Loading...
1# SPDX-License-Identifier: GPL-2.0
2#
3# USB Miscellaneous driver configuration
4#
5comment "USB Miscellaneous drivers"
6
7config USB_USS720
8 tristate "USS720 parport driver"
9 depends on PARPORT
10 select PARPORT_NOT_PC
11 help
12 This driver is for USB parallel port adapters that use the Lucent
13 Technologies USS-720 chip. These cables are plugged into your USB
14 port and provide USB compatibility to peripherals designed with
15 parallel port interfaces.
16
17 The chip has two modes: automatic mode and manual mode. In automatic
18 mode, it looks to the computer like a standard USB printer. Only
19 printers may be connected to the USS-720 in this mode. The generic
20 USB printer driver ("USB Printer support", above) may be used in
21 that mode, and you can say N here if you want to use the chip only
22 in this mode.
23
24 Manual mode is not limited to printers, any parallel port
25 device should work. This driver utilizes manual mode.
26 Note however that some operations are three orders of magnitude
27 slower than on a PCI/ISA Parallel Port, so timing critical
28 applications might not work.
29
30 Say Y here if you own an USS-720 USB->Parport cable and intend to
31 connect anything other than a printer to it.
32
33 To compile this driver as a module, choose M here: the
34 module will be called uss720.
35
36config USB_EMI62
37 tristate "EMI 6|2m USB Audio interface support"
38 help
39 This driver loads firmware to Emagic EMI 6|2m low latency USB
40 Audio and Midi interface.
41
42 After firmware load the device is handled with standard linux
43 USB Audio driver.
44
45 This code is also available as a module ( = code which can be
46 inserted in and removed from the running kernel whenever you want).
47 The module will be called audio. If you want to compile it as a
48 module, say M here and read <file:Documentation/kbuild/modules.rst>.
49
50config USB_EMI26
51 tristate "EMI 2|6 USB Audio interface support"
52 help
53 This driver loads firmware to Emagic EMI 2|6 low latency USB
54 Audio interface.
55
56 After firmware load the device is handled with standard linux
57 USB Audio driver.
58
59 To compile this driver as a module, choose M here: the
60 module will be called emi26.
61
62config USB_ADUTUX
63 tristate "ADU devices from Ontrak Control Systems"
64 help
65 Say Y if you want to use an ADU device from Ontrak Control
66 Systems.
67
68 To compile this driver as a module, choose M here. The module
69 will be called adutux.
70
71config USB_SEVSEG
72 tristate "USB 7-Segment LED Display"
73 help
74 Say Y here if you have a USB 7-Segment Display by Delcom
75
76 To compile this driver as a module, choose M here: the
77 module will be called usbsevseg.
78
79config USB_LEGOTOWER
80 tristate "USB Lego Infrared Tower support"
81 help
82 Say Y here if you want to connect a USB Lego Infrared Tower to your
83 computer's USB port.
84
85 This code is also available as a module ( = code which can be
86 inserted in and removed from the running kernel whenever you want).
87 The module will be called legousbtower. If you want to compile it as
88 a module, say M here and read
89 <file:Documentation/kbuild/modules.rst>.
90
91config USB_LCD
92 tristate "USB LCD driver support"
93 help
94 Say Y here if you want to connect an USBLCD to your computer's
95 USB port. The USBLCD is a small USB interface board for
96 alphanumeric LCD modules. See <http://www.usblcd.de/> for more
97 information.
98
99 To compile this driver as a module, choose M here: the
100 module will be called usblcd.
101
102config USB_CYPRESS_CY7C63
103 tristate "Cypress CY7C63xxx USB driver support"
104 help
105 Say Y here if you want to connect a Cypress CY7C63xxx
106 micro controller to your computer's USB port. Currently this
107 driver supports the pre-programmed devices (incl. firmware)
108 by AK Modul-Bus Computer GmbH.
109
110 Please see: https://www.ak-modul-bus.de/stat/mikrocontroller.html
111
112 To compile this driver as a module, choose M here: the
113 module will be called cypress_cy7c63.
114
115config USB_CYTHERM
116 tristate "Cypress USB thermometer driver support"
117 help
118 Say Y here if you want to connect a Cypress USB thermometer
119 device to your computer's USB port. This device is also known
120 as the Cypress USB Starter kit or demo board. The Elektor
121 magazine published a modified version of this device in issue
122 #291.
123
124 To compile this driver as a module, choose M here: the
125 module will be called cytherm.
