = FILL_COUNT_8,
159 .iterate_len = { ITERATE_MAX_LEN },
160 .iterate_tx_align = ITERATE_ALIGN,
161 .iterate_transfer_mask = BIT(0),
162 .transfer_count = 2,
163 .transfers = {
164 {
165 .tx_buf = TX(64),
166 },
167 {
168 .len = 1,
169 .tx_buf = TX(0),
170 },
171 },
172 },
173 {
174 .description = "two tx-transfers - alter second",
175 .fill_option = FILL_COUNT_8,
176 .iterate_len = { ITERATE_MAX_LEN },
177 .iterate_tx_align = ITERATE_ALIGN,
178 .iterate_transfer_mask = BIT(1),
179 .transfer_count = 2,
180 .transfers = {
181 {
182 .len = 16,
183 .tx_buf = TX(0),
184 },
185 {
186 .tx_buf = TX(64),
187 },
188 },
189 },
190 {
191 .description = "two transfers tx then rx - alter both",
192 .fill_option = FILL_COUNT_8,
193 .iterate_len = { ITERATE_MAX_LEN },
194 .iterate_tx_align = ITERATE_ALIGN,
195 .iterate_transfer_mask = BIT(0) | BIT(1),
196 .transfer_count = 2,
197 .transfers = {
198 {
199 .tx_buf = TX(0),
200 },
201 {
202 .rx_buf = RX(0),
203 },
204 },
205 },
206 {
207 .description = "two transfers tx then rx - alter tx",
208 .fill_option = FILL_COUNT_8,
209 .iterate_len = { ITERATE_MAX_LEN },
210 .iterate_tx_align = ITERATE_ALIGN,
211 .iterate_transfer_mask = BIT(0),
212 .transfer_count = 2,
213 .transfers = {
214 {
215 .tx_buf = TX(0),
216 },
217 {
218 .len = 1,
219 .rx_buf = RX(0),
220 },
221 },
222 },
223 {
224 .description = "two transfers tx then rx - alter rx",
225 .fill_option = FILL_COUNT_8,
226 .iterate_len = { ITERATE_MAX_LEN },
227 .iterate_tx_align = ITERATE_ALIGN,
228 .iterate_transfer_mask = BIT(1),
229 .transfer_count = 2,
230 .transfers = {
231 {
232 .len = 1,
233 .tx_buf = TX(0),
234 },
235 {
236 .rx_buf = RX(0),
237 },
238 },
239 },
240 {
241 .description = "two tx+rx transfers - alter both",
242 .fill_option = FILL_COUNT_8,
243 .iterate_len = { ITERATE_LEN },
244 .iterate_tx_align = ITERATE_ALIGN,
245 .iterate_transfer_mask = BIT(0) | BIT(1),
246 .transfer_count = 2,
247 .transfers = {
248 {
249 .tx_buf = TX(0),
250 .rx_buf = RX(0),
251 },
252 {
253 /* making sure we align without overwrite
254 * the reason we can not use ITERATE_MAX_LEN
255 */
256 .tx_buf = TX(SPI_TEST_MAX_SIZE_HALF),
257 .rx_buf = RX(SPI_TEST_MAX_SIZE_HALF),
258 },
259 },
260 },
261 {
262 .description = "two tx+rx transfers - alter first",
263 .fill_option = FILL_COUNT_8,
264 .iterate_len = { ITERATE_MAX_LEN },
265 .iterate_tx_align = ITERATE_ALIGN,
266 .iterate_transfer_mask = BIT(0),
267 .transfer_count = 2,
268 .transfers = {
269 {
270 /* making sure we align without overwrite */
271 .tx_buf = TX(1024),
272 .rx_buf = RX(1024),
273 },
274 {
275 .len = 1,
276 /* making sure we align without overwrite */
277 .tx_buf = TX(0),
278 .rx_buf = RX(0),
279 },
280 },
281 },
282 {
283 .description = "two tx+rx transfers - alter second",
284 .fill_option = FILL_COUNT_8,
285 .iterate_len = { ITERATE_MAX_LEN },
286 .iterate_tx_align = ITERATE_ALIGN,
287 .iterate_transfer_mask = BIT(1),
288 .transfer_count = 2,
289 .transfers = {
290 {
291 .len = 1,
292 .tx_buf = TX(0),
293 .rx_buf = RX(0),
294 },
295 {
296 /* making sure we align without overwrite */
297 .tx_buf = TX(1024),
298 .rx_buf = RX(1024),
299 },
300 },
301 },
302 {
303 .description = "two tx+rx transfers - delay after transfer",
304 .fill_option = FILL_COUNT_8,
305 .iterate_len = { ITERATE_MAX_LEN },
306 .iterate_transfer_mask = BIT(0) | BIT(1),
307 .transfer_count = 2,
308 .transfers = {
309 {
310 .tx_buf = TX(0),
311 .rx_buf = RX(0),
312 .delay = {
313 .value = 1000,
314 .unit = SPI_DELAY_UNIT_USECS,
315 },
316 },
317 {
318 .tx_buf = TX(0),
319 .rx_buf = RX(0),
320 .delay = {
321 .value = 1000,
322 .unit = SPI_DELAY_UNIT_USECS,
323 },
324 },
325 },
326 },
327 {
328 .description = "three tx+rx transfers with overlapping cache lines",
329 .fill_option = FILL_COUNT_8,
330 /*
331 * This should be large enough for the controller driver to
332 * choose to transfer it with DMA.
333 */
334 .iterate_len = { 512, -1 },
335 .iterate_transfer_mask = BIT(1),
336 .transfer_count = 3,
337 .transfers = {
338 {
339 .len = 1,
340 .tx_buf = TX(0),
341 .rx_buf = RX(0),
342 },
343 {
344 .tx_buf = TX(1),
345 .rx_buf = RX(1),
346 },
347 {
348 .len = 1,
349 .tx_buf = TX(513),
350 .rx_buf = RX(513),
351 },
352 },
353 },
354
355 { /* end of tests sequence */ }
356};
357
358static int spi_loopback_test_probe(struct spi_device *spi)
359{
360 int ret;
361
362 if (loop_req || no_cs) {
363 spi->mode |= loop_req ? SPI_LOOP : 0;
364 spi->mode |= no_cs ? SPI_NO_CS : 0;
365 ret = spi_setup(spi);
366 if (ret) {
367 dev_err(&spi->dev, "SPI setup with SPI_LOOP or SPI_NO_CS failed (%d)\n",
368 ret);
369 return ret;
370 }
371 }
372
373 dev_info(&spi->dev, "Executing spi-loopback-tests\n");
374
375 ret = spi_test_run_tests(spi, spi_tests);
376
377 dev_info(&spi->dev, "Finished spi-loopback-tests with return: %i\n",
378 ret);
379
380 return ret;
381}
382
383/* non const match table to permit to change via a module parameter */
384static struct of_device_id spi_loopback_test_of_match[] = {
385 { .compatible = "linux,spi-loopback-test", },
386 { }
387};
388
389/* allow to override the compatible string via a module_parameter */
390module_param_string(compatible, spi_loopback_test_of_match[0].compatible,
391 sizeof(spi_loopback_test_of_match[0].compatible),
392 0000);
393
394MODULE_DEVICE_TABLE(of, spi_loopback_test_of_match);
395
396static struct spi_driver spi_loopback_test_driver = {
397 .driver = {
398 .name = "spi-loopback-test",
399 .owner = THIS_MODULE,
400 .of_match_table = spi_loopback_test_of_match,
401 },
402 .probe = spi_loopback_test_probe,
403};
404
405module_spi_driver(spi_loopback_test_driver);
406
407MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>");
408MODULE_DESCRIPTION("test spi_driver to check core functionality");
409MODULE_LICENSE("GPL");
410
411/*-------------------------------------------------------------------------*/
412
413/* spi_test implementation */
414
415#define RANGE_CHECK(ptr, plen, start, slen) \
416 ((ptr >= start) && (ptr + plen <= start + slen))
417
418/* we allocate one page more, to allow for offsets */
419#define SPI_TEST_MAX_SIZE_PLUS (SPI_TEST_MAX_SIZE + PAGE_SIZE)
420
