Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Touchscreen driver configuration
4#
5menuconfig INPUT_TOUCHSCREEN
6 bool "Touchscreens"
7 help
8 Say Y here, and a list of supported touchscreens will be displayed.
9 This option doesn't affect the kernel.
10
11 If unsure, say Y.
12
13if INPUT_TOUCHSCREEN
14
15config TOUCHSCREEN_88PM860X
16 tristate "Marvell 88PM860x touchscreen"
17 depends on MFD_88PM860X
18 help
19 Say Y here if you have a 88PM860x PMIC and want to enable
20 support for the built-in touchscreen.
21
22 If unsure, say N.
23
24 To compile this driver as a module, choose M here: the
25 module will be called 88pm860x-ts.
26
27config TOUCHSCREEN_ADS7846
28 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on SPI_MASTER
30 depends on HWMON = n || HWMON
31 help
32 Say Y here if you have a touchscreen interface using the
33 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
34 and your board-specific setup code includes that in its
35 table of SPI devices.
36
37 If HWMON is selected, and the driver is told the reference voltage
38 on your board, you will also get hwmon interfaces for the voltage
39 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40
41 If unsure, say N (but it's safe to say "Y").
42
43 To compile this driver as a module, choose M here: the
44 module will be called ads7846.
45
46config TOUCHSCREEN_AD7877
47 tristate "AD7877 based touchscreens"
48 depends on SPI_MASTER
49 help
50 Say Y here if you have a touchscreen interface using the
51 AD7877 controller, and your board-specific initialization
52 code includes that in its table of SPI devices.
53
54 If unsure, say N (but it's safe to say "Y").
55
56 To compile this driver as a module, choose M here: the
57 module will be called ad7877.
58
59config TOUCHSCREEN_AD7879
60 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 help
62 Say Y here if you want to support a touchscreen interface using
63 the AD7879-1/AD7889-1 controller.
64
65 You should select a bus connection too.
66
67 To compile this driver as a module, choose M here: the
68 module will be called ad7879.
69
70config TOUCHSCREEN_AD7879_I2C
71 tristate "support I2C bus connection"
72 depends on TOUCHSCREEN_AD7879 && I2C
73 select REGMAP_I2C
74 help
75 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
76
77 To compile this driver as a module, choose M here: the
78 module will be called ad7879-i2c.
79
80config TOUCHSCREEN_AD7879_SPI
81 tristate "support SPI bus connection"
82 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
83 select REGMAP_SPI
84 help
85 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
86
87 If unsure, say N (but it's safe to say "Y").
88
89 To compile this driver as a module, choose M here: the
90 module will be called ad7879-spi.
91
92config TOUCHSCREEN_ADC
93 tristate "Generic ADC based resistive touchscreen"
94 depends on IIO
95 select IIO_BUFFER
96 select IIO_BUFFER_CB
97 help
98 Say Y here if you want to use the generic ADC
99 resistive touchscreen driver.
100
101 If unsure, say N (but it's safe to say "Y").
102
103 To compile this driver as a module, choose M here: the
104 module will be called resistive-adc-touch.ko.
105
106config TOUCHSCREEN_AR1021_I2C
107 tristate "Microchip AR1020/1021 i2c touchscreen"
108 depends on I2C && OF
109 help
110 Say Y here if you have the Microchip AR1020 or AR1021 touchscreen
111 controller chip in your system.
112
113 If unsure, say N.
114
115 To compile this driver as a module, choose M here: the
116 module will be called ar1021_i2c.
117
118config TOUCHSCREEN_ATMEL_MXT
119 tristate "Atmel mXT I2C Touchscreen"
120 depends on I2C
121 select FW_LOADER
122 help
123 Say Y here if you have Atmel mXT series I2C touchscreen,
124 such as AT42QT602240/ATMXT224, connected to your system.
125
126 If unsure, say N.
127
128 To compile this driver as a module, choose M here: the
129 module will be called atmel_mxt_ts.
130
131config TOUCHSCREEN_ATMEL_MXT_T37
132 bool "Support T37 Diagnostic Data"
133 depends on TOUCHSCREEN_ATMEL_MXT
134 depends on VIDEO_DEV=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_DEV=m)
135 select VIDEOBUF2_VMALLOC
136 help
137 Say Y here if you want support to output data from the T37
138 Diagnostic Data object using a V4L device.
139
140config TOUCHSCREEN_AUO_PIXCIR
141 tristate "AUO in-cell touchscreen using Pixcir ICs"
142 depends on I2C
143 depends on GPIOLIB || COMPILE_TEST
144 help
145 Say Y here if you have a AUO display with in-cell touchscreen
146 using Pixcir ICs.
147
148 If unsure, say N.
149
150 To compile this driver as a module, choose M here: the
151 module will be called auo-pixcir-ts.
152
153config TOUCHSCREEN_BU21013
154 tristate "BU21013 based touch panel controllers"
155 depends on I2C
156 help
157 Say Y here if you have a bu21013 touchscreen connected to
158 your system.
159
160 If unsure, say N.
161
162 To compile this driver as a module, choose M here: the
163 module will be called bu21013_ts.
164
165config TOUCHSCREEN_BU21029
166 tristate "Rohm BU21029 based touch panel controllers"
167 depends on I2C
168 help
169 Say Y here if you have a Rohm BU21029 touchscreen controller
170 connected to your system.
171
172 If unsure, say N.
173
174 To compile this driver as a module, choose M here: the
175 module will be called bu21029_ts.
176
177config TOUCHSCREEN_CHIPONE_ICN8318
178 tristate "chipone icn8318 touchscreen controller"
179 depends on GPIOLIB || COMPILE_TEST
180 depends on I2C
181 depends on OF
182 help
183 Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
184
185 If unsure, say N.
186
187 To compile this driver as a module, choose M here: the
188 module will be called chipone_icn8318.
189
190config TOUCHSCREEN_CHIPONE_ICN8505
191 tristate "chipone icn8505 touchscreen controller"
192 depends on I2C && ACPI
193 help
194 Say Y here if you have a ChipOne icn8505 based I2C touchscreen.
195
196 If unsure, say N.
197
198 To compile this driver as a module, choose M here: the
199 module will be called chipone_icn8505.
200
201config TOUCHSCREEN_CY8CTMA140
202 tristate "cy8ctma140 touchscreen"
203 depends on I2C
204 help
205 Say Y here if you have a Cypress CY8CTMA140 capacitive
206 touchscreen also just known as "TMA140"
207
208 If unsure, say N.
209
210 To compile this driver as a module, choose M here: the
211 module will be called cy8ctma140.
212
213config TOUCHSCREEN_CY8CTMG110
214 tristate "cy8ctmg110 touchscreen"
215 depends on I2C
216 depends on GPIOLIB || COMPILE_TEST
217 help
218 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
219 an AAVA device.
220
221 If unsure, say N.
222
223 To compile this driver as a module, choose M here: the
224 module will be called cy8ctmg110_ts.
225
226config TOUCHSCREEN_CYTTSP_CORE
227 tristate "Cypress TTSP touchscreen"
228 help
229 Say Y here if you have a touchscreen using controller from
230 the Cypress TrueTouch(tm) Standard Product family connected
231 to your system. You will also need to select appropriate
232 bus connection below.
233
234 If unsure, say N.
235
236 To compile this driver as a module, choose M here: the
237 module will be called cyttsp_core.
238
239config TOUCHSCREEN_CYTTSP_I2C
240 tristate "support I2C bus connection"
241 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
242 help
243 Say Y here if the touchscreen is connected via I2C bus.
244
245 To compile this driver as a module, choose M here: the
246 module will be called cyttsp_i2c.
247
248config TOUCHSCREEN_CYTTSP_SPI
249 tristate "support SPI bus connection"
250 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
251 help
252 Say Y here if the touchscreen is connected via SPI bus.
253
254 To compile this driver as a module, choose M here: the
255 module will be called cyttsp_spi.
256
257config TOUCHSCREEN_CYTTSP4_CORE
258 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
259 help
260 Core driver for Cypress TrueTouch(tm) Standard Product
261 Generation4 touchscreen controllers.
262
263 Say Y here if you have a Cypress Gen4 touchscreen.
264
265 If unsure, say N.
266
267 To compile this driver as a module, choose M here.
268
269config TOUCHSCREEN_CYTTSP4_I2C
270 tristate "support I2C bus connection"
271 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
272 help
273 Say Y here if the touchscreen is connected via I2C bus.
274
275 To compile this driver as a module, choose M here: the
276 module will be called cyttsp4_i2c.
277
278config TOUCHSCREEN_CYTTSP4_SPI
279 tristate "support SPI bus connection"
280 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
281 help
282 Say Y here if the touchscreen is connected via SPI bus.
283
284 To compile this driver as a module, choose M here: the
285 module will be called cyttsp4_spi.
286
287config TOUCHSCREEN_CYTTSP5
288 tristate "Cypress TrueTouch Gen5 Touchscreen Driver"
289 depends on I2C
290 select REGMAP_I2C
291 select CRC_ITU_T
292 help
293 Driver for Parade TrueTouch Standard Product Generation 5
294 touchscreen controllers. I2C bus interface support only.
295
296 Say Y here if you have a Cypress Gen5 touchscreen.
297
298 If unsure, say N.
299
300 To compile this driver as a module, choose M here: the
301 module will be called cyttsp5.
302
303config TOUCHSCREEN_DA9034
304 tristate "Touchscreen support for Dialog Semiconductor DA9034"
305 depends on PMIC_DA903X
306 default y
307 help
308 Say Y here to enable the support for the touchscreen found
309 on Dialog Semiconductor DA9034 PMIC.
310
311 If unsure, say N.
312
313 To compile this driver as a module, choose M here: the
314 module will be called da9034-ts.
315
316config TOUCHSCREEN_DA9052
317 tristate "Dialog DA9052/DA9053 TSI"
318 depends on PMIC_DA9052
319 help
320 Say Y here to support the touchscreen found on Dialog Semiconductor
321 DA9052-BC and DA9053-AA/Bx PMICs.
322
323 If unsure, say N.
324
325 To compile this driver as a module, choose M here: the
326 module will be called da9052_tsi.
327
328config TOUCHSCREEN_DYNAPRO
329 tristate "Dynapro serial touchscreen"
330 select SERIO
331 help
332 Say Y here if you have a Dynapro serial touchscreen connected to
333 your system.
334
335 If unsure, say N.
336
337 To compile this driver as a module, choose M here: the
338 module will be called dynapro.
339
340config TOUCHSCREEN_HAMPSHIRE
341 tristate "Hampshire serial touchscreen"
342 select SERIO
343 help
344 Say Y here if you have a Hampshire serial touchscreen connected to
345 your system.
346
347 If unsure, say N.
348
349 To compile this driver as a module, choose M here: the
350 module will be called hampshire.
351
352config TOUCHSCREEN_EETI
353 tristate "EETI touchscreen panel support"
354 depends on I2C
355 help
356 Say Y here to enable support for I2C connected EETI touch panels.
357
358 To compile this driver as a module, choose M here: the
359 module will be called eeti_ts.