126
127config USB_IDMOUSE
128 tristate "Siemens ID USB Mouse Fingerprint sensor support"
129 help
130 Say Y here if you want to use the fingerprint sensor on
131 the Siemens ID Mouse. There is also a Siemens ID Mouse
132 _Professional_, which has not been tested with this driver,
133 but uses the same sensor and may therefore work.
134
135 This driver creates an entry "/dev/idmouseX" or "/dev/usb/idmouseX",
136 which can be used by, e.g.,"cat /dev/idmouse0 > fingerprint.pnm".
137
138 See also <https://www.fs.tum.de/~echtler/idmouse/>.
139
140config USB_APPLEDISPLAY
141 tristate "Apple Cinema Display support"
142 select BACKLIGHT_CLASS_DEVICE
143 help
144 Say Y here if you want to control the backlight of Apple Cinema
145 Displays over USB. This driver provides a sysfs interface.
146
147config USB_QCOM_EUD
148 tristate "QCOM Embedded USB Debugger(EUD) Driver"
149 depends on ARCH_QCOM || COMPILE_TEST
150 select USB_ROLE_SWITCH
151 help
152 This module enables support for Qualcomm Technologies, Inc.
153 Embedded USB Debugger (EUD). The EUD is a control peripheral
154 which reports VBUS attach/detach events and has USB-based
155 debug and trace capabilities. On selecting m, the module name
156 that is built is qcom_eud.ko
157
158config APPLE_MFI_FASTCHARGE
159 tristate "Fast charge control for iOS devices"
160 select POWER_SUPPLY
161 help
162 Say Y here if you want to control whether iOS devices will
163 fast charge from the USB interface, as implemented in "MFi"
164 chargers.
165
166 It is safe to say M here.
167
168config USB_LJCA
169 tristate "Intel La Jolla Cove Adapter support"
170 select AUXILIARY_BUS
171 depends on USB && ACPI
172 help
173 This adds support for Intel La Jolla Cove USB-I2C/SPI/GPIO
174 Master Adapter (LJCA). Additional drivers such as I2C_LJCA,
175 GPIO_LJCA and SPI_LJCA must be enabled in order to use the
176 functionality of the device.
177
178 This driver can also be built as a module. If so, the module
179 will be called usb-ljca.
180
181source "drivers/usb/misc/sisusbvga/Kconfig"
182
183config USB_LD
184 tristate "USB LD driver"
185 help
186 This driver is for generic USB devices that use interrupt transfers,
187 like LD Didactic's USB devices.
188
189 To compile this driver as a module, choose M here: the
190 module will be called ldusb.
191
192config USB_TRANCEVIBRATOR
193 tristate "PlayStation 2 Trance Vibrator driver support"
194 help
195 Say Y here if you want to connect a PlayStation 2 Trance Vibrator
196 device to your computer's USB port.
197
198 To compile this driver as a module, choose M here: the
199 module will be called trancevibrator.
200
201config USB_IOWARRIOR
202 tristate "IO Warrior driver support"
203 help
204 Say Y here if you want to support the IO Warrior devices from Code
205 Mercenaries. This includes support for the following devices:
206 IO Warrior 40
207 IO Warrior 24
208 IO Warrior 56
209 IO Warrior 24 Power Vampire
210
211 To compile this driver as a module, choose M here: the
212 module will be called iowarrior.
213
214config USB_TEST
215 tristate "USB testing driver"
216 help
217 This driver is for testing host controller software. It is used
218 with specialized device firmware for regression and stress testing,
219 to help prevent problems from cropping up with "real" drivers.
220
221 See <http://www.linux-usb.org/usbtest/> for more information,
222 including sample test device firmware and "how to use it".
223
224config USB_EHSET_TEST_FIXTURE
225 tristate "USB EHSET Test Fixture driver"
226 help
227 Say Y here if you want to support the special test fixture device
228 used for the USB-IF Embedded Host High-Speed Electrical Test procedure.
229
230 When the test fixture is connected, it can enumerate as one of several
231 VID/PID pairs. This driver then initiates a corresponding test mode on
232 the downstream port to which the test fixture is attached.
233
234 See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more
235 information.