421static void spi_test_print_hex_dump(char *pre, const void *ptr, size_t len)
422{
423 /* limit the hex_dump */
424 if (len < 1024) {
425 print_hex_dump(KERN_INFO, pre,
426 DUMP_PREFIX_OFFSET, 16, 1,
427 ptr, len, 0);
428 return;
429 }
430 /* print head */
431 print_hex_dump(KERN_INFO, pre,
432 DUMP_PREFIX_OFFSET, 16, 1,
433 ptr, 512, 0);
434 /* print tail */
435 pr_info("%s truncated - continuing at offset %04zx\n",
436 pre, len - 512);
437 print_hex_dump(KERN_INFO, pre,
438 DUMP_PREFIX_OFFSET, 16, 1,
439 ptr + (len - 512), 512, 0);
440}
441
442static void spi_test_dump_message(struct spi_device *spi,
443 struct spi_message *msg,
444 bool dump_data)
445{
446 struct spi_transfer *xfer;
447 int i;
448 u8 b;
449
450 dev_info(&spi->dev, " spi_msg@%pK\n", msg);
451 if (msg->status)
452 dev_info(&spi->dev, " status: %i\n",
453 msg->status);
454 dev_info(&spi->dev, " frame_length: %i\n",
455 msg->frame_length);
456 dev_info(&spi->dev, " actual_length: %i\n",
457 msg->actual_length);
458
459 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
460 dev_info(&spi->dev, " spi_transfer@%pK\n", xfer);
461 dev_info(&spi->dev, " len: %i\n", xfer->len);
462 dev_info(&spi->dev, " tx_buf: %pK\n", xfer->tx_buf);
463 if (dump_data && xfer->tx_buf)
464 spi_test_print_hex_dump(" TX: ",
465 xfer->tx_buf,
466 xfer->len);
467
468 dev_info(&spi->dev, " rx_buf: %pK\n", xfer->rx_buf);
469 if (dump_data && xfer->rx_buf)
470 spi_test_print_hex_dump(" RX: ",
471 xfer->rx_buf,
472 xfer->len);
473 /* check for unwritten test pattern on rx_buf */
474 if (xfer->rx_buf) {
475 for (i = 0 ; i < xfer->len ; i++) {
476 b = ((u8 *)xfer->rx_buf)[xfer->len - 1 - i];
477 if (b != SPI_TEST_PATTERN_UNWRITTEN)
478 break;
479 }
480 if (i)
481 dev_info(&spi->dev,
482 " rx_buf filled with %02x starts at offset: %i\n",
483 SPI_TEST_PATTERN_UNWRITTEN,
484 xfer->len - i);
485 }
486 }
487}
488
489struct rx_ranges {
490 struct list_head list;
491 u8 *start;
492 u8 *end;
493};
494
495static int rx_ranges_cmp(void *priv, const struct list_head *a,
496 const struct list_head *b)
497{
498 struct rx_ranges *rx_a = list_entry(a, struct rx_ranges, list);
499 struct rx_ranges *rx_b = list_entry(b, struct rx_ranges, list);
500
501 if (rx_a->start > rx_b->start)
502 return 1;
503 if (rx_a->start < rx_b->start)
504 return -1;
505 return 0;
506}
507
508static int spi_check_rx_ranges(struct spi_device *spi,
509 struct spi_message *msg,
510 void *rx)
511{
512 struct spi_transfer *xfer;
513 struct rx_ranges ranges[SPI_TEST_MAX_TRANSFERS], *r;
514 int i = 0;
515 LIST_HEAD(ranges_list);
516 u8 *addr;
517 int ret = 0;
518
519 /* loop over all transfers to fill in the rx_ranges */
520 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
521 /* if there is no rx, then no check is needed */
522 if (!xfer->rx_buf)
523 continue;
524 /* fill in the rx_range */
525 if (RANGE_CHECK(xfer->rx_buf, xfer->len,
526 rx, SPI_TEST_MAX_SIZE_PLUS)) {
527 ranges[i].start = xfer->rx_buf;
528 ranges[i].end = xfer->rx_buf + xfer->len;
529 list_add(&ranges[i].list, &ranges_list);
530 i++;
531 }
532 }
533
534 /* if no ranges, then we can return and avoid the checks...*/
535 if (!i)
536 return 0;
537
538 /* sort the list */
539 list_sort(NULL, &ranges_list, rx_ranges_cmp);
540
541 /* and iterate over all the rx addresses */
542 for (addr = rx; addr < (u8 *)rx + SPI_TEST_MAX_SIZE_PLUS; addr++) {
543 /* if we are the DO not write pattern,
544 * then continue with the loop...
545 */
546 if (*addr == SPI_TEST_PATTERN_DO_NOT_WRITE)
547 continue;
548
549 /* check if we are inside a range */
550 list_for_each_entry(r, &ranges_list, list) {
551 /* if so then set to end... */
552 if ((addr >= r->start) && (addr < r->end))
553 addr = r->end;
554 }
555 /* second test after a (hopefull) translation */
556 if (*addr == SPI_TEST_PATTERN_DO_NOT_WRITE)
557 continue;
558
559 /* if still not found then something has modified too much */
560 /* we could list the "closest" transfer here... */
561 dev_err(&spi->dev,
562 "loopback strangeness - rx changed outside of allowed range at: %pK\n",
563 addr);
564 /* do not return, only set ret,
565 * so that we list all addresses
566 */
567 ret = -ERANGE;
568 }
569
570 return ret;
571}
572
573static int spi_test_check_elapsed_time(struct spi_device *spi,
574 struct spi_test *test)
575{
576 int i;
577 unsigned long long estimated_time = 0;
578 unsigned long long delay_usecs = 0;
579
580 for (i = 0; i < test->transfer_count; i++) {
581 struct spi_transfer *xfer = test->transfers + i;
582 unsigned long long nbits = (unsigned long long)BITS_PER_BYTE *
583 xfer->len;
584
585 delay_usecs += xfer->delay.value;
586 if (!xfer->speed_hz)
587 continue;
588 estimated_time += div_u64(nbits * NSEC_PER_SEC, xfer->speed_hz);
589 }
590
591 estimated_time += delay_usecs * NSEC_PER_USEC;
592 if (test->elapsed_time < estimated_time) {
593 dev_err(&spi->dev,
594 "elapsed time %lld ns is shorter than minimum estimated time %lld ns\n",
595 test->elapsed_time, estimated_time);
596
597 return -EINVAL;
598 }
599
600 return 0;
601}
602
603static int spi_test_check_loopback_result(struct spi_device *spi,
604 struct spi_message *msg,
605 void *tx, void *rx)
606{
607 struct spi_transfer *xfer;
608 u8 rxb, txb;
609 size_t i;
610 int ret;
611
612 /* checks rx_buffer pattern are valid with loopback or without */
613 if (check_ranges) {
614 ret = spi_check_rx_ranges(spi, msg, rx);
615 if (ret)
616 return ret;
617 }
618
619 /* if we run without loopback, then return now */
620 if (!loopback)
621 return 0;
622
623 /* if applicable to transfer check that rx_buf is equal to tx_buf */
624 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
625 /* if there is no rx, then no check is needed */
626 if (!xfer->len || !xfer->rx_buf)
627 continue;
628 /* so depending on tx_buf we need to handle things */
629 if (xfer->tx_buf) {
630 for (i = 0; i < xfer->len; i++) {
631 txb = ((u8 *)xfer->tx_buf)[i];
632 rxb = ((u8 *)xfer->rx_buf)[i];
633 if (txb != rxb)
634 goto mismatch_error;
635 }
636 } else {
637 /* first byte received */
638 txb = ((u8 *)xfer->rx_buf)[0];
639 /* first byte may be 0 or xff */
640 if (!((txb == 0) || (txb == 0xff))) {
641 dev_err(&spi->dev,