360
361config TOUCHSCREEN_EGALAX
362 tristate "EETI eGalax multi-touch panel support"
363 depends on I2C && OF
364 help
365 Say Y here to enable support for I2C connected EETI
366 eGalax multi-touch panels.
367
368 To compile this driver as a module, choose M here: the
369 module will be called egalax_ts.
370
371config TOUCHSCREEN_EGALAX_SERIAL
372 tristate "EETI eGalax serial touchscreen"
373 select SERIO
374 help
375 Say Y here to enable support for serial connected EETI
376 eGalax touch panels.
377
378 To compile this driver as a module, choose M here: the
379 module will be called egalax_ts_serial.
380
381config TOUCHSCREEN_EXC3000
382 tristate "EETI EXC3000 multi-touch panel support"
383 depends on I2C
384 help
385 Say Y here to enable support for I2C connected EETI
386 EXC3000 multi-touch panels.
387
388 To compile this driver as a module, choose M here: the
389 module will be called exc3000.
390
391config TOUCHSCREEN_FUJITSU
392 tristate "Fujitsu serial touchscreen"
393 select SERIO
394 help
395 Say Y here if you have the Fujitsu touchscreen (such as one
396 installed in Lifebook P series laptop) connected to your
397 system.
398
399 If unsure, say N.
400
401 To compile this driver as a module, choose M here: the
402 module will be called fujitsu-ts.
403
404config TOUCHSCREEN_GOODIX
405 tristate "Goodix I2C touchscreen"
406 depends on I2C
407 depends on GPIOLIB || COMPILE_TEST
408 help
409 Say Y here if you have the Goodix touchscreen (such as one
410 installed in Onda v975w tablets) connected to your
411 system. It also supports 5-finger chip models, which can be
412 found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
413
414 If unsure, say N.
415
416 To compile this driver as a module, choose M here: the
417 module will be called goodix.
418
419config TOUCHSCREEN_HIDEEP
420 tristate "HiDeep Touch IC"
421 depends on I2C
422 help
423 Say Y here if you have a touchscreen using HiDeep.
424
425 If unsure, say N.
426
427 To compile this driver as a module, choose M here : the
428 module will be called hideep_ts.
429
430config TOUCHSCREEN_HYCON_HY46XX
431 tristate "Hycon hy46xx touchscreen support"
432 depends on I2C
433 help
434 Say Y here if you have a touchscreen using Hycon hy46xx
435
436 If unsure, say N.
437
438 To compile this driver as a module, choose M here: the
439 module will be called hycon-hy46xx.
440
441config TOUCHSCREEN_HYNITRON_CSTXXX
442 tristate "Hynitron touchscreen support"
443 depends on I2C
444 help
445 Say Y here if you have a touchscreen using a Hynitron
446 touchscreen controller.
447
448 If unsure, say N.
449
450 To compile this driver as a module, choose M here: the
451 module will be called hynitron-cstxxx.
452
453config TOUCHSCREEN_ILI210X
454 tristate "Ilitek ILI210X based touchscreen"
455 depends on I2C
456 select CRC_CCITT
457 help
458 Say Y here if you have a ILI210X based touchscreen
459 controller. This driver supports models ILI2102,
460 ILI2102s, ILI2103, ILI2103s and ILI2105.
461 Such kind of chipsets can be found in Amazon Kindle Fire
462 touchscreens.
463
464 If unsure, say N.
465
466 To compile this driver as a module, choose M here: the
467 module will be called ili210x.
468
469config TOUCHSCREEN_ILITEK
470 tristate "Ilitek I2C 213X/23XX/25XX/Lego Series Touch ICs"
471 depends on I2C
472 help
473 Say Y here if you have touchscreen with ILITEK touch IC,
474 it supports 213X/23XX/25XX and other Lego series.
475
476 If unsure, say N.
477
478 To compile this driver as a module, choose M here: the
479 module will be called ilitek_ts_i2c.
480
481config TOUCHSCREEN_IPROC
482 tristate "IPROC touch panel driver support"
483 depends on ARCH_BCM_IPROC || COMPILE_TEST
484 help
485 Say Y here if you want to add support for the IPROC touch
486 controller to your system.
487
488 If unsure, say N.
489
490 To compile this driver as a module, choose M here: the
491 module will be called bcm_iproc_tsc.
492
493config TOUCHSCREEN_S6SY761
494 tristate "Samsung S6SY761 Touchscreen driver"
495 depends on I2C
496 help
497 Say Y if you have the Samsung S6SY761 driver
498
499 If unsure, say N
500
501 To compile this driver as module, choose M here: the
502 module will be called s6sy761.
503
504config TOUCHSCREEN_GUNZE
505 tristate "Gunze AHL-51S touchscreen"
506 select SERIO
507 help
508 Say Y here if you have the Gunze AHL-51 touchscreen connected to
509 your system.
510
511 If unsure, say N.
512
513 To compile this driver as a module, choose M here: the
514 module will be called gunze.
515
516config TOUCHSCREEN_EKTF2127
517 tristate "Elan eKTF2127 I2C touchscreen"
518 depends on I2C
519 help
520 Say Y here if you have an Elan eKTF2127 touchscreen
521 connected to your system.
522
523 If unsure, say N.
524
525 To compile this driver as a module, choose M here: the
526 module will be called ektf2127.
527
528config TOUCHSCREEN_ELAN
529 tristate "Elan eKTH I2C touchscreen"
530 depends on I2C
531 help
532 Say Y here if you have an Elan eKTH I2C touchscreen
533 connected to your system.
534
535 If unsure, say N.
536
537 To compile this driver as a module, choose M here: the
538 module will be called elants_i2c.
539
540config TOUCHSCREEN_ELO
541 tristate "Elo serial touchscreens"
542 select SERIO
543 help
544 Say Y here if you have an Elo serial touchscreen connected to
545 your system.
546
547 If unsure, say N.
548
549 To compile this driver as a module, choose M here: the
550 module will be called elo.
551
552config TOUCHSCREEN_WACOM_W8001
553 tristate "Wacom W8001 penabled serial touchscreen"
554 select SERIO
555 help
556 Say Y here if you have an Wacom W8001 penabled serial touchscreen
557 connected to your system.
558
559 If unsure, say N.
560
561 To compile this driver as a module, choose M here: the
562 module will be called wacom_w8001.
563
564config TOUCHSCREEN_WACOM_I2C
565 tristate "Wacom Tablet support (I2C)"
566 depends on I2C
567 help
568 Say Y here if you want to use the I2C version of the Wacom
569 Pen Tablet.
570
571 If unsure, say N.
572
573 To compile this driver as a module, choose M here: the module
574 will be called wacom_i2c.
575
576config TOUCHSCREEN_LPC32XX
577 tristate "LPC32XX touchscreen controller"
578 depends on ARCH_LPC32XX
579 help
580 Say Y here if you have a LPC32XX device and want
581 to support the built-in touchscreen.
582
583 To compile this driver as a module, choose M here: the
584 module will be called lpc32xx_ts.
585
586config TOUCHSCREEN_MAX11801
587 tristate "MAX11801 based touchscreens"
588 depends on I2C
589 help
590 Say Y here if you have a MAX11801 based touchscreen
591 controller.
592
593 If unsure, say N.
594
595 To compile this driver as a module, choose M here: the
596 module will be called max11801_ts.
597
598config TOUCHSCREEN_MCS5000
599 tristate "MELFAS MCS-5000 touchscreen"
600 depends on I2C
601 help
602 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
603 chip in your system.
604
605 If unsure, say N.
606
607 To compile this driver as a module, choose M here: the
608 module will be called mcs5000_ts.
609
610config TOUCHSCREEN_MMS114
611 tristate "MELFAS MMS114 touchscreen"
612 depends on I2C
613 help
614 Say Y here if you have the MELFAS MMS114 touchscreen controller
615 chip in your system.
616
617 If unsure, say N.
618
619 To compile this driver as a module, choose M here: the
620 module will be called mms114.
621
622config TOUCHSCREEN_MELFAS_MIP4
623 tristate "MELFAS MIP4 Touchscreen"
624 depends on I2C
625 help
626 Say Y here if you have a MELFAS MIP4 Touchscreen device.
627
628 If unsure, say N.
629
630 To compile this driver as a module, choose M here:
631 the module will be called melfas_mip4.
632
633config TOUCHSCREEN_MSG2638
634 tristate "MStar msg2638 touchscreen support"
635 depends on I2C
636 depends on GPIOLIB || COMPILE_TEST
637 help
638 Say Y here if you have an I2C touchscreen using MStar msg2638.
639
640 If unsure, say N.
641
642 To compile this driver as a module, choose M here: the
643 module will be called msg2638.
644
645config TOUCHSCREEN_MTOUCH
646 tristate "MicroTouch serial touchscreens"
647 select SERIO
648 help
649 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
650 your system.
651
652 If unsure, say N.
653
654 To compile this driver as a module, choose M here: the
655 module will be called mtouch.
656
657config TOUCHSCREEN_NOVATEK_NVT_TS
658 tristate "Novatek NT11205 touchscreen support"
659 depends on I2C
660 help
661 Say Y here if you have a Novatek NT11205 touchscreen.
662 If unsure, say N.
663
664 To compile this driver as a module, choose M here: the
665 module will be called novatek-nvt-ts.
666
667config TOUCHSCREEN_IMAGIS
668 tristate "Imagis touchscreen support"
669 depends on I2C
670 help
671 Say Y here if you have an Imagis IST30xxC touchscreen.
672 If unsure, say N.
673
674 To compile this driver as a module, choose M here: the
675 module will be called imagis.
676
677config TOUCHSCREEN_IMX6UL_TSC
678 tristate "Freescale i.MX6UL touchscreen controller"
679 depends on ((OF && GPIOLIB) || COMPILE_TEST) && HAS_IOMEM
680 help
681 Say Y here if you have a Freescale i.MX6UL, and want to
682 use the internal touchscreen controller.
683
684 If unsure, say N.
685
686 To compile this driver as a module, choose M here: the
687 module will be called imx6ul_tsc.
688
689config TOUCHSCREEN_INEXIO
690 tristate "iNexio serial touchscreens"
691 select SERIO
692 help
693 Say Y here if you have an iNexio serial touchscreen connected to
694 your system.
695
696 If unsure, say N.
697
698 To compile this driver as a module, choose M here: the
699 module will be called inexio.
700
701config TOUCHSCREEN_MK712
702 tristate "ICS MicroClock MK712 touchscreen"
703 depends on ISA
704 help
705 Say Y here if you have the ICS MicroClock MK712 touchscreen
706 controller chip in your system.
707
708 If unsure, say N.
709
710 To compile this driver as a module, choose M here: the
711 module will be called mk712.
712
713config TOUCHSCREEN_HP600
714 tristate "HP Jornada 6xx touchscreen"
715 depends on SH_HP6XX && SH_ADC
716 help
717 Say Y here if you have a HP Jornada 620/660/680/690 and want to
718 support the built-in touchscreen.
719
720 To compile this driver as a module, choose M here: the
721 module will be called hp680_ts_input.
722
723config TOUCHSCREEN_HP7XX
724 tristate "HP Jornada 7xx touchscreen"
725 depends on SA1100_JORNADA720_SSP
726 help
727 Say Y here if you have a HP Jornada 710/720/728 and want
728 to support the built-in touchscreen.