236
237config USB_ISIGHTFW
238 tristate "iSight firmware loading support"
239 select FW_LOADER
240 help
241 This driver loads firmware for USB Apple iSight cameras, allowing
242 them to be driven by the USB video class driver available at
243 http://linux-uvc.berlios.de
244
245 The firmware for this driver must be extracted from the MacOS
246 driver beforehand. Tools for doing so are available at
247 http://bersace03.free.fr
248
249config USB_YUREX
250 tristate "USB YUREX driver support"
251 help
252 Say Y here if you want to connect a YUREX to your computer's
253 USB port. The YUREX is a leg-shakes sensor. See
254 <http://bbu.kayac.com/en/> for further information.
255 This driver supports read/write of leg-shakes counter and
256 fasync for the counter update via a device file /dev/yurex*.
257
258 To compile this driver as a module, choose M here: the
259 module will be called yurex.
260
261config USB_EZUSB_FX2
262 tristate "Functions for loading firmware on EZUSB chips"
263 help
264 Say Y here if you need EZUSB device support.
265 (Cypress FX/FX2/FX2LP microcontrollers)
266
267config USB_HUB_USB251XB
268 tristate "USB251XB Hub Controller Configuration Driver"
269 depends on I2C
270 help
271 This option enables support for configuration via SMBus of the
272 Microchip USB251x/xBi USB 2.0 Hub Controller series. Configuration
273 parameters may be set in devicetree or platform data.
274 Say Y or M here if you need to configure such a device via SMBus.
275
276config USB_HSIC_USB3503
277 tristate "USB3503 HSIC to USB20 Driver"
278 depends on I2C
279 select REGMAP_I2C
280 help
281 This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver.
282
283config USB_HSIC_USB4604
284 tristate "USB4604 HSIC to USB20 Driver"
285 depends on I2C
286 help
287 This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver.
288
289config USB_LINK_LAYER_TEST
290 tristate "USB Link Layer Test driver"
291 help
292 This driver is for generating specific traffic for Super Speed Link
293 Layer Test Device. Say Y only when you want to conduct USB Super Speed
294 Link Layer Test for host controllers.
295
296config USB_CHAOSKEY
297 tristate "ChaosKey random number generator driver support"
298 depends on HW_RANDOM
299 help
300 Say Y here if you want to connect an AltusMetrum ChaosKey or
301 Araneus Alea I to your computer's USB port. These devices
302 are hardware random number generators which hook into the
303 kernel entropy pool to ensure a large supply of entropy for
304 /dev/random and /dev/urandom and also provides direct access
305 via /dev/chaoskeyX
306
307 To compile this driver as a module, choose M here: the
308 module will be called chaoskey.
309
310config BRCM_USB_PINMAP
311 tristate "Broadcom pinmap driver support"
312 depends on (ARCH_BRCMSTB && PHY_BRCM_USB) || COMPILE_TEST
313 default ARCH_BRCMSTB && PHY_BRCM_USB
314 help
315 This option enables support for remapping some USB external
316 signals, which are typically on dedicated pins on the chip,
317 to any gpio.
318
319config USB_ONBOARD_HUB
320 tristate "Onboard USB hub support"
321 depends on OF
322 help
323 Say Y here if you want to support discrete onboard USB hubs that
324 don't require an additional control bus for initialization, but
325 need some non-trivial form of initialization, such as enabling a
326 power regulator. An example for such a hub is the Realtek
327 RTS5411.
328
329 This driver can be used as a module but its state (module vs
330 builtin) must match the state of the USB subsystem. Enabling
331 this config will enable the driver and it will automatically
332 match the state of the USB subsystem. If this driver is a
333 module it will be called onboard_usb_hub.
1#
2# USB Miscellaneous driver configuration
3#
4comment "USB Miscellaneous drivers"
5
6config USB_EMI62
7 tristate "EMI 6|2m USB Audio interface support"
8 ---help---
9 This driver loads firmware to Emagic EMI 6|2m low latency USB
10 Audio and Midi interface.
11
12 After firmware load the device is handled with standard linux
13 USB Audio driver.
14
15 This code is also available as a module ( = code which can be
16 inserted in and removed from the running kernel whenever you want).
17 The module will be called audio. If you want to compile it as a
18 module, say M here and read <file:Documentation/kbuild/modules.txt>.
19
20config USB_EMI26
21 tristate "EMI 2|6 USB Audio interface support"
22 ---help---
23 This driver loads firmware to Emagic EMI 2|6 low latency USB
24 Audio interface.
25
26 After firmware load the device is handled with standard linux
27 USB Audio driver.
28
29 To compile this driver as a module, choose M here: the
30 module will be called emi26.