642 "loopback strangeness - we expect 0x00 or 0xff, but not 0x%02x\n",
643 txb);
644 return -EINVAL;
645 }
646 /* check that all bytes are identical */
647 for (i = 1; i < xfer->len; i++) {
648 rxb = ((u8 *)xfer->rx_buf)[i];
649 if (rxb != txb)
650 goto mismatch_error;
651 }
652 }
653 }
654
655 return 0;
656
657mismatch_error:
658 dev_err(&spi->dev,
659 "loopback strangeness - transfer mismatch on byte %04zx - expected 0x%02x, but got 0x%02x\n",
660 i, txb, rxb);
661
662 return -EINVAL;
663}
664
665static int spi_test_translate(struct spi_device *spi,
666 void **ptr, size_t len,
667 void *tx, void *rx)
668{
669 size_t off;
670
671 /* return on null */
672 if (!*ptr)
673 return 0;
674
675 /* in the MAX_SIZE_HALF case modify the pointer */
676 if (((size_t)*ptr) & SPI_TEST_MAX_SIZE_HALF)
677 /* move the pointer to the correct range */
678 *ptr += (SPI_TEST_MAX_SIZE_PLUS / 2) -
679 SPI_TEST_MAX_SIZE_HALF;
680
681 /* RX range
682 * - we check against MAX_SIZE_PLUS to allow for automated alignment
683 */
684 if (RANGE_CHECK(*ptr, len, RX(0), SPI_TEST_MAX_SIZE_PLUS)) {
685 off = *ptr - RX(0);
686 *ptr = rx + off;
687
688 return 0;
689 }
690
691 /* TX range */
692 if (RANGE_CHECK(*ptr, len, TX(0), SPI_TEST_MAX_SIZE_PLUS)) {
693 off = *ptr - TX(0);
694 *ptr = tx + off;
695
696 return 0;
697 }
698
699 dev_err(&spi->dev,
700 "PointerRange [%pK:%pK[ not in range [%pK:%pK[ or [%pK:%pK[\n",
701 *ptr, *ptr + len,
702 RX(0), RX(SPI_TEST_MAX_SIZE),
703 TX(0), TX(SPI_TEST_MAX_SIZE));
704
705 return -EINVAL;
706}
707
708static int spi_test_fill_pattern(struct spi_device *spi,
709 struct spi_test *test)
710{
711 struct spi_transfer *xfers = test->transfers;
712 u8 *tx_buf;
713 size_t count = 0;
714 int i, j;
715
716#ifdef __BIG_ENDIAN
717#define GET_VALUE_BYTE(value, index, bytes) \
718 (value >> (8 * (bytes - 1 - count % bytes)))
719#else
720#define GET_VALUE_BYTE(value, index, bytes) \
721 (value >> (8 * (count % bytes)))
722#endif
723
724 /* fill all transfers with the pattern requested */
725 for (i = 0; i < test->transfer_count; i++) {
726 /* fill rx_buf with SPI_TEST_PATTERN_UNWRITTEN */
727 if (xfers[i].rx_buf)
728 memset(xfers[i].rx_buf, SPI_TEST_PATTERN_UNWRITTEN,
729 xfers[i].len);
730 /* if tx_buf is NULL then skip */
731 tx_buf = (u8 *)xfers[i].tx_buf;
732 if (!tx_buf)
733 continue;
734 /* modify all the transfers */
735 for (j = 0; j < xfers[i].len; j++, tx_buf++, count++) {
736 /* fill tx */
737 switch (test->fill_option) {
738 case FILL_MEMSET_8:
739 *tx_buf = test->fill_pattern;
740 break;
741 case FILL_MEMSET_16:
742 *tx_buf = GET_VALUE_BYTE(test->fill_pattern,
743 count, 2);
744 break;
745 case FILL_MEMSET_24:
746 *tx_buf = GET_VALUE_BYTE(test->fill_pattern,
747 count, 3);
748 break;
749 case FILL_MEMSET_32:
750 *tx_buf = GET_VALUE_BYTE(test->fill_pattern,
751 count, 4);
752 break;
753 case FILL_COUNT_8:
754 *tx_buf = count;
755 break;
756 case FILL_COUNT_16:
757 *tx_buf = GET_VALUE_BYTE(count, count, 2);
758 break;
759 case FILL_COUNT_24:
760 *tx_buf = GET_VALUE_BYTE(count, count, 3);
761 break;
762 case FILL_COUNT_32:
763 *tx_buf = GET_VALUE_BYTE(count, count, 4);
764 break;
765 case FILL_TRANSFER_BYTE_8:
766 *tx_buf = j;
767 break;
768 case FILL_TRANSFER_BYTE_16:
769 *tx_buf = GET_VALUE_BYTE(j, j, 2);
770 break;
771 case FILL_TRANSFER_BYTE_24:
772 *tx_buf = GET_VALUE_BYTE(j, j, 3);
773 break;
774 case FILL_TRANSFER_BYTE_32:
775 *tx_buf = GET_VALUE_BYTE(j, j, 4);
776 break;
777 case FILL_TRANSFER_NUM:
778 *tx_buf = i;
779 break;
780 default:
781 dev_err(&spi->dev,
782 "unsupported fill_option: %i\n",
783 test->fill_option);
784 return -EINVAL;
785 }
786 }
787 }
788
789 return 0;
790}
791
792static int _spi_test_run_iter(struct spi_device *spi,
793 struct spi_test *test,
794 void *tx, void *rx)
795{
796 struct spi_message *msg = &test->msg;
797 struct spi_transfer *x;
798 int i, ret;
799
800 /* initialize message - zero-filled via static initialization */
801 spi_message_init_no_memset(msg);
802
803 /* fill rx with the DO_NOT_WRITE pattern */
804 memset(rx, SPI_TEST_PATTERN_DO_NOT_WRITE, SPI_TEST_MAX_SIZE_PLUS);
805
806 /* add the individual transfers */
807 for (i = 0; i < test->transfer_count; i++) {
808 x = &test->transfers[i];
809
810 /* patch the values of tx_buf */
811 ret = spi_test_translate(spi, (void **)&x->tx_buf, x->len,
812 (void *)tx, rx);
813 if (ret)
814 return ret;
815
816 /* patch the values of rx_buf */
817 ret = spi_test_translate(spi, &x->rx_buf, x->len,
818 (void *)tx, rx);
819 if (ret)
820 return ret;
821
822 /* and add it to the list */
823 spi_message_add_tail(x, msg);
824 }
825
826 /* fill in the transfer buffers with pattern */
827 ret = spi_test_fill_pattern(spi, test);
828 if (ret)
829 return ret;
830
831 /* and execute */
832 if (test->execute_msg)
833 ret = test->execute_msg(spi, test, tx, rx);
834 else
835 ret = spi_test_execute_msg(spi, test, tx, rx);
836
837 /* handle result */
838 if (ret == test->expected_return)
839 return 0;
840
841 dev_err(&spi->dev,
842 "test failed - test returned %i, but we expect %i\n",
843 ret, test->expected_return);
844
845 if (ret)
846 return ret;
847
848 /* if it is 0, as we expected something else,
849 * then return something special
850 */
851 return -EFAULT;
852}
853
854static int spi_test_run_iter(struct spi_device *spi,
855 const struct spi_test *testtemplate,
856 void *tx, void *rx,
857 size_t len,
858 size_t tx_off,
859 size_t rx_off
860 )
861{
862 struct spi_test test;
863 int i, tx_count, rx_count;
864
865 /* copy the test template to test */
866 memcpy(&test, testtemplate, sizeof(test));
867
868 /* if iterate_transfer_mask is not set,
869 * then set it to first transfer only
870 */
871 if (!(test.iterate_transfer_mask & (BIT(test.transfer_count) - 1)))
872 test.iterate_transfer_mask = 1;
873
874 /* count number of transfers with tx/rx_buf != NULL */
875 rx_count = tx_count = 0;
876 for (i = 0; i < test.transfer_count; i++) {
877 if (test.transfers[i].tx_buf)
878 tx_count++;
879 if (test.transfers[i].rx_buf)
880 rx_count++;
881 }
882
883 /* in some iteration cases warn and exit early,
884 * as there is nothing to do, that has not been tested already...