729
730 To compile this driver as a module, choose M here: the
731 module will be called jornada720_ts.
732
733config TOUCHSCREEN_IPAQ_MICRO
734 tristate "HP iPAQ Atmel Micro ASIC touchscreen"
735 depends on MFD_IPAQ_MICRO
736 help
737 Say Y here to enable support for the touchscreen attached to
738 the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
739
740 If unsure, say N.
741
742 To compile this driver as a module, choose M here: the
743 module will be called ipaq-micro-ts.
744
745config TOUCHSCREEN_HTCPEN
746 tristate "HTC Shift X9500 touchscreen"
747 depends on ISA
748 help
749 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
750 Clio / Shangrila and want to support the built-in touchscreen.
751
752 If unsure, say N.
753
754 To compile this driver as a module, choose M here: the
755 module will be called htcpen.
756
757config TOUCHSCREEN_PENMOUNT
758 tristate "Penmount serial touchscreen"
759 select SERIO
760 help
761 Say Y here if you have a Penmount serial touchscreen connected to
762 your system.
763
764 If unsure, say N.
765
766 To compile this driver as a module, choose M here: the
767 module will be called penmount.
768
769config TOUCHSCREEN_EDT_FT5X06
770 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
771 depends on I2C
772 select REGMAP_I2C
773 help
774 Say Y here if you have an EDT "Polytouch" touchscreen based
775 on the FocalTech FT5x06 family of controllers connected to
776 your system.
777
778 If unsure, say N.
779
780 To compile this driver as a module, choose M here: the
781 module will be called edt-ft5x06.
782
783config TOUCHSCREEN_RASPBERRYPI_FW
784 tristate "Raspberry Pi's firmware base touch screen support"
785 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
786 help
787 Say Y here if you have the official Raspberry Pi 7 inch screen on
788 your system.
789
790 If unsure, say N.
791
792 To compile this driver as a module, choose M here: the
793 module will be called raspberrypi-ts.
794
795config TOUCHSCREEN_MIGOR
796 tristate "Renesas MIGO-R touchscreen"
797 depends on (SH_MIGOR || COMPILE_TEST) && I2C
798 help
799 Say Y here to enable MIGO-R touchscreen support.
800
801 If unsure, say N.
802
803 To compile this driver as a module, choose M here: the
804 module will be called migor_ts.
805
806config TOUCHSCREEN_TOUCHRIGHT
807 tristate "Touchright serial touchscreen"
808 select SERIO
809 help
810 Say Y here if you have a Touchright serial touchscreen connected to
811 your system.
812
813 If unsure, say N.
814
815 To compile this driver as a module, choose M here: the
816 module will be called touchright.
817
818config TOUCHSCREEN_TOUCHWIN
819 tristate "Touchwin serial touchscreen"
820 select SERIO
821 help
822 Say Y here if you have a Touchwin serial touchscreen connected to
823 your system.
824
825 If unsure, say N.
826
827 To compile this driver as a module, choose M here: the
828 module will be called touchwin.
829
830config TOUCHSCREEN_TI_AM335X_TSC
831 tristate "TI Touchscreen Interface"
832 depends on MFD_TI_AM335X_TSCADC
833 help
834 Say Y here if you have 4/5/8 wire touchscreen controller
835 to be connected to the ADC controller on your TI AM335x SoC.
836
837 If unsure, say N.
838
839 To compile this driver as a module, choose M here: the
840 module will be called ti_am335x_tsc.
841
842config TOUCHSCREEN_PIXCIR
843 tristate "PIXCIR I2C touchscreens"
844 depends on I2C
845 help
846 Say Y here if you have a pixcir i2c touchscreen
847 controller.
848
849 If unsure, say N.
850
851 To compile this driver as a module, choose M here: the
852 module will be called pixcir_i2c_ts.
853
854config TOUCHSCREEN_WDT87XX_I2C
855 tristate "Weida HiTech I2C touchscreen"
856 depends on I2C
857 help
858 Say Y here if you have a Weida WDT87XX I2C touchscreen
859 connected to your system.
860
861 If unsure, say N.
862
863 To compile this driver as a module, choose M here: the
864 module will be called wdt87xx_i2c.
865
866config TOUCHSCREEN_WM831X
867 tristate "Support for WM831x touchscreen controllers"
868 depends on MFD_WM831X
869 help
870 This enables support for the touchscreen controller on the WM831x
871 series of PMICs.
872
873 To compile this driver as a module, choose M here: the
874 module will be called wm831x-ts.
875
876config TOUCHSCREEN_WM97XX
877 tristate "Support for WM97xx AC97 touchscreen controllers"
878 depends on AC97_BUS || AC97_BUS_NEW
879 help
880 Say Y here if you have a Wolfson Microelectronics WM97xx
881 touchscreen connected to your system. Note that this option
882 only enables core driver, you will also need to select
883 support for appropriate chip below.
884
885 If unsure, say N.
886
887 To compile this driver as a module, choose M here: the
888 module will be called wm97xx-ts.
889
890config TOUCHSCREEN_WM9705
891 bool "WM9705 Touchscreen interface support"
892 depends on TOUCHSCREEN_WM97XX
893 default y
894 help
895 Say Y here to enable support for the Wolfson Microelectronics
896 WM9705 touchscreen controller.
897
898config TOUCHSCREEN_WM9712
899 bool "WM9712 Touchscreen interface support"
900 depends on TOUCHSCREEN_WM97XX
901 default y
902 help
903 Say Y here to enable support for the Wolfson Microelectronics
904 WM9712 touchscreen controller.
905
906config TOUCHSCREEN_WM9713
907 bool "WM9713 Touchscreen interface support"
908 depends on TOUCHSCREEN_WM97XX
909 default y
910 help
911 Say Y here to enable support for the Wolfson Microelectronics
912 WM9713 touchscreen controller.
913
914config TOUCHSCREEN_WM97XX_MAINSTONE
915 tristate "WM97xx Mainstone/Palm accelerated touch"
916 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
917 depends on SND_PXA2XX_LIB_AC97
918 help
919 Say Y here for support for streaming mode with WM97xx touchscreens
920 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
921
922 If unsure, say N.
923
924 To compile this driver as a module, choose M here: the
925 module will be called mainstone-wm97xx.
926
927config TOUCHSCREEN_USB_COMPOSITE
928 tristate "USB Touchscreen Driver"
929 depends on USB_ARCH_HAS_HCD
930 select USB
931 help
932 USB Touchscreen driver for:
933 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
934 - PanJit TouchSet USB
935 - 3M MicroTouch USB (EX II series)
936 - ITM
937 - some other eTurboTouch
938 - Gunze AHL61
939 - DMC TSC-10/25
940 - IRTOUCHSYSTEMS/UNITOP
941 - IdealTEK URTC1000
942 - GoTop Super_Q2/GogoPen/PenPower tablets
943 - JASTEC USB Touch Controller/DigiTech DTR-02U
944 - Zytronic controllers
945 - Elo TouchSystems 2700 IntelliTouch
946 - EasyTouch USB Touch Controller from Data Module
947 - e2i (Mimo monitors)
948
949 Have a look at <http://linux.chapter7.ch/touchkit/> for
950 a usage description and the required user-space stuff.
951
952 To compile this driver as a module, choose M here: the
953 module will be called usbtouchscreen.
954
955config TOUCHSCREEN_MXS_LRADC
956 tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
957 depends on MFD_MXS_LRADC
958 help
959 Say Y here if you have a touchscreen connected to the low-resolution
960 analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
961
962 To compile this driver as a module, choose M here: the module will be
963 called mxs-lradc-ts.
964
965config TOUCHSCREEN_MX25
966 tristate "Freescale i.MX25 touchscreen input driver"
967 depends on MFD_MX25_TSADC
968 help
969 Enable support for touchscreen connected to your i.MX25.
970
971 To compile this driver as a module, choose M here: the
972 module will be called fsl-imx25-tcq.
973
974config TOUCHSCREEN_MC13783
975 tristate "Freescale MC13783 touchscreen input driver"
976 depends on MFD_MC13XXX
977 help
978 Say Y here if you have an Freescale MC13783 PMIC on your
979 board and want to use its touchscreen
980
981 If unsure, say N.
982
983 To compile this driver as a module, choose M here: the
984 module will be called mc13783_ts.
985
986config TOUCHSCREEN_USB_EGALAX
987 default y
988 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
989 depends on TOUCHSCREEN_USB_COMPOSITE
990
991config TOUCHSCREEN_USB_PANJIT
992 default y
993 bool "PanJit device support" if EXPERT
994 depends on TOUCHSCREEN_USB_COMPOSITE
995
996config TOUCHSCREEN_USB_3M
997 default y
998 bool "3M/Microtouch EX II series device support" if EXPERT
999 depends on TOUCHSCREEN_USB_COMPOSITE
1000
1001config TOUCHSCREEN_USB_ITM
1002 default y
1003 bool "ITM device support" if EXPERT
1004 depends on TOUCHSCREEN_USB_COMPOSITE
1005
1006config TOUCHSCREEN_USB_ETURBO
1007 default y
1008 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
1009 depends on TOUCHSCREEN_USB_COMPOSITE
1010
1011config TOUCHSCREEN_USB_GUNZE
1012 default y
1013 bool "Gunze AHL61 device support" if EXPERT
1014 depends on TOUCHSCREEN_USB_COMPOSITE
1015
1016config TOUCHSCREEN_USB_DMC_TSC10
1017 default y
1018 bool "DMC TSC-10/25 device support" if EXPERT
1019 depends on TOUCHSCREEN_USB_COMPOSITE
1020
1021config TOUCHSCREEN_USB_IRTOUCH
1022 default y
1023 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
1024 depends on TOUCHSCREEN_USB_COMPOSITE
1025
1026config TOUCHSCREEN_USB_IDEALTEK
1027 default y
1028 bool "IdealTEK URTC1000 device support" if EXPERT
1029 depends on TOUCHSCREEN_USB_COMPOSITE
1030
1031config TOUCHSCREEN_USB_GENERAL_TOUCH
1032 default y
1033 bool "GeneralTouch Touchscreen device support" if EXPERT
1034 depends on TOUCHSCREEN_USB_COMPOSITE
1035
1036config TOUCHSCREEN_USB_GOTOP
1037 default y
1038 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
1039 depends on TOUCHSCREEN_USB_COMPOSITE
1040
1041config TOUCHSCREEN_USB_JASTEC
1042 default y
1043 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
1044 depends on TOUCHSCREEN_USB_COMPOSITE
1045
1046config TOUCHSCREEN_USB_ELO
1047 default y
1048 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
1049 depends on TOUCHSCREEN_USB_COMPOSITE
1050
1051config TOUCHSCREEN_USB_E2I
1052 default y
1053 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
1054 depends on TOUCHSCREEN_USB_COMPOSITE
1055
1056config TOUCHSCREEN_USB_ZYTRONIC
1057 default y
1058 bool "Zytronic controller" if EXPERT
1059 depends on TOUCHSCREEN_USB_COMPOSITE
1060
1061config TOUCHSCREEN_USB_ETT_TC45USB
1062 default y
1063 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
1064 depends on TOUCHSCREEN_USB_COMPOSITE
1065
1066config TOUCHSCREEN_USB_NEXIO
1067 default y
1068 bool "NEXIO/iNexio device support" if EXPERT
1069 depends on TOUCHSCREEN_USB_COMPOSITE
1070
1071config TOUCHSCREEN_USB_EASYTOUCH
1072 default y
1073 bool "EasyTouch USB Touch controller device support" if EXPERT
1074 depends on TOUCHSCREEN_USB_COMPOSITE
1075 help
1076 Say Y here if you have an EasyTouch USB Touch controller.
1077 If unsure, say N.
1078
1079config TOUCHSCREEN_TOUCHIT213
1080 tristate "Sahara TouchIT-213 touchscreen"
1081 select SERIO
1082 help
1083 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
1084
1085 If unsure, say N.
1086
1087 To compile this driver as a module, choose M here: the
1088 module will be called touchit213.