31
32config USB_ADUTUX
33 tristate "ADU devices from Ontrak Control Systems"
34 help
35 Say Y if you want to use an ADU device from Ontrak Control
36 Systems.
37
38 To compile this driver as a module, choose M here. The module
39 will be called adutux.
40
41config USB_SEVSEG
42 tristate "USB 7-Segment LED Display"
43 help
44 Say Y here if you have a USB 7-Segment Display by Delcom
45
46 To compile this driver as a module, choose M here: the
47 module will be called usbsevseg.
48
49config USB_RIO500
50 tristate "USB Diamond Rio500 support"
51 help
52 Say Y here if you want to connect a USB Rio500 mp3 player to your
53 computer's USB port. Please read <file:Documentation/usb/rio.txt>
54 for more information.
55
56 To compile this driver as a module, choose M here: the
57 module will be called rio500.
58
59config USB_LEGOTOWER
60 tristate "USB Lego Infrared Tower support"
61 help
62 Say Y here if you want to connect a USB Lego Infrared Tower to your
63 computer's USB port.
64
65 This code is also available as a module ( = code which can be
66 inserted in and removed from the running kernel whenever you want).
67 The module will be called legousbtower. If you want to compile it as
68 a module, say M here and read
69 <file:Documentation/kbuild/modules.txt>.
70
71config USB_LCD
72 tristate "USB LCD driver support"
73 help
74 Say Y here if you want to connect an USBLCD to your computer's
75 USB port. The USBLCD is a small USB interface board for
76 alphanumeric LCD modules. See <http://www.usblcd.de/> for more
77 information.
78
79 To compile this driver as a module, choose M here: the
80 module will be called usblcd.
81
82config USB_LED
83 tristate "USB LED driver support"
84 help
85 Say Y here if you want to connect an USBLED device to your
86 computer's USB port.
87
88 To compile this driver as a module, choose M here: the
89 module will be called usbled.
90
91config USB_CYPRESS_CY7C63
92 tristate "Cypress CY7C63xxx USB driver support"
93 help
94 Say Y here if you want to connect a Cypress CY7C63xxx
95 micro controller to your computer's USB port. Currently this
96 driver supports the pre-programmed devices (incl. firmware)
97 by AK Modul-Bus Computer GmbH.
98
99 Please see: http://www.ak-modul-bus.de/stat/mikrocontroller.html
100
101 To compile this driver as a module, choose M here: the
102 module will be called cypress_cy7c63.
103
104config USB_CYTHERM
105 tristate "Cypress USB thermometer driver support"
106 help
107 Say Y here if you want to connect a Cypress USB thermometer
108 device to your computer's USB port. This device is also known
109 as the Cypress USB Starter kit or demo board. The Elektor
110 magazine published a modified version of this device in issue
111 #291.
112
113 To compile this driver as a module, choose M here: the
114 module will be called cytherm.
115
116config USB_IDMOUSE
117 tristate "Siemens ID USB Mouse Fingerprint sensor support"
118 help
119 Say Y here if you want to use the fingerprint sensor on
120 the Siemens ID Mouse. There is also a Siemens ID Mouse
121 _Professional_, which has not been tested with this driver,
122 but uses the same sensor and may therefore work.
123
124 This driver creates an entry "/dev/idmouseX" or "/dev/usb/idmouseX",
125 which can be used by, e.g.,"cat /dev/idmouse0 > fingerprint.pnm".
126
127 See also <http://www.fs.tum.de/~echtler/idmouse/>.
128
129config USB_FTDI_ELAN
130 tristate "Elan PCMCIA CardBus Adapter USB Client"
131 help
132 ELAN's Uxxx series of adapters are USB to PCMCIA CardBus adapters.
133 Currently only the U132 adapter is available.
134
135 The U132 is specifically designed for CardBus PC cards that contain
136 an OHCI host controller. Typical PC cards are the Orange Mobile 3G
137 Option GlobeTrotter Fusion card. The U132 adapter will *NOT* work
138 with PC cards that do not contain an OHCI controller. To use a U132
139 adapter you will need this "ftdi-elan" module as well as the "u132-hcd"
140 module which is a USB host controller driver that talks to the OHCI
141 controller within CardBus card that are inserted in the U132 adapter.
142
143 This driver has been tested with a CardBus OHCI USB adapter, and
144 worked with a USB PEN Drive inserted into the first USB port of
145 the PCCARD. A rather pointless thing to do, but useful for testing.