885 */
886 if (tx_off && (!tx_count)) {
887 dev_warn_once(&spi->dev,
888 "%s: iterate_tx_off configured with tx_buf==NULL - ignoring\n",
889 test.description);
890 return 0;
891 }
892 if (rx_off && (!rx_count)) {
893 dev_warn_once(&spi->dev,
894 "%s: iterate_rx_off configured with rx_buf==NULL - ignoring\n",
895 test.description);
896 return 0;
897 }
898
899 /* write out info */
900 if (!(len || tx_off || rx_off)) {
901 dev_info(&spi->dev, "Running test %s\n", test.description);
902 } else {
903 dev_info(&spi->dev,
904 " with iteration values: len = %zu, tx_off = %zu, rx_off = %zu\n",
905 len, tx_off, rx_off);
906 }
907
908 /* update in the values from iteration values */
909 for (i = 0; i < test.transfer_count; i++) {
910 /* only when bit in transfer mask is set */
911 if (!(test.iterate_transfer_mask & BIT(i)))
912 continue;
913 test.transfers[i].len = len;
914 if (test.transfers[i].tx_buf)
915 test.transfers[i].tx_buf += tx_off;
916 if (test.transfers[i].rx_buf)
917 test.transfers[i].rx_buf += rx_off;
918 }
919
920 /* and execute */
921 return _spi_test_run_iter(spi, &test, tx, rx);
922}
923
924/**
925 * spi_test_execute_msg - default implementation to run a test
926 *
927 * @spi: @spi_device on which to run the @spi_message
928 * @test: the test to execute, which already contains @msg
929 * @tx: the tx buffer allocated for the test sequence
930 * @rx: the rx buffer allocated for the test sequence
931 *
932 * Returns: error code of spi_sync as well as basic error checking
933 */
934int spi_test_execute_msg(struct spi_device *spi, struct spi_test *test,
935 void *tx, void *rx)
936{
937 struct spi_message *msg = &test->msg;
938 int ret = 0;
939 int i;
940
941 /* only if we do not simulate */
942 if (!simulate_only) {
943 ktime_t start;
944
945 /* dump the complete message before and after the transfer */
946 if (dump_messages == 3)
947 spi_test_dump_message(spi, msg, true);
948
949 start = ktime_get();
950 /* run spi message */
951 ret = spi_sync(spi, msg);
952 test->elapsed_time = ktime_to_ns(ktime_sub(ktime_get(), start));
953 if (ret == -ETIMEDOUT) {
954 dev_info(&spi->dev,
955 "spi-message timed out - rerunning...\n");
956 /* rerun after a few explicit schedules */
957 for (i = 0; i < 16; i++)
958 schedule();
959 ret = spi_sync(spi, msg);
960 }
961 if (ret) {
962 dev_err(&spi->dev,
963 "Failed to execute spi_message: %i\n",
964 ret);
965 goto exit;
966 }
967
968 /* do some extra error checks */
969 if (msg->frame_length != msg->actual_length) {
970 dev_err(&spi->dev,
971 "actual length differs from expected\n");
972 ret = -EIO;
973 goto exit;
974 }
975
976 /* run rx-buffer tests */
977 ret = spi_test_check_loopback_result(spi, msg, tx, rx);
978 if (ret)
979 goto exit;
980
981 ret = spi_test_check_elapsed_time(spi, test);
982 }
983
984 /* if requested or on error dump message (including data) */
985exit:
986 if (dump_messages || ret)
987 spi_test_dump_message(spi, msg,
988 (dump_messages >= 2) || (ret));
989
990 return ret;
991}
992EXPORT_SYMBOL_GPL(spi_test_execute_msg);
993
994/**
995 * spi_test_run_test - run an individual spi_test
996 * including all the relevant iterations on:
997 * length and buffer alignment
998 *
999 * @spi: the spi_device to send the messages to
1000 * @test: the test which we need to execute
1001 * @tx: the tx buffer allocated for the test sequence
1002 * @rx: the rx buffer allocated for the test sequence
1003 *
1004 * Returns: status code of spi_sync or other failures
1005 */
1006
1007int spi_test_run_test(struct spi_device *spi, const struct spi_test *test,
1008 void *tx, void *rx)
1009{
1010 int idx_len;
1011 size_t len;
1012 size_t tx_align, rx_align;
1013 int ret;
1014
1015 /* test for transfer limits */
1016 if (test->transfer_count >= SPI_TEST_MAX_TRANSFERS) {
1017 dev_err(&spi->dev,
1018 "%s: Exceeded max number of transfers with %i\n",
1019 test->description, test->transfer_count);
1020 return -E2BIG;
1021 }
1022
1023 /* setting up some values in spi_message
1024 * based on some settings in spi_master
1025 * some of this can also get done in the run() method
1026 */
1027
1028 /* iterate over all the iterable values using macros
1029 * (to make it a bit more readable...
1030 */
1031#define FOR_EACH_ALIGNMENT(var) \
1032 for (var = 0; \
1033 var < (test->iterate_##var ? \
1034 (spi->master->dma_alignment ? \
1035 spi->master->dma_alignment : \
1036 test->iterate_##var) : \
1037 1); \
1038 var++)
1039
1040 for (idx_len = 0; idx_len < SPI_TEST_MAX_ITERATE &&
1041 (len = test->iterate_len[idx_len]) != -1; idx_len++) {
1042 if ((run_only_iter_len > -1) && len != run_only_iter_len)
1043 continue;
1044 FOR_EACH_ALIGNMENT(tx_align) {
1045 FOR_EACH_ALIGNMENT(rx_align) {
1046 /* and run the iteration */
1047 ret = spi_test_run_iter(spi, test,
1048 tx, rx,
1049 len,
1050 tx_align,
1051 rx_align);
1052 if (ret)
1053 return ret;
1054 }
1055 }
1056 }
1057
1058 return 0;
1059}
1060EXPORT_SYMBOL_GPL(spi_test_run_test);
1061
1062/**
1063 * spi_test_run_tests - run an array of spi_messages tests
1064 * @spi: the spi device on which to run the tests
1065 * @tests: NULL-terminated array of @spi_test
1066 *
1067 * Returns: status errors as per @spi_test_run_test()
1068 */
1069
1070int spi_test_run_tests(struct spi_device *spi,
1071 struct spi_test *tests)
1072{
1073 char *rx = NULL, *tx = NULL;
1074 int ret = 0, count = 0;
1075 struct spi_test *test;
1076
1077 /* allocate rx/tx buffers of 128kB size without devm
1078 * in the hope that is on a page boundary
1079 */
1080 if (use_vmalloc)
1081 rx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
1082 else
1083 rx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
1084 if (!rx)
1085 return -ENOMEM;
1086
1087
1088 if (use_vmalloc)
1089 tx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
1090 else
1091 tx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
1092 if (!tx) {
1093 ret = -ENOMEM;
1094 goto err_tx;
1095 }
1096
1097 /* now run the individual tests in the table */
1098 for (test = tests, count = 0; test->description[0];
1099 test++, count++) {
1100 /* only run test if requested */
1101 if ((run_only_test > -1) && (count != run_only_test))
1102 continue;
1103 /* run custom implementation */
1104 if (test->run_test)
1105 ret = test->run_test(spi, test, tx, rx);
1106 else
1107 ret = spi_test_run_test(spi, test, tx, rx);
1108 if (ret)
1109 goto out;
1110 /* add some delays so that we can easily
1111 * detect the individual tests when using a logic analyzer
1112 * we also add scheduling to avoid potential spi_timeouts...