1089
1090config TOUCHSCREEN_TS4800
1091 tristate "TS-4800 touchscreen"
1092 depends on HAS_IOMEM && OF
1093 depends on SOC_IMX51 || COMPILE_TEST
1094 select MFD_SYSCON
1095 help
1096 Say Y here if you have a touchscreen on a TS-4800 board.
1097
1098 On TS-4800, the touchscreen is not handled directly by Linux but by
1099 a companion FPGA.
1100
1101 If unsure, say N.
1102
1103 To compile this driver as a module, choose M here: the
1104 module will be called ts4800_ts.
1105
1106config TOUCHSCREEN_TSC_SERIO
1107 tristate "TSC-10/25/40 serial touchscreen support"
1108 select SERIO
1109 help
1110 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
1111 to your system.
1112
1113 If unsure, say N.
1114
1115 To compile this driver as a module, choose M here: the
1116 module will be called tsc40.
1117
1118config TOUCHSCREEN_TSC200X_CORE
1119 tristate
1120
1121config TOUCHSCREEN_TSC2004
1122 tristate "TSC2004 based touchscreens"
1123 depends on I2C
1124 select REGMAP_I2C
1125 select TOUCHSCREEN_TSC200X_CORE
1126 help
1127 Say Y here if you have a TSC2004 based touchscreen.
1128
1129 If unsure, say N.
1130
1131 To compile this driver as a module, choose M here: the
1132 module will be called tsc2004.
1133
1134config TOUCHSCREEN_TSC2005
1135 tristate "TSC2005 based touchscreens"
1136 depends on SPI_MASTER
1137 select REGMAP_SPI
1138 select TOUCHSCREEN_TSC200X_CORE
1139 help
1140 Say Y here if you have a TSC2005 based touchscreen.
1141
1142 If unsure, say N.
1143
1144 To compile this driver as a module, choose M here: the
1145 module will be called tsc2005.
1146
1147config TOUCHSCREEN_TSC2007
1148 tristate "TSC2007 based touchscreens"
1149 depends on I2C
1150 help
1151 Say Y here if you have a TSC2007 based touchscreen.
1152
1153 If unsure, say N.
1154
1155 To compile this driver as a module, choose M here: the
1156 module will be called tsc2007.
1157
1158config TOUCHSCREEN_TSC2007_IIO
1159 bool "IIO interface for external ADC input and temperature"
1160 depends on TOUCHSCREEN_TSC2007
1161 depends on IIO=y || IIO=TOUCHSCREEN_TSC2007
1162 help
1163 Saying Y here adds an iio interface to the tsc2007 which
1164 provides values for the AUX input (used for e.g. battery
1165 or ambient light monitoring), temperature and raw input
1166 values.
1167
1168config TOUCHSCREEN_PCAP
1169 tristate "Motorola PCAP touchscreen"
1170 depends on EZX_PCAP
1171 help
1172 Say Y here if you have a Motorola EZX telephone and
1173 want to enable support for the built-in touchscreen.
1174
1175 To compile this driver as a module, choose M here: the
1176 module will be called pcap_ts.
1177
1178config TOUCHSCREEN_RM_TS
1179 tristate "Raydium I2C Touchscreen"
1180 depends on I2C
1181 depends on GPIOLIB || COMPILE_TEST
1182 help
1183 Say Y here if you have Raydium series I2C touchscreen,
1184 such as RM32380, connected to your system.
1185
1186 If unsure, say N.
1187
1188 To compile this driver as a module, choose M here: the
1189 module will be called raydium_i2c_ts.
1190
1191config TOUCHSCREEN_SILEAD
1192 tristate "Silead I2C touchscreen"
1193 depends on I2C
1194 help
1195 Say Y here if you have the Silead touchscreen connected to
1196 your system.
1197
1198 If unsure, say N.
1199
1200 To compile this driver as a module, choose M here: the
1201 module will be called silead.
1202
1203config TOUCHSCREEN_SIS_I2C
1204 tristate "SiS 9200 family I2C touchscreen"
1205 depends on I2C
1206 select CRC_ITU_T
1207 depends on GPIOLIB || COMPILE_TEST
1208 help
1209 This enables support for SiS 9200 family over I2C based touchscreens.
1210
1211 If unsure, say N.
1212
1213 To compile this driver as a module, choose M here: the
1214 module will be called sis_i2c.
1215
1216config TOUCHSCREEN_ST1232
1217 tristate "Sitronix ST1232 or ST1633 touchscreen controllers"
1218 depends on I2C
1219 help
1220 Say Y here if you want to support the Sitronix ST1232
1221 or ST1633 touchscreen controller.
1222
1223 If unsure, say N.
1224
1225 To compile this driver as a module, choose M here: the
1226 module will be called st1232_ts.
1227
1228config TOUCHSCREEN_STMFTS
1229 tristate "STMicroelectronics STMFTS touchscreen"
1230 depends on I2C
1231 depends on LEDS_CLASS
1232 help
1233 Say Y here if you want support for STMicroelectronics
1234 STMFTS touchscreen.
1235
1236 To compile this driver as a module, choose M here: the
1237 module will be called stmfts.
1238
1239config TOUCHSCREEN_STMPE
1240 tristate "STMicroelectronics STMPE touchscreens"
1241 depends on MFD_STMPE
1242 depends on OF
1243 help
1244 Say Y here if you want support for STMicroelectronics
1245 STMPE touchscreen controllers.
1246
1247 To compile this driver as a module, choose M here: the
1248 module will be called stmpe-ts.
1249
1250config TOUCHSCREEN_SUN4I
1251 tristate "Allwinner sun4i resistive touchscreen controller support"
1252 depends on ARCH_SUNXI || COMPILE_TEST
1253 depends on HWMON
1254 depends on THERMAL || !THERMAL_OF
1255 help
1256 This selects support for the resistive touchscreen controller
1257 found on Allwinner sunxi SoCs.
1258
1259 To compile this driver as a module, choose M here: the
1260 module will be called sun4i-ts.
1261
1262config TOUCHSCREEN_SUR40
1263 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
1264 depends on USB && MEDIA_USB_SUPPORT && HAS_DMA
1265 depends on VIDEO_DEV
1266 select VIDEOBUF2_DMA_SG
1267 help
1268 Say Y here if you want support for the Samsung SUR40 touchscreen
1269 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
1270
1271 To compile this driver as a module, choose M here: the
1272 module will be called sur40.
1273
1274config TOUCHSCREEN_SURFACE3_SPI
1275 tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
1276 depends on SPI
1277 depends on GPIOLIB || COMPILE_TEST
1278 help
1279 Say Y here if you have the Ntrig/Microsoft SPI touchscreen
1280 controller chip as found on the Surface 3 in your system.
1281
1282 If unsure, say N.
1283
1284 To compile this driver as a module, choose M here: the
1285 module will be called surface3_spi.
1286
1287config TOUCHSCREEN_SX8654
1288 tristate "Semtech SX8654 touchscreen"
1289 depends on I2C
1290 help
1291 Say Y here if you have a Semtech SX8654 touchscreen controller.
1292
1293 If unsure, say N
1294
1295 To compile this driver as a module, choose M here: the
1296 module will be called sx8654.
1297
1298config TOUCHSCREEN_TPS6507X
1299 tristate "TPS6507x based touchscreens"
1300 depends on I2C
1301 help
1302 Say Y here if you have a TPS6507x based touchscreen
1303 controller.
1304
1305 If unsure, say N.
1306
1307 To compile this driver as a module, choose M here: the
1308 module will be called tps6507x_ts.
1309
1310config TOUCHSCREEN_ZET6223
1311 tristate "Zeitec ZET6223 touchscreen driver"
1312 depends on I2C
1313 help
1314 Say Y here if you have a touchscreen using Zeitec ZET6223
1315
1316 If unsure, say N.
1317
1318 To compile this driver as a module, choose M here: the
1319 module will be called zet6223.
1320
1321config TOUCHSCREEN_ZFORCE
1322 tristate "Neonode zForce infrared touchscreens"
1323 depends on I2C
1324 depends on GPIOLIB || COMPILE_TEST
1325 help
1326 Say Y here if you have a touchscreen using the zforce
1327 infraread technology from Neonode.
1328
1329 If unsure, say N.
1330
1331 To compile this driver as a module, choose M here: the
1332 module will be called zforce_ts.
1333
1334config TOUCHSCREEN_COLIBRI_VF50
1335 tristate "Toradex Colibri on board touchscreen driver"
1336 depends on IIO
1337 depends on GPIOLIB || COMPILE_TEST
1338 help
1339 Say Y here if you have a Colibri VF50 and plan to use
1340 the on-board provided 4-wire touchscreen driver.
1341
1342 If unsure, say N.
1343
1344 To compile this driver as a module, choose M here: the
1345 module will be called colibri_vf50_ts.
1346
1347config TOUCHSCREEN_ROHM_BU21023
1348 tristate "ROHM BU21023/24 Dual touch support resistive touchscreens"
1349 depends on I2C
1350 help
1351 Say Y here if you have a touchscreen using ROHM BU21023/24.
1352
1353 If unsure, say N.
1354
1355 To compile this driver as a module, choose M here: the
1356 module will be called bu21023_ts.
1357
1358config TOUCHSCREEN_IQS5XX
1359 tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
1360 depends on I2C
1361 help
1362 Say Y to enable support for the Azoteq IQS550/572/525
1363 family of trackpad/touchscreen controllers.
1364
1365 To compile this driver as a module, choose M here: the
1366 module will be called iqs5xx.
1367
1368config TOUCHSCREEN_IQS7211
1369 tristate "Azoteq IQS7210A/7211A/E trackpad/touchscreen controller"
1370 depends on I2C
1371 help
1372 Say Y to enable support for the Azoteq IQS7210A/7211A/E
1373 family of trackpad/touchscreen controllers.
1374
1375 To compile this driver as a module, choose M here: the
1376 module will be called iqs7211.
1377
1378config TOUCHSCREEN_ZINITIX
1379 tristate "Zinitix touchscreen support"
1380 depends on I2C
1381 help
1382 Say Y here if you have a touchscreen using Zinitix bt541,
1383 or something similar enough.