146
147 See also the USB_U132_HCD entry "Elan U132 Adapter Host Controller"
148
149 It is safe to say M here.
150
151config USB_APPLEDISPLAY
152 tristate "Apple Cinema Display support"
153 select BACKLIGHT_LCD_SUPPORT
154 select BACKLIGHT_CLASS_DEVICE
155 help
156 Say Y here if you want to control the backlight of Apple Cinema
157 Displays over USB. This driver provides a sysfs interface.
158
159source "drivers/usb/misc/sisusbvga/Kconfig"
160
161config USB_LD
162 tristate "USB LD driver"
163 help
164 This driver is for generic USB devices that use interrupt transfers,
165 like LD Didactic's USB devices.
166
167 To compile this driver as a module, choose M here: the
168 module will be called ldusb.
169
170config USB_TRANCEVIBRATOR
171 tristate "PlayStation 2 Trance Vibrator driver support"
172 help
173 Say Y here if you want to connect a PlayStation 2 Trance Vibrator
174 device to your computer's USB port.
175
176 To compile this driver as a module, choose M here: the
177 module will be called trancevibrator.
178
179config USB_IOWARRIOR
180 tristate "IO Warrior driver support"
181 help
182 Say Y here if you want to support the IO Warrior devices from Code
183 Mercenaries. This includes support for the following devices:
184 IO Warrior 40
185 IO Warrior 24
186 IO Warrior 56
187 IO Warrior 24 Power Vampire
188
189 To compile this driver as a module, choose M here: the
190 module will be called iowarrior.
191
192config USB_TEST
193 tristate "USB testing driver"
194 help
195 This driver is for testing host controller software. It is used
196 with specialized device firmware for regression and stress testing,
197 to help prevent problems from cropping up with "real" drivers.
198
199 See <http://www.linux-usb.org/usbtest/> for more information,
200 including sample test device firmware and "how to use it".
201
202config USB_EHSET_TEST_FIXTURE
203 tristate "USB EHSET Test Fixture driver"
204 help
205 Say Y here if you want to support the special test fixture device
206 used for the USB-IF Embedded Host High-Speed Electrical Test procedure.
207
208 When the test fixture is connected, it can enumerate as one of several
209 VID/PID pairs. This driver then initiates a corresponding test mode on
210 the downstream port to which the test fixture is attached.
211
212 See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more
213 information.
214
215config USB_ISIGHTFW
216 tristate "iSight firmware loading support"
217 select FW_LOADER
218 help
219 This driver loads firmware for USB Apple iSight cameras, allowing
220 them to be driven by the USB video class driver available at
221 http://linux-uvc.berlios.de
222
223 The firmware for this driver must be extracted from the MacOS
224 driver beforehand. Tools for doing so are available at
225 http://bersace03.free.fr
226
227config USB_YUREX
228 tristate "USB YUREX driver support"
229 help
230 Say Y here if you want to connect a YUREX to your computer's
231 USB port. The YUREX is a leg-shakes sensor. See
232 <http://bbu.kayac.com/en/> for further information.
233 This driver supports read/write of leg-shakes counter and
234 fasync for the counter update via a device file /dev/yurex*.
235
236 To compile this driver as a module, choose M here: the
237 module will be called yurex.
238
239config USB_EZUSB_FX2
240 tristate "Functions for loading firmware on EZUSB chips"
241 help
242 Say Y here if you need EZUSB device support.
243 (Cypress FX/FX2/FX2LP microcontrollers)
244
245config USB_HSIC_USB3503
246 tristate "USB3503 HSIC to USB20 Driver"
247 depends on I2C
248 select REGMAP_I2C
249 help
250 This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver.
251
252config USB_LINK_LAYER_TEST
253 tristate "USB Link Layer Test driver"
254 help
255 This driver is for generating specific traffic for Super Speed Link
256 Layer Test Device. Say Y only when you want to conduct USB Super Speed
257 Link Layer Test for host controllers.
258
259config USB_CHAOSKEY
260 tristate "ChaosKey random number generator driver support"
261 depends on HW_RANDOM
262 help
263 Say Y here if you want to connect an AltusMetrum ChaosKey to
264 your computer's USB port. The ChaosKey is a hardware random
265 number generator which hooks into the kernel entropy pool to
266 ensure a large supply of entropy for /dev/random and
267 /dev/urandom and also provides direct access via /dev/chaoskeyX
268
269 To compile this driver as a module, choose M here: the
270 module will be called chaoskey.