1113 */
1114 if (delay_ms)
1115 mdelay(delay_ms);
1116 schedule();
1117 }
1118
1119out:
1120 kvfree(tx);
1121err_tx:
1122 kvfree(rx);
1123 return ret;
1124}
1125EXPORT_SYMBOL_GPL(spi_test_run_tests);
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * linux/drivers/spi/spi-loopback-test.c
4 *
5 * (c) Martin Sperl <kernel@martin.sperl.org>
6 *
7 * Loopback test driver to test several typical spi_message conditions
8 * that a spi_master driver may encounter
9 * this can also get used for regression testing
10 */
11
12#include <linux/delay.h>
13#include <linux/kernel.h>
14#include <linux/ktime.h>
15#include <linux/list.h>
16#include <linux/list_sort.h>
17#include <linux/module.h>
18#include <linux/of_device.h>
19#include <linux/printk.h>
20#include <linux/vmalloc.h>
21#include <linux/spi/spi.h>
22
23#include "spi-test.h"
24
25/* flag to only simulate transfers */
26static int simulate_only;
27module_param(simulate_only, int, 0);
28MODULE_PARM_DESC(simulate_only, "if not 0 do not execute the spi message");
29
30/* dump spi messages */
31static int dump_messages;
32module_param(dump_messages, int, 0);
33MODULE_PARM_DESC(dump_messages,
34 "=1 dump the basic spi_message_structure, " \
35 "=2 dump the spi_message_structure including data, " \
36 "=3 dump the spi_message structure before and after execution");
37/* the device is jumpered for loopback - enabling some rx_buf tests */
38static int loopback;
39module_param(loopback, int, 0);
40MODULE_PARM_DESC(loopback,
41 "if set enable loopback mode, where the rx_buf " \
42 "is checked to match tx_buf after the spi_message " \
43 "is executed");
44
45static int loop_req;
46module_param(loop_req, int, 0);
47MODULE_PARM_DESC(loop_req,
48 "if set controller will be asked to enable test loop mode. " \
49 "If controller supported it, MISO and MOSI will be connected");
50
51static int no_cs;
52module_param(no_cs, int, 0);
53MODULE_PARM_DESC(no_cs,
54 "if set Chip Select (CS) will not be used");
55
56/* run only a specific test */
57static int run_only_test = -1;
58module_param(run_only_test, int, 0);
59MODULE_PARM_DESC(run_only_test,
60 "only run the test with this number (0-based !)");
61
62/* use vmalloc'ed buffers */
63static int use_vmalloc;
64module_param(use_vmalloc, int, 0644);
65MODULE_PARM_DESC(use_vmalloc,
66 "use vmalloc'ed buffers instead of kmalloc'ed");
67
68/* check rx ranges */
69static int check_ranges = 1;
70module_param(check_ranges, int, 0644);
71MODULE_PARM_DESC(check_ranges,
72 "checks rx_buffer pattern are valid");
73
74/* the actual tests to execute */
75static struct spi_test spi_tests[] = {
76 {
77 .description = "tx/rx-transfer - start of page",
78 .fill_option = FILL_COUNT_8,
79 .iterate_len = { ITERATE_MAX_LEN },
80 .iterate_tx_align = ITERATE_ALIGN,
81 .iterate_rx_align = ITERATE_ALIGN,
82 .transfer_count = 1,
83 .transfers = {
84 {
85 .tx_buf = TX(0),
86 .rx_buf = RX(0),
87 },
88 },
89 },
90 {
91 .description = "tx/rx-transfer - crossing PAGE_SIZE",
92 .fill_option = FILL_COUNT_8,
93 .iterate_len = { ITERATE_LEN },
94 .iterate_tx_align = ITERATE_ALIGN,
95 .iterate_rx_align = ITERATE_ALIGN,
96 .transfer_count = 1,
97 .transfers = {
98 {
99 .tx_buf = TX(PAGE_SIZE - 4),
100 .rx_buf = RX(PAGE_SIZE - 4),
101 },
102 },
103 },
104 {
105 .description = "tx-transfer - only",
106 .fill_option = FILL_COUNT_8,
107 .iterate_len = { ITERATE_MAX_LEN },
108 .iterate_tx_align = ITERATE_ALIGN,
109 .transfer_count = 1,
110 .transfers = {
111 {
112 .tx_buf = TX(0),
113 },
114 },
115 },
116 {
117 .description = "rx-transfer - only",
118 .fill_option = FILL_COUNT_8,
119 .iterate_len = { ITERATE_MAX_LEN },
120 .iterate_rx_align = ITERATE_ALIGN,
121 .transfer_count = 1,
122 .transfers = {
123 {
124 .rx_buf = RX(0),
125 },
126 },
127 },
128 {
129 .description = "two tx-transfers - alter both",
130 .fill_option = FILL_COUNT_8,
131 .iterate_len = { ITERATE_LEN },
132 .iterate_tx_align = ITERATE_ALIGN,
133 .iterate_transfer_mask = BIT(0) | BIT(1),
134 .transfer_count = 2,
135 .transfers = {
136 {
137 .tx_buf = TX(0),
138 },
139 {
140 /* this is why we cant use ITERATE_MAX_LEN */
141 .tx_buf = TX(SPI_TEST_MAX_SIZE_HALF),
142 },
143 },
144 },
145 {
146 .description = "two tx-transfers - alter first",
147 .fill_option = FILL_COUNT_8,
148 .iterate_len = { ITERATE_MAX_LEN },
149 .iterate_tx_align = ITERATE_ALIGN,
150 .iterate_transfer_mask = BIT(0),
151 .transfer_count = 2,
152 .transfers = {
153 {
154 .tx_buf = TX(64),
155 },
156 {
157 .len = 1,
158 .tx_buf = TX(0),
159 },
160 },
161 },
162 {
163 .description = "two tx-transfers - alter second",
164 .fill_option = FILL_COUNT_8,
165 .iterate_len = { ITERATE_MAX_LEN },
166 .iterate_tx_align = ITERATE_ALIGN,
167 .iterate_transfer_mask = BIT(1),
168 .transfer_count = 2,
169 .transfers = {
170 {
171 .len = 16,
172 .tx_buf = TX(0),
173 },
174 {
175 .tx_buf = TX(64),
176 },
177 },
178 },
179 {
180 .description = "two transfers tx then rx - alter both",
181 .fill_option = FILL_COUNT_8,
182 .iterate_len = { ITERATE_MAX_LEN },
183 .iterate_tx_align = ITERATE_ALIGN,
184 .iterate_transfer_mask = BIT(0) | BIT(1),
185 .transfer_count = 2,
186 .transfers = {
187 {
188 .tx_buf = TX(0),
189 },
190 {
191 .rx_buf = RX(0),
192 },
193 },
194 },
195 {
196 .description = "two transfers tx then rx - alter tx",
197 .fill_option = FILL_COUNT_8,
198 .iterate_len = { ITERATE_MAX_LEN },
199 .iterate_tx_align = ITERATE_ALIGN,
200 .iterate_transfer_mask = BIT(0),
201 .transfer_count = 2,
202 .transfers = {
203 {
204 .tx_buf = TX(0),
205 },
206 {
207 .len = 1,
208 .rx_buf = RX(0),
209 },
210 },
211 },
212 {
213 .description = "two transfers tx then rx - alter rx",
214 .fill_option = FILL_COUNT_8,
215 .iterate_len = { ITERATE_MAX_LEN },
216 .iterate_tx_align = ITERATE_ALIGN,
217 .iterate_transfer_mask = BIT(1),
218 .transfer_count = 2,
219 .transfers = {
220 {
221 .len = 1,
222 .tx_buf = TX(0),
223 },
224 {
225 .rx_buf = RX(0),
226 },
227 },
228 },
229 {
230 .description = "two tx+rx transfers - alter both",
231 .fill_option = FILL_COUNT_8,
232 .iterate_len = { ITERATE_LEN },
233 .iterate_tx_align = ITERATE_ALIGN,
234 .iterate_transfer_mask = BIT(0) | BIT(1),
235 .transfer_count = 2,
236 .transfers = {
237 {
238 .tx_buf = TX(0),
239 .rx_buf = RX(0),
240 },
241 {
242 /* making sure we align without overwrite
243 * the reason we can not use ITERATE_MAX_LEN
244 */
245 .tx_buf = TX(SPI_TEST_MAX_SIZE_HALF),
246 .rx_buf = RX(SPI_TEST_MAX_SIZE_HALF),
247 },
248 },
249 },
250 {
251 .description = "two tx+rx transfers - alter first",
252 .fill_option = FILL_COUNT_8,
253 .iterate_len = { ITERATE_MAX_LEN },
254 .iterate_tx_align = ITERATE_ALIGN,