1384
1385 If unsure, say N.
1386
1387 To compile this driver as a module, choose M here: the
1388 module will be called zinitix.
1389
1390config TOUCHSCREEN_HIMAX_HX83112B
1391 tristate "Himax hx83112b touchscreen driver"
1392 depends on I2C
1393 select REGMAP_I2C
1394 help
1395 Say Y here to enable support for Himax hx83112b touchscreens.
1396
1397 If unsure, say N.
1398
1399 To compile this driver as a module, choose M here: the
1400 module will be called himax_hx83112b.
1401
1402endif
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Touchscreen driver configuration
4#
5menuconfig INPUT_TOUCHSCREEN
6 bool "Touchscreens"
7 help
8 Say Y here, and a list of supported touchscreens will be displayed.
9 This option doesn't affect the kernel.
10
11 If unsure, say Y.
12
13if INPUT_TOUCHSCREEN
14
15config TOUCHSCREEN_88PM860X
16 tristate "Marvell 88PM860x touchscreen"
17 depends on MFD_88PM860X
18 help
19 Say Y here if you have a 88PM860x PMIC and want to enable
20 support for the built-in touchscreen.
21
22 If unsure, say N.
23
24 To compile this driver as a module, choose M here: the
25 module will be called 88pm860x-ts.
26
27config TOUCHSCREEN_ADS7846
28 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on SPI_MASTER
30 depends on HWMON = n || HWMON
31 help
32 Say Y here if you have a touchscreen interface using the
33 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
34 and your board-specific setup code includes that in its
35 table of SPI devices.
36
37 If HWMON is selected, and the driver is told the reference voltage
38 on your board, you will also get hwmon interfaces for the voltage
39 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40
41 If unsure, say N (but it's safe to say "Y").
42
43 To compile this driver as a module, choose M here: the
44 module will be called ads7846.
45
46config TOUCHSCREEN_AD7877
47 tristate "AD7877 based touchscreens"
48 depends on SPI_MASTER
49 help
50 Say Y here if you have a touchscreen interface using the
51 AD7877 controller, and your board-specific initialization
52 code includes that in its table of SPI devices.
53
54 If unsure, say N (but it's safe to say "Y").
55
56 To compile this driver as a module, choose M here: the
57 module will be called ad7877.
58
59config TOUCHSCREEN_AD7879
60 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 help
62 Say Y here if you want to support a touchscreen interface using
63 the AD7879-1/AD7889-1 controller.
64
65 You should select a bus connection too.
66
67 To compile this driver as a module, choose M here: the
68 module will be called ad7879.
69
70config TOUCHSCREEN_AD7879_I2C
71 tristate "support I2C bus connection"
72 depends on TOUCHSCREEN_AD7879 && I2C
73 select REGMAP_I2C
74 help
75 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
76
77 To compile this driver as a module, choose M here: the
78 module will be called ad7879-i2c.
79
80config TOUCHSCREEN_AD7879_SPI
81 tristate "support SPI bus connection"
82 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
83 select REGMAP_SPI
84 help
85 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
86
87 If unsure, say N (but it's safe to say "Y").
88
89 To compile this driver as a module, choose M here: the
90 module will be called ad7879-spi.
91
92config TOUCHSCREEN_ADC
93 tristate "Generic ADC based resistive touchscreen"
94 depends on IIO
95 select IIO_BUFFER
96 select IIO_BUFFER_CB
97 help
98 Say Y here if you want to use the generic ADC
99 resistive touchscreen driver.
100
101 If unsure, say N (but it's safe to say "Y").
102
103 To compile this driver as a module, choose M here: the
104 module will be called resistive-adc-touch.ko.
105
106config TOUCHSCREEN_AR1021_I2C
107 tristate "Microchip AR1020/1021 i2c touchscreen"
108 depends on I2C && OF
109 help
110 Say Y here if you have the Microchip AR1020 or AR1021 touchscreen
111 controller chip in your system.
112
113 If unsure, say N.
114
115 To compile this driver as a module, choose M here: the
116 module will be called ar1021_i2c.
117
118config TOUCHSCREEN_ATMEL_MXT
119 tristate "Atmel mXT I2C Touchscreen"
120 depends on I2C
121 select FW_LOADER
122 help
123 Say Y here if you have Atmel mXT series I2C touchscreen,
124 such as AT42QT602240/ATMXT224, connected to your system.
125
126 If unsure, say N.
127
128 To compile this driver as a module, choose M here: the
129 module will be called atmel_mxt_ts.
130
131config TOUCHSCREEN_ATMEL_MXT_T37
132 bool "Support T37 Diagnostic Data"
133 depends on TOUCHSCREEN_ATMEL_MXT
134 depends on VIDEO_V4L2=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_V4L2=m)
135 select VIDEOBUF2_VMALLOC
136 help
137 Say Y here if you want support to output data from the T37
138 Diagnostic Data object using a V4L device.
139
140config TOUCHSCREEN_AUO_PIXCIR
141 tristate "AUO in-cell touchscreen using Pixcir ICs"
142 depends on I2C
143 depends on GPIOLIB || COMPILE_TEST
144 help
145 Say Y here if you have a AUO display with in-cell touchscreen
146 using Pixcir ICs.
147
148 If unsure, say N.
149
150 To compile this driver as a module, choose M here: the
151 module will be called auo-pixcir-ts.
152
153config TOUCHSCREEN_BU21013
154 tristate "BU21013 based touch panel controllers"
155 depends on I2C
156 help
157 Say Y here if you have a bu21013 touchscreen connected to
158 your system.
159
160 If unsure, say N.
161
162 To compile this driver as a module, choose M here: the
163 module will be called bu21013_ts.
164
165config TOUCHSCREEN_BU21029
166 tristate "Rohm BU21029 based touch panel controllers"
167 depends on I2C
168 help
169 Say Y here if you have a Rohm BU21029 touchscreen controller
170 connected to your system.
171
172 If unsure, say N.
173
174 To compile this driver as a module, choose M here: the
175 module will be called bu21029_ts.
176
177config TOUCHSCREEN_CHIPONE_ICN8318
178 tristate "chipone icn8318 touchscreen controller"
179 depends on GPIOLIB || COMPILE_TEST
180 depends on I2C
181 depends on OF
182 help
183 Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
184
185 If unsure, say N.
186
187 To compile this driver as a module, choose M here: the
188 module will be called chipone_icn8318.
189
190config TOUCHSCREEN_CHIPONE_ICN8505
191 tristate "chipone icn8505 touchscreen controller"
192 depends on I2C && ACPI
193 help
194 Say Y here if you have a ChipOne icn8505 based I2C touchscreen.
195
196 If unsure, say N.
197
198 To compile this driver as a module, choose M here: the
199 module will be called chipone_icn8505.
200
201config TOUCHSCREEN_CY8CTMA140
202 tristate "cy8ctma140 touchscreen"
203 depends on I2C
204 help
205 Say Y here if you have a Cypress CY8CTMA140 capacitive
206 touchscreen also just known as "TMA140"
207
208 If unsure, say N.
209
210 To compile this driver as a module, choose M here: the
211 module will be called cy8ctma140.
212
213config TOUCHSCREEN_CY8CTMG110
214 tristate "cy8ctmg110 touchscreen"
215 depends on I2C
216 depends on GPIOLIB || COMPILE_TEST
217 help
218 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
219 an AAVA device.
220
221 If unsure, say N.
222
223 To compile this driver as a module, choose M here: the
224 module will be called cy8ctmg110_ts.
225
226config TOUCHSCREEN_CYTTSP_CORE
227 tristate "Cypress TTSP touchscreen"
228 help
229 Say Y here if you have a touchscreen using controller from
230 the Cypress TrueTouch(tm) Standard Product family connected
231 to your system. You will also need to select appropriate
232 bus connection below.
233
234 If unsure, say N.
235
236 To compile this driver as a module, choose M here: the
237 module will be called cyttsp_core.
238
239config TOUCHSCREEN_CYTTSP_I2C
240 tristate "support I2C bus connection"
241 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
242 help
243 Say Y here if the touchscreen is connected via I2C bus.
244
245 To compile this driver as a module, choose M here: the
246 module will be called cyttsp_i2c.
247
248config TOUCHSCREEN_CYTTSP_SPI
249 tristate "support SPI bus connection"
250 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
251 help
252 Say Y here if the touchscreen is connected via SPI bus.
253
254 To compile this driver as a module, choose M here: the
255 module will be called cyttsp_spi.
256
257config TOUCHSCREEN_CYTTSP4_CORE
258 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
259 help
260 Core driver for Cypress TrueTouch(tm) Standard Product
261 Generation4 touchscreen controllers.
262
263 Say Y here if you have a Cypress Gen4 touchscreen.
264
265 If unsure, say N.
266
267 To compile this driver as a module, choose M here.
268
269config TOUCHSCREEN_CYTTSP4_I2C
270 tristate "support I2C bus connection"
271 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
272 help
273 Say Y here if the touchscreen is connected via I2C bus.
274
275 To compile this driver as a module, choose M here: the
276 module will be called cyttsp4_i2c.
277
278config TOUCHSCREEN_CYTTSP4_SPI
279 tristate "support SPI bus connection"
280 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
281 help
282 Say Y here if the touchscreen is connected via SPI bus.
283
284 To compile this driver as a module, choose M here: the
285 module will be called cyttsp4_spi.
286
287config TOUCHSCREEN_DA9034
288 tristate "Touchscreen support for Dialog Semiconductor DA9034"
289 depends on PMIC_DA903X
290 default y
291 help
292 Say Y here to enable the support for the touchscreen found
293 on Dialog Semiconductor DA9034 PMIC.
294
295 If unsure, say N.
296
297 To compile this driver as a module, choose M here: the
298 module will be called da9034-ts.
299
300config TOUCHSCREEN_DA9052
301 tristate "Dialog DA9052/DA9053 TSI"
302 depends on PMIC_DA9052
303 help
304 Say Y here to support the touchscreen found on Dialog Semiconductor
305 DA9052-BC and DA9053-AA/Bx PMICs.
306
307 If unsure, say N.
308
309 To compile this driver as a module, choose M here: the
310 module will be called da9052_tsi.
311
312config TOUCHSCREEN_DYNAPRO
313 tristate "Dynapro serial touchscreen"
314 select SERIO
315 help
316 Say Y here if you have a Dynapro serial touchscreen connected to
317 your system.
318
319 If unsure, say N.
320
321 To compile this driver as a module, choose M here: the
322 module will be called dynapro.
323
324config TOUCHSCREEN_HAMPSHIRE
325 tristate "Hampshire serial touchscreen"
326 select SERIO
327 help
328 Say Y here if you have a Hampshire serial touchscreen connected to
329 your system.
330
331 If unsure, say N.
332
333 To compile this driver as a module, choose M here: the
334 module will be called hampshire.
335
336config TOUCHSCREEN_EETI
337 tristate "EETI touchscreen panel support"
338 depends on I2C
339 help
340 Say Y here to enable support for I2C connected EETI touch panels.
341
342 To compile this driver as a module, choose M here: the
343 module will be called eeti_ts.