255 .iterate_transfer_mask = BIT(0),
256 .transfer_count = 2,
257 .transfers = {
258 {
259 /* making sure we align without overwrite */
260 .tx_buf = TX(1024),
261 .rx_buf = RX(1024),
262 },
263 {
264 .len = 1,
265 /* making sure we align without overwrite */
266 .tx_buf = TX(0),
267 .rx_buf = RX(0),
268 },
269 },
270 },
271 {
272 .description = "two tx+rx transfers - alter second",
273 .fill_option = FILL_COUNT_8,
274 .iterate_len = { ITERATE_MAX_LEN },
275 .iterate_tx_align = ITERATE_ALIGN,
276 .iterate_transfer_mask = BIT(1),
277 .transfer_count = 2,
278 .transfers = {
279 {
280 .len = 1,
281 .tx_buf = TX(0),
282 .rx_buf = RX(0),
283 },
284 {
285 /* making sure we align without overwrite */
286 .tx_buf = TX(1024),
287 .rx_buf = RX(1024),
288 },
289 },
290 },
291 {
292 .description = "two tx+rx transfers - delay after transfer",
293 .fill_option = FILL_COUNT_8,
294 .iterate_len = { ITERATE_MAX_LEN },
295 .iterate_transfer_mask = BIT(0) | BIT(1),
296 .transfer_count = 2,
297 .transfers = {
298 {
299 .tx_buf = TX(0),
300 .rx_buf = RX(0),
301 .delay = {
302 .value = 1000,
303 .unit = SPI_DELAY_UNIT_USECS,
304 },
305 },
306 {
307 .tx_buf = TX(0),
308 .rx_buf = RX(0),
309 .delay = {
310 .value = 1000,
311 .unit = SPI_DELAY_UNIT_USECS,
312 },
313 },
314 },
315 },
316
317 { /* end of tests sequence */ }
318};
319
320static int spi_loopback_test_probe(struct spi_device *spi)
321{
322 int ret;
323
324 if (loop_req || no_cs) {
325 spi->mode |= loop_req ? SPI_LOOP : 0;
326 spi->mode |= no_cs ? SPI_NO_CS : 0;
327 ret = spi_setup(spi);
328 if (ret) {
329 dev_err(&spi->dev, "SPI setup with SPI_LOOP or SPI_NO_CS failed (%d)\n",
330 ret);
331 return ret;
332 }
333 }
334
335 dev_info(&spi->dev, "Executing spi-loopback-tests\n");
336
337 ret = spi_test_run_tests(spi, spi_tests);
338
339 dev_info(&spi->dev, "Finished spi-loopback-tests with return: %i\n",
340 ret);
341
342 return ret;
343}
344
345/* non const match table to permit to change via a module parameter */
346static struct of_device_id spi_loopback_test_of_match[] = {
347 { .compatible = "linux,spi-loopback-test", },
348 { }
349};
350
351/* allow to override the compatible string via a module_parameter */
352module_param_string(compatible, spi_loopback_test_of_match[0].compatible,
353 sizeof(spi_loopback_test_of_match[0].compatible),
354 0000);
355
356MODULE_DEVICE_TABLE(of, spi_loopback_test_of_match);
357
358static struct spi_driver spi_loopback_test_driver = {
359 .driver = {
360 .name = "spi-loopback-test",
361 .owner = THIS_MODULE,
362 .of_match_table = spi_loopback_test_of_match,
363 },
364 .probe = spi_loopback_test_probe,
365};
366
367module_spi_driver(spi_loopback_test_driver);
368
369MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>");
370MODULE_DESCRIPTION("test spi_driver to check core functionality");
371MODULE_LICENSE("GPL");
372
373/*-------------------------------------------------------------------------*/
374
375/* spi_test implementation */
376
377#define RANGE_CHECK(ptr, plen, start, slen) \
378 ((ptr >= start) && (ptr + plen <= start + slen))
379
380/* we allocate one page more, to allow for offsets */
381#define SPI_TEST_MAX_SIZE_PLUS (SPI_TEST_MAX_SIZE + PAGE_SIZE)
382
383static void spi_test_print_hex_dump(char *pre, const void *ptr, size_t len)
384{
385 /* limit the hex_dump */
386 if (len < 1024) {
387 print_hex_dump(KERN_INFO, pre,
388 DUMP_PREFIX_OFFSET, 16, 1,
389 ptr, len, 0);
390 return;
391 }
392 /* print head */
393 print_hex_dump(KERN_INFO, pre,
394 DUMP_PREFIX_OFFSET, 16, 1,
395 ptr, 512, 0);
396 /* print tail */
397 pr_info("%s truncated - continuing at offset %04zx\n",
398 pre, len - 512);
399 print_hex_dump(KERN_INFO, pre,
400 DUMP_PREFIX_OFFSET, 16, 1,
401 ptr + (len - 512), 512, 0);
402}
403
404static void spi_test_dump_message(struct spi_device *spi,
405 struct spi_message *msg,
406 bool dump_data)
407{
408 struct spi_transfer *xfer;
409 int i;
410 u8 b;
411
412 dev_info(&spi->dev, " spi_msg@%pK\n", msg);
413 if (msg->status)
414 dev_info(&spi->dev, " status: %i\n",
415 msg->status);
416 dev_info(&spi->dev, " frame_length: %i\n",
417 msg->frame_length);
418 dev_info(&spi->dev, " actual_length: %i\n",
419 msg->actual_length);
420
421 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
422 dev_info(&spi->dev, " spi_transfer@%pK\n", xfer);
423 dev_info(&spi->dev, " len: %i\n", xfer->len);
424 dev_info(&spi->dev, " tx_buf: %pK\n", xfer->tx_buf);
425 if (dump_data && xfer->tx_buf)
426 spi_test_print_hex_dump(" TX: ",
427 xfer->tx_buf,
428 xfer->len);
429
430 dev_info(&spi->dev, " rx_buf: %pK\n", xfer->rx_buf);
431 if (dump_data && xfer->rx_buf)
432 spi_test_print_hex_dump(" RX: ",
433 xfer->rx_buf,
434 xfer->len);
435 /* check for unwritten test pattern on rx_buf */
436 if (xfer->rx_buf) {
437 for (i = 0 ; i < xfer->len ; i++) {
438 b = ((u8 *)xfer->rx_buf)[xfer->len - 1 - i];
439 if (b != SPI_TEST_PATTERN_UNWRITTEN)
440 break;
441 }
442 if (i)
443 dev_info(&spi->dev,
444 " rx_buf filled with %02x starts at offset: %i\n",
445 SPI_TEST_PATTERN_UNWRITTEN,
446 xfer->len - i);
447 }
448 }
449}
450
451struct rx_ranges {
452 struct list_head list;
453 u8 *start;
454 u8 *end;
455};
456
457static int rx_ranges_cmp(void *priv, const struct list_head *a,
458 const struct list_head *b)
459{
460 struct rx_ranges *rx_a = list_entry(a, struct rx_ranges, list);
461 struct rx_ranges *rx_b = list_entry(b, struct rx_ranges, list);
462
463 if (rx_a->start > rx_b->start)
464 return 1;
465 if (rx_a->start < rx_b->start)
466 return -1;
467 return 0;
468}
469
470static int spi_check_rx_ranges(struct spi_device *spi,
471 struct spi_message *msg,
472 void *rx)
473{
474 struct spi_transfer *xfer;
475 struct rx_ranges ranges[SPI_TEST_MAX_TRANSFERS], *r;
476 int i = 0;
477 LIST_HEAD(ranges_list);
478 u8 *addr;
479 int ret = 0;
480
481 /* loop over all transfers to fill in the rx_ranges */
482 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
483 /* if there is no rx, then no check is needed */
484 if (!xfer->rx_buf)
485 continue;
486 /* fill in the rx_range */
487 if (RANGE_CHECK(xfer->rx_buf, xfer->len,
488 rx, SPI_TEST_MAX_SIZE_PLUS)) {
489 ranges[i].start = xfer->rx_buf;
490 ranges[i].end = xfer->rx_buf + xfer->len;
491 list_add(&ranges[i].list, &ranges_list);
492 i++;
493 }
494 }
495
496 /* if no ranges, then we can return and avoid the checks...*/
497 if (!i)
498 return 0;
499
500 /* sort the list */
501 list_sort(NULL, &ranges_list, rx_ranges_cmp);
502
503 /* and iterate over all the rx addresses */
504 for (addr = rx; addr < (u8 *)rx + SPI_TEST_MAX_SIZE_PLUS; addr++) {
505 /* if we are the DO not write pattern,
506 * then continue with the loop...
507 */
508 if (*addr == SPI_TEST_PATTERN_DO_NOT_WRITE)
509 continue;
510
511 /* check if we are inside a range */
512 list_for_each_entry(r, &ranges_list, list) {
513 /* if so then set to end... */
514 if ((addr >= r->start) && (addr < r->end))
515 addr = r->end;
516 }
517 /* second test after a (hopefull) translation */
518 if (*addr == SPI_TEST_PATTERN_DO_NOT_WRITE)
519 continue;
520
521 /* if still not found then something has modified too much */
522 /* we could list the "closest" transfer here... */
523 dev_err(&spi->dev,
524 "loopback strangeness - rx changed outside of allowed range at: %pK\n",
525 addr);
526 /* do not return, only set ret,
527 * so that we list all addresses
528 */
529 ret = -ERANGE;
530 }
531
532 return ret;
533}
534
535static int spi_test_check_elapsed_time(struct spi_device *spi,
536 struct spi_test *test)
537{
538 int i;
539 unsigned long long estimated_time = 0;
540 unsigned long long delay_usecs = 0;
541
542 for (i = 0; i < test->transfer_count; i++) {
543 struct spi_transfer *xfer = test->transfers + i;
544 unsigned long long nbits = (unsigned long long)BITS_PER_BYTE *
545 xfer->len;
546
547 delay_usecs += xfer->delay.value;
548 if (!xfer->speed_hz)
549 continue;
550 estimated_time += div_u64(nbits * NSEC_PER_SEC, xfer->speed_hz);
551 }
552
553 estimated_time += delay_usecs * NSEC_PER_USEC;
554 if (test->elapsed_time < estimated_time) {
555 dev_err(&spi->dev,
556 "elapsed time %lld ns is shorter than minimum estimated time %lld ns\n",
557 test->elapsed_time, estimated_time);
558
559 return -EINVAL;
560 }
561
562 return 0;
563}
564
565static int spi_test_check_loopback_result(struct spi_device *spi,
566 struct spi_message *msg,
567 void *tx, void *rx)
568{
569 struct spi_transfer *xfer;
570 u8 rxb, txb;
571 size_t i;
572 int ret;
573
574 /* checks rx_buffer pattern are valid with loopback or without */
575 if (check_ranges) {
576 ret = spi_check_rx_ranges(spi, msg, rx);
577 if (ret)
578 return ret;
579 }
580
581 /* if we run without loopback, then return now */
582 if (!loopback)
583 return 0;
584
585 /* if applicable to transfer check that rx_buf is equal to tx_buf */
586 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
587 /* if there is no rx, then no check is needed */
588 if (!xfer->len || !xfer->rx_buf)
589 continue;
590 /* so depending on tx_buf we need to handle things */
591 if (xfer->tx_buf) {
592 for (i = 0; i < xfer->len; i++) {
593 txb = ((u8 *)xfer->tx_buf)[i];
594 rxb = ((u8 *)xfer->rx_buf)[i];
595 if (txb != rxb)
596 goto mismatch_error;
597 }
598 } else {
599 /* first byte received */
600 txb = ((u8 *)xfer->rx_buf)[0];
601 /* first byte may be 0 or xff */
602 if (!((txb == 0) || (txb == 0xff))) {
603 dev_err(&spi->dev,
604 "loopback strangeness - we expect 0x00 or 0xff, but not 0x%02x\n",
605 txb);
606 return -EINVAL;
607 }
608 /* check that all bytes are identical */
609 for (i = 1; i < xfer->len; i++) {
610 rxb = ((u8 *)xfer->rx_buf)[i];
611 if (rxb != txb)
612 goto mismatch_error;
613 }
614 }
615 }
616
617 return 0;
618
619mismatch_error:
620 dev_err(&spi->dev,
621 "loopback strangeness - transfer mismatch on byte %04zx - expected 0x%02x, but got 0x%02x\n",
622 i, txb, rxb);
623
624 return -EINVAL;
625}
626
627static int spi_test_translate(struct spi_device *spi,
628 void **ptr, size_t len,
629 void *tx, void *rx)
630{
631 size_t off;
632
633 /* return on null */
634 if (!*ptr)
635 return 0;
636
637 /* in the MAX_SIZE_HALF case modify the pointer */
638 if (((size_t)*ptr) & SPI_TEST_MAX_SIZE_HALF)
639 /* move the pointer to the correct range */
640 *ptr += (SPI_TEST_MAX_SIZE_PLUS / 2) -
641 SPI_TEST_MAX_SIZE_HALF;
642
643 /* RX range
644 * - we check against MAX_SIZE_PLUS to allow for automated alignment
645 */
646 if (RANGE_CHECK(*ptr, len, RX(0), SPI_TEST_MAX_SIZE_PLUS)) {
647 off = *ptr - RX(0);
648 *ptr = rx + off;
649
650 return 0;
651 }
652
653 /* TX range */
654 if (RANGE_CHECK(*ptr, len, TX(0), SPI_TEST_MAX_SIZE_PLUS)) {
655 off = *ptr - TX(0);
656 *ptr = tx + off;
657
658 return 0;
659 }
660
661 dev_err(&spi->dev,
662 "PointerRange [%pK:%pK[ not in range [%pK:%pK[ or [%pK:%pK[\n",
663 *ptr, *ptr + len,
664 RX(0), RX(SPI_TEST_MAX_SIZE),
665 TX(0), TX(SPI_TEST_MAX_SIZE));
666
667 return -EINVAL;
668}
669
670static int spi_test_fill_pattern(struct spi_device *spi,
671 struct spi_test *test)
672{
673 struct spi_transfer *xfers = test->transfers;
674 u8 *tx_buf;
675 size_t count = 0;
676 int i, j;
677
678#ifdef __BIG_ENDIAN
679#define GET_VALUE_BYTE(value, index, bytes) \
680 (value >> (8 * (bytes - 1 - count % bytes)))
681#else
682#define GET_VALUE_BYTE(value, index, bytes) \
683 (value >> (8 * (count % bytes)))
684#endif
685
686 /* fill all transfers with the pattern requested */
687 for (i = 0; i < test->transfer_count; i++) {
688 /* fill rx_buf with SPI_TEST_PATTERN_UNWRITTEN */
689 if (xfers[i].rx_buf)
690 memset(xfers[i].rx_buf, SPI_TEST_PATTERN_UNWRITTEN,
691 xfers[i].len);
692 /* if tx_buf is NULL then skip */
693 tx_buf = (u8 *)xfers[i].tx_buf;
694 if (!tx_buf)
695 continue;
696 /* modify all the transfers */
697 for (j = 0; j < xfers[i].len; j++, tx_buf++, count++) {
698 /* fill tx */
699 switch (test->fill_option) {
700 case FILL_MEMSET_8:
701 *tx_buf = test->fill_pattern;
702 break;
703 case FILL_MEMSET_16:
704 *tx_buf = GET_VALUE_BYTE(test->fill_pattern,
705 count, 2);
706 break;
707 case FILL_MEMSET_24:
708 *tx_buf = GET_VALUE_BYTE(test->fill_pattern,
709 count, 3);
710 break;
711 case FILL_MEMSET_32:
712 *tx_buf = GET_VALUE_BYTE(test->fill_pattern,
713 count, 4);
714 break;
715 case FILL_COUNT_8:
716 *tx_buf = count;
717 break;
718 case FILL_COUNT_16:
719 *tx_buf = GET_VALUE_BYTE(count, count, 2);
720 break;
721 case FILL_COUNT_24:
722 *tx_buf = GET_VALUE_BYTE(count, count, 3);
723 break;
724 case FILL_COUNT_32:
725 *tx_buf = GET_VALUE_BYTE(count, count, 4);
726 break;
727 case FILL_TRANSFER_BYTE_8:
728 *tx_buf = j;
729 break;
730 case FILL_TRANSFER_BYTE_16:
731 *tx_buf = GET_VALUE_BYTE(j, j, 2);
732 break;
733 case FILL_TRANSFER_BYTE_24:
734 *tx_buf = GET_VALUE_BYTE(j, j, 3);
735 break;
736 case FILL_TRANSFER_BYTE_32:
737 *tx_buf = GET_VALUE_BYTE(j, j, 4);
738 break;
739 case FILL_TRANSFER_NUM:
740 *tx_buf = i;
741 break;
742 default:
743 dev_err(&spi->dev,
744 "unsupported fill_option: %i\n",
745 test->fill_option);
746 return -EINVAL;
747 }
748 }
749 }
750
751 return 0;
752}
753
754static int _spi_test_run_iter(struct spi_device *spi,
755 struct spi_test *test,
756 void *tx, void *rx)
757{
758 struct spi_message *msg = &test->msg;
759 struct spi_transfer *x;
760 int i, ret;
761
762 /* initialize message - zero-filled via static initialization */
763 spi_message_init_no_memset(msg);
764
765 /* fill rx with the DO_NOT_WRITE pattern */
766 memset(rx, SPI_TEST_PATTERN_DO_NOT_WRITE, SPI_TEST_MAX_SIZE_PLUS);
767
768 /* add the individual transfers */
769 for (i = 0; i < test->transfer_count; i++) {
770 x = &test->transfers[i];
771
772 /* patch the values of tx_buf */
773 ret = spi_test_translate(spi, (void **)&x->tx_buf, x->len,
774 (void *)tx, rx);
775 if (ret)
776 return ret;
777
778 /* patch the values of rx_buf */
779 ret = spi_test_translate(spi, &x->rx_buf, x->len,
780 (void *)tx, rx);
781 if (ret)
782 return ret;
783
784 /* and add it to the list */
785 spi_message_add_tail(x, msg);
786 }
787
788 /* fill in the transfer buffers with pattern */
789 ret = spi_test_fill_pattern(spi, test);
790 if (ret)
791 return ret;
792
793 /* and execute */
794 if (test->execute_msg)
795 ret = test->execute_msg(spi, test, tx, rx);
796 else
797 ret = spi_test_execute_msg(spi, test, tx, rx);
798
799 /* handle result */
800 if (ret == test->expected_return)
801 return 0;
802
803 dev_err(&spi->dev,
804 "test failed - test returned %i, but we expect %i\n",
805 ret, test->expected_return);
806
807 if (ret)
808 return ret;
809
810 /* if it is 0, as we expected something else,
811 * then return something special
812 */
813 return -EFAULT;
814}
815
816static int spi_test_run_iter(struct spi_device *spi,
817 const struct spi_test *testtemplate,
818 void *tx, void *rx,
819 size_t len,
820 size_t tx_off,
821 size_t rx_off
822 )
823{
824 struct spi_test test;
825 int i, tx_count, rx_count;
826
827 /* copy the test template to test */
828 memcpy(&test, testtemplate, sizeof(test));
829
830 /* if iterate_transfer_mask is not set,
831 * then set it to first transfer only
832 */
833 if (!(test.iterate_transfer_mask & (BIT(test.transfer_count) - 1)))
834 test.iterate_transfer_mask = 1;
835
836 /* count number of transfers with tx/rx_buf != NULL */
837 rx_count = tx_count = 0;
838 for (i = 0; i < test.transfer_count; i++) {
839 if (test.transfers[i].tx_buf)
840 tx_count++;
841 if (test.transfers[i].rx_buf)
842 rx_count++;
843 }
844
845 /* in some iteration cases warn and exit early,
846 * as there is nothing to do, that has not been tested already...