344
345config TOUCHSCREEN_EGALAX
346 tristate "EETI eGalax multi-touch panel support"
347 depends on I2C && OF
348 help
349 Say Y here to enable support for I2C connected EETI
350 eGalax multi-touch panels.
351
352 To compile this driver as a module, choose M here: the
353 module will be called egalax_ts.
354
355config TOUCHSCREEN_EGALAX_SERIAL
356 tristate "EETI eGalax serial touchscreen"
357 select SERIO
358 help
359 Say Y here to enable support for serial connected EETI
360 eGalax touch panels.
361
362 To compile this driver as a module, choose M here: the
363 module will be called egalax_ts_serial.
364
365config TOUCHSCREEN_EXC3000
366 tristate "EETI EXC3000 multi-touch panel support"
367 depends on I2C
368 help
369 Say Y here to enable support for I2C connected EETI
370 EXC3000 multi-touch panels.
371
372 To compile this driver as a module, choose M here: the
373 module will be called exc3000.
374
375config TOUCHSCREEN_FUJITSU
376 tristate "Fujitsu serial touchscreen"
377 select SERIO
378 help
379 Say Y here if you have the Fujitsu touchscreen (such as one
380 installed in Lifebook P series laptop) connected to your
381 system.
382
383 If unsure, say N.
384
385 To compile this driver as a module, choose M here: the
386 module will be called fujitsu-ts.
387
388config TOUCHSCREEN_GOODIX
389 tristate "Goodix I2C touchscreen"
390 depends on I2C
391 depends on GPIOLIB || COMPILE_TEST
392 help
393 Say Y here if you have the Goodix touchscreen (such as one
394 installed in Onda v975w tablets) connected to your
395 system. It also supports 5-finger chip models, which can be
396 found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
397
398 If unsure, say N.
399
400 To compile this driver as a module, choose M here: the
401 module will be called goodix.
402
403config TOUCHSCREEN_HIDEEP
404 tristate "HiDeep Touch IC"
405 depends on I2C
406 help
407 Say Y here if you have a touchscreen using HiDeep.
408
409 If unsure, say N.
410
411 To compile this driver as a module, choose M here : the
412 module will be called hideep_ts.
413
414config TOUCHSCREEN_HYCON_HY46XX
415 tristate "Hycon hy46xx touchscreen support"
416 depends on I2C
417 help
418 Say Y here if you have a touchscreen using Hycon hy46xx
419
420 If unsure, say N.
421
422 To compile this driver as a module, choose M here: the
423 module will be called hycon-hy46xx.
424
425config TOUCHSCREEN_ILI210X
426 tristate "Ilitek ILI210X based touchscreen"
427 depends on I2C
428 help
429 Say Y here if you have a ILI210X based touchscreen
430 controller. This driver supports models ILI2102,
431 ILI2102s, ILI2103, ILI2103s and ILI2105.
432 Such kind of chipsets can be found in Amazon Kindle Fire
433 touchscreens.
434
435 If unsure, say N.
436
437 To compile this driver as a module, choose M here: the
438 module will be called ili210x.
439
440config TOUCHSCREEN_ILITEK
441 tristate "Ilitek I2C 213X/23XX/25XX/Lego Series Touch ICs"
442 depends on I2C
443 help
444 Say Y here if you have touchscreen with ILITEK touch IC,
445 it supports 213X/23XX/25XX and other Lego series.
446
447 If unsure, say N.
448
449 To compile this driver as a module, choose M here: the
450 module will be called ilitek_ts_i2c.
451
452config TOUCHSCREEN_IPROC
453 tristate "IPROC touch panel driver support"
454 depends on ARCH_BCM_IPROC || COMPILE_TEST
455 help
456 Say Y here if you want to add support for the IPROC touch
457 controller to your system.
458
459 If unsure, say N.
460
461 To compile this driver as a module, choose M here: the
462 module will be called bcm_iproc_tsc.
463
464config TOUCHSCREEN_S3C2410
465 tristate "Samsung S3C2410/generic touchscreen input driver"
466 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
467 depends on S3C_ADC
468 help
469 Say Y here if you have the s3c2410 touchscreen.
470
471 If unsure, say N.
472
473 To compile this driver as a module, choose M here: the
474 module will be called s3c2410_ts.
475
476config TOUCHSCREEN_S6SY761
477 tristate "Samsung S6SY761 Touchscreen driver"
478 depends on I2C
479 help
480 Say Y if you have the Samsung S6SY761 driver
481
482 If unsure, say N
483
484 To compile this driver as module, choose M here: the
485 module will be called s6sy761.
486
487config TOUCHSCREEN_GUNZE
488 tristate "Gunze AHL-51S touchscreen"
489 select SERIO
490 help
491 Say Y here if you have the Gunze AHL-51 touchscreen connected to
492 your system.
493
494 If unsure, say N.
495
496 To compile this driver as a module, choose M here: the
497 module will be called gunze.
498
499config TOUCHSCREEN_EKTF2127
500 tristate "Elan eKTF2127 I2C touchscreen"
501 depends on I2C
502 help
503 Say Y here if you have an Elan eKTF2127 touchscreen
504 connected to your system.
505
506 If unsure, say N.
507
508 To compile this driver as a module, choose M here: the
509 module will be called ektf2127.
510
511config TOUCHSCREEN_ELAN
512 tristate "Elan eKTH I2C touchscreen"
513 depends on I2C
514 help
515 Say Y here if you have an Elan eKTH I2C touchscreen
516 connected to your system.
517
518 If unsure, say N.
519
520 To compile this driver as a module, choose M here: the
521 module will be called elants_i2c.
522
523config TOUCHSCREEN_ELO
524 tristate "Elo serial touchscreens"
525 select SERIO
526 help
527 Say Y here if you have an Elo serial touchscreen connected to
528 your system.
529
530 If unsure, say N.
531
532 To compile this driver as a module, choose M here: the
533 module will be called elo.
534
535config TOUCHSCREEN_WACOM_W8001
536 tristate "Wacom W8001 penabled serial touchscreen"
537 select SERIO
538 help
539 Say Y here if you have an Wacom W8001 penabled serial touchscreen
540 connected to your system.
541
542 If unsure, say N.
543
544 To compile this driver as a module, choose M here: the
545 module will be called wacom_w8001.
546
547config TOUCHSCREEN_WACOM_I2C
548 tristate "Wacom Tablet support (I2C)"
549 depends on I2C
550 help
551 Say Y here if you want to use the I2C version of the Wacom
552 Pen Tablet.
553
554 If unsure, say N.
555
556 To compile this driver as a module, choose M here: the module
557 will be called wacom_i2c.
558
559config TOUCHSCREEN_LPC32XX
560 tristate "LPC32XX touchscreen controller"
561 depends on ARCH_LPC32XX
562 help
563 Say Y here if you have a LPC32XX device and want
564 to support the built-in touchscreen.
565
566 To compile this driver as a module, choose M here: the
567 module will be called lpc32xx_ts.
568
569config TOUCHSCREEN_MAX11801
570 tristate "MAX11801 based touchscreens"
571 depends on I2C
572 help
573 Say Y here if you have a MAX11801 based touchscreen
574 controller.
575
576 If unsure, say N.
577
578 To compile this driver as a module, choose M here: the
579 module will be called max11801_ts.
580
581config TOUCHSCREEN_MCS5000
582 tristate "MELFAS MCS-5000 touchscreen"
583 depends on I2C
584 help
585 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
586 chip in your system.
587
588 If unsure, say N.
589
590 To compile this driver as a module, choose M here: the
591 module will be called mcs5000_ts.
592
593config TOUCHSCREEN_MMS114
594 tristate "MELFAS MMS114 touchscreen"
595 depends on I2C
596 help
597 Say Y here if you have the MELFAS MMS114 touchscreen controller
598 chip in your system.
599
600 If unsure, say N.
601
602 To compile this driver as a module, choose M here: the
603 module will be called mms114.
604
605config TOUCHSCREEN_MELFAS_MIP4
606 tristate "MELFAS MIP4 Touchscreen"
607 depends on I2C
608 help
609 Say Y here if you have a MELFAS MIP4 Touchscreen device.
610
611 If unsure, say N.
612
613 To compile this driver as a module, choose M here:
614 the module will be called melfas_mip4.
615
616config TOUCHSCREEN_MSG2638
617 tristate "MStar msg2638 touchscreen support"
618 depends on I2C
619 depends on GPIOLIB || COMPILE_TEST
620 help
621 Say Y here if you have an I2C touchscreen using MStar msg2638.
622
623 If unsure, say N.
624
625 To compile this driver as a module, choose M here: the
626 module will be called msg2638.
627
628config TOUCHSCREEN_MTOUCH
629 tristate "MicroTouch serial touchscreens"
630 select SERIO
631 help
632 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
633 your system.
634
635 If unsure, say N.
636
637 To compile this driver as a module, choose M here: the
638 module will be called mtouch.
639
640config TOUCHSCREEN_IMX6UL_TSC
641 tristate "Freescale i.MX6UL touchscreen controller"
642 depends on ((OF && GPIOLIB) || COMPILE_TEST) && HAS_IOMEM
643 help
644 Say Y here if you have a Freescale i.MX6UL, and want to
645 use the internal touchscreen controller.
646
647 If unsure, say N.
648
649 To compile this driver as a module, choose M here: the
650 module will be called imx6ul_tsc.
651
652config TOUCHSCREEN_INEXIO
653 tristate "iNexio serial touchscreens"
654 select SERIO
655 help
656 Say Y here if you have an iNexio serial touchscreen connected to
657 your system.
658
659 If unsure, say N.
660
661 To compile this driver as a module, choose M here: the
662 module will be called inexio.
663
664config TOUCHSCREEN_MK712
665 tristate "ICS MicroClock MK712 touchscreen"
666 help
667 Say Y here if you have the ICS MicroClock MK712 touchscreen
668 controller chip in your system.
669
670 If unsure, say N.
671
672 To compile this driver as a module, choose M here: the
673 module will be called mk712.
674
675config TOUCHSCREEN_HP600
676 tristate "HP Jornada 6xx touchscreen"
677 depends on SH_HP6XX && SH_ADC
678 help
679 Say Y here if you have a HP Jornada 620/660/680/690 and want to
680 support the built-in touchscreen.
681
682 To compile this driver as a module, choose M here: the
683 module will be called hp680_ts_input.
684
685config TOUCHSCREEN_HP7XX
686 tristate "HP Jornada 7xx touchscreen"
687 depends on SA1100_JORNADA720_SSP
688 help
689 Say Y here if you have a HP Jornada 710/720/728 and want
690 to support the built-in touchscreen.
691
692 To compile this driver as a module, choose M here: the
693 module will be called jornada720_ts.
694
695config TOUCHSCREEN_IPAQ_MICRO
696 tristate "HP iPAQ Atmel Micro ASIC touchscreen"
697 depends on MFD_IPAQ_MICRO
698 help
699 Say Y here to enable support for the touchscreen attached to
700 the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
701
702 If unsure, say N.
703
704 To compile this driver as a module, choose M here: the
705 module will be called ipaq-micro-ts.