847 */
848 if (tx_off && (!tx_count)) {
849 dev_warn_once(&spi->dev,
850 "%s: iterate_tx_off configured with tx_buf==NULL - ignoring\n",
851 test.description);
852 return 0;
853 }
854 if (rx_off && (!rx_count)) {
855 dev_warn_once(&spi->dev,
856 "%s: iterate_rx_off configured with rx_buf==NULL - ignoring\n",
857 test.description);
858 return 0;
859 }
860
861 /* write out info */
862 if (!(len || tx_off || rx_off)) {
863 dev_info(&spi->dev, "Running test %s\n", test.description);
864 } else {
865 dev_info(&spi->dev,
866 " with iteration values: len = %zu, tx_off = %zu, rx_off = %zu\n",
867 len, tx_off, rx_off);
868 }
869
870 /* update in the values from iteration values */
871 for (i = 0; i < test.transfer_count; i++) {
872 /* only when bit in transfer mask is set */
873 if (!(test.iterate_transfer_mask & BIT(i)))
874 continue;
875 test.transfers[i].len = len;
876 if (test.transfers[i].tx_buf)
877 test.transfers[i].tx_buf += tx_off;
878 if (test.transfers[i].rx_buf)
879 test.transfers[i].rx_buf += rx_off;
880 }
881
882 /* and execute */
883 return _spi_test_run_iter(spi, &test, tx, rx);
884}
885
886/**
887 * spi_test_execute_msg - default implementation to run a test
888 *
889 * @spi: @spi_device on which to run the @spi_message
890 * @test: the test to execute, which already contains @msg
891 * @tx: the tx buffer allocated for the test sequence
892 * @rx: the rx buffer allocated for the test sequence
893 *
894 * Returns: error code of spi_sync as well as basic error checking
895 */
896int spi_test_execute_msg(struct spi_device *spi, struct spi_test *test,
897 void *tx, void *rx)
898{
899 struct spi_message *msg = &test->msg;
900 int ret = 0;
901 int i;
902
903 /* only if we do not simulate */
904 if (!simulate_only) {
905 ktime_t start;
906
907 /* dump the complete message before and after the transfer */
908 if (dump_messages == 3)
909 spi_test_dump_message(spi, msg, true);
910
911 start = ktime_get();
912 /* run spi message */
913 ret = spi_sync(spi, msg);
914 test->elapsed_time = ktime_to_ns(ktime_sub(ktime_get(), start));
915 if (ret == -ETIMEDOUT) {
916 dev_info(&spi->dev,
917 "spi-message timed out - rerunning...\n");
918 /* rerun after a few explicit schedules */
919 for (i = 0; i < 16; i++)
920 schedule();
921 ret = spi_sync(spi, msg);
922 }
923 if (ret) {
924 dev_err(&spi->dev,
925 "Failed to execute spi_message: %i\n",
926 ret);
927 goto exit;
928 }
929
930 /* do some extra error checks */
931 if (msg->frame_length != msg->actual_length) {
932 dev_err(&spi->dev,
933 "actual length differs from expected\n");
934 ret = -EIO;
935 goto exit;
936 }
937
938 /* run rx-buffer tests */
939 ret = spi_test_check_loopback_result(spi, msg, tx, rx);
940 if (ret)
941 goto exit;
942
943 ret = spi_test_check_elapsed_time(spi, test);
944 }
945
946 /* if requested or on error dump message (including data) */
947exit:
948 if (dump_messages || ret)
949 spi_test_dump_message(spi, msg,
950 (dump_messages >= 2) || (ret));
951
952 return ret;
953}
954EXPORT_SYMBOL_GPL(spi_test_execute_msg);
955
956/**
957 * spi_test_run_test - run an individual spi_test
958 * including all the relevant iterations on:
959 * length and buffer alignment
960 *
961 * @spi: the spi_device to send the messages to
962 * @test: the test which we need to execute
963 * @tx: the tx buffer allocated for the test sequence
964 * @rx: the rx buffer allocated for the test sequence
965 *
966 * Returns: status code of spi_sync or other failures
967 */
968
969int spi_test_run_test(struct spi_device *spi, const struct spi_test *test,
970 void *tx, void *rx)
971{
972 int idx_len;
973 size_t len;
974 size_t tx_align, rx_align;
975 int ret;
976
977 /* test for transfer limits */
978 if (test->transfer_count >= SPI_TEST_MAX_TRANSFERS) {
979 dev_err(&spi->dev,
980 "%s: Exceeded max number of transfers with %i\n",
981 test->description, test->transfer_count);
982 return -E2BIG;
983 }
984
985 /* setting up some values in spi_message
986 * based on some settings in spi_master
987 * some of this can also get done in the run() method
988 */
989
990 /* iterate over all the iterable values using macros
991 * (to make it a bit more readable...
992 */
993#define FOR_EACH_ALIGNMENT(var) \
994 for (var = 0; \
995 var < (test->iterate_##var ? \
996 (spi->master->dma_alignment ? \
997 spi->master->dma_alignment : \
998 test->iterate_##var) : \
999 1); \
1000 var++)
1001
1002 for (idx_len = 0; idx_len < SPI_TEST_MAX_ITERATE &&
1003 (len = test->iterate_len[idx_len]) != -1; idx_len++) {
1004 FOR_EACH_ALIGNMENT(tx_align) {
1005 FOR_EACH_ALIGNMENT(rx_align) {
1006 /* and run the iteration */
1007 ret = spi_test_run_iter(spi, test,
1008 tx, rx,
1009 len,
1010 tx_align,
1011 rx_align);
1012 if (ret)
1013 return ret;
1014 }
1015 }
1016 }
1017
1018 return 0;
1019}
1020EXPORT_SYMBOL_GPL(spi_test_run_test);
1021
1022/**
1023 * spi_test_run_tests - run an array of spi_messages tests
1024 * @spi: the spi device on which to run the tests
1025 * @tests: NULL-terminated array of @spi_test
1026 *
1027 * Returns: status errors as per @spi_test_run_test()
1028 */
1029
1030int spi_test_run_tests(struct spi_device *spi,
1031 struct spi_test *tests)
1032{
1033 char *rx = NULL, *tx = NULL;
1034 int ret = 0, count = 0;
1035 struct spi_test *test;
1036
1037 /* allocate rx/tx buffers of 128kB size without devm
1038 * in the hope that is on a page boundary
1039 */
1040 if (use_vmalloc)
1041 rx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
1042 else
1043 rx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
1044 if (!rx)
1045 return -ENOMEM;
1046
1047
1048 if (use_vmalloc)
1049 tx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
1050 else
1051 tx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
1052 if (!tx) {
1053 ret = -ENOMEM;
1054 goto err_tx;
1055 }
1056
1057 /* now run the individual tests in the table */
1058 for (test = tests, count = 0; test->description[0];
1059 test++, count++) {
1060 /* only run test if requested */
1061 if ((run_only_test > -1) && (count != run_only_test))
1062 continue;
1063 /* run custom implementation */
1064 if (test->run_test)
1065 ret = test->run_test(spi, test, tx, rx);
1066 else
1067 ret = spi_test_run_test(spi, test, tx, rx);
1068 if (ret)
1069 goto out;
1070 /* add some delays so that we can easily
1071 * detect the individual tests when using a logic analyzer
1072 * we also add scheduling to avoid potential spi_timeouts...
1073 */
1074 mdelay(100);
1075 schedule();
1076 }
1077
1078out:
1079 kvfree(tx);
1080err_tx:
1081 kvfree(rx);
1082 return ret;
1083}
1084EXPORT_SYMBOL_GPL(spi_test_run_tests);