706
707config TOUCHSCREEN_HTCPEN
708 tristate "HTC Shift X9500 touchscreen"
709 depends on ISA
710 help
711 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
712 Clio / Shangrila and want to support the built-in touchscreen.
713
714 If unsure, say N.
715
716 To compile this driver as a module, choose M here: the
717 module will be called htcpen.
718
719config TOUCHSCREEN_PENMOUNT
720 tristate "Penmount serial touchscreen"
721 select SERIO
722 help
723 Say Y here if you have a Penmount serial touchscreen connected to
724 your system.
725
726 If unsure, say N.
727
728 To compile this driver as a module, choose M here: the
729 module will be called penmount.
730
731config TOUCHSCREEN_EDT_FT5X06
732 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
733 depends on I2C
734 help
735 Say Y here if you have an EDT "Polytouch" touchscreen based
736 on the FocalTech FT5x06 family of controllers connected to
737 your system.
738
739 If unsure, say N.
740
741 To compile this driver as a module, choose M here: the
742 module will be called edt-ft5x06.
743
744config TOUCHSCREEN_RASPBERRYPI_FW
745 tristate "Raspberry Pi's firmware base touch screen support"
746 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
747 help
748 Say Y here if you have the official Raspberry Pi 7 inch screen on
749 your system.
750
751 If unsure, say N.
752
753 To compile this driver as a module, choose M here: the
754 module will be called raspberrypi-ts.
755
756config TOUCHSCREEN_MIGOR
757 tristate "Renesas MIGO-R touchscreen"
758 depends on (SH_MIGOR || COMPILE_TEST) && I2C
759 help
760 Say Y here to enable MIGO-R touchscreen support.
761
762 If unsure, say N.
763
764 To compile this driver as a module, choose M here: the
765 module will be called migor_ts.
766
767config TOUCHSCREEN_TOUCHRIGHT
768 tristate "Touchright serial touchscreen"
769 select SERIO
770 help
771 Say Y here if you have a Touchright serial touchscreen connected to
772 your system.
773
774 If unsure, say N.
775
776 To compile this driver as a module, choose M here: the
777 module will be called touchright.
778
779config TOUCHSCREEN_TOUCHWIN
780 tristate "Touchwin serial touchscreen"
781 select SERIO
782 help
783 Say Y here if you have a Touchwin serial touchscreen connected to
784 your system.
785
786 If unsure, say N.
787
788 To compile this driver as a module, choose M here: the
789 module will be called touchwin.
790
791config TOUCHSCREEN_TI_AM335X_TSC
792 tristate "TI Touchscreen Interface"
793 depends on MFD_TI_AM335X_TSCADC
794 help
795 Say Y here if you have 4/5/8 wire touchscreen controller
796 to be connected to the ADC controller on your TI AM335x SoC.
797
798 If unsure, say N.
799
800 To compile this driver as a module, choose M here: the
801 module will be called ti_am335x_tsc.
802
803config TOUCHSCREEN_UCB1400
804 tristate "Philips UCB1400 touchscreen"
805 depends on AC97_BUS
806 depends on UCB1400_CORE
807 help
808 This enables support for the Philips UCB1400 touchscreen interface.
809 The UCB1400 is an AC97 audio codec. The touchscreen interface
810 will be initialized only after the ALSA subsystem has been
811 brought up and the UCB1400 detected. You therefore have to
812 configure ALSA support as well (either built-in or modular,
813 independently of whether this driver is itself built-in or
814 modular) for this driver to work.
815
816 To compile this driver as a module, choose M here: the
817 module will be called ucb1400_ts.
818
819config TOUCHSCREEN_PIXCIR
820 tristate "PIXCIR I2C touchscreens"
821 depends on I2C
822 help
823 Say Y here if you have a pixcir i2c touchscreen
824 controller.
825
826 If unsure, say N.
827
828 To compile this driver as a module, choose M here: the
829 module will be called pixcir_i2c_ts.
830
831config TOUCHSCREEN_WDT87XX_I2C
832 tristate "Weida HiTech I2C touchscreen"
833 depends on I2C
834 help
835 Say Y here if you have a Weida WDT87XX I2C touchscreen
836 connected to your system.
837
838 If unsure, say N.
839
840 To compile this driver as a module, choose M here: the
841 module will be called wdt87xx_i2c.
842
843config TOUCHSCREEN_WM831X
844 tristate "Support for WM831x touchscreen controllers"
845 depends on MFD_WM831X
846 help
847 This enables support for the touchscreen controller on the WM831x
848 series of PMICs.
849
850 To compile this driver as a module, choose M here: the
851 module will be called wm831x-ts.
852
853config TOUCHSCREEN_WM97XX
854 tristate "Support for WM97xx AC97 touchscreen controllers"
855 depends on AC97_BUS || AC97_BUS_NEW
856 help
857 Say Y here if you have a Wolfson Microelectronics WM97xx
858 touchscreen connected to your system. Note that this option
859 only enables core driver, you will also need to select
860 support for appropriate chip below.
861
862 If unsure, say N.
863
864 To compile this driver as a module, choose M here: the
865 module will be called wm97xx-ts.
866
867config TOUCHSCREEN_WM9705
868 bool "WM9705 Touchscreen interface support"
869 depends on TOUCHSCREEN_WM97XX
870 default y
871 help
872 Say Y here to enable support for the Wolfson Microelectronics
873 WM9705 touchscreen controller.
874
875config TOUCHSCREEN_WM9712
876 bool "WM9712 Touchscreen interface support"
877 depends on TOUCHSCREEN_WM97XX
878 default y
879 help
880 Say Y here to enable support for the Wolfson Microelectronics
881 WM9712 touchscreen controller.
882
883config TOUCHSCREEN_WM9713
884 bool "WM9713 Touchscreen interface support"
885 depends on TOUCHSCREEN_WM97XX
886 default y
887 help
888 Say Y here to enable support for the Wolfson Microelectronics
889 WM9713 touchscreen controller.
890
891config TOUCHSCREEN_WM97XX_MAINSTONE
892 tristate "WM97xx Mainstone/Palm accelerated touch"
893 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
894 help
895 Say Y here for support for streaming mode with WM97xx touchscreens
896 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
897
898 If unsure, say N.
899
900 To compile this driver as a module, choose M here: the
901 module will be called mainstone-wm97xx.
902
903config TOUCHSCREEN_WM97XX_ZYLONITE
904 tristate "Zylonite accelerated touch"
905 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
906 select TOUCHSCREEN_WM9713
907 help
908 Say Y here for support for streaming mode with the touchscreen
909 on Zylonite systems.
910
911 If unsure, say N.
912
913 To compile this driver as a module, choose M here: the
914 module will be called zylonite-wm97xx.
915
916config TOUCHSCREEN_USB_COMPOSITE
917 tristate "USB Touchscreen Driver"
918 depends on USB_ARCH_HAS_HCD
919 select USB
920 help
921 USB Touchscreen driver for:
922 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
923 - PanJit TouchSet USB
924 - 3M MicroTouch USB (EX II series)
925 - ITM
926 - some other eTurboTouch
927 - Gunze AHL61
928 - DMC TSC-10/25
929 - IRTOUCHSYSTEMS/UNITOP
930 - IdealTEK URTC1000
931 - GoTop Super_Q2/GogoPen/PenPower tablets
932 - JASTEC USB Touch Controller/DigiTech DTR-02U
933 - Zytronic controllers
934 - Elo TouchSystems 2700 IntelliTouch
935 - EasyTouch USB Touch Controller from Data Modul
936 - e2i (Mimo monitors)
937
938 Have a look at <http://linux.chapter7.ch/touchkit/> for
939 a usage description and the required user-space stuff.
940
941 To compile this driver as a module, choose M here: the
942 module will be called usbtouchscreen.
943
944config TOUCHSCREEN_MXS_LRADC
945 tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
946 depends on MFD_MXS_LRADC
947 help
948 Say Y here if you have a touchscreen connected to the low-resolution
949 analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
950
951 To compile this driver as a module, choose M here: the module will be
952 called mxs-lradc-ts.
953
954config TOUCHSCREEN_MX25
955 tristate "Freescale i.MX25 touchscreen input driver"
956 depends on MFD_MX25_TSADC
957 help
958 Enable support for touchscreen connected to your i.MX25.
959
960 To compile this driver as a module, choose M here: the
961 module will be called fsl-imx25-tcq.
962
963config TOUCHSCREEN_MC13783
964 tristate "Freescale MC13783 touchscreen input driver"
965 depends on MFD_MC13XXX
966 help
967 Say Y here if you have an Freescale MC13783 PMIC on your
968 board and want to use its touchscreen
969
970 If unsure, say N.
971
972 To compile this driver as a module, choose M here: the
973 module will be called mc13783_ts.
974
975config TOUCHSCREEN_USB_EGALAX
976 default y
977 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
978 depends on TOUCHSCREEN_USB_COMPOSITE
979
980config TOUCHSCREEN_USB_PANJIT
981 default y
982 bool "PanJit device support" if EXPERT
983 depends on TOUCHSCREEN_USB_COMPOSITE
984
985config TOUCHSCREEN_USB_3M
986 default y
987 bool "3M/Microtouch EX II series device support" if EXPERT
988 depends on TOUCHSCREEN_USB_COMPOSITE
989
990config TOUCHSCREEN_USB_ITM
991 default y
992 bool "ITM device support" if EXPERT
993 depends on TOUCHSCREEN_USB_COMPOSITE
994
995config TOUCHSCREEN_USB_ETURBO
996 default y
997 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
998 depends on TOUCHSCREEN_USB_COMPOSITE
999
1000config TOUCHSCREEN_USB_GUNZE
1001 default y
1002 bool "Gunze AHL61 device support" if EXPERT
1003 depends on TOUCHSCREEN_USB_COMPOSITE
1004
1005config TOUCHSCREEN_USB_DMC_TSC10
1006 default y
1007 bool "DMC TSC-10/25 device support" if EXPERT
1008 depends on TOUCHSCREEN_USB_COMPOSITE
1009
1010config TOUCHSCREEN_USB_IRTOUCH
1011 default y
1012 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
1013 depends on TOUCHSCREEN_USB_COMPOSITE
1014
1015config TOUCHSCREEN_USB_IDEALTEK
1016 default y
1017 bool "IdealTEK URTC1000 device support" if EXPERT
1018 depends on TOUCHSCREEN_USB_COMPOSITE
1019
1020config TOUCHSCREEN_USB_GENERAL_TOUCH
1021 default y
1022 bool "GeneralTouch Touchscreen device support" if EXPERT
1023 depends on TOUCHSCREEN_USB_COMPOSITE
1024
1025config TOUCHSCREEN_USB_GOTOP
1026 default y
1027 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
1028 depends on TOUCHSCREEN_USB_COMPOSITE
1029
1030config TOUCHSCREEN_USB_JASTEC
1031 default y
1032 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
1033 depends on TOUCHSCREEN_USB_COMPOSITE
1034
1035config TOUCHSCREEN_USB_ELO
1036 default y
1037 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
1038 depends on TOUCHSCREEN_USB_COMPOSITE
1039
1040config TOUCHSCREEN_USB_E2I
1041 default y
1042 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
1043 depends on TOUCHSCREEN_USB_COMPOSITE
1044
1045config TOUCHSCREEN_USB_ZYTRONIC
1046 default y
1047 bool "Zytronic controller" if EXPERT
1048 depends on TOUCHSCREEN_USB_COMPOSITE
1049
1050config TOUCHSCREEN_USB_ETT_TC45USB
1051 default y
1052 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
1053 depends on TOUCHSCREEN_USB_COMPOSITE
1054
1055config TOUCHSCREEN_USB_NEXIO
1056 default y
1057 bool "NEXIO/iNexio device support" if EXPERT
1058 depends on TOUCHSCREEN_USB_COMPOSITE
1059
1060config TOUCHSCREEN_USB_EASYTOUCH
1061 default y
1062 bool "EasyTouch USB Touch controller device support" if EXPERT
1063 depends on TOUCHSCREEN_USB_COMPOSITE
1064 help
1065 Say Y here if you have an EasyTouch USB Touch controller.
1066 If unsure, say N.
1067
1068config TOUCHSCREEN_TOUCHIT213
1069 tristate "Sahara TouchIT-213 touchscreen"
1070 select SERIO
1071 help
1072 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
1073
1074 If unsure, say N.
1075
1076 To compile this driver as a module, choose M here: the
1077 module will be called touchit213.
1078
1079config TOUCHSCREEN_TS4800
1080 tristate "TS-4800 touchscreen"
1081 depends on HAS_IOMEM && OF
1082 depends on SOC_IMX51 || COMPILE_TEST
1083 select MFD_SYSCON
1084 help
1085 Say Y here if you have a touchscreen on a TS-4800 board.
1086
1087 On TS-4800, the touchscreen is not handled directly by Linux but by
1088 a companion FPGA.
1089
1090 If unsure, say N.
1091
1092 To compile this driver as a module, choose M here: the
1093 module will be called ts4800_ts.
1094
1095config TOUCHSCREEN_TSC_SERIO
1096 tristate "TSC-10/25/40 serial touchscreen support"
1097 select SERIO
1098 help
1099 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
1100 to your system.
1101
1102 If unsure, say N.
1103
1104 To compile this driver as a module, choose M here: the
1105 module will be called tsc40.
1106
1107config TOUCHSCREEN_TSC200X_CORE
1108 tristate
1109
1110config TOUCHSCREEN_TSC2004
1111 tristate "TSC2004 based touchscreens"
1112 depends on I2C
1113 select REGMAP_I2C
1114 select TOUCHSCREEN_TSC200X_CORE
1115 help
1116 Say Y here if you have a TSC2004 based touchscreen.
1117
1118 If unsure, say N.
1119
1120 To compile this driver as a module, choose M here: the
1121 module will be called tsc2004.
1122
1123config TOUCHSCREEN_TSC2005
1124 tristate "TSC2005 based touchscreens"
1125 depends on SPI_MASTER
1126 select REGMAP_SPI
1127 select TOUCHSCREEN_TSC200X_CORE
1128 help
1129 Say Y here if you have a TSC2005 based touchscreen.
1130
1131 If unsure, say N.
1132
1133 To compile this driver as a module, choose M here: the
1134 module will be called tsc2005.
1135
1136config TOUCHSCREEN_TSC2007
1137 tristate "TSC2007 based touchscreens"
1138 depends on I2C
1139 help
1140 Say Y here if you have a TSC2007 based touchscreen.
1141
1142 If unsure, say N.
1143
1144 To compile this driver as a module, choose M here: the
1145 module will be called tsc2007.
1146
1147config TOUCHSCREEN_TSC2007_IIO
1148 bool "IIO interface for external ADC input and temperature"
1149 depends on TOUCHSCREEN_TSC2007
1150 depends on IIO=y || IIO=TOUCHSCREEN_TSC2007
1151 help
1152 Saying Y here adds an iio interface to the tsc2007 which
1153 provides values for the AUX input (used for e.g. battery
1154 or ambient light monitoring), temperature and raw input
1155 values.
1156
1157config TOUCHSCREEN_PCAP
1158 tristate "Motorola PCAP touchscreen"
1159 depends on EZX_PCAP
1160 help
1161 Say Y here if you have a Motorola EZX telephone and
1162 want to enable support for the built-in touchscreen.
1163
1164 To compile this driver as a module, choose M here: the
1165 module will be called pcap_ts.
1166
1167config TOUCHSCREEN_RM_TS
1168 tristate "Raydium I2C Touchscreen"
1169 depends on I2C
1170 depends on GPIOLIB || COMPILE_TEST
1171 help
1172 Say Y here if you have Raydium series I2C touchscreen,
1173 such as RM32380, connected to your system.
1174
1175 If unsure, say N.
1176
1177 To compile this driver as a module, choose M here: the
1178 module will be called raydium_i2c_ts.
1179
1180config TOUCHSCREEN_SILEAD
1181 tristate "Silead I2C touchscreen"
1182 depends on I2C
1183 help
1184 Say Y here if you have the Silead touchscreen connected to
1185 your system.
1186
1187 If unsure, say N.
1188
1189 To compile this driver as a module, choose M here: the
1190 module will be called silead.
1191
1192config TOUCHSCREEN_SIS_I2C
1193 tristate "SiS 9200 family I2C touchscreen"
1194 depends on I2C
1195 select CRC_ITU_T
1196 depends on GPIOLIB || COMPILE_TEST
1197 help
1198 This enables support for SiS 9200 family over I2C based touchscreens.
1199
1200 If unsure, say N.
1201
1202 To compile this driver as a module, choose M here: the
1203 module will be called sis_i2c.
1204
1205config TOUCHSCREEN_ST1232
1206 tristate "Sitronix ST1232 or ST1633 touchscreen controllers"
1207 depends on I2C
1208 help
1209 Say Y here if you want to support the Sitronix ST1232
1210 or ST1633 touchscreen controller.
1211
1212 If unsure, say N.
1213
1214 To compile this driver as a module, choose M here: the
1215 module will be called st1232_ts.
1216
1217config TOUCHSCREEN_STMFTS
1218 tristate "STMicroelectronics STMFTS touchscreen"
1219 depends on I2C
1220 depends on LEDS_CLASS
1221 help
1222 Say Y here if you want support for STMicroelectronics
1223 STMFTS touchscreen.
1224
1225 To compile this driver as a module, choose M here: the
1226 module will be called stmfts.
1227
1228config TOUCHSCREEN_STMPE
1229 tristate "STMicroelectronics STMPE touchscreens"
1230 depends on MFD_STMPE
1231 depends on (OF || COMPILE_TEST)
1232 help
1233 Say Y here if you want support for STMicroelectronics
1234 STMPE touchscreen controllers.
1235
1236 To compile this driver as a module, choose M here: the
1237 module will be called stmpe-ts.
1238
1239config TOUCHSCREEN_SUN4I
1240 tristate "Allwinner sun4i resistive touchscreen controller support"
1241 depends on ARCH_SUNXI || COMPILE_TEST
1242 depends on HWMON
1243 depends on THERMAL || !THERMAL_OF
1244 help
1245 This selects support for the resistive touchscreen controller
1246 found on Allwinner sunxi SoCs.
1247
1248 To compile this driver as a module, choose M here: the
1249 module will be called sun4i-ts.
1250
1251config TOUCHSCREEN_SUR40
1252 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
1253 depends on USB && MEDIA_USB_SUPPORT && HAS_DMA
1254 depends on VIDEO_V4L2
1255 select VIDEOBUF2_DMA_SG
1256 help
1257 Say Y here if you want support for the Samsung SUR40 touchscreen
1258 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
1259
1260 To compile this driver as a module, choose M here: the
1261 module will be called sur40.
1262
1263config TOUCHSCREEN_SURFACE3_SPI
1264 tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
1265 depends on SPI
1266 depends on GPIOLIB || COMPILE_TEST
1267 help
1268 Say Y here if you have the Ntrig/Microsoft SPI touchscreen
1269 controller chip as found on the Surface 3 in your system.
1270
1271 If unsure, say N.
1272
1273 To compile this driver as a module, choose M here: the
1274 module will be called surface3_spi.
1275
1276config TOUCHSCREEN_SX8654
1277 tristate "Semtech SX8654 touchscreen"
1278 depends on I2C
1279 help
1280 Say Y here if you have a Semtech SX8654 touchscreen controller.
1281
1282 If unsure, say N
1283
1284 To compile this driver as a module, choose M here: the
1285 module will be called sx8654.
1286
1287config TOUCHSCREEN_TPS6507X
1288 tristate "TPS6507x based touchscreens"
1289 depends on I2C
1290 help
1291 Say Y here if you have a TPS6507x based touchscreen
1292 controller.
1293
1294 If unsure, say N.
1295
1296 To compile this driver as a module, choose M here: the
1297 module will be called tps6507x_ts.
1298
1299config TOUCHSCREEN_ZET6223
1300 tristate "Zeitec ZET6223 touchscreen driver"
1301 depends on I2C
1302 help
1303 Say Y here if you have a touchscreen using Zeitec ZET6223
1304
1305 If unsure, say N.
1306
1307 To compile this driver as a module, choose M here: the
1308 module will be called zet6223.
1309
1310config TOUCHSCREEN_ZFORCE
1311 tristate "Neonode zForce infrared touchscreens"
1312 depends on I2C
1313 depends on GPIOLIB || COMPILE_TEST
1314 help
1315 Say Y here if you have a touchscreen using the zforce
1316 infraread technology from Neonode.
1317
1318 If unsure, say N.
1319
1320 To compile this driver as a module, choose M here: the
1321 module will be called zforce_ts.
1322
1323config TOUCHSCREEN_COLIBRI_VF50
1324 tristate "Toradex Colibri on board touchscreen driver"
1325 depends on IIO && VF610_ADC
1326 depends on GPIOLIB || COMPILE_TEST
1327 help
1328 Say Y here if you have a Colibri VF50 and plan to use
1329 the on-board provided 4-wire touchscreen driver.
1330
1331 If unsure, say N.
1332
1333 To compile this driver as a module, choose M here: the
1334 module will be called colibri_vf50_ts.
1335
1336config TOUCHSCREEN_ROHM_BU21023
1337 tristate "ROHM BU21023/24 Dual touch support resistive touchscreens"
1338 depends on I2C
1339 help
1340 Say Y here if you have a touchscreen using ROHM BU21023/24.
1341
1342 If unsure, say N.
1343
1344 To compile this driver as a module, choose M here: the
1345 module will be called bu21023_ts.
1346
1347config TOUCHSCREEN_IQS5XX
1348 tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
1349 depends on I2C
1350 help
1351 Say Y to enable support for the Azoteq IQS550/572/525
1352 family of trackpad/touchscreen controllers.
1353
1354 To compile this driver as a module, choose M here: the
1355 module will be called iqs5xx.
1356
1357config TOUCHSCREEN_ZINITIX
1358 tristate "Zinitix touchscreen support"
1359 depends on I2C
1360 help
1361 Say Y here if you have a touchscreen using Zinitix bt541,
1362 or something similar enough.
1363
1364 If unsure, say N.
1365
1366 To compile this driver as a module, choose M here: the
1367 module will be called zinitix.
1368
1369endif